Environex Cleaning and Sealing Guide
Transcription
Environex Cleaning and Sealing Guide
Sandstone/Limestone and Masonry consolidator to harden and bind porous and friable surfaces. POISON CONTAINS 700 mL/L XYLENE, 167 g/L LIqUID HYDROCARBONS ‘5 YEAR WARRANTY & CSIRO tested’ * DEFEND (sandstone/limestone consolidator) DEFEND is a penetrating, invisible and breathable liquid that consolidates, hardens and binds the surface of porous DEFEND DEFEND DEFEND and friable surfaces, particularly limestones and sandstones. It will assist in the prevention of salt attack and surface breakdown common around swimming pools. DEFEND is also useful on less porous surfaces such as tile, brick, natural stone, paving and grout. Sealing with PINNACLE over DEFEND gives a 5 year warranty and sealing with TUSCAN over DEFEND gives a 3 year warranty. No Warranty will be given if the correct sealers are not used. Ensure surfaces to be treated are dry, clean and free of residues. Application: Saturate the surface with product using a clean brush, dip seal or a low-pressure hand spray. Avoid contact with surrounding areas. After 10 minutes, repeat the process. Total application rate is approximately 3-5 square metres per litre but is totally dependent on surface porosity. This allows for 2 saturating coats on most surfaces. POISON Quality ISO 9001 UDLY MAD RO E [email protected] www.environex.net.au P Manufactured by Environex International 19 Motivation Drive, Wangara, WA 6065 Ph: (08) 9302 4000 IN A U S T R A LI A Xn Harmful. N Dangerous for the Environment. R10 Flammable. R20/21 Harmful by inhalation and in contact with the skin. R37/38 Irritating to respiratory system and skin. R65 Harmful: May cause lung damage if swallowed. R51 Toxic to aquatic organisms. R53 May cause long-term adverse effects in the aquatic environment. SAFETY DIRECTIONS: When spraying solutions, we recommend a respirator mask be worn by the spray operator and anyone assisting in the spray operations. Use only when there is adequate ventilation available. Avoid contact with skin and eyes and avoid breathing vapour or spray mist. S16 Keep away from sources of ignition. FIRST AID: For advice, contact a Poisons Information Centre (Phone Australia 131 126) or a doctor (at once). If swallowed, do NOT induce vomiting. If in eyes, wash out immediately with water. If skin or hair contact occurs, remove contaminated clothing and flush skin and hair with running water. If inhaled, remove from contaminated area. Apply artificial respiration if not breathing. KEEP OUT OF REACH OF CHILDREN. READ SAFETY DIRECTIONS BEFORE OPENING OR USING. RO RO CSI and CSI and ed dedfor for test tee test teed ran gua gua ran S S AR YE YE AR 5 5 SALT ATTACK SALT ATTACK LIMESTONE LIMESTONE CONSOLIDATOR 1L [email protected] www.environex.net.au IN A U S T R A LI A Ensure adequate ventilation. Do not smoke or use naked flames while using. When preparing, wear elbow length PVC gloves and face shield. XN Harmful; N Dangerous for the Environment; Risks: R20/21 Harmful by inhalation and in contact with the skin; R36/37 Irritating to eyes and respiratory system; R65 Harmful: May cause lung damage if swallowed. R66 Repeated exposure may cause skin dryness or cracking. R67 Vapours may cause drowsiness and dizziness. R51 Toxic to aquatic organisms. R53 May cause long-term adverse effects in the aquatic environment. FIRST AID INSTRUCTIONS: For advice, contact a Poisons Information Centre (Phone Australia 131 126) or a doctor (at once). If swallowed, do NOT induce vomiting. If in eyes, wash out immediately with water. If skin or hair contact occurs, remove contaminated clothing and flush skin and hair with running water. If inhaled, remove from contaminated area. Apply artificial respiration if not breathing. 49357 Environex Endure-HiLite labels.indd 1 Batch No: 2 YE AR WARR Teste ANTY Australiand again for resis Stan st tance dard Salt Attac againsts k. Te s te d SALT ATTACK CONCRETE n and in use lung s in the n by the ntilation ep away a doctor skin or inhaled, ay mist. g, wear Centre in eyes, ing and artificial COVERAGE: Approximately 10 square metres per Litre, per coat. 2-3 coats are required depending on the porosity of the stone. More porous masonry requires more coats for adequate protection properties. IR CS NET CONTENTS 1L 4L 10L 20L SYNERGY is a new generation penetrating liquid that consolidates, hardens and binds the surface of porous and friable masonry materials. SYNERGY also possesses premium penetrating sealer properties to ensure maximum protection of the stone from permanent staining. SYNERGY has been scientifically developed and laboratory tested against Australian Standards. SYNERGY has been developed especially for use around all swimming pools to assist in prevention of salt attack and is warranted for a period of 2 years. DIRECTIONS FOR USE: ALWAYS TEST PRODUCT ON A SMALL AREA FIRST. Ensure surfaces to be treated are dry, clean and free from residue. Apply the first coat of SYNERGY to the masonry via lambswool applicator, brush or a low pressure Viton sprayer. It is ESPECIALLY IMPORTANT to apply SYNERGY to all surfaces including underneath the pool coping. (Use DEFEND for dip-sealing purposes prior to laying to avoid adhesion issues.) Apply the second coat when the first coat is dry, generally between 1-4 hours depending on ambient conditions. Note: The first coat will soak up more sealer per square metre than subsequent coats. Regardless two coats will average out as above. Actual coverage depends on the absorbency of the masonry. The denser the product the less sealer is required. CLEANUP: Clean all equipment with CYCLONE. FOR FURTHER TECHNICAL ASSISTANCE CALL 1800 999 196 EMERGENCY INFORMATION: FIRE: Foam, CO2, dry powder fire extinguishers. SPILLS: Eliminate ignition sources. Increase ventilation. Absorb onto earth, vermiculite or other absorbent material. Prevent entry into drainage systems, rivers, etc. Transfer into clearly labelled drums. Dispose of according to local government regulations. Additional information is listed in the Material Safety Data Sheet. In an emergency Dial 000 Police or Fire Brigade. 20/11/12 10:13 AM The Coatings ENDURE is a solvent based acrylic resin designed to give a wet look to surfaces where it is applied. It is typically associated with the gloss look of slate floors. ENDURE can be applied to slate, sandstone, and most types of pavers. It ENDURE is not suitable for terracotta or very dense surfaces such as porcelain, wet cast pavers, polished or honed surfaces. To apply, be sure that the surface is clean and dry. Always do a test patch especially on floors where an unknown sealer has been used. If any strange reactions happen, call our toll free number. We advise plans are made to sleep elsewhere on the night of application due to the odour of this product. Use a lambswool applicator and evenly spread the product on the floor. Do not allow pooling HI-LITE and remember thin even coats are best. More is not better with this product. After the first coat, allow around 2-3 hours before applying the second coat. In cold conditions this may be longer. Repeat the same process as the first coat ensuring no pools or puddles are left behind. Allow 12 hours before putting furniture back or walking on the floor. Any scratching of the sealer when POISON Batch No: KEEP OUT OF REACH OF CHILDREN. READ SAFETY DIRECTIONS BEFORE OPENING OR USING. ENDURE is a solvent based sealer designed to give a gloss finish to slate, sandstone, pavers, concrete and most masonry (not suitable for honed masonry). A hard wearing surface sealer, ENDURE will darken and highlight the colours of the surface while offering protection from normal household spills. A small test area is recommended. DIRECTIONS FOR USE: Ensure area to be sealed is clean and dry. Allow a minimum of 14 days drying time after laying new pavers. Do not apply to wet surfaces or surfaces that are below 10° Celsius or over 30° Celsius. A lambswool applicator will give best results. DO NOT USE A ROLLER. Product should be applied in thin coats with no pooling. At least 2 coats of sealer are recommended for normal domestic use, allow from 1-4 hours between coats (depending on atmospheric conditions) and 24 hours before heavy traffic. If in doubt seek advice from your Environex Stonecare Specialist. COVERAGE: For a finished job with 2 coats allow 5 square metres per litre. This coverage may be reduced on more porous surfaces. PROTECTS MASONRY AGAINST SOILING AND STAINING CLEANUP: Clean any affected areas and equipment using Environex CYCLONE. NET CONTENTS 1L 4L 10L 20L 200L POISON Batch No: KEEP OUT OF REACH OF CHILDREN. READ SAFETY DIRECTIONS BEFORE OPENING OR USING. 3 yE GUAR AR ANTEE AFTER BEFORE DARKENS AND HIGHLIGHTS THE NATURAL COLOURS OF STONE NET CONTENTS 1L 4L 10L 20L 200L mAINTENANCE: All masonry sealed with ENDURE should be routinely cleaned using Environex REFRESH as a routine cleaner or MAESTRO if there is a moss or mould buildup. RECOATING: ENDURE has a high life expectancy (2-3 years) dependent upon application, traffic conditions and level of maintenance. ENDURE should be the only sealer used in future for re-sealing – this will avoid any compatibility issues. If sealing over a surface that has previously been sealed, test a small area first. For best results always check with your Environex Technical Representative. FOR FURThER TEChNICAL ASSISTANCE CALL 1800 999 196 EmERGENCY INFORmATION : SPILLS: Eliminate ignition sources. Absorb onto earth, vermiculite or other absorbent material. Transfer into clean labelled drums for disposal. S29 Do not empty into drains. FIRE: S43 In case of fire, use sand, earth, chemical powder or foam. Water spray may be used to cool containers. Additional information is listed in the Material Safety Data Sheet. In an emergency Dial 000 Police or Fire Brigade. HI-LITE is a blend of solvent based sealers designed to darken the surface of sandstone, pavers, limestone, pebbles and concrete. It will highlight the colours of the surface without leaving the usual gloss level that can result in slippery surfaces. HI-LITE is ideal for concrete pavers and sandstone where a darker look is desired. On dense stone, a higher gloss level may result – always test first. HI-LITE will provide protection from normal household spillages. For a full gloss look use Environex ENDURE. APPLICATION: Should be done when the surface is clean and dry. A lambswool applicator or spray applicator will give best results. DO NOT USE A ROLLER. Product should be applied evenly across the surface ensuring no pools or puddles are left. Two coats are recommended with around 2-4 hours between coats depending on ambient conditions. Curing after final coat is overnight. If foaming occurs more sealer should be applied and foaming removed. It is normal for the first coat to leave a patchy result. The second coat will resolve this. COVERAGE: Allow 5 square metres per litre for a finished job. This can reduce on more porous surfaces. DRYING TIME: Allow 12 hours after final coat before walking or using the surface. CLEANUP: Cleanup applicators or spraying equipment using Environex CYCLONE. Applicators can be left to go hard – place them back in the sealer and they will soften in about 10 minutes. RECOATING: HI-LITE will last for 3-5 years depending on traffic. It is strongly advised that HI-LITE is the only sealer used in the future for resealing as there may be an adverse interaction between different sealers. TIPS: Do not seal if the temperature is below 10° Celsius or over 35° Celsius. If you are resealing – test a small area first. Once sealed, routine cleaning should be with Environex REFRESH or a neutral detergent. FOR FURTHER TECHNICAL ASSISTANCE CALL 1800 999 196 EMERGENCY INFORMATION: FIRE: S43 In case of fire use dry chemical, foam or carbon dioxide. Water spray may be used to cool exposed containers. SPILLS: Eliminate ignition sources. Collect liquid in an appropriate container or absorb onto earth, vermiculite or other noncombustible absorbent material. Transfer into clean labelled drums. Dispose of according to local government regulations. Additional information is listed in the Material Safety Data Sheet. In An Emergency Dial 000 Police or Fire Brigade. 18/12/12 12:21 PM CLEANUP: Clean any affected areas and equipment using Environex CYCLONE. 200L mAINTENANCE: All masonry sealed with ENDURE should be routinely cleaned using Environex REFRESH as a routine cleaner or MAESTRO if there is a moss or mould buildup. RECOATING: ENDURE has a high life expectancy (2-3 years) dependent upon application, traffic conditions and level of maintenance. ENDURE should be the only sealer used in future for re-sealing – this will avoid any compatibility issues. If sealing over a surface that has previously been sealed, test a small area first. For best results always check with your Environex Technical Representative. FOR FURThER TEChNICAL ASSISTANCE CALL 1800 999 196 EmERGENCY INFORmATION: SPILLS: Eliminate ignition sources. Absorb onto earth, vermiculite or other absorbent material. Transfer into clean labelled drums for disposal. S29 Do not empty into drains. FIRE: S43 In case of fire, use sand, earth, chemical powder or foam. Water spray may be used to cool containers. Additional information is listed in the Material Safety Data Sheet. In an emergency Dial 000 Police or Fire Brigade. ‘3 YEAR WARRANTY’ ** Batch No: 3 HI-LITE is a blend of solvent based sealers designed to darken the surface of sandstone, pavers, limestone, pebbles and concrete. It will highlight the colours of the surface without leaving the usual gloss level that can result in slippery surfaces. HI-LITE is ideal for concrete pavers and sandstone where a darker look is desired. On dense stone, a higher gloss level may result – always test first. HI-LITE will provide protection from normal household spillages. For a full gloss look use Environex ENDURE. CLEANUP: Cleanup applicators or spraying equipment using Environex CYCLONE. Applicators can be left to go hard – place them back in the sealer and they will soften in about 10 minutes. RECOATING: HI-LITE will last for 3-5 years depending on traffic. It is strongly advised that HI-LITE is the only sealer used in the future for resealing as there may be an adverse interaction between different sealers. TIPS: Do not seal if the temperature is below 10° Celsius or over 35° Celsius. If you are resealing – test a small area first. Once sealed, routine cleaning should be with Environex REFRESH or a neutral detergent. FOR FURTHER TECHNICAL ASSISTANCE CALL 1800 999 196 EMERGENCY INFORMATION: FIRE: S43 In case of fire use dry chemical, foam or carbon dioxide. Water spray may be used to cool exposed containers. SPILLS: Eliminate ignition sources. Collect liquid in an appropriate container or absorb onto earth, vermiculite or other noncombustible absorbent material. Transfer into clean labelled drums. Dispose of according to local government regulations. Additional information is listed in the Material Safety Data Sheet. In An Emergency Dial 000 Police or Fire Brigade. HI LITE is a sealer that provides a darkening of the surface without the normal slippery surface that can result (in most cases). It is suitable for indoor and outdoor use HI-LITE and is best suited to pavers where a darker look is desired. Not suitable for honed, polished or wet cast surfaces. Two coats applied evenly across the surface will give best results. A patchy appearance after one coat is normal. Application: Refer to the instructions for ENDURE. 2-4 coats as required. Not to be used on pool surrounds. Life span should be around 3-5 years dependent on traffic and conditions. Coverage: Allow approx. 5 square metres per litre for a finished job with 2 coats. yE GUAR AR ANTEE AFTER BEFORE DARKENS AND HIGHLIGHTS THE NATURAL COLOURS OF STONE NET CONTENTS 1L 4L 10L 20L 200L APPLICATION: Should be done when the surface is clean and dry. A lambswool applicator or spray applicator will give best results. DO NOT USE A ROLLER. Product should be applied evenly across the surface ensuring no pools or puddles are left. Two coats are recommended with around 2-4 hours between coats depending on ambient conditions. Curing after final coat is overnight. If foaming occurs more sealer should be applied and foaming removed. It is normal for the first coat to leave a patchy result. The second coat will resolve this. COVERAGE: Allow 5 square metres per litre for a finished job. This can reduce on more porous surfaces. DRYING TIME: Allow 12 hours after final coat before walking or using the surface. 18/12/12 12:21 PM STONESEAL is a water based acrylic sealer designed to give a satin finish to sandstone, slate and paving surfaces. It is suitable for indoor and outdoor use and is especially suited to Australian and Indian sandstones. Two coats will STONESEAL STONESEAL provide a tough seal on most surfaces that will resist staining from most household items. STONESEAL is not recommended around pools as it will result in a slippery and dangerous surface. Application: Apply product using a lambswool applicator. Two coats should be applied about 2 hours apart. Allow 12 hours for the final coat to cure. Surfaces should not be hotter than 35 degrees or colder than 10 degrees when applying STONESEAL. Do not allow pooling or puddling as this can dry to a weak spot in the sealer. If the surface is very porous 3 coats may be required for an even finish. Resealing should be done every 2-3 years and the old sealer should simply be cleaned with HD CLEANER prior to re sealing. Area should be rinsed with REFRESH. Cleanup is in water. Be sure to clean up before the sealer dries as it is difficult to remove after it has set. Coverage: Allow approx. 5 square metres per litre for a finished job with 2 coats. POISON KEEP OUT OF REACH OF CHILDREN. READ SAFETY DIRECTIONS BEFORE OPENING OR USING. SATIN FINISH SEALER SATIN FINISH SEALER NET CONTENTS 1L 4L LITRE 10L 20L 200L * When applied in accordance with the manufacturer’s simple directions and specifications a 5 year warranty is provided. Terms and conditions apply. Details available on request. ** When applied in accordance with the manufacturer’s simple directions and specifications a 3 year warranty is provided. Terms and conditions apply. Details available on request. ***When applied in accordance with the manufacturer’s simple directions and specifications a 2 year warranty is provided. Terms and conditions apply. Details available on request. CYCLONE: will remove ENDURE. MULTI STRIP: will remove STONESEAL. MULTI STRIP is a more aggressive stripper than CYCLONE and can be used to remove ENDURE, however it evaporates much quicker. MULTI STRIP should also be used where you are unsure as to the type of sealer on the surface. If this fails, call our toll free number. Application: Stripping a floor requires patience and good work practices. Always work a small area so that you keep control and remember that dry stripper is useless – it must be kept wet to be working. Apply the stripper by flooding it onto a small area (say 4 tiles). Scrub with a scrubbing brush to get the sealer and the stripper into a solution. Yes it is messy!! Wipe it off with a rag and throw the rag away. Repeat as necessary until the tile is bare. You will need lots of rags and we suggest a breathing apparatus as the fumes are nasty. Do not leave used rags on the floor as they can leave more sealer on the floor that is hard to remove. Continue across the floor until all tiles are bare. If Stripping ENDURE, a can of MULTI STRIP may be useful at the end for difficult areas. STRIP IT is a non-ammoniated stripping compound. This product has been specifically formulated for removal of acrylic metal cross-linked polishes such as LINK SEAL 30. It is recommended for use where the use of an ammoniated stripper is not desired. STRIP IT is essentially odourless and will not yield unpleasant vapours. Application: Prepare a 1:1 solution of STRIP IT in hot water and apply to the floor with a mop. Allow five minutes for the product to react with the polish. Machine scrub, at slow speed, using a black pad, or scrub with deck scrubber, scrubbing brush or stiff broom. Pick up the resultant slurry with a mop. Rinse the floor twice with clean, hot water and clean mop. STRIP IT may be used on the floor as a light strip where only a surface coat of polish needs removing. Use at a dilution rate of up to 1:10 in hot water. --------------------------------------------------------------------------------MULTI STRIP will evaporate quickly so only use it on small areas. MULTI STRIP can take paint off so take extra care around skirting boards. Cleaning AND Sealing Guide Manufactured by Environex International Pty Ltd 19 Motivation Drive, Wangara, WA 6065 Ph: (08) 9302 4000 Fax: (08) 9302 5000 FOR TECHNICAL ASSISTANCE CALL 1800 999 196 E: [email protected] W: www.environex.net.au Quality ISO 9001 UDLY MAD RO IN E contact se lung Vapours ng-term COMBINATION CONSOLIDATOR & SEALER FO LOw Rm G UL LO AT SS IO N 26) or O SALT ATTACK SANDSTONE n using nd skin. SYNERGY – COMBINATION CONSOLIDATOR & SEALER SYNERGY (combination consolidator & penetrating sealer in one) SYNERGY is a consolidator/hardening agent especially SYNERGY designed to stop salt attack around swimming pools. SYNERGY is truly two products in one. SYNERGY is a versatile product and is also ideal for use on all soft natural stone and masonry surfaces where consolidation is imperative to protecting your investment whilst still providing premium protection against staining. SYNERGY is also useful on outdoor stone and masonry furniture, pots and statues. Apply 2-4 coats with a lambswool applicator, paint brush or a low pressure hand sprayer. Always test a small area first. SALT ATTACK TRAVERTINE d skin. ‘2 YEAR WARRANTY & CSIRO tested’ *** 20L FO LOw Rm G UL LO AT SS IO N P Quality ISO 9001 UDLY MAD RO SAFETY DIRECTIONS: Avoid contact with eyes and skin. Avoid breathing vapour or spray mist. HAZARDOUS 10L KEEP OUT OF REACH OF CHILDREN. READ SAFETY DIRECTIONS BEFORE OPENING OR USING. E Ph: (08) 9302 4000 4L POISON Manufactured by Environex International 19 Motivation Drive, Wangara, WA 6065 20L 200L 10L CONSOLIDATOR COVERAGE: For a finished job with 2 coats allow 5 square metres per litre. This coverage may be reduced on more porous surfaces. PROTECTS MASONRY AGAINST SOILING AND STAINING NET CONTENTS CONTAINS 727 mL/L XYLENE; 75 g/L NAPHTHA; 20 mL/L BUTYL ACETATE SANDSTONE/LIMESTONE SANDSTONE/ CONSOLIDATOR SANDSTONE/ LITRE 1L 4L LITRE ENDURE is a solvent based sealer designed to give a gloss finish to slate, sandstone, pavers, concrete and most masonry (not suitable for honed masonry). A hard wearing surface sealer, ENDURE will darken and highlight the colours of the surface while offering protection from normal household spills. A small test area is recommended. DIRECTIONS FOR USE: Ensure area to be sealed is clean and dry. Allow a minimum of 14 days drying time after laying new pavers. Do not apply to wet surfaces or surfaces that are below 10° Celsius or over 30° Celsius. A lambswool applicator will give best results. DO NOT USE A ROLLER. Product should be applied in thin coats with no pooling. At least 2 coats of sealer are recommended for normal domestic use, allow from 1-4 hours between coats (depending on atmospheric conditions) and 24 hours before heavy traffic. If in doubt seek advice from your Environex Stonecare Specialist. UN 1866 RESIN SOLUTION, N.O.S. (XYLENE) CLASS 3 HAZCHEM 3[Y]E PG II NET CONTENTS Batch No: KEEP OUT OF REACH OF CHILDREN. READ SAFETY DIRECTIONS BEFORE OPENING OR USING. UN 1866, CLASS 3, RESIN SOLUTION FLAMMABLE, HAZCHEM 3[Y]E, PG III The Strippers P CONSOLIDATORS placing furniture back can be easily painted over with some more sealer. Cleaning and maintenance should be done with REFRESH and a re seal should be carried out every 2 years – more frequently for high traffic areas. Harsh cleaners such as Jif, Handy Andy or any acids should not be used on the sealed surface. Coverage: Allow approx. 5 square metres per litre for a finished job with 2 coats. Cleanup: Environex CYCLONE is to be used to clean up applicators. If you can dedicate an applicator for this job only, allow it to go hard and place in sealerENDURE 30 minutes before starting next time. The sealer will soften the brush or applicator. A U S T R A LI A CLEANERS Incorrect use of certain cleaners can cause permanent damage. Always add chemicals to water not water to chemicals. Always test a small area first. GROUT SMEAR REMOVER FOR SANDSTONE & TERRACOTTA NET CONTENTS 1L AMAZE is suitable for use on most surfaces – ceramics, vitrified and slate – for the removal of left over grout smear. AMAZE is a blend of acids that will cause a fizzing response on application but it is not as strong as ANTI‑EFF or GREEN DEVIL. Its best uses will be on slate and AMAZE ceramics where a minor grout smear problem has occurred. AMAZE Always use gloves and dilute in 5 parts water. Apply to the affected area and then scrub hard prior to mopping or removing the residue. It is best to work small areas at a time and rinse thoroughly. Do not use AMAZE on highly polished surfaces such as porcelain. Always use gloves, safety glasses and full length clothing. POISON HD CLEANER is a highly alkaline caustic cleaner designed for the cleaning of surfaces prior to sealing either for the first time or for later resealing. The strength of HD CLEANER makes it ideal to remove dirt deposits in kitchens or living areas that may have built up over time. HD CLEANER CLEANER HD Best results will be obtained with a dilution in 20 parts hot water. Flood the affected area and allow to stand for 2-3 minutes. Scrub vigorously until the solution on the floor is dirty and then mop off or remove with a wet vac. (The floor must be rinsed with REFRESH to take off any residue and left over dirt. Not to be used on polished surfaces.) Always use gloves, safety glasses and full length clothing. POISON DARKENS AND HIGHLIGHTS THE NATURAL COLOURS OF STONE 4L 10L 20L 200L LITRES HEAVY DUTY CLEANER FOR ALL SURFACES HEAVY DUTY NET CONTENTS LITRES 1L 4L ANTI‑EFF is a blend of acids designed to remove unsightly efflorescence salts and grout smear from pavers, terracotta and sandstone. Always wet the surface before application and dilute product with 15-25 parts water as per tech data, then neutralise with REFRESH and rinse. Mix away from surface to be treated. A fizzing reaction is normal. It is ANTI-EFF important to do a small area, get the product on and then scrub and rinse quickly. Always treat the whole area in a uniform manner and never use the product without diluting it. Never allow ANTI‑EFF to dry on the surface. Thorough rinsing is vital. (The floor must be rinsed with REFRESH to take off any residue and left over dirt. Not to be used on polished surfaces such as porcelain.) Suitable for most surfaces. Best use is on concrete pavers. Always use gloves, safety glasses and full length clothing. Coverage: One Litre should clean approx. 10 square metres. POISON Batch No: KEEP OUT OF REACH OF CHILDREN. READ SAFETY DIRECTIONS BEFORE OPENING OR USING. ANTI-EFF is a heavy duty acidic cleaner specifically designed to remove efflorescence from pavers, terracotta, slate or sandstone. As there are many issues surrounding efflorescence always consult your retailer or Environex International first. ANTI-EFF will react with and dissolve most surface salts that are the outcome of efflorescence. AFTER 1L 5L 15L [email protected] www.environex.net.au Ph: (08) 9302 4000 [email protected] www.environex.net.au IN A U S T R A LI A Quality ISO 9001 12/12/12 4:41 PM Quality ISO 9001 UDLY MAD RO IN A U S T R A LI A C Corrosive Risk Phrases: R 31 Contact with acids liberates toxic gas, R 34 Causes burns, R 8 Contact with combustible material may cause fire. Product will irritate the eyes, nose, throat and skin. SAFETY DIRECTIONS: S1/2 Keep locked up and out of the reach of children. S28 After contact with skin, wash immediately with plenty of water. S45 In case of accident or if you feel unwell, seek medical advice immediately (show the label where possible). S50 Do not mix with combustible material. Avoid contact with skin and eyes. Avoid contact with clothing. Avoid breathing vapour (or) spray mist. Ensure adequate ventilation when using. Use clean containers for dispensing. Store under cover in a dry, clean, cool, well ventilated place away from sunlight. Store and transport in an upright container. FIRST AID: For advice, contact a Poisons Information Centre (Phone Australia 131 126) or a doctor (at once). If swallowed, do NOT induce vomiting. If in eyes, hold eyelids apart and flush the eye continuously with running water. If skin or hair contact occurs, remove contaminated clothing and flush skin and hair with running water. 49210 Maestro multipack label-3.indd 1 [email protected] www.environex.net.au SD 6 is an alkaline iron stain remover that will rapidly convert yellow-brown insoluble iron stains to a pale green water-soluble solution. It will also convert other metal oxide stains such as manganese to soluble forms. SD 6 is a safe alternative to oxalic acid cleaners Application: Apply SD 6 neat or diluted with water, depending on the severity of the stain. Wash off immediately with tap water. If the surface is not washed off immediately, then air will re-convert the solubilized iron back to the insoluble form and the stain will return. VANISH Is a two part bleach cleaner designed for the cleaning of sandstone and transition metal colour bodies from siliceous surfaces. Do not use on man-made pavers. NOTE: Never use any acid on any marble, travertine or limestone surface. CLEANING TIP: Never let the surface dry and always rinse off thoroughly. Always test a small area first. SEALERS There are 2 types of sealer – those that penetrate and those which leave a surface coating. The penetrating sealers will leave a natural finish but may alter the colour depending on type of stone. The surface coatings will alter the appearance of the surface to differing degrees depending on which product is chosen. CHLORINATED CLEANER FOR REMOVING MOSS, MOULD & LEAF STAINS NET CONTENTS 5L 15L REFRESH REFRESH ROUTINE CLEANER FOR ALL SEALED CLEANER SURACES ROUTINE NET CONTENTS 1L 4L LITRE FOR ALL SEALED 20L 200L 10L SURFACES REFRESH (daily or weekly cleaner) is a pH Neutral Detergent designed for routine cleaning of all sealed surfaces. The product will gently clean and condition floors ensuring long sealer life. Dilute at 1:50 in warm water and mop on and then off the surface to be treated. Rinse with clean water to finish. S21 MULTI PURPOSE CLEANER is a remarkable hard surface cleaning concentrate which has outstanding grease cutting action through the incorporation of a broad range of sequestrants, surfactants and alkaline cleaning components. These components are further boosted with a specialty solvent component to synergistically dissolve and S21 MULTI PURPOSE CLEANER emulsify almost any grease or grime which can be encountered. The alkalinity of S21 MULTI PURPOSE CLEANER has been achieved without using caustic based products. Tyre Marks – Apply neat, allow to dwell on the stain for about 60 seconds, scrub with a stiff brush and rinse off with copious amounts of water. If the mark remains, repeat the process. CAUTION Batch No: KEEP OUT OF REACH OF CHILDREN READ SAFETY DIRECTIONS BEFORE OPENING OR USING DO NOT SWALLOW P S21 MULTI PURPOSE CLEANER is a remarkable hard surface cleaning concentrate which has outstanding grease cutting action through the incorporation of a broad range of sequestrants, sur factants and alkaline cleaning components. These components are further boosted with a specialty solvent component to synergistically dissolve and emulsify almost any grease or grime which can be encountered. The alkalinity of S21 MULTIPURPOSE CLEANER has been achieved without using caustic based products and as such will not affect aluminium surfaces. UDLY MAD RO IN A U S T R A LI A Quality ISO 9001 R36/38 Irritating to eyes and skin. S37/39 Wear suitable gloves and eye/face protection. FIRST AID: For advice, contact a Poisons Information Centre (Phone Australia 131 126) or a doctor (at once). If swallowed, do NOT induce vomiting. If in eyes, hold eyelids apart and flush the eye continuously with running water. Continue flushing until advised to stop by the Poisons Information Centre or a doctor, or for at least 15 minutes. If skin or hair contact occurs, remove contaminated clothing and flush skin and hair with running water. FLOOR SPARKLE is a heavy duty powerful water-based alkaline floor cleaner designed for safe and effective removal of heavy grease and oil deposits encountered in kitchen, food preparation areas and plant and machinery workshops. Light cleaning 1:100, Medium cleaning 1:50, and Heavy duty cleaning 1:10. FOR FURTHER TECHNICAL ASSISTANCE CALL 1800 999 196 POISON SAFETY DIRECTIONS: Strongly alkaline. Avoid contact with skin and eyes. 49231 S21 label-5.indd 1 APPLICATION is by way of watering can, bucket or straight from the bottle. Allow the product to dwell for 5 minutes and then scrub and rinse. Moss and mould will be easily removed and may even be hosed off. Leaf stains may require scrubbing but it is mainly the chemistry that will do the work. DO NOT SPILL THIS PRODUCT ON YOUR CLOTHES. Once clean rinse area thoroughly. KEEP OUT OF REACH OF CHILDREN. READ SAFETY DIRECTIONS BEFORE OPENING OR USING. Manufactured by Environex International 19 Motivation Drive, Wangara, WA 6065 Ph: (08) 9302 4000 Batch No: MAESTRO is a super concentrated chlorinated cleaner designed to remove moss, mould, leaf stains and timber tannin stains from tiles and pavers. It can be used neat or diluted – we suggest a dilution of 1 part MAESTRO to 4 parts water for most problems while difficult stains may need neat product. AFTER SAPPHIRE is a blend of acids and nonionic surfactants designed to remove stubborn stains such as red dirt etc. from hard surfaces such as masonry, ceramics, porcelain and glass. Do not use on concrete paving. Application: Apply SAPPHIRE diluted to 1:20 with hot water and apply to stains, allow to stand for a few minutes, then work with a brush or soft scouring pad (avoid scratching) and then rinse clean. 14/01/13 11:48 AM E BAN RUST is a remarkable blend of acidic cleaning agents which easily and rapidly converts those brownish coloured bore water stains allowing complete removal from all masonry and other building surfaces. BAN RUST also finds application in the marine industry for the removal of rust stains from fibreglass and other surfaces and water line staining caused by bacterial action. Application: BAN RUST is supplied in a ready to use form and incorporates a unique wetting agent to ensure total penetration into the stain to be removed. Use undiluted or 1-10 parts water (always test first). BAN RUST may be spray, brush or roller applied over contaminated surface. Allow 5-10 minutes duration or until stain has disappeared before flooding treated surface with water to remove any excess BAN RUST. For very heavily stained surfaces a second application of BAN RUST may be necessary. MAESTRO is a strongly chlorinated cleaner designed to remove organic stains such as moss and mould, leaf tannins and timber stains. It is best applied neat or diluted 1-5 parts water onto the affected area. Move the product around until the stains fade away – use a broom or a scrub brush MAESTRO – and then rinse thoroughly. Repeat if necessary. Do not get MAESTRO on clothing. Always use gloves, safety glasses and full length clothing. Coverage: One Litre should clean approx. 5 square metres. BEFORE Manufactured by Environex International 19 Motivation Drive, Wangara, WA 6065 UDLY MAD RO E Ph: (08) 9302 4000 NET CONTENTS UN 1791, HYPOCHLORITE SOLUTION, CLASS 8, HAZCHEM 2X, PG III FOR FURTHER TECHNICAL ASSISTANCE CALL 1800 999 196 Manufactured by Environex International 19 Motivation Drive, Wangara, WA 6065 CLEANER FOR 20LSURFACES 200L 10LALL HAZARDOUS CONTAINS MINIMUM 100 g/L AVAILABLE CHLORINE PRESENT AS SODIUM HYPOCHLORITE WHEN PACKED E EFFLORESCENCE REMOVER DIRECTIONS FOR USE: Always test first. ALWAYS WET THE SURFACE FIRST. Working in a small area, apply ANTI-EFF diluted at 1:25 to the affected area. A fizzing reaction may occur. Scrub hard using an eager beaver and rinse off immediately. LIMIT CONTACT OF ANTI-EFF WITH STONE TO NO MORE THAN 2-3 MINUTES. Repeat if necessary. We DO NOT recommend this product be used any stronger than 1:15 dilution in water as it can leach colour out of concrete pavers and masonry. MUST BE NEUTRALISED WITH REFRESH. If sealing allow a minimum of 2 days or until dry, must be clean and no traces of efflorescence left. P BEFORE GROUT SMEAR REMOVER SANDSTONE & 200L 10LFOR20L TERRACOTTA KEEP OUT OF REACH OF CHILDREN. READ SAFETY DIRECTIONS BEFORE OPENING OR USING. NET CONTENTS 1L 4L LITRES KEEP OUT OF REACH OF CHILDREN. READ SAFETY DIRECTIONS BEFORE OPENING OR USING. P Causes severe . Avoid contact 6 Wear suitable Centre (Phone do NOT induce ntinuously with by the Poisons If skin or hair n and hair with to stop by the tion is listed in GREEN DEVIL is a blend of acids best suited to removing grout smear from terracotta and sandstone. This product is NOT to be used on coloured concrete pavers. Mix with 10 parts water and flood onto a small area. A fizzing reaction is normal as the product attacks the cement smear. GREEN DEVIL GREEN DEVIL Scrub hard and rinse off thoroughly. Do not allow to dry on the surface. A stronger mix may be used on sandstone – up to 5 parts water for difficult stains. (The floor must be rinsed with REFRESH to take off any residue and left over dirt. Not to be used on polished surfaces such as porcelain.) Always use gloves, safety glasses and full length clothing. Coverage: One Litre should clean approx. 10 square metres. POISON KEEP OUT OF REACH OF CHILDREN. READ SAFETY DIRECTIONS BEFORE OPENING OR USING. CONTAINS 50 g/L ALKALINE SALTS HARD SURFACE CLEANER WITH OUTSTANDING GREASE CUTTING ACTION NET CONTENTS 1L 5L 15L 200L S21 MULTIPURPOSE CLEANER finds application in diverse areas including degreasing of automobile engines, industrial equipment, marine engines and bilges of boats, cooking ovens, aluminium filters in cooking fans, oily tools, kitchen work benches and stoves, grease removal from clothes and even grease removal and tyre marks from driveways and concrete surfaces. APPLICATION RATES: Engines, boat bilges, driveways etc. – Use neat or dilute 1:1 in hot water depending on degree of grease build-up. Work benches, stoves etc. – Dilute 1 part S21 MULTIPURPOSE CLEANER to 2 parts of water depending on the type of soil to be removed (more grease, lower dilution – less water). Greasy clothes – Add 150-300 mls per 7 kg of wash, or a normal household wash load. When adding to a washing machine S21 MULTIPURPOSE CLEANER should be diluted before addition to ensure no adverse effects from adding neat S21 MULTIPURPOSE CLEANER to clothes. Aluminium filters for cooking fume hoods – Dilute 1:10 with hot water and leave filter to soak for several hours. Agitation will improve grease removal. Tyre marks – Apply neat, allow to dwell on the stain for about 60 seconds, scrub with a stiff brush and rinse off with copious amounts of water If the mark remains, repeat the process. FOR FURTHER TECHNICAL ASSISTANCE CALL 1800 999 196 29/11/12 10:23 AM Penetrating Sealers ADVANTAGE is to be used on dense materials such as porcelain and granite. It will leave the surface with a natural finish (polished in the case of porcelain) and will protect against common spills. ADVANTAGE Preparation is the key to success with this product. ADVANTAGE The area to be sealed should be cleaned using a dilute HD CLEANER and all grout residue and dirt should be removed. Application: Apply product using a sprayer or lambswool applicator. One coat should be allowed to dry on the surface. Do not flood the product on – a good even thin coverage is best. For the second coat apply ADVANTAGE to a small area and then use a soft cloth or a white buffing pad if using a machine. This “spray buff” will bring out the natural finish of the surface. A polished porcelain will have a high polish as it does prior to grouting. Continue across the floor buffing small quantities of product until complete. Allow 2 hours for curing. Only clean treated floors with REFRESH. Cleanup is not necessary as applicators can be dusted out the followingday. Coverage: Allow approx. 20 square metres per litre for a finished job on most dense surfaces. More porous surface will use more product. POISON KEEP OUT OF REACH OF CHILDREN. READ SAFETY DIRECTIONS BEFORE OPENING OR USING. PENETRATING SEALER FOR PORCELAIN & DENSE STONE PENETRATING SEALER NET CONTENTS 1L 4L LITRE FOR PORCELAIN & 20L STONE 200L 10LDENSE CLEARSEAL A water based sealer best used as a pre seal to help with cleanup or as a sealer for masonry walls. Application is best done using a sprayer. Ensure only ONE COAT is applied and use only enough to soak the surface. Excess product should be wiped away while it is still wet. CLEARSEAL CLEARSEAL DO NOT LET POOLS AND PUDDLES SIT TO DRY. If any whitening occurs after drying too much product has been applied and you will need to call the hotline. Allow 6-8 hours before commencing grouting and be sure to wipe off all excess grout during cleanup. Cleanup is with water. Avoid spraying CLEARSEAL near timber or metal. Coverage: Allow approx. 3-5 square metres per litre. More porous surfaces may use even more. Resealing should be done every 3-5 years. POISON KEEP OUT OF REACH OF CHILDREN. READ SAFETY DIRECTIONS BEFORE OPENING OR USING. MASONRY SEALER AND PRE GROUT TREATMENT NET CONTENTS 1L 4L LITRE MASONRY SEALER AND PRE GROUT 20L 200L 10L TREATMENT ‘5 YEAR WARRANTY’ * PINNACLE is a blend of very high performing resins designed to give maximum stain protection from household spills. It is suitable for indoor and outdoor use and may PINNACLE alter the appearance of the surface being sealed (slight PINNACLE darkening may occur on some surfaces). It will not interfere with the finish or the slipperiness of the surface. Application: Apply product using a lambswool applicator or a solvent resistant spray pack for commercial areas. The area to be sealed must be clean and dry prior to sealing. Remember that any stains or marks that are sealed over will be almost impossible to remove later. Two light coats should be applied such that the surface is uniformly wet with the product, remove excess sealer, resealing 1-2 coats as required. Allow one hour between coats and 8 hours after completion before using the area. Ideally this is overnight. Maintenance and cleaning should be done using REFRESH. Harsh chemical cleaners such as acids, degreasers, Jif, Handy Andy should be avoided as they can break down the sealer quickly. Cleanup is not necessary as the resin in this product will turn to powder in the applicator. Simply dust off the following day. Surfaces sealed with PINNACLE will not require re sealing for many years and will not require stripping. After 5 years apply 1-2 coats of Pinnacle as required to protect your investment. Allow approx. 5 square metres per litre for a finished job of 2 coats. POISON KEEP OUT OF REACH OF CHILDREN. READ SAFETY DIRECTIONS BEFORE OPENING OR USING. PENETRATING SEALER FOR MAXIMUM STAIN PROTECTION PENETRATING SEALER FOR MAXIMUM STAIN 20L 200L 10L PROTECTION NET CONTENTS 1L 4L LITRE POISON KEEP OUT OF REACH OF CHILDREN. READ SAFETY DIRECTIONS BEFORE OPENING OR USING. ‘3 YEAR WARRANTY’ ** TUSCAN SEAL is a solvent based sealer designed to give stain protection from common spills. TUSCAN SEAL will leave the surface with a natural finish but may alter the TUSCAN TUSCAN SEAL appearance depending on the stone. Application: Apply product using a lambswool applicator or a chemical resistant spray pack. Do not allow to foam as it may cause staining (if foaming occurs there is not enough sealer being used). Two soaking coats are recommended with about 30 minutes between coats. Final curing takes about 2 hours. Coverage: Allow approx. 5 square metres per litre for a finished job on most surfaces. More porous surfaces will use more than this. Cleanup is not necessary – allow the applicator to dry and then dust out the next day. Resealing should be done every 3-5 years. Stripping is not necessary – clean area with HD CLEANER, GREEN DEVIL, SAPPHIRE, BAN RUST or ANTIEFF rinse with REFRESH and simply re-seal. PENETRATING SEALER FOR PROTECTION AGAINST PENETRATING SEALERSTAINING FOR ON TILES &AGAINST PAVERS PROTECTION NET CONTENTS STAINING ON LITRE 20L TILES 200L& PAVERS 1L 4L 10L FOR TECHNICAL ASSISTANCE CALL 1800 999 196 Always test a small area first and call us if in any doubt.