Eco Commercial Fans

Eco Commercial Fans
Installation Instructions
Original Instructions
2
Contents
General Description and Physical Specification
2-3
Wall Mounting Installation
4
Window Mounting Installation
5
Ceiling/Panel Mounting Installation
6
Pitched Roof Installation
7
Flat Roof Installation
8
Refurbishment Installation
9
Wiring Instructions
10
Integral Sensor and Remote Sensor/Remote Switch Installation
11
Superduct Fan Installation
12-13
Cleaning and Maintenance
14
CE Declaration
15
General Description and Physical Specification
•Warning: The appliance is not intended for use by young children or infirm persons unless they have been adequately
supervised by a responsible person to ensure that they can use the appliance safely. Young children should be
supervised to ensure they do not play with the appliance.
•Observe appropriate safety precautions if working on steps or ladders. Wear eye protection when breaking out wall
or window materials etc.
•When installing wall mounted fans, ensure that there are no buried cables or pipes in the way. It is recommended
that this fan is mounted 2.3m above floor level.
•A clearance of 75mm to be allowed on at least one side of the fan for the removal of the internal grille.
•Precautions must be taken to avoid the back-flow of gases into the room from the open flue of gas or other fuel
burning appliances (for duct and partition fans).
•This fan shall not be mounted above or closer than 1 metre to a cooker of other heat source where it could be
affected by excessive heat or moisture or sited where it would be suject to a direct source of heat in excess of 40˚C.
•After the fan is installed, its control system shall be in accordance with EN60335-2-80.
Greenwood Airvac
Technical Services Tel: 01903 777135
3
Dimensions
12” Fan
9” Fan
Front
6” Fan
Front
Front
342mm
420mm
342mm
420mm
Surface cable entry
Recessed
cable entry
269mm
Surface cable entry
Surface cable entry
Rear
Rear
Rear
Recessed
cable entry
214.5mm*
175mm*
Recessed
cable entry
137.5mm*
171mm*
206.5mm*
134.5mm*
342mm
413mm
* To centre of duct
Side
272mm
269mm
* To centre of duct
Side
130mm
169. 4mm
* To centre of duct
Side
128mm
Spigot Sizes for Ducted Applications
ck
Ceiling Adaptor
sa
Single Spigot Adaptor
sp
Single Spigot
idk
Induct Kit
CD12
350mm
350mm
350mm350mm
CD9
250mm
250mm
250mm250mm
CD6
200mm
200mm
200mm200mm
Fan Specifications
220-240 ~ 50Hz / 1Ph
IPX4:
CD12:100 watts
CD9: 50 watts
CD6: 38 Watts
Cable size required: 3 core 1.5mm2 / 4 core 1.5mm2.
Supply should be fused at 3 Amp.
The sound pressure of the Eco Commercial Fan is less than 70 dB(A).
Technical Services Tel: 01903 777135
Greenwood Airvac
4
Wall Mounting
Complete Kits CD12WA l CD9WA l CD6WA
1
EG12 l
EG9 l
EG6
ED12 l ED9 l ED6
Individual Units
CD12 l CD9 l CD6
2
6
10
3
7
11
4
8
12
5
9
13
Wiring – Page 10
Min. duct length 200mm
D
Eco 12”
D = 410 x 410 mm
Eco 9”
D = 330 x 330 mm
Eco 6”
D = 260 x 260 mm
Greenwood Airvac
Technical Services Tel: 01903 777135
5
Window Mounting
Complete Kits CD12WA l CD9WA l CD6WA
1
ED12 l ED9 l ED6
Individual Units
CD12 l CD9 l CD6
2
6
10
3
7
11
4
8
12
5
9
13
Wiring – Page 10
D
Eco 12” D = 337 mm
Eco 9”
D = 260 mm
Eco 6”
D = 184 mm
Technical Services Tel: 01903 777135
Greenwood Airvac
6
Ceiling/Panel
Mounting
Complete Kits CD12CK l CD9CK l CD6CK
1
D
Eco 12”
D = 430 x 430 mm
Eco 9”
D = 340 x 340 mm
CK12 l ck9 l ck6
Individual Units
Eco 6”
D = 270 x 270 mm
5
CD12 l CD9 l CD6
2
6
9
7
10
8
11
3
Wiring – Page 10
4
Greenwood Airvac
Technical Services Tel: 01903 777135
7
Pitched Roof Installation
Complete Kits CD12PR l CD9PR l CD6PR
EXPLODED VIEW
Weather Terminal (WT12/WT9/WT6)
Lead Flashing
Wall Fixing Plate (WFP12/WFP9/WFP6)
Spacer (WS12/WS9/WS6)
Single Spigot Adapter (SA12/SA9/SA6)
Weather Terminal
Worm Drive Fixing Clips
The Installation is made by screwing (8. off
5 mm dia. screws not provided) a Wall Fixing
Plate (WFP6/9/12) to suitably spaced purlins/
trimmers and weather-sealing this to the
structure with a lead or zinc apron.
The trimmed opening size is:–
l
6” Fan = 320 x 320 mm
l
9” Fan = 385 x 385 mm
l
12” Fan = 450 x 450 mm
To complete the water-tightness of the
installation, drill out the 4 dimpled hole
positions (6 mm dia.) in the base of the
Weather Terminal (WT6/9/12), place this
centrally on the Fixing Plate, with its lower
Flexible Ducting
edge sealed by silicon mastic, and then, using
the M5 screws, washers and seals provided,
attach the Weather Terminal to the Spacer
Moulding (WS6/9/12).
With the installation now weather-tight, the
Fan may be fitted into the Spacer as convenient.
Once the Fan is fitted, the Spigot Adaptor
(SA6/9/12) may be screwed to its lower face
and ducting attached as required.
On 6” Fans, the Spigot Adaptor may be
replaced by a Multi-Spigot Adaptor (MS6)
which will accept up to 4 – 100 mm dia.
individual ducts.
Dimensions
Weather Terminal
Wall Fixing Plate
Plan
Plan
WT12: 506 x 506mm
WT9: 425 x 425mm
WT6: 360 x 360mm
Side
WT12: 185mm
WT9: 180mm
WT6: 170mm
WFP12: 550 x 550mm
WFP9: 475 x 475mm
WFP6: 400 x 400mm
WFP12: 337mm dia.
WFP9: 260mm dia.
WFP6: 185mm dia.
Side
Single Spigot Adaptor
Spacer
Plan
Plan
WS12: 425 x 425mm
WS9: 341 x 341mm
WS6: 271 x 271mm
SA12: 430 x 430mm
SA9: 345 x 345mm
SA6: 275 x 275mm
Side
SA12: 70mm
SA9: 70mm
SA6: 70mm
WFP12: 2mm
WFP9: 2mm
WFP6: 2mm
Side
WS12: 137mm
WS9: 123mm
WS6: 126mm
SA12: 350mm dia.
SA9: 250mm dia.
SA6: 200mm dia.
Technical Services Tel: 01903 777135
Greenwood Airvac
8
Flat Roof Installation
Complete Kits CD12FR l CD9FR l CD6FR
EXPLODED VIEW
Roof Terminal RT6 / RT9 / RT12
Spacer WS6 / WS9 / WS12
Roof
Felt
Roof
Felt
AxB
O/all Finished Curb
Roof
Slab
Fan
Ceiling
Panel
Roof
Slab
Roof
Slab
Ceiling
Panel
Ceiling
Panel
Grille
150
mm
Roof
Felt
CxD
Ceiling Opening
The Installation is made by constructing a
timber or builders-work curb to the
dimensions shown below:
A
B
C
D
(max.)(max.)(max.)(max.)
CD6 610mm610mm300mm300mm
centrally and squarely over the curb and screw
the Terminal to the curb using 6mm Wood
Screws and Sealing Washers.
Offer the Spacer (WS6, WS9 or WS12) to the
underside of the secured Terminal and attach
using the 4.off M5 screws provided.
Attach the fan to the Spacer, again using the
screws provided, and complete the electrical
CD12695mm695mm450mm450mm wiring as required.
CD9 610mm610mm450mm450mm
To complete the installation, drill out the 8.off
dimpled holes in the base of the Roof Terminal
(RT6, RT9 or RT12), position the Terminal
The ceiling opening should be closed using a
suitable 300 x 300mm grille (CD6 fan) or
450 x 450mm grille (CD9 or CD12 fans).
Dimensions
Weather Terminal
Spacer
Plan
Plan
WS12: 425 x 425mm
WS9: 341 x 341mm
WS6: 271 x 271mm
RT12: 506 x 506mm
RT9: 425 x 425mm
RT6: 360 x 360mm
Side
Side
WS12: 137mm
WS9: 123mm
WS6: 126mm
RT12: 185mm
RT9: 180mm
RT6: 170mm
RT12: 742 x 742mm
RT9: 657 x 657mm
RT6: 657 x 657mm
Greenwood Airvac
Technical Services Tel: 01903 777135
9
Refurbishment Installation
Complete Kits CD12RE l CD9RE l CD6RE
Replacing existing Greenwood
Eco Fans
Replacing existing Greenwood Eco fan
The fan is fixed as the previous fan into the
existing channels on the wall liner. The picture
frame can be used if desired, however the
metal brackets are not required.
Replacing existing T series Fans
The brackets supplied with the kit can be
aligned with the screw fixing holes of the
previous fan. This then positions the receiving
nut on the bracket in the correct location to
allow fixing of the Greenwood refurbishment
fan.
Wiring details – Greenwood Eco Fans
When replacing Greenwood fans in many cases
the wiring will remain the same, however if the
existing controller is of the RC1 or RC2 type
installed with CX fans, then the switch
functionally changes. The RC1 switch becomes
an intake/off/extract switch operating the fan
on high speed only. The RC2 switch maintains
the on/off/auto functions, but at installation the
direction is selected.
Replacing existing T series fan
Wiring details – T series Fans
A Greenwood CD fan can be used to replace a
Vent Axia ‘T’ Series fan, retaining the original
controller, providing the controller is of the
‘Ecotronic 130’, ‘Rangemaster’ or ‘T’ Series
Controller type.
This arrangement will give the
following operating features:
• Adjustable speed
• Adjustable minimum speed
Vent Axia Ecotronic 130 or Rangemaster Controller
Greenwood Eco
Type CD
Reversible Fan
Vent Axia Ecotronic 130 or Rangemaster Controller
Greenwood Eco
TypeL5
CD
Reversible Fan
L4
• Extract/intake
L5
L3
• Fan off – shutter closed.
Limitations are:
• Control of single fan only
• Integral sensors not possible
230v ~ 50hz
230v ~ 50hz
• Fan off – shutter open
L4
L2
L3
L1
N
L2
N
L
Double-Pole
N Isolator
L
• Automatic ECO setting not available.
Double-Pole
Isolator
Max
5 amp
Max
5 amp
This arrangement will give the
following operating features:
• Single speed
• On/off.
Limitations are:
• Control of single fan only
• Integral sensors not possible
• Automatic ECO setting not available.
NB. All electrical products must be wired and
installed by a qualified electrician in accordance
with IEE and local regulations which apply.
The fans must be connected to mains power by
using a fused double pole isolating switch
having a contact separation of at least 3mm.
Technical Services Tel: 01903 777135
Double-Pole
Isolator
230v ~ 50hz
230v ~ 50hz
• Extract/intake
N
N1
L3
L1
L2
L
N
N1
L3
L1
L2
N
Greenwood Eco
Type CD
Reversible Fan
Vent Axia T-Sereis Controller
Greenwood Eco
TypeL5
CD
Reversible Fan
L4
L
Max
5 amp
L1
Vent Axia T-Sereis Controller
Max
5 amp
L
N Double-Pole
Isolator
L
N
L
L
N
N
L2
L5
L3
L1
L4
L2
L2
L3
L3
L1
L1
N
L2
N
L3
L1
N
N
NB. The ‘T’ Series controller speed capacitor must be removed from the
controller before use with a Greenwood ECO fan.
Greenwood Airvac
10
Wiring Instructions
1
2
Double-Pole Max
3 amp
Isolator
L
N Double-Pole
Isolator
L
All electrical products
should be wired and installed by a
qualified electrician,
N in accordance with IEE or local regulations
CXPC Fan Unit
which apply.
Max
3 amp
L
N
L connected to mains power by using a fused
The fans must be
N switch having a contact separation of at
double pole isolating
least 3mm.
For other siting
appliances
please refer to supplier data sheets
CX Fan
Unit
available on requested.
L5
Always isolate appliance
from the mains before cleaning.
L4
CX L3
Fan Unit
Do not use solvents
to clean the fan.
L2
L5
L1
L4
N
L3
Isolator
L4
L L2
Switch
RC1
L3
Max
3 amp
N
NL L4
L2
L
N
L3
L2
L1
N
Fan with Automatic operation
by Remote Sensor
N N
Link L2 – L4
for Extract
Remote Sensor
230v ~ 50hz
230v ~ 50hz
L1 L2 N
Double-Pole Max
Isolator
3 amp
L
N Double-Pole
Isolator
Remote Sensor
L1 L2 N
Max
3 amp
L
N
Link L2 – L3
for Intake
CD Fan Unit
CD Fan Unit
Link L2 – L4
for Extract L5
Link L2 – L3
for Intake L5
L4
CD Fan
L3 Unit
L4
CD Fan
L3 Unit
L5
L2
L4
L1
L5
L2
L4
L1
L3
N
L2
L3
N
L2
L1
L1
N
N
Link L2 – L4
Link L2 – L3
Only required if Fan unit is to be
Fan SWL
without Controller
switched by
Integral Sensor
for Extract
for Intake
CD Fan Unit
Only required if Fan unit is to be
230v ~ 50hz
230v ~ 50hz
SWL
L
N Double-Pole
Isolator
Max
3 amp
L
N
SWL
Only required if Fan unit is to be
Remote Sensor
230v ~ 50hz
230v ~ 50hz
230v ~ 50hz
Only required if L1
Fan unit
L2is toNbe
SWL 2-position
Fan with
Switch
Double-Pole Max
Isolator
3 amp
Remote Sensor
L1 L2 N
L
N Double-Pole
L
L
N
N
Max
Max
Double-Pole
Isolator
3 amp
3 amp
Isolator
L
Double-Pole Max
Isolator
3 amp
L
Double-Pole Max
N Isolator 3 amp
L
N
Link L2 – L4
for Extract L5
L4
CD Fan
L3 Unit
L5
L2
L4
L1
L5
L2
L4
L1
L3
N
L2
L3
N
L2
L1
L1
N
N
Link L2 – L3
for Intake
CD Fan Unit
CD Fan Unit
Link L2 – L4
for Extract L5
Link L2 – L3
for Intake L5
L4
L4
CD Fan
CD Fan
L3 Unit
L3 Unit
At Installation,
set link on Terminal Block
Cover
L5to L3 to give intake or L2
L5
L2
L4
to
give
extract.
L4
L4
L1
L1
L3
N
L2
L3
N
L5L2
L4L1
L3
N
L2
L1
N
L1
N
N
CD Fan Unit
Switch
RC3
L4
Switch
L L3
RC3
L2
L4
LN L3L1
N
Switch
L2
RC3
N L1
L4
N
L L3
L2
N L1
N
Fan with Remote Switch RC4 and Remote
Remote
L1 L2 NSensor
Link L2 – L3
for Intake L5
Link L2 – L4
for Extract
Double-Pole Max
Isolator
3 amp
L
N
CD Fan Unit
L4
CD Fan
L3 Unit
Double-Pole Max
Isolator
3 amp
Fan with Remote Switch RC3
230v ~ 50hz 230v ~ 50hz
230v ~ 50hz
Double-Pole Max
Isolator
3 amp
L
N Double-Pole
Double-Pole Max
Isolator
3 amp
Sensor
Switch
RC4
L1 L2 N Remote
L4
Sensor
Switch
L L3
RC4
L
L2
Double-Pole Max
N Isolator 3 amp
L4
LN L3L1
L1 L2 N Remote
N
L
Sensor
Switch
L2
RC4
N
L1
N
Double-Pole Max
L4
N
Isolator
3 amp
L L3
L
L2
N
N L1
Only required if Fan unit is to be fitted withN
integral ‘TA’ Timer
SWL
230v ~ 50hz 230v ~ 50hz
230v ~ 50hz
Switch
RC1
230v ~ 50hz
230v ~ 50hz
CXPC Fan Unit
N.B:
SWL
Only requiredMax
if Fan unit is to be fitted with integral ‘TA’ Timer
Double-Pole
L4
Fan with Isolator
Remote3 amp
Switch RC4
Switch
L and Integral Sensor
L3
RC4
L2
L4
L1
N L3
Only required if Fan unit is to be fittedLwith
integral ‘TA’ Timer
N
Switch
L2
RC4
L1
N
Double-Pole Max
L4
N
Isolator
3 amp
L L3
L2
N L1
N
L
Double-Pole Max
N Isolator 3 amp
SWL
L
N
L
N
L5
L4
CD Fan Unit
L3
L5
L2
L4
L1
L3
N
CD L2
Fan Unit
L5
L1
L4
N
L3
L2
L1
N
CD Fan Unit
L5
L4
CD Fan Unit
L3
L5
L2
L4
L1
L3
N
CD L2
Fan Unit
L5
L1
L4
N
L3
L2
L1
N
CD Fan Unit
Switch
RC4
230v ~ 50hz 230v ~ 50hz
230v ~ 50hz
230v ~ 50hz
230v ~ 50hz
4
3
L5
L4
CD Fan Unit
L3
L5
L2
L4
L1
L3
N
CD L2
Fan Unit
L5
L1
L4
N
L3
L2
L1
N
CD Fan Unit
Greenwood Airvac
Technical Services Tel: 01903 777135
11
Integral Sensor
1
4
7
2
5
8
3
6
9
Remote Sensor/Remote Switch
1
3
5
2
4
6
> 1.5m
> 200mm
Technical Services Tel: 01903 777135
Greenwood Airvac
Superduct Fan
SD100
SD150
SD200
SD250
80mm
80mm
80mm
80mm
Dimensions
SD100
Front
Front
44mm
Front
44mm
242mm
272mm
344mm
80mm
80mm
80mm
Side
Surface
cable entry
Side
Surface
cable entry
Front
Front
Front
Front
272mm
272mm
272mm
272mm
242mm
mm
242mm
344mm
SD250
44mm44mm
44mm44mm
Front
Front
Front
Front
344mm
344mm
344mm
344mm
344mm
344mm
344mm
344mm
80mm80mm
80mm80mm
80mm80mm
80mm80mm
SideSide
SideSide
Front
Front
Front
Front
344mm
344mm
344mm
344mm
230mm
230mm
230mm
230mm
44mm44mm
44mm44mm
402mm
402mm
402mm
402mm
80mm80mm
80mm80mm
SideSide
SideSide
SurfaceSurface
Surface
Surface
cable entry
cable cable
entry cable
entry entry
272mm
272mm
272mm
272mm
80mm80mm
80mm80mm
402mm
402mm
402mm
402mm
SideSide
SideSide
SurfaceSurface
Surface
Surface
cable entry
cable cable
entry cable
entry entry
198mm
198mm
198mm
198mm
SD315
230mm
344mm
344mm
344mm
344mm
344mm
344mm
344mm
344mm
242mm
2mm
SD100 l SD150 l SD200
l SD250 l SD315
44mm44mm
44mm44mm
80mm80mm
80mm80mm
SurfaceSurface
Surface
Surface
cable entry
cable cable
entry cable
entry entry
344mm
SD315
SD315
SD315
SD315
80mm80mm
80mm80mm
272mm
272mm
272mm
272mm
SideSide
SideSide
80mm
Surface
cable entry
230mm
80mm80mm
80mm80mm
SD200
44mm44mm
44mm44mm
Side
SD250
SD250
SD250
SD250
198mm
80mm80mm
80mm80mm
SD150
Front
Front
Front
Front
344mm
272mm
SD200
SD200
SD200
SD200
194mm
344mm
Surface
cable entry
242mm
SD150
SD150
SD150
SD150
44mm
344mm
242mm
Side
Front
44mm
272mm
SurfaceSurface
Surface
Surface
cable entry
cable cable
entry cable
entry entry
344mm
344mm
344mm
344mm
230mm
230mm
230mm
230mm
402mm
402mm
402mm
402mm
257mm
257mm
257mm
257mm
Wiring Instructions
SD100
Green/Yellow
Blue
Fan
N
Brown
L
Black
Green/Yellow
Black
Fan
N
Blue
L
Brown
Capacitor
230 V ~ 50 Hz
SD150, SD200, SD250 & SD315
230 V ~ 50 Hz
m
44mm44mm
12
Capacitor
N.B.:
All electrical products should be wired and installed by a qualified electrician, in accordance with IEE or local regulations which apply.
The fans must be connected to mains power by using a fused double pole isolating switch having a contact separation of at least 3mm.
For other siting applications please refer to supplier data sheets, available on request.
Always isolate appliance from the mains before cleaning.
Do not use solvents to clean this fan.
Greenwood Airvac
Technical Services Tel: 01903 777135
1
6
11
2
7
12
3
8
13
4
9
14
5
10
15
Technical Services Tel: 01903 777135
13
Greenwood Airvac
14
Cleaning / Maintenance
•Always isolate fan from mains before cleaning.
•For all fan sizes remove grille and clean in warm soapy water with a non-abrasive cloth.
•The impeller can be removed by carefully pulling the fan blades from either side at the same time.
These are to be cleaned in the same way as the above.
•The rear shutters can be cleaned but care must be taken when removing and replacing.
•Ensure that the shutter blades pins are correctly seated on the outside rim.
•Remove shutters via the retaining screws (3 will be found on the 6” and 9” models, 7 will be found
on the 12” model). Once removed, the shutter assembly can be cleaned in warm soapy water and must
be dried thoroughly before replacing.
•When replacing ensure that the shutter assembly blades are fully closed and that the assembly, as a
whole, is correctly seated before tightening the screws.
•When the shutter assembly has been replaced, ensure that the shutter blades are free to open by
placing a hand on either side of the shutter assembly blades and carefully opening.
•Once the interior grille shutter assembly has been cleaned, the fan’s main housing can be wiped with
a clean damp, non-abrasive cloth.
Greenwood Airvac
Technical Services Tel: 01903 777135
15
EC Declaration of Conformity/Incorporation
In accordance with EN ISO 17050-1:2004
Greenwood Air Management Ltd
Greenwood House, Brookside Avenue, Rustington, West Sussex,
BN16 3LF, UK
We
Of
In accordance with the following Directive(s):
2004/108/EC
2006/42/EC
The Electromagnetic Compatibility Directive
The Machinery Directive
hereby declare that:
Equipment
Model Number
Ventilation Fan
CD6 / ENERGY 500VE / CD9 / ENERGY 900VE / CD12 / ENERGY 1800VE
Is in conformity with the applicable requirements of the following documents
Ref. No.
Title
BS EN ISO 12100- Safety of machinery. Basic concepts, general principles for design
BS EN 60335-1
Household and similar electrical appliances. Safety. General
requirements
BS EN 60335-2-80 Household and similar electrical appliances. Safety. Particular
requirements for fans
BS EN 61000-6-1 Electromagnetic compatibility (EMC). Generic standards.
Immunity for residential, commercial and light-industrial
environments
BS EN 61000-6-3 Electromagnetic compatibility (EMC). Generic standards. Emission
standard for residential, commercial and light-industrial
environments
Edition/date
2003 =A1:2009
1&2
2002+A2:2006
2003
2007
2007
I hereby declare that the equipment named above has been designed to comply with the
relevant sections of the above referenced specifications and is in accordance with the
requirements of the Directive(s)
Signed by:
Name:
John Barratt
(full name of signatory)
Position: Business Process Manager
(position)
Done at:
As above
(place)
On :
02 February 2012
(date)
The technical documentation for the machinery is available from the manufacturer at the
above address.
Technical Services Tel: 01903 777135
Greenwood Airvac
Greenwood Air Management Ltd
Greenwood House, Brookside Avenue, Rustington, West Sussex BN16 3LF
Main Line Tel: +44 (0) 1903 771021
Technical Services: +44 (0) 1903 777135
Main Line Fax: +44 (0) 1903 782398
Web: www.greenwood.co.uk
Email: [email protected]
P541/132 Iss H May 2012 MCR708 PN05.10.114