OWNER`s MANUAL UTM Conversion SIG Sauer P229® SIG Sauer

OWNER’s MANUAL
UTM Conversion
SIG Sauer P229® (9 X 19)
SIG Sauer P226® (9 X 19)
PLEASE NOTE
For the safety of yourself and the safety of others, it is essential
to read and understand all owner documentation for all used UTM
products and all owner documentation for your firearm, particularly
all directions pertaining to clearing your firearm of all (potentially
live) ammunition. Prior to conversion and use of any UTM product,
read and understand the Owner Manual for your firearm, as well
the Owner Manual for your UTM conversion, the Owner Manual
for UTM Ammunition, and any directions or manuals for UTM
Targets, inserts, or other accessories. Careless use or intentional
misuse may result in injury or death to yourself or others.
Ultimate Training Munitions, Inc.
55 Readington Road
North Branch, New Jersey 08876
www.utmworldwide.com
(908) 725-9000
(877) 886-7233 toll-free
Your Conversion Serial Number:
SIG Sauer® Conversion and Accessories Manual (version 2.0)
INTENTIONALLY LEFT BLANK
FOR USER NOTES
WARNING! THE CARELESS USE, OR THE INTENTIONAL MISUSE, OF UTM
PRODUCTS MAY RESULT IN SERIOUS INJURY, DEATH, AND/OR PROPERTY
DAMAGE!
KEEP aLL UTM PRODUCTS OUT OF THE REACH OF CHILDREN! ADULT
SUPERVISION IS REQUIRED AT ALL TIMES IN CONNECTION WITH THE
USE OF UTM PRODUCTS. CHILDREN ARE ATTRACTED TO AND CAN
OPERATE FIREARMS, WHICH MAY RESULT IN SEVERE INJURIES OR
DEATH. PREVENT ACCESS BY CHILDREN TO ALL FIREARMS THAT ARE
NOT IN USE BY ALWAYS KEEPING THOSE FIREARMS OUT OF THEIR
REACH, UNLOADED AND LOCKED.
PROTECTIVE EYEWEAR MUST BE WORN BY ALL PERSONS WHO ARE
PRESENT WHEN UTM AMMUNITION IS BEING USED!
DO NOT USE UTM AMMUNITION NEAR DOORS, WINDOWS, HALLWAYS,
OR ANY OTHER AREAS WHERE PERSONS OR PETS COULD CROSS THE
LINE OF FIRE. IN ADDITION, DO NOT USE UTM AMMUNITION NEAR
ELECTRONIC EQUIPMENT, OR OTHER FRAGILE ITEMS THAT COULD BE
DAMAGED IF THEY WERE STRUCK.
TO AVOID THE RISK OF STARTING A FIRE, DO NOT DISCHARGE FIREARMS
NEAR FLAMMABLE MATERIAL!
BEFORE USING UTM PRODUCTS, CHECK YOUR LOCAL ORDINANCES,
IF ANY, REGULATING THE DISCHARGE OF FIREARMS. COMPLIANCE
WITH ALL APPLICABLE LAWS, RULES AND REGULATIONS IS THE SOLE
RESPONSIBILITY OF THE OWNER/USER OF UTM PRODUCTS.
(THE FOLLOWING INSTRUCTIONS ARE APPLICABLE ONLY TO THOSE
EDITIONS OF THE UTM TARGET SHOOTING KITS CONTAINING THE UTM
TARGET.)
CAUTION! ALWAYS INSPECT THE CARDBOARD TARGET INSERT PRIOR TO
EACH USE OF THE UTM TARGET SHOOTING KIT. DISCONTINUE USING
THE UTM TARGET SHOOTING KIT IF THERE IS EXCESSIVE WEAR TO THE
CARDBOARD TARGET INSERT.
PRIOR TO EACH USE OF THE UTM TARGET SHOOTING KIT, THOROUGHLY
INSPECT THE PROJECTILE TRAP PORTION OF THE TARGET FOR WEAR
OR DAMAGE. IF DAMAGE TO THE PROJECTILE TRAP IS VISIBLE, IT MUST
BE REPLACED IMMEDIATELY BEFORE ANY FURTHER USE OF THE UTM
TARGET SHOOTING KIT. CONTACT UTM FOR ASSISTANCE IN REPLACING
EITHER THE PROJECTILE TRAP, OR THE CARDBOARD TARGET INSERT.
PLEASE NOTE:
Prior to using UTM products, you MUST read and fully understand
all instructions, safety warnings, and usage instructions contained
in the documentation for your firearm and in the documentation for
you UTM conversion or product.
WARNING!
Always completely unload and then clean your firearm before
use with UTM conversions. ALWAYS clean the barrel after UTM
Ammunition. Remove any possible obstructions when cleaning the
unloaded firearm.
The UTM accessory target (sold separately) is intended only for
use with UTM Ammunition. Other use of the UTM target may be
unsafe.
Careless use or intentional misuse of a firearm, may cause result
in the discharge of that firearm. This may cause SERIOUS INJURY,
DEATH, or PROPERTY DAMAGE.
The UTM Ammunition should only be used in a well maintained,
properly functioning firearm, which has been converted using a
UTM Conversion.
All firearms that have been converted using the UTM Conversion
Kit and UTM Ammunition must be treated as a live firearm. Follow
all standard firearm safety rules. All users and bystanders must wear
eye protection.
If the firearm fails to fire, point the muzzle in a safe direction, wait
30 seconds and unload it carefully, avoiding the muzzle.
Discharging firearms in poorly ventilated areas, cleaning firearms,
or handling ammunition may result in exposure to lead, a substance
known to cause cancer, birth defects, reproductive harm and
illness or injury. Use in properly ventilated areas only. Wash hands
thoroughly after any exposure.
WARNING: KEEP OUT OF REACH OF CHILDREN.
PRIOR TO USE OF THE UTM CONVERSION
The UTM Conversion, combined with UTM Ammunition, will permit
full and realistic functioning of your firearm. Please note that the
UTM Conversion and UTM Ammunition should always be used
under the same operating guidelines that are specified by the
firearm manufacturer instructions, and in its instructions for the use
of conventional ammunition.
Be sure to follow all operating instructions provided by the firearm
manufacturer including, but not limited to, the cleaning and
lubrication of your firearm. The proper cleaning and lubrication
of your firearm is essential both to ensure your safety and for the
reliability of your firearm. Before firing any ammunition, the firearm
must be cleaned and lubricated. Most new firearms are coated with
protective grease that is great for preventing rust and corrosion, but
is not suited for lubricating the moving parts of a firearm.
In order to ensure the proper functioning of your firearm with the
UTM Conversion, and to ensure its reliability, you must properly
break in the firearm prior to using the UTM Conversion. To do
so, we recommend that the user fire, under normal operating
conditions, a minimum of 100 rounds of conventional ammunition
through the firearm.
INTENTIONALLY LEFT BLANK
FOR USER NOTES
CONTENTS
SECTION 1
Identify the components on the SIG SAUER® SECTION 2
PREPARE THE FIREARM FOR CONVERSION SECTION 3
REMOVE THE SIG® Live BARREL SECTION 4
LUBRICATE & INSTALL THE UTM BARREL SECTION 7
REMOVE THE UTM BARREL SECTION 5
1
3
5
7
10
TROUBLESHOOTING GUIDE 12
Limited Warranty Information 13
ADDITIONAL SAFETY WARNINGS 14
INTENTIONALLY LEFT BLANK
FOR USER NOTES
SECTION 1
Identify the components on the SIG SAUER®
SIG Sauer P229® Diagram
1. De-cocking Lever
2. Magazine Catch
3. Magazine
4. Slide Catch Lever
5. Take-down Lever
6. Slide Assembly
7. Frame
* Muzzle
The safety of yourself, others, and property depends on
understanding the firearm, its parts, and their function. Follow the
manufacturer’s instructions to clean, break in, and lubricate the
firearm.
Always make sure your firearm is unloaded and that the slide is
locked open in the rearward position with the magazine taken out
before beginning the installation of the UTM conversion kit. Always
Check Twice.
The following diagrams and directions are not intended to replace
a thorough understanding of the manufacturer directions and
guidelines for cleaning, lubricating, breaking in, and disarming the
firearm.
SIG Sauer® , SIG Sauer P226®, and SIG Sauer P229® are registered trademarks of
SIG Sauer Inc. Ultimate Training Munitions, Inc. makes no claim to any rights in these marks.
pg
1
KIT CONTENTS
UTM Conversion consists of a barrel exchange and utilizes all other
components from your traditional live firearm.
SIG Sauer P229® (9 X 19) conversion shown
pg
2
SECTION 2
PREPARE THE FIREARM FOR CONVERSION
WARNING!
CHECK TWICE to ensure chamber is EMPTY and the firearm is
CLEAR of any ammunition.
Please refer to your firearm owner manual from its manufacturer for
all recommended unloading procedures.
Protective eye-wear must be worn at all times when handling your
firearm.
Before disassembly of your firearm, you must take the following
steps to make sure that it is unloaded:
Keeping your finger off of the trigger and out of the trigger guard,
point your firearm in a safe direction.
Point your firearm in a safe
direction and depress the
de-cock lever (1)
Press the magazine catch
button. ( 2 )
Remove the magazine. ( 3 )
pg
3
Apply light upward pressure
to the slide catch lever ( 4 ).
Push the slide ( 6 ) back, to its
farthest position, engaging the
slide catch lever. (Note: you
must overcome spring pressure
to push the slide back.)
pg
4
SECTION 3
REMOVE THE SIG® LIVE BARREL
Refer to the Manufacturer’s instructions manual for the
recommended procedure on the removal of your barrel.
This manual has been designed to show the conversion process
in great detail. Please pay close attention to hand placement, and
firearm orientation, as this will ensure the conversion process is
performed in a correct and safe manner.
DISENGAGE the TAKE-DOWN LEVER
Hold the pistol in your right
hand with the muzzle slightly
elevated
Rotate the take-down Lever
(5) (located above the trigger)
to a vertical 6 o’clock position
(clockwise)
REMOVAL of the SLIDE ASSEMBLY
To remove the slide assembly (6)
grasp the slide from above and
slowly push it back.
When the slide is in its farthest
back position the slide catch
lever (4) will disengage and
allow the slide assembly to be
removed. Note: the slide catch
will drop on its own
Remove the slide assembly (6)
from the frame (7) with one
smooth motion.
pg
5
REMOVE THE RECOIL SPRING
Hold the slide (6) in the palm of
your hand with the muzzle (*)
of the barrel pointed away from
you, and the spring (9) upward.
Compress the Spring (9)
by squeezing the recoil spring
guide (8)
Swing the spring guide head (8)
upward until its head clears the
barrel (10)
Relax the recoil spring (9).
REMOVE THE SIG® BARREL
Hold the slide assembly (6) in
the palm of your hand with the
muzzle (*) pointed away from
you and the bottom side of the
slide upward.
Grasp the barrel (10) with your
thumb and index finger, press
forward slightly until barrel is
loose.
Lift the barrel upward ( 10) to remove it from the slide (6). Set the
live fire barrel aside.
Label and safely store your live fire barrel.
USE CAUTION!
When under pressure, the recoil spring could fly free of the
firearm and cause personal injury,damage to property, or injury
to persons nearby.
pg
6
SECTION 4
LUBRICATE & INSTALL THE UTM BARREL
Prior to inserting the UTM
conversion barrel, clean
the firearm as per the
manufacturer’s instructions.
Apply a small amount of
a quality lubricant that is
designed for firearms to the
sides, top and muzzle of the
conversion barrel.
Insert the conversion
muzzle ( * ) into the slide
( 5 ) opening.
Place the barrel into the
slide such that the barrel
can drop down into
place. Once the barrel
clears the ejector claw,
pull the barrel back to
seat it in the slide.
Squeeze the recoil spring and
spring guide. ( 8 & 9) Swing the
spring guide (8) end down until
its head seats in the barrel. The
locating notch in the barrel is
very small. Be sure the spring
is located correctly prior to
removing your hand from the
spring. Relax the recoil spring
and seat it into the barrel. (Be
careful to use just enough pressure to control the spring pressure).
Note:
Proper lubrication is essential for the correct function of the firearm.
pg
7
REPLACE the SLIDE ONTO the FRAME
Align the groves in the frame
(7) to the slots in the slide.
Slide the frame (7) onto the
slide (6)
Push the slide (6) back to its
farthest position while applying
constant light upward pressure to
the slide catch, (4)
(You must overcome the slide
spring pressure to engage slide
catch)
Rotate the take-down lever (5)
Counterclockwise to the three
o’clock position.
(Horizontal to the slide)
EXAMINE THE FIREARM
After assembly but before loading or inserting a magazine into the
firearm, cycle the firearm several times and check the following:
• The slide moves freely.
• The trigger and safety De-cocking lever function.
• The slide catch and magazine catch release function.
• Check all magazines in the pistol.
pg
8
The firearm is now ready for use with the UTM Conversion.
read and understand all instructions for the firearm,
conversion, and target ammunition, prior to using the
converted firearm.
WARNING!
NEVER attempt to load anything other than UTM
Ammunition into the converted firearm for ANY REASON.
pg
9
SECTION 7
REMOVE THE UTM BARREL
WARNING!
Refer to section 2, “Prepare the firearm for conversion” on page 3 to
ensure the firearm is clear of all ammunition.
DISENGAGE the TAKE-DOWN LEVER
Hold the pistol in your right hand
with the muzzle slightly elevated
Rotate the take-down Lever
(5) (located above the trigger)
to a vertical 6 o’clock position
(clockwise)
REMOVAL of the SLIDE ASSEMBLY
To remove the slide assembly (6)
grasp the slide from above and
slowly push it back.
When the slide is in its farthest
back position the slide catch lever
(4) will disengage and allow the
slide assembly to be removed.
Note: the slide catch will drop on
its own
If the slide does not easily
disengage from the frame, and
stops in the position shown, an
additional partial rotation of the
take-down lever may be required.
pg
10
Remove the slide assembly (6)
from the frame (7) with one
smooth motion.
Remaining conversion steps to go from the UTM barrel to your live
barrel will follow the process outlined in this manual (pg 6 onward).
Substitute the traditional barrel for the UTM barrel.
WARNING!
The firearm will now function for traditional live fire use. DO NOT
for any reason attempt to load target ammunition into a
firearm that is not converted for target ammunition. Only use
target ammunition in properly converted firearms.
NEVER fire live ammunition at targets intended for UTM
Ammunition.
pg
11
SECTION 5
TROUBLESHOOTING GUIDE
In the event of a malfunction when using a firearm with a UTM
conversion, please be sure to follow the troubleshooting steps
below prior to contacting UTM.
Malfunction
Possible Cause
Corrective Action
Cartridge is not
chambering.
Magazine is dirty.
Clean magazine.
Improperly lubricated,
or dirty firearm.
Clean and lubricate firearm as
per manufacturer’s instructions.
Slide will not close.
Chamber is dirty.
Clean barrel chamber.
Slide does not fully
cycle.
Excessively dirty or
improperly lubricated
firearm.
Clean and lubricate firearm
as per the manufacturer’s
instructions.
Properly lubricate UTM Barrel
Projectile not
leaving the barrel.
Obstruction in the
barrel, firearm is dirty.
Inspect the barrel for any
obstructions, clean as per
manufacturer’s instructions.
Failure to eject
fired cartridge.
Dirty chamber.
Clean and inspect the
chamber as per manufacturer’s
instructions.
Hammer strikes
with no discharge.
Defective round.
Maintain firearm in a safe
direction for 30 seconds
(delayed fire can occur). Cycle
the firearm ejecting the round
and chambering a new round.
Firearm does not
cycle.
UTM Conversion is
not properly seated.
Review installation instructions.
Improperly lubricated,
or dirty firearm.
Contact UTM Technical Support
for corrective instructions.
For additional technical support
Visit us on the web at: www.utmworldwide.com
E-mail: [email protected]
Technical support by phone:
Monday - Friday 8:00 a.m. to 5:00 p.m. (EST)
Toll Free: 1-877-886-7233
pg
12
Ultimate Training Munitions, Inc.
Limited Warranty Information
Warranty: Ultimate Training Munitions, Inc. (“UTM”) warrants that this firearm conversion
kit will be free of defects in design, workmanship and materials, for a period of twentyfour (24) months from the earlier of (i) the date of purchase; or (ii) the date on which the
original purchaser sells or transfers ownership of the product.
What this Warranty Does Not Cover: Normal wear and tear are not covered by this
Warranty. This Warranty also does not cover abuse, neglect, improper assembly,
improper use, improper maintenance, damage, failure to follow the instructions and
warnings provided, unreasonable use, rust or corrosion, barrel obstruction, target inserts,
the metal target backstop, or the like. This Warranty does not cover UTM ammunition.
The use in this firearm conversion kit of any ammunition other than the specified UTM
rounds will void this Warranty.
Obligations of UTM: In the instance of warranty claims for defects in this product, UTM
shall have the option to repair or replace this product (in either instance, with either
new or functionally equivalent and compatible parts, in the sole discretion of UTM) or,
if UTM is unable to repair or replace such products, to refund the purchase price for
any products found to be defective during the warranty period. In the instance of either
the misuse of the product, the unauthorized repair or modification of the products by
the customer, an accident to the product, or an act of God, UTM’s liability under this
warranty shall be null and void.
How to Obtain Service: Should a product need to be repaired or replaced, you must first
call (908) 725-9000 to receive a return authorization number, which will ensure that
your return package is properly received and processed. Please properly package and
insure any products being shipped for repair or replacement. UTM is not responsible for
loss or damage to products that occurs during shipping from you to UTM.
Limitations of Liability; Disclaimer: UTM shall have no responsibility or liability
whatsoever for product malfunction, or for physical injury, death and/or property
damage arising out of or relating to: criminal, reckless or negligent use of the product;
the improper or careless handling of the product; any unauthorized modifications of the
product; the use of improper ammunition; customer abuse or neglect of the product; the
failure of the customer to follow instructions and warnings provided; improper assembly,
use, or maintenance of the product; damage to the product; unreasonable use of the
product; rust or corrosion; barrel obstructions; the failure by the customer to follow
firearms safety and gun handling rules; the firing of conventional ammunition into the
UTM Target Shooting Kit; the failure to set up the product in a safe location; as well as
any and all other circumstances beyond the direct and immediate control of UTM.
THE REMEDIES PROVIDED TO THE PURCHASER HEREIN ARE THE EXCLUSIVE
REMEDIES AVAILABLE UNDER THIS WARRANTY, AND ARE INTENDED FOR THE
SOLE BENEFIT OF THE PURCHASER. NEITHER THIS WARRANTY, NOR ANY RIGHTS
HEREUNDER, ARE ASSIGNABLE. UTM SHALL HAVE NO LIABILITY UNDER THE
WARRANTY TO THIRD PARTIES TO THIS AGREEMENT. THE WARRANTY SET FORTH
ABOVE IS THE ONLY WARRANTY APPLICABLE TO THE PRODUCTS, AND ALL OTHER
WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE
ARE DISCLAIMED. IN NO EVENT SHALL UTM BE LIABLE IN CONTRACT, TORT,
OR OTHERWISE, FOR ANY DIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL
DAMAGES FOR, RESULTING FROM, OR IN CONNECTION WITH, THE USE OF THE
PRODUCTS.
Laws of Other Jurisdictions May Apply: This Warranty gives you specific legal rights. You
may also have other rights which vary from jurisdiction to jurisdiction.
pg
13
ADDITIONAL SAFETY WARNINGS
The UTM position on firearm safety:
• We place a heavy emphasis on firearms safety.
• UTM products are used with a real firearm and although they are considered safer
than target shooting using conventional live ammunition, you should nevertheless
always consider your firearm to be potentially lethal. Always handle and operate
your firearm as if you are shooting conventional live ammunition and always treat
every firearm as if it were loaded!
• Although your firearm will have been converted for use with UTM Ammunition, you
must observe all safety precautions as you would with a standard firearm. Abide
by all firearm safety rules, and remember that you - the Owner - are the ultimate
firearms safety device.
Guidelines for the safe use of the UTM Target Shooting Kit:
• WARNING! Always inspect your firearm to ensure it has been converted using the
UTM Conversion prior to firing it into the UTM cardboard target!
• DANGER! Ensure that you do not fire into the UTM cardboard target either a firearm
that has not been converted using the UTM Conversion, or a firearm that has been
converted back to conventional ammunition!
• Always wear eye and ear protection when converting firearms to prevent injury in
the event of an accidental discharge.
• Use UTM Conversions and UTM Ammunition only in conjunction with modern
firearms that are in good condition and that have been properly maintained.
• UTM Ammunition should only be used in a well maintained, properly functioning
firearm which has been converted using a UTM Conversion Kit.
• Ensure that there is no conventional ammunition available or present when using the
UTM Conversion. DO NOT, for any reason, attempt to load ANYTHING other than
UTM Ammunition into a firearm that has been converted using a UTM Conversion.
• Handle and store UTM Ammunition under live ammunition controls and conditions.
• The BORE and the CHAMBER of the host firearm MUST BE CLEANED AND
INSPECTED prior to firing UTM Ammunition.
• With the firearm unloaded, ALWAYS clean the barrel after using UTM Ammunition,
in order to remove any possible obstructions. Failure to do so prior to returning to
the use of conventional ammunition could result in SERIOUS INJURY / DEATH,
and/or damage to the firearm.
• UTM Ammunition is NOT re-loadable. Do not attempt to reload UTM Ammunition
cartridges.
• UTM Ammunition may discharge if the primer is struck. Handle UTM Ammunition
carefully, and do not drop it.
• UTM products should not be used near doors, windows, hallways, or other areas
where persons, pets, or property could be in the line of fire.
• UTM products should not be used near electronic equipment, or any other fragile
items that could be damaged if struck by a projectile or by an ejected cartridge case.
• Use only UTM Targets and inserts. Ensure the cardboard target inserts are properly
inserted into the projectile trap portion of the target.
• Prior to each use of the UTM Target Shooting Kit, thoroughly inspect the cardboard
target insert and the projectile trap portion of the target for wear or damage.
Discontinue using the UTM Target Shooting Kit if there is excessive wear to
the cardboard target insert, or if damage to the projectile trap is visible. IF THE
PROJECTILE TRAP IS DAMAGED, IT MUST BE REPLACED IMMEDIATELY BEFORE
ANY FURTHER USE OF THE UTM TARGET SHOOTING KIT. Contact UTM for
assistance in replacing either the projectile trap, or the cardboard target insert.
pg
14
•
Only shoot at the cardboard target. Shooting at anything other than the cardboard
target could cause ricochets, which can lead to personal injury and property
damage.
Some general statements about firearm safety:
• Safety is your responsibility. It is essential for your safety and the safety of others
that you abide by all firearms safety rules. If you are unfamiliar with firearms, you
should seek instruction and training through firearm safety courses provided by your
local gun clubs, by certified instructors, or by qualified organizations.
• Firearms should always be considered to be loaded and ready to fire. A loaded
firearm has the potential to seriously injure or kill. You, the handler, must personally
verify that the firearm is safe to handle. Never leave a firearm unattended, even if
the magazine is removed. Exercise extreme caution after removing the magazine.
You must personally verify that the chamber is empty before field stripping the
firearm for cleaning, or for any other reason.
• Always clean firearms before and after each use.
• Always keep your firearm unloaded until you are ready to use it. Store unloaded
firearms and ammunition separately, out of the reach of children and unauthorized
persons.
• Avoid jarring or dropping a loaded firearm, as this could cause an accidental discharge.
• It is always possible that ammunition may still be in the chamber of your firearm,
even though a loaded or empty magazine is removed or inserted. It is also possible
to accidentally chamber ammunition if the bolt is inadvertently closed on a loaded
magazine. Any ammunition in the chamber of a firearm will discharge upon pulling
the trigger. Always release and remove the magazine first, retract the bolt, and then
visually inspect both the chamber and the magazine to ensure that no ammunition
has been chambered. Always check twice!
• If your firearm has a safety, keep the safety engaged until you are ready to fire.
You should not, however, rely on safeties. Safeties are not a substitute for safe
gun handling. Never test safeties when a firearm is loaded or pointed in an unsafe
direction. Safeties can - and do - fail!
• Always keep your finger off the trigger and the trigger guard (including, but not
limited to, those times when you are loading, unloading, or converting the firearm)
until your sights are on the target!
• When squeezing the trigger of a firearm, you must expect the firearm to discharge.
You, and only you, are responsible for the consequences of a discharged firearm.
• Keep yourself and others clear of the firearm’s ejection port.
• All users and bystanders must wear eye protection.
• Never engage in horseplay while firearms are present – this could result in accidental
discharge and accompanying serious personal injury, death and/or property damage.
• Never use firearms while under the influence of drugs or alcohol. If you are on
medication, before using UTM products, talk to your doctor about whether it would
be safe for you to shoot.
• If the firearm fails to fire, keep it pointed in a safe direction, wait one minute, and
unload it carefully, avoiding the muzzle and keeping it pointed in a safe direction.
• Always keep firearms pointed in a safe direction!
• Never handle a firearm while anyone is downrange of the muzzle!
• Always know your target, your backstop, and what’s beyond them!
• Discharging firearms in poorly ventilated areas, cleaning firearms, or handling
ammunition may result in exposure to lead, a substance known to cause cancer,
birth defects, reproductive harm, and/or illness or injury. Use firearms only in a wellventilated area, and wash your hands thoroughly after exposure.
pg
15
Important
Please retain this manual with your UTM Conversion.
If you sell or otherwise transfer the product, please transfer this
manual as well to the new owner.
For more information about UTM
and about our other products:
Visit us on the World Wide Web:
www.utmworldwide.com
E-mail:
[email protected]
Phone us at:
1-908-725-9000
or 1-877-886-7233
Write us at:
Ultimate Training Munitions, Inc.
55 Readington Road
North Branch, New Jersey 08876
SIG Sauer® , SIG Sauer P226®, and SIG Sauer P229® are registered trademarks of
SIG Sauer Inc. Ultimate Training Munitions, Inc. makes no claim to any rights in these marks.
Copyright© 2016 Ultimate Training Munitions, Inc.
All rights reserved.
Manual P/N : IM-00002