new products 2015

Transcription

new products 2015

THETOOLMAKER
NEW PRODUCTS 2015
REV. 2
Kit/Tools suitable for timing
TIMING
Timing tool set suitable for VW Group 1.6 - 2.0 TDI CR engines - year 2012.
` AUDI: A3 Cabrio, A3 Saloon, A3 Sedan, A3/A3 Sportback, A4,
A4 allroad, A4 quattro, A5 Coupe/Cabriolet, A5 Sportback, A6, Q5, TT
` Engine: 1.6TDI CR, 2.0TDI CR, 2.0TDI CR Ultra
` Engine codes: CLHA, CNHA, CNHC, CRBC, CRBD, CRFA, CRFC,
CRKB, CRLB, CRLC, CSUA, CSUB, CUNA
` SEAT: Leon, Leon ST
` Engine: 1.6TDI CR, 1.6TDI CR Ecomotive, 2.0TDI CR
` Engine codes: CKFB, CKFC, CLHA, CLHB, CRBC, CRKB, CRLB, CRMB,
CRVA, CRVC, CUNA, CUPA
` SKODA: Octavia III
` Engine: 1.6TDI CR GreenLine, 2.0RS TDI CR, 2.0TDI CR, 2.0vRS TDI CR
` Engine codes: CKFB, CKFC, CLHB, CRKB, CRVC, CUPA
` VW: Golf SV/Sportsvan, Golf VII, Golf VII Estate, Golf VII Wagon, Polo
` Engine: 1.4TDI CR, 1.6TDI CR, 1.6TDI CR BlueMotion, 1.6TDI CR
BlueMotion Technology, 2.0GTD CR, 2.0TDI CR, 2.0TDI CR BlueMotion
Technology
` Engine codes: CKFC, CLHA, CLHB, CRBC, CRKA, CRKB, CRLB, CRMB,
CRVA, CUNA, CUSA, CUSB, CUTA
310 246 000
Variable camshaft timing kit suitable for FORD 1.0 engines.
` FORD: A3 B-MAX, C-MAX, Fiesta, Focus, Grand C-MAX, Transit Connect,
Tourneo Connect
` Engine: 1.0 EcoBoost, 1.0 SCTi EcoBoost
` Engine codes: M1DA, M1JA, M1JC, M1JE, M2DA, M2GA, P4JA, P4JB,
SFCA, SFCB, SFJA, SFJB,
2
310 247 000
GOVONI | Via degli Orsi, n. 97 | 40014 Loc. Beni Comunali | Crevalcore (BO) Italy | Tel.: +39.051.982688 | www.govoni.it
` OPEL: Corsa, Astra, Meriva, Zafira
` Engine: 1.0 - 1.2 - 1.4 ecoFLEX
` Engine codes: A10XEP, A12XEL, A12XER, LUJ/A14NET, LUJ/A14NEL,
LUH/A14NEL, LDD/A14XER, LDD/A14XEL
` CHEVROLET: Aveo
` Engine: 1.2 - 1.4
` Engine codes: LWD/A12XEL, LDC/A12XER, L2Q/A12XEL,
LDD/A14XER, LDD/A14XEL
TIMING
Timing tool set suitable for OPEL 1.0 - 1.2 - 1.4 ecoFLEX, chevrolet 1.2 - 1.4
petrol engines. INCLUDED: Crankshaft pulley holding tool
` ON REQUEST: Handle for crankshaft pulley holding tool
310 251 000
Timing tool set suitable for OPEL 1.0 - 1.2 - 1.4 ecoFLEX, chevrolet 1.2 - 1.4
petrol engines.
` OPEL: Corsa, Astra, Meriva, Zafira
` Engine: 1.0 - 1.2 - 1.4 ecoFLEX
` Engine codes: A10XEP, A12XEL, A12XER, LUJ/A14NET, LUJ/A14NEL,
LUH/A14NEL, LDD/A14XER, LDD/A14XEL
` CHEVROLET: Aveo
` Engine: 1.2 - 1.4
` Engine codes: LWD/A12XEL, LDC/A12XER, L2Q/A12XEL,
LDD/A14XER, LDD/A14XEL
` ON REQUEST: Crankshaft pulley holding tool and handle
GOVONI | NEW PRODUCTS CATALOGUE 2015
310 252 000
3
Glow plug removal kit
GLOW PLUGS
Tool set for M8-M9-M10 glow plugs removal with slide hammer.
` Indispensable solution to remove glow plugs stuck in their seat.
` This system quickly and directly grips the hex body of all types of
M8-M9-M10 glow plugs.
` Features the innovative fast lock system that ensures maximum
quickness.
` Does not damage the cylinder head and guarantees a job done to
professional standard.
` Removal through the strokes of the slide hammer provided.
` Glow plugs in modern CRs are highly stressed and also used as
"hot spots" not only when the vehicle starts (e.g.: to reduce emissions
to a minimum or to reduce the wear of the catalyst and, if present,
the DPF). As such, the glow plugs remain lit much longer while
heating, for the reasons outlined above.
hot
GEARBOX SUPPORTS
Glow plug removal kit
311 189 000
Engine support device
Universal engine support with telecopic and rotating arms.
` This special device allows to support the engine when the side
engine bracket is removed, e.g. during maintenance work on thrust
bearings, timing belts, water pumps or tensioner rollers.
` Equipped with two sliding hooks to fit to underbody of every
wehicle.
` After loosening the engine mount, the engine support safely holds the
vehicle engine in the engine compartment (time savings and higher
safety at work).
8°
` Universal tool for cars and commercial vehicles.
` Telescopic arm (to 230 mm)
` Load capacity 400 Kg
` Sliding telescopic arm extension: min. 657 / max 887
` Side-arms extension: min. 322 / max 566
` Arms rotation of 360°; the device can be closed completely in order
to be stored in small spaces.
` The 2 supporting feet are adjustable in height, covered with a nonslip rubber, they can float up to 8° adjusting to the surface.
hot
Engine support device
4
314 032 000
Clutch aligner set SAC
` The clutch aligner tool set is essential for mounting the gearbox properly
and for letting the clutch working properly. A correct clutch alignment, during
the mounting phase allows:
- To decrease vibrations
- To save fuel
- To decrease emissions
- No misalignment between engine and gearbox
- Long-lasting clutche
- Don’t void the warranty of the clutch
CLUTCH
Clutch aligner tool set, 20 pcs.
` The clutch aligner tool set can be used on all the brand and models of
vehicles
` TO BE USED with code: 318 010 000
hot
318 014 000
SAC clutch tool set
Special kit suitable for SAC clutches, CENTERING INCLUDED.
` This kit allows the easy dismounting, removal and replacement of all
self-adjusting clutches SAC (SAC = Self-Adjusting-Clutch).
` The kit includes a centring tool specific for SAC models with the diameter
of the crankshaft bore (driving bearing seat) bigger than the diameter of the
clutch hub and without the driving bearing.
` It is equipped with 2 plates: 3-arms and 4-arms (specific for MB), for
clutches with 6 or 8 locking holes.
` Note: with the 4-arms plate (code 318004002) it is possible to work on
all SAC clutches with multiple of 4 holes (ex: Mercedes A-Class
(up to 2004 W169).
318 015 000
5
SHOCK ABSORBERS
Spring locking tool
Kit di fissaggio molla ammortizzatore.
` This tool is necessary to fix the spring to the brackets during compression
and relaese operations since modern helical compression springs have
changed a lot over the years, increasing considerably the space within coils
and consequently the inclination of the supporting point relative to the bracket.
` By keeping firmly locked the coil to the bracket using this vice, the user can
work in complete safety also during the maximum spring compression
` Ultralight.
` Specific plastic scratchproof coat to protect the spring surface.
` It grants anchoring of the spring, avoiding accidents and injuries of the operator.
` Ideal for every model of coil spring compressor, necessary on tools without protections.
` Universal, ideal for springs with coil Ø13 - Ø26 mm
hot
Ø 13
8
` Supporting tool to be used with the spring strut compressor of GOVONI range:
321051000, 321055000, 321056000 and 321094000.
Ø 26
OK
NO
Spring locking tool
321 090 000
Diagnostic wheel alignment tool set for hubs and SOSPENSIONI
Special diagnostic tool set, necessary for strain detection on hubs, SOSPENSIONI
and rear axle; with this tool the operator is able to find the non-conforming parts that
have to be replaced because of collisions or potholes on the road.
` Able to identify with certainty the real reason which is compromising the
camber measure between hub and shock absorber.
` Use direclty on the hub wheel.
` Fast use and easy measurement of both hubs.
` Advantages of this GOVONI tool set are giving an immediate trial of the
balance problem, high time saving for indentifying the real damaged part
and finally high cost saving for the mechanic.
` Collisions or potholes on the road, sidewolks and crashes in general
causing damages on the suspension system and currupting the camber
measure. So are coming more and more problems of roadworthiness, and
unusual tyre usage.
hot
Diagnostic wheel alignment tool
6
321 104 000
Special device for swinging arms removal, suitable for cars and commercial vehicles.
`
`
`
`
Only one operator required to carry out the entire assembly.
Simultaneous removal of both oscillating arms.
Ultra-fast operation: use of impact gun.
Detachment through belt which guarantees utmost safety and keeps arms
intact.
` Sliding support feet to fit any underbody.
` Universal for cars and commercial vehicles.
` Suitable for all track widths.
HUBS - BEARINGS
Special device for swinging arms removal
hot
Special device for swinging arms removal
322 010 000
Press tool set for silent-blocks
Kit for silentblock introduction and extraction of rear deck, swinging arms, oil
seal crankshaft intriduction, camshaft.
` Suitable to all cars and commercial vehicle silentblock.
` The tool can be used without disassembling the arms or the trapeze
thanks to the tie-rods.
` Il helps the work on the press thanks to the available bushings.
` The bushes are from diam. 34 mm to diam 82 mm, they can be used
directly on the vehicle or under the press.
` Suitable for introduction and extraction of wheel bearings
Press tool set for silent-blocks mechanical
322 015 000
7
HUBS - BEARINGS
Press tool set for silent-blocks WITH HYDRAULIC CYLINDER
Kit for silentblock introduction and extraction of rear deck, swinging arms, oil
seal crankshaft intriduction, camshaft..
` Suitable to all cars and commercial vehicle silentblock.
` The tool can be used without disassembling the arms or the trapeze
thanks to the tie-rods.
` Il helps the work on the press thanks to the available bushings.
` The bushes are from diam. 34 mm to diam 82 mm, they can be used
directly on the vehicle or under the press.
` Suitable for introduction and extraction of wheel bearings
` Frame tested up to 12 ton (corresponding to the pressure of GOVONI
270025001 cylinder - 500 bar)
Press tool set for silent-blocks WITH hydraulic cylinder
322 018 000
Tool set for silentblocks
Universal tool set for silentblocks.
` The set is suitable for silentblock cars of all measures.
` It can be used without dismantling the swinging arms, thanks to its
tie-rod.
` It helps the work on the press thanks to diffents bearings available.
` The bearings can be used directly on the vehicle or under the press.
` Suitable for introduction/extraction of Silentblock of rear deck, of
engine support, swinging arms, introductions of crankshaft oilseals,
camshaft.
` Useful for introduction/extraction of wheel bearings
MECHANICAL
WORKING
MODULATE MOUNTING BUSHING
To remove SILENTBLOCK up to L = 100
Silentblock
Bush
Tool set for silentblocks
8
Bush
322 020 000
HUBS - BEARINGS
Tool set for silentblocks WITH HYDRAULIC CYLINDER
Tool set for silentblocks with hydraulic cylinder 17 ton.
` The set is suitable for silentblock cars of all measures.
` It can be used without dismantling the swinging arms, thanks to its
tie-rod.
` It helps the work on the press thanks to diffents bearings available.
` The bearings can be used directly on the vehicle or under the press.
` Suitable for introduction/extraction of Silentblock of rear deck, of
engine support, swinging arms, introductions of crankshaft oilseals,
camshaft.
` Useful for introduction/extraction of wheel bearings
HYDRAULIC
WORKING
Installation silentblock with hydraulic cylinder 17 t
Removal silentblock with hydraulic cylinder 17 t
Pushing bush
Silentblock
Silentblock
Pushing bush
Tool set for silentblocks WITH hydraulic cylinder
322 021 000
Tool set for hub/bearing WITH HYDRAULIC CYLINDER
Tool set for compact wheel hub/bearing unit - Ø 62 to Ø 85 mm. with hydraulic
cylinder 17 t. This UNIVERSAL Govoni kit is the solution to pull out and mount
the new Hubs with new Bearing Unit HBU2 (assembed unit including hubs and
bearings.
` The main features of the kit are efficiency and fast use, endurance and
heavy duty components.
` The main advantages are:
- UNIVERSAL disassembling system (suitable to all the models)
- Use directly on the vehicle
- Safety use in assembling/disassembling (no break or damage of
the hub)
- It reduces working time of 25% compared to common tools
` Thanks to its features, it can works on bearings from a diameter of
Ø62 mm to Ø85 mm.
HYDRAULIC
WORKING
BEARINGS
Ø 62
BRAND
Audi, VW
BEARINGS
Ø 72
BRAND
Audi, Seat
BEARINGS
Ø 66
Skoda
Ø 75
Mitsubishi, Smart
Ø 82
Ø 68
Citroën, Renault
Ø 78
Ford, Volvo
Ø 85
BRAND
Ford, Volvo
4x4, SUV
323 034 000
9
HUBS - BEARINGS
Tool set for compact wheel hub/bearing unit with hydraulic cylinder 17 t.
This UNIVERSAL Govoni kit is the solution to pull out and mount the new Hubs
with new Bearing Unit HBU2 (assembed unit including hubs and bearings.
` The main features of the kit are efficiency and fast use, endurance and
heavy duty components.
` The main advantages are:
- Use directly on the vehicle
- Safety use in assembling/disassembling (no break or damage of
the hub)
- It reduces working time of 25% compared to common tools
` INTRODUCTION: it can works on bearings from an external diameter of
Ø82 mm to Ø85 mm.
` EXTRACTION: it can works on bearings from an external diameter of
Ø62 mm to Ø85 mm.
` ON REQUEST: additional set for hub/bearing installation from Ø62 mm
to Ø78 mm
HYDRAULIC
WORKING
REMOVAL
BEARINGS
REMOVAL
BRAND
Audi, VW
Ø 72
Audi, Seat
Ø 66
Skoda
Ø 75
Mitsubishi, Smart
Ø 68
Citroën, Renault
Ø 78
Ford, Volvo
BEARINGS
BRAND
Ø 62
REMOVAL
hot
BEARINGS
INSTALLATION
BRAND
BEARINGS
BRAND
Ø 82
Ford, Volvo
Ø 82
Ford, Volvo
Ø 85
4x4, SUV
Ø 85
4x4, SUV
323 036 000
Tool set for Ø 62mm hub/bearing
Additional set for Ø 62mm hub/bearing installation.
INSTALLATION
BEARINGS
Ø 62
BRAND
Audi, VW
REMOVAL
Tool set for Ø 62mm hub/bearing
10
INSTALLATION
323 037 000
HUBS - BEARINGS
Tool set for Ø 66, Ø 68mm hub/bearing
Additional set for Ø 66, Ø 68mm hub/bearing installation.
INSTALLATION
BEARINGS
BRAND
Ø 66
Skoda
Ø 38
Citroën, Renault
REMOVAL
Tool set for Ø 66, Ø 68mm hub/bearing
INSTALLATION
323 038 000
Tool set for Ø 72, Ø 75, Ø 78mm hub/bearing
Additional set for Ø 72, Ø 75, Ø 78mm hub/bearing installation.
INSTALLATION
BEARINGS
BRAND
Ø 72
Audi, Seat
Ø 75
Mitsubishi, Smart
Ø 78
Ford, Volvo
REMOVAL
Tool set for Ø 72, Ø 75, Ø 78mm hub/bearing
INSTALLATION
323 039 000
11
Via degli Orsi, n. 97
40014 Loc. Beni Comunali | Crevalcore (BO) Italy
Tel: +39.051.982688 | Tel: +39.051.980798
Fax: +39.051.6801371
www.govoni.it | [email protected]

new products 2015

Transcription

Similar documents

speed bike indoor cycling

Engineering Solutions Partner. Camshaft Bearing - Dura-Bond

How To Install Cam Bearings - Dura-Bond

Where you come to know.

Euro-Diagnostic Resources, Inc. Euro Auto Training

33 Series Sweeperweb

Frigi-Tech - EnergyLogix Solutions Inc.

Pre-Owned Vehicle Protection

Crank Rebuild Manual

Lightweight Air Bearings