submersible electric water pumps for domestic and industrial use
Transcription
submersible electric water pumps for domestic and industrial use
SUBMERSIBLE ELECTRIC WATER PUMPS FOR DOMESTIC AND INDUSTRIAL USE City Pumps s.r.l. Via Enrico Fermi, 27 - P.O. BOX 84 37047 San Bonifacio (Verona) Italy Tel. (+39) 045 6102379 Fax (+39) 045 7614264 e-mail: [email protected] www.citypumps.com Introduction Co m pa ny p rof i le CITY PUMPS is the latest breakthrough from INOX POMPE. The company has undergone a restyling with a European brand image and an international repute in the manufacture of electric water pumps for civilian, agricultural and industrial applications. The productive standards implement all the electric and hydraulic inspections prescribed by the EU safety regulations and use productive plants that are among the technologically most advanced in the electro technical and mechanical industry. We export to over 50 countries. CITY PUMPS works in conjunction with leading international groups in the research and production of civilian and industrial electric water pumps. a wide range of... Performances of City Pumps’ submersible range of water pumps City Pumps offers a wide range of electric water pumps for domestic, civilian and industrial applications. Its range of products meets the requirements of an efficient product, simple to use, flexible and with low power consumption. Page Flow rate up to 100 l/min (6 m3/h) Head up to 42 m They are recommended for pumping clean water with a sand content no higher than 50 g/m3. Their high efficiency and reliability makes them suitable for supplying domestic water from tanks, reservoirs or relatively deep wells, drawing rainwater from cisterns, watering by hand or feeding. Page 10 SPEED Products Flow rate up to 400 l/min (24 m3/h) Head up to 14.5 m The SPEED series is suitable for draining clear water without abrasive particles. The construction guarantees simple and safe operation due to the complete cooling of the motor by the pumped water and the double seal design. They are recommended for emergency draining of small flooded areas (rooms, cellars, garages), for the disposal of waste water in the home (dishwasher, washing machine) and for emptying drainage traps. Page 12 Flow rate up to 220 l/min (13.2 m3/h) Head up to 9 m The SPEED MOP series is suitable for draining clear water without abrasive particles. Their ability to drain water down to 2 millimetres from the floor makes them ideal for emergency domestic use of small flooded areas and in all those applications where maximum drainage is required. Page 14 Flow rate up to 180 l/min (10.8 m3/h) Head up to 7 m The SPEED VORTEX pump is suitable for draining dirty water that is chemically non aggressive. The construction guarantees simple and safe operation due to the complete cooling of the motor by the pumped water and the double seal design. It is recommended for domestic use, for the clearing of dirty water, for emptying tanks, domestic drains and collection traps, even with suspended solid bodies with dimensions up to ø 20 mm. Page 16 Flow rate up to 300 l/min (18 m3/h) Head up to 23 m F1 pumps are suitable for draining clear water without abrasive particles. The construction guarantees simple and safe operation due to the complete cooling of the motor by the pumped water, and the double seal design. They are recommended for fixed installations, emergency draining of small flooded areas (basement rooms, cellars, garages), for disposal of dirty water used in the home by washing machines and dishwashers and for draining collection traps. Page 18 F1 SPEED VORTEX SPEED PLURI Applications SPEED MOP ...electric water pumps... Range of performance Page F1 VORTEX Flow rate up to 450 l/min (27 m3/h) Head up to 14.5 m F1 VORTEX pumps are suitable for draining dirty water. The construction guarantees simple and safe operation, due to the complete cooling of the motor by the pumped water. They are recommended for domestic use, for draining dirty water containing suspended solids. Page 20 DRENO Products Flow rate up to 300 l/min (18 m3/h) Head up to 14 m Designed for draining clear or slightly dirty water, they are suitable for domestic use, for draining flooded areas such as cellars and for emptying tanks and reservoirs; they are outstanding in both their simplicity of installation and their reliability in fixed installations with automatic operation. Page 22 Flow rate up to 300 l/min (18 m3/h) Head up to 10 m COBRA pumps are recommended for draining waste water in the domestic sector, for clearing dirty water, even containing suspended solid bodies with dimensions up to ø 40 mm. They are outstanding in both their simplicity of installation and their reliability in fixed installations with automatic operation. Page 24 Flow rate up to 400 l/min (24 m3/h) Head up to 27 m Designed for draining clear or slightly dirty water with small solids, they are recommended for domestic, civil and professional use, for draining flooded areas such as cellars and garages or for emptying swimming pools or tanks and for disposing of non-sewage waste water. These pumps are outstanding in their reliability in fixed installations with automatic operation. Page 26 Flow rate up to 500 l/min (30 m3/h) Head up to 15 m They are recommended for domestic, civil and industrial use, in applications where the water contains suspended solids with dimensions up to ø 50 mm. Their use is recommended for drying flooded areas such as cellars, underground car parks, car washing areas, or domestic drains and for emptying cesspits or sewage disposal. These pumps are outstanding in their reliability in fixed installations with automatic operation. Page 28 RANGER SECURITY Applications COBRA ...for any requirement Range of performance a complete line of electric water pumps... Range of performance Flow rate up to 800 l/min (48 m3/h) Head up to 15 m RANGER MC submersible pumps are recommended for draining dirty water and sewage in the domestic and civil sectors. They are equipped with a DOUBLE-CHANNEL stainless steel impeller which allows the pumping of liquids containing suspended solid bodies with dimensions up to ø 50 mm and short fibres. They are ideal for pumping drainage water, sewage or waste water for a single dwelling, and for clearing suface or nuisance water, even if muddy. These pumps are outstanding in their reliability in fixed installations with automatic operation. Page 30 Page 32 RANGER MC SS They are recommended for draining waste water in the domestic, civil and industrial sectors, in applications where the water contains suspended solids with dimensions up to ø 50 mm. Their use is recommended for drying flooded areas such as cellars, underground car parks, car washing areas and for emptying cesspits or sewage disposal. These pumps are outstanding in their reliability in fixed installations with automatic operation. Page Flow rate up to 800 l/min (48 m3/h) Head up to 15 m RANGER MC SS submersible pumps are recommended for draining dirty water and sewage in the domestic and civil sectors. They are equipped with a DOUBLE-CHANNEL stainless steel impeller which allows the pumping of liquids containing suspended solid bodies with dimensions up to ø 50 mm and short fibres. They are ideal for pumping drainage water, sewage or waste water for a single dwelling, and for clearing surface or nuisance water, even if muddy. These pumps are outstanding in their reliability in fixed installations with automatic operation. Page 34 SECURITY G Flow rate up to 400 l/min (24 m3/h) Head up to 10 m Applications Flow rate up to 400 l/min (24 m3/h) Head up to 27 m SECURITY G submersible pumps, made of exceptionally sturdy heavy-gauge cast iron, resistant to abrasion and long-lasting, are recommended for draining clear or slightly dirty water and for disposing of non-sewage waste water; they are outstanding both in their sturdiness and their reliability in fixed installations with automatic operation. Page 36 TITAN 35-45 RANGER SS RANGER MC Products Flow rate up to 500 l/min (30 m3/h) Head up to 15 m The pumps in the TITAN series are made of exceptionally robust heavygauge cast iron, resistant to abrasion and are equipped with a vortex type impeller. They are recommended for draining waste water containing suspended solid bodies, sewage and water mixed with mud. Page 38 Page PATROL 45 Flow rate up to 800 l/min (48 m3/h) Head up to 15 m The pumps in the PATROL series are made of exceptionally robust heavygauge cast iron, resistant to abrasion and long-lasting. They are equipped with a double-channel impeller which allows the drainage of liquids containing suspended solid bodies with dimensions up to ø 45 mm and short fibres. They are ideal for pumping drainage water and sewage, waste water including water mixed with mud, groundwater and surface water in applications such as: condominiums, multi-storey and underground car parks, washing areas and industry. Page 40 TITAN 50-70 Flow rate up to 1200 l/min (72 m3/h) Head up to 16 m TITAN series pumps are made of exceptionally robust heavy-gauge cast iron, resistant to abrasion and long-lasting, and have a vortex type impeller. They are suitable for sewage, waste water and sludge, including water containing solids or mud. They are ideal for sewage installation, tunnels and other excavations, underground car parks and similar applications. Page 42 PATROL 50-70 Products Flow rate up to 1600 l/min (96 m3/h) Head up to 24 m PATROL series pumps are made of exceptionally robust heavy gauge cast iron, abrasion resistant and long-lasting, with a single-channel impeller which can handle liquids with suspended solids and short fibres. They are ideal for sewage, waste and ground water, even with solids or mud, and are therefore recommended for building or industrial effluent and drainage of large areas such as car parks. Page 44 Flow rate up to 1200 l/min (72 m3/h) Head up to 16 m TITAN P series pumps are made of exceptionally robust heavy gauge cast iron, resistant to abrasion and long lasting, and have a vortex type impeller. They are suitable for sewage, waste water and sludge, including water containing solids or mud. They are ideal for fixed sewage installations, tunnels, underground carparks, sumps and similar applications. Page 46 Flow rate up to 1600 l/min (96 m3/h) Head up to 24 m PATROL P series pumps are made of exceptionally robust heavy gauge cast iron, abrasion resistant and long-lasting, with a single-channel impeller which can handle liquids with suspended solids and short fibres. They are ideal for sewage, waste and ground water, even with solids or mud, and are therefore recommended for building or industrial effluent and drainage of large areas such as car parks. Page 48 PATROL P Applications TITAN P ...to satisfy any requirement Range of performance 10 SPEED PLURI multi-stage submerged pumps SPEED PLURI 70H SPEED PLURI 50 H (m) SPEED PLURI 70 Q Q = Flow rate H = Total manometric head TYPE POWER Single-phase kW HP SPEED PLURI 50M 0.37 0.50 SPEED PLURI 70M 0.55 0.75 SPEED PLURI 70HM 0.55 0.75 m3/h l/min H metres Tolerance of the performance curves according to EN ISO 9906 App. A. 0 0.6 1.2 1.8 2.4 3.0 3.6 4.2 4.8 5.4 6.0 0 10 20 30 40 50 60 70 80 90 100 36 33 30.5 26.5 21.5 14.5 5 30 29 28 27 26 24 22 19 15 10.5 5 42 38 35 31 25 17.5 8 DIMENSIONS AND WEIGHTS TYPE PORT Single-phase DN SPEED PLURI 50M SPEED PLURI 70M SPEED PLURI 70HM DIMENSIONS N° stages a 6 11/4” 5 7 176 h h1 380 345 400 365 kg d e p 30 adjustable 350 8.4 350 8.1 8.9 11 RANGE OF PERFORMANCE Flow rate up to 100 l/min (6 m3/h) Head up to 42 m CONSTRUCTION CHARACTERISTICS • DELIVERY BODY AND SUCTION GRID: glass filled technopolymer, particularly resistant to impact and corrosion, with threaded port ISO 228/1. • IMPELLERS and DIFFUSERS: technopolymer. • DIFFUSER CONTAINER: stainless steel AISI 304. • MOTOR SUPPORT: stainless steel AISI 304. • MOTOR SHAFT: stainless steel EN 10088-3 - 1.4104. • DOUBLE SEAL: mechanical seal ceramic -silicon carbideNBR, with oil barrier chamber and inner lip seal to protect the seal in the event of dry running. •MOTOR: asynchronous, for continuous duty. SPEED PLURI M: single-phase 220÷240 V - 50 Hz with capacitor and thermal overload protector. •INSULATION: class F. •PROTECTION: IP 68. LIMITS OF USE Submersion depth up to 10 m Liquid temperature up to + 40°C Maximum sand content 50 g/m3 Emptying level up to 30 mm from the bottom INSTALLATION AND USE THEY ARE RECOMMENDED FOR pUMPING CLEAN WATER WITH A SAND CONTENT NO HIGHER THAN 50 g/m3. THEIR HIGH EFFICIENCY AND RELIABILITY MAKES THEM SUITABLE FOR SUPPLYING DOMESTIC WATER FROM TANKS, RESERVOIRS OR RELATIVELY DEEP WELLS, DRAWING RAINWATER FROM CISTERNS, WATERING BY HAND OR FEEDING. STANDARD FEATURES: •Float switch Neoprene power cable “H05 RN-F” •length 10 metres with Schuko plug •Hosetail. •Coupling with non-return valve. GUARANTEE 2 YEARS subject to our general terms of sale. OPTIONS ON REQUEST ⇒other voltages or frequency 60 Hz CONSTRUCTION AND SAFETY STANDARDS EN 60 335-1 EN 60034-1 IEC 335-1 IEC 34-1 CEI 61-150 CEI 2-3 DIMENSIONS Typical portable application e d a p minimum h1 h DN minimum 12 SPEED DRAINAGE submersible pumps SPEED 125 SPEED 100 SPEED 70 H (m) SPEED 50 SPEED 30 Q Q = Flow rate H = Total manometric head TYPE Single-phase POWER kW HP m3/h l/min Tolerance of the performance curves according to EN ISO 9906 App. A. 0 0 1.2 20 2.4 40 3.6 60 4.8 80 6.0 100 7.2 120 8.4 140 9.6 10.8 12 13.2 14.4 15.6 16.8 18.0 19.2 20.4 21.6 22.8 24 160 180 200 220 240 260 280 300 320 340 360 380 400 SPEED 30M 0.25 0.33 7 6 5.5 4.5 4 3 2.5 1.5 1 SPEED 50M 0.37 0.50 9 8 7.5 6.5 6 5.5 4.5 4 3 2.5 1.8 1 SPEED 70M 0.55 0.75 H metres 10.5 10 9 8.8 8 7.5 6.5 6 5.5 4.8 4 3.5 2.5 2 SPEED 100M 0.75 1 12.6 12 11.5 10.7 10 9.3 8.7 8 7.3 6.7 6 5.3 4.7 4 3.3 2.7 2 SPEED 125M 0.92 1.25 14.5 14 13.5 12.7 12.1 11.5 10.8 10.2 9.6 8.9 8.3 7.7 7.1 6.4 5.8 5.2 4.5 3.9 3.3 2.6 DIMENSIONS AND WEIGHTS TYPE PORT Single-phase DN SPEED 30M 1” SPEED 50M SPEED 70M SPEED 100M SPEED 125M 11/4” 11/2” DIMENSIONS mm a h 232 217 152 257 237 287 267 334 310 204 h1 d kg e p 4.1 14 350 350 adjustable 21 5.0 6.4 450 450 9.8 10.8 2 13 RANGE OF PERFORMANCE Flow rate up to 400 l/min (24 m3/h) Head up to 14.5 m LIMITS OF USE Depth up to 5 metres (3 metres up to 0.55 kW) Liquid temperature up to + 40°C (+90°C for a maximum period of 3 minutes) Passage of solid bodies up to Ø 10 mm Drainage level: 14 mm from the bottom for SPEED 30-50-70M 30 mm from the bottom for SPEED 100-125M INSTALLATION AND USE THE SPEED SERIES IS SUITABLE FOR DRAINING CLEAR WATER WITHOUT ABRASIVE PARTICLES. THE CONSTRUCTION GUARANTEES SIMPLE AND SAFE OPERATION DUE TO THE COMPLETE COOLING OF THE MOTOR BY THE PUMPED WATER AND THE DOUBLE SEAL DESIGN. THEY ARE RECOMMENDED FOR EMERGENCY DRAINING OF SMALL FLOODED AREAS (ROOMS, CELLARS, GARAGES), FOR THE DISPOSAL OF WASTE WATER IN THE HOME (DISHWASHER, WASHING MACHINE) AND FOR EMPTYING DRAINAGE TRAPS. particularly resistant to impact and corrosion, with threaded port ISO 228/1. • SUCTION GRID: technopolymer. • IMPELLER: open type in technopolymer. • MOTOR SUPPORT: stainless steel AISI 304. • MOTOR SHAFT: stainless steel EN 10088-3 - 1.4104. • DOUBLE SEAL: mechanical seal ceramic -graphite - NBR, with oil barrier chamber and inner lip seal to protect the seal in the event of dry running. • MOTOR: submersible asynchronous single-phase for continuous duty. SPEED M: single-phase 220÷240 V - 50 Hz with capacitor and thermal overload protector built into the winding. • INSULATION: class F. • PROTECTION: IP 68. STANDARD FEATURES: SPEED 30-50-70 M(single-phase) • Float switch. • Hosetail. • Power cable in neoprene “H05RN-F” length 5 metres with Schuko plug. GUARANTEE 2 YEARS subject to our general terms of sale. SPEED 100-125 M (single-phase) • Float switch. •Hosetail. •Coupling with flap valve. •Neoprene power cable “H05 RN-F” length 10 metres with Schuko plug. CONSTRUCTION CHARACTERISTICS • DELIVERY BODY: glass filled technopolymer, OPTIONS ON REQUEST ⇒pumps for aggressive liquids SPEED - AF ⇒special mechanical seal ⇒10 metres power cable. N.B. required for outdoor use to comply with standard EN 60335-2-41 ⇒versions without float switch ⇒other voltages or frequency 60 Hz CONSTRUCTION AND SAFETY STANDARDS EN 60 335-1 EN 60034-1 IEC 335-1 IEC 34-1 CEI 61-150 CEI 2-3 DIMENSIONS Typical portable application SPEED-AF* for aggressive liquids DN TYPE Single-phase SPEED 30M - AF SPEED 50M - AF ® SPEED 100M - AF SPEED 125M - AF d * Wetted metal parts in AISI 316 stainless steel. e h1 h SPEED 70M - AF p minimum ® a ® ® minimum 14 SPEED MOP DRAINAGE submersible pumps SPEED MOP 50 H (m) SPEED MOP 30 Q Q = Flow rate H = Total manometric head TYPE Single-phase SPEED MOP 30M SPEED MOP 50M POWER m3/h l/min kW HP 0.25 0.33 H metres 0.37 0.50 Tolerance of the performance curves according to EN ISO 9906 App. A. 0 0 7 9 1.2 20 6 8 2.4 40 5.5 7.5 3.6 60 4.5 6.5 4.8 80 4 6 6.0 100 3 5.5 7.2 120 2.5 4.5 8.4 140 1.5 4 9.6 160 1 3 10.8 180 12.0 200 13.2 220 2.5 1.8 1 DIMENSIONS AND WEIGHTS TYPE PORT Single-phase DN SPEED MOP 30M 1” SPEED MOP 50M 11/4” DIMENSIONS mm a 152 h h1 232 217 257 237 Minimum drying level 2 mm kg 3.9 4.9 15 RANGE OF PERFORMANCE Flow rate up to 220 l/min (13.2 m3/h) Head up to 9 m particularly resistant to impact and corrosion, with threaded port ISO 228/1. • SUCTION GRID: technopolymer. • IMPELLER: open type in technopolymer. • MOTOR SUPPORT: stainless steel AISI 304. • MOTOR SHAFT: stainless steel EN 10088-3 - 1.4104. • DOUBLE SEAL: mechanical seal ceramic - graphite - NBR, with oil barrier chamber and inner lip seal to protect the seal in the event of dry running. • MOTOR: submersible asynchronous single-phase for continuous duty. SPEED MOP: single-phase 220÷240 V-50 Hz with capacitor and thermal overload protector. •INSULATION: class F. •PROTECTION: IP 68. LIMITS OF USE Depth up to 3 m Liquid temperature up to +40°C (+90° C for a maximum period of 3 minutes) Passage of solid bodies up to Ø 5 mm Drainage level 2 mm from the bottom INSTALLATION AND USE THE SPEED MOP SERIES IS SUITABLE FOR DRAINING CLEAR WATER WITHOUT ABRASIVE PARTICLES. THEIR ABILITY TO DRAIN WATER DOWN TO 2 MILLIMETRES FROM THE FLOOR MAKES THEM IDEAL FOR EMERGENCY DOMESTIC USE FOR SMALL FLOODED AREAS AND IN ALL THOSE APPLICATIONS WHERE MAXIMUM DRAINAGE IS REQUIRED. STANDARD FEATURES: •Neoprene power cable “H05 RN-F” •length 5 metres with Schuko plug. •Hosetail. GUARANTEE 2 YEARS subject to our general terms of sale. OPTIONS ON REQUEST ⇒versions with external float switch ⇒special mechanical seal ⇒10 metres power cable. N.B. required for outdoor CONSTRUCTION CHARACTERISTICS • DELIVERY BODY: glass filled technopolymer, use to comply with standard EN 60335-2-41 ⇒other voltages or frequency 60 Hz CONSTRUCTION AND SAFETY STANDARDS EN 60 335-1 EN 60034-1 IEC 335-1 IEC 34-1 CEI 61-150 CEI 2-3 DIMENSIONS Typical portable application DN Draining down to 2 mm ® h1 h ® ® ® a 16 SPEED VORTEX VORTEX submersible pump H (m) SPEED VORTEX 50 Q Q = Flow rate H = Total manometric head TYPE Single-phase SPEED VORTEX 50M POWER kW HP 0.37 m3/h l/min 0.50 H metres Tolerance of the performance curves according to EN ISO 9906 App. A. 0 0 1.2 20 2.4 40 3.6 60 4.8 80 6.0 100 7.2 120 8.4 140 9.6 160 10.8 180 7 6.5 6 5.4 4.8 4.2 3.5 3 2.5 1.5 DIMENSIONS AND WEIGHTS TYPE PORT Single-phase DN SPEED VORTEX 50M 11/4” DIMENSIONS mm kg a h h1 d e p 152 288 268 25 adjustable 350 350 5.0 17 RANGE OF PERFORMANCE Flow rate up to 180 l/min (10.8 m3/h) Head up to 7 m LIMITS OF USE Depth up to 3 m Liquid temperature up to + 40°C (+90° C for a maximum period of 3 minutes) Passage of solid bodies up to Ø 20 mm Drainage level 25 mm from the bottom INSTALLATION AND USE THESPEED VORTEX PUMP IS SUITABLE FOR DRAINING DIRTY WATER THAT IS CHEMICALLY NON AGGRESSIVE. THE CONSTRUCTION GUARANTEES SIMPLE AND SAFE OPERATION DUE TO THE COMPLETE COOLING OF THE MOTOR BY THE PUMPED WATER AND THE DOUBLE SEAL DESIGN. IT IS RECOMMENDED FOR DOMESTIC USE, FOR THE CLEARING OF DIRTY WATER, FOR EMPTYING TANKS, DOMESTIC DRAINS AND COLLECTION TRAPS, EVEN WITH SUSPENDED SOLID BODIES WITH DIMENSIONS UP TO Ø 20 mm. GUARANTEE 2 YEARS: subject to our general terms of sale. CONSTRUCTION CHARACTERISTICS • DELIVERY BODY: glass filled technopolymer, particularly resistant to impact and corrosion, with threaded port ISO 228/1. • SUCTION GRID: technopolymer. • IMPELLER: technopolymer. • MOTOR SUPPORT: stainless steel AISI 304. • MOTOR SHAFT: stainless steel EN 10088-3 - 1.4104. • DOUBLE SEAL: mechanical seal ceramic - graphite - NBR, with oil barrier chamber and inner lip seal to protect the seal in the event of dry running. • MOTOR: submersible asynchronous single-phase for continuous duty. SPEED VORTEX 50M: single-phase 220÷240 V - 50 Hz with capacitor and thermal overload protector. •INSULATION: class F. •PROTECTION: IP 68. OPTIONS ON REQUEST ⇒special mechanical seal ⇒10 metres power cable. N.B. required for outdoor use to comply with standard EN 60335-2-41 ⇒other voltages or frequency 60 Hz STANDARD FEATURES: • Float switch. • Hosetail. • Neoprene power cable “H05 RN-F” • length 5 metres with Schuko plug. CONSTRUCTION AND SAFETY STANDARDS EN 60 335-1 EN 60034-1 IEC 335-1 IEC 34-1 CEI 61-150 CEI 2-3 DIMENSIONS Typical installation DN ® e ® d p minimum ® h1 h ® a minimum 18 F1 DRAINAGE submersible pumps F1/150 F1/100 H (m) F1/70 F1/50 F1/30 Q Q = Flow rate H = Total manometric head TYPE Single-phase F1/30M F1/50M F1/70M F1/100M F1/150M Three-phase F1/50 F1/70 F1/100 F1/150 Tolerance of the performance curves according to EN ISO 9906 App. A. POWER 0 m3/h l/min kW HP 0 0.25 0.33 7.5 0.37 0.50 10 0.55 0.75 H metres 17 0.75 1 20 1.1 1.5 23 1.2 20 6.5 9.5 16 19 22 2.4 40 5.8 8.8 15 18 21 3.6 60 5 8 13.8 16.8 20 4.8 80 4.3 7.3 12.8 15.8 18.8 6.0 100 3.5 6.5 11.7 14.7 17.7 7.2 120 2.8 5.8 10.5 13.5 16.5 8.4 140 2 5 9.5 12.5 15.5 9.6 160 10.8 180 12.0 200 13.2 220 14.4 240 15.6 260 16.8 280 18.0 300 4.3 8.5 11.5 14.5 3.5 7.3 10.5 13.5 2.8 6.3 9.3 12.4 2 5.2 8.2 11.3 4 7.2 10.2 3 6 9 5 8 7 DIMENSIONS AND WEIGHTS TYPE Single-phase PORT Three-phase F1/30M - F1/50M F1/50 F1/70M F1/70 F1/100M F1/100 F1/150M F1/150 DN 11/4” DIMENSIONS mm a 147 h 255 h1 247 d kg e 17 p 350 1~ 350 adjustable 11/2” 215 355 336 30 500 500 3~ 4.7 - 5.7 5.5 12.0 10.7 13.0 11.7 14.0 12.7 19 RANGE OF PERFORMANCE Flow rate up to 300 l/min (18 m3/h) Head up to 23 m LIMITS OF USE Depth up to 10 m Liquid temperature up to + 50°C Liquid temperature up to + 60°C for intermittent duty. Liquid temperature up to + 90°C for intermittent duty maximum 3 minutes. Passage of solid bodies up to Ø 10 mm Drainage level: 14 mm from the bottom for F1 1-2 30 mm from the bottom for F1 3-4-5 INSTALLATION AND USE F1 PUMPS ARE SUITABLE FOR DRAINING CLEAR WATER WITHOUT ABRASIVE PARTICLES. THE CONSTRUCTION GUARANTEES SIMPLE AND SAFE OPERATION DUE TO THE COMPLETE COOLING OF THE MOTOR BY THE PUMPED WATER, AND THE DOUBLE SEAL DESIGN. THEY ARE RECOMMENDED FOR FIXED INSTALLATIONS, EMERGENCY DRAINING OF SMALL FLOODED AREAS (BASEMENT ROOMS, CELLARS, GARAGES), FOR DISPOSAL OF DIRTY WATER USED IN THE HOME BY WASHING MACHINES AND DISHWASHERS AND FOR DRAINING COLLECTION TRAPS. GUARANTEE 2 YEARS subject to our general terms of sale. CONSTRUCTION CHARACTERISTICS • DELIVERY BODY: stainless steel AISI 304, with threaded port ISO 228/1. • SUCTION GRID: stainless steel AISI 304. • IMPELLER: stainless steel AISI 304. • MOTOR SUPPORT: stainless steel AISI 304. • MOTOR SHAFT: stainless steel EN 10088-3 - 1.4104. • DOUBLE SEAL: mechanical seal ceramic - graphite - NBR, with oil barrier chamber and inner lip seal to protect the seal in the event of dry running. • MOTOR: submersible asynchronous single-phase for continuous duty. F1 M: single-phase 220÷240 V - 50 Hz with capacitor and thermal overload protector. F1: three-phase 380÷415 V - 50 Hz. •INSULATION: class F. • PROTECTION: IP 68. STANDARD FEATURES: F1 M (single-phase) •float switch. •Neoprene power cable “H05 RN-F” •length 5 metres with Schuko plug. F1 (three-phase) •Neoprene power cable “H05 RN-F” length 5 metres. OPTIONS ON REQUEST ⇒special mechanical seal ⇒10 metres power cable. N.B. required for outdoor use to comply with standard EN 60335-2-41 ⇒control box for three-phase electropumps 1.1 kW ⇒single-phase versions without float switch ⇒other voltages or frequency 60 Hz CONSTRUCTION AND SAFETY STANDARDS EN 60 335-1 EN 60034-1 IEC 335-1 IEC 34-1 CEI 61-150 CEI 2-3 DIMENSIONS Typical single-phase installation d e p minimum h1 h DN a minimum 20 F1 VORTEX VORTEX submersible pumps F1/150 VORTEX F1/100 VORTEX H (m) F1/70 VORTEX F1/50 VORTEX Q Q = Flow rate H = Total manometric head TYPE Single-phase Three-phase F1/50M VORTEX F1/50 VORTEX F1/70M VORTEX F1/70 VORTEX F1/100M VORTEX F1/100 VORTEX F1/150M VORTEX F1/150 VORTEX Tolerance of the performance curves according to EN ISO 9906 App. A. POWER 0 m3/h l/min kW HP 0 0.37 0.50 7 0.55 0.75 9 H metres 0.75 1 11 1.1 1.5 15 1.2 20 6.5 8.5 10.5 14.5 2.4 40 6 8 10 14 3.6 60 5.4 7.4 9.4 13.3 4.8 80 4.8 6.8 8.8 12.8 6 100 4.3 6.3 8.3 12.2 7.2 120 3.7 5.7 7.7 11.6 8.4 140 3.1 5.1 7.1 11 9.6 160 2.5 4.5 6.6 10.4 10.8 180 2 4 6 9.8 12 200 15 250 18 300 19.5 325 21 350 24 400 27 450 3.4 5.5 9.2 2 4 7.8 2.7 6.3 2 5.6 4.9 3.5 2 DIMENSIONS AND WEIGHTS TYPE Single-phase PORT Three-phase F1/50M VORTEX F1/50 VORTEX F1/70M VORTEX F1/70 VORTEX F1/100M VORTEX F1/100 VORTEX F1/150M VORTEX F1/150 VORTEX DIMENSIONS mm DN a h h1 d 11/4” 147 286 278 25 11/2” 215 405 386 40 kg e p 350 adjustable 500 1~ 350 500 3~ 5.9 5.7 12.4 11.1 13.4 12.1 14.4 13.1 21 RANGE OF PERFORMANCE Flow rate up to 450 l/min (27 m3/h) Head up to 14.5 m LIMITS OF USE Depth up to 10 m Liquid temperature up to + 50°C Liquid temperature up to + 60°C for intermittent duty. Liquid temperature up to + 90°C for intermittent duty maximum 3 minutes. Passage of solid bodies: up to 20 mm for F1/50 - up to 40 mm for F1/70-100-150 Drainage level from the bottom: 25 mm for F1/50 - 40 mm for F1/70-100-150 INSTALLATION AND USE F1 VORTEX PUMPS ARE SUITABLE FOR DRAINING DIRTY WATER. THE CONSTRUCTION GUARANTEES SIMPLE AND SAFE OPERATION, DUE TO THE COMPLETE COOLING OF THE MOTOR BY THE PUMPED WATER. THEY ARE RECOMMENDED FOR DOMESTIC USE, FOR DRAINING DIRTY WATER CONTAINING SUSPENDED SOLIDS. GUARANTEE 2 YEARS subject to our general terms of sale. CONSTRUCTION CHARACTERISTICS • DELIVERY BODY: stainless steel AISI 304, with threaded port ISO 228/1. • SUCTION GRID: stainless steel AISI 304. • IMPELLER: stainless steel AISI 304. • MOTOR SUPPORT: stainless steel AISI 304. • MOTOR SHAFT: stainless steel EN 10088-3 - 1.4104. • DOUBLE SEAL: mechanical seal silicon carbide - NBR, with oil barrier chamber and inner lip seal to protect the seal in the event of dry running. • MOTOR: submersible asynchronous single-phase for continuous duty. F1 M VORTEX: single-phase 220÷240 V - 50 Hz with capacitor and thermal overload protector. F1 VORTEX: three-phase380÷415 V - 50 Hz. •INSULATION: class F. • PROTECTION: IP 68. STANDARD FEATURES: F1 M VORTEX (single-phase) •Float switch. •Neoprene power cable “H05 RN-F” •Length 5 metres with Schuko plug. F1 VORTEX (three-phase) •Neoprene power cable “H05 RN-F” •Length 5 metres. N.B. required for outdoor use to comply with standard EN 60335-2-41 ⇒control box for three-phase pumps 1.1 kW ⇒single-phase versions without float switch ⇒other voltages or frequency 60 Hz CONSTRUCTION AND SAFETY STANDARDS EN 60 335-1 EN 60034-1 IEC 335-1 IEC 34-1 CEI 61-150 CEI 2-3 OPTIONS ON REQUEST ⇒special mechanical seal ⇒10 metres power cable. DIMENSIONS Typical single-phase installation e d p minimum h1 h DN a minimum 22 DRENO DRAINAGE submersible pumps 10 0 15 14 20 30 10 0 40 20 50 30 60 40 70 50 US g.p.m. 60 Imp. g.p.m. feet 45 DRENO 90 13 40 12 11 35 DRENO 80 10 30 9 DRENO 60 H (m) 8 25 7 20 6 5 15 4 10 3 2 5 1 0 0 25 50 75 0 100 125 150 5 175 200 225 250 10 275 300 0 l/min m3/h 15 Q Q = Flow rate H = Total manometric head TYPE Single-phase DRENO 60M DRENO 80M DRENO 90M Tolerance of the performance curves according to EN ISO 9906 App. A. POWER m3/h l/min kW HP 0.37 0.50 0.50 0.70 H metres 0.60 0.85 0 0 8.5 11 14 1.5 25 8 10.5 13.5 3.0 50 7.5 10 13 4.5 75 6.5 9 12.2 6.0 100 5.5 8.5 11.5 7.5 125 4.8 7.5 10.5 9.0 150 3.5 6.5 9.5 10.5 175 2.5 5.5 8.3 12.0 200 1 4 7 13.5 225 15.0 250 16.5 275 18.0 300 2.5 5.7 1.5 4.5 3.2 2 DIMENSIONS AND WEIGHTS TYPE PORT Single-phase DN a b c h DIMENSIONS mm h1 d e p kg 11/2” 110 81 142 310 66 15 adjustable 450 DRENO 60M DRENO 80M DRENO 90M 9.8 450 10.4 11.3 23 RANGE OF PERFORMANCE Flow rate up to 300 l/min (18 m3/h) Head up to 14 m CONSTRUCTION CHARACTERISTICS • DELIVERY BODY: cast iron, with threaded port ISO 228/1. • MOTOR CASING: stainless steel AISI 304. • SUCTION GRID: stainless steel AISI 304. • IMPELLER: open type, in technopolymer. • MOTOR SHAFT: stainless steel EN 10088-3 - 1.4104. • MECHANICAL SEAL: ceramic - graphite - NBR. • MOTOR: submersible asynchronous single-phase for continuous duty. DRENO M: single-phase 220÷240 V - 50 Hz with capacitor and thermal overload protector. •INSULATION: class F. •PROTECTION: IP 68. LIMITS OF USE Depth up to 5 m Liquid temperature up to + 40°C Passage of suspended solid bodies up to Ø 10 mm Drainage level 15 mm from the bottom For continuous duty: minimum immersion 180 mm from pump base INSTALLATION AND USE DESIGNED FOR DRAINING CLEAR OR SLIGHTLY DIRTY WATER, THEY ARE SUITABLE FOR domestic USE, FOR DRAINING FLOODED AREAS SUCH AS CELLARS AND FOR EMPTYING TANKS AND RESERVOIRS; THEY ARE OUTSTANDING IN BOTH THEIR SIMPLICITY OF installaTion AND THEIR RELIABILITY IN FIXED installaTionS WITH automatic oPERATION. STANDARD FEATURES: •Float switch. •Neoprene power cable “H07 RN-F” •length 5 metres with Schuko plug. OPTIONS ON REQUEST ⇒special mechanical seal ⇒10 metres power cable. N.B. required for outdoor use to comply with standard EN 60335-2-41 ⇒versions without float switch ⇒other voltages or frequency 60 Hz GUARANTEE 2 YEARS subject to our general terms of sale. CONSTRUCTION AND SAFETY STANDARDS EN 60 335-1 EN 60034-1 IEC 335-1 IEC 34-1 CEI 61-150 CEI 2-3 DIMENSIONS Typical single-phase installation d h1 DN e h p minimum a b c minimum 24 COBRA VORTEX submersible pumps COBRA 90 H (m) COBRA 80 Q Q = Flow rate H = Total manometric head TYPE Single-phase COBRA 80M COBRA 90M Tolerance of the performance curves according to EN ISO 9906 App. A. POWER m3/h l/min kW HP 0.50 0.70 H metres 0.60 0.85 0 0 9 11 1.5 25 8.5 10.5 3.0 50 8.3 10 4.5 75 8 9.5 6.0 100 7.5 9.2 9.0 150 6.5 8.2 12.0 200 5.2 7 15.0 250 4 5.7 18.0 300 2.5 4.3 21.0 350 1 2.8 24.0 400 1.5 DIMENSIONS AND WEIGHTS TYPE PORT Single-phase DN passage of solid bodies a b c h h1 d e p 11/2” Ø 40 mm 110 93 150 372 128 40 adjustable 450 COBRA 80M COBRA 90M DIMENSIONS mm kg 450 10.8 12.4 25 RANGE OF PERFORMANCE Flow rate up to 300 l/min (18 m3/h) Head up to 10 m LIMITS OF USE Depth up to 5 m Liquid temperature up to + 40°C Passage of suspended solid bodies up to Ø 40 mm Drainage level 40 mm from the bottom For continuous duty: minimum immersion 240 mm from pump base INSTALLATION AND USE COBRA PUMPS ARE RECOMMENDED FOR DRAINING WASTE WATER IN THE DOMESTIC SECTOR, FOR CLEARING DIRTY WATER, EVEN CONTAINING SUSPENDED SOLID BODIES WITH DIMENSIONS UP TO Ø 40 mm. THEY ARE OUTSTANDING IN BOTH THEIR SIMPLICITY OF installaTion AND THEIR RELIABILITY IN FIXED installaTionS WITH automatic oPERATION. GUARANTEE 2 YEARS subject to our general terms of sale. CONSTRUCTION CHARACTERISTICS • DELIVERY BODY: cast iron, with threaded port ISO 228/1. • MOTOR CASING: stainless steel AISI 304. • IMPELLER: open type, in glass filled technopolymer. • MOTOR SHAFT: stainless steel EN 10088-3 - 1.4104. • MECHANICAL SEAL: ceramic - graphite - NBR. • MOTOR: submersible asynchronous single-phase for continuous duty. COBRA M: single-phase 220÷240 V - 50 Hz with capacitor and thermal overload protector. •INSULATION: class F. • PROTECTION: IP 68. STANDARD FEATURES: • Float switch. • Neoprene power cable “H07 RN-F” • length 5 metres with Schuko plug. OPTIONS ON REQUEST ⇒special mechanical seal 10 metres power cable. N.B. required for outdoor use to comply with standard EN 60335-2-41 ⇒versions without float switch ⇒other voltages or frequency 60 Hz CONSTRUCTION AND SAFETY STANDARDS EN 60 335-1 EN 60034-1 IEC 335-1 IEC 34-1 CEI 61-150 CEI 2-3 DIMENSIONS Typical installation b c e d h1 DN p minimum h a minimum 26 SECURITY DRAINAGE submersible pumps SECURITY 30 SECURITY 20 SECURITY 15 SECURITY 18 H (m) SECURITY 10 SECURITY 8 SECURITY 6 Q Q = Flow rate H = Total manometric head TYPE Single-phase SECURITY 6M SECURITY 8M SECURITY 10M SECURITY 15M SECURITY 18M SECURITY 20M SECURITY 30M Three-phase ––– ––– SECURITY 10 SECURITY 15 ––– SECURITY 20 SECURITY 30 Tolerance of the performance curves according to EN ISO 9906 App. A. POWER 0 m3/h l/min kW HP 0 0.45 0.60 9 0.60 0.85 12 0.75 1 15 1.1 1.5 H metres 19.5 0.6 0.85 17 0.75 1 21 1.1 1.5 27 1.5 25 8.5 11.5 14.5 19 16.5 20 26 3.0 50 8 11 14 18.5 15 19 25 4.5 75 7.5 10.5 13.2 18 13.5 17.5 23.5 6.0 100 6.8 9.8 12.5 17.5 12 16 22 7.5 125 6 9 11.8 16.5 10.7 15 21 9.0 150 5.2 8.2 11 16 9 13.5 19.5 10.5 175 4 7.2 10 15 7.7 12 18 12.0 200 2.6 6 9 14 5 10 16 13.5 225 1 4.8 8 13 15.0 250 16.5 275 18.0 300 19.5 325 21.0 350 24.0 400 3.5 6.8 11.8 2 5.4 10.5 3.5 9.2 2 8 7 4 14.5 13 11.5 10 DIMENSIONS AND WEIGHTS TYPE Single-phase PORT Three-phase SECURITY 6M ––– SECURITY 8M ––– SECURITY 10M SECURITY 10 SECURITY 15M SECURITY 15 SECURITY 18M ––– SECURITY 20M SECURITY 20 SECURITY 30M SECURITY 30 DN DIMENSIONS mm a 105 11/2” 110 b 81 90 c 136 140 h 320 340 h1 kg d e p 66 80 105 81 136 320 66 110 90 140 340 80 15 adjustable 500 500 1~ 3~ 10.6 - 11.9 - 13.0 11.9 15.2 14.1 12.0 - 13.0 11.9 15.2 14.1 27 RANGE OF PERFORMANCE Flow rate up to 400 l/min (24 m3/h) Head up to 27 m LIMITS OF USE Depth up to 5 m Liquid temperature up to + 40°C Passage of suspended solid bodies up to Ø 10 mm Drainage level 15 mm from the bottom For continuous duty: minimum immersion 220 mm from pump base INSTALLATION AND USE DESIGNED FOR DRAINING CLEAR OR SLIGHTLY DIRTY WATER WITH SMALL SOLIDS, THEY ARE RECOMMENDED FOR domestic, civiL AND professional USe, FOR DRAINING FLOODED AREAS SUCH AS CELLARS AND garageS oR FOR EMPTYING SWIMMING POOLS OR TANKS AND FOR DISPOSING OF NON-SEWAGE WASTE WATER. THESE PUMPS ARE OUTSTANDING IN THEIR RELIABILITY IN FIXED installaTionS WITH automatic oPERATION. GUARANTEE 2 YEARS subject to our general terms of sale. CONSTRUCTION CHARACTERISTICS • DELIVERY BODY: cast iron, with threaded port ISO 228/1. • MOTOR CASING: stainless steel AISI 304. • SUCTION GRID: stainless steel AISI 304. • IMPELLER: open type, in glass filled technopolymer • MOTOR SHAFT: stainless steel EN 10088-3 - 1.4104. • DOUBLE SEAL: mechanical seal silicon carbide -ceramic- NBR, with oil barrier chamber and inner lip seal to protect the seal in the event of dry running. • MOTOR: submersible asynchronous for continuous duty. SECURITY M: single-phase 220÷240 V - 50 Hz with capacitor and thermal overload protector. SECURITY: three-phase 380÷415 V - 50 Hz. •INSULATION: class F. • PROTECTION: IP 68. ⇒control box for three-phase pumps 1.1 kW ⇒single-phase pumps without float switch ⇒other voltages or frequency 60 Hz STANDARD FEATURES: SECURITY M (single-phase) • Float switch. • Neoprene power cable “H07 RN-F” length 5 metres with Schuko plug. SECURITY (three-phase) • Neoprene power cable “H07 RN-F” length 5 metres. CONSTRUCTION AND SAFETY STANDARDS EN 60 335-1 EN 60034-1 IEC 335-1 IEC 34-1 CEI 61-150 CEI 2-3 OPTIONS ON REQUEST ⇒10 metres power cable. N.B. required for outdoor use to comply with standard EN 60335-2-41 DIMENSIONS Typical single-phase installation d h1 DN e h p minimum a b c minimum 28 RANGER VORTEX submersible pumps RANGER 15/35 RANGER 15/50 H (m) RANGER 10/35 RANGER 8/35 RANGER 10/50 RANGER 8/50 Q Q = Flow rate H = Total manometric head TYPE Single-phase Three-phase RANGER 8/35M ––– RANGER 10/35M RANGER 10/35 RANGER 15/35M RANGER 15/35 RANGER 8/50M ––– RANGER 10/50M RANGER 10/50 RANGER 15/50M RANGER 15/50 Tolerance of the performance curves according to EN ISO 9906 App. A. POWER m3/h l/min kW HP 0.60 0.85 0.75 1 1.1 1.5 H metres 0.60 0.85 0.75 1 1.1 1.5 0 0 8.4 10 15 6 7.5 11 3 50 7.5 9.5 14 5.5 7 10.5 6 100 6.5 8.5 13 5 6.5 10 9 150 5.2 7.2 11.8 4.4 5.8 9.5 12 200 3.7 5.8 10.5 3.6 5 9 15 250 2 4 9 2.8 4 8.3 18 300 21 350 24 400 27 450 2 7.5 2 3.2 7.5 6 1 2.4 6.8 4 2 1.5 6 5 30 500 4 DIMENSIONS AND WEIGHTS TYPE Single-phase DN passage of solid bodies 11/2” Ø 35 mm PORT Three-phase RANGER 8/35M ––– RANGER 10/35M RANGER 10/35 RANGER 15/35M RANGER 15/35 RANGER 8/50M ––– RANGER 10/50M RANGER 10/50 RANGER 15/50M RANGER 15/50 DIMENSIONS mm b c h h1 d 105 87 137 380 123 40 92 143 400 133 110 2” kg a Ø 50 mm 120 90 150 410 153 97 163 430 158 55 65 e adjustable p 500 1~ 500 3~ 12.4 - 13.5 12.1 15.7 14.6 13.4 - 13.9 12.1 16.1 15.0 29 RANGE OF PERFORMANCE Flow rate up to 500 l/min (30 m3/h) Head up to 15 m CONSTRUCTION CHARACTERISTICS • DELIVERY BODY: cast iron, with threaded port ISO 228/1. • MOTOR CASING: stainless steel AISI 304. • BASE: stainless steel AISI 304. • IMPELLER: stainless steel AISI 304. • MOTOR SHAFT: stainless steel EN 10088-3 - 1.4104. • DOUBLE SEAL: mechanical seal silicon carbide-ceramic -NBR, with oil barrier chamber and inner lip seal to protect the seal in the event of dry running. • MOTOR: submersible asynchronous for continuous duty. RANGER M: single-phase 220÷240 V - 50 Hz with capacitor and thermal overload protector. RANGER: three-phase 380÷415 V - 50 Hz. •INSULATION: class F. • PROTECTION: IP 68. LIMITS OF USE Depth up to 5 m Liquid temperature up to + 40°C Passage of suspended solid bodies up to Ø 50 mm For continuous duty: minimum immersion 290 mm from pump base INSTALLATION AND USE THEY ARE RECOMMENDED FOR DOMESTIC, CIVIL AND INDUSTRIAL USE, IN APPLICATIONS WHERE THE WATER CONTAINS SUSPENDED SOLIDS WITH DIMENSIONS UP TO Ø 50 mm. THEIR USE IS RECOMMENDED FOR DRYING FLOODED AREAS SUCH AS CELLARS, UNDERGROUND CAR PARKS, CAR WASHING AREAS, OR domestic DRAINS AND FOR EMPTYING CESSPITS OR SEWAGE DISPOSAL. THESE PUMPS ARE OUTSTANDING IN THEIR RELIABILITY IN FIXED installaTionS WITH automatic oPERATION. ⇒control panel for three-phase pumps 1.1 kW ⇒single-phase pumps without float switch ⇒other voltages or frequency 60 Hz STANDARD FEATURES: RANGER M (single-phase) • Float switch. • Neoprene power cable “H07 RN-F” length 5 metres with Schuko plug. RANGER (three-phase) • Neoprene power cable “H07 RN-F” length 5 metres. CONSTRUCTION AND SAFETY STANDARDS EN 60 335-1 EN 60034-1 IEC 335-1 IEC 34-1 CEI 61-150 CEI 2-3 OPTIONS ON REQUEST ⇒10 metres power cable. N.B. required for outdoor use to comply to standard EN 60335-2-41 GUARANTEE 2 YEARS: subject to our general terms of sale. DIMENSIONS Typical single-phase installation b c e d h1 h DN p minimum a minimum 30 RANGER MC DOUBLE-CHANNEL submersible pumps 0 16 20 0 40 60 20 80 40 100 60 120 80 140 100 160 120 180 200 140 220 160 180 feet 50 14 RANGER MC12/50 45 40 12 RANGER MC10/50 35 10 H (m) 30 8 25 6 20 15 4 10 2 5 0 100 0 0 200 300 10 400 20 500 600 700 30 Q Q = Flow rate H = Total manometric head 0 800 40 50 Tolerance of the performance curves according to EN ISO 9906 App. A. TYPE POWER Single-phase Three-phase kW HP RANGER MC 10/50M RANGER MC 10/50 0.75 1 RANGER MC 12/50M RANGER MC 12/50 1.1 1.5 m3/h l/min H metres 0 0 12 15 3 50 10.7 14 6 100 9.7 13 9 150 8.7 12.3 12 200 7.8 11.5 15 250 6.8 10.5 18 300 5.9 9.7 21 350 5 8.8 24 400 4 8 27 450 3 7 30 500 2 6.2 36 600 42 700 48 800 4.5 2.7 1 DIMENSIONS AND WEIGHTS TYPE Single-phase DN passage of solid bodies 2” Ø 50 mm PORT Three-phase RANGER MC 10/50M RANGER MC 10/50 RANGER MC 12/50M RANGER MC 12/50 DIMENSIONS mm c h h1 kg a b d 110 90 150 410 153 55 120 97 163 430 158 65 e p adjustable 500 1~ 500 3~ 14.3 13.3 16.5 14.3 31 RANGE OF PERFORMANCE Flow rate up to 800 l/min (48 m3/h) Head up to 15 m CONSTRUCTION CHARACTERISTICS • DELIVERY BODY: cast iron, with threaded port ISO 228/1. • MOTOR CASING: stainless steel AISI 304. • BASE: stainless steel AISI 304. • IMPELLER: double-channel in stainless steel AISI 304. • MOTOR SHAFT: stainless steel EN 10088-3 - 1.4104. • DOUBLE SEAL: mechanical seal silicon carbide-ceramic -NBR, with oil barrier chamber and inner lip seal to protect the seal in the event of dry running. • MOTOR: submersible asynchronous for continuous duty. RANGER MC M: single-phase 220÷240 V - 50 Hz with capacitorr and thermal overload protector. RANGER MC: three-phase 380÷415 V - 50 Hz. •INSULATION: class F. • PROTECTION: IP 68. LIMITS OF USE Depth up to 5 m Liquid temperature up to + 40°C Passage of suspended solid bodies up to Ø 50 mm For continuous duty: minimum immersion 290 mm from pump base INSTALLATION AND USE RANGER MC SUBMERSIBLE PUMPS ARE RECOMMENDED FOR DRAINING DIRTY WATER AND SEWAGE IN THE DOMESTIC AND CIVIL SECTORS. THEY ARE EQUIPPED WITH A “DOUBLE-CHANNEL” STAINLESS STEEL IMPELLER WHICH ALLOWS THE PUMPING OF LIQUIDS CONTAINING SUSPENDED SOLID BODIES WITH DIMENSIONS UP TO Ø 50mm AND SHORT FIBRES. THEY ARE IDEAL FOR PUMPING DRAINAGE WATER, SEWAGE OR WASTE WATER FOR A SINGLE DWELLING, AND FOR CLEARING SUFACE OR NUISANCE WATER, EVEN IF MUDDY. THESE PUMPS ARE OUTSTANDING IN THEIR RELIABILITY IN FIXED installaTionS WITH automatic oPERATION. use to comply with standard EN 60335-2-41 ⇒ control box for three-phase pumps 1.1 kW ⇒ single-phase pumps without float switch ⇒ other voltages or frequency 60 Hz STANDARD FEATURES: RANGER MC M (single-phase) • Float switch. • Neoprene power cable “H07 RN-F” length 5 metres with Schuko plug. RANGER MC (three-phase) • Neoprene power cable “H07 RN-F” length 5 metres. CONSTRUCTION AND SAFETY STANDARDS EN 60 335-1 EN 60034-1 IEC 335-1 IEC 34-1 CEI 61-150 CEI 2-3 OPTIONS ON REQUEST ⇒ 10 metres power cable. N.B. required for outdoor GUARANTEE 2 YEARS subject to our general terms of sale. DIMENSIONS Typical single-phase installation b c e d h1 h DN p minimum a minimum 32 RANGER SS VORTEX submersible pumps RANGER 10/35SS RANGER 08/35SS H (m) RANGER 10/50SS RANGER 08/50SS Q Q = Flow rate H = Total manometric head TYPE Single-phase Three-phase RANGER 8/35M SS ––– RANGER 10/35M SS RANGER 10/35SS RANGER 8/50M SS ––– RANGER 10/50M SS RANGER 10/50SS Tolerance of the performance curves according to EN ISO 9906 App. A. POWER m3/h l/min kW HP 0.60 0.85 0.75 1 H metres 0.60 0.85 0.75 1 0 0 8.4 10 6 7.5 3 50 7.5 9.5 5.5 7 6 100 6.5 8.5 5 6.5 9 150 5.2 7.2 4.4 5.8 12 200 3.7 5.8 3.6 5 15 250 2 4 2.8 4 18 300 21 350 24 400 2 2 3.2 1 2.4 1.5 DIMENSIONS AND WEIGHTS TYPE Single-phase RANGER 8/35M SS ––– RANGER 10/35M SS RANGER 10/35SS RANGER 8/50M SS DN passage of solid bodies a 11/2” Ø 35 mm 108 2” Ø 50 mm 118 PORT Three-phase ––– RANGER 10/50M SS RANGER 10/50SS DIMENSIONS mm b h h1 d 380 87 40 410 108 55 166 kg e adjustable p 500 1~ 500 3~ 9.7 - 9.6 9.3 12.8 - 10.7 9.7 33 RANGE OF PERFORMANCE Flow rate up to 400 l/min (24 m3/h) Head up to 10 m CONSTRUCTION CHARACTERISTICS • DELIVERY BODY: stainless steel AISI 304, with threaded port ISO 228/1. • MOTOR CASING AND BASE: stainless steel AISI 304. • IMPELLER: stainless steel AISI 304. • MOTOR SHAFT: stainless steel AISI 316. • DOUBLE SEAL: mechanical seal silicon carbide - ceramic - NBR - stainless steal AISI 316, with oil barrier chamber and inner lip seal to protect the seal in the event of dry running. • MOTOR: submersible asynchronous for continuous duty. RANGER M SS: single-phase 220÷240 V - 50 Hz with capacitor and thermal overload protector. RANGER SS: three-phase 380÷415 V - 50 Hz. •INSULATION: class F. • PROTECTION: IP 68. LIMITS OF USE Depth up to 5 m Liquid temperature up to + 40°C Passage of suspended solid bodies up to Ø 50 mm For continuous duty: minimum immersion 280 mm from pump base. INSTALLATION AND USE THEY ARE RECOMMENDED FOR DRAINING WASTE WATER IN THE DOMESTIC, CIVIL AND INDUSTRIAL SECTORS, IN APPLICATIONS WHERE THE WATER CONTAINS SUSPENDED SOLIDS WITH DIMENSIONS UP TO Ø 50 mm. THEIR USE IS RECOMMENDED FOR DRYING FLOODED AREAS SUCH AS CELLARS, UNDERGROUND CAR PARKS, CAR WASHING AREAS and fOR EMPTYING CESSPITS or SEWAGE DISPOSAL. THESE PUMPS ARE OUTSTANDING in THEIR RELIABILITY IN FIXED installaTionS WITH automatic oPERATION. STANDARD FEATURES: RANGER M SS (single-phase) •Flow switch. •Neoprene power cable “H07 RN-F” length 5 metres with Schuko plug. RANGER SS (three-phase) •Neoprene power cable “H07 RN-F” length 5 metres. GUARANTEE 2 YEARS subject to our general terms of sale. OPTIONS ON REQUEST ⇒10 metres power cable. N.B. required for outdoor use to comply with standard EN 60335-2-41 ⇒single-phase pumps without float switch ⇒other voltages or frequency 60 Hz CONSTRUCTION AND SAFETY STANDARDS EN 60 335-1 EN 60034-1 IEC 335-1 IEC 34-1 CEI 61-150 CEI 2-3 DIMENSIONS Typical single-phase installation b e d h1 DN h p minimum a minimum 34 RANGER MC SS DOUBLE-CHANNEL submersible pumps 0 16 20 0 40 60 20 80 40 100 60 120 80 140 100 160 120 180 200 140 220 160 180 feet 50 RANGER MC 15/50SS 14 45 40 12 RANGER MC 10/50SS 35 10 30 H (m) 8 25 6 20 15 4 10 2 5 0 100 0 0 200 300 400 10 20 500 700 30 Q 0 800 40 Q = Flow rate H = Total manometric head TYPE Single-phase Three-phase RANGER MC 10/50M SS RANGER MC 10/50SS ––– RANGER MC 15/50SS 600 50 Tolerance of the performance curves according to EN ISO 9906 App. A. POWER kW HP 0.75 1 1.1 1.5 0 0 12 15 m3/h l/min H metres 3 50 10.7 14 6 100 9.7 13 9 150 8.7 12.3 12 200 7.8 11.5 15 250 6.8 10.5 18 300 5.9 9.7 21 350 5 8.8 24 400 4 8 27 450 3 7 30 500 2 6.2 36 600 42 700 48 800 4.5 2.7 1 DIMENSIONS AND WEIGHTS TYPE Single-phase RANGER MC 10/50M SS RANGER MC 10/50SS ––– DN passage of solid bodies a b h h1 d e p 2” Ø 50 mm 118 166 410 109 55 adjustable 500 PORT Three-phase RANGER MC 15/50SS DIMENSIONS mm kg 1~ 500 3~ 12.8 9.8 - 12.8 35 RANGE OF PERFORMANCE Flow rate up to 800 l/min (48 m3/h) Head up to 15 m CONSTRUCTION CHARACTERISTICS • DELIVERY BODY: stainless steel AISI 304, with threaded port ISO 228/1. • MOTOR CASING AND BASE: stainless steel AISI 304. • IMPELLER: double-channel, in stainless steel AISI 304. • MOTOR SHAFT: stainless steel AISI 316. • DOUBLE SEAL: mechanical seal silicon carbide - ceramic - NBR - stainless steal AISI 316, with oil barrier chamber and inner lip seal to protect the seal in the event of dry running. • MOTOR: submersible asynchronous for continuous duty. RANGER MC M SS: single-phase 220÷240 V - 50 Hz with capacitor and thermal overload protector. RANGER MC SS: three-phase 380÷415V - 50 Hz. •INSULATCION: class F. • PROTECTION: IP 68. LIMITS OF USE Depth up to 5 m Liquid temperature up to + 40°C Passage of suspended solid bodies up to Ø 50 mm For continuous duty: minimum immersion 280 mm from pump base INSTALLATION AND USE RANGER MC SS SUBMERSIBLE PUMPS ARE RECOMMENDED FOR DRAINING DIRTY WATER AND SEWAGE IN THE DOMESTIC AND CIVIL SECTORS. THEY ARE EQUIPPED WITH A “DOUBLE-CHANNEL” STAINLESS STEEL IMPELLER WHICH ALLOWS THE PUMPING OF LIQUIDS CONTAINING SUSPENDED SOLID BODIES WITH DIMENSIONS UP TO Ø 50 mm AND SHORT FIBRES. THEY ARE IDEAL FOR PUMPING DRAINAGE WATER, SEWAGE OR WASTE WATER FOR A SINGLE DWELLING, AND FOR CLEARING SUrFACE OR NUISANCE WATER, EVEN IF MUDDY. THESE PUMPS ARE OUTSTANDING IN THEIR RELIABILITY IN FIXED installaTionS WITH automatic oPERATION. STANDARD FEATURES: RANGER MC M SS (single-phase) •Flow switch. •Neoprene power cable “H07 RN-F” length 5 metres with Schuko plug. RANGER MC SS (three-phase) • N eoprene power cable “H07 RN-F” length 5 metres. GUARANTEE 2 YEARS subject to our general terms of sale. OPTIONS ON REQUEST ⇒10 metres power cable. N.B. required for outdoor use to comply with standard EN 60335-2-41 ⇒ control box for three-phase pumps 1.1 kW ⇒ single-phase pumps without float switch ⇒ other voltages or frequency 60 Hz CONSTRUCTION AND SAFETY STANDARDS EN 60 335-1 EN 60034-1 IEC 335-1 IEC 34-1 CEI 61-150 CEI 2-3 DIMENSIONS p minimum h b d h1 DN e Typical single-phase installation a minimum 36 SECURITY G DRAINAGE submersible pumps SECURITY 30G SECURITY 20G SECURITY 15G SECURITY 18G H (m) SECURITY 10G SECURITY 8G SECURITY 6G Q Q = Flow rate H = Total manometric head TYPE Single-phase Three-phase SECURITY G 6M ––– SECURITY G 8M ––– SECURITY G 10M SECURITY G 10 SECURITY G 15M SECURITY G 15 SECURITY G 18M ––– SECURITY G 20M SECURITY G 20 SECURITY G 30M SECURITY G 30 Tolerance of the performance curves according to EN ISO 9906 App. A. POWER 0 m3/h l/min kW HP 0 0.45 0.60 9 0.60 0.85 12 0.75 1 15 1.1 1.5 H metres 19.5 0.6 0.85 17 0.75 1 21 1.1 1.5 27 1.5 25 8.5 11.5 14.5 19 16.5 20 26 3.0 50 8 11 14 18.5 15 19 25 4.5 75 7.5 10.5 13.2 18 13.5 17.5 23.5 6.0 100 6.8 9.8 12.5 17.5 12 16 22 7.5 125 6 9 11.8 16.5 10.7 15 21 9.0 150 5.2 8.2 11 16 9 13.5 19.5 10.5 175 4 7.2 10 15 7.7 12 18 12.0 200 2.6 6 9 14 5 10 16 13.5 225 1 4.8 8 13 15.0 250 16.5 275 18.0 300 19.5 325 21.0 350 24.0 400 3.5 6.8 11.8 2 5.4 10.5 3.5 9.2 2 8 7 4 14.5 13 11.5 10 DIMENSIONS AND WEIGHTS TYPE Single-phase PORT Three-phase SECURITY G 6M ––– SECURITY G 8M ––– SECURITY G 10M SECURITY G 10 SECURITY G 15M SECURITY G 15 SECURITY G 18M ––– SECURITY G 20M SECURITY G 20 SECURITY G 30M SECURITY G 30 DN DIMENSIONS mm a b 105 11/2” 110 c 136 90 140 h 285 310 h1 m n kg o d e p 66 80 105 136 285 66 110 140 310 80 81 200 66 15 adjustable 500 500 1~ 3~ 14.8 - 16.1 - 17.1 16.1 19.3 18.2 16.1 - 17.1 16.1 19.3 18.2 37 RANGE OF PERFORMANCE Flow rate up to 400 l/min (24 m3/h) Head up to 27 m LIMITS OF USE Depth up to 10 m Liquid temperature up to + 40°C Passage of suspended solid bodies up to Ø 10 mm Drainage level to 15 mm from the bottom For continuous duty: minimum immersion 210 mm from pump base INSTALLATION AND USE SECURITY G SUBMERSIBLE PUMPS, MADE OF EXCEPTIONALLY STURDY HEAVY-GAUGE CAST IRON, RESISTANT TO ABRASION AND LONG-LASTING, ARE RECOMMENDED FOR DRAINING CLEAR OR SLIGHTLY DIRTY WATER AND FOR DISPOSING OF NON-SEWAGE WASTE WATER; THEY ARE OUTSTANDING BOTH IN THEIR STURDINESS AND THEIR RELIABILITY IN FIXED installaTionS WITH automatic oPERATION. GUARANTEE 2 YEARS subject to our general terms of sale. CONSTRUCTION CHARACTERISTICS • PUMP BODY: cast iron, with threaded port ISO 228/1. • MOTOR CASING: cast iron. • SUCTION GRID: stainless steel AISI 304. • IMPELLER: cast iron. • MOTOR SHAFT: stainless steel EN 10088-3 - 1.4104. • DOUBLE SEAL: mechanical seal silicon carbide -ceramic - NBR, with oil barrier chamber and inner lip seal to protect the seal in the event of dry running. • MOTOR: submersible asynchronous for continuous duty. SECURITY G M: single-phase 220÷240 V - 50 Hz with thermal overload protector. SECURITY G: three-phase 380÷415 V - 50 Hz. •INSULATION: class F. • PROTECTION: IP 68. STANDARD FEATURES: SECURITY G M (single-phase) •Float switch. •Neoprene power cable “H07 RN-F” length 10 metres with Schuko plug. •Electric panel with capacitor. SECURITY G (three-phase) •Neoprene power cable “H07 RN-F” length 10 metres. OPTIONS ON REQUEST ⇒control box for three-phase pumps 1.1 kW ⇒single-phase pumps without float switch ⇒other voltages or frequency 60 Hz CONSTRUCTION AND SAFETY STANDARDS EN 60034-1 IEC 34-1 CEI 2-3 DIMENSIONS Typical installation a DN o b c d h1 m e n h p minimum SINGLE-PHASE CONTROL BOX minimum 38 TITAN 35-45 VORTEX submersible pumps TITAN 15/35 TITAN 15/45 H (m) TITAN 10/35 TITAN 8/35 TITAN 10/45 TITAN 8/45 Q Q = Flow rate H = Total manometric head TYPE Single-phase TITAN 8/35M TITAN 10/35M TITAN 15/35M TITAN 8/45M TITAN 10/45M TITAN 15/45M Three-phase ––– TIATN 10/35 TITAN 15/35 ––– TITAN 10/45 TITAN 15/45 Tolerance of the performance curves according to EN ISO 9906 App. A. POWER m3/h l/min kW HP 0.60 0.85 0.75 1 1.1 1.5 H metres 0.60 0.85 0.75 1 1.1 1.5 0 0 8.4 10 15 6 7.5 11 3 50 7.5 9.5 14 5.5 7 10.5 6 100 6.5 8.5 13 5 6.5 10 9 150 5.2 7.2 11.8 4.4 5.8 9.5 12 200 3.7 5.8 10.5 3.6 5 9 15 250 2 4 9 2.8 4 8.3 18 300 21 350 24 400 27 450 2 7.5 2 3.2 7.5 6 1 2.4 6.8 4 2 1.5 6 5 30 500 4 DIMENSIONS AND WEIGHTS TYPE Single-phase DN passage of solid bodies 11/2” Ø 35 mm PORT Three-phase TITAN 8/35M ––– TITAN 10/35M TITAN 10/35 TITAN 15/35M TITAN 15/35 TITAN 8/45M ––– TITAN 10/45M TITAN 10/45 TITAN 15/45M TITAN 15/45 DIMENSIONS mm a b c h h1 105 90 137 350 123 92 143 370 133 110 2” Ø 45 mm 120 90 150 375 148 97 163 395 153 m n kg o d e p 1~ 40 81 200 adjustable 66 55 500 500 3~ 17.0 - 18.7 17.1 20.9 19.8 18.0 - 19.7 18.0 21.9 20.8 39 RANGE OF PERFORMANCE Flow rate up to 500 l/min (30 m3/h) Head up to 15 m LIMITS OF USE Depth up to 10 m Liquid temperature up to + 40°C Passage of solid bodies max Ø 35 mm for TITAN/35 Passage of solid bodies max Ø 45 mm for TITAN/45 For continuous duty: minimum immersion 290 mm from pump base INSTALLATION AND USE THE PUMPS IN THE TITAN SERIES ARE MADE OF EXCEPTIONALLY ROBUST HEAVY-GAUGE CAST IRON, RESISTANT TO ABRASION AND ARE equipPED WITH A VORTEX TYPE IMPELLER. THEY ARE RECOMMENDED FOR DRAINING WASTE WATER CONTAINING SUSPENDED SOLID BODIES, SEWAGE AND WATER MIXED WITH MUD. GUARANTEE 2 YEARS subject to our general terms of sale. CONSTRUCTION CHARACTERISTICS • PUMP BODY: cast iron, with threaded port ISO 228/1. • MOTOR CASING AND BASE: cast iron. • IMPELLER: vortex in stainless steel AISI 304. • MOTOR SHAFT: stainless steel EN 10088-3 - 1.4104. • DOUBLE SEAL: mechanical seal silicon carbide - ceramic - NBR, with oil barrier chamber and inner lip seal to protect the seal in the event of dry running. • MOTOR: submersible asynchronous for continuous duty. TITAN M: single-phase 220÷240 V - 50 Hz with thermal overload protector. TITAN: three-phase 380÷415 V - 50 Hz. •INSULATION: class F. • PROTECTION: IP 68. STANDARD FEATURES: TITAN M (single-phase) • Float switch. • Neoprene power cable “H07 RN-F” length 10 metres with Schuko plug. • Control box with capacitor (Protection IP 64). TITAN (three-phase) • Neoprene power cable “H07 RN-F” length 10 metres. CONSTRUCTION AND SAFETY STANDARDS EN 60034-1 IEC 34-1 CEI 2-3 OPTIONS ON REQUEST ⇒control box for three-phase pumps 1.1 kW ⇒single-phase pumps without float switch ⇒other voltages or frequency 60 Hz DIMENSIONS Typical installation a e o b c d h1 m p minimum DN h n SINGLE-PHASE CONTROL BOX minimum 40 PATROL 45 DOUBLE-CHANNEL submersible pumps PATROL 15/45 H (m) PATROL 10/45 Q Q = Flow rate H = Total manometric head TYPE Single-phase PATROL 10/45M PATROL 15/45M Three-phase PATROL 10/45 PATROL 15/45 Tolerance of the performance curves according to EN ISO 9906 App. A. POWER kW HP 0.75 1 1.1 1.5 m3/h l/min H metres 0 0 12 15 3 50 10.7 14 6 100 9.7 13 9 150 8.7 12.3 12 200 7.8 11.5 15 250 6.8 10.5 18 300 5.9 9.7 21 350 5 8.8 24 400 4 8 27 450 3 7 30 500 2 6.2 36 600 42 700 48 800 4.5 2.7 1 DIMENSIONS AND WEIGHTS TYPE Single-phase DN passage of solid bodies 2” Ø 45 mm PORT Three-phase PATROL 10/45M PATROL 10/45 PATROL 15/45M PATROL 15/45 DIMENSIONS mm a b 110 90 120 97 c h h1 150 375 148 163 395 153 kg m n o d e p 81 200 66 55 adjustable 500 500 1~ 3~ 19.9 18.3 22.1 21.0 41 RANGE OF PERFORMANCE Flow rate up to 800 l/min (48 m3/h) Head up to 15 m LIMITS OF USE Depth up to 10 m Liquid temperature up to + 40°C Passage of suspended solid bodies up to Ø 45 mm For continuous duty: minimum immersion 290 mm from pump base INSTALLATION AND USE THE PUMPS IN THE PATROL series ARE MADE OF EXCEPTIONALLY ROBUST HEAVY-GAUGE CAST IRON, RESISTANT TO ABRASION AND LONG-LASTING. THEY ARE EQUIPPED WITH A DOUBLE-CHANNEL IMPELLER WHICH ALLOWS THE DRAINAGE OF LIQUIDS CONTAINING SUSPENDED SOLID BODIES WITH DIMENSIONS UP TO Ø 45 mm AND SHORT FIBRES. THEY ARE IDEAL FOR PUMPING DRAINAGE WATER AND SEWAGE, WASTE WATER INCLUDING WATER MIXED WITH MUD, GROUNDWATER AND SURFACE WATER IN APPLICATIONS SUCH AS: condominiUMS, MULTI-STOREY AND UNDERGROUND CAR PARKS, WASHING AREAS AND INDUSTRY. GUARANTEE 2 YEARS subject to our general terms of sale. CONSTRUCTION CHARACTERISTICS • PUMP BODY: cast iron, with threaded port ISO 228/1. • MOTOR CASING AND BASE: cast iron. • IMPELLER: double-channel, in stainless steel AISI 304. • MOTOR SHAFT: stainless steel EN 10088-3 - 1.4104. • DOUBLE SEAL: mechanical seal silicon carbide -ceramic - NBR, with oil barrier chamber and inner lip seal to protect the seal in the event of dry running. • MOTOR: submersible asynchronous for continuous duty. PATROL M: single-phase 220÷240 V - 50 Hz with thermal overload protector. PATROL: three-phase 380÷415 V - 50 Hz. •INSULATION: class F. • PROTECTION: IP 68. OPTIONS ON REQUEST ⇒control box for three-phase pumps 1.1 kW ⇒single-phase pumps without float switch ⇒other voltages or frequency 60 Hz STANDARD FEATURES: PATROL M (single-phase) • Float switch. • Neoprene power cable “H07 RN-F” length 10 metres with Schuko plug. • Control box with condenser. PATROL (three-phase) • Neoprene power cable “H07 RN-F” length 10 metres. CONSTRUCTION AND SAFETY STANDARDS EN 60034-1 IEC 34-1 CEI 2-3 DIMENSIONS Typical installation a o b c e d h1 m p minimum DN h n SINGLE-PHASE CONTROL BOX minimum 42 TITAN 50-70 VORTEX submersible pumps TITAN 30/50 TITAN 20/50 TITAN 15/50 H (m) TITAN 30/70 TITAN 20/70 TITAN 15/70 Q Q = Flow rate H = Total manometric head TYPE Single-phase TITAN 15/50M TITAN 20/50M TITAN 30/50M TITAN 15/70M TITAN 20/70M TITAN 30/70M Three-phase TITAN 15/50 TITAN 20/50 TITAN 30/50 TITAN 15/70 TITAN 20/70 TITAN 30/70 Tolerance of the performance curves according to EN ISO 9906 App. A. POWER kW HP 1.1 1.5 1.5 2 2.2 3 1.1 1.5 1.5 2 2.2 3 0 0 11.5 13 16 H metres 6.5 8.5 11 6 100 10.5 12 15 ––– ––– ––– m3/h l/min 12 200 9.5 11 14 5.5 7.4 9.7 18 300 8.2 9.5 13 5 6.7 9 21 350 7.2 9 12.3 4.7 6.3 8.6 24 400 6.5 8 11.5 4.4 6 8.2 30 500 4.5 6.5 10 3.7 5.2 7.5 36 600 2 4.5 8 3 4.5 6.7 42 700 48 800 51 850 54 900 60 1000 66 1100 72 1200 2 5.9 2.2 3.6 5.8 3.3 1.5 2.8 5 2 1 2.4 4.6 2 4.2 1 3.3 2.5 1.5 DIMENSIONS AND WEIGHTS TYPE Single-phase DN passage of solid bodies a b c 21/2” Ø 50 mm 162 135 212 PORT Three-phase TITAN 15/50M TITAN 15/50 TITAN 20/50M TITAN 20/50 TITAN 30/50M TITAN 30/50 TITAN 15/70M TITAN 15/70 TITAN 20/70M TITAN 20/70 TITAN 30/70M TITAN 30/70 DIMENSIONS mm h 490 h1 Ø 70 mm 180 150 240 530 540/530 n kg o 188 500/490 3” m e p 1~ 75 81 230 d 200 adjustable 85 85 800 800 3~ 33.3 31.0 34.8 33.3 40.7 34.8 38.9 36.6 40.8 38.9 47.0 41.1 43 RANGE OF PERFORMANCE Flow rate up to 1200 l/min (72 m3/h) Head up to 16 m LIMITS OF USE Depth up to 10 m Liquid temperature up to + 40°C Passage of solid bodies max Ø 50 mm for TITAN 15-20-30/50 Passage of solid bodies max Ø 70 mm for TITAN 15-20-30/70 For continuous duty: minimum immersion 420 mm from pump base INSTALLATION AND USE TITAN series PUMPS ARE MADE OF EXCEPTIONALLY ROBUST HEAVY-GAUGE CAST IRON, RESISTANT TO ABRASION AND LONG-LASTING, AND HAVE A VORTEX TYPE IMPELLER. THEY ARE SUITABLE FOR SEWAGE, WASTE WATER AND SLUDGE, INCLUDING WATER CONTAINING SOLIDS OR MUD. THEY ARE iDEAL FOR SEWAGE installaTion, TUNNELS AND OTHER EXCAVATIONS, UNDERGROUND CAR PARKS AND SIMILAR APPLICATIONS. GUARANTEE 2 YEARS subject to our general terms of sale. CONSTRUCTION CHARACTERISTICS • PUMP BODY, MOTOR CASING: cast iron. • IMPELLER: cast iron. • BASE: stainless steel AISI 304. • MOTOR SHAFT: vortex, stainless steel EN 10088-3 - 1.4057. • DOUBLE SEAL: mechanical seal silicon carbide - widia -NBR, with oil barrier chamber and inner lip seal to protect the seal in the event of dry running. • MOTOR: submersible asynchronous, 2 pole, for continuous duty. TITAN M: single-phase 220÷240 V - 50 Hz Models up to 1.5 kW have built in thermal protection 2.2 kW single-phase versions have a thermal protector provided in the winding for connection to the control box. TITAN: three-phase 380÷415 V - 50 Hz. Thermal protectors are provided in the winding for connection to the external control panel •INSULATION: class F. • PROTECTION: IP 68. OPTIONS ON REQUEST ⇒control box for three-phase pumps ⇒dual voltage: 230/400 V or 400/690 V ⇒single-phase versions without float switch ⇒other voltages or frequency 60 Hz STANDARD FEATURES: TITAN M (single-phase) •Float switch. •10 metres “H07 RN-F” submersible power cable with Schuko plug. •1.1 to 1.5 kW models are supplied with control box with capacitor and manual reset motor protector. 2.2 kW models are supplied with control box type QES 300 MONO. TITAN (three-phase) •10 metres “H07 RN-F” neoprene power cable CONSTRUCTION AND SAFETY STANDARDS EN 60034-1 IEC 34-1 CEI 2-3 DIMENSIONS Typical single-phase installation a SINGLE-PHASE CONTROL BOX b c e d o h1 m p minimum n h DN minimum 44 PATROL 50-70 SINGLE-CHANNEL submersible pumps PATROL PATROL 30/50 30/50 PATROL 20/50 H (m) PATROL 15/50 PATROL 30/70 Q Q = Flow rate H = Total manometric head TYPE Single-phase Three-phase PATROL 15/50M PATROL 15/50 PATROL 20/50M PATROL 20/50 PATROL 30/50M PATROL 30/50 PATROL 30/70M PATROL 30/70 Tolerance of the performance curves according to EN ISO 9906 App. A. POWER kW HP 1.1 1.5 1.5 2 2.2 3 2.2 3 m3/h l/min H metres 0 0 16 18 24 13 3 50 ––– ––– ––– ––– 6 100 14 16 22 ––– 12 200 12.5 14 20 11.5 18 300 10.5 12.5 18 11 24 400 8.5 10.5 16 10.2 30 500 7 9 14 9.5 36 600 5 7 12 8.8 42 700 3 5 10 8.2 48 800 1 3 8 7.6 54 900 1 6 6.8 60 66 72 84 96 1000 1100 1200 1400 1600 4 6 2 5.3 4.8 3.2 2 DIMENSIONS AND WEIGHTS TYPE Single-phase DN passage of solid bodies a b c 21/2” Ø 50 mm 162 135 212 PORT Three-phase PATROL 15/50M PATROL 15/50 PATROL 20/50M PATROL 20/50 PATROL 30/50M PATROL 30/50 PATROL 30/70M PATROL 30/70 DIMENSIONS mm h 490 h1 188 500/490 3” Ø 70 mm 180 150 240 540/530 230 m 81 n 200 kg o 85 d e 75 adjustable 85 p 800 1~ 800 3~ 34.0 31.8 35.7 34.0 41.7 35.8 48.0 42.1 45 RANGE OF PERFORMANCE Flow rate up to 1600 l/min (96 m3/h) Head up to 24 m LIMITS OF USE Depth up to 10 m Liquid temperature up to + 40°C Passage of solid bodies max Ø 50 mm for PATROL 15-20-30/50 P Passage of solid bodies max Ø 70 mm for PATROL 30/70 P For continuous duty: minimum immersion 420 mm from pump base INSTALLATION AND USE PATROL SERIES PUMPS ARE MADE OF EXCEPTIONALLY ROBUST HEAVY GAUGE CAST IRON, ABRASION RESISTANT AND LONG-LASTING, WITH A SINGLE-CHANNEL IMPELLER WHICH CAN HANDLE LIQUIDS WITH SUSPENDED SOLIDS AND SHORT FIBRES. THEY ARE iDEAL FOR SEWAGE, WASTE AND GROUND WATER, EVEN WITH SOLIDS OR MUD, AND ARE THEREFORE RECOMMENDED FOR BUILDING OR INDUSTRIAL EFFLUENT AND DRAINAGE OF LARGE AREAS SUCH AS CAR PARKS. GUARANTEE 2 YEARS subject to our general terms of sale. CONSTRUCTION CHARACTERISTICS • PUMP BODY, MOTOR CASING: cast iron. • IMPELLER: single-channel, in cast iron. • BASE: stainless steel AISI 304. • MOTOR SHAFT: stainless steel EN 10088-3 - 1.4057. • DOUBLE SEAL: mechanical seal silicon carbide - widia - NBR, with oil barrier chamber and inner lip seal to protect the seal in the event of dry running. • MOTOR: submersible asynchronous, 2 pole, for continuous duty. PATROL M: single-phase 220÷240 V - 50 Hz Models up to 1.5 kW have built in thermal protection - 2.2 kW single-phase versions have a thermal protector provided in the winding for connection to the control box. PATROL: three-phase 380÷415 V - 50 Hz. Thermal protectors are provided in the winding for connection to the external control panel •INSULATION: class F. •PROTECTION: IP 68. OPTIONS ON REQUEST ⇒control box for three-phase pumps ⇒dual voltage: 230/400 V or 400/690 V ⇒single-phase versions without float switch ⇒other voltages or frequency 60 Hz STANDARD FEATURES: PATROL M (single-phase) •Float switch. •10 metres “H07 RN-F” submersible power cable with Schuko plug. •1.1 to 1.5 kW models are supplied with control box with capacitor and manual reset motor protector. 2.2 kW models are supplied with control box type QES 300 MONO. PATROL (three-phase) •10 metres “H07 RN-F” neoprene power cable CONSTRUCTION AND SAFETY STANDARDS EN 60034-1 IEC 34-1 CEI 2-3 DIMENSIONS Typical installation a SINGLE-PHASE CONTROL BOX o b c e d h1 m p minimum n h DN minimum 46 stationary version TITAN P VORTEX submersible pumps TITAN 30/50P TITAN 20/50P TITAN 15/50P H (m) TITAN 30/70P TITAN 20/70P TITAN 15/70P Q Q = Flow rate H = Total manometric head TYPE Single-phase TITAN 15/50PM TITAN 20/50PM TITAN 30/50PM TITAN 15/70PM TITAN 20/70PM TITAN 30/70PM Three-phase TITAN 15/50P TITAN 20/50P TITAN 30/50P TITAN 15/70P TITAN 20/70P TITAN 30/70P Tolerance of the performance curves according to EN ISO 9906 App. A. POWER kW HP 1.1 1.5 1.5 2 2.2 3 1.1 1.5 1.5 2 2.2 3 0 0 11.5 13 16 H metres 6.5 8.5 11 6 100 10.5 12 15 ––– ––– ––– m3/h l/min 12 200 9.5 11 14 5.5 7.4 9.7 18 300 8.2 9.5 13 5 6.7 9 21 350 7.2 9 12.3 4.7 6.3 8.6 24 400 6.5 8 11.5 4.4 6 8.2 27 450 5.6 7,2 10.8 4 5.6 7.8 30 500 4.5 6.5 10 3.7 5.2 7.5 36 600 2 4.5 8 3 4.5 6.7 42 700 48 800 51 850 54 900 2 5.9 2.2 3.6 5.8 3.3 1.5 2.8 5 2 1 2.4 4.6 2 4.2 60 66 72 1000 1100 1200 1 3.3 2.5 1.5 DIMENSIONS AND WEIGHTS TYPE Single-phase PORT Three-phase TITAN 15/50PM TITAN 15/50P TITAN 20/50PM TITAN 20/50P TITAN 30/50PM TITAN 30/50P TITAN 15/70PM TITAN 15/70P TITAN 20/70PM TITAN 20/70P TITAN 30/70PM TITAN 30/70P DN passage of solid bodies DIMENSIONS mm a 21/2” Ø 50 mm b c d e f 116 51 501 62 270 60 3” Ø 70 mm kg* g 387 10 150 70 585 95 300 h m n w 1~ 3~ 42.0 40.0 200 120 72 43.8 42.3 397/387 405 415/405 256 150 92 49.7 43.8 53.0 50.7 54.9 53.0 61.1 55.2 (*weight including counterflange) 47 • MOTOR SHAFT: stainless steel EN 10088-3 - 1.4057. • DOUBLE SEAL: mechanical seal silicon carbide - widia - NBR, with oil barrier chamber and inner lip seal to protect the seal in the event of dry running. • MOTOR: submersible asynchronous, 2 pole, for continuous duty. TITAN P M: single-phase 220÷240 V - 50 Hz Models up to 1.5 kW have built in thermal protection. 2.2 kW single-phase versions have a thermal protector provided in the winding for connection to the control box. TITAN P: three-phase 380÷415 V - 50 Hz. Thermal protectors are provided in the winding for connection to the external control panel •INSULATION: class F. • PROTECTION: IP 68. RANGE OF PERFORMANCE Flow rate up to 1200 l/min (72 m3/h) Head up to 16 m LIMITS OF USE Depth up to 10 m Liquid temperature up to + 40°C Passage of solid bodies max Ø 50 mm for TITAN 15-20-30/50 P Passage of solid bodies max Ø 70 mm for TITAN 15-20-30/70 P For continuous duty: minimum immersion 430 mm from pump base INSTALLATION AND USE TITAN P SERIES PUMPS ARE MADE OF EXCEPTIONALLY ROBUST HEAVY GAUGE CAST IRON, RESISTANT TO ABRASION AND LONG LASTING, AND HAVE A VORTEX TYPE IMPELLER. THEY ARE SUITABLE FOR SEWAGE, WASTE WATER AND SLUDGE, INCLUDING WATER CONTAINING SOLIDS OR MUD. THEY ARE IDEAL FOR FIXED SEWAGE INSTALLATIONS, TUNNELS, UNDERGROUND CARPARKS, SUMPS AND SIMILAR APPLICATIONS. STANDARD FEATURES: • Base pedestal elbow (duct foot) • Threaded delivery counterflange • Top supports for guide tubes TITAN P M (single-phase) • Float switch. • 10m “H07 RN-F” submersible power cable with Schuko plug. • 1.1 to 1.5 kW models are supplied with control box with capacitor and manual reset motor protector. 2.2 kW models are supplied with control box type QES 300 MONO. TITAN P (three-phase) • 10m “H07 RN-F” neoprene power cable GUARANTEE 2 YEARS subject to our general terms of sale. CONSTRUCTION CHARACTERISTICS • PUMP BODY, MOTOR CASING AND BASE PEDESTAL: cast iron. • IMPELLER: vortex in cast iron. • BASE: stainless steel AISI 304. OPTIONS ON REQUEST ⇒control box for three-phase pumps ⇒dual voltage: 230/400 V or 400/690 V ⇒single-phase versions without float switch ⇒other voltages or frequency 60 Hz CONSTRUCTION AND SAFETY STANDARDS EN 60034-1 IEC 34-1 CEI 2-3 DIMENSIONS Typical installation a Guide tubes Ø external 27 mm maximum Ø internal 19.5÷21.5 mm w DN b g m d h c e n f 48 stationary version PATROL P SINGLE-CHANNEL submersible pumps PATROL 30/50P PATROL 20/50P H (m) PATROL 15/50P PATROL 30/70P Q Q = Flow rate H = Total manometric head TYPE Single-phase Three-phase PATROL 15/50PM PATROL 15/50P PATROL 20/50PM PATROL 20/50P PATROL 30/50PM PATROL 30/50P PATROL 30/70PM PATROL 30/70P Tolerance of the performance curves according to EN ISO 9906 App. A. POWER kW HP 1.1 1.5 1.5 2 2.2 3 2.2 3 m3/h l/min H metres 0 0 16 18 24 13 6 100 14 16 22 ––– 12 200 12.5 14 20 11.5 15 250 11.5 13 19 11.2 18 300 10.5 12.5 18 11 24 400 8.5 10.5 16 10.2 30 500 7 9 14 9.5 36 600 5 7 12 8.8 42 700 3 5 10 8.2 48 800 1 3 8 7.6 54 900 1 6 6.8 60 66 72 84 96 1000 1100 1200 1400 1600 4 6 2 5.3 4.8 3.2 2 DIMENSIONS AND WEIGHTS TYPE Single-phase Three-phase PORT passage of solid DN bodies DIMENSIONS mm a b c d e f 116 51 501 62 270 kg* g PATROL 15/50PM PATROL 15/50P PATROL 20/50PM PATROL 20/50P 21/2” Ø 50 mm PATROL 30/50PM PATROL 30/50P PATROL 30/70PM PATROL 30/70P 3” Ø 70 mm 60 150 70 585 95 300 h 387 10 m n w 1~ 3~ 43.0 40.8 200 120 72 44.7 43.0 50.7 44.8 62.0 56.1 397/387 415/405 256 150 92 (*weight including counterflange) 49 RANGE OF PERFORMANCE Flow rate up to 1600 l/min (96 m3/h) Head up to 24 m • MOTOR SHAFT: stainless steel EN 10088-3 - 1.4057. • DOUBLE SEAL: mechanical seal silicon carbide - widia - NBR, with oil barrier chamber and inner lip seal to protect the seal in the event of dry running. • MOTOR: submersible asynchronous, 2 pole, for continuous duty. PATROL PM: single-phase 220÷240 V - 50 Hz. Models up to 1.5 kW have built in thermal protection. 2.2 kW single-phase versions have a thermal protector provided in the winding for connection to the control box. PATROL P: three-phase 380÷415 V - 50 Hz. Thermal protectors are provided in the winding for connection to the external control panel •INSULATION: class F. • PROTECTION: IP 68. LIMITS OF USE Depth up to 10 m Liquid temperature up to + 40°C Passage of solid bodies max Ø 50 mm for PATROL P 15-20-30/50 Passage of solid bodies max Ø 70 mm for PATROL P 30/70 For continuous duty: minimum immersion 430 mm from pump base INSTALLATION AND USE PATROL P SERIES PUMPS ARE MADE OF EXCEPTIONALLY ROBUST HEAVY GAUGE CAST IRON, ABRASION RESISTANT AND LONG-LASTING, WITH A SINGLE-CHANNEL IMPELLER WHICH CAN HANDLE LIQUIDS WITH SUSPENDED SOLIDS AND SHORT FIBRES. THEY ARE iDEAL FOR SEWAGE, WASTE AND GROUND WATER, EVEN WITH SOLIDS OR MUD, AND ARE THEREFORE RECOMMENDED FOR BUILDING OR INDUSTRIAL EFFLUENT AND DRAINAGE OF LARGE AREAS SUCH AS CAR PARKS. STANDARD FEATURES: • Base pedestal elbow (duct foot) • Threaded delivery counterflange • Top supports for guide tubes PATROL PM (single-phase) • Float switch. • 10m “H07 RN-F” submersible power cable with Schuko plug. • 1.1 to 1.5 kW models are supplied with control box with capacitor and manual reset motor protector. 2.2 kW models are supplied with control box type QES 300 MONO. PATROL P (three-phase) • 10m “H07 RN-F” neoprene power cable GUARANTEE 2 YEARS subject to our general terms of sale. CONSTRUCTION CHARACTERISTICS • PUMP BODY, MOTOR CASING AND BASE PEDESTAL: cast iron. • IMPELLER: single-channel, in cast iron. • BASE: stainless steel AISI 304. OPTIONS ON REQUEST ⇒control box for three-phase pumps ⇒dual voltage: 230/400 V or 400/690 V ⇒single-phase versions without float switch ⇒other voltages or frequency 60 Hz CONSTRUCTION AND SAFETY STANDARDS EN 60034-1 IEC 34-1 CEI 2-3 DIMENSIONS Typical installation a Guide tubes Ø external 27 mm maximum Ø internal 19.5÷21.5 mm w DN b g m d h c e n f 50 NOTE The features and specifications herein stated are in no way binding for the manufacturer . The manufacturer is free to modify the product at any time without previous notice. 51 Ufficio immagine & comunicazione cod. C104022006