EP Brochure 08062010.cdr

EP SERIES
SHINN SYSTEMS
Excavator Powered Cutting Attachments
EP-24-S
EP-36-S
EP-48-S
EP-60-EWC
Rec. Min.
Excavator
Cutting
Width
No. of
Teeth
Min.
H.P.
Max.
H.P.
Cutter
RPM
13 Ton
20 Ton
22 Ton
25 Ton
24”
36”
48”
60”
16
28
36
48
64
76
84
84
250
300
300
300
1780
1780
1780
1780
HIGH TORQUE CUTTER SYSTEM
HIGH HP RATED
SPECIFICATIONS
Recommended
Application
6-8” Trees/Brush
6-14” Trees/Brush
6-14” Trees/Brush
6-8” Trees/Brush
THE CUTTER HEAD DESIGNED TO MEET YOUR NEEDS NOW...AND IN THE FUTURE
Shinn Systems introduces the first excavator powered cutter head designed to handle
up to 300 HP. What does this mean for you?
-Performance-The EP-Series utilizes the most effective cutting teeth available.
On excavator powered units this is critical since you want to make the most of
the power you have available. Slice through wood instead of pounding it with
hammers. High torque means higher production-faster cutter recovery times.
-Heavy Duty Design-Constructed to handle up to 3X the power that a 30 ton
excavator can direct to the implement circuit.
-Expandability-Should your production needs increase, you can upgrade to 125
to 300 HP auxiliary power packs with the same cutter head!
The EP-Series, designed for productivity now, with an eye towards the future.
SHINN
SYSTEMS
THE INTELLIGENT APPLICATION OF POWER
EP-SERIES
BUILT TO PERFORM...BUILT TO LAST
Power Coupling-Absorbs
shock and protects motor
bearings.
Gates PolyChain GT2Long life, heavy duty Kevlar
strand belt drive. Rated to
300 HP.
High Torque Variable Displacement
MotorsMatched for optimum performance
to your specific excavator. Motor/
Hydraulic protection valving
included.
Mutilple Mount Options
Cutter head can be mounted in
line with stick for smaller brush
and sweeping, 90 degress to stick
to grind trees above 8” in diameter.
Extreme Efficiency Tri-Cutter Teeth
Sharp, high strength teeth slice
through the toughest wood. 3
cutting tips means that you can
rotate the teeth up to 3 times. Low
Cost-$16.50 each.
Heavy Duty Lower Drive
Massive spherical pillow blocks
with 3 5/8” diameter mainshaft
are driven by a Gates 125mm
wide PolyChain GT-2 sprocket.
Heavy Duty Pushbar
4 x 4 tubing or solid 3 7/16”
round stock pushbars for
maneuvering trees and debris.
AR-400 3/4” Sheild
AR-400 exhibits excellent
wear charactoristics and has
the same strenght as 1” A36
Debris Control System
Outer covers extend into
drum edge, reducing wire
ingestion and damage.
SHINN SYSTEMS, INC.
NORTH AMERICA
11717 REAMES ROAD
CHARLOTTE, NORTH CAROLINA 28269
1-877-942-4477
(704) 597-2005
(704) 597-2008 (FAX)
Publication Number EP03252011-1
Heavy Duty Upper DriveUtilizes jackshaft instead of
placing load on hydraulic motor
bearing. Heavier and more reliable
than overhung load adaptors
Heavy Duty Lower Covers
3/4” lower covers are strong
enough to support the weight
of the excavator
IMPORTANT: Shinn Systems reserves the
right to change these specifications without
notice and without incurring any obligation
pertaining to such change. Shinn Systems
does not warrant the safety or reliability of
components from other manufacturers.
SHINN
SYSTEMS
Visit Shinn Systems on the Web at
http://www.shinncutter.com
Printed in U.S.A.
c
2011 SHINN SYSTEMS, INC.
All Rights Reserved.