Section B - RSS Distributors

Transcription

2014 Party Products
Non-Food Service
RSS
DISTRIBUTORS
B
1
TABLE CLIPS
B-SNAP
T-SNAP
SKC-343
SKIRTING CLIPS
SKC-LTD
Snap-Drape
SKC-LT2
VELCRO TABLE CLIPS
• Clear polycarbonate clips with hook-side velcro
• SKC-343 clips snap onto 3/4" tables (also fits 5/8" tables with
crimped edges) and are 2.5" long
• SKC-MW multi-width clips fit tables from 1/2" to 1 1/2" in
thickness and are 1" wide
• SKC-LTD and SKC-LT2 clips are both intended for use on
Lifetime tables - see special note below
• 100 per bag, 500 per case
•
•
•
•
Extra clips for attaching Snap-Drape skirts
Clips attach directly to table over table-topper
Skirting header attaches directly to clips
Keeps skirting tight around corners for crisp,
clean appearance
• Sold in bags of 100 each
Snap Clips
• Fasten to grommets that are permanently attached to
the skirting header
#b-snap
#T-SNAP
SKC-MW
Fits 3/4" edge (RSS, Palmer-Snyder, McCourt) $31.25
Fits 5/8" table edge (Maywood)
31.25
#SKC-343
Tables to 3/4"
#SKC-MW
Tables to 1 1/2"
#SKC-LTD
Lifetime tables w/drop edges
#SKC-LT2
Lifetime tables w/2" thick edges
$30.80 Bag
138.60 Cs
36.00 Bag
162.00 Cs
43.25 Bag
194.60 Cs
43.45 Bag
195.50 Cs
Special Note: Lifetime tables can have either a drop edge (you can curl your
fingers under the edge of the table) or a 2" thick solid edge. Use the #SKCLTD clips for tables with the drop edge and the #SKC-LT2 clips for tables
with the 2" thick edge
AV-VELCRO
BV-VELCRO
DV-VELCRO
EV-VELCRO
HDC-341
fV-VELCRO
lV-VELCRO
HDC-341-NARROW
HDC-MW
TV-VELCRO
HDC-LT2
Tablecover Hold-Down Clips (no velcro)
Snug-TightTM (Velcro) Clips
• Hook-side fastener on face of clip attaches to
loop-side fastener sewn into skirting header
• All clips sold 100 per bag
#AV-VELCRO
#BV-VELCRO
#DV-VELCRO
#EV-VELCRO
#FV-VELCRO
#LV-VELCRO
#TV-VELCRO
TD
Fits 3/8" to 1/2" edge
$50.50
Fits 3/4" edge (RSS, Palmer-Snyder, McCourt) 50.50
Fits 1 1/8" to 1 1/2" edge tables
63.65
Fits drop-edge tables up to 2 3/4"
63.65
Fits aluminum tables and Bil-Jax staging
63.65
Fits Lifetime tables (2" thickness)
63.65
Fits 5/8" edge (Maywood)
50.50
Terms Discount Price - Where this symbol appears, the price (or
column of prices) to which it is attached reflects the net price to you
when the item is included on an order over $600, and you elect the 5%
20 terms offered on such orders (see "General Information"page).
• Snaps over plastic tablecovers to prevent blowing in wind
• HDC-341 clips are 1.5" wide and can be used on tables
from 1/2" to 3/4" thickness
• HDC-341-NARROW clips are a narrower (3/4") version of the HDC-341 clips
and are sold only in cases of 500 clips
• HDC-MW clips are 1" wide and can be used on tables
from 1/2" to 1 1/2" thickness
• HDC-LT2 clips are 1" wide and can be used on 2" thick tabletops
#HDC-341
Tables to 3/4"
#HDC-341-NARROW
Tables to 3/4"
#HDC-MW
Tables to 1 1/2"
#HDC-LT2
Lifetime tables w/2" thick edges
RD
$14.95 Bag (100)
67.25 Cs of 500
39.50 Cs of 500
22.20 Bag (100)
99.90 Cs of 500
34.60 Bag (100)
155.70 Cs of 500
Remember Discount - Indicates that the price of the item approaches
the $600 volume discount threshold. By adding enough items to the
order to reach that threshold, the 5% discount terms cited with the
"TD" description will apply to the entire order.
B
2
Party Products
Non-Food Service
RSS
2014
DISTRIBUTORS
TABLECLOTHS/NAPKINS-fabric
100% WOVEN POLYESTER FABRIC
•
•
•
•
Colorfast; highly stain resistant
Wrinkle resistant
Wash warm, dry low
Choose from dozens of colors - all the same price
Tablecovers
Round
WP Teal
Light Blue
Slate Blue
Periwinkle
Royal
Navy
Light Pink
Pink Balloon
Dusty Rose
WP Dusty
Mauve
Hot Pink
Fuchsia
Raspberry
Ruby
Cherry Red
Red
WP Sand
Burgundy
WP Burgundy
WP Lavender
Lilac
Antique Violet
Claret
Plum
Purple
Silver
WP Grey
Charcoal
Black
§Neon Yellow
§Neon Green
§Neon Orange
§Neon Pink
WP is woven polyester
- just like all of the other
shades.
It is used simply to distinguish a new set
of shades introduced by the manufacturer.
Woven Polyester
color swatch available
at www.rssd.com
White
Ivory
WP Beige
Tan
Camel
Café
Honey
Maize
WP Maize
Lemon
Goldenrod
Gold
Peach
WP Peach
Tigerlily
Coral
Orange
Burnt Orange
Terra Cotta
Copper
Brown
Seamist
WP Green
Mint
Lime
Kelly
Moss
Hunter
Forest
WP Sage
Light Olive
Dark Olive
Aqua
Turquoise
Jade
Teal
Cottunique® Fabric
• 100% Fortrel® polyester offering the
softness of cotton and the durability
of polyester
• Soft and pleasant to touch
• 85% as absorbent as 100% cotton
• 72% less shrinkage than 100%
cotton
• Excellent color retention
• Holds starch for napkin folds
• Wash warm, dry low
• Pricing is color dependent
White
Ivory
Orange
Burnt Orange
Terra Cotta
Tan
Camel
Diana Wheat
Nutmeg
Brown
Fudge
Maize
Lemon
Gold
Diana Gold
Mustard
Peach
Light Pink
Pink
Dusty
Hot Pink
Cherry Red
Red
Maroon
Burgundy
Aqua
Teal
Seamist
Diana Seamist
Light Blue
Hawaiian Blue
Royal
Navy
Honeydew
Lime
Loden
Hazel
Light Olive
Dark Olive
Hunter
#VIS70
#VIS90*
#VIS108*
#VIS120*
$9.70
12.15
$5.20 Ea
6.40 Ea
9.15 Ea
9.70 Ea
#VIS13SHIRR** 13' x 29" $47.95 Ea
#VIS21SHIRR** 21' x 29" 77.45 Ea
Trash Can Cover
#VIS55TC 55 Gal.
Elasticized
Instructions on how to size
your tablecloth available at
www.rssd.com
$15.95 Ea
§15% surcharge for Neon colors
Washing instructions for
all fabrics available at
www.rssd.com
Square
White
$15.80 28.50 42.50 49.20 Ivory Others
17.1517.15 28.5027.80
42.5039.15
49.2048.00
Ivory
23.70
49.40
Napkins per dz
#COT1717 17"x17"
#COT2020 20"x20"
#COT4545
45"
#COT5454
54"
#COT6060
60"
#COT7070
70"
White
$7.40 10.30 12.25 15.80 Ivory
7.95
10.95
12.50
17.15
Others
7.95 10.95
12.50
17.15
Skirting - Shirred
White
#COT60120 60"x120" $22.80 #COT90156* 90"x156" 49.40 To Order:
17" x 17"
20" x 20"
45"
54"
60"
70"
Skirting - Shirred
*Note: Sizes over 70" will have a seam
Oblong
Forest
Lilac
Cottunique color
Wisteria swatch available at
Periwinkle www.rssd.com
Antique Violet
Claret
Raspberry
Purple
Cottunique washing
instructions
Silver
available at
Black
www.rssd.com
Eggplant
Copper
#VIS4545
#VIS5454
#VIS6060
#VIS7070
$9.70 Ea
15.20 Ea
21.80 Ea
24.25 Ea
70"
90"
108"
120"
Napkins per dz
Round
#COT70
70"
#COT90* 90"
#COT108* 108"
#COT120* 120"
Square
Oblong
#VIS60120 60" x 120" $15.50 Ea
#VIS90156* 90" x 156" 27.30 Ea
#VIS1717
#VIS2020
Trash Can
Cover
Napkins
Skirting
White
$14.20
17.40
Others White 23.70 #COT13SHIRR** 13'x29" $56.10 48.30 #COT21SHIRR** 21'x29" 90.55 Ivory Others
14.95 14.95
18.00 18.00
Trash Can Cover
White
#COT55TC 55 Gal $18.95 Elasticized
Ivory Others
60.95 60.95
98.45 98.45
Ivory Others
20.90 20.90 *Note: Colors over 70" will have a seam; White & Ivory over 90" will have a seam
**Note: Skirting must be ordered in pairs for pricing to apply as indicated. When
ordered in odd numbers, including singles, one skirt will incur a 25% upcharge.
Plastic skirting clips for 3/4" tables are provided with each skirt. Larger clips
can be provided at a premium of $.55 per clip
Note: Only the most popular sizes are listed. However, all sizes are available.
Ask for a quotation.
(
Call: (800) 233-0175
Fax: (717) 892-5981
Web: www.rssd.com
Email: [email protected]
2014 Party Products
Non-Food Service
RSS
DISTRIBUTORS
B
3
TABLECLOTHS/TOPPERS/FABRIC
kENSINGTON DAMASK
Fabric: 50/50 Poly/Cotton 70" Wide
• Polyester and cotton combination offers the
perfect combination of absorbency, softness
and durability
• Permanent press characteristics
• Machine wash cool - 900, tumble dry low
• Soil resistant finish
poly cove lace
Fabric: 100% Polyester - 120" Wide
*Sizes over 70" will have a seam
Colors
White
Ivory
Wheat
Gold
Celadon
Hunter
Porcelain
Peach
Mauve
Burgundy
Aubergine
Federal Blue
Navy
Pewter
Black
Round
#KEN70
#KEN90*
#KEN108*
#KEN120*
• Cold water wash only - mild detergent
• Tumble dry cool
Kensington Damask
color swatch available
at www.rssd.com
$21.50 Ea
32.80 Ea
45.30 Ea
55.70 Ea
70"
90"
108"
120"
Round
#PCL70
#PCL90
#PCL108
#PCL120
$14.10 Ea
16.45 Ea
18.25 Ea
21.50 Ea
45"
54"
60"
70"
#KEN1717 17" x 17"
#KEN2020 20" x 20"
PCL1717
PCL2020
dazzle
Fabric: 75% Rayon/25% Polyester - 50" Wide
Turquoise-Gold
Cherry-Red
Sage-Maize
Teal-Black
Olive-Black
Black
Round
#DAZ70*
#DAZ90*
#DAZ108*
#DAZ120*
TD
Champagne-Gold
Orange-Gold
Royal-Black
Violet-Green
Copper-Black
Square
70"
90"
108"
120"
$25.40 Ea
40.95 Ea
67.75 Ea
79.95 Ea
#DAZ4545
#DAZ5454*
#DAZ6060*
#DAZ7070*
45"
54"
60"
70"
$12.55 Ea
20.10 Ea
22.15 Ea
28.15 Ea
#PCL4545
#PCL5454
#PCL6060
#PCL7070
45"
54"
60"
70"
$9.55 Ea
11.20 Ea
12.30 Ea
26.45 Ea
17" x 17" $19.15
20" x 20" 23.65
Instructions on how to size
your tablecloth available at
www.rssd.com
Dazzle color
swatch available
at www.rssd.com
Blush-Pink
Ruby-Aqua
Pink-Aqua
Burgundy-Black
Lemon-Lime
$26.45 Ea
34.40 Ea
42.10 Ea
47.00 Ea
**Note: Skirting must be ordered in pairs for pricing to apply
as indicated. When ordered in odd numbers,
including singles, one skirt will incur a 25% upcharge.
• A spectacular iridescent crinkled satin
• Two colors in cloth - shifts from one to
the other when seen from different angles
• Wash cold, mild detergent, no bleach
• Dry cool
Colors
70"
90"
108"
120"
Napkins per dz
$20.25
27.00
Square
Oblong
Skirting - Shirred
#PCL60120 60" x 120" $24.25 Ea #PCL13SHIRR**13' x 29"$87.75 Ea
#PCL90156 90" x 156" 58.45 Ea #PCL21SHIRR**21' x 29"141.75 Ea
Oblong
Skirting - Shirred
#KEN60120 60" x 120" $33.20 Ea #KEN90156*90" x 156" 58.50 Ea #KEN13SHIRR** 13' x 29" $86.15 Ea
#KEN21SHIRR** 21' x 29" 139.15 Ea
Napkins per dz
White
Ivory
Square
#KEN4545
#KEN5454
#KEN6060
#KEN7070
Colors
Taupe-Gold
Plum-Green
Burning Embers
Ivory
Silver
White
Note: Orders for Tablecloth
products are themselves
excepted from the standard
5% RSS volume discount,
but do count towards volume
qualification for other items
on the same order
Oblong
Skirting - Shirred
#DAZ60120* 60" x 120" $40.55 Ea #DAZ13SHIRR**13' x 29" $109.70 Ea
#DAZ90156* 90" x 156" 80.50 Ea #DAZ21SHIRR**21' x 29" 177.20 Ea
Napkins per dz
DAZ1717
17" x 17"
DAZ2020
RD
20" x 20"
$28.70
33.45
B
4
Party Products
Non-Food Service
RSS
2014
DISTRIBUTORS
table LEG WEDGES
TABLE NUMBERS AND CARD HOLDERS
TABLE NUMBER STANDS
RSS
4
• Two styles available; chrome - plated
w/double ring clip on 3" base and stainless
steel rod with harp clip on extra heavy cast base
• Available in heights as indicated below
HCC-12
#HCC-xx
Chrome-plated
#DCH-xx
Stainless steel
DCH-12
18" height
$29.90 Dz
N/A
12" height
$23.65 Dz
67.20 Dz
#EZ-LEVEL-CLEAR
TABLE LEG WEDGES
RSS
TABLE NUMBERS
RSS
• Stabilize tables, chairs, appliances, etc. quickly and easily with these
wedges
• Strong and durable - constructed from highest quality resin
• Stackable to fill larger gaps
• Sold in packages of 50 each
• Large 4" square plastic cards with
rounded corners
• Printed on both sides
• Sold in sets as follows:
DLR:$12.50 Pk
#4-1-50Numbers 1-50
$5.35 Set
#4-1-100Numbers 1-100 11.15 Set
#4-51-100Numbers 51-100 5.20 Set Closeout
VELCRO TAPE
CHAIR FEET & TABLE RISERS
VELCRO TAPE
RSS
• Pressure-sensitive tape, hook side only,
for mounting velcro-backed skirting to table
or stage edges
• Corresponding loop side only tape also
available for making other attachments
• Available in both 1" and 1.5" widths
• Sold in rolls of 25 yards each
#100WP50
#101WP50
#120WP50
#121WP50
Hook Side Only, 1"
Loop Side Only, 1"
Hook Side Only, 1.5"
Loop Side Only, 1.5"
CHAIR FEET
Note: Beige matches
McCourt
Chairs only.
$17.95 Roll
17.95 Roll
26.65 Roll
26.65 Roll
• Velcro roll goods without adhesive backing, intended for sew-on applications
• Width: 1"
• Sold in rolls of 50 yards each
$20.60 Roll
20.60 Roll
31.50 Roll
31.50 Roll
To Order:
Color
Beige
Black
White
DLR
$.30 Ea
.30 Ea
.30 Ea
RSS
RSS
Hook Side Only, 1"
Loop Side Only, 1"
Hook Side Only, 1.5"
Loop Side Only, 1.5"
Part#
#01410
#01420
#01430
#10RISER
TABLE RISERS
VELCRO BACKING, SEW-ON
#T100W
#T101W
#T120W
#T121W
• 3/4" Size
• Fits Samsonite, McCourt and
Palmer Snyder chairs
(
• Convert any table with
standard 24" wide legs
from sitting to standing height
• Adds 10" to height of table
DLR:
$79.95 Pr
Call: (800) 233-0175
Fax: (717) 892-5981
Web: www.rssd.com
2014 Party Products
Non-Food Service
RSS
DISTRIBUTORS
B
5
tables
PLYWOOD PEDESTAL
TABLES
FOLDING TABLES, PLYWOOD
RSS
In Stock
At
RSS
RSS
In
Stock
At
RSS
• Tabletops are 3/4" exterior quality plywood
• Bullnose edging stapled to all perimeter edges
• Polyurethane applied to both top (3 coats)
and underside (2 coats) of tabletop
• Folding and locking legs are 16 gauge 1" tubing
• Leg stoppers internally fitted - cannot come out
• Brown powder coating applied to folding legs
• Solid wood runners on underside of tabletop provide
for easy stacking of tables
• Warranty: 12 months
• Available from RSS warehouse as follows:
Part#
#OB-FT1896
#OB-FT3048
#OB-FT3072
#OB-FT3096
#OB-FT48
#OB-FT60
#OB-FT66
#OB-FT72
• Tabletops are 3/4" exterior quality plywood
• Bullnose edging stapled to perimeter of table
• Polyurethane applied to both top (3 coats) and underside (2 coats) of
tabletop
• Cast aluminum four-leg pedestal base (27 1/2" wide) supports table top on
a steel center column
• Table includes two center columns, one to provide a sitting height of 30"
and the second to provide a standing height of 42"
• Center columns measure 1 5/8" (42mm) middle diameter (non-standard)
• Cast aluminum center column flange attached to underside of table using
bolt-through construction to ensure sturdiness and long-life
• Available in 24", 30" and 36" tabletop diameters
• Warranty: 1 year
Dlr
$61.50
54.50
61.50
74.60
59.20
81.25
94.50
109.95
Description
Weight
Classroom Table, 18" x 96"
Banquet Table, 30" x 48"
36 lbs
51 lbs
62 lbs
Banquet Round Table, 48"
39 lbs
65 lbs
68 lbs
90 lbs
Part#
#OB-PT24
#OB-PT30
#OB-PT36
Note: The following wooden pallet charges will be added to the freight
costs for orders of five or fewer tables of any size
6' Rounds - $40.00
Banquets - $20.00
5' Rounds - $34.00
4' Rounds - $26.00
Description
Pedestal Table, 24" Diameter
Dlr
$58.40
64.95
70.20
Note: Orders for all products on this page are themselves excepted from the standard 5% RSS volume discount, but do count towards
volume qualification for other items on the same order
Training
Table
Gaming
Table
SPECIALTY PLYWOOD TABLES
PS Furniture
• Folding plywood tables in several styles: training, square,
serpentine and gaming
• All table tops constructed from 3/4" plywood sealed with
walnut stain and UV polycoat
• Solid American hardwood runners secured with 100% boltthrough construction
• Black vinyl "bullnose T" edging on all table edges
• Heavy-duty "wishbone" style folding legs on training, square
and serpentine tables
• Heavy-duty "card table" style folding legs on gaming tables
• All tables 30" in height
• Minimum order: 2 each (same size)
TD
Serpentine
Table
Serpentine Table
Measuring Chart
at rssd.com
Part#
Description
DLR
#SM1872
#SM1896
#BQ4848
#BQ6060
#BQ7272
#SP3X8
#SP4X9
#SP5X10
#SP7X12
#BQ3232
#BQ3636
Training Table, 18" x 72"
Training Table, 18" x 96"
Square Table, 48" x 48"
Serpentine Table, 3' D (inner edge) x 8' D (outer edge)
Gaming Table, 32" x 32"
Gaming Table, 36" x 36"
$98.00
103.00
115.00
145.00
216.00
108.00
124.00
139.00
216.00
98.00
108.00
RD
B
6
Party Products
Non-Food Service
RSS
2014
DISTRIBUTORS
harvest table
WOODEN HARVEST TABLE & BENCH
RSS
• Authentic-looking wooden harvest tables and matching benches for use at outdoor events
• Tabletop constructed from 3/4" knotty pine plywood; side trim is 3/4" #2 pine planking
• Tabletop and sides center-stabilized with 2" x 4" fir cross bracing
• Legs constructed from 4" x 4" fir post stock
• Legs seat firmly into 5" deep metal bracket and lock positively in place
• Table legs can be easily removed for storage and transport
• Bench legs are permanently attached
• Finish is stain with one coat of polyurethane - also available unfinished
• Available finishes: Antique (light) Walnut (WL), Dark Walnut (DW)
Item #
Description
Dimensions
Weight
#HARTAB8-xx
Harvest Table, 8' Finished
40”W x 96”L x 30”H
104 lbs
#HARTAB8-UF
Harvest Table, 8' Unfinished
40”W x 96”L x 30”H
104 lbs #HARTAB6-xx
Harvest Table, 6' Finished
40”W x 72”L x 30”H
83 lbs
#HARTAB6-UF
Harvest Table, 6' Unfinished
40”W x 72”L x 30”H
83 lbs #HARBEN8-xx
Harvest Bench, 8' Finished
13”W x 96”L x 18”H
52 lbs
#HARBEN8-UF
Harvest Bench, 8' Unfinished
13”W x 96”L x 18”H
52 lbs
#HARBEN6-xx
Harvest Bench, 6' Finished
13”W x 72”L x 18”H
42 lbs
#HARBEN6-UF
Harvest Bench, 6' Unfinished
13”W x 72”L x 18”H
42 lbs
RD
DLR
$528.00
493.00
479.00
458.00
221.00
203.00
199.90
182.00
Folding chairs
EventXpress
EVENTXPRESS FOLDING
™
CHAIRS
PS Furniture
Powder-Coated Steel Frame
Standard Folding Chair
•
•
•
•
•
•
•
•
•
•
•
The ultimate choice for multi-purpose seating
Tubular steel construction - 18 gauge for superior strength
Oversized rivets for strong and secure pivot points
Back of plastic seat wraps around metal frame for clean look
New SecureCap chair feet won't fall off
Frame can be powder-coated steel or chrome-plated steel
Seat and back available in several colors
Seat dimensions: 15.5" W x 15.75" D x 17.1" H
Overall dimensions: 17.5" W x 16.75" D x 31.5" H
Warranty: One year limited
Chairs available as follows
*Note:
#C600WWH-WH
#C600CWH-WH
#C600BNE-NE
#C600BRW-NE
#C600BRW-BZ
#C600SBL-GR
#C600MGR-GR
#C600BLK-BL
Wedding White on White
Classic White on White
Bone on Neutral
Brown on Neutral
Brown on Bronze
Slate Blue on Gray
Medium Gray on Gray
Black on Black
DLR: $13.80 Ea (24-198)*
13.39 Ea (204+)*
Order quantities must be in multiples of 6 chairs with a minimum of 24
Note: Orders for PS Furniture products are themselves exempted from the standard 5% RSS volume discount, but do count
towards volume qualification for other items on the same order.
To Order:
(
Call: (800) 233-0175
Fax: (717) 892-5981
Web: www.rssd.com
2014 Party Products
Non-Food Service
RSS
DISTRIBUTORS
B
7
CHAIR DOLLY
ALL TERRAIN CHAIR DOLLY
PS Furniture
The Dolly
•
•
•
•
•
•
•
•
•
Specially designed dolly for moving folding chairs over rough terrain
Lower frame and handle construction is welded steel
Upper frame is .145" anodized aluminum; chair stack glides are 60" long and 18" apart
Steel frame parts are powder-coated "smooth black"
Dolly features four 10" x 3" solid urethane wheels, each with two ball bearings
Forks are 28" long (26" usable) and are spaced 16" apart
Cart capacity: 50 PS polyfold chairs
25 PS white resin chairs
Other chairs with stacking widths between 15" and 18"
Weight capacity: 500 lbs
Warranty: 3 years limited
The Pallets
• Thermoformed .150" thick ABS plastic, black
• Pallet tray is 1" deep - contains first chair
• Overall dimensions: 20" x 40" (approximate)
The Cover
• Gray nylon fabric w/double-stitched seams
• Fits over entire pallet, 42" zipper one end
• Plastic "Fastec" clip runs completely around bottom to secure cover
Warning: Chairs must
be securely strapped to
pallet for transport over
rough terrain
Note: Orders for chair dollies are themselves excepted from the
standard 5% RSS volume discount,
but do count towards volume
qualifications for other items on the
same order.
#HD-ATCD
All Terrain Chair Dolly
#C600-PALLET Plastic Pallet, Series 600 PS Folding Chairs
#C600-COVERNylon Cover, Loaded Pallets, C600 Chairs
#C450-PALLET Plastic Pallet, PS White Resin Chairs #C450-COVERNylon Cover, Loaded Pallets, C450 Chairs
#BSGDOL
DOLLY, FOLDING CHAIRS
RSS International
$544.10
50.65
67.50
50.65
67.50
high chairs
#HCW-1KD
WOODEN
HIGH CHAIR
RSS
• Sturdy chair dolly holds folding chairs in stacked position
• Accommodates Gladiator, Palmer Snyder C600 Series,
Samsonite 2200 Series and many other brands
• All-steel construction w/powder coat finish
• Stacking rim of tray is lightly covered with
carpet to prevent scratching of chairs
• Chair tray is 41" L x 20"W with 3 1/2" W
stacking rim and 1" H lip
• Handle: 38" H
• Casters: 5" rubber (2 swivel)
• Weight: 32.25 lbs
DLR:
TD
• Solid, hardwood construction
with natural finish
• Glued joints with screws for
added strength and durability
• Space saving stacking design
• Weight: 13 lbs. each
• Shipped knock-down (KD)
style
DLR:$37.95 Ea
$89.75 Ea
RD
B
8
Party Products
Non-Food Service
RSS
2014
DISTRIBUTORS
PATIo umbrellas
•
PATIO UMBRELLAS
#UT-PGUIDE
UMBRELLA TABLE POLE GUIDE
Frankford Umbrella
Under The Table
• 7 1/2' conventional style vinyl top w/white canvas binding
• Two-piece polished aluminum center pole with standard tilt
mechanism and manual lift, 1.5" diameter
• Heavy-duty chrome-plated steel eight-rib support for vinyl top
• Note: Vinyl tops are heavy-duty triple laminate blockout
• Brass Grommet (#8 2-piece) secures top of cover
• Stainless steel joints and joint rivets
• Spring-activated steel ledge supports umbrella when open
• Purchase base separately (#32BASE-PLST)
• Product provides stability for umbrellas inserted into wooden umbrella
tables without use of umbrella base
• Drill 1 1/2" diameter hole in center of table
• Permanently install metal flange on underside of table using three
"through table" bolts (provided)
• When setting up for an event, simply snap pole guide into flange on
under side of table and insert umbrella pole through top side of table
• When event is over, remove umbrella from pole and unsnap pole guide
from underside - table then folds normally for storage
#75PATIO-WH
#75PATIO-YW
#75PATIO-RW
All White
Yellow & White
Red & White
DLR
$89.95
89.95
89.95
TD
DLR:
$34.95 Ea
$85.45
85.45
85.45
umbrella bag
BISTRO CHAIRS
MIAMI BISTRO
Grosfillex
#75PATIO-BAG
UMBRELLA BAG,
PATIO UMBRELLAS
Frankford Umbrella
• Constructed from 100% prime synthetic resin
• U.V. stabilized
• High contoured and flexible back joins with shaped seat for
optimum comfort
• Glossy and matte alternating stripes enhance design of seat
• Stacks easily, nests closely
• Easy to maintain - just wet sponge with mild liquid detergent
• Extremely durable - 3 year warranty
• Dimensions: 17"W x 20"D x 35"H
Note: White chairs are sold
at best price in any quantity.
For best price on colored
Part#
Color
DLR
chairs, order in multiples of
#49-0550-04 White
$18.50
$17.58
32. To order colored chairs
#49-0550-78 Amazon Green 19.90
18.91
in multiples of 4, add $5.70
#49-0550-17 Black
19.90
18.91
each to best prices.e
#49-0550-02 Charcoal
22.75
21.61
To Order:
(
• Heavy blue canvas umbrella
bag with drawstring
• Sized for standard 7 1/2 foot
patio umbrellas
• Includes interior pocket for
bottom pole of umbrella
• Includes shoulder strap style
carrying handle
DLR:
Call: (800) 233-0175
Fax: (717) 892-5981
Web: www.rssd.com
$14.40 Ea
Available
Late
May!
2014 Party Products
Non-Food Service
RSS
DISTRIBUTORS
B
9
Available
MARKET UMBRELLAS
Late
May!
#854WM-WH
MARKET UMBRELLA, 9' WHITE
Frankford Umbrella
• Top quality wooden market umbrella in 9' size
• Excellent quality hardwood frame, 1 1/8" x 3/4" w/brass fittings
• Cover manufactured from heavy polyester fabric with extra coat of
polyurethane to minimize decomposition
• Cover is water-repellent and fire-resistant
• Cover fitted with vanes to reduce wind lift effects
• Two-piece centerpole, 1 1/2" diameter
• Heavy resin runner and notch secure umbrella in open position
• Heavy gauge rope pulley and pulley wheels ease task of opening umbrella
• Non-tilting
• Purchase base separately below (#91958)
Market Umbrella w/#91958 Base
DLR:
$129.95 Ea RD
Caution: While these umbrellas are a top quality product, their wooden
structure makes them vulnerable to damage from abuse and from high
winds. Always leave in down position when unattended
TABLE AND CHAIR ACCESSORIES
#32BASE-PLST-2
PATIO UMBRELLA BASE
Grosfillex
• High-impact white plastic base
• Can be filled with 35 lbs. of
sand or stone
• Heavy set screw clamps onto
umbrella pole
DLR: $17.75
CAUTION: For liability reasons, umbrellas should only be
rented and installed with a 40"
minimum size table and a 30
lb. base (patio umbrellas) or 70
lb base (market umbrellas)
TD
#502A
ALUMINUM UMBRELLA BASE
Frankford Umbrellas
• Aluminum shell umbrella base
• Ships empty
• Fill with sand or gravel (water is not
recommended)
• Weighs 50 lbs when filled
• Recommended for use with market
umbrella with a table (not freestanding)
• Diameter: 19"
• Height: 6 1/2"
DLR: $35.75
#RB90W
HEAVY-DUTY RESIN
UMBRELLA BASE
Fiberbuilt
• White resin umbrella base
• Ships empty
• Fill with sand or gravel (water is not
recommended)
• Weighs 90 lbs when filled
• Recommended for use with market umbrella
(can be used freestanding)
• Dimensions: 22" D x 12"
• Sleeve accommodates up to 2" pole
• Includes molded handle and roller (not for
wheeling with umbrella in base)
DLR: $106.00
RD
B
10
Party Products
Non-Food Service
RSS
2014
DISTRIBUTORS
ALL WEATHER stackable BAR STOOLS
#DV949A
ABRI BAR STOOL
RSS
RSS
RSS
• Chair frame is cast iron
• Seat and back are powder-coated micro
mesh construction
• Classic wrought iron look
• Anthracite finish
• Overall height: 42.5"
• Seat height: 31"
• Seat: 15" W x 15" D
• Stackable
• Warranty: 2 years
DLR
#DV380TS
TARA X BAR STOOL
#DV550TS
SOUTH BEACH BAR STOOL
$102.60 Ea
97.47 TD
•
•
•
•
•
•
•
Construction is powder-coated aluminum
Titanium silver finish
Overall height: 39.5"
Seat height: 30"
Seat: 13" x 16 3/4"
Stackable
Warranty: 2 years
DLR
•
•
•
•
•
•
•
•
Chair frame is powder-coated tubular steel
Seat and back are powder-coated steel
Titanium silver finish
Overall height: 40.5"
Seat height: 31"
Seat: 16" x 16"
Stackable
Warranty: 2 years
DLR
$132.00 Ea
125.40 TD
$94.80 Ea
90.06 TD
portable fencing
PORTABLE PVC FENCING
Signature Fencing
•
•
•
•
•
•
•
Picket Style
Traditional Style
Top Inset
Display Style
Lattice Style
Leg Inset
To Order:
Classic white, expertly crafted fencing panels are appealing from all points of view
Available in four styles shown at left
All panels are preassembled
No tools required for setup or for tear down
Legs swivel out for setup and in for flat storage of panels
Pre-drilled holes in legs allow staking for increased stability
Decorative caps are attached and conceal shock-cord connectors for firmly attaching
panels in any of three directions
• Panels never need painting and will not rot, rust, warp or corrode
• High impact modifiers and superior UV inhibitors increase longevity
• Clean with common household cleaners
• Use 11" x 17" transparency for easy-to-produce signage on display panels
• All panels produced in 6' lengths
• Warranty: 3 years
Part#
Panel Style
Height DLR
#SP01
#SP02
#SP03
#SP04
#SP05
#SP06
#SP07
(
Traditional
Picket
Display
Traditional
Picket
Lattice
Lattice
42"
42"
42"
32"
32'
42"
32"
$106.90
112.25
135.45
102.70 RD
106.70
109.50
103.50
Call: (800) 233-0175
Fax: (717) 892-5981
Web: www.rssd.com
2014 Party Products
Non-Food Service
RSS
DISTRIBUTORS
B
11
TENT TIE-DOWNS
POLYPROPYLENE
TENT ROPE
Aamstrand Ropes
TENT TIEDOWNS
Are
You Still
Using Rope?
SpanSet
• With web ratchet assemblies, anyone can apply the precise amount of
tension on each tent stake quickly and safely
• Tent manufacturers and users are rapidly switching to Poly-Web Ratchet
Assemblies for securing tents
• Standard ratchet tiedown has a large twisted snap hook on one end and
D-ring on the other end
• Minimum breaking strength is rated at 10,000 lbs
• All tent tiedowns have twisted snap hooks
• Color: White
Part No.
#10R8DRTSPW
#10R12DRTSPW
#10R15DRTSPW
Size 2" x 8'
2" x 12'
2" x 15'
DLR
$15.65
17.35
17.65
• 3-strand twisted synthetic rope
• Used extensively for most rope requirements,
including tent/canopy replacement rope
• Very good strength and working load characteristics
• Resists abrasion, rot, mildew, oil, gasoline and most
chemicals
• UV inhibitor reduces deterioration due to sunlight
exposure
• Floats
• Sold on reels only in following four sizes:
Part#
Dia Lngth
#AAM-10052 1/4" 1200'
#AAM-10141 3/8" 600'
#AAM-10251 1/2" 600'
#AAM-10347 5/8" 600'
Breaking
Strength
1,238 lbs
2,673 lbs
4,158 lbs
6,138 lbs
Working
Load
155 lbs
334 lbs
520 lbs
767 lbs
White
DLR.
Reel
$34.10
38.75
67.65
99.50
power distribution and CABLE TIES
OUTDOOR EXTENSION
CORDS, WHITE
#D12420050
MULTI-OUTLET EXTENSION
CORD
DLR: $84.20
•
•
•
•
•
RSS
12/3 multi-outlet extension cord
Rated at 15A, 600V
Five covered outlets spaced 10' apart on 50' cord
Water and flame resistant
White
•
•
•
•
CABLE TIES
RSS
•
•
•
•
Standard natural (tends toward white) zip-lock cable ties
Both 50 lb and 250 lb tensile strengths available
Tie width: 3/16"
Available in three sizes as follows
Tensile Strength: 50 lbs
Part No.
Length
Quantity
DLR
#CT-6-50-N-1000
#CT-11-50-N-1000
#CT-14-50-N-1000
6 1/2"
11"
14"
1000/Bag
1000/Bag
1000/Bag
$21.90
29.95
45.75
Length
Quantity
DLR
11"
100/Bag
$49.50
Tensile Strength: 250 lbs
Part No.
#CT-14-250-N-100
TD
White extension cords for tent and party applications
12 gauge, 3 wire (12/3) and 10 gauge, 3 wire (10/3)
Type: SJTW, UL listed
Available in sizes as follows
#14025W
#14050W
#14000W
#10-3WH-50
12/3, 25' cord $22.25 Ea
12/3, 50' cord
42.95 Ea
12/3, 100' cord 84.40 Ea
10/3, 50' cord
76.20 Ea
#836Z
TRI-TAP ADAPTER
RSS
• Three-outlet adapter for extension cords
• UL listed - outside use
• White
DLR:$4.50 Ea
RD
B
12
Party Products
Non-Food Service
RSS
2014
DISTRIBUTORS
FRAME TENTS
FRAME TENT PRODUCTS
Norfolk Tent Company
FRAME TENTS
Norfolk Tent Company
•
•
•
•
•
•
•
•
•
•
•
Perfect for everyday use, the Flex Frame Tent is rugged, attractive and a snap to assemble
Frame components are 2" x 1/8" structural anodized aluminum, color-coded to differentiate between perimeter and roof support pipes
Fittings are 2" schedule 40 structural steel w/powder coated finish and featuring push-button assembly
Legs are standard 7' height and are fitted with bases; adjustable legs (7' - 8.5') are available as an option
Tent tops made from first-quality 14 oz vinyl fabric specifically manufactured for tent applications - both translucent and blockout materials available
All fabrics meet both federal and state fire regulations and are mildew and UV resistant
Tops are R.F. welded to eliminate needle holes and make completely water proof
Tops fasten to frame with non-rusting delrin buckles at two places on each of the straps - reduces potential for water pocketing
Tops reinforced with leather patches at corners and double layers at all rides and buckle bands
Separate carry bags provided with each tent for each type of frame component, for the top and for the fittings and safety caps
Complete tent packages and/or replacement tops available in three sizes as follows:
Frame Tent Packages (Specify Translucent or Blackout)
DLR
#FTPKG-1010
#FTPKG-1515
#FTPKG-2020
#FTALEG-4
#FTALEG-8
Tent Package, 10' x 10', White
Adjustable Leg Option, 4-Leg Tents
Adjustable Leg Option, 8-Leg Tents
$1,174.90
1,499.90
2,426.00
137.00
274.00
TD
$1,116.16
1,424.91
2,304.70
130.15
260.30
Note: Larger size "Flex-Frame" tents also available - please call for a quote
Replacement Tops (Specify Translucent or Blackout)
#FTTOP-1010
#FTTOP-1515
#FTTOP-2020
Replacement Top, 10' x 10', White
$432.20
621.20
844.40
TD
$410.59
590.14
802.18
Tent Sidewalls
• Sidewalls constructed from same first quality vinyl fabric as tent tops
• Available in both translucent white and premium materials (Picture Window, Mesh,
Insect Screen and Blockout)
• Cathedral windows can be added to either translucent or blockout sidewalls
Translucent White Sidewalls
#FTSW-720-SS
#FTSW-730-SS
#FTSW-740-SS
#FTSW-820-SS
#FTSW-830-SS
#CATHW-OP
Standard Sidewall, 7' x 20' $136.00
Standard Sidewall, 7' x 30' 183.50
Standard Sidewall, 8' x 30" 216.60
Cathedral Window Option
44.20
TD
$129.20
174.33
213.18
154.38
205.77
41.99
Premium Sidewalls (Blockout, Picture Window, Mesh, Insect
Screen)
#FTSW-720-PW
#FTSW-730-PW
#FTSW-820-PW
#FTSW-830-PW
Premium Material, 7' x 20' $148.00
Premium Material, 7' x 30' 200.00
To Order:
$140.60
190.00
169.10
226.77
(
REPLACEMENT PARTS, FRAME
AND FITTINGS
• Complete set of frame and fitting parts available
as follows
#FTPIPE-BR*
#FTPIPE-RD
#FTPIPE-BL
#FTPIPE-GR
#FTLEG
#FTLEG-ADJ*
#FTFIT-CORN
#FTFIT-TEE
#FTFIT-4CRN #FTFIT-8CRN
Brown Frame Pipe, 6' 10"
Red Frame Pipe, 9' 4"
Blue Frame Pipe, 10' 7"
Green Frame Pipe, 14' 5"
Standard Leg w/Base
Adjustable Leg Fitting
Corner Fitting
Side Tee Fitting
Crown Fitting, 4-Way
Crown Fitting, 8-Way
DLR
$34.20
46.40
50.80
68.50
47.50
34.20
59.60
47.50
57.50
99.50
*Note: An adjustable leg is comprised of a #FTPIPE-BR
Brown Frame Pipe plus a #FTLEG-ADJ
Adjustable Leg Fitting
RAIN GUTTER
• To abutt two tents to form a larger structure, use a rain
gutter to keep moisture from entering the seam
#FTRGUT
Rain gutter, per foot
Call: (800) 233-0175
Fax: (717) 892-5981
Web: www.rssd.com
$4.78 Ft
2014 Party Products
Non-Food Service
RSS
DISTRIBUTORS
B
13
POPUP TENTS
EZ-LIFT POPUP TENTS
Frankford Umbrellas
• Heavy-duty popup tents designed for commercial applications
• Non-rusting all aluminum frame w/1 1/2" square tubular legs
• Heavy 600 x 600 denier polyester fabric provides 99% UV protection
• Fire retardant and water repellant, CPAI-84 rated
• Colorfast fabric will not yellow
• Heavy gauge resin runners and foot pads
• Stainless steel positioning buttons
• Size: 10' x 10' w/four-position height adjustment (72" to 84" to bottom of valence)
• Tent package includes stakes, guy wires and carry bag
• Sidewall sets available; set consists of four solid panels with zipper in middle of panel - for
opening, tie sidewall to corner post
• All sidewall panels velcro to top of tent
• Replacement tent frames and tent tops also available separately
Part No
DLR
Description
#EZ-TENT
Complete Tent Package, 10' x 10' White
#EZ-TENT-SIDE Sidewall Set (4 panels)
#EZ-TENT-FRAME Replacement Frame Only, 10' x 10'
#EZ-TENT-TOP
Replacement Tent Top Only, 10' x 10' White
#EZ-TENT-BAG
Replacement Carry Bag
$314.00
214.90
212.50 RD
101.50
37.50
Note: Replacement frames, tops and sidewalls are sized for the Frankford 10' x 10' popup
tent. They may not fit other brands.
tent stakes and accessories
#218D-226C
STAKE DRIVERS
Pioneer Tool & Forge
#2518B
#2624WHSH
• 1 1/8" x 6" notched shank w/collar,
fits:
Bosch: 11304
Wacker: BH23, EH23
Kango: 2500
Hitachi: H65, H85, H90SB
• 2 1/2" inside diameter driver head
• Sold as set (shank plus head)
#2830WH
#2840DH
#PI-208
STAKE caps
All stakes constructed from bend-resistant Alloy steel
Stakes are shot-blasted for consistent finish
Made in ISO 9001:2000 compliant manufacturing facility
All stakes guaranteed against defects in material and workmanship
Part#
#2518B
#2624WHSH
#2830WH
#2840DH
TD
Description
Weight
Hook stake, 5/8" x 18"
1.70
Headed hook stake, 3/4" x 24"
3.50
Single head stake, 1" x 30" w/2" head
6.69
Double head stake, 1" x 40" w/2" heads 9.37
• Simple lever action removes all
types of stakes
• Easy to operate
• Fast and efficient
• Weight: 37 lbs
DLR:$185.00 Ea
DLR:$132.00 Set
TENT STAKES
•
•
•
•
#PI-230
STAKE PULLER
DLR
$5.60 Ea
11.05 Ea
11.95 Ea
15.65 Ea
• White plastic protective caps
fit stake heads from 1" to 2 1/4"
diameter
DLR: Call For Pricing
And Availability
RD
#PI-204243
STAKE BAR
• Stake bar w/3 holes
• Length: 24"
DLR:$20.00 Ea
Party Products
Non-Food Service
B
14
RSS
2014
DISTRIBUTORS
STANCHIONS
PLASTIC CHAIN
PLASTIC STANCHIONS
Mr. Chain
Mr. Chain
•
•
•
•
•
Available in white or black
1.5" or 2" L x .755" W x .210" thick
Made of high density polyethylene
Available in reels or cut length
Use suffix xx (WH) for white or xx (BK) for black
MC-301-xx
MC-501-xx
• Pole diameter: 2.5'
• Base diameter: 14"
• Assembled stanchion weighs 2.5 lbs or 6.5 lbs when base is
filled with sand
• Overall height: 40"
• Made from high density polyethylene containing UV inhibitors,
fade resistant, rustproof and will not require painting
• C-Hooks included
• Made in USA
1.5" Chain 200' Reel
1.5" Chain, cut to order
2" Chain, 125' Reel
2" Chain 125', cut to order
S-Hooks
$123.65 Reel
.75 Ft
89.65 Reel
.82Ft
Master Links
MC-307xx-12
MC-507xx-12
MC-303xx-12
MC-503xx-12
MC-902xx-12
1.5" Master Links, 12 per bag
2" Master Links, 12 per bag
1.5" S-Hooks, 12 per bag
2" S-Hooks, 12 per bag
C-Hooks, 12 per bag
$29.95 Ea
METAL STANCHIONS
RSS
• Classic portable metal stanchion w/matching
traditional base in polished stainless steel finish
• 37-1/2" H, tube diameter 2", base diameter 12"
• Handrail rope available in two lengths - 5' and 8'
• Rope diameter is 1-1/4"
• Velour ropes are red (RR), black (B) or burgundy (BR) with polished
stainless steel hooks
Part#
#90-5118
#90-5144xx-5
#90-5144xx-8
#90-5118-HWARE
#90-5144-HOOK
Description
DLR
Handrail stanchion, polished stainless steel finish $43.50 Ea
Handrail rope, 5' w/polished stainless steel hooks
12.65 Ea
Handrail rope, 8' w/polished stainless steel hooks 20.20 Ea
Hardware set only, bolt and washer for base
1.50 Set
Rope hooks only, polished stainless steel
1.50 Ea
Note: When ordering, substitute two-character color code for "xx"
To Order:
C-Hooks
DLR.
#MC-964-WH (White)
#MC-964-BK (Black)
DLR:
DLR.
(
Call: (800) 233-0175
Fax: (717) 892-5981
Web: www.rssd.com
$3.75
5.50
3.75
5.50
20.15
2014 Party Products
Non-Food Service
RSS
DISTRIBUTORS
B
15
STANCHIONS
#RSRTBL
#RSSIGNLSPS
#RSRTGY
METAL STANCHIONS WITH RETRACTABLE TAPE
American Metalcraft
•
•
•
•
•
•
•
Stanchions avalable with Black Matte or Brushed Stainless Steel poles and bases
Retractable tape extends to 84"
Suitable for indoor and outdoor use
Dimensions: 40" H w/15" diameter base
Wall-mount barrier housing is 8" high and extends 84"
Includes all hardware needed to attach to two walls
Optional two-sided sign holder slides over post
top for easy signage
• Sign holder dimensions: 8 1/2" x 11" satin stainless steel
• Available as follows
Storage Side
Connect Side
#RSRTWMRVSRD
DLR
Part#
Description
#RSRTBL
#RSRTBK
#RSRTGY
#RSRTRD
#RSRTWMRVSRD
#RSRTWMRVSGY
#RSSIGNLSPS
Black Matte stanchion w/black retactable tape
Brushed Stainless stanchion w/black retractable tape
Brushed Stainless stanchion w/grey retractable tape
Brushed Stainless stanchion w/red retractable tape
Wall-mount Brushed Stainless barrier w/red tape
Wall-mount Brushed Stainless barrier w/grey tape
Satin Finish Stainless two-sided sign holder
$120.90 Ea
120.90 Ea
120.90 Ea
120.90 Ea
79.00 Ea
79.00 Ea
44.95 Ea
ROTOMOLDED STANCHION
Meese Orbitron Dunne
• Upscale stanchion designed for use with plastic chain
or other decorative barrier
• Optional planter top available for stanchion - fits onto
top of stanchion in place of ball top
• Made by makers of rotomolded columns, urns/etc.
shown on pages B20-23
• Stanchion is 40" high x 4" in diameter with a 16"
square base
• White only
#ARM-340
#ARM-342
TD
RD
Stanchion w/ball top
Planter top for stanchion
$86.45 Ea
47.35 Ea
B
16
Party Products
Non-Food Service
RSS
2014
DISTRIBUTORS
SPECIAL OCCASION CANDELABRA
#FC-15SP-BR
SPIRAL CANDELABRA
• 15 light floor model - available in Traditional and Teardrop styles only
• Height adjustable
#UC-3-yy-xx
CONVERTIBLE UNITY
CANDELABRA
Part#
Description
DLR
#FC-15SP-yy-xx 15-Lite Spiral Std/TD $269.99 Ea
#FC-15FA-TD-BR
TREE CANDELABRA
•
•
•
•
5, 9, and 13 light floor models
arranged in a tree configuration
Height adjustable
Remove top from stand for use as a tabletop candelabra
Available in Traditional, Pillar,
and Teardrop styles
Part#/
Description
#FC-5TR-yy-xx
5-Light Tree
#FC-9TR-yy-xx
9-Light Tree
#FC-13TR-yy-xx
13-Light Tree
•
•
•
#FC-7FA-BR
FAN CANDELABRA
• 5, 7, and 15 light floor models
• Height adjustable
• 15 light candelabra not available in Pillar style
Part#
#FC-5FA-yy-xx
#FC-7FA-yy-xx
#FC-15FA-yy-xx
Description
5-Light Fan
7-Light Fan
15-Light Fan
DLR
$159.99 Ea
199.99 Ea
319.99 Ea
A great focal point for weddings and is convertible so it works as two different type of candelabras
Comes with accessories to convert from Unity (large flower set) to a Trinity (standard flower set) style candelabra
Overall size 22"W x 18"D with adjustable height from 53" to 78"H
DLR: $169.99 Ea
DLR
$169.99 Ea
229.99 Ea
299.99 Ea
Onyx Bronze
White
Nickel
Brass
Pictures may look slighty different than finished product
General Information
• Candelabra available in three styles (except as noted):
 Traditional - the classic taper holder flower set
 Teardrop - a 4" diameter glass cup suspended by a ring - use with floating candles (add color dye to the water for an added touch) or use disposable
votives for easy cleanup
 Pillar - a large drip pan with a 3/8" x 1" support post in the middle creates a solid platform for 3" diameter pillar candles; Pre-drilled Koch pillar candles are available or drill your own (call for more information)
• When ordering, substitute appropriate style code for "yy" in part number:
no style code (leave blank) = Traditional, TD = Teardrop, PI = Pillar
• Offer a second, or even all three styles by purchasing easy to change style conversion parts for your candelabra - avoids the cost of buying complete candelabra in every style - see page F7-8
• All candelabra, arches, and accessories available in Brass, Nickel (silver), Onyx Bronze, and White finishes
• Brass and Nickel finishes are electrostatically plated and acrylic-coated for long life; clean with dry cloth to remove fingerprints and debris – do not use cleaners or polishes which will remove the acrylic coating and cause
discoloration
• White and Onyx Bronze finishes are powder-coated; avoid abrasive cleaners which will damage the finish
• When ordering, substitute appropriate finish code for "xx" in part number: BR = Brass, NI = Nickel, ON = Onyx Bronze, WH = White
• 2-year limited warranty
To Order:
(
#FC-7AD-xx
CANDELABRA,
7-LIGHT
•
•
•
•
Traditional 7-light floor model
Adjustable arm angles
Height adjustable
Available in
Traditional style only
DLR: $189.99 Ea
Note: Orders for Koch Originals products on these pages
are themselves excepted from
the standard 5% RSS volume
discount, but do count towards
volume qualifications for other
items on the same order.
Call: (800) 233-0175
Fax: (717) 892-5981
Web: www.rssd.com
2014 Party Products
Non-Food Service
RSS
DISTRIBUTORS
B
17
#GC310
REPLACEMENT
CYLINDER
• For aisle candelabra
• Size: 3"D x 10"H
DLR: $49.99 6-Pack
279.99 48-Pack
#LFS-xx
LARGE FLOWER SET
Pillar Style
Teardrop Style
Traditional Style
#AC-1FR-yy-xx
1-LIGHT FREESTANDING AISLE CANDELABRA
•
•
•
•
•
Freestanding form allows for mobility and different designs
The elegant base lends support to the single candle at top
Overall dimensions: 13"W x 13"D; Height adjustable from 52" to 76"
Includes large flower set to hold glass chimney
Glass cylinders sold separately
DLR: $219.98 Pair
999.99 Ten-Pack
#LFS-BR
•
•
•
Convert candelabra for use as unity candelabra
Large flower set replaces small flower set in middle position and accommodates
3" pillar candle
Can be used to convert any candelabra to a pillar candelabra without needing to drill holes in candles
DLR: $9.90 Ea
CANDLE LIGHTERS
#CL-16U-WH
#CL-38V-WH
#AC-1QU-yy-xx
1-LIGHT AISLE CANDELABRA W/
QUICK CLAMP
•
•
•
•
•
•
Single-light aisle candelabra w/adjustable pew attachment clamp
Designed to take the least amount of space possible perfect for tight aisleways
Quick Clamp is padded to avoid scratching
Clamps onto pews from 1" to 2 3/4" thickness
Overall dimensions: 7"W x 6"D;
Height adjustable from 51" to 81"
Glass cylinders sold separately
DLR: $99.99 Ea
949.99 Ten-Pack
TD
•
•
•
•
•
Moving wick slide guides the wick up
The unity lighter is designed for the parents and does not have a snuffer
The universal lighter works great with all candelabra and has a small snuffer to fit into votive glass
The traditional lighter has a large snuffer designed for taper candles
Each comes with one wick
#CL-40T-ON
See Page C14 for
replacement wicks
Part#
#CL-16U-xx
#CL-38V-xx
#CL-40T-xx
Description
Length
Unity Candle Lighter
16"
Universal Candle Lighter 38"
Traditional Candle Lighter40"
DLR
$29.99 Ea
69.99 Ea
79.99 Ea
Note: Orders for Koch Originals products on these pages are themselves
excepted from the standard 5% RSS volume discount, but do count towards
volume qualifications for other items on the same order.
RD
B
18
Party Products
Non-Food Service
RSS
2014
DISTRIBUTORS
WEDDING ARCHES AND ACCESSORIES
WISH-xx
WISHING WELL
• Decorative card holder
• Clear Plexiglas cover with card
slot attaches with two bolts
• Dimensions: 14" diameter
29" height
Please refer to General Information
on Page B16 ordering instructions
#WA-50-NI Arch w/
#WAE-22-NI Extender
DLR: $149.99 Ea
#WA-60HE-BR Arch
WEDDING ARCHES
#WA-50-ON Arch
#WAE-22-ON Extender
• Commercial grade classic style wedding arches – designed for years of rental use
• Easily disassemble for storage and transport
• Extender adds 22" to the width of the standard arch
Part#
Description
Inside Width/ Overall
DLR
Length/Height Dimensions
#WA-50-xx
Standard Arch
50"W
74"W x 18"D x 92"H $429.99 Ea
#WA-60HE-xx Heart Arch
60"W
97"W x 18"D x 103"H 499.99 Ea
#WAE-22-xx
Standard Arch Extender
22"LN/A
49.99 Ea
#RS-FO-xx
FOLDING REGISTRY STAND/
PODIUM
•
•
•
#CHUPPAH-xx
CHUPPAH
•
•
•
•
•
Heavy-duty commercial grade chuppah or wedding canopy designed for a combination of elegance and sturdiness
Breaks down for easy storage and transport – can be assembled in less than 5 minutes
Bases can be secured to ground with spikes
Fabric and spikes not included
Dimensions: 8'W x 8'D x 8'H
DLR: $699.99 Ea
#KB-xx
KNEELING BENCH
Slip-on top lifts off and sides fold in
for easy storage and transport
Dimensions: 23"W x 16"D x 43"H
White wood book holder, 23" x 16"
•
•
•
DLR: $199.99 Ea
Padded knee and elbow rests w/
white vinyl covering
Purchase two to make configurations
Dimensions: 20"W x 18"D x 32"H
DLR: $199.99 Ea
Note: Orders for Koch Originals products on these pages are themselves excepted from the standard 5% RSS volume
discount, but do count towards volume qualifications for other items on the same order.
To Order:
(
Call: (800) 233-0175
Fax: (717) 892-5981
Web: www.rssd.com
2014 Party Products
Non-Food Service
RSS
DISTRIBUTORS
B
19
Please refer to General Information
on Page B16 ordering instructions
#FC-16WIL-ON
#FC-8WIL-ON
WILLOW STYLE CANDELABRA
#FC-24WIL-ON
#AC-1FR-WIL-ON
#AC-1QU-WIL-BR
• With the gracefulness and appeal of a willow tree, this unique style candelabra features hanging clear glass holders designed
for votive, tealight or floating style candles
• Clear glass candle holders are 2 1/2" high with a 2" interior diameter and a 3" lip
• Available in four standard finishes: Brass, Nickel, Onyx Bronze and White
• Not interchangable with other style (traditional, teardrop and pillar) Koch Originals candelabra
• Floor candelabra available in 8, 16 and 24-light models
Note: Orders
• Aisle candelabra (1-light) available in free-standing and quick-clamp models
nals products
Part#
#FC-24WIL-xx
#FC-16WIL-xx
#FC-8WIL-xx
#AC-1FR-WIL-xx
#AC-1QU-WIL-xx
Description
Willow style, 24-light free standing
Willow style, 1-light quick-clamp
#LUM-TC-1
ILLUMINATE GLOW CANDELABRA
Koch Originals
•
•
•
•
•
•
•
DLR
$449.99 Ea
349.99 Ea
249.99 Ea
219.98 Pair or $999.99 10-Pack
99.99 Ea or 949.99 10-Pack
for Koch Origion these pages
are themselves excepted from
the standard 5% RSS volume
discount, but do count towards
volume qualifications for other
items on the same order.
See Pages C12 - C13
for candle options
Acrylic 5-light tabletop candelabra is an affordable way to make an impression with a small candelabra
Offers unique beauty as light shining from the bottom reflects on the edges (lights and candles sold separately)
Use a variety of candle options (holds 1.5" tealight or LED candles) to accent the top
You can also light the bottom with different colors for amazing candelabra looks
Comes with a clear poly storage bag
Height: 17"
Note: Acrylic candelabras can scratch when not cleaned and stored properly - do not use harsh chemicals
DLR: $59.99 Ea
499.99 Ten-Pack
TD
RD
B
20
Party Products
Non-Food Service
RSS
2014
DISTRIBUTORS
COLUMNS, URNS, AND OTHER MOOD SETTING ACCESSORIES
ROTOMOLDED PRODUCTS
La Mirada, California.
• All products are manufactured from rotomolded polyethylene, one of the toughest plastics available.
• All stock products are white; many items can be special ordered in ivory, granite, sandstone, millstone
and blackstone finishes at a 10% surcharge
• All items are warranted, for a period of six months, to be free of defects in material and workmanship.
Warranty is expressly limited to selling price of items.
• Due to inherent limitations in the rotomolding process, all dimensions are nominal and may vary by small percentages from
piece to piece. This can be critical in terms of the standing height of large columns, particularly those used in colonnade
displays. When purchased in sets of two or more, RSS will ensure that the height of columns larger than 48" does not vary by
more than 1/4". When purchasing additional large columns to display with columns you already have, please specify the exact
height of your columns so that a close match can be provided
CLASSIC FLUTED
PEDESTALS
ARM-206
ARM-207
Square Base Column
• 30" and 40" pedestals are 9.5" in diameter and have fitted base
(either round or square) - buy caps separately for these products
• Pedestals may be fitted interchangeably with round, square, or ionic cap
• 96" "Giant Trojan" column is fitted with 16" square base and cap
ARM-406
Round Base Column
ARM-800
#ARM-202
#ARM-203
#ARM-204
#ARM-206
#ARM-207
#ARM-402
#ARM-403
#ARM-404
#ARM-406
#ARM-800
20" pedestal, square base 30" pedestal, square base 40" pedestal, square base 4" pedestal cap, square 5" pedestal cap, ionic 20" pedestal, round base 30" pedestal, round base 40" pedestal, round base 6" pedestal cap, round 96" Giant Trojan column $66.00 Ea
79.95 Ea
89.70 Ea
50.00 Ea
52.75 Ea
66.00 Ea
77.10 Ea
89.70 Ea
46.35 Ea
374.00 Ea
EMPIRE COLUMNS
ARM-802
• Similar to the Classic Fluted pedestals, these 7"
diameter columns have a fitted square base (10.5")
and a fitted "Empire" style cap (9.5" square)
• Use the Empire display cap (#ARM-802) to expand
top of column to a 12.9" square display base
#ARM-802*
#ARM-812
#ARM-818
#ARM-824
#ARM-832
#ARM-840
#ARM-848
#ARM-856
#ARM-872
#ARM-884
Empire display cap
12" Empire column
18" Empire column
24" Empire column
32" Empire column
40" Empire column
48" Empire column
56" Empire column
72" Empire column
84" Empire column
$34.85 Ea
70.75 Ea
71.20 Ea
86.60 Ea
88.60 Ea
94.00 Ea
99.90 Ea
107.15 Ea
143.30 Ea
165.10 Ea
*Note: Purchase #ARM-802 Display Cap to increase display space on top of Empire Columns
To Order:
(
Call: (800) 233-0175
Fax: (717) 892-5981
Web: www.rssd.com
2014 Party Products
Non-Food Service
RSS
DISTRIBUTORS
B
21
COLONNADE, ALPINE STYLE
Note: Colonnade shown is
comprised of:
• ARM-648 (4)
• ARM-600 (4), or
ARM-660 (4), or
ARM-884 (4), or
ARM-696 (4)
• ARM-618 (1)
RD
#ARM-648
Full -size quarter circle colonnade base/top $174.80 Ea
#ARM-672
72" straight colonnade section
171.65 Ea
top/base
#ARM-600
72" column with Scamozzi cap, 174.80 Ea
9 1/2" diameter (pictured)
#ARM-660
72" Tuscan column
174.80 Ea
#ARM-696
96" column with Scamozzi cap, 316.40 Ea
9 1/2" diameter
TD
#ARM-618
Colonnade arch, 72" x 18" H
184.50 Ea
#COLONNADE6
Colonnade group, 6' Scamozzi columns
1,583.00
$1,503.85
#COLONNADE6-TUS Colonnade group, 6' Tuscan columns
1,583.00
1,503.85
#COLONNADE7
Colonnade group, 7' Empire columns
1,544.10
1,466.90
#COLONNADE8
Colonnade group, 8' Scamozzi columns
2,149.40
2,041.93
Scamozzi
column
Empire
column
Tuscan
column
COLONNADES
• Construct using 48" quarter circle base/top pieces with 72" or
96" Scamozzi columns or with 84" Empire columns
• Form semi-circular or full circular colonnade with 8' diameter,
or use as shown in picture with arch
• Add 6' straight sections (two columns with top and base) to
colonnade structures as desired
• Urns in picture are not part of colonnade configuration
COLONNADE, DOME STYLE
Note: Colonnade shown is comprised of:
Full Oval
• ARM-649 (2)
• ARM-648 (4)
• ARM-660 (6), or
ARM-872 (6), or
ARM-884 (6)
• ARM-220 (6)
• ARM-661 (6), or
ARM-801 (6)
• ARM-620 (1)
• ARM-672 (1)
#ARM-649
#ARM-648
#ARM-660
#ARM-872
#ARM-884
#ARM-220
#ARM-661
#ARM-801
#ARM-620
#ARM-672
#ARM-647
#ARM-645
#CC-DOME6-TUS
#CC-DOME6-EMP
#CC-DOME7-EMP
#HC-DOME6-TUS
#HC-DOME6-EMP
#HC-DOME7-EMP
TD
Thin quarter circle base (left/right set of 2) Thick quarter circle, top of colonnade
72" Tuscan column 72" Empire column
84" Empire column
Multi-purpose light base
Column cap for #660 Tuscan columns
Column cap for #872 and #884 Empire columns
Soft curve arch
72" straight colonnade section top
Base end cap (half colonnade)
Top end cap (half colonnade)
Complete dome colonnade, 6' Tuscan
Complete dome colonnade 6' Empire
Complete dome colonnade, 7' Empire
Half dome colonnade 6' Tuscan
Half dome colonnade 6' Empire
Half dome colonnade 7' Empire
RD
Half Oval
• ARM-649 (1)
• ARM-648 (2)
• ARM-660 (4), or
ARM-872 (4), or
ARM-884 (4)
• ARM-220 (4)
• ARM-661 (4), or
ARM-801 (4)
• ARM-620 (1)
• ARM-647 (2)
• ARM-645 (2)
$179.20
174.80
174.80
143.30
165.10
79.00
43.95
43.95
187.70
171.65
56.15
TD
41.25
3,203.90 $3,043.70
3,014.80
2,864.06
3,145.50
2,988.23
2,102.60
1,997.47
1,976.50
1,877.68
2,063.65
1,960.47
RD
• Construct using full size quarter circle on top and thin
quarter circle on base of columns
• Choose desired column style and height (6' Tuscan,
6' Empire or 7' Empire)
• Must construct with appropriate column caps on
top and multi purpose light base on bottom of each
column
• Add 6' straight section to the back of colonnade and
a soft curve arch dome style piece to the front
• New multi-purpose light base is designed to take a
standard paving stone to add weight to colonnade
or columns
Party Products
Non-Food Service
B
22
RSS
2014
DISTRIBUTORS
GARDEN COLLECTION
• Specialty pieces designed to add a garden touch
• Recirculating fountain can be used indoors or outdoors
#ARM-216
#ARM-352
#ARM-748
#ARM-352
#ARM-216
#ARM-748
#ARM-349
#ARM-349
Garden bench, 52" long, 3-piece, Wt. Cap. 200 lbs.
Swan planter, 16" H Recirculating fountain, 48" H, 37" D
Flower Basket, 48", White
$228.20 Ea
83.90 Ea
456.15 Ea RD
141.40 Ea
Closeout
#310
#313
#319
CLASSIC URNS
#327
• Urns of various sizes and shapes coordinate well with pedestals and
balustrades
#ARM-310
#ARM-313
#ARM-319
#ARM-327
#ARM-416
#ARM-420
Grecian urn, 9.25" H, 7" T D
Inside B 2 1/2", 5" H, 6 1/2" D
Grecian urn, 13" H x 11.75" D
(Plant Holder: 6.25" B, 9.25"T, 8"H)
Large urn, 19" H x 21" D
(Plant Holder: 9" B, 15" T x 9.5 H)
Garden urn, 27" H
(Plant Holder: 6" B, 10"T, 13.5"H)
Classic urn, 14" H
(Plant Holder: 6" B, 9.75" T, 6.25" H)
Classic urn, 20" H x 15" D
(Plant Holder 5.5" B, 9.5" T x 7.75" H)
#416
#622
$46.50 Ea
57.10 Ea
#655
CONTEMPORARY URNS
118.20 Ea
101.00 Ea
58.50 Ea
#420
72.00 Ea
• Additional lightweight props from Meese
Orbitron can feature any of the premium finishes for
authentic stoneware look
• Available in two sizes and shapes as follows:
#ARM-622
#ARM-655
White urn, 22" H
White floor urn, 55" H
DORIC PEDESTALS;
COLONNADE PEDESTALS
• Similar to the Empire columns, the Doric
columns have a fitted round cap and base,
both in the "Doric" style
• Columns are approximately 9" diameter
• Colonnade pedestals, both Scammozzi
and Tuscan, 40", are fitted with a display cap
#640 w/#420
ARM-118
ARM-124
ARM-132
ARM-140
ARM-148
ARM-640
ARM-604
Doric column, 18"
Doric column, 24"
Doric column, 32"
Doric column, 40"
Doric column, 48"
Colonnade pedestal, 40", Scamozzi
Colonnade pedestal, 40", Tuscan
To Order:
#198108
STORAGE BAGS,
PLAIN
RSS
$67.60 Ea
73.00 Ea
81.65 Ea
89.55 Ea
112.80 Ea
105.80 Ea
95.50 Ea
(
• Bag your rotomolded columns
with the new #198108 bag
• 19.5" x 8.5" x 108"
• 100 bags per roll
DLR: $44.40
Call: (800) 233-0175
Fax: (717) 892-5981
Web: www.rssd.com
$101.80 Ea
184.50 Ea
2014 Party Products
Non-Food Service
RSS
DISTRIBUTORS
B
23
ARM-548
ARM-549
ARM-534
BALUSTRADE GROUP
• Construct 30" high balustrade of any desired length interspersing 4'
balustrade sections with balustrade pedestals and balustrade corners
• Classic urn with square base coordinates well with balustrade pedestal
#ARM-548
#ARM-549
#ARM-530
#ARM-534
#ARM-522
4' Balustrade section, 30" H. 4 balusters
Balustrade corner 30" H, 2 balusters
14" Balustrade pedestal, 30" H 16" Balustrade pedestal cap, 3" H Classic urn with square base, 22" H
$175.50 Ea
149.60 Ea
102.00 Ea RD
53.30 Ea
75.25 Ea
ARM-522
ARM-530
#ARM-220
MULTI-PURPOSE
LIGHT BASE
#ARM-200
LIGHT BASE
• 4 3/4" H x 15" Sq base fitted with small flood fixture
designed to light pedestals and other items from within
• Designed to take a standard paving stone to add weight
to colonnade or columns
• Attach light base to tee nuts molded into pedestals using
four bolts supplied with kit
• Base can be used with all Classic Fluted pedestals, all
Empire columns, the #600, #640 and #696 Scamozzi
columns, the #660 Tuscan column and the #522 Classic urn
• Change color of bulb for different effects
• Color: White
• Bulb not included
• Sold by each
DLR:
TD
• 3" high by 14" square base fitted with small flood fixture
designed to light pedestals and other items from within
• Attach light base to tee nuts molded into pedestals using
four bolts supplied with kit
• Base can be used with all Classic Fluted pedestals, all
Empire columns, the #600, #640 and #696
Scamozzi columns and the #522 Classic Urn
• Change color of bulb for different effects
• Bulb not included
• 6' cord
DLR:
$74.55
$79.00 Ea
RD
B
24
Party Products
Non-Food Service
RSS
2014
DISTRIBUTORS
Wedding Arches and Accessories
See page C12
for white and
ivory pillar
candles for
these candelabra
Artistic Metal Service
Scroll
21.5"
spread
Spiral
Unity
Stand
3-light
w/plant holder
Pyramid
40.5" Spread
Dice
Unity and Spiral shown complete with stands
7-light
w/plant
holder
5-Light Scroll Arm Pyramid
39.5" Spread
(Unity and 7-Light Scroll Arm Pyramids also available)
5 Lite Tree
23.5" Spread
7/8
Light
Tree
28.5"
spread
15 Lite Tree
43" Spread
9 Lite Tree
23.5" Spread
CANDELABRA,
BLACK wrought iron
•
•
•
•
•
•
•
•
•
All products have rustic black wrought iron look
All products formed from hot-rolled steel bar stock, 5/16" to 1/2" diameter
Products misted with black spray paint, then coated with clear polyurethane for rustic look
Trellises available in 8' and 10' gothic styles - use trellis candle hangers to position
pillar candles where desired on face of trellis
Ten different style floor candelabra available as pictured in first two rows above,
tops and bases are interchangable
Candelabra designed to hold 3" diameter pillar candles (unity candelabra holds two
tapers and a pillar candle)
Top of pole on unity, 15-light tree and dice candelabra is 4' off floor adjustable, up to 5.5' off floor
Top of pole on other candelabra is 5' off floor, adjustable up to 7' off floor
Scroll pole pyramid candelabra adjust in height to 3 positions only: 78", 85" and 91"
Part #
#AMS-FC50-10SL
#AMS-FC50-10SR
#AMS-FC40-5D
#AMS-FC50-5A
#AMS-FC50-3PS
#AMS-FC40-3UA
#AMS-FC50-7TR
#AMS-FC40-15TR
#AMS-FC50-9TR
#AMS-FC50-5TR
#AMS-FC50-7SPA
#AMS-FC50-5SPA
#AMS-FC40-3SA
#AMS-TC25-4AC
#AMS-GG50
#AMS-PS36
#AMS-FC40
#AMS-FC50
#AMS-FC50-5SPP
#AMS-FC50-7SPP
#AMS-FC50-9SPP
#AMS-TC30
Description
Candelabra, 10-light, spiral left, 6' pole
Candelabra, 10-light, spiral right, 6' pole
Candelabra, 5-light, dice, 4' pole
Candelabra, 5-light, pyramid, 5' pole
Candelabra, 3-light w/plant holder, scroll, 5' pole
Candelabra, 3-light, unity, 4' pole
Candelabra, 7/8 light tree, 5' pole
Candelabra, 15-light tree, 4' pole
Candelabra, 7-light scroll arm pyramid, 5' pole
Candelabra, 5-light scroll arm pyramid, 5' pole
Candelabra, scroll arm unity pyramid, 4' pole
Candelabra, four-arm centerpiece, 30" pole
Garden Globe, 5'H
Plant stand 36" H, w/10" holder
Candelabra base and pole only 4' H
Candelabra base and pole only 5' H
Candelabra 5-light scroll pole pyramid, 5' pole
Tabletop centerpiece, 8" Dia. Top, 30 H, 3 leg
To Order:
DLR
$292.50
292.50
292.50
202.50
240.00
180.00
277.50
382.50
322.50
292.50
255.00
210.00
187.50
63.00
103.50
45.00
103.50
103.50
240.00
277.50
315.00
79.50
(
Plant
Four-Arm Centerpiece Stand
28" Spread
30.5" high
Garden
Globe
14"
spread
60" high
Tabletop
Centerpiece
Scroll
Pole Pyramid
9 Light
Scroll
Pole Pyramid
5 Light
Scroll
Pole Pyramid
7 Light
Call: (800) 233-0175
Fax: (717) 892-5981
Web: www.rssd.com
2014 Party Products
Non-Food Service
RSS
DISTRIBUTORS
kdjfld
B
25
TRELLISES AND ARCHES, BLACK WROUGHT IRON
Artistic Metal Service
117"W x 16"D x 113"H
(Overall dimensions)
111"W x 16"D x 100"H
(Inside Dimensions)
90" W x 96" H
(Overall dimensions)
54" W x 81" H
(Inside Dimensions)
Crown Point Arch
Three Ring Arch
Gothic Trellis
Part#
#AMS-WA
#AMS-GT8
#AMS-GT10
#AMS-CH1
#AMS-CPA
#AMS-CPG
Description
Three-ring arch, 90" H
Gothic trellis w/stand, 8' H, 42"W Gothic trellis w/stand, 10' H, 48"W
Trellis candle hangers
Crown point arch 111" W x 16" D x 100" H
Crown point gazebo constructed from 3 arches
plus additional perimeter scroll work
DLR
$450.00
187.50
277.50 RD
13.50
472.50
2,835.00
TABLETOP WATER FOUNTAINS
CENTERPIECE WATER FOUNTAINS
Buffet Enhancements
1BMF26
1BMF30
#1BMF26
#1BMF30
•
•
•
•
•
•
•
•
Capacity: 3 gallons
Dimensions: 26" D x 9" H
Water Height: 18"
Weight: 18 lbs
DLR: $1,228.00 Ea
1,166.60 TD
TD
• Use these Marquis FountainsTM by Buffet Enhancements as attention
getting centerpieces on a buffet line, in event gathering places, etc.
• Fountains feature one-piece fiber-reinforced bowls fitted with
recirculating pump - water supply not needed
• Hand brazed copper rings and precision brass fountain jets
• Ground-fault electrical protection
• Underwater lighting adds color to water jets
• Available in black diamond and alabaster finishes
Capacity: 4 gallons
Dimensions: 30" D x 11" H
Water Height: 28"
Weight: 26 lbs
Note: For decorative use only - not
intended for foodservice
DLR: $1,228.00 Ea
1,166.60 TD
RD
B
26
Party Products
Non-Food Service
RSS
2014
DISTRIBUTORS
wedding ARbors
Maintenance-Free Vinyl
Products
• Beautifully crafted collection
of garden products
• Durable and impact
resistant
• Pure white; never needs
painting
• Will not dent, rust or
become "hot to the touch"
• Will not crack, peel, or yellow
• Lifetime manufacturer
warranty against defects
• All items can be shipped via
UPS
Note: All items available in
Ivory at 15% upcharge
Lower
Price!
Lower
Price!
#SPP-PLYMOUTH
PLYMOUTH ARbor
• Extra-heavy construction with elegant arch
connecting wicker side sections
• Dissembles quickly without tools
into two side sections, two arch
pieces and eight arch spokes
• 50" wide x 32" deep
• Arch height: 84"
#SPP-THA48
TWO HOOP ARbor
• Ideal economy wedding arch
• 4' wide X 26" deep
• Arch height: 87"
DLR: $137.25
DLR: $486.50 RD
classic arbors
Jefferson
Kingston
Heritage
CLASSIC ARBORS
• Above arbors are 50" or 66" wide, 84" high
(Jefferson is 80") and 32" deep
• All feature 4" x 4" posts
• All require removal of approximately twelve
screws for disassembly and storage
#SPP-HERITAGE #SPP-KINGSTON
#SPP-JEFFERSON
Heritage Style
Kingston Style
Jefferson Style
#SPP-ASK
SEAT PACKAGE KIT
• Optional seats fit any of the
three above arbors
• Kit includes two seats, one for
each side of arbor
RD
$466.20
537.00
425.00
DLR: $155.50
Note: Due to the multiplicity of parts and the screw-together nature of the
assembly, RSS cannot accept returns on any of these three Classic Arbors.
To Order:
(
Call: (800) 233-0175
Fax: (717) 892-5981
Web: www.rssd.com
2014 Party Products
Non-Food Service
RSS
DISTRIBUTORS
B
27
TABLETOP CENTERPIECES
#90443
CANDELABRA,
NICKEL PLATED W/SHADES
CANDELABRA, NICKEL PLATED
RSS
RSS
• Tall table model five-light candelabra
with non-tarnish nickel-plated finish
• Rounded center post
• Optional floral bowl: 9" D x 3 1/2" H,
sits in center candle holder
• Height: 30"
#90445
#9044
Five-light candelabra, 30" H
Floral bowl
• Tall, table model candelabra with non-tarnish nickel-plated
finish
• Four-light with integral floral bowl
• Flared glass shades are 9.5" tall and 4.5" in diameter
• Shades are held in place by spring-loaded clips on each
candle holder
• Height: 41" (top of floral bowl)
43" (top of glass shades)
90.00 Ea
12.00 Ea
DLR:
$174.00 Ea
MINT JULEP CUPS, NICKEL
PLATED
CANDELABRA, NICKEL PLATED
RSS
RSS
• Perfect for small centerpiece floral arrangements
• Non-tarnish nickelplate finish on stainless steel safe to drink from
• Two different sizes available as follows
• Tall, table model candelabra with non-tarnish
nickel-plated finish
• Five-light with optional floral bowl
• Floral bowl: 9" D x 3 1/2" H, sits in center
candle holder
#90441A Five-light candelabra, 38" H $150.00 Ea
#90442A Five-light candelabra, 31" H
99.00 Ea
#9044
Floral bowl
12.00 Ea
#90471
#90472
Large Cup
12 Oz. 4 1/2" H x 3 5/8" D
Medium Cup 6 Oz. 3 1/2" H x 2 7/8" D
$7.50 Ea
6.00 Ea
CENTERPIECE GLASSWARE
FLOATING CANDLE VASES
See Page
C12 for
Floating
Candles
RSS
• Use cylindrical glass vases of different heights to create
unique floating candle centerpieces
• Hand blown
• Glass vases are 4" diameter by 8", 10" and 12" in height
• All vases sold in case quantities
Part No.
Description
#CY-408 Vase, 4"D x 8"H
#CY-410 Vase, 4"D x 10"H
#CY-412 Vase, 4"D x 12"H
Case DLR Info Only
Qty
(Cs)
(Ea)
12
$32.40 $2.70
12
40.50 3.38
12
48.60 4.05
#3PGLCH
PILLAR CANDLE HOLDERS,
MATCHED SET
#Z57-74
DOMED VOTIVE HOLDER
CENTERPIECE GLASS
RSS
TD
Note: Hand blown glass is inherently flawed.
Small bubbles and faults are acceptable and even
desirable as an indication of the quality.
RSS
• Glass pillar candle holders in style of long-stemmed
glass
• Candle holding cylinders are 3.75" in diameter x 4"
high - (perfect for 3" x 3" pillar candles)
• Sold as a matching set of three complementary
holders with overall heights of 12", 16" and 20" for
use as a centerpiece grouping
• Sold in cases of 4 sets
• Dual purpose clear glass centerpiece
• Fill base of dome with decorative items
• Removable glass cup at top of dome
accommodates votive candles or tea lights
• Dimensions: 6.5" diameter x 7" height
• Sold four per case
DLR:
DLR:$53.20 Cs ($13.30 Ea)
$90.00 Cs (22.50 Set)
RD
Closeout
B
28
Party Products
Non-Food Service
RSS
2014
DISTRIBUTORS
TABLETOP CENTERPIECES
CENTERPIECE ACRYLIC MIRRORS
Buffet Enhancements
• Lightweight portable and cost efficient centerpiece mirrors
• High quality acrylic construction accommodates removal of marks and scratches with
acrylic polish (or car polish)
• Specially designed carrying case with partitions that separate and protect individual
mirrors available as separate item
• Carry case dimensions: 17"L x 12" D x 9" H - holds 25 mirrors
• Mirror diameter: 14"
• Mirrors available as follows
TD
DLR
#1BAMV14
Acrylic mirror, 14"
Each
$28.30
$26.89
#1BAMV25
Acrylic mirrors, 14"
Set of 25
581.75
552.66
#1BAMCC25SET Acrylic mirrors, 14" Set of 25 w/case
646.75
614.41
#1BAMV50
Set of 50
1,137.50 1,080.63
#1BAMV100
Set of 100
2,242.50 2,130.38
#1BAMCC25
Carry Case, 25 mirrors
Each
98.80
93.86
1BAMCC25SET
Lower
Prices!
1BAMV100
• Use these oversized pieces to provide striking
centerpiece presentations
#1789306
FLARE
#9570101
SUPER MARTINI
• 59 Ounces
• 5" Height
• 10" Max. Dia
•
•
•
•
DLR: $16.40 Ea
DLR: $126.00 Cs
48 Ounces
10 1/8" Height
9 1/4" Max. Dia
6/Case
SPARKLE CRYSTAL
CANDELABRA COLLECTION
RSS
• A collection of candelabra designed to produce a unique shimmering
effect
• Candelabra shades are constructed from small clear glass beads wired
together in a regular pattern
• Glass beads act as a prism to scatter light in all directions while hiding
candles themselves
• Nickel-plated construction of base provides highly polished, no-tarnish
finish
• Ball candle stands designed for 3" pillar candles, other pieces designed
for tea lights
• Choose from following pieces
#72890
#72884
#72885
#72886
#72876
#72890
#72892
#72897
#72898
#72899
#72897-72898-72899
#72892
#72876
#72884 #72886 #72885
To Order:
(
Tea Light Candlestick, 2 1/2" D x 9 1/2" H
Tea Light Candlestick, 2 1/2" D x 10 1/2" H
Tea Light Candlestick, 2 1/2" D x 12" H
Tea Light Holder, 2 1/2" D x 2 1/2" H
Cake Stand, 14" Round
Globe Tea Light Holder, 3"
Ball Candle Stand, 6.5" D Ball x 21" H
20.00 Ea
21.00 Ea
22.00 Ea
10.00 Ea
90.00 Ea
10.00 Ea
54.00 Ea
57.00 Ea
60.00 Ea
Warning: Glass bead shades are somewhat fragile and will not
withstand rough handling - set rental pricing accordingly.
Call: (800) 233-0175
Fax: (717) 892-5981
Web: www.rssd.com
2014 Party Products
Non-Food Service
RSS
DISTRIBUTORS
B
29
TALL VASES,
FLARED AND SQUARE
RSS
• Tall vases in elegant shapes and forms
• Heavy glass products with excellent clarity
• All products must be purchased in case quantities (due to difficulty of shipping)
#Z17-2671A
#Z17-2671
#Z17-1350C
#S6624
Z17-2671
S6624
DLR
(Cs)
Case
Quantity
Flared-Top Vase, 7.25" x 31.5" H
Flared-Top Vase, 6.75" x 27.5" H
Square Vase, 6" x 27.75" H
Square Vase, 6" x 24"H
4
4
4
6
Info Only
(Ea)
$193.20
148.40
179.20
162.00
$48.30 CLOSEOUT
37.10 CLOSEOUT
44.80 CLOSEOUT
27.00
Z17-1350C
TALL VASES,
TRUMPET STYLE
RSS
• Tall trumpet shaped glass vases suitable for centerpiece creations
• Heavy glass products with excellent clarity
• All products must be purchased in case quantities (due to difficutly of shipping)
Case
DLR
Info Only
Quantity
(Cs)
(Ea)
V-727
Z30
#V-727
#Z30
Trumpet-Shaped Vase, 7"D x 27"H
Trumpet-Shaped Vase, 6.2" TD x 30" H
$78.20
90.00
4
6
$19.55 CLOSEOUT
15.00
MULTI-PURPOSE CENTERPIECE GLASS
RSS
REC-4126
4" x 12" x 6" H
• Use for floral arrangements, floating candle holders, square pillar candle holders, etc
• Imported from Far East sources
• All products must be purchased in case quantities (due to difficulty of shipping)
SQ-666
6"
SQ-444
4"
TD
CY-804
8" x 4" H
CY-806
8" x 6" H
#REC-4126
#SQ-666
#SQ-444
#CY-806
#CY-804
Rectangular Vase, 4" x 12" x 6"H
Square Vase/Pillar Holder, 6" x 6" x 6"H
Square Vase/Pillar Holder, 4" x 4" x 4"H
Round Vase/Floater Holder, 8"D x 6"H
Round Vase/Floater Holder, 8"D x 4"H
Case
Quantity
DLR
(Cs)
Info Only
(Ea)
6
6
12
6
12
$79.20
28.80
23.40
33.30
55.80
$13.20
4.80
1.95
5.55
4.65
Note: Products on this page are hand blown glass and as a
result, inherently flawed. Small bubbles and faults are acceptable and even desirable as an indication of the quality.
RD
B
30
Party Products
Non-Food Service
RSS
2014
DISTRIBUTORS
CENTERPIECE LIGHTING
E-LUMINATOR LIGHT BASES
Acolyte Technologies
#AT-19521
E-MINI™ 9
AT-19510
• Illuminating bases will
light any transparent or
translucent design
placed on top of them
• Round silver plastic
base with super bright
LED lights protruding
under a plastic cover
• All include an on/off switch
ORIGINAL E-LUMINATOR™
•
•
•
•
Part#
#AT-19510
#AT-19512
Description
E-Luminator™ 13
E-Luminator™ 31
E-MAXI™ 32
•
•
•
•
•
•
AT-19512
Diameter: 8"
Embedded LED's: 13 (AT-19510) / 31 (AT-19512)
Power Source: "AA" Batteries (3)
Battery Life: 8 Hours
DLR
$17.30 Each
25.60 Each
Description
E-Maxi™ 32 White
E-Maxi™ 32 RGB
DLR
$30.45 Each
46.00 Each
AT-19522
DLR (Case)
$658.00 Case of 24
497.35 Case of 12
•
•
•
•
•
Centerpiece spotlight on a pivot for easy directionality
Light contains 20 super bright RGB LED bulbs
6 color functions
On/off switch
Power source: AA alkaline batteries (3)
or optional 5-volt AC adapter
• Remote control capable
Remote
• Battery life: 8 hours
Capable
• Dimensions: 3" diameter x 8" high
Part#
#AT-21512
#AT-05016
#AT-05017
DLR
$88.90 Pack of 3
6.00 Each
5.25 Each
Description
20-Spot RGB
RGB Remote Control
5-Volt AC Adapter
DLR (Case)
$639.90 Case of 24
129.60 Case of 24
113.40 Case of 24
AT-19525
E-WALL WASH™
ACOLYTE ACCESSORIES
• Battery powered LED wash light on pivot
contains 60 white LEDs arranged in a rectangular grid
• Wirelessly illuminate where inconvenient to run wires
• Power Source: "AA" Batteries (8)
Closeout
• Battery Life: 8 Hours
• Dimension: 6 7/8" W x 3 1/4" H x 3 1/2" D
• Standard unit is controlled by manual on/off switch
• Remote capable unit can be controlled by optional remote control and can also
be powered by optional 12-volt AC adapter for long term displays and events
• Purchase individually or by the case as follows:
Part#
Description
#AT-19523 E-Wall Wash Remote Capable
#AT-05015 Standard Remote Control
#AT-05018 12-volt AC Adapter
DLR:$34.20 Pack of 3
738.70 Case of 72
Remote
Capable
20-SPOT™ RGB
LED CENTERPIECE SPOTLYTE
Remote
Capable
Diameter: 8"
Embedded LED's: 32
RGB unit adds 6 color functions
Power source: AA Batteries (3) or optional 5-volt AC adapter
Battery Life: 8 Hours
Remote control capable
Part#
#AT-19522
#AT-19525
DLR (Case)
$373.68 Case of 24
552.95 Case of 24
• Improved version of the original E-Mini-Luminator
• Diameter: 4"
• 9 Protruding LEDs under clear plastic cover provide
more illumination
• Remote control capable
• Power Source: AA Batteries (3) or optional
5-volt AC adapter
• Battery Life: 8 Hours
DLR
Each
48.00
5.25
6.75
Case
Qty
12
24
24
To Order:
DLR
Case
518.40
113.40
145.80
• Standard remote control turns any Acolyte remote capable unit on or off
• Remote control range: 4 - 6 feet
• RGB remote control adds the ability to change colors on any RGB
capable unit
• 5-volt AC adapter can be used with any AC equipped unit except
the E-WallWash™
• E-WallWash™ requires the 12-volt AC adapter
Part#
#AT-05015
#AT-05016
#AT-05017
#AT-05018
#AT-05013
Description
DLR
DLR (Case)
Standard Remote Control
$5.25 Each
$113.40 Case of 24
RGB Remote Control
6.00 Each
129.60 Case of 24
5-Volt AC Adapter
5.25 Each
113.40 Case of 24
12-Volt AC Adapter
6.75 Each
145.80 Case of 24
CR2025 battery for remotes 2.70 Pack of 4 87.50 Case of 144
AT-05015
(
AT-05016
Call: (800) 233-0175
Fax: (717) 892-5981
Web: www.rssd.com
AT-05017/AT-05018
2014 Party Products
Non-Food Service
RSS
DISTRIBUTORS
B
31
TENT LIGHTING
Candelabra (E12) Base Stringers and BulbsDLR
Stringer
C9 Bulb
3" x 1"
C9 LED Bulb
2 1/2" Long
C7 Bulb
2" x 7/8"
C7 LED Bulb
1 1/2" Long
Candelabra (C7) Base and Intermediate
(C9) Base Light Stringers and bulbs
RSS
•
•
•
•
•
•
•
•
•
•
For indoor and outdoor use
Heavy-duty SPT-1 sockets spaced 12" apart
White AWG-18 cord
Available in 25' (w/plug and end-to-end connectors),
100' (w/plug only) and 1000' (bulk-no plugs or
connectors) lengths
UL listed, commercial-grade bulbs, w/brass base
Average standard bulb life: 3,000 hours
LED bulb shells made of weather resistant,
break resistant durable plastic
LED bulbs produce little heat and consume only
about 10% of the power of standard incandescent
bulbs
Maximum runs: 840 W (7A)
C7 LED bulbs are .37 watt; C9 LED bulbs
are .49 watt
Stringers
#XSC25W12
#XSC100W12
#XSCB1000W12
Candelabra Base, 25', White Cord, No Bulbs
Candelabra Base, 100', White Cord No Bulbs
Candelabra Base, 1000' Bulk White Cord, No Bulbs, No Plugs
$10.35 Ea
34.60 Ea
263.20 Ea
Case
Qty
DLR
(Case)
50
10
1
$465.00
312.00
263.20
C7 Bulbs
RD
#5C7CL
#7C7CL
#7C7WH
Incandescent, 5 Watt Clear, 25 per Box
Incandescent, 7 Watt White, 25 per Box
4.75 Bx
4.75 Bx
4.75 Bx
40
40
40
170.00
170.00
170.00
#LDC7WW
#LDC7WH
LED, .37 Watt, Warm White, 25 per Box
LED, .37 Watt, Pure White, 25 per Box
34.35 Bx
34.70 Bx
20
20
618.00
624.60
12.95 Bx
14.30 Bx
20
20
233.00
257.40
$10.90 Ea
36.85 Ea
292.50 Ea
50
10
1
$490.00
332.00
292.50
Globe Bulbs (G50)
#G507E12CL
#G507E12WH
Intermediate (E17) Base Stringers and Bulbs
Stringers
#XSI25W12
#XSI100W12
#XSIB1000W12
Intermediate Base, 25' White Cord, No Bulbs
Intermediate Base, 100' White Cord, No Bulbs
Intermediate Base, 1000' Bulk White Cord,
No Bulbs, No Plugs
C9 Bulbs
RD
#7C9CL
#7C9WH
#LDC9WW
#LDC9WH
LED, Warm White, 25 per Box
LED, Pure White, 25 per Box
5.75 Bx
5.75 Bx
40
40
207.20
207.20
39.45 Bx
39.80 Bx
20
20
710.00
716.40
Globe Bulbs (G30, G50)
#G505E17CLRC
2" Diameter
#G507E17CL
2" Diameter
G507E12WH
2" Diameter
#G505E17CLRC
#G507E17CL
#G507E17WH
Incandescent, G50, 5 Watt Clear,
w/5 Rice Lights, 25 per Box
Incandescent, G50, 7 Watt Clear, 25 per Box
Incandescent, G50 7 Watt White, 25 per Box
35.75 Bx
10
321.95
14.60 Bx
18.00 Bx
20
20
263.00
324.00
#LDG30SSWW
#LDG30SWH
#LDG40SWW
#LDG40PW
LED, G30, Sun Warm White, 25 per Box
LED, G30, Cool White, 25 per Box
LED, G40, Sun Warm White, 25 per Box
LED, G40, Pure White, 25 per Box
51.00 Bx
51.00 Bx
57.10 Bx
57.10 Bx
20
20
20
20
918.00
918.00
1,028.00
1,028.00
Candelabra and Intermediate Base Accessories
G30 Bulb
1-1/8" Diameter
Plastic Shell
TD
G40 LED Bulb
1-1/2" Diameter
Plastic Shell
FSIPLG-WH
MSIPLG-WH
Female Slip-in Plug, White, 12 per Box
Male Slip-in Plug, White, 12 per Box
13.90 BxN/AN/A
12.90 BxN/AN/A
#FSIPLG-WH
RD
B
32
Party Products
Non-Food Service
RSS
2014
DISTRIBUTORS
N
TENT LIGHTING
Medium Base Stringer
Medium Base (E27) Light
Stringers and bulbs
Medium (E27) Base Stringers and Bulbs
RSS
• Designed for year-round outdoor use
• Commercial grade, heavy-duty SPT-2
sockets spaced 24" apart
• AWG-16 cord
• PVC - encapsulated sockets with brass
contacts resistant to UV exposure
• Sockets designed to ensure snug,
weather resistant seal
• Plug w/6' lead included on 54' and
106' stringers
• LED plastic bulbs have a faceted cover
that is both weather-resistant and breakresistant
• LED classic bulbs have clear, smooth
glass cover
• Incandescent bulbs rated at 2,500 hours;
LED bulbs at 50,000 hours
• LED lights are safe - they produce no
heat and are cool to the touch
• Commercial Grade UL Listed bulbs for
indoor and outdoor use
• LED bulbs are available as "Warm White"
(equivalent to clear incandescent) or
"Cool White" (bluish tint)/"Pure White" (bright white) (equivalent to white incan-
descent)
• Available in 54', 100' and 330' lengths
• Short stringers (54' and 106') are fitted
with plug and 6' lead to first socket
• To adapt stringers for end-to-end
connection, replace last socket
on string with female rubber
plug (#PLGF-WH)
• Maximum run: 960 Watts
#PLGM-WH
#G5015E27CL
2" D
#11S14CL
3 1/2"L; 1 3/4" D
Stringers
Your choice
Black or White
RD
DLR
#LSM2448BK
#LSM2448WH
#LSM24102BK
#LSM24102WH
#LSM24330BK
#LSM24330WH
Party Bulbs
Medium Base, 54' Black Cord, 24 Sockets, No Bulbs
Medium Base, 54' White Cord, 24 Sockets, No Bulbs
Medium Base, 106' Black Cord, 50 Sockets, No Bulbs
Medium Base, 106' White Cord, 50 Sockets, No Bulbs
Medium Base, 330' Black Cord, 165 Sockets,
No Bulbs, No Plugs
Medium Base, 330' White Cord, 165 Sockets,
No Bulbs, No Plugs
(S14)
Case
Qty
DLR
(Case)
$102.40 Ea
102.40 Ea
188.80 Ea
188.80 Ea
609.00 Ea
8
8
4
4
1
$737.60
737.60
679.60
679.60
609.00
609.00 Ea
1
609.00
#11S14CL
Incandescent, 11 Watt S14 Clear Bulb, 20 per Box
$12.15 Bx
60
$657.00
#LDS14SWW
#LDS14PW
#LDG50SWW
#LDG50PW
#LEDGS14WW
#LEDGS14WH
LED, .55 Watt S14 Plastic Bulb, Warm White, 25/Box
LED, .55 Watt S14 Plastic Bulb, Pure White, 25/Box
LED, .55 Watt G50 Plastic Bulb, Warm White, 25/Box
LED, .55 Watt G50 Plastic Bulb, Pure White, 25/Box
LED, .7 Watt S14 Sign Bulb, Warm White, 25 per Box
LED, .7 Watt S14 Sign Bulb, Cool White, 25 per Box
107.60 Bx
107.60 Bx
107.60 Bx
107.60 Bx
182.00 Bx
182.00 Bx
10
10
10
10
6
6
968.40
968.40
968.40
968.40
982.80
982.80
26.80 Bx
20
482.40
182.00 Bx
182.00 Bx
6
6
982.80
982.80
Globe Bulbs (G50)
#G5015E27CL
Incandescent, 15 Watt G50 Clear Bulb, 25 per Box
#LEDGG50WW LED, .7 Watt G50 Bulb, Warm White, 25 per Box
#LEDGG50WH LED, .7 Watt G50 Bulb, Cool White, 25 per Box
Medium Base Accessories
#PLGF-BK
#PLGF-WH
#PLGM-BK
#PLGM-WH
Female Rubber Plug, 15 AMP Black, 10 per Box
Female Rubber Plug, 15 AMP White, 10 per Box
Male Rubber Plug, 15 AMP Black, 10 per Box
Male Rubber Plug, 15 AMP, White, 10 per Box
#LDS14SWW
LED Plastic
S14 Bulbs
3 1/2"L; 1 3/4"W
To Order:
#LDG50PW
LED Plastic
G50 Bulb
2" D
(
$47.60 Bx
47.60 Bx
39.95 Bx
39.95 Bx
#LEDGS14WW
LED Classic S14
Bulb
3 1/2"L; 1 3/4"D
Call: (800) 233-0175
Fax: (717) 892-5981
Web: www.rssd.com
#LEDGG50WW
LED Classic
G50 Bulb
2" Diameter
2014 Party Products
Non-Food Service
RSS
DISTRIBUTORS
B
33
TENT LIGHTING
Medium (E26) Base Stringers and Nostalgic Bulbs
Stringers
Size
DLR
Case DLR
Qty (Case)
#810001
Medium Base, 48', Black Cord, 15 Suspended Sockets
$79.10 Ea 4 $287.70
Medium (E26) Base Nostalgic Collection Bulbs
NOSTALGIC COLLECTION
MEDIUM (E26) BASE
Stringer and bulbs
#132520
#134014
#134015
#342040
#134018
#132509
A19 Loop, 25 Watt Clear, 6 per Box
T14 Spiral, 40 Watt Clear Amber, 10 per Box
T14 Thread, 40 Watt Clear Amber, 10 per Box
G30 Thread, 40 Watt Clear, 6 per Box
ST18 1890 Edison, 40 Watt, Clear, 6 per Box
T9 Tubular Hairpin, 20 Watt, Clear, 12 per Box
RD
4 1/2"L x 2 1/2"D
4 1/4"L x 1 3/4"D
4 1/4"L x 1 3/4"D
5 1/8"L x 4"D
5"L x 2 1/4"D
7 1/2"L x 1 1/4"D
49.00 Bx
57.75 Bx
57.75 Bx
66.85 Bx
49.00 Bx
64.35 Bx
96
50
50
48
96
96
712.80
262.50
262.50
486.00
712.80
468.00
RSS
Meticulously handcrafted to preserve the look of early
20th-century lighting, the Nostalgic Collection is the
perfect complement to any vintage or contemporary
décor. Recognized for their antique finish, defined
steeple and intricate filament design, these bulbs are
ideal for any transparent light fixture, both indoor
and outdoor.
• For indoor and outdoor use
• Black UL approved AWG-16 cord stringer, 48' length
• 15 heavy-duty suspended sockets spaced 36" apart
• Molded plug and end-to-end connector
• Replica incandescent antique bulbs w/brass base
• T14 Bulb shells have a slight amber tint; the others are clear
• Average standard bulb life: 3,000 hours
• Bright filaments give off a warm, amber glow, perfect for any antique décor
• Maximum runs: 1500 W (12.5A)
#810001 Stringer
Suspended Socket
#132520
A19 Loop
#134014
T14 Spiral
#134015
T14 Thread
#342040
G30 Thread
#134018
ST18 1890 Edison
#132509
T9 Tubular Hairpin
Note: E26 Bases are shorter than E27 Bases (by one thread), and do not extend as deeply into the socket. While E26 bulbs will usually work
in an E27 socket, you will need to screw them in extremely tight. Therefore, it is recommended that you use E26 bulbs in E26 sockets.
White Cords, White or Clear Prismatic Globes
OUTDOOR GLOBE LIGHTS
Polymer Products
STRLGT-6WHP-PT
STRLGT-6CPA-PT
STRLGT-10WHP-PT
STRLGT-10CPA-PT
• Great for all kinds of outdoor and tent functions
• Six globe lights mounted on 10' 9" cord (stretchable to 30'), or ten globe
lights mounted on 18' cord (stretchable to 50')
• Sockets are 27" apart (80" with cord fully stretched)
• Cords are white with white sockets or black with black sockets
• All white globes are 6" polycarbonate (nearly unbreakable)
• Black shades can be used on any of the light strings - order separately
• Use up to 60W bulbs (not included)
• Power cord extends 20' from first globe
• All strings include pigtail for end-to-end plug compatibility
• Easy to repair
• Globes available in white, clear prismatic or bronze prismatic
• Clear and bronze globes are 6" prismatic acrylic
• UL listed for wet locations
See Page B35 for replacement globes
TD
Six-Light String, White $84.20 String
Globe on White Cord
Six-Light String, Clear 84.20 String
Prismatic Globe on White Cord
Ten-Light String, White Globe 106.70 String
on White Cord
Ten-Light String, Clear Prismatic 106.70 String
Globe on White Cord
Black Cords, Bronze Prismatic Globes
STRLGT-6BLK-BR-PT
STRLGT-10BLK-BR-PT
STRLGT-SHADE
RD
Six-Light String Bronze $84.20 String
Globe on Black Cord
Ten-Light String Bronze 106.70 String
Globe on Black Cord
Optional Black Shade
3.95 Ea
B
34
Party Products
Non-Food Service
2014
tent lighting
t
l
ia
tr y
s
du lit
In ua
Q
LIGHT SETS, CLEAR ON WHITE OR BROWN
RSS
• 50 light strings on 22 1/2' white or brown braided 3-wire cord
• 200 milliamp superbright clear bulbs - 2500 hour life
• 6" bulb spacing
• End-to-end connectors w/4" spacing to first bulb
• "Stack-on" plug on back of male connector
• String stays lit when bulb goes out
• Replaceable fuse on each string
• Connect up to 80 strings on one 20 amp circuit
• UL listed per new, more stringent code for indoor and outdoor use
• Each string shipped with two extra bulbs and one extra fuse
• Sold per string and per case
DLR Case DLR
(String) Qty (Case)
#CW50ID Minilights, 50 clear on white $9.55 36 $326.52
#CG50OD Minilights, 50 clear on brown 9.55 36 326.52
RSS
DISTRIBUTORS
tent lighting
ULTRA ORBS
Fortune Products
LED
• A new and exciting addition to your
outdoor party decor
• Sizes from 12" to 24"
• Made from shiny hard white acrylic material
• Features slow color change options in red,
blue, green and white
• Set it to stop on a single color or a
combination of colors for special hues
• Hang it, float it or use as a stationary prop
• All metal outer battery compartment and cover has a hole to attach a line
for hanging or for an anchor in floating applications
• Incredible effect in brilliant colors for swimming pools, ponds, lakes and
other water applications
• Awesome hanging from trees, ceilings or other structures
• Uses four "D" batteries (not included) for long battery life
• Plug jack inside the battery compartment for adapting power for more
permanent applications (not in water)
• Now available with remote control
#R-ORB12
#R-ORB16
#R-ORB20
#R-ORB24
12" Ultra Orb
16" Ultra Orb
20" Ultra Orb
24" Ultra Orb
$87.60
119.85
159.70
269.90
RD
With Remote
#R-ORB12-RC
#R-ORB16-RC
#R-ORB20-RC
#R-ORB24-RC
12" Ultra Orb
16" Ultra Orb
20" Ultra Orb
24" Ultra Orb
#ADAP-LLAS1000
AC Adapter
112.60
142.30
178.50
281.65
8.70
#DXML-70-WWW
LED MINILIGHT STRING
National Speciality Lighting
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Uses 90% less power than ordinary lights
Virtually no heat output
110 volt input: 5 watt energy usage
UL listed for indoor and outdoor use
Strings can be connected up to 40 sets
100,000 hour lamp life
Shock resistant
Changeable LED (push-in design)
Environmentally friendly, hydro carbon-free LED lighting
Locking bulb-to-socket feature eliminates string loss due to loose bulbs
Average LED life: 100,000 hours
LED spacing: 4" +/- 1/4"
String length: 22' 6"
Lead length: 24"
Energy usage: 5 watts
DLR:
$21.25 Ea
To Order:
STEEL SAFETY CABLES, COMMERCIAL
LIGHT STRINGS
RSS
• Galvanized steel cable, 1/16", for use in outdoor mounting
of commercial light strings
• Load rating 100 lbs - use only for hanging light strings
DO NOT USE FOR SUPPORTING HUMAN WEIGHT
• Two shorter cables (60' and 110') have attached snap hook
on one end and loose cable clip for other end
• Cut cable to desired length with wire cutters
• No tools needed to use cable clips
• Cables and clips available as follows
#CBL60
#CBL110
#CBL350
#CBLGRP2
(
60' Cable w/Snap Hook and Cable Clip
110" Cable w/Snap Hook and Cable Clip
350' Cable on Spool, No Hooks or Clips
Steel Cable Clips
Call: (800) 233-0175
Fax: (717) 892-5981
Web: www.rssd.com
$27.00 Ea
40.50 Ea
127.50 Ea
5.70 Ea
2014 Party Products
Non-Food Service
RSS
DISTRIBUTORS
B
35
lighting
ANTIQUE STREET LAMPS
•
•
•
•
•
From the makers of the hugely popular rotomolded columns
Three different style heads for mounting on standard lamp post
For indoor and temporary outdoor use
Wiring is double-insulated two-prong (not UL listed)
Use lamp post stabilizer/riser to stabilize lamps in temporary setups
(adds 3" to height of lamps)
• Both black and white finishes standard on lamp post - other finishes
incur 10% upcharge
• Lamps available in following configurations:
#ARM-984
#ARM-989
#ARM-992
#ARM-904
Lamp Post w/13" Globe Diffuser (Black or White), 84" H $255.00
Lamp Post w/Acorn Diffuser (Black or White), 89" H
255.00
Lamp Post w/Coach Light Lantern (Black Only), 92" H
270.10
Lamp Post Riser/Stabilizer (Black or White), 3" H
76.10
Replacement Lamp Post Heads
ARM-984 w/
ARM-904
#ARM-1013
#ARM-1015
#ARM-1017
ARM-989
ARM-992
Poly Globe, 13", White
Acorn Diffuser, 15", White
Coach Light Lantern, 17", Black
ARM-904
PORTABLE POST LIGHTS
(LUMINAIRES)
#1601-00162
CHANDELIER,
FOUR GLOBES
Polymer Products
• Weather and impact
resistant superior outdoor plastic
• Single head light is 5' 10" high and has 14" globe - uses 100W bulb (not included)
• Four-head light is 6' 4" high and has three 6" and one 7.5" globes - uses 60W bulbs
(not included)
• All lights have a dimmer switch and an
8.5' outdoor cord
• UL listed for wet locations
• Four-head light available in white or
black; single head light in white only
• 6" globes available in white polycarbonate
or clear prismatic acrylic - 14" globes in
white acrylic only
Polymer Products
• Same weather and impact resistant superior outdoor plastic
used in portable post lights
• Chandelier includes three 6" and one 7.5" white polycarbonate
globes - uses 60 W bulbs (not included)
• Hangs from 20' white cord
DLR:$57.20
#1601-00163
POST LIGHT TO
CHANDELIER CONVERTER
Polymer Products
• Convert four-head or one-head post lights to hanging
chandelier
• Remove two screws and disconnect electrical leads to remove
head from post light
• Reattach electrical leads to converter and insert into open end
of head to use as chandelier
• Converter includes 20' white cord for
hanging chandelier
DLR:$17.30
TD
$53.00
55.85
73.10
#LUM1-D-WHT
#LUM4-DBLK-WHT
#LUM4-DBLK-CPR
#LUM4-DWHT-WHT
#LUM4-DWHT-CPR
Replacement Globes
#104A-L&L
#31-01-130-52230
#32-01-130-PCARB
#32-02-130-51630
#31-01-130-51630
RD
Single head light w/white acrylic globe
Four head light in black w/white
polycarbonate globes
Four head light in black w/clear
prismatic acrylic globes
Four head light in white w/white
polycarbonate globes
Four head light in white
w/clear prismatic acrylic globes
White Acrylic, 14"
White Polycarbonate, 7.5"
White Polycarbonate, 6"
Clear Prismatic Acrylic, 6"
Bronze Prismatic Acrylic, 6"
$87.25 Ea
126.60
126.60
126.60
126.60
$17.00
7.85
2.95
2.95
3.10
B
36
Party Products
Non-Food Service
RSS
2014
DISTRIBUTORS
LIGHTABLE PROPS
LIGHTABLE PROPS/FURNITURE
• From the makers of the Meese Orbitorn Dunne brand of columns, arches and accessories
• Rotomolded cylinders, cubes, spheres and a specially designed chair can be lighted from
inside with a battery powered LED light (See p. 37)
• An innovative seating, serving and display area concept - applications limited only by
imagination (see photos)
• All items manufactured from durable scratch and scuff resistant 100% polyethylene to
withstand the rigors of rental use
• Molded-in opening in bottom of each piece allows placement of light in each piece
• Clear, polycarbonate tabletops can be attached via three self-tapping screws to cylindrical
and square pedestals
• Five cylinders, five square pedestals, five spheres, two cubes, a block and other speciality
pieces available as follows:
Table: #ARM-52142 w/ARM-14126 & #ARM-FREST
DLR
#ARM-52118 Cylinder, 21" x 18" H
$118.65
137.40
167.55
178.40
191.60
#ARM-50042 Square Pedestal, 21" x 42" H
167.55
272.90
304.20
357.70
400.90
441.20
#ARM-53013 Sphere, 13"
53.00
62.90
125.20
158.20
258.55
#ARM-50004 Cube, 24"
142.90
#ARM-50001 Cube, 30"
215.20
#ARM-50002 Block, 12" x 12" x 20"
62.95
#ARM-41200 Chair
215.00
#ARM-50005 Cocktail Table, 24" x 18" H
105.15
#ARM-14125 Tabletop, Polycarbonate, 22" Round
74.95
#ARM-14127 Tabletop, Polycarbonate, 24" Round
72.00
#ARM-14126 Tabletop, Polycarbonate, 21" Square x 3/8" 58.55
#ARM-14129 Tabletop, Polycarbonate, 24" Square
61.95
#ARM-14130 Tabletop, Polycarbonate, 36" Square
292.80
#ARM-FREST Footrest, 21" Cylinders
202.55
See following page for LED prop lights
Note: Due to uncontrollable variables in the
manufacturing process, prop surfaces, including
the base surface on which the prop rests, may not
be perfectly smooth. This could result in minor
instability of the prop itself.
To Order:
(
Call: (800) 233-0175
Fax: (717) 892-5981
Web: www.rssd.com
2014 Party Products
Non-Food Service
RSS
DISTRIBUTORS
}
B
37
SPECIALTY LIGHTS
#AT-22810
E-RISERtm LED
COLUMN
FLORAL HOLDER
"AA" Battery
Powered
• Display centerpiece floral arrangements on this lighted LED
column for a spectacular effect
• Base Diameter: 9"
• Top pan: 8 1/2" w/1" recess
• Column: 25" tall x 1 1/2" diameter clear bubble-filled
acrylic
• Controls allow lighted column to be bright white, pink, teal,
blue, red, green, or to cycle RGB
• Power Source: "AA" Batteries (3)
• Battery Life: 8 hours
DLR:
$62.35 Each / $673.40 Case of 12
LED LIGHTS, LIGHTABLE FURNITURE
MULTI-COLOR
Fortune Products
• Use these battery-powered LED discs to light individual
pieces of lightable furniture
• Simply lay disc under hole in bottom of furniture piece
• Light base features 320 LED lights (80 red, 80
blue, 80 green and 80 white)
• Features a "slow color change" option
• "Stop" button can be used on slow change to fix a
specific hue for single color display
• Custom made to provide an even non-directional
glow similar to a light bulb
• Dimensions: 13.75" x 5.5" H
• Power Source: "D" cell batteries (8)
• Battery Life: 8+ hours
• Optional adapter available for A/C operation
DLR
#TSL-80RGBW
Light w/o Remote
$142.45
#TSL-80RGBW-RC
Light w/Remote
164.45
#TSL-320DM
Replacement Cover
6.40
#ADAP-LLAS1000
AC Adapter
8.70
LED
LED
PAPER LANTERN LIGHT
Fortune Products
COCKTAIL TABLE LIGHT
Fortune Products
• Turn your cocktail table cloth or spandex skirt into a beautiful illuminated
work of art that will dazzle your guests
• Light can be fixed on red, green, blue or white
• Will change colors automatically or can be set on combinations of colors
using the stop button as it changes from one color to the next
• 160 LED lights produce an almost infinite variety of hues
• Light attaches easily to cocktail table pole using supplied bracket
• Will attach to poles of 3/4" to 2" diameter
• Size: 4.25" x 11" D
• Uses four "D" batteries (not included)
• Batteries last 8+ hours
#CTL-160RGBW
#CTL-160RGBW-RC
#CTL-160-DM
#ADAP-LLAS1000
TD
Light w/o Remote
Light w/Remote
Replacement Cover
AC Adapter
$91.80
116.65
11.95
8.70
LED
• Turn your plain paper lanterns into lighted paper lanters
• Ornate paper lanterns suddenly become things of beauty
accentuating their design
• Use one lantern light, even for large lanterns
• Contains 12 super bright glowing white LEDs which produce a very
bright and even distribution of light like a light bulb
• Simply hang the lantern light from the lantern's upper wire framework
• Conveniently located on/off switch
• 7+ hours of illumination
• Takes 3 AAA batteries (not included)
• Remote sold separately
#PLL-12W
Light w/o Remote
#PLL-12W-RC
Light, Remote Capable
#PLL-1C-REMOTE Remote Control
RD
$3.35
6.15
3.95
B
38
Party Products
Non-Food Service
RSS
2014
DISTRIBUTORS
GEL PAPER and PAR ON BASE
STAGE and tent fixtures
GEL PAPER
PAR38Cb
• High heat gel paper for use with
all stage lights
PAR38CC
PAR56CC
PAR56Cb
PAR Fixtures
PAR fixtures use a PARabolic reflector, generally with a long
barrel design, to focus a beam of light on a particular spot.
As such, they represent economy-level stage lighting, and
are also commonly used for tent lighting
• PARs suitable for both stage and tent lighting
• Available with (Package Pricing) or without (Component
Pricing) lamps and clamps
• All fixtures include color gel holder and power cord
• Order color gels separately
• Other fixtures available, call for information
RD PACKAGE PRICING
DLR
#SL38F
PAR 38 Black Fixture, 120W Flood
$38.10
Lamp & Clamp
#SL38F-CR
PAR 38 Chrome Fixture, 120W Flood
38.10
Lamp & Clamp
#SL38S
PAR 38 Black Fixture, 120W Spot
38.75
Lamp & Clamp
#SL38S-CR PAR38 Chrome Fixture, 120W Spot
38.75
Lamp & Clamp
#SL38Q
PAR 38 Black Fixture, 250W Quartz
54.60
Lamp & Clamp
#SL38Q-CR
PAR 38 Chrome Fixture, 250W Quartz
54.60
Lamp & Clamp
#SL56
PAR 56 Black Fixture, 300W Flood Lamp 66.60
and Clamp
#SL56-CR
PAR 56 Chrome Fixture, 300 W Flood
66.60
Lamp & Clamp
#SL56Q
PAR 56 Chrome Fixture 500W Quartz
90.30
Lamp & Clamp
#SL56Q-CR
PAR 56 Chrome Fixture 500W Quartz
90.30
Lamp & Clamp
component pricing
DLR
#PAR38CB
PAR 38 Fixture Only, Black
$29.95
#PAR38CC
PAR38 Fixture Only, Chrome
29.95
#PAR38FL
PAR 38 Lamp, 120W Flood 4.45
#PAR38SL
PAR38 Lamp, 120W Spot
4.95
#PAR38QL
PAR 38 Lamp, 250W Quartz
20.25
#PAR56FL
PAR 56 Lamp, 300W/Med Flood
22.50
#PAR56QL
PAR 56 Lamp, 500W Quartz
48.00
#PAR56CB PAR 56 Fixture Only, Black
35.95
#PAR56CC
PAR 56 Fixture Only, Chrome
35.95
#SLO2
PAR 38, 56 Clamp
3.80
Note: Above fixtures are not UL listed. UL listed fixtures are available by special order for a significantly higher price. Please call for
a quote.
Stocking Colors
#SL99G-BLUE
#SL99G-GREEN
#SL99G-PINK
#SL99G-RED
#SL99G-YELLOW
Blue #119
Green #124
Pink #036
Red #106
Yellow #010
Other Available Colors
#SL99G-AMBER
#SL99G-FLESH
#SL99G-LAV
#SL99G-LGRN
#SL99G-LPNK
#SL99G-ORNG
#SL99G-PURPLE
#SL99G-ROSE
#SL99G-SBLUE
#SL99G-TURQ
Golden Amber #134
Flesh Tint #162
Lavender Tint #343
Light Green #122
Light Pink #035
Orange #021
Purple #339
Rose Purple #332
Sky Blue #118
Turquoise #115
Note: "Tint" gels are specially
designed for lighting people
DLR: $6.95 Sheet (20"x24")
DLR: $2.20 Patch (7.5"x7.5")
#SL-PAR38B
PAR ON
BASE
• PAR 38 mounted on economical and easy-to-use
wooden base
• Perfect for lighting arches, columns, and other
mood setting items
• Color frame permits changing
colors using standard theatrical
gel paper
• 120 W bulb included
DLR:
$47.20
#WB-PAR38
WOODEN BASE ONLY
• Bolt (provided) the "U-shaped
handle of any light fixture to this
base - provides solid base for
directing light as desired
DLR:
$12.65 Ea
#WB-HARDWARE
• Hardware set for wooden base
DLR:$.75
To Order:
(
Call: (800) 233-0175
Fax: (717) 892-5981
Web: www.rssd.com
2014 Party Products
Non-Food Service
RSS
DISTRIBUTORS
B
39
TENT LIGHTING AND lighting STANDS
#LTS-01
heavy-duty stand
•
•
•
•
•
•
Safety pins
8 mounting screws included
Load capacity: 100 lbs
Size: 9' fully extended
Tripod tubing diameter: 1 1/4"
Weight: 16.8 lbs
DLR:
$64.40
#LTS-31
PORTABLE TRUSSING
SYSTEM
•
•
•
•
•
•
•
#LTS-06
lightweight stand
Easy setup
Safety pins
T-bars
Load capacity: 200 lbs evenly distributed
10 ft. trussing span
Size: 9' fully extended
Weight: 46 lbs
DLR:
• Black anodized aluminum tripod w/4' crossbar
• Telescope to 9'
• Tubing diameter: 1.2"
• Load capacity: 50 lbs.
DLR:
$133.60
$38.65
STROBE LIGHTS
Fits in Gear
Bag CHS-40
Fits in Gear
Bag CHS-40
#st-2000s
TECHNO STROBE
Chauvet
•
•
•
•
•
•
•
•
•
•
75 watts
1-20 flashes per second/10 million-flash life
Linkable via mono cable (EST-MONO25FT)
Sound-activation
2 position switch - Audio (Sound Activated),
Flash
Size: 10.5" x 8.5" x 8.5"
Shipping weight: 7.9 lbs
Power: Switchable 110v/230v
1 year limited warranty
Optional Controller: #CH-751
DLR:
$59.99
Replacement Bulbs
#CH-1000B
TD
Bulb $11.35
#TECHNOSTROBE168
TECHNOSTROBE 168
Chauvet
#ministrobeled
MINI-STROBE-LED
Chauvet
Easy-to-use strobe light with 21 white LED's and
adjustable strobe rate. Plug-and-play right out of box, it
comes in a compact case and ready to use for your next
mobile DJ gig, party or anywhere you need a burst of
strobing white light
•
•
•
•
Ready to go out of the box
Manually adjustable strobe rate
Light source: 21 (white) LED's
Power and current: 120V, 60Hz,
1W
• Weight: 0.5 lbs
• Size: 5.1" x 4" x 3.7"
DLR:
$13.85
• Techno StrobeTM 168 is a white, 2-channel
DMX strobe light
• Built-in speed and instensity adjustments
• Perfect for a variety of applications and can
run all night long while utilizing very little
power
• Built-in automated and sound-activated pro
grams
• Light Source: 168 (white) @.25W (20mA)
LEDs 100,000 hrs
• Power and current: 28W, 0.2A @120V
• Weight: 2.3 lbs
• Size: 8.7" x 9.4" x 5.5"
DLR:
RD
$99.99
B
40
Party Products
Non-Food Service
RSS
2014
DISTRIBUTORS
MIRROR BALLS, TURNERS and pinspots
#PS-4
HANGING
PINSPOT
#10HT
MIRROR BALL
TURNER
(A.C.)
• Use two pinspots
to illuminate each mirror ball
• Suitable for 12", 16" or larger
balls
• Provides 4" diameter shaft of
light
• Includes Par 36, 4515 (30 watt,
6-volt) lamp
• Metal housing includes 6'
grounded line cord with fuse
• Colored lenses available
• Note: Clamp not included
• ETL listed
• 25 lb. capacity
• 110 volt a.c.
DLR:$10.10
GLASS TILED
MIRROR BALLS
• Genuine glass mirror tiles
• Balls have large number of small
reflective tiles, providing a
dazzling and colorful lighting
effect
• Available in 12" and 16" sizes
#MB12
#MB16
Size
12"D
16"D
DLR
$25.90
49.99
#3440-4R-3V-TC-SP
MIRROR BALL
TURNER
(Battery)
DLR:
• 12 lb. capacity
• Motor is lubricated for life and
sealed in rust-proof case
• Use two flashlight batteries
LAMPS AND LENSES
DLR:$35.95
#10007 Replacement
Battery Holder
$31.80
$3.75 Ea
#PS00L
#PS01-CL-SET
#PS01-CL-xx
#4515, Par 36 replacement $11.95 Ea
lamp for pinspots
Set of eight (8) colored lenses for use
9.30 Set
with pinspots. Includes amber, blue, green, light green, pink, purple, red, & yellow
Specific colored lens for use with pinspots 1.45 Ea
mirror ball packages
LED PINSPOT
#LED-PINSPOT2
LED PINSPOT2™
HANGING
Chauvet
LED
rental quality mirror ball packages
•
•
•
•
•
•
Includes mirror ball, turner and two pinspots w/clamps
Rig to piece of piping or other suitable structure to create desired effect
Mirror ball can be either 12" or 16"
Turner is #10HT a.c. turner or #3440-4R-3V-TC-SP d.c. turner
Pinspots are #PS-4 or #LED-PINSPOT2 hanging spots
Clamps are #SL02 light duty
#MBP12
#MBP12-DC
#MBP12-LED
#MBP12-DC-LED
#MBP16
#MBP16-DC
#MBP16-LED
#MBP16-DC-LED
12" ball w/a.c. turner and PS-4 pinspots $103.80
12" ball w/d.c. turner and PS-4 pinspots 126.80
12" ball w/a.c. turner and LED pinspots
116.65
12" ball w/d.c. turner and LED pinspots 143.40
16" ball w/a.c. turner and PS-4 pinspots 127.90
16" ball w/d.c. turner and PS-4 pinspots 150.90
16" ball w/a.c. turner and LED pinspots 142.95
16" ball w/d.c. turner and LED pinspots 164.30
To Order:
LED Pinspot2™ includes two front focal lens options to produce hardedge beams for a variety of applications. The LED Pinspot2TM is
extremely lightweight, at less than one pound and is powered by a
3W white LED. Includes multiple lenses to change beam angles
•
•
•
•
•
•
•
Beam angle: 6° (installed) 9° (included)
Lux (6°): 4,120 @ 2m
Lux (9°): 1,335 @ 2m
Light source: 1 (white) 3W LED 50,000 hrs
Power and current: 120V, 60Hz: 4W, 0.1A operating, 0.1A inrush
Weight: 0.9 lbs
Size: 7.6" x 4.2" x 5.9"
DLR:
(
$39.99
Call: (800) 233-0175
Fax: (717) 892-5981
Web: www.rssd.com
2014 Party Products
Non-Food Service
RSS
DISTRIBUTORS
B
41
MIRROR BALL EFFECTS
#SPHERION-WH-LED
SPHERION WH LED
American DJ
#hemisphere5.1
LED MIRROR BALL EFFECT
Chauvet
LED
The Hemisphere™ 5.1 produces a
dazzling multi-colored centerpiece effect
similar to a mirror ball
The Spherion WH LED produces an effect that is similar to a modern Mirror Ball. It features five bright 3-Watt white LED sources that project sharp
beams of light that slowly rotate and fill an entire room. The unit has a low
27W power draw and includes rubber feet and a removable hanging bracket
so the unit can be set on floor or table or hung from the ceiling.
• Produces razor sharp beams from 116 lenses that rotate from a high output
white LED source that fills a dance floor, ceiling or wall
• Beams of light slowly rotate 360° (continuous rotation - not sound active)
Specifications
• Beam angle: 270°
• Runs extremely cool! - NO DUTY CYCLES! - Run all night!
• Power Draw: 27W Max
• Long life LEDs (50,000 hr. rating)
• Dimensions: 12.75" x 8" x 16.76"
• Weight: 11 lbs
Fits in Gear
DLR:
$206.25
Bag CHS-50
See the
Spherion WH LED
in action
• Stand-alone multi-colored LED mirror ball effect
• Contains red, green, blue, white and amber LEDs
for maximum color options
• Motor spins in both directions and at variable speeds to create an ever changing star field
• Power link up to 25 units which saves time running cables and extension
cords
• Awesome sound-activitated programs dance to the beat of the music
• Built-in automated programs via master/slave or DMX
LED
Specifications
• Coverage angle: 360°
• Light source: 5 (1 red, 1 green, 1 blue, 1 white, 1 amber) 3W LEDs,
50,000 hrs
• Power and current: 120V, 60Hz 38W, 0.4A
• Weight: 6.4 lbs
• Size: 10.7" x 10.7" x 10"
• 2 year limited warranty
Fits in Gear
See the
Bag CHS-40
DLR:
$159.99
Hemisphere™ 5.1
in action
special effects lights
BOB™ LED SIMULATED
FLAME LIGHT
Chauvet
LED
#LED-MUSHROOM
LED MUSHROOMTM
There's no heat or flame, but the Bob™ LED simulated flame sure
looks real. The effect is created by 54 orange and 12 blue LED's
Chauvet
The LED Mushroom™ can cover an entire room with crisscrossing
beams from floor to ceiling and wall to wall. The updated classic fixture is ideal for mobile applications
•
•
•
•
•
•
•
•
•
•
•
LED
2-channel DMX-512 LED derby effect
Continuous rotation or back and forth motor control
Built-in automated programs via master/slave or DMX (rotation only)
Built-in sound activated programs via master/slave or DMX (rotation only)
High-power, 3W (730mA) LED's
Additional power output: max 37 units @120V
Coverage angle: 130°
Light source: 3 LED's (1 red, 1 green, 1 blue)
Power: 120V, 18 W
Weight: 5.4 lbs.
See the
Size: 12" x 8.1" x 8.7"
Fits in Gear
LED Mushroom
Bag CHS-40
in action
•
•
•
•
•
•
•
•
•
#CH-BOB-LED
#P210-SLCLOTH
TD
$60.75
7.50
Simulated Flame Light
Replacements Silks Kit
See the
Bob™ LED
in action
DLR:$99.99
Simulated flame effect with no heat
Continuous operation (no duty cycle)
Includes 3 legs for table support and chain for suspension
Light source: 66 LED's (54 orange, 12 blue)
Power: 120 V, 33 W
Weight: 5.1 lbs. (with legs); 4.8 lbs. (with chain)
Size: 14" x 14" x 31" (with legs); 12" x 12" x 30" (with chain)
Replacement fabric kits available
RD
B
42
Party Products
Non-Food Service
RSS
2014
DISTRIBUTORS
special effects lights
#ABYSSLED30
ABYSSTMLED3.0
#JELLY-COSMOS-BALL
JELLY COSMOS BALL
Chauvet
American DJ
Fits in Gear
Bag CHS-40
LED
• AbyssTM LED3.0 is an eye-catching, multi-colored, simulated
water effect light with countless uses. A high-power 15-watt
white LED shines through any environment with or without fog,
while two glass effect wheels and one dichroic color wheel can be
controlled individually for optimal projections and effects
• The ADJ Jelly Cosmos Ball features dual rotating balls that pro
duce multi-colored, sharp beams of light. The transparent balls
glow creating an exciting effect on their own. This effect is
powered by four 3-Watt, 3 in 1 RGB Tri Color LEDs. The fixture
has a variable speed adjustment knob to change the speed of rota- Features
tion. The ADJ Jelly Cosmos Ball offers a new twist on an old
• Creates a great-looking rippling effect in areas with or without fog
school lighting effect and brings pure lighting excitement to
• Individual control of the effect wheels and color wheel to achieve any desired
effect
any party.
Fits in Gear
Specifications
Bag CHS-40
• Sound Active
• Beam angle: 360 degrees
• Run all night - no duty cycle
• Power consumption: 18.4 W
• Long life LEDs (50,000 hrs)
• Rotation: Variable up to 35 RPM
• Dimensions: 13.5" x 5.5" x 10"
• Weight: 5 lbs
DLR:
• User-configurable stand-alone operation provides excellent control without
DMX
• Power linking saves time running cables and extension cords
Specifications
• Colors: 5+ white, continuous scroll at variable speeds
• Light source: 1 white 15W LED 50,000 hrs
• Power linking: 24 units @120V
• Weight: 6 lbs
• Size: 9.6" x 10.2" x 7.4"
See the
Abyss™ LED 3.0
• Approvals CE
See the
Jelly Cosmos Ball
in action
LED
in action
$149.99
DLR:
$169.99
Fits in Gear
Bag CHS-40
#RADIUS20
RADIUS2.0TM
#DERBYX
DERBY X
LED
Chauvet
Chauvet
• Multi-colored effect light that creates overlapping rings of light
Features
•
•
•
•
•
Contains red, green, blue, white and amber LEDs for maximum color options
Motor rotates back and forth at variable speeds to create cool effects
Power linking saves time running cables and extension cords
Sound activated programs that dance to the music beat
Built-in automatic programs via master/slave or DMX
Fits in Gear
Bag CHS-50
LED
• Projects randomly changing patterns of red, green and blue light
•
•
•
•
•
8 channel DMX-512 LED derby effect
Blackout/static/strobe
Built-in automated programs via DMX
Built-in sound activated programs via master/slave or DMX
Mount multiple units together with adjustable, optional bracket
(XBRACKET)
• Additional power output: max 27 units @ 120V (see manual for details)
Specifications
• Light source: 5 (1 red, 1 green, 1 blue, 1 white, 1 amber) 3W LEDs, 50,000 hrs
• Power linking: 20 units @ 120V
• Weight: 6.3 lbs
• Size: 10.5" x 13" x 9.6"
• Approvals: CE
Specifications
• Extra wide coverage angle: 96°
• Light source: 90 LEDs (30 red, 30 green, 30 blue)
• Power and current: 120V, 60Hz: 24W, 0.2A operating, 0.2A inrush
• AC power: Autoswitching 100V - 240V 50/60Hz
• Weight: 4lbs
See the
• Size: 11.9 in x 15 in x 7.4 in
Derby X
DLR:
DLR:
$149.99
To Order:
in action
(
$99.99
Call: (800) 233-0175
Fax: (717) 892-5981
Web: www.rssd.com
RSS
DISTRIBUTORS
2014 Party Products
Non-Food Service
B
43
LASER EFFECT LIGHTs
#MINLASERRGX20
MinTMLaserRGX2.0
#MINLASERRBX
min™Laser RBX
Chauvet
Chauvet
• Extremely compact, the MiNTM Laser RBX
projects thousands of red and blue beams covering a huge area and looking great with or without fog.
The color and rotation speeds can be set wirelessly with
the included remote control. Customize the effects by
controlling independently the red and blue diodes. The
MiNTM Laser RBX can be easily mounted to truss with
the included clamp-mounting adapter
• Min LaserRGX2.0 is an ultra-compact, plug-and-play laser.
The unit features a sleek, stylish housing and projects different
red and green laser effects onto any surface. Two convenient
mounting stands (with easy clamp mounting ability) and an infra
red remote control are included
to make set-up and operation a breeze
TM
Features:
Features:
• Extremely compact laser effects that project thousands of red and green beams
• Mount to truss with the included clamp mounting adapter-or sit on
table using the included double-bracket yoke
• Covers a huge area and looks great with or without fog
• Set the color and rotation speeds wirelessly with the included wireless
remote control
• Each includes 3 different mounting options to fit the style and mood of any event or party
• Sound-activated and automated programs dance to the beat of the music or run by themselves
• Extremely compact laser effects that project thousands
of red and blue beams
• Mount to truss with the included clamp mounting
adapter
• Motor spins in both directions and at variable speeds
to create many different looks
• Each includes 3 different mounting options to fit the
style and mood of any event or party
• Sound-activated and automated programs dance to
the beat of the music or run by themselves
Specifications:
Specifications:
• Light source: 532nm/50mW green laser diode, 650 nm/100mW red laser diode
• Weight: 0.7 lbs
• Size: 5.5" x 5.4" x 4.1"
• Approvals CE, FDA
• Light source: 450nm/80mW blue laser diode,
650nm/100mW red laser diode
• Weight: 0.7 lbs
• Size: 5.5" x 5.4" x 4.1"
• Approvals: CE, FDA
DLR: $99.99
DLR: $129.99
TD
RD
See the
MiN™ Laser RBX
in action
B
44
Party Products
Non-Food Service
RSS
2014
DISTRIBUTORS
LASER EFFECT LIGHTs
#BLI-MEZMERIZOR-4fx
mezmerizoR™ 3D RGB Laser
Blizzard Lighting
Fits in Gear
Bag CHS-40
The Mezmerizor™ 4FX is a high power class 3R 250mw RGB laser effect that aims to please with stunning aerial and 3D RGB
laser effects! It's packed with 120 static and more than 20 enchanting animated 3D patterns that are sure to elevate the level
of excitement at your event!
• Richly saturated colors from separate red/green/blue laser modules and a high speed 15,000 point per second scanner system generate smooth shapes, fast
moving aerial effects, plus totally awesome 3D animated effects such as the city scape animation, a halloween theme, an animated dancer, animals running,
birds flying plus more!
• Set or run 3D shapes, 3D animations, 3D galaxy shape effects or star field effects. Run a single effect or overlap the effects to run all "4FX" at the same time!
• Sound active mode, auto mode, DMX512 (15ch) and master/slave
• Microphone sensitivity adjustment knob
Control Options:
• Complies with US FDA CDRH laser safety standards 21 CFR 1040.10, 1040.11
Auto and sound activated programs
• Power consumption: 50W
available via dip-switches. For total
• Dimensions: 14.6" x 12.6" x 5.2"
control of patterns, use Obey-40
• Weight: 9.3 lbs
Controller
See the
See page 45
Mezmerizor™ 4FX
DLR: $359.99
in action
GOBO PROJECTOR
Fits VIP
Bag #CHS-40
LED
#GOBO-ZOOM-LED-20
GOBO ZOOM™ LED 2.0
Chauvet
Gobo Zoom™ LED 2.0 projects your message or custom image
anywhere you want it. Powered by a 15W LED, this powerful gobo
projector comes with 4 gels and 9 easily replaceable rotating gobos.
Heat-free LED power allows you to create custom gobos at home
from transparency material. Variable beam angles allows for crisp
focusing at a variety of sizes
• Manual zoom for short throw or long throw applications
• Includes nine popular gobos and four colored gels including Happy
Birthday, Happy Holidays and Congratulations
• Rotating gobo size: 28.6 mm outside, 26 mm image, 1 mm thickness
• Beam angle: 18-26°
• Illuminance: 1,027 lux @ 2m
• Weight: 4.4 lbs
• Size: 9" x 7.3" x 7.2"
How to make
DLR:
$169.99
your own gobo for the
Gobo Zoom™ LED 2.0
Fits in Gear
Bag CHS-40
#IKON-LED
IKON LED
American DJ
The IKON-LED is a high output single Gobo Projector powered by a bright
60W (7500K) white LED. This fixture uses high quality optics for crisp, clear
projection. User can adjust the LED brightness and Gobo rotation on the rear of
fixture or by the included wireless RF remote control.
The Ikon LED includes 4 metal Gobos. Users may also insert custom Gobos in
the fixture. This projector also comes with three interchangeable lenses that produce different beam angles (25, 32 or 43°) making it versatile for a wide variety
of applications.
•
•
•
•
•
•
•
•
•
•
•
Gobo size: 54mm; Viewable size: 30mm
Run all night - No Duty Cycle
Easy Gobo replacement access
Comes with 4 Gobos: ADJ, Happy Holidays, Happy Birthday and Congratulations
Manual focus
Very low heat output
Long life LED (Rated at approximately 50,000 hrs)
Includes RF Wireless remote
Power consumption: 83.6W max
See the
Dimensions: 9.5" x 8" x 8.5"
Ikon LED
Weight: 8 lbs
in action
LED
DLR: $499.99
To Order:
(
Call: (800) 233-0175
Fax: (717) 892-5981
Web: www.rssd.com
2014 Party Products
Non-Food Service
RSS
DISTRIBUTORS
B
45
LIGHTING CONTROLLERS
#OBEY-40
Controller
#OBEY-3
CONTROLLER
• Universal DMX-512 controller
Chauvet
Chauvet
•
•
•
•
•
•
•
•
•
•
•
192 DMX channels of control
6 sets of chases containing 240 scenes
Program fade and speed time into each step
Reversible sliders
Re-assignable channels
Sequential linking of chases
Grab any fixture on the fly
Beat activation, tap-sync and auto run
Polarity selector
3-space (3U) rack mount
Specifications
• Power DC 12V 500mA, 115V/60Hz
or 230V/50Hz
• Weight: 5.7 lbs
• Size: 19" x 3.5" x 6.7"
DLR: $119.99
The OBEY™3 is a compact DMX controller for LED lights
with three channels (red, green and blue only)
•
•
Playback options include automated, sound activated or manual RGB color
mixing.
Perfect controller for a lighting novice or someone who wants to easily
control their LED washes
•
•
•
•
•
•
•
•
•
•
Features
Manual color mixing (red, green, blue)
9 preset colors
Chase: Triggers automated programs
Macro: scrolls through the color spectrum
Variable fade times for all playback modes
Fader for master dimmer
Adjustable audio sensitivity
Weight: 2 lbs, Size: 5.5" x 8.3" x 2.1"
Note: Only works
with Slimpars and
other 3 Channel lights
DLR: $49.99
#DMX-T-PACK
DMX TERMINATOR KIT
American DJ
#OBEY-4
CONTROLLER
Chauvet
The OBEY™4 is a compact DMX controller for LED lights
with four channels (red, green, blue and white/amber)
• Use a DMX terminator at the end of each DMX
run to eliminate feedback interference in the
control of the run
• 110 Ohm terminators
• Kit includes one 3-pin male terminator and
one 5-pin terminator
DLR:
$7.95/Kit
#V-8000
power panel
• Use for on/off control of various fixtures such as strobes, mirror ball
motors, bubble machines, etc.
• Features eight lighted power switches on front panel, each controlling a
rear panel AC outlet
• Front panel mounted 15-amp circuit breaker for added protection
• Fitted for rack mounting
DLR:
TD
$25.65 Ea
• Playback options include automated, sound activated or manual RGB (A or
W) color mixing.
• Perfect controller for a lighting novice or someone who wants to easily
control their LED washes
•
•
•
•
•
•
•
•
•
•
Features
Lower
Manual color mixing (red, green, blue, white (or amber)
Price!
9 preset colors
Chase: Triggers automated programs
Macro: scrolls through the color spectrum
Variable fade times for all playback modes
Fader for master dimmer
Note: Only works
Adjustable audio sensitivity
with Slimpar 64 RGBA
Weight: 3 lbs, Size: 12.8" x 5.5" x 2"
and other 4 Channel
lights
DLR: $69.99
DMX CABLES
• DMX-512 compatible 3-pin cables used to
connect controllers to the intelligent devices
being controlled
#DMX3P25FT
#DMX3P12FT
#DMX3P10FT
#DMX3P5FT
RD
25' DMX 3 Pin XLR Cable $10.70
12' DMX 3 Pin XLR Cable 9.15
10' DMX 3 Pin XLR Cable 7.55
5' DMX 3 Pin XLR Cable
6.30
B
46
Party Products
Non-Food Service
RSS
2014
DISTRIBUTORS
LED WASHLIGHTS
WIRELESS DMX
SLIMPACK56
Chauvet
LED
Lower
Price!
The SlimPack56 bundles several popular products into an easily transportable
VIP gear bag. The package includes:
4 SlimParTM 56 wash lights, an ObeyTM3 DMX Controller and 4 10' DMX
cables conveniently packed in a specially made gear bag
• Size: 15" x 12" x 12"
#SLIMPACK56
#CHS-SP4 Travel Bag
$399.99
RD
29.99
See the
wiCICLE™
in action
wiCICLETM
Blizzard Lighting
Lower
Price!
wiCICLETM: The world's smallest wireless DMX interface (that we
know of!)
• Blizzard Lighting's wiCICLETM wireless DMX system is a powerhouse
in a tiny package!
• Not much bigger than a standard XLR connector, the wiCICLETM releases
you from the hassle of cable-fed DMX lighting
• wiCICLETM features 512 auto-assigning frequencies in 7 groups allowing
up to 7 systems to run simultaneously in the same space, completely free
of interference!
• Despite its small size, the wiCICLETM is one powerful system, capable of
reliable wireless communication for over 1000 ft, line-of-sight!
• With wiCICLETM wireless DMX has truly come out of the cold! Get yours
today!
Features
• Frequency - Agile 2.4Ghz wireless DMX system with 512 channels and 7
groups
• Ultra-compact form factor - no extra boxes, just plug and play!
• Very easy to use
• Up to 1000 feet transmission (line of sight)
• One transmitter can communicate with multiple receivers
#BLI-WICICLE
#BLI-WICICLE
#BLI-WIPAK
Transmitter
Receiver
Transmitter and Receiver Starter Pack
$134.99
134.99
251.99
#BLI-RGBAWPUCK-CP
THE PUCKTMRGBAW
Improved
for 2014
Blizzard
The PuckTMRGBAW: Every color imaginable - The original, super cool,
super affordable flat LED par can just got the ultimate couch potato
make over! Now you can kick back in your easy chair with total control
of all your new PuckTMRGBAW lighting fixtures using your IR wireless
remote control! wiCICLE® enabled
• Contains 198 10mm LEDs in red, green, blue, amber and white
• Includes 31 color presets. Operates in stand alone, auto programs or sound
active modes
• Ultra-thin with overall depth at 2.5" and a main depth of 1"
• LED control panel makes setting the light easy
• Daisy chain power for easy setup with less cables
• 2 year warranty
LED
• Variable electronic dimmer (0-100%)
• Built-in auto or sound active programs via master/slave
• Beam angle: 21° Field angle: 32°
• Lux: 2,995 @ 1m
• Power and current: 120V, 60Hz; 20W, 0.17A (operating), 0.17A (inrush)
• Weight: 4 lbs
• Size: 8.25" x 8.25" x 2.5"
Fits
in Puck Pack
DLR: $134.99
Rolly™ and Puck
Pack Carry™
See the
Gear Bags
Puck RGBAW
in action
To Order:
(
Call: (800) 233-0175
Fax: (717) 892-5981
Web: www.rssd.com
2014 Party Products
Non-Food Service
RSS
DISTRIBUTORS
B
47
LED WASHLIGHTS
#EZRAILRGBA
EZRAIL RGBA
Chauvet
Fits in Gear
Bag CHS-60
Lower
Price!
#COLORSTRIP-MINI
COLORstrip™ MINI
Satellite
Ready
Chauvet
EZrailTM RGBA is a battery-powered, linear wash light
designed for mobile applications where power is an issue.
A rechargeable lithium - ion battery powers all 160 LEDs
for up to 20 hours using a single charge. Perfect for area
washes or uplighting
Control options:
Remote control, DMX or LED
menu on back of light
Features:
• Achieve rich colors and pastels with amber LEDs
• Easily check the battery status with the built-in battery
life indicator
• Increase effects with 4 sections of individual control
• Convenient wireless, non-DMX operation with the included
IRC (infrared remote control)
• Built-in automated and sound-activated programs
Specifications:
$199.99 RD
#CHS-60
GEAR BAG FOR STRIP LIGHTS
Chauvet
•
•
•
•
•
Extremely affordable soft bag for strip lights
Internally padded compartments
Convenient handle and shoulder straps
Size (internal) 43" x 7" x 7.5"
Compartments: 2
DLR:
TD
DLR:
See the
COLORstrip™ Mini
in action
$99.99
Use #OBEY-40 Controller for
Colorstrip Mini and Colorstrip
LED
• DMX Channels: 2,4,5, 8, 10 or 18
• Light Source: 160 (40 red, 40 green, 40 blue, 40 amber)
0.25W (20mA) LEDs, 100,000 hours
• Field angle: 30
• Illuminance: 805 lux@ 2m
• Power linking: 32 units
• Power and current: 31W, 0.2A @ 120V 60 Hz
• Weight: 5.6 lbs
• Size: 19.9" x 2.9" x 6.1"
DLR:
• Mini version of Colorstrip
• Additional power output: max 20 units @ 120V
• Additional slave output allows for color changing runway effect (up to 31
units)
• Lux: 358 @ 2m
• Power and current: 120V, 60 Hz 38W, 0.3A operation, 0.2A inrush
• Weight: 3.3 lbs
Fits in Gear
• Size: 19" x 3.8" x 5.1"
Bag CHS-60
$29.99
Satellite
Ready
#COLORSTRIP
COLORstripTM
Chauvet
Lower
Price!
• Color wash wider objects at short distances
• 4-channel DMX-512 LED linear wash light
• Operating modes: Blackout and static/flashing colors, RGB color mixing,
Color fade
• Static colors and RGB color mixing with or without DMX controller
• Built-in automated programs via master/slave or DMX
• Built-in sound active programs via DMX
• Additional power output for daisy chaining units together (15 units)
• Master/slave mode with additional output for daisy chaining; allows for
color-changing runway effect (up to 31 units)
• Sound sensitivity knob
• Low power consumption
• Lux: 618 @ 2m
• Light Source: 384 (128 red, 128 green, 128 blue) LEDs 100,000 hrs
• Power and current: 120V, 60Hz, 72W, 0.6A operating 0.4A inrush
• Weight: 4.5 lbs (2 kgs)
• Size: 38" x 2.5" x 6"
Fits in Gear
See the
Bag CHS-60
COLORstrip™
DLR:
RD
$159.99 Ea
in action
Party Products
Non-Food Service
B
48
RSS
2014
DISTRIBUTORS
LED WASHLIGHTS
LED Lighting Advantages
1. Low Power, Low Heat - Produce the same amount of light as standard fixtures using only 10-20% of the power.
Corresponding low heat makes the lights fire marshall friendly.
2. Long Life - LED bulbs rated at 50,000 hours to 100,000 hours
3. Power Control Chaining - Provide power only to master unit. Daisy chain both power and control to other units.
4. Color Mixing - Produce the color your client needs through RGB (red, green, blue), or RGBA (red, green, blue,
amber color mixing - no more light reducing gels.
5. No UV Emissions - Safe for use in museum and art gallery venues where artwork is sensitive to standard lighting.
#SLIMPAR38
LED WASH LIGHTS
#SLIMPAR56
Now Available
in White or Black
Chauvet
#SLIMPAR64RGBA
#SLIMPAR64
Lower
Prices!
LED
• Low-power LED wash lights with relatively focused beams
• Built-in automated programs via master/slave, both standard and sound activated
•
•
•
•
Power linkable with other LEDrainTM, SLIMPAR and LED-SPLASH86B units (120V models only)
Double-bracket yoke also functions as floor stand
See the
SlimPAR™ 56
Four models available as follows:
in action
Control Options
Menu on back of
light
#OBEY-40 Pg B-45
#OBEY-3 Pg B-45
#OBEY-4 Pg B-45
(SLIMPAR64RGBA)
SLIMPAR38
SLIMPAR56
SLIMPAR64
SLIMPAR64RGBA
18
24
32
30
14
23
531
75
25/25/25 RGB
100,000
14
23
876
108
36/36/36 RGB
100,000
14
23
1,241
180
60/60/60 RGB
100,000
14
23
1,325
180
39/39/51/51RGBA
100,000
Electrical (V/A)
120 / .2
120 / .2
120 / .3
120/.3
240V Switchable
Weight (Lbs.)
Yes
1.8
Yes
2.7
Yes
2.8
Yes
2.8
7.3" x 8.1" x 2.5"
9.5" x 8.8" x 2.2"
9.7" x 11.1" x 2.5"
10.8"x10.8"x2.6"
50
50
40
40
#CHS-SP4
$69.99
#CHS-SP4
$79.99
#CHS-25
$99.99
#CHS-25
119.99
Watts
Beam Angle
Field Angle
Lux (@ 2m)
LEDs, Total
LEDs, Color
LEDs Life (Hours)
Dimensions
Power Linkable Units
Fits in Gear Bag
DLR
To Order:
(
Call: (800) 233-0175
Fax: (717) 892-5981
Web: www.rssd.com
2014 Party Products
Non-Food Service
RSS
DISTRIBUTORS
ledWASHLIGHTS
LED
#EZPAR64RGBA
EZparTM64RGBA
Chauvet
Fits in
Gear Bag
#CHS-25
EZ parTM64RGBA is a battery-powered wash light designed to
free the user from the hassle of running cables and speed setup.
The rechargeable lithium-ion battery lasts up to 20 hours on
a single charge and powers all 180 red, green, blue and amber
LEDs to deliver stunning colors. Easily keep tab on the remaining charge using the visible battery-life indicator, and add a
wireless receiver to create a completely wireless solution.
Features:
• Achieve rich colors and pastels using the amber LEDs
• Available with black or white housings
• Convenient non-DMX wireless operation with the included IRC
remote
• Built-in automated and sound-activated programs via DMX, IRC
remote or master/slave
• Fits easily in #CHS-25 VIP Gear Bag
Specifications:
49
LED WIRELESS WASHLIGHTS
THE PUCK Q6 UNPLUGGED
Blizzard Lighting
• The PUCK Q6A UnpluggedTM flat LED PAR can
features 6 state-of-the-art 10 Watt Quad-Color RGBA
LEDs which offer extreme output
and exceptional color mixing, even with hard to duplicate amber/
orange shades
• The PUCK Q6W UnpluggedTM flat LED PAR can features 6 state-ofthe-art 10 Watt Quad-Color RGBW LEDs which offer extreme output
and exceptional color mixing even with hard to duplicate pastels
• An LED control panel and power daisy chain connectors make it flex
ible and perfect for uplighting
• Auto or sound activated programs via stand-alone or master/slave
The Puck Q6 (A or W) Unplugged features 4 and 7 channel control modes
which means it works great with any type of controller, including popular
4-channel easy controllers. The built-in 4 character/4 button LED control
over the fixture including sound active and stand alone modes, display invert
and service hour readout
Control Options:
OBEY-40
OBEY-4
LED menu on back of light
Fits in
Puck Pack Rolly™
and
Puck Pack Carry™
Gear Bags or Blizzard
Charging Cases
Features
• Light source: 180 (45 red, 45 green, 45 blue, 45 amber) 0.25W
LEDs, 100,000 hrs
• Field angle: 23°
• Maximum run time (all on): Up to 8 hrs
• Maximum run time (single color): Up to 20 hrs
• Recharge time: 6 hrs
• Illuminance: 1325 lux@ 2m
• Power linking: 55 units
• Power and current: 33W, 0.3A
• Weight: 4 lbs
RD
• Approvals: CE
• Size: 10.8" x 10.8" x 2.6"
#EZPAR64RGBA-BLK
#EZPAR64RGBA-WHT
B
$199.99
199.99
• 4 or 7 channel DMX control or control with menu buttons on the back of
the fixture
• Dimensions: 8.5" x 5" x 8.25"
• Light source: 6 x 10W Quad-color LEDs, 60,000 hrs
• Field angle: 29°
Lower
Prices!
• LUX: 10,900 @ 1m
• Warranty: Fixture - 2 year limited
Battery: 1 year limited covering failure only
#BLI-Q6APUCK-UNPLUGGED
#BLI-Q6WPUCK-UNPLUGGED
$359.99
359.99
See
The Puck™
in action
CHARGING CASES
Blizzard Lighting
#BLI-P6CASE
#BLI-P12CASE
TD
RD
Holds six lights
$269.99
Holds twelve lights 359.99
B
50
Party Products
Non-Food Service
RSS
2014
DISTRIBUTORS
HIGH POWER LED WASHLIGHTS
Fits in
Pack-Puck-RollyTM
and Pack-Puck-CarryTM
Gear Bags or
Charging Cases
Fits in
Pack-Puck-RollyTM
and Pack-Puck-CarryTM
Gear Bags or
Charging Cases
#BLI-PUCKFAB5
BLI-PUCKFAB5
#BLI-PUCKFAB5-SKYWIRE
BLI-PUCKFAB5-SKYWIRE
Blizzard Lighting
Blizzard Lighting
Lithium-Ion Battery Powered + Built-In 2.4 GHz WIRELESS DMX!
Features:
• First ever PuckTM Flat LED par fixture loaded with 6 x 15-watt
RGBAW 5 in 1 LED's, a built-in skywireTM wireless DMX re
ceiver, and an internal Lithium-Ion battery system
• Features 3/5 and 12-channel control modes plus the built-in
4 character/4 button LED control panel allows total control over
the fixture, including master/slave auto mode, fade, strobe settings,
manual color/white point adjustment, sound active mode, display
invert and service hour readout.
• Lithium-Ion battery lasts up to 20 hours depending on color used
• Features built-in IEC power in/out daisy chain connections, 3-pin
DMX in/out connections, a main power and battery power switch
and an LED illuminated battery power gauge
• Wireless receiver provides reliable wireless communication for over
1000 feet, line-of-sight
• 2 year warranty
• Link up to 50 fixtures on 1 circuit
Specifications:
•
•
•
•
•
Beam angle: 25° Field angle: 29°
Flicker-free constant-current LED driver
Power consumption: 22W
Dimensions: 8.25" x 3.75" x 7.5"
Weight: 9 lbs
DLR:
Packed with 7 x 15W high power 5-in-1 RGBAW LEDs, the Puck Fab5TM
flat LED par can gives you the latest technology for a
fabulously low price!
Features:
• Superior internal RGBAW color mixing with an unmatched color gamut
• 3/5 and 12-channel control modes plus the built-in 4-character/4 button
LED control panel allows total control over the fixture, including
master/slave, auto mode, fade, strobe settings, manual color/white point
adjustment, 3 different sound active modes, display invert and service hour
read out
• IEC power in and daisy chain connections, 3-pin DMX connections and
LED control panel
• wiCICLE® enabled
• 2 year warranty
• Power link up to 50 fixtures
Specifications:
•
•
•
•
Beam angle: 25° Field angle: 29°
Weight: 4.2 lbs
Dimensions: 8.25" x 8.5" x 3.875"
DLR:
$229.99
$449.99
To Order:
(
Call: (800) 233-0175
Fax: (717) 892-5981
Web: www.rssd.com
2014 Party Products
Non-Food Service
RSS
DISTRIBUTORS
B
51
#BLI-PUCKV12
BLI-PUCKV12
Blizzard Lighting
LED
The PuckTM, the first ever flat LED par can has now been re-built
using the very latest 5 in 1 LED technology! 12 x 15 watt ultrabright 5 in 1 RGBAW LEDs have been placed in the ever stylish
cast aluminum chassis while also maintaining and adding to all the
same great features that made the original PuckTM series so popular!
Fits in
Gear Bag
#CHS-50 (3)
or Pelican Case
#PP-0350 (4)
Features:
•
•
•
•
•
•
•
•
12 15W, 5 in 1 RGBAW LEDS
Built-in automated programs via master/slave
User defined programs/scenes and upload feature
Preset or user adjustable white balance settings
Easy to use LED digital control panel
IEC power in and daisy chain connections to connect additional units
wiCICLE® enabled
Fits in
Specifications:
•
•
•
•
•
Beam angle: 25°, Field angle: 29°
Power and current: 114 watts
Weight: 4.2 lbs
Size: 8.25" x 3.875" x 8.5"
Lux: 14,730 @1m, 4,280@ 2m
Puck Pack Rolly™
and
Puck Pack Carry™
Gear Bags,
Pelican Case
#PP-1640 (6) or
Blizzard Road
Cases
DLR: $296.99
See the
The Puck™
in action
Blizzard Lighting
Use with lights that have
an IEC power input and a regular
3 prong power output.
• Power up your equipment with Cool CableTM brand IEC power cables!
• A rugged, affordable and simple solution to free yourself from extension
cords forever
• All cables are UL-listed and come with a lifetime warranty against
defects
Gauge Length
DLR
#BLI-MI-EC1625 16
25'
$19.99
#BLI-MI-EC1650 16
50'
29.99
#ECCOM-6
#ECCOM-10
#ECCOM-15
TD
Blizzard Lighting
ToughParFab5TM: Bringing 5 in 1 LED Color Mixing to the
Great outdoors!
• 1P65 rated for outdoor use
• Built from durable cast aluminum with a tempered glass lens
and water tight internal gaskets
• 7 x 15W LEDs bring beauty and light to all sorts of settings
• Industry first 32 bit user-selectable dimming curves bring
new subtlety and nuance to LED dimming
• Video safe at any resolution and frame rate
• Control the unit's many features including RGBAW color
mixing, strobe, ultra smooth flicker free 32-bit dimming,
10 auto run modes, or even 10 user-defined programs of up
to 30 steps with or without DMX
• 2 year warranty
•
•
•
•
•
•
•
•
•
•
•
$4.45
6.65
9.40
$359.99
EXTENSION CABLES
#BLI-DMX-EXT 3-Meter IP-Rated DMX Extension Cable
#BLI-PWR-EXT 3-Meter IP-Rated Power Extension Cable
#ECCOM-6
User defined programs/scenes and upload feature
Preset or user adjustable white balance settings
Menu key protection settings
Easy to use LED digital control panel
IP rated AC power cord and DMX in and out cables with caps
Dual bracket for flexibility in mounting
Light Source: 7 15W, 5 in 1 RGBAW Leds
Illuminance: 12, 420 LUX @ 1m, 3,520 Lux @ 2m (full on)
Beam angle: 25°, Field angle: 29°
Weight: 11 lbs
Size: 10' x 11" x 7.5"
DLR:
Use with lights that have
an IEC power input and output.
6' Black, 16/3 gauge
LED
Features
IEC POWER CABLE
IEC EXTENSION CORDS
#TOUGHPARFAB5
ToughParFab5TM
RD
$25.95
25.95
Party Products
Non-Food Service
B
52
RSS
2014
DISTRIBUTORS
FOLLOWSPOT
#LED-FOLLOWSPOT-75ST
LED FOLLOWSPOT
Chauvet
LED
LED
#BLI-TOUGHPARV12
ToughPARTM V12
Blizzard Lighting
Outdoor
Rated
Durable, High Performance 5 in 1 LED Par Can!
• The newToughParTMV12 is as tough as they come and can really pack
a punch
• This fixture offers superior color mixing abilities and brightness thanks
to its 12, 15W, high power 5 in 1 RGBAW LEDs
• 5 in 1 LEDs virtually eliminate shadows and uneven color within the
field
• Durable cast aluminum housing with tempered glass lens, watertight
internal gaskets and ease of use for a much lower price than other
fixtures in its class
• Run automatic or sound activated programs and full RGBAW color
mixing with or without DMX control
• Offers full RGBAW color mixing, 31 built-in programs and ultra smooth
flicker-free 32 bit dimming
Features
Fits in
• Variable electronic dimming and strobe
Gear Bag
• Built-in color and chase macros via DMX
#CHS-50 (3) or
• Light source: 12 x 15W 5 in 1 LEDs
Pelican Case
100,000 hours
#PP-0350 (4)
• Field angle: 30
• Dual mounting brackets for positioning
flexibility
• Totally silent convection cooling
• 1P rated AC power cord and DMX in/out cables with cable caps
• Size: 11.19" x 7.6" x 10"
• 2 year limited warranty does not cover malfunction caused by
damage to LEDs
DLR:
Powered by a 75 watt LED, LED Followspot 75 is a portable, compact and
lightweight fixture that creates a sharp edge and includes all the features of
a traditional followspot without the heat and lamp changes needed in the
past. There are seven colors plus white available at the push of a button
or by using DMX control. A mechanical iris and 14° - 20° zoom allow for
size and focus variation to create the perfect pool of light
Features:
• Super smooth LED dimming makes professional fading a breeze
• Single gobo slot projects crisp patterns onto any surface
• Setup and tear down in seconds with the included tripod stand
Specifications:
•
•
•
•
•
•
•
•
•
Gobo size: 23.7 mm outside, 21.3 mm image, 1 mm max thickness
Illuminance (14°): 8,140 @ 2m
Illuminance (20°): 4,650 @ 2m
Power and current: 215W, 1.8A @ 120V 60Hz
Weight: 13.3 lbs
Size: 22" x 10.8" x 11.5"
Approvals: CE, MET
Typical throw: 50 - 60'
Uses only 215W
DLR:
See the
LED Followspot 75ST
in action
#CH-W28
FOLLOWSPOT STAND
Chauvet
•
•
•
•
$512.99
To Order:
$499.99
3 locking casters
Safety pins
Mounting plate
Load capacity: 65 lbs
DLR: $62.95
(
Call: (800) 233-0175
Fax: (717) 892-5981
Web: www.rssd.com
2014 Party Products
Non-Food Service
RSS
DISTRIBUTORS
B
53
CARRY BAGs FOR LIGHTING
#CHS-25
GEAR BAG FOR LIGHTING
PUCK PACKTM
GEAR BAGS
Chauvet
• Fits 4 SlimPAR 64's or 4 AME-MEGA-GO-PAR64s
• The CHS-25 VIP gear bag is perfect for carrying a small system of
SlimPar64 sized fixtures along with control and cabling to go with it
• Each bag has padded internal compartments large enough to hold 4
SlimPAR™ 64 sized fixtures, a small controller and cables to connect
the system together
• Dividers are removable to accommodate various sized gear
• Five internal compartments and two external compartments hold
lots of accessories
• Internally padded compartments to help secure and safeguard your
investment
• Dimensions: (external) 15.7" x 12.4" x 11.2"
• Dimensions (per compartment) 11" x 10" x 2.5"
DLR:
$34.99
#CHS-40
Chauvet
• Soft-sided transport bag fits many of
Chauvet's most popular fixtures with a
removable divider to keep multiple units
packed safely in place
• Convenient side pockets allows for carrying
cables, clamps and other handy accessories
• One removeable divider creates one or two
separate compartments for greater flexibility
• Internally padded to help secure and safeguard
the fixtures during transportation
• Convenient handle and shoulder strap
• Dimensions (internal) 13" x 13" x 14"
DLR:
$19.99
#CHS-50
Chauvet
• Soft-sided transport bag fits many of Chauvet's
most popular fixtures
• Wheels and retractable handle make moving
heavier fixtures a breeze
• Three removable dividers keep multiple units
packed safely in place
• Convenient side pockets allow you to carry
cables, clamps and other handy accessories
• Four internal compartments and two external
compartments
• Built in wheels and retractable handle
• Three removable dividers
• Internally padded
• Dimensions (internal) 13" x 15" x 16"
DLR:
TD
$59.99
Blizzard Lighting
Got Pucks™? Then you need a Puck Pack™. Life on the road is tough.
Store and transport your Puck™ fixtures with ease, as well as keeping them safe and
looking good!
• The Puck Pack Carry™ is your answer if you're looking for a carrying bag for
any 4 Puck™ flat LED par cans.
• Your Pucks will feel safe between its 3 removable velcro padded
dividers. It also stacks just perfectly with the Puck Pack Rolly™.
• The Puck Pack Rolly™ will also hold any 4 Puck™ fixtures securely
between 3 removable velcro padded dividers and is equipped with a
removable suit case - style wheel/handle assembly.
• Combined with the Puck Pack Carry™, the Puck Pack Rolly™ serves as the
bottom half of an awesome 8 Puck™ rolling mobile solution!
• The Puck Pack Rolly™ also has a convenient front storage pocket to hold
any accessories you like!
• Both bags feature an impressive embroidered Blizzard Lighting Logo, are
very rugged and made from 600 denier black ballistic nylon material
#BLI-PP-ROLLY
#BLI-PP-CARRY
Dimensions
Rolling bag - 4 compartments
Carry bag - 4 compartments
DLR
$40.49
26.99
road cases
BLI-P6CASE
BLI-P12CASE
Puck Unplugged™ Case 6 or 12 - Securely holds 6 or 12 Puck Unplugged™
series fixtures and built in AC for easy charging!
• Cases are constructed with 3/8" plywood that's covered with a durable
ABS plastic exterior laminate
• Full-length steel piano hinge,
• Tapered aluminum edging steel ball corners
• 2x steel recessed handles with rubber hand grips
• Fitted with steel recessed butterfly latches
• Both cases sit on heavy-duty locking 3" casters and have steel recessed
caster cups on lid for case stacking
• Interiors lined with thick foam and fitted with six Power Con® compatible plugs
• 6 or 12 Power Con® compatible AC adapter cables included to plug in all
fixtures
• Simply plug the 5' main AC cord that's located in a rear compartment of case to
a standard AC outlet to charge up all of your fixtures
#BLI-P6CASE
#BLI-B12CASE
RD
Dimensions
DLR
36"W x 16 1/2"D x 19 1/2"H (including wheels) $269.99
36"W x 28"D x 17 1/2"H (including wheels)
359.99
B
54
Party Products
Non-Food Service
(
RSS
2014
DISTRIBUTORS
CARRYING CASES FOR LIGHTING EQUIPMENT
Replacement Foam
#PP-1640
Watertight
pelican cases
Pelican Products
Case Specifications
#PP-0350
Lifetime
Guarantee
Crushproof
• Customizible heavy-duty carrying cases to protect your most valuable equipment (such as deluxe LED
wash lights)
• Watertight, crushproof and dustproof (see warranty inset)
• Heavy-duty plastic construction with open cell core and solid wall design produces very strong, yet
lightweight case
• Easy-open, double-throw latches secure lid
• Automatic pressure equalization valve
• Stainless steel hardware and padlock protectors
• Personalized nameplate service available (return order card packed with each case)
• Lifetime guarantee of excellence
YOU BREAK IT,
WE REPLACE IT.....
FOREVER
Pick 'N Pluck Foam Fillers
• All cases have a layer of foam on the bottom, a layer of "egg crate" foam under the lid, and 3 to 5 layers
of Pick 'N Pluck foam in between
• Pick 'N Pluck foam is pre-scored into small squares - simply pull out and discard squares to form customsized holes for snug fit to your equipment
#pP-1640
#pP-0350
• Great case for carrying six (6) Puck V12
or (6) Puck Q6 Unplugged wash lights
• OD: 27 1/4" x 27 1/2" x 16 1/4"
• ID: 23 3/4" x 24" x 14"
• Pick 'N Pluck: 3 levels
• Fold-down handles
• Polyurethane wheels w/retractable handle
• Weight: 38 lbs
DLR:
Pelican products are guaranteed
for a lifetime against breakage
and defects in workmanship.
Simply send them a broken case
and they will replace it at no
charge.
• Great case for carrying four (4) ToughPAR
wash lights
• OD: 22 1/2" x 22 1/2" x 21 1/4"
• ID: 20" x 20" x 20"
• Pick 'N Pluck: 5 levels
• Large, two-person fold-down handles
• Weight: 32 lbs
DLR:
$296.95 RD
$330.75 RD
#pP-1641
REPLACEMENT FOAM
#pP-0351
REPLACEMENT FOAM
• Reconfigures your case for different
equipment or replace worn foam
• Reconfigures your case for different
equipment or replace worn foam
DLR:
DLR:
$116.10
To Order:
(
$130.80
Call: (800) 233-0175
Fax: (717) 892-5981
Web: www.rssd.com
2014 Party Products
Non-Food Service
RSS
DISTRIBUTORS
B
55
FOG MACHINES AND FLUID
#GEYSER RGB
GEYSER-RGB
fog machine
Chauvet
Make a statement with GeyserTM RGB - a unique effect fogger that adds a touch of drama to any performance
• This powerful fogger blasts a vertical stream of
safe, water-based fog while simultaneously illuminating
it with 21 high power (3W Tri-color) LEDs
• A combination of red, green and blue LEDs
allows you to easily mix the perfect color to
illuminate the fog
• Produces a pyrotechnic-like effect by emitting
25 foot-high blasts of color, fog and light
• Wireless control of independent colors using the
included remote
• Easily set DMX functions and stand-alone settings
using the digital display
• Tank capacity: 0.7 gallons
• Heat-up time: 4 min.
• Output: 17,000 cfm
• Power and current: 1500W
• Weight: 21 lbs
• Size: 18.7" x 12.5" x 7.8"
See the
DLR:
$399.99
#h1300
HURRICANEtm 1300
fog machine
Chauvet
#H1100
HURRICANETM 1100
fog machine
Chauvet
•
•
•
•
•
•
•
•
•
•
•
•
•
Medium-sized water based fog machine
Output: 8,000 cfm
Tank capacity: 2.75 Pints
Fluid Consumption: 8.2
Pints/Hr (continuous on)
Warm-up time: 5 minutes
Manual fog button
Low fluid indicator w/auto
shut down
Wired remote included
LED illuminated tank
Electrical: 120V, 774W,
5.9A
Weight: 8.4 lbs
Dimensions: 10.2" x 9.5" x 8.9"
DLR:
$99.99
Geyser™ RGB
in action
Most
Popular
Size!
• High output water based fog
machine
• Output: 20,000 cfm
• Tank capacity: 7 Pints
• Fluid Consumption: 16 Pints/Hr
(continuous on)
• Warm-Up Time: 5 minutes
• Manual fog button
• Low fluid indicator w/auto shut
down
• Wired timer remote included
• LED illuminated tank
• Electrical: 120V, 1328W, 11.2A
• Dimensions: 16.7" x 12.5" x 12"
DLR:
$149.99
FOG FLUID
Timer Remote
• Water based for use in two
fog machines above
• Produces thick white fog that
is clean and dry with minimal
odor
Wireless Remote
#FOGFL-12P Cs/12 pts. $39.95
#FOGFL-4G Cs/4 gal. 48.90
#FC-T Fogger timer remote $25.20
#FC-W Fogger wireless remote 25.20
MSDS
available at
www.rssd.com
For Clogged Fog Machines
Try a quart of #UNCLOGIT, a solvent especially designed to unclog fog machine plumbing - $3.60 per quart
TD
RD
B
56
Party Products
Non-Food Service
RSS
2014
DISTRIBUTORS
SNOW MACHINE
#SNOW FLURRY
SNOW FLURRY
#SNOW-GAL
SNOW GAL
American DJ
VEI
Lower
Prices!
• High output Snow Machine with timer remote
• Timer remote allows control of: duration of output, interval between output blasts and
constant output
• Choose from two settings on the timer
1. The continuing time can be controlled from 1-10 seconds
2. The interval time can be controlled from 10 seconds to 5 minutes
• Volume selection switch - choose between low or high snow output
• Intelligent Pump Protection (IPP) Pump automatically shuts off when snow fluid gets
too low; prevents damage to pump from running dry
• Includes hanging bracket
• Use immediately - No warm-up required!
• 1-quart removable snow fluid container
• Output: 60~90 m1/min
• Tank capacity: 1.5 liter
• Fluid Consumption Rate: 16~11 Min./Liter (100% output) 14 Min./Liter Average
• Dimensions: 15.25" x 7" x 6.25"
• Weight: 11 lbs
• Specially formulated for use in
Snow Machines
• Create bigger, denser, better
floating snow
• Available in 1-gallon containers
DLR:$57.60 Case/4 Gal.
See the
Snow Flurry
in action
DLR:$129.99
MSDS
available at
www.rssd.com
BUBBLE machineS
#BM11
BUBBLE MACHINE
Chauvet
Most
Popular
• Simple to use; Fill with
Bubble Juice, plug it in
and it's ready to go
• Produces mountains of bubbles
• Uses approximately one quart
of juice per 45 minutes
continuous operation
• Tank capacity: 1 quart
• Dimensions: 12.5" x 7" x 6.5"
DLR:$79.99
#B-550
BUBBLE KING
Chauvet
BUBBLE JUICE
•
•
•
•
•
•
•
#BM03X Case of 12 quarts $69.30
#BM04X Case of 4 gallons 46.20
Three double wands
Manual bubble button
Large version of BM11
Power: 110v or 230v
Shipping weight: 13.2 lbs
Size: 19" x 15" x 12"
1 year warranty
• Works in all bubble machines
• Heavy liquid produces large
quantities of bubbles
MSDS
available at
www.rssd.com
DLR:$159.99
To Order:
(
Call: (800) 233-0175
Fax: (717) 892-5981
Web: www.rssd.com
2014 Party Products
Non-Food Service
RSS
DISTRIBUTORS
HEAVY DUTY POLE CLAMP
B
57
MOUNTING ACCESSORIES
Swampy Hollow Manufacturing
CH-5
SL03
SL02
PIPE CLAMPS, "C" STYLE
Lower
Prices!
Closeout
• All metal clamps for attaching lights to stage pipes, tree stands
and trussing.
• Medium and heavy duty as follows:
#SL02
Pipe Clamp, 2" Throat Medium Duty 55 lbs
#SL03
Pipe Clamp, 2" Throat Heavy Duty 110 lbs
#CH-5
Safety Cable, 29" L
700 lbs
DLR
$3.80
9.45
2.85
• Rubber lined for extra grip and prevents scratching
• Available in nine sizes as follows:
Round Poles - 2 Mounting Points
Part#
Usage
#SH-CLAMP2-3-2MP 2" - 3" Tent Poles
#SH-CLAMP3-45-2MP 3" - 4 1/2" Tent Poles
#SH-CLAMP45-6-2MP 4 1/2" - 6" Tent Poles
DLR
$18.00
19.00
22.00
Round Poles - 1 Mounting Point
#SH-CLAMP3-45
3" - 4 1/2" Tent Poles
#SH-CLAMP45-6
4 1/2" - 6" Tent Poles
18.00
19.00
Square Poles - 1 Mounting Point
#SH-SQCLAMP2-3
2" - 3" Square Tent Poles
#SH-SQCLAMP45-6
4.5" - 6" Square Tent Poles
16.00
18.00
SL0512
PIPE CLAMP, "O" STYLE
• Round clamp attaches firmly to poles without marring
• Clamp fits 1", 1 1/2" and 2" poles
#SL0512
For 1", 1 1/2" & 2" poles
75 lbs
DLR
$7.90
tent pole mounting accessories
velcro strap kits
• Use two velcro straps to secure "L" bracket to tent pole
• Straps are sized to diameter of tent pole
• Loop strap through plastic buckle, pull tight and fasten
to itself
• Each strap rated at 45 lb. shear stress
• "L" bracket has hole for attaching standard
light fixture - provides full 360 degree
maneuverability
Closeout
• Available in black or white - specify color
Part#
#VELCNCH-105
#VELCNCH-120
#VELCNCH-150
#VELCNCH-180
#TLBRACK
For Pole
Strap
DLRDLR
Diameters
Length*
(1-99)
(100+)
1 3/4" - 2 1/8" 10 1/2"
$1.70 Ea
$1.50
2 1/8" - 2 5/8" 12"
1.75 Ea
1.55
2 5/8" - 3 1/2" 15"
1.90 Ea
1.70
3 1/2" - 4 1/4" 18"
2.00 Ea
1.80
"L" - Shape Mounting Bracket 6.50 Ea
N/A
*Note: Strap length includes 4" on end of strap for looping
back through buckle and fastening to itself
TD
CLP-25
CLP-06
CLP-15
DLR
#CLP-06 Heavy duty clamp with extension, 2"
220 lbs
$12.60
#CLP-15 Heavy duty clamp 2" poles
660 lbs
13.25
#CLP-25 Double heavy duty clamp for mounting
T-Bar to tent pole, 2"
880 lbs
18.90
#WB-PAR38
WOODEN BASE
WITH HARDWARE
DLR: $12.65
• For mounting wash lights
#WB-HARDWARE
• Hardware set for wooden base
DLR: $.75
RD
B
58
Party Products
Non-Food Service
RSS
2014
DISTRIBUTORS
MOUNTING ACCESSORIES
#TRAC-CLAMP-S
#tRAC-CLAMP-R
"R" Style Clamp
"S" Style Clamp
PIPE CLAMPS, KEDER STYLE POLES
RSS
• Clamps are specifically designed to be used with Keder style
square tent poles with embedded track
• Clamp seats in opposite sides of Keder track - hand tighten to
lock at desired position - no tools needed
• Clamps work with poles from 1.5" to 4.75" square
• "S" clamp provides for single point attachment to pole at desired position
• "R" clamp is for rigging trusses or larger items in your structures - middle
support accepts a shackle or spanset
• "T" clamp attaches 48" L x 2" D bar (included) to pole - lights
then attach to bar
• All clamps are heavy gauge aluminum with steel hardware
Part #
#TRAC-CLAMP-S
#TRAC-CLAMP-R
#TRAC-CLAMP-T
Description
"S" Style Clamp
"R" Style Clamp
"T" Style Clamp w/Bar
Capacity
50 lbs
300 lbs
150 lbs
"T" Style Clamp
Caution
Do not exceed the load capacity of
the beam to which the Trac Clamp
is attached, which may be less than
the clamp rating.
DLR
$40.95 Ea
79.00 Ea
142.00 Ea
PORTABLE EXIT SIGNS
#SLIM-COMBO
PORTABLE EXIT SIGNS
RSS
•
•
•
•
•
•
A truly portable solution for Exit/Emergency lighting requirements
Built-in LED strip provides back-lighting for sign
Powered by long-lasting NiCad batteries
Exterior switch provided easy on/off capability
Universal hanging lanyards provide for easy attachment to tent poles, etc
Unit includes foam-lined case for safe and easy transport
DLR:
To Order:
$230.50 RD
(
Call: (800) 233-0175
Fax: (717) 892-5981
Web: www.rssd.com
2014 Party Products
Non-Food Service
RSS
DISTRIBUTORS
B
59
BINGO
#BD-15345BL
CLASSIC INK™ BINGO MARKER
•
•
•
•
•
#BP-4-9000
BINGO PAPER
#DS5025
LARGE BINGO CAGE
• 13" diameter cage: 1/8" brass
plated wire; automatic ball
dispenser and chute
• Full set of ping-pong size
numbered balls
• Molded masterboard included
DLR: $115.20
• Bingo cards on paper
• Cards are 4" square
• Cards do not repeat within a
case (9000 cards)
• Cards are:
3 cards per sheet
750 sheets per pack (2250 cards)
4 packs per case (9000 cards)
• Sold by pack or by case
DLR: $9.50 Pk
102.60 MP
BINGO CARDS
RSS
DLR:$16.00 Pack
58.40 Case
#1170
BINGO MARKERS
• 3/4" diameter, plastic chips
• 1000 per bag
DLR:$9.50/bag
REPLACEMENT BINGO PARTS
• Replace lost and/or damaged balls and/or masterboards
#DSPPB
#DS5025P
#DS7102
#DS5022P
Lower
Price!
New concept in bingo ink
Comfort grip bottles
Capacity: 4 Oz
Color: Premium Blue
Sold in packs of 12 and master packs (MP) of 144
Set of ping-pong balls, numbered
Masterboard for ping-pong balls
Set of wooden balls, numbered
Masterboard for wooden balls
• Easy-to-read cards are light-duty cardboard in 8" x 9" size
• Slide cards feature fingertip shutters to cover numbers
Pkg
Count
#BC-LRGFACE Jumbo size easy-to-read cards
100
#BC-STDHARD Standard size hard cards
100
#DSSC
Slide cards
100
$26.25
15.75
16.20
8.90
raffle drums
CHUCK-A-LUCK
RAFFLE DRUMS
• Brass-plated drum mounted on brass wire
stand
• Hinged door on drum allows access to
tickets
• Drum turns easily using handle on righthand side
• Four sizes available - "Large" drum
handles most raffles, order others as
needed.
Description
Ticket
DLR
Capacity
#DS5021
Small, 11" x 8" x 12" H
1,000
$69.00
#DS5020
Large, 20" x 15" x 24" H
10,000
156.00
#DS5019
Jumbo, 20" x 20" x 24"
15,000
214.60
RD
#DS5019-1 Super-Jumbo, 24"x36"x 51"H
30,000
555.00
TD
DLR
$78.40 Pk
48.90 Pk
119.00 Pk
#DS3011
CHUCK-A-LUCK CAGE
• Layout. numbers 1-6 and three dice included
• 18" high wire cage
• Payoff on numbers on dice
DLR:
RD
$129.95
Party Products
Non-Food Service
B
60
RSS
2014
DISTRIBUTORS
gaming tables
#BJ-4
#CT-3
#RT-5
• All tables handcrafted in the Pennsylvania Dutch country
• Table surfaces are heavy plywood covered with standard felt layout
• Padded railings are covered with black automotive carpet, an
attractive surface that is highly resistant to scuffing and tearing
• All tables have folding legs, 30" height
#TH-6
#TH-6
TEXAS HOLD-EM
TABLE
#BJ-4
BLACKJACK TABLE
#RT-5
ROULETTE TABLE
#CT-3
CRAPS TABLE
• Large enough for 7 to play
(72" x 36")
• Padded rail on player side of
table
• Includes built-in 360-chip tray
(78" x 36")
• Padded rails on two sides of table
• Wheel cutout sized to hold
standard 18" wheel (not included,
RSS Part #18ROL)
(67" x 31")
• Padded rails on all four sides of
table
• Protective metal facing strip over
upholstery on side edge
• Large enough for 8-10 players
(87" L x 42" W)
• Padded rail around entire
perimeter of table
DLR: $339.00 RD
DLr: $329.00 RD
DLr: $559.00 RD
DLR:
ROULETTE WHEEL
RSS
$359.00 Ea RD
casino layouts
#MC-TH
TEXAS HOLD-EM
LAYOUT
#18ROL
ROULETTE WHEEL,
DELUXE
RSS
RSS
BLACKJACK, CRAPS,
ROULETTE LAYOUTS
•
•
•
•
• Color layouts screened onto
green felt
• Standard 3' x 6' size
• Use part numbers as follows
18" diameter
All steel spinner plate
Heavy bakelite base
Precision bearings
DLR: $248.50 RD
#MC-BJ
#MC-CR
#MC-ROL
DLR:
Blackjack
Craps
Roulette
$19.50
• Felt layout for hughly popular Texas
Hold-Em poker game
• Size: 3' x 7'
• Game instructions included
DLR:
RSS
•
•
•
•
An economy double-sided felt layout
Texas Hold-Em on one side, Blackjack on the other
Size: 3' x 6'
Game instructions included
DLR:
To Order:
(
$19.50
#MC-TH2
TEXAS HOLD-EM/
BLACKJACK LAYOUT
$22.90
Call: (800) 233-0175
Fax: (717) 892-5981
Web: www.rssd.com
2014 Party Products
Non-Food Service
RSS
DISTRIBUTORS
B
61
CASINO ACCESSORIES
#DS5011
ON/OFF PUCK
• For craps table
• 2" diameter
DLR:
$3.95
#MC-RM
ROULETTE
MARKER
• Polished Lucite
DLR:
$5.95
#DS5013
PLAYING CARDS
#6DK
DEALER'S SHOES
• Holds 6 decks of cards
• Full weight steel roller
• 1/4" polished clear Lucite
DLR:$33.00
• Casino first quality used cards
• Cut corners
#MC-DICECHIP
CASINO CHIPS,
EXTRA HEAVY
DLR: $22.50 Dz
• Extra heavy, 11.5 gram diamond
chips
• 1.5" D, 3/16" thick
• Available in five colors: Red,
White, Blue, Black and Yellow
• Sold 100 per box
#4DH
DISCARD
HOLDER
DLR:
$14.60 Bx
STOCK ROLL TICKETS
• For Roulette Wheels, 5/8"
• 2,000 tickets per roll (single or double)
• 10 rolls per case
$3.75
• Can be used loose or can be
fastened to table
• 1/4" polished clear Lucite
• For built-in use
• Holds 360 or 500 chips
• Black Plastic
15 3/8" x 6 1/4",
360 chips
$14.25
18 7/16" x 8 3/16",
500 chips
18.95
#1445D-10
DOUBLE ROLL
#1445S-10
SINGLE ROLL
$7.50
• Two-part, double numbered
• Rolls randomly drawn from two
color groups: white, yellow
green, pink, dark pink, red, blue
and orange
CHIP TRAYS
TD
$24.40
TICKETS
DLR:
#350ct
#500CT
• Top quality
• Precision molded
• Set of five (3/4")
DLR:
#RB-58
EXTRA
BALLS
DLR:
#MC-DI
DICE
DLR: $36.75 Cs
DICE CUPS
#DS7100
TICKET HOLDER
• Inside dimensions: 2.75" D x3" H
• Basic black vinyl and deluxe
brown leather
#DS5010-2 Basic
#DS5010
Deluxe
DLR: $18.75Cs
• Brass plated
• Dispenses single or double roll
tickets
DLR:
$5.95
9.95
• One-part, labeled "Admit One"
• Rolls randomly drawn from color
group of white, yellow, green,
pink, dark pink, red and blue
RD
$23.95
B
62
Party Products
Non-Food Service
RSS
2014
DISTRIBUTORS
carvinal games
Product Specifications
• All game boxes constructed from 3/4” birch plywood except where noted
• Game boxes can be painted in any of 30 colors and are sealed with three
coats of polyurethane - weather resistant
• Game boxes easily assemble and disassemble for storage and transport using
“R” pin (no tools required)
• All games UPSable except where noted
• All parts replaceable
#RAB-3X3
RING A BOTTLE GAME
Jack's Games
•
•
•
•
Classic "Ring A Bottle" game in a 3' x 3' floor model size
Table designed to hold 49 standard size bottles
Sloped "ring ramp" returns misses to one side of game
Bottles not included
DLR: $473.50 Ea RD
#RABAT
RING A BAT GAME
#ROAS
RING ON A STRING
• Tabletop model measures
30” x 28” x 24” H
• Game features 33 7” baseball
bats vertically mounted on five
rails
• Includes 36 1 3/4” plastic rings
• Tabletop model
• Throw the ring onto a hook on the
backboard to win
DLR: $394.75 Ea RD
DLR: $263.00 Ea RD
Jack's Games
Jack's Games
#JGSA
SPIN-ART MACHINE
Jack's Games
• Enclosed turntable rotates card as paint is squeezed onto it from above
• Safety screen in top lid prevents paint bottles from being dropped onto
moving cards
• Motor stops turning when top of unit is opened
• 110 volt operation
• Compartment in back of box holds over 50 cards and frames
• Box constructed from 1/2” plywood, measures 15” W x 21” D x 10” H
• Game includes 50 cards (5" x 7") and frames and four empty paint bottles
DLR: $342.00 Ea RD
ACCESSORIES
#JGSA-CF5
Cards and Frames, 500/Cs
#JGSA-PNT
Paint Liners, 25/Cs
(Throw-Away Box Protector)
$142.00 Cs
26.25 Cs
To Order:
#PLINKO
PLINKO GAME
Jack's Games
• Player wins with "three in a row" on bottom line; or player
wins by matching target sum on bottom line
• Constructed from 3/4" birch plywood
• Sealed with three coats of polyurethane - weather resistant
• Free standing - back legs fold flat against game board for storage and
transport
• Size: 2' x 4'
DLR:
(
$421.00 Ea RD
Call: (800) 233-0175
Fax: (717) 892-5981
Web: www.rssd.com
2014 Party Products
Non-Food Service
RSS
DISTRIBUTORS
B
63
carvinal games
#TCT
TRASH CAN TIPPING
Jack's Games
#PAP-GA
GOLDEN EGG
(PULL A PRIZE) GAME
Jack's Games
• Tabletop model
• Features two shelves holding
base weighted "crazy" trash
cans
• Tip cans by tossing soft "hacky sack" ball to win
•
•
•
•
DLR:
DLR:
$289.50 Ea RD
Tabletop model
Game board contains 32 holes covered so that they hide contents
Each hole contains an egg, but only four are golden
Reach in, pull out an egg and see if you win
$447.50 Ea RD
#JGCS
#TCALLEY
COVER THE SPOT GAME TIN CAN ALLEY GAME
Jack's Games
Jack's Games
• Game board measures 12” x 12”
• Player tosses five 4.5” discs - wins
if 7” spot on board is completely
covered by discs
• Tabletop model measures 30” x
30” x 24” H
• Game features 18” high pedestal
which holds six stacked tin cans
• Knock all cans completely off
pedestal with two bean bags to win
• Cans and bean bags included
DLR: $63.00 Ea
DLR: $421.00 Ea RD
#HI-PAP
HOOP-IT/PICK-A-POP GAMES
Jack's Games
• Game box measures 18” x 18” x 6” H - supports two different
games
• For Hoop-It games, place prize in box (on 1/8” white tile board
secured against 12” pipe) - player must ring prize and entire
game box with 24” hoop to win
• Reverse sign on game box to set-up Pick-A-Pop games - fill 1/ 8” peg
board (provided) with approximately 250 lollipops, some with colored ends
- player picks a pop - wins pop plus prize indicated by colored end (if any)
• Includes 1/8” peg board, 1/8” white tile board
• Does not include hula hoop; purchase either adult or child hula hoop at
local toy store
DLR: $152.60 Ea
TD
#3IAR
3 IN A ROW GAME
Jack's Games
• Tabletop model measures 15” x
15” x18” H
• Game box subdivided into nine
softball-size sections
• Toss three balls into box - any three
in a row wins
• Box has 1/8” clear plexiglass front
for visibility
• Balls included
DLR: $184.25 Ea
RD
DART GAMES
Jack's Games
• Both adult and children's versions of
game available
• Adult game features wooden board
for attaching balloons - includes one
dozen darts and 12 dozen balloons
• Children's game features metallic
board with magnetic darts - player
wins by having dart land inside
pictures of balloons
#JGDB Darts & balloons $263.00 Ea
#JGMD Magnetic darts
315.80 Ea
B
64
Party Products
Non-Food Service
RSS
2014
DISTRIBUTORS
wheels of chance
VOLLEYBALL SET
WHEELS OF CHANCE
RSS
•
•
•
•
•
•
•
•
Deluxe quality wheels of chance available in many different themes and sizes
All wheels superbly balanced around excellent quality bearing
Constructed from highest quality American and Canadian 3/4" birch plywood with steel edge molding
Chrome plated and rubber tipped steel pins extend 2" from wheel surface
Adjustable clicker controls drag, allowing adjustment of spin times
High quality graphics are colorfast
Wheels 42" and smaller (in diameter), include a table stand (plastic base with pole sized to wheel size)
48" wheel includes steel floor stand with steel pole
#WOC-30HR
HORSERACE/
NUMBER
WHEEL
• Diameter: 30"
• Graphic features horses
numbered from 1 to 10
• Doubles as 1-10 number
wheel
DLR: $359.95 Ea RD
#WOC-30MONEY
MONEY WHEEL
• Diameter: 30"
• Graphic features 50 slots
as follows: $1 (22), $2 (14),
$5 (7), $10 (3), $20 (2),
Flag and Joker
DLR: $359.95 Ea RD
#WOC-30DICE
DICE WHEEL
• Diameter: 30"
• Graphic features 50
combinations of 3 die
faces each
#V-BSET
VOLLEYBALL SET
RSS
DLR: $359.95 Ea RD
#WOC-30COLOR
COLOR WHEEL
• Diameter: 30"
• Graphic features six colors
repeated four times
• Adapt wheel to various uses
by assigning prizes to colors
• Dry erase surface coat permits
erasable customizing
DLR:
$359.95 Ea RD
• Wheel of chance pricing is dependent only on the size of the wheel; append the wheel style
(HR, DICE, MONEY OR COLOR) to the part number in the following list to order different size wheels
#WOC-24- - - - -
#WOC-30- - - - -
#WOC-36- - - - -
#WOC-42- - - - -
#WOC-48- - - - -
Wheel of Chance, 24" w/Table Stand
Wheel of Chance, 48" w/Floor Stand
Mikasa
• Durable rubber cover for paved or
grass surface
• Curved, smooth seams
• Deflated for shipping
WHEEL OF CHANCE ACCESSORIES
DLR:
• Layouts are available for all but color wheel themes and provide a convenient means of placing bets
• Single layouts are 13.5" wide by 8' in length and made from naugahyde
• Both table model and floor model bases can be purchased separately
(
$12.20
#C32VB
VOLLEYBALL NET
#WOC-LOHR-NH
Horserace wheel layout, 13.5" x 8', Naughahyde
$29.95 Ea
#WOC-LODICE-NH
Dice wheel layout, 13.5" x 8', Naughahyde
29.95 Ea
#WOC-LOMONEY-NH
Money wheel layout, 13.5" x 8', Naughahyde
29.95 Ea
#WOC-TBLBAS-PLST* Plastic table base only (blue)
22.95 Ea
#WOC-TBLBAS-STL*
Steel table base only (black)
57.00 Ea
#WOC-TBLSTD-30*
Steel base and pole table stand, 30" wheels
97.50 Ea
#WOC-TBLSTD-36*
Steel base and pole table stand, 36" wheels
97.50 Ea
#WOC-FLRSTD
Floor stand only (steel base w/steel pole)
177.50 Ea
*Note: Plastic table base can be used only with wheels originally having a plastic base and steel base only
with wheels originally having steel base. All wheels can be remounted on appropriately sized steel base
and pole.
To Order:
DLR: $178.95
#V2000
VOLLEYBALL
$347.40 Ea
359.95 Ea
389.95 Ea
465.50 Ea
695.80 Ea
DH
• Heavy-duty volleyball set especially
designed for durability in rental
environment
• Net and balls are standard volleyball
products (see below)
• Galvanized fencing poles secured with
tent rope and tent stakes provide extreme
durability in setup materials
• Entire set fits easily into heavy earthtone green 64" canvas bag (included)
• Includes: 1 net, 1 ball,
2 poles, 4 ropes, 4 stakes,
1 carrying bag
NOTE: Always buy extra balls.
J. A. Cissel
• 32' W x 3' H
• Wide tarpaulin headband (2")
w/4mm rope cable
• Twisted polyethylene (2.2mm) square
mesh (4" square)
DLR:
$63.50 Ea
Call: (800) 233-0175
Fax: (717) 892-5981
Web: www.rssd.com
2014 Party Products
Non-Food Service
RSS
DISTRIBUTORS
rabbit COSTUMEs
B
65
costumes
#RUB-S69002
PREMIUM BUNNY SUIT
• Oversized plush-covered latex and
foam head
• Plush white body with pink chest
• Includes mittens, spats and parade
BIG feet (carrot not included)
DLR: $298.00
SANTA CLAUS SUITS
t
en
m
t
r
pa re
De Sto lity
a
Qu
DELUXE VELVETEEN
• Jacket, hat and pants made of spot
and crush resistant upholstery style
cotton-rayon velveteen
• Imitation rabbit fur trim with red
satin lining
• Heavy-duty boot spats
• Heavy-duty belt with 4" buckle
• Elasticized back for tailored fit
• Wig and beard not included
• Sizes: Regular: 42-48
Extra Large: 50-54
#RUB-2353R
Regular
$179.50
#RUB-2353XL Extra Large 207.50
#RUB-1630
EASTER BUNNY SUIT
SUPER DELUXE VELVET
• Finest quality spot and crush-resistant
Lyons velvet
• Other features same as for velveteen suit
above
• Sizes: Extra Large: 50-54
Extra Extra Large: 56+
• White jumpsuit with attached
foot covers
• Soft white fur head with pink ears
• Suit includes white mittens, yellow
polka-dotted vest and bow tie
DLR: $99.50
DLR:
$248.50
#RUB-2354XL Extra Large $248.50
#RUB-2354XXL XX Large
284.00
SANTA WIGS AND BEARDS
MRS SANTA COSTUME
MRS. SANTA DRESS
#RUB-2301
#RUB-2346
• Herculon on
cotton foundation
• 100% kanekalon fiber
• Realistic looking color
• Wash and reset
DLR:
• Long red velvet dress
• Trimmed w/white WildernessTM fur,
sequins and pom-poms
• Includes belt cord and mob cap
• Sizes: Large and medium
#RUB-995L Large
#RUB-995M Medium
TD
$127.00
127.00
$11.25
DLR:
$29.95
OTHER SANTA ACCESSORIES
#RUB-427
Santa Glasses, Square
#RUB-335WNylon Gloves, White
#RUB-26509
Santa Belly (Padding)
#RUB-26502
Santa Bag, 30"x36" Velour (red)
#RUB-26511
Santa Belt, 4" standard
#RUB-26511XL Santa Belt, 4" (XL)
#RUB-22039
Santa Hat
#RUB-2384
Santa Boots
RD
#LAC-002
• Top quality Kanekalon
• Human white color,
slightly silver
• Thick beard and skintopped wig
• Washes easily
DLR:
$71.40
$2.25 Ea
4.90 Pr
14.25 Ea
8.75 Ea
10.50 Ea
13.50 Ea
8.25 Ea
17.25 Pr
B
66
Party Products
Non-Food Service
#BR1
BASIC INFLATOR
West Winds
#BR2HG-75
STANDARD
INFLATOR
#RPB-7-1X
ROYAL AIR DUAL AIR
BALLOON INFLATOR
• Economy rental inflator
• Can be used for latex or Mylar
balloons
• Tilt-valve nozzle, handtight
cylinder connection
• Standard rental inflator
• Can be used for latex or Mylar
balloons
• Tilt-valve nozzle
• Includes large handtight nut, tie
hook, color coded gauge
• Optional ribbon cutter available
DLR:
DLR:
$18.25
DISTRIBUTORS
balloon inflators
West Winds
#BR4HG
DUAL-PURPOSE
INFLATOR
RSS
2014
West Winds
• The most durable electric inflator on the market
• Activated by pushing nozzle
• Pushing down on one nozzle allows the user to
inflate two balloons at once
• Set includes two extension tips for small/twister
balloons and canvas tote bag
DLR: $131.65
$39.35
transfillers
#B4GHT-06
HELIUM/AIR
(60/40)
MIXER
INFLATOR
West Winds
#TR1
PORTABLE HELIUM
TRANSFILLER
West Winds
West Winds
• Always ready for either mylar
or latex inflating
• High-pressure tilt valve for
Latex balloons
• Low-pressure push valve with
needle-tip for Mylar balloons
• Operated by heel of hand
• Includes large handtight nut,
gauge, tie hook and ribbon
cutter
• Latex balloon filler mixes air
with helium supplies
• Ideal for giveaway balloons at
special events
• Save 40% on helium costs
• Inflator features durable brass pushdown valve and includes gauge and
handtight connector
DLR:
DLR: $43.50 Ea
$78.65
• Used to fill small helium tanks from
single supply cylinder, ideal for
filling small rental cylinders
• Handtight cylinder connections
• 36" flexible high-pressure hose
• Safety relief valve and bleeder
valve
• Metering orifice to regulate fill rate
(eliminates safety problems caused
by fully opening large cylinder
valve)
Call for literature and
prices on other more
sophisticated multitank equipment.
DLR: $159.65
CYLINDER TRANSPORT
#HCC2
CYLINDER DOLLY
West Winds
MULTIPLE SUPPLY TRANSFILLERS
West Winds
• Inexpensive transfill assembly
for multiple Supply/Fill cylinders
• Provides maximum efficiency
• Choose from multiple Supply/Fill
options as follows:
•
•
•
•
Steel dolly sized to conveniently transport helium supply cylinders
Back braces matched to cylinder curvature to prevent rolling
Face plate fully supports bottom of cylinder
Safety chain further secures cylinder on cart
DLR:
$153.10 Ea
To Order:
RD
Part#
#TR3D
#TR6
#TR6D
(
Description
DLR
3 Supply, 2 Fill
6 Supply, 1 Fill
6 Supply, 2 Fill
467.65
671.70
753.00
#TR3-1
UPGRADE KIT
• Upgrade TR1 to TR3
DLR: $257.40
Call: (800) 233-0175
Fax: (717) 892-5981
Web: www.rssd.com
2014 Party Products
Non-Food Service
RSS
DISTRIBUTORS
67
safety stands
HELIUM cylinders and systems
ALUMINUM
HELIUM
CYLINDERS
CYLINDER SAFETY
STANDS
West Winds
West Winds
• Lightweight aluminum helium cylinders
• Units include valve, transfill and inflator
fittings (inflator not included)
• Large cylinders (55cf and 125cf) include
-easy carrying handle
• Attractive aluminum casing is
appealing for party rentals
#HCS
• A must for safe operation of
high-pressure tanks
#HCS
• For standard diameter (7"/8") cylinders
• Features quick release band with easy adjusting
knob
Small Diameter (4") Cylinders Fills
apprx.
DLR
#PY-5801-1
8 cf
25-9"
$96.75
#PY-5802-1
14 cf
50-9"
108.95
#PY-5803-1
24 cf
85-9"
117.45
Large Diameter (7"/8") Cylinders
Fills
apprx.
#PY-5807-1
27 cf
100-9"
#PY-5804-1
55 cf 200-9" #PY-5806-1
125 cf 450-9"
B
DLR:
$72.80
#HCS1 (Not pictured)
• For small diameter (4") cylinders
• Molded plastic 9.5" diameter at base x 2.5" high
• Features tightening screws
DLR
142.25
170.45
272.75
DLR: $38.30
balloon accessories
#CYC
CYLINDER
COVERS
#MT
MYLAR TIP
ATTACHMENT
• Black heavy-duty cloth
• Covers large helium supply
cylinders
DLR:
$10.70
#TV
TILT VALVE
• Used as latex inflation
attachment on all West
Winds inflators
DLR:
TD
$5.00
SNAPPI SEAL
LATEX BALLOON
SEALER
• Insert into rubber tilt valve for
inflating mylar balloons
DLR: $5.40
West Winds
#WMG-75
PRESSURE
GAUGE
• Replacement 0-3000 psi color
coded gauge used on all West
Winds inflators and transfillers
• 1/8" male NPT fitting
DLR:
• Eliminates hassle and sore fingers
from tying latex balloons
• Easy and efficient to use - simply
inflate balloon, stretch and twist
neck and slide through sealer
• Single roll of tape will seal
1,000 balloons
• Attach interchangeably to all BR2
(and higher) series inflators
#SS200 Seal unit only
$46.15
#SS102 Seal tape (per roll) 5.40
#BRC Ribbon Cutter $2.45 Ea
#TH1 Tie Hook
2.15 Ea
RIBBON CUTTER/TIE
HOOK
RD
$6.20
BALLOONS
&
BALLOON
ACCESSORIES
See Pages
C5 & C11
B
68
Party Products
Non-Food Service
RSS
2014
CARPET RUNNERS
DISTRIBUTORS
garment steamer
CARPET RUNNERS
#ST400
STEAMBUTLER II
RSS
Econoco
Red Runners
• "Roll Out The Red Carpet" runners
make invited guests feel especially
welcome
• Real carpet runners with all edges
bound
• Lightweight for ease of handling
• Available in three sizes as follows
• Removes wrinkles from clothing, draperies,
tablecovers, etc
• Produces steady high-thrust flow of steam
within 30 seconds
• Durable enough for daily in-store use
• Shatterproof, 2.6 liter easy view water bottle simply fill and use
• Lighted on/off switch
• Auto safety shutoff
• Long hose (66") w/comfort-grip handle
• Easy roll casters
• Solid brass fittings and heating element
• Electrical: 120V, 1350W
• One year limited warranty
#RCR-3X25 Red carpet runner, 3' x 25' $186.90
#RCR-3X50 Red carpet runner, 3' x 50' 373.80
#RCR-4X25 Red carpet runner, 4' x 25' 232.30
White Runner
• Bright white velvet carpet runner suitable for
use at weddings and other appropriate functions
• Lightweight, all edges bound
• Available in single size
DLR: $119.90
#WCR-3X25White Carpet Runner, 3' x 25' $186.90
coat racks
#01-013CH
#RCS-1
COAT RACK,
SINGLE RAIL
COLLASIBLE
#RCS-3
COAT RACK,
DOUBLE RAIL
COLLAPSIBLE
COAT RACK ACCESSORIES
RSS
RSS
• Portable, folding: No nuts,
bolts or tools required
• 48" hangrail, with two 12" pull
out rods
• 55" to 65" adjustable height
• 1" polished chrome-plated
round tubing
• 4" ball bearing casters
• Holds up to 60 garments
• Same concept as time-tested
RCS-1 rack
• Double 48" hangrails w/12" pullout rods on all four ends
• Height adjustable from 54" to
64"
• Top rail separation: 21"
• Round satin chrome tubing, 1"
• Ball bearing casters, 4"
DLR:
DLR: $102.80 Ea
To Order:
RSS
#01-008CH
RSS
$59.20 Ea
#ZRACK-III
COAT RACK, Z-FRAME
PORTABLE
• Screen fits both RCS-1 and RCS-3
racks and can be used as a lower shelf on the RCS-1 rack only
• Top basket (22" x 54") clamps onto RCS-3 rack only to provide space
for hats, etc.
• Top basket folds for storage and
transport of rack
#01-013CH Screen/ $24.80 Ea
Lower Shelf
#01-008CH Top Basket
37.20 Ea
(
• Z-frame design of rack allows
tight nesting for storage - no
need to collapse and stack
• Adjustable height lower cross bar
accommodates second row of
short items
• 1.5" square tubing base
• 1.25" round tubing side and cross
bars
• Length: 62"
• Height: 70"
• 4" industrial casters
• Sold by each
DLR:
$77.30 Ea
Call: (800) 233-0175
Fax: (717) 892-5981
Web: www.rssd.com
2014 Party Products
Non-Food Service
RSS
DISTRIBUTORS
mattress covers
B
69
wedding umbrella
#WEDUM6
WEDDING UMBRELLA
RSS
MATTRESS COVERS
Postcraft
• Hospital quality mattress covers
• Prem-aclave® premium vinyl
formulation offers long-lasting
institutional strength
• Generously cut and zippered
for easier, longer-lasting fit
• Remains comfortable soft and
pliable, even after countless
washings
• Electronically welded seams
• Wipe clean with damp cloth or
machine wash and dry
• Waterproof and stain resistant
• Flame retardant
• Guaranteed against defects in
material and workmanship
Part#
Cover Size
DLR.
Closeout While
Supplies Last
FOR ROLLAWAY BEDS
#PR-30724Z
#PR-30726Z
#PR-39724Z
#PR-39726Z
#PR-48724Z
#PR-48726Z
30"X72"X4""
30"X72"X6""
39"X72"X4"
39"X72"X6"
48"X72"X4"
48"X72"X6"
$20.40
23.25
24.30
27.00
31.75
33.90
• Protect bride (and groom) from rain or sun with umbrella
compatible with other wedding decor
• Approximately six feet in diameter when open
• Each of the eight ribs is 36" long
• Fabric is waterproof and water repellant
• Ruffle helps keep water from rolling off edge of umbrella
• Sold each and 12 per case
FOR CRIBS Closeout
#PR-29524Z
#PR-25393Z
29"X52"X4"
25"X39"X3"
$24.95
24.95
DLR: $19.00 Ea
scissors
BEDDING DISINFECTANT
STERI-FAB® DISINFECTANT
Noble Pine Products
CEREMONIAL
SCISSORS
RSS
#SF-12P2
#SF-4G2
#PTS
#CAS
• Much more than a disinfectant, Steri-Fab also is an insecticide, a
bactericide, a fungicide, a deodorant, a germicide, a viricide, a
mildewicide and a sanitizer
• For use on mattresses, bedding, furniture, carpet, etc.
• Requires no dilution - simply spray on and allow to dry (about 15 minutes)
• Non-staining and non-residual (no chemical residue)
• Available in pint and gallon containers
Steri-Fab MSDS
• Coverage: 1500 sq. ft. per gallon
available at
www.rssd.com
• Plastic trigger sprayers attach to one-gallon
containers to permit direct spraying from these containers
• Continuous action sprayer has one quart capacity, is
fully labeled for use with Steri-fab, and dispenses at the
recommended coverage rate
Meets All
®
Description
Qty
DLR
Case
#SF-12P
Pints w/sprayer 12
$127.90 Cs
#SF-4G
Gallons
4
46.90 Ea
163.00 Cs
#PTS
Plastic Trigger Sprayers
5.95 Ea
#CAS
Continuous Action Sprayer
27.30 Ea
TD
State
Requirements
For
Bedding
Disinfection
These cut just
like real scissors
•
•
•
•
•
•
Quality scissors in a ceremonial size
All steel construction
Black, enameled, molded handles
Dimensions: 25" x 8" x 2"
Weight: 3 lbs.
Available in gold-plated as well as standard steel shears
RD
#06225
Steel shears $150.00
#06225-GP Gold-plated 230.00
shears
RD

Section B - RSS Distributors

Transcription

Similar documents

The Jülich Solar Power Tower

31. Tage der raumfahrt 11.-15. November 2015

subscribe to RSS feed contact us project updates

IAA-B10-0802

PRECIOS INGLES DOLARES CONFITEXPO 2015 MARCH

Spatial Resolution Assessment from Real Image Data

Balneario Cupones Ing - Balneario de Archena

Description of US Trial Site

1-888-EDS-ROTO (337-7686)

German EO missions: TerraSAR-X, TanDEM