1 SPK 100 Series 1-15

Transcription

Dampers
Dampers
SPK Series
Volume Control Damper
General
(Flange Type)
SPK 30 - 100
Standard Construction
FRAME:
180mm x 30mm x 1.5mm (16 ga.) galvanized steel formed
channel for flange connections.
2
2
BLADES:
250mm max. width, 1.5mm (16 ga.) galvanized steel.
Silencers
FINISH:
Mill galvanized.
LINKAGE:
Acoustic
Enclosures
Side linkage concealed in frame for parallel and opposed
blade operation.
Face linkage available (optional).
CASE BEARINGS:
Plenum
Boxes
Brass bearing as standard.
Sintered bronze oilite (optional).
AXLES:
12mm diameter zinc plated mild steel.
Louvers
CONTROL SHAFT:
MINIMUM SIZE:
Kitchen
Hoods
100 x 100mm, damper up to 250mm high are single blade
construction.
MAXIMUM SIZE:
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
1200 x 1800mm, as single section.
Multiple section assembly with unlimited size, where each
section operates independently.
For details of multiple sections consult SAFID.
TEMPERATURE LIMITS:
Description
-40 ˚C to + 100 ˚C.
Single and multi-leaf volume control dampers are designed
for quiet, efficient and reliable air volume control in ventilation
systems.
The SPK30 Damper is ruggedly built damper, with a case
of robust assembly formed from channel frame for flanged
connections to ductwork. The blades are formed single skin
reinforced, with longitudinal structurally designed vee.
Blade action is standard as parallel but can be supplied as
opposed blade action at no addtional charge.
Blade edge seals and jamb (side) seals can be fitted for
low leakage requirements. Dampers can be manual with
locking quadrant or motorized with a wide range of electrical
actuators readily available.
SPK 30 - 110
General construction as type SPK30-100 damper but
blades, shafts and blade to shaft fixing in stainless steel
(Grade 304).
SPK 30 - 120
General construction as type SPK30-100 damper but with
frame, blades shafts and blade to shaft fixing and linkage
all from stainless steel (Grade 304).
Right to alterations reserved.
is a registered trade mark.
© copyright SAFID 2004 - All Rights Reserved
Dampers
SPK Series
Dimensions
1 - Casing
2 - Drive Shaft
3 - Side Linkage
4 - Blade
5 - Landing Angles
6 - Bearing
Flange Type
SPK30 - 100…110…120
SPK30 - 100…110…120
Flange Type, Parallel/Opposed Blade
Standard Sizes
2
3
Supports
& Bands
Access
Doors
Flexible
Connectors
Number of Blades
1
1
1
1
2
2
2
2
3
3
4
5
5
6
7
7
8
9
9
10
11
12
Flanges &
Accessories
Opposed
Blade (OB)
H in mm
100
150
200
250
300
350
400
450
500
600
700
800
900
1000
1100
1200
1300
1400
1500
1600
1700
1800
Tapes &
Sealants
Parallel
Blade (PB)
W in mm
100
150
200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
1000
1050
1100
1200
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
Flange Type
General
(Flange Type)
Dampers
SPK Series
General
(Sleeve Type)
SPK 40 - 100
FRAME:
100mm x 40mm x 1.5mm (16 ga.) galvanized steel,
structurally designed hat section.
2
4
BLADES:
Silencers
FINISH:
Mill galvanized.
LINKAGE:
Acoustic
Enclosures
Face linkage parallel blade operation.
CASE BEARINGS:
Plenum
Boxes
AXLES:
CONTROL SHAFT:
Louvers
12mm diameter zinc plated mild steel. (Removable for
sleeve shaft).
MINIMUM SIZE:
Kitchen
Hoods
construction.
MAXIMUM SIZE:
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
TEMPERATURE LIMITS:
-40 ˚C to + 100 ˚C.
Description
systems.
The SPK40 Damper is ruggedly built damper, with a case
of robust structurally designed hat section to slide in ducting
for duct connection. The blades are formed single skin
reinforced, with longitudinal structurally designed vee.
SPK 40 - 110
(Grade 304).
SPK 40 - 120
Dampers
SPK Series
Dimensions
1 - Casing
2 - Drive Shaft/Removable Spindle (when required)
3 - Bar Linkage
4 - Blade
5 - Landing Angles
6 - Bearing
Sleeve Type
SPK40 - 100…110…120
SPK40 - 100…110…120
Sleeve Type, Parallel Blades
Standard Sizes
2
5
Supports
& Bands
Access
Doors
Flexible
Connectors
Number of Blades
1
1
1
1
1
2
2
2
2
3
4
4
5
6
6
7
8
8
9
10
11
12
Flanges &
Accessories
H in mm
100
150
200
250
300
350
400
450
500
600
700
800
900
1000
1100
1200
1300
1400
1500
1600
1700
1800
Tapes &
Sealants
Parallel Blade (PB)
W in mm
100
150
200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
1000
1050
1100
1200
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
Sleeve Type
General
(Sleeve Type)
Dampers
SPK Series
General
(Circular Spigot Type)
SPK 50 - 100
FRAME:
180mm x 1.5mm (16 ga.) galvanized steel, spigot type
380mm wide with circular spigot duct connection.
2
6
BLADES:
Silencers
FINISH:
Mill galvanized.
LINKAGE:
Acoustic
Enclosures
blade operation.
CASE BEARINGS:
Plenum
Boxes
AXLES:
Louvers
CONTROL SHAFT:
MINIMUM SIZE:
Kitchen
Hoods
construction.
MAXIMUM SIZE:
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
TEMPERATURE LIMITS:
Description
-40 ˚C to + 100 ˚C.
systems.
The SPK50 Damper is ruggedly built damper, with a spigot
case of robust assembly formed circular spigot connection
to ductworks. The blades are formed single skin reinforced,
with longitudinal structurally designed vee.
SPK 50 - 110
(Grade 304).
SPK 50 - 120
Dampers
SPK Series
Dimensions
1 - Casing
3 - Side Linkage
4 - Blade
5 - Landing Angles
6 - Bearing
Circular Spigot Type
SPK50 - 100…110…120
SPK50 - 100…110…120
Circular Spigot Type, Parallel/Opposed Blades
Standard Sizes
2
7
Supports
& Bands
Access
Doors
Flexible
Connectors
Number of Blades
1
1
1
1
2
2
2
3
3
4
4
5
6
6
7
7
Flanges &
Accessories
Opposed
Blade (OB)
H in mm
100
150
200
250
300
350
400
450
500
600
700
800
900
1000
1100
1150
Tapes &
Sealants
Parallel
Blade (PB)
W in mm
100
150
200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
1000
1050
1100
1200
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
General
Dampers
SPK Series
General
(Oval Spigot Type)
SPK 60 - 100
FRAME:
380mm wide with oval spigot duct connection.
2
8
BLADES:
Silencers
FINISH:
Mill galvanized.
LINKAGE:
Acoustic
Enclosures
blade operation.
CASE BEARINGS:
Plenum
Boxes
AXLES:
Louvers
CONTROL SHAFT:
MINIMUM SIZE:
Kitchen
Hoods
construction.
MAXIMUM SIZE:
Supports
& Bands
TEMPERATURE LIMITS:
-40 ˚C to + 100 ˚C.
The SPK60 Damper is ruggedly built damper, with a spigot
case of robust assembly formed oval spigot connection to
ductworks. The blades are formed single skin reinforced,
with longitudinal structurally designed vee.
Tapes &
Sealants
Flexible
Connectors
systems.
Flanges &
Accessories
Access
Doors
Description
SPK 60 - 110
(Grade 304).
SPK 60 - 120
Dampers
SPK Series
Dimensions
1 - Casing
2 - Drive Shaft
3 - Side Linkage
4 - Blade
5 - Landing Angles
6 - Bearing
Oval Spigot Type
SPK60 - 100…110…120
SPK60 - 100…110…120
Standard Sizes
2
9
Supports
& Bands
Access
Doors
Flexible
Connectors
Number of Blades
1
1
1
1
2
2
2
3
3
4
4
5
6
6
7
7
Flanges &
Accessories
Opposed
Blade (OB)
H in mm
100
150
200
250
300
350
400
450
500
600
700
800
900
1000
1100
1150
Tapes &
Sealants
Parallel
Blade (PB)
W in mm
100
150
200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
1000
1050
1100
1150
1200
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
Oval Spigot Type
General
(Oval Spigot Type)
Dampers
SPK Series
General
Removable Spindle
Mounting Bracket
For Sleeve type only
Damper with Mounting Bracket for actuator.
Mounting Bracket or anti-rotation strap to be
supplied with motorized damper.
Blade Seal
Type S1
Side Seal (Jamb Seal)
Type S2 (Stainless Steel type 304)
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
10
Materials - Construction
Note:
Type S3 (Combination of S1 & S2)
Dampers
Installation Details
Flange Type SPK30
Damper to Slide on Flange Connection
Flange Type SPK30
Damper to angle Flange Connection
General
SPK Series
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
11
Supports
& Bands
No. of Holes No. of Holes
W Dim.
H Dim.
1
2
2
2
2
2
2
3
3
3
3
4
4
4
4
4
4
5
5
6
6
6
7
7
8
8
8
9
9
10
10
10
11
12
13
14
14
15
Access
Doors
H
in mm
100
150
200
250
300
350
400
450
500
600
700
800
900
1000
1100
1200
1300
1400
1500
1600
1700
1800
Flexible
Connectors
W
in mm
100
150
200
250
300
350
400
450
500
600
700
800
900
1000
1100
1200
Flanges &
Accessories
Flange Drilling Details
Tapes &
Sealants
Flange Drilling Details, Type SPK30 only
Kitchen
Hoods
Dampers
SPK Series
General
Sleeve type SPK40
Circular type SPK50 & Oval type SPK60
Technical Data
Pressure Loss
Vf
A
Pt
in Pa
in m/s
in m2
= Total Pressure Drop.
= Face Velocity based on A.
= Damper cross-sectional area.
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
12
= Blade angle, when
= 0˚, blades are fully open.
Dampers
SPK Series
General
Belimo Actuators
S2
S3
Side seals. Fitted to close gap
between frame and blades.
Combination of side seals & blade
seals to close gap between frame
and blades and blade seals to
seal blade to blade joint for ultra
low leakage characteristic.
Linkage
Description
PB
Side linkage concealed in frame for
parallel blade operation.
Face linkage available (optional)
OB
External side linkage for opposed
blade operation.
BF24 spring return
A03
AF230 spring return
A04
AF230-S spring return with limit switch
A05
AF230 US spring return
A06
A07
AF230-S US spring return with limit switch
A08
A09
A10
A11
AF24-SR spring return
A12
NF24 US spring return
A13
A14
NF24-S US spring return with limit switch
A15
A16
NF24-SR US Modulating
A17
SM230A open/closed
A18
SM24A open/closed
A19
SM230A-SR Modulating
A20
NM230 open/closed
A21
NM24 open/closed
A22
NM24 SR Modulating
A23
GM240 open/closed
A24
GM24 open/closed
A25
GM24-SR Modulating
Other Belimo Actuators models and voltages are
available, For inquiry contact SAFID.
Flexible
Connectors
Construction
Variants
A02
Bearings
Flanges &
Accessories
B
Description
Brass (Standard Supply)
B1
Construction sintered bronze
oilite.
B2
Stainless steel
Tapes &
Sealants
Construction
Variants
2
13
Silencers
Blade edge seal to seal blade
to blade joint for low leakage
characteristic.
BF230 spring return
Acoustic
Enclosures
S1
A01
Plenum
Boxes
S
Standard supply construction. No
side seals or blade seals.
Type / Model
Louvers
Description
Kitchen
Hoods
Code
Construction
Variants
Supports
& Bands
Seals
Access
Doors
Product Range
Dampers
SPK Series
General
Order Code
SPK30-100-PB-S-B-R
Variants - Case
*SPK30 = Flange
(Standard Supply)
SPK40 = Sleeve
SPK50 = Circular Spigot
SPK60 = Oval Spigot
Type
*100 (Standard Supply)
110
120
Variants - Blade Operation
*PB
= Side linkage Parallel
(Standard Supply)
OB
= Opposed blade
/
500 x 500
/
A 17
Duct Size
Square or rectangular
Dimensions 'W' x 'H' mm
Circular 'D' mm dia.
Flat oval 'B' x 'D' mm.
All damper spigots are
manufactured down on duct
size to fit inside ductwork
connections.
Actuators
(See page 13)
External Controls
*"R"
= Right hand (Standard Supply)
"L"
= Left hand
Variants - Bearings
*B
= Brass (Standard Supply)
B1
= Sintered bronze (oilite)
B2
= Stainless Steel
Variants - Seals
*S
= None (Standard Supply)
S1
= Blade seals only
S2
= Side seal (jamb)
S3
= Side seal & blade seals
* Stands for Standard Supply.
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
14
Order Details
Dampers
SPK Series
STANDARD
.
.
.
2
15
Silencers
Make : SAFID
Type : SPK 30 - 100 PB - S - B - R / 500 x 500
Qty : 1
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Kitchen
Hoods
Louvers
Plenum
Boxes
Volume control dampers designed for volume flow and
pressure control or to isolate sections of ducting in
ventilation systems, shall be of the SPK series as specified.
Damper casing shall be constructed of Ga. 16 galvanized
steel.
Blades shall be single skin reinforced constructed of Ga.
16 galvanized steel (optional with blade seals and/or side
seals).
Shafts to be 12mm mild plated steel with brass or sintered
bronze bearings (optional).
Blades to be connected by side or face linkage.
Parallel or opposed blade operation dampers; with manual
or motorized operation. Limit switches and closed blade low
leakage constructions are optional readily available.
General
Order Example
Acoustic
Enclosures
Specification Text
Dampers
SPK Series
Airfoil Blades
General
(Flange Type)
SPK 30 - 200
FRAME:
180mm x 30mm x 1.5mm (16 ga.) galvanized steel.
Formed channel for flange connections.
2
16
BLADES:
Silencers
Airfoil shaped galvanized steel double skin construction,
16 gauge equivalent thickness, 250mm max. width.
FINISH:
Mill galvanized.
LINKAGE:
Acoustic
Enclosures
blade operation.
CASE BEARINGS:
Plenum
Boxes
AXLES and CONTROL SHAFT:
Louvers
MINIMUM SIZE:
construction.
MAXIMUM SIZE:
Kitchen
Hoods
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Description
SPK 30 - 210
systems.
The SPK -200 Damper is ruggedly built damper, with a
casing of robust assembly formed from channel frame for
flanged connections to ductwork. The blades are formed of
double skin airfoil providing lower pressure drop in the open
position for smooth airflow with reduced turbulance.
Blade seals and jamb (side ) seals can be fitted for low
leakage requirements. Dampers can be manual with
(Grade 304).
SPK 30 - 220
Dampers
(Flange Type)
Dimensions
1 - Casing
2 - Drive Shaft
3 - Side Linkage
4 - Blade
5 - Landing Angles
6 - Bearing
Flange Type
SPK30 - 200…210…220
SPK30 - 200…210…220
Flange Type, Parallel/Opposed Blades
Standard Sizes
2
17
Supports
& Bands
Access
Doors
Flexible
Connectors
Number of Blades
1
1
1
2
3
4
5
6
7
8
9
10
11
12
Flanges &
Accessories
Opposed
Blade (OB)
H in mm
150
200
250
300
450
600
750
900
1050
1200
1350
1500
1650
1800
Tapes &
Sealants
Parallel
Blade (PB)
W in mm
150
200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
1000
1050
1100
1150
1200
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
Flange Type
General
SPK Series
Airfoil Blades
Dampers
SPK Series
Airfoil Blades
General
(Sleeve Type)
SPK 40 - 200
FRAME:
2
18
BLADES:
Silencers
Airfoil shaped galvanized steel double skin construction,
16 gauge equivalent thickness, 300mm max. width.
FINISH:
Mill galvanized.
LINKAGE:
Acoustic
Enclosures
Side linkage for opposed or parallel blade available
operation.
CASE BEARINGS:
Plenum
Boxes
Louvers
MINIMUM SIZE:
construction.
MAXIMUM SIZE:
Kitchen
Hoods
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Description
SPK 40 - 210
systems.
(Grade 304).
casing of robust assembly formed top hat sleeve to slide
in ductwork. The blades are formed of double skin airfoil
providing lower pressure drop in the open position for
smooth airflow with reduced turbulance.
SPK 40 - 220
Dampers
(Sleeve Type)
Dimensions
1 - Casing
2 - Drive Shaft
3 - Side Linkage
4 - Blade
5 - Landing Angles
6 - Bearing
Sleeve Type
SPK40 - 200…210…220
SPK40 - 200…210…220
Standard Sizes
2
19
Opposed
Blade (OB)
Supports
& Bands
Access
Doors
Flexible
Connectors
Number of Blades
1
1
1
2
3
4
5
6
7
8
9
10
11
12
Flanges &
Accessories
H in mm
150
200
300
350
450
600
750
900
1050
1200
1350
1500
1650
1800
Tapes &
Sealants
Parallel
Blade (PB)
W in mm
150
200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
1000
1050
1100
1150
1200
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
Sleeve Type
General
SPK Series
Airfoil Blades
Dampers
SPK Series
Airfoil Blades
General
SPK 50 - 200
FRAME (Spigot type)
2
20
BLADES:
Silencers
Airfoil shaped galvanized steel double skin construction, 16
gauge equivalent thickness, 250mm max. width.
FINISH:
Mill galvanized.
LINKAGE:
Acoustic
Enclosures
blade operation.
CASE BEARINGS:
Plenum
Boxes
Louvers
MINIMUM SIZE:
construction.
MAXIMUM SIZE:
Kitchen
Hoods
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Description
SPK 50 - 210
for quiet, efficient and reliable air volume control in
ventilation systems.
(Grade 304).
SPK 50 - 220
Dampers
Dimensions
1 - Casing
2 - Drive Shaft
3 - Side Linkage
4 - Blade
5 - Landing Angles
6 - Bearing
SPK50 - 200…210…220
SPK50 - 200…210…220
Standard Sizes
2
21
Supports
& Bands
Access
Doors
Flexible
Connectors
Number of Blades
1
1
1
2
3
4
5
6
7
8
9
10
11
12
Flanges &
Accessories
Opposed
Blade (OB)
H in mm
150
200
250
300
450
600
750
900
1050
1200
1350
1500
1650
1800
Tapes &
Sealants
Parallel
Blade (PB)
W in mm
150
200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
1000
1050
1100
1150
1200
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
General
SPK Series
Airfoil Blades
Dampers
SPK Series
Airfoil Blades
General
(Oval Spigot Type)
SPK 60 - 200
FRAME (Spigot type)
380mm wide with ova spigot duct connection.
2
22
BLADES:
Silencers
Airfoil shaped galvanized steel double skin construction, 16
gauge equivalent thickness, 250mm max. width.
FINISH:
Mill galvanized.
LINKAGE:
Acoustic
Enclosures
blade operation.
CASE BEARINGS:
Plenum
Boxes
Louvers
MINIMUM SIZE:
construction.
MAXIMUM SIZE:
Kitchen
Hoods
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Description
SPK 60 - 210
systems.
(Grade 304).
SPK 60 - 220
Dampers
(Oval Spigot Type)
Dimensions
1 - Casing
2 - Drive Shaft
3 - Side Linkage
4 - Blade
5 - Landing Angles
6 - Bearing
Oval Spigot Type
SPK60 - 200…210…220
SPK60 - 200…210…220
Oval Spigot Type, Parallel/Opposed Blades
Standard Sizes
2
23
Supports
& Bands
Access
Doors
Flexible
Connectors
Number of Blades
1
1
1
2
3
4
5
6
7
8
9
10
11
12
Flanges &
Accessories
Opposed
Blade (OB)
H in mm
150
200
250
300
450
600
750
900
1050
1200
1350
1500
1650
1800
Tapes &
Sealants
Parallel
Blade (PB)
W in mm
150
200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
1000
1050
1100
1150
1200
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
Oval Spigot Type
General
SPK Series
Airfoil Blades
Dampers
SPK Series
Airfoil Blades
General
Removable Spindle
Mounting Bracket
Sleeve type SPK40
Damper with mounting bracket for actuator
Mounting bracket or anti-rotation strap to be
supplied with motorized damper.
Blade Seal
Type S1
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
24
Note:
Dampers
SPK Series
Airfoil Blades
General
Flange type SPK30
Damper to angle Flange Connection
2
25
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
Flange type SPK30
Damper to slide on Flange Connection
No. of Holes
H Dim.
2
2
2
3
3
4
4
4
5
6
6
7
8
9
10
10
11
12
13
14
14
15
Supports
& Bands
No. of Holes
W Dim.
1
2
2
2
3
3
4
4
4
5
6
7
8
8
9
10
Access
Doors
H
in mm
100
150
200
250
300
350
400
450
500
600
700
800
900
1000
1100
1200
1300
1400
1500
1600
1700
1800
Flexible
Connectors
W
in mm
100
150
200
250
300
350
400
450
500
600
700
800
900
1000
1100
1200
Flanges &
Accessories
Tapes &
Sealants
Flange Drilling Details, type SPK30 only
Kitchen
Hoods
Dampers
SPK Series
Airfoil Blades
General
Sleeve type SPK40
Circular type SPK 50 & Oval type SPK 60
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
26
Technical Data
Pt
Vf
A
in Pa = Total Pressure Drop.
in m/s = Face Velocity based on A.
in m2 = Damper cross-sectional area.
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Pressure Loss
= Blade angle, when
= 0˚, blades are fully open.
Dampers
S2
S3
A01
BF230 spring return
A02
BF24 spring return
A03
AF230 spring return
A04
Blade edge seal to seal blade
to blade joint for low leakage
characteristic.
Combination of side seal & blade
seals to close gap between frame
and blades and blade seals to
seal blade to blade joint for ultra
Linkage
Construction
Variants
Description
PB
Face linkage available (optional)
External side linkage for opposed
blade operation.
A06
A07
A08
A09
A10
A11
A12
A13
A14
A15
A16
A17
SM230A open/closed
A18
SM24A open/closed
A19
A20
NM230 open/closed
A21
NM24 open/closed
A22
NM24 SR Modulating
A23
GM240 open/closed
A24
GM24 open/closed
A25
GM24-SR Modulating
For Belimo Actuators details, models and voltages
see pages 126 - 143 or contact SAFID.
Flexible
Connectors
OB
A05
Bearings
Flanges &
Accessories
B
Description
Brass (Standard Supply)
B1
oilite.
B2
Stainless steel
Tapes &
Sealants
Construction
Variants
2
27
Silencers
Standard supply construction. No
side seals or blade seals.
Type / Model
Acoustic
Enclosures
S1
Code
Plenum
Boxes
S
Description
Louvers
Construction
Variants
Kitchen
Hoods
Seals
Supports
& Bands
Belimo Actuators
Access
Doors
Product Range
General
SPK Series
Airfoil Blades
Dampers
SPK Series
Airfoil Blades
General
Order Details
Order Code
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
28
SPK30-200-PB-S-B-R
Variants - Case
Frame Type
*SPK30 = Flange
(Standard Supply)
SPK40 = Sleeve
SPK50 = Circular type
SPK60 = Oval type
/
500 x 500
/
Duct Size
A 17
Actuators
(see page 27)
Flat oval 'B' x 'D' mm.
All damper spigots are manufactured
down on duct size to fit inside
ductwork connections
External Controls
Type
*200 (Std Supply)
210
220
* "R"
"L"
= Left hand
Variants - Bearings
*B
B1
B2
= Brass (Standard Supply)
= Sintered bronze oilite (optional)
= Stainless Steel
* PB = Side Linkage Parallel
(Standard Supply)
OB
Opposed blade
Supports
& Bands
Kitchen
Hoods
Variants - Seals
*S
S1
S2
S3
= No seals (Standard Supply)
= Blade Seal only (175 ˚C)
= Side seal (jamb)
= Side & blade seal (175˚C)
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
* - Stands for Standard Supply.
Dampers
SPK Series
Airfoil Blades
Airfoil blades Volume control dampers designed for volume
flow and pressure control or to isolate sections of ducting
in ventilation systems, shall be of the SPK 200 series as
specified.
Damper casing shall be constructed of Ga. 16 galvanized
steel. Blades shall be double skin (airfoil section blades of
Ga. 22 galvanized steel (optional) with blade seals and/or
side seals).
Shafts to be 12mm mild plated steel with brass or sintered
bronze bearings. Blades to be connected by face or external
linkage.
General
Order Example
STANDARD
Make : SAFID
Type : SPK 30 - 200 - PB - S - B - R / 500 x 500
Qty : 1
.
.
.
2
29
Silencers
Specification Text
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Parallel or opposed blade operation dampers; with manual
or motorized operation. Limit switches and closed blade low
leakage constructions are optional readily available.
Dampers
General
Round Volume Control Damper
SP 500
SP Series
BODY:
Galvanized steel sheet.
Gauge 20 : from Dia. 80mm to 500mm.
Gauge 18 : above 500 Dia.
2
30
BLADE:
Silencers
Plain galvanized steel sheet.
Gauge 18: from Dia. 80mm to 500mm.
Gauge 16: above 500 Dia.
Galvanized steel perforated blade (optional)
Acoustic
Enclosures
Mill galvanized.
Plenum
Boxes
FINISH:
CONTROL SHAFT:
CASE BEARINGS:
MINIMUM & MAXIMUM SIZE:
Louvers
80mm Dia. damper up to 610 Dia. are single blade
construction.
Description
SP 510
Casing & blades made from galvanized steel sheet.
Adjustable damper blade mounted on brass bushes with
manually operated quadrant and position indicator. The
damper is used for regulating air flow or as shutt-off damper
when complete sealing against air flow is not required.
General construction as type SP500 damper but blades,
shafts and blade to shaft fixing in stainless steel (Grade
304).
Dampers can be manual with locking quadrant or
motorized with a wide range of electrical actuators readily
available.
SP 520
General construction as type SP500 damper but with frame,
blades shafts and blade to shaft fixing all from stainless
steel (Grade 304).
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Kitchen
Hoods
Note:
Sizes above 610 Dia. are multiblade type.
Dampers
SP Series
1 - Casing
3 - Drive Shaft
Mounting Bracket
Damper with mounting bracket & motor
2
31
305
100
315
125
350
140
400
150
450
160
500
180
550
200
600
224
610
250
280
The end joints are also available
with factory applied self sealing gaskets.
Supports
& Bands
80
Access
Doors
Dia
mm
Flexible
Connectors
Dia
mm
Flanges &
Accessories
Standard Sizes
Tapes &
Sealants
Section Details
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
SP 500…510…520
2 - Blade
General
Dimensions
Dampers
General
Round Shut-off Damper
SP Series
SP 600
BODY:
Gauge 20 : from Dia. 80mm to 500mm.
Gauge 18 : above 500 Dia.
2
32
BLADE:
Silencers
Gauge 14 (2mm thk) : 2 layers gauge 20 plain galvanized
steel bolted together equivalent to gauge 14 with full
circumference.
FINISH:
Acoustic
Enclosures
Mill galvanized.
CASE BEARINGS:
Plenum
Boxes
CONTROL SHAFT:
Louvers
construction.
Description
SP 610
Adjustable damper blade mounted on brass bushes and
blades with rubber seal, when complete sealing of air flow
is required.
304).
Dampers can be manual with locking quadrant and position
indicator or motorized with a wide range of electrical
SP 620
steel (Grade 304).
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Kitchen
Hoods
Note:
Dampers
SP Series
1 - Casing
3 - Drive Shaft
2 - Blade
4 - Rubber Seal
Mounting Bracket
2
33
305
315
125
350
140
400
150
450
160
500
180
550
200
600
224
610
250
280
Supports
& Bands
80
100
Access
Doors
Dia
mm
Flexible
Connectors
Dia
mm
Flanges &
Accessories
Standard Sizes
Tapes &
Sealants
Section Details
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
SP 600…610…620
General
Dimensions
Dampers
General
SP Series
SP 700
BODY:
2
34
BLADE:
Plain galvanized steel sheet gauge 10 (3.5mm thk)
FINISH:
Silencers
Mill galvanized.
CASE BEARINGS:
Acoustic
Enclosures
CONTROL SHAFT:
Plenum
Boxes
construction.
Description
SP 710
Casing & blades made from heavy galvanized steel sheet.
Adjustable damper blade mounted on brass bushes with
manually operated quadrant damper. The movement of
the blade permits regulation from fully open to almost
complete shut off.
304).
OPTION:
DAMPER WITH AIRTIGHT BLADE:
Stopper end for airtight blade, code AT.
Dampers can be manual with locking quadrant and position
indicator or motorized with a wide range of electrical
SP 720
steel (Grade 304).
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Kitchen
Hoods
Louvers
Note:
Dampers
SP Series
1 - Casing
3 - Drive Shaft
2 - Blade
4 - Stopper ends for airtight blade
Mounting Bracket
2
35
315
125
350
140
400
150
450
160
500
180
550
200
600
224
610
250
280
Supports
& Bands
100
Access
Doors
Dia
mm
305
Flexible
Connectors
Dia
mm
80
Flanges &
Accessories
Standard Sizes
Tapes &
Sealants
Section Details
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
SP 700…710…720
General
Dimensions
Dampers
General
SP Series
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
36
Dampers
General
Order
Order example:
Product code:
SP500
-
aaa
Type
SP500
2
37
Diameter
For Motorized Dampers:
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Kitchen
Hoods
Louvers
Plenum
Boxes
Wide range of electrical actuators are readily available,
Acoustic
Enclosures
SP700
Silencers
SP600
Tapes &
Sealants
Pressure Loss
SP Series
Dampers
Pressure Relief Damper
PRD Series
General
(Wall Mounted)
PRD 50 - 100
Description
Pressure Relief Dampers, are used in intake & discharge
openings in commercial and residential airconditioning
systems. When the ventilation system is on, the blades
of the pressure relief damper are held in the open position
by the air flow. If the system is switched off, the damper
blades close automatically, thus preventing reverse airflow
and giving protection against the ingress of untempered
air, rain and birds into the airconditioning system.
Supports
& Bands
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
38
PRD 50 - 110
FRAME:
General construction as type PRD 50-100 damper but
frame & blades, all from mill finish aluminum sheets.
Gauge 18 ga. (1.2mm thk.) from formed galvanized steel
sheet.
BLADES:
100mm max. width, 0.75mm thk. mill finish aluminum
sheet.
Sealing strip on blades in foam gasket.
LINKAGE:
Galvanized steel sheet 28mm x 22 gauge
PRD 50 - 120
BEARINGS:
General construction as type PRD 50-100 damper but frame
& blades, all from galvanized steel sheets construction
with counter weight.
Bearing section in plastic 6mm.
Blade stub shafts in brass.
MINIMUM SIZE:
construction.
MAXIMUM SIZE:
PRD 50 - 130
General construction as type PRD 50-100 damper but with
frame built of stainless steel sheet type 304, 2B finish and
blades built of mill finish aluminum sheets.
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
SHAFTS:
Dampers
PRD Series
Construction - Dimensions
1 - Casing
2 - Blade
3 - Bearing Section
4 - Linkage
5 - Sealing Strip
PRD 50 - 100…120…130
PRD 50 - 110…120…130
PRD 50A - 110…120…130
2
39
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
PRD 50
General
(Wall Mounted)
Dampers
PRD Series
General
(Duct Mounted)
PRD 30 - 100
Description
Pressure Relief Dampers, are used in intake & discharge
openings in commercial and residential airconditioning
systems. When the ventilation system is on, the blades
of the pressure relief damper are held in the open position
by the air flow. If the system is switched off, the damper
blades close automatically, thus preventing reverse airflow
and giving protection against the ingress of untempered
air, rain and birds into the airconditioning system.
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
40
PRD 30 - 110
FRAME:
General construction as type PRD 30-100 damper but
frame & blades, all from mill finish aluminum sheets.
Gauge 18 ga. (1.2mm thk.) from formed channel frame
galvanized steel sheet.
BLADES:
Kitchen
Hoods
100mm max. width, 0.75mm thk. mill finish aluminum
sheet.
Sealing strip on blades in foam gasket.
LINKAGE:
PRD 30 - 120
Supports
& Bands
Galvanized steel sheet 28mm x 22 gauge
BEARINGS:
General construction as type PRD 30-100 damper but frame
& blades, all from galvanized steel sheets construction
with counter weight.
Bearing section in plastic 6mm.
Blade stub shafts in brass.
MINIMUM SIZE:
construction.
MAXIMUM SIZE:
PRD 30 - 130
General construction as type PRD 30-100 damper but with
frame built of stainless steel sheet type 304, 2B finish and
blades built of mill finish aluminum sheets.
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
SHAFTS:
Dampers
PRD Series
Construction - Dimensions
1 - Casing
2 - Blade
3 - Bearing Section
4 - Linkage
5 - Sealing Strip
PRD 30 - 100…120…130
PRD 30 - 100
PRD 30 - 100
2
41
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
PRD 30
General
(Duct Mounted)
Dampers
General
PRD 50
Wall Mounted
Insert Type
PRD 30
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
42
PRD Series
Dampers
PRD Series
200
150
300
200
400
250
500
300
600
350
700
400
800
450
900
500
1000
600
1100
700
1200
800
1300
900
1400
1000
1500
General
2
43
Silencers
100
Acoustic
Enclosures
H
100
Specification Text
Order Example
Pressure Relief Dampers are used for intake and discharge
openings in air conditioning systems to prevent reverse
air flow and for protection against ingress of rain into
airconditioning systems. Basically the frame is built of
galvanised steel (standard) or aluminium and corrugated
aluminium blades (standard) with blade seals opening and
closing automatically.
Product type
Kitchen
Hoods
Louvers
in Pa : Total pressure drop
in m/s : Air velocity based on W x H
PRD 50 - 100 - aaa x aaa
Supports
& Bands
PRD 50
PRD 30
Access
Doors
Sizes
STANDARD
Make : SAFID
Type : PRD50-100 - 500 x 500
.
Qty
.
Tapes &
Sealants
: 1
Flexible
Connectors
Pt
W
100
Flanges &
Accessories
V
Standard Sizes
Plenum
Boxes
Pressure Loss
Dampers
General
Spin-in Damper
SFLD Series
SFLD 10
Spin-in Collar with damper blade
FRAME:
Galvanized steel sheet (24 gauge).
2
44
BLADES:
Plain galvanized steel sheet (20 gauge).
Galvanized steel perforated blade (optional)
Silencers
FINISH:
Mill galvanized.
CASE BEARINGS:
CONTROL SHAFT:
6mm diameter zinc plated mild steel
SFLDE 10
Spin-in collar with damper blade & extractor
80mm Dia. damper up to 315mm Dia.
Description
SFLD 11 / SFLDE 11
Adjustable blade mounted with manually operated steel
reinforced plastic handle and position indicator. The
movement of the blade permits regulation from fully open
to almost closed.
General construction as type SFLD10 damper but blades,
304).
The Spin-in damper is used as take off or branch
connection.
SFLD 12 / SFLDE 12
General construction as type SFLD10 damper but with
frame, blades shafts and blade to shaft fixing all from
stainless steel (Grade 304).
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Plastic bushing
Dampers
SFLD Series
SFLD
SFLDE
Spin Collar with damper blade
Spin in collar with damper blade & extractor
General
Spin-in Damper
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
45
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Kitchen
Hoods
Pressure Loss for SFLD / SFLDE
Dampers
General
Spin-in Damper
SFLD Series
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
46
Dampers
Order
General
Standard Sizes
SFLD Series
Order example:
Dia
mm
80
L
mm
120
Product code:
100
120
125
120
SFLD 10
140
120
150
120
160
120
180
120
Acoustic
Enclosures
Plenum
Boxes
Louvers
Kitchen
Hoods
120
120
Supports
& Bands
305
315
Access
Doors
120
120
Flexible
Connectors
250
280
Diameter
2
47
Flanges &
Accessories
120
120
SFLDE 10
SFLD 10 - aaa
Tapes &
Sealants
200
224
Type
Silencers
Spin-in Damper
Dampers
Fire Damper Curtain Type
Description
Blades in Air Stream
Shutter type fire dampers provide an automatic means of
localizing areas of fire in ventilation systems.
The SSA range of curtain bladed fire dampers are suitable
for installation in walls and ceilings made from concrete
or brickwork, and will stop the spread of fire through duct,
walls or floors.
There is a wide choice of sizes available for low, medium
and high velocity applications and inlcude rectangular,
square, circular and flat oval connections.
Plenum
Boxes
Acoustic
Enclosures
2
48
Silencers
General
Constructed & Tested in accordance with British Standard (BS 476: part 20: 1987).
SSA-1 Series
Type A
The dampers are fitted with standard release 74˚C fusible
links (UL LISTED) unless otherwise specified.
FIRE DAMPER FOR USE IN STATIC SYSTEMS
FIRE RESISTANCE RATING 1-1/2 HOUR
FILE NO: R22165
SSA-1-A-100 Standard Construction
SSA-1-A-110
FRAME:
General construction as type SSA-1-A-100 damper but
blades in stainless steel (Grade 304).
Louvers
Built of 18 gauge (1.2mm) galvanized steel.
BLADES:
Access
Doors
Supports
& Bands
Kitchen
Hoods
FINISH:
Mill galvanized.
FUSIBLE LINK:
Standard release 74 ˚C. (165 ˚F) UL listed.
Other temperatures available on request.
SPRINGS:
Stainless steel closure springs.
FIRE RATING:
SSA-1-A-120
MINIMUM SIZE:
General construction as type SSA-1-A-100 damper but
frame, blades and catchplates all from stainless steel
(Grade 304).
Up to 4 hours, fire rating.
Flexible
Connectors
MAXIMUM SIZE:
Flanges &
Accessories
100 x 100mm
Tapes &
Sealants
1000 x 1000mm, as single section,
Multiple section assembly with unlimited size,
where each section operates independently.
Dampers
SSA-1 Series
Dimensions
1 - Galvanized or S/S Casing
2 - Galvanized or S/S Blades
3 - Fusible Link 74 ˚C (UL listed)
4 - Top Blade riveted to frame
5 - S/S closure spring.
6 - Catch plates.
General
2
49
Damper Blades in Air System
W x H = Duct Size
Horizontal Mounting
Tapes &
Sealants
Horizontal Mounting
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Vertical Mounting
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
SSA - 1 - A…
Vertical Mounting
Dampers
Damper Blades Outside Air Stream
Description
Shutter type fire dampers provide an automatic means of
localizing areas of fire in ventilation systems.
2
50
walls or floors.
Silencers
General
SSA-1 Series
Type B
Plenum
Boxes
Acoustic
Enclosures
links (UL LISTED) unless otherwise specified.
FILE NO: R22165
SSA-1-B-100 Standard Construction
SSA-1-B-110
FRAME:
General construction as type SSA-1-B-100 damper but
Louvers
BLADES:
Access
Doors
Supports
& Bands
Kitchen
Hoods
FINISH:
Mill galvanized.
FUSIBLE LINK:
SPRINGS:
FIRE RATING:
SSA-1-B-120
MINIMUM SIZE:
General construction as type SSA-1-B-100 damper but
(Grade 304).
Flexible
Connectors
MAXIMUM SIZE:
Flanges &
Accessories
100 x 100mm
Tapes &
Sealants
Multiple section assembly with unlimited size,
where each section operates independently.
Dampers
SSA-1 Series
Dimensions
Damper Blades outside Air Stream
6 - Catch plates.
General
2
51
Vertical Mounting
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
SSA - 1 - B…
Vertical Mounting
129
184
244
299
354
409
469
529
589
644
699
754
814
869
954
979
1044
1099
1159
Supports
& Bands
35
40
50
55
60
65
75
85
95
100
105
110
120
125
130
135
150
155
165
Access
Doors
100
150
200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
1000
Flexible
Connectors
Y
Over all
Damper Height
H+Y-6
Flanges &
Accessories
Horizontal Mounting
DUCT
HEIGHT
H
Tapes &
Sealants
Horizontal Mounting
Kitchen
Hoods
W x H = Duct Size
Dampers
Damper Frame & Blades (100% free area)
Description
Fire dampers provide an automatic means of localizing
areas of fire in ventilation systems.
2
52
walls or floors.
Silencers
General
SSA-1 Series
Type C
Plenum
Boxes
Acoustic
Enclosures
links unless otherwise specified.
FILE NO: R22165
SSA-1-C-100 Standard Construction
SSA-1-C-110
FRAME:
General construction as type SSA-1-C-100 damper but
Louvers
BLADES:
Access
Doors
Supports
& Bands
Kitchen
Hoods
FINISH:
Mill galvanized.
FUSIBLE LINK:
SPRINGS:
FIRE RATING:
SSA-1-C-120
MINIMUM SIZE:
General construction as type SSA-1-C-100 damper but
(Grade 304).
Flexible
Connectors
MAXIMUM SIZE:
Flanges &
Accessories
100 x 100mm
Tapes &
Sealants
Dampers
SSA-1 Series
Dimensions
Damper Frame & Blades (100% free area)
6 - Catch plates.
General
2
53
Vertical Mounting
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
SSA - 1 - C…
Vertical Mounting
129
184
244
299
354
409
469
529
589
644
699
754
814
869
954
979
1044
1099
1159
Supports
& Bands
35
40
50
55
60
65
75
85
95
100
105
110
120
125
130
135
150
155
165
Access
Doors
100
150
200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
1000
Flexible
Connectors
Y
Over all
Damper Height
H+Y-6
Flanges &
Accessories
Horizontal Mounting
DUCT
HEIGHT
H
Tapes &
Sealants
Horizontal Mounting
Kitchen
Hoods
W x H = Duct Size
Dampers
Description
Damper with Spigot, Round
2
54
walls or floors.
Silencers
General
SSA-1 Series
Type R
Plenum
Boxes
Acoustic
Enclosures
FILE NO: R22165
SSA-1-R-100 Standard Construction
SSA-1-R-110
FRAME:
General construction as type SSA-1-R-100 damper but
Louvers
BLADES:
Supports
& Bands
Kitchen
Hoods
FINISH:
Mill galvanized.
FUSIBLE LINK:
SPRINGS:
SSA-1-R-120
General construction as type SSA-1-R-100 damper but
(Grade 304).
MINIMUM SIZE:
Flexible
Connectors
100 x 100mm
MAXIMUM SIZE:
Flanges &
Accessories
Access
Doors
FIRE RATING:
Tapes &
Sealants
Dampers
SSA-1 Series
Dimensions
Damper with Spigot, Round
6 - Catch plates.
General
2
55
Vertical Mounting
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
SSA - 1 - R…
170
230
285
340
395
455
515
575
630
685
740
800
855
910
965
1030
1085
1145
1200
Supports
& Bands
40
50
55
60
65
75
85
95
100
105
110
120
125
130
135
150
155
165
170
Access
Doors
100
150
200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
1000
Flexible
Connectors
Y
Over all
Damper Height
D + Y + 30
Flanges &
Accessories
Horizontal Mounting
DAMPER
HEIGHT
D
Tapes &
Sealants
Horizontal Mounting
Kitchen
Hoods
Vertical Mounting
Dampers
Damper with Spigot, Oval Type
Description
2
56
walls or floors.
Silencers
General
SSA-1 Series
Type O
Plenum
Boxes
Acoustic
Enclosures
FILE NO: R22165
SSA-1-O-100 Standard Construction
SSA-1-O-110
FRAME:
General construction as type SSA-1-O-100 damper but
Louvers
BLADES:
Supports
& Bands
Kitchen
Hoods
FINISH:
Mill galvanized.
FUSIBLE LINK:
SPRINGS:
SSA-1-O-120
4 hours, fire rating.
General construction as type SSA-1-O-100 damper but
(Grade 304).
MINIMUM SIZE:
Flexible
Connectors
100 x 100mm
MAXIMUM SIZE:
Flanges &
Accessories
Access
Doors
FIRE RATING:
Tapes &
Sealants
Dampers
SSA-1 Series
Dimensions
Damper with Spigot, Oval Type
6 - Catch plates.
General
2
57
Vertical Mounting
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
SSA - 1 - O…
170
230
285
340
395
455
515
575
630
685
740
800
855
910
965
1030
1085
1145
1200
Supports
& Bands
40
50
55
60
65
75
85
95
100
105
110
120
125
130
135
150
155
165
170
Access
Doors
100
150
200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
1000
Flexible
Connectors
Y
Over all
Damper Height
H + Y + 30
Flanges &
Accessories
Horizontal Mounting
DAMPER
HEIGHT
H
Tapes &
Sealants
Horizontal Mounting
Kitchen
Hoods
Vertical Mounting
Dampers
General
SSA-1 Series
Product Range
Construction Variants
Construction
Variants
Description
A
Blades in airstream, square, round or
rectangular spigot, fitted with closing
springs and catchplates.
Vertical/horizontal
mounting
Low
Medium
A1
As code A but includes side seals.
Vertical/horizontal
mounting
Low
Medium
A2
As code A but excludes closing springs
and catchplates.
Vertical mounting only
Low
Medium
Variable height top case section to
contain blades out of airstream. Fitted
with closing springs and catchplates.
Can be supplied with square or
rectangular, circular or oval duct
connections.
Vertical/horizontal
mounting
High
As code B, C series but includes
side seals
Vertical/horizontal
mounting
High
Mounting Mode
Velocity Range
Supports
& Bands
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
58
B
C
R
Access
Doors
O
B1
R1
O1
Accessories
Please see page 59 of this chapter.
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
C1
Dampers
SSA-1 Series
General
Accessories
Combined with
Base holder with fuse link (standard construction)
Code
-
Microswitch indicates blades "CLOSED"
(INDICATES BLADES CLOSED)
S 01
S 02
VISUAL INDICATOR
Louvers
(INDICATES BLADES CLOSED)
Mechanical device to indicate blade closure visible externally
from the damper.
Kitchen
Hoods
Supports
& Bands
Interruption of electical current to activate closure of the curtain
blade pack.
S 04
SOLENOID - A.C. VOLTAGE:
Electrically energised to activate closure of the curtain blade
pack.
Normally "DE-ENERGISED" activated by an eletrical impulse
from either/via a detector or control panel. The solenoid can
be fitted for standard "direct link" operation.
For maintenance/servicing the solenoid can be manually overridden for testing purposes.
Access
Doors
As an alternative to the solenoid for systems that require
normally "ENERGISED" actuators that automatically operate
in the event of an interruption of electrical supply. (Voltage
24V, 110V & 240V). Standard fuse temperature 74˚C.
S 05
Flexible
Connectors
ELECTRO-MAGNET-A.C and D.C. VOLTAGE
S 03
Flanges &
Accessories
Mechanical device to indicate blade
closure visable externally from the
damper.
MICRO-SWITCH WITH VISUAL INDICATOR
Plenum
Boxes
Acoustic
Enclosures
To provide "remote" indication of wether the blade is "open
or closed". The microswitch can also be connected to any
warning device or into the control circuit of a ventilation system
to isolate the plant in event of fire.
Tapes &
Sealants
ELECTRICAL MICRO-SWITCH.
2
59
Silencers
Construction or Construction Variant
Dampers
General
SSA-1 Series
Installation Details for Type A
SSA-1-A
Damper Installed to Duct
Damper Installed to Wall
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
60
Dampers
SSA-1 Series
General
Installation Details for Type B
SSA-1-B
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Damper Installed to Wall
Tapes &
Sealants
Damper Installed to Duct
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
61
Dampers
General
SSA-1 Series
Installation Details with Sleeve and Peripheral Angle for Type C
SSA-1-C
Damper with Rectangular Spigot
Damper with Round Spigot
Damper with Oval Spigot
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
62
Dampers
SSA-1 Series
Installation Details with HEVAC Frame for Type C
SSA-1-C
Damper with Rectangular Spigot
General
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Damper with Oval Spigot
Tapes &
Sealants
Damper with Round Spigot
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
63
Dampers
SSA-1 Series
General
Fire Resistance test utilizing the heating conditions of (BS 476: part 20: 1987).
Warres 49800, Fire Resistance up to 1 hr
Warres 49800, Fire Resistance up to 2 hrs
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
64
Dampers
SSA-1 Series
Technical Data
Fire Test BS 476 Part 20 1987
The fire dampers shown have been tested by an independent authority (Warrington Research Centre) according to British
Standards 476 Part 20; 1987 for a period of 4 hours.
2
65
Silencers
The time / temperature curve required by this test procedure is shown below, after 4 hours test the SSA retained its
integrity with no significant openings being formed.
General
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Fire Test BS 476 Part 20: 1987
Dampers
General
Order Details
Order Code
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
66
SSA-1-B-100 - V
Type
SSA-1
A
B
C
R
O
A1
B1
C1
R1
O1
= Blades in air stream
= Blades out of air stream
(Circular type)
(Oval type)
Variants - Seals
/
500 x 500
/
S 01
Duct Size
Flat oval 'B' x 'H' mm. All
damper spigots are
manufactured down on
duct size to fit inside
ductwork connections
Accessories
(See page 59)
Mounting
V = Vertical Damper
H = Horizontal Damper
100
110
120
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Kitchen
Hoods
Louvers
SSA-1 Series
Dampers
SSA-1 Series
Specification Text
Order Example
Square or rectangular shutter type fire dampers for the
isolation of fire zones in air conditioning systems. Designed
and fabricated to maintain integrity and stability for 4
hours when tested to BS 476 Part 20; 1987. The SSA fire
dampers consists of perimeter frame case and interlocking
shutter type blades. As standard the case is complete
with catchplates and constant tension closure springs.
Suitable for either rectangular, circular or flat oval ducting
and available in high or low pressure/velocity construction.
Standard release 74˚C fusible link.
STANDARD
.
.
.
2
67
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
Make : SAFID
Type : SSA-1-A-100-500 x 500
Qty : 1
General
Dampers
Blade Type Fire Damper
FD Series
General
Constructed & Tested in accordance with UL555 Standard.
FD 30 - 100
Description
Blade type Fire Damper type FD 30 provide means of
localizing areas of fire in ventilation systems. It prevents the
distribution of fire through ventilation ductworks. FD offers
an effective barrier maintaining integrity in a fire situation.
It is suitable for installation in sheet metal ductworks or in
walls or ceiling slabs made from concrete, brick & lightweight
partition walls. FD is available for rectangular, square,
circular & flat oval duct fixings.
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
68
FD 30 - 110
FRAME:
General construction as type FD30-100 damper but
blades, shafts and blade to spindle fixing in stainless
steel (Grade 304).
Louvers
180mm x 30mm x 1.5mm (16 ga.) galvanized steel, formed
channel for flange connections.
BLADES:
250mm max. width,1.5mm (16 ga.) galvanized steel.
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Kitchen
Hoods
FINISH:
Mill galvanized.
LINKAGE:
Parallel blade have standard face linkage operation.
Linkage consist of 6mm dia. S/S pivot pins.
CASE BEARINGS:
Made sintered bronze (oilite), operational temp. resistanace
up to 200 ˚C.
FUSIBLE LINK:
FD 30 - 120
SPRING:
General construction as type FD30-100 damper but with
case, blades shafts and blade to shaft fixing and linkage
Standard release 74 ˚C (165 ˚F) UL listed
Stainless steel closure spring mounted internally with
catch device to prevent blades from opening until manually
released.
MINIMUM SIZE:
construction.
MAXIMUM SIZE:
Dampers
FD Series
Dimensions
1 - Casing
2 - Blade
3 - Face Linkage
4 - Linkage Bar
5 - Landing Angles
7 - Catch Device
8 - Closing Spring
9 - Side Seal
General
(Flange Type)
2
69
Flange Type, Parallel Blades
Parallel Blade (PB)
100
150
200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
1000
200
250
300
350
400
450
500
600
700
800
900
1000
1
1
2
2
2
2
3
3
4
4
5
6
Supports
& Bands
Number
of Blades
Access
Doors
H
in mm
Flexible
Connectors
W
in mm
Flanges &
Accessories
Standard Sizes
Tapes &
Sealants
Flange Type
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
FD30 - 100…110…120
Dampers
FD Series
(Sleeve Type)
General
FD 40 - 100
Description
Blade type Fire Damper FD 40 provide an automatic means
of localizing areas of fire in ventilation systems. It prevent
the distribution of fire through ventilation ductworks. FD
offer an effective barrier maintaining integrity in a fire
situation up to 3 hrs. It is suitable for installation in sheet
metal ductworks or in walls or ceiling slabs made from
concrete, brick & lightweight partition walls. FD is available
for rectangular, square, circular & flat oval duct fixings.
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
70
FD 40 - 110
FRAME:
steel (Grade 304).
Louvers
BLADES:
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Kitchen
Hoods
FINISH:
Mill galvanized.
LINKAGE:
CASE BEARINGS:
up to 200 ˚C.
FUSIBLE LINK:
FD 40 - 120
SPRING:
released.
MINIMUM SIZE:
construction.
MAXIMUM SIZE:
Dampers
FD Series
Dimensions
1 - Casing
2 - Blade
3 - Face Linkage
4 - Linkage Bar
5 - Landing Angles
7 - Catch Device
8 - Closing Spring
9 - Side Seal
General
(Sleeve Type)
2
71
150
200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
1000
200
250
300
350
400
450
500
600
700
800
900
1000
1
1
1
2
2
2
3
3
4
4
5
6
Parallel Blade (PB)
Supports
& Bands
Number
of Blades
Access
Doors
H
in mm
Flexible
Connectors
W
in mm
Flanges &
Accessories
Standard Sizes
Tapes &
Sealants
Sleeve Type
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
FD40 - 100…110…120
Dampers
FD Series
General
FD 50 - 100
Description
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
72
FD 50 - 110
FRAME:
steel (Grade 304).
Louvers
180mm x 1.5mm (16 ga.) galvanized steel, L = 405mm.
BLADES:
FINISH:
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Kitchen
Hoods
Mill galvanized.
LINKAGE:
CASE BEARINGS:
up to 200 ˚C.
FUSIBLE LINK:
FD 50 - 120
SPRING:
released.
MINIMUM SIZE:
construction.
MAXIMUM SIZE:
Dampers
FD Series
Dimensions
1 - Casing
2 - Blade
3 - Face Linkage
4 - Linkage Bar
5 - Landing Angles
7 - Catch Device
8 - Closing Spring
9 - Side Seal
General
2
73
Circular Spigot Type, Parallel Blades
Parallel Blade (PB)
100
150
200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
1000
200
250
300
350
400
450
500
600
700
800
900
1000
1
1
2
2
2
2
3
3
4
4
5
6
Supports
& Bands
Number
of Blades
Access
Doors
H
in mm
Flexible
Connectors
W
in mm
Flanges &
Accessories
Standard Sizes
Tapes &
Sealants
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
FD50 - 100…110…120
Dampers
FD Series
(Oval Spigot Type)
General
FD 60 - 100
Description
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
74
FD 60 - 110
FRAME (SPIGOT TYPE)
steel (Grade 304).
Louvers
180mmx1.5mm (16 ga) galvanized steel, L=405mm.
BLADES:
FINISH:
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Kitchen
Hoods
Mill galvanized.
LINKAGE:
CASE BEARINGS:
up to 200 ˚C.
FUSIBLE LINK:
FD 60 - 120
SPRING:
Standard release 74 ˚C. (165 ˚F) UL listed
released.
MINIMUM SIZE:
construction.
MAXIMUM SIZE:
Dampers
FD Series
Dimensions
1 - Casing
2 - Blade
3 - Face Linkage
4 - Linkage Bar
5 - Landing Angles
7 - Catch Device
8 - Closing Spring
9 - Side Seal
General
(Oval Spigot Type)
2
75
Oval Spigot Type, Parallel Blades
Parallel Blade (PB)
100
150
200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
1000
200
250
300
350
400
450
500
600
700
800
900
1000
1
1
2
2
2
2
3
3
4
4
5
6
Supports
& Bands
Number
of Blades
Access
Doors
H
in mm
Flexible
Connectors
W
in mm
Flanges &
Accessories
Standard Sizes
Tapes &
Sealants
Oval Spigot Type
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
FD60 - 100…110…120
Dampers
FD Series
(Rectangular Spigot Type)
General
FD 70 - 100
Description
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
76
FD 70 - 110
FRAME (SPIGOT TYPE)
steel (Grade 304).
Louvers
180mmx1.5mm (16 ga) galvanized steel, L=405mm
BLADES:
FINISH:
Supports
& Bands
Kitchen
Hoods
Mill galvanized.
LINKAGE:
CASE BEARINGS:
up to 200 ˚C.
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
FUSIBLE LINK:
FD 70 - 120
Standard release 74 ˚C. (165 ˚F) UL listed
SPRING:
released.
MINIMUM SIZE:
construction.
MAXIMUM SIZE:
Dampers
FD Series
Dimensions
1 - Casing
2 - Blade
3 - Face Linkage
4 - Linkage Bar
5 - Landing Angles
7 - Catch Device
8 - Closing Spring
9 - Side Seal
General
2
77
Rectangular Spigot Type, Parallel Blades
Parallel Blade (PB)
100
150
200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
1000
200
250
300
350
400
450
500
600
700
800
900
1000
1
1
1
2
2
2
3
3
4
4
5
6
Supports
& Bands
Number
of Blades
Access
Doors
H
in mm
Flexible
Connectors
W
in mm
Flanges &
Accessories
Standard Sizes
Tapes &
Sealants
Rectangular Spigot Type
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
FD70 - 100…110…120
Dampers
General
FD Series
Installation Details with Sleeve and Peripheral Angle
FD
FD 50, Circular Spigot Type
FD 60, Oval Spigot Type
FD 70, Rectangular Spigot Type
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
78
Dampers
FD Series
Installation Details with HEVAC Frame
FD
FD 50, Circular Spigot Type
General
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
FD 70, Rectangular Spigot Type
Tapes &
Sealants
FD 60, Oval Spigot Type
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
79
Dampers
General
Product Range
FD - 100, 110, 120
Casing
Seals
Construction
Variants
Description
FD 30
FD 40
Standard supply construction
flange type frame 180mm x 30mm
from 1.5mm (16 gauge) galvanized
steel sheet.
Sleeve case inverted channel frame
180mm width from 1.5mm (16 gauge)
galvanized steel sheet.
FD 50
Spigot case detail from 1.5mm
galvanized steel sheet. Total length
405mm including circular spigot.
FD 60
galvanized steel sheet. Total length
405mm including oval spigot.
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
80
FD Series
Supports
& Bands
FD 70
galvanized steel sheet. Total
length 405mm including rectangular
spigot.
Access
Doors
Side seals. Fitted to
close gap between case
and blades.
Switches
S 01
Construction
Variants
Description
PB
internal face linkage, parallel blade
operation only.
Flexible
Connectors
Flanges &
Accessories
S1
No seals
Not applicable
Accessories & Types
Linkage
Tapes &
Sealants
S
Description
Microswitch
Bearings
Construction
Variants
Description
B1
oilite.
B2
Stainless steel
Dampers
FD Series
General
Order Details
Order Code
FD 30 - 100
/
Variants - Case
Variants - Bearings
*B1 = Sintered bronze (oilite)
B2 = Stainless Steel
Plenum
Boxes
Type
*100 (std supply)
110
120
Acoustic
Enclosures
Square or rectangular Dimensions 'W' x 'H' mm
Flat oval 'B' x 'H' mm. All damper spigots are
manufactured down on duct size to fit inside
ductwork connections.
Silencers
Duct Size
* FD 30 = Flange
(Standard Supply)
FD 40 = Sleeve
FD 50 = Circular Spigot
FD 60 = Oval Spigot
FD 70 = Rectangular Spigot
Kitchen
Hoods
Louvers
Variants - Seals
S
= No seal, not applicable for FD type
*S1
= Side seal only (standard supply)
Specification
Order Example
Rectangular, square, circular & flat oval blade type Fire
Damper designed for fire isolation of sections of ducting
in ventilation systems. Basically consisting of a flanged
casing, shut off blades with overlapping interlocking joints
with side seals to close gap between case and blades,
with internal fusible link control and stainless steel closing
spring. Blades are connected by internal linkage for parallel
blade operation.
STANDARD
.
.
.
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Make : SAFID
Type : FD 30 - 100 - S1 - B1 - 500 x 500
Qty : 1
Supports
& Bands
* Stands for Standard Supply.
Access
Doors
Linkage
*PB - Parallel Blades
2
81
500 x 500
'DPSHUV
CFSD Series
*HQHUDO
&RPELQDWLRQ)LUH6PRNH'DPSHU
7DSHV
6HDODQWV
)ODQJHV
$FFHVVRULHV
)OH[LEOH
&RQQHFWRUV
$FFHVV
'RRUV
6XSSRUWV
%DQGV
.LWFKHQ
+RRGV
/RXYHUV
3OHQXP
%R[HV
$FRXVWLF
(QFORVXUHV
6LOHQFHUV
COMBINATION FIRE AND SMOKE DAMPER
O
1-1/2 HR LEAKAGE RESISTANCE CLASS II 250 F
FILE NO: R22165
Product Description
Combination Fire / Smoke dampers provide an automatic means of localizing areas of smoke and or fire in
ventilation systems that is greatly contribute to the safety of life and property in the early stage of fire. It
prevents the spread of fire and or smoke through ventilation ductworks or wall openings. These type
dampers offer an effective fire or smoke barrier maintaining the integrity in a fire situation and it is
combined with low leakage characteristic for smoke management. It is suitable for installation in sheet
metal ductworks or in walls or ceiling slabs made from concrete, brick and lightweight partition walls.
In today's life safety products markets, many building code require Fire dampers, Smoke dampers and
Combination Fire & Smoke dampers to be inspected for proper operation. Usually Fire and Combination
Fire & Smoke dampers are supplied with a fusible linkage that is a one time device and generally limited
within a specified temperature rating (165 or 212°F). Once this link has meet the elevated temperature, it
can no longer be used and must be replaced with an identical link for further operation.
"SAFID" introducing "ERL" Thermoelectric Tripping Device (heat sensor) to replace the existing high
torque spring / fusible link fire closure mechanism in all Combination Fire & Smoke dampers and blade
type Fire dampers. The "ERL" is thermally responsive bimetal disc / sensor that open and close the
electrical contacts at a specific factory calibrated temperature setting.
The "ERL" is available in fixed temperature setting at 165°F (74 °C) only. The "ERL" sensor is a manual
reset type and can be reset after the temperature has cooled down below the sensor set point. This feature
allow the ease of operating and resetting the damper in a matter of seconds without replacing the links. It
is reusable / ressettable heat responsive device that can only be reset after a visual inspection of the
damper.
The "ERL" requires factory installation and wiring together with the qualified actuator to meet "UL"
requirements. The "ERL" in combination with a qualified electric actuators provides controlled closure and
eliminates the instantaneous damper closure associated with traditional fusible links that can damage the
entire ductworks. The duct smoke detector can be wired in series with the "ERL" to close the damper
during smoke control mode.
Dampers which allow remote resetting of the damper from a remote location are dangerous. All damper
moving parts must be inspected and cycled at every six months and in accordance with "NFPA90A & 92A"
latest edition and local codes.
5LJKWWRDOWHUDWLRQVUHVHUYHG
‫م‬٢٠١٠
LVDUHJLVWHUHGWUDGHPDUN
FRS\ULJKW6$),'1$OO5LJKWV5HVHUYHG
'DPSHUV
CFSD Series
*HQHUDO
Types
1. Sleeve Type (Model: CFSD-40)
2. Circular Type (Model: CFSD-50)
3. Oval Type (Model: CFSD-60)
4. Factory Installed Sleeve (Model: CFSD-80)
Blade tip seal
Jack shaft
Minimum Size
Maximum Size
Mounting
Velocity
914W x 914H mm - Single section
Vertical
2400 FPM
$FFHVV
'RRUV
6XSSRUWV
%DQGV
Thermoelectric Tripping Device (ERL)
Model: BAE165 US
Bimetallic manual reset type.
165°F (74°C) rated
UL listed.
3OHQXP
%R[HV
Frame
Blade stop
Linkage
Bearings
/RXYHUV
Blades
Mill Galvanized
1.5mm thick (Ga.16) galvanized steel "Triple Vee" (3V) groove type
(standard).
130 x 24.5 x 1.5mm thick (Ga.16) galvanized steel hat channel.
1.5mm thick (Ga.16) galvanized steel sheet bend at 45º angle.
Side linkage concealed in frame. (Standard)
Sintered Bronze oilite type.
Compression type stainless steel grade 304, 0.3mm thick fastened between
case and blades by blade axles.
Blade tip seals are high temperature Charcoal Dense Silicone Rubber.
Zinc plated mild steel 12mm Round across the blade length and 10 x 10mm
square end x 25mm long to suit with the actuator.
200W x 150H mm. Single blade construction up to 250mm height.
Damper Actuators - With Spring Return
a. Two Position (Open / Close) Type:
1. BELIMO Model: BF-ME (24 - 230VAC)
2. BELIMO Model: BF-S-ME (24 - 230VAC) with built-in Auxiliary Switch.
7DSHV
6HDODQWV
)ODQJHV
$FFHVVRULHV
For Belimo Actuator details see pages 126 - 127.
)OH[LEOH
&RQQHFWRUV
Finish
.LWFKHQ
+RRGV
$FRXVWLF
(QFORVXUHV
6LOHQFHUV
‫م‬٢٠١٠
'DPSHUV
CFSD Series
*HQHUDO
Dimensions
Sleeve Type
Model: CFSD-40
4
1
6LOHQFHUV
3
7
10
5
$FRXVWLF
(QFORVXUHV
8
2
11
9
6
7DSHV
6HDODQWV
)ODQJHV
$FFHVVRULHV
)OH[LEOH
&RQQHFWRUV
$FFHVV
'RRUV
6XSSRUWV
%DQGV
.LWFKHQ
+RRGV
/RXYHUV
3OHQXP
%R[HV
4
1. Casing
2. Linkage bracket
3. Blade
4. Linkage bar
5. Bearings
6. Blade stop
7. Side seal
8. Blade tip seal
9. Lock washer and galvanized round washer
10. Kneelock
11. Jack shaft
‫م‬٢٠١٠
'DPSHUV
CFSD Series
*HQHUDO
Dimensions
Circular Type
Model: CFSD-50
.LWFKHQ
+RRGV
/RXYHUV
3OHQXP
%R[HV
$FRXVWLF
(QFORVXUHV
6LOHQFHUV
5
7DSHV
6HDODQWV
)ODQJHV
$FFHVVRULHV
)OH[LEOH
&RQQHFWRUV
$FFHVV
'RRUV
6XSSRUWV
%DQGV
Flat Oval Type
Model: CFSD-60
‫م‬٢٠١٠
'DPSHUV
CFSD Series
*HQHUDO
6
Dimensions
CFSD with factory installed Sleeve, ERL & Actuator
Model: CFSD-80
1
6LOHQFHUV
2
3
/RXYHUV
3OHQXP
%R[HV
$FRXVWLF
(QFORVXUHV
4
10
11
5
12
6
13
7
.LWFKHQ
+RRGV
8
14
9
7DSHV
6HDODQWV
)ODQJHV
$FFHVVRULHV
)OH[LEOH
&RQQHFWRUV
$FFHVV
'RRUV
6XSSRUWV
%DQGV
15
1. Damper frame
2. Blade
3. Thermoelectric tripping device
4. Sleeve
5. Linkage Bracket
6. Lock washer and galvanized round washer
7. Kneelock
8. Linkage bar
9. Actuator
10. Bearing
11. Blade tip seal
12. Side seal
13. Jack shaft
14. Blade stop
15. Power supply
‫م‬٢٠١٠
'DPSHUV
CFSD Series
*HQHUDO
Dimensions
7
7DSHV
6HDODQWV
)ODQJHV
$FFHVVRULHV
)OH[LEOH
&RQQHFWRUV
$FFHVV
'RRUV
6XSSRUWV
%DQGV
.LWFKHQ
+RRGV
/RXYHUV
3OHQXP
%R[HV
$FRXVWLF
(QFORVXUHV
6LOHQFHUV
CFSD with factory installed Sleeve, ERL & Actuator
Model: CFSD-80
‫م‬٢٠١٠
'DPSHUV
CFSD Series
*HQHUDO
Dimensions
Model: CFSD
Blades Profiles:
7DSHV
6HDODQWV
)ODQJHV
$FFHVVRULHV
)OH[LEOH
&RQQHFWRUV
$FFHVV
'RRUV
6XSSRUWV
%DQGV
.LWFKHQ
+RRGV
/RXYHUV
3OHQXP
%R[HV
$FRXVWLF
(QFORVXUHV
6LOHQFHUV
8
Note:
All blades are constructed from galvanized steel sheet gauge 16.
‫م‬٢٠١٠
'DPSHUV
CFSD Series
*HQHUDO
Dimensions
Model: CFSD
9
7DSHV
6HDODQWV
)ODQJHV
$FFHVVRULHV
)OH[LEOH
&RQQHFWRUV
$FFHVV
'RRUV
6XSSRUWV
%DQGV
.LWFKHQ
+RRGV
/RXYHUV
3OHQXP
%R[HV
$FRXVWLF
(QFORVXUHV
6LOHQFHUV
Linkage Assembly:
‫م‬٢٠١٠
'DPSHUV
CFSD Series
*HQHUDO
CFSD with Factory Installed Sleeve, ERL & Actuator (Typical Installation)
7DSHV
6HDODQWV
)ODQJHV
$FFHVVRULHV
)OH[LEOH
&RQQHFWRUV
$FFHVV
'RRUV
6XSSRUWV
%DQGV
.LWFKHQ
+RRGV
/RXYHUV
3OHQXP
%R[HV
$FRXVWLF
(QFORVXUHV
6LOHQFHUV
90
Notes:
1. Airflow can be at opposite direction.
2. The actuator and ERL can be located in either side of the wall.
3. Refer to installation manual for further installation details.
‫م‬٢٠١٠
'DPSHUV
CFSD Series
*HQHUDO
Actuators
Fire Mode: The ERL (Thermoelectric Tripping Device) resettable link has a thermal sensor switch that
interrups the power supply to the fire & smoke control actuator as soon as the duct temperature exceeds
165ºF caused by a fire. When the power supply is interrupted, the energy stored in the spring of the fire &
smoke damper actuator moves the damper back to its safe position. The damper can be open again by
pressing the reset button on ERL after the temperature cooled down below 165ºF.
6XSSRUWV
%DQGV
Smoke Mode: When a signal detected through normally closed smoke detector (by others) connection,
the power supply to the fire & smoke damper actuator will be interrupted. The energy stored in the damper
actuator moves the damper back to its safe position and remain closed until the smoke signal close down.
The system will reset after power is reapplied to the actuator and damper will open. By placing an optional
control switch (by others) in the closed position can be close the damper if required at any time.
3OHQXP
%R[HV
Sequence of operation:
/RXYHUV
ERL Model: BAE165US
.LWFKHQ
+RRGV
BELIMO Model: BF230-S-ME
$FRXVWLF
(QFORVXUHV
6LOHQFHUV
91
7DSHV
6HDODQWV
)ODQJHV
$FFHVVRULHV
)OH[LEOH
&RQQHFWRUV
$FFHVV
'RRUV
Typical Wiring Diagrams
‫م‬٢٠١٠
'DPSHUV
CFSD Series
*HQHUDO
Order Code:
CFSD-40-100-3V-PB-R-A1-V1 / 500x500
Variants
Duct Size
Width x Height or Diameter
All damper's spigot sizes (slip-in
type) will be manufactured less
than the duct size to fit inside the
ductwork connections.
CFSD-40 = Sleeve Type
CFSD-50 = Circular Spigot
CFSD-60 = Oval Spigot
CFSD-80 = Factory Installed Sleeve
3OHQXP
%R[HV
$FRXVWLF
(QFORVXUHV
6LOHQFHUV
92
Order Details
Power Supply
Type
V1 = 24VAC
V2 = 24VDC
100 = Galvanized Steel Construction
110 = Stainless Steel (304) Construction
V3 = 120VAC
V4 = 230VAC
/RXYHUV
Type Of Blades
A1 = BELIMO BF-ME
3V = V Groove Type
A1S = BELIMO BF-S-ME
.LWFKHQ
+RRGV
Actuator
Linkage
External Controls
R = Right hand (Standard Supply)
L = Left hand
Type of Sensor
ERL = Thermoelectric Tripping Device, Model: BAE165 US
7DSHV
6HDODQWV
)ODQJHV
$FFHVVRULHV
)OH[LEOH
&RQQHFWRUV
$FFHVV
'RRUV
6XSSRUWV
%DQGV
PB = Side linkage Parallel Blade Operation
‫م‬٢٠١٠
'DPSHUV
Combination Fire/Smoke Dampers with the
following specifications shall be used in heating,
ventilating and air conditioning duct systems
passing through masonry walls, gypsum fire
resistive walls or partitions, floor slabs and for use
in smoke control systems in accordance with
Standard for Installation of Air Conditioning and
Ventilating Systems, NFPA 90A.
SAFID
Combination
Fire/Smoke
Damper,
galvanized steel construction, 3V groove blade for
parallel blades operation, 500mm width X 500mm
height duct size and right hand side external
controls. Damper with factory installed sleeve and
230 VAC BELIMO actuator with built-in auxiliary
switch and with thermoelectric tripping device
BAE165 US.
Combination Fire/Smoke Dampers shall be tested
and classified by Underwritters Laboratories Inc.
in accordance with the standards; UL555
Standard for Safety, Fire Dampers and UL55S
Standard for Safety, Smoke Dampers.
Make : SAFID
Type : CFSD-80-100-3V-PB-R-A1S-V4-ERL / 500x500
Qty. : 1
.LWFKHQ
+RRGV
/RXYHUV
3OHQXP
%R[HV
Combination Fire/Smoke Dampers shall have a
fire resistant rating of 1 ½ hour and minimum air
leakage Class II with elevated test temperature of
250 ºF. It shall be tested at 2400FPM air velocity
at 4.5 in. W.G. static pressure to be rated at
2000FPM air velocity at 4 in. W.G. static pressure.
It shall be fitted with BELIMO spring return
actuator and thermoelectric tripping device (ERL)
with temperature rating of 165 ºF (74 ºC). ERL
shall cut-off power supply to actuator in case of
fire that will activate the spring return to close the
damper blades.
93
6LOHQFHUV
Order Example
$FRXVWLF
(QFORVXUHV
Specification Text
*HQHUDO
CFSD Series
7DSHV
6HDODQWV
)ODQJHV
$FFHVVRULHV
)OH[LEOH
&RQQHFWRUV
$FFHVV
'RRUV
6XSSRUWV
%DQGV
Damper blades shall be with external linkage and
parallel action, Ga.16 galvanized steel with 3V
groove type for longitudinal reinforcement. Blade's
tip seal shall be Type: 60 Durometer Charcoal
Dense Silicone, meets gasket requirements of
UL555S. Blade's axle shall be 9.5 X 9.5mm
square forced-fit to one stub shaft secured to
blade with 4 pieces of bolt & nut, and with sintered
bronze oilite axle bearing. Jamb seal/side seal
shall be stainless steel to fill gap between blade's
end and frame. Jackshaft shall be Ø12mm
galvanized steel with a crank and kneelock
secured to the linkage bracket. Damper frame
shall be Ga.16 galvanized steel formed into hat
channel shape.
‫م‬٢٠١٠
Dampers
Combination Fire/Smoke Damper
FSD Series
(Flange Type)
General
FSD 30 - 100
Description
Combination Fire/Smoke Damper type, FSD30 provide
an automatic means of localizing areas of smoke & or
fire in ventilation systems. It prevent the distribution of fire
& / or smoke through ventilation ductworks. FSD offer an
effective barrier maintaining integrity in a fire situation and
this is combined with low leakage characteristic for smoke
management. It is suitable for installation in sheet metal
ductworks or in walls or ceiling slabs made from concrete,
brick & lightweight partition walls.
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
94
FSD 30 - 110
FRAME:
General construction as type FSD 30-100 damper but
blades, shafts and blade to spindle fixing in stainless steel
(Grade 304).
Louvers
180mm x 30 mm x 1.5mm (16 ga) galvanized steel, formed
for flange connections.
BLADES:
FINISH:
Supports
& Bands
Kitchen
Hoods
Mill galvanized.
LINKAGE:
Face linkage, parallel blade operation is standard.
Linkage consist of 6mm dia. S/S steel pivot pins.
CASE BEARINGS:
up to 200 ˚C.
Access
Doors
FUSIBLE LINK:
Standard release 74 ˚C. (165 ˚F) is std. (UL listed)
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
SEALS:
FSD 30 - 120
General construction as type FSD 30-100 damper but with
Side seal are compession type stainless steel grade 304
to close gap between case & blades.
MINIMUM SIZE:
150 x 150mm, damper up to 250mm high is single blade
construction.
MAXIMUM SIZE:
Dampers
FSD Series
Dimensions
1 - Casing
2 - Blade
3 - Drive Shaft
4 - Face Linkage
5 - Linkage Bar
6 - Landing Angles
8 - Closing Spring
9 - Side Seal
10 - Jack Shaft Device
General
(Flange Type)
2
95
200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
1000
200
250
300
350
400
450
500
600
700
800
900
1000
1
1
2
2
2
3
3
4
4
5
6
6
Supports
& Bands
Number
of Blades
Access
Doors
H
in mm
Flexible
Connectors
W
in mm
Flanges &
Accessories
Standard Sizes
Tapes &
Sealants
Flange Type
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
FSD30 - 100…110…120
Dampers
FSD Series
(Sleeve Type)
General
FSD 40 - 100
Description
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
96
FSD 40 - 110
FRAME:
General construction as type FSD40-100 damper but
steel (Grade 304).
Louvers
BLADES:
Access
Doors
Supports
& Bands
Kitchen
Hoods
FINISH:
Mill galvanized.
LINKAGE:
CASE BEARINGS:
up to 200 ˚C.
FUSIBLE LINK:
FSD 40 - 120
General construction as type FSD40-100 damper but with
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
SEALS:
to close gap between frame & blades.
MINIMUM SIZE:
construction.
MAXIMUM SIZE:
Dampers
FSD Series
Dimensions
1 - Casing
4 - Face Linkage
2 - Blade
5 - Linkage Bar
3 - Drive Shaft/removable spindle when required
6 - Landing Angles
9 - Side Seal
8 - Closing Spring
General
(Sleeve Type)
2
97
200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
1000
200
250
300
350
400
450
500
600
700
800
900
1000
1
1
1
2
3
3
4
4
5
6
6
7
Supports
& Bands
Number
of Blades
Access
Doors
H
in mm
Flexible
Connectors
W
in mm
Flanges &
Accessories
Standard Sizes
Tapes &
Sealants
Sleeve Type
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
FSD40 - 100…110…120
Dampers
FSD Series
General
FSD 50 - 100
Description
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
98
FSD 50 - 110
FRAME (SPIGOT TYPE)
steel (Grade 304).
Louvers
105mmx1.5mm (16 ga) galvanized steel L=530mm
BLADES:
FINISH:
Supports
& Bands
Kitchen
Hoods
Mill galvanized.
LINKAGE:
CASE BEARINGS:
up to 200 ˚C
Access
Doors
FUSIBLE LINK:
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
FSD 50 - 120
SEALS:
MINIMUM SIZE:
250 x 250mm or dia. 200, damper up to 2500mm dia. high
is single blade construction.
MAXIMUM SIZE:
1000 x 1000mm or dia. 1000mm as single section.
Dampers
FSD Series
Dimensions
1 - Casing
2 - Blade
3 - Drive Shaft
4 - Face Linkage
5 - Linkage Bar
6 - Landing Angles
8 - Closing Spring
9 - Side Seal
General
2
99
Number
of Blades
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
1000
1050
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
1000
1050
200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
1000
1
1
2
2
2
3
3
3
4
4
4
5
5
5
6
6
6
Supports
& Bands
"D"
in mm
Access
Doors
H
in mm
Flexible
Connectors
W
in mm
Flanges &
Accessories
Standard Sizes
Tapes &
Sealants
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
FSD40 - 100…110…120
Dampers
FSD Series
(Oval Spigot Type)
General
FSD 60 - 100
Description
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
100
FSD 60 - 110
FRAME (SPIGOT CASE)
steel (Grade 304).
Louvers
BLADES:
FINISH:
Access
Doors
Supports
& Bands
Kitchen
Hoods
Mill galvanized.
LINKAGE:
CASE BEARINGS:
up to 200 ˚C
FUSIBLE LINK:
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
FSD 60 - 120
SEALS:
MINIMUM SIZE:
construction.
MAXIMUM SIZE:
Dampers
FSD Series
Dimensions
1 - Casing
2 - Blade
3 - Drive Shaft
4 - Face Linkage
5 - Linkage Bar
6 - Landing Angles
8 - Closing Spring
9 - Side Seal
General
(Oval Spigot Type)
2
101
Oval Spigot Type
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
1000
1100
200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
1000
1
1
2
2
2
2
3
3
4
4
4
5
5
5
6
6
6
Supports
& Bands
Number
of Blades
Access
Doors
H
in mm
Flexible
Connectors
W
in mm
Flanges &
Accessories
Standard Sizes
Tapes &
Sealants
Oval Spigot Type
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
FSD60 - 100…110…120
Dampers
FSD Series
General
FSD 70 - 100
Description
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
102
FSD 70 - 110
FRAME (SPIGOT CASE)
Louvers
BLADES:
steel (Grade 304).
FINISH:
Kitchen
Hoods
CASE BEARINGS:
Access
Doors
LINKAGE:
Supports
& Bands
Mill galvanized.
Parallel blade have standard face linkage, parallel blade
operation is standard.
up to 200 ˚C.
FUSIBLE LINK:
FSD 70 - 120
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
SEALS:
MINIMUM SIZE:
construction.
MAXIMUM SIZE:
Dampers
FSD Series
Dimensions
1 - Casing
2 - Blade
3 - Drive Shaft
4 - Face Linkage
5 - Linkage Bar
6 - Landing Angles
8 - Closing Spring
9 - Side Seal
General
2
103
200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
1000
200
250
300
350
400
450
500
600
700
800
900
1000
1
1
2
2
2
3
3
4
4
5
6
6
Supports
& Bands
Number
of Blades
Access
Doors
H
in mm
Flexible
Connectors
W
in mm
Flanges &
Accessories
Standard Sizes
Tapes &
Sealants
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
FSD70 - 100…110…120
Dampers
General
Materials Construction
Removable Spindle
Mounting Bracket
Damper with Mounting Bracket for actuator
Blade Seal
Type S1 (Silicone Rubber)
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
104
FSD Series
Note:
Dampers
FSD Series
General
Jack Shaft Device
4- Coil spring
5- Fixed link arm
6- Free link arm
7- Blade Rotation link
8- Fuse link
9- Connecting link arm
10- Shaft joint
11- Drive Spindle
2
105
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
1- Bracket case mounted
2- Shaft bearing
3-Through shaft
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Section of Drive Device
Dampers
General
FSD Series
Flange Installation Details
Flange Type FSD 30
Damper to slide on flange connection
Flange Type FSD 30
Damper to flange connection
Flange drilling details, Type FSD 30
Flange drilling details
W
in mm
H
in mm
No. of Holes
B Dim.
No. of Holes
H Dim.
100
150
200
250
300
350
400
450
500
600
700
800
900
1000
1100
1200
100
150
200
250
300
350
400
450
500
600
700
800
900
1000
1100
1200
1300
1400
1500
1600
1700
1800
1
2
2
2
3
3
4
4
4
5
6
7
8
8
9
10
2
2
2
3
3
4
4
4
5
6
6
7
8
9
10
10
11
12
13
14
14
15
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
106
Dampers
FSD Series
General
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
107
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Kitchen
Hoods
Dampers
General
FSD Series
HEVAC Frame Installation Details
FSD 50
FSD 60
FSD 70
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
108
Dampers
FSD Series
General
Belimo Actuators
S2
S3
BF24 spring return
A03
AF230 spring return
A04
A05
A07
A08
A09
Not applicable
A10
A11
A12
A13
Combination of S1 & S2, fitted
to close gap between frame and
blades and blade edge seals to seal
blade to blade joint. Blade seals is
silicone rubber with temperature
resistance up to 175 ˚C, for ultra
A14
A15
Description
internal face linkage, parallel blade
operation.
A16
A17
SM230A open/closed
A18
SM24A open/closed
A19
A20
NM230 open/closed
A21
NM24 open/closed
A22
NM24 SR Modulating
A23
GM240 open/closed
A24
GM24 open/closed
A25
GM24-SR Modulating
Bearings
B1
Description
Flanges &
Accessories
Construction
Variants
Silencers
A02
2
109
Flexible
Connectors
PB
BF230 spring return
A06
Blade edge seal to seal blades to
blade joint. Blade seal is silicone
rubber with temperature resistance
up to 175 ˚C, for low leakage
characteristic.
Not applicable
Linkage
Construction
Variants
A01
Acoustic
Enclosures
No seals
Not applicable
Type / Model
Plenum
Boxes
S1
Code
Louvers
S
Description
Kitchen
Hoods
Construction
Variants
Supports
& Bands
Seals
Access
Doors
Product Range
oilite (standard).
Stainless steel (optional)
Tapes &
Sealants
B2
Dampers
General
Order Details
Order Code
FSD30-100-PB-S3-B1-R
Variants
*FSD30 = Flange (Standard Supply)
FSD40 = Sleeve
FSD50 = Circular Spigot
FSD60 = Oval Spigot
FSD70 = Rect. Spigot
Type
*100 (std supply)
110
120
Linkage
*PB - Parallel blades
-
500 x 500
-
A 01
Actuators
(See page 97)
Duct Size
Square or rectangular dimension
'W' x 'H' mm circular 'D' mm dia.
Flat oval 'B' x 'H' mm. All dampers
spigots are manufactured down
on duct size to fit inside ductwork
connections.
External Controls
* “R”
“L”
= Left hand
Variants - Bearings
*B1
B2
= Stainless Steel
Variants - Seals
S
= No seal, not applicable for FSD type
S1
= Blade seal only (Not applicable)
S2
= Side seal only (Not applicable)
*S3
= Side & blade seal (175 ˚C), (Standard Supply)
* - Stands for Standard Supply.
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
110
FSD Series
Dampers
Order Example
Combination Fire/Smoke Dampers designed for the
fire/smoke isolation of sections for ducting in ventilation
systems. Basically consisting of a flanged casing, shut
off blades with overlapping interlocking joints, with seals
to close off gap between frame & blades. Blades are
connected by internal linkage for parallel action. Damper
is fitted to internal jack shaft incorporating fusible link
assembly.
STANDARD
Make: SAFID
.
Type : FSD30-100-PB-S3-B1-R-500x500 / A01 .
Qty : 1
.
2
111
Silencers
Specification Text
FSD Series
General
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Manual & electric operation with low leakage blades
construction are available.
Dampers
Smoke Damper
SMD Series
General
(Flange Type)
SMD 30 - 100
Description
Smoke Damper type SMD 30 provide an automatic means
of localizing areas of smoke in ventilation systems. It prevent
the distribution of smoke through ventilation ductworks.
SMD combined with low leakage characteristic for smoke
management, is suitable for installation in sheet metal
brick & lightweight partition walls. SMD is available for
rectangular, square, circular & flat oval duct fixings.
Supports
& Bands
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
112
SMD 30 - 110
FRAME:
General construction as type SMD30-100 damper but
(Grade 304).
180mm x 30mmx1.5mm (16 ga.) galvanized steel,
formed channel for flange connections.
BLADES:
FINISH:
Mill galvanized.
LINKAGE:
Side linkage concealed in frame for parallel blade operation
is standard.
Access
Doors
CASE BEARINGS:
Made of sintered bronze (oilite), operational temp.
resistance up to 200 ˚C
General construction as type SMD30-100 damper but with
Flexible
Connectors
MINIMUM SIZE:
100 x 100mm, damper up to 250mm high are single
blade construction.
MAXIMUM SIZE:
Tapes &
Sealants
Flanges &
Accessories
SMD 30 - 120
Dampers
SMD Series
(Flange Type)
Dimensions
1 - Casing
2 - Blade
3 - Drive Shaft
4 - Side Linkage
Flange Type
7 - Bearing
2
113
Flange Type
SMD30 - 100…110…120
Parallel Blade (PB)
Supports
& Bands
Number
of Blades
1
1
1
1
2
2
2
2
3
3
4
5
5
6
7
7
8
9
9
10
11
12
Access
Doors
H
in mm
100
150
200
250
300
350
400
450
500
600
700
800
900
1000
1100
1200
1300
1400
1500
1600
1700
1800
Flexible
Connectors
W
in mm
100
150
200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
1000
1050
1100
1200
Flanges &
Accessories
Standard Sizes
Tapes &
Sealants
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
SMD30 - 100…110…120
5 - Linkage Bar
6 - Landing angles
General
Smoke Damper
Dampers
Smoke Damper
SMD Series
General
(Sleeve Type)
SMD 40 - 100
Description
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
114
SMD 40 - 110
FRAME:
(Grade 304).
BLADES:
Kitchen
Hoods
FINISH:
Mill galvanized.
Supports
& Bands
LINKAGE:
Face linkage for parallel blade operation is standard.
Face linkage parallel blades available (optional).
Access
Doors
CASE BEARINGS:
resistance up to 200 ˚C
Flanges &
Accessories
Flexible
Connectors
Tapes &
Sealants
SMD 40 - 120
MINIMUM SIZE:
construction.
MAXIMUM SIZE:
Dampers
SMD Series
(Sleeve Type)
Dimensions
1 - Casing
2 - Blade
4 - Side Linkage
5 - Linkage Bar
Sleeve Type
2
115
Sleeve Type
SMD40 - 100…110…120
Parallel Blade (PB)
100
150
200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
1000
1050
1100
1200
1200
100
150
200
250
300
350
400
450
500
600
700
800
900
1000
1100
1200
1300
1400
1500
1600
1700
1800
1
1
1
1
1
2
2
2
2
3
4
4
5
6
6
7
8
8
9
10
11
12
Supports
& Bands
Number
of Blades
Access
Doors
H
in mm
Flexible
Connectors
W
in mm
Flanges &
Accessories
Standard Sizes
Tapes &
Sealants
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
SMD40 - 100…110…120
6 - Landing angles
7 - Bearing
General
Smoke Damper
Dampers
Smoke Damper
SMD Series
General
SMD 50 - 100
Description
Smoke Damper tyoe SMD 50 provide an automatic means
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
116
SMD 50 - 110
FRAME:
(Grade 304).
BLADES:
Kitchen
Hoods
FINISH:
Mill galvanized.
Supports
& Bands
LINKAGE:
Side linkage for parallel blade operation is standard.
Access
Doors
CASE BEARINGS:
resistance up to 200 ˚C.
AXLES & CONTROL SHAFT:
Flanges &
Accessories
Flexible
Connectors
Tapes &
Sealants
SMD 50 - 120
MINIMUM SIZE:
construction.
MAXIMUM SIZE:
Dampers
SMD Series
Dimensions
1 - Casing
2 - Blade
3 - Drive Shaft
4 - Side Linkage
5 - Linkage Bar
6 - Landing angles
7 - Bearing
8 - Spigot case
2
117
SMD50 - 100…110…120
Parallel Blade (PB)
100
150
200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
1000
1050
1100
1150
1200
100
150
200
250
300
350
400
450
500
600
700
800
900
1000
1100
1150
1
1
1
1
2
2
2
2
3
3
4
5
6
6
7
7
Supports
& Bands
Number
of Blades
Access
Doors
H
in mm
Flexible
Connectors
W
in mm
Flanges &
Accessories
Standard Sizes
Tapes &
Sealants
Circular Spigot Type, Parallel Blades
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
SMD50 - 100…110…120
General
Smoke Damper
Dampers
Smoke Damper
SMD Series
General
(Oval Spigot Type)
SMD 60 - 100
Description
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
118
SMD 60 - 110
FRAME:
(Grade 304).
380mm wide with oval spigot duct connection.
BLADES:
Kitchen
Hoods
FINISH:
Mill galvanized.
Supports
& Bands
LINKAGE:
Side linkage for parallel blade operation is standard.
Access
Doors
CASE BEARINGS:
resistance up to 200 ˚C.
AXLES & CONTROL SHAFT:
Flanges &
Accessories
Flexible
Connectors
Tapes &
Sealants
SMD 60 - 120
MINIMUM SIZE:
construction.
MAXIMUM SIZE:
Dampers
SMD Series
(Oval Spigot Type)
Dimensions
1 - Casing
2 - Blade
3 - Drive Shaft
4 - Side Linkage
Oval Spigot Type
5 - Linkage Bar
6 - Landing angles
7 - Bearing
8 - Spigot case
2
119
Oval Spigot Type
SMD60 - 100…110…120
Parallel Blade (PB)
100
150
200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
1000
1050
1100
1150
1200
100
150
200
250
300
350
400
450
500
600
700
800
900
1000
1100
1150
1
1
1
1
2
2
2
2
3
3
4
5
6
6
7
7
Supports
& Bands
Number
of Blades
Access
Doors
H
in mm
Flexible
Connectors
W
in mm
Flanges &
Accessories
Standard Sizes
Tapes &
Sealants
Oval Spigot Type, Parallel Blades
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
SMD60 - 100…110…120
General
Smoke Damper
Dampers
General
Smoke Damper
Removable Spindle
Mounting Bracket
Damper with mounting bracket for actuator
Blade Seal
Type S1 (Silicone Rubber)
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
120
SMD Series
Note:
Dampers
Smoke Damper
SMD Series
Flange type, SMD 30
Damper to slide on flange connection
General
Flange type, SMD 30
Damper to angle flange connection
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
121
100
150
200
250
300
350
400
450
500
600
700
800
900
1000
1100
1200
1300
1400
1500
1600
1700
1800
1
2
2
2
3
3
4
4
4
5
6
7
8
8
9
10
2
2
2
3
3
4
4
4
5
6
6
7
8
9
10
10
11
12
13
14
14
15
Supports
& Bands
100
150
200
250
300
350
400
450
500
600
700
800
900
1000
1100
1200
No. of Holes No. of Holes
W Dim.
H Dim.
Access
Doors
H
in mm
Flexible
Connectors
W
in mm
Flanges &
Accessories
Flange drilling details
Tapes &
Sealants
Flange drilling details, type SMD 30
Kitchen
Hoods
Dampers
General
Smoke Damper
SMD Series
For Sleeve type, SMD 40
Circular Type, SMD 50
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
122
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Oval type SMD 60
Dampers
Smoke Damper
SMD Series
General
Product Range
S3
A02
BF24 spring return
A03
AF230 spring return
A04
Blade edge seal to seal blades to
blade joint. Blade seal is silicone
rubber with temperature resistance
up to 175 ˚C, for low leakage
characteristic.
Not applicable
A05
A06
A07
A08
A09
Not applicable
A10
Combination of S1 & S2, fitted
to close gap between frame and
blades and blade edge seals to seal
blade to blade joint. Blade seals is
silicone rubber with temperature
resistance up to 175 ˚C for ultra
Linkage
Description
PB
A13
A14
A15
A16
A17
SM230A open/closed
A18
SM24A open/closed
A19
A20
NM230 open/closed
A21
NM24 open/closed
A22
NM24 SR Modulating
A23
GM240 open/closed
A24
GM24 open/closed
A25
GM24-SR Modulating
Flexible
Connectors
Construction
Variants
A11
A12
Bearings
Description
oilite.
B2
Stainless steel
Tapes &
Sealants
B1
Flanges &
Accessories
Construction
Variants
2
123
Silencers
BF230 spring return
Acoustic
Enclosures
A01
No seals
Not applicable
Plenum
Boxes
S2
Type / Model
Louvers
S1
Code
Kitchen
Hoods
S
Description
Supports
& Bands
Construction
Variants
Access
Doors
Seals
Dampers
General
Smoke Damper
SMD Series
Order Details
Order Code
SMD30-100-PB-S3-B1-R
Variants-Case
*SMD30 (Standard Supply)
SMD40 = Sleeve
SMD50 = Circular Spigot
SMD60 = Oval Spigot
Type
*100 (std. supply)
110
120
* PB
= Side Linkage Parallel
(Standard Supply)
Face linkage (optional)
-
500 x 500
-
A 01
Duct Size
Actuators
(See page 111)
Flat oval 'B' x 'H' mm.
All damper spigots are manufactured
down on duct size to fit inside ductwork
connections
External Controls
* “R”
“L”
= Left hand
Variants - Bearings
*B1
B2
= Stainless Steel
Variants - Seals
S
= None (Not Applicable)
S1
= Blade seals only (Not Applicable)
S2
= Side seal (Not Applicable)
*S3
= Side seal & blade seals (Standard Supply)
* - Stands for standard supply.
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
2
124
Dampers
SMD Series
Specification Text
Order Example
Rectangular, square, circular & flat oval Smoke Dampers
designed for the smoke isolation of sections of ducting
in ventilation systems. Flanged casing, shut off blades
with overlapping interlocking joints and with side seals
and blade seals for low leakage options (when required).
Blades are connected by side linkage for parallel action &
face linkage parallel action also available.
STANDARD
2
125
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
Make : SAFID
.
Type : SMD 30 - 100 PB - S3 - B1 - R - 500x500 / A01.
Qty : 1
.
General
Smoke Damper
Belimo Damper Actuator
General
Spring-Return Actuator
Open/Close Actuator (230V AC, 24V AC/DC)
BF230-ME, BF24-ME Spring-Return
Mode of operation:
The actuator moves the damper to its normal
working position while tensioning the return
spring at the same time. If the power supply is
interrupted, the energy stored in the spring
moves the damper back to its safe position.
2
126
Plenum
Boxes
Acoustic
Enclosures
Silencers
Manual operation:
Without power supply, the damper can be
operated manually and fixed in any required
position. Release of the locking mechanism
can be achieved manually or automatically by
applying the supply voltage.
Technical Data BF230-ME
Nominal voltage
Louvers
Kitchen
Hoods
Supports
& Bands
Access
Doors
Flexible
Connectors
BF24-ME
Dimensions
AC 230 V, 50/60 Hz AC 24 V, 50/60 Hz /
DC 24 V
Nominal voltage range AC 198 … 264 V
AC 19.2 … 28.8 V /
DC 21.6 … 28.8 V
Power consumption
Monitoring
Holding
For wire sizing
Connecting
Torque
Motor
Spring-return
Running time
Motor
Spring-return
Sound power level
Motor
Spring-return
Position indication
Certification
11 W @ nominal torque 8 W @ nominal torque
3.5 W
12 VA / Imax. 500
2W
11 VA / Imax. 8.3 A
mA @ 5 ms
@ 5 ms
Cable 1 m, 2 x 0.75 mm 2 (halogen-free)
Min. 15 Nm
Min. 15 Nm
<75 s
<20 s (tamb = 20°C)
Wiring Diagram
Max. 45 dB (A)
~62 dB (A)
Mechanical with pointer
cULus according to UL873 and CAN/CSA C22.2 No. 24
Designed to meet UL555S
Certified to IEC/EN 60730-1 and IEC/EN 60730-2-14
Maintenance
Weight
Maintenance-free
Approx. 3.0 kg
2.7 kg
Tapes &
Sealants
Flanges &
Accessories
Code: A1
BF230-S-ME, BF24-S-ME Spring-Return
Mode of operation:
The actuator moves the damper to its normal working
position while tensioning the return spring at the same
time. If the power supply is interrupted, the energy
stored in the spring moves the damper back to its safe
position.
Signalling:
Two microswitches with fixed settings are installed in
the actuator for indicating the damper end positions.
The position of the damper blade can be read off on a
mechanical position indicator.
General
Code: A1S
2
127
Silencers
Spring-Return Actuator
Dimensions
AC 230 V, 50/60 Hz AC 24 V, 50/60 Hz /
DC 24 V
AC 19.2 … 28.8 V /
11 W @ nominal torque 8 W @ nominal torque
2W
11 VA / Imax. 8.3 A
mA @ 5 ms
@ 5 ms
Kitchen
Hoods
3.5 W
12 VA / Imax. 500
Supports
& Bands
2 x SPDT
1 mA…6 A (3 A), DC 5 V …AC 250 V
5o / 80o
Wiring Diagram
Min. 15 Nm
Min. 15 Nm
<75 s
<20 s (tamb = 20°C)
Flexible
Connectors
Auxiliary switch
Contact rating
Switching points
Connecting
Motor
Auxiliary switch
Torque
Motor
Spring-return
Running time
Motor
Spring-return
Sound power level
Motor
Spring-return
Position indication
Certification
Louvers
DC 21.6 … 28.8 V
Power consumption
Monitoring
Holding
For wire sizing
Max. 45 dB (A)
~62 dB (A)
Mechanical with pointer
cULus according to UL873 and CAN/CSA C22.2 No. 24
Designed to meet UL555S
Maintenance-free
Approx. 3.1 kg
Tapes &
Sealants
Certified to IEC/EN 60730-1 and IEC/EN 60730-2-14
Maintenance
Weight
Access
Doors
Nominal voltage
BF24-S-ME
Flanges &
Accessories
Technical Data BF230-S-ME
Plenum
Boxes
Without power supply, the damper can be operated
manually and fixed in any required position. Release of
the locking mechanism can be achieved manually or
automatically by applying the supply voltage.
Acoustic
Enclosures
Manual operation:
2.8 kg
General
Dampers up to approx. 3m2
Code: A01 & A02
BF 230, BF 24 Spring Return
Application:
The type BF… spring return actuator is
intended for the operation of fire & smoke
dampers in ventilation & A/C systems.
2
128
Mode of operation:
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
The BF.. actuator moves the damper to its
normal working position while tensioning the
return spring at the same time. If the power
supply is interrupted, the energy stored in
the spring moves the damper back to its safe
position.
Technical Data
BF 230
BF 24
Power supply
220-240 V AC
50/60 Hz
24V AC (+-) 20%
24V DC (+-) 10%
Power consumption
-monitoring
-holding
8W
3W
7W
2W
For wire sizing
12.5 VA
10 VA
Protection class
II
III
Degree of protection
IP 54
Auxiliary switch
2x SPDT 6(3)A, 250V AC
-Switching points
5˚ , 80˚
Connecting cable
-motor
-auxiliary switches
Angle of rotation
95o (incl. 5 spring pretensioning)
Dimensions
1m, 2x0.75mm2
1m, 6x0.75mm2
Damper rotation
12mm form-fit (10mm with adapter supplied)
Torque
-motor
-spring return
min. 18Nm
min. 12Nm
Running Time
-motor
-spring return
140s
~16s (@ tamb=20˚C)
Direction of rotation
selected by mounting L/R
Position indication
mechanical with pointer
Ambient temp. range
-30…+50 ˚C
Safe temperature
-30…+75 ˚C (24h guaranteed safety)
Non-operating temp.
-40…+80 ˚C
Ambient humidity
class D to DIN 40040
EMC
CE according to 89/336/EEC and 92/31/EEC
Sound power level
motor max. 45 dB (A); spring ~ 62 dB(A)
Service life
min. 60000 safe positions
Maintenance
maintenance-free
Weight
3100 g
Wiring Diagram
2800 g
Open/Close Actuator (230V AC)
Code: A03 & A04
Mode of operation:
2
129
Variable end switch
The AF230-S actuator has one fixed auxiliary
switch & one adjustable auxiliary switch which
allows angle of rotation of 5% & between
26...89% to be signalled.
AF 230
230 V AC, 50/60 Hz
AC198…264 V
Power consumption
-monitoring
-holding
6.5 W
2.5 W
For wire sizing
11 VA
Protection class
II (all insulated)
IP 54
Connecting cable
*AF…-S
Kitchen
Hoods
2x SPDT 6(3)A, 250V AC
fixed 5%
,adjustable 26…89%
-motor
-auxiliary switches
1m, 2x0.75mm2
1m, 6x0.75mm2
Angle of rotation
max. 95˚ (adj. 26…95%
limit stop).
Torque
-motor
min. 15Nm (at rated voltage)
-spring return, min. 15Nm
Running Time
-motor
-spring return
selected by mounting L/R
Position indication
mechanical
Supports
& Bands
-Switching points
with supplied
Wiring Diagram
Flexible
Connectors
150s
16s
Access
Doors
* Auxiliary switch AF..-S
Dimensions
Louvers
Power supply
Nominal voltage range
AF 230-S
Ambient temp. range -30…+50 ˚C
Non-operating temp. -40…+80 ˚C
Ambient humidity
to EN 60335-1
EMC
CE according to 89/336/EEC & 92/31/EEC
Sound power level
motor max. 45 dB (A); spring
Service life
min. 60000 operations
Maintenance
maintenance-free
Weight
3300 g
Tapes &
Sealants
62 dB(A)
Flanges &
Accessories
Technical Data
Acoustic
Enclosures
The AF.. actuator moves the damper to its
normal working position while tensioning the
return spring at the same time. If the ower supply
is interrupted, the energy stored in the spring
Plenum
Boxes
The type AF… spring return actuator are
intended for the operation of air dampers that
perform safety functions (e.g. frost & smoke
protection, hygiene, etc.).
Silencers
Application:
General
AF 230, AF 230-S (Spring Return)
* Switch applies for model AF 230-S
General
Open/Close Actuator (230V AC, 120V AC)
AF 230, AF 120 US (Spring Return)
Application:
For on-off, fail-safe control of dampers in
HVAC systems.
Actuator sizing should be done in accordance
with the damper manufacturer's specs. Control
is on-off from an auxillary contact, or a manual
switch.
2
130
Silencers
Mode of operation:
The AF series actuators provide true spring
return operation for reliable fail-safe application
& positive close off on air tight dampers. The
spring return system provide consistent torque
to the damper with and without power applied
to the actuator.
Acoustic
Enclosures
Plenum
Boxes
Louvers
Code: A05 & A06
Technical Data
AF 230 US
AF 120 US
Power supply
230 VAC (+-) 14%
50/60Hz
120 VAC (+-) 10%
Power consumption
running : 6.5W
holding : 2.5W
6W
2.3W
Transformer sizing
11 VA
10 VA
Dimensions
Access
Doors
Supports
& Bands
Kitchen
Hoods
Electrical connection 3 ft, 18 GA appliance cable 1/2" conduit
connection.
Overload protection
electronic throughout 0 to 95˚ rotation.
Angle rotation
95˚, adjustable 30 to 95o w/ accessories
Torque
133 in-lb [15Nm] constant
spring return can be selected by L/R
mounting
Position indication
visual indicator, -5˚ to 90˚ (-5˚ is spring
return position).
Manual override
3mm hex crank (shipped w/ actuator)
Running Time
150 sec. constant, independent of load,
spring return < 20 sec
Humidity
5 to 95% RH noncondensing
Wiring Diagram
Storage temperature -40 ˚F to 175 ˚F [-40 ˚C to 80 ˚C]
Housing
NEMA type 2 / IP54
Housing material
Zinc coated steel
Agency listings
UL 873 listed, CSA 4813 02 certified
Noise level
max. 45 dB (A)
Servicing
Maintenance free
Quality standard
ISO 9001
Weight
6.9 lbs (3.1 kg.)
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Ambient temperature -22 ˚F to 122 ˚F [-30 ˚C to +50 ˚C]
For on-off, fail-safe control of dampers in HVAC
systems. Actuator sizing should be done in
accordance with the damper manufacturer's
specs. Control is on-off from an auxillary contact,
or a manual switch.
Mode of operation:
to the damper with and without power applied to
the actuator.
The AF...-S us is provided with 2 built in auxiliary
switches. The SPDT switches are provided for
safety interfacing or signalling, for ex. for fan
start up.
Technical Data AF 230-S US AF 120-S US
230 VAC (+-) 14%
50/60Hz
120VAC (+-) 10%
Power consumption
running : 6.5W
holding : 2.5W
6W
2.3W
Transformer sizing
11 VA
10 VA
Louvers
Power supply
Dimensions
2
131
Silencers
Application:
Acoustic
Enclosures
AF 230-S, AF 120-S US (Spring Return)
General
Code: A07 & A08
Plenum
Boxes
Open/Close Actuator (230V AC, 120V AC)
Angle rotation
95˚, adjustable 30 to 95˚ w/ accessories
Torque
mounting
Position indication
return position).
Manual override
Auxiliary switches
2xSPDT 7A (2.5A) @ 250 VAC, UL listed
AF…-S
one set at +5˚, one adjustable 25˚ to 85˚.
Running Time
Humidity
Flexible
Connectors
Wiring Diagram
Zinc coated steel
Agency listings
Noise level
max. 45 dB (A)
Servicing
Maintenance free
Quality standard
ISO 9001
Weight
6.9 lbs (3.1 kg.)
Tapes &
Sealants
NEMA type 2 / IP54
Housing material
Flanges &
Accessories
Housing
Access
Doors
Supports
& Bands
Overload protection
Kitchen
Hoods
connection.
General
Open/Close Actuator (24V)
Code: A09
AF 24 US (Spring Return)
Application:
systems.
switch.
2
132
Silencers
Mode of operation:
Louvers
Plenum
Boxes
Acoustic
Enclosures
the actuator.
Technical Data
Dimensions
Power supply
24 VAC (+-) 20%, 50/60Hz
24 VDC (+-) 10%
Power consumption
running : 5W
holding : 1.5W
Transformer sizing
10 VA (class 2 power source)
Overload protection
Angle rotation
Torque
mounting
Position indication
return position).
Manual override
Running Time
Humidity
Ambient temperature
-22 ˚F to 122 ˚F [-30 ˚C to +50 ˚C]
Storage temperature
-40 ˚F to 176 ˚F [-40 ˚C to 80 ˚C]
Housing
NEMA type 2 / IP54
Housing material
Zinc coated steel
Agency listings
Noise level
max. 45 dB (A)
Servicing
Maintenance free
Quality standard
ISO 9001
Weight
6.0 lbs (2.7 kg.)
Wiring Diagram
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Kitchen
Hoods
connection.
specs. Control is on-off from an auxillary
contact, or a manual switch.
Mode of operation:
the actuator.
The AF120-S us is provided with 2 built in
auxiliary switches. The SPDT switches are
provided for safety interfacing or signalling, for
ex. for fan start up.
Technical Data
Power supply
24 VAC (+-) 20%, 50/60Hz
24 VDC (+-) 10%
Power consumption
running : 5W
holding : 1.5W
Transformer sizing
Louvers
Dimensions
2
133
Silencers
Application:
Acoustic
Enclosures
AF 24-S US (Spring Return)
General
Code: A10
Plenum
Boxes
connection.
mounting
Position indication
return position).
Manual override
Supports
& Bands
Torque
one set at +5˚, one adjustable 25˚ to 85˚.
Running Time
Humidity
-40 ˚F to 176 ˚F [-40 ˚C to 80 ˚C]
NEMA type 2 / IP54
Zinc coated steel
Agency listings
Noise level
max. 45 dB (A)
Servicing
Maintenance free
Quality standard
ISO 9001
Weight
6.0 lbs (2.7 kg.)
Tapes &
Sealants
Housing
Housing material
Flanges &
Accessories
-22 ˚F to 122 ˚F [-30 ˚C to +50 ˚C]
Storage temperature
Wiring Diagram
Flexible
Connectors
Auxiliary switches
AF24S
Ambient temperature
Kitchen
Hoods
Access
Doors
Overload protection
Angle rotation
General
Modulating Actuator (24V)
Code: A11
AF 24-SR (Spring Return)
Control DC0...10V or 0...20V phasecut
Position feedback DC2...10V
Manual operation with integral position stop
Application:
2
134
For the operation of air dampers that perform safety
functions (e.g. frost & smoke protection, hygiene)
Mode of operation:
Silencers
The AF24-SR actuator moves the damper to
its normal working position while tensioning the
return spring at the same time. If the power supply
is interrupted, the energy stored in the spring
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Variable end switch
AF230-S actuator has one fixed auxiliary switch &
one adjustable auxiliary switch whic allows angle of
rotation of 5% & between 26...89% to be signalled.
Technical Data
Power supply
AC 24 V, 50/60 Hz
AC19.2…28.8 V
Power consumption
monitoring 6W
holding 2.5W
For wire sizing
10 VA
Protection class
III (safety extra-low voltage)
IP 54
Connecting cable
-motor
Control signal Y1
DC0…10V @ input resistance 100kΩ (0.1mA)
Operating range
DC2…10V (at control signal Y1)
2…10V phasecut (at control signal Y2)
Control signal Y2
Supports
& Bands
Dimensions
1m, 5x0.75mm2
0…20V phasecut @ input resistance 8kΩ (50mW)
Measuring voltage U DC2…10V @ max.0.5mA (for 0..100%
angle of rotation).
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Synchronisation tolerance (+-) 5%
Wiring Diagram
motor selected with switch L/R
spring selected by L/R mounting
Torque
-motor
-spring return, min. 15Nm
Angle of rotation
max. 95˚ (adj. 26…95% < with supplied
limit stop).
Running Time
-motor 150s, spring return ~15s
Sound power level
motor max. 45 dB (A); spring ~ 62 dB(A)
Service life
min. 60000 operations
Position indication
mechanical
Ambient humidity
to EN 60335-1
EMC
Maintenance
maintenance-free
Weight
3180 g :
AF230S = 3370 g
For on-off, fail-safe control of dampers in
HVAC systems.
switch.
Mode of operation:
The NF series actuators provide true spring
to the damper with and without power applied
to the actuator.
Technical Data NF 24 US
NF 120 US
Dimensions
24 VAC (+-) 20%
24 VDC (+-) 10%
120V AC (+-) 10%
50/60Hz
Power consumption
running : 5W
holding : 2.6W
6W
3.5W
Transformer sizing
2 VA
7VA
Louvers
Power supply
2
135
Silencers
Application:
Acoustic
Enclosures
NF 24, NF 120 US (Spring Return)
General
Code: A12 & 13
Plenum
Boxes
Dampers up to approx. 1.5m2
Open/Close Actuator (24V, 120C AC)
connection.
60 in-lb [7Nm] constant torque
mounting
Position indication
visual indicator, -5˚ to 95˚ (0˚ is spring
return position).
Running Time
motor: < 75 sec
Humidity
Supports
& Bands
Torque
Kitchen
Hoods
Wiring Diagram
Access
Doors
Overload protection
Angle rotation
Housing
NEMA type 2 / IP54
Zinc coated steel
UL 873 listed, CSA 4813 02 certified,CE
Noise level
max. 45 dB (A)
Maintenance free
Quality standard
ISO 9001
Weight
6.6 lbs (3.0 kg.)
7.3 lbs (3.3 kg)
Tapes &
Sealants
Servicing
Flanges &
Accessories
Housing material
Agency listings
Flexible
Connectors
General
Open/Close Actuator (24V, 120C AC)
NF 24-S, NF 120-S US (Spring Return)
Application:
specs. Control is on-off from an auxillary contact,
or a manual switch.
2
136
Mode of operation:
Silencers
The NF series actuators provide true spring return
operation for reliable fail-safe application & positive
close off on air tight dampers. The spring return
system provide consistent torque to the damper
with and without power applied to the actuator.
The NF...-S us is provided with 1 built in auxiliary
switches. The SPDT switches are provided for
safety interfacing or signaling, for ex. for fan start
up.
Acoustic
Enclosures
Plenum
Boxes
Louvers
Code: A14 & 15
Technical Data NF 24-S US NF 120-S US
Power supply
24 VAC (+-) 20%
24 VDC (+-) 10%
120VAC (+-) 10%
50/60Hz
Power consumption
running : 5W
holding : 2.6W
6W
3.5W
Transformer sizing
2 VA
7VA
Dimensions
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Kitchen
Hoods
connection.
Overload protection
Angle rotation
Torque
mounting
Position indication
return position).
Auxiliary switches
NF...-S
adjustable 5˚ to 85˚.
Running Time
motor: < 75 sec
Humidity
Ambient temperature
-22 ˚F to 122 ˚F [-30 ˚C to +50 ˚C]
Storage temperature
-40 ˚F to 176 ˚F [-40 ˚C to 80 ˚C]
Housing
NEMA type 2 / IP54
Housing material
Zinc coated steel
Agency listings
Noise level
max. 45 dB (A)
Servicing
Maintenance free
Quality standard
ISO 9001
Weight
6.6 lbs (3.0 kg.)
Wiring Diagram
7.3 lbs (3.3 kg)
Application:
specs.
Mode of operation:
The NF series actuators provide true spring return
operation for reliable fail-safe application & positive
close off on air tight dampers. The spring return
system provide consistent torque to the damper with
and without power applied to the actuator.
Technical Data
Power supply
24 VAC (+-) 20%, 50/60Hz
24 VDC (+-) 10%
Power consumption
running : 3W
holding : 1W
Transformer sizing
Louvers
Dimensions
2
137
Silencers
Proportional damper actuator, 24V for 0
to 10VDC, or to 10 mA control signal.
Output signal of 2 to 10 VDC for position
indicator.
Acoustic
Enclosures
NF 24-SR US (Spring Return)
General
Code: A16
Plenum
Boxes
connection.
Kitchen
Hoods
Y1 0 to 10 VDC, 0 to 20 mA
Imput impedance
100 kW (0.1 mA), 500W
Operating range
2 to 10 VDC, 4 to 20 mA
Supports
& Bands
Feedback output “U” 2 to 10 VDC (max. 0.5 mA) for 95˚
95˚, adjustable 30 to 95˚ w/ accessory
Torque
spring return selected by L/R mounting
control direction selected by L/R switch
Position indication
return position).
Running Time
motor: 150 sec constant independent
of load
Humidity
Wiring Diagram
Flexible
Connectors
Angle rotation
Access
Doors
Control signal
NEMA type 2 / IP54
Zinc coated steel
Agency listings
Noise level
max. 45 dB (A)
Servicing
Maintenance free
Quality standard
Weight
ISO 9001
6.0 lbs (2.7 kg.)
Tapes &
Sealants
Housing
Housing material
Flanges &
Accessories
Overload protection
Code: A17 & 18
SM230A, SM24A Open/Close
Control:
Open-close or 3-point
Application:
The actuator is overload-proof, requires no
limith switches and automatically stops when
the end stop is reached.
Mode of operation:
Manual operation is possible with the selfresetting pushbutton (the gearing latch remains
disengaged as long as the pushbutton is
pressed).
Acoustic
Enclosures
2
138
Silencers
General
Power supply
230 V AC
50/60Hz
Nominal voltage range AC 85…265 V
SM24A
Dimensions
24V AC/DC
AC/DC 19.2…28.8V
Power consumption
In operation
2.5 @ nominal torque 2 W @ nominal torque
At rest
For wire sizing
0.6 W
6 VA
Connection
cable 1 m, 3 x 0.75 mm 2
reversible with switch 0
Torque
Angle of rotation
min. 20Nm @ nominal voltage
max. 95o , limited on both sides
or 1
by means of adjustable, mechanical end stops
Running time
150 s
Sound power level
Position indication
max. 45 dB (A)
mechanical, pluggable
Protection class
II totally insulated
Wiring Diagram
Protection class (SM24A) III safety extra-low voltage
Degree of protection IP54 in any mounting position
o
Ambient temp. range -30…+50 C
o
Non-operating temp. -40…+80 C
Ambient humidity
95% r.H., non-condensating (EN 60730-1)
EMC
Maintenance
CE according to 89/336/EEC
maintenance-free
Weight
approx. 1050 g
1000 g
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Access
Doors
Supports
& Bands
Kitchen
Hoods
Louvers
Plenum
Boxes
Technical Data SM230A,
Application:
The actuator is overload-proof, requires no
limith switches and automatically stops when
the end stop is reached.
Mode of operation:
Manual operation is possible with the selfresetting pushbutton (the gearing latch remains
disengaged as long as the pushbutton is
pressed).
Flexible signalization with adjustable auxilliary
switch (0 ... 100%).
230 V AC
50/60Hz
Nominal voltage range AC 85…265 V
24V AC/DC
AC/DC 19.2…28.8V
In operation
2.5 @ nominal torque 2 W @ nominal torque
At rest
For wire sizing
0.6 W
6 VA
Kitchen
Hoods
1 x SPDT, 1 mA … 3 (0.5) A, AC 250 V
(0 … 100% adjustable)
Auxilliary switch
cable 1 m, 3 x 0.75 mm 2
cable 1 m, 3 x 0.75 mm 2
reversible with switch 0
Torque
Angle of rotation
max. 95o , limited on both sides
Supports
& Bands
Connection
Motor
or 1
Running time
150 s
Sound power level
Position indication
max. 45 dB (A)
Protection class
Wiring Diagram
Flexible
Connectors
Access
Doors
Auxilliary switch
Louvers
Power consumption
Protection class (SM24A-S III safety extra-low voltage
o
o
Ambient humidity
EMC
Maintenance
maintenance-free
Weight
approx. 1100 g
Tapes &
Sealants
1050 g
Flanges &
Accessories
Power supply
Dimensions
Plenum
Boxes
Technical Data SM230A-S, SM24A-S
2
139
Silencers
Control:
Open-close or 3-point
Integrated auxilliary switch
Acoustic
Enclosures
SM230A-S, SM24A-S Open/Close
General
Code: A17.1 & 18.1
General
Modulating Actuator (230V AC)
Code: A19
SM230ASR (Modulating)
Control:
DC 0...10 V, position feedback DC 2...10 V6.
Application:
The actuator is overload-proof, requires no limith
switches and automatically stops when the end stop is
reached.
Silencers
Manual operation is possible with the self-resetting
pushbutton (the gearing latch remains disengaged as
long as the pushbutton is pressed).
Louvers
Plenum
Boxes
Mode of operation:
The actuator is controlled by means of a standard
control signal DC 0...10 V. It opens to the position
dictated by this signal. The measuring voltage U allows
the damper position (0...100%) to be electrically
indicated and serves as a follow-up control signal for
other actuators.
Acoustic
Enclosures
2
140
Technical Data SM230ASR
Power supply
Dimensions
AC 100 … 230 V, 50/60 Hz
Power consumption
In operation
3.5 @ nominal torque
At rest
1W
For wire sizing
6.5 VA
Power supply
cable 1 m, 2 x 0.75 mm 2
Signals
cable 1 m, 4 x 0.75 mm 2
Control signal Y
Working range
DC 0 …10 V, typical input impedance 100 kΩ
DC 2 …10 V
Positioning accuracy ±5%
(at Y=0 V)
Torque
at switch position 0
resp. 1
Angle of rotation
max. 95o
Wiring Diagram
, limited on both sides
Protection class
Flexible
Connectors
150 s
max. 45 dB (A)
Position indication
Flanges &
Accessories
Running Time
Sound power level
o
Ambient humidity
EMC
Maintenance
maintenance-free
Tapes &
Sealants
Access
Doors
Supports
& Bands
Kitchen
Hoods
Connection
Weight
approx. 1200 g
o
Application:
The damper actuator has no limit switches and
is overload-proof. It stops automatically when it
reaches the damper or actuator end stop.
Mode of operation:
A functional check of damper operation is simplicity
itself: the gearing can be disengaged by simply
pressing a pushbutton on top of th case. While
the pushbutton remains depressed, the damper
can be operated by hand.
24V AC/DC
AC198…264 V
AC/DC19.2…28.8V
For wire sizing
18 VA
3.5VA
Power consumption
2W
2W
Connecting cable
1m long, 3x0.75mm2
selected with L/R switch
Torque
Angle of rotation
max 95˚ (adjustable by mechanical stops)
Running Time
75…150s (0…8Nm)
Sound power level
max. 35 dB (A)
Position indication
mechanical
Protection class
II (all insulated)
IP 54 (cable entry down)
Kitchen
Hoods
230 V AC
50/60Hz
Louvers
Dimensions
Supports
& Bands
Power supply
NM 24
III (safety low voltage)
Wiring Diagram
to EN 60335-1
EMC
Maintenance
maintenance-free
Weight
800 g
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Ambient humidity
Access
Doors
Technical Data NM 230
2
141
Silencers
NM230, Control by single-pole contact
(single wire control)
NM24, Reversible
Acoustic
Enclosures
NM 230, NM 24 (Open / Close)
General
Code: A20 & 21
Plenum
Boxes
General
Modulating Actuator (AC 24V)
Code: A22
NM 24-SR (Modulating)
Control DC0...10V & position feedback DC2...10V
Self-adapting, automatic angle of rotation and
running time adjustment.
Application:
2
142
The damper actuator has no limit switches and is
overload-proof. It stops automatically when it reaches
the damper or actuator end stop.
Silencers
Mode of operation:
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
When the power supply is first switched on, or when the
override push button is pressed the actuator actuator
performs an automatic function test.
pressing a pushbutton on top of th case. While the
pushbutton remains depressed, the damper can be
operated by hand.
Technical Data
Dimensions
Power supply
AC 24 V AC 50/60 Hz
AC/DC 19.2…28.8 V
For wire sizing
3 VA
Power consumption
1.3 W running, 0.5 W at rest
Connecting cable
1m long, 4x0.75mm2
Control signal Y
DC0…10 V input resistance 100kΩ
Operating range
DC2…10V (for 0…100% angle of rotation)
Measuring voltage U DC2…10V @ <0.7 mA (for 0…100%
angle of rotation)
(at Y=0 V)
selected with L/R switch
at switch position L
resp. R
max. 95˚ (adjustable by mechanical stops)
Running Time
150s, regardless of the mechanically
limited angle of rotation from 0…35˚
< to 0…95˚ <
Sound power level
max. 35 dB (A)
Position indication
mechanical
Protection class
Tapes &
Sealants
Access
Doors
Torque
Angle of rotation
Flexible
Connectors
Y open or 0 V = 0% angle of rotation
Y at AC24 V = 100% angle of rotation
Flanges &
Accessories
Supports
& Bands
Synchronisation tolerance (+-) 5%
Override control
Wiring Diagram
Ambient humidity
to EN 60335-1
EMC
Maintenance
maintenance-free
Weight
900 g
Application:
Mode of operation:
Technical Data
AC198…264 V
For wire sizing
10 VA @ 50Hz, 13VA @ 60Hz
Power consumption
10 W @ 50Hz, 13W @ 60Hz
Connecting cable
0.9m long, 4x0.75mm2
reversible with switch A/B
Torque
Angle of rotation
mechanically limited to 95˚
Running Time
~ 180 s
Sound power level
max. 45 dB (A)
Position indication
0…10 (0=stop
Protection class
I (with PE conductor)
Kitchen
Hoods
230 V AC, 50/60 Hz
Supports
& Bands
)and reversible indicator
Wiring Diagram
to EN 60335-1
EMC
Maintenance
maintenance-free
Weight
2000g
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Ambient humidity
Access
Doors
Power supply
Louvers
Dimensions
2
143
Silencers
2-Wire Control
Acoustic
Enclosures
GM 240 (Open / Close)
General
Code: A23
Plenum
Boxes
Open/Close Actuator (230V AC)
General
Open/Close Actuator (AC/DC 24V)
GM 24 (Open / Close)
Reversible
Application:
2
144
Mode of operation:
Supports
& Bands
Kitchen
Hoods
Louvers
Plenum
Boxes
Acoustic
Enclosures
Silencers
Technical Data
Dimensions
Power supply
AC 24 V , 50/60 Hz, DC 24 V
AC19.2…28.8 V, DC 21.6…26.4 V
For wire sizing
6 VA
Power consumption
3 W running, 1 W at the end position
Connecting cable
0.9m long, 3x0.75mm2
Torque
Angle of rotation
Running Time
~ 135 s (+-) 15 s
Sound power level
max. 45 dB (A)
Position indication
0…10 (0=stop
Protection class
)and reversible indicator
Access
Doors
Wiring Diagram
Ambient humidity
to EN 60335-1
EMC
Maintenance
maintenance-free
Weight
2000g
Tapes &
Sealants
Flanges &
Accessories
Flexible
Connectors
Code: A24
Modulating Actuator (AC 24V)
Mode of operation:
Technical Data
Dimensions
AC 24 V AC 50/60 Hz
AC/DC 19.2…28.8 V
For wire sizing
7 VA
Power consumption
3 W running, 2 W at rest
Connecting cable
0.9m long, 5 x 0.75mm2
Control signal Y1
DC 0…10 V input resistance 100kΩ (0.1mA)
DC2…10V (at control signal Y1)
2…10V phasecut (at control signal Y2)
Kitchen
Hoods
Operating range
Synchronisation tolerance
(+-) 5%
(at Y=0 V)
at switch position A
resp. B
Torque
Angle of rotation
Running Time
~ 135 s (+-) 15 s
Sound power level
max. 45 dB (A)
Position indication
0…10 (0=stop
Protection class
Supports
& Bands
Measuring voltage U DC2…10V @ max.0.5mA(for 0…100%
angle of rotation)
Wiring Diagram
) and reversible indicator
Access
Doors
0…20 V phasecut @ input resistance
8 k (50 mW)
Flexible
Connectors
Control signal Y2
Louvers
Power supply
2
145
Silencers
Application:
Acoustic
Enclosures
Control DC 0...10 V or 0...20 V phasecut
Position feedback DC 2...10 V
Plenum
Boxes
GM 24-SR (Modulating)
General
Code: A25
to EN 60335-1
EMC
Maintenance
maintenance-free
Weight
2000 g
Tapes &
Sealants
Ambient humidity
Flanges &
Accessories

1 SPK 100 Series 1-15

Transcription

Similar documents

to the Zeroshift Electric Vehicle Transmissions brochure

Fitting a Steering Damper to your Morgan

Untitled - Bron

GEISLINGER DAMPER

Damper Comparison

to learn more about the Lyemance top sealing damper.

Quick Blade - Draco Equipment

CHOPMASTER - Forrest Saw Blades

Paul Strisik NA - American Fine Art Magazine

de Carbon Performance