NO MORE COLD FEET

Transcription

NO MORE COLD FEET

Insulate professionally. Profit long-term.
EN
N O MO RE C O LD F E E T
Quality Of Life Can Be Planned
1
2
EXPERIENCE THE WARMEST
MOMENTS WITH thermotec®
No more cold feet! That's more than just empty
words for us at thermotec®. It's a value proposition fastidiously guaranteed. Why? Because
floors insulated with thermotec® are simply
warmer for your feet. You can feel this with
the very first contact. Whether in the morning
when getting up, after a shower in the bath-
room, while sitting at a desk or a cozy evening
on the couch, heat is always flowing over your
feet and into the floor.
With thermotec®, you can reduce this heat
loss significantly. So you save valuable energy
while increasing comfort.
3
IN LIFE THERE ARE INTRINSIC INNER VALUES,
WHICH ALSO NEED TO BE AFFORDABLE.
Quality of life can be planned.
With thermotec® on the floor it becomes a reality.
The fact is that we at thermotec®
apply only half as thick a layer to
achieve acceptable insulation values.
This means for you as a planning architect: You achieve sufficient heat
protection even with low installation
heights!
4
The fact is that with thermotec®, you
get impact sound insulation, leveling
and thermal insulation in one go. You
save important working hours, achieve
a readiness for covering faster and have
all the temperature control of all floor
areas. A balance that you can really
feel. With thermotec® the floors become
a piece of adorable and comfortable living space.
No more cold feet.
A promise is a promise!
COMPARATIVE MEASUREMENT IN TWO PATTERN FLOOR STRUCTURES
Measured U-value: 0,988 m2K/W
Product: 50 mm EPS-W20 WLG 038
Unevenness is compensated in the screed. Pipes are exposed.
Does not correspond to DIN 18560-2 and the NORM B 2232.
Measured U-value: 0,818 m2K/W
Product: 50 mm thermotec® BEPS-WD 100R WLG 050
Unevenness is compensated in the damp course (no excess consumption with screed!).
Pipes are well-covered. Jointless installation. No clippings and no waste.
20% less heat loss. Base layer conforms to norms! NORMS CHECKED!
Schematic comparison of thermotec® – Polystyrene concrete
Polystyrene concrete
thermotec®
Thanks to the thin binder film, thermotec® achieves insulation values similar to polystyrene.
Polystyrene concrete offers through the dense cement microstructure little insulation properties.
Polystyrene concrete needs about twice the mounting
strength to reach the insulation values of thermotec®.
5
WHETHER FLOOR, WALL, CEILING OR ROOF –
THERMOTEC®-PRODUCTS ARE VERSATILE IN APPLI
1
2
3
6
Attic insulation
thermotec® Insulation Filler is used for
loft insulations. The jointless insulation
material can be used without screed if
the insulated surface is not going to be
walked upon.
Pitched roof insulation
thermotec® Insulaion Fillers are blown
and without joins under pressure inbetween the rafters.
Wall backfill
The thermotec® Insulation Filler is
injected into the cavities with compressed air.
4
Insulation under flowing screed
thermotec® Insulation Fillers insulate
and pave the underground under flowing screeds in an ideal way. Thus material consumption is lowered for the
leveling screed.
5
Insulation under heated screed
thermotec® Insulation Fillers are suitable for installation under floor heating.
6
Insulation under Nano Screed®
thermotec® Insulation Fillers can be
used under the Nano Screed® in all living areas.
7
Insulation under pre-fab screed
The more solid thermotec® products
are also suitable as sub-construction
for pre-fab (dry) screeds.
8
Arch/vault backfilling
Arche/vault backfilling and height
backfilling can be designed/created
with thermotec®-Insulation Fillers up
to a meter in one work process.
9
Cellar backfill
Thermal insulation, protection of the
basement wall waterproofing, backfill,
drain layer and substructure for plaster
eaves in one work process.
1
2
2
3
6
5
3
4
12
14
8
14
7
15
9
11
11
13
9
10
CATION
10
Insulation under the cement screed
thermotec® Insulation Fillers under
cement screeds in all areas of the living space of a building.
11
Insulation under mastic asphalt
screed
thermotec® Insulation Fillers can be
used under mastic asphalt screeds.
Fesco slates should be laid before the
laying of mastic asphalt screed.
12
13
Flat roof slope insulation
You can make the slope in and apply
the necessary insulation in one work
process. No more long planning and
delivery times.
Slab floor insulation
With the thermotec® Slab Floor Insulation Filler, you can create a flat
granular subbase and at the same
time provide the necessary thermal
insulation in one work process.
14
15
Pool backfill
pooltec-Wall insulates and backfills
your swimming pool. As a result,
the average water temperature is increased by about 4°C.
Pool slab floor insulation
pooltec-Floor creates a flat, heat-insulating underground for your swimming pool.
7
E-46-45-200-45
Combined heat and footfall sound-absorbing compensation material
for normal loads under flowing and cement screed
BEPS-T ÖNORM B 6550-1-PS(0-8)R-LD80-FMD124-DMD98-MU6-CC(2,0/1,5/10)10-SD40-CP5
Technical data
8
Sack contents
200 litres (14,9 - 17,1 kg)
Sack per pallet
16 units (3,2 m³)
Fire behaviour acc. OENORM B 3800 Part 1
B1/TR1/Q1
Fire behaviour acc. EURO CLASS
E
Fire behaviour acc. DIN 4102 Part 1
B2
Nominal Value of thermal conductivity λD
0,046 W/mK
Min. layer thickness
45 mm
Max. layer thickness
(for details request application table)
200 mm (superficial load 2 kN/m2)
100 mm (superficial load 3,5 kN/m2)***
Water admixture for every m3
45 litres
Grain group of the EPS-aggregate
0-8R
Registration
Number
ON-N 2008 159
EUROPEAN ORGANISATION
FOR TECHNICAL APPROVAL
European Technical Approval ETA-08/0338
PS
Bulk density of the EPS-dry mortar
80 kg/m
LD
Fresh mortar density
124 kg/m3
FMD
Dry bulk
98 kg/m
DMD
Water vapour diffusion resistance factor
≤ 6μ
MU
Creep characteristic 10 years at
Total compressive strain
Creep deformation
10 kPa
≤ 2,0%
≤ 1,5%
CC
Dynamic stiffness s´
(at 45 mm thickness)
≤ 40 MN/m3
SD
Compressibility c
≤ 5 mm
CP
Water absorption
with momentary, partial dunking
≤ 3,0 kg/m2
Processing time (open time, 20˚/60% LF)
Min. 45 min.
Processing temperature min./max.
+5o /+35o C
Hard enough to walk on after
Ca. 2 days*
Ready for covering from (CM-measurement)
with a layer thickness up to 50 mm
≤ 12 M-%
Ca. 2 days**
Ca. 4 days**
Ca. 7 days**
Footfall/impact sound improvement
at 70 mm thickness and 100 kg of screed
28 dB (solid floors/ceilings)
25 dB (solid floors/ceilings)
3
3
Finished product
Free bare floor/ceiling
* Dependent on temperature and air moisture.
** The information is to be understood as approximate values.
A CM-measurement is required.
*** Higher installation thicknesses on request.
E-48-30-800-45
Combined heat-absorbing equalising material
for normal loads under flowing and cement screed
BEPS-ÖNORM 6550-1-PS(0-8)R-LD82-FMD130-DMD102-MU6-CS(10)50-CC(2,5/1,5/10)10-DLT(1)5
Technical data
Sack contents
200 litres (14,8 - 18,0 kg)
Sack per pallet
16 units (3,2 m³)
B1/TR1/Q1
E
B2
0,048 W/mK
30 mm
500 mm (superficial load 3,5 kN/m2)
45 litres
0-8R
Registration
Number
ON-N 2008 011
PS
LD
82 kg/m
130 kg/m3
FMD
Dry bulk
102 kg/m
DMD
≤ 6μ
MU
3
3
Compressive stress at 10% deformation
≥ 50 kPa
CS (10)
25 kPa
CS (2)
Creep deformation
10 kPa
≤ 2,5%
≤ 1,5%
CC
Dimensional stability in pressure and
temperature stress
≤ 5%
DLT (1)
Water absorption
≤ 2,0 kg/m2
Min. 60 min.
+5o /+35o C
Ca. 2 days*
with a layer thickness up to 50 mm (23ºC/50% LF)
≤ 12 M-%
Ca. 3 days**
Ca. 7 days**
Ca. 10 days**
28 dB (60 mm installation thickness +
5 mm thermotec® acoustic system rail)
Finished product
** The information is to be understood as approximate values.
A CM-measurement is required.
9
E-50-20-2000-50
Combined heat-absorbing equalising material
for heavy loads under flowing and cement screed and
for normal loads under precast(dry)and mastic asphalt screed
BEPS-ÖNORM 6550-1-PS(0-8)R-LD110-FMD160-DMD130-MU6-CS(10)70-CC(2,5/2,3/10)20-DLT(1)5
Technical data
Sack contents
200 litres (19,8 - 24,2 kg)
Sack per pallet
16 units (3,2 m³)
B1/TR1/Q1
E
B2
0,050 W/mK
20 mm
Registration
Number
ON-N 2008 012
On request (depending on screed
thickness and quality):
50 litres
0-8R
110 kg/m
LD
3
160 kg/m
FMD
Dry bulk
130 kg/m3
DMD
≤ 6μ
MU
≥ 70 kPa
CS (10)
35 kPa
CS (2)
Creep deformation
10 kPa
≤ 1,9%
≤ 0,8%
temperature stress
≤ 5%
Water absorption
≤ 2,0 kg/m2
Min. 60 min.
+5o /+35o C
Ca. 2 days*
≤ 12 M-%
Ca. 2 days**
Ca. 5 days**
Ca. 8 days**
PS
3
20 kPa
≤ 2,5%
≤ 2,3%
** The information is to be understood as approximate values. A CM-measurement is required.
10
CC
Finished product
DLT (1)
E-43-30-2000-25
Combined quick-drying and heat-absorbing equalising material
BEPS-ÖNORM 6550-1-PS(2-6)N-LD70-FMD95-DMD80-MU5-CS(10)70-CC(1,5/1,0/10)10-DLT(1)5
Technical data
B2
E
B2
0,043 W/mK
30 mm
25 litres
2-6N
70 kg/m
LD
3
95 kg/m
FMD
Dry bulk
80 kg/m3
DMD
≤ 5μ
MU
≥ 70 kPa
CS (10)
35 kPa
CS (2)
Creep deformation
10 kPa
≤ 1,5%
≤ 1,0%
CC
temperature stress
≤ 5%
DLT (1)
Water absorption
≤ 2,0 kg/m2
Min. 45 min.
+5o /+30o C
Ca. 24 hours*
≤ 12 M-%
Ca. 24 hours**
Ca. 24 hours**
Ca. 24 hours**
Registration
Number
ON-N 2009 182
PS
3
11
E-55-30-150-70
Very fast hardening heat-absorbing equalising material
BEPS-PS(0-8)R-LD125-FMD195-DMD160-MU7-CS(10)70-CC(2,5/2,3/10)20-DLT(1)5
Technical data
Sack contents
200 Liter (21,5 - 24,0 kg)
Sack per pallet
16 Sack (3,2 m³)
B1/TR1/Q1
E
B2
0,055 W/mK
30 mm
150 mm
(superficial load 10 kN/m2)
70 litres
0-8R
PS
125 kg/m
LD
195 kg/m3
FMD
Dry bulk
160 kg/m
DMD
≤ 6μ
MU
3
3
≥ 70 kPa
CS (10)
≥ 35 kPa
CS (2)
Creep deformation
10 kPa
≤ 1,9%
≤ 0,8%
temperature stress
≤ 5%
Water absorption
≤ 3,0 kg/m2
20 kPa
≤ 2,5%
≤ 2,3%
Min. 30 min.
+5o /+35o C
2 - 3 hours*
≤ 12 M-%
Ca. 3 - 4 hours**
CC
DLT (1)
In connection with nanoestrich® – the quickest construction.
In only 9 hours, compensation insulation,
floor heating and nano-screed® possible.
12
Finished product
KOWLEDGE AND INFORMATION GIVES
YOU A WINNING MARGIN.
thermotec® express – Save time and money.
Before now, you had to go back and forth to small construction sites. Especially when enormous height compensation was required. thermotec® express gives you time.
So you are faster, more efficient and more flexible.
Take advantage of its benefits:
Foot traffic after 3 hours
Compensation insulation and screed in one day
Height adjustment up to 25 cm
Construction sites must be visited only once
Environmentally friendly and energy saving
Delivered in the morning, constructed by evening
Clean, fast and profitable
Ready for covering for screed after 3 hours
ur
sulates yo
in
s
s
e
r
p
x
e
r costs.
thermotec
u
o
y
d
n
a
ed
time requir
tion site!
c
u
r
t
s
n
o
c
velling to aEUR 10.000 per year)
a
r
t
e
im
t
e
to
v
®
The dry mix thermotec® express
which is premixed at the factory,
needs only to be mixed briefly
with water on-site and is
processed immediately.
Sa
, that is up
(At 100 sites
13
GENERAL INSTALLATION
INSTRUCTIONS
THERMOTEC® FINISHED PRODUCT AND
FREE BARE FLOOR/CEILING
PREPARATION:
The underground must be dry and
clean (swept).
thermotec® cannot be laid at temperatures below +5°C and above
+35°C at the point of introduction.
PROCESSING thermotec® finished product:
thermotec® is available in 200 lt
After filling the screed pump with
sacks (approx. 14-22 kg, depend1 sack of thermotec®, the water is
added slowly into the running pump
ing on the product) as a factory pre(see table).
mixed EPS-dry mortar.
No need to add additional binders or
For installation thicknesses under
additives!
6 cm on dusty underground and
®
thermotec is perfect for mixing
temperatures above +25°C one litre
and handling materials in convenof mixing water should be used.
After about 2 minutes mixing time,
tional screed pumps or with the MIX
the insulation can be spread widely
301D.
It is important to ensure that sacks
up to 150 m.
are not separated.
1 full bag = 1 whole mix
Mixing Water
each m3
per sack
Thickness
50 mm
Room Temp.
≥ 25°C
BEPS-T 90R
50 litres
10 litres
11 litres
11 litres
BEPS-WD 100R
50 litres
10 litres
11 litres
11 litres
PRODUCT
BEPS-WD 130R
55 litres
11 litres
12 litres
12 litres
BEPS-WD 150R express
70 litres
14 litres
15 litres
15 litres
PROCESSING free bare ceiling/wall:
The processing and installation of thermotec® free bare ceiling/wall is performed with microprocessor-controlled mixing mobiles.
Mix 1 sack (200 l) with 10-12 litres of water
(depending on product) in a screed pump to a
homogenous insulation (ca. 2 min. mixing time).
Train (bandage), pour in and compress, and
scrape off to level.
Rework the connector edge of the wall and
compress the applied surface.
LAYING:
It is important to ensure that the insulation material is compacted over the entire surface
before screeding (for example: with a large aluminum blade or with a large trowel).
CURING:
After laying, a minimum temperature
of +5°C must be ensured up to readiness for walking upon.
In the first 24 hours drafts should be
avoided or prevented.
It is necessary to check the insulation
layer before the first walking (acc.
ÖNORM B 6550-2 and DIN 18560-2).
Observe the safety data sheets!
14
The insulation layer may only be
used for under-floor heating installation purposes and for screed-laying.
Before laying the insulation layer, it
must be checked for dryness. Evidence of readiness is when the moisture content is below 12-M%.
Level surface ...
... and finished!
thermotec® Acoustic System Rail 6/500 - Z-1874 23:21 - B2-6.0-1.0: Impact sound
foam with laminated water vapour barrier. No film wrinkle. Ideal under nano-screed®
This 6 mm thick impact sound foam with laminated water vapour barrier and self-adhesive overlap is installed
in addition to thermotec® BEPS-WD 100R, WD 130R or
70N rapid as impact sound insulation and vapour barrier
in one. As a result of the width of 120 cm and the selfadhesive overlap strips, a high laying performance at low
extra cost is possible (hardly any tape required).
Technical data
Length
40 m
As system structure, an impact sound improvement of
28 dB at a construction depth of 120 mm is achieved
with thermotec® BEPS-WD 100R (from 60 mm) with a
laying of thermotec® Acoustic System Rail with 6 mm
and 50 mm screed.
Width
1,25 m
Thickness
6 mm
Design
Rolled goods with
adhesive foil/tape
Packaging
Roller in PE-sack
Nominal value of thermal conductivity λD
0,045 W/mK
Equivalent air layer thickness - sd-Wert
≥ 120 m
Temperature resistance in the short-term
long-term
80 - 85˚C
90˚C
Fire behaviour acc. to OENORM EN 13501-1
E
Fire behaviour acc. to DIN 4102
B2
Shape retention at +40˚C
< 10%
Thickness tolerance (acc. to OEN EN 13163)
± 1 mm
Length tolerance (acc. to OEN EN 13163)
-1%; + °°
Width tolerance (acc. to OEN EN 13163)
± 0,6%
Leakage test (acc. to DIN 16726)
Tight
Dynamic rigidity
115 MN/m3
Footfall sound reduction ΔLW, R
14 dB (with 60 mm
thermotec® BEPS-WD
100R 28 dB)
Compressibility
≤ 1 mm
This impact sound rail
was developed with
thermotec® and nanoscreed® in the system.
Contact us for advice!
Z-23.21-1874- B2 – 6.0- 1.0
Product composition/material
Extruded polyethylene
foam, closed-cell with
foil lamination,
100% HCFC and
HFC free
15
Adhesive tape
for fixing onto
the wall
Water vapour
barrier foil
SD = 120 m
PE-Foam
Impact sound
quality
Adhesive tape for
gluing the water
vapour barrier
16
thermotec® Vapour Control Layer –
0.2/1500; Polyethylene
Construction Film.
The thermotec® Edge Strips – 120+30/8
which meet the standard requirements.
Your advantage:
Wrinkle-free installation
Laying of the role
Optimal film width for fast, waste-optimized laying
Ideally combined with thermotec® Edge Strips
Your advantage:
Consistant film quality throughout up to the upper edge
edge strips
Simple foil gluing because of the adhesive tape applied
Tape also works at low temperatures
Logical assembly by the adhesive tape on the back for
fixing to the wall
Impact sound insulation material also on the edge strips
Technical data
Vapour Control Layer
Edge Strips
Product composition/material
Polyethylene foil
Extruded polyethylene foam,
closed-cell with foil lamination,
100% HCFC and HFC free
Length
50 m
40 m
Width (at the edge: height)
1,5 m
120 mm (+ 30 mm foot)
Thickness
0,2 mm
8 mm
Design
Rolled goods
Rolled goods with adhesive foil/tape
Packaging
52 rollers/pallets
Roller in PE-sack
Fire behaviour acc. to EN 13501-1
F
E
Water vapour permeability (acc. to EN 1931)
sd-Wert 140 m
sd-Wert ≥ 120 m
The thermotec® Underfloor Heating System – For you, a plus in temperature control.
With the thermotec ® System Underfloor Heating, flooring installations
with a total thickness of as low as
60 mm can be completely planned
and executed (including heat-and
impact sound insulation). With good
floor insulation and thin screeds, usable floor heating systems can quickly be built.
Your plus points of advantages:
Ideal construction for any type of underfloor heating system
Can be installed in new-builds and
renovations
Feasible in combination with nanoscreed® low construction heights
No more cold feet! Indeed, at any
place in the building. With the thermotec® Underfloor Heating System
you have the heat evenly distributed
over the entire floor surface. Highest
efficiency and spatial chararteristics.
You have never been so keen on floor
before!
17
thermotec® – CHECKED, CERTIFIED
AND RELEASED INTERNATIONALLY.
All the benefits of thermotec® at a glance.
Check for yourself.
thermotec® has an ETA (European Technical Approval)
by the German Institute for Building Technology (DIBT)
Eco-Norm certified heat and impact sound insulation
material
Laboratory-monitored quality products
Seamless installation without insulation value loss
Ensures uniform thickness screed plate
Dimensionally stable, lightweight, highly resilient
* Depending on the mounting strength, temperature, humidity and the product used
(see technical data).
18
Fast, dust-free application
Ideal for underfloor heating
Enormous installation height possible
Can be laid on slopes
Ready for walking upon from 3 hours*
Ready for laying of screed after 3 hours*
EUROPEAN ORGANISATION FOR
TECHNICAL APPROVAL
ÖNORM B 6550
REGISTRIERT!
The thermotec® MIXMOBIL
has many advantages:
Pumping 5-8 m³/hour for free
bare ceiling/wall
Various products in one visit
No additional processing
machines (for example,
screed pump, compressor,
hoses), devices, or tools
necessary
Computer-controlled
production system
Quality monitoring as per
European Technical Approvals
and OENORM B 6550-1
Self and external monitoring
Quality and speed in one:
The thermotec® MIXMOBIL
The thermotec® MIXMOBIL is a microprocessor-controlled mixing system with PC Monitor, for mixing all
thermotec® Insulation backfillers. The
production quality is factory production control ensured. An external test
institute monitors the products in
addition.
With the thermotec® MIXMOBIL different products can be produced at a construction site in one day.
The low set-up times and the small space
requirement as well as a clean construction site are equal advantages like the
high mixing and pumping capacity.
19
thermotec® − ENERGY SAVINGS AND
QUALITY YOU CAN FEEL AND EXPERIENCE.
Creation and Monitoring Quality
Binding materials, polystyrene ground stock and finished
dry mixes as well as and the finished laid insulation are
subject to our permanent in-house quality control. In each
batch, samples are taken and examined. Along with this,
we use state of the art testing methods. In addition, the
quality of our product is monitored according to the European Technical Approval and OENORM B 6550 part 1
continuously by external certified testing laboratories.
thermotec® partner companies are also subject to the central quality control and are committed to continuous production control.
A ++
A+
SAFETY / ENERGY EFFICIENCY RATING
Whether planning architects, builders, investors or the processing trade, all use this energy-saving document.
With the help of qualified energy consultation, you already
know in advance what you can save in energy in the future.
Your property gains in value with the energy certification
and you can also rent your property more easily, because
the warm rent is publicised.
A
B
C
D
E
F
G
20
ONE MORE POINT ON SAFETY
All thermotec® products are also subject to a variety of
tests: for instance fire protection, thermal insulation
compressive stress and sound-protection.
Thus you have a measurable increase of safety standards with thermotec®.
Mixit® – A NAME OF OBLIGATION
Develop and producing qualitative high-end products is a
constantly renewable obligation for Mixit® and its employees. The result is in a continuous reliability. Together with
our partners, we bring an increase of safety and environmental protection to thousands of construction sites.
We are also represented in national and international
standardization, as well as various labour and expert circles and we are an active co-designer of the technical
framework conditions in floor construction.
21
TRUST.
BUT VERIFY.
How do planners and
architects judge
thermotec®?
Marlies Egbers B.Sc. (Eng.), Architect,
Germany
I am obliged to carry out construction work according to the
latest state of the art technology for the builder owner. This
is especially true for sound and heat insulation. Through
the use of thermotec® I can ensure all this excellently. In
particular, the DIN 18560 is hereby complied with, where
pipelines, cables or similar installations on the bare ceiling/wall should be brought together in a bound balanced/
compensated layer.
thermotec® – competent and reliable.
Research and development are ongoing processes with us. Every little innovation is immediately incorporated into our product range. The most modern production equipment, strict production control and
our MIXMOBIL mixture quality on the construction site ensure that you will always receive the perfect
thermotec® quality.
Quality signed and sealed:
thermotec® quality is constantly monitored.
thermotec® is an OENORM certified heat and sound insulation material.
thermotec® has a European Technical Approval (ETA) from German Institute for Building
Technology (DIBT).
Give your vote in future to thermotec® and then you take care of a quality-conscious leveling of the floor.
22
Siegbert Schmidt, Installer,
Emile Rinnen, Rinnen Company,
Franz Wimberger, Master Builder,
Company Paul Schmidt, Germany
thermotec Contractor Partners,
Wimberger Company GmbH, Austria
®
Luxembourg
For the quality of underfloor heating, a proper instal-
For years we have built solid brick
lation of the heating systems is not only the crucial
For years, I have valued innovative and
prefabricated houses for our custom-
factor. The quality of a floor structure is largely deter-
economical solutions in my business.
ers. The thermotec® Insulation System
mined by the quality of heat and impact sound insu-
thermotec® solved all my problems in
guarantees us the highest quality in
lation in particular. Therefore, for our customers we
floor construction. As a result I have
floor construction. The punctual, na-
install the thermotec® Under Floor Heating System.
been able to gain some more regular
tionwide delivery and installation we
Underfloor heating, in combination with the ther-
customers again. The latest machine
leave to the thermotec® Partner Net-
motec® balance/compensation insulation materials
technology and the latest know-how is
work who guarantee the monitored
guarantee our customers a long-term, efficient and
mediated by thermotec Mixit Manufac-
quality until after installation and that
desirable living comfort.
turers through seminars.
at an affordable price.
®
1 German Historical Museum, Berlin
Compensation and insulation layers, 10-20 cm
below liquid screed in the Schlüterhof.
2 Fördeterrassen, Kiel
Here were built about 550 m³ of thermotec® BEPS T 90R
and thermotec® BEPS-WD 100R.
3 Office building in Dornbirn, Vorarlberg
Floor insulation under cement screed.
4 AQUA DOME Therme Längenfeld, Tirol
Gap/slope insulation up to 20 cm below the water tank,
filling of the shims/liners in the frames.
23
0137-03 Produktfolder thermotec EN 25.09.2014
THE QUALITY OF SITE
IS THE SUM OF ITS DETAILS.
www.thermotec.eu
THE ORIGINAL IS RED.
1
AUSTRIA:
GERMANY:
SWITZERLAND:
Thermotec Vertriebs GmbH
Galgenau 19
A-4212 Neumarkt i. M.
Phone: +43 (0) 79 42/778 11
Fax: +43 (0) 79 42/778 11-11
E-Mail: [email protected]
Thermotec Deutschland GmbH
Breslauer Straße 6
D-29633 Munster
Phone: +49 (0) 51 92/98 72 06–0
Fax: +49 (0) 51 92/98 72 06–1
Thermotec Schweiz GmbH
Gewerbestraße 5
CH-6330 Cham
Phone: +43 (0) 676/778 12 02
Fax: +43 (0) 55 72/ 20 37 78
Insulate professionally. Profit long-term.

NO MORE COLD FEET

Transcription

Similar documents

Jetons De Poker Ceramiques Casino Replica

protect - Steico

universal

BuildTog Flyer

Reliability - Comparato Nello srl

Astro-Foil RI bro

Earthwool Leaflet

expanded insulation corkboard

learn more

Polyisocyanurate Pipe Insulation