triode - JD Events

Santy Oropel
PO Box 681, Loma Linda , CA 92374
Tel. 909-954-2175
Mobile: 951-347-2732
email: [email protected]
TRIODE
TRIODE CORPORATION LTD - JAPAN
®
609-3 FUKUROYAMA, KOSHIGAYA-SHI, SAITAMA-KEN JAPAN 343-0032
TEL: +81-48-940-3852 ~ FAX: +81-48-940-3853 ~ URL: http://www.triode.co.jp
TRX-3 Full Function Tube Pre-Amplifier with MM
$5,000
Tubes: 12AX7 (ECC83) x 8, PsVane WE 274B x 1, Frequency Response: 10Hz-100KHz plus minus 2Db,
Signal to noise ratio: 97db, Input Sensitivity: 250mV, Equalizer Control Response: 150, 400, 2k, 10KHz
plus minus 6Db, Output Impedance: 6 K Ohm, Input Impedance: Line 100K Ohm, MM 47K ohm, Input
Terminal: Phono MM, Line 3, Balance 1, Output Terminal: Line 2, Balance 1,Other Function: Left/Right
Volume Balance, Low Cut Filter ( Phono), Critical components are Mundorf Caps Germany and Kiwame
precise Resistors from Japan
Dimension: W345 x D310 x H195 (mm), Weight: 30 lbs.
TRX-I Tube Pre-Amplifier- Remote Controlled.
$3200
Tubes: 274B x 1, 12AX7 x 4, Frequency response: 10Hz - 100KHz, S/N ratio: 96Db, Input Sensitivity:
250mV, 4 band Equalizer Frequency: 150, 400, 2K, 10KHz +/- 6Db: Input Impedance: 100K Ohms, Output
Impedance: 6 K Ohms, Input Terminal: 5, Output Terminal: 3 Power Consumption: 30W, Dimension: W340
x D315 X H187, Weight: 8 Kilos,
Resistors are made by Kiwame ( Made in Japan) and the capacitors are Mundorf made in Germany.
TRV-EQ3SE Tube Phono Equalizer Pre-Amp
$3150
NF Type MM MC Phono Equalizer- Frequency Response: 10Hz- 70 kHz (-1dB),Total Distortion: 0.1%,
Input Level: MM 2.5mV, MC Low 0.23mV, MC High 0.19mV, Input Impedance: MM 47K Ohms and MC
2-47 ohms, Gain: MM 42.5dB, MC Low 58.7dB, MC High 64.4dB, S/N Ration in Input: MM 90dB, MC
87dB, Maximum Input Capability: 250mV (1 kHz) 11mV, Output Voltage: 200mV(1,000Hz), RIAA Curve
Deviation: +/-0.25dB (20 to 20,000Hz), Channel Separation: More than 90dB, Low Cut Filter: 15Hz 18dB,
Input Terminals: 3 Lines (MM / MC1 / MC2), Output terminals: 2 Lines (RCA / XLR), Capacitors:
Mundorf, Resistors: Kiwame Resistors, Tubes: ECC803 x 4 (JJ Electronics), 5AR4 x 1 (JJ Electronics ),
Power consumption: 15 Watts, Dimension: W340 x D315 x H185 (mm) Weight:10.0Kgs.
TR-MC1 SE Step up Transformer
$1500
• Frequency response:10Hz -70kHz( -1dB)• Input Impedance MC 2 -47ohm • Gain MC Low 16dB, MC
High 22dB • Input terminal: 2 lines (MC1/ MC2) • Dimension W 180mm x D 155mm x H 145mm • Weight
2.5 kg
High step up efficiency with low transmission loss, Super-perm-alloy gigantic EI core transformer winded
uniquely divided into layers for wide bandwidth response and high rise time / Vibration free body structure
using heavy iron chassis. Reproduce realistic music with good S/N images
TRV-35SE Integrated / Amplifier
$2700
EL34 Class AB push-pull integrated amplifier, Output class AB: 45 Watts + 45 Watts at 8 ohms,
Frequency response: 10Hz- 100 kHz (+/- 4dB), Total distortion: 0.1% (1kHz), SN level: 90dB, Input
sensitivity: 0.4V, Input impedance: 100k ohm, Output: 6 and 8 ohm speaker taps and one headphone
terminal, Input terminals: 4 (front 1, rear 2, 1 Pre-Amp in), Output terminals: 1 (rec out 1), Tube
Compliments: 4- EL 34 1-12AX7(ECC83) 2- 12AU7 (ECC82), Power consumption: 120 watts(no signal),
max 240 watts, Components used: Nichicon caps, Real caps and Alps volume control. Dimension:
W340 x D315 x H 185 (mm), Weight: 15 Kgs
TRV-88SE Integrated / Amplifier
$2800
KT-88 Class AB push-pull integrated amplifier, Output class AB: 50 Watts + 50 Watts at 8 ohms,
Frequency response: 10Hz- 100 kHz (+/- 4dB),Total distortion: 0.1%(1kHz), SN level: 90dB, Input
sensitivity: 0.4V, Input impedance: 100k ohm, Output: 6 and 8 ohm speaker taps and one headphone
terminal, Input terminals: 4 (front 1, rear 3), Output terminals: 1 (rec out ), Tube Compliments: 4KT-88, 1-12AX7(ECC83), 2- 12AU7 (EC82), Power consumption: 120 watts (no signal), max 240 watts,
Dimension: W340 x D315 x H 185 (mm), Weight: 15 Kgs
TRV-88SE R Integrated Amplifier with Remote
$3100
Remote control: volume , mute • maximum output: 45W+45W ( 8 ohms) • output tube: KT88 AB class
push pull • Frequency response 10Hz-100 kHz ( -1,-4dB) • 4 inputs RCA ( 1 front and the 3 rears) MM
1, TAPE OUT1 • SN level 90dB • Output impedance 6 /8ohm •Total distortion < 0.1%(1kHz) • Input
sensitivity LINE 0.7V/100k Ω MM 2.5mV/47k Ω • Tubes KT88 *4, 12AU7 * 2,12AX7 *1 • Head phone
terminal • Power consumption min 100 watts/ max 220 watts • KOA highly precise resistor use • USA
quality speaker terminal use • Dim: (340W x185H x315D) mm • Weight: 15kg • Tube cover Grill •
Wooden side Panels
Type to enter text
Santy Oropel
PO Box 681, Loma Linda , CA 92374
Tel. 909-954-2175
Mobile: 951-347-2732
email: [email protected]
TRIODE
TRIODE CORPORATION LTD - JAPAN
®
609-3FUKUROYAMA, KOSHIGAYA-SHI, SAITAMA-KEN JAPAN 343-0032
TEL: +81-48-940-3852 ~ FAX: +81-48-940-3853 ~ URL: http://www.triode.co.jp
TRV-A300SE R
$3500
300B Single Ended Class A Integrated amplifier With MM Phono Stage, Headphone Amp and
Remote Control.
■ Maximum output: 8W+8W at 8 ohms■ Self bias ■ Output tube: 300B Class A Single Ended ■ Output
impedance: 6 / 8 Ohm ■ KOA highly precise resistor use ■ Top Grade Mundorf capacitors■ Frequency
response: 10Hz- 50 kHz (+1,-1dB)■ Total distortion: < 0.3%(1kHz)■ SN level: 87dB■ Input sensitivity:
0.8V 100 kOhm, MM 2.5mV 47kOhm ■ Tubes 300B * 2 , 12AX7*1 , 12AU7 *2 , 5AR4 *1 ■ Input terminals:
MM *1 , RCA *4 , TAPE OUT*1 ■ Power consumption:100 watts■ Dimension: 340Wx195Hx315D mm ■
Weight:16kg
TRV-845SE Integrated / Amplifier
$ 7800
Max Output Power : 20W per (Pure Class-A), Circuit : CR-Type Pre-main amplifier, T. H. D : 0.1%,
Frequency Response: 10Hz - 50 KHz (-1dB), S/N Ratio : 89dB, Input Sensitivity : 900mV, Input
Impedance :
100K ohm, Input Terminal : 3 x RCA , 1 x XLR , 1 x PRE-IN , Outputs : 4 / 8 / 16
Ohms, Tubes Compliments : 2 x 845 , 2 x 2A3 , 2 x 6SN7, Resistors: Japanese high-end carbon
resistors (KOA), Condensers : German MUNDORF condensers, Insulators : Solid aluminum insulator
(original), Remote Control : Volume , Input Selector , Muting, Power Consumption : 300W,
Dimensions : 460 (W) x 450 (D) x 260 (H) mm, Weight : 85 Lbs.
TRV-HD82
Vacuum Tube Headphone Amplifier with USB input
$1750
Class A circuit with 6MB8 Output tube, Digital Analog Converter: Burr Brown PCM 1798 24 bit/192kHz,
USB controller: TE TE7022 , USB ( Type B ): 16/24 bit 32K,44.1k,48k,88.2k,96kHz, PC-USB can handle
WPA,MP3, TONE:Bass +/- 6dB, Treble +/-6dB, Rated Output impedance:20 OHMS-600 OHMS Output
Tubes (45mW- 135mW), 12 OHMS-300OHMS Output Transistors ( 40mW-120mW), Frequency
Characteristic: 10Hz -50kHz at +/- 1dB, S/N Ration: 89dB, Inputs: PC-USB ( B ), USB 9A),Line 2, Output
Tubes: 2 x 6MB8, Power Consumption: 30W, Dim: 250 x 190 x 150 ( mm), Weight: 4.5 kilos =/
TRX-PM84
$2750
With Headphone, USB DAC and MM Phono Stage.
DAC: Burr-Brown made PCM 1798, 24 bit 192 KHz , PC-USB (Type B ): Accepts :16 / 24 bit, 32 KHz / 44.1
KHz / 48 KHz / 88.2 KHz / 96 KHz, USB Memory (Type A ): Accepts MP3 / AAC / WMA · 32 KHz / 44.1
KHz / 48 kHz, Circuit type: 6BQ5 (EL84) AB class Push-Pull, Rated Output: 15W +15 W (8Ω), Frequency
Response: 15Hz ~ 50 kHz ( ± 1dB ), SN ratio: 87Db, Input sensitivity: Line / 290 mV · 100kΩ, MM/10mV ·
47 KΩ, Input: MM phono system x 1, Line in x 2, PC-USB (Type B ) x 1 system, USB memory (Type A )
x1, Output: x1 Speaker system (4 ~ 8Ω), Headphone jack ( vacuum tube circuits ), Vacuum tube: Output
tube 6BQ5 x 4, first stage 12AX7 x 1 , driver 12AU7 x 2, Power Consumption: 130 W, Dimensions: (W)
12 inches x (H) 6.1 inches x (D) 10.3 inches, Weight: 12.2 kg
TRV-84HD MKII HEADPHONE AMP
$2100
Maximum output: 3W + 3W, 600 mW +600 mW headphone jack, speaker terminal (8Ω) (Class A),
Frequency characteristic: 30Hz-50kHz (± 1dB), THD: 5% up to 0.1% at rated output, SN Ratio:85 dB,
Input Sensitivity:0.52V, Vacuum tube: EL84 (6BQ5) × 2, 12AU7 × 2, Input Impedance: 100kΩ, Output
impedance: more than 20Ω [headphone], [Speaker Terminals] 4 and 8Ω
Two pairs of line input terminal RCA, headphone output, speaker output jacks, speaker ON / OFF switch
Power Consumption: 40 W
Weight: 8.5kg
Dim: 14 depth x 6.3 height x 5.9 Width (inches)
RUBY
$1500
Circuit type: Single ended 6BQ5 Amplifier: Vacuum tube: 6BQ5 x 2, this 12AX7 x 2: Headphone: Vacuum tube
circuit: Rated output: 3W +3 W (8Ω): Frequency characteristic: 30 Hz ~ 40 kHz (± 2dB): S N ratio: 88dB
Input Sensitivity: 800mV/100kΩ: Input Terminal: 2 pairs of RCA: Speaker output terminal: 4 ~ 8Ω
Power Consumption: 40W when there is no signal and 80 W at the maximum output
Dimension: 6.99 depth x 7.5 height x 5.2 Width ( inches)
Weight: 4.7kg:
Accessories: tube cover, power cable, 2 spare fuses this
Santy Oropel
PO Box 681, Loma Linda , CA 92374
Tel. 909-954-2175
Mobile: 951-347-2732
email: [email protected]
TRIODE
TRIODE CORPORATION LTD - JAPAN
®
609-3FUKUROYAMA, KOSHIGAYA-SHI, SAITAMA-KEN JAPAN 343-0032
TEL: +81-48-940-3852 ~ FAX: +81-48-940-3853 ~ URL: http://www.triode.co.jp
TRX-P3M
$6200
300B Parallel Single Ended CLASS A Mono Blocks amplifier, Output: 20W + 20W at 8 ohms,
Frequency response: 10Hz-60Hz (+1, -3 db), Output: 6, 8, 16 ohms speaker taps, Total Distortion: 0.3%
(1KHz), S/N Ratio: 89 db, Input Gain selector: 0dB, -3dB, -6dB, Input Sensitivity: 800 mV, Tubes
Compliment: Each mono block, 2-300B 1-12AU7, 1-12BH, Input terminal: one XLR, one RCA, Kiwame
carbonized silicon precision resistors and Alps volume control, Tube Socket TRV UX-4P special grade
with OFC 24K Gold. Dimension: 176(W) x 200(H) x 440 (D) (mm), Weight: 15 Kgs each.
TRV-M88SE
$4300
KT88 Push-Pull Mono power amplifier, Output: Class AB, 60 watts +60 watts at 8 ohms,
Frequency response: 20Hz- 55 kHz (+/- 1dB), Total distortion: 0.1%(1 kHz), SN level: 90dB, Input
sensitivity: 0.7V, Input impedance: 100 K ohm, Output: 6, 8, 16 ohms speaker taps, Input terminals: 1
balanced, 1 RCA , Power consumption: 60 watts(no signal), max 120 watts, Tube Compliments: In
each mono block, 2- KT88 1-12AX7 (ECC83) 1- 12AU7 (ECC82),
Dimension: W176 mm * D440 mm * H 200 mm , Weight 15 kgs each,
TRX- M845SE -
$22,500
Monoblock Power Amplifier, 845 or 211 tubes driving 845 in parallel Single Ended Class A design
with Auto bias.
■ Maximum output: Class A 50 Watts at 8 Ohms ■ Output Impedance: 4 / 6 / 8 / 16 ohm ■ Frequency
response: 10Hz- 50 kHz (0,-3dB)■ Total distortion: < 0.1%(1kHz) ■ SN level: 89dB ■ Input sensitivity
0.8V■ Tubes: 845 * 3 , 6SN7 * 1 ,12AU7 * 1 ■ Input terminals: one pair RCA and one pair XLR■ Power
Consumption: 380 watts ■ Dimension: 580W x 300H x 440Dmm ■Weight: 55 kgs■ Compliment: Three
845 tubes, One 211 tubes, one 6SN7, one 12AU7, tube cage, power cable, spare fuses
TRX-M300 Monoblock
$14,000
300B tube driven by 91A tube in Single Ended class A design with Auto bias. Faceplate, Top chassis and
Top transformer cover are machined military Grade Aluminum. Simple yet beautiful.
■ Maximum output: Class A 8 Watts at 8 Ohms
■ Output Impedance: 4 / 6 / 8 / 16 ohm
■ Frequency response: 10Hz- 50 kHz (0,-3dB)
■ Total distortion: < 0.1%(1kHz)
■ SN level: 87dB
■ Input Impedance: 800mV/ 100kOhms
■ Input terminals: one pair RCA and one pair XLR
■ Compliment/Mono One 300B tube, Two 91A tube, one 274B tube, tube cage, power cable, fuses.
■Weight: 60 Pounds
TRV-M88PP Mono Block
$14,500
KT - 88 Push Pull Amplifier Maximum output: Class AB Ultra linear- 200 watts, Triode-125 watts @
8 Ohms, Output impedance: 4, 6, 8, 16 Ohms, Frequency response: 10Hz –100 KHz ( 0, - 5DB),
Total distortion: <0.1% (1 KHz), SN level: 90 DB, Input sensitivity: 1.0V, Input terminals: WBT RCA 1, XLR
1, Output Tube compliments: 8 pieces KT88 , 3 pieces 6SN7, Resistors: Kiwame precise KOA resistorsJapan, Capacitor: Nichicon high end caps. Power Consumption: 200 watts,
Dimensions: 440 mm (W) X 210 mm (H)X 450 mm (D), Weight : 35 Kgs each.
TRX-88PP
$7500
Remote Controlled Class A Parallel Push Pull KT88 Integrated Amplifier with Self Bias.
Rated Output: 50W + 50W @ 8 OHMS, Frequency characteristics:-2dB (10Hz ~ 60kHz), S/N ratio: 91dB,
Output Terminal: 6 and 8 OHMS, Input Impedance: 100 kOhms, Inputs: 1x MM Phono stage, 4 Line
inputs, one Pre -Amplifier ( can be used as a stand alone Amplifier), Outputs: One Pre-Out ( can be used
as a stand alone Pre-Amplifier) and One Tape Out, Bass and Treble control are included, Dimensions: 430
x 460 x 180 ( mm), Weight: 37 Kgs.,
All components like Capacitors, Resistors and others are all top grade quality.
Santy Oropel
PO Box 681, Loma Linda , CA 92374
Tel. 909-954-2175
Mobile: 951-347-2732
email: [email protected]
TRIODE
TRIODE CORPORATION LTD - JAPAN
®
TRX-P6L Amplifier
609-3FUKUROYAMA, KOSHIGAYA-SHI, SAITAMA-KEN JAPAN 343-0032
TEL: +81-48-940-3852 ~ FAX: +81-48-940-3853 ~ URL: http://www.triode.co.jp
$3200
6L6GC, EL-34 and KT88 Tubes can be used to power this amplifier. Tubes: 6L6GC x 4, 12AX7 x 2,
12BH7 x 2, Class AB Push Pull, Automatic bias, Output power: 6L6GC -UL @ 25 W & Triode @ 12 W,
KT88 - UL @ 30W & Triode @ 15W, EL34 - UL @ 30W & Triode @ 15W. Frequency Response: 10Hz 100KHz, S/N ratio: 90Db, input Sensitivity: 600mV, Input Impedance: 100K Ohms, Input Gain: 0, -3, -6
Db, NFB: 0, 3, 6 Db, Input Terminal: RCA, Output terminal: 4, 6, 8 ohms, Power Consumption no signal:
100W max, Dim: W340 x D315 x H187 (mm), Weight: 15 Kilos.
TRV-P845SE
$8199
Single Ended Class A Design Stand Alone Amplifier.
Output Power: 20W + 20 Watts ( 8 Ohms), Adjustable Fix bias, Frequency Characteristic:-1, -4dB (10Hz50kHz), S/N Ratio: 90dB, Input Impedance: 100K ohms Unbalance,100K ohms Balance, Input Terminal:
one pair RCA and One Pair XLR, Input Level Adjustment: 0, -3, -6-12dB, (rear switch), Output Terminal: 4,
6, 8 Ohms, 1st Stage tube 12 AX7 x 2 , dDriver stage 2A3 x 2, Output Stage 845 x 2 , Dimension: 430 x
445 x 257 ( mm), weight: 42 kilos. Side panel is real wood, Resistors used is Kawame precise resistors,
Caps are Mundorf.
TRV-DAC 1.0
Remote Controlled 24Bit/192kHz Asynchronous Tube Digital Analog Converter
with 2 High Speed USB inputs.
$2499
Two 6DJ8 output tubes and one 6N1 power regulator tube, DA Converter: Burr Brown PCM1792,Sampling
Rate Converter:CS8422, USB Receiver:XMOS ( 192kHZ). Analog Output Section: Output level:2.2V
+/-1db. Headphone output:100mW 32ohms, Frequency Characteristic: 20Hz - 20kHz+/0.3dB,Distortion:Below 60dB, Dynamic range: 100dB, S/N Ratio: 92dB,Channel Separation: 90dB (1kHz),
Headphone Output: 6.3 mm diameter. Digital Input Section: Sampling Frequency:44.1,48, 88.2, 96, 176.4,
192 kHz, Resolution: OS Windows XP, Vista, Mac OS-X support 16-24 bit ( 10.6.4 or higher), 2 USB 2.0 high
speed compliance inputs, 3 S/PDIF coaxial inputs, I toslink Input, one Selector Switch each for Digital
Signal Phase,Sampling rate converter and Solid State or Tube Output, Power Consumption:30W, Dim.: 330
x 342x 89 (mm), Weight: 6.8 kilos.
$3200
TRV-CD5SE
Tube Output with USB, Optical and Coax input. Could be use as Stand Alone DAC.
Specification: Output Level: 2.2V+/- 1 dB RCA & 4.6+/-db Balance,Headphone Output Frequency
response 20Hz -20KHz +/-1db, Frequency Response: 20Hz-20kHz=/-0.3dB, Distortion & Noise :<-60dB,
S/N Ratio: 92dB, Dynamic Range: 100dB, Channel Separation: 90dB (1kHz),Digital Output:IEC958
Standard, Digital Input : Sampling Frequency rates: 44.1, 48, 88.2 96, 176.4 and 192Khz, Word Length:
16-24 bits, Digital Input Impedance: 75Ohms, USB interface: USB 2.0 high Speed Operating Systems of
USB input: WindowsXp,Vista,7 and Mac OS ( 10.6.3 and above)Weight 8.5 kg, Dimension :342 x 326 x 107
(mm), Power Consumption:30W