Satellite P20 User`s Manual

Transcription

Satellite
User’s Manual
P20 User’s Manual
P20
T202014-EN
SATELLITE P20 SATELLITE P20 SATELLITE P20 SATELLITE P20 SATELLITE P20 SATELLITE P20
Choose freedom.
computers.toshiba-europe.com
Satellite P20 Version
1 Last Saved on 30/05/2003 13:57
User's Manual
Copyright
© 2003 by TOSHIBA Corporation. All rights reserved. Under the copyright
laws, this manual cannot be reproduced in any form without the prior
written permission of TOSHIBA. No patent liability is assumed, with
respect to the use of the information contained herein.
TOSHIBA Satellite P20 Series Portable Personal Computer User’s Manual
First edition June 2003
Disclaimer
This manual has been validated and reviewed for accuracy. The
instructions and descriptions it contains are accurate for the Satellite P20
series Portable Personal Computers at the time of this manual’s
production. However, succeeding computers and manuals are subject to
change without notice. TOSHIBA assumes no liability for damages
incurred directly or indirectly from errors, omissions or discrepancies
between the computer and the manual.
Trademarks
IBM is a registered trademark and IBM PC, OS/2, and PS/2 are
trademarks of International Business Machines Corporation. Celeron,
Intel, Intel SpeedStep, and Pentium are trademarks or registered
trademarks of Intel Corporation or its subsidiaries in the United States
and other countries.
MS-DOS, Microsoft, Windows and DirectX are registered trademarks of
Microsoft Corporation.
Centronics is a registered trademark of Centronics Data Computer
Corporation. Photo CD is a trademark of Eastman Kodak.
Bluetooth is a trademark owned by its proprietor and used by TOSHIBA
under license.
i.LINK is a trademark of Sony Corporation.
Other trademarks and registered trademarks not listed above may be
used in this manual.
Macrovision License of Notice
This product incorporates copyright protection technology that is
protected by methods and claims of certain U.S. patents and other
intellectual rights owned by Macrovision Corporation, and other rights
owners. Use of this copyright protection technology must be authorized
by Macrovision Corporation and is intended for home and other limited
viewing uses only unless authorized by Macrovision Corporation. Reverse
engineering of disassembly is prohibited.
Satellite P20
ii
ENGLISH using Euro_M.dot –– Printed on 30/05/2003 as T202014-EN
1 Last Saved on 30/05/2003 13:57
User's Manual
Safety Instructions
Use the following safety guidelines to help protect yourself and your
computer.
When Using Your Computer
Do not operate your portable computer for an extended period of time
with the base resting directly on your body. With extended operation, heat
can potentially build up in the base. Allowing sustained contact with the
skin could cause discomfort or, eventually, a burn.
■ Do not attempt to service the computer yourself. Always flow
installation instructions closely.
■ Do not carry a battery in your pocket, purse, or other container where
metal objects (such as car keys) could short-circuit the battery
terminals. The resulting excessive current follow can cause extremely
high temperatures and may result in damage from burns.
■ Be sure that noting rests on your AC adapter’s power cable and that
the cable is not located where it can be tripped over or stepped on.
■ Place the AC adapter in a ventilated area, such as a desk top or on
the floor, when you use it to run the computer or to charge the battery.
Do not cover the AC adapter with papers or other items that will
reduce cooling; also, do not use the AC adapter while it is inside a
carrying case.
■ Use only the AC adapter and batteries that are approved for use with
this computer. Use of another type of battery or AC adapter may risk
fire or explosion.
■ Before you connect the computer to a power source, ensure that the
voltage rating of the AC adapter matches that of the available power
source.
■ 903 115 V/60Hz in most of North and south America and some Far
Eastern countries such as Taiwan.
■ 904 100 V/50Hz in eastern Japan and 100 V/60Hz in western
Japan.
■ 905 230 V/50 Hz in most of Europe, the Middle East, and the Far
East.
■ If you use an extension cable with your AC adapter, ensure that the
total ampere rating of the products plugged in to the extension cable
does not exceed the ampere rating of the extension cable.
■ To remove power from the computer, turn it off, remove the battery,
and disconnect the AC adapter from the electrical out let.
■ To help avoid the potential hazard of electric shock, do not connect or
disconnect any cables or perform maintenance or reconfiguration of
this product during an electrical storm.
■ When setting up the computer for work, place it on a level surface.
Satellite P20
iii
1 Last Saved on 30/05/2003 13:57
User's Manual
■ Do not dispose of batteries in a fire. They may explode. Check with
local authorities for disposal instructions.
■ When travelling, do not check the computer as baggage. You can put
your computer through an X-ray security machine, but never put your
computer through a metal detector. If you have the computer checked
by hand, be sure to have a charged battery available in case you are
asked to turn on the computer.
■ When travelling with the hard drive removed from the computer, warp
the drive in a non-conducting material, such as cloth or paper. If you
have the drive checked by hand, be ready to install the drive in the
computer. Your can put the hard drive through an X-ray security
machine, but never, but the drive through a metal detector.
■ When travelling, do not place the computer in overhead storage
compartments where it could slide around. Do not drop your
computer or subject it to other mechanical shocks.
■ Protect your computer, battery, and hard drive from environmental
hazards such as dirt, dust, food, liquids, temperature extremes, and
overexposure to sunlight.
■ When you move your computer between environments with very
different temperature and/or humidity ranges, condensation may form
on or within the computer. To avoid damaging the computer, allow
sufficient time for the moisture to evaporate before using the
computer.
When taking the computer from low-temperature conditions into a warmer
environment or from high-temperature conditions into a cooler
environments, allow the computer to acclimate to room temperature
before turning or power.
■ When you disconnect a cable, pull on its connector or on its strain
relief loop, not on the cable itself. As you pull out the connector, keep
it evenly aligned to avoid bending any connector pins. Also, before
you connect a cable make sure both connectors are correctly oriented
and aligned.
■ Before you clean your computer, turn if off, unplug it from its power
source, and remove the battery.
■ Handle components with care. Hold a component such as a memory
module by its edges, not its pins.
When using your telephone equipment, basic safety precautions should
always be followed to reduce the risk of fire, electric shock and injury to
persons, including the following:
Satellite P20
iv
1 Last Saved on 30/05/2003 13:57
User's Manual
■ Do not use this product near water, for example, near a bathtub,
washing bowl, kitchen sink or laundry tub, in a wet basement or near
a swimming pool.
■ Avoid using a telephone (other than a cordless type) during an
electrical storm. There may be a remote risk of electric shock from
lightning.
■ Do not use the telephone to report a gas leak in the vicinity of the
leak.
■ Use only the power cord indicated in this manual.
■ Replace only with the same or equivalent type battery recommended
by the manufacturer.
■ Dispose of used batteries according to the manufacturer’s
instructions.
EU Declaration of Conformity
TOSHIBA declares, that the product: Satellite P20 conforms to the
following Standards:
Supplementary Information: “The product complies with the requirements
of the Low Voltage Directive 73/23/EEC and the EMC Directive 89/336/
EEC and/or the R&TTE Directive 1999/05/EEC.”
This product is carrying the CE-Mark in accordance with the related
European
Directives. Responsible for CE-Marking is TOSHIBA Europe,
Hammfelddamm 8, 41460 Neuss, Germany.
Canadian Regulatory Information (Canada Only)
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus as set out in the Radio Interference
Regulation of the Canadian Department of Communications.
Note that Canadian Department of Communications (DOC) regulations
provide, that changes or modifications not expressly approved by
TOSHIBA Corporation could void your authority to operate this
equipment.
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appareil numérique de la class B respecte toutes les exgences du
Règlement sur le matériel brouilleur du Canada.
Satellite P20
v
1 Last Saved on 30/05/2003 13:57
User's Manual
CD-ROM, DVD-ROM, CD-R/RW, CD-RW/DVD-ROM,
DVD-R/-RW, DVD-Multi drives Safety Instruction
CD-ROM, DVD-ROM, CD-R/RW, CD-RW/DVD-ROM, DVD-R/-RW and
DVD Multi drives employ a laser system. To ensure proper use of this
product, please read this instruction manual carefully and retain for future
reference. Should the unit ever require maintenance, contact an
authorized service location.
Use of controls, adjustments or the performance of procedures other than
those specified may result in hazardous radiation exposure.
To prevent direct exposure to the laser beam, do not try to open the
enclosure.
Location of the required label
Sample shown below. Location of the label on the drive and
manufacturing information may vary.
TOSHIBA CORPORATION
1-1, SHIBAURA 1-CHOME
MINATO-KU, TOKYO 105-8001,
JAPAN
Satellite P20
vi
1 Last Saved on 30/05/2003 13:57
User's Manual
CAUTION: This appliance contains a laser system and is classified as a
“CLASS 1 LASER PRODUCT”. To use this model properly, read the
instruction manual carefully and keep it for your future reference. In case
of any trouble with this model, please contact your nearest “AUTHORIZED
service station”. To prevent direct exposure to the laser beam, do not try
to open the enclosure. Use of controls or adjustments or performance of
procedures other than those specified in the owner’s manual may result in
hazardous radiation exposure.
VORSICHT: Dieses Gerät enthält ein Laser- System und ist als
“LASERSCHUTZKLASSE 1 PRODUKT” klassifiziert. Für den richtigen
Gebrauch dieses Modells lesen Sie bitte die Bedienungsanleitung
sorgfältig durch und bewahren diese bitte als Referenz auf. Falls Probleme
mit diesem Modell auftreten, benachrichtigen Sie bitte die nächste
“autorisierte Service-Vertretung”. Um einen direkten Kontakt mit dem
Laserstrahl zu vermeiden darf das Gerät nicht geöffnet werden.
ADVARSEL: Denne mærking er anbragt udvendigt på apparatet og
indikerer, at apparatet arbejder med laserstråler af klasse 1, hviket
betyder, at der anvendes laserstrlier af svageste klasse, og at man ikke på
apparatets yderside kan bilve udsat for utilladellg kraftig stråling.
APPARATET BOR KUN ÅBNES AF FAGFOLK MED SÆRLIGT
KENDSKAB TIL APPARATER MED LASERSTRÅLER!
Indvendigt i apparatet er anbragt den her gengivne advarselsmækning,
som advarer imod at foretage sådanne indgreb i apparatet, at man kan
komme til at udsætte sig for laserstråling.
OBS! Apparaten innehåller laserkomponent som avger laserstråining
överstigande gränsen för laserklass 1.
VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka
lähetää näkymätöntä silmilie vaarallista lasersäteilyä.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S
MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
VORSICHT: DIE VERWENDUNG VON ANDEREN STEURUNGEN ODER
EINSTELLUNGEN ODER DAS DURCHFÜHREN VON ANDEREN
VORGÄNGEN ALS IN DER BEDIENUNGSANLEITUNG BESCHRIEBEN
KÖNNEN GEFÄHRLICHE STRAHLENEXPOSITIONEN ZUR FOLGE
HABEN.
Satellite P20
vii
1 Last Saved on 30/05/2003 13:57
User's Manual
Description on Laser specification
The optical drive such as CD-ROM, DVD-ROM, CD-R/RW,
CD-RW/DVD-ROM, DVD-R/-RW and DVD Multi drive that is used in this
computer is equipped with laser. The classification label with the
following sentence is affixed to the surface of the drive.
CLASS 1 LASER PRODUCT
LASER KLASSE 1
LUOKAN 1 LASERLAITE
APPAREIL A LASER DE CLASSE 1
KLASS 1 LASER APPARAT
The drive with the above label is certified by the manufacturer that the
drive complies with the requirement for laser product on the date of
manufacturing pursuant to article 21 of Code of Federal Regulations by
the United States of America, Department of Health & Human Services,
Food and Drug Administration.
In other countries, the drive is certified to comply with the requirement
pursuant to IEC 825 and EN60825 on class 1 laser product.
This computer is equipped with the optical drive in the following list
according to the model.
Manufacturer
Type
Matsushita
UJ-811
Matsushita
SR-8177
TOSHIBA
SD-C2612
TOSHIBA
SD-R6112
Matsushita
UJDA750TT4-A
TOSHIBA
SD-R2412
TEAC
224E-85
Satellite P20
viii
1 Last Saved on 30/05/2003 13:57
User's Manual
Modem warning notice
Conformity Statement
The equipment has been approved to [Commission Decision “CTR21”] for
pan-European single terminal connection to the Public Switched
Telephone Network (PSTN).
However, due to differences between the individual PSTNs provided in
different countries/regions the approval does not, of itself, give an
unconditional assurance of successful operation on every PSTN network
termination point.
In the event of problems, you should contact your equipment supplier in
the first instance.
Network Compatibility Statement
This product is designed to work with, and is compatible with the
following networks. It has been tested to and found to conform with the
additional requirements contained in EG 201 121.
Germany
- ATAAB AN005, AN006, AN007, AN009, AN010,
and DE03, 04, 05, 08, 09, 12, 14, 17
Greece
- ATAAB AN005, AN006 and GR01, 02, 03, 04
Portugal
- ATAAB AN001, 005, 006, 007, 011 and
P03, 04, 08, 10
Spain
- ATAAB AN005, 007, 012, and ES01
Switzerland
- ATAAB AN002
All other
countries/regions
- ATAAB AN003, 004
Specific switch settings or software setup are required for each network,
please refer to the relevant sections of the user guide for more details.
The hookflash (timed break register recall) function is subject to separate
national type approval. It has not been tested for conformity to national
type regulations, and no guarantee of successful operation of that
specific function on specific national networks can be given.
Satellite P20
ix
1 Last Saved on 30/05/2003 13:57
User's Manual
Important Notice
Copyrighted works including, but not limited to music, video, computer
program, databases are protected by copyright laws. Unless specifically
permitted under applicable copyright laws, you cannot copy, modify,
assign, transmit or otherwise dispose of any copyrighted work with the
consent of the owner of the copyright.
Please take notice that unauthorized copying, modification, assignment,
transmission and disposition may be subject to claims for damages and
penalties.
HTT (Hyper-Threading Technology)
This is an innovative technology created by Intel and built into all their
new CPUs, including the one in this computer. It allows a CPU to do two
things at once (in technical terms, to run multiple task threads from a
program) which gives it a faster response time and better performance.
Not all models will come with HTT.
Bluetooth Technology
Some models of the computer will come with Bluetooth technology built
into it. Bluetooth was developed jointly by Ericsson, IBM, Intel, Nokia and
TOSHIBA. It uses a shortwave radio frequency to connect devices such
as cell phones, personal digital assistants, and computers. Essentially,
any device with a Bluetooth chip can connect to and communicate with
any other device with the same type of chip as long as the two are within
range of one another.
Not all models come with Bluetooth technology.
Precautions
TOSHIBA computers are designed to optimise safety, minimize strain and
withstand the rigors of portability. However, certain precautions should be
observed to further reduce the risk of personal injury or damage to the
computer. Be certain to read these general precautions and to note the
cautions included in the text of the manual.
Satellite P20
x
1 Last Saved on 30/05/2003 13:57
User's Manual
Stress injury
Carefully read the Safety Instruction Manual. It contains information on
prevention of stress injuries to your hands and wrists that can be caused
by extensive keyboard use. Chapter 3, Getting Started, also includes
information on work space design, posture and lighting that can help
reduce physical stress.
Heat injury
■ Avoid prolonged physical contact with the bottom of the computer. If
the computer is used for long periods, its surface can become very
warm. While the temperature will not feel hot to the touch, if you
maintain physical contact with the computer for a long time (if you rest
the computer on your lap, for example) your skin might suffer low-heat
injury.
■ If the computer has been used for a long time, avoid direct contact
with the metal plate supporting the I/O ports. It can become hot.
■ The surface of the AC adaptor can become hot when in use. This
condition does not indicate a malfunction. If you need to transport the
AC adaptor, disconnect it and let it cool before moving it.
■ Do not lay the AC adaptor on a material that is sensitive to heat. The
material could be damaged.
PC Card overheating
Some PC cards can become hot with prolonged use. If two cards are
installed, both can become hot even if only one is used extensively.
Overheating of a PC Card can result in errors or instability in the PC Card
operation. Also be careful when you remove a PC Card that has been
used for a long time.
Pressure or impact damage
Do not apply heavy pressure to the computer or subject it to strong
impact. Excessive pressure or impact can damage computer
components or otherwise cause malfunctions.
Mobile phone
Use of mobile phones can interfere with the audio system. Computer
operation is not impaired but it is recommended that a distance of 30cm
be maintained between the computer and a mobile phone in use.
Satellite P20
xi
1 Last Saved on 30/05/2003 13:57
User's Manual
Central Processing Unit ("CPU") Performance Disclaimer
CPU performance in your computer product may vary from specifications
under the following conditions:
■ Use of certain peripheral products
■ Use of battery power instead of AC power
■ Use of certain multimedia games or videos with special effects
■ Use of standard telephone lines or low speed network connections
■ Use of complex modelling software, such as high end computer aided
design applications
■ Use of the computer in areas with low air pressure (high altitude >
1,000 meters or > 3,280 feet above sea level)
■ Use of the computer at temperatures outside the range of 5°C to 35°C
(41°F to 95°F) or > 25°C (77°F) at high altitude (all temperature
references are approximate).
■ CPU performance may also vary from specifications due to design
configuration.
Under some conditions, your computer product may automatically shut
down. This is a normal protective feature designed to reduce the risk of
lost data or damage to the product when used outside recommended
conditions.
To avoid risk of lost data, always make back-up copies of data by
periodically storing it on an external storage medium. For optimum
performance, use your computer product only under recommended
conditions. Read additional restrictions in bundled documents.
Contact TOSHIBA Service and Support for more information.
LCD Display
Small bright dots may appear on your TFT display when you turn on your
PC. Your display contains an extremely large number of thinfilmtransistors (TFT) and is manufactured using high-precision technology.
Any small bright dots that may appear on your display are an intrinsic
characteristic of the TFT manufacturing technology.
CE compliance
This product and the original options are designed to observe the related
EMC (Electromagnetic compatibility) and safety standards. However,
TOSHIBA should not guarantee that this product still observes these EMC
standards if options or cables not produced by TOSHIBA are connected
or implemented. In this case the persons who have connected /
implemented those options / cables have to assure that the system
(PC plus options / cables) still fulfils the required standards. To avoid in
general EMC problems following advice should be observed:
■ Only CE marked options should be connected / implemented
■ Only best shielded cables should be connected
Satellite P20
xii
1 Last Saved on 30/05/2003 13:57
User's Manual
Working environment
This product was designed to fulfil the EMC (electromagnetic
compatibility) requirements to be observed for so-called "Residential,
commercial and light industry environments".
TOSHIBA do not approve the use of this product in working environments
other than the above mentioned "Residential, commercial and light
industry environments".
For example, the following environments are not approved:
■ Industrial Environments (environments with a mains voltage >230V~)
■ Medical Environments
■ Automotive Environments
■ Aircraft Environments
If this product is supplied with a network port, please refer to the
paragraph "Network connection".
Any consequences resulting from the use of this product in working
environments that are not approved are not the responsibility of TOSHIBA
Europe GmbH.
The consequences of the use of this product in non-approved working
environments may be:
■ Interference with other devices or machines in the near surrounding
area
■ Malfunction of, or data loss from, this product caused by disturbances
generated by other devices or machines in the near surrounding area
Therefore TOSHIBA strongly recommend that the electromagnetic
compatibility of this product should be suitably tested in all non-approved
working environments before use. In the case of automobiles or aircraft,
the manufacturer or airline respectively should be asked for permission
before use of this product.
Furthermore, for general safety reasons, the use of this product in
environments with explosive atmospheres is not permitted.
Satellite P20
xiii
1 Last Saved on 30/05/2003 13:57
User's Manual
Network connection (class A warning)
If this product has networking capabilities and will be connected to a
network, Class A radiation limits will be observed (in accordance with
technical conventions). This means that if the product will be used in a
domestic environment, other devices in the near surrounding may suffer
interference. Consequently, please do not use this product in such
environments (for example a living room), otherwise you could be held
responsible for any ensuing interference.
Information on the secure use of the CD-RW
Please adhere to the following information on the use of the CD-RW to
minimise the risk of unsuccessful storing process. As the storing may be
unsuccessful despite your adhering to these information, for example
because of a defective storing medium, you should even if the software
indicates a successful storage, always check if the data has been stored
successfully.
About TOSHIBA Wireless Solution
Wireless LAN Card Types
The Wireless LAN Card is a wireless network card that complies with the
IEEE 802.11 standard on wireless LANs (Revision B). The Wireless LAN
Card supports data rates up to 11 Mbit/s.
■ Wi-Fi (Wireless Fidelity) certified by the Wireless Ethernet
Compatibility Alliance (WECA). This means that your Wireless
hardware will communicate with other vendors’ IEEE 802.11
compliant wireless LAN product.
■ Fully compatible with any other wireless LAN system based on Direct
Sequence Spread Spectrum (DSSS) radio technology that complies
with the “IEEE 802.11 standard on wireless LANs (Revision B).
Not all models come with a built in Wireless LAN card.
Wireless LAN cards
The Wireless LAN Card supports the following wireless LAN features:
■ Automatic Transmit Rate Select mechanism in the transmit range of
11, 5.5, 2 and 1 Mbit/s.
■ Frequent Channel Selection (2.4 GHz).
■ Roaming over multiple channels.
■ Card Power Management.
■ Wired Equivalent Privacy (WEP) data encryption, based on the 128 bit
RC4 encryption algorithm as defined in the IEEE 802.11 standard on
wireless LANs.
Satellite P20
xiv
1 Last Saved on 30/05/2003 13:57
User's Manual
Wireless Interoperability
The TOSHIBA Wireless LAN Mini PCI Card products are designed to be
interoperable with any Wireless LAN product that is based on Direct
Sequence Spread Spectrum (DSSS) radio technology, and is compliant
to:
■ The IEEE 802.11 Standard on Wireless LANs (Revision B), as defined
and approved by the Institute of Electrical and Electronics Engineers.
■ The Wireless Fidelity (WiFi) certification as defined by the WECA
Wireless Ethernet Compatibility Alliance.
Wireless LAN and your Health
Wireless LAN products, like other radio devices, emit radio frequency
electromagnetic energy. The level of energy emitted by Wireless LAN
devices however is far much less than the electromagnetic energy
emitted by wireless devices like for example mobile phones.
Because Wireless LAN products operate within the guidelines found in
radio frequency safety standards and recommendations, TOSHIBA
believes Wireless LAN is safe for use by consumers. These standards and
recommendations reflect the consensus of the scientific community and
result from deliberations of panels and committees of scientists who
continually review and interpret the extensive research literature.
In some situations or environments, the use of Wireless LAN may be
restricted by the proprietor of the building or responsible representatives
of the organisation. These situations may for example include:
■ Using the Wireless LAN equipment on board of aeroplanes, or
■ In any other environment where the risk of interference to other
devices or services is perceived or identified as harmful.
If you are uncertain of the policy that applies on the use of wireless
devices in a specific organisation or environment (e.g. airports), you are
encouraged to ask for authorisation to use the Wireless LAN device prior
to turning on the equipment.
Safety Instruction for Wireless Products
If your computer has wireless function, all safety instructions must be
read carefully and must be fully understood, before attempting to use our
Wireless Products.
This manual contains the safety instructions that must be observed in
order to avoid potential hazards that could result in personal injuries or
could damage your Wireless Products.
Satellite P20
xv
1 Last Saved on 30/05/2003 13:57
User's Manual
Limitation of Liability
For damage occurring due to an earthquake or thunder, fire beyond our
responsibility, action by third party, other accident, intentional or
accidental mistakes by a user, misuse, use under abnormal conditions,
we do not take any responsibility.
For incidental damage (loss of business profit, business interruption, etc.)
occurring due to use or disability of the product, we do not take any
responsibility.
For damage occurring due to non observance of the contents described
in the instruction manual, we do not take any responsibility.
For damage occurring due to erroneous operation or hang up caused by
use in combination with products not related to our company, we do not
take any responsibility.
Usage Restrictions
Do not use the Wireless Products for controlling equipment:
■ Equipment directly linked with human life corresponds to the
following.
■ Medical equipment such as life support systems, equipment used
in operations, etc.
■ Exhaust systems for gases such as poisonous gas etc. and
exhaust systems for smoke.
■ Equipment that must be set up in compliance with various laws
such as the Fire Services Act, the Construction Standard Act, etc.
■ Equipment corresponding to that mentioned above.
■ Equipment linked with human safety or having a serious influence on
the safe maintenance of public function, etc., because it is not
designed or manufactured for this type of use.
■ Traffic control equipment for air, railroad, road, marine transport,
etc.
■ Equipment used in atomic power plants etc.
■ Equipment corresponding to that mentioned above.
Satellite P20
xvi
1 Last Saved on 30/05/2003 13:57
User's Manual
WARNING
Turn OFF the Wireless Communication switch of Wireless Products in a
congested place, such as a crowded commuter train.
Keep this product away from a cardiac pacemaker at least 22cm.
Radio waves can potentially affect cardiac pacemaker operation, thereby
causing respiratory troubles.
Turn OFF the Wireless Communication switch inside a medical facility or
near medical electric equipment. Do not bring medical electric equipment
close to the product.
Radio waves can potentially affect medical electric equipment, thereby
causing an accident due to malfunction.
Turn OFF the Wireless Communication switch near an automatic door, fire
alarm or other automatic control equipment.
Radio waves can potentially affect automatic control equipment, thereby
Do not turn ON the Wireless Communication switch in aircraft or in places
that generate or can generate radio interference.
Radio waves can potentially affect them, causing an accident due to
malfunction.
Monitor possible radio interference or other troubles to other equipment
while the product is used. If any effect is caused, turn OFF the Wireless
Communication switch.
Otherwise, radio waves can potentially affect other equipment, thereby
When using the product in a car, check with the automobile dealer if the
car has an adequate electromagnetic compatibility (EMC).
Radio waves of the product can potentially hamper safe driving.
Depending on car model, the product can rarely affect car electronic
equipment if it is used in a car.
NOTE
Do not use the product in the following places:
Places near a microwave oven where a magnetic field generates and
places where static electricity or radio interference generates.
Depending on environment, radio waves can not reach to the product.
Satellite P20
xvii
1 Last Saved on 30/05/2003 13:57
User's Manual
Regulatory Information
The TOSHIBA Wireless LAN Mini PCI Card must be installed and used in
strict accordance with the manufacturer’s instructions as described in the
user documentation that comes with the product. This device complies
with the following radio frequency and safety standards.
Canada – Industry Canada (IC)
This device complies with RSS 210 of Industry Canada.
Operation is subject to the following two conditions: (1) this device may
not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of this device.”
L’utilisation de ce dispositif est autorisée seulement aux conditions
suivantes : (1) il ne doit pas produire de brouillage et (2) l’utilisateur du
dispositif doit étre prét à accepter tout brouillage radioélectrique reçu,
même si ce brouillage est susceptible de compromettre le
fonctionnement du dispositif.
Europe – EU Declaration of Conformity
This device complies with the essential requirements of the R&TTE
Directive 1999/5/EC with essential test suites as per standards:
■ EN 60950 Safety of Information Technology equipment
■ ETS 300 328 Technical requirements for radio equipment
■ ETS 300 826 General EMC requirements for radio equipment.
Satellite P20
xviii
1 Last Saved on 30/05/2003 13:57
User's Manual
Belgium/
België/Belgique
For outdoor usage only channel 10 (2457 MHz)
and 11 (2462 MHz) is allowed.
For private usage outside buildings across public
grounds over less than 300m no special
registration with IBPT/BIPT is required.
Registration to IBPT/BIPT is required for private
usage outside buildings across public grounds
over more than 300m. An IBPT/BIPT license is
required for public usage outside building.
For registration and license please contact
IBPT/BIPT.
Gebruik buiten gebouw alleen op kanalen 10
(2457 MHz) en 11 (2462 MHz). Voor privégebruik buiten gebouw over publieke groud over
afstand kleiner dan 300m geen registratie bij
BIPT/IBPT nodig; voor gebruik over afstand
groter dan 300m is wel registratie bij BIPT/IBPT
nodig. Voor publiek gebruik buiten gebouwen is
licentie van BIPT/IBPT verplicht. Voor registratie
of licentie kunt u contact opnemen met BIPT.
L’utilisation en extérieur est autorisé sur le canal
10 (2457 MHz) et 11 (2462 Mhz).
Dans le cas d’une utilisation privée, à l’extérieur
d’un bâtiment, au-dessus d’un espace public,
aucun enregistrement n’est nécessaire pour une
distance de moins de 300m. Pour une distance
supérieure à 300m un enregistrement auprès de
I’IBPT est requise. Pour une utilisation publique à
I’extérieur de bâtiments, une licence de I’IBPT
est requise. Pour les enregistrements et licences,
veuillez contacter I’IBPT.
Germany/
Deutschland
License required for outdoor installations. Check
with reseller for procedure to follow
Anmeldung im Outdoor-Bereich notwendig, aber
nicht genehmigungspflichtig. Bitte mit Händler
die Vorgehensweise abstimmen.
Satellite P20
xix
1 Last Saved on 30/05/2003 13:57
User's Manual
France
Restricted frequency band: only channels 10 and
11 (2457 MHz and 2462 MHz respectively) may
be used in France. License required for every
installation, indoor and outdoor installations.
Please contact ART for procedure to follow.
Bande de fréquence restreinte : seuls les canaux
10 à 11 (2457 et 2462 MHz respectivement)
doivent être utilisés en France.
Toute utilisation, qu’elle soit intérieure ou
extérieure, est soumise à autorisation. Vous
pouvez contacter I’Autorité de Régulation des
Télécommuniations (http://www.art-telecom.fr)
pour la procédure à suivre.
Italy/Italia
License required for indoor use. Use with
outdoor installations not allowed
E’necessaria la concessione ministeriale anche
per l’uso interno.
Verificare con i rivenditori la procedura da
seguire. L’uso per installazione in esterni non e’
permessa.
Nederland
License required for outdoor installations. Check
with reseller for procedure to follow
Licentie verplicht voor gebruik met
buitenantennes. Neem contact op met verkoper
voor juiste procedure
USA-Federal Communications Commission (FCC)
This device complies with Part 15 of FCC Rules. Operation of the devices
in a Wireless LAN System is subject to the following two conditions:
■ This device may not cause harmful interference.
■ This device must accept any interference that may cause undesired
operation.
TOSHIBA is not responsible for any radio or television interference
caused by unauthorized modification of the devices included with this
TOSHIBA Wireless LAN Mini PCI Card, or the substitution or attachment
of connecting cables and equipment other than specified by TOSHIBA.
The correction of interference caused by such unauthorized modification,
substitution or attachment will be the responsibility of the user.
Satellite P20
xx
1 Last Saved on 30/05/2003 13:57
User's Manual
Caution: Exposure to Radio Frequency Radiation.
The TOSHIBA Wireless LAN Mini PCI Card will be installed with one of
two types of antennas. Both antenna types, when installed are located at
the upper edge of the LCD screen.
For both antennas, the radiated output power of the TOSHIBA Wireless
LAN Mini PCI Card is far below the FCC radio frequency exposure limits.
Nevertheless, the TOSHIBA Wireless LAN Mini PCI Card shall be used in
such a manner that the potential for human contact during normal
operation is minimized. In normal operating configuration, the LCD in the
upright position, the distance between the antenna and the user should
not be less than 20cm.
Refer to the Regulatory Statements as identified in the documentation
that comes with those products for additional information.
Relevant transmitters include FCC IDs: CJ6PA3171WL, CJ6PA3121BT.
Taiwan
Article 14
Unless approved, for any model accredited low
power radio frequency electric machinery, any
company, trader or user shall not change the
frequency, increase the power or change the
features and functions of the original design.
Article 17
Any use of low power radio frequency electric
machinery shall not affect the aviation safety and
interfere with legal communications. In event that
any interference is found, the use of such electric
machinery shall be stopped immediately, and
reusing of such products can be resumed until
no interference occurs after improvement.
The legal communications mentioned in the
above item refer to radio communications
operated in accordance with telecommunication
laws and regulations.
Low power radio frequency electric machinery
shall resist against interference from legal
communications or from industrial, scientific and
medical radio emission electric machinery.
Satellite P20
xxi
1 Last Saved on 30/05/2003 13:57
User's Manual
Using this equipment in Japan
In Japan, the frequency bandwidth of 2,400~2,483.5MHz for second
generation low-power data communication systems such as this
equipment overlaps that of mobile object identification systems (premises
radio station and specified low-power radio station).
1. Sticker
Please put the following sticker on devices incorporating this product.
In the frequency bandwidth of this equipment, industrial device,
scientific device, medical device like microwave oven, licensed
premises radio station and non-licensed specified low-power
radio station for mobile object identification system (RF-ID) that is
used in product line of factories, (Other Radio Stations) are used.
1. Please make sure before using this equipment that no Other
Radio Stations are used in the neighbourhood.
2. In case that RF interference occurs to Other Radio Stations
from this equipment, please change promptly the frequency
for use, place to use, or stop emitting Radio.
3. Please contact TOSHIBA Direct PC if you have a problem,
such as interference from this equipment to Other Radio
Stations.
2. Indication
The indication shown below appears on this equipment.
(1) 2.4 : This equipment uses a frequency of 2.4GHz.
(2) DS : This equipment uses DS-SS modulation.
(3) 4 :
The interference range of this equipment is less than 40m.
:
This equipment uses a frequency bandwidth from
(4)
2,400mhz to 2,483.5MHz.
It is impossible to avoid the band of mobile object
identification systems.
Satellite P20
xxii
1 Last Saved on 30/05/2003 13:57
User's Manual
Device Authorisation
This device obtains the Technical Regulation Conformity Certification and
the Technical Conditions Compliance Approval, and it belongs to the
device class of radio equipment of low-power data communication
system radio station stipulated in the Radio Law and the
Telecommunications Business Law of Japan.
The Name of the radio equipment: MPCI3A-20/R
JAPAN APPROVALS INSTITUTE FOR Approval Number: D01-1128JP
TELECOMMUNICATIONS EQUIPMENT
TELECOM ENGINEERING CENTER
Approval Number: 01NY A1088
The following restrictions apply:
■ Do not disassemble or modify the device.
■ Do not install the embedded wireless module into other device.
Satellite P20
xxiii
1 Last Saved on 30/05/2003 13:57
Contents
Satellite P20
Contents
Introduction............................................................................... xxix
This guide............................................................................................. xxix
Safety icons .......................................................................................... xxx
Service Options .................................................................................... xxx
Chapter 1 Finding Your Way Around.......................................1-1
Making Sure You Have Everything ......................................................1-1
Front With The Display Closed.............................................................1-1
CD/Digital control buttons .................................................................1-2
System status indicators ...................................................................1-3
Left Side .................................................................................................1-5
Right Side...............................................................................................1-6
Rear Side................................................................................................1-7
Bottom Side ...........................................................................................1-9
Front With The Display Open .............................................................1-10
Chapter 2 Getting Started ........................................................2-1
Selecting A Place To Work ...................................................................2-1
Creating a computer-friendly environment ........................................2-1
Keeping yourself comfortable............................................................2-2
Computer placement.........................................................................2-2
Seating and posture ..........................................................................2-2
Lighting ..............................................................................................2-3
Arms and wrists.................................................................................2-3
Work habits .......................................................................................2-4
Other precautions ..............................................................................2-4
Setting Up Your Computer ...................................................................2-5
Connecting the AC adapter ...............................................................2-5
Charging the battery..........................................................................2-6
Connecting A Printer.............................................................................2-7
Connecting A Mouse.............................................................................2-8
Using a USB pointing device.............................................................2-8
User's
SatelliteManual
P20
xxiv
1 Last Saved on 30/05/2003 13:57
Contents
Using The Computer For The First Time .............................................2-9
Turning on the computer ...................................................................2-9
Using the Touch pad .......................................................................2-10
Adjusting brightness ........................................................................2-11
Hotkeys ...........................................................................................2-11
StickyKeys .......................................................................................2-13
Registering your computer ..............................................................2-13
Chapter 3 Learning The Basics ...............................................3-1
Precautions............................................................................................3-1
Computing Tips .....................................................................................3-2
Using The Keyboard..............................................................................3-3
Character keys ..................................................................................3-3
Ctrl, Fn, and Alt keys .........................................................................3-3
Function keys ....................................................................................3-3
Windows® special keys......................................................................3-4
Overlay keys ......................................................................................3-4
Using the overlay to type numeric data .............................................3-4
Using the cursor control overlay........................................................3-5
Starting A Program ...............................................................................3-5
Starting a Program from the Start menu ...........................................3-5
Starting a Program from Windows Explorer ......................................3-5
Starting a Program from the Run Command .....................................3-6
Saving Your Work..................................................................................3-6
File Names.........................................................................................3-6
Printing Your Work................................................................................3-7
Backing Up Your Files ..........................................................................3-7
Copying to a diskette.........................................................................3-7
Working with StickyKeys ......................................................................3-8
Activating StickyKeys ........................................................................3-8
User-Defined Buttons ...........................................................................3-8
The Internet Button and the TOSHIBA Console Button.....................3-8
Configuring the Buttons.....................................................................3-8
Configuring the On Screen Display ...................................................3-9
Using Compact Discs And DVDs .........................................................3-9
The CD-ROM / DVD-ROM / CD-RW/DVD / DVD-R/-RW / DVD
Multi drive ........................................................................................3-10
Playing compact discs ....................................................................3-10
Opening the disc tray with the computer off ...................................3-11
Caring for compact discs and DVDs ...............................................3-11
Using PC Cards ...................................................................................3-11
Inserting PC Cards ..........................................................................3-12
Removing PC Cards ........................................................................3-13
Hot swapping ..................................................................................3-13
Satellite P20
xxv
1 Last Saved on 30/05/2003 13:57
Contents
Using SD Cards ...................................................................................3-14
Using Your Computer As A Desktop Computer ...............................3-16
Using a computer lock.....................................................................3-16
Setting Up Communications ..............................................................3-17
Connecting the modem to a telephone line.....................................3-17
Connecting your computer to a network .........................................3-18
Connecting directly to a remote computer ......................................3-18
Communications parameters ..........................................................3-19
File transfer protocols......................................................................3-19
Turning Off The Computer..................................................................3-20
Caring For Your Computer .................................................................3-20
Cleaning the computer ....................................................................3-20
Moving the computer ......................................................................3-20
Restoring the pre-installed software.................................................3-21
Restoring the complete system .......................................................3-21
TOSHIBA’s Online Resources ............................................................3-21
Chapter 4 Mobile Computing...................................................4-1
TOSHIBA’s Energy-Saving Design.......................................................4-1
Managing Power Usage........................................................................4-1
Running the computer on battery power...........................................4-2
Using additional battery packs ..........................................................4-2
Maximizing battery life.......................................................................4-2
Charging Batteries ................................................................................4-3
Charging the battery..........................................................................4-3
Charging the RTC battery..................................................................4-4
Monitoring Battery Power ....................................................................4-5
Determining remaining battery power ...............................................4-5
Conserving Battery Power....................................................................4-6
What to do when the battery runs low...............................................4-6
Battery Alarms .......................................................................................4-7
Changing The Battery ...........................................................................4-8
Removing the battery ........................................................................4-8
Inserting a battery..............................................................................4-9
Disposing Of Used Batteries Safely.....................................................4-9
Travelling Tips .....................................................................................4-10
Satellite P20
xxvi
1 Last Saved on 30/05/2003 13:57
Contents
Chapter 5 Using Advanced Features ......................................5-1
Multiple Displays ...................................................................................5-1
Adjusting display settings..................................................................5-1
Using multiple displays......................................................................5-1
Setting up more than one display......................................................5-2
Multiple display properties ................................................................5-3
Playing DVDs .........................................................................................5-5
Using a CD-RW, DVD-R/-RW or DVD Multi Drive .............................5-5
About DVD-RAM................................................................................5-5
Playing CDs, DVDs And Digital Music Files With The Computer
On Or Off ................................................................................................5-6
CD Mode ...........................................................................................5-6
Digital Mode ......................................................................................5-7
Using The FIR Port ................................................................................5-7
Using The TOSHIBA Remote Control ..................................................5-8
Using Wireless LAN...............................................................................5-9
Using The TOSHIBA Power Management Utility ..............................5-10
Chapter 6 Expanding & Upgrading..........................................6-1
Using External Peripherals ...................................................................6-1
Connecting A USB Keyboard ...............................................................6-2
Connecting An External USB Pointing Device....................................6-3
Connecting An External Monitor..........................................................6-4
Connecting A Television .......................................................................6-5
Connecting Audio Devices ...................................................................6-6
Connecting external speakers ...........................................................6-6
Connecting A Microphone....................................................................6-7
Connecting A Line-In ............................................................................6-7
Additional Options.................................................................................6-8
External floppy disk drive ..................................................................6-8
Module Bay Options ..........................................................................6-8
Upgrading System Memory..................................................................6-9
Installing additional memory..............................................................6-9
Satellite P20
xxvii
1 Last Saved on 30/05/2003 13:57
Contents
Chapter 7 If Something Goes Wrong ......................................7-1
Problems That Are Easy To Fix ............................................................7-1
Problems When You Turn On The Computer .....................................7-2
Fixing Device-Related Problems..........................................................7-3
Memory module problems ...................................................................7-3
Power Problems ....................................................................................7-4
Keyboard Problems ..............................................................................7-5
Display Problems ..................................................................................7-6
Disk Drive Problems..............................................................................7-7
CD-ROM Drive Problems......................................................................7-9
Sound System Problems ......................................................................7-9
PC Card Problems...............................................................................7-10
Resolving PC Card Problems .............................................................7-10
Printer Problems .................................................................................7-12
Modem Problems ................................................................................7-13
Develop Good Computing Habits ......................................................7-14
If You Need Further Assistance .........................................................7-15
Appendix A Hot Keys ............................................................... A-1
Appendix B Features And Specifications .............................. B-1
Appendix C Power Cable Connectors ...................................C-1
Appendix D Display Modes .....................................................D-1
Appendix E The TOSHIBA International Warranty................ E-1
Appendix F If Your Computer Is Stolen ................................. F-1
Index ........................................................................................... F-1
Satellite P20
xxviii
1 Last Saved on 30/05/2003 13:57
Introduction
Satellite P20
Introduction
Welcome to the world of portable computing. With your new TOSHIBA
Satellite computer, your work can accompany you wherever you go.
Your Satellite P20 computer provides fast and easy Internet access.
Microsoft® Windows® XP is already installed on your computer. It offers
exciting new features and easy Internet access.
This guide
This guide introduces the computer’s features. You can:
■ Read the entire guide from beginning to end.
■ Skim through and stop when a topic interests you.
■ Use the table of contents to find specific information.
If you are new to computers, or have not used a notebook computer
before, read through the first couple of chapters to familiarize yourself
with the parts of the computer and how to turn it on. After that, seek out
whatever interests you most.
Your computer comes with the following documentation:
■ This User’s Guide with information on how the computer works
■ Safety Instruction manual
®
■ Windows XP documentation, which explains the features of the
operating system.
The instructions and pictures in this user’s guide concerning the operating
system are based on Windows® XP. Users of other Windows® operating
systems should remember that the names of some menu items and
procedures may differ from those described in this guide. Please refer to
your operating system documentation if you have any problems.
User's
SatelliteManual
P20
xxix
1 Last Saved on 30/05/2003 13:57
Introduction
Safety icons
This manual contains safety instructions that must be observed in order
to avoid potential hazards that could result in personal injuries, damage to
your equipment, or loss of data. The safety cautions have been classified
according to the seriousness of the risk and the following icons highlight
these instructions as follows:
DANGER: This icon indicates the existence of a hazard that could result in
death or serious bodily injury if the safety instruction is not observed.
WARNING: This icon indicates the existence of a hazard that could result
in bodily injury if the safety instruction is not observed.
CAUTION: This icon indicates the existence of a hazard that could result
in damage to equipment or property if the safety instruction is not
observed.
NOTE: This icon indicates information that relates to the safe operation of
the equipment or related items.
You will also come across the following two icons as you use this guide:
HINT: This icon signals a tip on using your computer.
TECHNICAL NOTE: This icon signals useful information about how your
computer works and tips on, for instance, installing software and devices.
Service Options
TOSHIBA offers a full line of service options built around its warranty
programs. See the warranty and service material included with your
computer for registration information.
If you have a need to contact TOSHIBA, see Appendix E.
Satellite P20
xxx
1 Last Saved on 30/05/2003 13:57
Finding Your Way Around
Satellite P20
Chapter 1
This chapter presents a grand tour of your Satellite computer which
serves as a reference when you need to locate specific parts of the
computer. You will find more detailed information on using these parts in
later chapters.
Making Sure You Have Everything
Before doing anything else make sure you received everything. If any
items are missing or damaged, notify your dealer immediately.
Front With The Display Closed
CD/DIGITAL MODE
BUTTON
2ND MODULE BAY
DISPLAY LATCH
REMOTE CONTROL
RECEIVER
MAIN MODULE BAY
The Display Latch keeps the display panel closed and locked. To open
the computer, slide the display latch to the right and then lift the display
panel.
The CD/Digital Mode Button allows you to select and play music from
audio CDs or digital files using the control buttons even when the
computer is turned off.
The Remote Control Receiver is the infrared port used by for the
TOSHIBA Remote Control. (The Remote Control device is not supplied
with all models.)
User's
Manual
User's Manual
1-1
1-1
1 Last Saved on 30/05/2003 13:57
The Main Module Bay allows you to play CDs and DVDs. Your computer
is fitted with either a CD or DVD drive installed, depending on its
configuration. You may also be able to write CDs or even DVDs. A
secondary HDD or FDD may also be used in this bay.
The 2nd Module Bay is generally used for the removable battery, but it
may also be used with a second Optical Media Drive.
You can purchase TOSHIBA optional HDD and optical devices in order to
extend computer's function. Please get contact with your TOSHIBA
dealer.
CD/Digital control buttons
CD/DIGITAL MODE
BUTTON
PREVIOUS
NEXT
CD MODE INDICATOR
LED
DIGITAL MODE
INDICATOR LED
STOP/EJECT
PLAY/PAUSE
The CD/Digital Mode button sets which audio playback mode to use,
either audio CD or digital music file such as MP3 or Windows Media Files.
Whether your computer is turned on or off, the CD/Digital control buttons
are locked by default. To unlock them, press the CD/Digital mode button
for more than 3 seconds. Press the CD/ Digital mode button again for over
3 seconds to lock them again. When the CD/Digital mode is unlocked,
press the CD/Digital Mode briefly to switch between CD and Digital mode.
The mode indicator LEDs will tell you which mode you are in.
The other CD/Digital Control buttons function like an audio CD player’s
controls and have the following functions:
Next
Skips to the following track on the disc
Previous
Returns to the preceding track.
Stop/Eject
Stops a track that is currently playing and ejects
a stopped disc.
Play/Pause
Starts playing the disc or the selected digital
track, or pauses the track that is currently
playing.
User's Manual
1-2
1 Last Saved on 30/05/2003 13:57
Full instructions on playing CDs, DVDs and digital music files with your
computer on or off are given in chapter 5.The Eject button works in
system off mode.
System status indicators
POWER
DC-IN
BATTERY
The DC-IN LED indicates the computer is connected to the AC adapter
and it is plugged into an AC power source.
The Power LED flashes amber while the system is in Standby mode. The
LED turns off when the computer is turned off or in hibernation mode.
The Battery LED indicates the battery’s current charge/ discharge status.
It lights green when the battery is fully charged. It lights amber while the
battery is being charged from the AC adapter. It flashes amber when the
battery capacity is low.
User's Manual
1-3
1 Last Saved on 30/05/2003 14:41
MAIN HARD DRIVE
MODULE BAY
SD CARD
WIRELESS
COMMUNICATION
The Main Hard Drive LED indicates that the HDD is being accessed.
Every time your computer runs a program, opens a file, or performs some
other function in which it must access the HDD, this light goes on.
The Module Bay LED indicates that the device in either the Main or 2nd
Module Bay is being accessed.
The SD Card LED indicates the computer is accessing data from an SD
Card.
The Wireless Communication LED indicates the wireless LAN or
Bluetooth feature is active and that you may connect to a Local Area
Network.
Not all models come fitted with a wireless communication or Blutetooth
device
User's Manual
1-4
1 Last Saved on 30/05/2003 13:57
Left Side
WIRELESS
COMMUNICATION
SWITCH
LINE-IN JACK
HEADPHONE JACK
SECURITY LOCK SLOT
MICROPHONE JACK
VOLUME CONTROL
The Volume Control adjusts the audio volume level.
The Microphone Jack let you connect a 3.5mm three conductor mini
jack microphone or other audio input device.
The Headphone Jack lets you connect stereo headphones or other
audio-output devices such as external speakers. Connecting headphones
or other devices to this jack automatically disables the internal speakers.
The Line-In Jack is a standard 3.5 mm mini line-in jack that enables
connection of a stereo device for audio input.
Not all models come fitted with a wireless communication or Blutetooth
device
The Wireless Communication Switch (for Wireless LAN or Bluetooth)
turns on the wireless networking transceiver. An indicator LED on the left
of the keyboard lights to indicate that wireless networking is turned on.
Not all models will come with wireless LAN device or Bluetooth.
The Security Lock Slot allows you to secure your computer with a cable
lock to a desk or some other object to prevent theft.
User's Manual
1-5
1 Last Saved on 30/05/2003 13:57
Right Side
USB PORTS
MODEM JACK
SD CARD SLOT
FIR PORT
I.LINK Port
PC Card Slots
TV Out Port
The i.LINK (IEEE 1394) Port lets you connect devices such as digital
video cameras to your computer in order to download data from them.
The i.LINK Port is not available on all configurations.
The USB (Universal Serial Bus) Ports allow you to connect USB
peripherals to the computer, such as a full-size USB keyboard or a USB
pointing device. There are two more USB ports on the rear of your
computer.
The Modem Jack lets you connect to a standard telephone line through
a Modem cable.
The two-stacked CardBus-ready PCMCIA-compatible PC Card Slots
allow you to install additional devices. Each slot can accommodate one
Type II PC Card. Both slots are able to install one Type III PC Card.
Keep foreign objects out of the PC Card slots. A staple or similar object
that accidentally gets into a slot can damage the computer’s circuitry.
The FIR (Fast Infrared) Port is a fast infrared communication port that
allows the computer system to communicate with other IR-equipped
devices.
The FIR Port is not available on all models.
The TV Out Port allows you to connect to a television or TV monitor with
a 4-pin S-video cable.
The SD Card Slot allows you to use install and use SD media disks, such
as the kind found in digital cameras, on your computer.
User's Manual
1-6
1 Last Saved on 30/05/2003 13:57
Rear Side
PARALLEL PORT
EXTERNAL MONITOR
PORT
LAN JACK
USB PORTS
FAN VENTS
DC-IN
The LAN Jack is an RJ-45 jack for using a standard LAN cable to
connect to a Local Area Network.
ACTIVITY (AMBER
LIGHT
LINK (GREEN LIGHT)
There are two status indicator on the LAN Jack. The right indicator turns
green when the LAN Jack is linked with the cable, and the left one flashes
amber when the LAN is active.
User's Manual
1-7
1 Last Saved on 30/05/2003 13:57
The Parallel Port lets you connect a parallel printer, or other devices
including ECP-compatible devices.
The two USB (Universal Serial Bus) Ports allow you to connect USB
peripherals to your computer, such as a printer, keyboard or pointing
device. There are two more USB ports on the right side of your computer.
USB 2.0 is a peripheral expansion standard that supports a data- transfer
rate of up to 480 Mbps. USB peripherals have a single standard for cables
and connectors. The USB standard allows you to install and remove USB
devices while the computer is on. Switching devices without turning off
the computer is called “Hot swapping.”
The External Monitor Port is a standard 15-pin VGA port for connecting
an analog display such as a desktop computer monitor.
The DC-IN is where you plug in the AC adapter.
The Fan Vents help cool the computer by letting the internal fans shed
heat more easily.
To prevent possible overheating of the CPU, never block the fan vents.
User's Manual
1-8
1 Last Saved on 30/05/2003 13:57
Bottom Side
MAIN MODULE BAY
LOCK
BLUETOOTH/MODEM
MODULE COVER
FAN COVER
2ND MODULE BAY
LOCK
MAIN MODULE BAY
LATCH
WIRELESS LAN CARD
MODULE COVER
MEMORY MODULE
COVER
2ND MODULE BAY
LATCH
The Memory Module Cover protects the system memory modules.
The Bluetooth/Modem Module Cover protects the Bluetooth device (if
installed; some configurations may not have it) and the internal modem.
The Wireless LAN Card Module Cover protects the Wireless LAN Card
(some configurations may not have it.)
The two Module Locks secure the modules in the Main and 2nd Module
bays, preventing them from accidentally falling out if the release latches
are inadvertently pressed.
The two Module Release Latches disconnect the modules from their
bays. To remove the Main Module, place the closed computer upside
down with its front toward you. Unlock the Module Bay lock on the Main
Module Bay side, slide on the latch on the Main Module Bay side and
then slide it toward the outside edge of the computer. Remove the
module from its bay. Follow the same steps for the 2nd Module.
User's Manual
1-9
1 Last Saved on 30/05/2003 13:57
Always keep the Module Bay locks secured while the modules are in their
bays.
Never remove or insert a module without first shutting down the
computer. Doing so could result in irreparable damage.
Never cover the fan inlets.
Front With The Display Open
POWER BUTTON
LCD SCREEN
KEYBOARD
TOUCH PAD
INTERNET BUTTON
TOSHIBA CONSOLE
BUTTON
TV OUT BUTTON
The LCD Screen is the computer’s primary display. Your computer is
equipped with a 17” TFT screen with WXGA (1440 x 900) resolution.
TFT (Thin Film Transistor) is a type of LCD flat panel display screen in
which each pixel is controlled by from one to four transistors. Screens
with TFT technology (sometimes called active-matrix LCDs) provide better
resolution than other types of flat-panel LCD displays.
User's Manual
1-10
1 Last Saved on 30/05/2003 13:57
The Power Button turns the computer on and off, or let the system enter
lower power mode (Standby, Hibernation) depending on power
management setting.
The Keyboard provides all the functionality of a full-size keyboard.
The front panel provides a palm rest to assist you in maintaining proper
posture while using the computer.
The keyboard function keys, when used with the Fn key, activate various
system functions, such as the LCD brightness control.
See chapter 3 and appendix A for more information.
The Caps Lock LED lights when you press the Caps Lock key. When this
light is on, pressing a letter key on the keyboard produces an uppercase
(capital) letter.
The Cursor Lock LED lights when the arrow control overlay is turned on
by pressing the Fn and F10 keys simultaneously. When this light is on,
pressing an overlay key moves the cursor in the direction of the reddish
white arrow printed on the left front of the key instead of the letter printed
on the key.
The Num Lock LED lights when the numeric keypad overlay is turned on
by pressing the Fn and F11 keys simultaneously. When this light is on,
pressing an overlay key displays the number printed on the right front of
the key instead of the letter printed on the top of the key.
The Cursor Lock and Num Lock cannot be used at the same time.
User's Manual
1-11
1 Last Saved on 30/05/2003 13:57
TOUCH PAD
TOUCH PAD CONTROL
BUTTONS
The Touch pad is a pressure sensitive pointing device which works like a
mouse to position the cursor on the screen.
The two Touch pad Control Buttons have essentially the same functions
as mouse buttons. See chapter 2 for further information.
User's Manual
1-12
1 Last Saved on 30/05/2003 13:57
INTERNET BUTTON
TV OUT BUTTON
TOSHIBA CONSOLE
BUTTON
The two User-Defined buttons are pre-configured as the Internet
button, which opens your default web browser, and the TOSHIBA
Console button, which opens the TOSHIBA Console program. Both can
be assigned custom tasks, which are then triggered when one of them is
pressed. The third button is for TV Out.
User's Manual
1-13
1 Last Saved on 30/05/2003 13:57
Getting Started
Satellite P20
Chapter 2
Getting Started
This chapter provides tips for working comfortably, describes how to
connect components, and explains what to do the first time you use your
notebook computer.
Selecting A Place To Work
Your computer is portable and designed to be used in a variety of
circumstances and locations.
Creating a computer-friendly environment
Place the computer on a flat surface, which is large enough for the
computer and any other items you need to use, such as a printer. Leave
enough space around the computer and other equipment to provide
adequate ventilation and prevent overheating.
To keep your computer in prime operating condition, protect your work
area from:
■ Dust, moisture, and direct sunlight.
■ Liquids and corrosive chemicals.
If you spill liquid into the computer, turn it off, unplug it from the AC
power source, remove the battery, and let it dry out completely before
turning it on again. If the computer does not operate correctly after you
turn it back on, contact a TOSHIBA authorized service provider.
■ Equipment that generates a strong electromagnetic field, such as
stereo speakers (other than speakers that are connected to the
computer) or speakerphones.
■ Rapid changes in temperature or humidity and sources of temperature
change such as air conditioner vents or heaters.
■ Extreme heat, cold, or humidity. Use the computer within a
temperature range of 5° to 35° C (40° to 95° Fahrenheit) and 20% to
80% non-condensing humidity.
User's
Manual
User's Manual
2-1
2-1
1 Last Saved on 30/05/2003 13:57
Getting Started
Keeping yourself comfortable
Strain and stress injuries are becoming more common as people spend
more time using their computers. However, with a little care and proper
use of the equipment, you can work comfortably throughout the day.
This section provides hints on avoiding strain and stress injuries. For
more information, consult books on ergonomics, repetitive- strain injury,
and repetitive-stress syndrome.
Computer placement
Proper placement of the computer and external devices is important to
avoid stress-related injuries.
■ Place the computer on a flat surface at a comfortable height and
distance. You should be able to type without twisting your torso or
neck, and look at the screen without slouching.
■ If you are using an external monitor, the top of the display should be
no higher than eye level.
■ If you use a paper holder, set it at about the same height and distance
as the screen.
Seating and posture
When using your computer, maintain good posture with your body
relaxed and your weight distributed evenly. Proper seating is a primary
factor in reducing work strain. Some people find a backless chair more
comfortable than a conventional chair.
90
1
Correct posture and positioning of the computer
Whichever type you choose, use the following guidelines to adjust your
chair for maximum computing comfort.
■ Position your chair so that the keyboard is at or slightly below the level
of your elbow. You should be able to type comfortably with your
shoulders relaxed and your forearms parallel to the floor.
User's Manual
2-2
1 Last Saved on 30/05/2003 13:57
Getting Started
If you are using a conventional chair:
■ Your knees should be slightly higher than your hips. If necessary, use
a footrest to raise the level of your knees and ease the pressure on the
back of your thighs.
■ Adjust the back of your chair so that it supports the lower curve of
your spine. If necessary, use a cushion to provide extra back support.
Lower-back-support cushions are available at many office supply
stores.
■ Sit with your back straight so that your knees, hips, and elbows form
approximately 90-degree angles when you work. Do not slump
forward or lean back too far.
Lighting
Proper lighting can improve the visibility of the display and reduce
eyestrain.
■ Position the display panel or external monitor so that sunlight or bright
indoor lighting does not reflect off the screen. Use tinted windows or
shades to reduce glare.
■ Avoid placing your computer in front of a bright light that could shine
directly in your eyes.
■ If possible, use soft, indirect lighting in your computer work area.
Arms and wrists
■ Avoid bending, arching, or twisting your wrists. Keep them in a
relaxed, neutral position while typing.
■ Exercise your hands, wrists, and arms to improve circulation.
Using the computer keyboard incorrectly may result in discomfort and
possible injury. If your hands, wrists, and/or arms bother you while typing,
stop using the computer and rest. If the discomfort persists, consult a
physician.
User's Manual
2-3
1 Last Saved on 30/05/2003 13:57
Getting Started
Work habits
The key to avoiding discomfort or injury from strain is to vary your
activities. If possible, schedule a variety of tasks into your working day.
Finding ways to break up the routine can reduce stress and improve your
efficiency.
■ Take frequent breaks to change position, stretch your muscles, and
relieve your eyes. A break of two or three minutes every half hour is
more effective than a long break after several hours.
■ Avoid performing repetitive activities for long periods. Intersperse
such activities with other tasks.
■ Focusing your eyes on your computer screen for long periods can
cause eyestrain. Look away from the computer frequently and focus
your eyes on a distant object for at least 30 minutes.
Other precautions
Your Satellite computer is designed to optimise safety, minimize strain,
and withstand the rigors of portability. However, you should observe
certain precautions to further reduce the risk of personal injury or damage
to the computer.
Avoid prolonged physical contact with the underside of the computer. If
the computer is used for long periods, its case can become very warm.
While the temperature may not feel too hot to the touch, if you maintain
physical contact with the computer for a long time (if you rest the
computer on your lap, for example), your skin might suffer low-heat injury.
Never apply heavy pressure to the computer or subject it to sharp shocks.
Excessive pressure or shock can damage computer components or
otherwise cause your computer to malfunction. Some PC Cards can
become hot with prolonged use. If two cards are installed, both can
become hot even if only one is being used. Overheating of a PC Card can
result in errors or instability in its operation. Be careful when you remove a
PC Card that has been used for a long period.
User's Manual
2-4
1 Last Saved on 30/05/2003 13:57
Getting Started
Setting Up Your Computer
Setting up your computer may include:
■ Connecting the AC adapter
■ Charging the battery
■ Connecting a printer
■ Connecting an alternate pointing device
Connecting the AC adapter
Your computer contains a rechargeable battery pack, which needs to be
charged before you can use it the first time.
The AC adapter enables you to power the computer from an AC outlet
and to charge the computer’s battery.
Used with the AC adapter, your Satellite computer can run on power
supplies worldwide.
To connect AC power to the computer:
1. Connect the power cable to the AC adapter.
User's Manual
2-5
1 Last Saved on 30/05/2003 13:57
Getting Started
2. Plug the AC adapter into the computer’s DC-IN.
DC IN
3. Connect the power cable to an AC power outlet.
If the battery is being charged, the Battery LED on the system indicator
panel on the front of your computer will light amber. Once the battery is
fully charged the battery light turns green.
The surface of the adapter’s plastic housing may get hot as it is operating.
Do not touch the plastic surface when the adapter is operating to prevent
possible hazard.
To avoid electric shock, do not modify, forcibly bend, damage, place
heavy objects on top of, or apply any chemical treatments to the power
cable. If the power cable becomes damaged or the plug overheats,
discontinue use. Never remove the power plug from the outlet with wet
hands.
Using the wrong AC adapter could damage your computer. TOSHIBA
assumes no liability for any damage in such cases. Never pull directly on
the power cable to unplug it. Hold the power plug when removing the
cable from the outlet.
Charging the battery
Before you can use the battery to power the computer, you must charge
it. Connect the computer to an AC power outlet using the AC adapter and
power cable. The DC-IN LED on the system indicator panel on the front of
the computer will light and the Battery LED will light amber. Once the
battery is fully charged the Battery LED turns green.
Once the computer is connected to a power outlet, you can charge the
battery with the computer turned off or on. When the computer is turned
off, the battery charges in about 4 hours.
The battery will take considerably longer to charge (up to 12 hours or
longer) if the computer is turned on and consuming a lot of power.
Once the battery is charged for the first time, avoid leaving the computer
plugged in and turned off for more than a few hours at a time. Continuing
to charge a fully charged battery may impact the battery.
For more information on running your computer using the battery and on
maximizing the life of your battery, turn to chapter 4.
User's Manual
2-6
1 Last Saved on 30/05/2003 13:57
Getting Started
Connecting A Printer
Before connecting a printer, you need to know whether it requires a USB
or a parallel interface. Check the printer’s documentation. If the printer
can be switched between USB and parallel mode, choose parallel if you
want to leave your USB ports free for other use.
You also need a suitable printer cable which may come with your printer.
If not, you can purchase one from a computer or electronics store.
Connecting the printer cable while the computer is on may damage the
printer, the computer, or both.
If your printer is ECP or IEEE-compliant, make sure your printer cable is an
IEEE-1284 cable.
The following instructions assume you have a printer that uses a parallel
port connection, which is the most common type of printer interface.
1. Turn off the computer.
2. Connect the printer cable to the printer and to the computer’s parallel
port.
3. Plug the printer’s power cable into an AC outlet.
4. Refer to your printer documentation for additional configuration steps.
PARALLEL PORT
User's Manual
2-7
1 Last Saved on 30/05/2003 13:57
Getting Started
Connecting A Mouse
You may want to use a external mouse or trackball instead of the
computer’s built-in Touch pad pointing device. Your Satellite computer
supports USB-compatible pointing devices.
The Touch pad remains operable even if you connect an external pointing
device to the computer.
Using a USB pointing device
1. Plug the device into one of the USB ports on the computer. We
recommend right-handed users attach the device to the USB port on
the right-hand side of the computer; left-handed users may find it
more convenient to use one of the USB ports on the rear.
RIGHT USB PORTS
REAR USB PORTS
2. The device will probably require a driver and possibly other software;
install it according to the instructions that come with it.
3. Position the device where you want to use it.
You don’t have to turn off the computer to connect or disconnect USB
devices.
User's Manual
2-8
1 Last Saved on 30/05/2003 13:57
Getting Started
Using The Computer For The First Time
Slide the display panel latch to the right to release it and then lift the
display panel to open the computer.
Don’t force the display panel open beyond the point where it moves
easily. Never lift or move the computer by grasping the display panel.
Turning on the computer
1. Make sure that the Optical Media Drive or FDD drive is empty.
2. Open the display panel.
3. If you have a printer connected to your computer, turn the printer on
and wait until it indicates it is ready.
4. Turn on the computer by momentarily pressing then releasing the
power button.
When you release the power button, the Power LED on the system
indicator panel comes on.
When turning on the computer for the first time, don’t turn it off until the
operating system has loaded completely. Turning off the computer during
its initial startup will cause an error the next time you start the computer.
For more on turning off your computer safely, turn to chapter 3.
When the computer is connected to an external power source, the DC-IN
LED lights. If the battery is being charged, the Battery LED lights amber.
The Hard Drive LED flashes when the hard disk drive is accessed.
To avoid data loss, never turn off the computer while a drive is in use.
User's Manual
2-9
1 Last Saved on 30/05/2003 13:57
Getting Started
Using the Touch pad
The Touch pad is a touch-sensitive pointing device that provides all the
features of a mouse. Please refer to the following instructions on how to
operate the Touch pad.
The Touch pad is easily accessible by moving any of your fingers off the
space bar and onto the Touch pad.
Gently move your finger across the Touch pad in the direction you want
the cursor to move. The pad detects the change in pressure and moves
the cursor in the corresponding direction.
With a conventional mouse, selections are usually made by double
clicking the mouse’s left button. The Touch pad also supports this
feature. It is described in detail below. If you are familiar with the
operations of a mouse you may only need to skim the information below.
The Touch pad buttons have essentially the same function as mouse
buttons. Clicking these buttons makes selections, drags object, or
performs a variety of other functions depending on the software. To
select an object, first move the pointer to the object you want to select,
and then press the left button one time and release it. The functionality of
these buttons depends on your software. Refer to your software user’s
manuals for specific information on the Touch pad (mouse) functions.
Double clicking is a common technique for selecting objects or launching
programs from icons. Move the pointer over the object you wish to select,
then rapidly press the left button two times. This action is commonly
referred to as “double clicking on an object.”
Double tapping is another technique for selecting objects or executing
applications from icons. For the most part double tapping is very similar
to the double clicking technique of a mouse. The difference is that instead
of double clicking on a mouse button, you double tap on the pressure
sensitive Touch pad to make the selection. Once the cursor has been
moved over the object you want select, lightly double tap the Touch pad
itself. The double tapping will select the desired item and prompt the
software to perform the related operation.
User's Manual
2-10
1 Last Saved on 30/05/2003 13:57
Getting Started
Many of the functions within Microsoft Windows® series operating
systems can also be launched by using single tap on the Touch pad. This
single tapping will select the desired item and prompt the software to
perform the related operation.
When working with programs that employ a graphical user interface (GUI),
such as Windows®, dragging objects from one point on the screen to
another is a technique you will have to master. To drag an object, first
move the pointer over the object, then press and hold down the left
button. Now without releasing the button, move the object to a new
location on the screen by moving your finger across the Touch pad. Once
the object is in the desired position, release the button to drop the object
in place.
You can change settings for the Touch pad - such as how quickly you
need to click twice for the computer to recognize a ‘double-click’. Go to
Start, Control Panel, then (in traditional view) Mouse.
Adjusting brightness
Use the following hot key combinations to adjust the screen brightness
and perform other basic functions:
Hotkeys
For a full list of hot keys turn to Appendix A.
Sound Mute
Turns sounds on and off.
Instant password
security
Enters screen saver mode and blanks the
screen. To restore your desktop, press any key
or use the Touch pad.
Power Save Modes
This hot key displays the power save modes.
Standby
When you press Fn + F3, the computer can
enter Standby mode.
Hibernate
When you press Fn + F4 the computer can enter
Hibernate mode.
Display Selection
Press Fn + F5 to change the active display
device. When you press these hot keys a dialog
box appears. Only selectable devices will be
displayed.
Brightness down
Pressing Fn + F6 decreases the display
brightness.
User's Manual
2-11
1 Last Saved on 30/05/2003 13:57
Getting Started
Brightness up
Pressing Fn + F7 increase the display
brightness.
Switch Wireless LAN
function on and off
For the Hot Key to function, the master Wireless
Communication switch must be turned to “on”.
Check the Wireless communication LED on the
system status indicator panel to confirm whether
wireless communication is on or off.
Your computer may not have this function,
depending on the model bought.
Touch pad On/Off
Pressing Fn + F9 enables or disables the
Touch pad function. When you press these
hotkeys, the current setting will change and be
displayed as an icon.
Cursor keypad on/off This hot key enables/ disables the embedded
cursor keypad. Numeric lock state is logically
disabled. See chapter 3 for more information.
Numeric keypad
on/off
This hot key enables/ disables the embedded
numeric keypad. Numeric lock state is logically
enabled. See chapter 3 for more information.
Scroll Lock on/off
Change Resolution
Changes the current screen resolution.
Brightness control with Fn+F6 or Fn+F7 is temporary. After the computer
restarts, the brightness setting in the TOSHIBA Power Management Utility
overrides it. For more on the TOSHIBA Power Management Utility, refer to
chapter 5.
After the computer is restarted, the cursor keypad and numeric keypad
are both turned off on the notebook keyboard.
If no screen image appears after switching displays, press the
Fn + Spacebar combination again to change resolution
User's Manual
2-12
1 Last Saved on 30/05/2003 13:57
Getting Started
StickyKeys
StickyKeys is the primary keyboard accessibility option. It allows the user
to access Shift, Ctrl and Alt key combinations by pressing keys one after
the other rather than simultaneously. For instance the Ctrl-A combination
can be accessed by pressing the Ctrl key followed by the A key. You can
adjust the settings for StickyKeys by clicking on Start, then Control
Panel, then Accessibility. Select the Keyboard tab. Fn key also supports
StickyKey function.
Registering your computer
Registering your computer lets TOSHIBA keep you up-to-date with
information about new products and upgrades, and also provides
TOSHIBA warranty coverage. See the registration card and warranty
information in the appendix section for details about the warranty options
available from TOSHIBA.
User's Manual
2-13
1 Last Saved on 30/05/2003 13:57
Learning The Basics
Satellite P20
Chapter 3
Learning The Basics
This chapter covers precautions and computing tips that you should
follow when using your Satellite series computer. It also provides
important information about the basic features of your system.
Precautions
■ Don’t spill liquids onto the computer’s keyboard.
If you do spill a liquid that gets into the keyboard, turn off the
computer immediately. Leave the computer turned off overnight to let
it dry out before you use it again.
■ Don’t turn off the computer if a drive light indicates a drive is active.
Turning off the computer while it is reading from or writing to a disk
may damage the disk, the drive, or both.
■ Keep the computer and disks away from objects that generate strong
magnetic fields, such as large stereo speakers.
Information on disks is stored magnetically. Placing a magnet too
close to a disk can erase important files.
Always use the Standby or Hibernate mode to power down your
computer. Important files may be damaged if the computer is turned off
without using the Turn Off Computer command.
Before using the Standby or Hibernate mode to power down your
computer, save your files and mark sure the disk activity lights are off.
■ Scan all new files for viruses.
This precaution is especially important for files you receive via
diskette, email, or download from the Internet. Occasionally, even new
programs you buy from a supplier may contain a computer virus.
You’ll need a special program to check for viruses. Ask your dealer to
help you.
User's
Manual
User's Manual
3-1
3-1
1 Last Saved on 30/05/2003 13:57
Learning The Basics
Computing Tips
■ Save your work frequently.
Your work stays in the computer’s temporary memory until you save it
to the disk. You will lose all the work done since you last saved, if, for
example, a system error occurs and you must restart your computer,
or your battery runs out of charge while you are working.
Some programs have an automatic save feature which you can turn on.
This feature saves your file to the hard disk at preset intervals. See your
software documentation for details.
■ Back up your files to floppy disks (or other removable media) on a
regular basis. Label the backup copies clearly and store them in a
safe place.
It is easy to put off backing up because it takes time. However, if your
hard disk suddenly fails, you may lose all the data on it unless you
have a separate backup copy.
■ Use Error-checking and the Disk Defragmenter regularly to conserve
disk space and help your computer perform at its optimal level.
To run Error-checking:
1. Click Start and open My Computer.
2. Click the drive you want to test.
3. On the File menu, click Properties.
4. On the Tools tab, under Error-checking, click Check Now.
5. Under Check disk options, select the Scan for and attempt
recovery of bad sectors check box.
To run Disk Defragmenter, click Start, point to All Programs,
Accessories, System Tools, and click Disk Defragmenter.
®
Consult your Microsoft operating system documentation for more
information on these and other utilities.
■ Take frequent breaks to avoid repetitive-motion injuries and eye strain.
■ Before turning off the computer, always use the Turn Off Computer
command.
User's Manual
3-2
1 Last Saved on 30/05/2003 13:57
Learning The Basics
Using The Keyboard
Character keys
Typing with the character keys is very much like typing on a typewriter,
except that:
■ The space bar creates a space character instead of just passing over
an area of the page.
■ The lowercase letter I and the number 1 are not interchangeable.
■ The uppercase letter O and the number 0 are not interchangeable.
The Caps Lock key shifts the letter keys to upper case – the number
and symbol keys are not affected. The Caps Lock LED on the
keyboard illuminates when you press Caps Lock.
Ctrl, Fn, and Alt keys
The Ctrl, Fn, and Alt keys do different things depending on the program
you are using. For more information, see your program documentation.
Function keys
The function keys (not to be confused with the Fn key) are the 12 keys at
the top of the keyboard.
F1 through F12 are called function keys because they perform
programmed functions when pressed. Used in combination with the Fn
key, function keys marked with icons execute specific functions, such as
dimming the computer display and enabling the numeric keypad. See
appendix A for more details of these ‘hot key’ functions.
User's Manual
3-3
1 Last Saved on 30/05/2003 13:57
Learning The Basics
®
Windows special keys
WINDOWS® KEY
APPLICATION KEY
The keyboard provides two keys that have special functions in Windows®.
The Windows® key activates the Start menu. The Application key has the
same function as the secondary (normally right-side) mouse (or Touch
pad) button.
Overlay keys
The keys with numbers and symbols on the front of them form the
numeric and cursor overlay. This overlay lets you enter numeric data or
control the cursor as you would use the ten-key keypad on a desktop
computer’s keyboard.
Using the overlay to type numeric data
To turn the numeric overlay on and off, press Fn and F11 simultaneously.
The numeric mode light immediately below the F11 key glows when the
numeric overlay is on.
You can still use the overlay keys to type alphabetic characters while the
numeric overlay is on.
■ For lowercase letters, hold down Fn while you type the letters.
■ For uppercase letters, hold down both Fn and Shift while you type the
letters.
To use the cursor control keys (allowing you to move the cursor up,
down, left and right using the keyboard) when the numeric overlay is on,
press and hold down Shift while you use the cursor control keys To
return to the numeric overlay, release Shift.
User's Manual
3-4
1 Last Saved on 30/05/2003 13:57
Learning The Basics
Using the cursor control overlay
To turn the cursor control overlay on and off, press Fn and F10
simultaneously. The cursor control light immediately below the F10 key
glows when the cursor control overlay is on.
To type alphabetic characters while the overlay is on:
■ For lowercase letters, hold down Fn while you type the letters.
■ For uppercase letters, hold down both Fn and Shift while you type the
letters.
To highlight text with the cursor control overlay on, hold down Shift while
you use the cursor control keys.
Starting A Program
There are three ways to start a program in Microsoft® Windows® series
operating systems: from the Start menu, from Windows Explorer, or from
the Run command in the Start menu.
Starting a Program from the Start menu
1. Click Start, then point to All Programs.
®
®
Microsoft Windows XP operating system displays the Program
menu, which lists programs and program groups, If your program is
listed, go to step 3; otherwise, continue with step 2.
2. Point to the program group containing the program that you want to
start.
Microsoft® Windows® XP operating system displays the associated
program menu.
3. Click the program’s icon to start the program.
To close the program, click the Close button at the upper-right corner of
the program’s window.
Starting a Program from Windows Explorer
If a program is not in the Programs menu, you can start it from Windows
Explorer. Windows Explorer gives you a view of your computer’s contents
as a hierarchy or “tree.” You can easily see the contents of each drive
and folder on your computer. To use this method, you need to know the
name and location of the program’s executable file (this file ends with
“.exe”.)
1. Click Start, point to All Programs, then point to Accessories, and
then click Windows Explorer.
■ The left side of the window displays the disk drives and folders on
your computer.
■ The right side of the window displays the contents of the item you
click on the left.
2. To open a document or start a program, double-click its icon in the
right side of the window.
User's Manual
3-5
1 Last Saved on 30/05/2003 13:57
Learning The Basics
Starting a Program from the Run Command
You can start a program from the taskbar if you know its name and
location.
1. Click Start on the taskbar.
2. Click Run.
3. In the dialog box, type the command line.
4. Click OK.
Saving Your Work
Before you turn off the computer, save your work to the hard disk drive.
This is one of the most important rules of computing.
Save your data even when you are using Standby, in case the battery
discharges before you return to work.
Many programs offer a feature that saves documents at regular intervals,
such as every 15 minutes. Check your program’s documentation to see
whether it has an automatic save feature.
■ To save a file you are updating, open the program’s File menu and
click Save (a common shortcut for this in many programs is to press
the Ctrl key and the ‘S’ key together). Save your work at regular
intervals as you work.
■ To save the current file with a new name, choose Save As from the
File menu, type a name for the file, choose a location to save it and
click OK.
To make another copy of the file you are currently working with, choose
Save As from the File menu and give the new file a different name.
File Names
Microsoft® Windows® XP operating system supports file names of up to
255 characters. You may use all the letters and numbers on the keyboard
plus the following characters: _, ^, $, ~, !, #, %, &, {, }, (, ), @, [, ], +, -, ;,
and ’. The names can include spaces.
If you plan to share your files with a computer using MS-DOS® or a preWindows® 95 version of Windows®, the file name must be no more than
eight characters followed by a period and a three character extension. An
MS-DOS file name may not contain a space.
Most programs assign an extension that identifies the file as having a
particular format. For example, Microsoft® Word saves files with a .doc
extension.
User's Manual
3-6
1 Last Saved on 30/05/2003 13:57
Learning The Basics
Printing Your Work
Make sure that the Microsoft® Windows® XP operating system is set up
for your printer.
You only need to setup the printer the first time you connect it. If you use
more than one printer or are changing printers, you will need to setup your
®
®
Microsoft Windows operating system to run with the additional printer(s).
1. If your printer is not on, turn it on now.
®
2. In the File menu of your Windows program, click Print.
The program displays a Print dialog box similar to the one below.
3. Click the Print button.
Backing Up Your Files
Backing up your files simply means copying individual files to a floppy
disk or copying entire sections of your hard disk to another media, such
as a CD-R or CD-RW discs.
Copying to a diskette
1. Insert a formatted floppy disk into the FDD drive (may not exist,
depending on the configuration of your computer).
®
2. Double-click the My Computer icon on the Windows desktop.
3. Double-click the drive that contains the file you want to copy.
4. Double-click the folder containing the file, then click the file you want
to copy.
Use the Ctrl or Shift keys to select more than one file.
5. Click File, then click Send To.
6. Click the icon for the diskette drive.
You can also back up a file to a diskette by clicking the file (or files) you
want to backup with the secondary button, then pointing to Send To and
clicking 3 ½ Floppy (A:).
User's Manual
3-7
1 Last Saved on 30/05/2003 13:57
Learning The Basics
Working with StickyKeys
StickyKeys are an accessibility option that lets you use the Windows®,
ALT, SHIFT, or CTRL buttons in conjunction with other keys but by
pressing them one at a time.
Activating StickyKeys
1. Press the Shift key five times in a row. The dialog box opens.
2. Click OK to activate them, or Settings to open the Settings dialog
box. You can also access the Settings dialog box by going to the
Control Panel and opening Accessibility Options.
User-Defined Buttons
The two User-Defined buttons on your computer let you assign specific,
custom functions to them, such as opening your email program, and
Internet browser, or whatever else you can think of doing with your
software collection.
The Internet Button and the TOSHIBA Console Button
By default, the User-Defined buttons are configured with Internet and
TOSHIBA Console functionality. The Internet button opens your default
Internet web browser, while the TOSHIBA Console button opens the
TOSHIBA Console.
Configuring the Buttons
1. Right-click the Easy Button software icon in your system tray
notification area.
2. From the pop-up menu, click the Configuration option.
3. Select the button you’d like to configure from the menu.
4. If you use a factory-set, pre-defined function, then select the function
you’d like to assign to that button from the list.
5. If you’d like to use a custom function, select the Application Launch
option, then Browse for the program to which you’d like to assign the
button.
6. In the Caption entry box, enter the name you’d like to assign to the
button. This appears on-screen when pressed.
User's Manual
3-8
1 Last Saved on 30/05/2003 13:57
Learning The Basics
Configuring the On Screen Display
1. Right-click the Easy Button software icon in your system tray
notification area.
2. From the pop-up menu, click the OnScreen Display option.
3. Click the Font button to open the Choose Font dialog box and select
the font you’d like to appear in the OSD.
4. Click the Colour button to open the Windows Colour Picker and se
the colour for the OSD text.
5. Use the Size menu to define the size of the on screen text, and the
Display box to set how long the text remains on the screen.
6. The Enable option lets you turn OSD text on and off.
Using Compact Discs And DVDs
The CD-ROM drive lets you read CD-ROM discs and play audio Compact
Discs. Your computer also includes a DVD-ROM drive, allowing you to
play DVDs as well as CDs. The procedures for using DVDs are the same
as those described for CDs below.
EJECT BUTTON
MANUAL EJECT
When inserting and removing CD-ROM and DVDROM discs, be careful
not to touch the lens on the disc tray or the area around it, as this may
cause the drive to malfunction or permanently damage its components.
User's Manual
3-9
1 Last Saved on 30/05/2003 13:57
Learning The Basics
The CD-ROM / DVD-ROM / CD-RW/DVD / DVD-R/-RW /
DVD Multi drive
Press the eject button to open the disc tray. The eject button will open
the disc tray even when the computer is off if the battery has power and
the computer is in CD mode.
If the computer is turned off and there is no power, use the manual eject
button.
Inserting discs into the drive
1. Press the eject button to open the disc tray.
2. Pull the disc tray until it is fully open.
3. Hold the disc by its edges, ensure it is dust-free, and place it carefully
in the disc tray, with the label side up.
4. Press down on the disc until it locks on the spindle.
5. Close the disc tray.
If the disc is not seated properly when you close the disc tray, the disc
might be damaged and the tray may not open fully when you press the
eject button.
Removing discs from the drive
1. Press the eject button.
Do not press the eject button while the computer is accessing the
CDROM/DVD-ROM drive (the Module Bay LED on the left side of the
keyboard flashes when the system is accessing the disc drive). If the disc
is still spinning when you open the disc tray, wait for it to stop before you
remove it.
2. Pull the disc tray until it is fully open, remove the disc, and place it in
its protective cover.
Playing compact discs
Turn to chapter 1 to learn about the CD control buttons which are located
on the front of your computer. For information on playing DVDs and
digital music files such like MP3s, and on playing CDs with your computer
turned off, see chapter 5.
User's Manual
3-10
1 Last Saved on 30/05/2003 13:57
Learning The Basics
Opening the disc tray with the computer off
When your computer is turned off, you can remove and insert CDs in two
ways. You can turn your computer to CD mode by pressing the
CD/Digital Mode button for more than 3 seconds and then use the eject
button as normal. Alternatively, use the manual eject button:
1. Insert a slender object, such as a straightened paper clip, into the
manual eject hole.
Never use a pencil to press the manual eject button. Pencil lead can break
off inside the computer end and damage the devices.
2. Pull the disc tray until it is fully open, insert a CD, or remove it and
place it in its protective cover.
Caring for compact discs and DVDs
■ Store your CDs and DVDs in their original containers to protect them
from scratches and keep them clean.
■ Don’t bend a disc or place heavy objects on top of it.
■ Don’t apply a label to, or otherwise mar, the surface of a CD or DVD.
■ Hold a disc by its outside edge. Fingerprints on the surface of a disc
can prevent the drive from reading the data properly.
■ Don’t expose CDs or DVDs to direct sunlight or extreme heat or cold.
■ To clean a disc, wipe it with a clean, dry cloth—starting from the
centre of the disc and wiping toward the outward edge. Do not wipe
using a circular motion. If necessary, moisten the cloth with water or a
neutral cleaner (not benzene or rubbing alcohol). Let the CD dry
completely before inserting it in the drive.
Using PC Cards
PC Cards expand your computer’s capabilities and usefulness. You can
purchase additional PC Cards from your dealer. Most PC Cards conform
to the PCMCIA (Personal Computer Memory Card International
Association) standard.
Your Satellite computer comes with two stacked PC Card slots and
supports two types of PC Card:
■ Type II cards are typically used for fax/modems, memory storage,
network cards, etc. You can install up to two of these cards, one in
each slot.
■ Type III cards are used for removable hard disks and other functions
that require a larger card. You can install just one of these cards No
Type II card can be installed when Type III card is installed.
Check the documentation that came with the PC Card to see if it conforms
to the PCMCIA 2.1 standard, or later. Other cards may work with your
computer, but are likely to be much more difficult to set up and use.
User's Manual
3-11
1 Last Saved on 30/05/2003 13:57
Learning The Basics
Inserting PC Cards
PC Cards require Card and Socket Services software, which is
preinstalled with Microsoft® Windows® XP. This is a set of programs that
acts as a translator between the PC Card and the computer that makes
hot swapping (switching cards while the computer is on) possible.
TYPE II/III PC CARD
SLOT
TYPE II PC CARD SLOT
Microsoft® Windows® XP operating system provides the Card and Socket
Services for your PC Card. Even if your PC Card comes with its own
version of Card and Socket Services, you should use the files included in
Microsoft® Windows® XP operating system. Some PC Cards do not
support hot swapping. Refer to your PC Card’s manual for information.
An HDD or CD-ROM connected to a 16-bit PC card, might affect the
performance of the computer’s sound system and data transmission,
including slower transmission speeds and dialling errors.
1. If your PC Card does not support hot swapping, save your data and
turn off the computer before inserting the PC Card. For more
information, see “Hot swapping” later in this chapter.
2. Hold the PC Card with the arrow side up and the connector side
toward the slot.
3. Align the card connectors with an available PC Card slot and carefully
slide the card into the slot until it locks into place.
There are two eject buttons, one per slot. When the PC card is seated,
the eject button for that slot pops out.
4. Press the eject button to put it in its retracted position.
If you have a Type III card, insert the connector into the lower slot. If you
have a Type II card, insert it into either the upper or the lower slot.
To avoid damaging the computer or the PC Card, don’t force the card into
the slot.
User's Manual
3-12
1 Last Saved on 30/05/2003 13:57
Learning The Basics
Removing PC Cards
1. Double-click the Safely Remove Hardware icon in the taskbar
notification area.
2. Select the PC Card that you want to remove from the list, then click
Stop.
3. A dialog box opens, from which you select the name of the PC Card
you wish to stop. Click OK.
4. A message will appear indicating that you can safely remove the card.
5. Gently press the eject button beside the slot it occupies.
If your PC Card supports hot swapping, you can remove it at any time.
However, to avoid date loss, never remove a card while it is in use. For
more information, see “Hot swapping”.
The upper eject button will pop out the Type II PC Card from the
upper slot. The lower button will pop out a Type II, or Type III card
from the lower slot.
6. Remove the PC Card and store it properly.
PC CARD EJECT
BUTTONS
Hot swapping
You can replace one PC Card with another while the computer is on. This
is called “hot swapping.”
Hot swapping precautions
Although you can insert a PC Card at any time, to avoid data loss do not
remove a card while it is in use. Before removing a PC Card, stop it by
clicking the PC Card (PCMCIA) icon on the taskbar. After the PC Card is
stopped, it is safe to remove it. It is recommended not to insert or remove
PC cards when system is in stand by or hibernation mode.
■ Don’t remove a hard disk card while the system is accessing it.
■ Don’t remove a network card while you are connected to a network.
■ Don’t remove a SCSI card while any of the SCSI devices connected to
it is operating.
SCSI is an acronym for Small Computer Systems Interface. A single SCSI
PC Card enables you to connect several SCSI devices, such as a scanner
or digital camera to your computer.
User's Manual
3-13
1 Last Saved on 30/05/2003 13:57
Learning The Basics
Using SD Cards
SD Cards are small media cards capable of dynamically storing data,
similar to a floppy disk. Your computer can read from and write upon SD
Cards, which are often used in devices such as digital cameras, digital
video recorders, MP3 players, and others. Your computer can support the
following size of SD Cards: 8/16/32/64/128/256/512MB.
Do not attach stickers or labels to the card or you may cause a
malfunction when it is being read or ejected.
Inserting SD Cards
Hold the SD Card with the gold contact area facing down and the
notched corner on the right side. Gently slide it into the SD Card slot until
it clicks into place.
If the system can not recognize SD cards correctly, please format SD
cards with TOSHIBA SD Memory Card Format utility.
If SD card is formatted, all of data will be erased.
User's Manual
3-14
1 Last Saved on 30/05/2003 13:57
Learning The Basics
Removing SD Cards
1. Double-click the Safely Remove Hardware icon in the taskbar
notification area.
2. Select the TOSHIBA SD Memory Card Drive from the list, then click
Stop.
3. A dialog box opens, select the TOSHIBA SD Memory Card Drive
again. Click OK.
4. A message "The 'TOSHIBA SD Memory Card Drive' device can now
be safely removed from the system." will appear.
5. Push in the card and release it to pop the card out slightly.
6. Grasp the card and remove it.
Make sure the SD Card indicator to the left of the keyboard is out before
you remove the card or turn off the computer’s power. If you remove the
card or turn off the power while the computer is accessing the card you
may lose data or damage the card.
Do not insert or remove SD Card when system is in stand by mode or
hibernation mode. System may fail to recognize the card.
User's Manual
3-15
1 Last Saved on 30/05/2003 13:57
Learning The Basics
Using Your Computer As A Desktop Computer
By connecting an external monitor, external full-size keyboard, and a
mouse, you can work with your notebook as if it were a standard desktop
computer.
An external monitor connects to the external monitor port.
Any USB devices including an external keyboard and pointing device
connect to any of the three USB ports.
See chapter six for more details.
Using a computer lock
You may want to secure your computer to a heavy object such as your
desk. The easiest way to do this is to purchase a computer cable lock
(pictured below).
1. Feed the cable through or around some part of a heavy object.
Make sure there is no way for a potential thief to slip the cable off the
object.
2. Pass the locking end through the loop.
3. Insert the cable’s locking end into the security lock slot, then rotate
the key a quarter turn and remove it; the computer is now securely
locked.
SECURITY LOCK SLOT
User's Manual
3-16
1 Last Saved on 30/05/2003 13:57
Learning The Basics
Setting Up Communications
To connect to the Internet, use an online service, or communicate across
the telephone lines with another computer, you need:
■ A modem (supplied with your Satellite notebook computer).
■ A telephone line.
■ A browser (supplied with your computer) or communications program.
■ An Internet Service Provider (ISP) or online service if you plan to use
the Internet.
Never connect the Modem jack to a digital line. The high current of digital
lines can damage the modem.
Connecting the modem to a telephone line
Before you can use the modem, you must connect it to a standard voicegrade telephone line.
Disable Call Waiting before you connect through the modem. Call Waiting
interrupts data transmission.
If you use a storage device such as a CD-ROM drive or HDD connected to
a 16-bit PC card, modem speed might be slow or communication might
be interrupted.
1. Plug one end of a standard RJ-11 telephone cable into the modem
jack.
MODEM JACK
2. Plug the other end of the RJ-11 telephone cable into the modular jack
of a standard voice-grade telephone line.
The telephone cable plug may be different in your country.
User's Manual
3-17
1 Last Saved on 30/05/2003 13:57
Learning The Basics
Connecting your computer to a network
To access a network:
■ You need to connect a network cable with an RJ-45 connector to the
LAN Jack. For specific information about connecting a LAN or WAN,
consult your network administrator.
LAN JACK
The computer must be configured properly before connecting to a LAN.
Logging onto a LAN using the computer’s default settings could cause a
malfunction in LAN operation. Check with your LAN administrator
regarding setup procedures.
When the system is in the power saving mode (Hibernate), network
devices such as the modem and LAN will not function and will not
maintain network connection.
■ You need a dial-up connection. Ask your network administrator for the
telephone number of the network.
To set up the connection, use the New Connection Wizard:
1. Click Start and point to All Programs.
2. Point to Accessories, then to Communications, and click New
Connection Wizard.
When you are connected to a network, disable your Microsoft® Windows®
operating system Standby command. The Standby command can disrupt
your network connection. You can disable the Standby command in
Power Options (in Control Panel) or the TOSHIBA Power Management
Utility (click the icon on the taskbar).
Connecting directly to a remote computer
If you are connecting directly to a remote computer or a bulletin board
service (BBS), you need a general-purpose communications program.
In addition, there are two things you need to know before you can
connect to another computer:
■ The communications parameters.
■ The file transfer protocol (only if you are downloading or uploading
files).
User's Manual
3-18
1 Last Saved on 30/05/2003 13:57
Learning The Basics
Communications parameters
There are four communications parameters:
■ Modem speed - The speed at which the modem transfers information.
Speeds are measured in bits per second.
■ Data bits - The number of bits in one character. This number is usually
seven or eight.
■ Stop bit - Indicates the end of a character. This number is usually one
or two.
■ Parity - An error-checking method, which will be set to even, odd, or
none.
Communications parameters, except for the modem speed, are usually
abbreviated and combined. Common examples are N81 (no parity, eight
data bits and one stop bit) and E72 (even parity, seven data bits and two
stop bits).
You set each of these parameters in your communications program. Each
parameter must be set the same on both computers or you will not be
able to connect.
To check your modem’s settings and communications parameters:
1. Click the My Computer icon with the secondary button, then click
Properties.
Windows® operating system displays the System Properties dialog
box.
2. Click the Hardware tab, then the Device Manager button.
3. Click on the modem name listed under Modems.
®
Windows operating system displays your modem’s Properties dialog
box. This dialog box contains information about your modem
configuration and status.
File transfer protocols
File transfer protocols are standards that govern how computers transfer
files between modems over a telephone line. You do not really need to
know anything about specific protocols-just make sure you are using the
same protocols as the computer with which you are communicating.
User's Manual
3-19
1 Last Saved on 30/05/2003 13:57
Learning The Basics
Turning Off The Computer
It is a good idea to turn off your computer when you are not using it for a
while. Click on Start, then click Turn Off Computer. You will be given the
options to Standby, Turn Off or Restart.
■ If you have work in progress and expect to resume shortly, use your
Microsoft® Windows® operating system Standby command to save
your system settings so that, when you turn on the computer again,
you automatically return to where you left off.
To leave the computer turned off for a longer period, use your
Microsoft® Windows® operating system Turn Off command instead.
■ Never turn off the power if the hard disk drive light is on. It may
damage your hard disk drive.
Closing the lid of your computer can be set to put your computer into
Standby. Click on Start, Control Panel, then Power Options and select
Advanced to choose your preferred setting.
Caring For Your Computer
This section gives tips on cleaning and moving your computer. For
information about taking care of your computer’s battery, see “Running
the computer on battery power” in chapter 4.
Cleaning the computer
To keep your computer clean, gently wipe the display panel and exterior
case with a lightly dampened cloth. Ask your TOSHIBA dealer for
suggestions for appropriate cleaning products.
Keep liquid, including cleaning fluid, out of the computer’s keyboard,
speaker grille, and other openings. Never spray cleaner directly onto the
computer. Never use harsh or caustic chemical products to clean the
computer.
Moving the computer
Before moving your computer, even across the room, make sure that all
disk activity has ended (check the system status indicator LEDs) and that
all external peripheral cables are disconnected.
Don’t pick up the computer by its display/panel or by the back (where the
ports are located).
User's Manual
3-20
1 Last Saved on 30/05/2003 13:57
Learning The Basics
Restoring the pre-installed software
If pre-installed files are damaged, use the Product Recovery CD-ROM.
Restoring the complete system
To restore the operating system and all pre-installed software, follow the
steps below.
When you reinstall the Windows® operating system, the hard disk will be
reformatted and all data will be lost. Make sure YOU have a backup copy
of your data, before you perform a complete system recovery.
1. Load the Product Recovery CD-ROM in the drive and turn on the
computer power.
2. When “In Touch with Tomorrow TOSHIBA” appears, press the F12
key. The Boot Menu appears.
3. Use your cursor keys to select the CD-ROM/DVD drive in the display
menu.
4. Follow the on-screen directions.
5. If your computer came with additional software installed, this software
can not be recovered from the Recovery CD. Re-install these
applications (e.g. Works Suite, DVD Player, Games, etc) separately
from other media.
TOSHIBA’s Online Resources
TOSHIBA maintains a number of online sites to which you can connect.
These sites can provide information about TOSHIBA products, give help
with technical questions, and keep you up to date with future upgrades.
For information on contacting TOSHIBA, see Appendix E.
User's Manual
3-21
1 Last Saved on 30/05/2003 13:57
Mobile Computing
Satellite P20
Chapter 4
Mobile Computing
This chapter covers all aspects of using your computer while travelling.
TOSHIBA’s Energy-Saving Design
TOSHIBA is a partner in the Energy Star Program and has designed this
product to meet the Energy Star guidelines for energy efficiency.
Your computer enters a low-power state when it is not being used,
thereby conserving energy and saving money in the process. It has a
number of other features that enhance its energy efficiency.
Many of these energy-saving features have been set by TOSHIBA. We
recommend you leave these features active, allowing your computer to
operate at its maximum energy efficiency, so that you can use it for
longer periods while travelling.
Managing Power Usage
Your computer’s power-saving options increase the length of time you
can use the computer before you need to recharge the battery.
To change the power usage mode, click Start, then click Control Panel.
In Control Panel, double-click the Power Option icon (if in Category View,
then first click Performance and Maintenance to make the Power
Option icon appear) to display the Power Option Properties window.
Select the power scheme with the most appropriate settings for your
computer. Keep in mind that changing any settings on the Power Option
Properties window will modify the currently selected scheme.
Consult your Microsoft® Windows® operating system documentation for
more information on the Power Option utility.
If the TOSHIBA Power Management Utility is installed in your computer,
please run it by double-clicking its icon on the taskbar instead of the
Power Option icon. You can see more information in chapter 5.
User's
Manual
User's Manual
4-1
4-1
1 Last Saved on 30/05/2003 13:57
Mobile Computing
Running the computer on battery power
The computer uses a removable Lithium Ion (Li-ION) battery pack that
provides power when you are away from an AC power source. You can
recharge it many times.
In addition to the removable battery, the computer has an internal realtime clock (RTC) Lithium rechargeable battery. The RTC battery powers
the RTC memory, which stores your system configuration settings and
the current time and date for up to a month while the computer is turned
off.
Using additional battery packs
If you spend a lot of time travelling and need to work for many hours
without an AC power source, you may want to carry additional charged
battery packs with you. You can then replace a discharged battery and
continue working.
A new battery pack should be fully discharged, by running the computer
solely on battery power, and recharged three times when first used.
Maximizing battery life
A battery can be recharged many times. Gradually over time it will lose its
ability to hold a charge. To maximize the life of your battery:
■ If you are not going to use the computer for a long period of time,
remove the battery.
■ Alternate between battery packs if you have a spare.
■ Make sure the computer is off when you are replacing the battery.
■ Store spare battery packs in a cool dry place out of direct sunlight.
User's Manual
4-2
1 Last Saved on 30/05/2003 13:57
Mobile Computing
Charging Batteries
The battery needs to be charged before you can use it to power the
computer. You can charge the battery using your computer.
Charging the battery
To charge the battery while it is in your computer, plug the computer into
a live AC outlet. It takes approximately 4 hours to charge the battery to
full while the computer is off. It takes up to 12 hours or longer to charge
the battery to full while the computer is on -how long depends on what
other operations the computer is performing.
The battery only can charge a small current while the computer is
consuming full power.
The battery may not start charging immediately if:
■ The battery is extremely hot or cold.
To ensure that the battery charges to its full capacity, wait until it
reaches room temperature: 5°C to 35°C. (41°F to 95°F).
■ The battery is almost completely discharged.
Leave the power connected, and the battery should begin charging
after a few minutes.
Once a battery pack is fully charged, we recommend that you operate
your computer on battery power until the battery pack discharges
completely. Doing this extends battery life and helps ensure accurate
monitoring of battery capacity.
User's Manual
4-3
1 Last Saved on 30/05/2003 13:57
Mobile Computing
Charging the RTC battery
In addition to the main battery, the computer contains an internal battery
for the real-time clock (RTC). The RTC battery provides power for the
internal real-time clock and calendar.
During normal use, the main battery keeps the RTC battery adequately
charged. Occasionally, the RTC battery may lose its charge completely,
especially if you have had the computer turned off and without the main
battery pack inserted for a long time. In this event, your computer
displays the following error message:
ERROR 0271: Check data and time settings WARNING 0251: System
CMOS checksum bad - Default configuration used Press <F1> to
resume, <F2> to Setup.
It is seldom necessary to charge the RTC battery because it charges
while the computer is on. However, if the RTC battery is low, the real-time
clock and calendar may display the incorrect time and date or stop
working.
To recharge the RTC battery, plug the AC adapter into the computer for
at least 24 hours.
The computer can be used while the RTC battery is being charged.
Although the charging status of the RTC battery cannot be monitored, if
the power is on, it takes approximately 24 hours to fully charge the RTC
battery.
User's Manual
4-4
1 Last Saved on 30/05/2003 13:57
Mobile Computing
Monitoring Battery Power
The Battery LED indicates the battery’s current charge status. It lights
green when the battery is fully charged. It lights amber while the battery is
being charged from the AC adapter. It flashes amber when the battery
capacity is low. When the light is off, the battery is discharging.
BATTERY LED
Determining remaining battery power
Wait at least 20 seconds after turning on the computer before checking
the remaining battery power. The computer needs this time to check the
battery’s remaining capacity and perform calculations.
To check the battery level, you can look at the TOSHIBA Power
Management Utility, which can be found in the Windows® Control Panel.
To access the panel:
1. Click on the Start button, then click the Control Panel.
2. Double-click the TOSHIBA Power Management Utility icon (if in
Windows® XP Category View, first click Performance and
Maintenance to make the TOSHIBA Power Management Utility
icon appear.)
3. Choose the Battery Power Meter tab to show the current battery
status.
The computer drains the battery faster at low temperatures. Check your
remaining charge frequently if you are working in temperatures below
10 degrees Celsius (50 degrees Fahrenheit). The computer calculates the
remaining battery charge based on your current rate of power use and
other factors such as the age of the battery.
Before removing or after inserting the battery pack, click the TOSHIBA
Power Management Utility to show the latest battery status. Always
ensure the computer is turned off before removing the battery pack.
User's Manual
4-5
1 Last Saved on 30/05/2003 13:57
Mobile Computing
Conserving Battery Power
How long a fully charged battery pack lasts when you are using the
computer depends on a number of factors, such as:
■ How is the computer configured?
■ How much do you use the display panel instead of an external
monitor?
■ How much do you use the hard disk and other drives?
■ Do you use any optional devices that the battery supplies power to,
such as a PC Card?
■ What are your working conditions (operating time decreases at low
temperatures)?
See earlier in this chapter for information on maximizing battery life.
What to do when the battery runs low
When the battery runs low you have these options:
■ Plug the computer into a live AC outlet and recharge the battery.
■ Save your work and turn off the computer.
If you don’t manage to do any of these things before the battery
completely runs out of power, the computer automatically enters
Hibernate mode and keeps track of where you were so that when you
turn on the power by using AC adapter again, you can continue where
you left off. (You can configure the computer to enter Standby mode
instead. The default setting is Hibernate.)
When the battery capacity is below 5%, the system is protected and can’t
be re-powered on without the AC power being connected. In this
situation, the Battery LED will light amber for a short time to indicate this
condition. Keep depressing the power button, and the LED will blink
amber .
User's Manual
4-6
1 Last Saved on 30/05/2003 13:57
Mobile Computing
Battery Alarms
The computer can be configured to warn you when the battery is running
low. You can set each of the following alarms:
■ Low Battery
■ Critical Battery
Each alarm can be set to alert you when a specified percentage of
remaining battery power has been reached. You can also set how the
alarm action occurs – sound an alarm, display a message, both, or none.
You can also set the computer to enter Standby when the alarm goes off.
To set the alarm levels:
1. Click the Start button, then click Control Panel.
2. Double-click the TOSHIBA Power Mangement icon (if in Category
View, then first click Performance and Maintenance to make the
TOSHIBA Power Mangement icon appear).
3. Click the Alarms tab.
4. Set the alarm levels as desired.
®
®
For more information on battery alarms, refer to the Microsoft Windows
operating system documentation or Help.
For more about TOSHIBA Power Mangement Utility, see Chapter 5
User's Manual
4-7
1 Last Saved on 30/05/2003 13:57
Mobile Computing
Changing The Battery
When your battery runs out of power, you have two options- connect the
AC adapter or install a fresh battery. For instructions on using the AC
adapter, see “Connecting the AC adapter” in chapter 2.
Removing the battery
1. Save your work.
2. Turn off the computer. Never remove the battery while the computer is
on.
3. Close the display panel, ensuring that it snaps in to place.
4. Turn the computer upside down with the front of the computer facing
towards you.
5. Unlock the 2nd Module Bay Lock.
6. Slide the 2nd Module Release Latch toward the right.
7. Pull the battery carefully out of the 2nd Module Bay.
The2nd Module Bay Latch is spring-loaded and will snap back into place
when you release it.
User's Manual
4-8
1 Last Saved on 30/05/2003 13:57
Mobile Computing
Inserting a battery
1. Slide the battery into the 2nd Module Bay. When it is fully inserted,
you should hear it click into place (1).
The2nd ModuleBay Latch is spring-loaded and clicks as it latches the
battery in place when you insert it.
2. Turn the computer bottom side up and ensure the battery is fully
inserted in the bay. Also make sure that the 2nd Module Bay Latch is
secured to the left (2).
3. Secure the 2nd Module Bay Lock (3).
If the battery housing is leaking or cracked, put on protective gloves to
handle it and discard it immediately following the advice in the following
section on “Disposing of Used Batteries Safely”.
The battery can only be inserted into the 2nd Module Bay.
Disposing Of Used Batteries Safely
You can recharge a battery many times. When the useful life of the
battery expires or if the battery becomes damaged, you must discard it
responsibly.
Batteries should not be disposed of together with household waste. To
make sure that they are forwarded to recycling or proper disposal they
may be returned free of charge to an authorized TOSHIBA
dealer/distributor.
Use only batteries recommended by TOSHIBA as replacements.
The computer uses a Li-Ion battery which can explode if not handled or
disposed of properly. Putting spent batteries in the trash is not only
irresponsible, it may also be illegal. Dispose of the battery as required by
local ordinances or regulations.
User's Manual
4-9
1 Last Saved on 30/05/2003 13:57
Mobile Computing
Travelling Tips
Environmental precautions also apply on journeys.
■ Do not leave your computer exposed to direct sunlight for long
periods of time – for instance, on the dashboard of a car – or place it
where it could get wet or covered in dust.
■ Always travel with the computer in a carrying case. TOSHIBA offers a
choice of carrying cases for the computer. They all provide plenty of
extra space for manuals, power cables, CDROM discs, and floppy
disks, etc. See your dealer for more information.
When travelling by air, you maybe required to put your notebook through
airport security The X-ray equipment used may or may not harm your
computer.
Ensure your personal computer is turned off before you put it in your bag.
User's Manual
4-10
1 Last Saved on 30/05/2003 13:57
Using Advanced Features
Satellite P20
Chapter 5
This chapter explains many advanced features of your notebook
computer.
Multiple Displays
Adjusting display settings
You can adjust your display settings in Display Properties. Enter through
Start, Control Panel, Appearance and Themes, Display or, right-click
on the Windows® desktop then check Properties. Alternatively, right-click
on the display icon on the taskbar (if visible), choose Settings then
Display Settings. Following the on screen display step by step panels,
you will be able to adjust the appearance of your desktop. You will also
be able to configure your computer to use more than one display. Follow
the instructions on the next two pages.
Using multiple displays
Your computer can be simultaneously connected to a computer monitor
and television display while also using the built-in panel display. These
displays can be configured to mirror each other, or they can be arranged
as separate portions of a single desktop.
For information on how to attach a television and computer monitor to
your computer, please see chapter 6.
Make sure the computer is turned off before connecting an external
monitor or television.
User's
Manual
User's Manual
5-1
5-1
1 Last Saved on 30/05/2003 13:57
Setting up more than one display
Make sure that the display device is connected and select the Settings
tab in Display Properties. Click on Advanced and select GeForce FX
Go5200. Click nView Display Mode in the menu on the left side by
clicking the tab. The display devices attached to your computer will be
shown. If not, click Detect Displays. If the nView tab is not visible when
you click Advanced, turn first to the instruction on the next page.
1. If you have more than one external display attached to your computer,
select the displays you want to use by right-clicking on either of the
pictures in the above window and selecting Select Output Device.
2. Select the display mode you want to use. You have the option of
configuring both displays as clones (so that the image on one is
exactly mirrored on the other) or configuring the two displays as a
single desktop. This has the advantage of greatly expanding the
desktop area, allowing you to, for instance, play a DVD on the
television screen while running a word processor on the computer’s
built-in display
After selecting your preferred display mode, Click Apply.
User's Manual
5-2
1 Last Saved on 30/05/2003 13:57
Multiple display properties
If the nView tab is not visible when you click the Advanced button on the
Settings tab of the Display Properties window, you must adjust your
settings before using nView. Disable your existing dual monitor settings
under the Settings tab by doing the following.
1. Click on the monitor icon marked 2. Make sure that the Extend my
Windows desktop onto this monitor box is not checked.
2. Click on the monitor icon marked 1 and then click Apply.
When the new settings have taken effect, make sure that monitor icon 1 is
highlighted and click Advanced. The nView tab should now be
accessible.
User's Manual
5-3
1 Last Saved on 30/05/2003 13:57
The Display Properties window allows you to adjust more precisely the
relative positioning of the two displays when they are configured as an
extended desktop. On the Display Properties window, the two displays
can be positioned horizontally, vertically or in any diagonal configuration
you wish, as shown below.
If an external display will not be connected next time you use your
computer, you should cancel any extended desktop or clone display
settings before shutting down your computer.
User's Manual
5-4
1 Last Saved on 30/05/2003 13:57
Playing DVDs
The WinDVD software for playing DVD movie titles is already installed. To
use it, simply insert the DVD disc into the disc tray. Your computer will
launch the WinDVD software automatically.
Using a CD-RW, DVD-R/-RW or DVD Multi Drive
If your computer comes with either the CD-RW, DVD-R/-RW or DVD Multi
Drive, you can write to either CD-R, CD-RW, or DVD-R media.
For CD authoring, Drag ‘n Drop CD+DVD software comes preinstalled
with the computer. For more on how to use it, please refer to the
program’s online help file. For DVD authoring, there is a disc called
Motion DV Studio. You have to install the software by yourself. First,
insert the disc into the drive, then the setup dialog box shows up
automatically. You can then follow the onscreen display step by step
method to install it.
For more Information on using Drag’n Drop CD+DVD software, please
consult the documentation that came with it.
When using the CD-RW, DVD-RW or DVD Multi drive device, do not copy
data directly from an external device. (e.g. USB, i.LINK device). Please
copy the data into the Hard Disk Drive, then copy to the disc.
About DVD-RAM
The Multi-drive device supports the DVD-RAM (DVD Random Access
Memory) media. This allows data to be written and rewritten on a disc up
to 100,000 times. Data, including video and audio files, can be stored on
a DVD-RAM disc and accessed just as with a hard drive using standard
drag-and-drop techniques. Single-sided (4.7GB) and double-sided
(9.4GB) media are available as bare discs or enclosed in cartridges.
User's Manual
5-5
1 Last Saved on 30/05/2003 13:57
Playing CDs, DVDs And Digital Music Files With The
Computer On Or Off
You can listen to CDs with the computer turned off and also start playing
digital music files and DVDs, in which case the computer will turn on
automatically.
Use the CD/Digital Mode button on the front of the computer to switch
between CD mode and Digital mode.
Whether your computer is turned on or off, the CD/Digital control buttons
are locked by default. To unlock them, press the CD/Digital mode button
for more than 3 seconds. Press the mode button again for over 3 seconds
to lock them again. When the computer is off and in CD or Digital mode,
the buttons will lock automatically after 2 minutes if Play is not pressed
and no CD is playing.
CD/DIGITAL MODE
BUTTON
PREVIOUS
NEXT
CD MODE INDICATOR
LED
DIGITAL MODE
INDICATOR LED
STOP/EJECT
PLAY/PAUSE
You can refer to chapter 1 for instruction on using the CD control buttons.
CD Mode
Computer Power Off state: You can use the CD controls to play an
audio CD without turning on the computer. Press the CD/Digital Mode
button for more than 3 seconds until the Direct CD LED lights, then press
play. If there is no response, press Stop/Eject and check to make sure a
CD is correctly placed in the CD tray.
If a DVD is in the drive, pressing play will turn the computer on in order to
start playing the DVD title (as long as your computer is equipped with a
DVD drive).
Computer Power On state: Press the CD/Digital Mode button for more
than 3 seconds until the Direct CD LED lights. Pressing play will launch
the media application appropriate for either a CD or DVD. If the CD tray is
empty, an alert window will inform you.
User's Manual
5-6
1 Last Saved on 30/05/2003 13:57
Digital Mode
In Digital mode, your computer can play DVD video, MP3s, Wav files, Midi
files, and other forms of digital music file.
When the CD control buttons are unlocked (by pressing the CD/Digital
Mode button for over three seconds) the computer initially enters the CD
mode. Switch to Digital Mode by pressing the Mode button again briefly.
Computer Power Off state: If you push the play button while the
computer is off and in Digital Mode, the computer will power on, launch
Microsoft Windows Media Player and play by default from the digital
playlist.
Computer Power On state: If you push the play button while the
computer is on and in Digital Mode, Microsoft Windows Media Player will
launch and start playing by default from the digital playlist.
Using The FIR Port
You can transfer files to another computer using your Satellite notebook
computer’s FIR (Fast Infrared port). Both computers involved in the data
transfer must have compatible infrared ports and synchronization
software. Your computer may not have this function, depending on the
model bought.
FIR PORT
User's Manual
5-7
1 Last Saved on 30/05/2003 13:57
Using The TOSHIBA Remote Control
You can control your Windows® software, digital media files and files on
CDs or DVDs with the remote control device that ships with your
computer. Not all models will come with a TOSHIBA Remote Control. The
receiver port on the front of your computer should not be blocked or
covered for it to work. To use, simply point the controller towards the
computer’s front panel and press the appropriate button.
Not all models ship with the TOSHIBA Remote Control
The remote control’s features are:
Power On/Off
Turns the computer on and off.
TV Out
Changes display to an external TV.
Maximize/Restore
Maximize the active window, or restores it to its
original size
Switch Window
Cycles through any open windows.
Volume Up/Down
Turns the volume up or down.
Volume Off
Turns the volume all the way down.
Pressing the button a second time restores the
volume to its last level.
Pointer Controls
These five buttons control the pointer’s position
on screen. The button in the centre is the ‘Enter’
button.
User's Manual
5-8
1 Last Saved on 30/05/2003 13:57
Tab Key
Identical to the keyboard’s tab key.
Menu
Calls up the DVD menu during DVD playback.
Mode
Switches modes.
Play/Pause
Plays and/or pauses the current track, whether it
is a DVD or CD.
Stop
Stops playing.
Previous
Skips to the previous chapter/track.
Fast Backward
Shuttles backwards through the track.
Fast Forward
Shuttles forwards through the track.
Next
Skips to the next chapter/track.
Using Wireless LAN
Your computer may integrate 802.11b or 802.11a/b Wireless Networking,
depending on the model purchased. It is a high- speed wireless network
connection that uses two-way radio transmission to communicate with an
“Access Point” transceiver that is physically connected to the network by
cable.
The Atheros Client Utility, which is the Wireless Networking driver utility,
has been pre-installed and setup on the computer. You may get detailed
operating and setup information from its online Help.
This utility should be used only if you have an 802.11a/b setup, but not for
802.11b. If you are using 802.11.b, use the manager built into
Windows® XP. Adhoc mode is only supported on 802.11b.
1. Slide the Wireless Communication switch to turn on the Wireless
Networking. The LED will light amber to show the on status.
2. Run the TOSHIBA Client Manager from the system task bar to
connect the nearest Access Point if you are using 802.11a/b.
With the Wireless Communication switch in the ‘on’ position, Wireless
LAN activity can be turned on and off at any time by pressing the hot key
Fn + F8.
Please turn off wireless networking feature before boarding a plane or
entering a hospital.
User's Manual
5-9
1 Last Saved on 30/05/2003 13:57
Using The TOSHIBA Power Management Utility
The TOSHIBA Power Management Utility is pre-installed in your
computer. This software allows you to select the power scheme with the
most appropriate settings for this computer.
You can double click the TOSHIBA Power Management Utility icon on the
system taskbar to execute the program. Following the on-screen display
step by step panels, you will find following settings.
1. Battery Mode: Lets you select either Long Life, Normal, High Power or
DVD Playback power schemes. For each individual setting, you can
adjust Monitor Brightness, Turn Off Monitor, Turn Off Hard Disks,
System Stand By, and System Hibernate at different battery power
capacity.
2. AC Mode: There is one Power Scheme, which is Full Power. As with
the various battery modes, you can adjust the specifics for Full Power
management.
3. Alarm: You can adjust the Low Battery Alarm and Critical Battery
Alarm when the Battery Power reaches a certain level. The Alarm
Action be either sound Alarm or Display message or both.
4. Advanced: Lets you can select the power saving settings you want to
use. You can select the power button and lid switch function here.
You can also select the cooling method you want to use.
5. Battery Power Meter: Displays the current the power source and
Battery Power capacity. You can see the current battery capacity on
the edge of right side of the on-screen display. After finishing your
settings, you should click OK to confirm or cancel to ignore the new
settings.
User's Manual
5-10
1 Last Saved on 30/05/2003 13:57
Expanding & Upgrading
Satellite P20
Chapter 6
This chapter covers things you can do to expand and upgrade your
computer including connecting external peripherals, buying additional
disk drives to attach externally and installing more system memory.
Using External Peripherals
Your computer is ideally suited for use as a desktop computer in the
office or at home. If you frequently use your computer at one location,
you might want to connect a number of peripheral devices, such as a fullsize keyboard, speakers, a larger display device or speakers, to boost
your computer’s capabilities and make it more comfortable to use. In this
section we’ll look at how to attach the most common devices.
User's
Manual
User's Manual
6-1
6-1
1 Last Saved on 30/05/2003 13:57
Connecting A USB Keyboard
You can install a full-size USB keyboard. This may be more convenient for
some tasks and saves wear and tear on the computer’s built-in keyboard.
RIGHT USB PORTS
REAR USB PORTS
To install an external USB keyboard do as follows:
1. Plug the keyboard into one of the USB ports on the computer. We
recommend that right-handed users connect the keyboard to one of
the rear ports, keeping the port on the right side of the computer free
for an external pointing device. Left-handed users may find it more
convenient to reverse that arrangement.
2. If the keyboard has advanced features that require a driver or other
software, install it according to the instructions that come with it.
3. Position the keyboard where you want to use it.
devices.
User's Manual
6-2
1 Last Saved on 30/05/2003 13:57
Connecting An External USB Pointing Device
You can install an external USB pointing device, such as a mouse, to use
instead of, or in addition to, the built-in Touch pad device. You can use
any type of pointing device as long as it has a USB interface.
RIGHT USB PORTS
REAR USB PORTS
To install an external USB pointing device do as follows:
1. Plug the device into one of the USB ports on the computer. We
recommend right-handed users attach the device to the USB port on
the right-hand side of the computer; left-handed users may find it
more convenient to use one of the USB ports on the rear.
2. The device may require a driver and possibly other software. Install it
according to the instructions that come with it.
3. Position the device where you want to use it.
devices.
User's Manual
6-3
1 Last Saved on 30/05/2003 13:57
Connecting An External Monitor
You might want to connect an external monitor to your computer to have
a larger screen and to reduce wear on the built-in LCD screen. You can
connect a CRT desktop monitor to the standard 15-pin external monitor
port on the rear of the computer, or, if the monitor has a USB interface, to
one of the USB ports.
EXTERNAL MONITOR
PORT
To connect a monitor to the external monitor port do as follows:
monitor.
2. Check the instructions that come with the monitor.
3. Plug the 15-pin VGA connector from the monitor onto the external
monitor port of the computer.
4. Tighten the screws on the connector to secure the connector to the
monitor.
If the monitor supports “Plug and Play” as most newer monitors do,
®
®
Microsoft Windows operating system will automatically recognize and
configure the system for it. You can then use the Display Properties
control panel to configure display settings for the monitor. See chapter 5
for details.
User's Manual
6-4
1 Last Saved on 30/05/2003 13:57
Connecting A Television
You might want to connect a television to your computer to have a larger
screen to watch DVDs. You can connect a television by using an S-video
cable in the TV Out port on the right side of the computer.
TV OUT PORT
To connect a television to the TV Out port do as follows:
television.
2. Check the instructions that come with the television.
3. Plug the connector from the television onto the TV Out port of the
computer.
You can use the Display Properties control panel to configure display
settings for the television. See chapter 5 for details.
User's Manual
6-5
1 Last Saved on 30/05/2003 13:57
Connecting Audio Devices
The audio jacks on the left side of the computer allow you to connect
several devices including speakers and a microphone.
Connecting external speakers
You can connect self-powered stereo speakers to the computer to
provide better sound reproduction than that from the built-in speakers
and save wear on them.
HEADPHONE JACK
To connect self-powered external speakers do as follows:
1. Position the speakers where you want them.
2. Plug the mini-plug connector from the speakers into the Headphone
Jack on the left side of the computer.
3. Plug the speakers into a power source.
4. Turn on the computer and adjust the volume from the volume control
in the taskbar system tray. You may want to play something to check
the volume level.
The internal speakers are disabled when you connect external speakers
to the Headphone Jack.
User's Manual
6-6
1 Last Saved on 30/05/2003 13:57
Connecting A Microphone
If you want to use a microphone for recording, voice commands or
computer telephony, you can connect one to the microphone jack.
LINE-IN JACK
MICROPHONE JACK
To connect a microphone, do as follows:
1. Make sure the microphone you get is a standard computer
microphone with a 3.5mm mini-plug connector.
2. Plug the microphone into the microphone jack on the computer.
3. Adjust the microphone volume in the Windows Sounds and Audio
Devices control panel's Audio panel section by clicking on the Volume
button of Sound playback and Sound Recording.
Connecting A Line-In
The line-in jack lets you connect a digital audio line to your computer,
such as from a midi player.
1. Make sure the line-in cable you get is a standard Audio cable with a
mini-plug connector.
2. Plug the line-in cable into the line-in jack on the computer.
User's Manual
6-7
1 Last Saved on 30/05/2003 13:57
Additional Options
You can add new modules either externally, via the USB ports, or, by
means of the Main or 2nd Module Bay.
External floppy disk drive
You can purchase a TOSHIBA external USB floppy disk drive. The drive is
powered from the computer. You simply plug it in and it works.
RIGHT USB PORTS
REAR USB PORTS
Alternatively, you can purchase a TOSHIBA FDD module, which can be
inserted in the Main or 2nd Module Bay.
Module Bay Options
A FDD Module (floppy disk drive) or a second hard disc drive (HDD) can
be used in place of an Optical Media Drive (such as DVD-R/-RW). The
FDD goes into the Main Module Bay. The Windows® Operating System
automatically detects it, listing it in Explorer.
Alternatively, you can install a second Optical Media Drive in the 2nd
Module Bay, replacing the battery that normally goes there. The
Windows® Operating System automatically detects it, listing it in Explorer
below the one you already have.
User's Manual
6-8
1 Last Saved on 30/05/2003 13:57
Upgrading System Memory
You can upgrade the system memory in your computer. The computer
has two sockets for DDR SODIMM memory modules. They are located in
the memory compartment on the underside of the computer. Generally, at
least one socket has a module installed when you get the computer and
the other socket is empty to allow for upgrades, but depending on your
configuration you may actually have both sockets occupied with memory
modules.
The computer can have a maximum of 2 GB installed. This means it can
take two 1 GB memory modules.
If you want to upgrade the system memory, you should use only certified
modules. Ask your vendor or check the TOSHIBA web site for a list of
approved memory products. The basic specifications of the memory used
are:
■ DDR 266/333 specification compliant
■ 128MB, 256MB, 512MB or 1GB capacity
Installing additional memory
Unless you are familiar with computer upgrades and comfortable doing
so, we suggest that you have any memory upgrades installed at the
nearest TOSHIBA Service Centre.
If you want to install a memory upgrade yourself, do as follows:
1. Make sure the computer is turned off, with AC adapter disconnected
and battery removed.
Never add or remove memory modules with the computer on or in
Standby or Hibernation. Ensure the system is turned off, the AC adapter is
not connected and the battery has been removed.
User's Manual
6-9
1 Last Saved on 30/05/2003 13:57
2. Place the computer on a static-free surface and turn it over.
3. Remove the memory module cover by removing the two retaining
screws and lifting the cover panel out.
MEMORY MODULE
COVER
4. Insert the SO-DIMM module in the socket at about a 45º angle and
then press it down into the socket until it snaps in place.
User's Manual
6-10
1 Last Saved on 30/05/2003 13:57
5. Restore the memory module cover back to its place and secure it with
the two retaining screws.
The memory upgrade is now installed. Turn the computer right side up,
open it and turn it on. The system should automatically recognize the new
total memory capacity. You can check this by clicking on My Computer
with the right Mouse button, clicking on the Properties item in the menu
that appears and display the memory size in the General panel of the
System Properties control panel.
If you install a memory module that is not compatible with the computer, a
beep will sound and the LCD screen will be blank when you turn on the
power. In this case shut down the power and remove the incompatible
memory module.
User's Manual
6-11
1 Last Saved on 30/05/2003 13:57
If Something Goes Wrong
Satellite P20
Chapter 7
Some problems you may encounter when using the Satellite P20
computer are relatively easy to identify and solve. Others may require
help from your dealer or the manufacturer of a software program.
This chapter aims to help you solve many problems by yourself without
additional help. It covers the problems you are most likely to encounter.
If all else fails, contact nearest TOSHIBA dealer or service support. You
will find information on TOSHIBA’s support services in Appendix E.
Problems That Are Easy To Fix
Your program stops responding
If you are working with a program that suddenly freezes all operations, or
the execution program has stopped responding, you can exit the failed
program without shutting down the Microsoft® Windows® operating
system or closing other programs.
To close a program that has stopped responding:
1. Press Ctrl, Alt, and Del simultaneously (once).
The operating system displays the Windows Task Manager box. This
lists all the programs and processes currently in operation. Select the
Applications tab. If a program has stopped responding, the words
“not responding” appear beside its name in the list.
2. Select the program you want to close then click End Task.
Closing the failed program should allow you to continue working. If it
does not, continue with step 3.
3. Close the remaining programs one by one by selecting the program
name and clicking End Task.
4. Click on the Shut Down drop-down menu of the Windows Task
Manager box and select Restart.
Your computer shuts down and restarts, thus restoring operations.
Pressing Ctrl, Alt, and Del simultaneously twice to restart your computer is
not recommended. By closing all open programs prior to shutting down
Microsoft® Windows® operating system you ensure that all data is saved.
User's
Manual
User's Manual
7-1
7-1
1 Last Saved on 30/05/2003 13:57
Your program performs an illegal operation
If you receive the message, “Your program has performed an illegal
operation,” you should record the details of the message and consult the
software manufacturer.
To record the details:
1. Click the Details button and select the text, Microsoft® Windows®
operating system displays.
The Details button displays information that the software manufacturer
needs to help you solve your problem.
2. Press Ctrl and c simultaneously to copy the text to the clipboard.
3. Open Notepad (click Start, point to All Programs, then point to
Accessories and click Notepad).
4. Press Ctrl and v simultaneously to paste the details into Notepad.
5. Add a paragraph break and type some notes describing what you
were doing when you received the message.
6. Save the file and refer to it when you contact the software
manufacturer.
Hyper Threading Technology Incompatibility
Some applications may not be compatible with Hyper Threading
Technology (HTT). If an application does not work with HTT, try disabling
it as described below.
1. Turn the computer on.
2. Press F2 key to enter BIOS setup menu when TOSHIBA logo appears
on the screen.
3. Set [Disable] in [Advanced]->[Hyper Threading Technology]
4. Reboot the computer.
Windows2000 does not support HTT. HTT should be disabled if
Windows2000 is installed before Windows2000 setup.
Not all of models come with HTT.
Problems When You Turn On The Computer
These problems may occur when you turn on the power.
The computer will not start
Make sure you attached the AC adapter and power cable properly or
installed a charged battery.
Press and hold down the power button for a few seconds.
User's Manual
7-2
1 Last Saved on 30/05/2003 13:57
The computer is not accessing the hard disk or the
diskette drive
Your computer normally loads Windows from the hard disk. If you have a
hard disk problem, you will not be able to start the computer. Insert a
system diskette into the diskette drive, then press the power button.
Power problems
The computer displays the Non-system disk or disk error message.
Make sure there is no diskette in the diskette drive. If there is one, remove
it and press any key to continue. If pressing any key does not work press
Ctrl, Alt, and Del and select Shut Down and then Restart or turn off the
computer by holding down the power button for several seconds.
Fixing Device-Related Problems
If you do not have a hardware conflict, but you think your problem could
be related to one of your computer’s devices, you can use:
■ Dr. Watson - A diagnostic tool that takes a snapshot of your system
whenever a system fault occurs. To open Dr. Watson click Start, and
then click Run. In the Open box, type drwtsn32.
■ System Information - Collects your system configuration information
and provides a menu for displaying the associated system topics. To
open System Information click Start, and then click Run. In the Open
box, type msinfo32.
Refer to your operating system documentation for more information on
using these tools. After diagnosing the problem, read the part of this
section that describes problems and solutions related to specific devices.
Memory module problems
Incorrectly connected or faulty memory modules may cause errors that
seem to be device-related. So it is worthwhile checking for these first:
1. Click Start, then click Turn Off Computer.
2. Select Turn Off.
®
®
Microsoft Windows operating system shuts down and turns off the
computer automatically.
3. Remove the memory module(s).
4. Reinstall the memory module(s), following the instructions in Chapter 6
and making sure they are seated properly in the module sockets.
5. Check for the error again.
6. If the error recurs, remove the memory module entirely and check for
the error again using the second or another module.
If removing the memory module eliminates the error, the module may be
faulty. If the error occurs without the module installed, the module is not
causing the error.
User's Manual
7-3
1 Last Saved on 30/05/2003 13:57
Power Problems
Your computer receives power from the battery which is charged through
the AC adapter. Power problems are interrelated. For example, a faulty
AC adapter or power cable will neither power the computer nor recharge
the battery.
Here are some typical problems and how to solve them:
The DC-IN LED does not come on when you plug in the
AC adapter and power cable
Make sure the AC adapter and attached power cable are plugged into
both a working wall outlet and the computer.
If the DC-IN LED still does not come on, check that the wall outlet is
working properly by plugging in a lamp or other appliance.
The AC adapter and power cable work correctly, but the
battery will not charge
The battery doesn’t charge while the computer is consuming full power.
Try turning off the computer or shutting down applications such as the
DVD player that use a lot of power.
The battery may not be inserted correctly in the computer. Turn off the
computer, remove the battery, clean the contacts with a soft dry cloth (if
necessary) and replace the battery.
The battery may be too hot or too cold to charge properly. If you think
this is the probable cause, let the battery reach room temperature and try
again.
If the battery has completely discharged, it will not begin charging
immediately. Leave the AC adapter and power cable connected, wait 20
minutes and see whether the battery is charging.
If the battery light is glowing after 20 minutes, let the computer continue
charging the battery for at least another 20 minutes before you turn on the
computer.
If the battery light does not glow after 20 minutes, the battery may have
reached the end of its useful life. Try replacing it.
The battery appears not to power the computer for as
long as it usually does
Check the power options using the TOSHIBA Power Management utility.
Have you added a device, such as a PC Card or memory module, that
takes its power from the battery? Is your software using the hard disk
more? Is the display power set to turn off automatically? Was the battery
fully charged to begin with? All these conditions affect how long the
charge lasts.
For more information on maximizing battery power, see “Maximizing
Battery Life” in chapter 4.
User's Manual
7-4
1 Last Saved on 30/05/2003 13:57
Keyboard Problems
If, when you type, strange things happen or nothing happens, the
problem may be related to the keyboard itself.
The keyboard produces unexpected characters
A keypad overlay may be on. If the numeric keypad or cursor control light
is on, press Fn and F10 simultaneously to turn off the cursor control light
or press Fn and F11 simultaneously to turn off the numeric keypad light.
If the problem occurs when both the keypad overlays are off, make sure
the software you are using is not remaking the keyboard.
Refer to the software’s documentation and check that the program does
not assign different meanings to any of the keys.
You have connected an external keyboard and the
operating system displays keyboard error messages
If you have a second keyboard, try it. If it works, the first keyboard may
be defective or incompatible with your computer.
Nothing happens when you press the keys on the
external keyboard
If you plugged the external USB keyboard in while the computer was
turned on, your computer may have failed to recognize it. Using the
Touch pad or pointing device to click Start, then click Turn Off
Computer. When Microsoft® Windows® operating system displays the
Turn Off Computer dialog box, select Restart and click OK. The
computer will restart and recognize the device.
The keyboard locks and the computer will not restart
Push the power button for more then 4 seconds. The computer will turn
off. Then push the power button again to turn on the computer.
Restarting the computer in this manner may cause irreparable loss of
data. It is not recommended you do this unless absolutely warranted.
User's Manual
7-5
1 Last Saved on 30/05/2003 13:57
Display Problems
Here are some typical display problems and their solutions:
The display is blank
Display Auto Off may have gone into effect. Press any key to activate the
screen.
You may have activated the instant security feature by pressing Fn and
F1 simultaneously. If you have registered a password, type it and press
any key. If no password is registered, simply press any key. The screen
reactivates and allows you to continue working.
If you are using the built-in screen, make sure the display priority is not
set for an external monitor. To do this, press Fn and F5 simultaneously
(once). If this does not correct the problem, press Fn and F5
simultaneously again to return the display priority to its previous setting.
If you are using an external monitor or television:
■ Check that the monitor or television is turned on.
■ Check that the monitor or television’s power cable is firmly plugged
into a working power outlet.
■ Check that the cable connecting the external monitor or television to
the computer is firmly attached.
■ Try adjusting the contrast and brightness controls on the external
monitor or television.
■ Press Fn and F5 simultaneously to make sure the display priority is
not set for the built-in screen.
■ If no image appears on the screen after switching displays, press
Fn + Spacebar simultaneously to change the resolution.
The screen does not look right
You can change the display settings by clicking a blank area of the
desktop with the Touch pad secondary button, then clicking Properties.
This causes operating system to open the Display Properties dialog box.
The Appearance tab of this dialog box allows you to choose the colours
for the screen. The Settings tab allows you to choose the screen
resolution.
The built-in screen flickers
Some flickering is a normal result of the way the screen produces colours.
To reduce the amount of flickering, try using fewer colours.
To change the number of colours displayed:
1. Point at the desktop and click with the secondary button.
2. Click Properties, and then Settings.
3. Change the Colour quality option and click OK.
For more information, see Windows Help.
User's Manual
7-6
1 Last Saved on 30/05/2003 13:57
A message indicates a problem with your display
settings and that the adapter type is incorrect or the
current settings do not work with your hardware
Reduce the size of the colour palette to one that is supported by the
computer’s internal display. To change the display properties:
1. Point at the desktop and click with the secondary button.
2. Click Properties, and then Settings.
3. Change settings and click OK.
For more information, see Windows Help.
Disk Drive Problems
Problems with the hard disk or with a diskette drive usually show up as an
inability to access the disk or as sector errors. Sometimes a disk problem
may cause one or more files to appear to have garbage in them. Typical
disk problems are:
You are having trouble accessing a disk, or one or more
files appear to be missing
Make sure you are identifying the drive by its correct name (A: or C:).
Run Error-checking to check for file system errors and bad sectors on
your hard disk.
To run Error-checking:
1. Click Start and open My Computer.
2. Click the drive you want to test.
3. On the File menu, click Properties.
4. On the Tools tab, under Error-checking, click Check Now.
5. Under Check disk options, select the Scan for and attempt
recovery of bad sectors check box.
All files must be closed for this process to run. If the drive is currently in
use, a message box will appear prompting you to indicate whether or not
you want to reschedule the disk checking for the next time you restart
your system. Then, the next time you restart your system, disk checking
will run. Your drive will not be available to perform other tasks while this
process is running.
Your hard disk seems very slow
If you have been using your computer for some time, your files may have
become fragmented. Run Disk Defragmenter. To do this, click Start, point
to All Programs, Accessories, System Tools, and click Disk
Defragmenter.
User's Manual
7-7
1 Last Saved on 30/05/2003 13:57
Your data files are damaged or corrupted
Refer to your software documentation for file recovery procedures. Many
software packages automatically create backup files.
You may also be able to recover lost data using utility software, which is
available from your dealer.
Some programs run correctly but others do not
This may be a software configuration problem. If a program does not run
properly, review the program’s hardware configuration requirements.
Most software documentation lists the minimum hardware requirements.
See “Features and Specifications” (appendix B) to review the hardware
configuration of this computer.
A disk will not go into the diskette drive
You may already have a diskette in the drive. Make sure the drive is
empty.
You may be inserting the diskette incorrectly. Hold the label of the disk
with the hub side facing down, and insert it so that the metal head
window cover goes into the drive first.
The metal cover or a loose label may be obstructing the path into the
drive. Carefully inspect the diskette. If the metal cover is loose, replace
the diskette. If the label is loose, replace the label and try inserting the
diskette again.
The computer displays the Non-system disk or disk
error message
If you are starting the computer from the hard disk make sure there is no
diskette in the diskette drive.
If you are starting the computer from a diskette, the diskette in the drive
does not have the files necessary to start the computer. Replace it with a
bootable diskette.
The drive can not read a diskette
Try another diskette. If you can access the second diskette, the first
diskette (not the diskette drive) is probably causing the problem. Run the
Check Disk tool on the faulty diskette (for instructions, see “Disk drive
problems” earlier in this section).
User's Manual
7-8
1 Last Saved on 30/05/2003 13:57
CD-ROM Drive Problems
You cannot access a CD in the drive
Make sure the CD-ROM tray has closed properly. Press gently until it
clicks into place.
Open the CD-ROM tray and remove the CD. Make sure the CD-ROM tray
is clean. Any dirt or foreign object can interfere with the laser beam.
Examine the CD to see whether it is dirty. If necessary, wipe it with a soft
clean cloth dipped in water or a neutral cleaner.
Replace the CD in the drawer. Make sure it is laying flat, label side
uppermost. Press down until the CD-ROM disc locks on the spindle.
Close the CD-ROM tray carefully, making sure it has shut completely.
You press the CD-ROM eject button, but the CD-ROM
tray does not slide out
Make sure the computer is connected to a power source and turned on.
The CD-ROM drive eject mechanism requires power to operate.
If you need to remove a CD and cannot turn on the computer, use a
narrow object, such as a straightened paper clip, to press the manual
eject button. This button is in the small hole next to the CD-ROM eject
button on the right side of the computer.
Some CDs run correctly, but others do not
If the problem is with a data CD, refer to the software’s documentation
and check that the hardware configuration meets the program’s needs.
The colour of the materials used to make the CD can affect its reliability.
Silver-collared CDs are the most reliable, followed by gold-coloured CDs.
Green-coloured CDs are the least reliable.
Sound System Problems
You do not hear any sound from the computer
Adjust the volume control.
If you are using an external headphone or speakers, check that they are
securely connected to your computer.
The computer emits a loud, high-pitched noise
This is feedback between the microphone and the speakers. It occurs in
any sound system when input from a microphone is fed to the speakers
and the speaker volume is too loud. Adjust the volume control.
User's Manual
7-9
1 Last Saved on 30/05/2003 13:57
PC Card Problems
PC Cards (PCMCIA-compatible) include many types of devices, such as a
removable hard disk, additional memory, fax/modem, or pager.
Most PC Card problems occur during installation and setup of new cards.
If you’re having trouble getting one or more of these devices to work
together, several sections in this chapter may apply.
■ Resource conflicts can cause problems when using PC Cards.
■ If the device is a modem, see “Modem problems” later in this chapter.
PC Card Checklist
■ Make sure the card is inserted properly into the slot.
■ Make sure all cables are securely connected.
■ Make sure the computer is loading only one version of Card and
Socket Services.
■ Occasionally a defective PC Card slips through quality control. If
another PCMCIA-equipped computer is available, try the card in that
machine. If the card malfunctions again, it may be defective.
Resolving PC Card Problems
Here are some common problems and their solutions:
The slots appear to be dead and PC Cards that used to
work no longer do
Check the PC Card status:
Properties.
®
Windows operating system displays the System Properties dialog
box.
2. Click the Hardware Tab, then the Device Manager button.
3. Double-click the device listed as your PC Card.
®
Windows operating system displays your PC Card’s Properties dialog
box. This dialog box contains information about your PC Card
The computer stops working when you insert a PC Card
The problem may be caused by an I/O (input/output) conflict between the
PCMCIA socket and another device in the system. Use Device Manager
to make sure each device has its own I/O base address.
Since all PC Cards share the same socket, each card is not required to
have its own address.
User's Manual
7-10
1 Last Saved on 30/05/2003 13:57
Hot swapping (removing one PC Card and inserting
another without turning the computer off) fails
Follow this procedure before you remove a PC Card:
1. Click the PC Card icon on the taskbar.
2. Click Safely remove xxxx, where xxxx is the identifier for your PC
Card.
®
Windows operating system displays a message that you may safely
remove the card.
3. Remove the card from the slot.
The system does not recognize your PC Card or
PCMCIA socket controller
This problem may be caused by a low battery. Replace the battery with a
fully-charged one or charge the battery fully as follows:
1. Make sure the computer is not in Standby.
3. Connect the AC adapter and power cable.
4. Keep the computer plugged in for about four hours with the power
turned off.
If power is not the problem, try removing the card, inserting it again, and
reinstalling it using the procedure in “Inserting PC Cards” in chapter 3.
The problem may also be caused by a conflict with any additional
memory in your system. If you recently installed a memory expansion
card, turn off the computer, remove the memory, turn on the computer
and try the PC Card again.
A PC Card error occurs
Reinsert the card to make sure it is properly connected.
If the card is attached to an external device, check that the connection is
secure.
Refer to the card’s documentation, which should contain a
troubleshooting section.
User's Manual
7-11
1 Last Saved on 30/05/2003 13:57
Printer Problems
This section lists some of the most common printer problems.
The printer will not print
Check that the printer is connected to a working power outlet, turned on
and ready (on line).
Make sure the printer cable is firmly attached to the computer and the
printer.
If your printer is ECP- or IEEE 1284-compliant, make sure you have an
IEEE 1284 printer cable.
Check that the printer has plenty of paper. Some printers will not start
printing when there are just two or three sheets of paper left in the tray.
Run the printer’s self-test to check for any problem with the printer itself.
Make sure you installed the proper printer driver.
Try printing another file. For example, you could create and attempt to
print a short test file using Notepad. If a Notepad file prints correctly, the
problem may be in your original file.
Contact your network administrator if the printer is on your network.
The printer will not print what you see on the screen
Many programs display information on the screen differently from the way
they print it. See if your program has a print preview mode. This mode
lets you see your work exactly as it will print. Contact the software
manufacturer for more information.
User's Manual
7-12
1 Last Saved on 30/05/2003 13:57
Modem Problems
This section lists common modem problems.
The modem will not receive or transmit properly
Make sure the RJ-11 cable (the one that goes from the modem to the
telephone line) is firmly connected to the modem’s RJ-11 jack and the
telephone line socket.
Check the serial port settings to make sure the hardware and software
are referring to the same COM port.
Check the communications parameters (band rate, parity, data length and
stop bits) specified in the communications program. It should be set up to
transmit at 300, 1200, 2400, 4800, 9600, 14400, 28800, 33600, 56000 bps
(bits per second) or higher. Refer to the program’s documentation for
information on how to change these settings.
To check the modem’s settings and communications parameters:
Properties.
Windows® operating system displays the System Properties dialog
box.
2. Click the Hardware Tab, then the Device Manager button.
3. Click on the modem name listed under Modems.
®
Windows operating system displays your modem’s Properties dialog
box. This dialog box contains information about your modem
The modem is on, set up properly and still does not
transmit or receive data
Make sure the line has a dial tone. Connect a telephone handset to the
line to check this.
The other system may be busy or offline. Try making a test transmission
to someone else.
User's Manual
7-13
1 Last Saved on 30/05/2003 13:57
Develop Good Computing Habits
■ Make sure you are prepared.
■ Save your work frequently.
You can never predict when your computer will lock forcing you to close
a program and lose unsaved changes. Many software programs build in
an automatic backup, but you should not rely solely on this feature. Save
your work!
■ On a regular basis, back up the information stored on your hard disk.
Here are two ways you can do this:
®
®
■ Copy files to diskette in Microsoft Windows operating system.
■ Connect a backup device ( e.g. CD-R) to the system and use
specialized software to copy everything on the hard disk to a backup
device.
Some people use a combination of these methods, backing up all files to
backup device weekly and copying critical files to diskette on a daily
basis.
If you have installed your own programs, you should back up your
programs as well as your data files. If something goes wrong that requires
you to format your hard disk and start again, reloading all your programs
and data files from a backup will save time.
■ Please check every three months to make sure the fan inlet is
unobstructed and clean the inlet if necessary.
■ Read the user’s guide.
It’s very difficult to provide a fail-safe set of steps you can follow every
time you experience a problem with the computer. Your
ability to solve problems will improve as you learn about how the
computer and its software work together.
Get familiar with all the user’s guide provided with your computer, as well
as the manuals that come with the programs and devices you purchase.
Your local computer store or book store sells a variety of self- help books
you can use to supplement the information in the manuals.
■ If problem-solving is taking a long time, take a break.
If you have been fighting to solve a problem for a long time, you are
probably frustrated by now. Stand up and take a deep breath. Often, you
can find a new solution to a problem just by stepping away from it for a
few moments.
User's Manual
7-14
1 Last Saved on 30/05/2003 13:57
If You Need Further Assistance
If you have followed the recommendations in this chapter and are still
having problems, you may need additional technical assistance. This
section contains the steps to take to ask for help.
Before you call
Since some problems may be related to the operating system or the
program you are using, it is important to investigate other sources of
assistance first.
Try the following before contacting TOSHIBA:
■ Review the troubleshooting information in your Microsoft® Windows®
documentation.
■ If the problem occurs while you are running a program, consult the
program’s documentation for troubleshooting suggestions. Contact
the software company’s technical support group for their assistance.
■ Consult the dealer from whom you purchased your computer and/or
program. Your dealer is your best source for current information.
Contacting TOSHIBA
If you still need help and suspect that the problem is hardware related,
TOSHIBA offers a variety of resources to help you. Please refer to
appendix E for TOSHIBA support information.
User's Manual
7-15
1 Last Saved on 30/05/2003 13:57
Hot Keys
Satellite P20
Appendix A
Hot Keys
Hot keys are keys that, when pressed in combination with the Fn key, turn
system functions on and off. Hot keys have an icon label on the key
indicating the option or feature the key controls.
Volume mute
Turns the volume off and on. When you press
these keys, the current setting is shown in a
window.
Instant security
Blanks the screen to prevent others from
accessing your data. To restore the screen and
original settings, press any key or use the Touch
pad. If you have set a screen saver password, a
dialog box appears. Enter the password and
click OK. If no screen saver password is set, the
screen is restored when you press any key or
use the Touch pad.
Power save mode
Changes the power save mode. Press Fn+F2
once to display the Power Save Mode in a
window. Press the hotkeys again to change the
setting. You can also change this setting through
the AC Power or Battery Power items of the
Power Save Modes tab in the TOSHIBA Power
Management Utility.
Standby
The computer enters Standby. To avoid entering
Standby unexpectedly, a dialog box appears for
verification. However, if you uncheck the dialog
box, it will not appear the next time.
Hibernate
The computer enters Hibernate. To avoid
entering Hibernate unexpectedly, a dialog box
appears for verification. However, if you activate
the checkbox in the dialog box, it will not appear
the next time.
Display selection
Changes the active display device. When you
press these hotkeys a dialog box appears. Only
selectable devices are displayed.
User's
Manual
User's Manual
A-1
1 Last Saved on 30/05/2003 13:57
Hot Keys
Brightness down
Decreases the display brightness. When you
press these hotkeys, the current setting is
displayed for two seconds by a pop-up icon.
You can also change these settings through the
Monitor Brightness item of a specific item in the
Power Save Modes tab of the TOSHIBA Power
Management Utility.
Brightness up
Increases the display brightness. When you
press these hotkeys, the current setting is
displayed for two seconds by a pop-up icon.
You can also change these settings through the
Monitor Brightness item of a specific item in the
Power Save Modes tab of the TOSHIBA Power
Management Utility.
Wireless Device
Controls
Functions only if the Wireless Communications
Switch has been turned on. The Wireless
Communication LED on the system indicator
panel lets you know when the wireless devices
are active. Pressing this key combination lets
you select a device mode.
Touch pad
Enables or disables the Touch pad function.
When you press these hotkeys, the current
setting is changed and displayed as an icon.
Cursor keypad on/off Pressing this hot key can enable/ disable the
embedded cursor keypad. Numeric lock state is
logically disabled. See chapter 3 for more on the
embedded keypads.
Numeric keypad
on/off
Pressing this hot key can enable/ disable the
embedded numeric keypad. Numeric lock state
is logically enabled. See chapter 3 for more on
the embedded keypads.
Scroll lock on/off
This hot key turns the scroll lock feature on and
off.
Change resolution
Changes the current screen resolution.
The cursor and numeric keypads are set to off whenever you restart or
turn your computer on. Brightness settings are likewise overridden during
Start-up by those set in the Power Management Utility. For TOSHIBA
Power Management Utility, refer to chapter 5.
User's Manual
A-2
1 Last Saved on 30/05/2003 15:18
Features And Specifications
Satellite P20
Appendix B
This appendix lists the features of the Satellite P20 series computers and
summarizes their specifications.
CPU
■ 2,53 GHz Intel® Pentium® 4 processor 2,53 GHz
®
®
■ 2,66 Intel Pentium 4 processor 2,66 GHz
with 533 MHz system bus,
or
■ 2,40C GHz / 2,60C GHz / 2,80C GHz / 3.0 GHz / 3.0C GHz
with 800 MHz system bus and Hyper-Threading Technology
Other processors may be introduced in the future.
Chip Set
■ Intel 865 PE
■ Intel 82801 EB I/O Controller HUB
■ PC87591L for Keyboard Controller, Battery Management Unit, and
RTC
■ T7L58XB for Card Bus PCMCIA controller and SD controller
■ nVIDIA GeForce FX Go5200 graphics controller
■ ALC202 for AC97 CODEC
■ OZ168 for Direct CD play controller
■ 8101L for LAN controller
Memory
■ On board with two 200-pin +2.5V SO-DIMM connector supporting
DDR memory cards. Maximum upgradable to 2 GB by two 1 GB
SO-DIMM modules
■ 512 KB L2 Cache on CPU
■ External 32MB or 64MB VGA DDR RAM
User's
Manual
User's Manual
B-1
1 Last Saved on 30/05/2003 13:57
BIOS
■
■
■
■
■
■
■
512KB Flash ROM for system BIOS
Password protection (System)
Windows XP ready with PnP
Suspend to RAM/Disk
Hot keys for system control
Refreshable
Complete ACPI 1.0b Function
Power
■ 12 cells Li-Ion 18650 size smart battery Pack with 14.8V x 6450 mAh
capacity
■ 12 hours or longer charge time to 100% capacity on Li-Ion Battery
when the system is on
■ Approximately 4 hours charge time to 100% capacity on Li-Ion
Battery when the system is off
One 2.5", 9.5mm Hard Disk, support with
30GB/40GB/60GB/80GB
■ Bus Master IDE
■ 9.5mm, 2.5” HDD Support
■ Support Ultra DMA100
Storage Devices (HDD/FDD/Optical disk drives)
(depending on model)
■
■
■
■
■
■
12.7mm, 1.44MB FDD device
12.7mm height DVD-R/-RW device
12.7mm height DVD-ROM device
12.7mm height DVD Multi device
12.7mm height CD-RW/DVD-ROM device
Second HDD Drive
User's Manual
B-2
1 Last Saved on 30/05/2003 13:57
Options
■
■
■
■
■
■
■
■
■
■
■
■
■
■
PC2100 256MB / 512MB / 1GB DDR module
Module Bay HDD adaptor
HDD pack
CD-RW/DVD-ROM Drive Kit
DVD Multi Drive Kit
DVD-R/-RW Drive Kit
FDD Drive Kit
USB FDD Kit
Wireless LAN card (802.11b)
Wireless LAN card (802.11a/b)
AC Adaptor
Battery Pack
Bluetooth SD Card
Remote Control
Touch pad Point Device
■ Left Button
■ Right Button
I/O Ports (Depending on the model bought)
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
One 25-pin parallel port, EPP/ECP capability
One 15-pin external monitor port, supports DDC 2B
One TV-out port
One Microphone Jack
One Line-In Jack
One Headphone Jack
One DC-IN
One SD Card Slot
Four USB ports
One RJ11 jack
One RJ45 jack
VR for volume control
One FIR port
One Remote Control Receiver Port
One i.LINK (IEEE 1394) port
User's Manual
B-3
1 Last Saved on 30/05/2003 13:57
PCMCIA Card
■
■
■
■
■
One type III card socket or two type II card sockets
MODEM/LAN card
ATA Card
Card bus card
ACPI 1.0b Compliant
Power Management Function
■ Standby mode, Suspend to RAM or Suspend to Disk mode, by time
out or by hot key
■ HDD Local Stand-By mode by time out
■ LCD Local Stand-By mode by time out
■ Low battery alarm by beep
■ Auto-backlight off when LCD cover closed
■ Full ACPI 1.0b supported
■ LCD Auto-DIM mode by time out
Switches
■
■
■
■
■
■
■
■
■
Power Button
One Internet Button
One TOSHIBA Console Button
One TV Out Button
CD/Digital Mode Button
Eject/Stop Button
Play/ Pause Button
Forward Button
Reverse Button
AC Adapter
■ Universal AC adapter module: 90-264V AC, 47-63HZ, 120W
Security
■ Boot-up password protection
■ Single level password architecture (Supervisor)
User's Manual
B-4
1 Last Saved on 30/05/2003 13:57
Power Cable Connectors
Satellite P20
Appendix C
Power Cable Connectors
The Satellite computer features a universal power supply you can use
worldwide. This appendix shows the configuration of typical AC power
cord plugs and sockets in various parts of the world.
USA and Canada
UL approved
CSA approved
Australia
AS approved
United Kingdom
BS approved
Europe
VDE approved/NEMKO approved
User's
Manual
User's Manual
C-1
C-1
1 Last Saved on 03/06/2003 10:50
Display Modes
Satellite P20
Appendix D
Display Modes
This appendix is a table of the display mode options of your computer’s
nVidia Graphics Controller when display device is set to an external
monitor.
CRT Display
Resolution
Colour Depth
Refresh Rate (Hz)
800x600
16
32
60 70 72 75 85
60 70 72 75 85
1024x768
16
32
60 70 72 75 85
60 70 72 75 85
1280x1024
16
32
60 70 72 75 85
60 70 72 75 85
1400x1050
16
32
60 70 72 75 85
60 70 72 75 85
1600x1200
16
32
60 70 72 75 85
60 70 72 75 85
1920x1440
16bpp
32bpp
60 70 72 75
60
2048x1536
16bpp
32bpp
60
60
User's
Manual
User's Manual
D-1
D-1
1 Last Saved on 30/05/2003 13:57
The TOSHIBA International Warranty
Satellite P20
Appendix E
The TOSHIBA International
Warranty
The TOSHIBA International Warranty is a service policy on the parts and
repair on your TOSHIBA portable personal computer which is
automatically available to purchasers of the computer.
The cover is assured in major industrial countries of the world. It means
that wherever you take your TOSHIBA mobile PC in this area, you will
never be left without help should any problems arise.
For more information on the warranty coverage please refer to your
warranty booklet supplied with your Notebook.
What the warranty covers
The Warranty covers the computer in the standard version, including the
AC adaptor. Batteries, modems, memory expansion kits and other
TOSHIBA branded options, as well as third party expansion boards are
NOT covered by this warranty. For information concerning warranties for
these products, please consult your dealer.
If you would like to use the international warranty, please register for this
warranty at the following Internet website:
http://www.toshiba-europe.com/computers/warranty
Once your registration has been received by TOSHIBA the warranty
entitlement of your Notebook can be checked on the following Internet
website:
http://gedb.toshiba.com
On the following pages is a list of the TOSHIBA Authorised Service
Providers who can be contacted if a claim on the warranty needs to be
made.
If users need further addresses in eastern Europe or outside Europe,
these are available from the national or European companies.
The countries to which the international warranty applies can be found
using the TOSHIBA Global ASP locator.
Click: Support, Find an Authorised Service Provider
User's
Manual
User's Manual
E-1
E-1
1 Last Saved on 30/05/2003 13:57
TOSHIBA's Worldwide Computer Representatives
Australia
TOSHIBA (Australia) Pty. Limited
84-92 Talavera Road, North Ryde NSW 2113
Tel: +61-2-9887-3322
Fax: +61-2-9888-3664
http://www.isd.toshiba.com.au
Austria
TOSHIBA Europe GmbH
Leibnizstr. 2
93055 Regensburg
Tel: 0800-29 74 88
Fax:+49-(0)941-780 79 25
www.computer.toshiba.at
Azerbaijan
AZEL (Azerbaijan Electronics)
Floor 5, 65 Fizuli Str.
370014 Baku
Tel: +99412-974040
Fax: +99412-974042
http://www.azel.net
Belgium
TOSHIBA Information Systems Belgium
Excelsiorlaan 40
1930 Zaventem
Tel: +32-900-10990
Fax: +32-2-7253030
www.toshiba.be
Bulgaria
IMPEX Sofia Ltd.
12, Anton Naydenov Street, PO Box 184,
1710 Sofia
Tel: +359-2-962-1219
Fax: +359-2-962-5062
Canada
TOSHIBA of Canada Ltd.
191 McNabb Street
Markham, Ontario L3R-8H2
Tel: +1-905-470-3500
Fax: +1-905-470-3487
http://www.toshiba.ca
Czech
Republic
CHG Service , s.r.o.
Videnska 102
619 00 Brno
Tel: +420-5-4742-6581
Fax: +420-5-4742-6590
http:// www.chgservice.cz
Denmark
Scribona TOSHIBA Digital Media
Hovedvejen 9
DK-2600 Glostrup
Tel: +45-3823-7600
Fax: +45-3823-7601
www.toshiba-dm.com
Egypt
El Araby Co. for Trading and Manufactoring
P.O. Box 1224/Off Beirut St.
10, Mohammed Sabry Abolaalm Street
Kourba , Heliopolis / Cairo 11511
Tel: +202-291-6989
Fax: +202-291-6454
http://www.elaraby.com.eg
Estonia
ServiceNet
Pärnu str. 142
11317 Tallinn
Tel: +372-6504-949
Fax: +372-6504-948
http://www.servicenet.ee
Finland
Scribona Suomi OY / TOSHIBA Digital Media
Sinimäentie 8A,P.O.Box 83
02630 ESPOO
Tel: +358-9-5272555
Fax: +358-9-5272500
http://www.toshiba-dm.com
France
TOSHIBA Systèmes (France) S.A.
7 Rue Ampère ; B.P. 131
92804 Puteaux Cedex
Tel.: +33-8 92 69 70 92
Fax: +33-1-4728-2247
http://www.pc.toshiba.fr
Germany
TOSHIBA Europe GmbH
Leibnizstraße 2
93055 Regensburg
Tel: 01805-23 16 32
Fax: +49-(0)941-7807-925
www.computer.toshiba.de
Greece
Ideal Electronics S.A.
25 Kreontos Str.
10442 Sepolia, Athens
Tel: +30-210-5193950
Fax: +30-210-5193960
http://www.ideal.gr
User's Manual
E-2
1 Last Saved on 30/05/2003 13:57
Hungary
Technotrade Informatikai Rt.
Öv u, 185,
1147 Budapest
Tel: +36-1-467 6100
Fax: +36-1-252 6470
http://www.technotrade.hu
Ireland
TOSHIBA Information Systems (U.K.) Limited,
TOSHIBA Court, Weybridge Business Park,
Addlestone Road, Weybridge, Surrey KT15 2UL
Tel.: +353 (0)1248 1 248
Fax: + 44 (0)8702 202 303
www.toshiba.co.uk/computers/
Israel
Mafil Technologies (3000) Ltd
8 Bareket Street
49517 Petah Tikwa
Tel: +972-3-918-3333
Fax: +972-3-924-1310
http://www.mafil.co.il
Italy
Progetto Elettronica 92.S.p.A
Via de Gasperi 88a
20017 Mazzo di Rho
Tel: +39-02-9397-5551
+39-02-939 75678
Fax: +39-02-9397-5299
http://www.pe92.it
Japan
TOSHIBA Corporation, IOPC
1-1, Shibaura 1-Chome, Minato-KU
Tokyo 105-01
Tel: +81-3-3457-5565
Fax: +81-3-5444-9262
http://www.toshiba.co.jp
Jordan
Scientific & Medical Supplies Co.
Jabal Amman, 1st Circle , Al Hayyek Street,
Opposite to Housing Bank
11118 Amman
Tel: +962 (6) 4624907
Fax: +962 (6) 462858
Kuwait
Arabian Business Machines Co.
Salhiya-Sulaiman AL Laheeb Building 3
P.O. Box 29961, 13160 Safat
Tel: +965-242-9154
244-5373/-5369
Fax: +965-241-4399
www.abm-kuwait.com
Latvia
Servicenet LV
Bullu Str 9
LV1055 Riga
Tel: +371-7052079
Tel.: +371 7460399
Fax: + 371-7460299
http://www.servicenet.lv
Lebanon
Pcdealnet
Diab Bldg. Mkalles Rd., P.O. Box 11-316
Beirut
Tel: +961-1-682-956
Fax: +961-1-682-955
www.pcdealnet.com
Lithuania
Servicenet LT
verslo g. 6
Kumpiu km. Domeikava
4302 Kauno raj.
Tel: + 370 37 757586
Fax: + 370 37 757541
http://www.servicenet.lt
Luxemburg
See 'Netherlands'
Malta
Tabone Computer Centre Limited
111 Old Railway Track
HMR-16 St Venera
Tel: +356-49 36 04
Fax: +356-49 36 03
http://www.tabone.com.mt
Morocco
C.B.I. Lotissement Attoufik,
Rue No 1 Immeuble 29, Sidi Maarouf
20190 Casablanca/ Maroc
Tel: +212- 22 43 71 60/61
Fax: +212-22 43 71 88
Netherlands
TOSHIBA Information Systems Benelux B.V.
Rivium Boulevard 41
2909 LK Capelle a/d IJssel
Tel: +31-0900-1000-1000
Fax: +31-10-2882-390
http://www.toshiba.nl
User's Manual
E-3
1 Last Saved on 30/05/2003 13:57
Norway
Scribona Norway A/S
Stålfjæra 20, P.O.Box 51, Kalbakken
0901 Oslo
Tel: +47-22-897-189
Fax: +47-22-897-166
http://www.toshiba-dm.com
Oman
(Sultanate of
Oman)
Bahwan IT
Sarco Building, Ground Floor No. 459, Way
No. 3109 Al Noor Street,
Ruwi 113 Muscat
Tel.: + 968 790191-117
Fax: +968-790 192
http://www.bahwanit.com
Poland
AC Serwis Sp. Z o. o. ul.
Przasnyska 6b,
01-756 Warszawa
Tel: +48- 22-56-08-205
Fax: +48- 22-56-08-20
http://www.acserwis.com.pl
Portugal
TOSHIBA Information Systems Portugal
Edificio D. Pedro I Quinta da Fonte
2780-730 Paço d’Arcos
Tel: +351-707265265
Fax: +351-21-000-1675
http://www.toshiba.pt
Qatar
Mannai Trading Company
Rayyan Road, P.O. Box 76
Doha
Tel: +974 441-2555
Fax: +974 444-5413
Qatar
Jarir Bookstore Qatar
Al Maha Center, Ramada Crossing, Salwa Road,
P.O. Box 24824, Doha
Tel: +974 444 0212
Fax: +974 444 04 32
www.jarirbookstore.com
Romania
Scop Computers SRL
162 Barbu Vacarescu St, Sector 2
71424 Bucharest
Tel: +40-1-231-4602
Fax: +40-1-231-4606
http://www.scop.ro
Russia
AC SERSO
Sovetskoi Armii st. 5
127018 Moscow
Tel: +7 - 095 284 5577
Tel: +7-095 105-8161
Fax: +7-095 284 5880
http://www.cepco.ru
Russia
Microbit SERSO
Izmailovskiy Pr.2
S.Petersburg 198005
Tel.: +7 812 327-5700
www.microbit.ru
Saudi Arabia
Arabian Business Machines Co.
Dareen Center, Ahsaa Road
P.O. Box 2006
11451 Riyadh
Tel: +966-1 478 4909
Fax: +966-1 477 7803
www.olayangroup.com
Saudi Arabia
Jarir Bookstore
P.O. Box 3196
Olaya Street
11471 Riyadh
Tel: +966-1 462 6000
Fax: +966-1 462 9500
www.jarirbookstore.com
Slovakia
HT Computers a.s.
Dobrovicova 8
81109 Bratislava
Tel: +421-2-59334 550
Fax: +421-2-59334 555
http://www.htc.sk
Slovenia
Inea d.o.o.
Stegne 11,
1117 Ljubljana
Tel: +386-1-513-81-00
Fax: +386-1-513-81-70
http://www.inea.si
User's Manual
E-4
1 Last Saved on 30/05/2003 13:57
South Africa
CS IT Solutions, CS Holdings Office Park
Block D, 241 Third Road
PO Box 786691
1685 Midrand
Tel: +27 (0) 11 205-7000
Fax: +27-0-11-205-8586
http://www.cs.co.za/it.htm.
South Africa
RECTRON (Pty) Ltd.
152 15th Road, Randjespark
Midrand, 1685
Tel: +27-0-11-203-1000
Fax: +27-0-11-203-1100
Spain
TOSHIBA Information Systems (España) S.A.
Parque Empresarial San Fernando
Edificio Europa, 1a Planta, Escalera A
28830 (Madrid) San Fernando de Henares
Tel: +34-91-6606-700
Fax: +34-91-6606-760
http://www.toshiba.es
Sweden
TOSHIBA Digital Media
Sundbybergsvägen 1, Box 1374
171 27 Solna
Tel: +46-200-212100
Fax: +46-8-734-4656
http://www.toshiba.se
Switzerland
TOSHIBA Europe Gmbh, Swiss Sales branch,
Chriesbaumstrasse 4
Postfach 171
CH-8604 Volketswil
Tel: +41-848-845250
Fax: +41-1-908 5658
http://www.toshiba.ch
Turkey
Bekom Bilgisayar Sistemleri San. ve TIC. A.S.
Burhaniye Mah. Neset Bey Sok. No:7
USKUDAR, ISTANBUL
Tel: +90 216 422 40 50
Fax: +90 216 422 55 20
http://www.toshibatr.com
Ukraine
DKT-SERSO
Lesya Ukrainka blv, 26
01133 Kiev
Tel: +380-44-573-9627
Fax: +380-44-254-4646
http://www.dkt-cepco.com.ua
United Arab
Emirates
Tel: +971 4 351 5004
Al-Futtaim Electronics
Fax: +971 4 351 4254
P.O. Box 5866, Bin Ham Building, Mezzanine
Floor Adjacent to BurJuman Centre, Trade Centre http://www.toshibauae.com
Road, Dubai
United Arab
Emirates
Al-Futtaim Electronics, Central Services Operation Tel: +971 4 282 5112
Garhound Area, P.O. Box:531 Dubai, U.A.E.
Fax: +971 4 282 4094
United Arab
Emirates
Al-Futtaim Electronics, Central Services Operation Tel: +971 2 673 3004
Mina-Area, P.O. Box:26605, Abudhabi, U.A.E.
Fax: +971 2 673 3809
United
Kingdom
TOSHIBA Information Systems (UK) Ltd.
TOSHIBA Court, Weybridge Business Park
Addlestone Road, Weybridge
Surrey KT15 2UL
United States TOSHIBA America Information Systems, Inc.
9740 Irvine Blvd., P.O. Box 19724
Irvine, CA 92713-9724
Yugoslavia
CT Computers d.o.o.
Vladimira Popovica 6
11070 Beograd
Tel: +44-(0)8702 202202
Fax: + 44-(0)8702 202303
www.toshiba.co.uk/computers/
Tel: +1-949-583-3000
Fax: +1-949-583-3345
http://www.toshiba.com
Tel: +381-11-311-2060
Fax: +381-11-311-2060
http://www.comtrade.co.yu
User's Manual
E-5
1 Last Saved on 30/05/2003 13:57
TOSHIBA addresses for the Internet/World Wide Web
TOSHIBA Europe
http://www.toshiba-europe.com
TOSHIBA Japan
http://www.toshiba.co.jp
TOSHIBA America
http://www.toshiba.com
TOSHIBA Canada
http://www.toshiba.ca
User's Manual
E-6
1 Last Saved on 30/05/2003 13:57
If Your Computer Is Stolen
Satellite P20
Appendix F
Always take care of your computer and try to prevent it from being stolen.
You are the owner of a valuable technical device, which may be highly
attractive to thieves, so please do not leave it unattended in a public
place. To further help protect against theft, security cables can be bought
for use with your notebook when it is being used at home or in the office.
Make a note of your computer’s machine type, model number, and serial
number, and put it in a safe place. You will find this information on the
underside of your notebook. Please also keep the receipt of the computer
you purchased.
Should your computer be stolen, however, we’ll help you try to find it.
Before contacting TOSHIBA, please prepare the following information
which is necessary to uniquely identify your computer:
■ In which country was your computer stolen?
■ What type of machine do you have?
■ What was the model number (PA number)?
■ What was the serial number (8 digits)?
■ When was it stolen, i.e. date?
■ What was the warranty seal number (if available)?
■ What is your address, phone, and fax number?
To register the theft, please follow these procedures:
■ Fill in the TOSHIBA Theft Registration form (or a copy of it) below.
■ Attach a copy of your receipt showing where your computer was
purchased.
■ Either fax or send the receipt and registration form to the address
below.
Your registration will be entered in a database, which is used to track
TOSHIBA computers at our service points around Europe.
User's
Manual
User's Manual
F-1
1 Last Saved on 30/05/2003 13:57
TOSHIBA Theft Registration
Send to:
Fax number:
TOSHIBA Europe GmbH
Technical Service and Support
Leibnizstr. 2
93055 Regensburg
Germany
+49 (0) 941 7807 925
Country stolen:
Machine type:
(e.g. Satellite P20)
Model number:
(e.g. PSA10 YXT)
Serial number:
(e.g. 70123456E)
Date stolen:
Warranty seal:
(e.g. 9813 123456 049)
Owner’s details
Name:
Company:
Street:
Postal Code/City:
Country:
Phone:
Fax:
User's Manual
F-2
1 Last Saved on 30/05/2003 13:57
Index
Satellite P20
Index
A
AC adapter
connecting, 2-5
Additional Options, 6-8
Audio Devices
connecting, 6-6
B
Backing Up Your Files, 3-7
battery
alarms, 4-7
changing, 4-8
charging, 2-6, 4-3
conserving power, 4-6
disposal, 4-9
LED, 1-3
monitoring power, 4-5
RTC
charging, 4-4
Bluetooth/Modem Module Cover,
1-9
brightness
adjusting, 2-11
buttons
Internet, 1-13, 3-8
TOSHIBA Console, 1-13, 3-8
TV Out, 1-13
Communications
setting up, 3-17
computer
caring, 3-20
lock, 3-16
registering, 2-13
turning off, 3-20
turning on, 2-9
Computing Tips, 3-2
Covers
Bluetooth/Modem Module, 1-9
Memory Module, 1-9
Wireless LAN Card Module, 1-9
Ctrl, Fn, and Alt keys, 3-3
D
DC-IN, 1-8
LED, 1-3
Digital Mode, 5-7
disk drive
problems, 7-7
display
problems, 7-6
display latch, 1-1
DVD
playing, 5-5
E
External Monitor
connecting, 6-4
port, 1-8
C
CD
inserting, 3-10
Mode, 5-6
playing, 3-10, 5-5
removing, 3-10
CD/Digital Mode Button, 1-1, 1-2
CD-ROM drive
problems, 7-9
Character keys, 3-3
F
FIR port, 1-6, 5-7
Function keys, 3-3
User's
Manual
User's Manual
1
Index-1
1 Last Saved on 30/05/2003 13:57
Index
H
Headphone Jack, 1-5
Hot swapping, 3-13
Hotkeys, 2-11, A-1
Mouse
connecting, 2-8
USB, 6-3
Multiple displays, 5-1
I
O
i.LINK port, 1-6
Internet button, 1-13, 3-8
Optical drives, 3-10
using, 3-9
Overlay keys, 3-4
K
Keyboard, 1-11
Caps Lock LED, 1-11
Character keys, 3-3
Ctrl, Fn, and Alt keys, 3-3
Cursor Lock LED, 1-11
Function keys, 3-3
Num Lock LED, 1-11
Overlay keys, 3-4
problems, 7-5
using, 3-3
using USB, 6-2
Windows® special keys, 3-4
L
LAN Jack, 1-7
LCD Screen, 1-10
Line-In
connecting, 6-7
Jack, 1-5
M
Main Hard Drive
LED, 1-4
memory, 6-9
installing additional, 6-9
problems, 7-3
Memory Module Cover, 1-9
Microphone
connecting, 6-7
Jack, 1-5
Mode
CD, 5-6
Digital, 5-7
modem
problems, 7-13
Modem
Jack, 1-6
Module
Lock, 1-9
Release Latches, 1-9
Module Bay
LED, 1-4
P
Parallel port, 1-8
PC Card
hot swapping, 3-13
inserting, 3-12
problems, 7-10
removing, 3-13
using, 3-11
PC Card Slots, 1-6
Peripherals, 6-1
Playing compact discs, 3-10
Ports
2nd Module Bay, 1-2
DC-IN, 1-8
External Monitor, 1-8
FIR, 1-6, 5-7
Headphone Jack, 1-5
i.LINK port, 1-6
LAN Jack, 1-7
Line-In Jack, 1-5
Main Module Bay, 1-2
Microphone Jack, 1-5
Modem Jack, 1-6
Parallel, 1-8
PC Card
Slots, 1-6
Remote Control Receiver, 1-1
SD Card Slot, 1-6
TV Out, 1-6
USB, 1-6, 1-8
Power
Button, 1-11
LED, 1-3
Power Management Utility,
5-10
problems, 7-4
Precautions, 3-1
Printer
connecting, 2-7
problems, 7-12
Printing, 3-7
User's Manual
Index-2
1 Last Saved on 30/05/2003 13:57
Index
Problems, 7-1
CD-ROM drive, 7-9
disk drive, 7-7
display, 7-6
keyboard, 7-5
memory, 7-3
modem, 7-13
PC Card, 7-10
power, 7-4
printer, 7-12
sound system, 7-9
Program
starting, 3-5
R
Remote Control, 5-8
Receiver, 1-1
Restoring the pre-installed
software, 3-21
S
Saving, 3-6
SD Card
inserting, 3-14
LED, 1-4
removing, 3-15
Slot, 1-6
using, 3-14
Security Lock Slot, 1-5
Setting Up Communications, 3-17
Setting Up Your Computer, 2-5
sound system
problems, 7-9
Starting A Program, 3-5
StickyKeys, 2-13, 3-8
System status indicators, 1-3
T
Television
connecting, 6-5
TOSHIBA Console button, 1-13,
3-8
TOSHIBA’s Online Resources, 3-21
Touch pad, 1-12
Control Buttons, 1-12
using, 2-10
TV Out
button, 1-13
port, 1-6
U
USB port, 1-6, 1-8
Using PC Cards, 3-11
Using SD Cards, 3-14
V
Volume Control, 1-5
W
Windows® special keys, 3-4
Wireless Communication
LED, 1-4
Switch, 1-5
Wireless LAN
using, 5-9
Wireless LAN Card Module Cover,
1-9
User's Manual
Index-3

Satellite P20 User`s Manual

Transcription

Similar documents

Mega Plexxus Instruction

Diagnostic Imaging Centre

CEFD JUN 05 SatMag 3 Quarter page.cdr

NAUTICO UTICO 3 NAUTICO UTICO 3

Satellite

Natomas Professional Center

Satellite L30

Re-tuning: TOSHIBA Freeview TVs

318CTB - RCS: Remote Control Solutions

LIFEPAK 500 Maintenance Checklist