310-3-1 Install Instructions

Installation Instructions
Folger Adam 310 Series Electric Strike
HES, Inc.
22630 N. 17th Ave.
Phoenix, AZ 85027
800-626-7590
www.hesinnovations.com
Product Components
1
2
300 Series Electric Strike Body & Faceplate
#12-24 x 1/2” Faceplate Mounting Screws
3
4
#12-24 x 3/8” Body Mounting Screws
Plug In Connector
1
2
3
4
Electrical Specifications
ELECTRICAL RATINGS FOR SOLENOID
CONTINUOUS DUTY
Resistance in Ohms
Amps
MINIMUM WIRE GAUGE REQUIREMENTS
12VDC
24VDC
23.5
.51
SOLENOID VOLTAGE
12VDC
24VDC
96
200 feet or less
.25
18 gauge
18 gauge
200 - 300 feet
16 gauge
18 gauge
300 - 400 feet
14 gauge
16 gauge
Solenoids are rated at +/- 10% indicated value.
1
Installation Directions
2
CAUTION! Before connecting any device at the installation site, verify input voltage using a multimeter.
Many power supplies and low voltage transformers operate at higher levels than listed. Any input voltage exceeding
10% of the solenoid rating may cause severe damage to the unit and will void the warranty.
Prepare Strike
Prepare Frame
1. Attach the faceplate to the strike body using the #12-24 x
3/8” Body Mounting screws as illustrated on page 3,
Diagram 2.
2. If using the LCBMA (Latchbolt & Locking Cam Monitor),
see Diagram 1 for wiring instructions.
3. The strike body ships as either a 12 or 24 volt
unit and is not field selectable. Verify the available
voltage is +/- 10% of the rated voltage of the strike body.
4. If using a mortise lockset, calculate offset using Diagram
3 on page 3.
5. Prepare frame using the template for your strike
located on pages 4-6.
Finish Installing
6. Connect the Plug In Connector to the electric strike, and
connect wires from the Plug In Connector leads to the
power source.
7. Install the electric strike unit in jamb cutout, using the
#12-24 x 1/2” faceplate mounting screws provided.
Latchbolt Monitor (LBM)
White
Orange
Green
Common
Normally Open
Normally Closed
White
Orange
Green
Locking Cam Monitor (LCM)
Brown
Blue
Yellow
Common
Normally Open
Normally Closed
Brown
Blue
Yellow
Installation Directions
3
Diagram 2: Faceplate Attachment
To install the 310 series electric strike body to the
faceplate, install two #12-24 body mounting screws
as shown. Make sure bolts are tightened and secured.
Keeper position can be adjusted by loosening the #12-24
body mounting screws, and repositioning the strike body
as needed. Retighten body mounting screws after
adjustment is made
Diagram 3: Determining Mortise Offset
4”
[101.60]
B
CL
Mortise
Door Prep
8”
[203.2]
CL
Strike
MORTISE LOCK
CORBIN/RUSSWIN
ARROW, FALCON
BEST 34H-37H
SARGENT (8200)
YALE (8800)
SCHLAGE
YALE (8700)
BEST 45H & 47H
B
0"
1/4"
3/16"
3 /4"
7/8"
1/8"
Cutout Templates
4
Inches [mm]
310-2 Template & Dimensions
1-3/8”
[35]
11/16”
[17.5]
5/16”
[7.9]
9"
[228.6]
8-3/8"
[212.7]
9”
[228.6]
3-3/4” 1-3/4”
[95.3] [44.5]
7-23/32”
[196.1]
8-3/8”
[212.7]
3-3/4"
[95.3]
2-5/8”
[66.7]
11/16”
[17.5]
11/16”
[17.5]
1-3/8”
[35]
5/32”
[3.9]
21/32”
[16.6]
1-1/2”
[38.4]
1/2”
[13]
1-5/8”
[41.3]
1-1/2"
[38.4]
310-2 3/4 Template & Dimensions
1-3/8”
[35]
11/16”
[17.5]
5/16”
[7.9]
9"
[228.6]
8-3/8"
[212.7]
3-3/4"
[95.3]
9”
[228.6]
3-3/4” 1-3/4”
[95.3] [44.5]
8-3/8”
[212.7]
2-5/8”
[66.7]
15/16”
[23.8]
7-1/8”
[180.9]
1-1/4”
[31.8]
5/32”
[3.9]
11/16”
[17.5]
3/4”
[19]
1-3/8”
[35]
2”
[50.8]
2"
[50.8]
Cutout Templates
5
Inches [mm]
310-2 3/4 OB Template & Dimensions
1-3/8”
[35]
11/16”
[17.5]
3-3/4"
[95.3]
5/16”
[7.9]
9"
[228.6]
8-3/8"
[212.7]
8-3/8”
[212.7]
9”
[228.6]
3-3/4” 1-3/4”
[95.3] [44.5]
7-1/8”
[181]
2-5/8”
[66.7]
1-1/4”
[31.7]
15/16”
[23.8]
2"
[50.8]
3/4”
[19]
11/16”
[17.5]
1-3/8”
[35]
5/32”
[3.9]
2”
[50.8]
310-2 3/4U Template & Dimensions
1-3/8”
[35]
11/16”
[17.5]
5/16”
[7.9]
9"
[228.6]
8-3/8"
[212.7]
3-3/4"
[95.3]
1/2”
[13]
8-3/8”
[212.7]
2-5/8”
[66.7]
15/16”
[23.8]
2"
[50.8]
9”
[228.6]
3-3/4” 1-3/4”
[95.3] [44.5]
11/16”
[17.5]
1-3/8”
[35]
7-1/8”
[181]
1-1/4”
[31.7]
5/32”
[3.9]
3/4”
[19]
2”
[50.8]
Cutout Templates
6
Inches [mm]
310-3-1 Template & Dimensions
1-3/8”
[35]
11/16”
[17.5]
9"
[228.6]
8-3/8"
[212.7]
2-3/8”
[60.33]
9”
[229.86]
3/4”
[19.16]
3-3/4”
[95.25]
8-3/8”
[212.7]
1-3/4”
[44.45]
3-3/4"
[95.3]
7-3/64”
[179.2]
*Deadlock
Block
2-1/4”
[57.15]
5/16”
[7.98]
1-1/4”
[31.75]
5/32”
[3.99]
11/16”
[17.6]
15/16”
2-1/2"
[63.5]
[23.94]
2-1/2”
[63.5]
1-3/8”
[34.93]
*The deadlock block that depresses the auxiliary latch can be rotated
180° to move the block 1/4” [6.4] higher if necessary. Handing of the
strike can be changed by moving the deadlock block and cavity plug
to the opposite cavities in the face plate.
3810006.001 rev B.
© 2010 HES, Inc.