TV channel guide

User manual
Digital satellite receiver
Reference: 441550
5000 Channels / Parental Control
2 Scarts / DiSEqC 1.2 /
Digital PVR
MET519
CAUTION
The interior of your receiver (Re)playBox contains some components that are
under high tension, never open the appliance, even after unplugging the power supply.
In general, electrical appliances are not connected to earth, you can then get some
electrical discharges (which are not risky) when you touch 2 appliances at the same time
(or an appliance and an aerial cable). Our advice is to connect the equipment after all the
sockets connections have been made.
To clean the receiver or its remote control, do not use any solvent or detergent. A
dry clothe or slightly dampened with water will be perfect to take off the dust.
Do not install the receiver near other appliances. Choose an aerated place and
never put anything on his ventilation slots. The receiver must not be exposed to dripping
or splashing, and no object filled with liquid, such as vases, shall be put on the appliance.
Never put the appliance on the top of another appliance, the overheating could cause
a premature ageing of the components. In case of a storm, disconnect all your audiovideo appliances from the main supply: they could have damaged not covered by the
guarantee.
The remote control needs 2 AA 1,5V batteries. Check the polarity before fitting
them into the remote control. In the respect of environment and law, do not throw your
used batteries in the bin. Take them to your local store where special boxes are provided
to recycle the used one.
The installation and the use of the receiver are based on pre-programmed
channels. In case of a problem on one channel, get a specialized magazine to find out
if this channel is still broadcasting in Free To Air. For your information, the operators
frequently change the channel’s characteristic without prior notice.
Your (Re)playBOX receiver is compatible with DiSEqC 1.2, it could then direct
all the DiSEqC 1.2 motor. In case of a DiSEqC 1.2 motorised installation, we advise you
to install the motor in an easily accessible location (avoid chimney for example). Motors
may have to be screwed up or lubricated… An installation in a not very accessible place
would be difficult to maintain. For your information the DiSEqC standard is a registered
trademark by Eutelsat.
If you have only one satellite receiver, you will not be able to record a different
satellite channel from the one your are watching. We then advise you to keep your
terrestrial aerial if you got one.
1
Sommaire
1 - General installation advice......................................................................page
2 - Installation of a fixed dish on a satellite.................................................. page
3 - Installation of a dual-headsatellite dish Astra 19,2° + Hotbird................. page
4 - Installation of a motorised installation.....................................................page
5 - Connection with a fixed dish already aligned on a satellite......................page
6 - Connection on a motorised DiSEqC 1.2 unit already aligned.................. page
7 - Remote ontrol description.......................................................................page
8 - (Re)playBOX receiver description.......................................................... page
9 - Day to Day use...................................................................................... page
10 - Add channels........................................................................................ page
11 - Personalize channel list...........................................................................page
12 - Advanced options...................................................................................page
13 - Radios.................................................................................................... page
14 - Electrical stops adjustment.....................................................................page
15 - Mechanical stops adjustment................................................................. page
16 - Use with a VCR...................................................................................... page
17 - Universal remote control........................................................................ page
18 - Digital PVR............................................................................................ page
19 - Digital services...................................................................................... page
20 - Common interface (CI)......................................................................... page
21 - Questions and answers...........................................................................page
22 - Certificate of guarantee.......................................................................... page
23 - Questionnaire......................................................................................... page
Channel guide................................................................................................page
3
6
7
9
19
19
20
21
21
22
24
26
28
28
28
30
30
31
34
35
36
37
39
41
Installation shortcut
Your dish is already aligned
page 19
You buy the receiver + the dish
Installation advice page 3
Fixed single head
dish
Fixed twin dish
Motorised dish
Page 6
Page 7
Page 9
2
1
General installation advice
A
Choice of the location and satellite dish assembling
Whatever your choice of installation, your fixing must be stable and vertical.
• In the event of an obstacle, respect the rule of distances explained below. For example,
a building with a height of 10m will not interfere with the reception as soon as it is
situated at more than 15m from the satellite dish. For a motorised installation, only a
patio stand or a wall stand off arm is suitable.
• For the satellite assembly, look at the assembly sheet provided with the satellite dish
screwing kit.
CAUTION : Please handle the satellite dish with caution because its fringes might be
sharp.
3
B
Necessary parts and tools:
11
13
10
12
1
2
3
4
5
Satellite dish
Screws and fixing
Offset arm
Universal LNB
Pole or wall mounting with a minimum
diameter of 40mm
6 - Digital satellite receiver with remote
control
7 - TV
8 - Scart Lead
9 - «F» plug
10 - Satellite cable, the standard TV cables is
not appropriate.
1,5V
AAA
-
1
4
9
Mute
2
3
1
2
4
6
8
9
0
Back
i
Last
Timer
EPG
TTX.
Subt.
Menu
List
+
5
OK
3
=
10
5
TS
4
6
List
7
Del
4
8
<
;
9
6
C
7
3
5
7
Extra
Audio
8
Assembly and insulation of the «F» plug
• The plug must be screwed on the aluminium strip iron. Take care that there is not a
strand of the braid in contact with the central heart of the coaxial cable. If you screw
the F plug very easily, the cable may disconnect itself. Do not worry if the screwing is a
bit hard, that means that the F plug is adapted to the cable.
• When your installation is finished, do not forget to protect the LNB connexion with
appropriate waterproof materials, isolation paste, or in defect silicone (see picture
below).
LNBs badly insulated or not insulated at all are not covered by the guarantee.
5 mm 8 mm
4
D
LNBs assembly
Your satellite kit can contain various type of LNB
• LNB in metal grey (schema D1): make sure to position the triangular mark (5) upwards.
It is normal that the body of the head is tilted on 45°, the cable leaves tilted at 45°.
• Other LNBs (graduations): must be positioned vertically. See schema D2 (the cable leaves
vertically).
In both cases, never remove the horn protection cap.
D1
E
D2
Pre-programmed channels and satellites
Your (Re)playBOX receiver is delivered pre-programmed on the main satellites available
in Europe. Some satellites require a one meter satellite dish, you will not be able to
receive them with a lower size satellite dish, even if this satellite appears in your preprogrammed channel list. You will use these channels to point your satellite dish towards
the satellite you want. The table 1 gives you the satellite dish necessary size, in the United
Kingdom and the Republic of Ireland, for each satellite, as well as the reference channel,
which will be useful to align your dish with the satellites.
Table 1:
Reference
channel
Importante notes:
• Table 1 does not mention the satellites, which do not broadcast (or very little) in Digital Free To Air.
• The reference channel were validated at the time of drafting of this user manual, we cannot guarantee that
they will still be there. In the event of a problem at the time of searching a satellite, get a specialized magazine to check if the reference channel is still a Free To Air channel (like What Satellite and Digital TV). Use,
if possible a channel with the highest debit (SR) as possible. For example for Hotbird, 76 could replace 72
as a reference channel.
• For the alignment, you must imperatively know which satellite you wish to receive. If you have any doubt
check the pre-programmed channels at the end of this user manual.
5
2
Installation of a fixed dish on a satellite
Read the installation advice, and particulary the paragraph E (page 5).
A
B
Connections
The receiver must be disconnected from the power supply, connect directly the LNB to the
receiver LNB input. Connect the television to the receiver scart socket output. Switch on
the television and connect the receiver to the power supply. A point appears on the Receiver display. Press on the
key. The starting sequence appears on the receiver display,
which is: display of “ON” then switch off, then “ON” appears again, then “SCAN”, then
“ON” then finally 0001. If the television does not display a black screen with a message “
No signal “, checks the scart leads connections and/or force the A/V or EXT mode of your
television (see your TV user manual).
Alignment / Satellite dish orientation
• Find in Table 1 (page 5) the satellite reference channel number that you wish to receive (example: 072 = ZDF if you would like to receive HotBird). Type on the remote control the channel number.
• The screen stays black or you can read no signal. Press on the remote control the
INFO key (i) to show the reception gauge level at the bottom of the screen (see pictures underneath). The blue line show the level of signal, and the red line show the
level of quality. On the example underneath, the signal is not enough on the left (black
screen, quality line zero) and the signal is correct on the right (ZDF image on the
screen and quality almost at its maximum).
• Put the satellite dish vertically (the graduations on the back indicate 20-25°) and
roughly direct it towards the south. Make a slow sweeping (about 20 seconds) of a
quarter of spin on the left then a quarter of spin on the right while checking on the
television. The indicator should not show anything at this stage.
• Incline the satellite dish for 2 degrees (about 2cm on the top of the satellite dish)
towards the top and then start again the sweeping.
• Proceed by 2 degrees step until the indicator goes up and that the channel appears.
When the channel appears, adjust the alignment (vertically and horizontally) to get
the maximum of signal. Tighten all the screws definitively, except those, which fix
the LNB in its support.
Note: The size of the level indicator does not really matter. What does matter is the variation when
you move the satellite dish. When the signal is going up a bit, stop the sweeping to see if
the quality line increase.
6
C
Adjustment of counter polarization
Spin the LNB clockwise in its support for a few degrees to further increase the level of
signal. If the signal decreases, spin it in the other way.
Once you obtain the best signal, tighten definitively the screws from the LNB. You can
now watch all the satellite channels from the satellite you just aligned your satellite dish
on.
3
Installation of a bi-head satellite dish Astra 19,2 + Hotbird
The easiest way of receiving Astra and Hotbird satellite is to install a LNB called
“Monobloc” on an 80cm satellite dish. A LNB Monobloc contain a DiSEqC 1.0 switch
that you have to declare before aligning the satellite dish.
A
Switch declaration
• Press on the MENU key
• Press on OK to validate the menu system
• On the DiSEqC line, press on 4 to show 1.0
• Press on the key [Back] to come back in the main menu
• Go down on Channel search and then press OK
• Go down on manual search and then press OK
• On the row satellite, select ASTRA with the keys 34
• Go down on the DiSEqC row and select 2 with the keys 34
• Go back on the satellite row and select HOTBIRD with the keys 34
• Go down on the DiSEqC row and select 1 with the keys 34
• Leave all the menus by pressing on the key [Exit]
7
B
Installation / Alignment
• Install the Monobloc like you see on the schema underneath.
• Do the alignment on Hotbird like indicated in the preceding paragraph (fixed dish on a
satellite)
• When you receive Hotbird, you should automatically receive the Astra channels. Sometimes, it is necessary to adjust the alignment to optimise the reception of the 2 satellites.
Caution: Some monoblocs have an inversed command. It can be then necessary to inverse
1 and 2 in the DiSEqC line.
You can then watch the Free To Air pre-programmed channels on Astra 19.2 and Hotbird
(from 64 to 409)
Rougly 10°
8
4
A
Installation of a motorized unit
Foreword
This user manual will explain to you how to install a motorised installation with a motor ref:
450908. If you have another motor, please see in its user manual. The motor user manual contains as well an installation procedure for your (Re)playBOX receiver. We advise you to follow this
one, which have been updated more recently. In any case you will have to do all these operations:
0 - Switch on the receiver
Connect the receiver to the power supply, a point appears, press on the ( ) remote control key.
The point disappears, then «ON»appears, and then, after a few seconds, the number of the last
channel watches appears (0001 from output of factory). On the television, the screen indicates
«no signal».
1 - Put the receiver on the reference satellite channel
Check into the table 1 page 5 what is the reference satellite channel. Tape the 4 numbers of its
figure on the remote control. For ex: 0072 for Hotbird.
2 - Go into the DiSEqC 1.2 menu
• Press on Menu, go down onto motor adjustment and then validate by OK.
• If the menu is not accessible (in grey), it means that the DiSEqC version (in the menu system)
is on 1.0 instead of 1.2.
3 - Reset the motor
In the menu motor adjustment
• Select place the limit and validate by OK
• Go down on the reference position row and tape OK. The motor is going to its reference
position (mechanical stop East on the Metronic motor, ref: 450908).
4 - Continuing rotation
In the menu motor adjustment, go onto the row movement E/O. A press on the 4 key
spin the motor towards the west. A second press stop the motor. Use the same way the 3
key to spin towards the East.
Note: The size of the level indicator does not have a real importance as such. What is important it is the
variation when you move the dish. When the level is going up a bit, stop the spinning to check if the
quality level has increased.
5 - Step by step rotation
In the menu motor adjustment, go onto the row adjust E/O. A press on the 4 key make
the motor spin a step towards the west. A press on the 3 key make the motor spin a step
towards the East.
6 - Give a number to a satellite
In the menu motor adjustment, go onto the row satellite number. With the key 34choose the
number you want. Press on OK and then confirm by pressing again on OK. Wait that the motor
stops.
7 - Memorise a satellite position
In the menu motor adjustment, go onto the menu Movement E/O, press on OK. The key
OK switches off briefly on the screen.
8 - Display the signal indicator
Press on the INFO (i) key. The indicator appears as 2 lines. For the alignment, you need to maximise the level (bottom line) then, when it is going up, optimise the quality (top line). If the level
is too high, but the quality is not going up, that means you are on another satellite, you need to
carry on sweeping.
9
B
Necessary elements
1 - Satellite dish
2 - Screws and fixing
3 - Offset arms
4 - Universal LNB
5 - Mast or stand off arm
Recommended Ø minimum 40mm (1,6ʼʼ)
6 - (Re)playBOX
7 - TV Pal for digital reception and Pal /
Secam for analogue (to be able to watch
it in colour)
8 - Scart Lead male/male 21 pin
9 - «F» plug
10 - Cable special for satellite (normal TV
cable won’t work)
11- Motor 450908
11
13
18
10
12
17
1,5V
AAA
1
1
2
4
11
3
7
5
10
8
6
9
10
C
Assembing the motor (See schema 2)
• Make sure the fixing (tube or stand off arm) is stabilised and strictly vertical. A gap
of more than 1 degree (2cm, 0,78” per meter) from the vertical will prevent the
motor to work correctly. In case, add some block between the wall and the fixing.
Check the verticality with a spirit level or a plumb line.
Warning: When you will screw the screw 2C (which must not be blocked), a too
important tightening might break one of the support clamps.
When the motor is assemble, do not fix it straight away on the mast or the stand off
arm, some operations needs to be done near the receiver.
• Screw on all the screw without blocking it. The screw 2b must be tighten at the
maximum and the cover 2a must be leave up to allow you to read the motor azimuth (angle in relation to south)
Warning: the screw 2b must get in by the small hole in the bend mast and the nut
must be tighten on the big hole side, with the rounded nut moulded the curves of the
big hole.
• Adjust the motor elevation (read near 2d) on around 35°.
2
��
��
��
��
��
��
��
��
��
��
11
D
Connection
For the installation you will need 2 pieces of cable. The first one, roughly 1,5m
(4,92ft) to go from the LNB to the motor,
the second one as long as it takes to go
from the motor to the receiver.
����
����
Prepare the cables and assemble the “F”
plug at the end of the cable.
Respect the dimension indicated on the
schema above; the plug must screw on
the aluminium foil roll up. Make sure that
none of the braid strand is in contact with
the central core of the cable.
Motor Horizon-Horizon
Ref. 450908
Connect the receiver to the television
with a scart lead. Put the motor near
the receiver, on a table or on the floor,
and connect the receiver LNB input to
the Motor DEMO output with the 1,5m
(4,92ft) cable, then switch on the receiver(0).
E
S/N 3mm441550nnnnnn
Motor
(Re)playBOX
Reset the motor and checking of the stops
The reset of the motor is to reinitialise its position, and not to put him at 0°, which
means face south.
Go into the DiSEqC 1.2(2) menu and then reset the motor(3) (see pictures on the
opposite)
• The motor will reinitialise while looking for is reference position (Mechanic
east stop). The motor should stop at 45°
(at the nearest 10°). If it is not the case,
check the mechanical stop as indicated at
the end of this user manual. If the motor
does not spin, connect the motor to the
LNB with the long cable then reset the
motor.
To verify the right position of the mechanic west stop, do a continuous spinning(4)
towards the west. The motor should stop
at 45° (to within about 10°). If it is not the
case, check the mechanical stop (see inside the motor user manual).
12
(0)(2)(3)(4)
See the paragraphs on the
page 9.
Prepare the motor
You will now memorised the Hot Bird position then take back the motor precisely at 0° to
assemble the satellite dish.
1) Put the receiver on the Hotbird reference
channel (1), while typing 0072 on the remote
control.
2) Give a number to the Hotbird satellite(6) (in any
doubt put 4), and then wait that the motor stops
spinning.
3) Look into the schema underneath the Hotbird
position (the azimuth) in your region. Ex:
Finistere (29) = 22° East. If you install your
motor outside France, check on the map F1
(ex: Madrid = 25°E).
East Hotbird azimuths:
left from the south
Azimut
Département
Azimut
Département
Azimut
Département
Azimut
Département
Azimut
F1
Département
F
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
��
��
��
��
��
�
��
��
��
��
��
��
��
��
��
��
��
��
��
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
�
��
��
��
��
�
��
��
��
��
��
��
��
��
��
��
��
��
��
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
�
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
��
��
��
��
��
��
��
��
��
�
�
��
�
��
��
�
��
��
��
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
��
��
��
��
��
��
��
��
��
��
��
�
��
�
��
��
��
��
��
�������������������
���������������
��������������������
�����
��
��
��
��
Table 2 :
azimuths of Hot Bird
4) Go into the DiSEqC 1.2(2) menu then, with a
continuing rotation(4), bring the motor roughly on
the Hotbird azimuth in your region. Then bring the
motor precisely to this azimuth with a step by step
rotation(5).
Example: Department 29 – Azimuth 22:
The person using the remote control must make the
motor spin until you reach the metallic notch used
to read the azimuth at 22°. When we look at the
graduations, the notch should go to 22° towards the
right (in our example) so the satellite dish will be
directed toward the left, so the East.
(1)(2)(4)(5)(6)
13
See the paragraphs on the
page 9.
5) Memorised the Hotbird position (7)
6) With the Continuing rotation
precisely at the 0° position.
(4)
then a step by step rotation
(5)
, bring the motor
7) Switch off the receiver, take off the cables and then fix the motor on the top end of the
support.
8) Direct approximately the motor towards the south. In case of an assembling on a wall,
make sure the wall faces south (to within about 20°) and use a 45cm stand off arm at
least (ref: 450359): see schema F2.
9) Connect the receiver and the motor by the long wire prepared at the step D.
F2
G
Satellite dish assembling
Assemble the different elements from the satellite dish in checking the user manual includes with it.
• For the METRONIC satellite dish in metal 77-80cm (Four holes), the satellite dish back
support should be adjusted at 54° (check the picture above).
• For the 85cm Transparent Metronic satellite dish, adjusted the elevation at the
maximum (45°)
• For another satellite dish, try 48°, but you might have to try some other value if you
have any problem with the alignment.
14
(4)(5)(7)
See the paragraphs on the
page 9.
H
Assembling the satellite dish on the motor
• Assemble the satellite dish and fix it on the motor’s mast. The satellite dish U-Bolt
must be the highest as possible on the angled arm to avoid the bottom of the dish to
touch the motor. As the motor is at 0°, make sure you perfectly align the dish offset
arm with the motor (schema H1).
• Direct approximately the whole (satellite dish + rotor) towards the south. At this level,
it is not necessary to tighten the nuts too much. Tighten up the lock nut 12a to the
maximum (see schema 12). Tighten the elevation nut 12b to bring the satellite dish
in vertical position. Check again that the satellite dish elevation is at 54° (graduation
12c) and that the satellite is vertical whatever the way (lateral and incline).
• Switch on the receiver, put it on the Hotbird reference channel while pressing 0072 on
the remote control.
• Do a continuing rotation (4) until the stop 45° East and 45° West to check if there is no
obstacle. If you get close from an obstacle during the spin, go back to paragraph 15
page 28 to adjust your mechanical stop.
H1
12
S
N
����������
����
12a
12b
I
Assembling the LNB head (See § D page 5)
(4)
See the paragraphs on the
page 9.
15
12c
J
Checking
Before going to the final stage (the alignment) check that your installation looks like the
picture below.
11
K
Aligment / Satellite dish orientation
• At the end of the step K, you will receive the reference channel ZDF on the television
screen. Do not go to step L (adjusting the alignment) if you do not receive it or if you
receive another channel.
1) Put the receiver on the Hotbird reference channel 0072 then display the signal indicator (8).
2) Launch a slow scan (for 20 seconds) a quarter of the way on the right, then a
quarter of the way on the left while pivoting manually the whole (satellite dish +
rotor) around the mast, while checking the level. If the level is not going up, screw
the nut 12b 1 round to increase the satellite dish incline and do the same manual
scan. Carry on as above by step of 1screw round followed by a scan until the level
increase. When you are on the right satellite, the image will appear in the background. Adjust it to obtain the maximum in level and quality (bar the longest as
possible). In some area, it is normal that you will turn up to 20 times your nut, be
patient.
3) Block temporally all the nuts. Warning: the Tighten of the nut is enough to debase
the picture. Block the elevation by tightening the lock nut 12a.
Warning: a too important tightening of the U-bolt 2e (schema 2 page 11), may break one
of the fixing clamp.
16
(8)
See the paragraphs on the page 9.
Orientation adjustment
• Put the receiver on the Atlantic Bird 3 reference (1) channel.
• Check in diagram the Atlantic Bird 3 angular reading of your geographical area.
• Give (6) a satellite number to Atlantic Bird 3 (put 01 in case you hesitate).
Département
Azimut
Département
Azimut
Département
Azimut
Département
Azimut
��
��
��
��
��
�
��
��
��
��
���
���
���
���
���
���
���
���
���
���
��
��
��
��
��
��
��
��
��
��
���
���
���
���
���
���
���
���
���
���
��
��
��
��
��
��
��
��
��
��
���
���
���
���
���
���
���
���
���
���
��
��
��
��
��
��
��
��
��
��
���
���
���
���
���
���
���
���
���
���
��
��
��
��
��
��
��
��
��
��
���
���
���
���
���
���
���
���
���
���
��
��
��
��
��
��
��
��
��
��
���
���
���
���
���
���
���
���
���
���
��
��
��
��
��
��
��
��
��
��
Azimut
Azimut
���
���
���
���
���
���
���
���
���
���
Département
Département
��
��
��
��
��
��
��
��
��
��
Azimut
���
���
���
���
���
���
���
���
���
���
Département
��
��
��
��
��
��
��
����
��
��
Département
Azimut
���
���
���
���
���
���
���
���
���
���
Azimut
Département
Atlantic Azimuts
Bird 3 de
Atlantic Bird 3
west azimuth:
right :
OUEST
fromà the
south
droite
du SUD
Azimut
16
Département
L
���
���
���
���
���
��
��
��
��
��
Table 3 : azimuths of Atlantic Bird 3.
• If the motor does not stop at the right value, bring it with a continuing research (4) or
step by step (5).
• Memorised (7) this position for Atlantic Bird 3.
Leave all the menus and check that you correctly receive the Atlantic Bird 3 reference
channel (3). If it is not the case, you have 2 cases:
Primary case: You do not receive anything at all, even when you slightly move the satellite dish alignment. In that case, it means that an error has been made during the installation (mast not vertical, error between east and West, bad reading of the azimuth…).
Restart the installation from the beginning while checking the details very carefully.
Secondary case: You have a bad reception and you have to adjust slightly the satellite
dish position angle (1 or 2 degrees) to receive correctly Atlantic Bird 3. In that case, the
design curve of the motor is out of line with the real curve. We then advise you to go
back to the step K while putting 2° more for the Hotbird position in your area (ex 24° E).
If the result is not good, try 2° less.
(1)(4)(5)(6)(7)
page 9.
See the paragraphs on the
17
M
Satellite validation
For each satellite, you have now to memorise the right position in the motor. The
operation is done for Hotbird and Atlantic Bird 3, you have to do it for Astra, etc.
Example for Astra 19°E
• Go onto the Astra reference channel (301 = TV5).
• Go into the DiSEqC 1.2
hesitate).
(2)
menu and give a number
(6)
• By a continuing rotation (4) and then a step by step rotation
obtain the maximum level and quality.
to Astra 19°E (03 if you
(5)
, make the motor spin to
• Memorised (7) the position founded.
• Check that you receive the Astra channel. If it is not the case, that means that you
memorised another satellite, which emit some channels at the same frequency. Try the
operation above again and make sure that your satellite dish is pointed slightly on the
left from Hotbird like shown on the Diagram 17 underneath. Do the same operations
for the other satellites. For your information, the diagram 17, gives you the satellites
relative position for which some channels are pre-programmed in the metronic
receivers. When you receive all the satellites, screw definitively all the nuts. Your
installation is finished.
Note: The Hispasat reception with a motorised installation is very difficult and need
a perfect alignment. For the perfect reception of this satellite, we advise a fixed
installation, with a particular look at the adjusting of the counter-polarization.
Turksat
Reminder: 17
Atlantic Bird 3 =
ex Telecom 2C
N
«F» plug isolation
When your installation is finished, do not forget to protect the LNB connexion with
appropriate waterproof materials, isolation paste, or in defect, silicone (see picture § C
page 4).
18
(2)(4)(5)(6)(7)
See the paragraphs on the page
9.
5
Connection with a fixed satellite dish already aligned on a satellite
Notes: if your satellite dish is currently pointed towards Atlantic Bird 3 (ex Telecom
2C = national analogue channel in Free To Air), you will not have access to any digital channels. We then advise you to install another satellite dish to keep receiving the
national channels in analogue and watch others channels in digital.
The receiver being disconnected from power supply, connect directly the LNB to the
LNB receiver input. Connect a scart lead from the television to the receiver TV output scart socket. Switch the television, connect the receiver to the power supply, the
television indicate “no signal”. Press onto the OK key, the pre-programmed channel
list appears. Look into the table 1 (page 4) to know which satellite number , your dish
is currently pointed to (example Astra 19.2 = 3). You can select and watch the channel
from this satellite (from 291 to 409 in our example).
6
Connection on a motorised DiSEqC 1.2 unit already aligned
If you have a DiSEqC 1.2 motorised installation already installed, each satellite position
is already correctly programmed in your motor. For the motor, a satellite is recognised by
numeration. The user manual from your old receiver should indicate you the numbers used.
If it is the case your (Re)playBOX installation will be very easy. If you do not have access to
this numeration, use the one proposed in the table 1 page 4.
• Connect the cables and the leads as indicated on the figure 18 below.
(6)
• For each satellite, go onto the reference channel then give the right satellite number.
The motor should go automatically to the right position, which appears as an important
quality line (see pictures underneath on the right).
18
S/N 3mm441550nnnnnn
Satellite cable
Scart cable
(6)
19
See the paragraphs on the page 9.
7
Remote control description
1
Digital keys. In normal use, it allows to type the channel
number desired. In the programming mode, it allows you to
enter the digital values.
2
Touch ON / OFF. Allows switching on or switching off and
putting the terminal in standby.
3
MENU Key. Allow you to enter in the main menu.
4
In the menu allow you to modify different parameters.
5
6CH5 Keys. In normal use, a press on one of the keys
change channel. In the menus, allow you to pass from one
row to another.
6
Timer Key. Allow you to enter the menu for the adjustment
of the later time recording programs.
7
Unused on this model.
8
EPG Key (Electronic Program Guide). Show the program in
progress and the following ones, when the channels transmit
this information.
9
Audio Key. When several audio ways are transmitted (Euronews on Hot Bird for example) it makes it possible to choose the language of the broadcast.
10
Key back, to go back of a screen in the menus.
11
MUTE Key. A first press makes it possible to switch off the
sound. A second press returns in normal mode.
12
13
OK Key. Allow you to validate a choice when you are in the
menus. In normal mode (watching a channel), display the
channel list.
PAGE Key. Allow you to switch from one page to another in
the long list.
TV/RADIO Key to switch from TV mode to RADIO and
opposite.
FAV Key. To access your favourite channels.
14
Allows you to go back to the last channel watched.
15
EXIT Key. Allows you to leave the menus and going back in
the watching mode.
16
INFO Key, Several press display some information on the
channel in progress ( Name, actual broadcast, next broadcast, technical parameters).
17
Key to adjust the volume.
DIGITAL PVR
18
To erase a recording on the list.
19
Classic functions keys on a VCR (see § 18)
20
To show the recording list.
20
2
1
7
6
3
11
Mute
1
2
3
4
5
6
7
8
9
Extra
0
13
9
Audio
8
EPG
TTX.
Subt.
10
Back
Menu
Exit
Last
16
i
+
17
4
20
Timer
7
15
5
Del
5
19
TS
12
4
OK
List
14
18
8
Description of the receiver (Re)playBOX
31
32
30 29 30
27
28
23
24
21
33
S/N 3mm441550nnnnnn
25
21222324252627282930313233-
9
22
26
LNB input to connect the satellite cable.
VCR scart input. When you read a cassette, the VCR will automatically take over
the receiver. You can use this scart input to connect an analogue receiver.
TV scart output. To connect the receiver to the television.
Digital audio output (AC3).
RCA female output left and right.
RS232 connector, After sales service only.
Power supply.
Sleep mode switch. In position OFF, the consumption is equal to zero.
ON / OFF key
key 65the same as on the remote control
remote control receiver
Display. In normal functioning, it will display the channel number in progress.
Output to supply another receiver.
Day to day use
In normal use, you will use only the following keys whose function is described in the
preceding paragraph:
• + - Keys to regulate the sound volume.
• 65Keys to change channels
• MUTE Key to switch off and switch on the sound.
• Digital Keys or OK key to go directly to a channel
• RADIO key to listen to the radios in digital quality. We advise you to connect your
(Re)playBOX to your Hi-Fi system with a 2 RCA male / 2 RCA male flylead.
• EPG Key to reach the programs guide.
• Digital PVR key to record and read your recording.
21
10
Add channels
You can add a particular channel, from which you know the technical characteristics, or
add some new unknown channel (update).
A
Add a particular channel
A channel is emitted by what is called a transponder. It is a relay satellite from which you
should known the 4 following parameters:
• Its frequency (e.g. 12551 MHz).
• Its debit of symbol SR (e.g. 22000)
• Its polarity (e.g. Vertical)
• The satellite which emits it (e.g. Astra 19.2).
You will find these parameters in specialized magazines, which propose a monthly update,
or on www.lyngsat.com, www.telesatellite.com ou www.satcodx.com.
To add a channel go into the main menu / channel search / manual search
• On the Satellite row, select the satellite with 34 keys.
• As your LNB installation’s parameters are already adjusted, leave the numbers indicated
on the row 2 to 5.
• On the row polarization, choose horizontal or vertical.
• Go onto the row follow and then press on OK to access the second page.
• On the row frequency, enter the 5 figures of the satellite frequency.
• On the row SR, enter the 5 figures of its debit symbol (SR). At this stage, if the quality
line has not gone up, that means that the numbers are false or out of date. Check back
into the magazines or websites.
• On the row research network, leave deactivated.
• On the row programs type, choose all with the 34 keys. The option FTA (Free To Air)
allows you to enter in memory the Free channels. The crypted option allows you to put in
memory only the pay per view channels.
• Go onto the row start the research and type OK.
The research start and the channel list found appears.
On the page that display the channel found,
the quality line is at the bottom, and the blue
line at the top show you the progression. When
the line is totally blue, that means that the
research is finished. If no channel appears, and
the reception quality is good, that means that
the channels are already in memory.
22
B
Satellite update
•
•
•
•
Go into Menu / Search channels / automatic search
With the arrows 56, select the satellite you want to update.
Press on OK, a selection sign appears near the name.
Press on the red key (audio) to launch the automatic update.
At this stage, if the quality is under 30, that means the parameters are false.
• On the row FEC, leave automatic
• On the row type search, choose FTA (channel in clear only)
• On the row network search, choose start
• Press on OK to launch the research. A window shows you the number of TV channel and
radios have been found.
• Press on EXIT when the search is finished.
On the page which display the channel found, the quality line is at the bottom, and the
blue line at the top show you the progression. When the line is totally blue, that means
that the research is finished. If no channel appears, and the reception quality is good, that
means that the channels are already in memory.
Note: before launching the search, you can select several satellites. In that case, as
soon as the search on the first satellite is finished, the search on the second satellite
starts and so on. This method should not be used on a motorised installation.
23
11
Personalize the channel list
You have 2 possibilities to personalize the channel list. The first one is to create some
favourite channels. The second one is to erase, move or rename the existing channels.
A
Favorites channels
Select channels
- Go into Menu / channel list
- On the row edit the favourite list, select a
list with the arrow 34 and validate by OK.
- In the favourite selection window (see pictures opposite), select the channel you want
to add to the list and then validate by OK.
To take off a channel from a favourite list, you
have to press on the green key to bring the
cursor in the left list, then press OK on the
channel to erase.
Rename a list
•
•
•
•
•
Go into Menu / channel list / rename a list
Change the first letter with the arrows 56
Go to the next letter with the key4
Modify the 2nd letter the same way, then the 3rd one etc.
Press on OK to quit and save.
Watch the favourite channels
When you press on OK to make appears the channel list, the list that is displayed by
default is the total one. You just have to press on the green key (Timer) to go from a
list to another.
When you have selected a channel from a favourite list, the arrows 56 allow you to go
to the next or preceding channel from the list in progress.
To go back to a complete display, tape OK to display the channel list then several
times on timer until the total list appears again.
24
B
Modify the channel list
Erase some channels
• Go into Menu / channel list / erase channel
• Press OK on each channel to erase, a box ticked appears on the side of the name.
• Press on 4 to move your selection in the list to erase
• You can still select some other channels with OK then 4 (maximum 100)
• Press on Exit when your selection is finished
• Confirm by OK to erase the channels
Move some channels
• Go into Menu / channel list
• Go onto Move a channel and select the list to modify with the arrows 34then validate by OK.
• In the window Move a channel, tape OK on the channel you want to move. The headband becomes blue.
• Move the channel where you want with the arrows, then validate the new position by
OK.
Rename a channel
• Go into Menu / channel list
• Go onto rename a channel and select a list with the arrows 34 then validate by OK.
Note: the choice of the list at this stage allows you simply to be easier to research a
channel. If you modify the channel name, the new name is used for all the list.
•
•
•
•
•
•
In the window, rename a channel, tape OK on the channel you want to rename.
Change the first letter with the arrows 56
Go to the next letter with the 4 key
Modify the second letter the same way, then the third one etc.
Press on OK to save the new name.
Press on exit to quit and save.
25
12
A
Advanced options
Parental control
Your (Re)playBOX receiver is delivered with a secret code (PIN), which is 0000. This
secret PIN allows you to block restraint the channel access or protect your receiver configuration. We advise you to change it.
Modify the password
•
•
•
•
•
•
Go into Menu / Parental Control
Enter the 4 digits passwords (0000 from factory output)
Select modify password (PIN) and validate by OK.
Enter the 4 digits from the new password (PIN)
Enter again this 4 digits to avoid a mistake
Tape Exit to leave and save.
Take a note about the password (for example on your receipt).
Block some channels
• Go into Menu / Parental Control
• Enter the 4 digits of the password (0000 from factory output)
• Go onto channel to Block and select the list to modify with the arrow 34then validate
by OK.
Note: the choice of the list at this stage allows you simply to be easier to research a
channel. If you block a channel in a list, this channel will be blocked in all the list.
• Tape OK on each channel you want to block, a padlock appears after the channel name.
• Tape Exit to leave and Save.
26
B
Reset the receiver
The resetting of the receiver to the manufacturing specification could be useful if you
modify the programming of your receiver at that some of the functions are not working
anymore. When you reset your receiver, the configuration will be like when the product is
new. All your personalisation (favourite channels, radios, etc) will be lost. The reset will
not modify the hard drive contain.
• Go into Menu / factory reset
• After entering your password (0000 from output of factory), you to confirm your choice
by pressing OK.
• After a few seconds, the window from the first start appears.
• Select the language (English or French, etc.) by pressing on 6 then validate by OK.
• The welcome screen shows you the way to follow. Press on OK.
• After adjusting the general configuration in the menu SYSTEM (see § 12 C underneath),
you have the choice between:
• The key Exit to restore the factory channel list (you have to wait a few
seconds)
• The key Menu to personalize your channel search
If you use the key Menu, you will not be able to leave the menus before you add a channel. Use this option only if you know perfectly your installation and that you feel confident
to search the channels.
C
Menu SYSTEM
The menu SYSTEM put together some different options:
• The row Time difference allows you to adjust the difference between the time and the
Greenwich Meridien timing (GMT). For your information, in France, the time is GMT+1,
in the UK it is GMT. If you use the appliance in a country which is not listed (Belgium,
for example) choose a country whish is at the same time (France for example).
• The row Summer Time allows you to take in consideration the summer time difference.
Put on activate the last weekend of March and on deactivate the last weekend of October.
• On the row screen format, choose 4:3 or 16:9 depending on the size of your screen.
• The row video output allows you to choose between the RGB mode and the classic
mode CVBS. The RGB gives you a better image on most of the television, but you need
to use a scart lead with all its 21 pins cabled.
• The row menu language allows you to change the system language if you have not
done it on the start up page.
• The row audio language allows you to choose the language, which will be chosen by
default when you search for a channel, which emit several languages (Euronews on
Hotbird for example).
• The choice of the language on the row language subtitles is useless on this model.
• The row DiSEqC allows you to choose 1.2 for a motorised reception or 1.0 for a fixed
reception with one a several heads (LNB).
27
13
Radios
The satellites emits not only TV channel, but radios as well in digital quality. You then
advise you to connect the receiver to your Hi-Fi system with 2 RCA / 2 RCA flylead. This
remarks is for the TV channels as well!
When you push on the key Ø, you enter the radio mode. Then, when you push the OK
key the Radios list will appears, and you will not see any image on the screen. The menu
channel list and parental control allow you to personalize the radios list. You can use the
Digital PVR, but the function time-Shift does not work in radio mode. Press on the Ø key
to go back to the TV mode.
14
Electronic stops adjustment
If your motor does not go east home anymore or west home (which means until it mechanical stop), it is probably because an electronic stop prevent it to. You then have to reset
the electronic stops.
• Go into Menu / Motor adjustment / Put the limits.
• Go down on the row erase the limits and press on OK, the button OK flashes.
• Go up on the row movement E/O and press on the arrow 3
• Wait until the satellite dish stops onto its east stops.
• Go down on the row place limit east and press on OK, the button OK flashes.
• Go up onto the row movement E/O and press on the arrow 4
• Wait until the satellite dish stops on its west stops.
• Go down onto the row place the limits west and press on OK, the button OK flashes.
• Press on Exit to leave and come back in TV mode.
15
Mechanicals stop adjustments
Warning: do this adjustment is an absolute necessity.
This adjustment may be necessary if you fixed your motor on a gable. From set up, the
stops are adjusted at 45° East and 45° West.
This adjustment is suitable for a fixing on a gable if your stand off arm is at least at 45cm
from the wall and the wall faces full south.
If it is not the case you need to limit the movement of the dish to avoid it to be damaged
against the wall.
This adjustment must be done when the dish is set up on the motor.
28
Do not unscrew
Fragile wires: correctly
maintains the electrical bloc to avoid pulling out the wires.
ADJUSTMENT PROCEDURE (West the East)
West: from the 0° position, make the motor spin (4) toward the west until the satellite dish
being near the obstacle.
Without unscrewing the big Phillips screw, pull towards you the white cylinder (the top
and the bottom) and then make it spin to make the bottom stops faces the sensor.
East: Make a continuing rotation (4) towards the east until the satellite being near the
obstacle. Pull towards you the white cylinder top part and make it spin until the top stop
touch the sensor. During that adjustment, make sure you do not move the bottom part
(West stop).
Then close the cover, the Stop adjustment is finished.
You need then to validate the new positions of your stop on you receiver. For that, reset(3)
then a satellite validation (step M page 18).
EAST stop
WEST stop
(3)(4)
See the paragraphs on the page 9.
29
16
Use with a VCR
Though that your (Re)playBOX has a digital satellite PVR with a hard drive, you can connect a classical VCR onto the VCR scart. You will then be able to transfer onto cassettes
the movies you had recorded onto the hard drive.
Simply connect your VCR onto the receiver VCR scart input.
To record the digital, the receiver needs to be switch on the channel to record.
Then launch the recording on the VCR AV channel (0, AV, EXT…) See the VCR user
manual for the exact manipulation.
To read a cassette, simple launch the reading, the VCR will automatically take the hand
onto the terminal. If it is not the case, press on the TV/VCR key of your VCR remote control.
To transfer a digital recording onto a cassette, you just have to read this recording while
the VCR records the AV channel.
17
Universal remote control
The universal remote control should be programmed with a code (generally with 3 or 4
digits) to work with an appliance. The code is chosen by the universal remote control
manufacturer, and not the manufacturer of the appliance to be directed. Your receiver has
been recently built, it could happen that some universal remote control will not work with
it, even if the manufacturer supply with Metronic code. If none of the Metronic code functions, try an automatic search. If the automatic search failed, it means that probably the
code from the receiver has not been entered into the universal remote control.
Thank you for understanding that Metronic will not be able to help you on the codes from
a universal remote control which is not from the Metronic brand. It is recommended to
contact the universal remote control manufacturer.
30
18
A
Digital PVR
General points
Your (Re)playBOX contain a hard drive (HD). The hard drive capacity of 40 GigaOctets
allow you to record about 25 hours. The duration is roughly because it depends on the
rate of the emission you are recorded. In general, you need to count 1.5 Go per recording
hour, but some emissions or channels might need 2Go/h or more.
The Digital PVR offers you the classic functions of recording, read, fast forward etc. At the
opposite as the VCR with Band, you have no loss of quality. But the biggest interest about
the digital PVR is the function to allow you to move the time (Time-Shift). The function
allows you to pause on an emission in direct, then “read” again when you want. You can
then answer the phone, for example, without loosing any details of the emission you are
watching. Go to § 18-F for more details.
The hard drive has not been designed as a long last storage tool. Like a computer, you
have some risks of loosing some data. So, if you record an emission or a movie that you
want to keep, we advise you to save it on a cassette, like we explained in § 16.
B
Hard drive adjustment
When you pause on direct (Time-Shifts), the hard drive needs to rotate to not loose anything of the action in progress. If the hard drive is in standby, you need about 10 seconds
to initialise the hard drive. After the switching on and after each use, the hard drive goes
in standby after sometime to save energy and make your (Re)playBOX quieter.
To choose the time after the hard drive goes in standby:
• Go into Menu / Hard Drive
• On the row hard drive standby, choose a duration between 5 to 30 minutes. If you
choose stop, the hard drive goes immediately in standby. If you choose always ON, the
hard drive will always be ready for the Time-Shift.
The Menu / Hard Drive / Hard drive Info gives you some information on the hard drive,
and mainly the size of the disc used. Even if you have not done any recording 10 to 11%
of the disc space is occupied. This is because of the space reserved for the Time-Shift,
which is about 4Go, about 2 hours.
In case of a problem with the digital PVR functioning, you might have to format the hard
drive, like you could do for a computer. Formatting allow you as well to reduce the scanning time at start up, if it taking too long. For that, go into the menu Menu / hard drive /
format, enter the Pin code and wait a few minutes.
Warning: this operation will erase all the recording.
31
C
Recording
To record an emission you are watching, press simply on the key REC and wait a few
seconds. During the recording, the front face display rEC and a red point appear at the
top right of the screen. On the remote control, only the volume, STOP and ON / OFF key
are active.
To stop a recording, press on STOP (<). A window asks you to confirm that you wish to
finish the recording. Press on OK and then you come back in viewing mode.
D
Read
To watch a recording, press on the key List to make appears the recording list (in TV
mode, you can press as well on PLAY). With the arrows 56, highlight the recording you
want to watch and press on OK.
During the reading, you can use the keys:
STOP to go back to the recording list.
PAUSE to do a stop on an image and then restart the reading.
FFW to do a fast forward (several press increase the speed)
REW for a fast backward
I4 SLOW to have a slow moving
4 PLAY to go out for the slow moving mode, fast forward or backward and came back
in reading.
<
;
8
7
E
Programming
To program a recording on a channel, start to watch this channel by pressing its number,
or accessing with the OK key. Press onto the Timer key to enter into the programming
mode.
In case, a first window asks you to confirm the actual hour. If it is exact, go down on save
and press on OK. If not, modify the values or watch a few second a channel, which display the time, which will put the receiver at the right time.
32
With the arrows select the first empty row and press OK to display the recording adjustment window.
• On the row satellite, select with the arrow 34 the satellite which emits the channel to
record.
• On the row starting date, enter the emission date
• On the row starting hour, enter the time when the emission starts.
• On the same way, enter the adequate value in the row ending date ending time.
• On the row Type, choose once for a unique recording, everyday to start the recording
everyday at the same time or weekly to record every week.
• On the row Destination, leave DD, which refers to a recording on the hard drive. The
Choice VCR is to be used if you want to record with your VCR.
• Once your adjustments are finished, go down on recording and press on OK.
F
Time Shift
To do a pause on direct, press simply the key TS or the key PAUSE.
The image freezes, the display shows –tS- then PAUS.
To go back on the emission, press on PLAY, you are in (pre)recorded mode, the display
shows PLAY.
In pre-recorded, you can pause with the key PAUSE and then read again with PLAY. You
can do as well a fast forward with the key FFW. Several following press on FFW make
you go quicker en quicker, which is showed by the FF01, FF02, and FF04 etc. indication
on the display. In fast forward, you can pick up the direct, the terminal show then PLAY.
You can then go out from the pre-recorded mode (have a look further) or stay in prerecorded mode, which allows you to watch a slow-moving action which has just happened (impossible in direct).
To leave the pre-recorded mode, press on STOP then confirm on OK. The display shows
the channel number, you are again in direct.
33
G
Recording management
By pressing on the List key (or PLAY), you make the recording list to appear. The window
indicates the number, the name of the recording, which by default the name of the channel, the duration, and the type of recording (TV or Radio).
You can change the name by selecting the recording with the arrows 56, then by pressing on 4.
• Change the first letter with the arrows 56
• Go to the next one with the key 4
• Modify the second letter the same way, then the third one etc.
• Press on OK to leave and save.
If you push on 4 by mistakes and that you do not want to change the name, press on the
key [Back].
You can erase a recording by pressing on the key Del. After confirming by OK, the recording will be lost definitively. You need to wait a few seconds for the recording to be erased
from the hard drive (roughly 10 seconds for a hour recording).
19
Digital services
The digital emission has sometimes some supplement data giving some functions especially for the digital. The functions describe underneath are accessible only if the broadcaster emit the corresponding data.
34
A
EPG (electronic program guide)
The EPG key allows you to access the Electronic Program Guide. Most of the channels
emit only some information concerning the emission in progress and the following one.
By pressing on OK on the emission in progress, or the following, you access more
detailed information on the emission.
By pressing (Timer) after selecting the following emission, the data from this emission
will enter automatically in a recording.
B
Audio modes
Some emissions are broadcasted in multi-lingual version (VM). This is the case, for the
channel Euronews on HotBird for example, which emit in French, Italian, Spanish, and
English etc.
To change the language, press on the AUDIO key then on the key 4. If several languages
are emitted, the first row change, and you ear another language.
If the Digital audio flux is available (very rare), his presence is indicated by the marks
AC3.
C
Subtitles
The (Re)playBOX is able to display the DVB subtitles. Press on the key (Subt), if the last
row shows a language (SL…), that means a subtitle is available. Press then on 4 to display activated and press on Exit. If the last row displays NONE, that means there is no
subtitles available.
When the subtitle is activated, the sound quality is not guaranteed. To take off the subtitles display, press on (Subt) then on 4 to display deactivated. Leave with [Exit].
20
Common interface (CI)
The double common interface allows you to insert one or two CAM (Control Access
Module). To preserve the precious module and the card which are going in, make sure
you insert and take off the module when the (Re)playBOX is switched off. To take off
the module, press right home on the button situated on the right then take delicately the
module. In case of resistance do not force, the module and the receiver could be damaged and this is not covered by the guarantee.
Even if each slot can receive all the types of module, the processor manages them differently. Then, if a module does work not very well in a slot, try the other one.
35
21
Questions / Answers
•Why does the screen stay black ?
The channel that you want to watch may be encrypted (pay per view). For your information, a broadcaster could emit an encrypted channel with information, which makes the
receiver to believe that the channel is Free To Air. The opposite is possible.
•My motor is jammed, what do I have to do?
(3)
Reset the motor
•Why the motor is not rotating on its entire course?
Some electronic stops prevent the motor from going to its mechanical stops. You need to
position the motor electronic stops at the same place as the mechanical stops:
See §14 page 28.
• At start up the scan is very long
Format the hard drive.
• A Decrypted module is not working
Put it in another slot.
36
(3)
See the paragraphs on the page 9.
In spite of the care we put to manufacture our products and this user manual, you
might come across some difficulties. Do not hesitate to contact us, our specialist are
ready to advise you.
Receiver model : (Re)playBOX
Satellites received :..........................
- Custumers service
Metronic help line
[email protected]
Tél.: 0033(0) 892 350 315
Monday to friday, from 9:00 to 12:00 am
and from 2:00 to 7:00 pm (french hour).
SAV Métronic, BP56, La Tombe,
37320 Esvres sur Indre, FRANCE
We would like to improve our product all the time, could you please send us this Quality Questionnaire (we refund the stamps if you ask for it).
The fact that you return this quality questionnaire at the end of the user manual will
extend your guarantee by 3 months (pieces only).
CERTIFICATE OF GUARANTEE
The receiver is guarantee against any manufacturing fault, parts and labour (see time
of guarantee on packaging). In case of a breakdown, the transport charges outward
are the customer responsibility, the costs carriage back is our responsibility.
To be valid, the certificate of guarantee must be duly filled and send back with the
invoice photocopy or the sales slip.
YOU NEED TO OBTAIN A RETURN AGREEMENT NUMBER
BEFORE ANY SENDING.
CERTIFICATE OF GUARANTEE
Hardware ref: ..............................................................................................
Purchasing date: ..................................................................................................
37
NOTES
38
Digital receiver (Re)playBOX
Your name :...............................................................
Purchasing date :
..................................................
Adress :...................................................................
Purchasing place :
Town :........................................................................
..................................................
Name of the store :
..................................................
Zip code:.............................................................
Tel :...........................................................................
• Product bought:
Fixed digital kit
Motorised digital kit
Digital receiver alone
• Reason of purchase:
Access to digital quality
More channel choice
Foreign channels
• How did you know METRONIC ?
Freinds / parents
Advertising / catalogues
In store
I have already a METRONIC receiver
• Do you already have an installation, if yes, which brand?
yes
no
.................................................................................................................................................
• Did you already use the METRONIC help line ?
yes
no
If yes, what do you think about it ?
.................................................................................................................................................
.................................................................................................................................................
.................................................................................................................................................
In the even of a complete kit purchase:
• Did you install it yourself ?
yes
no
• Did you go through a fitter ?
yes
no
For which amount ?..................
• Which difficulties did you encounter at the time of the installation?
1 Assembly of the plug on the cable
Easy
Difficult
2 Satellite dish assembly
Easy
Difficult
3 Heads (LNBs) assembly
Easy
Difficult
4 Motor assembly
(in the event of motorised kit)
Easy
Difficult
5 Alignment
Easy
Difficult
• Did you isolate the LNBs (heads) ?
yes
METRONIC isolated paste
Other products METRONIC
Silicone
Adhesive tape
Other ..............
no
• Do you think the user manual is user friendly when you have to install, without an installer, a satellite kit?
yes
no
Which modifications would you wish to see?
................................................................................................................................................
................................................................................................................................................
................................................................................................................................................
................................................................................................................................................
• Where did you install your satellite kit?
On a balcony
Sur the roof (chimney...)
On the wall
On the ground
Other .............
• Which cable length did you use ?
5m
10 m
15 m
20 m
30 m
40 m
plus
Other remarks or suggestions :
................................................................................................................................................
................................................................................................................................................
................................................................................................................................................
................................................................................................................................................
................................................................................................................................................
Are you satisfied of your purchase?
yes
Address :
SAV Métronic,
BP56, La Tombe,
37320 Esvres sur Indre, FRANCE
e-mail : [email protected]
40
no
TV channel guide
N°
Name
Channel
number
Channel
name
N° Name
Freq
Emession
frequency
in MHz
Freq.
Pol SR
Rate
symbol
(debit)
Polarity
Pol SR
N° Name
Freq.
Pol SR
36 S4C~ Digidol
12129 V 27500
37 You TV
12129 V 27500
38 Vitality
12129 V 27500
39 Create & Cra
12129 V 27500
40 Sky News
12207 V 27500
41 Sky News
12207 V 27500
42 Sky News
12207 V 27500
43 SNE
12207 V 27500
44 Sky News UK
12207 V 27500
45 Sky News Eir
12207 V 27500
46 TV SHOP
12344 H 27500
47 Reality TV
12344 H 27500
48 FO2
12344 H 27500
49 Shopping Gen
12344 H 27500
50 TVWarehouse.
12344 H 27500
51 Shop America
12344 H 27500
52 TV Warehouse
12344 H 27500
53 Shop 24/7
12344 H 27500
54 JML Direct
12344 H 27500
55 Game Network
12344 H 27500
56 YES
12344 H 27500
57 Shop Smart
12344 H 27500
58 Community
12382 H 27500
59 Going Places
10921 H 22000
ATLANTIC BIRD 3-----------------------------60 BRTV
12543 H 27500
61 GCPE 1
12543 H 27500
62 GCPE 2
12543 H 27500
TELECOM---------------------------------------63 EURONEWS
11648 H 04440
HOTBIRD---------------------------------------64 EWTN
10723 H 29900
65 MTA INTL
10723 H 29900
66 RTL Televisi
11054 H 27500
67 VOX CH
11054 H 27500
68 RTL CH
11054 H 27500
ASTRA28---------------------------------------1 BBC 1 London
10773 H 22000
2 BBC 2 Englan
10773 H 22000
3 BBC NEWS 24
10773 H 22000
4 ETV
10773 H 22000
5 BBC TES 3
10773 H 22000
6 CBBC Channel
10773 H 22000
7 CBeebies
10773 H 22000
8 BBC 1 NI
10773 H 22000
9 TLM(Browser)
10862 H 22000
10 TLMV
10862 H 22000
11 The Betting
10862 H 22000
12 price-drop.t
11954 H 27500
13 Screenshop
11954 H 27500
14 TV Travelsho
11954 H 27500
15 TV Travelsho
11954 H 27500
16 TV Travelsho
11954 H 27500
17 TV Travelsho
11954 H 27500
18 TVTS Mosaic
11954 H 27500
19 TVTS Quad
11954 H 27500
20 QVC
12032 H 27500
21 Q_I
12032 H 27500
22 QVC
12032 H 27500
23 Q_I
12032 H 27500
24 Q_I dir
12032 H 27500
25 QVC Barker
12032 H 27500
26 QVC TSVNOW
12032 H 27500
27 Ideal World
12032 H 27500
28 ITV News
12032 H 27500
29 bid-up.tv
12032 H 27500
30 TCM
12051 V 27500
31 Cni
12051 V 27500
32 CNN
12051 V 27500
33 Travel Deals
12051 V 27500
34 Travel Ch 2
12051 V 27500
35 BBC PARL’MNT
12129 V 27500
41
TV channel guide
N° Name
Freq.
Pol SR
N° Name
HOTBIRD (suite)-------------------------------69 RTL2 AUSTRIA
11054 H 27500
70 CNN
11054 H 27500
71 NBC
11054 H 27500
72 ZDF
11054 H 27500
73 RTL A
11054 H 27500
74 ARTE GERMAN
11060 V 06510
75 ARTE FRENCH
11060 V 06510
76 Kurdsat
11096 H 27500
77 CNL New Life
11096 H 27500
78 Sailing Chan
11096 H 27500
79 TV ROMANIA
11623 V 27500
80 Chai TV
11623 V 27500
81 Live ShowTV
11623 V 27500
82 102.5 HIT Ch
11623 V 27500
83 TLC SAT
11623 V 27500
84 PRO SAT
11623 V 27500
85 Channel SUN
11623 V 27500
86 SEXY SAT TV
11623 V 27500
87 123SAT/69XTV
11623 V 27500
88 ULTRA BLUE T
11623 V 27500
89 Bloomberg Eu
11642 H 27500
90 Bloomberg Ge
11642 H 27500
91 Bloomberg En
11642 H 27500
92 Tel Sell Hom
11642 H 27500
93 Channel Nine
11642 H 27500
94 EDTV
11747 H 27500
95 EDTV SPORT
11747 H 27500
96 EDTV BUSINES
11747 H 27500
97 JAYA TV
11747 H 27500
98 TVE INTERNAC
11785 H 27500
99 CANAL 24 HOR
11785 H 27500
100 TVE INTER. A
11785 H 27500
101 RAINews24
11804 V 27500
102 CAMERA DEPUT 11804 V 27500
103 TELEPACE
11804 V 27500
104 RAISPORTSAT
11804 V 27500
105 RAINettunoSA
11804 V 27500
106 Rai Edu 2
11804 V 27500
107 RAINettunoSA
11804 V 27500
108 SAT2000
11804 V 27500
109 SKY On Air
11843 V 27500
110 Sport Promo
11843 V 27500
111 SKY On Air
11843 V 27500
112 SKY Assist
11881 V 27500
113 Italia 1
11919 V 27500
114 Canale 5
11919 V 27500
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
42
Retequattro
ORT-I
IQRAA
MA3
MBC
Pehla Europe
Pehla Europe
Telesierra
Italiasat
C. Milagro
Sex-View
Telesierra 2
TV7 Tunis
Khabar TV
DunaTV
TV Pika
TizianaSat
ChatGameTV
OTE PROMO
BALKANIA TV
HIGH TV
RTS SAT
TV MAGIC
06 TV
ERT SAT
EXTRA
TRIAL
MKTV
FASHION
SEXY SAT
ADJARA TV
SYRIAN TV
SAT 7
Abu Dhabi TV
RTV Monteneg
Jordan TV
SFi
SRG SSR SAT
IRIB1 PER
IRIB1 ENG
IRIB2 PER
IRIB2 ENG
IRINN
SAHAR1
SAHAR2
AL-ALAM
FEED
Freq.
Pol SR
11919
11938
12015
12015
12015
12015
12015
12092
12092
12092
12092
12092
12149
12149
12149
12149
12149
12149
12188
12188
12188
12188
12188
12188
12188
12188
12188
12188
12245
12245
12245
12380
12380
12380
12380
12380
12399
12399
12437
12437
12437
12437
12437
12437
12437
12437
12437
V
H
H
H
H
H
H
H
H
H
H
H
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
H
H
H
V
V
V
V
V
H
H
H
H
H
H
H
H
H
H
H
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
TV channel guide
N° Name
Freq.
Pol SR
N° Name
HOTBIRD (suite)-------------------------------162 Asianet
12437 H 27500
163 AsianetUK.co
12437 H 27500
164 EbS
12476 H 27500
165 metv
12476 H 27500
166 LibertyTV.co
12476 H 27500
167 SET
12520 V 27500
168 SARDEGNA UNO 12520 V 27500
169 ITV
12520 V 27500
170 Jaam E Jam
12520 V 27500
171 TAPESH
12520 V 27500
172 PUGLIA CHANN
12520 V 27500
173 IPN
12520 V 27500
174 Reform TV
12520 V 27500
175 24ore.tv
12558 V 27500
176 Al Arabiya
12597 V 27500
177 ANN
12597 V 27500
178 BBC World
12597 V 27500
179 EuroNews
12597 V 27500
180 JSTV 1
12597 V 27500
181 JSTV 2
12597 V 27500
182 Sharjah
12654 H 27500
183 Qatar
12654 H 27500
184 Saudi 1
12654 H 27500
185 Kuwait
12654 H 27500
186 Libya
12654 H 27500
187 Sudan
12654 H 27500
188 Oman
12654 H 27500
189 ESC
12654 H 27500
190 Iraq
12654 H 27500
191 Al manar
12654 H 27500
192 Thai TV5
12673 V 27500
193 3ABN
12673 V 27500
194 Tv Moda
12673 V 27500
195 Studio Europ
12673 V 27500
196 E-TV
12673 V 27500
197 Video Itali
12673 V 27500
198 Telemarket
12673 V 27500
199 GAME NETWORK 12673 V 27500
200 PASSIONS
12692 H 27500
201 ONYX
12692 H 27500
202 MEDYA TV
12692 H 27500
203 ABsat PROMO
12692 H 27500
204 TVN
11408 V 27500
205 TVN Siedem
11408 V 27500
206 MANGO 24
11408 V 27500
207 PILOT TV
11408 V 27500
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
43
DAN - Cinema
TV 5 - FBS
TV 5 Europe
FreeX TV
Kurdistan TV
TBNE
Videolina
Telegenova
RTB
TV POLONIA
Tele5
Polonia 1
ITV
Nile TV Inte
Nile News
Bulgaria TV
MEDIOLANUM
Météo Expres
Beur TV
Khalifa TV
RTR-Planet
TFJ
RAI1
RAI2
RAI3
RaiMed
Canale Lavor
Rai Edu 1
RAIMOSAICO
SENATO ITALI
NAPOLI INT.
MAGIC
COUNTDOWN
PLEASURE TV
BVN-TV
RTB INTERNAT
OASI.TV
BLU LINE TV
DANCE TV
SKY Prima Fi
DW-TV Amerik
HB Feed
HB CH.2
TCT WORLD
OLISAT/TVCHI
DAYSTAR
OLISAT/TELEF
Freq.
Pol SR
11137
11137
11137
11137
11137
11137
11137
11137
11137
11513
11513
11513
11513
12539
12539
12539
12539
10911
11034
11034
11034
11034
11766
11766
11766
11766
11766
11766
11766
11766
12303
12303
12303
12303
12303
12303
12303
12303
12303
10992
11143
11143
11179
11179
11179
11179
11179
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
H
H
H
H
H
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
05500
05500
27500
27500
27500
27500
27500
TV channel guide
N° Name
Freq.
Pol SR
N° Name
HOTBIRD (suite)-------------------------------255 Arirang TV
11179 H 27500
256 OLISAT Latin
11179 H 27500
257 Nuvolari
11200 V 27500
258 Leonardo
11200 V 27500
259 Alice
11200 V 27500
260 Sailing Chan
11200 V 27500
261 NOELLO SAT
11200 V 27500
262 Radio Compan
11200 V 27500
263 DeeJay TV
11200 V 27500
264 SuperPippa
11200 V 27500
265 MTI HB6 CH
11200 V 27500
266 NOELLO GOLD
11200 V 27500
267 GAY.TV
11200 V 27500
268 PIEMONTE SAT
11200 V 27500
269 TV5 Asie
11338 V 05632
270 Polsat 1
11413 H 06200
271 Polsat 2
11413 H 06200
272 R13
11823 H 27500
273 ALPHA TV
11823 H 27500
274 HB CHANNEL
12111 V 27500
275 ARM 1
12111 V 27500
276 AL JAZEERA
12111 V 27500
277 Coming Soon
12111 V 27500
278 Mediterraneo
12111 V 27500
279 LUNATEST
12111 V 27500
280 Made In Ital
12111 V 27500
281 Ceramicanda
12111 V 27500
282 DCTV-english
12236 V 13400
283 DCTV-italy
12236 V 13400
284 DCTV-turkish
12236 V 13400
285 DCTV-german
12236 V 13400
286 DCTV-spanish
12236 V 13400
287 DCTV-french
12236 V 13400
288 DCTV-portugu
12236 V 13400
289 Tele 5
12322 H 27500
290 TV Puls
12322 H 27500
ASTRA 19--------------------------------------291 Bibel TV
10832 H 22000
292 TV Puls Info
10832 H 22000
293 Tango TV
10832 H 22000
294 Canal Canari
10979 V 22000
295 Digital+ Pro
10979 V 22000
296 CCV
11435 V 22000
297 Digital+ Pro
11508 V 22000
298 Al-Jazeera C
11567 V 22000
299 RTM 1
11567 V 22000
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
44
ESC 1
TV5 France/S
TV7 Tunisia
ARTE
ARTE
Canal Algeri
RAI Uno
RTP Internat
Deutsche Wel
Sky News
EuroSport Ne
TVC Internat
Andalucia TV
ETB Sat
TeleMadrid S
TV de Galici
MTV Central
Travel
Travel
Travel
CNN Internat
ARD Das Erst
Bayerisches
Hessen Ferns
Arte
Arte
SR Fernsehen
WDR Fernsehe
BR Alpha
Sudwest Fern
BR Alpha
Phoenix
KTO
ProSieben Os
Kabel 1 Schw
Kabel 1 Oest
ProSieben Sc
SAT1 Oesterr
Eins Extra
Eins Festiva
Eins MuXx
MDR Fernsehe
MDR Sachsen
MDR SachsenMDR Thüringe
RBB Brandenb
RBB Berlin
Freq.
Pol SR
11567
11567
11567
11567
11567
11567
11567
11567
11567
11597
11597
11685
11685
11685
11685
11685
11739
11778
11778
11778
11778
11836
11836
11836
11836
11836
11836
11836
11836
11836
11836
11836
11895
12051
12051
12051
12051
12051
12109
12109
12109
12109
12109
12109
12109
12109
12109
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
H
H
H
H
H
H
H
H
H
H
H
V
V
V
V
V
V
H
H
H
H
H
H
H
H
H
22000
22000
22000
22000
22000
22000
22000
22000
22000
22000
22000
22000
22000
22000
22000
22000
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
27500
TV channel guide
N°
Name
Freq.
Pol SR
N° Name
ASTRA 19 (suite)------------------------------347 NDR Fernsehe
12109 H 27500
348 NDR Hamburg
12109 H 27500
349 NDR Niedersa
12109 H 27500
350 NDR Schleswi
12109 H 27500
351 Sudwest Fern
12109 H 27500
352 SAT1 Schweiz
12148 H 27500
353 TV Berlin
12148 H 27500
354 RTL
12187 H 27500
355 Super RTL
12187 H 27500
356 RTL 2
12187 H 27500
357 VOX
12187 H 27500
358 RTL Shop
12187 H 27500
359 FRANCE 5
12207 V 27500
360 TV BREIZH
12207 V 27500
361 PLANETE THAL
12207 V 27500
362 BLOOMBERG TV 12207 V 27500
363 LCP
12207 V 27500
364 TV 6
12226 H 27500
365 MTV2 - The P
12226 H 27500
366 ‘ZIK / XXL
12285 V 27500
367 BBC WORLD
12285 V 27500
368 FASHION-TV
12285 V 27500
369 CANAL CLUB
12324 V 27500
370 MOSAIQUE
12324 V 27500
371 MOSA 2
12324 V 27500
372 MOSA 3
12324 V 27500
373 CA TV
12324 V 27500
374 MOSA 4
12324 V 27500
375 RTL 4
12343 H 27500
376 National Geo
12343 H 27500
377 Discovery Ch
12343 H 27500
378 RTL 5
12343 H 27500
379 Animal Plane
12343 H 27500
380 CA TV Test C
12363 V 27500
381 TV TRWAM
12460 H 27500
382 Pro Sieben
12480 V 27500
383 Kabel 1
12480 V 27500
384 Neun Live
12480 V 27500
385 DSF - Deutsc
12480 V 27500
386 Home Shoppin
12480 V 27500
387 TELE 5
12480 V 27500
388 SAT1
12480 V 27500
389 N24
12480 V 27500
390 sonnenklar.t
12480 V 27500
391 DPC Test Car
12480 V 27500
392 Bloomberg TV
12551 V 22000
Freq.
Pol SR
393 QVC Germany
12551 V 22000
394 Viva Plus
12551 V 22000
395 BVN TV
12574 H 22000
396 TV 5 Europe
12610 V 22000
397 RTBF Sat
12610 V 22000
398 Motors TV
12610 V 22000
399 Motors TV
12610 V 22000
400 Bahn TV
12633 H 22000
401 K-TV
12633 H 22000
402 XXP TV
12633 H 22000
403 Free-X TV
12662 H 22000
404 TV Niepokala
12669 V 22000
405 n-tv
12669 V 22000
406 VIVA
12669 V 22000
407 Otto Shoppin
12669 V 22000
408 ORF 1
12692 H 22000
409 TW1
12692 H 22000
EUTEL_W2-------------------------------------410 SNAI SAT
12608 H 27500
411 SERVICE 7
12608 H 27500
412 RETECAPRI
12608 H 27500
413 ITALIA 9
12608 H 27500
414 SERVICE 11
12608 H 27500
ARABSAT-------------------------------------415 Bahrain TV
11747 V 27500
416 Saudi Arabia
11747 V 27500
417 Kuwait TV
11747 V 27500
418 Jamahirya Sa
11747 V 27500
419 Sudan TV
11747 V 27500
420 Saudi Arabia
11747 V 27500
421 Aj Majd Spac
11747 V 27500
422 Oman TV
11747 V 27500
423 Abu Dhabi TV
11747 V 27500
424 Future Inter
11785 V 27500
425 LBC Sat
11785 V 27500
426 Nagham
11785 V 27500
427 Tele Liban
11785 V 27500
428 NBN
11785 V 27500
429 Al Arabiyah
11785 V 27500
430 Al-Manar TV
11785 V 27500
431 New TV
11785 V 27500
432 MBC 2
11785 V 27500
433 MBC
11785 V 27500
434 Bahrain TV
11843 H 27500
435 Bahrain TV
11843 H 27500
436 Bahrain TV
11843 H 27500
437 MBC
11843 H 27500
45
TV channel guide
N° Name
Freq.
Pol SR
N° Name
ARABSAT (suite)-----------------------------438 MBC 2
11843 H 27500
439 Al-Arabiyah
11843 H 27500
440 Abu Dhabi TV
11843 H 27500
441 Rotana Music
11843 H 27500
442 Emirates Cha
11862 V 27500
443 Abu Dhabi TV
11862 V 27500
444 Al Mustakill
11938 V 27500
445 TV 7 (Tunisi
11938 V 27500
446 Syria Satell
11938 V 27500
447 Sharjah TV
11938 V 27500
448 Al-Jazeera S
11938 V 27500
TURKSAT---------------------------------------449 BRT 1
10968 V 04557
450 Türkiye Joke
10975 V 05632
451 Gala
11025 V 06510
452 SuperSport
11025 V 06510
453 DHA Feed
11040 H 04000
454 ANS Producti
11047 H 03700
455 Show TV Feed
11063 V 03100
456 TRT Feeds
11066 H 05632
457 Show TV Feed
11063 V 03100
458 TRT 1
11083 V 05632
459 TRT 2
11092 V 05632
460 TRT Internat
11101 V 05632
461 Flash TV
11129 V 04268
462 Kanal 7
11135 V 04444
463 Kanal A
11159 V 03150
464 CNN Turk
11587 V 03670
465 TRT 1
11728 V 27518
466 TV 8 Avrupa
11830 V 06666
467 The History
11868 V 04510
468 Number One T
11868 V 04510
469 Meltem TV
11874 V 03400
470 NTV
11988 V 12800
471 CNBC-e
11988 V 12800
472 Discovery Ch
11988 V 12800
473 Discovery Ch
11988 V 12800
474 Eurasiasat p
12130 V 11719
475 BBC World In
12130 V 11719
476 BK TV Sat
12590 V 03003
477 Ulusal Kanal
12743 H 02285
478 Eyilik TV
12748 H 02400
HISPASAT--------------------------------------479 Tele Loc
11615 V 27500
480 TV TeleL
11615 V 27500
481 TBN Enla
11615 V 27500
Freq.
Pol SR
482 Canal 47
11615 V 27500
483 Canal 35
11615 V 27500
484 TV Amist
11615 V 27500
485 Wonderfu
11615 V 27500
486 Mana-Eur
11682 V 03800
487 Nueva Er
11731 H 28120
488 Canal 4
11731 H 28120
489 European
11731 H 28120
490 E-Quinie
11731 H 28120
491 Canal Pa
11731 V 27500
492 Cadena L
11771 H 28120
493 TV Galic
11811 V 27500
494 Via Loca
11932 H 27500
495 Vision L
11932 H 27500
496 Tu Farma
11932 H 27500
497 Movida L
11932 H 27500
498 Max Loca
11932 H 27500
499 Gigashop
11932 H 27500
500 Rede Rec
11932 H 27500
501 Popular
11932 H 27500
502 VVR
11932 H 27500
503 VVR
11932 H 27500
504 Digital+
11932 V 27500
505 Eurospor
11972 V 27500
506 Megatrix
11972 V 27500
507 Canal 21
12015 V 27500
508 TVE Inte
12711 V 27500
509 CNBC Eur
12711 V 27500
SIRIUS-----------------------------------------510 RTL9
11370 V 03260
ASTRA Canal sat -----------------------------511 SEASONS
11817 V 27500
512 C CINEMA EMO
11817 V 27500
513 C CINEMA FRI
11817 V 27500
514 EURONEWS
11817 V 27500
515 CANAL JIMMY
11817 V 27500
516 MEZZO
11817 V 27500
517 LA CHAINE ME
11817 V 27500
518 SPORT+
11817 V 27500
519 I>TELE
11817 V 27500
520 CANAL+
11856 V 27500
521 CANAL+ BLEU
11856 V 27500
522 CANAL+ JAUNE 11856 V 27500
523 CANAL+ 16/9
11856 V 27500
524 C CINEMA PRE
11856 V 27500
525 DISNEY CHANN
11856 V 27500
526 CANAL+ VERT
11856 V 27500
46
TV channel guide
N° Name
Freq.
Pol SR
N°
ASTRA Canal Sat (suite)---------------------527 EQUIDIA
11856 V 27500
528 PMU sur Cana
11856 V 27500
529 PAD
11856 V 27500
530 C CINEMA AUT
11895 V 27500
531 MCM
11895 V 27500
532 MCM 2
11895 V 27500
533 MATCH TV
11895 V 27500
534 CINE INFO
11895 V 27500
535 TiJi
11895 V 27500
536 NAT GEOGRAPH 11895 V 27500
537 GOURMET TV
11895 V 27500
538 TEST CDN 8
11895 V 27500
539 EUROSPORT
11934 V 27500
540 TMC
11934 V 27500
541 PLANETE
11934 V 27500
542 PARIS PREMIE
11934 V 27500
543 VOYAGE
11934 V 27500
544 LCI
11934 V 27500
545 CANAL J
11934 V 27500
546 SANTE-VIE
11934 V 27500
547 CUISINE.TV
11934 V 27500
548 FRANCE 2
12012 V 27500
549 FRANCE 3
12012 V 27500
550 CANAL EVENEM 12012 V 27500
551 RTL9
12012 V 27500
552 CANAL EVENEM 12012 V 27500
553 TRACE BY MCM
12012 V 27500
554 TELE MELODY
12012 V 27500
555 ESPN CLASSIC
12012 V 27500
556 TEST CDN 4
12012 V 27500
557 RFO SAT.
12207 V 27500
558 CANALPRO TV
12207 V 27500
559 AB MOTEURS
12285 V 27500
560 AB 1
12285 V 27500
561 ANIMAUX
12285 V 27500
562 ENCYCLOPEDIA 12285 V 27500
563 ESCALES
12285 V 27500
564 toute L’ HIS
12285 V 27500
565 RFM-TV
12285 V 27500
566 ACTION
12285 V 27500
567 MANGAS
12285 V 27500
568 CINE BOX
12285 V 27500
569 Csat Interac
12324 V 27500
570 MMD
12324 V 27500
571 DEMAIN !
12402 V 27500
572 COMEDIE !
12402 V 27500
Name
Freq.
Pol SR
573 13EME RUE
12402 V 27500
574 FOX KIDS
12402 V 27500
575 L’EQUIPE TV
12402 V 27500
576 PLANETE FUTU
12402 V 27500
577 C CINEMA CLA
12402 V 27500
578 C CINEMA SUC
12402 V 27500
579 GAME ONE
12402 V 27500
580 C CINEMA 16/
12640 V 22000
581 CINE POLAR
12640 V 22000
582 CINE FX
12640 V 22000
583 CINE COMIC
12640 V 22000
584 TEVA
12640 V 22000
585 DISNEY CHANN
12640 V 22000
586 PLAYHOUSE DI
12640 V 22000
587 TOON DISNEY
12640 V 22000
588 CLUB TELEACH
12640 V 22000
HOTBIRD TPS---------------------------------589 Cinéstar 1
10758 V 27500
590 Cinéstar 2
10758 V 27500
591 Cinétoile
10758 V 27500
592 TPS star
10758 V 27500
593 Cinéfaz
10758 V 27500
594 Infosport
10796 V 27500
595 Eurêka!
10796 V 27500
596 Série Club
10796 V 27500
597 Fun TV
10796 V 27500
598 Teva
10796 V 27500
599 Télétoon
10796 V 27500
600 Festival
10796 V 27500
601 M6 Music
10796 V 27500
602 Club Téléach
10796 V 27500
603 LCI
10834 V 27500
604 FRANCE 5
10834 V 27500
605 FRANCE 2
10834 V 27500
606 Eurosport
10834 V 27500
607 FRANCE 3
10834 V 27500
608 PARIS PREMIE
10834 V 27500
609 ARTE
10834 V 27500
610 I TELE
10834 V 27500
611 RTM
10873 V 27500
612 Star Academy
10873 V 27500
613 EQUIDIA
10873 V 27500
614 ESPN CLASSIC
10873 V 27500
615 CINE INFO
10873 V 27500
616 BBC PRIME
10873 V 27500
617 TV BREIZH
10873 V 27500
618 LA CHAINE PA
10873 V 27500
47
TV channel guide
N° Name
Freq.
Pol SR
HOTBIRD TPS (suite)------------------------619 Equidia Alph
10873 V 27500
620 M6
10911 V 27500
621 HISTOIRE
10911 V 27500
622 TF1
10911 V 27500
623 TFOU
10911 V 27500
624 Odyssée
10911 V 27500
625 TF6
10911 V 27500
626 RFO SAT
10911 V 27500
627 Télétoon+1
10911 V 27500
628 CCTV9
11034 V 27500
629 KTO
11034 V 27500
630 God TV
11034 V 27500
631 Boomerang
11034 V 27500
632 SIC
11034 V 27500
633 AB 1
11681 H 27500
634 AB MOTEURS
11681 H 27500
635 ANIMAUX
11681 H 27500
636 CHASSE & PEC
11681 H 27500
637 ZIK / XXL
11681 H 27500
638 ‘ZIK
11681 H 27500
639 XXL
11681 H 27500
640 MUSIQUE CLAS
11681 H 27500
641 ESCALES
11681 H 27500
642 FIT/ toute L
11681 H 27500
643 RFM-TV
11681 H 27500
644 ACTION
11681 H 27500
645 MANGAS
11681 H 27500
646 ENCYCLOPEDIA 11681 H 27500
647 RTL9
11681 H 27500
48
Node Park Touraine
BP 1 TAUXIGNY
37310 REIGNAC SUR INDRE
CEDEX FRANCE
www.metronic.com
Product made in Asia