PICKIT 1 Demo Board (6LEDs) Based On PIC 12F629 User`s Guide

PICKIT 1 Demo Board (6LEDs) Based On PIC 12F629 User`s Guide

PICKIT 1 Demo Board (6LEDs)
Based On PIC 12F629
User’s Guide
© 2004-2008 Sure Electronics Inc.
DB-DP121-Ver1.0
PICKIT 1 Demo Board (6LEDs)
Based On PIC 12F629
User’s Guide
Table of contents
Chapter1.Brief Introduction of PICKIT 1 Demo Board ............................................1
Chapter2.Fast Guide ........................................................................................................2
Chapter3.Schematics and Physical Dimension .......................................................4
3-1.
3-2.
Schematics........................................................................................................4
Physical Dimension..........................................................................................5
Chapter4. Contact Us.......................................................................................................6
© 2004-2008 Sure Electronics Inc.
DB-DP121-Ver1.0-page i
PICKIT 1 Demo Board (6LEDs)
Based On PIC 12F629
User’s Guide
Table of contents
NOTES:
Product Version
：
Ver 1.0
Document Version
：
Ver 1.0
DB-DP121-Ver1.0-page ii
© 2004-2008 Sure Electronics Inc.
PICKIT 1 Demo Board (6LEDs)
Based On PIC 12F629
User’s Guide
Chapter1.Brief Introduction of PICKIT 1 Demo Board
Overview
Figure 1
1. USB power supply.
2. Programmable
3. Encoder controls the circuit of LEDs and keys.
3. By changing the keys state, LED has two flicking modes.
4. In-Circuit Serial Programming.
5. There is a layer of rubber on the backside to protect your hands from wound.
6. Operating Environment Temperature Range: 0~+55℃.
7. Storage Environment Temperature Range:-25~+85℃.
© 2004-2008 Sure Electronics Inc.
DB-DP121-Ver1.0-page 1
PICKIT 1 Demo Board (6LEDs)
Based On PIC 12F629
User’s Guide
Chapter2.Fast Guide
Figure 2
1. All of the encoders are set ON.
2. Connect to USB power supply.
3. Key SW1 is used to switch lights on in turn. The order is 3D1, 3D2, 2D1, 2D2, D1, D2
4. Key SW2 is used to change the blinking frequency.
Encoder position setting
Components’ control
Encoder Position Setting①②③
SW1’s control
SW3
DB-DP121-Ver1.0-page 2
© 2004-2008 Sure Electronics Inc.
Fast Guide
SW2’s control
SW3
Led’s control
SW3
Notice:
Closing encoder (SW3) before programming.
© 2004-2008 Sure Electronics Inc.
DB-DP121-Ver1.0-page 3
PGC
GP2
GP5
GP4
MCLR
PGD
1
2
3
4
5
6
12
11
10
9
8
7
SW DIP-6
SW3
KEY 1
KEY 2
100R
1
2
3
4
R6
1
50R
2
241
2
181
2
R4
1
R5
1
101
2
R3
1
R
G
B
R2
3D1
100R PGD
PGC
GP2
2
8
7
6
5
LED
1
3D2
LED
2D1
1
LED
2D2
LED
LED
D1
+5V_USB
LED
D2
MCLR
PGC
PGD
6
5
4
3
2
1
475
J2
ICSP
104
+5V_USB
104
C5
4
SW
2
SW2
KEY 1
472
R7
+5V_USB
104
C4
C3
C2
C1
475
+5V_USB
+5V_USB
+5V_USB
+5V_USB
1
2
PIC12F629
1
2
VSS
VDD
GP5 GP0/PGD
GP4 GP1/PGC
GP3/MCLR GP2
3
R
2
1
1
U1
2
G
C
2
3
R
1
G
C
1
2
1
2
GP5
GP4
MCLR R 1
4
R
1
G
C
3
B
4
R
2
B
2
1
3
1
2
1
2
G
C
3
1
2
3
4
J1
USB
104
C6
4
SW
2
SW4
KEY 2
472
R8
+5V_USB
VBUS
DD+
GND
1
2
6
5
2
1
DB-DP121-Ver1.0-page 4
3
3-1.
1
+5V_USB
PICKIT 1 Demo Board (6LEDs)
Based On PIC 12F629
User’s Guide
Chapter3.Schematics and Physical Dimension
Schematics
Figure 2
© 2004-2008 Sure Electronics Inc.
Schematics and Physical Dimension
Notice: The above schematics are just for reference. There may be a little difference in
production batch.
3-2.
Physical Dimension
Figure 3
© 2004-2008 Sure Electronics Inc.
DB-DP121-Ver1.0-page 5
PICKIT 1 Demo Board (6LEDs)
Based On PIC 12F629
User’s Guide
Chapter4. Contact Us
Sure Electronics Co., Ltd.
Floor 5, A zone,
Qinhuai Technology Innovation center,
NO.105-2, DaMing Road,
Nanjing,
China
Tel:
+8613601408832
+86-25-66606340
(English service, from GMT1-10AM, only for technical questions)
Email:
[email protected]
Website:
www.sure-electronics.net
www.sure-electronics.com
www.sureelectronics.net
DB-DP121-Ver1.0-page 6
© 2004-2008 Sure Electronics Inc.