JVC KD-G302 User Guide Manual - CaRadio

Transcription

ENGLISH
DEUTSCH
CD RECEIVER
CD-RECEIVER
RECEPTEUR CD
CD-RECEIVER
FRANÇAIS
KD-G302/KD-G301
NEDERLANDS
KD-G302
KD-G301
• This unit is equipped with the display demonstration. To cancel it, see page 6.
• Dieses Gerät ist mit einer Demonstrationsfunktion für das Display ausgestattet. Auf Seite 6 wird
beschrieben, wie Sie diese Demonstrationsfunktion deaktivieren können.
• Cet appareil est équipé d’une fonction de démonstration des affichages. Pour l’annuler, référez-vous
à la page 6.
• Dit toestel heeft een display-demonstratiefunctie. Zie bladzijde 6 voor het annuleren van deze
functie.
For installation and connections, refer to the separate manual.
Für den Einbau und die Anschlüsse siehe das eigenständige Handbuch.
Pour l’installation et les raccordements, se référer au manuel séparé.
Bijzonderheden over de installatie en aansluiting van het apparaat vindt u in de
desbetreffende handleiding.
INSTRUCTIONS
BEDIENUNGSANLEITUNG
MANUEL D’INSTRUCTIONS
GEBRUIKSAANWIJZING
GET0187-001A
Downloaded from Caradio-Manual.com Manuals
[E/EX]
ENGLISH
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all
servicing to qualified service personnel.
3. CAUTION: Visible and invisible laser radiation when open and interlock failed or defeated. Avoid
direct exposure to beam.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.
How to reset your unit
After detaching the control panel, press the
reset button on the panel holder using a ballpoint pen or a similar tool.
This will reset the built-in microcomputer.
Note:
Your preset adjustments—such as preset channels
or sound adjustments—will also be erased.
How to use the MODE button
If you press MODE, the unit goes into functions mode, then the number buttons and 5/∞ buttons
work as different function buttons.
Ex.: When number button 2 works as MO (monaural) button.
Time countdown indicator
To use these buttons for original functions again after pressing MODE, wait for 5 seconds
without pressing any of these buttons until the functions mode is cleared.
• Pressing MODE again also clears the functions mode.
2 Downloaded from Caradio-Manual.com Manuals
Thank you for purchasing a JVC product. Please read all instructions carefully before operation,
to ensure your complete understanding and to obtain the best possible performance from the unit.
How to reset your unit ...............................
How to use the MODE button ...................
2
2
LOCATION OF THE BUTTONS ............ 4
OTHER MAIN FUNCTIONS ................ 23
Changing the general settings (PSM) ....... 23
Detaching the control panel ...................... 26
4
CD CHANGER OPERATIONS .............. 27
BASIC OPERATIONS ....................... 5
About MP3 discs ....................................... 27
Playing discs ............................................. 28
Selecting the playback modes .................. 30
Control panel .............................................
Turning on the power ................................
Canceling the display demonstration ........
Setting the clock ........................................
5
6
7
EXTERNAL COMPONENT OPERATIONS ... 31
RADIO OPERATIONS ...................... 8
Playing an external component ................. 31
Listening to the radio ................................. 8
Storing stations in memory ....................... 9
Tuning in to a preset station ...................... 10
DAB TUNER OPERATIONS ................ 32
RDS OPERATIONS ......................... 11
What you can do with RDS ....................... 11
Other convenient RDS functions and
adjustments ............................................ 16
CD OPERATIONS ........................... 18
Playing a CD .............................................
Locating a track or a particular portion
on a CD ..................................................
Selecting CD playback modes ..................
Prohibiting CD ejection .............................
18
19
20
20
ENGLISH
CONTENTS
Tuning in to an ensemble and one of the
services ..................................................
Storing DAB services in memory ..............
Tuning in to a preset DAB service .............
What you can do more with DAB ..............
32
33
34
35
USING THE REMOTE CONTROLLER ..... 36
Location of the buttons .............................. 37
TROUBLESHOOTING ...................... 38
MAINTENANCE ............................. 40
Handling discs ........................................... 40
SPECIFICATIONS ........................... 41
SOUND ADJUSTMENTS ................... 21
Selecting preset sound modes
(C-EQ: custom equalizer) ....................... 21
Adjusting the sound .................................. 22
Note:
For security reasons, a numbered ID card is provided with this unit, and the same ID number is imprinted on
the unit’s chassis. Keep the card in a safe place, as it will help the authorities to identify your unit if stolen.
BEFORE USE
*For safety....
• Do not raise the volume level too much, as this will
block outside sounds, making driving dangerous.
• Stop the car before performing any complicated
operations.
*Temperature inside the car....
If you have parked the car for a long time in hot
or cold weather, wait until the temperature in the
car becomes normal before operating the unit.
3
ENGLISH
LOCATION OF THE BUTTONS
Control panel
Display window
1
(standby/on/attenuator) button
2 SEL (select) button
3 TP PTY (traffic programme/programme type)
button
4 FM/AM DAB button
5 CD CD-CH (CD changer) button
6 Display window
7 0 (eject) button
8 5 (up) button
+10 button
9
(control panel release) button
p Control dial
q Number buttons
w EQ (equalizer) button
e Remote sensor
• You can control this receiver with an optionally
purchased remote controller.
r MO (monaural) button
t SSM (Strong-station Sequential Memory)
button
y RPT (repeat) button
u RND (random) button
i MODE button
o DISP (display) button
;
4/¢
buttons
a ∞ (down) button
–10 button
Display window
s Main display
d EQ (equalizer) indicator
f Sound mode (C-EQ: custom equalizer)
indicators—ROCK, CLASSIC, POPS,
HIP HOP, JAZZ, USER
•
also works as level meter during play if
the level meter is activated (see page 25).
g MP3 indicator
• Lights up only when playing an MP3 disc on a
JVC MP3-compatible CD changer.
h Tuner reception indicators—ST (stereo),
MO (monaural)
j RDS indicators—TP, PTY, AF, REG
k CD indicator
l CH (CD changer) indicator
/ Playback mode/item indicators—RND (random),
(disc), RPT (repeat)
z LOUD (loudness) indicator
x Source display
Volume level indicator
c Tr (track) indicator
ENGLISH
BASIC OPERATIONS
1
3
2
Turning on the power
1
Turn on the power.
Note on One-Touch Operation:
When you select a source in step 2 below, the
power automatically comes on. You do not have
to press this button to turn on the power.
2
Volume level indicator
4
Adjust the sound as you want. (See
pages 21 and 22.)
Select the source.
To drop the volume in a moment
To operate the tuner (FM or AM),
see pages 8 – 17.
To play a CD,
see pages 18 – 20.
To operate the CD changer,
To operate the external component
(LINE IN), see page 31.
To operate the DAB tuner,
3
Volume level appears.
Adjust the volume.
Press
briefly while listening to any
source. “ATT” starts flashing on the display, and
the volume level will drop in a moment.
To resume the previous volume level, press the
button briefly again.
• If you turn the control dial, you can also restore
the sound.
To turn off the power
Press and hold
for more than one
second.
“SEE YOU” appears, then the unit turns off.
• If you turn off the power while listening to a
disc, disc play will start from where playback
has been stopped previously, next time you
turn on the power.
To increase the volume
To decrease the volume
CAUTION on Volume Setting:
Discs produce very little noise compared with
other sources. If the volume level is adjusted for
the tuner, for example, the speakers may be
damaged by the sudden increase in the output
level. Therefore, lower the volume before playing a
disc and adjust it as required during playback.
5
ENGLISH
Canceling the display
demonstration
3
When shipped from the factory, display
demonstration has been activated, and starts
automatically when no operations are done for
about 20 seconds.
• It is recommended to cancel the display
demonstration before you use the unit for the
first time.
To cancel the display demonstration, follow
the procedure below:
1
Select “DEMO OFF.”
DEMO OFF
4
DEMO ON
Finish the setting.
Press and hold SEL (select) for more
than 2 seconds so that one of the
PSM items appears on the display.
(PSM: see pages 23 and 24.)
To activate the display demonstration, repeat
the same procedure and select “DEMO ON” in
step 3.
2
Select “DEMO” if not shown on the
display.
ENGLISH
Setting the clock
5
Finish the setting.
You can also set the clock system to either
24 hours or 12 hours.
1
2
Set the hour.
1 Select “CLOCK H” (hour) if not shown on
the display.
2 Adjust the hour.
1
2
To check the current clock time or change the
display mode
Press DISP (display) repeatedly.
Each time you press the button,
the display changes as follows:
• During AM and FM non-RDS Station
operation:
Frequency
Clock
• During FM RDS Station operation:
Station name
Clock
3
Set the minute.
1 Select “CLOCK M” (minute).
2 Adjust the minute.
1
2
Station frequency
Programme type
• During CD operation:
Elapsed playing time
Clock
• During CD changer operation:
Disc number
Clock
4
• During external component operation:
Set the clock system.
1 Select “24H/12H.”
2 Select “24H” or “12H.”
1
2
LINE IN
Clock
• During power off:
The power turns on and the clock time is
shown for 5 seconds, then the power turns off.
7
ENGLISH
RADIO OPERATIONS
Listening to the radio
You can use either automatic searching or manual
searching to tune in to a particular station.
Searching for a station automatically:
Auto search
1
To stop searching before a station is
received, press the same button you have
pressed for searching.
Searching for a station manually:
Manual search
1
Each time you press the
button, the band changes as
follows:
follows:
FM1
FM2
FM3
FM1
AM
FM2
FM3
AM
Note:
This receiver has three FM bands (FM1, FM2,
FM3). You can use any one of them to listen to
an FM broadcast.
Selected band appears.
2
Lights up when receiving an FM stereo
broadcast with sufficient signal strength.
Note:
This receiver has three FM bands (FM1, FM2,
FM3). You can use any one of them to listen to
an FM broadcast.
2
Select the band (FM1 – 3, AM).
Start searching for a station.
To search for stations of
higher frequencies
To search for stations of lower frequencies
When a station is received, searching stops.
Press and hold ¢
or
4
until “M” (manual) starts flashing on
the display.
Tune in to a station you want while
“M” (manual) is still flashing.
To tune in to stations of
higher frequencies
Storing stations in memory
ENGLISH
3
You can use one of the following two methods to
store broadcasting stations in memory.
• Automatic preset of FM stations: SSM (Strongstation Sequential Memory)
• Manual preset of both FM and AM stations
To tune in to stations of lower frequencies
FM station automatic preset: SSM
• If you release your finger from the button,
the manual mode will automatically turns
off after 5 seconds.
• If you hold down the button, the frequency
keeps changing (in 50 kHz intervals for
FM and 9 kHz for AM—MW/LW) until you
release the button.
You can preset 6 local FM stations in each FM
band (FM1, FM2, and FM3).
1
follows:
When an FM stereo broadcast is hard to
receive:
FM1
1 Press MODE to enter the
functions mode while listening
to an FM stereo broadcast.
2
2 Press MO (monaural), while
“MODE” is still flashing on the
display, so that “MONO”
appears on the display.
monaural mode turns on and off
alternately.
Select the FM band (FM1 – 3) you
want to store FM stations into.
3
FM2
FM3
AM
Press MODE to enter the functions
mode.
Press and hold SSM for about
2 seconds.
MO (monaural) indicator
When the MO indicator is lit on the display, the
sound you hear becomes monaural but the
reception will be improved.
“SSM” flashes, then disappears
when automatic preset is over.
Local FM stations with the strongest signals are
searched and stored automatically in the band
number you have selected (FM1, FM2, or FM3).
These stations are preset in the number buttons
—No.1 (lowest frequency) to No.6 (highest
frequency).
When automatic preset is over, the station stored
in number button 1 will be automatically tuned in.
9
ENGLISH
4
Manual preset
You can preset up to 6 stations in each band
(FM1, FM2, FM3, and AM) manually.
Ex.: Storing FM station of 92.5 MHz into the
preset number 1 of the FM1 band.
1
Select the band (FM1 – 3, AM) you
want to store stations into (in this
example, FM1).
follows:
FM1
2
FM2
FM3
AM
Tune in to a station (in this example,
of 92.5 MHz).
To tune in to stations of
higher frequencies
Repeat the above procedure to store
other stations into other preset
numbers.
Notes:
• A previously preset station is erased when a new
station is stored in the same preset number.
• Preset stations are erased when the power supply to
the memory circuit is interrupted (for example,
during battery replacement). If this occurs, preset
the stations again.
Tuning in to a preset station
You can easily tune in to a preset station.
Remember that you must store stations first. If
you have not stored them yet, see “Storing
stations in memory” on pages 9 and 10.
1
follows:
To tune in to stations of lower frequencies
FM1
2
3
Press and hold the number button
(in this example, 1) for more than
2 seconds.
Preset number flashes for a while.
FM2
FM3
AM
Select the number (1 – 6) for the
preset station you want.
RDS OPERATIONS
RDS (Radio Data System) allows FM stations to
send an additional signal along with their regular
programme signals. For example, the stations
send their station names, as well as information
about what type of programme they broadcast,
such as sports or music, etc.
Another advantage of RDS function is called
“Enhanced Other Networks.” By using the
Enhanced Other Networks data sent from a
station, you can tune in to a different station of a
different network broadcasting your favorite
programme or traffic announcement while
listening to another programme or to another
source such as CD.
By receiving the RDS data, this unit can do the
following:
• Tracing the same programme automatically
(Network-Tracking Reception)
• Standby Reception of TA (Traffic
Announcement) or your favorite programme
• PTY (Programme Type) search
• Programme search
• And some other functions
Tracing the same programme
automatically (Network-Tracking
Reception)
When driving in an area where FM reception is
not good, the tuner built in this unit automatically
tunes in to another RDS station, broadcasting the
same programme with stronger signals. So, you
can continue to listen to the same programme in
its finest reception, no matter where you drive.
(See the illustration on page 17.)
Two types of the RDS data are used to make
Network-Tracking Reception work correctly
—PI (Programme Identification) and AF
(Alternative Frequency).
Without receiving these data correctly from the
RDS station you are listening to, NetworkTracking Reception will not operate.
To use Network-Tracking Reception
You can select the different modes of networktracking reception to continue listening to the
same programme in its finest reception.
When shipped from the factory, “AF” is selected.
• AF:
ENGLISH
What you can do with RDS
Network-Tracking Reception is
activated with Regionalization set to
“off.”
With this setting, the unit switches to
another station within the same
network when the received signals
from the current station become
weak. (In this mode, the programme
may differ from the one currently
received.)
The AF indicator lights up but the
REG indicator does not.
• AF REG: Network-Tracking Reception is
activated with Regionalization set to
“on.”
With this setting, the unit switches to
another station, within the same
network, broadcasting the same
programme when the received
signals from the current station
become weak.
Both the AF indicator and the REG
indicator light up.
• OFF:
Network-Tracking Reception is
deactivated.
Neither the AF indicator nor the REG
indicator lights up.
AF and REG indicators
Note:
If a DAB tuner is connected and Alternative Reception
(for DAB services) is activated, Network-Tracking
Reception is also activated (“AF”) automatically. On
the other hand, Network-Tracking Reception cannot
be deactivated without deactivating Alternative
Reception. (See page 35.)
CONTINUED ON THE NEXT PAGE
11
ENGLISH
1
Using TA Standby Reception
TA Standby Reception allows the unit to switch
temporarily to Traffic Announcement (TA) from
the current source (another FM station, CD, or
other connected components).
• TA Standby Reception will not work if you are
listening to an AM station.
2
3
4
Press TP PTY to activate TA Standby Reception.
Select “AF-REG” (alternative
frequency/regionalization reception)
if not shown on the display.
Select the desired mode—“AF,”
“AF REG,” or “OFF.”
Finish the setting.
7 When the current source is FM, the TP
indicator either lights up or flashes.
• If the TP indicator lights up, TA Standby
Reception is activated.
If a station starts broadcasting a traffic
announcement, “TRAFFIC” appears on the
display, and this unit automatically tunes in to
the station. The volume changes to the
preset TA volume level (see page 16) and the
traffic announcement can be heard.
• If the TP indicator flashes, TA Standby
Reception is not yet activated since the
station being received does not provide the
signals used for TA Standby Reception.
To activate TA Standby Reception, you need
to tune in to another station providing these
signals. Press ¢
or
4 to search
for such a station.
When a station providing these signals is
tuned in, the TP indicator stops flashing and
remains lit. Now TA Standby Reception is
activated.
7 When the current source is other than FM,
the TP indicator lights up.
If a station starts broadcasting a traffic
announcement, “TRAFFIC” appears on the
display, and this unit automatically changes the
source and tunes in to the station.
To deactivate the TA Standby Reception,
press TP PTY again. The TP indicator
disappears.
4
Finish the setting.
PTY Standby Reception allows the unit to switch
temporarily to your favorite programme (PTY:
Programme Type) from the current source
(another FM station, CD, or other connected
components).
• PTY Standby Reception will not work if you are
listening to an AM station.
You can select your favorite programme type for
PTY Standby Reception.
When shipped from the factory, PTY Standby
Reception is turned off. (“OFF” is selected for
PTY Standby Reception.)
1
2
3
Select “PTY-STBY” (standby) if not
shown on the display.
Select one of the twenty-nine PTY
codes. (See page 17.)
Selected code name
appears on the display
and is stored into
memory.
ENGLISH
Using PTY Standby Reception
7 When the current source is FM, the PTY
indicator either lights up or flashes.
• If the PTY indicator lights up, PTY Standby
If a station starts broadcasting the selected
PTY programme, this unit automatically
tunes in to the station.
• If the PTY indicator flashes, PTY Standby
Reception is not yet activated since the
station being received does not provide the
signals used for PTY Standby Reception.
To activate PTY Standby Reception, you
need to tune in to another station providing
these signals. Press ¢
or
4 to
search for such a station.
When a station providing these signals is
tuned in, the PTY indicator stops flashing
and remains lit. Now PTY Standby Reception
is activated.
7 When the current source is other than FM,
the PTY indicator lights up.
If a station starts broadcasting the selected
PTY programme, this unit automatically
changes the source and tunes in to the station.
To deactivate the PTY Standby Reception,
select “OFF” in step 3 on the left column. The
PTY indicator disappears.
13
ENGLISH
Searching your favorite programme
3
You can search any one of the PTY codes.
In addition, you can store your 6 favorite
programme types in the number buttons.
When shipped from the factory, the following
6 programme types have been stored in the
number buttons (1 to 6).
for more than 2 seconds to store the
PTY code selected into the preset
number you want.
To store your favorite programme types, see
below.
To search your favorite programme type, see
page 15.
1
POP M
2
ROCK M
3
EASY M
4
CLASSICS
5
AFFAIRS
6
VARIED
Selected PTY code and
“MEMORY” appear
alternately for a while.
To store your favorite programme types
1
Press and hold TP PTY for more
than 2 seconds while listening to an
FM station.
4
The last selected PTY code appears.
2
Select one of the twenty-nine PTY
codes. (See page 17.)
Selected code name
than 2 seconds to exit from this
mode.
1
Press ¢
or
4 to start PTY
search for your favorite programme.
than 2 seconds while listening to an
FM station.
The last selected PTY code appears.
2
3
To select one of your favorite
programme type
ENGLISH
To search your favorite programme type
• If there is a station broadcasting a programme
of the same PTY code as you selected, that
station is tuned in.
• If there is no station broadcasting a
programme of the same PTY code as you
selected, the station will not change.
Note:
In some areas, the PTY search will not work correctly.
or
To select any one of the twenty-nine
PTY codes
Ex.: When “ROCK M” is selected
15
ENGLISH
Other convenient RDS
functions and adjustments
Automatic selection of the station
when using the number buttons
Usually when you press the number button, the
preset station is tuned in.
However, when the preset station is an RDS
station, something different will happen. If the
signals from that preset station are not sufficient
for good reception, this unit, using the AF data,
tunes in to another frequency broadcasting the
same programme as the original preset station is
broadcasting. (Programme search)
• The unit takes some time to tune in to another
station using programme search.
To activate programme search, follow the
procedure below.
• See also “Changing the general settings
(PSM)” on page 23.
1 Press and hold SEL (select) for more than
2 seconds so that one of the PSM items
2 Press ¢
or
4 to select
“P(Programme)-SEARCH.”
3 Turn the control dial clockwise to select “ON.”
Now programme search is activated.
4 Press SEL (select) to finish the setting.
To cancel programme search, repeat the same
procedure and select “OFF” in step 3 by turning
the control dial counterclockwise.
Setting the TA volume level
You can preset the volume level for TA Standby
Reception. When a traffic programme is received,
the volume level automatically changes to the
preset level.
2 Press ¢
or
4 to select “TA VOL”
(volume).
3 Turn the control dial to set to the desired
volume.
You can set it from “VOL 00” to “VOL 30” or
“VOL 50” (depending on the amplifier gain
control setting: see page 25).
Automatic clock adjustment
When shipped from the factory, the clock built in
this unit is set to be readjusted automatically
using the CT (Clock Time) data in the RDS
signal.
If you do not want to use automatic clock
adjustment, follow the procedure below.
2 Press ¢
or
4 to select “AUTO
ADJ” (adjustment).
3 Turn the control dial counterclockwise to select
“OFF.”
Now automatic clock adjustment is canceled.
To reactivate clock adjustment, repeat the
same procedure and select “ON” in step 3 by
turning the control dial clockwise.
Note:
You must stay tuned to the same station for more than
2 minutes after setting “AUTO ADJ” to “ON.”
Otherwise, the clock time will not be adjusted. (This is
because the unit takes up to 2 minutes to capture the
CT data in the RDS signal.)
NEWS:
AFFAIRS:
News
Topical programmes expanding
on current news or affairs
INFO:
Programmes which impart
advice on a wide variety of topics
SPORT:
Sport events
EDUCATE: Educational programmes
DRAMA:
Radio plays
CULTURE: Programmes on national or
regional culture
SCIENCE:
Programmes on natural science
and technology
VARIED:
Other programmes like comedies
or ceremonies
POP M:
Pop music
ROCK M:
Rock music
EASY M:
Easy-listening music
LIGHT M:
Light music
CLASSICS: Classical music
OTHER M:
Other music
WEATHER: Weather information
FINANCE:
Reports on commerce, trading,
the Stock Market, etc.
CHILDREN: Entertainment programmes for
children
SOCIAL:
Programmes on social
activities
RELIGION: Programmes dealing with any
aspect of belief or faith, or the
nature of existence or ethics
PHONE IN: Programmes where people can
express their views either by
phone or in a public forum
TRAVEL:
Programmes about travel
destinations, package tours,
and travel ideas and
opportunities
LEISURE:
Programmes concerned with
recreational activities such as
gardening, cooking, fishing,
etc.
JAZZ:
Jazz music
COUNTRY: Country music
NATION M: Current popular music from
another nation or region, in that
country’s language
OLDIES:
Classic pop music
FOLK M:
Folk music
DOCUMENT: Programmes dealing with
factual matters, presented in an
investigative style
ENGLISH
PTY codes
The same programme can be received on different frequencies.
Programme 1
broadcasting on
frequency A
Programme 1
broadcasting on
frequency E
Programme 1
broadcasting on
frequency B
Programme 1
broadcasting on
frequency C
Programme 1
broadcasting on
frequency D
17
ENGLISH
CD OPERATIONS
Playing a CD
1
The display changes to show the following:
Current source indication
Open the control panel.
CD indicator
When a CD is already in the loading slot,
pressing CD CD-CH turns on the unit and starts
playback automatically.
2
Total playing time Total track number
of the inserted disc of the inserted disc
Insert a CD into the loading slot.
The unit turns on,
draws the CD and
starts playback
automatically.
3
Current track
number
Close the control panel by hand.
All tracks will be played repeatedly until you
stop playback.
Notes:
• When a CD is inserted upside down, the CD
automatically ejects (if the control panel is open).
If the control panel is closed, the source changes to
the previously selected source, “PLEASE” and
“EJECT” appear alternately on the display.
• If there is no CD in the loading slot, you cannot
select CD as the source. “NO DISC” appears on
the display.
To go to a particular track directly
Press 0.
CD play stops and the control panel flips down.
The CD automatically ejects from the loading
slot. The source changes to the previously
selected source.
• If you change the source, CD play also stops
(without ejecting the CD).
Next time you select “CD” as the source, CD
play starts from where playback has been
stopped previously.
Press the number button corresponding to the
track number to start its playback.
Notes:
• If the ejected CD is not removed for about
15 seconds, the CD is automatically inserted again
into the loading slot to protect it from dust.
(CD play will not start this time.)
• You can eject the CD even when the unit is turned off.
Locating a track or a
particular portion on a CD
ENGLISH
To stop play and eject the CD
• To select a track number from 1 – 6:
Press 1 (7) – 6 (12) briefly.
• To select a track number from 7 – 12:
Press and hold 1 (7) – 6 (12) for more than one
second.
To go to a track quickly (+10 and –10
buttons)
1 Press MODE to enter the functions mode
while playing a CD.
To fast-forward or reverse the track
, while
Press and hold ¢
playing a CD, to fast-forward the
track.
Press and hold
reverse the track.
2 Press +10 or –10.
To skip 10 tracks* forwards to
the last track
4, while playing a CD, to
To go to the next or previous tracks
Press ¢
briefly, while
playing a CD, to go ahead to the
beginning of the next track.
Each time you press the button
consecutively, the beginning of
the next tracks is located and
played back.
To skip 10 tracks* backwards to
the first track
* First time you press +10 or –10 button, the
track skips to the nearest higher or lower
track with a track number of multiple ten (ex.
10th, 20th, 30th).
Then each time you press the button, you can
skip 10 tracks (see “How to use the +10 and
–10 buttons” on page 20).
• After the last track, the first track will be
selected, and vice versa.
4 briefly, while playing a CD, to go
Press
back to the beginning of the current track.
Each time you press the button consecutively,
the beginning of the previous tracks is located
and played back.
19
ENGLISH
How to use the +10 and –10 buttons
To play back tracks repeatedly
(Track Repeat Play)
• Ex. 1: To select track number 32 while
playing track number 6
You can play back the current track repeatedly.
1 Press MODE to enter the functions
mode while playing a CD.
Track 6
(Three times)
\ 10 \ 20 \ 30
2 Press RPT (repeat), while
(Twice)
\ 31 \ 32
display, so that “TRK RPT”
track repeat play mode turns on
and off alternately.
• Ex. 2 : To select track number 8 while
playing track number 36
(Three times)
Track 36 \ 30 \ 20 \ 10
(Twice)
\9\8
RPT indicator
Selecting CD playback modes
To play back tracks at random
(Disc Random Play)
You can play back all tracks on the CD at random.
mode while playing a CD.
2 Press RND (random), while
display, so that “DISC RND”
disc random play mode turns on
and off alternately.
RND and
When track repeat play is turned on, the RPT
indicator lights up on the display. The current
track starts playing repeatedly.
Prohibiting CD ejection
You can prohibit CD ejection and can lock a CD
in the loading slot.
While pressing CD CD-CH, press and hold
for more than 2 seconds.
“NO EJECT” flashes on the display for about
5 seconds, and the CD is locked and cannot be
ejected.
(disc) indicators
When disc random play is turned on, the RND
and
indicators light up on the display. A track
randomly selected starts playing.
To cancel the prohibition and unlock the
CD
While pressing CD CD-CH, press and hold
again for more than 2 seconds.
“EJECT OK” flashes on the display for about
5 seconds, and the CD is unlocked.
Selecting preset sound modes
(C-EQ: custom equalizer)
Indication pattern changes for each
sound mode except for “USER.”
You can select a preset sound mode (C-EQ:
custom equalizer) suitable to the music genre.
• There is a time limit in doing the following
procedure. If the setting is canceled before you
finish, start from step 1 again.
1
2
Press MODE to enter the functions
mode.
Press EQ (equalizer) while “MODE”
is still flashing on the display.
You can confirm the current
sound mode.
3
Select the sound mode you want.
button, the sound modes
change as follows:
USER
ROCK
JAZZ
HIP HOP
ENGLISH
SOUND ADJUSTMENTS
Ex.: When you select “ROCK”
Indication
For:
Preset values
BAS
TRE
LOUD
USER
(Flat sound)
00
00
OFF
ROCK
Rock or
disco music
+03
+01
ON
CLASSIC
Classical
music
+01
–02
OFF
POPS
Light music
+04
+01
OFF
HIP HOP
Funk or rap
music
+02
00
ON
JAZZ
Jazz music
+02
+03
OFF
Note:
You can adjust each sound mode to your preference.
Once you make an adjustment, it is automatically
stored for the currently selected sound mode. See
“Adjusting the sound” on page 22.
CLASSIC
POPS
USER
ROCK
JAZZ
CLASSIC
HIP HOP
POPS
21
ENGLISH
Adjusting the sound
*1 When you adjust the bass, treble, or loudness, the
You can adjust the sound characteristics to your
preference.
1
Select the item you want to adjust.
button, the adjustable items
change as follows:
BAS
TRE
(bass)
(treble)
(fader)
VOL
LOUD
BAL
(volume)
(loudness)
(balance)
Indication
To do:
FAD
2
Adjust the bass.
–06 (min.)
|
+06 (max.)
TRE*1
Adjust the treble.
–06 (min.)
|
+06 (max.)
FAD*2
Adjust the front
R06 (Rear only)
and rear speaker
|
balance.
F06 (Front only)
BAL
Adjust the left
L06 (Left only)
and right speaker
|
balance.
R06 (Right only)
LOUD*1
Boost low and
high frequencies
LOUD ON
to produce a well|
balanced sound
LOUD OFF
at low volume
level.
Adjust the volume. 00 (min.)
|
30 or 50 (max.)*4
Adjust the setting.
To increase the level or
turn on the loudness
To decrease the level or
turn off the loudness
Range
BAS*1
VOL*3
adjustment you have made is stored for the
currently selected sound mode (C-EQ) including
“USER.”
*2 If you are using a two-speaker system, set the fader
level to “00.”
*3 Normally the control dial works as the volume
control. So you do not have to select “VOL” to
adjust the volume level.
*4 Depending on the amplifier gain control setting.
(See page 25 for details.)
Indication pattern changes as
you adjust the bass or treble.
Ex. 1: When you adjust “TRE” (treble)
Ex. 2: When you turn on the loudness
3
Repeat steps 1 and 2 to adjust the
other items.
To reset each sound mode to the factory
settings, repeat the same procedure and
reassign the preset values listed in the table on
page 21.
OTHER MAIN FUNCTIONS
Adjust the PSM item selected.
ENGLISH
3
Changing the general settings
(PSM)
You can change the items listed in the table
below and on page 24 by using the PSM
(Preferred Setting Mode) control.
Basic Procedure
1
2
4
(See below and page 24.)
5
Repeat steps 2 and 3 to adjust the
other PSM items if necessary.
Finish the setting.
Select the PSM item you want to
adjust.
Preferred Setting Mode (PSM) items
• For detailed operations of each PSM items, refer to the pages listed in the table.
Indications
Selectable values/items
DEMO ON
Factory-preset See
settings
page
6
DEMO
Display demonstration
CLOCK H
Hour adjustment
CLOCK M
Minute adjustment
24H/12H
24/12-hour time display
12H
24H
24H
7
AUTO ADJ
Automatic clock setting
OFF
ON
ON
16
AF-REG
Alternative frequency/
Regionalization reception
AF
11, 12
DEMO OFF
DEMO ON
0 — 23 (1 — 12)
0 (0:00)
00 — 59
00 (0:00)
7
AF
AF REG
OFF*1
*1 Displayed only when the “DAB AF” is set to “OFF.”
23
ENGLISH
Indications
Selectable values/items
29 programme types
(see page 17)
PTY-STBY
PTY standby
TA VOL
Traffic announcement
volume
P-SEARCH
Programme search
DAB AF*3
Alternative frequency
search
DAB VOL*3
DAB volume adjustment
VOL –12 — VOL 12
LEVEL
Level display
OFF
DIMMER
Dimmer mode
OFF
VOL 00 — VOL 30 or 50*2
Telephone muting
OFF
13
VOL 20
16
OFF
ON
OFF
16
AF OFF
AF ON
AF ON
35
VOL 00
35
ON
25
AUTO
25
OFF
25
ON
AUTO
OFF
ON
TEL
Factory-preset See
settings
page
OFF
MUTING 1
MUTING 2
EXT IN*4
External component
CHANGER
LINE IN
CHANGER
25
AMP GAIN
Amplifier gain control
LOW PWR
HIGH PWR
HIGH PWR
25
*2 Depending on the amplifier gain control setting. (See page 25 for details.)
*3 Displayed only when the DAB tuner is connected.
*4 Displayed only when one of the following sources is selected—FM, AM, and CD.
You can activate or deactivate the level meter
according to your preference.
When shipped from the factory, level meter is
activated.
• ON:
• OFF:
Shows the audio level indicator.
Cancels the audio level indicator;
sound mode indicator is shown.
To select the external component to use
—EXT IN
You can connect the external component to the
CD changer jack on the rear using the Line Input
Adapter KS-U57 (not supplied).
To use the external component as the playback
source through this unit, you need to select
which component—CD changer or external
component—to use.
When shipped from the factory, CD changer is
selected as the external component.
ENGLISH
To select the level meter—LEVEL
To select the dimmer mode—DIMMER
When you turn on the car headlights, the display
automatically dims (Auto Dimmer).
When shipped from the factory, Auto Dimmer
mode is activated.
• AUTO:
• OFF:
• ON:
Activates Auto Dimmer.
Cancels Auto Dimmer.
Always dims the display.
Note:
Auto Dimmer equipped for this unit may not work
correctly on some vehicles, particularly on those
having a control dial for dimming.
In this case, set the dimmer mode to “ON” or “OFF.”
To select the telephone muting—TEL
This mode is used when a cellular phone system
is connected. Depending on the phone system
used, select either “MUTING 1” or “MUTING 2”
whichever mutes the sounds from this unit.
When shipped from the factory, this mode is
deactivated.
• MUTING 1: Select if this setting can mute the
sounds.
• MUTING 2: Select if this setting can mute the
sounds.
• OFF:
Cancels the telephone muting.
• CHANGER: To use the CD changer.
• LINE IN:
To use the external component
other than CD changer.
Note:
For connecting the Line Input Adapter KS-U57 and
the external component, refer to the Installation/
Connection Manual (separate volume).
To select the amplifier gain control
—AMP GAIN
You can change the maximum volume level of
this unit. When the maximum power of the
speakers is less than 50 W, select “LOW PWR”
to prevent them from being damaged.
When shipped from the factory, “HIGH PWR” is
selected.
• LOW PWR: You can adjust the volume level
from “VOL 00” to “VOL 30.”
Note:
If you can change the setting from
“HIGH PWR” to “LOW PWR” while
listening at a volume level more than
30, the unit automatically changes the
volume level to “VOL 30.”
• HIGH PWR: You can adjust the volume level
from “VOL 00” to “VOL 50.”
25
ENGLISH
Detaching the control panel
You can detach the control panel when leaving
the car.
When detaching or attaching the control panel,
be careful not to damage the connectors on the
back of the control panel and on the panel
holder.
Attaching the control panel
1
Insert the right side of the control
panel into the groove on the panel
holder.
Detaching the control panel
Before detaching the control panel, be sure to
turn off the power.
1
Unlock the control panel.
2
Pull the control panel out of the unit.
3
2
Put the detached control panel into
the provided case.
Press the left side of the control
panel to fix it to the panel holder.
Note on cleaning the connectors:
If you frequently detach the control panel, the
connectors will deteriorate.
To minimize this possibility, periodically wipe the
connectors with a cotton swab or cloth moistened
with alcohol, being careful not to damage the
connectors.
Connectors
ENGLISH
CD CHANGER OPERATIONS
We recommend that you use the JVC MP3compatible CD changer with your unit.
About MP3 discs
By using this CD changer, you can play back
your original CD-Rs (Recordable) and CD-RWs
(Rewritable) recorded either in audio CD format
or in MP3 format.
• You can also connect other CH-X series
CD changers (except CH-X99 and CH-X100).
However, they are not compatible with MP3
discs, so you cannot play back MP3 discs.
• You cannot use the KD-MK series CD
changers with this unit.
MP3 “files (tracks)” can be recorded in “folders”
—in PC terminology.
During recording, the files and folders can be
arranged in a way similar to arranging files and
folders of computer data.
“Root” is similar to the root of a tree. Every file
and folder can be linked to and be accessed from
the root.
Hierarchy
Level 1
Before operating your CD changer:
• Refer also to the Instructions supplied for
your CD changer.
• If no discs are in the magazine of the CD
changer or the discs are inserted upside
down, “NO DISC” will appear on the display.
If this happens, remove the magazine and
set the discs correctly.
• If no magazine is loaded in the CD changer,
“NO MAG” appears on the display. If this
happens, insert the magazine in the CD
changer.
• If “RESET 1” – “RESET 8” appears on the
display, something is wrong with the
connection between this unit and the CD
changer. If this happens, check the
connection and make sure the cords are
connected firmly. Then, press the reset
button of the CD changer.
Level 2
Level 3
Level 4
01
02
03
ROOT
05
01
1
6
3
4
10
5
1
11
2
12
Level 5
04
7
8
9
: Folders and their playback order
: MP3 files and their playback order
27
ENGLISH
Playing discs
Select the CD changer (CD-CH).
CD
• When the current disc is a CD:
Playback starts from the first track of the
current disc.
CD-CH*
* If you have changed “EXT IN” setting to “LINE IN”
(see page 25), you cannot select the CD changer.
Selected disc number
• When the current disc is an MP3 disc:
Playback starts from the first folder of the
current disc once file check is completed.
Selected disc
number
MP3 indicator
Current track
number
Total folder
number
Selected track number
Notes:
• When you press CD CD-CH, the power
automatically comes on. You do not have to press
to turn on the power.
• If you change the source, CD changer play also
stops. Next time you select the CD changer as the
source, CD changer play starts from where
playback has been stopped previously.
To go to a particular disc directly
Press the number button corresponding to the
disc number to start its playback (while the CD
changer is playing).
• To select a disc number from 1 – 6:
Press 1 (7) – 6 (12) briefly.
• To select a disc number from 7 – 12:
Press and hold 1 (7) – 6 (12) for more than
one second.
Press and hold ¢
, during
play, to fast-forward the track/file.
Press and hold
the track/file.
4, during play, to reverse
Note:
During this operation, you can only hear intermittent
sounds. (The elapsed playing time also changes
intermittently on the display.)
To go to the next or previous tracks/files
Press ¢
briefly during play,
to skip ahead to the beginning of
the next track/file.
consecutively, the beginning of
the next tracks/files is located
and played back.
Press
4 briefly during play, to skip back to
the beginning of the current track/file.
the beginning of the previous tracks/files is
located and played back.
This operation is only possible when
using JVC MP3-compatible CD changer
(CH-X1500).
To go to a track/file quickly (+10 and –10
buttons)
* First time you press +10 or –10 button, the
track/file skips to the nearest higher or lower
track/file with a track/file number of multiple
ten (ex. 10th, 20th, 30th).
Then each time you press the button, you can
skip 10 tracks/files (see “How to use the +10
and –10 buttons” below).
• After the last track/file, the first track/file will
be selected, and vice versa.
Note:
If the current playing disc is an MP3 disc, files are
skipped within the same folder.
How to use the +10 and –10 buttons
• Ex. 1: To select track/file number 32 while
playing track/file number 6
(Three times)
(Twice)
Track/File 6 \ 10 \ 20 \ 30 \ 31 \ 32
• Ex. 2 : To select track/file number 8 while
playing track/file number 36
(Twice)
(Three times)
Track/File 36 \ 30 \ 20 \ 10 \ 9 \ 8
To skip to the next or previous folder
(only for MP3 discs)
1 Press MODE to enter the functions mode
Press 5 (up) while playing an MP3
disc, to go to the next folder.
consecutively, the next folder is
located, and the first file in the
folder starts playback.
while playing a disc.
2 Press +10 or –10.
To skip 10 tracks/files*
forwards to the last track/file
To skip 10 tracks/files*
backwards to the first track/file
ENGLISH
To fast-forward or reverse the track/file
Press ∞ (down) while playing an MP3 disc, to go
to the previous folder.
the previous folder is located, and the first file in
the folder starts playback.
29
ENGLISH
Selecting the playback modes
To play back tracks/files repeatedly
(Track Repeat/Disc Repeat Play)
To play back tracks/files at random
(Disc Random/Magazine Random Play)
mode during play.
mode during play.
2 Press RPT (repeat), while
display.
Each time you press the button, the
repeat play mode changes as
follows:
2 Press RND (random), while
display.
Each time you press the button, the
random play mode changes as
follows:
DISC RND
TRK RPT
DISC RPT
Canceled
MAG RND
Canceled
RPT indicator
Ex.: When you select “TRK RPT”
RND and
(disc) indicators
Ex.: When you select “DISC RND”
Note:
MP3 indicator also lights up if the current playing disc
is an MP3 disc.
Mode
DISC RND
MAG RND
Active
indicator
RND and
indicators
light up.
Plays at random
All tracks/files of
the current (or
specified) disc.
Note:
MP3 indicator also lights up if the current playing disc
is an MP3 disc.
Mode
Active
indicator
Plays repeatedly
TRK RPT
RPT indicator
lights up.
DISC RPT
and RPT All tracks/files of
indicators light the current (or
up.
specified) disc.
RND indicator All tracks/files of
lights up.
the inserted discs.
The current (or
specified) track/
file.
ENGLISH
EXTERNAL COMPONENT OPERATIONS
Playing an external component 2
You can connect the external components to the
CD changer jack on the rear using the Line Input
Adapter KS-U57 (not supplied).
Preparations:
• For connecting the Line Input Adapter KS-U57 and
the external component, refer to the Installation/
Connection Manual (separate volume).
• Before operating the external component using the
following procedure, select the external input
correctly. (See “To select the external component to
use—EXT IN” on page 25.)
1
3
4
Turn on the connected component
and start playing the source.
Adjust the volume.
Adjust the sound as you want. (See
pages 21 and 22.)
Select the external component
(LINE IN).
CD
LINE IN*
• If “LINE IN”* does not appear on the display,
see page 25 and select the external input
(“LINE IN”).
* Displayed only when one of the following sources is
selected—FM, AM, and CD.
When you press CD CD-CH, the power automatically
comes on. You do not have to press
to turn
on the power.
31
ENGLISH
DAB TUNER OPERATIONS
We recommend that you use DAB (Digital Audio
Broadcasting) tuner KT-DB1500 or KT-DB1000
with your unit.
If you have another DAB tuner, consult your JVC
IN-CAR ENTERTAINMENT dealer.
• Refer also to the Instructions supplied for your
DAB tuner.
What is DAB system?
DAB is one of the digital radio broadcasting
systems available today. It can deliver CD
quality sound without any annoying
interference and signal distortion.
Furthermore, it can carry text, pictures, and
data.
In contrast to FM broadcast, where each
programme is transmitted on its own
frequency, DAB combines several
programmes (called “services”) to form one
“ensemble.”
In addition, each “service”—called “primary
service”—can also be divided into its
components (called “secondary service”).
Tuning in to an ensemble and
one of the services
A typical ensemble has 6 or more programmes
(services) broadcast at the same time. After
tuning in to an ensemble, you can select a
service you want to listen to.
Before you start....
Press FM/AM DAB briefly if CD, CD changer, or
external component is the current source.
1
Select the DAB tuner.
Each time you press and
hold the button, the DAB
tuner and the FM/AM tuner
are alternately selected.
DAB
2
With the DAB tuner connected with this unit,
you can enjoy these DAB services.
Note:
When reception switches between DAB and FM, the
listening volume level may increase or decrease
inconveniently. This change in the volume level results
from unequal audio injection levels at broadcaster
site, but not from the malfunction of this unit.
To prevent this inconvenience, you can adjust the DAB
volume level. (See “To adjust the DAB volume level”
on page 35.)
FM/AM
Select the DAB band (DAB1, DAB2,
or DAB3) you want.
button, the DAB band
changes as follows:
DAB1
DAB2
DAB3
Note:
This receiver has three DAB bands (DAB1,
DAB2, DAB3). You can use any of them to tune
in to an ensemble.
Start searching for an ensemble.
To search for ensembles of
higher frequency
To search for ensembles of lower frequency
To tune in to a particular ensemble
without searching
ENGLISH
3
1 Press and hold FM/AM DAB to select DAB
tuner as the source.
When an ensemble is received, searching
stops.
To stop searching before an ensemble is
received, press the same button you have
pressed for searching.
4
Select a service (either primary or
secondary) you want to listen to.
To select the next service (If a
primary service has some
secondary services, they are
selected before the next
primary service is selected.)
To select the previous service (either
primary or secondary)
To change the display information while
tuning in to an ensemble
Normally service name is shown on the display.
If you want to check the ensemble name or its
frequency, press DISP (display) repeatedly.
the following information appears
for a while on the display.
2 Press FM/AM DAB repeatedly to select the
DAB band (DAB1, DAB2, or DAB3).
or
4 for more
than one second.
4 Press ¢
or
4 repeatedly until the
ensemble you want is reached.
• If you hold down the button, the frequency
keeps changing until you release the
button.
5 Press 5 (up) or ∞ (down) to select a service
(either primary or secondary) you want to
listen to.
3 Press and hold ¢
To restore the FM/AM tuner
Press and hold FM/AM DAB again.
Storing DAB services in
memory
You can preset up to 6 DAB services in each
DAB band (DAB1, DAB2, and DAB3) manually.
1
Service name
Ensemble name
DAB
Channel number
2
Frequency
FM/AM
or DAB3) you want.
changes as follows:
Clock
DAB1
DAB2
DAB3
33
ENGLISH
3
4
Tune in to an ensemble you want.
Select a service of the ensemble you
want to listen to.
To select the next service
To select the previous service
5
(in this example, 1) for more than
2 seconds to store the selected
service into the preset number you
want.
Tuning in to a preset DAB
service
You can easily tune in to a preset DAB service.
Remember that you must store services first. If
you have not stored them yet, see “Storing DAB
services in memory” on pages 33 and 34.
1
DAB
2
FM/AM
or DAB3) you want.
changes as follows:
Selected preset number
DAB1
3
6
DAB2
DAB3
Select the number (1 – 6) for the
preset DAB service (primary) you
want.
Repeat the above procedure to store
other DAB services into other preset
numbers.
Notes:
• You can only preset primary DAB services. If you
store a secondary service, its primary service will
be stored instead.
• A previously preset DAB service is erased when a
new DAB service is stored in the same preset
number.
• Preset DAB services are erased when the power
supply to the memory circuit is interrupted (for
example, during battery replacement). If this
occurs, preset the DAB services again.
Note:
If the selected primary service has some secondary
services, pressing the same number button repeatedly
will tune in to the secondary services.
Tracing the same programme automatically
(Alternative Reception)
You can keep listening to the same programme.
• While receiving a DAB service:
When driving in an area where a service
cannot be received, this unit automatically
tunes in to another ensemble or FM RDS
station, broadcasting the same programme.
• While receiving an FM RDS station:
When driving in an area where a DAB service
is broadcasting the same programme as the
FM RDS station is broadcasting, this unit
automatically tunes in to the DAB service.
To use Alternative Reception
To adjust the DAB volume level
You can adjust the volume level of DAB tuner
and store it in memory. By adjusting the volume
level properly to match it to the FM sound level,
you will not need to adjust the volume level each
time you change the source.
When shipped from the factory, DAB volume
level is set at “00.”
ENGLISH
What you can do more with
DAB
2 Press ¢
or
4 to select “DAB VOL”
(volume).
3 Turn the control dial to set to the desired
volume.
You can set it from “VOL –12” to “VOL 12.”
When shipped from the factory, Alternative
2 Press ¢
or
4 to select “DAB AF”
(alternative frequency).
3 Turn the control dial to select the desired
mode.
• AF ON: Traces the programme among
DAB services and FM RDS
stations—Alternative Reception.
The AF indicator lights up on the
display (see page 11).
• AF OFF: Alternative Reception is
deactivated.
Note:
When Alternative Reception (for DAB services) is
activated, Network-Tracking Reception (for RDS
stations: see page 11) is also activated automatically.
On the other hand, Network-Tracking Reception
cannot be deactivated without deactivating
Alternative Reception.
35
ENGLISH
USING THE REMOTE CONTROLLER
This unit can be remotely controlled as instructed
here (with an optionally purchased remote
controller). We recommend that you use remote
controller RM-RK50 or RM-RK60 with your unit.
(Ex.: When you are using RM-RK60)
3. Return the battery holder.
Insert again the battery holder by pushing it
until you hear a clicking sound.
(back side)
Before using the remote controller:
• Aim the remote controller directly at the remote
sensor on the main unit. Make sure there is no
obstacle in between.
Remote sensor
• Do not expose the remote sensor to strong
light (direct sunlight or artificial lighting).
Installing the battery
When the controllable range or effectiveness
of the remote controller decreases, replace
the battery.
1. Remove the battery holder.
1) Push out the battery holder in the
direction indicated by the arrow using a
ball point pen or a similar tool.
2) Remove the battery holder.
(back side)
2. Place the battery.
Slide the battery into the holder with the
+ side facing upwards so that the battery
is fixed in the holder.
Lithium coin
battery (product
number: CR2025)
WARNING:
• Store the battery in a place where children
cannot reach.
If a child accidentally swallows the battery,
consult a doctor immediately.
• Do not recharge, short, disassemble, or heat the
battery or dispose of it in a fire.
Doing any of these things may cause the battery
to give off heat, crack, or start a fire.
• Do not leave the battery with other metallic
materials.
Doing this may cause the battery to give off
heat, crack, or start a fire.
• When throwing away or saving the battery,
wrap it in tape and insulate; otherwise, the
battery may start to give off heat, crack, or start
a fire.
• Do not poke the battery with tweezers or similar
tools.
Doing this may cause the battery to give off
heat, crack, or start a fire.
CAUTION:
DO NOT leave the remote controller in a place
(such as dashboards) exposed to direct sunlight for
a long time. Otherwise, it may be damaged.
KD-G302 and KD-G301 are equipped with the
steering wheel remote control function.
If your car is equipped with the steering wheel
remote controller, you can operate the unit
using the controller.
• See the Installation/Connection Manual
(separate volume) for connection to utilize
this function.
RM-RK60
3 • Selects the preset stations (or services)
while listening to the radio (or the DAB
tuner).
Each time you press the button, the preset
station (or service) number increases, and
the selected station (or service) is tuned in.
• While playing an MP3 disc on an MP3compatible CD changer;
– Skips to the previous disc if pressed
briefly.
– Skips to the previous folder if pressed
and held.
Note: While playing a CD on a CD changer,
this always skips to the previous disc.
ENGLISH
Location of the buttons
S
4 Selects the sound mode (C-EQ: custom
equalizer).
Each time you press the button, the sound
mode (C-EQ) changes.
1 • Turns on the unit if pressed when the unit
is turned off.
• Turns off the unit if pressed and held until
“SEE YOU” appears on the display.
• Drops the volume level in a moment if
pressed briefly.
Press again to resume the volume.
2 • Searches for stations while listening to the
radio.
• Selects services while listening to the DAB
tuner if pressed briefly.
• Searches for ensembles while listening to
the DAB tuner if pressed for more than one
second.
• Fast-forwards or reverses the track/file if
pressed and held while listening to a disc.
• Skips to the beginning of the next track/file
or goes back to the beginning of the
current (or previous) tracks/files if pressed
briefly while listening to a disc.
5 • Selects the band while listening to the
radio (or the DAB tuner).
Each time you press the button, the band
changes.
• While playing an MP3 disc on an MP3compatible CD changer;
– Skips to the next disc if pressed briefly.
– Skips to the next folder if pressed and
held.
Note: While playing a CD on a CD changer,
this always skips to the next disc.
6 Selects the source.
Each time you press the button, the source
changes.
7 Functions the same as the control dial on the
main unit.
Note: These buttons do not function for the
Preferred Setting Mode adjustment.
37
What appears to be trouble is not always serious. Check the following points before calling a service
center.
Symptoms
• Sound cannot be heard
from the speakers.
CD Playback
FM/AM
General
ENGLISH
TROUBLESHOOTING
Causes
Remedies
The volume level is set to the
minimum level.
Adjust it to the optimum level.
Connections are incorrect.
Check the cords and
connections.
• This unit does not work
at all.
The built-in microcomputer may
have functioned incorrectly due
to noise, etc.
Press the reset button on the
panel holder after detaching the
control panel. (The clock setting
and preset stations stored in
memory are erased.)
(See page 2.)
• SSM (Strong-station
Sequential Memory)
automatic preset does
not work.
Signals are too weak.
Store stations manually.
• Static noise while
listening to the radio.
The aerial is not connected
firmly.
Connect the aerial firmly.
• CD cannot be played
back.
CD is inserted upside down.
Insert the CD correctly.
• CD-R/CD-RW cannot be
played back.
• Tracks on the CD-R/
CD-RW cannot be
skipped.
CD-R/CD-RW is not finalized.
• Insert a finalized CD-R/
CD-RW.
• Finalize the CD-R/CD-RW
with the component which
you used for recording.
• CD cannot be ejected.
CD is locked.
Unlock the CD.
(See page 20.)
• CD sound is sometimes
interrupted.
You are driving on rough roads.
Stop playback while driving on
rough roads.
CD is scratched.
Change the CD.
Connections are incorrect.
Check the cords and
connections.
No CD in the loading slot.
Insert a CD into the loading slot.
CD is inserted incorrectly.
Insert the CD correctly.
• “NO DISC” appears on
the display.
Remedies
No disc is in the magazine.
Insert discs into the
magazine.
Discs are inserted upside down.
Insert discs correctly.
The current disc does not
contain any MP3 files.
Insert a disc that contains
MP3 files.
• “NO MAG” appears on the
display.
No magazine is loaded in the
CD changer.
Insert the magazine.
• “RESET 8” appears on the
display.
This unit is not connected to the
CD changer correctly.
Connect this unit and the
CD changer correctly and
press the reset button of the
CD changer.
• “RESET 1” – “RESET 7”
• The CD changer does not
work at all.
ENGLISH
• “NO DISC” appears on the
display.
Causes
CD Changer
Symptoms
Press the reset button of the
CD changer.
The built-in microcomputer may
function incorrectly due to
noise, etc.
Press the reset button on the
panel holder after detaching
the control panel. (The clock
setting and preset stations
stored in memory are
erased.) (See page 2.)
About mistracking:
Mistracking may result from driving on extremely rough roads. This does not damage the unit and the disc,
but will be annoying.
We recommend that you stop disc play while driving on such rough roads.
39
ENGLISH
MAINTENANCE
Handling discs
When playing a CD-R or CD-RW
This unit has been designed to reproduce CDs,
CD-Rs (Recordable), and CD-RWs (Rewritable).
• This unit is not compatible with MP3 discs,
but can operate a JVC MP3-compatible
CD changer.
How to handle discs
When removing a disc
Center holder
from its case, press down
the center holder of the case
and lift the disc out, holding
it by the edges.
• Always hold the disc by the edges. Do not
touch its recording surface.
When storing a disc into its case, gently insert
the disc around the center holder (with the
printed surface facing up).
• Make sure to store discs into the cases after
use.
To keep discs clean
A dirty disc may not be played
correctly. If a disc does become
dirty, wipe it with a soft cloth in a
straight line from center to edge.
To play new discs
New discs may have some rough
spots around the inner and outer
edges. If such a disc is used, this
unit may reject the disc.
To remove these rough spots, rub
the edges with a pencil or ball-point pen, etc.
Before playing back CD-Rs or CD-RWs, read
their instructions or cautions carefully.
• Use only “finalized” CD-Rs or CD-RWs.
• Some CD-Rs or CD-RWs may not be played
back on this unit because of their disc
characteristics, and for the following reasons:
– Discs are dirty or scratched.
– Moisture condensation on the lens inside the
unit.
– The pickup lens inside the unit is dirty.
• CD-RWs may require a longer readout time
since the reflectance of CD-RWs is lower than
that of regular CDs.
• CD-Rs or CD-RWs are susceptible to high
temperatures or high humidity, so do not leave
them inside your car.
• Do not use following CD-Rs or CD-RWs:
– Discs with stickers, labels, or protective seal
stuck to the surface.
– Discs on which labels can be directly printed
by an ink jet printer.
Using these discs under high temperatures or
high humidity may cause malfunctions or
damage to discs. For example,
– Stickers or labels may shrink and warp a
disc.
– Stickers or labels may be peeled off so discs
cannot be ejected.
– Print on discs may get sticky.
Read instructions or cautions about labels and
printable discs carefully.
Moisture condensation
Moisture may condense on the lens inside the
CD player in the following cases:
• After starting the heater in the car.
• If it becomes very humid inside the car.
Should this occur, the CD player may
malfunction. In this case, eject the disc and leave
the unit turned on for a few hours until the
moisture evaporates.
Warped
disc
Sticker
CAUTIONS:
• Do not insert 8 cm discs (single CDs) into the
loading slot. (Such discs cannot be ejected.)
• Do not insert any disc of unusual shape—like a
heart or flower; otherwise, it will cause a
malfunction.
• Do not expose discs to direct sunlight or any
heat source or place them in a place subject to
high temperature and humidity. Do not leave
them in a car.
• Do not use any solvent (for example,
conventional record cleaner, spray, thinner,
benzine, etc.) to clean discs.
Sticker
residue
Disc
Stick-on
label
AUDIO AMPLIFIER SECTION
CD PLAYER SECTION
Maximum Power Output:
Front:
50 W per channel
Rear:
50 W per channel
Continuous Power Output (RMS):
Front:
19 W per channel into 4 Ω, 40 Hz
to 20 000 Hz at no more than
0.8% total harmonic distortion.
Rear:
19 W per channel into 4 Ω, 40 Hz
to 20 000 Hz at no more than
0.8% total harmonic distortion.
Load Impedance: 4 Ω (4 Ω to 8 Ω allowance)
Tone Control Range:
Bass:
±10 dB at 100 Hz
Treble: ±10 dB at 10 kHz
Frequency Response: 40 Hz to 20 000 Hz
Signal-to-Noise Ratio: 70 dB
Line-Out Level/Impedance:
2.0 V/20 kΩ load (full scale)
Output Impedance: 1 kΩ
Type: Compact disc player
Signal Detection System: Non-contact optical
pickup (semiconductor laser)
Number of channels: 2 channels (stereo)
Dynamic Range:
96 dB
Signal-to-Noise Ratio: 98 dB
Wow and Flutter: Less than measurable limit
TUNER SECTION
Frequency Range:
FM:
87.5 MHz to 108.0 MHz
AM:
(MW) 522 kHz to 1 620 kHz
(LW) 144 kHz to 279 kHz
ENGLISH
SPECIFICATIONS
GENERAL
Power Requirement:
Operating Voltage:
DC 14.4 V (11 V to 16 V allowance)
Grounding System: Negative ground
Allowable Operating Temperature: 0°C to +40°C
Dimensions (W × H × D):
Installation Size (approx.):
182 mm × 52 mm × 150 mm
Panel Size (approx.):
188 mm × 58 mm × 12 mm
Mass (approx.):
1.4 kg (excluding accessories)
Design and specifications are subject to change
without notice.
[FM Tuner]
Usable Sensitivity:
11.3 dBf (1.0 µV/75 Ω)
50 dB Quieting Sensitivity:
16.3 dBf (1.8 µV/75 Ω)
Alternate Channel Selectivity (400 kHz):
65 dB
Stereo Separation: 30 dB
Capture Ratio: 1.5 dB
[MW Tuner]
Sensitivity: 20 µV
Selectivity: 35 dB
[LW Tuner]
Sensitivity: 50 µV
41
Having TROUBLE with operation?
Please reset your unit
Refer to page of How to reset your unit
Haben Sie PROBLEME mit dem Betrieb?
Bitte setzen Sie Ihr Gerät zurück
Siehe Seite Zurücksetzen des Geräts
Vous avez des PROBLÈMES de fonctionnement?
Réinitialisez votre appareil
Référez-vous à la page intitulée Comment réinitialiser votre appareil
Hebt u PROBLEMEN met de bediening?
Stel het apparaat terug
Zie de pagina met de paragraaf Het apparaat terugstellen
EN, GE, FR, NL
© 2003 VICTOR COMPANY OF JAPAN, LIMITED
1203KKSMDTJEIN
KD-G302/KD-G301
GET0187-005A
[E/EX]
Installation/Connection Manual
Einbau/Anschlußanleitung
Manuel d’installation/raccordement
Handleiding voor installatie/aansluiting
ENGLISH
1203KKSMDTJEIN
EN, GE, FR, NL
DEUTSCH
This unit is designed to operate on 12 V DC,
NEGATIVE ground electrical systems. If your
vehicle does not have this system, a voltage
inverter is required, which can be purchased at
JVC IN-CAR ENTERTAINMENT dealers.
FRANÇAIS
Dieses Gerät ist für einen Betrieb in
elektrischen Anlagen mit 12 V Gleichstrom
und (–) Erdung ausgelegt. Verfügt Ihr
Fahrzeug nicht über diese Anlage, ist ein
Spannungsinverter erforderlich, der bei JVC
Autoradiohändler erworben werden kann.
NEDERLANDS
Cet appareil est conçu pour fonctionner sur des
sources de courant continu de 12 V à masse
NEGATIVE. Si votre véhicule n’offre pas ce type
d’alimentation, il vous faut un convertisseur de
tension, que vous pouvez acheter chez un
revendeur d’autoradios JVC.
Dit apparaat mag worden gebruikt bij elektrische
systemen die werken op 12 V gelijkstroom met
negatieve aarding. Als uw auto niet is uitgerust
met een dergelijk systeem, is een spanningsomzetter
vereist. Dit instrument kan worden aangeschaft bij
JVC car audio dealers.
Parts list for installation and
connection
Teileliste für den Einbau und Anschluß Liste des pièces pour l’installation et
Die folgenden Teile werden zusammen mit
raccordement
Lijst van onderdelen die u bij
installatie en aansluiting nodig hebt
The following parts are provided for this unit.
After checking them, please set them correctly.
diesem Gerät geliefert.
De volgende onderdelen worden bij het apparaat
Les pièces suivantes sont fournies avec cet
Nach ihrer Überprüfung, die Teile richtig einsetzen. appareil.
geleverd.
Après vérification, veuillez les placer correctement. Installeer ze op de juiste wijze, nadat u ze hebt
gecontroleerd.
A/B
Hard case/Control panel
Etui/Schalttafel
Etui de transport/Panneau
de commande
Behuizing/Bedieningspaneel
F
Washer (ø5)
Unterlegscheibe (ø5)
Rondelle (ø5)
Sluitring (ø5)
G
Lock nut (M5)
Sicherungsmutter (M5)
Ecrou d’arrêt (M5)
Contra-moer (M5)
E
Power cord
Stromkable
Cordon d’alimentation
Stroomkabel
D
Trim plate
Frontrahmen
Plaque d’assemblage
Sierplaat
C
Sleeve
Halterung
Manchon
Huis
H
Mounting bolt (M5 x 20 mm)
Befestigungsschraube (M5 x 20 mm)
Boulon de montage (M5 x 20 mm)
Bevestigingsbout (M5 x 20 mm)
I
Rubber cushion
Gummipuffer
Amortisseur en caoutchouc
Rubberdop
J
Handles
Griffe
Poignées
Hendels
INSTALLATION
(IN-DASH MOUNTING)
EINBAU
(IM ARMATURENBRETT)
INSTALLATION (MONTAGE
INSTALLATIE (INBOUW IN
DANS LE TABLEAU DE BORD) HET DASHBOARD)
The following illustration shows a typical
installation. If you have any questions or require
information regarding installation kits, consult
your JVC IN-CAR ENTERTAINMENT dealer or
a company supplying kits.
• If you are not sure how to install this unit
correctly, have it installed by a qualified
technician.
Die folgende Abbildung zeigt einen typischen
Einbau. Bei irgendwelchen Fragen oder wenn
Sie Informationen hinsichtlich des Einbausatzes
brauchen, wenden Sie sich an ihren JVC
Autoradiohändler oder ein Unternehmen das
diese Einbausätze vertreibt.
• Sind Sie sich über den richtigen Einbau des
Geräts nicht sicher, lassen Sie es von einem
qualifizierten Techniker einbauen.
L’illustration suivante est un exemple
d’installation typique. Si vous avez des
questions ou avez besoin d’information sur des
kits d’installation, consulter votre revendeur
d’autoradios JVC ou une compagnie
d’approvisionnement.
• Si l’on n’est pas sûr de pouvoir installer
correctement cet appareil, le faire installer par
un technicien qualifié.
4
2
1
B
Op de volgende afbeelding kunt u zien hoe de
installatie, normaal gesproken, in zijn werk gaat.
Neem bij vragen of voor meer bijzonderheden over
inbouwpakketten contact op met uw JVC car audio
dealer of een dealer of een bedrijf dat
inbouwpakketten levert.
• Als u niet zeker weet hoe u dit apparaat moet
installeren, kunt u dit beter door een daartoe
gekwalificeerde technicus laten doen.
!
Do the required electrical connections.
Nehmen Sie die erforderlichen
elektrischen Anschlüsse vor.
Réalisez les connexions électriques.
Breng de vereiste elektrische verbindingen
tot stand.
D
I
C
3
J
C
4
m
m
53
~
@
¤
D
B
m
m
Ÿ
H
⁄
*1 When you stand the unit, be careful
not to damage the fuse on the rear.
*1 Beim Aufstellen des Geräts darauf
achten, daß die Sicherung auf der
Rückseite nicht beschädigt wird.
*1 Lorsque vous mettez l’appareil à la
verticale, faire attention de ne pas
endommager le fusible situé sur
l’arrière.
*1 Wanneer u het apparaat rechtop zet,
moet u erop letten dat u de zekering
aan de achterkant niet beschadigt.
*1
18
Bend the appropriate tabs to hold the
sleeve firmly in place.
Die geeigneten Zapfen biegen, um
die Manschette sicher festzuhalten.
Tordez les languettes appropriées
pour maintenir le manchon en place.
Buig de vereiste lipjes zodat de huls goed
op zijn plaats wordt gehouden.
Removing the unit
Ausbau des Geräts
Retrait de l’appareil
Verwijderen van het apparaat
Before removing the unit, release the rear
section.
Vor dem Ausbau des Geräts den hinteren Teil
freigeben.
Avant de retirer l’appareil, libérer la section
arrière.
Voordat u het apparaat verwijdert, moet u het
achtergedeelte losmaken.
1
2
B
3
D
Insert the two handles, then pull them as illustrated so that
the unit can be removed.
Die beiden Handgriffe einsetzen und dann ziehen wie in der
Abbildung gezeigt, so daß das Gerät entfernt werden kann.
Insérez les deux poignées, puis tirez de la façon illustrée de
façon à retirer l’appareil.
Plaats de twee hendels en trek ze vervolgens zoals afgebeeld naar
voren zodat het toestel kan worden verwijderd.
1
J
When using the optional stay / Beim Verwenden der AnkerOption / Lors de l’utilisation du hauban en option / Wanneer u
de steun gebruikt (facultatief)
Stay (option)
Anker (Option)
Hauban (en option)
Steun (facultatief)
Fire wall
Feuerwand
Cloison
Brandscherm
F
Dashboard
Armaturenbrett
Tableau de bord
Dashboard
G
H
When installing the unit without using the sleeve / Beim Einbau des Geräts ohne
Halterung / Lors de l’installation de l’appareil scans utiliser de manchon / Wanneer
u het apparaat zonder huis installeert
In a Toyota for example, first remove the car radio and install the unit in its place.
Zum Beispiel in einem Toyota zuerst das Autoradio ausbauen und dann das Gerät an seinem Platz einbauen.
Par exemple dans une Toyota, retirer d’abord l’autoradio et installer l’appareil à la place.
Voorbeeld: Bij een Toyota moet u eerst de autoradio verwijderen en daarna het apparaat installeren.
Flat type screws (M5 x 8 mm)*
Senkkopfschrauben (M5 x 8 mm)*
Vis à tête plate (M5 x 8 mm) *
Platkopschroeven (M5 x 8 mm)*
* Not included with this unit.
* Nicht Teil dieses Geräts.
* Non fourni avec cet appareil.
* Niet meegeleverd.
Bracket*
Konsole*
Support *
Console*
Screw (option)
Schraube (Option)
Vis (en option)
Schroef (facultatief)
C
Pocket
Taschen
Poche
Zak
Flat type screws (M5 x 8 mm)*
Senkkopfschrauben (M5 x 8 mm)*
Vis à tête plate (M5 x 8 mm) *
Platkopschroeven (M5 x 8 mm)*
Bracket*
Konsole*
Support *
Console*
Note
Install the unit at an angle of less than 30˚.
Stellen Sie das Gerät mit einem Winkel von
weniger als 30˚ auf.
Installez l’appareil avec un angle de moins de 30˚.
Installeer het toestel met een hoek kleiner dan 30˚.
: When installing the unit on the mounting bracket, make sure to use the 8 mm-long screws. If
longer screws are used, they could damage the unit.
Hinweis
: Beim Anbringen des Gerät an der Konsole sicherstellen, daß 8 mm lange Schrauben verwendet
werden. Werden längere Schrauben verwendet, können sie das Gerät beschädigen.
Remarque : Lors de l’installation de l’appareil sur le support de montage, s’assurer d’utiliser des vis d’une
longueur de 8 mm. Si des vis plus longues sont utilisées, elles peuvent endommager l’appareil.
Opmerking : Wanneer u het apparaat aan de bevestigingsklem vastmaakt, moet u de 8 mm lange schroeven gebruiken. Als
u langere schroeven gebruikt, kan het apparaat worden beschadigd.
ELECTRICAL CONNECTIONS
ELEKTRISCHE ANSCHLÜSSE
RACCORDEMENTS ELECTRIQUES ELEKTRISCHE VERBINDINGEN
To prevent short circuits, we recommend that
you disconnect the battery’s negative terminal
and make all electrical connections before
installing the unit.
• Be sure to ground this unit to the car’s
chassis again after installation.
Zur Vermeidung von Kurzschlüssen empfehlen
wir, daß Sie den negativen Batterieanschluß
abtrennen und alle elektrischen Anschlüsse
herstellen, bevor das Gerät eingebaut wird.
• Sicherstellen, daß das Gerät nach dem
Einbau a Chassis des Fahrzeugs geerdet
wird.
Pour éviter tout court-circuit, nous vous
recommandons de débrancher la borne
négative de la batterie et d’effectuer tous les
raccordements électriques avant d’installer
l’appareil.
• Assurez-vous de raccorder de nouveau la
mise à la masse de cet appareil au châssis
de la voiture après l’installation.
Notes:
• Replace the fuse with one of the specified
rating. If the fuse blows frequently, consult your
JVC IN-CAR ENTERTAINMENT dealer.
• It is recommended to connect to the speakers
with maximum power of more than 50 W (both
at the rear and at the front, with an impedance
of 4 Ω to 8 Ω). If the maximum power is less
than 50 W, change “AMP GAIN” setting to
prevent the speakers from being damaged
(see page 25 of the INSTRUCTIONS).
• To prevent short-circuit, cover the terminals of
the UNUSED leads with insulating tape.
• The heat sink becomes very hot after use. Be
careful not to touch it when removing this unit.
Heat sink
Abstrahlblech
Dissipateur de chaleur
Warmte-opnemer
PRECAUTIONS on power supply
and speaker connections:
• DO NOT connect the speaker leads of the
power cord to the car battery; otherwise,
the unit will be seriously damaged.
• BEFORE connecting the speaker leads of the
power cord to the speakers, check the
speaker wiring in your car.
+
L -
-
+
R -
-
Hinweise:
• Die Sicherung mit einer der entsprechenden
Nennleistung ersetzen. Brennt die Sicherung
häufig durch, wenden Sie sich an ihren JVC
Autoradiohändler.
• Es wird empfohlen, Lautsprecher mit einer
Maximalleistung von mehr als 50 W
anzuschließen (sowohl hinten als auch vorne,
mit einer Impedanz von 4 Ω bis 8 Ω). Wenn
die Maximalleistung weniger als 50 W beträgt,
stellen Sie „AMP GAIN“ anders ein, um
Schäden an den Lautsprechern zu vermeiden
(siehe Seite 25 der BEDIENUNGSANLEITUNG).
• Zur Vermeidung eines Kurzschlusses die
Anschlußklemmen der NICHT VERWENDETEN
Leitungen mit Isolierklebeband umwickeln.
• Das Abstrahlblech wird nach dem Gebrauch
sehr heiß. Beim Ausbau des Geräts darauf
achten, das Abstrahlblech nicht zu berühren.
Remarques:
• Remplacer le fusible par un de la valeur
précisée. Si le fusible saute souvent, consulter
votre revendeur d’autoradios JVC.
• Il est recommandé de connecter des
enceintes avec une puissance de plus de
50 W (les enceintes arrière et les enceintes
avant, avec une impédance comprise entre
4 Ω et 8 Ω). Si la puissance maximum est
inférieure à 50 W, changez “AMP GAIN” pour
éviter d’endommager vos enceintes (voir page
25 du MANUEL D’INSTRUCTIONS).
• Pour éviter les court-circuits, couvrir les
bornes des fils qui ne sont PAS UTILISÉS
avec de la bande isolante.
• Le dissipateur de chaleur devient très chaud
après usage. Faire attention de ne pas le
toucher en retirant cet appareil.
VORSICHTSMASSREGELN beim
Anschließen der Stromversorgung
und Lautsprecher:
PRECAUTIONS sur l’alimentation et
la connexion des enceintes:
• NE CONNECTEZ PAS les fils d’enceintes
du cordon d’alimentation à la batterie;
sinon, l’appareil serait sérieusement
endommagé.
• AVANT de connecter les fils d’enceintes du
cordon d’alimentation aux enceintes, vérifiez
le câblage des enceintes de votre voiture.
• Die Lautsprecherleitungen des Netzkabels
NICHT an der Autobatterie anschließen, da
sonst das Gerät schwer beschädigt wird.
• VOR dem Anschließen der
Lautsprecherleitungen des
Spannunsgversorgungskabels an die
Lautsprecher, die Lautsprecherverdrahtung in
Ihrem Auto überprüfen.
+
+
TROUBLESHOOTING
• The fuse blows.
* Are the red and black leads connected
correctly?
• Power cannot be turned on.
* Is the yellow lead connected?
• No sound from the speakers.
* Is the speaker output lead short-circuited?
• Sound is distorted.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers
grounded in common?
• Noise interfere with sounds.
* Is the rear ground terminal connected to the
car’s chassis using shorter and thicker cords?
• Unit becomes hot.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers
grounded in common?
FEHLERSUCHE
-
+
R -
-
+
+
EN CAS DE DIFFICULTES
• Die Sicherung brennt durch.
* Sind die roten und schwarzen Leitungen
richtig angeschlossen?
• Stromversorgung kann nicht eingeschaltet
werden.
* Ist die gelbe Leitung angeschlossen?
• Kein Ton aus den Lautsprechern.
* Ist die Lautsprecherausgangsleitung
kurzgeschlossen?
• Ton verzerrt.
* Ist die Lautsprecherausgangsleitung geerdet?
* Sind die (–) Anschlußklemmen der linken und
rechten Lautsprecher zusammen geerdet?
• Störgeräusche im Klang.
* Ist die hintere Erdungsklemme mit kürzeren
und dickeren Kabeln an das Fahrzeugchassis
angeschlossen?
• Gerät wird heiß.
* Ist die Lautsprecherausgangsleitung geerdet?
* Sind die (–) Anschlußklemmen der linken und
rechten Lautsprecher zusammen geerdet?
+
L -
• Le fusible saute.
* Les fils rouge et noir sont-ils racordés
correctement?
• L’appareil ne peut pas être mise sous
tension.
* Le fil jaune est-elle raccordée?
• Pas de son des enceintes.
* Le fil de sortie d’enceinte est-il court-circuité?
• Le son est déformé.
* Le fil de sortie d’enceinte est-il à la masse?
* Les bornes “–” des enceintes gauche et droit
sont-elles mises ensemble à la masse?
• Interférence avec les sons.
* La prise arrière de mise à la terre est-elle
connectée au châssis de la voiture avec un
cordon court et épais?
• L’appareil devient chaud.
* Le fil de sortie d’enceinte est-il à la masse?
* Les bornes “–” des enceintes gauche et droit
sont-elles mises ensemble à la masse?
2
Om kortsluiting te voorkomen adviseren wij u om de
minpool van de accu los te maken en alle elektrische
verbindingen tot stand te brengen voordat u het
apparaat in de auto installeert.
• Aard dit toestel beslist weer op het chassis
van de auto na het installeren.
Opmerkingen:
• Vervang de zekering door een exemplaar met het
aangegeven vermogen. Als de zekering vaak
doorslaat, moet u uw JVC car audio dealer
raadplegen.
• Sluit bij voorkeur luidsprekers met een hoger
maximaal vermogen dan 50 W (zowel achter als
voor, met een impedantie van 4 Ω t/m 8 Ω) aan.
Indien het maximale vermogen lager dan 50 W is,
moet u “AMP GAIN” in de andere stand stellen
zodat de luidsprekers niet kunnen worden
beschadigd (zie bladzijde 25 van de
GEBRUIKSAANWIJZING).
• Om kortsluiting te voorkomen, moet u de
aansluitklemmen van ONGEBRUIKTE gekleurde
draden met isolatieband bedekken.
• De warmte-opnemer kan na gebruik erg heet
worden. Raak de warmte-opnemer niet aan
wanneer u dit apparaat van zijn plaats haalt.
VOORZORGSMAATREGELEN bij het
verbinden van de stroomkabeldraad
met de speakers:
• Verbind de speakerdraden van de
stroomkabel NIET met de accu van de
auto; als u dit wel doet, zal het apparaat
ernstige schade oplopen.
• VOORDAT u de speakerdraden van de
stroomkabel met de speakers verbindt, moet u de
bedrading van de speakers in uw auto controleren.
+
L -
-
+
R -
-
+
+
PROBLEMEN OPLOSSEN
• De zekering slaat door.
* Zijn de rode en de zwarte draden op de juiste
manier aangesloten?
• De stroom kan niet worden ingeschakeld.
* Is de gele draad aangesloten?
• Er komt geen geluid uit de speakers.
* Is de uitgaande speakerdraad kortgesloten?
• Het geluid wordt vervormd.
* Is de uitgaande speakerdraad geaard?
* Zijn de “–” polen van de linker- en de
rechterspeakers gemeenschappelijk geaard?
• Geluid wordt door ruis gestoord.
* Is de aarde-aansluiting achter met gebruik van
kortere en dikkere snoeren met het chassis van de
auto verbonden?
• Het apparaat raakt verhit.
* Is de uitgaande speakerdraad geaard?
* Zijn de “–” polen van de linker- en de
rechterspeakers gemeenschappelijk geaard?
ENGLISH
A
DEUTSCH
Typical Connections / Typische Anschlüsse / Raccordements typiques / Normale verbindingen
Before connecting: Check the wiring in the
vehicle carefully. Incorrect connection may
cause serious damage to this unit.
The leads of the power cord and those of the
connector from the car body may be different in
color.
1
2
3
NEDERLANDS
FRANÇAIS
Connect the colored leads of the power cord
in the order specified in the illustration
below.
Connect the aerial cord.
Finally connect the wiring harness to the unit.
Note: If your vehicle does not have any
accessory terminal, move the fuse from the
fuse position 1 (initial position) to fuse position
2, and connect the red lead (A7) to the positive
(+) battery terminal.
• The yellow lead (A4) is not used in this case.
Vor dem Anschließen: Die Verdrahtung im
Fahrzeug sorgfältig überprüfen. Falsche
Anschlüsse können ernsthafte Schäden am
Gerät hervorrufen.
Die Leiter des Stromkabels und die Leiter des
Anschlusses im Fahrzeug können sich farblich
unterscheiden.
Avant de commencer la connexion: Vérifiez
attentivement le câblage du véhicule. Une
connexion incorrecte peut endommager
sérieusement l’appareil.
Le fil du cordon d’alimentation et ceux des
connecteurs du châssis de la voiture peuvent
être différents en couleur.
Alvorens de verbindingen tot stand te
brengen: Moet u de bedrading in de auto
zorgvuldig. Het apparaat kan door verkeerde
verbindingen ernstige schade oplopen.
De draden van het stroomsnoer verschillen mogelijk
van kleur metde aansluitingen op het chassis van de
auto.
1
Die farbigen Adern des Stromkabels in der
Reihenfolge anschließen, wie in der
Abbildung unten gezeigt.
1
Connectez les fils colorés du cordon
d’alimentation dans l’ordre spécifié sur
l’illustration ci-dessous.
1
Verbind de gekleurde draden van het
stroomsnoer in de afbeelding hieronder
aangegeven volgorde.
2
3
Das Antennenkabel anschließen.
2
3
Connectez le cordon d’antenne.
2
3
Sluit de antenne aan.
Die Kabelbäume am Gerät anschließen.
Hinweis: Verfügt Ihr Fahrzeug nicht über eine
Zubehöranschlußklemme, die Sicherung von
der 1. Sicherungsposition (Erstposition) in die 2.
Sicherungsposition versetzen, die rote Leitung
(A7) an der (+) Batterieanschlußklemme
anschließen.
• Die gelbe Leitung (A4) wird in diesem Fall
nicht verwendet.
Remarque: Si votre véhicule ne possède pas de
borne accessoire, déplacez le fusible de la
position de fusible 1 (position originale) à la
position de fusible 2 et connectez le fil rouge
(A7) à la borne positive (+) de la batterie.
• Le fil jaune (A4) n’est pas utilisé dans ce cas.
To steering wheel remote controller
(see diagram )
An Lenkradfernbedienung (siehe
Diagramm )
Pour la télécommande de volant (voir le
diagramme )
Naar stuurwiel-afstandsbediening (zie
schema )
B1
B3
B5
B7
B2
B4
B6
B8
A2
A4
A5
A7
A6
A8
Black
Schwarz
Noir
Zwart
Aerial terminal
Antennenanschlußklemme
Borne de l’antenne
Aansluitpunt antenne
A8
3
2
Line out (see diagram )
Schutz kappen Signalausgang
(siehe Diagramm )
Sortie de ligne (voir le diagramme
Uitgang (zie schema )
Yellow*2
Gelb*2
Jaune *2
Geel *2
)
To CD changer/DAB tuner or another external
component (see diagram )
An CD-Wechsler/DAB-Tuner oder andere externe
Komponente (siehe Diagramm )
Au changeur de CD/tuner DAB ou à un autre
appareil extérieur (voir le diagramme )
Naar CD-wisselaar/DAB-tuner of ander extern
component (zie schema )
Red
Rot
Rouge
Rood
B3
B5
B7
B2
B4
B6
B8
A5
A7
A2
A4
A6
A8
A4
Verbind de draadbundel daarna met het apparaat.
Opmerking: Als uw voertuig niet beschikt over
een aansluitklem, moet u de zekering verplaatsen
van stand 1 (beginstand) naar stand 2 en moet u de
rode draad (A7) met de pluspool (+) van de accu
verbinden.
• In dit geval wordt de gele draad (A4) niet gebruikt.
Fuse position 2 / 2. Sicherungsposition / Position de fusible 2 / Zekering, stand 2
Fuse position 1 / 1. Sicherungsposition /Position de fusible 1 / Zekering, stand 1
1
*1
*1
*1
*1
Not included for this unit
Wird nicht mit Gerät mitgeliefert
Non fourni avec cet appareil
Niet bij het apparaat inbegrepen
1
To metallic body or chassis of the car
Zur metallenen Karosserie oder zum Fahrwerk des Autos
Vers corps métallique ou châssis de la voiture
Naar metalen ondergrond of chassis van de auto
2
To a live terminal in the fuse block connecting to the car battery
(bypassing the ignition switch) (constant 12 V)
Zur einer stromführenden Anschlußklemme im Sicherungsblock
zum Anschließen an die Autobatterie (Umgehen des
Zündschalters) (konstant 12 V)
À une borne sous tension du porte-fusible connectée à la batterie
de la voiture (en dérivant l’interrupteur d’allumage) (12 V constant)
Naar een onder spanning staande aansluitklem in het zekeringblok die is
aangesloten op de accu van de auto (u passeert de ontstekingsschakelaar)
(constant 12 V)
A7
3
Blue with white stripe
Blau mit weißem Streifen
Bleu avec bande blanche
Blauw met witte streep
*2 Before checking the operation of this unit prior to
installation, this lead must be connected, otherwise power
cannot be turned on.
*2 Vor der Überprüfung der Funktionsfähigkeit des Geräts
vor dem Einbau, muß diese Leitung angeschlossen
werden, da sonst die Stromversorgung nicht
eingeschaltet werden kann.
*2 Pour vérifier le fonctionnement de cet appareil avant
installation, ce fil doit être raccordé, sinon l’appareil ne
peut pas être mis sous tension.
*2 Voordat u controleert of het apparaat werkt (alvorens het te
installeren), moet deze draad aangesloten zijn. Als dit niet het
geval is, kan de stroom niet worden ingeschakeld.
B1
15 A fuse
15 A Sicherung
Fusible 15 A
Zekering 15 A
15
Rear ground terminal
Hintere Erdungscan–
schlußklemme
Borne arrière de masse
Massaklem aan de
achterkant
Finalement, connectez le faisceau de fils à
l’appareil.
Ignition switch
Zündschalter
Interrupteur d’allumage
Ontstekingsschakelaar
*1
*1
Fuse block
Sicherungsblock
Porte-fusible
Zekeringblok
To an accessory terminal in the fuse block
Zur einer Zubehöranschlußklemme im Sicherungsblock
Vers borne accessoire du porte-fusible
Naar een aansluitklem in het zekeringblok
A5
Orange with white stripe
Orange mit weißem Streifen
Orange avec bande blanche
Oranje met witte streep
To the remote lead of other equipment or power aerial if any (200 mA max.)
Zum Zusatzkabel des anderen Geräts oder der Motorantenne, sofern
vorhanden (max. 200 mA)
Au fil de télécommande de l’autre appareil ou à l’antenne automatique s’il y en
a une (200 mA max.)
Naar afstandsdraad van andere apparatuur of antenne met circuit indien aanwezig
(200 mA max.)
4
(ILLUMINATION) A6
Brown
Braun
Marron
Bruin
A2
5
To car light control switch
Zur Autolichtschalter
À l’interrupteur d’éclairage de la voiture
Naar de schakelaar voor de autoverlichting
6
To cellular phone system
Zur Mobiltelefon
À un système de téléphone cellulaire
Naar het mobiele-telefoonsysteem
7
B6
White with black stripe
Weiß mit schwarzem
Streifen
Blanc avec bande noire
Wit met zwarte streep
B5
B4
White
Weiß
Blanc
Wit
Gray with black stripe
Grau mit schwarzem Streifen
Gris avec bande noire
Grijs met zwarte streep
Left speaker (front)
Linker Lautsprecher (vorne)
Enceinte gauche (avant)
Linkerspeaker (voorin)
B3
B8
Gray
Grau
Gris
Grijs
Green with black stripe
Grün mit schwarzem Streifen
Vert avec bande noire
Groen met zwarte streep
Right speaker (front)
Rechter Lautsprecher (vorne)
Enceinte droit (avant)
Rechterspeaker (voorin)
3
B2
B7
Green
Grün
Vert
Groen
Purple with black stripe
Lila mit schwarzem Streifen
Violet avec bande noire
Paars met zwarte streep
Left speaker (rear)
Linker Lautsprecher (hinten)
Enceinte gauche (arrière)
Linkerspeaker (achterin)
B1
Purple
Lila
Violet
Paars
Right speaker (rear)
Rechter Lautsprecher (hinten)
Enceinte droit (arrière)
Rechterspeaker (achterin)
B
Connections Adding Other Equipment / Anschlüsse zum Hinzufügen von anderer Ausrüstung / Raccordement pour ajouter d’autres appareils /
Aansluitingen voor het toevoegen van andere apparatuur
Amplifier / Verstärker / Amplificateur / Versterker
Rear speakers
Hintere Lautsprecher
Enceintes arrière
Achterspeakers
L
INPUT
L
R
R
Vous pouvez connecter un amplificateur ou
autre appareil pour améliorer votre système
autoradio.
• Connectez le fil de commande à distance
(bleu avec bande blanche) au fil de commande
à distance de l’autre appareil de façon qu’il
puisse être commandé via cet appareil.
• Pour l’amplificateur seulement:
Déconnectez les enceintes de cet appareil
et connectez-les à l’amplificateur. Laissez
les fils d’enceintes de cet appareil
inutilisés.
Sie können einen Verstärker oder ein anderes
Gerät anschließen, um Ihre Autostereoanlage
zu erweitern.
• Schließen Sie das Fernbedienungskabel (blau
mit weißem Streifen) an das
Fernbedienungskabel des anderen Geräts an,
so daß es über dieses Gerät gesteuert
werden kann.
• Nur für den Verstärker:
Die Lautsprecher von diesem Gerät
abtrennen und am Verstärker anschließen.
Die Lautsprecherleitungen dieses Geräts
unbenutzt lassen.
You can connect an amplifier and other
equipment to upgrade your car stereo system.
• Connect the remote lead (blue with white
stripe) to the remote lead of the other
equipment so that it can be controlled
through this unit.
• For amplifier only:
Disconnect the speakers from this unit,
connect them to the amplifier. Leave the
speaker leads of this unit unused.
Remote lead
Fernbedienungsleitung
Fil d’alimentation à distance
Afstandbedieningsdraad
JVC Amplifier
JVC Verstärker
JVC Amplificateur
JVC Versterker
Y-connector (not supplied with this unit)
Y-Anschluß (nicht mit diesem Gerät mitgeliefert)
Connecteur Y (non fourni avec cet appareil)
Y-connector (wordt niet bij dit apparaat geleverd)
Remote lead (Blue with white stripe)
Fernbedienungsleitung (Blau mit weißem Streifen)
Fil d’alimentation à distance (Bleu avec bande blanche)
Afstandbedieningsdraad (Blauw met witte streep)
*3
LINE OUT
L
L
R
R
To the remote lead of other equipment or power aerial if any
Zum Zusatzkabel des anderen Geräts oder der
Motorantenne, sofern vorhanden
Au fil de télécommande de l’autre appareil ou à l’antenne
automatique s’il y en a une
Naar afstandsdraad van andere apparatuur of antenne met circuit
indien aanwezig
KD-G302
KD-G301
REAR FRONT
Signal cord (not supplied with
this unit)
Einzelleitung (nicht mit diesem
Gerät mitgeliefert)
Cordon de signal (non fourni
avec cet appareil)
Signaalkabel (wordt niet bij dit
apparaat geleverd)
Front speakers
Vordere Lautsprecher
Enceintes avant
Voorspeakers
Het is mogelijk om uw autostereosysteem uit te
breiden met een versterker of andere apparatuur.
• Verbind de externe kabel (blauw met witte streep)
met de externe kabel van het andere apparatuur
zodat deze op afstand vanaf deze apparaat kan
worden bediend.
• Alleen voor een versterker:
Koppel de speakers van dit apparaat los
en verbind ze aan de versterker. Gebruik
de speakerdraden van dit apparaat niet.
*3 Firmly attach the ground wire to the metallic
body or to the chassis of the car—to the place
not coated with paint (if coated with paint,
remove the paint before attaching the wire).
Failure to do so may cause damage to the unit.
*3 Verbinden Sie den Erdungsleiter mit der
Karosserie oder dem Rahmen des Fahrzeugs.
Die Kontaktstelle darf nicht lackiert sein (sollte
die Kontaktstelle lackiert sein, entfernen Sie
den Lack der Kontaktstelle, bevor Sie den
Leiter befestigen). Wenn der Erdungsleiter
nicht ordnungsgemäß angeschlossen wird,
kann dieses Gerät beschädigt werden.
*3 Attachez solidement le fil de mise à la masse
au châssis métallique de la voiture—à un
endroit qui n’est pas recouvert de peinture (s’il
est recouvert de peinture, enlevez d’abord la
peinture avant d’attacher le fil). L’appareil peut
être endommagé si cela n’est pas fait
correctement.
*3 Bevestig de aardedraad goed met een metalen
onderdeel of het chassis van de auto—bevestig op
een niet-gelakt gedeelte (indien gelakt, schuur dan
af alvorens de draad te bevestigen). Het toestel kan
worden beschadigd indien de aardedraad niet goed
is aangesloten.
CD changer and DAB tuner / CD-Wechsler und DAB-Tuner / Changeur CD et tuner DAB / CD-wisselaar en DAB-tuner
Refer also to page 27 of the INSTRUCTIONS.
Siehe auch Seite 27 in der BEDIENUNGSANLEITUNG.
Référez-vous aussi à la page 27 du MANUEL D’INSTRUCTIONS.
Zie tevens bladzijde 27 van de GEBRUIKSAANWIJZING.
Connecting cord supplied for your DAB tuner
Verbindungskabel, das zum Lieferumfang des
DAB-Tuners gehört
Cordon de connexion fourni avec votre tuner DAB
Verbindingskabel die met de DAB-tuner wordt
meegeleverd
Connecting cord supplied for your DAB tuner or CD changer
Verbindungskabel, das zum Lieferumfang des DAB-Tuners oder CD-Wechslers gehört
Cordon de connexion fourni avec votre tuner DAB ou changeur CD
Verbindingskabel die met de DAB-tuner of CD-wisselaar wordt meegeleverd
Connecting cord supplied for your CD changer
Verbindungskabel, das zum Lieferumfang des
CD-Wechsler gehört
Cordon de connexion fourni avec votre changeur CD
Verbindingskabel die met de CD-wisselaar wordt meegeleverd
JVC DAB tuner
DAB-Tuner von JVC
Tuner DAB JVC
JVC DAB-tuner
JVC DAB tuner
DAB-Tuner von JVC
Tuner DAB JVC
JVC DAB-tuner
JVC CD changer
CD-Wechsler von JVC
Changeur CD JVC
JVC CD-wisselaar
or
oder
ou
of
JVC CD changer
CD-Wechsler von JVC
Changeur CD JVC
JVC CD-wisselaar
KD-G302
KD-G301
KD-G302
KD-G301
CAUTION / VORSICHT / PRECAUTION / LET OP!:
• Before connecting the CD changer and/or the DAB tuner, make sure that the unit is turned off.
• Bevor Sie den CD-Wechsler und/oder den DAB-Tuner anschließen, vergewissern Sie sich,
daß das Gerät ausgeschaltet ist.
• Avant de connecter le changeur CD et/ou le tuner DAB, s’assurer que l’unité est éteinte.
• Zorg ervoor dat het apparaat is uitgeschakeld alvorens u de CD-wisselaar en/of DAB-tuner aansluit.
• You can connect both components in series as illustrated above.
• Es ist möglich, beide Komponenten in einer Serienschaltung entsprechend der obigen
Darstellung anzuschließen.
• Vous pouvez connecter les deux appareils en série comme montré ci-dessus.
• Beide apparaten zijn volgens bovenstaande illustratie in serie aan te sluiten.
External Component / Externe Komponente / Appareil extérieur / Extern apparaat
KS-U57 *4
KD-G302
KD-G301
CD changer jack
Buchse für CD-Wechsler
Prise du changeur CD
Aansluiting voor CD-wisselaar
C
L
L
L
L
R
R
R
R
External component
Externe Komponente
Appareil extérieur
Extern apparaat
Signal cord (not supplied for this unit)
Einzelleitung (nicht mit diesem Gerät mitgeliefert)
Cordon de signal (non fourni avec cet appareil)
Signaalkabel (wordt niet bij dit apparaat geleverd)
*4 Line Input Adapter KS-U57 (not supplied with
this unit)
*4 Line-Eingangsadapter KS-U57 (nicht mit
diesem Gerät mitgeliefert)
*4 Adaptateur d’entrée de ligne KS-U57 (non
fourni avec cet appareil)
*4 Line Input Adapter KS-U57 (wordt niet bij dit
apparaat geleverd)
Connecting to the steering wheel remote controller / Anschluß an die Lenkradfernbedienung / Connexion de la télécommande de volant /
Verbinden met de stuurwiel-afstandsbediening
If your car is equipped with the steering wheel remote controller, you can operate this receiver using
the controller. To do it, a JVC’s OE remote adapter (not supplied) which matches with your car is
required. Consult your JVC IN-CAR ENTERTAINMENT dealer for details.
Wenn Ihr Fahrzeug mit einer Lenkradferndienung ausgestattet ist, können Sie damit diesen Receiver
steuern. Hierfür ist ein für Ihr Fahrzeug passender Radio-Lenkrad-Fernbedienungsadaption von JVC
(nicht im Lieferumfang enthalten) erforderlich. Für weitere Einzelheiten wenden Sie sich an Ihren JVC
Autoradiohändler.
Si votre voiture est munie d’une télécommande de volant, vous pouvez commander cet autoradio en
utilisant la télécommande. Pour le faire, un adaptateur pour télécommande au volant JVC (non fourni)
correspondant à votre voiture est nécessaire. Consultez votre revendeur d’autoradio JVC pour les
détails.
Indien uw auto een stuurwiel-afstandsbediening heeft, kunt u deze receiver met die afstandsbediening bedienen.
Hiervoor heeft u echter een JVC adapter (niet bijgeleverd) nodig die geschikt is voor de stuurwielafstandsbediening van uw auto. Raadpleeg uw JVC car audio dealer voor details.
4
Steering wheel remote input
Eingang für Lenkradfernbedienung
Entrée de la télécommande de volant
Ingang stuurwiel-afstandsbediening
KD-G302
KD-G301
OE remote adapter (not supplied)
Radio-Lenkrad-Fernbedienungsadaption
(nicht im Lieferumfang enthalten)
Adaptateur pour télécommande au volant (non fourni)
Adapter voor stuurwiel-afstandsbediening (niet bijgeleverd)
Steering wheel remote controller (equipped in the car)
Lenkradfernbedienung (im Fahrzeug installiert)
Télécommande de volant (installée dans la voiture)
Stuurwiel-afstandsbediening (in de auto)

JVC KD-G302 User Guide Manual - CaRadio

Transcription

Similar documents

1 Window Jumbo Strip Game

The DAB bank AG banks on C4.

tv tuner cards and video clips

Untitled - Brookstone

Flatbed

BatFink indicator