tools - The GolfWorks

Transcription

0109 P. 96-139 Tools:0507 P. 88-89 Books Tools
12/22/08
1:27 PM
Page 96
TOOLS – GRIP TAPE
GOLFWORKS PROFESSIONAL
GRIP TAPE
Our original standard tape for installing slip-on or leather grips. Sticky on both
sides and activated with solvent. Also keeps grip collars in place. Choose from
18mm wide for spiral winding or 48mm wide for faster length-wise application.
DFTG1
DFTG2
DFTG218
18mm x 36 yd. Roll
48mm x 36 yd. Roll
48mm x 18 yd. Roll
$ 4.49 ea.
$ 9.79 ea.
$ 5.79 ea.
PRE-CUT TAPE STRIPS
DFTG210 1-25 Strips - 2" x 10"
100+ Strips
$ .35 ea.
$ .30 ea.
NOTE: Tape adhesive is solvent activated
GOLFWORKS CLUBMAKERS
GRIP TAPE
The GolfWorks Clubmakers tape has been specifically designed with the professional clubmaker in mind. The adhesive on the underside of the tape has
less aggressive adhesion than the previous versions to better prevent damage
from tape strippers when re-gripping graphite shafts. The adhesive is more than
strong enough to be used with steel shafts as well as graphite. The Clubmakers tape
also is cut at a full 2" width, the size preferred by professional clubmakers.
3
GW1051
/4" x 36 yd. Roll $3.99 ea.
GW1050
2" x 36 yd. Roll
$8.99 ea.
GW1052
2" x 18 yd. Roll
$5.49 ea.
Precut strips of 2" double-coated tape for use in gripping utilizing
our new adhesion formula. Double liners allow stacking of strips for
convenience without sticking together. Just peel off the liner and position the tape
lengthwise on the shaft. Solvent activated.
GW1053
1-25 Strips
$ .35 ea.
NOTE: Tape adhesive is solvent activated
100+ Strips
$ .30 ea.
PRE-CUT TAPE STRIPS
WATER
ACTIVATED TAPE
The best water-activated tape available. Tape is slippery when wet and extremely tacky
when it dries. Best of all, it holds the grip firmly in place under temperature extremes,
resisting twisting and slipping.
WST18
WST10
2" x 18 yd. Roll
25+ Rolls
2" x 10" Strips
100+ Strips
BUILD-UP
TAPE
$ 9.99 ea.
$ 8.99 ea.
$ .40 ea.
$ .35 ea.
This single-coated,
inexpensive masking
tape is used for building up grip sizes. Each
wrap adds about .010"
thickness. Available 3/4"
wide for spiral wrapping or 2" for use lengthwise. Also works great for
masking soleplates and faces during the refinishing process.
3
BU3
/4" x 60 yd. Roll
$ 1.49 ea.
BU2
2" x 60 yd. Roll
$ 3.49 ea.
96
EZ
PEEL TAPE
2" wide grip tape with paper backing that is easily removed.
Perfect for arthritic hands that may have a difficult time peeling off paper backings. One side pre-cut for easy removal.
Makes regripping a snap!
EZDFTG2
2" x 36 yd. Roll
$12.99 ea.
Call Toll Free: 800.848.8358
1/5/09
3:15 PM
Page 97
GRIPPING – TOOLS
UNIVERSAL GRIP
GAUGE
Measures all three important gripping dimensions
— grip size, shaft butt
size, and grip size under
the right hand. This versatile gauge will measure
shaft butt size and grip
size on both men’s and
ladies’ clubs, including
undersized, standard
and oversized. Easily
measures right- and
left-hand grip size.
Made of heavy aluminum with markings etched on a
black background. Full
instructions included.
MAGG
$12.99
DOUBLE-SPOOL
TAPE DISPENSER
GOLFWORKS
GRIP
SOLVENTS
This economical solvent activates all
solvent-activated tapes. Excellent for
easy, efficient grip installation and
shaft cleanup. Available in quart,
gallon, aerosol and 16 oz. cans.
GW0037 $3.99 16oz. can
SOMQT $5.99 1 Quart Can
SOMGL $18.99 1 Gallon Can*
NFGA
$4.99 11.5 oz. Aerosol
NOTE: ADDITIONAL SHIPPING CHARGES MAY BE REQUIRED DUE TO WEIGHT.
Handy, refillable bottle. Use for solvents, oils, thinners and most other
liquids. 8 oz. capacity.
SQ27 $ .99
PLASTIC SQUEEZE BOTTLE
NOTICE: CANNOT BE
SHIPPED BY AIR.
Now, a dispenser to handle doublecoated grip tape and build-up
tape. Conveniently winds the
discarded liner onto a
spool for easy disposal.
Includes a heavy
duty base that is
sturdy enough to be free
standing, or can be attached
to a workbench. Smooth
pulling action and saw tooth
cutting blade.
BRAMPTON
TECHNOLOGY
HF100 GRIP
SOLVENT
Non-toxic, non-flammable and odorless solvent
that is reusable. HF100 solvent is more effective
than other solvents, working well with up to
60% less.
GW1100 $119.99
4 oz. Pump Spray Bottle
HF4
$2.99
8 oz. Pump Spray Bottle
HF8
$3.99
Quart
HF100
$8.99
Spray Nozzle for Quart Bottle
SPRN
$1.99
Kit of HF100 Quart w/Spray Nozzle
HFKIT
$9.99
Gallon*
HF10G
$19.99
DOUBLE-COATED
TAPE DISPENSER
“Pull ‘n Cut” dispenser for tape rolls
eliminates sticky handling of double-sided
tape when installing grips.
Conveniently winds discarded
liner onto a spool for disposal.
Works for both 3/4"
and 2" rolls.
* Due to weight, gallon sizes of gripping solvents
require additional shipping charges.
DSTD
$79.99
GRIP ESSENTIALS KIT
SOLVENT CATCH
BASIN
Plastic catch basin
mounts directly
onto your workbench at the side
of your vise to
catch excess solvent from grip
installation. Plastic
hose allows you to
drain solvent back
into container for re-use.
UCMVGP
Introducing the ultimate gripping and
regripping supply package — our new Grip
Essentials Kit. For just one low price, you
will receive seven
gripping tools and
supplies that make
the job
a snap.
INCLUDES:
• Double Sided Grip Tape
• Universal Grip Gauge
• Utility Knife w/Hook Blades
• Grip Installer
• Tape Stripper
• Grip Solvent 16 oz.
• Rubber Shaft Clamp
DFTG218
MAGG
GWUK
BBGIT
GW1101
GW0037
RSC
$5.79
$12.99
$4.99
$9.99
$14.99
$3.99
$1.99
GW1212 $29.99
SAVE OVER $2400!
NOTICE: CANNOT BE
SHIPPED BY AIR.
$14.99
Go To: www.golfworks.com — Open 24 Hours Per Day!
97
12/22/08
1:29 PM
Page 98
TOOLS – GRIPPING
UTILITY KNIFE
RHINO RIP™ GRIP CUTTER
STRAIGHT
STRAIGHT
A sensational
STANDARD
THIN
package that
handles all your
cutting needs.
The GolfWorks
Utility Knife
Kit includes:
HOOK
• A high-quality DULL
utility knife
• 5 straight
blades
• 5 thin blades
for precision
cutting
• 5 hook blades for grip removal
• 5 dull tip blades, protects graphite shafts
Faster and safer than any other grip removing tool. The Rhino Rip will quickly remove
rubber, cord, polymer and leather grips. Safe to use on steel and graphite
clubs. Long-lasting blade will remove hundreds of grips. The Rhino Rip
Bench Mount Tool mounts to any work bench and
securely holds the grip in place during the
removal process.
RR0001 Rhino Rip Grip Cutter
$19.99
RR0002 Replacement Blades pkg. of 3 $9.99
RR0003 Rhino Rip Bench Mount Tool $4.99
GRIP
SAVER
This handy little tool allows you to remove a rattle in a shaft or place lead and a cork down
the shaft of a club without damaging the grip.
GWUK
$4.99
Kit (knife with blades)
GWUKRSB $1.99
(5 straight replacement blades)
GWUKRHB $2.49
(5 hook replacement blades)
SAVER
Hold shafts securely during the tape removal process.
The Plug is designed to attach to the side of a work
bench (screws provided) and give
you a solid hold on the butt end of
the shaft while scraping off old
tape. The Plug extends out
approximately 11/2" from the
bench. A nylon ring protects
tape stripping tool.
TAPE REMOVAL PLUG
$12.99
This heavy-duty knife is ideal for grip removal and other clean-up jobs. A “must
have” for any shop! The 4" long x 11/4" wide carbon steel blade
is riveted to the wood handle.
THE SUPER KNIFE
H404
GW1007 $9.99
TAPE
STRIPPER
This handy tool saves you time and energy when stripping grip tape off a shaft. The cutting end is curved
to fit the shaft, cleanly stripping tape from graphite or steel shafts in just a few strokes.
Ball handle for comfort. The Tape Stripper's specially designed blade can
be resharpened.
GW1101 $14.99
GRIP
CAP SAVER
The GolfWorks Grip Cap Saver is a must have when installing shafts with grips that are already installed.
The cap slips onto the grip cap and helps eliminate the chance of the shaft butt cutting through the cap.
The Grip Cap Saver disperses the pressure away from the center of the grip without damaging the grip
cap. Made of high strength nylon for durability.
GW1031
$9.99
98
without
Grip Saver
with
Grip Saver
$9.99
12/22/08
1:29 PM
Page 99
GRIPPING – TOOLS
PRESSURIZED
GRIP REMOVER
Now you can remove AND reinstall a grip!
Ideal for a repair shop or clubmaker. This
durable pump holds lots of solvent.
Convenient cap for needles minimizes
breakage. Five 18-gauge needles and
extension hose are included.
Please Note: Our Economy Grip Solvent
works best with this tool. DO NOT USE
perchlorethylene as it dissolves neoprene
seals. To prevent damage to seals, store
liquid in another container.
GS6
1. Push needle into grip.
$59.99
2. Inject solvent to loosen grip.
D
C
3. Remove grip in perfect
condition.
A
B
REPLACEMENT PARTS
A. GSP Grip Shooter Pump (Metal)
GSPP Grip Shooter Pump (Plastic)
B. GSRK Grip Remover Repair Kit
C. HOSE Replacement Extension Hose
D. NECV Grip Needle Cover
E. IGSN5 Needles (package of 5)
F. GRRS Repair Service
E
Shown with Extension
Hose Attached
$29.99
$29.99
$ 6.99
$14.99
$ 1.55
$13.99 5 pk.
$19.99
V-GROOVE
GRIP REMOVER
Just pour some solvent in the V-Groove Grip Remover and slide it into place — a
great way to save the grip for re-use!
VGGR $19.99
ULTIMATE GRIP
INSTALLER TOOL
The best tool for installing grips. Essential for installation on
big butt shafts as well as conventional shafts, making
grip installation much quicker.
BBGIT
$9.99
GRIP BORE CLEANER
Clean tape and residue from inside the grip before reinstalling. Bristles are spiral wound steel fibers and
effectively remove dried-on tape or lumpy old tape residue. Another “must have” for the shop.
GBCT
$8.49
99
12/22/08
4:43 PM
Page 100
TOOLS – GRIPPING
GOLFWORKS
QUICK-GRIP
SUPER FAST & EASY TO USE!
The GolfWorks Quick Grip is a must have tool for any
repair shop. Originally designed as a method to install rubber grips onto ultra light weight shafts, the GolfWorks Quick
Grip soon became our favorite method for installing rubber
grips onto all types of golf shafts. Quick and easy to use the
Quick Grip keeps your hands free of solvent and produces
identical grip lengths and sizes throughout the set. Can be
bench mounted or used with the optional Quick Grip Vise Adaptor (shown
below - GW1037).
• Recommended grip installation method for installing grips onto
ultra light weight shafts. Eliminates chance of shaft being damaged
by over tightening in a clamp or vise.
• Consistent grip sizes and installed grip lengths.
• Durable enough for high volume shops.
• Compact design doesn’t take up much bench space.
• Solvent never touches your hands.
• Can be mounted directly to work bench or used with optional
vise mount attachment (GW1037)
• Excess solvent flows through attached tube for disposal or re-use.
• Best used with GolfWorks Aerosol Grip Solvent (NFGA).
*Note – The quick grip will not install wrapped two piece
synthetic grips that are secured by tape.
GW1030 $39.99 Quick-Grip
GW1037 $12.99 Quick-Grip Vise Adaptor (below)
NFGA*
$4.99 Aerosol Grip Solvent (required)
GW1030C $ .45 Replacement Clips
*NOTICE: CANNOT BE SHIPPED BY AIR.
This adaptor allows you to
place the Quick Grip tool in
your bench-mounted vise.
Constructed of high quality,
durable, lightweight aluminum.
1
2
• Slide grip over installer fingers
• Load grip into the Quick Grip clamps
4
3
• Spray solvent on grip tape
5
• Spray solvent onto grip
7
6
QUICK-GRIP VISE ADAPTOR
NOTICE: CANNOT BE
SHIPPED BY AIR.
• Insert golf shaft
• Remove
QUICK GRIP KIT
The Quick Grip Kit includes the Maltby Design Quick Grip, vise mount attachment, a roll of
double coated tape and a can of GolfWorks Aerosol Grip Solvent. Priced separately they total
over $67.00! DVD instructions included.
INCLUDES:
• Quick Grip (GW1030 - reg. $39.99)
• Vise Mount Adaptor for Quick Grip (GW1037- $12.99)
• Professional Grip Tape (DFTG2 - $9.79)
• GolfWorks Aerosol Solvent (NFGA - $4.99)
GW1202
This clamp is an absolute necessity for regripping, assembling
clubs and reshafting. It slips over the shaft and is
placed in the vise to hold the shaft or
club securely without crushing or marring it. Made of synthetic material with
ribbed sides, it is 3 1/2" long. Can be
used for graphite shafts.
5499 SAVE $12!
$
SHAFT VISE CLAMP
PROFESSIONAL METAL-SIDED
SHAFT CLAMP
RSC
EMSC
100
$1.99
This durable, heavy duty professional shaft
clamp is easy to use. Made of heavy gauge steel
on the outside and vulcanized rubber on the
inside, it's a must for every shop. Note: Can be
used for graphite shafts.
$8.99
12/22/08
1:31 PM
Page 101
GRIPPING– TOOLS
MALTBY ® MASTER
GRIPPING STATION
MA2016
The most complete gripping station available. Integrated unit
that allows you to grip and regrip clubs at one station, with
everything you need close at hand. Add the optional
Grip Rip for ultimate efficiency.
FEATURES:
• Portable or Floor Mount Stands - Available
• Adjustable Height - Six different adjustments
• Optional Grip Rip - Mounts at the base of station
• Dual Tape Dispenser - Removes tape backing and also holds build-up tape
• Pro Lever-Action Shaft Clamp - For efficient loading and unloading
• Rubber Coated Clamp - Safe for graphite shafts
• Solvent Recovery Pan - Includes shutoff valve to keep solvent in pan
• Solvent Bottle Holder - Fits Brampton Spray Bottle
MA2015
• Tape Stripper - Stays in holder on unit
• Tape Stripping Anchor - Anchor point for butt end of shaft while stripping
• Utility Trays - Two removable trays to hold solvent and gripping supplies,
Lower tray holds gallon jug to recycle solvent
PORTABLE FEATURES:
• Non-Slip Stand - Foot stand channels spilled solvent away
• Adjustable Platform - Standing platform adjusts for reach
MA2015 (Portable) $429.99
MA2016 (Floor Mount) $409.99
GRP Grip Rip (optional) $109.99
RBLA Grip Rip Replacement Blade (optional) $3.99
Optional
Grip Rip GRP
NOTE: ADDITIONAL SHIPPING CHARGES REQUIRED DUE TO WEIGHT.
GOLFWORKS GRIPPING STATION
Save valuable time and improve consistency of your regrips with this well-designed Gripping
Station. Built to last under high-volume production. Alignment bar indexes leading edge of
right- and left-handed woods and irons, ensuring proper alignment. Includes a solvent recovery
pan and tape dispenser for one roll each of double-sided tape and
build-up tape. Vise not included.
GGS
$109.99
GOLFWORKS
GRIPPING KIT
SAVE $2500!
All you need to perform quick and professional gripping. The GolfWorks gripping
kit includes the GolfWorks gripping station, tape (double coated and build up), a
gallon of solvent and the GolfWorks Universal Grip Gauge. Save over $23 when
purchased as a kit.
INCLUDES:
• GOLFWORKS Gripping Station (GGS reg. $109.99 ) NOTICE: CANNOT BE
• 2" Double Sided Tape (DFTG2 reg. $9.79 )
SHIPPED BY AIR.
• 2" Build Up Tape (BU2 reg. $3.49 )
• 1 Gallon Gripping Solvent (SOMGL reg. $18.99)
• GolfWorks Universal Grip Gauge (MAGG reg. $12.99 )
TOTAL VALUE: $155.25
GGSK $129.99
101
12/22/08
1:34 PM
Page 102
TOOLS – EPOXY
GOLFWORKS®
MAXIMUM
STRENGTH
High Impact &
Tour Set Plus
EPOXY
The new GolfWorks Maximum Strength High Impact and Tour Set Plus Epoxies
have been formulated to match the peel and shear strength of premium 3M®
epoxies only with more elastic qualities specifically needed for proper golf club
head/shaft adhesion, at about half the cost. The Maximum Strength High Impact
epoxy is formulated for the high volume clubmaker to gel in approximately 1 hour
while the Maximum Strength Tour Set Plus epoxy with a gel time of 20-30 minutes
is intended for smaller jobs and/or when you simply need to expedite the curing
process. Both Maximum Strength epoxies feature a shear strength of 4500 psi and
require a 2:1 mix ratio. The GolfWorks Epoxy Cartridge Gun (ESG2) equipped
with a 2:1 plunger (VB1004) is required for proper dispensing. Epoxy Gun with
1:1 and 2:1 plunger also available (VB1005).
Stronger Adhesion At Half The Cost!
Maximum Strength High Impact Epoxy 50 ml. Cartridge
VB1001 $9.99
Maximum Strength Tour Set Plus Epoxy 50 ml. Cartridge
VB1002 $10.99
GOLFWORKS®
MAXIMUM
STRENGTH
Quick Set
EPOXY
Recommended By
The GolfWorks Staff!
EPOXY CARTRIDGE GUN
The Professional Epoxy Cartridge Gun holds all GolfWorks 50 ml. cartridges, ensuring easy and consistent dispensing of all epoxy in accurate amounts. The added leverage of the gun makes dispensing small controlled amounts easy, and ensures even
mixing. Smooth action makes the gun simple and easy to use. Durable plastic and
metal construction.
Minimize Waste & Ensures Proper Mixing Ratios!
The new GolfWorks Maximum Strength Quick Set
Epoxy is the strongest “5 minute” epoxy available,
specifically formulated for wood and iron club assembly.
Standard “5 minute” epoxies are only recommended for
putter assembly and temporary emergency repairs. With
a full cure lap shear strength of 2900 psi and a usable
cure time of 15-30 minutes, the Maximum Strength
Quick Set eliminates the need for unreliable one part
cyanoacrylate adhesives and is much more reliable than
standard “5 minute” shafting epoxies with average lap
shear strengths of 1500 psi. Maximum Strength Quick
Set is black in color with a mix ratio of 1:1. Thumb
plunger for dispersion is included.
Maximum Strength Quick Set Epoxy
50 ml. Cartridge
VB1003 $10.99
GOLFWORKS®
Epoxy Gun w/1:1 Mix Ratio Plunger
ESG2
Epoxy Gun w/1:1 & 2:1 Ratio Plunger VB1005
Individual 2:1 Ratio Plunger for ESG2
1:1
2:1
102
VB1004
$26.99
$29.99
$3.99
12/22/08
1:35 PM
Page 103
EPOXY – TOOLS
TOUR
SET EPOXY
Tour Set Epoxy combines the strength of long-cure epoxies with the
TOUR
SET PLUS EPOXY
All the convenience and bonding strength of the standard Tour Set, but with
conveniences of shorter cure epoxies. Tour Set
has a gel time of 12 minutes. Cures to playing
strength in 60-90 minutes, depending on
temperature. Available in two-4 oz. bottles or
a 50 ml. cartridge.
a gel time of 25-35 minutes, allowing for more clubs
to be done with one mix. Cures to playing strength in
60 to 90 minutes, depending on temperature.
Available in two-4 oz. bottles or a 50 ml. cartridge.
TSP4
TSPE
PSB4 Two 4 oz. Bottles $14.99
PSSE 50 ml. Cartridge
$9.50
GRAPHITE SHAFTING
EPOXY
Super-strength, high-impact epoxy designed for
Two 4 oz. Bottles
50 ml. Cartridge
$16.99
$9.99
ULTIMATE
FLEX
EPOXY
Our strongest epoxy, the new Ultimate Flex formula is
shear strength with pliability. Reduce stress on
the shaft tip at impact, ideal for bonding graphite
shafts to heads. Available in two-4 oz. bottles
or a 50 ml. cartridge.
GREX4
GREX1
Two 4 oz. Bottles
50 ml. Cartridge
also more "flexible" than other high impact epoxies
making it the most vibration and shock resistant golf
specific epoxy on the market. Grey in color, gels in 8
hours and sets in 24 hours.
Available in a 50 ml.
cartridge or 3 job size packets.
$12.99
$8.99
GW0042 $9.99
50 ml. Cartridge
VB1006 $3.99
3 Job Size Packets
w/Mixing Sticks
QUICK SET
SHAFTING
EPOXY
Quick set epoxy is perfect for that quick repair. High
HIGH IMPACT
BEADED EPOXY
CARTRIDGE
Easy-to-use beaded epoxy is ideal for assembly when the shaft to
strength formula sets in 5 to 10 minutes. Bonds to
metal, graphite and
wood. Available in a
50 ml. cartridge or
3 job size packets.
hosel fit is not tight. Beads fill the void and provide cushion at
impact! 50 ml. cartridge.
EPCXBC
50 ml. Cartridge
$8.99
GWSY
$8.99
50 ml. Cartridge
VB1008 $3.49
3 Job Size Packets
w/Mixing Sticks
EPOXY CHART
Code
VB1001
VB1002
VB1003
K20/K22
EPX
PSSE
TSPE
GREX
GW0042
GWSY
SEPX
Description
Maximum Strength High Impact Epoxy
Maximum Strength Tour Set Epoxy
Maximum Strength Quick Set Epoxy
Conap
GolfWorks High Strength Epoxy
Tour Set Epoxy
Tour Set Plus Epoxy
Graphite Shafting Epoxy
Ultimate Flex Epoxy
Quick Set Epoxy
Single Club
Cartridge
*
*
*
*
*
*
*
*
*
Mix Ratio
2:1
2:1
1:1
2:1
1:1
1:1
1:1
1:1
1:1
1:1
1:1
Set/Gel
Time
60 min
20-30 min
4-7 min
2 hrs
8 hrs
12 min
25-35 min
8 hrs
8 hrs
5-10 min
8 hrs
Usable
Cure Time
6-8 hrs.
4 hrs.
15-30 min
4 hrs.
18 hrs.
1 hr.
1 hr.
18 hrs.
18 hrs.
1 hr.
18 hrs
Full
Cure Time
24 hrs
24 hrs
24 hrs
24 hrs
24 hrs
24 hrs
24 hrs
24 hrs
24 hrs
24 hrs
24 hrs
103
12/22/08
2:20 PM
Page 104
TOOLS – EPOXY
GOLFWORKS®
HIGHSTRENGTH
EPOXY
This high-impact, high-strength epoxy is formulated
for clubmakers. Creates a very strong bond. High
shear strength for very high torque resistance.
Available in 50 ml. cartridge as well as in
squeeze bottles.
EPX1
EPX4
EPX8
EPX16
EPX32
50 ml. Epoxy Cartridge
8 oz. EZ Pour Epoxy
16 oz. EZ Pour Epoxy
$5.99
$7.99
$13.99
$19.99
$36.99
OUR BIGGEST
SELLERS!
High strength epoxy in a convenient single use pack – just enough to shaft one club.
Each packet has A and B parts ready for mixing.
SINGLE CLUB EPOXY
Single Use Packet
SEPX
$.99
3 Job Size Packets w/Mixing Sticks
VB1007 $3.49
High shear strength to meet the high standards of many
proline manufacturers. Maximum strength obtained in
24 hours. Includes A and B formulations, mixing board
and applicators. Clear or Black.
CONAP
EPOXY
K20
K22
Clear Kit
Black Kit
$14.99
$14.99
NOTICE: CANNOT BE
SHIPPED BY AIR.
™
QUIK CENTER
Improves Bonding!
Eliminate off-center shaft assembly and ensure a
proper epoxy bond with our Quik Center filler.
The small beads, when mixed with epoxy ensure
that the shaft is centered in an otherwise loose
fitting hosel.
The added particles improve the strength of the
bond too!
QCSB
$4.99
GLASS
SHAFTING
BEADS
When assembling a golf club, these real
Glass Shafting Beads can ensure that the
golf shaft will be properly centered in the
hosel. Mix the Glass Shafting Beads directly into your epoxy mix. The 4 ounce jar
provides enough shafting beads for use in
hundreds of clubs.
GW0043 4 oz.
104
$4.99
12/22/08
2:21 PM
Page 105
EPOXY SUPPLIES – TOOLS
6" EPOXY MIX &
APPLICATOR
STICKS
METRIC
MIXING CUPS
Accurately and completely mix twopart epoxies with these inexpensive,
disposable measuring cups. Transparent
so you can easily see that you mix thoroughly. Marked in ounces, tablespoons,
grams and milliliters. Package of 25.
These 6" white birch sticks are ideal
for mixing and applying epoxies. They
are pliable and durable, and will hold
up for repeated use. Ideal when used
with the Mixing Cups (MC30) for
mess-free epoxy mixing and
application.
TDHE
MC30
$1.99
$2.99
EPOXY
CLEANING
SOLVENT
Professional use solvent that removes epoxy
EPOXY SPATULA
The Epoxy Spatula has a specially designed tip section that is angled
and flattened for proper epoxy mixing. Excellent for inserting epoxy
into the clubhead's hosel. Epoxy always bonds better when applied to
both surfaces prior to assembly, making this tool a necessity for the
serious clubmaker. To remove epoxy from tool after use, simply wipe
off or allow the epoxy to dry and peel to remove.
residue from shafts, heads, tools, benches,
etc. . . Contains universal solvent that cleans
up resins, urethanes, stains and pigments.
Test before using on painted or clear-coated
finish. Quart.
GW0036 $3.99
ECS
$11.99
NOTICE: CANNOT BE
SHIPPED BY AIR.
HEAD TACKING
ADHESIVE
LATEX
GLOVES
Our factory craftsmen
use these lightly dusted,
latex gloves to
protect their
hands from
epoxy, solvents,
dust and dirt
during club
assembly and
repair. Large size
fits right or left
hands and stretches
to fit most anyone.
Box of 100.
EG100
Stops Annoying Rattles!
Clubhead Tacking Adhesive is a sticky compound
used to coat the inside of a head, trapping particles
and eliminating rattles. Now available in a syringe
for easy insertion into metal wood hosel bores or a
pre-drilled hole into the metal wood shell. Can also
be used to safely add weight to metal wood heads.
Use a metal wood plug (MWHBP) to fill hosel
hole before replacing shaft.
CLHT
4 oz. $7.99
GW0035 Syringe $8.99
$16.99
™
KIM
WIPES
These convenient all purpose wipes are lint
free and perfect for cleaning
epoxy from hosels and applying
acetone to ferrules as well as many
other uses around the shop. Box of
280 wipes.
GW0015
Box of 280
$2.99
GOLF CLUB
CURING/
DISPLAY
RACK
A great addition to any
shop (or den)! The
Golf Club Curing rack
safely holds your clubs
while epoxy cures,
ensuring that the bond
is strong and alignment
is not compromised. It
is also a great rack for
displaying clubs in a
shop or home.
GW1114 $59.99
105
12/22/08
3:14 PM
Page 106
TOOLS – FERRULES
HUGE FERRULE SELECTION!
A complete selection of ferrules with modern outside diameters that match perfectly to the outside diameter of hosels. All ferrules have a 19° countersink which allows a cushion of epoxy to form between the top
of the hosel and the inside of the ferrule, strengthening the bond. Each ferrule also is “pre-washed,” arriving at your shop with a high-gloss finish and no need for an acetone wipe to make it shine!
52 PW
52 PI
70 PI
55 PW
55 PI
72 PI
62 OW
63 OW
64 OW
75 TI
53 PW 54 PW
53 PI
54 PI
71 PI
56 PW
56 PI
57 PW
57 PI
73 PI
58 PW
58 PI
59 PW
59 PI
60 PW
60 PI
74 PI
61 PW
61 PI
65 TI
76 TI
66 TI
80PW
67 TI
81PW
WOOD FERRULES
Code
Desc.
52PW Standard
53PW Standard
54PW Standard
55PW Standard
56PW Standard
57PW Standard
58PW Standard
59PW Short
60PW Standard
61PW X-Long
62OW Mid 350
63OW Mid 370
64OW Mid 400
80PW
81PW
82PW
83PW
Color
Black
Black
Black
Black
Black
Black
Black
Black
Black
Black
Black
Black
Black
Black
Black
Black
Black
Ring Color
Black/ Chrome
Black/White
Black/Gold
Black/Red
Clear/Black/Clear
Gold/Black/Gold
Chrm/Black/Chrm
none
none
none
none
none
none
none
none
none
Chrome
Length
.500"
.500"
.500"
.500"
.500"
.500"
.500"
.250"
.500"
.788"
.350"
.350"
.350"
.550"
.500"
.550"
.550"
OD
.505"
.505"
.505"
.505"
.505"
.505"
.505"
.505"
.505"
.510"
.525"
.525"
.525"
.525"
.525"
.535"
.535"
ID
.335"
.335"
.335"
.335"
.335"
.335"
.335"
.335"
.335"
.335"
.350"
.370"
.400"
.335"
.335"
.350"
.350"
Dozen
$3.99
$3.99
$3.99
$3.99
$3.99
$3.99
$3.99
$2.49
$2.49
$2.49
$2.49
$2.49
$2.49
$2.49
$2.49
$2.49
$3.99
Each
$0.50
$0.50
$0.50
$0.50
$0.50
$0.50
$0.50
$0.35
$0.35
$0.35
$0.35
$0.35
$0.35
n/a
n/a
n/a
n/a
Chrome
Chrome
White
Gold
Gold
Red
Clear/Black/Clear
Gold/Black/Gold
Gold/Black/Gold
Chrm/Black/Chrm
Chrm/Black/Chrm
none
none
none
none
.500"
.650"
.500"
.500"
.650"
.500"
.500"
.500"
.650"
.500"
.650"
.250"
.500"
.650"
.788"
.540"
.550"
.540"
.540"
.550"
.540"
.540"
.540"
.550"
.540"
.550"
.540"
.540"
.550"
.540"
.370"
.370"
.370"
.370"
.370"
.370"
.370"
.370"
.370"
.370"
.370"
.370"
.370"
.370"
.370"
$3.99
$3.99
$3.99
$3.99
$3.99
$3.99
$3.99
$3.99
$3.99
$3.99
$3.99
$2.49
$2.49
$2.49
$2.49
$0.50
$0.50
$0.50
$0.50
$0.50
$0.50
$0.50
$0.50
$0.50
$0.50
$0.50
$0.35
$0.35
$0.35
$0.35
.500"
.875"
1.00"
.875"
.875"
.570"
.570"
.570"
.550"
.570"
.355"
.355"
.355"
.355"
.355"
$2.49
$2.49
$2.49
$3.99
$3.99
$0.35
$0.35
$0.35
$0.50
$0.50
68WIR
IRON FERRULES - .370" SHAFTS
52PI
Standard
Black
70PI
Long
Black
53PI
Standard
Black
54PI
Standard
Black
71PI
Long
Black
55PI
Standard
Black
56PI
Standard
Black
57PI
Standard
Black
73PI
Long
Black
58PI
Standard
Black
72PI
Long
Black
59PI
Short
Black
60PI
Standard
Black
74PI
Oversized
Black
61PI
X-long
Black
82PW
IRON FERRULES - .355" TAPERED SHAFTS
65TI
Standard
Black
none
66TI
X-Long
Black
none
67TI
XX-Long
Black
none
75TI
X-Long
Black
Chrome
76TI
X-long
Black
Gold
FOR OEM
FERRULES & ADAPTORS –
SEE PAGE 108
O-RINGS
68WIR Rubber O Rings
Various
$2.25 $0.35
83PW
COLLARED
FERRULES
Collared Ferrules are designed specifically for
use with graphite shafts. Ferrule collar fits into
club head hosel to cushion contact
point between shaft and hosel
IRON FERRULES
Code
Desc.
BB0001 Collared
WOOD FERRULES
BB0002 Collared
BB0003 Collared
Color
Black
Ring Color
none
Black
Black
none
none
Length OD
ID Dozen
.750" .545" .370" $2.99
.250" .485" .335" $2.99
.250" .545" .350" $2.99
BB0003—Works for .350" Wood and .355" Irons
IRON FERRULES
BB0004 Collared
BB0006 Collared
WOOD FERRULES
BB0005 Collared
BB0007 Collared
Black
Black
none
none
.250" .545" .370" $2.99
.500" .485" .335" $2.99
Black
Black
none
none
.500" .545" .335" $2.99
.500" .545" .350" $2.99
BB0007—Works for .350" Woods and .355" irons
BB0001
106
BB0006
BB0002
IRON FERRULES
BB0008 Collared
Black
none
.500" .545" .370" $2.99
12/22/08
3:14 PM
Page 107
FERRULES – TOOLS
GOLFWORKS SMALL PARTS KITS
BLACK
FERRULE
KIT – 192 PCS
• 60PI 2 Doz.
• 74PI 2 Doz.
• 61PI 2 Doz.
• 59PI 2 Doz.
• 64OW 1 Doz.
• 61PW 1 Doz.
• 67TI 1 Doz.
• 60PW 1 Doz.
• 59PW 1 Doz.
• 62OW 1 Doz.
• 65TI 1 Doz.
• 68WIR 1 Doz.
GW2001 $39.99
Parallel Irons
Tapered Irons
Parallel Woods
Oversized Woods
SWINGWEIGHT
KIT – 169 PCS
1 Dozen each:
• 2, 4, 6, 8, 10 gm.
Wood Tip Weights
• 2, 4, 6, 8, 10 gm.
Iron Tip Weights
• 2, 4, 5 gm.
Graphite Shaft Tip Weights
• Shaft Butt Weight Ports
• 1 lb. Lead Powder
GW2005 $34.99
COLOR RING
FERRULE KIT
– 264 PCS
• 52PI
• 70PI
• 54PI
• 71PI
• 53PI
• 56PI
• 57PI
• 73PI
• 58PI
2 Doz.
2 Doz.
2 Doz.
2 Doz.
1 Doz.
1 Doz.
1 Doz.
1 Doz.
1 Doz.
OEM
ADAPTOR
KIT – 100 Pcs
• 72PI 1 Doz.
• 75TI 1 Doz.
• 76TI 1 Doz.
• 52PW 1 Doz.
• 54PW 1 Doz.
• 56PW 1 Doz.
• 57PW 1 Doz.
• 58PW 1 Doz.
• 53PW 1 Doz.
SAVE $2600
Brand
TaylorMade
TaylorMade
TaylorMade
TaylorMade
TaylorMade
TaylorMade
TaylorMade
Callaway
Callaway
Callaway
Callaway
Code
Size
BB9007 .370"
BB9014 .370"
BB9015 .350"
BB9008 .335"
BB9009 .350"
TM335AD .335"
TM335AD .350"
BB9003 .370"
BB9005 .335"
BB9006 .350"
CSS
.350"
Fits
Qty
TaylorMade RAC, HT, LT + OS Irons
12
TaylorMade R7 Irons
12
TaylorMade Rescue Hybrids
12
TaylorMade R5,R7,Burner + Super Quad Wds 4
TaylorMade R5,R7,Burner + Super Quad Wds 4
TaylorMade Series 500 Wds
2
TaylorMade Series 500 Wds
2
Most Callaway Irons
12
Older Callaway Drivers + FW Woods
5
Older Callaway Drivers + FW Woods
5
FT-5, FT-I, X-460, Big Bertha 460,
Big Bertha 454, VFT, ERC II, Steel Head III,
4
+ Great Big Bertha II
Callaway
BB9002 .335" FT-5, FT-I, X-460, Big Bertha 460,
4
+ Great Big Bertha II
Ping
BB9016 .335" G5 Drivers, G5 Fairway Wds + G2 Drivers
3
Ping
BB9017 .350" G5 Drivers, G5 FW Wds + G2 Drivers
3
Ping
BB9010 .335" G2 FW Woods RH
2
Universal
BB9018 .335" Universal Plastic Shim w/Attached Ferruleinstalls .335" shafts into a .350" hosel bore. 5
Nike
BB9020 .335" Sumo Drivers
4
Nike
BB9019 .335" Sasquatch Drivers
4
DC0002
– 18 compartment parts box
1
100 PCS.
GW2007 $99.99 100 Piece OEM Adaptor Kit
SMALL PARTS
& SHIM
KIT – 128 Pcs
•
•
•
•
•
GW2002 $89.99
Parallel Irons
Tapered Irons
Parallel Woods
Brass Shims
Bore Through Pins
Metal Wood Bore Plugs
Split Ferrules
Universal Bushing Ferrules/Shims
GW2004 $44.99
COMPLETE SMALL PARTS KIT
You get all 5 Kits shown above plus this handy rack to keep your shop
organized. Kits, Rack and Adjustable Box also sold separately.
Purchase The Complete Shop Parts Kit and SAVE $6594!
Complete Shop Parts Kit GW2006 $294.99
DC0001
DC0004
Small Parts Rack
Adjustable Box
$42.99
$7.99
107
12/22/08
5:03 PM
Page 108
TOOLS – OEM ADAPTORS
OEM
ADAPTORS
BB9007
BB9014
BB9015
TAYLORMADE™ ADAPTORS
Code
Brand
Size
Description
Price Doz. Price Ea.
BB9007
BB9008
BB9009
TM335AD
TM350AD
BB9012
SADW/SADI
BB9003
BB9005
BB9006
CSS
BB9002
BB9013
BB9016
BB9017
PSS
PSSFW
BB9010
BB9012
TaylorMade .370" Fits TaylorMade RAC, HT, LT
& OS Irons
$3.99
$0.35
BB9014 TaylorMade .370" Fits TaylorMade R7 Irons
$3.99
$0.35
BB9015 TaylorMade .350" Fits TaylorMade Rescue Hybrids
$3.99
$0.35
BB9008 TaylorMade .335" Fits TaylorMade R5, R7, Burner &
Super Quad Woods
$2.99
BB9009 TaylorMade .350" Fits TaylorMade R5, R7, Burner &
Super Quad Woods
$2.99
TM335AD TaylorMade .335" Fits TaylorMade Series 500 Woods
$2.99
TM350AD TaylorMade .350" Fits TaylorMade Series 500 Woods
$2.99
BB9012 TaylorMade .335" Enables Lie and face angle change
of TaylorMade R5, R7, Burner &
$11.99
Super Quad Woods
SADW
TaylorMade .335" Fits original woods with .400" bore diameter $0.99
SADI
TaylorMade .370" Fits original Irons with .400" bore diameter
$0.99
CALLAWAY™ ADAPTORS
BB9003
BB9005
BB9006
CSS
Callaway
Callaway
Callaway
Callaway
BB9002
Callaway
BB9013
Callaway
.370"
.335"
.350"
.350"
Fits most Callaway irons
$0.60
Fits older Callaway Drivers & Fairway Woods
$0.60
Fits older Callaway Drivers & Fairway Woods
$0.60
Fits FT-5, FT-I, X-460, Big Bertha 460,
$2.99
& Great Big Bertha II
.335" Fits FT-5, FT-I, X-460, Big Bertha 460,
Big Bertha 454, VFT, ERC II, Steel Head III, &
$2.99
Great Big Bertha II
.335" Enables Lie and face angle change of FT-5,
FT-I, X-460, Big Bertha 460, Big Bertha 454,
$11.99
VFT, ERC II, Steel Head III, & Great Big Bertha II
PING™ ADAPTORS
BB9016
Ping
BB9017
Ping
BB9010
PSS
PSSFW
BB9012
Ping
Ping
Ping
Ping
.335" Fits G5 Drivers, G5 Fairway woods &
G2 Drivers
.350" Fits G5 Drivers, G5 Fairway woods &
G2 Drivers
.335" Fits G2 Fairway woods RH
.335" Fits TISI & TEC i3 Drivers RH
.335" Fits ISI and i3 Fairway woods RH
.335" Enables Lie and face angle change of
G5, G10 & Raptor Drivers
$1.99
$1.99
$4.49
$4.49
$3.99
$11.99
TITLEIST™ ADAPTORS
BB9011
Titleist
BB9021
Titleist
BB9021
BB9011
.335" Replacement Adaptor and Hosel for
905T & 905S
.335" Replacement Adaptor and Hosel for
907 D1 & D2 Drivers
$14.99
$14.99
NIKE™ ADAPTORS
NK0001/NK0002
108
BB9019
BB9020
NK0001
NK0002
BB9019
BB9020
Nike
Nike
Nike
Nike
.350"
.350"
.335"
.335"
Fits Sasquatch Driver - Silver Ring
Fits Sasquatch Driver - All Black
Fits Sasquatch Driver
Fits Sumo Driver
$0.60
$0.60
$0.99
$0.99
12/22/08
5:04 PM
Page 109
FERRULES – TOOLS
New oversized
ferrules can be blended with the hosel by
wiping ferrules with a
rag soaked in acetone
after filing down.
1-quart can.
ACETONE
BRASS ADAPTOR SHIMS
These shims are the perfect answer to your shaft installation
headaches. Easy to use, they center the shaft in the bore
perfectly and create a maximum bond between the shaft and
the hosel.
SHIM-15
$3.99
Fits .335" shafts to
.350" hosels (5 pk.)
SHIM-65
$3.99
SHIM-30
$3.99
SHIMT
$3.99
Fits .355" taper
iron shafts to .370"
(5 pk.)
UNIVERSAL
PLASTIC
SHIM
Universal Plastic Shim
with attached ferrule to
install .335" shafts into a
.350" hosel bore.
BB9018
ECONOMY FERRULE
INSTALLER TOOL
To use the Original Economy Ferrule Installer
Tool, simply start the ferrule onto the shaft and
then tap up the shaft until it reaches the right
measurement. Will
install up to .405"
diameter ferrules.
GW1003
$6.99
$6.99
NOTICE: CANNOT BE
SHIPPED BY AIR.
BUSHING
SHIM
SPLIT
FERRULES
Plastic sleeve with
attached ferrule for
inserting a .335" wood
shaft into a .350" bore.
LE9002
(4 pack)
$ .99
ACTQ
Replace damaged ferrules without removing the
club head. Apply a small amount of epoxy and
snap into place.
LE9003 $3.99 (12 pk)
.370" Irons
LE9004 $1.99 (6 pk.)
.335" Woods
LE9005 $1.99 (6 pk.)
.350" Woods
$2.99
ECONOMY FERRULE
INSTALLER TOOL
WITH NYLON
This ferrule installer tool includes a nylon bushing that
helps to protect the ferrule from damage during installation.
To use, simply start the ferrule onto the shaft and then tap
the ferrule up the shaft, with the nylon end touching the ferrule, until it reaches the correct measurement. Will install
up to .405" diameter ferrules.
GW1004 $9.99
Economy Installer
with Nylon
These pins are specifically designed for finishing graphite and steel shafts used on
bore-through wood heads. Using epoxy, these graphite pins are inserted into the end
of the shaft and sanded smooth to conform to the sole of the head.
This method is efficient and will result in a factory finished look. The Black tip pins
come 25 to a package. Features a nail type head for easier installation.
BORE-THROUGH SHAFT PINS
BTSPG
$4.99
Shaft Pins For Graphite (Woods and Irons)
BTSPS
$4.99
Shaft Pins For Steel (Woods and Irons)
TRUE TEMPER SENSI-CORE INSERTS
Add SensiCore inserts to your irons when you re-grip, re-shaft, or buy a new shaft. SensiCore is a patented technology from True Temper Sports Inc designed
to absorb the vibration of hitting a golf shot. This frequency tuner polymer core eliminates up to 70% of unwanted vibration at impact.
SensiCore dramatically improves feel and provides golfers the ability to practice and play longer because it decreases the harmful effects of "shock" on the
hands, wrists, elbows and shoulders.
Tour professionals have taken SensiCore to the winner's circle over 300
times. They will tell you that SensiCore provides the best feel in golf.
Improve the feel in your irons...your hands, your elbows, and your back.
TTSP
$27.99 8-Pk.
109
12/22/08
5:04 PM
Page 110
TOOLS – EXTENSIONS
UNIVERSAL EXTENSIONS
The Universal Shaft extensions will work with almost any steel or
graphite shaft. After applying a little epoxy, insert the extension into a
shaft, force the provided tapered plug into the extension until the extension expands to fit the ID of the golf shaft. It’s that simple.
GW1047
Package of 3.
$6.99
Will compress to fit a .540" inside diamter (ID) and
expand to fit up to a .590" inside diameter (ID).
STEEL SHAFT BUTT
EXTENSIONS
SEAMLESS INSERTION
Use these steel shaft butt extensions to extend shafts and increase the
length of clubs. The extensions are double length. When cut in two, each
section has an end tapered to fit inside the shaft being extended.
S56
S58
S60
S62
.560"
.580"
.600"
.620"
Butt
Butt
Butt
Butt
Size
Size
Size
Size
$2.59
$2.59
$2.59
$2.59
GRAPHITE WOOD
SHAFT EXTENSIONS
The GolfWorks offers graphite extensions for standard or
ultralite shafts. These 3" extensions are made of injectionmolded graphite for strength and durability. Choose the
extender that fits your shaft. Can be sanded to fit most
graphite shafts.
GSE
USGE
Graphite Shaft Extension (.600")
$1.99
Ultralite Graphite Shaft Extension (.600") $1.99
USGE
.535"
.600"
GSE
.600"
ALUMINUM SHAFT EXTENSIONS
FOR GRAPHITE AND STEEL
These Aluminum Extensions are designed to extend more than one club. They feature a
4" mid-section with reducing ends on both sides. Available in sizes to fit steel and graphite
shaft butts (may require sanding).
ASSE
AGSE
$1.99
$1.99
.480"
Steel
Graphite
Steel Shaft Butt Extensions (.600")/.550" Post Size
Graphite Shaft Butt Extensions (.600")/.480" Post Size
The extensions, made of maple and weighing less than 12 grams, are very strong and durable. Club
length can be extended up to 2" allowing for the longer arc and added distance some players prefer.
These extensions are available for .600" butt diameters only, but can be modified to fit smaller diameters
(instructions included). For larger diameters, like .605", .610" or .620", you will need to build up the
butt end with tape.
MAPLE WOOD SHAFT EXTENSIONS
WBE60 .490" Post Size Extension
LONG AND
BELLY PUTTER
SHAFT
EXTENSIONS
Converts any standard putter shaft
into a belly or long putter shaft.
Each extension measures 11" with
a .530" post size outside diameter
on one end to slide inside the
existing shaft.
Long/Belly Extensions
LE9001
$3.99
110
$2.99
THE GOLFWORKS
EXTENSION ADHESIVE
The GolfWorks new Maximum Strength Extension Adhesive has been designed specifically for securely fastening and sealing graphite, steel, aluminum and wood extensions into golf shafts. The Extension
Adhesive is a very strong, quick setting adhesive that features a slightly thicker viscosity and cures less
brittle than most standard golf club shafting epoxy. The thicker viscosity helps fill the larger voids often
encountered when installing extensions. The more elastic cured hardness helps eliminate the possibility
of brittle shafting epoxy breaking loose inside the shaft and becoming an irritating rattle. The Extension
Adhesive sets up in
approximately 5 minutes and comes in an
easy to use 30ml
syringe.
VB1009 $5.99
30 ml.Syringe
12/22/08
5:05 PM
Page 111
REFINISHING – TOOLS
MULTI-TOOL
POLISHING STATION
The Multi Tool polishing station is an all inclusive tool for iron/wedge
grinding and finishing the bottoms of thru-bore metal woods. The 2" x 36"
belt features a rubber contact wheel positioned well away from the motor
for ample working room. The Multi Tool comes with an installed 6" sisal
wheel that when coupled with the correct compounds, Trizact belts and
Scotchbrite finishing belts will produce a factory mirror finish on those
hard to polish titanium drivers and stainless irons. The 115 volt, 1/3 HP
Jet motor provides 3600 rpm’s of motor speed which equates to over 5,000
rpm’s of belt speed.
MT0007 $349.99
BSC
$8.99 Black Sisal Compound 3lb. 7oz.
WCP
$8.99 White Sisal Compound 3lb. 7oz.
NOTE: ADDITIONAL SHIPPING CHARGES
REQUIRED DUE TO WEIGHT.
2" X 36" MACHINE ABRASIVE BELTS
FOR MULTI-TOOL POLISHING STATION
SCOTCHBRITE
2" X 36" BELTS
NORTON
SANDING
BELTS
High quality Norton sanding
belts ideal for rough iron shaping and surface sanding.
2" x 36". 120, 150 or 220 grit.
NT0001 $6.99
3M TRIZACT
BELTS
Trizact belts are ideal for refinishing
polished or satin titanium wood
heads. Use in combination with
Sisal and Scotchbrite Polishing Belts
for a high polish finish on titanium
woods. 2" x 36". Fine or Super Fine.
MT0005 $8.99
The Scotchbrite 2” x 36” are part of the finishing supplies
needed to complete the Multi-Tool finishing system. The
Medium belt is coarse enough to remove small nicks and
scratches and can do some moderate shaping. The Fine belt
produces a quality brushed satin finish on any type of
metal. The white polishing belt along with white rouge will
produce a mirror finish on titanium and stainless steel when
prepped with a sisal wheel.
MT0004 $24.99 Medium (Red)
$24.99 Fine (Blue)
MT0006 $18.99 Polish (White)
MEDIUM
FINE
POLISH
FINISHING & DEBURRING WHEELS
FOR BALDOR® MULTI-TOOL POLISHING STATION
3M NYLON
3M CPM
FINISHING WHEEL DEBURRING
Nylon wheel for removing
WHEEL
surface scratches from metal
woods and
irons or
from
soleplates.
Works
well for
stripping
finishes.
Great for
general cleaning
and polishing. Specify Fine or
Medium.
Fine Wheel
NYW
$34.99
Med. Wheel
NYW
$34.99
Aluminum oxide wheel removes
deep nicks and
scratches from
metal surfaces. Also
cleans,
deburrs,
blends and
finishes all
types of metals and composites. Great for grinding graphite
tips from bore-through heads.
Works best at 3,450 rpm.
CPMW $99.99
BUFFING WHEEL
RAKE
Renews buffing wheels after extended use. Hold
rake against spinning wheel. In seconds the surface is unclogged and ready to use again. Works
for stitched and unstitched buffing wheels. Also
great to break in new wheels. Replacement teeth
available.
Rake
BUFR $24.99
Replacement Teeth BUFT $9.99
3M SCOTCHBRITE
EXL DEBURRING
& FINISHING
WHEEL
A must for all
shops! Specially
designed
Scotchbrite
wheel used
for blending,
initial deburring or sanding
scratches. Works
best at 3,450 rpm
EXLM
$64.99
Specifically treated 6" Sisal Wheel and an
improved 6" buffing wheel complete the MultiTool finishing system. Use of these wheels
with the correct compounds and
the Scotchbrite finishing belt
allows a mirror finish to be
easily applied to steel and
titanium club heads.
A
6" SISAL WHEEL
A. 6" Stitched Buffing
Wheel
– 1/2" Arbor
DB0001 $4.99
B
B. 6" Treated Sisal Wheel
– 1/2" Arbor
FS0001 $24.99
NOTE: Wheels are 1" x 6" with a 1" center opening. Each wheel includes an adaptor
to fit 1/2", 5/8", 3/4" and 7/8" arbors.
ADA Extra Adaptor $6.99 ea.
MULTI PURPOSE
FINISHING BLOCK
Grit embedded rubber block is an excellent tool
for removing minor scratches from stainless steel
heads or cleaning up the face of a sandblasted
iron. Simply use the block like an eraser, rubbing
firmly over the surface. Stays abrasive as the
block wears. Easy to use. 3" x 1" x 5/8".
MPFB $5.99
FOUR BAR
BUFFING SET
Set includes four bars: Emery Cake for fast,
sharp cutting. Tripoli Brown Rouge for buffing softer metals and plastics. Red Rouge for
buffing all metals to high luster. White
Rouge for the finest polish on stainless steel
and most other metals
and plastics. Use
with our Stitched
Buffing Wheel.
Each bar
weighs 4 oz.
Set of 4
BC4
$9.99
111
12/23/08
10:03 AM
Page 112
TOOLS – SHAFT PREPPING
1" X 30" BELT
SANDER/
SHAFT
CUTTER
GOLFWORKS
INDUSTRIAL
SHAFT CUT-OFF
MACHINE
A fast and compact way to
cut steel and graphite
shafts. The 4.5" cutoff
wheel is powered
by a 10,000 rpm
angle grinder
motor that will
not hesitate or
slow down when
cutting shafts. A
formed steel base
has an internal shaft tip
catch pan and an attached
7.5" tipping ruler to eliminate the
need to pre-mark the amount of shaft
being cut. An optional foot pedal is available for ease of use and “hands free” cutting.
The GolfWorks 1" x 30" Belt Sander/Cut-Off Wheel
provides everything needed to do professional shaft
cutting, shaft prepping and ferrule turning. The 110v,
1/3 HP 3400 rpm motor provides plenty of power and
durability for the most demanding club makers. The
attached ferrule turning arm holds the golf club
very securely, making turning ferrules easy for
even a beginning club maker. A ruler has been
added to the shaft cutting table to eliminate the
need to pre-mark shafts before cutting. An
optional foot pedal is available to really speed
up and simplify the assembly process. This all
inclusive unit performs as well if not better than similar machines at almost
half their price.
GW1032
Industrial Shaft Cut-Off Machine
$179.99
GW1044 Foot Pedal for GW1032
$ 34.99
GW1038 4.5" Replacement
$4.99
Cut-Off Wheel
NOTE: ADDITIONAL SHIPPING
CHARGES REQUIRED DUE TO
WEIGHT.
GW1046
1" x 30" Belt Sander/Cut-Off Machine
$129.99
GW1044
Electric Foot Pedal $34.99
GOLFWORKS
CUT-OFF
SAW
The GolfWorks High Speed Cut-Off machine will easily cut any
graphite or steel shaft. The base plate features an adjustable
guide that allows pre-cut angles on a shaft for a through-bore
wood or ironhead. The GolfWorks High Speed Cut-Off
Machine is portable and does not need to be mounted to a bench.
Portable and lightweight. Uses 6" wheels. 110 VAC.
CSM6
GolfWorks Cut-Off Saw
$39.99
CSM6RW
Replacement 6" Cut-Off Wheel $ 4.99
WEIGHT.
GOLF SHAFT CUTTER
This handy cutter comes with a hardened,
tempered cutting wheel for steel shafts.
An optional wheel for
graphite shafts is
available!
Cuts Graphite Shafts!
STC
STCW
STCWG
112
This 12" grit edged blade mounts in a hacksaw and cuts graphite or
fiber-type shafts without fraying. Also cuts any insert material. A
great alternative to fraying an expensive graphite shaft!
GRIT EDGE BLADE
GREB
Golf Shaft Cutter
Replacement Wheel for Steel Shafts
Replacement Wheel for Graphite Shafts
Grit Edge Blade $4.99
$9.99
$2.45
$4.99
12/23/08
10:04 AM
Page 113
SHAFT PREPPING – TOOLS
1"X 42" PROFESSIONAL
BELT SANDING MACHINE
This 1" x 42" belt model is ideal for turning ferrules and
roughing shaft tips. A professional grade sander, made from
heavy gauge steel with a steel base and suction cups to keep
it in place during operation.
The Professional Belt Sanding Machine has 1/2" arbors and
comes with a 1/3 hp, 1,725 rpm, 6.2 amp electric motor
wired with a plug for a standard outlet. Medium sanding
belts are included. Other belts available
are listed on this page.
GW1105 $189.99
WEIGHT.
1" X 42" BELT SANDER/
CUT OFF WHEEL
The GolfWorks industrial 1" x 42" belt sander plus cut off wheel
will handle all of your shaft cutting and prepping needs. Abrasive
cut off wheel quickly cuts both steel and graphite shafts. 1" x 42"
belt can be equipped with a Norax belt (below) for safely prepping
graphite shafts and a 1" x 42" linen belt for turning ferrules. Spring
loaded belt assembly allows for quick belt changing. Belt sander
attachment and ferrule turning arm also sold separately.
• 6" x 1/2" Abrasive
Cut-Off Wheel
(Included)
• 110 AC Power Cord
• 1/3 HP Baldor Motor
• 1/2" Double Arbor
• 3000 RPM
Optional Ferrule Turning Arm
GW1021 $329.99
Belt Sander/Cut
Off Wheel with Motor
DELUXE FERRULE
TURNING ARM
Mount this arm next to your belt sander
and make turning ferrules a snap! Arm
cradles the shaft to avoid scratching and
has an adjustable height so it will work
with virtually any sander.
GW1025 $29.99
Ferrule Turning Arm
For GW1021
GW1022 $149.99
Belt Sanding Attachment Only
ACOW $4.99
Replacement Cutoff Wheel
GW1104 $34.99
MACHINE ABRASIVE BELTS
The GolfWorks Belt Sander uses popular
1" x 30" belts, ideal for the small volume
shop or hobbyist that can’t justify the
1" x 42" machines costing hundreds more.
This Belt Sander is perfect for abrading
steel shaft tips and removing polyurethane
coating from graphite shaft tips before
reshafting heads. Features a tilting work
table that makes it easy to set the angle
for grinding off through-bore shaft tips
perfectly every time. Also features a
dust collection outlet for connection to a dust control vacuum
system — a big plus considering
the dust shaft prep work creates! 1/4 hp,
2 amp, 110 VAC, 60 Hz motor runs at
3,450 rpm. Includes one belt. Extra belts
available on this page.
GOLFWORKS BELT SANDER
NOTE: ADDITIONAL
SHIPPING CHARGES
REQUIRED DUE TO
WEIGHT.
Ideal for removing the polyurethane coating from graphite shaft tips
without cutting fibers. 1" by 42".
NOR42
1" x 42" belt $6.25
NORAX BELT
Safely remove paint from graphite shafts without cutting fibers.
M130B
1" x 30" belt $3.49
M142B
1" x 42" belt $3.49
MICRO GRIT BELTS
Available in choice of three grits - coarse, medium or fine. Great for
steel shaft prep.
SANDING BELTS
SB3(C,M,F) 1" x 30" belt $2.75
BEL(C,M,F) 1" x 42" belt $2.75
IVS3C $69.99
ECONOMY
FERRULE
TURNING ARM
Designed expressly for use with
the GolfWorks Belt Sander
IVS3C (above). Just mount next
to your sander, and the height is a
perfect match for the belt. Safely
and controllably turn ferrules.
EFTA
$19.99
White linen belts are what manufacturers use to turn down ferrules without
scratching the shaft or head. Blend ferrules perfectly!
LINEN FERRULE TURNING BELTS
PF30B 1" x 30" belt $3.99
PFTB 1" x 42" belt $3.99
PFT3B 2" x 30" belt $3.99
Slightly more abrasive than traditional linen, these belts produce a fast and
professional finish. 1" by 30" or 42". Also available in 6" width that can be
trimmed to custom widths.
BF130 1" x 30" belt $2.99
BF142 1" x 42" belt $2.99
BF630 6" x 30" belt $3.99
BF642 6" x 42" belt $3.99
INDUSTRIAL FERRULE TURNING BELTS
HANDHELD SHAFT
DIMPLER
HHSD $24.99
Handheld Shaft
Dimpler
RSSD $1.99
4 Replacement Set Screws
113
12/23/08
10:05 AM
Page 114
TOOLS – VISE
UNIVERSAL
VISE
Made from unbreakable steel. Torque handle included. Now
also includes Standard Clubmakers Vise Jaws (as shown)
and dovetails needed for use with Multi-Purpose Jaw Set
and Universal Vise Extractor listed below.
UCMV $99.99
Optional base allows vise to be extended 12" from workbench! Great for gripping and
extending your workspace. Allows you to work "around" your vise!
VISE EXTENSION
UCMVEX
$49.99
1
2
3
4
A complete set of hold-tight jaws that will secure the shaft no matter what clubmaking or repair task you are performing. Set includes:
1. LOCK-TITE SHAFT REMOVER
Ideal for removing stubborn steel shafts from woods and irons. Constant 4"
clamp pressure holds the shaft in place while applying pressure against it.
MULTI-PURPOSE JAW SET
2. STEEL SHAFT DIMPLER
Dimpling is the preferred method for creating a solid bond between a steel shaft
and a clubhead. This dimple attachment allows you to do the job in just seconds!
3. GRAPHITE SHAFT PADS
These soft pads are ideal for gripping, shaft tip abrasion or other graphite shaft
assembly or repair tasks. Will hold the shaft in a horizontal or vertical position
without marring.
SHAFT
EXTRACTOR
Accommodates all shaft sizes. Secure the
shaft between the Shaft Extractor pads
with the hosel positioned in the
appropriate holder.
Attach the ratchet to
the other side and
glide the head off
the shaft tip! A
constant 4" of clamp
pressure prevents
slippage.
UCMVGSR
4. GRIPPING PADS
Soft pads to protect the shaft, yet their 4" length grips the club firmly, allowing
you to quickly and easily remove an old grip and install a new one.
UCMVJWS Multi-Purpose Jaw Set $59.99
$79.99
SOLVENT
CATCH PAN
No more grip solvent splattering on the workbench and the
floor! Solvent catch pan easily
mounts to any workbench.
UCMVGP
114
$14.99
12/23/08
10:06 AM
Page 115
VISE ACCESSORIES – TOOLS
UNIVERSAL CLUBMAKERS
VISE SYSTEM The Ultimate Clubmaking Workbench Tool Set!
Start with a superb steel vise, with a universal jaw attachment system, add
multiple sets of interchangeable jaws and clamps, a graphite shaft extractor designed for this vise, and a solvent catch pan for regripping. Then we
add our unique Vise Extension for better access to your work or to attach
the solvent catch pan as well as set the vise higher off the workbench to
reduce bending when working.
NOTE: ADDITIONAL
SHIPPING
CHARGES
REQUIRED DUE TO
WEIGHT.
FEATURES:
•
•
•
•
•
•
UCMV Universal Vise
UCMVEX Vise Extension
UCMVJWS Sets of Jaws (4)
UCMVGSR Graphite Shaft Extractor
UCMVGP Solvent Catch Pan
UCMVSJ Standard Jaws (included)
$99.99
$49.99
$59.99
$79.99
$14.99
UCMVK Complete Kit
$259.99 SAVE $4496
PRO LEVERACTION SHAFT
HOLDER
Quick and secure clamping during regripping. Features a unique
clamp that holds the shaft on
three sides. Pro Lever-Action
designed to engage quickly.
Includes rubber pads.
PASH
$69.99
SHAFT VISE
CLAMP
This clamp is an absolute necessity
for regripping, assembling clubs and
reshafting. It slips over the shaft and
is placed in the vise to hold the shaft
or club securely without crushing or
marring it. This vise clamp holds
better and will last longer than any
rubber type vise clamp on the market! Made of synthetic material with
ribbed sides, it is 31/2" long. Can be
used with graphite shafts.
RSC
ALUMINUMBRASS
VISE PAD KIT
Aluminum pads are ideal for protecting ironheads held in a vise. Fits all
vises. Brass pads are used to secure
irons and putters in the vise. Brass
pads are softer than head materials,
permitting you to tighten more
securely than with other pads.
ABVK
$8.99
This durable, heavy duty professional shaft clamp is easy to use.
Made of heavy gauge steel on
the outside and vulcanized rubber on the inside, it's a must for
every shop. NOTE: Can be used
with graphite shafts.
EMSC
DELUXE HEAVY
DUTY
SHAFT CLAMP
Slightly firmer clamping material
than the Professional Metal Sided
Shaft Clamp below. Provides
extra firm grip and offers lasting
durability.
DRSC
$9.99
$8.99
$1.99
RUBBER VISE
PAD
Vertical and horizontal grooves in
each pad help to hold shafts, highlofted woods and hard-to-secure
heads.
UVP
PROFESSIONAL
METAL SIDED
SHAFT CLAMP
$12.99
ORIGINAL LOCK
TIGHT SHAFT
HOLDER
Original Lock Tight Shaft Holder
holds steel shafts securely for wood
or ironhead removal. Assorted hole
sizes accommodate standard steel
shafts. Soft alloy will not mar steel
shafts.
TSL
$17.99
SUPER LOCK
TIGHT SHAFT
HOLDER
A heavy-duty version of the
Original Lock Tight with
lengthened clamping surface for
added gripping power. Bottom
hinge designed to speed shaft
removal. Three different diameter
channels to fit all modern steel
wood/iron shafts. NOTE: Not for
graphite shafts.
STSL
$29.99
115
1/5/09
12:03 PM
Page 116
TOOLS – SHAFT REMOVAL
NOTE:
ADDITIONAL
SHIPPING
CHARGES
REQUIRED
DUE TO
WEIGHT.
FAST SHAFT
EXTRACTOR
Designed for the high-volume club repair shop. After applying heat to the clubhead, the 22" leverage bar exerts tremendous pressure, rapidly compromising the
epoxy bond. The 4" coated jaws securely clamp stubborn shafts while heat and
constant pressure are applied. Heavy duty, bench mount construction. Complete
with mounting bolts and instructions.
FASTE
$249.99
Replacement Pads
FASRP
$14.99
Graphite Shaft Extractor
MA2007 $149.99
NOTE:
ADDITIONAL
SHIPPING
CHARGES
REQUIRED
DUE TO
WEIGHT.
Note: Not recommended for
graphite or wooden heads.
Improve efficiency and reduce the damage to shafts
and heads. The Enhanced Graphite Shaft Extractor is
designed with an internal load sensing spring and indicator. To use, place the club into the device and tighten as you would any screw-type extractor. Tighten
until the indicator shows the spring is loaded. Then
apply heat. The pressure exerted by the spring is
enough to cause the head to slide off once the epoxy
breaks down from the heat, but not so much spring
pressure that the head shoots off!
Your hands remain free, as you don't have to feed
pressure while the head starts to move. Can be
mounted to workbench or used in a vise.
GW1009 $189.99
Graphite Shaft
Extractor
RBW
$4.99
Ratchet
Box
Wrench
(included)
Quickly and conveniently remove graphite shafts. Simply heat the hosel and pry off the clubhead.
Quick, but takes practice.
GRAPHITE SHAFT EXTRACTOR BAR
GSRT $14.99
116
A handy little
tool to easily
remove graphite shafts
broken off at the hosel
of wood and iron heads.
Drill a pilot hole using
a 7/32" drill bit and
screw in the Broken
Graphite Shaft
Extractor. Place the
Broken Graphite
Shaft Extractor into
any Graphite Shaft
Extractor for easy
shaft tip removal
(see below).
GW0025
$9.99
Loading clubs and unloading shafts is quick and easy
with the speed handle. Rubber coated pads ensure
shafts are not damaged. Pressure is applied using a
ratchet box wrench to turn the threaded rod - the shaft
is not twisted. Vise mounted for stability.
GRAPHITE
SHAFT
EXTRACTOR
ENHANCED
GRAPHITE SHAFT
EXTRACTOR
GOLFWORKS
BROKEN
GRAPHITE
SHAFT
EXTRACTOR
VALUE SHAFT
EXTRACTOR
Shaft saver clamp fits in most standard bench top vises (vise not
included). Simply secure the shaft
between the rubber Shaft Extractor
pads with the hosel positioned in
the appropriate holder. Attach the
ratchet to the long bolt on the
opposite side, apply heat and glide
the head off the shaft tip. Straight
push with no twisting saves
graphite shafts for re-use.
GW1112
$69.99
ALUMINUM
HOSEL
PROTECTOR
Prevents damage to hosels when
pulling heads from shafts. Place
Hosel Protector between shaft
remover and hosel, the soft aluminum Hosel Protector
cushions as the
head it is pushed
off the shaft.
GW1113
$7.99
12/23/08
10:08 AM
Page 117
SHAFT REMOVAL – TOOLS
ECONOMY ELECTRIC
HEAT GUN KIT
CLUB SHIELD
Club Shield is a safe,
non-toxic paste or gel that
safeguards vital parts of the
golf club during repairs
when heat is required.
Preserves and protects:
• Painted finishes
• Ferrules
• Graphite shaft finishes
Without
• Putter inserts
Club
The GolfWorks Tech Staff
Shield
literally gave Club Shield a
"trial under fire" by coating the
hosel, ferrule and crown of a
driver with this solution and directly
applying heat. The results were
incredible! Cleans away easily with
just the wipe of a cloth.
GW1039 16 oz. Paste $10.99
HSG
Pint bottle $11.99
GW1033 2 oz. bottle
$3.99
Beat The Heat!
A great value! Complete kit for slow heating clubs for shaft
extraction. Two temperature settings — 630° F and 1,000° F.
Sold complete in kit form with
heat gun, putty knife, one wood
handle and three scrapers, four
heat gun nozzles and case.
EHGK
FERRULE GUARD
FOR PING WOODS
One-touch ignition makes it easy to light. Refillable
using butane lighter fluid available at most grocery stores. Adjustable
flame burns to 2,450° F. Includes its own stand for hands-free operation
and safe, upright storage. 4" tall.
PRO TORCH
LPT200 Torch
$29.99
LBFB
Butane Fuel Cylinder $3.99
$29.99
With
Club
Shield
For use with Ping wood models with hosel sleeve
(TiSi and TEC models). Hard, nylon sleeve allows
the head and the hosel sleeve to be pushed off the
shaft without damage to either part. Works on
.335 or .350 shafts.
NOTICE: LBFB CANNOT
BE SHIPPED BY AIR.
GW1115 $13.99
Precision orifice controls and concentrates heat exactly where it is
needed. Provides the heating power of a propane torch — blue flame temperature up to 2,500° F (1,350° C). Butane fuel cylinders sold separately.
Burns 200 minutes on each filling.
PRO PLUS TORCH
LPT500 Pro-Torch
$54.99
LBFB
Butane Fuel Cylinder $3.99
NOTICE: LBFB CANNOT
BE SHIPPED BY AIR.
Protect the painted finish on no-hosel metal woods! Simply place the Paint
Saver tool between the head and the shaft remover
tool. Beveled leading edge of the tool fits the hosel
opening precisely and prevents damage to paint.
Works on .335 or .350 hosel bores.
WOOD PAINT SAVER
GW1002 $9.99
THIRD HAND HEAT
GUN HOLDER
Developed in our Total Golf Club Repair School. Now
you can heat a hosel and shaft while you perform other repairs.
Wide, heavy duty clamping fixture is attached to a swivel neck
mounted to a 7 lb. base, so it will not tip over.
CAUTION: NEVER leave a heat gun unattended.
HGH
$49.99
FERRULE
SPLITTER
Simply place the Ferrule Splitter between the shaft
extracting tool and the ferrule and, as pressure is
applied, the splitter cuts through the ferrule without damaging the shaft. Works
especially well on ferrules that have
been epoxied onto the shaft.
GW1001 $6.99
PASTE METAL
POLISH/BLUING
REMOVER
Flitz Paste Metal Polish is a
concentrated cream that is
unequaled in its ability to clean,
polish, deoxidize and protect
your golf clubs. Works on all
clubs. Removes: rust, water
stains, heat discoloration, grass
stains, and tee or lie board
streaks. Non-Abrasive Formula.
Non-Toxic. 1.76 oz. tube.
Just rub a little on iron or
metal wood hosels that
have been discolored by the
high temperatures of shaft
removal and the head is
back to normal. 2.5 oz.
BLUE AWAY™
BLAW
$11.99
SIMICHROME
POLISH
Removes the bluing from hosels discolored
during reshafting. Polishes and removes
scratches from chrome, aluminum, silver,
brass and plexiglass. Nontoxic.
50 gram tube.
SIMI
$7.99
NOTICE: CANNOT BE
SHIPPED BY AIR.
FPMP $9.99
NOTICE: CANNOT BE
SHIPPED BY AIR.
117
12/23/08
10:09 AM
Page 118
TOOLS – SHAFT REMOVAL
GOLFWORKS HOSEL CLEANING SYSTEM
The GolfWorks new hosel cleaning system is ideal for all hosel cleaning necessities. The long
stemmed industrial brushes easily clean standard hosels. The extended 4” stem length works much
better on thru-bore hosels than standard hosel cleaning brushes. The brush sizes have been specifically designed for modern club head bore sizes (.335”, .350” & .370”) which increases the life and
durability of the brushes. Soaking the industrial strength cotton swab hosel brushes in acetone or
mineral spirits and inserting into the club head hosels will clean out any oil or epoxy residue that
may negatively affect the new epoxy bond during assembly. All brushes are threaded and can be
used with the same universal wooden handle.
GW1054
$14.99
GW1055
Kit: Includes Handle, 3 wire, 2 cotton brushes
Individual Tools Description
GW1055
Handle for GW Hosel brushes
GW1056 (I370) .370 (W350) .350 (W335).335 Long Stem Wire Brush
GW1057 (I) Irons (W) Woods Hosel Cleaning Cotton Brush
Price
$2.99
$3.99
$1.99
GW1056
GW1057
WIRE HOSEL
CLEANING BITS
The Hosel Bore Gauge measures shaft
diameter and hosel bore for .335",
.350", .355" tapered, .390" and .410"
shafts or hosels. Simply insert the shaft
in the Gauge or place the clubhead
hosel over a post on the Gauge to determine size.
HOSEL BORE GAUGE
HBG
For Hand
Held Drills
$39.99
MULTI GOLF
SHAFT ID GAUGE
A must have tool for reshafting and identifying almost
any shaft. The Multi Golf Shaft Identification Gauge:
• Measures tip diameter of any shaft
• Determines if tip is parallel or tapered
• Identify shaft brand by measuring step
lengths and reading chart printed on the
gauge
• Shows how much to trim for an
in-between flex
• Includes a drill bit reference chart for
opening up hosels after tip trimming a taper
tip shaft
• Heavy aluminum with etched markings.
GSITG
HOSEL
HONING
TOOLS
Great product for cleaning the
inside of a hosel. It is also
excellent for removing epoxy
resin and abrading the inside of
a hosel prior to reshafting.
GW1061 $8.99 each
Avail. .335" woods - green
.350" woods - green
.370" irons - black
$11.99
The easiest way to clean
out hosels. For use with all
drills. Cleans out hosels
quickly and easily and prepares them for re-assembly.
We recommend that the
hosel be cleaned out using
a cotton swab dampened
with solvent after use.
GW1060 .370" $4.99 ea.
GW1060 .335" $4.99 ea.
BRASS ADAPTOR
SHIMS
The perfect answer to your shaft installation headaches.
Easy to use, they center the shaft in the bore perfectly
and create a tight bond between the shaft and the hosel.
SHIM15 $3.99
Fits .335" shafts
to .350" hosels
(5 pk.)
SHIM65 $3.99
Fits .335" shafts
to .400" hosels
(5 pk.)
SHIM30 $3.99
Fits .370" shafts
to .400" hosels
(5 pk.)
SHIMT
$3.99
Fits .355" taper iron shafts to .370" hosels (5 pk.)
Digital Calipers with large LED display is a must-have
for any shop. Makes measuring bore depths, face heights,
quick and easy.
GDC $34.99
DIGITAL DIAL CALIPER
118
12/23/08
10:09 AM
Page 119
SHAFT REMOVAL – TOOLS
PRO DRILL
KIT
SELF-CENTERING
SHAFT TIP
CLEANER
The ultimate cordless hand drill
for a variety of tasks around the
shop. 18-volt motor provides plenty
of power. Chuck accommodates
most bit sizes. Completely
rechargeable.
GW0046 Drill
GW0047 Extra battery
To reuse a graphite shaft, the old epoxy in the
tip must be bored out. Mount the chuck on
the tip of the shaft. Clamp the shaft into
the vise. The chuck acts as a guide for a
1
/8" drill bit used to drill out old epoxy
without damaging the shaft and attaches
securely to a wide variety of shaft sizes.
1
/8" drill bit included.
$39.99
$19.99
GW1110 $29.99
DRILL BIT SET
WITH
HOLDER
A set of the most commonly used drill bits
complete with a sturdy holder conveniently
marked with each bit size.
DBH
REAMING
AND
BORING
VISE
Hold heads for reaming or
boring with the non-marring aluminum clamping jaws. 3/4" jaws for short
or long hosels. Club rests against the protective nylon back plate. Fully adjustable
to fit any hosel size. Bolts directly to your
drill press.
$79.99
Individual drill bits
available at
www.golfworks.com
RBV
BROKEN
SCREW/
SHAFT
EXTRACTOR
SET
COUNTERSINK
& DEBURRING
BALL
Deburring Ball and 18º Countersink bevel the edges of hosels,
removing rough edges and
creating a gap for a cushion of
epoxy to fill. Greatly reduces
graphite shaft breakage! The
Countersink is available in
carbon steel or super
durable carbide. Use for both
irons and metal woods.
18° Carbide Deburring Ball
(7/16" dia. x 3/8" flute)
18DB
18DB $29.99
This set of five extractors will remove
broken shafts from hosels to extracting
soleplate or insert screws. Set can be used
with the Extractor Wrench (GW1108).
35P5
Set of 5 $9.99
GW1108 Handle $6.99
5/32"
diameter rod fits down a graphite shaft.
Perfect for packing lead down a shaft or removing
a stubborn head. Fits through a grip vent hole to
tighten or remove loose tip weights. High-strength
steel with a wooden handle.
RR
$14.99
For Graphite Shafts!
METAL
WOOD
BORE
PLUGS
Serves as a replacement
for manufacturer's plugs.
Prevents epoxy from
working into the clubhead, causing rattles.
MWHBP $4.99
Package of 20
Designed to remove a steel shaft broken below the top of the
hosel. To use, thread the extractor into the broken
shaft, attach the extracting bushing and nut,
apply heat and begin extracting. Available for
woods, irons or as a set.
GW1106 Irons
$20.99
GW1107 Woods $20.99
GW1108 Handle $ 6.99 GW1109 Kit
$44.99
FAST EXTRACT
18CS
18° Carbon Steel Countersink
(5/8" head dia. x 7/8" flute)
18CS $29.99
A. 441/2" RAM ROD
$69.99
B. HEAVY DUTY
421/2" RAM ROD
1
/4" rod is ideal for driving off stubborn ironheads, applying heat inside a shaft tip to loosen
woodheads, or tightening loose tip weights.
Cold rolled steel with a vinyl handle.
RR7
$14.99
3/16" rod is ideal for driving off stubborn ironheads, applying heat inside a shaft tip to loosen
woodheads, or tightening loose tip weights.
High-strength steel with wooden handle.
HRD48 $6.99
C. 48" HEATING ROD
A
B
C
119
12/23/08
10:10 AM
Page 120
TOOLS – SHOP SUPPLIES
GOLFWORKS
REGROOVING TOOL
Deepen or restore worn scoring lines with the The Golfworks Face
Line Cutter. The cutting tip is a coated carbite lathe cutting tool used
in machining. This tool is perfectly suited for for regrooving.
Regrooves all metals commonly used in iron manufacturing.
Also great for cleaning out the scoring lines.
GW1111 $25.99
SCORING LINE
DEPTH GAUGE
A
B
A
IRON RESCORING
NEST
Designed to hold an ironhead securely for
rescoring the face lines. A 3" x 4 3/8" x 1 1/2"
deep steel box filled with plastic covered mortite
putty acts as a soft nest to support the head. A
1/2" cold chisel, sharpened to the proper angle to
deepen scoring lines, is included. Simply press
the back of the iron down into the mortite until
the clamp can secure its toe. Tighten the knob
on the clamp. Carefully align the chisel into a
scoring line and strike with a hammer to deepen.
Complete instructions included.
IRN
$49.99
/2" cold chisel, sharpened to the proper angle
to deepen scoring lines.
2070
$14.99
B
1
CHISEL
New oversized ferrules can be
blended with the hosel by
wiping ferrules with a rag
soaked in acetone after filing
down. 1-quart can.
ACETONE
ACTQ
Repair worn V-groove
scoring lines quickly
and easily with this
special tool and regain
spin. Hard carbide tip
does a neat job.
Note: Rechroming
necessary after use on
plated heads to prevent rust from forming.
RESCORING TOOL
SRT
$10.99
FLDG
Convenient plunger holds acetone
and grip cleaning solvent safely in your
shop. Easily dispenses
the desired amount of
solvent onto a cloth or
paper towel.
A handy tool
used in large
number of
professional
clubmaker's
shops.
PLUNGER CAN
GW1026
$42.99
GOLFWORKS
FACELINE
SCORING PAINT
A high-quality paint that applies easily
with its own brush-in-cap. So quick and
convenient it will save time and money.
Specify color. Available in 4 oz. cans
(Gold in 2 oz. jars).
120
$4.99
$4.99
$4.99
$4.99
$59.99
A fast and easy way to refill scorelines or other
engraved areas on any golf club. Available in
Fine Line and Micro Fine in Red, Black, White
and new colors Yellow and Blue.
MKF-BLK
$3.99
Fine Line Black
MKF-WHT
$3.99
Fine Line White
MKF-RED
$3.99
Fine Line Red
MKF-BLU
$3.99
Fine Line Blue
MKF-YEL
$3.99
Fine Line Yellow
MKM-BLK
$3.99
Micro Tip Black
MKM-WHT
$3.99
Micro Tip White
MKM-RED
$3.99
Micro Tip Red
MKM-YEL
$3.99
Micro Tip Yellow
PRO LINE PAINT PENS
$6.99
FINE
TIP
NOTICE: CANNOT BE
SHIPPED BY AIR.
FLBK
FLPW
FLPR
FLPG
The GolfWorks Repair Department has measured tens of thousands of scoring lines on irons
and wedges, including hundreds belonging to
PGA Tour players. Often
the lines are too shallow
due to wear or manufacturing. Scoring lines
less than the USGA
allowed .020” generate less than optimal
backspin, reducing
control and consistency. Use the
Rescoring Tool
(SRT) to renew
the lines or send
the heads to us for
regrooving.
Black
White
Red
Gold
LACQUERSTIKS
Lacquer-Stiks will work
well on any stamped,
carved, engraved lines
or lettering on metals,
glass, ceramic, plastics
and wood. Use to fill
iron and soleplate
stampings. Sold
separately
or as a set of 5.
LQ-BLK
LQ-RED
LQ-WHT
LQ-GLD
Black
Red
White
Gold
$3.99 ea.
NOTICE: CANNOT BE
SHIPPED BY AIR.
MICRO
TIP
PAINTFILL
BOTTLES
This bottle dispenses
small amounts of paint
through a needle tip into
fine engraving. Paint not
included. 1 oz.
PBT
$2.49
1/6/09
10:30 AM
Page 121
SHOP SUPPLIES – TOOLS
CLUB CONEX
4-PLAY
4-PLAY DETAILS
Hosel
Shaft
Club-Conex interchangeable adapters
Hosel RH/LH
Adaptor Adaptor
will provide golfers of every skill level
Size
$14.50
$13.50
with the instant feedback they desire
0.335" RH/LH
CC0011
CC0013
when they are testing the performance
0.350" RH/LH
CC0012
CC0014
A
differences between various heads and
shafts. The Club-Conex 4-PLAY and
FAZ-FIT adapters are sold individually allowing you to select the style of club head and
shaft you wish to make interchangeable.
New from Club-Conex, the 4-PLAY interchangeable adaptors allow 100% interchangeability between your
favorite wood heads and shafts and are now USGA conforming. The 4-PLAY adaptors are easy to install and allow
you to create your interchangeable golf club at a fraction of the cost of O.E.M. interchangeable drivers.
Allow The GolfWorks professional assembly team to custom build an interchangeable club for you! The GolfWorks
will professionally assemble the 4-PLAY head and shaft adaptors into any head or shaft combination(s) in our
catalog. Just pick your head(s), shafts(s) and grip(s), provide us with your specs and we will do the rest.
4-PLAY Hosel Adaptor Assembly $19.99
(Includes 4-PLAY Hosel Adaptor)
CC0015 $15.00 Shaft
Installation Tool Wrench
CC0016 $8.50 Hosel
Adaptor Installation Tool
B
4-PLAY Shaft Adaptor Assembly $17.99
(Includes 4-PLAY Shaft Adaptor and grip installation)
CALL FOR DETAILS 1-800-848-8358
FAZ-FIT
FAZ-FIT adapters, designed for club fitting professionals, can be
installed into just about any type of club head or shaft in just a few
easy steps. Just imagine, with only (10) club heads and (10) shafts
utilizing FAZ-FIT interchangeable adapters you will have the
equivalent of one hundred different club configurations.
Both Club-Conex Interchangeable Adaptors work with RH &
LH Clubheads.
A
B
Shaft
Adaptor
$10.70
CC0004
CC0005
CC0006
Hosel
Size
RH/LH
Hosel
Adaptor
0.335"
0.350"
0.370"
RH/LH
RH/LH
RH/LH
$11.30
CC0001
CC0002
CC0003
* Wrench and Grip(s)
Sold Separately
A
CC0007 $16.60 Installation Tool Wrench
B
GRIP ™
MAGIC
This revolutionary grip-cleaning
solvent works wonders on all
types of grips. Simply put Grip
Magic liberally on a towel or
cloth and apply to the surface of
your grips.
Grip Magic dries instantly and
restores the tacky, new grip feeling players want.
100% water based and
environmentally safe.
GOLF SHOP
REPAIR TAGS
Use these handy two part Repair Tags to
keep track of your customers’ clubs. Set of
100 tags comes in numerical sequence.
RET Pkg. of 100
$8.99
PROFESSIONAL
REFINISHING
TAPE
The best masking tape for refinishing heads! 3M
Masking Tape is used to mask off polished areas
during sandblasting. Does not lift under pressure.
Available in (specify size) 1/8", 1/4" and 1/2" widths
in 60-yard rolls.
3M specify width $3.99
GPMG $7.99
PROTECTIVE
GLASSES
Always wear safety glasses when trimming a
shaft! These are popular, nylon framed glasses
with side shields. Extremely comfortable for
regular wear.
FEG
$4.99
LEATHER
BUFFING
GLOVES
These American-made,
commercial grade
leather gloves are a
must when handling
hot iron heads during
reshafting.
One size fits all.
LGLO
$12.99
ALUMINUM OXIDE
BLASTING SAND
The proper mix of sand for blasting metal wood
and iron faces to make them look like new.
Reusable. Note: Sandblasting a chromed iron
face is NOT recommended
as rusting will most likely
occur.
NOTE: ADDITIONAL
AOBX
SHIPPING CHARGES
$14.99
10-lb. Bag REQUIRED DUE
TO WEIGHT.
121
12/23/08
10:12 AM
Page 122
TOOLS – KITS
GOLFWORKS TOTAL SHOP SET-UP KIT
56999
ONLY $
Universal Vise
Universal Vise Jaw Set
1" x 30" Belt Sander
Linen Ferrule Belt
6" Chop Saw
Swingweight Scale
Swingweighting Kit
48" Club Length Ruler
Gripping Station
Double Sided Grip Tape
Grip Build Up Tape
Grip Solvent
Utility Knife with
Hook Blades
Grip Installer
Tape Stripper
High Strength Epoxy 8 oz.
Epoxy Cleaning Kim Wipes
Black Ferrule Kit
Ferrule Installer
Ferrule Turning Arm
Heat Gun
SAVE OVER
$240!
$99.99
$59.99
$149.99
$69.99
$3.99
$39.99
$89.99
$29.99
$10.99
$109.99
$5.79
$3.49
$5.99
GWUK
$4.99
BBGIT
$9.99
GW1101
$14.99
EPX4
$7.99
GW0015
$2.99
GW2001
$39.99
GW1003
$6.99
EFTA
$19.99
EHGK
$24.99
TOTAL
$813.08
Savings $243.09
Kit Price: GW1206 $569.99
NOTICE: CANNOT BE
SHIPPED BY AIR.
GOLFWORKS ASSEMBLY KIT
NOTICE: CANNOT BE
SHIPPED BY AIR.
9999
ONLY $
Swingweight Scale
Shaft/Tube Cutter
Rubber Shaft Clamp
Wood Ferrules
Iron Ferrules
Ferrule Installer
Sand Paper
Grit Edge Graphite
Shaft Blade
Tour Set Shafting Epoxy
Epoxy Cleaning
Kim Wipes
4 Gram Tip Weights (iron)
2 Gram Tip Weights (iron)
2 Gram Tip Weights (wd)
2 Gram Tip Weights (grph)
Grip Solvent
Grip Installer
Kit Price:
122
UCMV
UCMVJWS
MA2007
IVS3C
PF30B
CSM6
NESC
GW2005
RUL48
GGS
DFTG218
BU2
SOMQT
VSWC
RUL48
STC
RSC
60PW
60PI
GW1003
HSO
GREB
TSPE
$49.99
$10.99
$9.99
$1.99
$2.49
$2.49
$6.99
$1.00
$4.99
$9.99
GW0015
$2.99
LPIGI4
$3.49
LPGI2
$3.99
LPW2
$3.99
LPG2
$3.99
DFTG218
$5.79
SOMQT
$5.99
BBGIT
$9.99
TOTAL
$141.13
Savings $41.14
GW1204 $99.99
12/23/08
10:12 AM
Page 123
KITS – TOOLS
GOLFWORKS RESHAFTING KIT
42599
ONLY $
Universal Vise
Universal Vise Jaw Set
1" x 30" Belt Sander
Linen Ferrule Belt
6" Chop Saw
Micro Shaft Prepping Belt
18 Volt Cordless Drill
Wood - Wire Hosel
Cleaning Brush
Iron - Wire Hosel
Cleaning Brush
Blue Away
Safety Glasses
Leather Gloves
High Strength Epoxy 8 oz.
Epoxy Cleaning Kim Wipes
Black Ferrule Kit
Ferrule Installer
Ferrule Turning Arm
Heat Gun
UCMV
UCMVJWS
MA2007
IVS3C
PF30B
CSM6
M130B
GW0046
RUL48
$99.99
$59.99
$149.99
$69.99
$3.99
$39.99
$3.49
$39.99
$10.99
GW1060 W
$4.99
GW1060 I
$4.99
BLAW
$9.99
FEG
$4.99
LGLO
$12.99
EPX4
$7.99
GW0015
$2.99
GW2001
$39.99
GW1003
$6.99
EFTA
$19.99
EHGK
$24.99
TOTAL
$619.30
Savings $193.31
Kit Price: GW1205 $425.99
SAVE OVER
$190!
NOTICE: CANNOT BE
SHIPPED BY AIR.
CUT-OFF SAW/BELT
SANDER PACKAGE
NOTE: ADDITIONAL
SHIPPING CHARGES
REQUIRED DUE TO
WEIGHT.
A great and affordable kit to tackle the toughest jobs in clubmaking,
golf shaft prepping and cutting. The GolfWorks 1" x 30" belt sander
can be used to prep graphite and steel shafts as well as finish ferrules
(see page 109 for ferrule finishing supplies) and The GolfWorks 6"
Chop Saw makes the tedious and time consuming task of cutting
steel and graphite shafts a breeze.
8999 SAVE $1999!
BSCOM $
123
12/23/08
10:13 AM
Page 124
TOOLS – KITS
Universal Grip Gauge
Utility Knife with
Hook Blades
Grip Installer
Tape Stripper
Grip Solvent 16 oz.
Rubber Shaft Clamp
GRIP ESSENTIALS KIT
29
ONLY $
99
DFTG218
MAGG
$5.79
$12.99
GWUK
BBGIT
GW1101
GW0037
RSC
TOTAL
$4.99
$9.99
$14.99
$3.99
$1.99
$54.73
NOTICE: CANNOT BE
SHIPPED BY AIR.
2999
SAVE OVER $24!
GW1212 $
GOLFWORKS
GRIPPING KIT
All you need to perform quick and professional gripping.
The GolfWorks gripping kit includes the GolfWorks gripping
station, tape (double coated and build up), a gallon of solvent
and the GolfWorks Universal Grip Gauge. Save over $24 when
purchased as a kit.
GolfWorks Gripping Station
2" Double Sided Grip Tape
2" Build Up Tape
GolfWorks Universal Grip Gauge
1 Gallon Gripping Solvent
GGS
DFTG2
BU2
MAGG
SOMGL
TOTAL
$109.99
$9.79
$3.49
$12.99
$18.99
$155.25
129
SAVE OVER $25!
GGSK $
QUICK GRIP KIT
The Maltby Design Quick Grip Kit is the safest and easiest way to
install rubber grips. Eliminates any chance of damaging a graphite
shaft from over tightening in a shaft clamp and is extremely simple to
use. The Quick Grip Kit includes the new Maltby Design Quick Grip,
vise mount attachment, a roll of double coated Pip Strips and a can of
GolfWorks Aerosol Grip Solvent. Priced separately they total over
$69.00! DVD instructions included.
Instructional Gripping DVD
Quick Grip
2" Double Sided Grip Tape
Vise Mount Adaptor for Quick Grip
GolfWorks Aerosol Solvent
–
GW1030
DFTG2
GW1037
NFGA
TOTAL
NOTICE: CANNOT
BE SHIPPED
BY AIR.
99
SUPER FAST &
EASY TO USE!
FREE
$39.99
$9.79
$12.99
$4.99
$67.76
5499
SAVE OVER $12!
GW1202 $
124
NOTICE: CANNOT BE
SHIPPED BY AIR.
12/23/08
10:14 AM
Page 125
SHOP SUPPLIES – TOOLS
BENCH &
FLOOR
COVERING
We found a great material to cover work bench and
shop floors that is reasonably priced, and helps prevent “shop wear”. This polyvinyl coined material
provides better cushioning against scratches and
dents to wood and iron heads than a table top. And,
it gives your shop a very professional, clean look.
The dark green color makes it easy to spot small
parts like ferrules and weights. Available in 24" x
96" roll or in custom sizes.
NOTE: ADDITIONAL
GW1008 $44.99
SHIPPING CHARGES
MAY BE REQUIRED DUE GW1000F$3.99
TO WEIGHT.
Standard 2' x 8' size
Per Square Foot for Custom Sizes
BENCH MOUNT
SHAFT
HOLDER
Keep clubs and shafts securely standing against your workbench, ready for the
next step in the assembly/repair process. Easily attaches to the front, top or
side of your workbench with two screws. 12 notches allow you to lean up to a
dozen clubs or shafts in place. Rubber coating protects finish on steel and
graphite shafts.
BMSH
GOLF CLUB
CURING/
DISPLAY RACK
A great addition to any shop (or den)! The Golf
Club Curing rack safely holds your clubs while
epoxy cures, ensuring that the bond is strong and
alignment is not compromised. It is also a great
rack for displaying clubs in a shop or home.
$19.99
SHARPIE® MINI
MARKER
4-PACK
The best-known name in permanent markers. 4
pack includes: Black, Blue, Green and
Red markers.
SP001
$5.99 4-Pack
GW1114 $59.99
SHOP
APRON
Protect your clothes with
this attractive, durable shop
apron. Rayon/cotton blend
for durability. Two large
pockets. One size fits all.
APRON
$ 9.99
125
1/5/09
3:17 PM
Page 126
TOOLS – FITTING
™
PURELAUNCH
EASY TO USE! SETS UP IN SECONDS!
The Zelocity Purelaunch™ launch monitor uses two integrated Dopplar Radar transceivers
instead of photography for more precise club head and ball data recordings. The Dopplar
Radar follows the path of the club head and ball to record club head speed, launch angle, ball
speed, backspin, side spin, face angle, distance and PTR (power transfer ratio). Lightweight
and portable, the PureLaunch™ launch monitor sets up in seconds and is powered by a
rechargeable battery or AC power. The PureLaunch™ can be used inside or outside without any
special lighting requirements.
Included Launch Data Software clearly displays shot information instantly on screen:
FEATURES:
• Instantly, accurately displays & records
critical information for every shot
• Builds history for analysis and
improvement
• Lightweight & completely portable for
use indoors or outdoors
• Accommodates both left and
right handed swings
• Patented radar technology
• Compatible with WinXP Home,
WinXP Professional, Vista and
Win2000 operating systems
• Tubular steel frame with rugged ABS/PC
plastic radomes and processor cover
• Power switch, USB connector,
AC power connector
• External LED indicators for Power
ON/OFF and Radar ARMED/NOT ARMED
• 10 ft. USB cable provided for
communication from computer to
PureLaunch™
• No maintenance required; One (1) year
factory warranty; Repaired at factory
• Operates using Battery or AC power
outlet; Recharge ~ 10 hrs;
Avg. Life ~ 6 hrs
• One (1) year customer service and
software upgrades included
ZG0001
$3,995.00
GOLFWORKS
BALL FITTING
SOFTWARE
Fit The Right Ball To Any
Player's Game!
The GolfWorks has teamed with Advanced Golf SolutionsTM to
help develop an incredible fitting tool. Thousands of hours of
actual ballistic golf ball testing of the top brands of golf balls
provided the data for this easy to use ball fitting software. The
software uses the data from the selected ball as a base to compare to all brands. Insert the golfers current brand of golf ball
and personal launch monitor data (ball speed, launch angle,
average offline ball direction) and the software will provide
the optimal golf ball brand based on the players request for
distance or control.
Professional Ball Fitting Software:
• A must have tool to complete any launch monitor fitting.
• Requires only one brand of ball during monitor fittings.
• Provides the optimal ball based on the players
requirements for distance, spin and accuracy.
• Driver, fairway wood and putter analysis included.
• Golf ball data recorded from actual ballistic testing.
• No set-up required.
• Updates of new golf balls will be offered every year.
• List all golf balls based on distance, spin and accuracy.
• Prints comparison data in easy to read forms.
AGS003 Professional Ball Fitting Software $425.99
AGS005 2009 Golf Ball Fitting Software Update $49.99*
ZELOCITY
RADAR
The RADAR™ Golf
Ball Flight Monitor,
endorsed by Vijay
Singh uses patented
Doppler-radar technology to measure ball
velocity and precisely
calculate shot distance.
Extremely accurate and
able to measure distances from 15 to 420
yards, this unit is ideal
for golfers looking to
improve their distance
control for all clubs in
the bag. Portable and lightweight, The RADAR™
fits easily in your golf bag and can be used indoors,
outdoors and on the course.
• Indoor – outdoor use
• Onboard display to
show shot data
• Displays distance in
yards or meters
• Measures ball velocity
and calculates distance
• Operates on one 9
volt battery (not included)
• No setup required
• Made in the USA
ZG0005 $229.99
*Available March 2009
126
12/30/08
2:11 PM
Page 127
FITTING – TOOLS
TOUR LOCK PRO
Tour Lock Pro is a revolutionary weighting technology that allows every golfer to fine tune, personalize and enhance the performance of any golf club.
Testing shows that optimizing the weight of a club produces a more consistent, tighter ball contact
dispersion with the clubface, raising the “power transfer ratio” resulting in greater distance,
improved accuracy and better club head feel.
Now it is easy and affordable to fine tune every golf club in your bag. There are 9 TLP weights to
choose from; 8 gm, 12 gm, 20 gm, 30 gm, 40 gm, 50 gm, 60 gm, 80 gm and 100 gm. Each weight
is interchangeable and simple to install, which makes it easy to find the optimal weight for every
club in the bag; from putter to driver.
Tour Lock Pro’s Patent Pending Innercore Clamping and End Cap Technology securely holds Tour
Lock Pro weights in place with no chance of loosening or rattling.
The weight raises the balance point of the club increasing overall feel, while at the same time,
dampening unwanted vibration, producing a better feel and a solid, sturdier club.
Tour Lock Pro conforms to U.S.G.A. and R & A Rules of Golf.
TL0001
TL0002
TL0003
TL0011
TL0004
TL0012
TL0005
TL0006
TL0007
TL0009
TL0010
Tour Lock Pro Weight
8 Grams
12 Grams
20 Grams
30 Grams
40 Grams
50 Grams
60 Grams
80 Grams
Tour Lock Pro Weight 100 Grams
Grip Modifier
TLP 3/16" Wrench
$6.50
$6.50
$7.99
$8.49
$8.99
$9.99
$12.99
$14.50
$14.99
$19.99
$1.00
AWARD WINNING
DANCIN’ DOGG
SIMULATOR
Combines a full simulator
and swing analysis designed
specifically for home use!
V1 GOLF
Swing Analysis
Software
V1 Golf brings powerful swing analysis
software to your computer — the same
technology utilized by top Tour players!
With V1 Golf, analyze and diagnose
faults simply and concisely.
• Store/retrieve your digitally recorded
golf swing.
• Compare your swing to a
professional, or a previously
recorded swing.
• Use on-screen tools to analyze
your swing.
• Easily monitor adjustments and
improvements.
V1GS
$89.99
Operating System: Microsoft Windows
ME, Windows 2000 Professional, Windows
XP Home, Windows XP Professional or
Windows Vista. Please call for additional
technical specifications.
Hop on the simulator with your friends and family to play whole
rounds together at Pebble Beach, St. Andrews, or one of the
other world's best courses on the included EA Sports™ Tiger
Woods PGA Tour© game.
Can't spend enough time at the range? With Dancin'
Dogg you can practice at home any time of the day
or night.
Sixteen advanced optical sensors accurately measure
your club through impact, providing feedback on your
swing path, face angle and club head speed, distance
carried, flight path and more.
See yourself improve and
DD0001
your ball arch closer and
$399.99
closer to your target with
each and every shot.
Hit real balls or foam balls, or just practice your swing using no balls at all. With the
Dancin' Dogg Golf Simulator, you don't have to deal with ball tethers or iron modifications. Balls can be struck directly off the turf or off the tees.
Precise path of the shot
Don't spend thousands when Dancin' Dogg gives you so much more for so much
and detailed Swing
less. Don't be fooled by toys with tethers that are not accurate.
Analysis with the dashboard.
THIS INCLUDES EVERYTHING YOU NEED TO ENJOY THE FULL VALUE OF THE PROGRAM.
• Ultra Durable Swing Pad with dead on accurate sensors
• Dancin' Dogg Program Software
• EA Sports™ Tiger Woods PGA Tour© Game
• USB Cable
• Set of indoor safe balls
• Variety length of tees
SYSTEM REQUIREMENTS
• Personal Computer with USB 2.0
• Windows XP (32 bit) or Windows Vista (32 bit) operating system
• PC with 800 MHZ or higher processor clock speed recommended (single or dual processor system)
• 256 megabytes (MB) of RAM or higher recommended
• 2.3 gigabytes (GB) of available hard disk space
• CD/DVD-Rom Speed: 8x
• Keyboard and Microsoft Mouse or compatible pointing device
• EA Sports Tiger Woods PGA Tour 07 requires a video card with at least 64 MB of video RAM with DirectX
9.0c compatible driver with one of ATI Radeon 8500, NVIDEA GeoForce 3, GeoForce 4, Ti or greater
chipsets, and a DirectX 9.0c compatible sound card
127
1/5/09
12:07 PM
Page 128
TOOLS – FITTING
IMPACT MARKING DECALS
GW1041
Knowing exactly where the ball contacts the face of the club during impact can eliminate many
unknowns in dynamic fitting. The GolfWorks impact marking decals are now offered in oversized
iron and wood sizes as well as in rolls for high volume shops.
GW1041P
12 pack - Oversized Iron Decals
$3.99
GW1041
Roll of 200 Oversized Iron Decals
$39.99
GW1042P
12 pack – Oversized Driver Decals
$3.99
GW1042
Roll of 200 – Oversized Driver Decals
$39.99
IMDW
15 pack – Wood Decals
$3.99
IMDI
15 pack – Iron Decals
$3.99
IMDP
21 pack – Putter Decals
$4.99
IMDW
IMDP
IMDI
MALTBY
LIE ANGLE BOARD
The Maltby Professional Lie Fitting Board is constructed of heavy duty, clear Lexan for
strength and durability. The Maltby graphics are brilliantly displayed underneath the board
and protected by polycarbonate lamination to ensure the logo and helpful alignment lines will
last forever. The oversized dimensions of 14"
wide by 233/4" in length
make this the most
durable and reliable lie
fitting board available.
All edges have been
machined for safety and
the ball position is
located at the center of
the oversized board to
eliminate any chance of
an avid golfer striking
the edge of the board.
MA3011 $44.99
LIE ANGLE
IMPACT
DECALS
The GolfWorks Lie Angle Impact
Decals pre set lines makes identifying and
measuring the soles impact location from a lie
angle board a breeze. A nice professional touch to any iron fitting. Rolls of 600 offered for high volume fitting centers. For irons only.
GW1043P Lie Angle Decals - 21pk
$1.99
GW1043 Lie Angle Decals - Roll of 600 $29.99
MAGNETIC LIE
ANGLE TOOL
With this fitting tool, the flight path of the ball
as it leaves the clubface can be effectively
demonstrated. The magnetic base snaps onto the
iron face. The club lie is correct when the alignment of the tool is directly toward the target.
MLAT
$12.99
GOLFWORKS LIE
FITTING BOARD
Now you can check the angle of the clubhead at impact. This special hard plastic
surface makes a temporary mark on the
sole to show if your club is too upright or
flat. Measures 8" x 19", 3/16" thick.
S1632
128
GW1042
MALTBY
TRIANGLE
GAUGE
Selecting the proper
wedge for a particular type of player by the
measured bounce angle
simply does not work. The
bounce angles listed on a wedge do
not account for
sole width, sole
radius, leading
edge height or
leading edge grind.
All of these
design characteristics
influence the effective bounce of a
wedge. The Maltby
Triangle Gauges now
offer the club fitter a
definitive way to
measure and compare the “effective”
bounce of most
wedges.
With this knowledge, the
club fitter can easily
select a wedge to perfectly fit the characteristics of
any golfer. Manufactured
from durable .030" White
Syrene. Also available, a
1 hour information
packed DVD; Learn All
About Wedges.
Gauge Set Only
MA3012 $9.99
SET INCLUDES:
54°, 55°, 56°, 57°, 58°
and 60° Triangle Gauges.
Gauge Set + DVD
MA31012E $14.99
$12.99
12/23/08
10:18 AM
Page 129
BOOKS & VIDEOS – TOOLS
HOW GOLF CLUBS
WORK . . .
By Ralph Maltby
This book may be small, but it's packed with information on how to get more out of your golf clubs.
Completely re-written for 2008, this “Little Black
Book” is packed with valuable golfer tips and
interesting information. 122 pages, soft cover.
HGCW $9.99
THE MALTBY
PLAYABILITY
FACTOR
Understanding Golf Club Dynamics by Ralph Maltby
Ralph Maltby’s latest book is the product of over a decade
in research and a lifetime of experience with golf club
design. Having designed and analyzed irons for major manufacturers and his own company, and having fit golfers of
every playing ability including many touring professionals,
Ralph has developed an analytical system to understand
how iron club designs play — The Maltby Playability
Factor. In this book, he explains how several mass and
dimensional properties of an iron head determine how the
clubhead behaves when striking the ball, thus determing a
clubheads playability.
*FREE updates available at: ralphmaltby.com!
1st Edition
2005
RM9001
$19.99
GOLF CLUB DESIGN,
FITTING, ALTERATION &
REPAIR
By Ralph Maltby
THE COMPLETE
GOLF CLUB
FITTING PLAN
Used By Clubmakers and OEM
Designers World Wide. The most
complete study of golf equipment available.
STEP-BY STEP
MANUAL
By Ralph Maltby
The most comprehensive program manual
ever written on the subject of golf clubfitting. This manual leads you step by step
so you can properly fit equipment to any
golfer. Easy-to-use spiral bound format.
Includes Fitting Worksheets and
Scorecards.
INCLUDES:
• Club repairs and alterations
guide
• How to get started in repair and
clubmaking
• Club balancing, swingweight
and frequency
2nd Edition GLF2 $24.99
4th Edition 1995
GCD4 $59.99
LEARN ALL ABOUT
DVD Series By Ralph Maltby
THE GOLF CLUB
IDENTIFICATION
& PRICE
GUIDE IV
Want to know historical and price
information on just about every golf
club produced from 1950-1998?
The Golf Club Identification & Price
Guide IV has it! You just might have
a hidden gem sitting in your garage!
4th Edition 1999
GCID4 $24.99
LEARN ALL ABOUT WEDGES
RMLAWDVD
60 minute DVD
$9.99
LEARN ALL ABOUT GRIPS
RMLAGVD
40 minute DVD
$9.99
Is It Me Or My Equipment?
RMEQPDVD
90 minute DVD
$9.99
GOLF TECHNICAL INFORMATION VIDEO
Tips, Tricks & Techniques
BK9001 55 minute video $9.99
BK9002 55 minute DVD
$9.99
129
12/23/08
10:19 AM
Page 130
TOOLS – SWINGWEIGHTING
“Measures
Total Weight”
MALTBY GOLF CLUB SCALE
Measure Swingweight, Club Weight,
Or Component Weight
The “world standard” golf club scale designed by Ralph Maltby, measures swingweights using the industry standard 14"
fulcrum principle, which provides direct swingweight readings (C8, D2, etc.). Scale markings are large, easy to read,
and are printed on both sides of the Scale, so readings can be taken from either side. By placing any club in the resting
cradle, this Scale also measures total club weight. Permanently mounted parts tray measures the weight of individual
components. Weights can be read in grams and ounces. The scale has a bubble-level indicator and adjustable feet to
ensure accurate readings no matter what surface it's on. Each scale is precision machined, assembled by hand, calibrated
in our factory, and includes a plate that certifies the accuracy of each scale. When you purchase the Maltby Design Golf
Club Scale, you are buying a precision instrument that will reward you with a lifetime of use.
FEATURES:
• 14" fulcrum scale
• Hand calibrated and registered
• Quick reference guide on scale
SWRM Golf Club Scale
$199.99
• Weigh clubs or components in grams or ounces
• Leveling legs with bubble indicator
• Made in America
SWRMGT Grip Tray (optional)
$14.99
NESC
Value Line Golf Club Scale $89.99
ECONOMY
SWINGWEIGHT SCALE
Measures swingweight quickly and accurately. Scale rests on workbench
and balances on its curved surface. Sliding weight indicates measurement.
Easy to use and stow away when you are done! A great choice for low to
medium volume work.
VSWC Economy Swingweight Scale $49.99
SWINGWEIGHT
KIT
– 169 PCS
1 DOZEN EACH:
• 2, 4, 6, 8, 10 gm. Wood Tip Weights
• 2, 4, 6, 8, 10 gm. Iron Tip Weights
• 2, 3, 4, 5 gm. Graphite Shaft Tip Weights
• Shaft Butt Weight Ports
• 1 lb. Lead Powder
GW2005 $34.99
130
The optional grip tray (SWRMGT)
lets you accurately measure the
swingweight of an ungripped
club using an actual grip.
These are the same tip weights used by major
manufacturers. Simply slide into position in the
shaft tip, verify final swingweight and epoxy the
shaft into position. Reusable.
VALUE LINE
GOLF CLUB SCALE
An economical swingweight scale that gives industry standard readings.
Large and easy-to-read scale for swingweight and total club weight measurements. Cradle allows quick weighing of total weight in both grams
and ounces.
MEASURES: • Total weight • Swingweight at 14" fulcrum point
“Measures Component Weight”
BRASS PLUGS
Code
SITW2
SITW4
SITW6
SITW8
SITW10
SWTW2
SWTW4
SWTW6
SWTW8
SWTW10
GTW2
GTW4
Description
.370" Steel Iron Tip Weight (2g)
.335" Steel Wood Tip Weight (2g)
Graphite Tip Weight (2g)
Graphite Tip Weight (4g)
Price Doz.
$4.99
$4.99
$5.15
$5.20
$5.25
$4.99
$4.99
$5.15
$5.20
$5.25
$5.49
$5.49
Code
LPW
LPW
LPW
LPW
LPW
LPIGI
LPIGI
LPIGI
LPIGI
LPIGI
LPG
LPG
LPG
LPG
Lead Plug Wates are epoxied into the shaft tip
before assembly. Fit a maximum .285" inside diameter for wood shafts, .312" diameter for iron shafts.
Also available for graphite iron and wood shafts
with a maximum .148" inside diameter.
Description
Price Doz
2 gm. Wood for Steel Shafts
$3.49
$3.49
$3.49
$3.99
$3.99
2 gm. Iron for Steel Shafts
$3.49
$3.49
$3.49
$3.99
$3.99
2 gm. Woods/Irons for Graphite Shafts
$3.99
$3.99
$3.99
$3.99
LEAD PLUG WATES
12/23/08
10:20 AM
Page 131
SWINGWEIGHTING – TOOLS
LEAD FOIL
HIGH DENSITY
TAPE
LEAD
FOIL TAPE
Use as temporary weight on the back of
Ideal for fitting. It is adhesive backed and can be
both wood and iron clubs to achieve correct total weight and swingweight.
applied quickly and easily or left on permanently.
Heavier than standard lead tape.
LT100
LT36
HDLT 1/2" x 75"
/2" x 100"
/2" x 36 Yds
1
1
$6.99
$34.99
TUNGSTEN
POWDER
Tungsten powder permits the addition
of extra weight in less space at the
clubhead end for more efficient swingweight increases.
Especially useful with new
ultralight
graphites.
Weighs 1.5
times as much
as lead powder.
.5-lb. container.
TP
$19.99
This handy little tool allows you
to remove a rattle in a shaft or
place lead and a cork down the
shaft of a club without damaging
the grip.
GRIP SAVER
SAVER
$12.99
The GolfWorks Head Tac is
now available in a syringe for
easy insertion into metal wood
hosel bores or a pre-drilled
hole into the metal wood shell.
Head Tac instantly stops those
annoying rattles in metal
woods and can be used to
safely add weight to metal
woods.
GW0035
$8.99
The GolfWorks Professional Scale measures
grams up to 2500 grams in 0.5 gram increments. Extremely accurate to 1/5000 of a gram
the Professional Scale also measures in pounds
(lb) and ounces (oz). Has a pieces mode for
counting small parts in the included Parts Bowl.
Protective metal tray
covers the scale
and also has a
flip down lid
to prevent
damage
when not in
use. Uses 3
AA batteries
(included)
and has an
DC adaptor
port (Adaptor
not included).
Automatically
shuts off after
non use to save
batteries.
Includes a 4.6"
diameter brushed
metal tray for
measuring golf
club components.
$6.99
POWDERED
LEAD
Many clubmakers and manufacturers use lead powder to add weight
down the shaft to increase swingweight. Useful when ultralight
weight shafts are used. Can be used
in conjunction with the shaft butt
weight ports (BWP) for counterbalancing steel shafted woods, irons
and putters and can be used for
weighting older wood wood heads
under the
soleplate. 1 lb. container.
LP
GW1018 $44.99
Professional Scale
$7.99
A. 441/2" RAM
ROD
A
5/32" diameter rod fits down a
graphite shaft. Perfect for
packing lead down a shaft or
removing a stubborn head. Fits
through a grip vent hole to
tighten or remove loose tip
weights. High-strength steel
with a wooden handle.
RR
$14.99
For Graphite Shafts!
B. HEAVY
DUTY 421/2"
RAM ROD
1
HEAD TAC
SYRINGE
PROFESSIONAL
SCALE
SHAFT BUTT
WEIGHT PORTS
A great tool for counterbalancing steel shafted
woods, irons and putters. The durable plastic
weight port fits into the butt end of a steel shaft
and is secured via grip installation. 12 per
package. Can be sanded to fit graphite shafts.
B
BWP
/4" rod is ideal for driving off
stubborn ironheads, applying
heat inside a shaft tip to loosen
woodheads, or tightening loose
tip weights. Cold rolled steel
with a vinyl handle.
RR7
$14.99
C. 48"
HEATING
ROD
3/16" rod is ideal for driving off
stubborn ironheads, applying
heat inside a shaft tip to loosen
woodheads, or tightening loose
tip weights. High-strength
steel with wooden handle.
HRD48 $6.99
$14.99
SWINGWEIGHT
CORKS
C
A must-have
when adding
lead ot tungsten
powder down a
steel shaft to
increase swingweight. Apply a
small film of
epoxy to the
cork and force
down the shaft
with a ram rod to secure powdered weight.
CI 25 pk. Irons $1.99
CO 25 pk. Woods $1.99
131
12/23/08
10:21 AM
Page 132
TOOLS – MEASURING
MALTBY CLUBLENGTH RULER
The Maltby Design Ruler is the most accurate club length ruler ever
made, specifically designed for the club maker that demands perfection. A
lie angle reference gauge is attached to the soling plate to ensure that any
club will be measured in its correct lie angle position. The ruler platform
is set high above the ground to allow modern large headed putters to be
correctly measured for finished length. The ruler base has been designed
to measure putters up to 531/2" in length for those difficult to measure
“long” and “belly” putters. The most innovative feature of the Maltby
Design Ruler is the spring loaded drop down rearward section of the ruler.
Gripped golf clubs can be accurately measured regardless of the shape or
size of the grip. This is especially important with assembled putters. A
second rule has also been added to the back of the ruler for measuring tip
trim amounts from raw shafts.
• Accurately measures the lengths of assembled woods, irons,
wedges and putters with grips regardless of the grip size or shape.
• Attached lie angle gauge allows lie angles to be set and or
checked during measuring for added accuracy.
• Double bend putters can be correctly measured along the shaft axis.
• Heavy duty construction to withstand the demands of high volume repair shops.
• Shaft cradle securely holds raw shafts when measuring tip trim amounts.
• Easily measures long putters up to 531/2" in length.
MA1000
Measuring Irons
Maltby Clublength Ruler
Spring loaded drop- down for measuring
assembled clubs
$159.99
Measuring Woods
Measuring Putters
Clearly marked
in inches and
millimeters
MALTBY BENCH RULER
The Maltby Bench Ruler is a quick and accurate tool to measure club lengths on
irons, woods and wedges. The soling plate can be adjusted to match the lie angle of the
golf club being measured to insure proper length measurements. Shaft alignment pins
at the base of the ruler align the shaft to aid in accurately setting the club at its correct
playing position. The Maltby Bench Ruler is lightweight and easily mounts to any
work bench.
• Accurately measures the lengths of assembled woods, irons and wedges.
• Attached lie angle guide allows lie angles to be set for accurate length measurements.
• Lightweight construction easily mounts to work bench.
• Shaft alignment pins align shaft for accurate lie angle settings.
• Measures clubs up to 47" in length.
• Measures both right-hand and left-hand clubs.
MA2010 Bench Ruler $119.99
132
Lie Angle Gauge
12/23/08
10:22 AM
Page 133
MEASURING – TOOLS
THE GOLFWORKS
48" ALUMINUM RULER
Simply put, every shop needs one of our 48" rulers. It not only measures shaft length, it tells you how to do the job!
This heavy duty aluminum ruler has instructions printed on the surface, including
• Instructions for correctly measuring shafts
• Made of 1/8" thick by 2" wide aluminum.
RUL48
$10.99
EXACT
MEASURE TOOL
Designed for custom clubmakers, use this tool to obtain consistently accurate
measurements for tip and length trimming. Measures up to 48" in 1/4" increments. Designed to be used flat on a workbench to reduce awkwardness and
increase accuracy. Panel flips up to align with clubhead sole so accurate finished
length is measured.
TMR
$44.99
PUTTER MEASURING
RULER
Measures the actual putter playing length on most any assembled putter.
Bottom cut-out accommodates most models. Optional stand allows you to
lean the putter against the ruler while you measure it. Can be used right or
left handed. 381/2" long.
EMPR Putter Ruler
EMPRS Optional Stand
$14.99
$29.99
Our unique, cut-out design makes
measuring assembled clubs easy!
SELF-STICK
RULER
Adhesive backed 48" ruler sticks to a workbench for handy shaft and
club length measurement.
SSTR
$6.99
6"
SCALE
Handy, pocket-sized scale for quick and easy measurements of a variety of club specifications.
GR
$1.99
48" BENCH
MOUNT
RULER
Ideal for measuring/marking shafts for trimming,
the Bench Mount Ruler mounts to the side of your
workbench. The L-shaped piece attaches to the
workbench, leaving the bright yellow color with
bold black marking on a ledge to rest the shaft on.
Always "right there" on your workbench, so it
is handy.
BMR
$14.99
133
12/23/08
10:22 AM
Page 134
TOOLS – MEASURING
MALTBY LASER
FREQUENCY MACHINE
The Maltby Design Laser Frequency Machine is a valuable tool for clubmakers to consistently measure shaft frequency of both assembled clubs and raw shafts. Other frequency
machines measure reflected light which often results in missed or inconsistent frequency
readings. By using a laser as the primary light source, measurements are not affected by
ambient or reflected light, shaft color or shaft material. New features for 2008 include:
1) A much improved clutch clamping system that will clamp both gripped golf clubs and raw
shafts without changing clamps. 2) A heavy duty base to better protect the
electronic components of the analyzer and to eliminate the need for raiser
blocks when using on a workbench and 3) Heavy duty laser assembly with a
dial locking mechanism to insure the laser lights stay permanently aligned. The
LCD screen displays CPMs (cycles per minute) in both 3 and 5 digits for those
clubmakers looking for unmatched precision readings. Complete instructions
included. Operates on 110 VAC.
FEATURES:
• Measures assembled clubs or raw shafts from the butt end or tip end.
• Laser CPM counter measures in 3 digit and 5 digit readings.
• Laser posts adjust to ensure beam and shaft align properly during oscillation.
• Average button to determine the average for multiple tests of a shaft.
• Speed locking clamp guarantees consistent pressure on all shafts for accurate readings from one shaft to the next.
• Easy to read LCD display.
• 5" clamp will hold raw and gripped shafts.
• Can be used to do Zone Frequency testing of raw shafts.
• ASTM standard 205 tip weight included for measuring raw shafts.
MA2014
$399.99
Laser Frequency Machine
GLFMC
$5.99
Pad of Frequency Charts
MALTBY GOLF SHAFT DEFLECTION BOARD
of different shafts can be compared to establish where flex is concentratShaft manufacturers employ various methods of measuring shaft flex, and
ed: at the tip, in the middle, or toward the butt end. Not recommended for
some shaft models vary in flex considerably from shaft to shaft. The Golf
shafts 75 grams and under.
Shaft Deflection Board gives the serious clubfitter a tool to compare a
shaft’s exact flexibility to industry standards or to other shafts. By
The high quality Golf Shaft Deflection Board is made from oak plywood
mounting the shaft on the board and installing the 7 lb. weight on the tip,
and steel. Weighing only 20 lbs., it can be securely attached to a wall
the flex can be read from the color coded line where the tip is positioned.
with the included toggle bolts. Instructions for use are included.
Color coding identifies X, S, R, A and L flexes. In addition, the curvature
FEATURES:
• Engineered to be the best on the market
• Eliminates guesswork
• Use for raw shafts as well as finished clubs
• Looks great on the shop wall!
GSDB
$179.99
134
12/23/08
10:23 AM
Page 135
MEASURING – TOOLS
MALTBY PRECISION
MILLED GOLF CLUB
MACHINE
The Ideal Tool To Measure Iron Heads For
Maltby Playability Factor!
Optional swivel base
attaches easily to
gauge
This is the finest gauge we offer! Similar to the Ralph Maltby Golf Club Gauge, but
heavy-duty. Features a thumb knob on the adjustable lie angle arm. The soft, nonmarring aluminum clamping area for the shaft (or hosel centerline finder – HCLL
below) is large. The heavy base and upright arm are precision milled and the
shaft-clamping fixture is made from a soft, non-marring aluminum. All
measuring lines are machined into the unit.
MEASURES:
• Iron, putter and wood loft and lie angles, face progression and hosel offset
• Wood face angle (open or closed)
• Iron bounce and sole angle
• All length, height and width measurements of any head
• All RH and LH clubs
This is a precision measuring instrument that is very easy to operate
and as accurate as any you will find. The optional swivel base provides even more versatility in
obtaining precise measurements from any club. A Loft Measuring Protractor is included with each unit.
LOLI2 Golf Club Gauge $699.99
SLLB Swivel Base (optional) $74.99
NOTE: ADDITIONAL SHIPPING CHARGES MAY APPLY DUE TO WEIGHT.
MALTBY GOLF
CLUB GAUGE
Measures Five Different Specifications
The Maltby Design Golf Club Gauge precisely measures lofts, lies,
face progression and offsets of any wood, bounce, head length,
height and width dimensions, iron or putter as well as wood-head
face angles. The base and upright arm are precision milled and the
shaft-clamping fixture is made out of soft non-marring aluminum.
All measuring lines are engraved into the unit.
Includes a 6" scale and a golf club protractor.
GW1040 $349.99
VALUE LINE
GOLF CLUB GAUGE
An economical alternative to the more expensive gauges, the Value
Line Golf Club Gauge, accurately measures all important wood, iron
and putter specifications. Comes completely assembled and
includes a machinists’ 6" scale, a golf club protractor, hex
key wrenches and a complete instruction booklet.
Measures right- and left- handed club heads
FEATURES:
• Iron, putter and wood loft and lie angles,
face progression and hosel offset
• Wood face angle (open or closed)
• Iron bounce and sole angle
• All length, height and width
measurements of any head
HGCG
$149.99
SLLB
$74.99 Optional
Swivel Base
A must-have too to accurately measure offset face progression,
and hosel centerline-to-face centerline dimensions, all important
measurements in determining Playability. All modern tip sizes
included. Work in all the Golf Club Gauges we sell! Includes a
convenient stand with sizes labeled.
HCLL
$59.99
HOSEL CENTERLINE FINDERS
Digital Calipers with large
LED display makes
measuring bore depths,
face heights, quick and easy.
GDC
$34.99
GOLF CLUB
PROTRACTOR
Our Golf Club Protractor is perfect for reading
loft and lie measurements for woods, irons and
putters. The bottom of the gauge rests on a flat
surface while the other side is pressed against the
club face (for loft). Stainless Steel.
GWPRO $19.99
DIGITAL CALIPER
The Magnetic Protractor easily measures loft and lie of clubs
in the playing position. Works with any measuring machine.
Accurate to half a degree with a large 4" dial for easy reading.
Loft and lies specifications printed on the back.
MAGNETIC PROTRACTOR
PRO
DOUBLE BEND
ASSEMBLY JIG
The perfect tool for correctly positioning a double
bend putter shaft into a putter head during assembly
to ensure proper loft and lie angle measurements. The GolfWorks Double Bend
Assembly Jig takes all the “guess” work
out of those difficult double bend putter assembly jobs.
GW1024 $34.99
$14.99
135
12/23/08
10:24 AM
Page 136
TOOLS – BENDING
RALPH MALTBY
GOLF CLUB MACHINE
The Golf Club Machine was designed for a production golf club
repair and assembly shop, where accuracy and flexibility are
requirements. With the use of the included Putter Leveling Block
(PBLP), the Golf Club Machine bends and measures irons and most
putters. Comes ready to be bolted to its floor stand.
FEATURES
• Fits left- and right-handed irons and putters
• Accurate and quick-measures iron loft, lie, offset and face
progression
• Precision protractor is accurate to 0.5°
• Hold-down clamp and Cambered Sole Secure Lock combine to
provide maximum hold-down pressure for secure bending
• Bending bar included
• Putter Leveling Block included
• Unit comes assembled, ready to be bolted to the included stand
• Includes a pad of 50 Custom Fitting Sheets
GAM
GAA
PBLP
Ralph Maltby Golf Club Machine (stand included) $399.99
Additional Data Recording Pad
$1.99
Putter Leveling Block (included)
$29.99
VALUE LINE GOLF CLUB MACHINE
Ideal for the part timer or the clubmaker getting started, our Value Line Golf Club Machine bends the loft and
lie angles of irons and putters. Designed to be held in a bench mounted vise, it has a robust clamping mechanism that fits many irons, and with the included Putter Leveling block, many putters. Can fit both right and
left-handed clubs.
Vise sold
separately
FEATURES
• Bending bar included
• Vise mounted
• Putter Leveling Block included
• Optional Brass Hosel Protector protects from marring (BHP)
VAM $149.99 Golf Club Machine
PBLP $29.99
Putter Leveling Block (included)
BHP
$1.99 pair Brass Hosel Protector (optional)
ECONOMY PUTTER
BENDING
MACHINE
This simple, vise-held machine gives clubmakers an economical way to bend virtually any
putter. Unique clamping mechanism holds putterhead securely. The vise mounting makes
this a must have for small shops with limited bench space. Bending bar included.
Does not include vise.
BPBM
$249.99
STRAIGHT NON-MARRING BENDING BAR
BNMB
$ 94.99
DOUBLE BEND BAR
MDBB
$ 39.99
NEW&
IMPROVED
SHORT HOSEL BENDING BAR
GW1036
136
$ 39.99
NEW&
IMPROVED
PUTTER LOFT
GAUGE
Putter loft is an important measurement
for fitting! This uniquelydesigned gauge allows for
quick and easy determination of the loft of any putter on
the market today. With loft
angles cut from 0-6°, this
handheld gauge is a must
for those who need a
quick and accurate putter loft measuring device.
PLCG
$14.99
12/23/08
10:25 AM
Page 137
BENDING – TOOLS
MALTBY PUTTER
BENDING MACHINE
The Maltby Putter Bending Machine was designed with the professional
clubmaker in mind. The machine needs no disassembly or special attachments
to safely clamp, bend and measure any right or left-hand putter head.
B
• Easily bends, clamps and measures right and left-hand putters.
• Heavy duty, CNC milled components.
• Universal design eliminates the need for special attachments or
disassembly regardless of the putter type. Traditional blade designs and
modern oversized high MOI putters are equally easy to securely clamp,
bend and measure.
• Smooth sliding protractor quickly and accurately measures the loft and lie
angles of all putters.
• Firm rubber, auto adjusting, soling pads help level the putter head and
protect the sole against dents and scratching during bending.
• Adjustable Brass Non-Marring Bending Bar included (BNMB).
• Double Bend Bar included
(MDBB).
• Can be bench or floor
mounted.
A
MA2012 $499.99
Bending Machine Includes BNMB (page 136)
MA2022
$27.99
Floorstand Parts Tray (optional)
MA2008S $199.99
Portable Stand
MPBMK $699.99 (SAVE $44.97!)
FULL KIT: Bending Machine, Floor Stand,
Double Bend Bar (MDBB), Straight
Non-Marring Bending Bar (BNMB)
RECOMMENDED MOUNTING OPTIONS:
A
B
MA2013
$29.99
Benchtop Mount Stand
MA2003AD $109.99
Floor Stand
137
12/23/08
10:25 AM
Page 138
TOOLS – BENDING
MALTBY IRON/HYBRID
BENDING MACHINE
The Maltby Iron/Hybrid Bending Machine will quickly and accurately bend any iron and also
safely bend hybrid models with at least a 3/4" length hosel. The addition of the hybrid attachment
makes the already “industry standard” bending machine a must have for all Professional Clubmakers.
FEATURES:
• Smooth sliding Protractor Assembly measures right or left-handed clubs for loft
and lie within 0.5°
• Unique Shaft Guide assures the shaft is in the proper position when recording loft
and lie readings
• New Brass Soling Discs securely clamps any iron, right or left-handed
• Brass clamping Top Jaw secures the head without marring the iron’s finish and
prevents slippage
• Brass Toe Stop helps prevent slippage
• Heavy duty T-Bar Bolt moves smoothly for quick, secure tightening of heads
• New Hybrid Rubber Top Jaw Attachment installs quickly to allow easy bending of
most hybrids
• Short Hosel Bending Bar included (GW1036)
• Protractor assembly easily adjusts in height to measure wedges with long hosels
• Adjustable, Non-Marring Brass Bending Bar included
(BNMB)
• Can be bench mounted or floor mounted with use of the New
GolfWorks Heavy Duty Machine Stand (preferred)
• Complete instructions included.
MA2017
$699.99
Maltby Design Iron Bending Machine
MA2003
$109.99
Floorstand (optional)
MA2022
$27.99
Floorstand Parts Tray (optional)
CHARGES REQUIRED DUE
TO WEIGHT.
• Bending an iron
138
• Bending a hybrid
12/23/08
10:26 AM
Page 139
BENDING – TOOLS
MALTBY PREMIUM GOLF
CLUB BENDING MACHINE
The Maltby Premium Golf Club Bending Machine
sets a new standard for craftsmanship,
ruggedness and performance.
Manufactured from high grade steel and aluminum, this machine is extremely sturdy.
Mounted to the Maltby Premium Heavy Duty floor stand (#MA2020), the user has full
360˚ access to the work at hand. The machines wide
base also allows it to be mounted to a work bench without any loss of stability. The quick change top clamp
mechanism allows you to change the top clamp in seconds to accommodate the bending of drivers, fairway woods, hybrids, irons or most
putters. The multiple bases needed for stabilizing heads during the
bending and measuring process can also be
changed in seconds by using the wrench (provided) and loosening one bolt. All parts that come in
contact with the clubhead are made of non-marring materials. The machines smooth, sliding loft
setting mechanism allows you to position each
club, from a putter through a driver,
with ease, without having to remove a
stabilizing pin. Once you are at the
setting needed, one quick tightening
turn and the setting is secure. The
smooth sliding protractor assembly
has an added feature of a height
adjuster, allowing you to position the
protractor for accurate measurements, no matter how long the hosel.
FEATURES:
• Multiple base and top jaw fixtures to
accommodate any type of golf club.
• Smooth sliding Protractor Assembly
measures right or left hand clubs for loft
and lie to within 0.5˚.
• Height adjustable Protractor Assembly for
measuring long hosel designs.
• Unique Shaft Guide assures the shaft is in
the proper position when taking loft and
lie readings.
• Measures any type of golf club – putters
(most models), wedges, irons, hybrids,
fairway woods and drivers, right or left
handed.
• Brass and rubber features on clamping
jaws and clamping bases prevent marring.
• Brass toe stop prevents slippage.
• Heavy-duty T-Bar bolt moves smoothly for
quick and secure tightening of heads.
• Quick tighten, one arm slide bolt allows for
quick transition from setting to setting,
without the need to remove a pin.
• Quick release rear bolt with speed turn
handle allows fast tightening of the nylon
non-marring back clamp.
• Can be bench mounted or use with the
Maltby Premium Heavy Duty floor stand
• Drivers & Fairways
• Hybrids
• Putters
• Wide Sole Irons
CHARGES REQUIRED DUE
TO WEIGHT.
MA2019
$1,299.99
Maltby Premium Golf Club Bending Machine
MA2020
$109.99
Maltby Premium Heavy-Duty Floorstand
(optional)
BNMB
$94.99
Brass Non-Marring Bending Bar
(optional)
GW1036 $39.99
Short Hosel Bending Bar
(optional)
MALTBY PREMIUM
GOLF CLUB BENDING
MACHINE KIT
• Maltby Premium Golf Club Machine
(MA2019 $1,299.99)
• Maltby Premium Heavy-Duty Floorstand
(MA2020 $109.99)
• Non-Marring Bending Bar (BNMB $94.99)
• Short Hosel Bending Bar (GW1036 $39.99)
SAVE $144.97
MA2021 $1,399.99
Maltby Premium Golf
Club Bending Machine Kit
139

tools - The GolfWorks

Transcription

Similar documents

Differential Air Shaft

A4 B-V sfondo:Layout 1

Light Options – There are 3 dual LED strips in the

TC-143 Service Manual - Fabco Automotive Corporation

Torre de Collserola

LONGFIELD™ 30 SPLINE Super Set

Join the Club! - The Golf Club at Hawks Prairie

SHAFTS

Golf Club Length - The Single Most Important

Borg-Warner T-10 Build/tips (Part 1)