Brochure - GS Global Resources
Transcription
Brochure - GS Global Resources
Electronic Suspended Pedal The WM-540 electronic suspended pedal is firewall mounted and designed to provide an electrical signal to an engine control module in response to the operator's demand for engine power. The WM-540 is equipped with a Hall-effect, non-contact sensor that can be programmed for analog output and/or integrated switches. The electronics are IP67 sealed and highly EMI resistant (SAE J1113). In addition, the unit can be customized with contact or PWM output sensors. The robust design includes corrosion resistant cast aluminum housing and a coated steel mounting bracket. Brackets can be modified to meet different mounting requirements. Standard bent steel lever rods can accommodate a variety of pedal placements, and a customized 3/16” steel plate lever is available for high static load requirements. SPECIFICATIONS PRODUCT LIFE Full Travel Cycles 5,000,000 ELECTRONICS Seal Integrity EMI Electronics IP67 sealed (IEC 60529) SAE J1113 Compliant ELECTRICAL Operating Voltage Output Signal 5V and 12V-24V Dual APS, Dual PWM, APS, PWM, APS/IVS PEDAL ANGLE Degrees Operating force 19.5° Angular Rotation Neutral = 55N, Full Travel = 75N MECHANICAL Static Load Vibration 1500N 3 hour, 3-axis, random broadband up to 4g ENVIRONMENTAL Operating Temp Range Storage Temp Range Humidity Sand/Dust -40°C to 85°C -40°C to 85°C 95% RH for 120 hours, 27°C to 75°C Tested to SAE J1455 MATERIALS Foot treadle & base plate Treadle cover Body castings Corrosion Resistant Plated Steel NBR Rubber Die-cast Aluminum Industrial Group MECHANICAL DIMENSIONS (mm) TYPICAL OUTPUT CHARACTERISTICS (other outputs are available) © 2014 Curtiss-Wright. All rights reserved. Specifications are subject to change without notice. All trademarks are property of their respective owners. USA Portland Oregon T: +1.509.684.8600 F: +1.503.684.3879 [email protected] www.cw-industrialgroup.com Europe Christchurch United Kingdom T: +44.1425.271444 F: +44.1425.272655 [email protected] www.cw-industrialgroup.com WM5 Asia Shanghai China T: +86.213.3310670 40-11/14 [email protected] www.cw-industrialgroup.com WCS-131507 Williams Customer Specification Original Release: 01/25/08 Original Project #: 328 • 1.0 Compliant with SEE SECTION 8.0 Features: • • • • • • • • • • • 2.0 19.5° Angular Rotation Single Ratiometric APS output Isolated APS/IVS functions Form C IVS output IP66 Sealed Sensor +5V Operation -40°C to + 85°C Operation Interfaces with Metripak 150-series Connector #12066317 with terminal pins #12103881-L Protected against Electrical Misconnection (indefinite duration) Steel Rod Lever Arm Steel Mounting Bracket Connector Pin Configuration Applications: • • • 3.0 The Celect ESPA is a firewallmounted Electronic Suspended Pedal Assembly. The application is for Diesel Trucks and Buses. Commonly applied to the following engines: • Cummins • Detroit Diesel III, IV, & V • International • Mack • MB NAFTA A B C D E F View Facing Connector End Pin A B C Function APSOUT APSGND APSVCC Pin D E F Function IVS2NO IVS1NC IVSCOM Description: The Celect ESPA is designed to provide an electrical signal to the engine control module in response to the operator’s demand for engine power. A sensor provides a linear voltage output proportional to the pedal angular displacement. It also provides an independent switched output that closes when the sensor is in the IDLE POSITION and a second output that closes ON THROTTLE ACTIVE. PROCEDURE NAME: DEPT: 030 Williams Customer Specification Form DOCUMENT NUMBER: QEMS Representative WQF-030-021 Mary Knight REVISION LEVEL: Process Owner 1 A DATE EFFECTIVE: Michael Cooper 11/13/07 DAF# Department Manager Scott Thiel 00396 WCS-131507 Absolute Maximum Electrical/Mechanical Ratings APS Circuit: Supply Voltage (VCC1, VCC2) Output Current (APS1, APS2 output) Short Circuit Duration – to GND or VCC +/-5.5V +/-10 mA Indefinite IVS Circuit: Supply Voltage Output Current (IVS output) Operating Temperature Storage Temperature Static Load Limit +/-5.5V +/-10 mA -40°C to +85°C -40°C to +85°C 489 N at the treadle pivot pin, centered horizontally on the treadle and normal to Pedal Rotation Operation of this device beyond absolute maximum ratings may result in permanent damage. Environmental Validation Thermal Cycle: Thermal Stress: Thermal Shock: Humidity: Vibration: Salt Fog: Dust Exposure: Chemical Immersion: Pressure Wash: Mechanical Shock: Refer to Williams Spec WDS-010 Mechanical Validation 5x106 1 Hz Full Stroke Cycles: Cycle Rate: PROCEDURE NAME: DEPT: 030 Williams Customer Specification Form DOCUMENT NUMBER: QEMS Representative WQF-030-021 Mary Knight REVISION LEVEL: Process Owner 2 A DATE EFFECTIVE: Michael Cooper 11/13/07 DAF# 00396 Department Manager Scott Thiel WCS-131507 Typical Output Characteristics PROCEDURE NAME: DEPT: 030 Williams Customer Specification Form DOCUMENT NUMBER: QEMS Representative WQF-030-021 Mary Knight REVISION LEVEL: Process Owner 3 A DATE EFFECTIVE: Michael Cooper 11/13/07 DAF# 00396 Department Manager Scott Thiel WCS-131507 Mechanical Dimensions and Characteristics (for reference only) PROCEDURE NAME: DEPT: 030 Williams Customer Specification Form DOCUMENT NUMBER: QEMS Representative WQF-030-021 Mary Knight REVISION LEVEL: Process Owner 4 A DATE EFFECTIVE: Michael Cooper 11/13/07 DAF# 00396 Department Manager Scott Thiel WCS-131507 Applications Information: Referenced Documents: • • Williams Controls DWG #131507 Williams Controls Specification # WDS-010 Revision History Rev A Date 01/18/08 ECN# 41818 Checked WJ Approved D. Holt Changes/Comments Initial Release Williams Controls 14100 S.W. 72nd Avenue Portland, OR. 97224 Phone (503) 684-8600 Fax (503) 624-3812 Email [email protected] PROCEDURE NAME: DEPT: 030 Williams Customer Specification Form DOCUMENT NUMBER: QEMS Representative WQF-030-021 Mary Knight REVISION LEVEL: Process Owner 5 A DATE EFFECTIVE: Michael Cooper 11/13/07 DAF# 00396 Department Manager Scott Thiel