Desoutter Air Motor Catalogue

Transcription

Desoutter Air Motor Catalogue
TM
Air Motors
Desoutter Limited Eaton Road Hemel Hempstead Hertfordshire HP2 7DR telephone +44 1442 344300 facsimile +44 1442 344604
Air
Motors
TM
Introduction
2.
Desoutter Limited Eaton Road Hemel Hempstead Hertfordshire HP2 7DR telephone +44 1442 344300 facsimile +44 1442 344604
Air motors are versatile power sources which can
be used to power many kinds of operations
requiring a rotational drive. They have many
advantages over electric motors, and often become
the only feasible method of operation.
Advantages
Desoutter offers a wide range of
rotating vane type air motors
within a power range of 0.26 kW
(0.35 hp) to 0.66 kW (0.85 hp).
Most motors can be supplied as
single rotation or reversible.
Reversible motors have keyed
shafts, while single direction
motors can be supplied with
threaded shafts or alternatives.
1. Compact, with high power to
weight ratio. An air motor will
often be one third or less
than the size of a comparable
electric motor. An air motor
can be used in a portable
application where the weight
and/or physical size of the
electric motor would preclude
portable operations. For
example, a 0.63 kW (0.85 hp)
air motor running at 2000 rpm
weighs 1.4 kg (3 lbs) and is
approximately 200mm (8")
long and just over 50mm (2")
in diameter.
2. The output speed and torque
can be simply controlled by
regulating either the air
pressure or air flow. No
expensive control equipment
is required.
3. If a motor is loaded to a
stalled condition, and held
there for any length of time,
no damage is caused to the
motor. In certain applications,
such as tightening fasteners,
one acceptable method of
control is to regulate the air
pressure so that the motor
stalls at the required torque.
4. When the load is released,
the air motor will reach free
running speed usually within
one third to one half of a
revolution.
5. No risk of overheating either
when continuously run or
frequent stop/starts or
reversing. Note that this
condition assumes the use of
an inline lubrication system.
6. Reversing motors require
simple control of air pressure
into ports in the control top
of the motor to determine
direction of rotation. To
reverse the direction of
rotation takes milliseconds to
complete.
7. Resists moisture, dust, heat. Is
generally explosion proof and
can be used safely in most
hazardous situations.
Terms
The following terminology is
used in this publication:
No load speed – maximum
speed attained at a given air
pressure under a no-load
condition.
Maximum power – with a vane
type air motor, the maximum
power output is achieved at
nearly one half of the no load
speed. This is the point at which
the motor will run most
efficiently.
Dynamic torque – the output
torque of the motor at any stage
during the operating cycle. The
dynamic torque increases
virtually in a straight line from
zero at no load to a maximum at
the stalled condition.
Stall torque – output torque
achieved when the load applied
causes the motor to stall.
Starting torque – to obtain the
proper sealing of the rotor
blades against the cylinder walls
for maximum efficiency, and to
overcome inertia, it takes more
torque to start an air motor than
when it is running. Starting
torque is approximately 75% of
stall torque.
Air consumption – measured in
the no-load condition. Air
consumption is maximum at no
load, and is approximately three
quarters of this figure at maximum
power. Air consumption reduces
as the working air pressure is
reduced. For example at 50 p.s.i.
the air consumption is almost
one half that at 90 p.s.i.
Performance specifications –
are normally shown with an air
inlet pressure of 6.3 bar at the air
motor, unless otherwise stated.
Note that there is approximately
a 14% drop in power for every
10% reduction in air inlet
pressure.
Rotation – non-reversible motors
rotate in a clockwise direction if
the motor is viewed from the air
inlet end with the spindle
pointing away from you.
Contents
TM
3. Desoutter Limited Eaton Road Hemel Hempstead Hertfordshire HP2 7DR telephone +44 1442 344300 facsimile +44 1442 344604
Contents
4
5
Selecting an Air Motor
DM6/DM65 Series
(0.26 kW, Non Reversible, Torque 0 - 8 Nm)
6
2DM6 Series
(0.26 kW, Reversible, Torque 0 - 8 Nm)
7
HM Series
(0.45 kW, Non Reversible, Torque 0 - 41 Nm)
8
HM55 Series
(0.63 kW, Non Reversible, Torque 0 - 41 Nm)
9
2HM5 Series
(0.66 kW, Reversible, Torque 0 - 41 Nm)
10
2H410 Series
(0.66 kW, Reversible, Worm Drive)
11
Air Motors for Special Applications and
Application Questionnaire
12
Air Motor Accessories
15
Air Motor Control Equipment
General Information
• Air Motors are supplied as “Machinery to be incorporated” – Customer is
responsible for safe incorporation into the complete machine.
• Always refer to Operating and Warning instructions supplied with the tool before
operating the tool.
• All accessories and those tools marked with an asterisk (*) are supplied outside the
scope of Desoutter Ltd’s ISO9001 registration, but are sourced from firms meeting
Desoutter Ltd’s supplier quality assurance requirements.
• Sound levels quoted in this catalogue were obtained from measurements made
according to the CAGI-PNEUROP Test Code. Nominal values are quoted, sound
levels of individual tools may vary by ±2dB(A).
Selecting an Air Motor
TM
4.
Desoutter Limited Eaton Road Hemel Hempstead Hertfordshire HP2 7DR telephone +44 1442 344300 facsimile +44 1442 344604
After first determining
whether a single direction or
a reversible motor is required,
the next step is to consider
the required output speed
and torque together with the
operational conditions.
As a general rule try to select
a motor with twice the free
running speed of the speed
required under load.
By using the performance
graphs indicated on the
following pages it is then
possible to ensure that the
motor meets the requirements
specified.
Example: What motor is
required to
produce an output
torque of 6 Nm at
300 rpm. The
motor should be
reversible and 6
bar supply pressure
is available.
Step One – Select the
motor type
The maximum dynamic
torque of the DM Series
motor is 8 Nm. Since a
reversible motor is required
the 2DM6 will be used.
Step Two – Select the
appropriate motor speed
As a rule try to select a
motor with twice the free
running speed of the speed
required since this will
usually coincide with the
high power band of the
motor.
Step Three – Confirm the
motor is suitable for the
application
By plotting both the torque
(6 Nm) and speed (300 rpm)
on the graph an intersection
is found.
Provided the intersection is
below the torque line for the
motor (straight line) then the
motor is suitable for the
application.
For this example we require
300 rpm so use a motor of
about 600 rpm free running
speed. The closest is 620 rpm
so try the 2DM6-620.
2DM6 Series Air Motors
*
*
*
*
*
*
*
7
4
2.5
1.2
0.6
0.3
*
*
*
*
*
*
*
5.85
3.34
2.05
1
0.5
0.25
*
*
*
*
*
*
8
4.68
2.67
1.64
0.8
0.4
0.2
*
*
*
*
*
*
6
3.51
2
1.23
0.6
0.3
0.15
*
*
*
*
*
6.66
4
2.34
1.64
0.82
0.4
0.2
* Dynamic torque must not exceed 8 Nm (5.9lbf ft).
0.1
0.05
Power kW
0
0
0
0
0
0
0
0
0
0
0
0
0
Torque Nm
Power at an inlet pressure of 6.3 bar.
*
*
*
5.83
5
3.33
2
1.17
0.67
0.41
0.2
0.1
45
60
90
290
390
620
960
1650
2700
4200
9000
16000
Reversible
0
0
0
0
0
0
0
0
0
0
0
0
2000
1100
400
300
180
110
66
40
30
10
6
5
4000
2200
800
600
360
220
130
90
70
20
13
10
6000
3300
1300
900
540
330
200
130
100
30
20
15
8000
4400
1800
1200
720
440
260
180
130
40
26
20
10000
5500
2300
1500
900
550
330
220
170
50
33
25
Speed r/min
12000
6600
2700
1800
1060
660
400
260
200
60
40
30
14000
7700
3200
2100
1260
770
460
310
230
70
46
35
16000
8800
3600
2400
1440
880
530
350
270
80
53
40
18000
9900
4000
2700
1620
990
600
400
300
90
60
45
16000
9000
4200
2700
1650
980
620
390
290
90
60
45
DM6, DM65 Series
Desoutter Limited Eaton Road Hemel Hempstead Hertfordshire HP2 7DR telephone +44 1442 344300 facsimile +44 1442 344604
DM6, DM65 Series
0.26 kw (0.35 hp),
Maximum Torque 8 Nm
(5.9 lbf ft), Non Reversible
MOTOR TYPE
THREADED SHAFT
THREADED NOSE
/
DM6-16000T
DM6-9000T
DM6-4200T
DM6-2700T
DM6-1650T
DM6-980T
DM6-620T
DM6-390T
DM6-290T
DM6-90T
DM6-60T
DM6-45T
NO LOAD
SPEED
MAX. POWER
TORQUE AT
MAX. POWER
AIR CONSUMPTION
AT MAX. POWER
MIN. HOSE
BORE
WEIGHT
SOUND LEVEL
r/min.
kW
Nm
l/s
mm
kg
dB(A)
0.26
0.23
0.4
1.2
1.8
3
5
8
8
8
8
8
8
10
0.65
0.65
0.65
0.65
0.75
0.75
0.75
0.75
0.83
0.83
0.83
0.93
76
16000
9000
4200
2700
1650
980
620
390
290
90
60
45
9.4
Power at an inlet pressure of 6.3 bar.
* Dynamic torque must not exceed 8 Nm (5.9lbf ft).
*
*
*
*
*
*
*
7
4
2.5
1.2
0.6
45
60
90
290
390
620
960
1650
2700
4200
9000
16000
DM65-16000T
DM65-9000T
DM65-4200T
DM65-2700T
DM65-1650T
DM65-980T
DM65-620T
DM65-390T
DM65-290T
DM65-90T
DM65-60T
DM65-45T
KEYED SHAFT /
THREADED NOSE
*
*
*
*
*
*
*
5.85
3.34
2.05
1
0.5
0.3
*
*
*
*
*
*
6
3.51
2
1.23
0.6
0.3
0.25
Power
0.2
0.15
*
*
*
*
*
6.66
4
2.34
1.64
0.82
0.4
0.2
4b
ar
(58
psi
)
Power kW
0.1
2 ba
r (24
psi)
*
*
*
5.83
5
3.33
2
1.17
0.67
0.41
0.2
0.1
0.05
0
0
0
0
0
0
0
0
0
0
0
0
0
2000
1100
400
300
180
110
66
40
30
10
6
5
4000
2200
800
600
360
220
130
90
70
20
13
10
6000
3300
1300
900
540
330
200
130
100
30
20
15
8000
4400
1800
1200
720
440
260
180
130
40
26
20
10000
5500
2300
1500
900
550
330
220
170
50
33
25
12000
6600
2700
1800
1060
660
400
260
200
60
40
30
14000
7700
3200
2100
1260
770
460
310
230
70
46
35
16000
8800
3600
2400
1440
880
530
350
270
80
53
40
18000
9900
4000
2700
1620
990
600
400
300
90
60
45
16000
9000
4200
2700
1650
980
620
390
290
90
60
45
Speed r/min
Max Loading
550N
DM6-T
Exhaust Collector can be mounted with silencer facing in
either direction and rotated through 360° - 1/4" BSP thread.
1/8" BSP
Air inlet
3
Ø10(h6)
M35 x 1.0 L.H.
12
7
45
Ø36
1.2
13
Optional
Adaptor
for
1/8" NPT
Air Inlet
23.5
40.5
Tapped hole M4 x 13
3
14
A
Ø38
38
7
DM65-T
M35 x 1.0 L.H.
Torque Nm
*
*
*
*
*
*
8
4.68
2.67
1.64
0.8
0.4
To
rqu
e
6b
ar
(87
psi
)
0
0
0
0
0
0
0
0
0
0
0
0
5.
TM
12
3/8" X 24 UNF
35
3
All dimensions in mm unless specified otherwise
SPEED
A
16000, 4200, 2700
9000
1650, 980, 620, 390
290, 90, 60
45
130.0
163.4
152.0
170.0
188.2
2DM6 Series
TM
6.
Desoutter Limited Eaton Road Hemel Hempstead Hertfordshire HP2 7DR telephone +44 1442 344300 facsimile +44 1442 344604
2DM6 Series
0.26 kw (0.35 hp),
Maximum Torque 8 Nm
(5.9 lbf ft), Reversible
MOTOR TYPE
2DM6-16000
2DM6-9000
2DM6-4200
2DM6-2700
2DM6-1650
2DM6-980
2DM6-620
2DM6-390
2DM6-290
2DM6-90
2DM6-60
2DM6-45
MAX. POWER
TORQUE AT1)
MAX. POWER
AIR CONSUMPTION
AT MAX. POWER
MIN. HOSE
BORE
WEIGHT
SOUND
r/min.
kW
Nm
l/s
mm
kg
dB(A)
0.26
0.23
0.4
1.2
1.8
3
5
8
8
8
8
8
8
10
0.6
0.6
0.6
0.6
0.7
0.7
0.7
0.7
0.78
0.78
0.78
0.88
731)
16000
9000
4200
2700
1650
980
620
390
290
90
60
45
9.4
It is recommended that a suitable air diffuser is fitted downstream of any control valve through which exhaust air exits.
Power at an inlet pressure of 6.3 bar.
* Dynamic torque must not exceed 8 Nm (5.9lbf ft).
*
*
*
*
*
*
*
7
4
2.5
1.2
0.6
45
60
90
290
390
620
960
1650
2700
4200
9000
16000
1)
NO LOAD SPEED
*
*
*
*
*
*
*
5.85
3.34
2.05
1
0.5
0.3
*
*
*
*
*
*
6
3.51
2
1.23
0.6
0.3
4b
0.25
Power
0.2
0.15
ar (
58p
*
*
*
*
*
6.66
4
2.34
1.64
0.82
0.4
0.2
si)
Power kW
Torque Nm
*
*
*
*
*
*
8
4.68
2.67
1.64
0.8
0.4
To
rq
6 b ue
ar
(87
psi
)
0.1
*
*
*
5.83
5
3.33
2
1.17
0.67
0.41
0.2
0.1
2 bar (2
9psi)
0.05
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
2000
1100
400
300
180
110
66
40
30
10
6
5
4000
2200
800
600
360
220
130
90
70
20
13
10
6000
3300
1300
900
540
330
200
130
100
30
20
15
8000
4400
1800
1200
720
440
260
180
130
40
26
20
10000
5500
2300
1500
900
550
330
220
170
50
33
25
12000
6600
2700
1800
1060
660
400
260
200
60
40
30
14000
7700
3200
2100
1260
770
460
310
230
70
46
35
16000
8800
3600
2400
1440
880
530
350
270
80
53
40
18000
9900
4000
2700
1620
990
600
400
300
90
60
45
16000
9000
4200
2700
1650
980
620
390
290
90
60
45
Speed r/min
max. loading
550N
Ø38
Ø7
12
60
3
Ø10(h6)
48CRS
Forward
Optional
Adaptor
for
1/8" NPT
Air Inlet
Reverse
Tapped hole M4 X 13
1.2
Air inlet
Forward Rotation
9.2
9
Ø37
(f7)
3
Air Inlet
Reverse Rotation
9.2
Ø36
5.2
13
23.5
3 Ports
1/8" BSP
29(f7)
Note: Exhaust is through common exhaust
port and opposite rotation inlet port.
Blocking or restricting these ports
will reduce the performance of the
motor.
14
24.5
36
Exhaust
7.5
A
All dimensions in mm unless specified otherwise
SPEED
A
16000, 4200, 2700
9000
1650, 980, 620, 390
290, 90, 60
45
127.1
160.5
149.1
167.1
185.3
HM Series
Desoutter Limited Eaton Road Hemel Hempstead Hertfordshire HP2 7DR telephone +44 1442 344300 facsimile +44 1442 344604
HM Series
0.45 kw (0.6 hp),
Maximum Torque 41 Nm
(30 lbf ft), Non Reversible
MOTOR TYPE
HM-4600
HM-2850
HM-1900
HM-830
HM-500
HM-340
HM-90
HM-60
NO LOAD SPEED
MAX. POWER
TORQUE AT
MAX. POWER
AIR CONSUMPTION
AT MAX. POWER
MIN. HOSE
BORE
WEIGHT
SOUND
r/min.
kW
Nm
l/s
mm
kg
dB(A)
0.45
2.0
3.0
4.5
10.4
16.8
25
41
41
10
1.1
1.1
1.1
1.6
1.6
1.6
1.9
1.9
82
4600
2850
1900
830
500
340
90
60
13
* Dynamic torque must not exceed 41 Nm (30lbf ft).
To
rqu
e
*
*
*
32.40
20.00
8.70
5.80
3.60
60
90
340
500
830
1900
2850
4600
Power at an inlet pressure of 6.3 bar.
*
*
29.10
19.44
12.00
5.22
3.48
2.16
0.5
Power
(87
ps
i)
0.4
0.3
4b
ar
(58
*
*
19.40
12.96
8.00
3.48
2.32
1.44
psi
2b
*
37.40
9.70
6.48
4.00
1.74
1.16
0.72
ar (
)
Power kW
0.2
29p
0.1
si)
0
0
0
0
0
0
0
0
0
557
345
230
100
62
41
11
7
1114
690
460
200
123
82
21
14
1670
1034
690
300
185
124
32
21
2227
1379
920
400
247
165
43
29
2782
1724
1149
500
309
206
53
36
3339
2069
1379
600
370
247
64
43
3895
2414
1609
700
432
289
75
50
4452
2759
1839
800
494
330
86
57
4600
2850
1900
830
500
340
90
60
Speed r/min
Ø9
15.5
9.5
Air inlet 1/4" BSP
(1/4" NPT optional)
Ø 47.5
70 CRS
89
Ø 49.2 (f7)
11/2" X 20 TPI LH
Ø 62
12.7
HM-4600
HM-2850
HM-1900
11/2" X 20 UNF
56
51
9
26.5
14
10
4.8
A
14
Ø9
16
Exhaust
9
5/8" X
9.5
4.8
A
All dimensions in mm unless specified otherwise
HM-830
HM-500
HM-340
HM-90
HM-60
16 UN
56
51
Ø 62
Ø 47.5
89
70 CRS
15/8" X 16 TPI LH
Ø 49.2 (f7)
Torque Nm
*
*
38.80
25.92
16.00
6.96
4.64
2.87
6b
ar
0
0
0
0
0
0
0
0
7.
TM
26.5
14
10
SPEED
A
HM-4600, 2850, 1900 111.3
HM-830, 500, 340
156.3
HM-90, 60
193.3
HM55 Series
TM
8.
Desoutter Limited Eaton Road Hemel Hempstead Hertfordshire HP2 7DR telephone +44 1442 344300 facsimile +44 1442 344604
HM 55 Series
0.63 kw (0.85 hp),
Maximum Torque 41 Nm
(30 lbf ft), Non Reversible
THREADED SHAFT
MAX. POWER
TORQUE AT
MAX. POWER
AIR CONSUMPTION
AT MAX. POWER
MIN. HOSE
BORE
WEIGHT
SOUND
r/min.
kW
Nm
l/s
mm
kg
dB(A)
0.63
0.60
3.5
5.2
12.0
19.4
29.1
41
41
41
10
1.4
1.4
1.4
1.7
1.7
1.7
2.1
2.1
2.1
78
18000
3300
2100
950
550
350
150
100
40
15.5
Power at an inlet pressure of 6 bar.
40
100
150
350
550
950
2100
3300
18000
HM55-18000
HM55-3300
HM55-2100
HM55-950
HM55-550
HM55-350
HM55-150
HM55-100
HM55-40
NO LOAD SPEED
*
*
*
*
*
28.00
12.18
8.12
1.40
* Dynamic torque must not exceed 41 Nm (30lbf ft).
*
*
*
*
38.88
24.00
10.44
6.96
1.20
0.7
0.5
*
*
*
38.80
25.92
16.00
6.96
4.64
0.80
*
*
*
*
32.40
20.00
8.70
5.80
1.00
Power
0.4
0.3
(58
psi
)
*
*
*
19.40
12.96
8.00
3.48
2.32
0.40
*
*
*
29.10
19.44
12.00
5.22
3.48
0.60
4b
ar
Power kW
0.2
*
37.40
23.00
9.70
6.48
4.00
1.74
1.16
0.20
2b
ar (
29p
si)
0.1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
2000
345
230
100
62
41
17
11
5
4000
690
460
200
123
82
35
21
10
6000
1034
690
300
185
124
52
32
14
8000
1379
920
400
247
165
70
43
19
10000
1724
1149
500
309
206
87
53
24
12000
2069
1379
600
370
247
104
64
29
14000
2414
1609
700
432
289
122
75
33
16000
2759
1839
800
494
330
139
86
38
18000
3103
2069
900
556
371
157
96
43
18000
3300
2100
950
550
350
150
100
40
Speed r/min
C
Exhaust Collector can be mounted with silencer facing in
either direction and rotated through 360° - 1/4" BSP thread.
Ø53(f8)
B
Ø25.4
Ø40(h6)
D
Ø52
Ø9
70 CRS
Torque Nm
0.6
To
rqu
e
6b
ar
(87
psi
)
4.5
21.5 A/F
4.5
10
4.7
Ø54
A
54.5
Air Inlet 1/4 " BSP
(1/4" NPT Optional)
MOTOR TYPE
A
THREAD B
18000
159
1/2" x 20 UNF
2100, 3300
350, 550, 950 196.5 5/8" x 16 UN
40, 100, 150 234
5/8" x 16 UN
C
D
23.3 12.3
28.4 16.2
28.4 16.2
2HM5 Series
9.
TM
Desoutter Limited Eaton Road Hemel Hempstead Hertfordshire HP2 7DR telephone +44 1442 344300 facsimile +44 1442 344604
2HM5 Series
0.66 kw (0.85 hp),
Maximum Torque 41 Nm
(30 lbf ft), Reversible
MOTOR TYPE
MAX. POWER
TORQUE AT
MAX. POWER
AIR CONSUMPTION
AT MAX. POWER
MIN. HOSE
BORE
WEIGHT
SOUND
r/min.
kW
Nm
l/s
mm
kg
dB(A)
0.65
0.65
3.8
5.6
13
21
31.5
41
41
41
10
1.4
1.4
1.4
1.7
1.7
1.7
2.1
2.1
2.1
87
18000
3300
2100
950
550
350
150
100
40
16.5
Power at an inlet pressure of 6 bar.
* Dynamic torque must not exceed 41 Nm (30lbf ft).
*
*
*
*
*
28.00
12.18
8.12
1.40
40
100
150
350
550
950
2100
3300
18000
2HM5-18000
2HM5-3300
2HM5-2100
2HM5-950
2HM5-550
2HM5-350
2HM5-150
2HM5-100
2HM5-40
NO LOAD SPEED
0.7
*
*
*
*
38.88
24.00
10.44
6.96
1.20
To
rq
6b
ar
ue
7p
0.5
*
*
*
38.80
25.92
16.00
6.96
4.64
0.80
*
*
*
*
32.40
20.00
8.70
5.80
1.00
si)
0.4
ar
(58
psi
0.3
)
*
*
*
19.40
12.96
8.00
3.48
2.32
0.40
*
*
*
29.10
19.44
12.00
5.22
3.48
0.60
4b
Power kW
Torque Nm
0.6
Power
(8
0.2
2b
ar (
*
37.40
23.00
9.70
6.48
4.00
1.74
1.16
0.20
29p
si)
0.1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
2000
345
230
100
62
41
17
11
5
4000
690
460
200
123
82
35
21
10
6000
1034
690
300
185
124
52
32
14
8000
1379
920
400
247
165
70
43
19
10000
1724
1149
500
309
206
87
53
24
12000
2069
1379
600
370
247
104
64
29
14000
2414
1609
700
432
289
122
75
33
16000
2759
1839
800
494
330
139
86
38
18000
3103
2069
900
556
371
157
96
43
18000
3300
2100
950
550
350
150
100
40
Speed r/min
Ø54
30
Ø9
Ø52
Ø53 (f8)
C
D
ØB
Ø17
Ø40 (h6)
70 CRS
90
Forward
Note: Exhaust is through common exhaust
port and opposite rotation inlet port.
Blocking or restricting these ports will
reduce the performance of the
motor.
Reverse
3 Ports
1/4" BSP
(1/4" NPT Optional)
Trapped hole 'E'
20
4.5
Exhaust
10
4.5
35
4.7
A
13 CRS
All dimensions in mm unless specified otherwise
MOTOR TYPE
8
Air Inlet
Forward
Rotation
13 13
Air Inlet
Reverse
Rotation
A
B(h6) C
18000
143.5 12
2100, 3300
350, 550, 950 187
14
40, 100, 150 224.5 14
D
E
1.5
4
M4
2
2
5
5
M5
M5
TM
2H410 Series
10.
Desoutter Limited Eaton Road Hemel Hempstead Hertfordshire HP2 7DR telephone +44 1442 344300 facsimile +44 1442 344604
2H410 Series
0.66 kw (0.85 hp),
Maximum Torque 106 Nm
(78 lbf ft), Worm Drive
Motors
MOTOR TYPE
2H410-500
2H410-350
2H410-150
2H410-90
2H410-60
NO LOAD SPEED
MAX. POWER
MAX. STALL
TORQUE
MIN. SAFE WORKING
PRESSURE
MAX. AIR
CONSUMPTION
MIN. HOSE
BORE
WEIGHT
SOUND
r/min
kW
Nm
bar
l/s
mm
kg
dB(A)
0.66
39
51
102
102
102
6
6
6
4
2.8
17
17
17
10
9
12
12
12
10
10
1.7
1.7
2.0
2.0
2.0
87
500
350
150
90
60
A version of the 2HM5 motor
can be supplied equipped
with a worm drive gearbox,
allowing the drive to be
taken from each side of the
head for either right hand or
left hand rotation.
Standard drive is a .525" A/F
Female Hexagon, but
adaptors can be supplied to
convert this to either 3/8" or
1/2" square drive. An
alternative head is available
to provide a No. 1 morse
taper drive.
A
68.3
Note: Exhaust is through common exhaust
port and opposite rotation inlet port.
Blocking or restricting these ports will
reduce the performance of the motor.
B
21.6 18
Exhaust Port
3/8"BSP
RAD
Ø 52.1
52.1
26 2
527" A/F Interna Hexagon Thro
Ø 50.8
Left Hand
Rotation
This Side
Right Hand
Rotation
This Side
30.7
9.5
Reverse Port
Forward Port 1/4"BSP
1/4"BSP
Ø 51.6
TYPE
SPEED
A
B
2H410-500
2H410-350
2H410-150
2H410-90
2H410-60
500
350
150
90
60
208.8
208.8
245.9
245.9
245.9
118.9
118.9
156.0
156.0
156.0
Special Applications and Application Questionnaire
11.
TM
Desoutter Limited Eaton Road Hemel Hempstead Hertfordshire HP2 7DR telephone +44 1442 344300 facsimile +44 1442 344604
Special
Applications
Desoutter can produce
special motors to specifically
suit your application whether
through modification of the
control method or output
drive. Please provide details
should your application
require a special type.
Selection Questionnaire
The following questionnaire is for use either by the engineer for his/her own calculations or can
be completed and returned to the local Desoutter Sales Office.
Specification
Torque Required
Nm
Speed Required
RPM
Rotation
Output Type
(to convert lbfft to Nm x 1.356)
Forward
Reverse
Reversible
Keyed
(DM6-T/2DM6/2HM5)
Threaded
(DM65-T/HM55/HM only)
0.525" Hexagon
(2H410 only)
bar
(to convert psi to bar x 14.504)
Air Line Pressure
Lubrication Available
Yes No Number of Motors Required
OFFICE USE ONLY
Recommended Motor Type
OFFICE USE ONLY
Accessories (see pages 12-15)
Recommended Accessories
Chucks
Collet Holders
Screwdriver Bit Adaptor
Flange (DM6/65-T)
Exhaust Collector (HM)
Stands
Air Service Equipment
Air Line Hoses
Output Accessories
TM
12.
Desoutter Limited Eaton Road Hemel Hempstead Hertfordshire HP2 7DR telephone +44 1442 344300 facsimile +44 1442 344604
Key Adjustable Chucks
MOTOR TYPE
CHUCK CAPACITY
CHUCK AND KEY
mm
part no.
6.5
8
10
28942
94502
31132
HM-1900-4600
HM55-2100-18000
13
29142
HM-60-830
HM55-40-950
13
29122
DM65-T
Collet Chucks
MOTOR TYPE
LENGTH
DIA.
1
2
mm
mm
part no
part no
26932
26942
42
15.2
26932
26952
DM65-T
HM-1900-4600
HM55-2100-18000
COLLETS
mm
part no.
mm
part no.
mm
part no.
mm
part no.
0.8
0.9
1.0
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
2892
2902
2912
2922
2932
2942
2952
2962
2972
2982
2992
1.9
2.0
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
3002
3012
3022
3032
3042
3052
3062
3072
3082
3092
3102
3.0
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
4.0
3112
3122
3132
3142
3152
3162
3172
3182
3192
3202
3212
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
5.0
3222
3232
3242
3252
3262
3272
3282
3292
3302
3312
Fixed Collet Drives
DIAMETER
MOTOR TYPE
6mm
1/4"
DM65-T
DRIVE
MOTOR TYPE
LENGTH
DIA.
COLLET
NUT
mm
mm
part no.
part no.
41.3
41.3
21
21
22362
22382
22352
22352
Screwdriver Bit Adaptor
5/16" fem.
DM65-T
LENGTH
DIA.
mm
mm
part no.
35
13
27532
Thread Adaptor
MOTOR TYPE
A
B
DM65-T
3/8" x 24 UNF
1/2" x 20 UN
part no.
A
B
68143
Output Accessories
13.
TM
Desoutter Limited Eaton Road Hemel Hempstead Hertfordshire HP2 7DR telephone +44 1442 344300 facsimile +44 1442 344604
Flange for DM6/65-T
R8
2 HOLES Ø7
Ø 38
Ø 44.5
20.0
17
13
16
7.1
4.1
73.2
M35 -1.O LH 6H
Ø41.22
Ø41.28
Part No.
286423
5.5
Ø37.0
4.5
M35 -1.O LH 6H
Part No.
441653
Ø41.224
Ø41.275
Ø37.0
Ø34.90
Ø34.85
8
44.5
M35x1.OP LH 6H
390683/390693 – 15
441653 – 19
Part No.
390683
M35x1.OP LH 6H
Ø37.0
Part No.
390693
7.9 RAD
57.2 CRS.
57.15
50.8
44.5
20.0
17
13
2 HOLES Ø7
R6
48 CRS.
2 HOLES Ø7
Ø28.98
Ø28.96
2 HOLES Ø7
R8
7.5
8
2.29
Part No. 390683 provides same mounting dimensions as DM – 17700/5300/4000/3000/1600
Part No. 390693 provides same mounting dimensions as DM – 900/500/210/80/40
Part No. 441653 provides same mounting dimensions as DM6 and DM65 motors
Exhaust Collector Ring for HM Series
Part No. 43093
Part No. 72163
CONNECTION
PART NO.
Ø15mm barb
3/8" BSP Female
43093
72163
Stands
R55 Lever Operated Stand for HM Series
Note: Motor must be fitted with exhaust
collector ring (see above)
203mm
31.8mm
(1.25")
453mm
235mm
203mm
127mm
42mm
12.7mm
Part No. 903304
Air Motor Accessories
TM
14.
Desoutter Limited Eaton Road Hemel Hempstead Hertfordshire HP2 7DR telephone +44 1442 344300 facsimile +44 1442 344604
D54 Lever-Operated Stand
R55-S Lever-Operated Stand
For DM6, DM65 and 2DM6 Motor
Part No. 901944
Weight: 7 kg
Max. Stroke: 45mm
Part No. 903644
Weight: 11.32 kg
Max. Stroke: 57mm
Max. Mounting Plate Load: 6 kg
290
38
610
approx.
58.5
Height
Adjustment
405
SelfStart
plunger
255
Mounting
Plate
Height
Adjustment
Stroke
Adjustment
76
322
Max.
approx
38
Stroke
Adjustment
73
178
25.4
19
172
42
203
9.5
41.3
44.5
102
19
44.5
209
19
25.4
102
203
9.5
51
127
19
51
12.7
235
Ø32
102
100
12.7
M55A Lever-Operated Stand
MC55 Cylinder-Operated Stand
With Linear Bearings
With Linear Bearings
Part No. 902594
Weight: 16 kg
Max. Stroke: 65mm
Max. Mounting Plate Load: 7.25 kg
Part No. 902914
Weight: 32 kg
Max. Stroke: 100mm
Max. Mounting Plate Load: 68 kg
380 Standard
230 Optional
220
1041
approx.
50
SelfStart
plunger
250
Mounting
Plate
Height
Adjustment
90
1020
179
Stroke
Adjustment
Max
743
approx.
178
250
646
Max
approx.
40
51
40
51
358
358
Ø30
Ø30
312
312
305
102
157
12.7
335
305
102
157
12.7
335
Control Equipment
15.
TM
Desoutter Limited Eaton Road Hemel Hempstead Hertfordshire HP2 7DR telephone +44 1442 344300 facsimile +44 1442 344604
Operating the
Motor
A Typical Control Circuit
To obtain the longest life
span of the vane type air
motor, it is recommended
that a clean, dry supply of air
in sufficient quantity is
supplied, with an automatic
lubrication system to provide
the correct amount of
lubrication to the air motor
at all times.
Reversible
Motor
Control
Valve
Forward Port
Flow Regulators
Reverse Port
Controlling the motor can be
achieved using pneumatic
valves, either hand, foot,
pilot air or solenoid operated.
The valve used must have full
flow capability to ensure
unrestricted air flow to the
motor.
Exhaust Port
Silencer
Filter, Regulator,
Lubricator
Air Supply
Torque is controlled by
changing the pressure, speed
by air flow.
Flow
Regulators*
Reinforced PVC Air Hose*
A
B
C
HOSE BORE
A THREAD
mm
PART SIZE
PART NO.
1/4" BSP Female
90882
Adaptors*
Hose assembly tested to 12.6 bar air pressure.
10
10
12
12
12
1/4"
1/4"
3/8"
1/2"
1/2"
BSP
BSP
BSP
BSP
BSP
B THREAD
C LENGTH
TYPICAL FLOW PART NO.
BSP
m
l/s
1/4"
1/4"
3/8"
1/2"
1/2"
3
5
3
3
5
14
14
33
33
33
75972
75982
78532
76002
76022
Air Line Service Sets*
A
Filter, Regulator, Lubricator
– Air Preparation unit comprising:
Filter-Water Separator
Pressure Regulator
Oil Mist Lubricator
Mounting Bracket
B
PART SIZE
PART NO.
RECOMMENDED AIR FLOW
l/s
A THREAD
B THREAD
PART NO.
1/8"
1/8"
1/8"
1/4"
1/4"
3/8"
1/4"
1/2"
1/8"
1/8"
1/4"
1/8"
3/8"
1/2"
1/2"
3/4"
271463
61103
209833
209843
62982
62992
63782
63792
BSP
NPT
NPT
BSP
BSP
BSP
BSP
BSP
NPT
BSP
BSP
BSP
BSP
BSP
BSP
BSP
1/4" BSP
3/8" BSP
1/2" BSP
1" BSP
For full range ask for Air Service
Equipment Catalogue
9092
9092
9092
9092
0062
0007
0015
0020
11
81
31
11
Pressure Gauge
1/8" BSP 0-10 Bar Part No. 9090 1172 00
9
14
31
83

Similar documents

wIrIng products, Inc.

wIrIng products, Inc. and developing cable TV industry. Since then, the industry has grown in many directions and the technology has advanced to levels that allow more video, voice and data to flow through a cable than ...

More information

(Thumpstar) Service Manual

(Thumpstar) Service Manual compensates for the initial wear that occurs during the break-in period Sections 1 and 3 apply to the whole motorcycle. Section 2 illustrates what may be required to perform service described in th...

More information