1” press-down valves

Transcription

1” press-down valves
1” PRESS-DOWN VALVES
1” PRESS-DOWN VALVES
Press-down valves with continuous actuation: the pressure
on the stem causes the opening of the actuating system.
They function both in the upright or upside-down position,
according to the characteristics of the valve housing.
Given their versatility and the characteristics of their
component parts, they can be utilized in most of the
products available on the market.
KPM VALVE
1.1.03
Continuous valves for upright use.
RKRA VALVE
1.1.05
Continuous valves for upright use. A fast filling housing
equipped with an additional gas orifice (VPH) is utilized.
NKPM VALVE
1.1.07
Short stroke continuous valves for upright use.
NRKRA VALVE
1.1.09
Short stroke continuous valves for upright use.
A fast filling housing equipped with an additional
gas orifice (VPH) is utilized.
NKR VALVE
1.1.11
Short stroke continuous valves for upside-down use.
1.1.01
revision: 2
30/04/2013
COSTER
1.1.02
COSTER
revision: 1
31/10/2010
KPM
CONTINUOUS VALVE
HOUSING
The valve is equipped with a standard housing, without additional gas orifice (VPH).
The dip tube is inserted outside the housing tang.
The valve must be used in upright position.
STEM
MOUNTING CUP
STEM Ø 3.9 mm
EXTERNAL GASKET
INTERNAL GASKET
SPRING
HOUSING
Orifice
Orifice
DIP TUBE
STANDARD
FOR POWDERS
STEM ORIFICES
N° orifices
& Ø (mm)
STEM
MATERIAL
Acetalic resin (POM)
OPTIONS
Polyethylene HD (HDPE)
MOUNTING CUP
MATERIAL
PROTECTION
Tin plate
Plain
External gold lacquered / Internal clear lacquered
Clear lacquered
Clear lacquered with PP laminated internal surface
(external gasket not required)
Internal / External PET coated
Micoflex
Clear lacquered
Gold lacquered
Chrome-plate
Aluminium
EXTERNAL GASKET
MATERIAL
Buna
INTERNAL GASKET
MATERIAL
Neoprene
Buna
Chlorobutyl
Butyl
SPRING
MATERIAL
Stainless steel AISI 302
OPTIONS
Soft on request (only for Buna internal gasket)
HOUSING
MATERIAL
Polyethylene HD (HDPE)
OPTIONS
Acetalic resin (POM)
DIP TUBE
MATERIAL
Polyethylene LD (LDPE)
1 x 0.27
1 x 0.30
1 x 0.35
1 x 0.40
1 x 0.50
1 x 0.50
1 x 0.60
1 x 0.60
1 x 0.65
2 x 0.50
2 x 0.50
4 x 0.50
POM
HDPE
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
NOTE
for powders
for powders
•
for powders
•
OPTIONS
Chlorobutyl on request
1.1.03
revision: 5
31/07/2010
COSTER
KPM
STANDARD ACTUATORS
SERIES 1300
SERIES 900
SERIES 500
SERIES 700
SERIES 800
SERIES 1800
SERIES 1300: versions without insert,
with micromist insert, with directional
insert, with tube holding insert and with
special inserts.
Can be supplied mounted on the valve.
SERIES 900 - SLOTTED ACTUATOR:
versions without insert, with micromist
insert, and with directional insert.
Can be supplied mounted on the valve.
SERIES 500: with micromist insert and
with directional insert.
SERIES 700: versions without insert,
with micromist insert, with directional
insert, with tube.
SERIES 800: with micromist insert.
SERIES 1800: with micromist insert
and with directional insert.
SERIES 2100: with micromist insert.
SERIES 2100
V05.453, V05.496, V05.963, V05.992,
V05.967: foaming actuators.
V05.453
V05.496
V05.963
V05.992
V05.967
FILLING DIAGRAMS AND FILLING SPEED GRAPH
13 mm
7 mm
INJECTION PRESSURE IN BARS
FILLING SPEED DURING THE PRODUCTION STAGE: CM3/SEC
60
Maximum pressure for tin plate mounting cups
50
Maximum pressure for aluminium mounting cups
100
40
30
125
1.1.04
COSTER
revision: 5
31/07/2010
150
175
200
225
250
275
The filling speed graph refers to
butane-propane propellant.
It is purely indicative, as it is
based on historical data.
The filling speed depends
on the injection pressure, on the
characteristics of the filling
machine and on the dimensions
of the valve’s components
(shape of the stem, number
and diameter of the orifices on
the stem).
Given the high number
of parameters that can cause
significant variations in the quoted
values, if specific information
is required please ask Coster
commercial offices to obtain
precise data on a specific model.
RKRA
CONTINUOUS VALVE
HOUSING
The valve is equipped with a fast filling housing in which gas orifice (VPH) and product orifice (RTP)
can be of various dimensions. The dip tube is mounted outside the housing tang.
RKRA valves are generally employed for water-based products filled with liquid gas (LPG) or for highly
inflammable products. In this case the orifice dimensions selected according to the gaseous or liquid
phase, guarantee a perfect atomization of particles, thus producing a very fine and uniform spray
that reduces the inflammable properties of the product.
VPH
STEM
RTP
MOUNTING CUP
EXTERNAL GASKET
STEM Ø 3.9 mm
INTERNAL GASKET
SPRING
HOUSING
Orifice
Orifice
DIP TUBE
FOR POWDERS
STANDARD
STEM
MATERIAL
Acetalic resin (POM)
OPTIONS
Polyethylene HD (HDPE)
MOUNTING CUP
MATERIAL
PROTECTION
Tin plate
Plain
External gold lacquered / Internal clear lacquered
Clear lacquered
Clear lacquered with PP laminated internal surface
(external gasket not required)
Internal / External PET coated
Micoflex
Clear lacquered
Gold lacquered
Chrome-plate
Aluminium
EXTERNAL GASKET
MATERIAL
Buna
INTERNAL GASKET
MATERIAL
Neoprene, Buna, Chlorobutyl or Butyl
STEM ORIFICES
OPTIONS
Chlorobutyl on request
SPRING
MATERIAL
Stainless steel AISI 302
DIP TUBE
MATERIAL
Polyethylene LD (LDPE)
HOUSING
MATERIAL
Polyethylene HD (HDPE)
OPTIONS
soft on request (only for buna internal gasket)
N° orifices
& Ø (mm)
1 x 0.27
1 x 0.30
1 x 0.35
1 x 0.40
1 x 0.50
1 x 0.50
1 x 0.60
1 x 0.60
1 x 0.65
2 x 0.50
2 x 0.50
4 x 0.50
POM
HDPE
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
NOTE
for powders
for powders
•
for powders
•
COMBINATION OF HOUSING ORIFICES
GAS ORIFICE
VPH Ø mm 0.00
0.00
0.30
pink
0.40
green
0.50
0.60
blue
0.70
0.80
0.90
1.00
1.20
PRODUCT ORIFICE RTP Ø mm / HOUSING COLOUR
0.30
grey
0.40
sage
red
red
0.50
0.60
0.70
green caramel
green sky-blue
grey orange
pink
brown
0.80
blue
neutral
fuchsia
orange
pink light blue
1.00
yellow
hazel
white
azure
hazel
brown
red
1.20
plum
1.30
1.60
amaranth
green
brown grey
yellow
2.00
sky-blue
beige
brown
blue
green
orange
yellow
green
ivory
black
red
violet
2.50
orange
orchid
pink
turquoise
red
ivory
yellow
1.1.05
revision: 7
30/04/2013
COSTER
RKRA
STANDARD ACTUATORS
SERIES 1300
SERIES 900
SERIES 500
SERIES 700
SERIES 1800
SERIES 2100
SERIES 1300: versions without insert,
with micromist insert, with directional
insert, with tube holding insert and with
special inserts.
Can be supplied mounted on the valve.
SERIES 900 - SLOTTED ACTUATOR:
versions without insert, with micromist
insert, and with directional insert.
Can be supplied mounted on the valve.
SERIES 500: with micromist insert and
with directional insert.
SERIES 700: versions without insert,
with micromist insert, with directional
insert, with tube.
SERIES 800: with micromist insert.
SERIES 1800: with micromist insert.
SERIES 2100: with micromist insert.
SERIES 800
FILLING DIAGRAMS AND FILLING SPEED GRAPH
13 mm
INJECTION PRESSURE IN BARS
FILLING SPEED DURING THE PRODUCTION STAGE: CM3/SEC
50
Maximum pressure
40
30
20
VPH = 0.6 ÷ 1.2
RTP = 0.6 ÷ 1.3
VPH = 0.0 ÷ 0.6
RTP = 0.4 ÷ 0.6
75
100
1.1.06
COSTER
revision: 7
30/04/2013
125
150
VPH > 0.9
RTP = 1.3 ÷ 2.5
175
200
225
The filling speed graph refers to
butane-propane propellant.
It is purely indicative, as it is
based on historical data.
The filling speed depends
on the injection pressure, on the
characteristics of the filling
machine and on the dimensions
of the valve’s components (shape
of the stem, number and
diameter of the orifices on the
stem and on the housing).
Given the high number
of parameters that can cause
significant variations in the quoted
values, if specific information
is required please ask Coster
commercial offices to obtain
precise data on a specific model.
NKPM
SHORT STROKE CONTINUOUS VALVE
HOUSING
The NKPM valve is derived from KPM valve, with reduced stroke and spring.
The valve is equipped with a standard housing, without additional gas orifice (VPH).
The dip tube is inserted outside the housing tang.
The valve must be used in upright position.
STEM
MOUNTING CUP
EXTERNAL GASKET
STEM Ø 3.9 mm
INTERNAL GASKET
SPRING
HOUSING
Orifice
Orifice
DIP TUBE
FOR POWDERS
STANDARD
STEM ORIFICES
STEM
MATERIAL
Acetalic resin (POM)
OPTIONS
Polyethylene HD (HDPE)
MOUNTING CUP
MATERIAL
PROTECTION
Tin plate
Plain
External gold lacquered / Internal clear lacquered
Clear lacquered
Clear lacquered with PP laminated internal surface
(external gasket not required)
Internal / External PET coated
Internal Micoflex / External Gold lacquered
Clear lacquered
Chrome-plate
Aluminium
EXTERNAL GASKET
INTERNAL GASKET
SPRING
MATERIAL
Buna
OPTIONS
Chlorobutyl on request
MATERIAL
Neoprene, Buna,
Chlorobutyl or Butyl
MATERIAL
Stainless steel AISI 302
OPTIONS
Viton on request
HOUSING
MATERIAL
Polyethylene HD (HDPE)
DIP TUBE
MATERIAL
Polyethylene LD (LDPE)
N° orifices
& Ø (mm)
1 x 0.27
1 x 0.30
1 x 0.35
1 x 0.40
1 x 0.50
1 x 0.50
1 x 0.60
1 x 0.60
1 x 0.65
2 x 0.50
2 x 0.50
4 x 0.50
POM
HDPE
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
NOTE
for powders
for powders
•
for powders
•
OPTIONS
Stainless steel AISI 316
1.1.07
revision: 0
30/04/2013
COSTER
NKPM
STANDARD ACTUATORS
SERIES 500
SERIES 700
SERIES 500: with micromist insert
or with directional insert.
SERIES 700: versions without insert,
with micromist insert, with directional
insert, with tube.
SERIES 800: with micromist insert.
SERIES 1800: with micromist insert
or with directional insert.
SERIES 2100: with micromist insert.
SERIES 800
V05.453, V05.496, V05.963, V05.992,
V05.967: foaming actuators.
THIS VALVE IS NOT SUITABLE TO FIT
SERIES 900 SLOTTED ACTUATORS
AND SERIES 1300 ACTUATORS.
SERIES 1800
SERIES 2100
V05.453
V05.496
V05.963
V05.992
V05.967
FILLING METHODS AND FILLING SPEED GRAPH
For these valves the mechanical
opening of the stem is necessary.
(*): Suggested dimension
that must assure mechanical
opening 1.5 ± 0.3.
7.8 mm *
INJECTION PRESSURE IN BARS
FILLING SPEED DURING THE PRODUCTION STAGE: CM3/SEC
60
Maximum pressure for tin plate mounting cups
50
Maximum pressure for aluminium mounting cups
100
40
30
125
1.1.08
COSTER
revision: 0
30/04/2013
150
175
200
225
250
275
The filling speed graph refers to
butane-propane propellant.
It is purely indicative, as it is
based on historical data.
The filling speed depends
on the injection pressure, on the
characteristics of the filling
machine and on the dimensions
of the valve’s components (shape
of the stem, number and
diameter of the orifices).
Given the high number
of parameters that can cause
significant variations in the quoted
values, if specific information
is required please ask Coster
commercial offices to obtain
precise data on a specific model.
NRKRA
SHORT STROKE CONTINUOUS VALVE
HOUSING
The NRKRA valve is derived from RKRA valve, with reduced stroke and spring.
The valve is equipped with a fast filling housing in which gas orifice (VPH) and product orifice
(RTP) can be of various dimensions. The dip tube is mounted outside the housing tang.
NRKRA valves are generally employed for water-based products filled with liquid gas (LPG)
or for highly inflammable products. In this case the orifice dimensio ns selected according
to the gaseous or liquid phase, guarantee a perfect atomization of particles, thus producing
a very fine and uniform spray that reduces the inflammable properties of the product.
VPH
STEM
MOUNTING CUP
RTP
EXTERNAL GASKET
STEM Ø 3.9 mm
INTERNAL GASKET
SPRING
HOUSING
Orifice
Orifice
DIP TUBE
FOR POWDERS
STANDARD
STEM
MATERIAL
Acetalic resin (POM)
OPTIONS
Polyethylene HD (HDPE)
MOUNTING CUP
MATERIAL
PROTECTION
Tin plate
Plain
External gold lacquered / Internal clear lacquered
Clear lacquered
Clear lacquered with PP laminated internal surface
(external gasket not required)
Internal / External PET coated
Internal Micoflex / External Gold lacquered
Clear lacquered
Chrome-plate
Aluminium
EXTERNAL GASKET
MATERIAL
Buna
OPTIONS
Chlorobutyl on request
INTERNAL GASKET
MATERIAL
Neoprene, Buna,
Chlorobutyl or Butyl
MATERIAL
Stainless steel AISI 302
OPTIONS
Viton on request
SPRING
HOUSING
MATERIAL
Polyethylene HD (HDPE)
DIP TUBE
MATERIAL
Polyethylene LD (LDPE)
STEM ORIFICES
N° orifices
& Ø (mm)
1 x 0.27
1 x 0.30
1 x 0.35
1 x 0.40
1 x 0.50
1 x 0.50
1 x 0.60
1 x 0.60
1 x 0.65
2 x 0.50
2 x 0.50
4 x 0.50
OPTIONS
Stainless steel AISI 316
POM
HDPE
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
NOTE
for powders
for powders
•
for powders
•
COMBINATION OF HOUSING ORIFICES
GAS ORIFICE
VPH Ø mm 0.00
0.00
0.30
pink
0.40
green
0.50
0.60
blue
0.70
0.80
0.90
1.00
1.20
PRODUCT ORIFICE RTP Ø mm / HOUSING COLOUR
0.30
grey
0.40
sage
red
red
0.50
0.60
0.70
green caramel
green sky-blue
grey orange
pink
brown
0.80
blue
neutral
fuchsia
orange
pink light blue
1.00
yellow
hazel
white
azure
hazel
brown
red
1.20
plum
1.30
1.60
amaranth
green
brown grey
yellow
2.00
sky-blue
beige
brown
blue
green
orange
yellow
green
ivory
black
red
violet
2.50
orange
orchid
pink
turquoise
red
ivory
yellow
1.1.09
revision: 0
30/04/2013
COSTER
NRKRA
STANDARD ACTUATORS
SERIES 500
SERIES 700
SERIES 500: with micromist insert
or with directional insert.
SERIES 700: versions without insert,
with micromist insert, with directional
insert, with tube.
SERIES 800: with micromist insert.
SERIES 1800: with micromist insert
or with directional insert.
SERIES 2100: with micromist insert.
SERIES 800
THIS VALVE IS NOT SUITABLE TO FIT
SERIES 900 SLOTTED ACTUATORS
AND SERIES 1300 ACTUATORS.
SERIES 2100
SERIES 1800
FILLING METHODS AND FILLING SPEED GRAPH
For these valves the mechanical
opening of the stem is necessary.
(*): Suggested dimension
that must assure mechanical
opening 1.5 ± 0.3.
7.8 mm *
INJECTION PRESSURE IN BARS
FILLING SPEED DURING THE PRODUCTION STAGE: CM3/SEC
50
Maximum pressure
40
30
20
VPH = 0.6 ÷ 1.2
RTP = 0.6 ÷ 1.3
VPH = 0.0 ÷ 0.6
RTP = 0.4 ÷ 0.6
75
100
1.1.10
COSTER
revision: 0
30/04/2013
125
150
VPH > 0.9
RTP = 1.3 ÷ 2.5
175
200
225
The filling speed graph refers to
butane-propane propellant.
It is purely indicative, as it is
based on historical data.
The filling speed depends
on the injection pressure, on the
characteristics of the filling
machine and on the dimensions
of the valve’s components (shape
of the stem, number and
diameter of the orifices on the
stem and on the housing).
Given the high number
of parameters that can cause
significant variations in the quoted
values, if specific information
is required please ask Coster
commercial offices to obtain
precise data on a specific model.
NKR
SHORT STROKE CONTINUOUS VALVE FOR UPSIDE DOWN USE
HOUSING
The NKR valve, with reduced stroke and spring, is equipped with a housing with two side slots,
that permits the complete emptying of the can in the upside-down position.
The valve does not need a dip tube. Nevertheless, the housing is supplied with a tang
where a dip tube can be inserted in order to facilitate the selection of the valves
in the automatic feeding machine.
NKR valves are generally employed for products that must be actuated in upside-down position,
such as hair mousse, cosmetic creams, food products, road markings paints, etc.
STEM Ø 3.9 mm
STEM
MOUNTING CUP
EXTERNAL GASKET
Orifice
INTERNAL GASKET
SPRING
STANDARD
HOUSING
STEM ORIFICES
STEM
MATERIAL
Acetalic resin (POM)
MOUNTING CUP
MATERIAL
PROTECTION
Tin plate
Plain
External gold lacquered / Internal clear lacquered
Clear lacquered
Clear lacquered with PP laminated internal surface
(external gasket not required)
Internal / External PET coated
Internal Micoflex / External Gold lacquered
Clear lacquered
Chrome-plate
Aluminium
OPTIONS
Polyethylene HD (HDPE)
EXTERNAL GASKET
MATERIAL
Buna
OPTIONS
Chlorobutyl on request
INTERNAL GASKET
MATERIAL
Neoprene, Buna,
Chlorobutyl or Butyl
MATERIAL
Stainless steel AISI 302
OPTIONS
Viton on request
SPRING
HOUSING
N° orifices
& Ø (mm)
POM
HDPE
1 x 0.27
1 x 0.30
1 x 0.35
1 x 0.40
1 x 0.50
1 x 0.60
1 x 0.65
2 x 0.50
4 x 0.50
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
NOTE
•
•
OPTIONS
Stainless steel AISI 316
MATERIAL
Polyethylene HD (HDPE)
1.1.11
revision: 0
30/04/2013
COSTER
NKR
STANDARD ACTUATORS
V05.938: actuator for whipped cream.
V05.988: foaming actuator.
V05.990: foaming actuator.
V05.1984: with fan spray, typical
for household products or technical
foam products.
V05.938
V05.988
V05.1984
V05.990
FILLING METHODS AND FILLING SPEED GRAPH
For these valves the mechanical
opening of the stem is necessary.
(*): Suggested dimension
that must assure mechanical
opening 1.5 ± 0.3.
7.8 mm *
INJECTION PRESSURE IN BARS
FILLING SPEED DURING THE PRODUCTION STAGE: CM3/SEC
60
Maximum pressure for tin plate mounting cups
50
Maximum pressure for aluminium mounting cups
100
40
30
125
1.1.12
COSTER
revision: 0
30/04/2013
150
175
200
225
250
275
The filling speed graph refers
to butane-propane propellant.
It is purely indicative, as it is
based on historical data.
The filling speed depends
on the injection pressure, on the
characteristics of the filling
machine and on the dimensions
of the valve’s components
(shape of the stem, number
and diameter of the orifices).
Given the high number
of parameters that can cause
significant variations in the quoted
values, if specific information
is required please ask Coster
commercial offices to obtain
precise data on a specific model.

Similar documents