SP010_QIG_v1 0

SP010 Quick Installation Guide
Document # D2291-100 / Revision 1.0
1
Read Me First
1. The motherboard User’s Manual is available for download from our Web site at http://www.tyan.com. Make
sure to read all precautions and instructions before you start installing the server board.
2. Refer all servicing to qualified personnel to avoid the risk of damage to the server board.
3. Exercise normal ESD (Electrostatic Discharge) procedures during system integration. TYAN/MiTAC
recommends wearing gloves and an anti-static wrist strap to avoid possible damage to the equipment.
4. Current processor socket design places the pins on the motherboard instead of the processor itself. Exercise
extreme caution when installing the processors as the manufacturer’s warranty does not cover damage
inflicted upon the motherboard, including damage to the CPU sockets.
Package Contents
1
Install the Server Board
(Retail Box Only)
Flat-head
Screwdriver
Torx
Screwdriver
2
1
Server Board x 1
Hex
Screwdriver
NOTE: To avoid
damage, do not use
torque force greater
than 7kgf/cm (6.09
lb/n) on each screw.
Install the Processor
Position the mylar onto the base.
Then carefully align those onto
the bottom of the motherboard.
4
Remove the CPU protection cap.
5
Install the processor and make sure
the gold arrow is located in the right
direction.
6
Attach the thermal pad onto the
CPU.
7
Align the heatsink by the guide-pins
and place it onto the top of the
processor.
8
Using an Hex screwdriver, secure the
heatsink with the included screw.
Motherboard
Anti-Static Wrist Strap
REM
OVE
VE
REMO
Rear I/O Shield x 1
Attach the server board to the chassis by securing
the screws on the designated locations.
NOTE: Before
inserting the server
board, you have to
install the base first.
Refer to Step 1~3
on the ”Install the
Processor” section.
Required Tools
Phillips
Screwdriver
2
Insert the server board into the chassis.
72 71 70 69
73
1
68 67 66 65 64
Mylar
d
a bc
A
2
3
63
Base
62
61
60
B
59
4
C
5
6
2
Install the brackets onto the
motherboard.
3
Using a Torx screwdriver, secure
the brackets with the included
screws.
58
57
56
D
54
53
10
52
51
E
11
12
13
14
15
50
F
16
17
23
24 25 26
CONNECTORS
25
ID LED Button (ID_BTN1)
CPLD JTAG Connector (J36)
4-Pin Fan Connectors (SYS_FAN4)
VGA Port /COM1 Port (VGA_COM1)
4-Pin Fan Connectors (SYS_FAN5)
USB3.0 x2 Port (USB1)
RJ45 LAN Port #2 (LAN2)
RJ45 LAN Port #1 (LAN1)
PV_SCM_P_JTAG_ATTENTION_LED
(LED54)
ID LED (ID_LED1)
PCIE#1 12V power indicator (LED5)
BCM5718 (U275)
PEX8718 Port0 LED (LED30)
PCI-E Gen3 Switch PEX8718 (U8)
PEX8718 Port4 LED (LED32)
BMC LED (BMC_LED1)
AST2400 (U1)
PEX8718 Port2 LED (LED33)
PEX8718 Port1 LED (LED31)
PEX8718 Port3 LED (LED34)
Battery Holder (BATTERY1)
BMC JTAG Header (J16)
COM2 Header (COM2)
FAN Header for BB FAN Board
(FAN_FP)
TYAN TPM & Debug Module Header
(DEBUG1)
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
27
28
REM
3
30 32 34 36 37 38 39 40 41
29 31 33 35
BMC SPI FW ROM socket (BMC1)
BIOS Debug Header (BIOS_DEBUG1)
Chassis Intrusion Header (INTRUSION1)
IR VR Chip Flash FW Header (J15)
UCD9090 Program Header (J18)
HOST SMBUS Header (J14)
DS3231 (U284)
BIOS Socket (BIOS1)
TUSB7340IRKMR JTAG Header (J13)
TUSB7340 (U11)
APSS & CY8C3245LT1-163 JTAG Header
(J8)
APSS TMS320F28033PNT (U42)
Front Panel Header (SSI_FP1)
88SE9235 (U14)
PSU ALERT LED (PSU_ALERT1)
PSMI Connector (PSMI1)
SATA4_LED (LED48)
7-pin Vertical SATA3.0 Connector
(SATA3)
7-pin Vertical SATA3.0 Connector
(SATA2)
SATA3_LED (LED47)
7-pin Vertical SATA3.0 Connector
(SATA1)
SATA2_LED (LED46)
7-pin Vertical SATA3.0 Connector
(SATA0)
SLOTS
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
REMOVE
42
22
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
OVE
48 49
47
46
45
44
43
18
19
20
21
1
2
3
4
5
6
7
8
9
REMOVE
55
9
REMOVE
8
REMOVE
REM
OVE
REM
OVE
REMOVE
7
REMOVE
VE
REMO
Motherboard Placement
SATA1_LED (LED45)
ATX 24-pin Power Connector (PW1)
IPMB Pin Header (IPMB1)
SYS_FAN_3 (SYS_FAN3)
CPU0 Socket (CPU0)
CPU0_LED (LED40)
SSI 8-pin CPU0 Power Connector (PW2)
CPU0 FAN (CPU0_FAN)
DIMM2_FAULT_LED (LED42)
DIMM1_FAULT_LED (LED41)
SYS_FAN_2 (SYS_FAN2)
SYS_FAN_1 (SYS_FAN1)
DIMM4_FAULT_LED (LED44)
DIMM3_FAULT_LED (LED43)
Power Button (POWER1)
POWER_ON_LED (LED49)
ROLLUP_FAULT_LED (LED38)
PLANAR_FAULT_LED (LED51)
BOOTING_LED (LED50)
OS_UP_LED (LED39)
Clear CMOS Button (CMOS_CLR)
Reset Button (RESET1)
IBM CPU debug Connector (J2)
Memory Buffer (CENTAUR1)
ID LED Button header (ID_SW1)
Install the Memory
1 Unlock the clips.
4
2 Insert the memory module.
3 Lock the clips.
Install the Power Cable
JUMPERS
A Memory Slots DIMM_D0 (DIMM_D0) D Memory Slots DIMM_A0 (DIMM_A0) a BMC Reset Header (J33)
b COM2 / BMC CONSOLE PORT5 Jumper (BMC_DEBUG1)
B Memory Slots DIMM_C0 (DIMM_C0) E PCI-E 3.0x16 slot(x16link) (PCIE#1)
c COM2 / BMC CONSOLE PORT5 Jumper (BMC_DEBUG2)
C Memory Slots DIMM_B0 (DIMM_B0) F PCI-E 3.0x8 slot(x8link) (PCIE#2)
d BEEP Jumper(MP NI) (J7)
Jumper Cap On/Off
Top View
2
3
2
OVE
Top View
1
3
REMOVE
1
NOTE: Please save and replace the CPU
protection cap when returning the server board
for service.
With jumper installed
on pins 1 and 2
Jumper
Locate the External I/O Ports
REM
Without jumper
DOA/ RMA Reminder
Pins
ID LED Button
COM1
VGA
USB3.0 x2
LAN2
(BCM5718)
LAN1
(BCM5718)