Product Family B58

Transcription

Product Family B58

Level III Service Manual
Product Family B58
Tri-Band Mobile Telephone
Timeport™ 280
GSM 900/1800/1900 MHz & GPRS Technologies
1 and 2
Table of Contents
B58
6881038B15
Table of Contents
Table of Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Product Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Product Names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Product Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Regulatory Agency Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Computer Program Copyrights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
About This Service Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Warranty Service Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
General Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Controls, Indicators, and Input / Output (I/O) Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
User Interface Menu Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Alert Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Battery Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Tools and Test Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Removing and Replacing the Battery Cover and Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Removing and Replacing the SIM Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Removing and Replacing the Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Removing and Replacing the Rear Escutcheon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Removing and Replacing the Rear Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Removing and Replacing the RF Grommet and the Alert Transducer . . . . . . . . . . . . . . . . . . . . . . . . 20
Removing and Replacing the Battery Latch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Removing and Replacing the Battery Cover Latch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Removing and Replacing the RTC Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Removing and Replacing the Transceiver Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Removing and Replacing the Display Module Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Removing and Replacing the Keypad Switch Dome Array . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Removing and Replacing the Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Removing and Replacing the Microphone Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Removing and Replacing the Volume, Voice, and Power Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Removing and Replacing the Infrared Port Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Removing and Replacing the Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Removing and Replacing the Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
SIM Card and Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
SIM Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Manual Test Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Manual Test Mode Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Programming: Software Upgrade and Flexing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
6881038B15
May 14, 2001
i
Table of Contents
P280
Part Number Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Exploded View Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Exploded View Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Model-dependent Part Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Related Publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Index-1
ii
May 14, 2001
6881038B15
B58
6881038B15
Introduction
Introduction
Motorola ® Inc. maintains a worldwide organization that is dedicated to provide
responsive, full-service customer support. Motorola products are serviced by an
international network of company-operated product care centers as well as authorized independent service firms.
Available on a contract basis, Motorola Inc. offers comprehensive maintenance and
installation programs which enable customers to meet requirements for reliable,
continuous communications.
To learn more about the wide range of Motorola service programs, contact your local
Motorola products representative or the nearest Customer Service Manager.
Product Identification
Motorola products are identified by the model number on the housing. Use the entire
model number when inquiring about the product. Numbers are also assigned to
chassis and kits. Use these numbers when requesting information or ordering
replacement parts.
Product Names
Product names included in Product Family B58 (PF B58) telephones are listed on
the front cover. Product names are subject to change without notice. Some product
names, as well as some frequency bands, are available only in certain markets.
Product Changes
When electrical, mechanical or production changes are incorporated into Motorola
products, a revision letter is assigned to the chassis or kit affected, for example; A, -B, or -C, and so on.
The chassis or kit number, complete with revision number is imprinted during
production. The revision letter is an integral part of the chassis or kit number and
is also listed on schematic diagrams and printed circuit board layouts.
Regulatory Agency Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following conditions:
1. This device may not cause any harmful interference, and
2. this device must accept interference received, including interference that may
cause undesired operation.
This class B device also complies with all requirements of the Canadian Interference-Causing Equipment Regulations (ICES-003).
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement
sur le matériel brouilleur du Canada.
6881038B15
May 14, 2001
1
Introduction
6881038B15
B58
1 and 2
P280
Computer Program Copyrights
The Motorola products described in this manual may include Motorola computer
programs stored in semiconductor memories or other media that are copyrighted
with all rights reserved worldwide to Motorola. Laws in the United States and other
countries preserve for Motorola, Inc. certain exclusive rights to the copyrighted
computer programs, including the exclusive right to copy, reproduce, modify,
decompile, disassemble, and reverse-engineer the Motorola computer programs in
any manner or form without Motorola's prior written consent. Furthermore, the
purchase of Motorola products shall not be deemed to grant either directly or by
implication, estoppel, or otherwise, any license or rights under the copyrights,
patents, or patent applications of Motorola, except for a nonexclusive license to use
the Motorola product and the Motorola computer programs with the Motorola
product.
About This Service Manual
Using this service manual and the suggestions contained in it assures proper
installation, operation, and maintenance of PF B58 telephones. Refer questions
about this manual to the nearest Customer Service Manager.
A product family is the group of products having the same Account Product Code
(APC). To locate the APC on a device, refer to “Mechanical Serial Number (MSN)”
later in this manual.
Audience
This document aids service personnel in testing and repairing PF B58 telephones.
Service personnel should be familiar with electronic assembly, testing, and troubleshooting methods, and with the operation and use of associated test equipment.
Use of this document assures proper installation, operation, and maintenance of
Motorola products and equipment. It contains all service information required for
the equipment described and is current as of the printing date.
Scope
The scope of this document is to provide the reader with basic information relating
to PF B58 telephones, and also to provide procedures and processes for repairing
the units at Level 1 and 2 service centers including:
• Unit swap out
• Repairing of mechanical faults
• Basic modular troubleshooting
• Testing and verification of unit functionality
• Initiate warranty claims and send faulty modules to Level 3 or 4 repair
centers.
2
May 14, 2001
6881038B15
Introduction
Conventions
Special characters and typefaces, listed and described below, are used in this
publication to emphasize certain types of information.
➧
G
E
Note: Emphasizes additional information pertinent to the subject
matter.
E
Keys to be pressed are represented graphically. For example, instead of “Press
Caution: Emphasizes information about actions which may result in
equipment damage.
Warning: Emphasizes information about actions which may result
in personal injury.
the Enter Key”, you will see “Press
E”.
Information from a screen is shown in text as similar as possible to what
appears in the display. For example, ALERTS or ALERTS or ALERTS.
Information that you need to type is printed in boldface type
Revisions
Any changes that occur after manuals are printed are described in publication
revision bulletins (PMRs). These bulletins provide change information that can
include new parts listing data, schematic diagrams, and printed board layouts.
Warranty Service Policy
The product will be sold with the standard 12 months warranty terms and conditions. Accidental damage, misuse, and extended warranties offered by retailers are
not supported under warranty. Non warranty repairs are available at agreed fixed
repair prices.
Out of Box Failure Policy
The standard out of box failure criteria applies. Customer units that fail very early
on after the date of sale, are to be returned to Manufacturing for root cause analysis,
to guard against epidemic criteria. Manufacturing to bear the costs of early life
failure.
Product Support
Customer’s original units will be repaired but not refurbished as standard. Appointed Motorola Service Hubs will perform warranty and non-warranty field service for
level 2 (assemblies) and level 3 (limited PCB component). The Motorola HTC centers
will perform level 4 (full component) repairs.
6881038B15
May 14, 2001
3
Introduction
P280
Customer Support
Customer support is available through dedicated Call Centers and in-country help
desks. Product Service training should be arranged through the local Motorola
Support Center.
Ordering Replacement Parts
Only centers authorized to carry out repairs can purchase spare parts. Orders for
spare parts from hubs and Hi-Tech Centers should be placed with the regional
Motorola Parts Distribution Center.
4
May 14, 2001
6881038B15
Specifications
Specifications
General Function
Frequency Range GSM
Frequency Range DCS
Frequency Range PCS
Channel Spacing
Channels
Modulation
Transmitter Phase Accuracy
Duplex Spacing
Frequency Stability
Operating Voltage
Transmit Current
Stand-by Current
Dimensions, with 500 mAh LI Ion batt
Size (Volume)
Weight
Temperature Range
Battery Life, 500 mAh LI Ion Battery
Battery Life, 800 mAh LI Ion Battery
Specification
880-915 MHz Tx (with EGSM)
925-960 MHZ Rx
1710-1785 MHz Tx
1805-1880 MHz Rx
1850.2-1909.8 MHz Tx
1930.2-1989.8 MHz Rx
200 kHz
174 EGSM, 374 DCS, 274 PCS carriers with 8 ch. per carrier
GMSK at BT = 0.3
5 Degrees RMS, 20 Degrees peak
45 MHz GSM, 95 MHz DCS, 80 MHz PCS
± 0.10 ppm of the downlink frequency (Rx)
+3.0V dc to +5.1V dc (battery)
+4.4V dc to +6.5V dc (external connector)
185 - 250 mA average talk current drain
Typically 4.95 mA (DRX2), 3 mA (DXR9)
49 mm x 24 mm x 125 mm (1.9 inches X 0.9 inches X 4.8
inches)
98.5 cc (5.9 in3), with 500 mAh battery
104.5 cc (6.3 in3), with 800 mAh battery
109 gm (3.9 oz), with 500 mAh battery
119 gm (4.2 oz), with 800 mAh battery
-10° C to +55° C (+15° F to +130° F)
Talk Time 120 to 162 minutes
Standby 96 to 158 hours
Talk Time 192 to 259 minutes
Standby 153 to 253 hours
Transmitter Function
RF Power Output
Output Impedance
Spurious Emissions
Specification
33 dBm nominal GSM, 30 dBm nominal DCS / PCS
50 ohms nominal
-36 dBm from 0.1 to 1 GHz, -30 dBm from 1 to 4 GHz
Receiver Function
Receive Sensitivity
RX bit error rate (100k bits) Type II
Channel Hop Time
Time to Camp
Specification
Better than -105 dBm GSM / DCS / PCS
< 2%
500 microseconds
Approximately 5-10 seconds
Speech Coding Function
Speech Coding Type
Specification
Regular pulse excitation / linear predictive coding with long
term prediction (RPE LPC with LTP)
13.0 kbps
20 ms
260 bits
Class 1 bits = 182 bits; Class 2 bits = 78 bits
22.8 kbps
Bit Rate
Frame Duration
Block Length
Classes
Bit Rate with FEC Encoding
6881038B15
May 14, 2001
5
Product Overview
P280
Product Overview
Motorola PF B58 mobile telephones feature global system for mobile communications (GSM) air interface, general packet radio service (GPRS) transport technology,
and wireless application protocol (WAP) Internet browser. The PF B58 incorporates
a new user interface (UI) for easier operation, allows short message service (SMS)
text messaging, and includes personal information manager (PIM) functionality. It
is a tri-band phone that allows roaming within the GSM 900 MHz, digital cellular
system (DCS) 1800 MHz, and personal communications services (PCS) 1900 MHz
bands.
PF B58 telephones support GPRS and SMS in addition to traditional circuit
switched transport technologies. GPRS, where available, provides substantial
increases in mobile data communications performance and the efficient use of radio
spectrum. Data transmission rates for GSM networks can potentially increase from
the current rate of 9.6 kbps up to a theoretical maximum of 171.2 kbps. An increased
data rate is by no means the only benefit provided by GPRS. A key advantage is
the provision of a permanent virtual connection to the network. This “always on”
connection is possible because GPRS uses packet data transfer so that, for example,
email can be downloaded in “background mode.” There is no need for the user to reconnect before requesting a service, eliminating connection set-up delays and
adding convenience and immediacy to data services access. The “virtual” nature of
this connection means that network resources are not consumed during periods
when a user is not actually sending or receiving data.
PF B58 telephones are made of a polycarbonate plastic. The display and speaker,
as well as the keypad, transceiver printed circuit board (PCB), microphone, external
accessory connector, volume buttons, power button, and voice button, are contained
within the flat form-factor housing. There are two types of batteries and battery
doors to provide standard and extended operation. The phone accepts both 3V and
5V mini subscriber identity module (SIM) cards which fit into the SIM holder
underneath the battery. The antenna is a fixed stub type antenna.
Features
The PF B58 telephone uses advanced, self-contained, sealed, custom integrated
circuits to perform the complex functions required for GSM GPRS communication.
Aside from the space and weight advantage, microcircuits enhance basic reliability,
simplify maintenance, and provide a wide variety of operational functions.
Features available in this family of telephones include:
• Lower voltage technology that provides increased standby and talk times
• Extended GSM (EGSM) channels
• Tri-coder/decoder (CODEC) that allows full rate, half rate, and enhanced full
rate modes of transmission
• Supports SMS, concatenated SMS, and cell broadcast messages
• Supports GPRS, circuit switched, and SMS networks
• WAP 1.1 compliant
• 128 X 100 pixel white holographic film graphical display
• Display zoom
• Display animation
• VibraCall® vibrating alert
• Voice recorder personal memo feature
• Voice activation for phone book entries and menu shortcuts
• Simplified text entry using iTAP™ predictive text entry
6
May 14, 2001
6881038B15
Product Overview
•
•
•
•
•
•
•
•
Supports calling name presentation
Supports call forwarding for incoming voice, fax, and data calls
Supports 3V and 5V SIM cards
SIM Toolkit (STK), Class II
USB and RS-232 connectivity
Supports TrueSync® synchronization
Unique joy stick navigation key
Bluetooth™ smart module
Speaker Dependant Voice Recognition and Voice Note Recording
This feature allows voice tags to be used for voice dialing up to 20 phone numbers
in the phone book and for creating up to 5 voice shortcuts for menu items. The phone
must be “trained” by the voice tag being read into the phone’s memory twice before
it is recognized.
Voice tags can be added to the phone’s memory using the usual name addition
methods (i.e., via the phone book menu structure or with the shortcut editor).
➧
The user cannot place or receive calls while adding voice tags to the phone’s memory.
➧
Because the GSM standard does not provide the option to store voice tags onto the
SIM card, voice tags are added to the phone’s memory.
PF B58 telephones also include a voice note recorder that allows up to 2 minutes of
personal messages to be recorded. This feature has a complete set of record,
playback, and management tools that make it easy to store and maintain a list of
personal memos.
Wireless Access Protocol (WAP) 1.1 Compliancy
In the WAP environment, access to the Internet is initiated in wireless markup
language (WML), which is derived from hypertext markup language (HTML). The
request is passed to a WAP gateway which retrieves the information from the server
in standard HTML (subsequently filtered to WML) or directly in WML if available.
The information is then passed to the mobile subscriber via the mobile network.
The PF B58’s microbrowser can be configured for baud, idle timeout, line type,
phone number, and connection type.
➧
Bitmap image data will download as text. If the image is larger than the screen,
only part of the image will display.
➧
If the user receives a call while in browser mode, the browser will pause and allow
the user to resume after completing the call.
Simplified Text Entry
There are three different ways to enter text using the phone keypad:
6881038B15
May 14, 2001
7
Product Overview
P280
• iTAP™ predictive text entry. Press a key to generate a character and a
dynamic dictionary uses this to build and display a set of word or name
options. The iTAP™ feature may not be available on the phone in all languages.
• Tap. Press a key to generate a character.
• Numeric. The keypad produces numeric characters only. For some text areas
this is the only method available; for example, phone numbers.
Caller Line Identification
Upon receipt of a call, the calling party’s phone number is compared to the phone
book. If the number matches a phone book entry, that name will be displayed. If
there is no phone book entry, the incoming phone number will be displayed. In the
event that no caller identification information is available, the message INCOMING
CALL is displayed.
➧
User must subscribe to a caller line identification service through their service
provider.
Call Forwarding
Call forwarding is a network feature that diverts incoming calls to another phone
number if the user or phone is unavailable, or the user does not wish to receive calls.
This option can be used to:
• Divert all incoming voice calls unconditionally
• Divert incoming voice calls whenever the phone is unavailable, busy, not reachable, or not answered
• Divert incoming fax calls
• Divert incoming data calls
• Allow all calls through to the phone.
Detailed operating instructions for these and the other PF B58 features can be found
in the appropriate PF B58 telephone user’s guide listed in the “Related Publications”
section toward the end of this manual.
8
May 14, 2001
6881038B15
General Operation
General Operation
Controls, Indicators, and Input / Output (I/O) Connectors
The PF B58 telephone’s controls are located on the top and side of the device, and
on the keyboard. Indicators, in the form of icons, are displayed on the LCD (see
Figure 2).
InfraRed Data Port (IrDA)
Allows for wireless data transfer
between another wireless phone
or PC's
Power Button & Service Indicator
Press the button to either turn
on or off your phone. The multicolor indicator let's you know
the status of your wireless
service.
Fixed Stub Antenna
High performance in a compact size (27mmL)
Headset Jack
Earpiece
For connection to one of our
optional handsfree headsets,
for those private handsfree
conversations
High quality sound and a comfortable fit
Voice Recognition Key
Allows for handsfree dialing
Volume Keys (up/down)
Select the volume that best
suites the environment you
are in. Even noisy public
Events.
Large Graphical Display (128 x 100 pixels)
Up to six (6) lines of text for those important
messages and WEB browsing
Soft Keys
Keypad
Select from a variety of phone menu
options
Large, well spaced keys for accurate dialing and
feature access. Backlit for ease of use even in
poor lighting conditions
"Joy Stick" Navigation Key
Travel through the phone's menu
with ease and simplicity
Accessory Connector Port
Gives you the ability to enhance the
performance of your phone and expand the
ease of use through a full line of accessories
Figure 1. PF B58 Telephone Controls and Indicators Locations
Menu Navigation
PF B58 telephones are equipped with a new user-friendly interface that employs
soft keys and a 4-way navigation key to access phone functions and features. See
Figure 1.
“Soft keys” refer to non-labeled keys that correspond to text options displayed on
the screen. The left and right soft keys perform the function shown in the corners
of the display. The left key will usually select an option whereas the right key will
usually exit a function or return to a previous screen.
The menu key opens the initial menu structure, or allows access to a submenu
whenever
appears on the screen. See Figure 3 for details of the PF B58 menu
structure.
6881038B15
May 14, 2001
9
General Operation
P280
Liquid Crystal Display (LCD)
The LCD provides a high contrast backlit display for easy readability in all light
conditions. The large bit-mapped 128 x 100 white holographic display includes up
to 6 lines of text.
Display animation makes the phone’s menus move smoothly as the user scrolls up
and down. Turn animation off to conserve the battery.
➧
Whether a phone displays all indicators depends on the programming and services
to which the user subscribes.
Figure 2 shows some common icons displayed on the LCD.
010391o
Figure 2. PF B58 Icon Indicators
• Signal Strength Indicator. Shows the strength of the phone’s connection
with the network. Calls cannot be sent or received when the “no signal” indicator is displayed.
• In Use Indicator. Appears when a call is in progress.
• Roam Indicator. Appears when the phone uses another network system outside the user’s home network. When leaving the home network area, the phone
roams, or seeks, another network.
• Message Waiting Indicator. Appears when the phone receives a text message. This is a network-dependent feature.
• Voice Message Waiting Indicator. Appears when a voicemail message is
received. This is a network-dependent feature.
• Battery Level Indicator. Shows the amount of charge left in the battery. The
more segments visible, the greater the charge. Recharge the battery as soon as
possible when the Low Battery warning message appears.
• Clock. Shows the current time. This is a network-dependent feature.
• Menu Indicator. Indicates the user can press the menu soft key to open a
menu.
• Alert Setting Indicator. Shows the current selected alert. The default alert
setting is a ringer.
10
May 14, 2001
6881038B15
General Operation
User Interface Menu Structure
Figure 3 shows the PF B58 telephone menu structure.
010392o
Figure 3. PF B58 Menu Structure
Alert Settings
PF B58 telephones include up to 32 preset alert tones and vibrations that can be
applied individually to specific alert events or to all events at the same time.
➧
6881038B15
Pressing either volume key will mute the alert.
May 14, 2001
11
General Operation
P280
Battery Function
Battery Gauge
The telephone displays a battery level indicator icon in the idle screen to indicate
the battery charge level. The gauge shows four levels: 100%, 66%, 33%, and Low
Battery.
Battery Removal
Removing the battery causes the device to immediately shut down and any pending
work (for example, partially entered phone book entries or outgoing messages) is
lost.
➧
G
To ensure proper memory retention, turn the phone OFF before removing the
battery. Immediately replace the old battery with a fresh battery.
If the battery is removed while receiving a message, the message will be lost.
Operation
For detailed operating instructions, refer to the appropriate User’s Guide listed in
the Related Publications section toward the end of this manual.
12
May 14, 2001
6881038B15
1 and 2
6881038B15
B58
Tools and Test Equipment
Tools and Test Equipment
The following tables list the tools and test equipment used on the PF B58 telephone.
Use either the listed items or equivalents.
Table 1. General Test Equipment and Tools
Motorola
Part Number1
SPN4726A
Application
Description
Rapid Charger
Used to charge battery and to power device
0180386A82
Antistatic Mat Kit (includes 66-80387A95 antistatic
mat, 66-80334B36 ground cord, and 42-80385A59
wrist band)
Provides protection from damage to device caused
by electrostatic discharge (ESD)
6680388B67
Disassembly tool, plastic with flat and pointed
ends (manual opening tool)
Used during assembly/disassembly of device
RSX4043-A
Torque Driver
Used to remove and replace screws
Torque Driver Bit T-6 Plus, Apex 440-6IP Torx Plus
or equivalent
Used with torque driver
6680388B01
Tweezers, plastic
Used during assembly/disassembly
—
Pliers, long-nose
Used during assembly/disassembly
HP34401A2
Digital Multimeter
Used to measure battery voltage
1. To order in North America, contact Motorola Aftermarket and Accessories Division (AAD) at (847) 538-8000;
Internationally, AAD can be reached by calling (847) 538-8023 or faxing (847) 576-3023.
2. Not available from Motorola. To order, contact Hewlett Packard at (800) 452-4844.
6881038B15
May 14, 2001
13
Disassembly
P280
Disassembly
The procedures in this section provide instructions for the disassembly of a PF B58
telephone. Tools and equipment used for the phone are listed in Table 1, preceding.
G
Many of the integrated devices used in this equipment are vulnerable to damage
from electrostatic discharge (ESD). Ensure adequate static protection is in place
when handling, shipping, and servicing the internal components of this equipment.
G
Avoid stressing the plastic in any way to avoid damage to either the plastic or
internal components.
Removing and Replacing the Battery Cover and Battery
1.
2.
Ensure the phone is turned off.
Depress the battery cover release and slide the battery cover in the direction
of the arrow (see Figure 4A).
A
BATTERY COVER RELEASE
BATTERY COVER
B
010393o
Figure 4. Removing the battery cover
14
May 14, 2001
6881038B15
Disassembly
3.
Lift the battery cover from the phone and remove it completely as shown in
Figure 4B.
A
BATTERY RELEASE
BATTERY
B
010394o
Figure 5. Removing the battery
4.
E
There is a danger of explosion if the Lithium Ion battery is replaced incorrectly.
Replace only with the same type of battery or equivalent as recommended by the
battery manufacturer. Dispose of used batteries according to the manufacturer’s
instructions.
5.
6.
7.
6881038B15
Pull the battery release in the direction shown in Figure 5A, then remove the
battery by lifting its end from the battery compartment and sliding it down
and away from the compartment as shown in Figure 5B.
To replace, align the battery with the battery compartment so the contacts on
the battery match the battery contacts in the phone.
Slide the top of the battery into the receptacle molded into the housing, then
press the bottom end of the battery securely into the battery compartment until
it locks into place.
Line up the battery cover with the rear housing then push it forward until it
snaps firmly in place.
May 14, 2001
15
Disassembly
P280
Removing and Replacing the SIM Card
1.
2.
3.
Remove the battery cover and battery as described in the procedures.
As shown in Figure 6A, slide the SIM holder in the direction of arrow to unlock.
Rotate the SIM holder upward and slide out the SIM card as shown in
Figure 6B.
A
SIM CARD HOLDER
SIM CARD
NOTCHED CORNER
B
SIM CONTACTS
010395o
Figure 6. Removing the SIM card
4.
5.
6.
16
To replace, carefully insert the SIM card into the slot in the holder. Be sure
the SIM is correctly positioned to contact the terminals when closed.
Close the holder and slide to lock in place.
Replace the battery and battery cover as described in the procedures.
May 14, 2001
6881038B15
Disassembly
Removing and Replacing the Antenna
1.
2.
Remove the battery cover and battery as described in the procedures.
Rotate the antenna by hand counterclockwise until loose (See Figure 7).
ANTENNA
010396o
Figure 7. Removing the antenna
3.
G
To prevent damage to antenna or housing, ensure antenna threads are properly
engaged before tightening.
4.
5.
6881038B15
When the antenna threads are completely disengaged, pull the antenna
straight out of the phone housing to remove.
To replace, insert the threaded end of the antenna carefully into the housing
and, after ensuring the threads are properly engaged, tighten firmly by hand.
Replace the battery and battery cover as described in the procedures.
May 14, 2001
17
Disassembly
P280
Removing and Replacing the Rear Escutcheon
DISASSEMBLY TOOL
REAR ESCUTCHEON
REAR HOUSING
.010397o
Figure 8. Removing the rear escutcheon
1.
2.
3.
4.
5.
Remove the battery cover, battery, and antenna as described in the procedures.
Using the flat end of the disassembly tool, carefully pry the escutcheon from
the rear housing to expose the two housing screws located beneath. See
Figure 8.
To replace, remove the protective paper backing from the new escutcheon and
carefully align the escutcheon with the cavity molded into the rear housing.
Press the escutcheon firmly into place making sure pressure is applied evenly
across the entire surface to ensure a tight bond.
Replace the antenna, battery, and battery cover as described in the procedures.
Removing and Replacing the Rear Housing
18
G
This product contains static-sensitive devices. Use anti-static handling procedures
to prevent electrostatic discharge (ESD) and component damage.
G
The housing is fastened with plastic catches. These are delicate and should be parted
using utmost care.
May 14, 2001
6881038B15
Disassembly
1.
2.
Remove the battery cover, battery, SIM card, antenna, and rear escutcheon as
described in the procedures.
Locate the 6 screws holding the front housing to the rear housing. See
Figure 9A.
SCREW
SCREW
SCREW
A
SCREW
SCREW
SCREW
B
HOUSING CATCH, 2 PLACES
REAR HOUSING
C
FRONT HOUSING
TRANSCEIVER
BOARD
ASSEMBLY
010398o
Figure 9. Removing the Rear Housing
3.
6881038B15
Using the Torx driver with a T6 bit, remove the 6 screws and set aside for reuse.
May 14, 2001
19
Disassembly
P280
4.
5.
6.
7.
➧
Using the flat end of the disassembly tool, carefully disengage the catches on
both sides of the housing (see Figure 9B) and separate the rear housing from
the front housing.
Lift the rear housing from the front housing as shown in Figure 9C.
To replace, align the front housing with the rear housing then firmly press
together until the catches engage and the housings are properly assembled.
Replace the 6 screws and tighten firmly. Do not over tighten.
Check the volume, voice, and power buttons to ensure proper operation.
8.
Replace the rear escutcheon, antenna, SIM card, battery, and battery cover as
described in the procedures.
Removing and Replacing the RF Grommet and the Alert Transducer
1.
2.
Remove the battery cover, battery, SIM card, antenna, rear escutcheon, and
rear housing as described in the procedures.
Using the flat end of the disassembly tool, carefully loosen the RF grommet
and pull straight out of the rear housing as shown in Figure 10A.
RF GROMMET
A
REAR HOUSING
DISASSEMBLY TOOL
B
ALERT TRANSDUCER
010399o
Figure 10. Removing the RF grommet and the alert transducer
20
May 14, 2001
6881038B15
Disassembly
3.
4.
G
The alert transducer is fastened to the rear housing with adhesive. Exercise care
when removing to prevent damage to the rear housing.
5.
6.
6881038B15
To replace the RF grommet, press it firmly into place in the rear housing until
completely seated.
To remove the alert transducer, use the flat end of the disassembly tool to
carefully pry the transducer from its cavity in the rear housing. See
Figure 10B.
To replace the alert transducer, remove the protective backing from the new
transducer, then press the transducer into place in the rear housing cavity. Be
sure the transducer is straight and fully seated in the cavity.
Replace the rear housing, rear escutcheon, antenna, SIM card, battery, and
battery cover as described in the procedures.
May 14, 2001
21
Disassembly
P280
Removing and Replacing the Battery Latch
1.
LONG-NOSE PLIERS
BATTERY LATCH SPRING
A
BATTERY LATCH
REAR HOUSING
B
010400o
Figure 11. Removing the battery latch
2.
3.
4.
5.
6.
22
Using long-nose pliers, carefully depress the battery latch spring and remove
from the assembly. Set the spring aside for reuse. See Figure 11A.
With the long-nose pliers, squeeze the 2 battery latch catches inward to release
the battery latch from the housing. Slide the latch downward and lift from the
housing as shown in Figure 11B.
To replace, slide the latch into the housing until it locks into place.
Carefully reinstall the spring and verify proper operation of the latch by
temporarily inserting a battery into the housing.
May 14, 2001
6881038B15
Disassembly
Removing and Replacing the Battery Cover Latch
1.
2.
Using long-nose pliers, carefully squeeze the battery cover latch catches
together to release the battery cover latch from the rear housing. See
Figure 12A.
A
LONG-NOSE PLIERS
REAR HOUSING
BATTERY COVER
LATCH SPRING
BATTERY COVER LATCH
B
010401o
Figure 12. Removing the battery cover latch
3.
4.
5.
6881038B15
Remove the battery cover latch spring from the housing. Set aside for reuse.
To replace, set the battery cover latch spring on its post in the rear housing
then insert the latch into its rear housing cavity until it snaps into place. Verify
proper operation of the latch by temporarily installing a battery cover.
May 14, 2001
23
Disassembly
P280
Removing and Replacing the RTC Battery
1.
2.
G
Use the flat end of the disassembly tool to pry the real time clock (RTC) battery
from its holder on the transceiver board as shown in Figure 13.
Dispose of used batteries according to the manufacturer’s instructions.
DISASSEMBLY TOOL
TRANSCEIVER
BOARD ASSEMBLY
REAL TIME CLOCK (RTC) BATTERY
010402o
Figure 13. Removing the RTC battery
3.
4.
24
To replace, align the new RTC battery with the holder so its positive contact
is facing upward, then snap the battery in place until it is completely seated
in the holder.
May 14, 2001
6881038B15
Disassembly
Removing and Replacing the Transceiver Board
G
1.
2.
Remove the battery cover, battery, antenna, rear escutcheon, and rear housing
as described in the procedures.
Using the flat end of the disassembly tool, carefully loosen the transceiver
board from the front housing.
TRANSCEIVER BOARD ASSEMBLY
FRONT HOUSING
010403o
Figure 14. Removing the transceiver board
3.
4.
➧
Ensure the keypad and the volume, voice, and power buttons are correctly positioned in the front housing relative to the transceiver board. Verify operation of the
buttons after replacing the transceiver board.
5.
6881038B15
Lift the transceiver board from the front housing as shown in Figure 14.
To replace, align the transceiver board with the front housing and gently press
into place.
May 14, 2001
25
Disassembly
P280
Removing and Replacing the Display Module Assembly
G
The flex cable connecting the display module to the transceiver board is easily
damaged. Exercise care when handling.
1.
2.
Remove the battery cover, battery, antenna, rear escutcheon, rear housing, and
transceiver board as described in the procedures.
Locate the 4 display module mounting tabs shown in Figure 15A.
TRANSCEIVER
BOARD
ASSEMBLY
Rear
A
DISPLAYMODULE
DISPLAY MODULE
MOUNTING TAB
(4 PLACES)
Side
B
PLASTIC
TWEEZER
DISASSEMBLY
TOOL
Front
C
LCD FLEX
CONNECTOR
010404o
Figure 15. Removing the display module assembly
26
May 14, 2001
6881038B15
Disassembly
3.
G
Using the flat end of the disassembly tool, gently pry the tabs away from the
transceiver board to release the display module from the transceiver board.
See Figure 15B.
To prevent damage to the display module, do not bend the display module tabs.
4.
5.
6.
7.
8.
While holding the display module slightly away from the transceiver board,
use the flat end of the disassembly tool to gently disconnect the display module
flex connector. See Figure 15C.
Lift the display module away from the transceiver board.
To replace, connect the display module flex connector to the transceiver board.
Align the connectors and press together firmly until completely seated.
Align the display module mounting tabs with the corresponding cut-outs in the
transceiver board, then press together until the display module snaps into
place.
Replace the transceiver board, rear housing, rear escutcheon, antenna, SIM
card, battery, and battery cover as described in the procedures.
Removing and Replacing the Keypad Switch Dome Array
1.
Remove the battery cover, battery, antenna, rear escutcheon, rear housing,
transceiver board, and display module as described in the procedures.
TRANSCEIVER BOARD
KEYPAD SWITCH
DOME ARRAY
DISASSEMBLY TOOL
010405o
Figure 16. Removing the keypad switch dome array
2.
6881038B15
While holding the transceiver board stationary, carefully work the flat end of
the disassembly tool under a corner of the keypad switch dome array as shown
in Figure 16.
May 14, 2001
27
Disassembly
P280
3.
G
Slowly peel the keypad switch dome array from the transceiver board to
remove. Discard the keypad switch dome array just removed.
Do not touch the adhesive on the back of the keypad switch dome array or poor
adhesion and improper operation may result.
4.
5.
To replace, remove the protective backing from a new keypad switch array.
Align the new keypad switch dome array with the transceiver board. Use the
alignment holes to ensure the switch dome array is correctly positioned on the
transceiver board as shown in Figure 17.
ALIGNMENT HOLES
KEYPAD
SWITCH DOME
ARRAY
TRANSCEIVER
BOARD
010406o
Figure 17. Replacing the keypad switch dome array
6.
7.
8.
28
Apply even pressure across the entire surface of the switch dome array to
ensure proper adhesion.
Replace the display module, transceiver board, rear housing, rear escutcheon,
antenna, SIM card, battery, and battery cover as described in the procedures.
Verify correct operation.
May 14, 2001
6881038B15
Disassembly
Removing and Replacing the Keypad
1.
2.
Lift the keypad from the front housing as shown in Figure 18.
FRONT HOUSING
DISASSEMBLY TOOL
KEYPAD
010407o
Figure 18. Removing the keypad
3.
4.
6881038B15
To replace, insert the keypad into the front housing, ensuring the keys align
properly with the openings in the front housing.
Replace the transceiver board, rear housing, rear escutcheon, antenna, battery,
and battery cover as described in the procedures.
May 14, 2001
29
Disassembly
P280
Removing and Replacing the Microphone Assembly
G
1.
transceiver board, and keypad as described in the procedures.
FRONT HOUSING
DISASSEMBLY TOOL
MICROPHONE ASSEMBLY
010408o
Figure 19. Removing the microphone assembly
2.
3.
➧
The microphone assembly uses conductive elastomer to make contact with the
transceiver board pads.
4.
30
Using the flat end of the disassembly tool, carefully pry the microphone
assembly from its cavity in the front housing as shown in Figure 19. The
microphone assembly should come out of its cavity easily.
To replace, align the microphone assembly with the microphone cavity. Be sure
the open end of the microphone is facing the front housing. Press the microphone assembly firmly into place, ensuring it is straight and completely seated
in its cavity.
Replace the keypad, transceiver board, rear housing, rear escutcheon, antenna,
battery, and battery cover as described in the procedures.
May 14, 2001
6881038B15
Disassembly
Removing and Replacing the Volume, Voice, and Power Buttons
1.
2.
Lift the volume buttons, the power button, and the voice button from the front
housing. The plastic tweezer may be useful when removing the buttons. See
Figure 20.
PLASTIC TWEEZER
VOLUME BUTTONS
POWER BUTTON
VOICE BUTTON
FRONT HOUSING
010409o
Figure 20. Removing the volume, voice, and power buttons
3.
4.
6881038B15
To replace, insert the buttons into their respective front housing cavities,
ensuring each button is properly aligned and seated within the housing.
May 14, 2001
31
Disassembly
P280
Removing and Replacing the Infrared Port Lens
1.
2.
Using the flat end of the disassembly tool, gently pry the infrared (IR) port lens
from its cavity in the front housing as shown in Figure 21. The IR port lens
should come away from the housing easily.
INFRARED
PORT LENS
FRONT HOUSING
DISASSEMBLY TOOL
010410o
Figure 21. Removing the infrared port lens
3.
4.
To replace, insert the IR port lens into its front housing cavity. Be sure the lens
is properly aligned and fully seated within the front housing.
Removing and Replacing the Speaker
1.
transceiver board, and IR port lens as described in the procedures.
SPEAKER
FRONT HOUSING
DISASSEMBLY TOOL
010411o
Figure 22. Removing the speaker
32
May 14, 2001
6881038B15
Disassembly
2.
G
Using the flat end of the disassembly tool, pry the speaker from its cavity in
the front housing.
The speaker is fastened to the front housing with adhesive. Exercise care when
removing to prevent damage to the front housing.
3.
4.
To replace the speaker, remove the protective backing from the new speaker,
then press the speaker into place in the front housing cavity. Be sure the
speaker is straight and fully seated within the cavity.
Replace the IR port lens, transceiver board, rear housing, rear escutcheon,
antenna, battery, and battery cover as described in the procedures.
Removing and Replacing the Lens
1.
transceiver board, keypad, microphone, volume buttons, voice button, power
button, IR port lens, and speaker as described in the procedures.
CATCH
A
FRONT HOUSING
LENS
DISASSEMBLY TOOL
B
010412o
Figure 23. Removing the lens
6881038B15
May 14, 2001
33
Disassembly
P280
2.
G
The lens is fastened to the front housing with adhesive. Exercise care when removing
to prevent damage to the front housing.
3.
4.
G
While holding the catches in the disengaged position, use the flat end of the
disassembly tool to pry the lens from the front housing as shown in Figure 23B.
Rotate the lens upward and lift from the housing.
Do not remove the transparent protective film from the front of the new lens. This
film prevents damage to the lens during service and handling. It is to be removed
only by the end user.
5.
6.
7.
8.
9.
34
Disengage the lens catches by pushing toward the bottom of the housing as
shown in Figure 23A.
To replace, remove the protective backing from the adhesive on back of the new
lens. Be careful not to touch the adhesive.
Insert the lens’ 2 bottom catches into the mating slots in the front housing.
Carefully align the lens with the front housing and rotate the lens downward
to engage the lens top catches.
Apply even pressure across the adhesive area of the lens to bond it to the
housing. Ensure the lens is straight and flush with the front housing.
Replace the speaker, IR port lens, voice button, power button, volume buttons,
microphone, keypad, transceiver board, rear housing, rear escutcheon, antenna, battery, and battery cover as described in the procedures.
May 14, 2001
6881038B15
SIM Card and Identification
SIM Card
A SIM (Subscriber Identity Module) card is required to access the existing local
GSM network, or remote networks when traveling (if a roaming agreement has been
made with the provider).
The SIM card contains:
• All the data necessary to access GSM services
• The ability to store user information such as phone numbers.
• All information required by the network provider to provide access to the network.
Identification
Each Motorola GSM device is labelled with a variety of identifying numbers. The
following information describes the current identifying labels.
Mechanical Serial Number (MSN)
The Mechanical Serial Number (MSN) is an individual unit identity number and
remains with the unit throughout the life of the unit.
The MSN can be used to log and track a unit on Motorola's Service Center Database.
The MSN is divided into 4 sections as shown in Figure 24.
MSN 10 Digits
3 Digits
APC
Account Product Code
TM
i.e. StarTAC Phone130
1 Digit
DC
Distribution Center
i.e. Easter Inch
2 Digits
4 Digits
DC
SNR
Date Code: Year and
Month of Shipment
Unit's individual serial
number
000807-A
Figure 24. MSN Label Breakdown
6881038B15
May 14, 2001
35
P280
International Mobile Station Equipment Identity (IMEI)
The International Mobile station Equipment Identity (IMEI) number is an individual number unique to the PCB and is stored within the unit's memory. The following
diagram illustrates the various parts of this number.
IMEI 16 Digits
Type Approval Code
6 Digits
2 Digits
6 Digits
2 Digits
TAC
FAC
SNR
IU
Distribution Center
factory code
Individual PCB Serial
Number
Internal Use - spare
digits
000808-O
Figure 25. IMEI Label Breakdown
Other label number configurations present are:
• TRANSCEIVER NUMBER: Identifies the product type. Normally the SWF
number. (i.e. V100).
• PACKAGE NUMBER: Identifies the equipment type, mode, and language in
which the product is shipped.
36
May 14, 2001
6881038B15
Troubleshooting
Troubleshooting
Manual Test Mode
Motorola PF B58 telephones are equipped with a manual test mode capability. This
allows service personnel to verify functionality and perform fault isolation by
entering keypad commands.
To enter the manual test command mode, a GSM / DCS test SIM must be used.
1. Press , to turn the phone OFF.
2. Remove the battery as described in the procedures.
3. Remove the customer’s SIM card from the phone as described in the procedures.
4. Insert the test SIM into the SIM slot.
5. Replace the battery as described in the procedures.
6. Press , to turn the phone ON.
Manual Test Mode Commands
Table 2. Manual Test Commands
Key Sequence
Test Function/Name
Remarks
<Menu>048263* Enter manual test mode
“End” Key
54*
Exit manual test mode
Suspend
0*0*0
Select tone 0
0*0*1
Select tone 1
0*0*2
Select tone 2
0*0*3
Select tone 3
0*0*4
Select tone 4
0*0*5
Select tone 5
0*0*6
Select tone 6
0*0*7
Select tone 7
0*0*8
Select tone 8
0*0*9
Select tone 9
0*1*X
Disable tone X
3*0*1
Enable vibrator
3*0*0
Disable vibrator
5*0*0
Set audio level 0
5*0*1
Set audio level 1
5*0*2
Set audio level 2
5*0*3
Set audio level 3
5*0*4
Set audio level 4
5*0*5
Set audio level 5
5*0*6
Set audio level 6
5*0*7
Set audio level 7
6881038B15
Required for all Test Mode Operations
May 14, 2001
37
Troubleshooting
P280
Table 2. Manual Test Commands (Continued)
Key Sequence
Test Function/Name
5*0*8
Set audio level 8
5*0*9
Set audio level 9
5*0*10
Set audio level 10
5*0*11
Set audio level 11
5*0*12
Set audio level 12
5*0*13
Set audio level 13
5*0*14
Set audio level 14
5*0*15
Set audio level 15
Remarks
6*2*2*0*0
Set Audio Path. Int Mic, IntSpk, RX unmute, TX unmute
6*4*6*0*0
Set Audio Path. Boom Mic, Boom Spk, RX unmute, TX unmute
10*0*3
Set band GSM 900
10*0*4
Set band DCS 1800
10*0*5
Set band PCS 1900
10*0*6
Set dual band GSM 900 / 1800
10*1*0
Read band
18*0
18*1
Initialize Non-volatile memory (Master Clear)
55*2*001
Test Display. All pixels ON
55*2*000
Test Display. All pixels OFF
55*2*002
Test Display. Checkerboard pattern A
55*2*003
Test Display. Checkerboard pattern B
55*2*004
Test Display. Border pixels ON
*#06#
3= GSM 4= DCS 5= PCS 6 =GSM/DCS
Initialize non-volatile memory (Master Reset)
IMEI Check
No Test Mode Required
Phone Set up --> Flex Version / Technology / S-W Version / Readiness Status
Phone Status -->
Other
Information
38
May 14, 2001
No Test Mode Required
6881038B15
Troubleshooting
Troubleshooting Chart
Table 3. PF B58 Telephone: Level 1 and 2 Troubleshooting Chart
SYMPTOM
1. Telephone will not turn on or stay on.
2. Telephone exhibits poor reception or
erratic operation such as calls frequently
dropping or weak or distorted audio.
3. Display is erratic, or provides partial or
no display.
PROBABLE CAUSE
VERIFICATION AND REMEDY
a) Battery either discharged or
defective.
Measure battery voltage across a 50 ohm (>1
Watt) load. If the battery voltage is <3.25 Vdc,
recharge the battery using the appropriate
battery charger. If the battery will not recharge,
replace the battery. If battery is not at fault,
proceed to b.
b) Battery connectors open or
misaligned.
Visually inspect the battery connectors on both
the battery and the telephone. Realign and, if
necessary, either replace the battery or refer to
a Level 3 Service Center for the battery
connector replacement. If battery connectors
are not at fault, proceed to c.
c) Transceiver board assembly
defective.
Remove the transceiver board assembly.
Substitute a known good assembly and
temporarily reassemble the unit. Depress the
PWR button; if unit turns on and stays on,
disconnect the dc power source and reassemble
the telephone with the new transceiver board
assembly. Verify that the fault has been cleared.
a) Antenna assembly defective.
Check to make sure that the antenna pin is
properly connected to the transceiver board
assembly. If connected properly, substitute a
known good antenna. If the fault is still present,
proceed to b.
b) Transceiver board assembly
defective.
Replace the transceiver board assembly (refer
to 1c). Verify that the fault has been cleared and
reassemble the unit with the new transceiver
board assembly.
a) Mating connections to or from
transceiver board faulty.
Remove rear housing from unit, check general
condition of flex connector if the flex connector is
good, check that the connector is fully pressed
down. If faulty connector, replace the transceiver
board assembly. If connector is not at fault,
proceed to b.
defective.
board assembly.
4. Incoming call alert transducer audio
distorted or volume is too low.
a) Faulty transceiver board assembly. Replace the transceiver board assembly (refer
board assembly.
5. Telephone transmit audio is weak.
(usually indicated by called parties
complaining of difficulty in hearing voice).
a) Microphone connections to the
Gain access to the microphone as described in
transceiver board assembly defective. the procedures. Check connections. If connector
is faulty proceed to c; if the connector is not at
fault, proceed to b.
b) Microphone defective.
6881038B15
May 14, 2001
Gain access to microphone. Disconnect and
substitute a known good microphone. Place a
call and verify improvement in transmit signal as
heard by called party. If good, reassemble with
new microphone. If microphone is not at fault,
reinstall original microphone and proceed to c.
39
Troubleshooting
P280
Table 3. PF B58 Telephone: Level 1 and 2 Troubleshooting Chart (Continued)
SYMPTOM
PROBABLE CAUSE
c) Transceiver board assembly
defective.
VERIFICATION AND REMEDY
board assembly.
6. Receive audio from earpiece speaker is a) Connections to or from transceiver Gain access to the transceiver board assembly
weak or distorted.
board assembly defective.
as described in the procedures. Check
connection from the earpiece to the transceiver
board assembly. If connection is not at fault,
proceed to b.
b) Earpiece speaker defective.
Remove the transceiver board and insert into
known good speaker. Ensure good connection.
Place a call and verify improvement in earpiece
audio. If fault is cleared, reassemble the phone
with the good speaker. If fault is not cleared,
proceed to c.
c) Antenna assembly defective.
Check to make sure the antenna is installed
correctly. If the antenna is installed correctly,
substitute a known good antenna assembly. If
this does not clear the fault, reinstall the original
antenna assembly and proceed to d.
d) Transceiver board assembly
defective.
reassemble with the new transceiver board
assembly.
a) SIM card defective.
Check the SIM card contacts for dirt. Clean if
necessary, and check if fault has been cleared.
If the contacts are clean, insert a known good
SIM card into the telephone. Power up the unit
and confirm that the card has been accepted. If
the fault no longer exists, replace the defective
SIM card. If the SIM card is not at fault, proceed
to b.
defective.
board assembly.
8. Vibrator feature not functioning.
a) Transceiver board assembly
defective.
board assembly.
9. Internal Charger not working.
a) Faulty charger circuit on transceiver Test a selection of batteries in the rear pocket of
board assembly.
the desktop charger. Check LED display for the
charging indications. If these are charging
properly, then the internal charger is at fault.
board assembly.
10. Real Time Clock resetting when
standard battery is removed.
a) RTC battery in the transceiver
board.
7. Telephone will not recognize or accept
SIM card.
11. No or weak audio when using headset. a) Headset not fully pushed home.
b) Faulty jack socket on transceiver
board assembly.
40
May 14, 2001
Replace RTC battery according to the
procedures.
Ensure the headset plug is fully seated in the
jack socket.
board assembly.
6881038B15
Troubleshooting
Programming: Software Upgrade and Flexing
Contact your local technical support engineer for information about equipment and
procedures for flashing and flexing.
6881038B15
May 14, 2001
41
Part Number Charts
P280
Part Number Charts
The following charts are provided as a reference for the parts associated with PF
B58 telephones.
Exploded View Diagram
2
1
3
4
5
6
7
8
9
12
10
11
14
24
23
13
15
22
21
16
20
17
19
14
14
18
010249-O
Figure 26. Exploded View Diagram
42
May 14, 2001
6881038B15
Part Number Charts
Exploded View Parts List
Table 4. Exploded View Parts List
Item
Number
Motorola Part
Number
Item
Number
Motorola Part
Number
1
6188612K03
Lens
18
See Table 5
Battery Door, Painted
2
3
3589002K01
Speaker Felt
19
See Table 5
Rear Housing, Painted
See Table 5
Front Housing, Painted
20
1587622L02
Battery Latch
4
3888884K02
Power Button
21
4088922K01
Switch Dome Metal Array
5
5087975K02
Speaker 15Dx2.7 Tall w/ Pads
22
3888550L
6
6188925K01
Lens, IRDA
23
3288588K01
Dust Gasket
7
3888923K01
Volume Button
24
5085600J01
Microphone
8
3888924K01
Voice Activation Button
25
9
7289437K04
Display Module Assembly
26
10
See Note 1
11
5089001K01
Description
Transceiver Board Assembly
27
Alert
28
12
8586336P01
Antenna, Jade
29
13
4109494U03
Spring, Battery Door Button
30
14
0309315B07
Screw, Torx 6, 1.8 (6)
31
15
1588617K02
Panther 2 Battery Door Button
32
16
See Table 5
Rear Escutcheon
33
17
See Table 6
Battery
34
Notes:
Description
Keypad
1. Not available as spares in EMEA Service markets.
E
6881038B15
There is a danger of explosion if the Lithium Ion battery pack is replaced incorrectly.
Replace only with the same type of battery or equivalent as recommended by the
battery manufacturer. Dispose of used batteries according to the manufacturer’s
instructions.
May 14, 2001
43
Part Number Charts
P280
Model-dependent Part Numbers
Table 5. Model-dependent Part Numbers
Item
Number
44
Part Description
Part Number
3
Front Housing, painted, Matte Silver
1588113L10
3
Front Housing, Painted, Marine Silver
1588113L10
3
Front Housing, Painted, Smoked Silver
1588113L12
3
Front Housing, Painted, Graphite
1588113L19
16
Rear Escutcheon, Black w/ White Text, 280
1388836K03
16
Rear Escutcheon, Black w/ White Text, Timeport
1388836K04
18
Battery Door, Painted, Matte Silver, 800mAh
1588098L02
18
Battery Door, Painted, Marine Silver, 800mAh
1588098L03
18
Battery Door, Painted, Smoked Silver, 800mAh
1588098L04
18
Battery Door, Painted, Graphite, 800mAh
1588098L09
18
Battery Door, Painted, Matte Silver, 500mAh
1588097L02
18
Battery Door, Painted, Marine Silver, 500mAh
1588097L03
18
Battery Door, Painted, Smoked Silver, 500mAh
1588097L04
18
Battery Door, Painted, Graphite, 500mAh
1588097L09
19
Rear Housing, Painted, Matte Silver
1588144L10
19
Rear Housing, Painted, Marine Silver
1588144L11
19
Rear Housing, Painted, Smoked Silver
1588144L12
19
Rear Housing, Painted, Graphite
1588144L19
May 14, 2001
6881038B15
Part Number Charts
Accessories
Table 6. Accessories
Part Description
Part Number
Battery, Slim, Lithium Polymer, 500 mAh
SNN5717
Battery, Lithium Polymer, 800 mAh
SNN5705
Travel Charger, Rapid, Universal, US Flip
SPN4716
Travel Charger, Rapid, Universal, Argentina
SPN4735
Travel Charger, Rapid, Universal, China
SPN4743
Travel Charger, Rapid, Universal, Hong Kong
SPN4737
Travel Charger, Rapid, Universal, Korea
SPN4736
Travel Charger, Rapid, Universal, Brazil
SPN4738
Adapter, Euro Plug
SPN4940
Adapter, UK Plug
SPN4739
Adapter, Aus / NZ Plug
SPN4741
Adapter, India Plug
SPN4744
Adapter, Korea Plug
SPN4756
Dual-Pocket Desktop Charger Base - English Label
SPN4772
Dual-Pocket Desktop Charger Base - Chinese Label
SPN4773
Vehicle Power Adapter
SYN7818
Easy-Install Hands Free Car Kit (analog audio)
SYN8597
Headset (Jewel Case)
SYN7453
Headset with Boom Microphone
SYN8146
Bluetooth Clip In Module
SYN8640
Bluetooth PCMCIA Card
SYN8625
USB Cable
SKN2101
RS-232 Data Cable (Head only)
SYN0279
RS-232 Data Cable (Cable only)
SKN2102
Related Publications
Motorola Timeport 280 Wireless Phone User Guide, English
9888873L01
Motorola Timeport 280 Wireless Phone Reference Guide, English
6809435A65
6881038B15
May 14, 2001
45
Part Number Charts
46
P280
May 14, 2001
6881038B15
1 and 2
Index
B58
6881038B15
Index
Index
I
identification 35
international mobile station equipment identity 36
mechanical serial number 35
product 1
IMEI 36
Introduction 1
A
accessories
part numbers 45
alert modes 11
antenna, removing and replacing 17
K
B
keypad keys, removing and replacing 29, 32, 33
keypad PCB, removing and replacing 27, 31
battery
function 12
gauge 12
removing 14
battery door
removing 14
L
LCD 10
liquid crystal display (LCD) 10
M
C
caller ID 8
Canadian Interference-Causing Equipment regulations 1
changes
product 1
closed user group 7
commands, manual test mode 37
controls 9
conventions 3
copyrights
computer software 2
manual test mode 37
microphone, removing and replacing 30
MSN 35
N
names
product 1
O
overview 6
D
disassembly 14
display animation 8
E
exploded view diagram 42
exploded view parts list 43
F
FCC rules 1
features 6
call diverting 8
caller ID 8
text entry 7
voice recognition 7
Wireless Access Protocol (WAP) 7
6881038B15
P
part numbers
accessories 45
parts 42
exploded view diagram 42
exploded view parts list 43
product
changes 1
identification 1
names 1
publications, related 45
R
rear housing
removing 18
regulatory agency compliance 1
related publications 45
removing
May 14, 2001
Index-1
Index
antenna 17
battery 12, 14
battery door 14
keypad keys 29, 32, 33
keypad PCB 27, 31
microphone 30
rear housing 18
SIM card 16
transceiver board 20, 25
replacement parts
ordering 4
replacing
antenna 17
keypad keys 29, 32, 33
keypad PCB 27, 31
microphone 30
revisions
service manual 3
P280
V
voice recognition 7
W
WAP (Wireless Access Protocol) 7
warranty service 3
Wireless Access Protocol (WAP) 7
S
serial number
mechanical 35
service manual
about 2
revisions 3
scope 2
service policy 3
customer support 4
out of box failure 3
product support 3
replacement parts 4
shut down
upon battery removal 12
SIM card 35
removing 16
replacing 16
support
customer 4
product 3
T
test equipment 13
text entry 7
tools 13
transceiver board
removing 20, 25
troubleshooting 37
manual test mode 37
manual test mode commands 37
Index-2
May 14, 2001
6881038B15
P280 - RF SCHEMATICS
B
A
C
D
E
F
G
H
RECEIVER FRONT END
1
I
J
K
L
M
RF_V2
RF_V2
FL100
RF_V2
ANTENNA SWITCH
N_GSM_EXC_SW TX1
J100
EXT_TEST CONN
2
GSM_EXC_SW
TX2
DCS_SW
RX1
N_DCS_SW
RX2
DCS_SEL DCS_SEL
RF_V2
Q151
A10
Q203
U402
FL104
400MHz
DCS_SW
RX_EN
N_DCS_SEL
RX_EN N_GSM_SEL
Q202
N_TX_EN
RF_V2 N_DCS_SEL
PAC_275
RF_V2
N_EXC_EN
Q202
N_GSM_SEL
N_DCS_SW
GSM_EXC_EN
RX_EN
FL101
1805-1880MHz
EXC_EN
EXC_EN
U110
RF_V2
GSM_EXC_SW
Q202
U110
U100
Frontend IC
FL102
1930-1990MHz
RF_V2
U10
3
5V
Q204
Q351
N_RVCO
RF_V2
N_DCS_SEL
FL103
925-960MHz
PAC_275
RVCO
N_TXVCO
N_GSM_EXC_EN
U120
N_GSM_EXC_SW
EXC_EN
N_GSM_SEL
5V
U120
RF_V2
RF_V2
RVCO
PRE_IN
4
SW_VCC
RF_V2
RVCO
GP04
Q200
PA_B+
TP202
GP05
TRANSMITTER
PA_B+
TP201
BFSR
CR200
BCLKR
N_RVCO
CR201
DM_CS
RF_V1
Q451
U500
GSM IPA
GPRS TriBand T280 (Panther2) 8488516k01_P13.5
RX Local Osc.
RX_ACQ
B+
RF_V2
SF_OUT
5
13MHz Osc.
BDR
Q450
U300
RX VCO
5V
N_GSM_SEL
DCS_SEL
1342MHz; 1442MHz; 1560MHz
RF_V1
5V
RF_V2
6
MAGIC_13MHz
BCLKX
GSM_EXC_EN
N_DCS_SEL
SF_OUT
CLK_SELECT
U201
MAGIC DM
N_GSM_SEL
TX_KEY
DM_CS
MAGIC_SPI_CS
RF_SPI_CLK
RF_MOSI
BDX
RF_V2
RF_V1
N_TXVCO
7
PA_B+
PA_B+
RF_V2
Q201
CPRX
N_GSM_EXC_EN
U550
DCS/PCS IPA
RF_V2
Vref
CP_TX
V1_FILT
8
B+
U1905
SF_OUT
U350
TX VCO
Q530
GSM DCS PCS
CR545
N_GSM_SEL
0
1
1
N_DCS_SEL
1
0
1
1 BUFFER
ENABLE
0
N_GSM_EXC_EN
0
1
GSM_EXC_EN
1
0
VCO
BAND
5V
Y200
26MHz
GSM_EXC_EN
9
U400
PAC IC
PAC_275
Q410
N_GSM_EXC_EN
N_GSM_EXC_EN
VCTRL
SAT_DET
PAC_275
DET_SW
10
TX_KEY_OUT
AOC_DRIVE
RX SIGNAL PATH
11
TEXT
TX SIGNAL PATH
MAIN VCO SIGNAL PATH
TUNING VOLTAGES
13 MHz REFERENCE CLOCK
DATA BUS
ADDRESS BUS
REFERENCE SIGNALS
N
P280 - AL SCHEMATICS
V3
V2
J903
SMART CARD CONN
V2
DVDD
V2
UCTS2_UF
SR_CS
URXD2_SIM_RX1
UCTS2_SIM_RST1
VSIM_EN1
INT3
SPICS7
URTS2_SIM_CLK1
SCKA_UF
INT3_UF
STDA_UF
SPICS6
SPICS7_UF
VR943
EB1_N
EB0_N
V2
V3
OE_N
RW_N
U701
MCU_DE
TMS
IVDD
V3
JVDD
OVCC
CVDD
BVDD
MOD
SIM_TX1
GCAP_13MHz
RESET_OUT
U703
EB1_N
J901
CE BUS
SW_B+
S500
SWITCH
KBC0
KBC0
WDOG
RESET
DATALOG_N
CE2
PWR_SW
MAGIC_13MHz
IRDA_TX
B+
V2
HS_INT
GCAP_CLK
Q600
TCK
TDI
RESET
OC3
V3
DSP_DE
TRST
TDO
BRST_CLK
FLASH_CS
OE_N
EB1_N
ADV_N
RESET_OUT
ECB_N
SIM_PD1
UTXD2
V2
V1
CLK_SELECT
STBY
U902
SC2A_UF
SPICS8
CR700
U702
EVDD
VSIM_EN1_UF
HVDD
SIM_PD1_UF
SW_B+2_EN
DATA(15:0)
V3
V3
AVDD
URTS2_UF
Q900
V3
URXD2_UF
UTXD2_UF
B+
JTAG
SR_VCC
USB_VP
IRDA_RX
KBR1
KBR1
IRDA_EN
USB_TXENB
USB_EOP
INT3
URTS_USBXRXD
GCAP_INT
EB0_N
OE_N
RW_N
KBR0
U700
PATRIOT
KBR0
SW_B+_EN
BATT_FDBK
KBR7
EXT_BATT
CE5
CE3
USB+_UTXD
USB_UXRD
USB_PWR
ADDRESS(23:0)
UCTS
SW_B+2_EN
SPICS7
GCAP_SPI_CS
DISP_SPI_CS
BB_MOSI
ECB_N
USB_PWR
BB_SPI_CLK
EB0_N
EB1_N
OE_N
BATT_FDBK
UCDC
SPICS8
CE2
CE1
FLASH_CS
ADV_N
BRST_CLK
SW_B+
RW_N
CE4
SPICS6
KBR6
MAGIC_SPI_CS
RF_MOSI
RF_SPI_CLK
KBR5
KBR5
U904
SIM BLOCK
VSIM1
B+
USB+
U904
LS_SIM_RST
CHRG_C
B+
USBUSB_VP
USB_EOP
UTXD_VDOUT
URTS_USBXRXD
URXD_USBVM
USB_TXENB
HS_SPKR
ON_OFF
CR903
RESET
URTS2_SIM_CLK1
PWR_SW
GCAP_INT
EXT_B+
GCAP_CLK
SR_CS
CE1
SR_VCC
V3
KBR5
KBC1
N_TX_EN
KBC0
KBR7
SW_B+_EN
RX_EN
BATT_SER_D
RX_ACQ
DM_CS
TX_KEY
MIDRATE_2
MIDRATE_1
BFSR
BCLKR
BCLKX
BDR
BDX
N_EXC_EN
DISP_SPI_CS
IVDD
CR950
BL_SNK
ALRT_VCC
BATT_FDBK
V2
U1909
ALRT_VCC
V2
CR500
DATALOG_N
STBY
RTC BATT
M810
Motor
WDOG
WDI
V_BOOST
32,768kHz
V3
V1
THERM_BIAS
RESET_OUT
BB_SPI_CLK
SIM_RST
Y900
SIM_TX1
URXD2_SIM_RX1
UCTS2_SIM_RST1
URTS2_SIM_CLK1
VSIM_EN1
SIM_PD1
SIM_TX
VSIM_EN
SIM_RST
SIM_RX
EXT_BATT
V2
CR850
U900
GCAP3
SDI_D_C
Q944
J912
BATTERY CONN
SIM_CLK
5V
BB_MOSI
BATT+
TX_KEY
SIM_TX
SIM_RX
J700
DISPLAY CONN
EXT_BATT
BL_SNK
LED_RED
LED_GRN
LS_SIM_CLK
VR940
EXT_B+
SIM_TX
SIM_IO
MIDRATE CHARGER
EXT_B+
Q945
V2
KBR5
KBC0
KBC1
CR940
MAIN
B+
B+
BATT+ Q942
KBR7
Q932
BATT+
BATT_FDBK
B+
SIM_CLK
UTXD_VDOUT
CR902
VREF
V3
ALRT_VCC
PA_DRV
OC3
BATT+
CR932
EXT_B+
SIM_PD0
VR948
MIDRATE_1
USB_33
V2
V_BUCK
USB_PWR
USB_VCCR
BATTERY CHARGER
V_BUCK
B+
MIDRATE_2
V2
CR901
V1
V3
URXD
URXD_USBVM
URTS_USBXRXD
UCTS
UDSR
UDTR
UDCD
URI
INT5
INT4
UTXD2
INT5
AUDIO_IN
J900
TP16
V_BOOST
BATT_SER_D
ON_OFF
UDSR_CE
IVDD
INT4
UTXD
TP15
URI_CE
V_BUCK
UDTR
B+
VSIM1
UCTS_CE
V_BOOST
UDCD
V2
VSIM_EN
U903
UDSR
VR501
BB_SPI_CLK
BB_MOSI
BB_MISO
GCAP_SPI_CS
KEYPAD LED’s
SIM_PD0
LED_RED
ALRT_VCC
LED_GRN
VR801
GCAP_13MHz
PRS TriBand T280 (Panther2) 8488516k01_P13.5
VR910
VR909
KBR4
USB+
USB-
UDTR
J650
BOOM MIC
KBR6
VR904
BB_MISO
URI
AUDIO_OUT
KBC1
SDI_D_C
VR901
VR902
J910
MICROPHONE
DNP
VAG
V2
BL_SNK
V2
IRDA
V3
U1912
DIG_AUD(3:0)
U990
V2
IRDA_EN
IRDA_TX
B+
Q938
PA_DRV
SPEAKER
CONTACT PADS
ALRT_VCC
HS_SPKR
J904 SPK-
IRDA_RX
V2
ALERT
AL900
V2
U1906
UCTS2_SIM_RST1
UCTS_CE
J902 SPK+
VR903
V2
U1907
U1908
UTXD2
URXD2_SIM_RX1
URI_CE
UDSR_CE
URI
UDSR
DATALOG_N
VR907
VR908
UCTS
RX SIGNAL PATH
TX SIGNAL PATH
TEXT
TUNING VOLTAGES
13 MHz REFERENCE CLOCK
DATA BUS
ADDRESS BUS
REFERENCE SIGNALS
P280 - BLOCK DIAGRAM - PAGE 1/2
0
0
0
PCS
1
0
0
0
1
0
0
0
DCS_SW
1805-1880MHz
FL101
2
1
V1
7
V3
16 DCS/PCS
GSM
4
V2
2
9
FL102
U10
12
V4
14
U100 20
1930-1990MHz
RX
LOCAL
OSCILLATOR
FL100
CR200
24
3
2
16
4
13
2,5
FL104
B
5
C
N_GSM_SEL
N_DCS_SEL
RX_EN
U500
1,5,8
RX VCO MID CHANNELS
GSM: CH 62 -- 1347,4 MHz
EGSM: CH 37 -- 1342,4Mhz
DCS: CH 700 -- 1442,8MHz
PCS: CH 661 -- 1560MHz
1
20
4
2,75V RF_V1
14
17
PA_B+
U550
1
RF_IN
RF DET
+ -
3,14
4
5
+
INTEGR.
BUFFER
AMP
(Gain 1or 3)
+ SAT.
DET.
10
11 7
2
19
6 VCTRL
N_GSM_EXC_EN
5
4
1
2
Q410 Q410
3
6
Logic 1 at low power
Logig 0 at high power
GSM_EXC_SW
N_GSM_EXC_SW
DCS_SW
N_DCS_SW
DCS_SEL
N_RVCO
GSM_EXC_EN
N_GSM_EXC_EN
PAC_275
5V
Q451
E
B
GSM / DPCS SELECT CIRCUIT
For description of GSM / DPCS Select Circuit
see document on: gsm-service.fle.css.mot.com
3
B+
G1 1
N_RVCO
SF_OUT
DM_CS
1
2
TX VCO MID CHANNELS
GSM: CH 62 -- 902,4MHz
EGSM: CH 37 -- 897,4Mhz
DCS: CH 700 -- 1747,8MHz
PCS: CH 661 -- 1880MHz
TX VCO FRQ. RANGE
EGSM: 880-915Mhz
DCS: 1710-1785MHz
PCS:1850-1910MHz
N_GSM_EXC_EN
CR545 C
RES.
F1
H1
H2
C1
1,5V - 3,2V
9 10 7
U300
RX VCO
A1
B1
A3
A8
GSM DCS PCS
N_GSM_SEL
0
1
1
DCS_SEL
0
1
0
F9
C4
A4
12
14
B MATRIX
1
2
U1905
Q530
16
3,4
E
GSM_EXC_EN
11
U350
TX VCO
C7
STEP
ATT.
GPRS_TX
DEMODULATION
RXI
RX
RXQ
SPI
CP_TX
6
1,5V - 3,2V
F7
G9
( SCLK_OUT ) BCLKR
( SDFS ) BFSR
PHASE
DET
Divider
200KHz
to Patriot
( SDRX ) BDR
G8
8 Bits GPRS_TX - LOW
10 Bits GPRS_TX - HIGH
G1
H7, C8, J1
CP_RX
20
4
G2
N_GSM_SEL
DCS/PCS
PAC
COMP.
9 8
16
7-10
PAC_275
U400
15
SW_VCC
DCS_SEL
C
1
13MHz
16
12
D2
5 S1
2 S2
6 D1
B+
GSM
6-9
A7
C6
4
2,75V RF_V2
RX VCO FRQ. RANGE
EGSM: 1325 - 1360Mhz
DCS: 1405 - 1480MHz
PCS: 1530 - 1590MHz
Q450
C
Q201
B+
PA_B+
Q151
RF_V2
2,3,6,7
2
400MHz
FL103
N_DCS_SW
PLL
C8
RF_V1
400 MHz
1
23 6 22 10
GSM_EXC_SW
800MHz E9
U201
MAGIC
Q200
18
925-960MHz
TX FRQ. RANGE
EGSM: 880-915Mhz
DCS: 1710-1785MHz
PCS:1850-1910MHz
Osc.
discrete
circuty
1805-1990MHz
N_GSM_EXC_SW
J100
Mech. Ant Switch
A9
SUPER
FILTER
PCS
1
RF_V2
RX MID CHANNELS
GSM: CH 62 -- 947,4 MHz
EGSM: CH 37 -- 942,4Mhz
DCS: CH 700 -- 1842,8MHz
PCS: CH 661 -- 1960MHz
SWITCH
DCS
V1 V2 V3 V4
0 1 0 0
REG.
GSM
V1 V2 V3 V4 U10 / TX
0 0 0 1
GSM
DCS
0 0 1 0
RVCO
A10
U10 / RX
VRef
J7
13MHz VCO
CR201
H9, J9
MUX
J6
G6
MAGIC_13MHz
to Patriot
CLK_SELCT
from Patriot
Startup
Ref.
1 /2
PHASE
DET
AFC
Divider
Prog.
Divider
200KHz
REF.
REF. OSC.
E1
Y200 26MHz
26 MHz
PLL
LOGIC
CONTROL
SPI
G5
INTER
H4
FACE
J3
MAGIC_SPI_CS
RF_SPI_CLK
RF_MOSI
from Patriot
LP
FILTER
5V
13 1
2
RVCO
3
GSM DCS PCS
N_GSM_SEL
0
1
1
N_DCS_SEL
1
0
1
N_GSM_EXC_EN
0
1
1
1
0
0
GSM_EXC_EN
N_DCS_SEL
VCO
BAND
N_GSM_SEL
HPF
MODULATION
TXI
TX
TXQ
SPI
J2
G7
( SDTX ) BDX
( TX_CLK ) BCLKX
B5
BUFFER
ENABLE
AOC_DRIVE
AOC_DRIVE
B6
SAT_DETECT
SAT_DETECT
B4
DETECT_SW
DETECT_SW
A5
TX_KEY_OUT
TX_KEY_OUT
C5
PA
CONTROL
LOGIC
GPRS_TX
CONTROL
H8
J4
H5
RX_ACQ
DM_CS
TX_KEY
from Patriot
RX SIGNAL PATH
TX SIGNAL PATH
TUNING VOLTAGES
REFERENCE CLOCK
Orderable Part
Non - Orderable Part
P280 - BLOCK DIAGRAM - PAGE 2/2
12
1
17-20
E8
BACKl.
CONTR.
SR_CS
SR_VCC
E7
A8
SRAM
HOLD
F15
STBY
ON_OFF
PWR_SW
WDOG
N7
K5
C4
D6
J5
K13
C7
N6
CONV.
M5
H6
BATT_+
EXT_B+
THERM_BIAS
I_SENSE
UDSR
KEYPAD
LED´s
PWR_SW
KEYPAD
MATRIX
AND
JOYSTICK
S500
MIDRATE_1
B+
( to GCap)
CHRG_C
3 2
THERM_BIAS
3
4
Q944
4 1
GND
BATT+
1,2,5,6
V2
LED_RED
LED_GRN
RX SIGNAL PATH
J900
LS_SIM_CLK
CS7
P11 LS_SIM_RST
N10
CS5
SHIFT
SIM_I/O
M11
CS6
P10
SIM_CLK
N10
SIM_RST
N11
SIM_TX
P12
SIM_RX
LEVEL
Buck
Boost
Q942
BATT+
from EXT
PWR Cntl.
B+
B+
Q938
VIB
DRIVE
M7
to Vibra
N13
M8
to Q938
PA_DRV
B+ Sense
MAIN P6
J4,J10,J14
M9,P7
Switcher1
Switche2
E11
to U700,
B+
1.9V V1
URI
URXD2_SIM_RX1
G10
D14
BL_SNK
ALERT_VCC
BATT CONN.
J912
BATT_SER_D
Logic
LED
DRIVE
8
7
6
5 DISPLAY
3 CONN.
2
1
9
4
CHARGER
BATT_FDBK
AD
Q944
5
OVIC 1
U901
2
R918
L3
F14
GCAP_13MHZ
C7
C6
A2
RTC_BATT
MAGIC_13MHz
GCAP_CLK (32kHz)
ON
LOGIC
U900
GCAP3
U701,U703
to DSC
FLASH
Q1909
Q1908
Over voltage limit: 6,85V
Under voltage shut off: 2,67
EXT_B+
BATT_FDBK
URTS2_SIM_CLK1
Q1907
DATALOG_N
V2
TIMER
UCTS
UTXD2
UDSR_CE
EXT_BATT
( from CE Conn.)
7,8
3
S2
1 D1
4
S1 Q945 G2
D2
G1
2
5,6
BB_MOSI
SDI_D_C
RESET_OUT
DISP_SPI_CS
IVDD
BB_SPI_CLK
BL_SNK
ALERT_VCC
GND
KBC0, KBC1
KBR0, KBR1
KBR4 - KBR7
External PWR Contr.
V2
This resistor is IN the
Charger accessory and
is used for identification
CHARGE
BL_SNK
J700
A4,G4
E1,G6
U701
B4
FLASH
E7
F8
32 Mbit
C5
C4
B5
D3 EE Prom
RESET_OUT
RESET
K7
USB_PWR
F13
USB+
E9 USB
INTERF.
USBC9
Q1906
URI_CE
A6
B7
Y900
RESET
BB-SPI_CLK
BB_MOSI
BB_MISO
GCAP_SPI_CS
CNTL.
LOGIG
SPI
G13
H7
TIMER
INT4
INT5
MQSPI
PRIM
UART
C15
D14
GCAP
V_SIM1_EN
1.8V V3
10
U703
SRAM
2 Mbit
CR806
UCTS2_SIM_RST1
UCTS_CE
E1,D6
A1
B2
B5
A2
G5
V1
V3
BRST_CLK
FLASH_CS
OE_N
EB1_N
ADV_N
RESET_OUT
ECB_N
EXT_B+ ( to Charger )
SERIAL
AUDIO
SW_B+_EN
B+
INT4
INT5
UCDC
UDTR
NC
V3
EB1_N
EB0_N
CE2
OE_N
RW_N
AVDD, BVDD, OVDD, DVDD
V3
CVDD, EVDD, HVDD, IVDD, JVDD
J1
K3
U903
USB_PWR
USB+_UTXD
USB_URXD
OPTION1
OPTION2
UCDC
UDTR
AUDIO_IN
EXT_BATT
BATT_FDBK
U702
SRAM
2 Mbit
BATT_SER_D
G2
POWER
H14
Q600
Alert
E1,D6
A1
B2
B5
A2
G5
KBC0, KBC1
KBR0, KBR1
KBR4 - KBR7
ONE
WIRE
B2 CODEC
SERIAL
B1
INTERF.
N1
M2
J3
3,4
J910
1,2
SR_VCC
EB1_N
EB0_N
SR_CS
OE_N
RW_N
SDI_D_C
DISP_SPI_CS
KEYPAD
PORT
J10
G14 PRIM.
H11 UART
C10 B D
B10 B S
P
A10 I
n
B9
D10 t
N12
SPKSPK+
ON_OFF
AUDIO_OUT
SW_B+
2
J910
1
ADDRESS BUS
DATA BUS
EB1_N
EB0_N
CE2
OE_N
RW_N
BRST_CLK
FLASH_CS
ADV_N
ECB_N
SIM_CLK
SIM_RST
SIM_TX
SIM_RX
F3
E1
MQSPI
DISPLAY
L12
L11
L13
L14
Mic
USB / RS232
DATALOG
8
I
n
t
to SIM
6
4
5
13
14
9
11
16
3
2
T
i
m
e
to Magic
7
MQSPI
FSYNC
CLK_D
RX
TX
AUX_MIC
HS_SPKR
J904
J902
15
C5
F8
A4
D6
H12
C3
J9
A6
A7
C8
B6
A8
H7
SRDA_UF
STDA_UF
SC2A_UF
SCKA_UF
SPK
J901
UART
D5
E5
B5
C5
4
3
MAGIC_SPI_CS
RF_SPI_CLK
RF_MOSI
N15
L9
P12
N14
L8
D15
P13
N14
P14
J14
SIM
J13
INTER
J11
FACE
J12
PORT
AUDIO
D7
E8
B4
MEMORY
INTER
FACE
2ND
to U700
AL Board
J650
MQSPI
PRIM.
UART
K10
J15
K14
K13
U 902/DNP
SMART CONN.
J 903/DNP
12
13
10
11
BCLKR
BFSR
BDR
BDX
BCLKX
ESD Protection
3,8
5
2 U990 6
IRDA 7
MAGIC
A7
MIDRATE_1
SW_B+_EN
STBY
RX_EN
RX_ACQ
DM_CS
TX_KEY
CLK_SEL
RESET
IRDA_EN
IRDA_TX
IRDA_RX
B+
A14
F11
C13
G11
G10
F13
K4
C14
D13
F12
D13
N14
SPI_CS6
SPI_CS7
SPI_CS8
SW_B+2_EN
U700
PATRIOT
SIM
E2
F5
F7
F4
INT3
UTXD2
URTS2_SIM_CLK1
UCTS2_SIM_RST1
URXD2_SIM_RX1
Q900
V3
D12
UCTS
URI
UDSR
INT3_UF
UTXD2_UF
URTS2_UF
UCTS2_UF
URXD2_UF
SPI_CS6
SPI_CS7_UF
SPI_CS8
V2
B13
P1
H12
M13
14
1
3
4
2
15
16
9
7
VSIM_EN1
SIM_PD1
VSIM_EN1_UF
SIM_PD1_UF
V2
2.75V
2.75V V_REF
3/5V V_SIM1
6
5
8
SIM
CS2
CS3
CS1
VSIM1
TX SIGNAL PATH
TUNING VOLTAGES
REFERENCE CLOCK
Orderable Part
Non - Orderable Part
M810
ALERT_VCC
to Backlight LED ‘s and Alert
P280 - BOARD LAYOUT - PAGE 1/2
P280 - BOARD LAYOUT - PAGE 2/2
N_GSM_EXC_EN
DCS_SEL
N_GSM_SEL
DM_CS
SF_OUT
N_RVCO
B+
EXT_BATT
BATT+
B+
WATCHDOG
INT5
AUDIO_IN
GND
GND
GND
GND
16
17
18
19
20
13
AUDIO_OUT
INT4
12
15
UDSR
11
14
URI
UDTR
10
UCTS
SW_B+
7
UCDC
USB_PWR
6
9
USB_UXRD
5
8
EXT_BATT
USB+_UTXD
4
2
3
GND
BATT_FDBK
1
CE BUS
CONNECTOR
VREF
V1
5V
V3
VSIM1
V_BOOST
PAC_275
GSM_EXC_EN
J901
P280 - SIGNAL FLOW - PAGE 1/2
RF_V2
GCAP_CLK
M810
VIBRATOR
BTI
RTC Battery
U701
Flash/EEPROM
U300
ALERT Pads
L
F
U700
8
M
U400
400MHz
IF Filter
6
PAC IC
16 1
5
THERM
J
BATT_SER_D
F14
D12
C10 STDB
FL100
BFSR
SH300
J100
Ext. Ant. Conn.
10
5
6
7
8
9
11
1
RX_EN
12
Ant. Conn.
14
16
N_GSM_SEL
SW_VCC
DCS_SW
GSM_EXC_SW
EXT Conn.
J900
SIM Conn.
BDR
H
I
SH700
R
17
12 13 14 16
15
SH301
13
12
11
10
9
Q
8
U350
5
6
2
1
1
4 3 2 20
TX VCO
N
SH900
6
16
7
U550
9
DCS/PCS IPA
8
16
10
11
15
13
A
J901
M2
N1
SPKRM
A2
U500
4
Antenna Switch
A10
G BCLKR
GSM IPA
5
7 6
U10
CKIH
20
14
9
BCLKX
B9 SCKB
B10
SCOB_PC2A10
SRDB
1
2
3
5
B
N_DCS_SW
N_GSM_EXC_SW
PA_B+
GSM_EXC_EN
N_GSM_EXC_EN
N_DCS_SEL
N_GSM_SEL
PA_B+
GSM_EXC_EN
SF_OUT
N_TXVCO
V2
RX SPEAKER LINE -
RX VCO TUNING VOLTAGE
RX/TX VCO FEEDBACK LINE TO MAGIC
TX MIC LINE
BCLKX SIGNAL TO MAGIC
BDX SIGNAL TO MAGIC
TX VCO TUNING VOLTAGE
MAGIC_13MHz TO PATRIOT
M
N
O
P
Q
R
H
L
BDR SIGNAL TO PATRIOT
G
K
BFSR SIGNAL TO PATRIOT
F
RX SPEAKER LINE +
AMPLIFIED IF 400MHz
E
BCLKR SIGNAL TO PATRIOT
FILTERED PCS RX ANTENNA SIGNAL
D
I
FILTERED GSM RX ANTENNA SIGNAL
C
J
GSM/PCS RX ANTENNA SIGNAL
FILTERED DCS RX ANTENNA SIGNAL
B
DCS RX ANTENNA SIGNAL
GP05
TP202
A
VPP-1
VPP-2
TP17
RVCO
URXD
TP16
TP201
UTXD
TP15
TP18
DM_CS
RX_ACQ
TP14
TP8
TP13
TCK
MCU_DE
TP7
DSP_DE
TMS
TP6
GCAP_CLK
TRST
TP5
TP9
TDI
TDO
TP4
TP2
TP3
GND
RESET
TP1
TP
from MagicDM
TP11
N_DCS_SEL
E
K
SPKRP
B1AUXMICN
SC1B
from Patriot
O
CKOH_SCC_CLK
BATT+
8
CLK_IN
BDX
SH200
2nd DCS/PCS
Filter
C7
FQ32kHz
A6XTAL2C6
4
D
C
P
PATRIOT
GND
9
U900
GCAP III
A7
XTAL1
VSIM1
12
13
14
FL104
LS_SIM_RST
76
5
4
16
3
FRONTEND IC 2
18
1
22 23
19
24
J912
10
U100
L3
VSIM1
CKIL
SIM_IO
GND
Battery Conn.
12
13
Y900
RX VCO IC
32,768Mhz Crystal
AL900
SH100
LS_SIM_CLK
RVCO
GCAP_13MHz
I
MAGIC_13MHz TO PATRIOT
R
O
BDX SIGNAL TO MAGIC
N
TX VCO TUNING VOLTAGE
TX MIC LINE
BCLKX SIGNAL TO MAGIC
M
SF_OUT
P
RX/TX VCO FEEDBACK LINE TO MAGIC
L
RF_V2
Q
RX SPEAKER LINE RX VCO TUNING VOLTAGE
K
RX SPEAKER LINE +
BDR SIGNAL TO PATRIOT
BCLKR SIGNAL TO PATRIOT
H
RF_V2
J
AMPLIFIED IF 400MHz
BFSR SIGNAL TO PATRIOT
G
FILTERED PCS RX ANTENNA SIGNAL
E
BCLKX
RVCO
F
FILTERED DCS RX ANTENNA SIGNAL
FILTERED GSM RX ANTENNA SIGNAL
D
N_TX_EN
C
PAC_275
DCS RX ANTENNA SIGNAL
from Patriot
GSM/PCS RX ANTENNA SIGNAL
N_DCS_SEL
N_GSM_SEL
B
RF_V2
RF_V2
A
N_TXVCO
ALRT_VCC
RVCO
9
J650
SDI_D_c
SRAM
BB_MOSI
U702
8
U703
SRAM
RESET_OUT
L
7
SDTX J2
6
B1CP_TX
A1CP_RX
GND
K
J6
DISP_SPI_CS
Q
F7 G7
5
U201
IVDD
E
SCLK_OUT
EXC_EN
4
B5 GP03_DPM
3
PAC_275
SDFSG9
SDRX G8
O
BL_SNK
J902
A7PRE_IN
I
BB_SPI_CLK
M
H
2
1st
PCS Filter
BDR
G
BDX
F
CLK_OUT
BFSR
A
TX_CLK
FL102
N_GSM_EXC_SW
1
Speaker Pad +
5V
DISPLAY
CONNECTOR
GP05
TP202
N_GSM_EXC_EN
J700
VPP-1
RVCO
TP201
VPP-2
TP17
TP18
UTXD
URXD
TP16
TP14
RF_V2
GSM_EXC_SW
TP15
DM_CS
RX_ACQ
TP13
DSP_DE
GCAP_CLK
TCK
MCU_DE
TP8
N_RVCO
TP9
TMS
TP7
N_DCS_SEL
5V
TP11
TRST
DCS_SEL
TP6
IRDA
TP5
U990
TDI
D
TDO
C
TP4
N_EXC_EN
1st
GSM Filter
TP3
RX_EN
from Patriot
1st
DCS Filter
FL103
GND
DCS_SW
FL101
RESET
GSM_EXC_EN
DCS_SEL
TP2
RF_V2
RX_EN
TP1
EXC_EN
N_DCS_SW
TP
N_GSM_SEL
P280 - SIGNAL FLOW - PAGE 2/2
from Patriot
EXC_EN
B+
from Patriot
V1_FILT
RF_V1
B
P
BCLKR
R
MAGIC DM
A3PRSC_IN
MIC Conn.
J910
C246
J
N
26MHz Crystal
Y200
SH210
Speaker Pad -
J904
Display Conn
J700
HS CONN.
SH710
VREF
RF_V2
T280 L3 Parts List
Component Ref.
Part Number
Description
Component Ref.
Part Number
Description
A10
AL900
CR200
CR201
CR545
CR700
CR850
CR901
CR902
CR903
CR932
CR940
CR950
DS500
DS501
DS505
DS506
DS507
DS508
DS509
FL100
FL101
FL102
FL103
FL104
J100
J650
J700
J900
J901
J902
J904
J912
M810
Q151
Q200
Q201
Q202
Q203
Q204
Q351
Q410
Q450
Q451
Q530
Q600
Q932
Q938
3909155T04
3989402K01
4809877C09
4809877C10
4809948D12
4809606E02
4809948D42
4813833B10
4813833B10
4809924D18
4813833B10
4809653F07
4809948D42
4809496B11
4809496B11
4809496B11
4809496B11
4809496B11
4809496B11
4809496B11
9103769S05
9109069E04
9109239M12
9109450C06
9109487U02
0987984K02
0987837L01
0987817K02
3909426M04
0987636K06
3988929K01
3988929K01
3989331K01
5909382K05
4809527E30
4809527E24
4809579E48
5109522E73
4809579E48
4809579E39
4809579E35
4809939C32
4809579E49
4809940E02
4809527E26
5109817F45
4809579E29
4809579E29
CONTACT
CONTACT
BB555
BB659
BAR_63-02W
DAN222T
RB751V40
MBR0530T1
MBR0530T1
RB520S-30
MBR0530T1
MBRM120ET3
RB751V40
QSMG-H799
QSMG-H799
QSMG-H799
QSMG-H799
QSMG-H799
QSMG-H799
QSMG-H799
LFSN25N19C1897B
SAFC1842
855850
50C06
400MHz
CONN_J
CONN_J
CONN_J
C707
CONN_J
CONTACT
CONTACT
CONN_J
MOTOR
27E30
27E24
FDC6306P
NC7WZ08K
FDC6306P
FDG6323L
FDG6301N
EMH4
S16467DQ
DTC114YE
2SC5081
BPLUS_SWITCH
S13443
S13443
Q942
Q944
Q945
S500
S518
S519
S520
4809579E49
4809939C39
4887611L01
4070354A01
4009368L08
4009368L08
4009368L08
S16467DQ
EMD9
IFR7555
SWITCH
SWITCH
SWITCH
SWITCH
SH100
SH200
SH210
SH300
SH301
SH700
SH710
SH900
U10
U100
U110
U120
U1901
U1902
U1905
U1906
U1907
U1908
U1909
U1912
U201
U300
U350
U400
U402
U500
U550
U700
U701
U702
U703
U900
U901
U903
U990
VR501
VR801
VR901
VR902
VR903
VR904
VR907
VR908
VR909
VR910
VR940
VR948
Y200
Y900
2688524K01
2688525K01
2688527K01
2688526K01
2688530K01
2688528K01
2688529K01
2688531K01
5109572E38
5109944C42
5109522E74
5109522E74
2113743N38
2113743N38
5885924L07
5162852A59
5162852A59
5162852A59
5162852A59
4809788E06
5109879E50
4809283D80
4809283D90
5109923D50
4809939C34
5109730C47
5109730C48
5195015D07
5199443A01
5109509A36
5109509A39
5109879E82
5109731C32
4809606E12
5162852A33
4809788E06
4809788E06
4809788E06
4809788E06
4813830M74
4813830M74
4809788E06
4809788E06
4809788E06
4809788E06
4809788E06
4809948D18
4809612J42
4809995L09
SHIELD
SHIELD
SHIELD
SHIELD
SHIELD
SHIELD
SHIELD
SHIELD
AC_717
MC13709
NC7ST08
NC7ST08
CAP, 33pF
CAP, 33pF
RAC10-1A-6
MAX4599EXT
MAX4599EXT
MAX4599EXT
MAX4599EXT
UDZTE-176.8B
79E50
ATXN1007T
ATXN1000B
23D50
EMB10
UPG2117K, GSM
UPG2118K, DCS
SC29803
43A01
KM616FR4010
CY62137V18
79E82
MC33645
EMIF11
HSDL3202
UDZTE-176.8B
UDZTE-176.8B
UDZTE-176.8B
UDZTE-176.8B
MMBZ6V8ALT1
MMBZ6V8ALT1
UDZTE-176.8B
UDZTE-176.8B
UDZTE-176.8B
UDZTE-176.8B
UDZTE-176.8B
SMS05
12J42
MC146
MOTOROLA, the Stylized M Logo, and all other trademarks indicated as such herein are trademarks of Motorola, Inc.
® Reg. U.S. Pat. & Tm. Off.
TrueSync is a trademark of Starfish, Inc., a wholly owned independent subsidiary of Motorola, Inc.
All other product or service names are the property of their respective owners.
 2001 Motorola, Inc.
All rights reserved.
Personal Communications Sector,
1500 Gateway Blvd.
Boynton Beach, FL 33426-8292
Printed in U.S.A. 05/01
@6881038B15@
6881038B15-O

Product Family B58

Transcription

Similar documents

NAUTICO UTICO 3 NAUTICO UTICO 3

318CTB - RCS: Remote Control Solutions

LIFEPAK 500 Maintenance Checklist

Light Options – There are 3 dual LED strips in the

GSM Security Camera - Jablotron Security

DOS SD-STD-02.01 K12 L3 ASTM F2656 M50 P1

Lambourgini Murcielago Ride On Car Manual

Battery Guide V3

Mega Plexxus Instruction