chapter 3>> connecting pvr

Transcription

>> WARNING
Your Open Box Dual Tuner PVR has been manufactured to meet international safety
standards, but you must take notice of the following safety precautions carefully.
MAINS SUPPLY
Open Box PVR operates with 90–250V AC 50/60 Hz mains supply. Do not connect any
of your equipment (Open Box PVR, TV, VCR, etc.) to the mains supply until you have
properly connected all the other leads.
OVERLOADING
Do not overload wall outlets, extension cards or adapters as these can result in fire or
electrical shock.
LIQUIDS
Keep liquids away from the PVR. The apparatus shall not be
exposed to dripping or splashing and that no objects filled with
liquids, such as vases, shall be placed on the apparatus.
SMALL OBJECTS
Coins or other small objects must be kept away from the PVR as they can fall through the
ventilation slots of the PVR and cause serious damage.
CLEANING
Disconnect the PVR from the wall socket before cleaning it. Use
a dry cloth lightly dampened (no solvents) to clean the exterior of
the PVR.
VENTILATION
Do not block the PVR's ventilation slots. Ensure that a free airflow is maintained around
the PVR.
Never stand the PVR on soft furnishings or carpets. Do not use or store the PVR where it is
exposed to direct sunlight or near a heater.
1
>> CONTENTS
ATTACHMENTS
Do not use any attachments that are not recommended as these may cause hazards or
damage the equipment.
CONNECTION TO THE SATELLITE DISH LNB
Disconnect the PVR from the mains before connecting or disconnecting the cable from
the satellite dish. Failure to do so can damage the LNB.
GROUNDING
The LNB cable must be earthed to the system earth for the satellite dish.
LOCATION
Locate the PVR indoor avoid possible damage from lightening, raining and direct sunlight.
In order to ensure a free flow of air around the PVR allow at least 10 cm of space above and
on all sides, especially between the PVR and TV.
RESPONSIBILITY
Do not use the PVR and its contents for illegal purpose. We are not responsible for any
kind of illegal use. Do not use the PVR to backup important data. It can be deleted. We are
not responsible for any kind of problems caused by application programs.
GENERAL INFORMATION _________ 4
HARDWARE DESCRIPTION ________ 6
FRONT PANEL
REAR PANEL
REMOTE CONTROL UNIT
CONNECTING PVR ____________ 10
CONNECTING TO TV
CONNECTING TO THE SATELLITE ANTENNA
CONNECTING TO VCR
CONNECTING TO AUDIO
CONNECTING TO PC
CONNECTING TO USB DEVICES
CONNECTING TO OTHER PVR USING SERIAL CABLE
GETTING STARTED ____________ 17
EASY INSTALLATION
1 SELECT LANGUAGE
2 SELECT ANTENNA CONNECTION TYPE
3 SELECT A SATELLITE FOR TUNER
4 SATELLITE SETUP
5 CHANNEL SEARCH
6 TIME SETUP
BASIC OPERATION ____________ 21
CHANNEL INFORMATION BOX
LIVE MODE _________________ 24
BASIC CHANNEL NAVIGATION
EXTENDED FUNCTION KEYS
INSTANT RECORDING
STOP RECORDING
TIMESHIFT
TELETEXT
PICTURE IN PICTURE
PLAYING MODE ______________ 30
PLAYBACK CONTROL
BOOKMARK
SETTING UP UHF MODULATOR
SETTING UP TIME
CI (COMMON INTERFACE)MODULES
PVR MANAGEMENT
ERASING DATA
CONNECTED USB DEVICES
INSTALLATION ________________ 46
USING EASY INSTALLATION
SETTING UP ANTENNA MODE
SETTING UP ANTENNA
USING CHANNEL SEARCH
MANUAL CHANNEL SEARCH
ADVANCED CHANNEL SEARCH
USING MOTORIZED ANTENNA CONTROL
USING EDIT SATELLITE
USING EDIT TRANSPONDER
USER PREFERENCE _____________ 55
LANGUAGE
TIMER
PARENTAL LOCK
APPEARANCE
PVR SETUP
EPG SETUP
RECORDING LIST _____________ 59
EDIT RECORDING
REMINDER LIST _______________ 63
RECORDING RESERVATION CONFLICT
MULTIMEDIA/GAMES __________ 65
USING MP3 PLAYER
MP3 PLAYER MODE
USING MP3 FILE OPERATION
USING PHOTO ALBUM
USING JPEG FILE OPERATION
USING GAMES
USING PLUG–INS
MAIN MENU ________________ 33
MULTIMEDIA COMMUNICATION WITH
PC SOFTWARE _______________ 71
CHANNEL GUIDE _____________ 35
MENU MAP _________________ 76
ORGANIZE CHANNEL __________ 36
GLOSSARY __________________ 77
USING EDIT CHANNEL
USING EDIT FAVORITE GROUP
PROGRAM GUIDE _____________ 39
TROUBLESHOOTING ___________ 79
TECHNICAL SPECIFICATION ______ 80
SYSTEM SETUP _______________ 41
SETTING UP TV
2
3
CHAPTER
1>>
GENERAL INFORMATION
THANK YOU FOR PURCHASING OPEN BOX DUAL TUNER PERSONAL VIDEO RECORDER (PVR)
Open Box PVR is fully compliant with the international DVB standard and thus transmits
digital images, sounds, information guides and teletext directly to your TV through the
satellite. Now you can comfortably see and receive digitally transmitted music, news, movie
and sports satellite broadcasts in your office or at your home.
This PVR is equipped with an internal hard disk drive used to record and playback TV and
radio programs. It also has two tuner inputs from your satellite dish, allowing you to view or
timeshift one channel while simultaneously recording two more channels. Just push pause or
record key and you will be always accessible to your preferred programs.
One of the distinctive features of Open Box PVR is multimedia functionalities. You can
plug your digital camera directly into the USB connector on the front panel and you can
enjoy viewing photos on TV with your family and friends. Not just digital camera, but also
MP3 player can be played in the same way. JPG photos and MP3 files can be stored in the
PVR very easily without having to use PC. Interesting games are embedded in this PVR and
you can enjoy playing them on TV. What’s more, an advanced PC Software is provided,
allowing you to play videos or view photos on PC as well. Open Box PVR is future proof and
its advanced and comprehensive features will make you satisfied with any current and future
applications. Open Box PVR will turn your TV into the center of all digital devices of home!
Open Box PVR operates by a user friendly and full graphic menu available in a variety of
languages. Installation Guide will guide you through installation procedures which otherwise
can be cumbersome. If you are a sophisticate user of satellite receiver, you can instead
search channels using the manual search mode.You can save up to 3,500 TV and 1,500
Radio channels and you can edit the searched channels using Favorite, Lock, Delete, Move,
and Sort functions. All functions can be carried out using the remote control and some of the
functions can also be carried out using the keys on the front panel.
This PVR will be updated with new software, if necessary, which may change some of the
functions of the PVR. If you have any difficulties concerning the operation of your PVR,
please refer to the relevant section of this manual, including the Troubleshooting. This
Manual will provide you with useful information on using the PVR.
FEATURES
• 80GB HDD, Recording for 40~56 hours
• Dual Tuner
• Time–Shifting (playback with time delay)
• Recording Two Channels While Watching or Time–Shifting another Channel
• Trick Play (FF/ REW/ PAUSE/ SLOW )
• Recording Reservation Using EPG and Timer
• Bookmark Function
• Encrypted Channel Recording & Playback, Optional Decrypted Recording Supported
• Software PIP
• True Color OSD
• USB 1.1 Host Controller – For instant interface with MP3 and digital camera
• Supports Direct USB connection to Digital Cameras from various vendors: Canon, Sony,
Nikon, Fuji, Olympus, Samsung, Casio and so on.
• USB 2.0 Device Controller – For instant interface with PC
• Built–in Photo Album and Slide Show
• Built–in MP3 Player
• 3500 TV Channels & 1500 Radio Programmable
• Channel List Editing & Favorite List Editing
• Subtitle & Teletext Subtitle supported
• Teletext supported
• S/PDIF for digital audio or Dolby AC–3 bit stream output
• Video editing
YOUR PVR INCLUDES THE FOLLOWING COMPONENTS
PVR
Remote Control Unit
& AAA battery
(option)
SCART Cable
CD including PC
Software
+10%
-10%
4
5
CHAPTER
2>>
HARDWARE DESCRIPTION
FRONT PANEL
REAR PANEL
LNB 1/2 IN
Connects the satellite antenna cable.
TV SCART
Connects the TV SCART.
Power
To switch between On and Standby mode
MENU
S/PDIF
Optical output for Digital Audio
RF OUT
Connects the TV RF IN (ANT IN).
SCART – TV
TUNER 2 IN
TUNER 1 IN
TUNER 2 OUT
TUNER 1 OUT
SCART – VCR
RS232
Upgrades the PVR Program
software.
Two slots for CA module
with smart card
RF IN
Connects the TV.
USB port 1.1
USB 2.0
Connect to PC
CH–/+
Channel up and down, Vertical
navigation
VOL–/+
Volume up and down, Horizontal navigation
Video, Audio L/R
Connect to a TV using RCA jack
OK
VCR SCART
Connects the VCR SCART.
LNB 1OUT
Use it to connect to another PVR or LNB 2 IN.
LNB 2 OUT
Use it to connect another STB.
6
7
REMOTE CONTROL UNIT
REMOTE CONTROL KEY DESCRIPTION
Mute
You can toggle between normal audio and muted audio.
Standby
You can switch between Turn On and Standby.
OPT
You can manage channel options; select audio and subtitle
and add channel to the favorite list.
Text
You can see Teletext if there is Teletext information in the
channel.
Number
You can select channel by entering number. Selects menu
by choosing number.
Pre CH
You can switch back to the previously viewed channel.
Exit
10%
10%
OK
You can select item in menu mode. You can show channel
guide window when watching live TV. You can show time
slider when watching recorded TV.
Info
You can see channel information in live mode. You can
show channel information in EPG window. You can show
recorded program information in recorded program list.
EPG
You can see EPG window when watching live TV.
RED
You can see the program being recorded.
GREEN
In play mode, you can see bookmark list of the recording.
YELLOW In play mode, you can jump forward to next 10 % of the
recording.
BLUE
In play mode, you can jump backword to previous 10 % of
the recording.
[Note] Color buttons have a variety of use in each different
window. Please refer to the instructions in help panel below.
8
You can switch to normal play.
FF
You can fast-forward playback in five steps (x2, x4, x8,
x16, x24).
You can stop recording when channel is recorded.
In Play Mode, you can stop the current play and switch
back to Live Mode.
You can exit from any menu and switch back to the screen.
Volume Up /Volume Down (Left Arrow /Right Arrow)
You can control audio volume. You can move left and
right in menu mode.
Play
Stop
You can see top menu window when watching live TV.
You can switch back to the previous menu window in menu
mode.
Channel Up /Channel Down (Up Arrow /Down Arrow )
You can change channel up and down. You can move up
and down in menu mode.
You can rewind playback in five steps (x2, x4, x8, x16,
x24).
You can start up timeshift when automatic timeshift option
is enabled.
In Live mode, you can see the list of recorded program.
TV/Radio You can toggle between TV mode and Radio mode.
Menu
REW
10%
10%
Pause
You can pause the watching program and start up
timeshift.
Slow
You can start slow motion play in seven steps.
REC
You can record the program when watching live TV.
REMINDER You can set up a schedule to record TV Program. Reminder
list window appears when watching live TV.
RECORDING You can see the programs being recorded when watching
live TV.
FAV
You can see the favorite group list when watching live TV.
Jump –
You can jump backward to 30 seconds before,when
watching recorded program.
Jump +
You can jump forward to 30 seconds after,when watching
recorded program.
Bookmark You can set a bookmark point when watching recorded
program.
SAT
In play mode, you can jump to the next bookmarked point.
In live mode, you can see satellite list window when
watching live TV. It provides easy access to the channel list
of each satellite.
UHF
You can set up UHF modulator.
TV/SAT
Press number 0 button, you can toggle between VCR
through and Internal A/V.
PIP
You can use the Picture in picture to watch different
program at the same time.PIP window appears when
watching live TV.
9
CHAPTER
3>>
CONNECTING PVR
To set up PVR, you should connect your PVR to satellite antenna and TV. You can
connect to TV using SCART cable or composite cable. Because PVR has two tuners, you can
make connection to antenna in various ways. Also you can connect to other devices to use
extended features: VTR, Digital Audio Amplifier, PC and USB devices.
• CONNECTING TO TV USING THE RF CABLE
Plug in RF cable to the RF output port on your PVR; then connect the other end to TV.
SCART – TV
✍ Note>>>
TUNER 2 IN
TUNER 1 IN
TUNER 2 OUT
TUNER 1 OUT
SCART – VCR
If you get any problem to connect your PVR,, contact local distributor.
CONNECTING TO TV
You can connect PVR to TV via SCART cable, Composite cable and RF cable.
TV
• CONNECTING TO TV USING SCART CABLE
Plug the SCART cable in to the SCART input port on your PVR; then connect the other
end to TV.
TV
CONNECTING TO THE SATELLITE ANTENNA
SCART – TV
TUNER 2 IN
TUNER 1 IN
TUNER 2 OUT
TUNER 1 OUT
SCART – VCR
Because PVR has two tuners,you can select antenna setup mode:loop through, sameseparated and different-separated.
• LOOP THROUGH
Only tuner 1 is connected to the antenna. Connect the antenna cable to the tuner 1 input
port on your PVR. Connect the appropriate cable to the tuner 1 output port; then connect the
other end to tuner 2 input port.
• CONNECTING TO TV USING THE COMPOSITE VIDEO AUDIO CABLE
Plug the composite video audio cable in to the video audio output port (RCA-type output
port) on your PVR; then connect the other end to TV.
TV
✍ Note>>>
During recording, you can watch only limited channel. When recording goes on, you can watch channels in the
same polarity of the channel being recorded.
1 Antenna
SCART – TV
TUNER 2 IN
TUNER 1 IN
TUNER 2 OUT
TUNER 1 OUT
SCART – VCR
SCART – TV
TUNER 2 IN
TUNER 1 IN
TUNER 2 OUT
TUNER 1 OUT
SCART – VCR
10
11
• SAME-SEPARATED
CONNECTING TO VCR
Tuner 1 and tuner 2 are connected to the antenna each. Even during recording, you can
watch all the channel. Connect the antenna cable to the tuner 1 input port, and connect the
other antenna cable to the tuner 2 input port. Two tuners share the same broadcasting signal
from one antenna.
• CONNECTING TO VCR USING SCART CABLE
Plug in the SCART cable to SCART output port on your PVR; then connect the other end
to VCR.
When you set up, you should select "Separated" in connection type.
For more information,see ”Easy Installation” on page 17.
SCART – TV
TUNER 2 IN
TUNER 1 IN
TUNER 2 OUT
TUNER 1 OUT
SCART – VCR
1 Antenna
VCR
SCART – TV
TUNER 2 IN
TUNER 1 IN
TUNER 2 OUT
TUNER 1 OUT
SCART – VCR
• CONNECTING TO VCR USING THE COMPOSITE VIDEO AUDIO CABLE
• DIFFERENT-SEPARATED
Connect the antenna cable to the tuner 1 input port, and connect the other antenna cable
to the tuner 2 input port. Each tuner get the different broadcasting signal from different
antenna. When you set up, you should select "Separated" in connection type.
Plug in the composite video audio cable to video audio output port (RCA-type output
port) on your PVR, then connect the other end to VCR.
For more information, see “Easy Installation” on page 17.
SCART – TV
TUNER 2 IN
TUNER 1 IN
TUNER 2 OUT
TUNER 1 OUT
SCART – VCR
2 Separated
Antennas
VCR
SCART – TV
TUNER 2 IN
TUNER 1 IN
TUNER 2 OUT
TUNER 1 OUT
SCART – VCR
12
13
CONNECTING TO AUDIO
CONNECTING TO PC
• CONNECTING TO THE HI-FI SYSTEM
• CONNECTING TO PC USING USB CABLE
Connect composite audio cable to the hi-fi audio system and connect the other end to
your PVR.
You can connect PVR to PC with included USB cable. Plug in the USB cable to the USB
2.0 port on your PVR; then connect the other end to PC USB 2.0 port. After connecting to
PC, you can use included PC program to manage multimedia data in your PVR: MP3, JPEG,
Recorded Video and so on.
Audio system
For more information, see "USB ports" on page 71.
SCART – TV
TUNER 2 IN
TUNER 1 IN
TUNER 2 OUT
TUNER 1 OUT
SCART – VCR
SCART – TV
TUNER 2 IN
TUNER 1 IN
TUNER 2 OUT
TUNER 1 OUT
SCART – VCR
PC
• CONNECTING TO DIGITAL AUDIO EQUIPMENT USING S/PDIF CABLE (SONY/PHILIPS
DIGITAL INTERFACE)
If you have digital audio equipment, you can connect it to PVR using S/PDIF Plug in the
appropriate cable to the S/PDIF port on your PVR, then connect the other end to digital
audio equipment.
SCART – TV
TUNER 2 IN
TUNER 1 IN
TUNER 2 OUT
TUNER 1 OUT
SCART – VCR
• CONNECTING TO PC USING SERIAL CABLE
You can connect PVR to PC using Serial cable (RS-232-C). Connect the appropriate serial
cable to the serial port on your PVR; then connect the other end to PC. PVR has 4-pin and 9pin serial port. You can transfer channel data with Satco-DX application.
For more information, see page 44.
SCART – TV
TUNER 2 IN
TUNER 1 IN
TUNER 2 OUT
TUNER 1 OUT
SCART – VCR
Digital Amp
PC
14
15
CHAPTER
4>>
GETTING STARTED
CONNECTING TO USB DEVICES
EASY INSTALLATION
You can connect USB storage device and USB camera from various manufacturers:
Canon, Sony, Nikon, Olympus, Samsung and so on. Plug in the appropriate USB cable to the
USB port in the front of your PVR; then connect the other end to the USB device. You can
see the files in the device when you use "MP3 player" or "Photo Album".
PVR provides the step-by-step installation feature. If no channel exists, Easy Installation
window appears when you first purchase your PVR or when you do Factory Default so that
no channels are stored. And you can also choose [Main Menu] >>[3 Installation] >>[1 Easy
Installation] later.
Easy installation steps are listed as below:
CA
Slot 1
USB
Slot 1
1
Select Language
2
Select Antenna Connection Type
3
Select a Satellite for Tuner
4
Satellite Setup
5
Channel Search
6
Time Setup
Press [Green] button to move to the next step and press [Red] button to go back to the
previous step. You can quit Easy Installation by pressing [Exit] button.
USB Storage device
or USB camera
1 SELECT LANGUAGE
Select Language by pressing [Right Arrow] button or [Left Arrow] button. Supported
languages are English, Italian, Turkish and Russian.
CONNECTING TO OTHER PVR USING SERIAL CABLE
You can connect your PVR to other PVR using serial cable. You can update firmware and
transfer channel data. You can easily share setup configuration with other PVR.
Your PVR has two integrated satellite tuners, so you can make connection to satellite
antenna in various ways: Loop-Through, Same-Separated and Different-Separated.
SCART – TV
TUNER 2 IN
TUNER 1 IN
TUNER 2 OUT
TUNER 1 OUT
SCART – VCR
SCART IN
TUNER 1 IN
TUNER 2 IN
TUNER 1 OUT
TUNER 2 OUT
SCART OUT
Other receiver
2 SELECT ANTENNA CONNECTION TYPE
If Tuner 2 input port is connected to Tuner 1 output port, you should select “Loop
Through”. And If Tuner 2 input port is separated from Tuner 1, you should select
“Separated”. When you choose “Separated”, “Tuner 2 Signal Configuration” is available. If
Tuner 2 input is connected to the same antenna with Tuner 1, for example dual LNB
antenna; then you should select “Same as Tuner 1”. If Tuner 2 is connected to different
antenna from Tuner 1; then you should select “Different
from Tuner 1”.
✍ Note>>>
If you have any problem, contact local distributor.
16
17
3 SELECT A SATELLITE FOR TUNER
• TO ADD A SATELLITE FOR TUNER
Scroll the list by pressing [Up Arrow] button or [Down
Arrow] button; then select a satellite by pressing [OK]
button. Most popular satellites are shown on the top of list.
You can select a continent you want by pressing [Blue]
button; then you can view the list arranged by the selected
continent: Europe, Asia, Atlantic, America and All.
• TO REMOVE SATELLITE
You can toggle focus between the two lists by pressing
[Yellow] button. Move focus to the right side list; then remove a satellite by pressing [OK]
button.
✍ Note>>>
If you select “Different-Separated” in the previous step, you should add satellite for each tuner 1 and tuner 2:
you should do this step twice.
4 SATELLITE SETUP
You can configure each satellite you choose: LNB Type,
LNB low frequency, LNB high frequency, 22kHz Control
and DiSEqC input.
• TO SET UP LNB
Choose “LNB Type”; then press [Right Arrow] button or
[Left Arrow] button. You can select LNB Type: 5150, 9750,
10750, 11300 and Universal. Your PVR suggests a proper
LNB Type and LNB Frequency by analyzing the satellite
information. Press [OK] button to set up detailed information:
LNB Type, LNB low frequency and LNB high frequency.
• TO SET UP 22KHZ SWITCH CONTROL
Choose “22kHz Control”; then select “On” or “Off”.
• TO SET UP DISEQC INPUT
Choose “DiSEqC Input”; then select proper DiSEqC input: 1/4, 2/4, 3/4, 4/4, Mini A, Mini
B and Disable.
• TO CHECK SATELLITE SIGNAL
You can see the satellite signal quality at the right side in the window. Choose
“Transponder”; then select Transponder in the satellite. You can also see the specific
transponder signal quality. Channel in the transponder will be shown if it is available to
receive broadcasted signal.
• TO SET UP MOTORIZED ANTENNA
Choose “Motorized Antenna”; then press [OK] button.
✍ Note>>>
If you select “Same-Separated” in the previous step, you should choose which tuner is connected to motorized
antenna.
18
19
CHAPTER
5 CHANNEL SEARCH
After setting up all the satellite you select, channel
search dialog appears. You can save satellite configuration
and start searching channel by selecting OK and pressing
[OK] button.
• TO CANCEL SEARCHING CHANNEL
Press [Red] button to cancel searching.
✍ Note>>>
If you stop searching, only those channels searched before you cancel the process will remain and move to the
next procedure: Time Setup.
6 TIME SETUP
The correct time setting is critical to many functions in PVR; your PVR provides two ways
of time setting: Manual Time Setting and Automatic Time Setting
• MANUAL TIME SETTING
You can set current time and day manually. PVR keeps the current time until power cable
is plugged off. When PVR gets started up again, Time Setup window will appear; then you
have to set the current time.
5>>
BASIC OPERATION
Your PVR has four operation modes. Functions are slightly different according to the
current operation mode. Operation modes are listed as below:
• LIVE
Live mode is when you watch live program: TV or Radio.
• TIMESHIFT
Timeshift function comes in handy when you have to briefly stop watching TV to answer
the door or the phone. If you push the pause key, from then the channel starts to be
recorded. When you return and push the pause or play key, you can view the program
from the spot you stopped. So, it will be same as viewing a live program. Timeshift mode
refers to this mode.
• RECORDING
Recording mode is when you record channels while watching a live program.
• PLAYING
Playing mode is when you watch a recorded program.
✍ Note>>>
You can see check current mode by pressing [Info] button.
• AUTOMATIC TIME SETTING
To avoid the troublesome manual setting, your PVR provides automatic time setting. After
selecting “Auto” in Time Mode, set your local time in Set Local Time. Select a channel to
receive time data; then the current time is synchronized to the time information of the
channel that you specified. When PVR gets started up, you don’t need to set up time.
✍ Note>>>
If Time Mode is Automatic, your PVR shows the channel defined for automatic time setup when PVR starts up
after disconnecting power. If Time Mode is Manual, your PVR show the last watching channel.
• TO FINISH EASY INSTALLATION
After setting up time, choose “OK”; then press [OK] button.
20
21
• TO START UP
Press [Power] button to start up PVR.
• TO CONTROL VOLUME
Press [VOL–] button or [VOL+] button to control
volume.
• TO SET UP UHF
Press [UHF] button to set up UHF; UHF Setup window appears.
• TO SEND SIGNAL THROUGH TO VCR
Press [TV/SAT] button to toggle between VCR--through and Internal A/V.
CHANNEL INFORMATION BOX
• TO MUTE AUDIO
Press [Mute] button to toggle between normal audio
and muted audio.
Channel Information Box show general information about current PVR operation and
channel status.
Channel Number
Channel Name
Channel Group : Selected Favorite Group Name
Operation Mode : Live, Timeshift, Recording and Playing
Current Time : Weekday and Time
Subtitle, Teletext and Program Rating
Tuner Number and Signal Quality
• TO CHANGE AUDIO TRACK
Press [OPT] button; then select the audio track of the
program.
FTA or CAS
Audio Track And Audio Count
EPG : Next program in EPG
• TO CHANGE AUDIO OUTPUT
• TO SEE CHANNEL INFORMATION
Press [OPT] button; then select the audio output: stereo,
left mono and right mono.
Press [Info] button to see channel information box. Also, you can see detail channel
information by pressing [Info] button when channel information box appears.
• TO CHANGE SUBTITLE
Press [OPT] button; then select the subtitle.
• TO ADD CURRENT CHANNEL TO THE FAVORITE
Press [OPT] button; then select "Favorite" and press [OK] button. And you can select the
favorite group you want.
22
23
CHAPTER
6>>
LIVE MODE
Live mode is when you watch live program. It is the default operation mode when PVR
gets started up.
Hot keys are provided for easy access.
• TO SEE RECORDED PROGRAM LIST
Press [Recording] button to see Recorded Program List Window.
For more information, see "Recording List" on page 59.
BASIC CHANNEL NAVIGATION
• TO SEE FAVORITE LIST
• TO NAVIGATE CHANNEL
Press [FAV] button to see Favorite Group Window. Select a Favorite Group; then select
channel in the favorite group you choose.
You can navigate channel by pressing [Up Arrow] button or [Down Arrow] button.
✍ Note>>>
Channels can be navigated in a selected channel group. You can change channel group by selecting favorite
group. Press [FAV] to change favorite group.
• TO CHANGE CHANNEL
You can change channel by pressing channel number.
For more information about Favorite Group, see page 38.
• TO SEE TOP MENU
Press [Menu] button to see Top Menu Window.
• TO SEE EPG
Press [EPG] button to see EPG Guide Window. You can see EPG information in the
channel, and make instant reservation to record or tune TV programs.
For more information, see "Program Guide" on page 39.
• TO SWITCH BETWEEN TV AND RADIO
Press [TV/Radio] button to switch between TV service and Radio Service.
• TO JUMP TO PREVIOUS CHANNEL
You can jump to the previously watched channel by pressing [PreCH] button.
EXTENDED FUNCTION KEYS
• TO SEE RECORDED CHANNEL LIST
Press [Red] button to see Recorded Channel List; the
Recorded Channel Dialog only appears when PVR records
channels. You can switch to the channel being recorded
by selecting it on the list.
• TO SEE CHANNEL GUIDE
Press [OK] button to see Channel Guide Window. Channel Guide help you to find the
channel you want.
For more information, see "Channel Guide" on page 35.
• TO SEE SATELLITES AND ITS CHANNELS
Press [SAT] button to see Satellite List. You can easily access the channels in the specific
satellite.
• TO SEE REMINDER LIST
Press [Reminder] button to see Reminder List Window. You can make instant reminder to
record or tune a TV program.
For more information, see "Reminder List" on page 63.
24
25
INSTANT RECORDING
TIMESHIFT
You can record program instantly when watching live program. If you press [REC] button;
then Recording Dialog appears. Recording options such as starting record time, duration and
decryption can be configured. If you want to record immediately, just press [OK] button.
Recording starts after 5 seconds if there is no response.
When you have to briefly stop watching TV to answer the door or the phone, you can
start timeshift recording of the channel you were watching. This way you can continue
watching it from the spot that was paused.
• TO START TIMESHIFT
Press [Pause] button to start timeshift. You can pause a live program and in this state
recording of the paused channel starts.
And then press [Play] button or [Pause] button again to view the paused live channel.
Operation mode is switched from Live mode to Timeshift mode.
• TO START TIMESHIFTING PROGRAM AUTOMATICALLY
• TO SELECT TIME TO START RECORDING
Choose “Start Record”; then select start time by pressing [Right Arrow] button or [Left
Arrow] button. You can start recording within two hours. You can also start recording
immediately.
When automatic timeshift option turns on, Timeshift function automatically starts
whenever you change channel. Press [REW] button or [Jump–] button; then you can rewind
the program. Operation mode switches from Live mode to Timeshift mode.
For more information about automatic timeshift option, see “Automatic Timeshift” on
page 59.
• TO SELECT RECORDING DURATION
Choose “Duration”; then select Recording Duration, 4 Hours duration is default. You can
change duration from every one minute up to 10 Hours.
Also you can change the recording duration by pressing color button;
_Red button ➝ Decrease the recording duration by 1 hour
_Green button ➝ Increase the recording duration by 1 hour
_Yellow button ➝ Decrease the recording duration by 10 minutes
_Blue button ➝ Increase the recording duration by 10 minutes
• TO FORCE DECRYPTION WHILE RECORDING
Choose “Force Decryption”; then select “On” to force decryption. By default, your PVR
does not decrypt it when recording encrypted channel.
STOP RECORDING
• TO STOP RECORDING
Press [STOP] button to stop recording: when recorded
program exists, Stop Recording Dialog appears. It shows
Recorded Channel Number, Channel Name and
Recording Duration. You can select the channel to stop
recording, and press [OK] button.
26
27
TELETEXT
PICTURE IN PICTURE
Your PVR decodes Teletext information and provides some functions to navigate teletext
pages.
You can watch two channels simultaneously using PIP. Press [PIP] button to start PIP.
Press [PIP] button again to close PIP screen.
• TO START TELETEXT
Press [TEXT] button to see teletext.
• TO GO TO NEXT OR PREVIOUS PAGE
Press [Up Arrow] button to go to next page; Press [Down Arrow] button to go to previous
page.
• TO NAVIGATE LINK ON THE WINDOW
Press [Right Arrow] button or [Left Arrow] button to navigate links on the teletext window.
Press [OK] button to go to the page.
• TO SEE SEARCH SPECIFIC PAGE
Press Page Number on remote control.
• TO GO BACK TO DEFAULT PAGE
Press [Red] button to go back to default page.
• TO NAVIGATE HISTORY PAGES
Press [Green] button to go back to the previous page in history list; Press [Yellow] button
to go forward to next in history list.
• TO TOGGLE SCREEN
• TO CHANGE PIP CHANNEL
PIP Channel list window appears by pressing [Blue]
button. You can select PIP channel in the list.
• TO SWITCH CHANNEL BETWEEN MAIN SCREEN AND PIP SCREEN
Press [Yellow] button to switch between Main Screen and PIP Screen. The PIP channel
shows on the main screen, and vice versa.
• TO SEE RECORDING PIP
Press [PIP] button again to watch recordings in PIP window. You can change the
recording by pressing [Yellow] or [Blue] button.
• TO CLOSE PIP WINDOW
Press [PIP] button again to close PIP window.
✍ Note>>>
PIP is available only in live mode.
Press [Blue] button to switch between screen and teletext.
✍ Note>>>
Teletext is available only when service provider sends teletext information.
28
29
CHAPTER
7>>
PLAYING MODE
Playing mode is when you watch recorded program. Basic playback control features are
available: Stop, Pause, Rewind, Fast Forward Playback and Slow Motion Playback. And you
can use bookmark to play recordings.
PLAYBACK CONTROL
• PLAY INDICATOR
• TO REWIND
Press [REW] button to rewind toward the start of the recording. You can control playback
speed by pressing [REW] button repeatedly. Keep pressing button to go faster: x2, x4, x6, x8,
x16 and x24.
• TO FAST FORWARD
Normal Playback
Press [FF] button to fast forward toward the end of the recording. You can control
playback speed by pressing [FF] button repeatedly. Keep pressing button to go faster: x2, x4,
x8, x16 and x24.
Rewind Playback
• TO PAUSE
Fast Forward Playback
Press [Pause] button to pause playback.
Slow Motion Playback
• TO PLAY SLOW-MOTION
Pause
Press [Slow] button to slow motion playback. You can control playback speed by pressing
[Slow] button again. Keep pressing button to go slower: x1, x2, x3, x4, x5, x6 and x7.
Simple Time Line Guide
• TO DO NORMAL PLAYBACK
• TO SEE TIME SLIDER
Press [OK] button to see time slider. The play head
indicates which point in the recording currently is played.
Start Recording Time is shown on the left side and End
Recording Time is shown on the right side. The Bookmark
marker appears above timeline if you add bookmark on
the recording. Press [OK] button again to hide time slider.
Press [Play] button to do normal playback. You can resume normal playback.
• TO STOP PLAYBACK
Press [Stop] button to stop playback; then leave the Playing mode; then go back to the
previous mode before entering Playing mode.
• TO JUMP FORWARD AND BACKWARD
Press [Jump-] button to jump back 30 seconds from current position. Press [Jump+] button
to jump forward 30 seconds at a time.
• TO SEE RECORDING IN PROGRESS
Press [Red] button to see channels being recorded, and If there is recording in progress,
Recording Channel List appears. Select a channel in the list, and press [OK] button; then
channel is changed to the selected channel.
• TO JUMP FORWARD AND BACKWARD BY 10%OF RECORDED DURATION
Press [Yellow] button to jump backward, and Press [Blue] button to play forward. Current
position appears in the left side above time slider.
✍ Note>>>
When recording duration is short, you can jump to the position at 50% of the recorded duration.
30
31
CHAPTER
BOOKMARK
8>>
MAIN MENU
The Main Menu window appears by pressing [Menu] button when you watch a live
program.
You can set bookmark when watching recorded program. Using bookmark, you can jump
to the position quickly and easily using bookmark function. When time slider appears, you
can see bookmark position above the time line.
• TO ADD BOOKMARK
Press [Bookmark] button to add bookmark while watching recorded program in playing
mode. Markers show the bookmark position in the recorded program.
• TO SEE BOOKMARK LIST
Press [Green] button to call up Bookmark List Window. Thumbnails of scene are arranged
by time order; you can navigate bookmark list by pressing [Right Arrow] button or [Left
Arrow] button. Press [Menu] button or [Exit] button to close the window; then go back to the
main screen.
• CHANNEL GUIDE
You can browse channels by sorting and listing in various ways: numeric ordering,
alphabetical ordering, ordering by satellite and so on. You can list channels by selecting
favorite group and by selecting satellite. You can switch between TV channel list and radio
channel list. And also you can get detail information about a channel.
For more information, see “Channel Guide” on page 35.
• ORGANIZE CHANNELS
You can edit TV and Radio channels: renaming, locking, unlocking, rearranging, skipping
and deleting channel. And you can edit TV and Radio favorites: creating, renaming and
deleting. And you can manage your favorite channels: adding and removing the selected
channel to your favorite list.
• TO DELETE BOOKMARK IN RECORDED PROGRAM
In Bookmark List Window, you can delete the highlighted bookmark thumbnail by
pressing [Red] button. You can delete all the bookmarks in the recorded program by pressing
[Green] button.
• TO START PLAYBACK AT THE BOOKMARK
In Bookmark List Window, press [OK] button to start playback at the selected bookmark
position.
• TO START PLAYBACK AT EACH BOOKMARK
Press [SAT] button in the Play mode; then start playback at each bookmark in the
recorded program.
For more information, see “Organize Channels” on page 36.
• PROGRAM GUIDE
You can see the TV guide for today with EPG (Electronic program Guide). Also, you can
see the program schedule for another day and channel. You can see more detail information
about the program.
For more information, see “Program Guide” on page 39.
• SYSTEM SETUP
You can set up general system features: TV Screen, Time, CI (Common Interface),
Firmware, Hard Drive and USB Device.
For more information, see “System Setup” on page 41.
• INSTALLATION
You can use installation features to get signal from satellite: tuner setup and searching
channel. You can set up motorized antenna (DiSEqC 1.2/USALS). And you can manage
satellite and transponder information.
For more information, see “Installation” on page 46.
32
33
CHAPTER
9>>
CHANNEL GUIDE
• USER PREFERENCE
Choose [Main Menu] >>[1 Channel Guide].
You can set up general preferences: Language, Timer, Parental Lock, Appearance and
Hard Drive Setup including Automatic Timeshift option and so on.
Press [OK] button when watching live program.
For more information, see “User Preference” on page 55.
• RECORDING LIST
You can see the list of all recordings with various sorting methods. Also you can manage
recordings: previewing, deleting, renaming, locking and unlocking. And video editing is
available: copying, cutting and merging.
For more information, see “Recording List” on page 59.
• REMINDER LIST
You can make recording reservation by creating reminder. If there is conflict, conflict
correction dialog will help you to resolve the conflict.
For more information, see “Reminder List” on page 63.
• MULTIMEDIA/GAMES
You can enjoy multimedia and entertainment functions: music player, photo album and
games.
For more information, see “Multimedia/Games” on page 65.
• TO LIST CHANNELS BY SATELLITE
Press [SAT] button; then select satellite.
• TO LIST CHANNELS BY FAVORITE GROUP
Press [FAV] button; then select favorite.
• TO LIST CHANNELS BY ALPHABET GROUPS
Press [Red] button; then select the first character of channel name.
• TO LIST CHANNELS BY BOUQUET GROUP
Press [Green] button; then select bouquet.
• TO LIST CHANNELS BY FTA AND CAS GROUPS
Press [Blue] button; then select FTA or CAS.
• TO ARRANGE CHANNELS IN THE LIST
Press [Yellow] button; then select sorting method.
Sorting methods are listed below:
Numeric ordering of channel number
Alphabetical ordering of channel name:From A to Z
Reverse Alphabetical ordering of channel name: From Z to A
Ordering of CA (Conditional Access)system name: From FTA to CI
Reverse ordering of CA system name: From CI to FTA
Ordering of satellite name
• TO SEE CHANNEL INFORMATION
Press [Info] button. Channel information appears: Satellite name, TP frequency, TP symbol
rate, TP Polarization, Audio PID, Video PID and program number.
• TO SWITCH BETWEEN TV AND RADIO
Press [TV/Radio] button.
✍ Note>>>
During recording, only available channels appear in Channel Guide Window: channels have no conflict with
recorded channel. When recording goes on, tuner being used appears in the bottom of the list.
34
35
CHAPTER
10>>
ORGANIZE CHANNEL
Choose [Main Menu] >>[2 Organize Channel].
✍ Important>>>
By default,this feature is protected. Default password is 0000. Choose [Main Menu] > [6 User Reference] >[3
Appearance Setup]; then you can change this option.
✍ Note>>>
During recording, Organize Channel feature is not available. You should stop recording first.
USING EDIT CHANNEL
Choose [Main Menu] >>[2 Organize Channels] >>[1 Edit TV Channels].
✍ Note>>>
“2 Edit Radio Channel” works same as ”1 Edit TV Channel”.
• TO CHANGE CHANNEL NAME
Choose [Main Menu]>[2 Organize Channels]>[1 Edit TV Channels] >[2 Rename
Channels]. You can change channel name. Select a channel in the list; then press [OK ]
button. Navigate screen keyboard with arrow keys; select character you want, and then press
[OK] button; then the selected character is typed in text field. After typing new name, select
“Save” in screen keyboard and press [OK] button. Press [Red] button to switch input mode:
Capital Letters, Small Letters, Number and Special Letters. Press [Green] button to move
cursor left. Press [Yellow] button to move cursor right. Press [Blue] to delete a character.
• TO REARRANGE CHANNEL
Choose [Main Menu]>[2 Organize Channels]>[1 Edit TV Channels]>[3 Rearrange
Channels]. You can change the position of channel in the list. Select a channel in the
list;then press [OK] button. If small arrow icon appears beside item; then change position by
pressing [Up Arrow] button or [Down Arrow] button. Set the position by pressing [OK]
button again. Press [Menu] button or [Exit] button to save the result.
• TO HIDE CHANNEL
Choose [Main Menu] >[2 Organize Channels]>[1 Edit TV Channels] >[4 Skip Channels].
You can hide channels; make invisible in the list. Select a channel in the list; then press [OK]
button. The channel name is dimmed. To make it visible, select dimmed channel, and press
[OK] button again. Press [Menu] button or [Exit] button to save.
• TO LOCK AND UNLOCK CHANNEL
Choose [Main Menu]>[2 Organize Channels]>[1 Edit TV Channels] >[1 Lock Channels].
Select channel to protect; then press [OK] button. If you lock the channel, password is
needed when you try to watch it; you prevent children from watching it. If you press [OK]
button again, protection is canceled.
For more information about password management, see page 56.
• TO DELETE CHANNEL
Choose [Main Menu]>[2 Organize Channels]>[1 Edit TV Channels] >[5 Delete Channels].
Select a channel in the list; then press [OK] button. The channel is marked by red line. Press
[Red] button to select all the channels in the list. To cancel, press [Red] button again. Press
[Menu] button or [Exit] button to save.
✍ Note>>>
You can sort and list channels: by satellite, by favorite and by alphabetical order.
• TO ORDER LIST BY SATELLITE
Press [Green] button; then select a satellite in popup window.
• TO ORDER LIST BY FAVORITE
Press [Yellow] button; then select a favorite in popup window.
• TO SORT LIST
Press [Blue] button; then select a sorting method; numeric order, alphabetical order (From
A to Z) and reverse alphabetical order (From Z to A).
36
37
CHAPTER
USING EDIT FAVORITE GROUP
Choose [Main Menu] >>[2 Organize Channels] >>[3 Edit TV Favorites].
✍ Note>>>
“4 Edit Radio Favorites” works same as “3 Edit Radio Favorites”.
11>>
PROGRAM GUIDE
Choose [Main Menu] >>[3 Program Guide]. Press [EPG] button in live mode.
You can see program guide for the channel you watch. And you can record program or
make recording reservation. The EPG provides detail information about programs.
✍ Note>>>
EPG can be different depending on the satellite service provider.
✍ Important>>>
It is not available to group TV and Radio channels together in the
same favorite group. You should separate TV favorite group and Radio
favorite group.
• TO CREATE FAVORITE GROUP
Choose [Main Menu]>[2 Organize Channels]>[3 Edit TV Favorites]>[1 Create Favorite
List]; then screen keyboard appears.
✍ Note>>>
You can create favorite groups up to 8.
• TO CHANGE FAVORITE GROUP NAME
Choose [Main Menu] >>[2 Organize Channels] >>[3 Edit TV Favorites] >>[2 Rename
Favorite List].
Select a favorite group in the list, and press [OK] button; then screen keyboard appears.
You can change favorite group name using screen keyboard.
• TO DELETE FAVORITE GROUP
• TO SEE PROGRAM GUIDE OF OTHER CHANNEL
Press [Right Arrow] button or [Left Arrow] button.
• TO RESERVE RECORDING OR WATCHING PROGRAM
Select a program in the list; then press [OK] button to make reservation to record the
program. You can just reserve to watch the program by pressing [OK] button again.
✍ Note>>>
If PVR detects conflict with other existing reservations or recordings,
Conflict Management Dialog helps you to resolve the problem.
Choose [Main Menu] >>[2 Organize Channels] >>[3 Edit TV Favorites] >>[3 Delete
Favorite List].
Select a favorite group in the list; then press [OK] button.
• TO ADD A CHANNEL TO FAVORITE GROUP
Choose [Main Menu]>[2 Organize Channels]>[3 Edit TV Favorites]>[4 Add/Remove
Favorite List]; then select Favorite group. If no favorite group exists, you should create new
group first. Select a channel in the list; then press [OK ].The channel is added to the rightside list titled “Channels In Favorite”. You can switch focus between the lists by pressing
[Red] button.
• TO SEE PROGRAM GUIDE OF OTHER DAY
• TO REMOVE A CHANNEL FROM FAVORITE GROUP
• TO FIND PROGRAM
Choose [Main Menu]>[2 Organize Channels]>[3 Edit TV Favorites]>[4 Add/Remove
Favorite List]; then select Favorite group. Press [Red] button to switch focus to the list on the
right side.
You can find a program by program finder. EPG is cached at the PVR and you can find
the program very fast from the huge amount of EPG data. Press [Green] button to see
program finder window.
Press [Yellow] button to see the programs of a day after. The available number of date
depends on the service provider. You can keep changing the day by pressing [Yellow]
button.
Select a channel in the list; press [OK ] button. The channel is removed from the list on
the right side. Press [Menu] button or [Exit] button to save.
38
39
CHAPTER
• TO CHANGE CATEGORY IN PROGRAM FINDER WINDOW
In program finder, you can search by composition of three categories: Date, Provider and
Genre.
_Press [Red] button to select category.
_Press [Green] button to go back.
_Press [Yellow] button to go forward.
12>>
SYSTEM SETUP
Choose [Main Menu]>[4 System Setup]. You can set up general PVR system features: TV
Screen, Time, CI, Firmware, Hard Drive Format and USB Device.
SETTING UP TV
Choose [Main Menu] >[4 System Setup] >[1 TV Setting]. The PVR has many A/V Outputs.
Control this menu properly according to external components connected to the PVR.
_Press [Blue] button to jump to the next program by
one hour.
You can book recording and tune program by pressing
[OK] button. The operation is same as in the previous EPG
list window.
• TO SEE MORE INFORMATION ABOUT PROGRAM
Select a program in the list; then press [Info] button.
• TO SET UP AUDIO VIDEO OUTPUT
Choose [1 AV Settings] >>[1 Video Output].
Select the video mode for the video output; CVBS, SVideo, RGB and YPbPr.
• TO SET UP AUDIO OUTPUT
• TO SEE PROGRAM GUIDE IN TABLE STRUCTURE
Choose [1 AV Settings] >>[2 Audio Output].
Press [Red] button to see Program Guide in Grid. You
can browse channel with more ease.
Press [OPT] button in live mode.
Select a program in the table; then press [OK] button to
record instantly or to make recording reservation.
Select the audio mode for audio output; Stereo, Left Mono and Right Mono.
• TO CHANGE ASPECT RATIO
Choose [1 AV Settings] >[3 Aspect Ratio]. Select an aspect ratio of video output: “4:3“
and “16:9”.
TV standard is “4:3” and HDTV standard is “16:9”.
• TO CHANGE DISPLAY FORMAT
Choose [1 AV Settings] >>[4 Display Format].
It is only available when aspect ratio is “4:3”: Select the display format: Pan-and-Scan
and Letterbox.
• TO CHANGE SCREEN POSITION
Choose [3 OSD Position Setup].
Set screen position by pressing [arrow] keys.
• TO CHANGE TV STANDARD
Choose [4 TV Settings]. Select TV standard: PAL and NTSC.
40
41
SETTING UP UHF MODULATOR
Choose [Main Menu] >>[4 System Setup] >>[2 UHF Setting].
Press [UHF] button in live mode.
• TO SET CURRENT TIME IN MANUAL MODE
Choose [1 Time Mode]; then select Manual.
Choose [2 Set Local Time]; then select a time zone; GMT offset of the local area. Set year,
month and day with [Right Arrow] and [Left Arrow] button.
Choose [4 Year]; then select year.
Choose [5 Month]; then select month.
Choose [6 Day]; then select day.
Choose [7 Current Time]; then enter current time by pressing numerical buttons.
• TO CHANGE CHANNEL
Choose [2 UHF Setting] >[1 UHF Channel].
Set UHF Channel: From 21 to 69, Default channel is 36.
• TO CHANGE UHF STANDARD
Choose [2 UHF Setting] >>[2 UHF Standard].
Select UHF Standard; PAL G, PAL I and PAL K.
• TO SET CURRENT TIME IN AUTOMATIC MODE
Choose [1 Time Mode]; then select Manual.
Choose [2 Set Local Time]; then select a time zone; GMT offset of the local area.
Choose [4 Time Setup Channel]; then select the channel you want to receive time
information.
Choose [7 Setup Time Now]; then PVR try to get time information from the selected
channel. The current time appears in [5 Current Date] and [6 Current Time].
• TO SET SUMMER TIME
SETTING UP TIME
Choose [Main Menu] >>[4 System Setup] >>[2 Time Setting].
✍ Note>>>
During recording, this feature is unavailable. You should stop the
recording first.
Choose [3 Summer Time]; then select Enable.
CI (COMMON INTERFACE) MODULES
Choose [Main Menu] >>[4 System Setup] >>[3 Common Interface].
Select a CAM (Conditional Access Module) in the list ; then press [OK] button to see
detail information of installed CI module.
• ABOUT TIME SETTING MODE
You can set current time in two ways: manual and automatic. In manual mode, you
should set up time manually. While power cord is plugged, PVR keeps the current time. But
after unplugging it, you should set the current time again. In automatic mode, you can
resolve this by automatically getting time information from a channel. You should select the
channel for automatic time setting.
✍ Note>>>
In manual mode, “Time Setup” window will appear when you turn on PVR. In automatic mode, the timereceiving channel will be tuned first when you turn on PVR.
42
PVR MANAGEMENT
Choose [Main Menu] >>[4 System Setup] >>[4 STB Management]. You can protect this
feature by password.
For more information, see “User preference” on page 56.
✍ Note>>>
It is not available when recording is in progress. You should stop recording first before using this feature.
43
• TO SEE SOFTWARE VERSION
Choose [1 System Information]; then press [OK] button.
ERASING DATA
Choose [Main Menu] >>[4 System Setup] >>[5 HDD Management].
• TO RETURN PVR TO FACTORY DEFAULT
Choose [2 Factory Default]; then press [OK] button. You can return your PVR to factory
default state.
✍ Warning>>>
All the data and configurations will be lost: channel and satellite configuration including favorite group. And
Easy Installation will appear to help installation. Data in HDD such as recording, MP3 and Jpeg will not be lost until
you format it.
• TO SEND FIRMWARE TO OTHER PVR
Connect your PVR and the target PVR via serial cable (RS-232 ). Turn on the target PVR.
• TO ERASE ALL RECORDINGS
Choose [1 Format Recording]; then press [OK] button.
Choose [3 Transfer Firmware]; then press [OK] button.
For more Information, see “Connecting to other PVR using Serial Cable” on page 16.
✍ Warning>>>
You shouldn’t disconnect while data is being transferred.
• TO SEND CHANNEL DATA TO OTHER PVR
Connect your PVR to target PVR via serial cable (RS–232). Turn on the target PVR.
Choose `4 Transfer Channel Data'; then press [OK] button.
For more Information, see “Connecting to other PVR using Serial Cable” on page 16.
✍ Warning>>>
You shouldn't disconnect while data is being transferred.
• TO ERASE ALL MP3
Choose [2 Format MP3]; then press [OK ] button.
• TO ERASE ALL JPEG
Choose [3 Format JPEG]; then press [OK] button.
✍ Warning>>>
It is impossible to restore lost data. You can back up data to PC using USB connection.
CONNECTED USB DEVICES
Choose [Main Menu] >>[4 System Setup] >>[6 USB Devices]. You can see the list of USB
devices connected to your PVR.
• TO RECEIVE SATCO-DX CHANNEL DATA FROM PC
Connect your PVR and PC via serial cable (RS-232 ). Open Satco-DX software in PC. You
can search channel with Satco-DX software. Choose [5 Satco-DX]; then press [OK] button.
Open Programming Wizard in Satco-DX software, and click program receiver button.
For more Information, see “Connecting to PC using Serial Cable” on page 15.
✍ Note>>>
You should set Satco-DX File Format to “Satco-DX Industry Standard Protocol”, and set transfer baud rate of
COM port to 115,200.
✍ Warning>>>
You shouldn’t disconnect while data is being transferred.
44
45
CHAPTER
13>>
INSTALLATION
Choose [Main Menu] >>[5 Installation]. You can protect this feature by password.
SETTING UP ANTENNA
For more information, see “User preference” on page 56.
1 SELECT TUNER TO SET UP
Choose [1 Antenna Number].
Select antenna number; one tuner supports up to 32 satellites.
✍ Note>>>
The antenna number doesn’t have a practical meaning.
2 SELECT SATELLITE NAME
Choose [2 Satellite Name].
USING EASY INSTALLATION
Select a satellite by pressing [Right Arrow] button or [Left Arrow] button. Press [OK]
button; then satellite list appears. The list is put in alphabetical order. Scroll the list and
select a satellite.
Easy Installation is a step-by-step procedure for user convenience. At the first time your
PVR gets powered on after purchasing, easy installation starts automatically. You can use
easy installation later to manage your PVR. For more information about easy installation, see
“Getting Started“ on page 17.
✍ Note>>>
SETTING UP ANTENNA MODE
3 SET UP LNB
Choose [Main Menu] >>[5 Installation] >>[2 Antenna Setup] >>[1 Connection Type].
If you cannot find the satellite you want, you should create new satellite information. For more information, see
“To Create New Satellite Information” on page 53.
Choose [3 LNB Frequency].
Your PVR has two tuners; two LNB input ports. You can connect both tuners to antennas
independently: Separated Connection.
Press [Right Arrow] button or [Left Arrow] button to select LNB type and LNB Frequency:
5150, 9750, 10750,11300 and Universal. Press [OK]button; then LNB setup window
appears. You can set up detail LNB options: LNB type, LNB low frequency and LNB high
frequency.
• SINGLE MODE
✍ Important>>>
• DUAL MODE
In single mode, tuner 1 is connected antenna, and tuner 2 input port is connected to tuner
1 output port: Loop-through connection.
For more information about antenna connection, see “Connecting to the satellite antenna”
on page 11.
• TO SELECT TUNER 1 TO SET UP
Choose [Main Menu] >>[5 Installation] >>[2 Antenna Setup] >>[2 Tuner 1 Setup].
• TO SELECT TUNER 2 TO SET UP
Choose [Main Menu] >>[5 Installation] >>[2 Antenna Setup] >>[2 Tuner 2 Setup].
Your PVR suggests a proper LNB frequency by analyzing the satellite you choose.
4 22KHZ CONTROL
Choose [4 22 kHz Control]. Select “On” or “Off”.
5 SELECT DISEQC INPUT SWITCH
Choose [5 DiSEqC Switch Control].
Select a DiSEqC Switch options; Disable, 1 of 4, 2 of 4, 3 of 4, 4 of 4, mini A and mini B.
Your PVR is DiSEqC compatible, so you can connect more antennas using DiSEqC switching
device. If PVR receives signal from satellite, Signal Strength and Signal Quality will show
below.
✍ Note>>>
“Tuner 2 Setup” works exactly the same as “Tuner 1 Setup”.
46
47
6 SELECT TRANSPONDER
Choose [6 Transponder].
Select a transponder in the satellite by pressing [Right Arrow] or [Left Arrow] button. If
PVR receives signal from satellite, you can watch the channel provided in the transponder.
✍ Note>>>
If you cannot find the transponder you want, you should create new transponder information.
For more information, see “To Create New Transponder Information” on page 54.
• TO SAVE CURRENT ANTENNA SETUP
Choose [7 Save]; then press [OK] button.
• TO DELETE SATELLITE
Choose [1 Antenna Number] and select satellite you want to delete. Press [Yellow] button
to delete.
USING CHANNEL SEARCH
Choose [Main Menu] >>[5 Installation] >>[2 Channel Search].
There are three searching modes: Auto, Manual and Advanced. By default, channel
searching mode is “Auto”. PVR scan all the transponders in the satellite in Auto mode. In
Manual mode, you can select a transponder to scan. In Advanced mode, you can scan only
one channel by specifying the satellite information: Transponder frequency, Polarization,
Symbol Rate, Video PID, Audio PID and PCR PID.
• TO SELECT SATELLITE TO SEARCH CHANNEL
Choose [Main Menu] >>[5 Installation] >>[2 Channel Search] >>[1 Select Satellite].
Select satellite by pressing [Right Arrow] button or [Left Arrow] button.
• AUTOMATIC CHANNEL SEARCH
Choose [2 Automatic Search]; then press [OK] button. You can set up channel searching
options.
✍ Note>>>
If you Don’t save, the deleted satellite will be recovered.
• NETWORK SEARCH
Your PVR scan transponder information in signal when searching channels. If new
transponder is found, PVR adds it automatically.
✍ Note>>>
If you disable “Network Search”, channel searching will be little bit faster.
• FTA OR CA SEARCH
Only FTA channels or CA Channels are searched.
• TO START SEARCH
Choose [3 Start Search]; then press [OK] button.
You can see searched channels; TV and Radio, a summary of the founded channels will
be displayed when the scanning is completed.
• TO CANCEL CHANNEL SEARCHING
If you want to cancel searching in progress, press [Menu] button or [Exit]button. Select
[OK] in confirm dialog;then press [OK] button.
48
49
MANUAL CHANNEL SEARCH
Choose [3 Manual Search]; then press [OK ] button.
USING MOTORIZED ANTENNA CONTROL
Choose [Main Menu] >>[5 Installation] >>[3 Motorized Antenna].
• TO SET UP MOTORIZED ANTENNA WITH DISEQC 1.2
a Select a tuner that is connected to the motorized antenna you want to set up.
b Choose [Select Tuner 1]; then press [OK] button. Or Choose [Select Tuner 2]; then
press [OK] button.
c Choose [1 Satellite Select] and select the satellite in the tuner..
d Choose [2 Select Transponder] and select the TP in the satellite.
• TO SEARCH CHANNELS IN THE TRANSPONDER (TP)
e Choose [3 Motorized Antenna Control] and select [ DiSEqC 1.2].
Choose [1 Select Transponder]. Select a TP in the satellite by pressing [Right Arrow]
button or [Left Arrow] button. TP information will show below; TP frequency, polarization
and symbol rate. You can also see the signal quality of selected TP.
f Choose [4 DiSEqC 1.2 Mode] and select the mode: “User”and “Installer”.
✍ Note>>>
If you can find TP you want, you should create new TP. For more information, see page 54.
ADVANCED CHANNEL SEARCH
Choose [4 Advanced Search]; then press [OK] button.
• USER MODE
a Select “User” in [4 DiSEqC 1.2 Mode].
b Choose [5 Motor Control] and select actions: “GoTo” and “Store”.
c Select a “GoTo” to control motorized antenna.
d Choose [6 Movement] to find the antenna position with the best signal quality.
e Select the number of step between 1 and 60, and direction; East (E)and West (W).
Select 0 is to stop the motor.
f Choose [7 Action] and press [OK] button to move the antenna. If you find the
position, choose [5 Motor Control]; then select “Store”.
To search specific channel, you should know detail information about channel and
transponder; Video PID, Audio PID, PCR PID, Transponder Frequency, Transponder
Polarization and Symbol Rate.
You should enter each value correctly by pressing numerical buttons.
✍ Note>>>
You should enter each value without exception.
g And choose [7 Action] and press [OK] button to store current antenna position.
• INSTALLER MODE
a Select “Installer” in [4 DiSEqC 1.2 Mode].
b Choose [5 Motor Control] and select actions; “Go To East”, “Go To West”, “Stop”,
“Reset”, “Set Limit East”, “Set Limit West”, “Limits Off”and “Store”.
c Choose [6 Action] and press [OK] button.
The actions are listed below:
a “Go To East” and “Go To West”- Keep driving the antenna until you press [OK ] button
50
51
again.
b “Reset “-Reset the antenna position.
c “Set Limit East(E)” and “Set Limit West(W)”- Set current position to the maximum step
of the direction.
USING EDIT SATELLITE
Choose [Main Menu] >>[5 Installation] >>[4 Edit Satellite].
d “Limit Off”-Reset the limits.
If you find the position, choose [5 Motor Control] and select “Store”; then choose [7
Action] and press [OK] button to store the current antenna position.
• TO SET UP MOTORIZED ANTENNA WITH DISEQC 1.3 (USALS )
a Select a tuner that is connected to the motorized antenna you want to set up.
b Choose [1 Satellite Select] and select the satellite in the tuner.
• TO CREATE NEW SATELLITE INFORMATION
c Choose [2 Select Transponder] and select the transponder in the satellite.
d Choose [3 Motorized Antenna Control] and select [DiSEqC 1.3 (USALS)].
Choose [6 New Satellite]; then press [OK] button. Enter new satellite name in screen
keyboard.
e Enter your local latitude and longitude in [4 My Latitude] and [5 My Longitude].
✍ Note>>>
f Choose [7 Go To the Position] and press [OK] button to drive the motorized antenna.
You can create satellite up to 200 satellites. Newly created satellite has no transponder. You should add new
transponder for the satellite.
• TO SET UP LONGITUDE OF SATELLITE
Choose [5 Edit Satellite Longitude].
Enter longitude number by pressing numerical buttons; then select East (E) or West (W).
• TO DELETE SATELLITE INFORMATION
Choose [7 Delete Satellite]; then press [OK] button.
✍ Warning>>>
If you delete satellite, all the transponders and channels in the satellite will be deleted too.
52
53
CHAPTER
USING EDIT TRANSPONDER
Choose [Main Menu] >>[5 Installation] >>[5 Edit Transponder].
14>>
USER PREFERENCE
Choose [Main Menu] >>[5 User Preferences].
You can set up general PVR preferences: Language, Timer, Parental Lock, Screen
Appearance and PVR recording options like Timeshift.
LANGUAGE
• TO SET UP LANGUAGE
Choose [1 Language Setup]>[1 OSD Language]; then
select language: English, German, Turkish and Russian. By
default, menu language is English.
• TO CREATE NEW TRANSPONDER INFORMATION
Choose [1 Satellite Name] to select satellite you want to add new transponder to.
Choose [5 New Transponder]; then press [OK] button.
Enter new transponder information: Transponder Frequency, Polarization and Symbol
Rate.
✍ Note>>>
You can create new transponder up to 3,000.
• TO DELETE TP INFORMATION
Choose [6 Delete Transponder]; then press [OK] button.
✍ Note>>>
• TO SET UP SUBTITLE LANGUAGE
Choose [1 Language Setup]>[2 Subtitle Language]; then
select language for default subtitle language: English,
French, Deutsch, Italian, Spanish, Arabic, Greek, Turkish,
Danish, Swedish, Norwegian, Dutch, Russian and Korean.
• TO SET UP AUDIO LANGUAGE
Choose [1 Language Setup]>>[3 Audio Language]; then select language for default audio
language.
• TO SET UP SI (EVENT)LANGUAGE
Choose [1 Language Setup]>[4 SI(Event)Language]; then select language for default event
language.
If you delete a transponder, channels in the transponder will be deleted too.
TIMER
• TO SET UP SLEEP TIMER
Choose [2 Timer Setup] >>[1 Sleep Timer Control].
You can set timer to make PVR sleep: every 15 minutes for 6 hours later. When you set
timer, “Sleep Time” appears below.
✍ Note>>>
It does not affect any recording reservations. PVR can start recording in sleep mode.
54
55
PARENTAL LOCK
PVR SETUP
• TO PROTECT ITEMS BY PASSWORD
• TO ENABLE AND DISABLE AUTOMATIC TIMESHIFT OPTION
Choose [3 Parental Control]. You can protect features by
password: Receiver, Age Rating, Installation and STB
Management.
Choose [4 PVR Setup] >[1 Automatic Timeshift]; then
select “On” to turn on Automatic Timeshift. If you enable
Automatic Timeshift, you can do trick play whenever you
watch a live program. If you turn off Automatic Timeshift,
you should press [Pause] button to enter timeshift mode
when watching live program. But you can reduce the
power consumption.
When “Receiver Lock” is turned on, you should enter
password to start up your PVR.
When “Installation Lock” is turned on, you should enter
password to start “Installation” in menu: when you choose
“Main Menu” >> “5 Installation”.
When “STB Management Lock” is turned on, you should enter password to start “STB
Management” in menu: when you choose [Main Menu] >>[4 System setup] >>[4 STB
Management].
• TO CHANGE PASSWORD
Choose [3 Parental Control] >>[5 Change PIN]; then press [OK] button.
Enter new password by pressing numerical buttons and select OK in confirm dialog.
• TO SET UP HARD DRIVE SIZE FOR TIMESHIFT
Choose [4 PVR Setup] >[2 Timeshift Buffer Size]; then select hard drive size from 1 to 8
GB. One GB hard drive can handle the recording for a half hour.
✍ Note>>>
If Timeshift Recording buffer grows over the limit, PVR overwrites the previous Timeshifted Recording.
• TO SET UP HARD DRIVE MANAGEMENT OPTION
Choose [4 PVR Setup] >>[3 DISK Management]; then select “Manual” and “Automatic”.
APPEARANCE
If you select “Automatic”, when hard disk drive becomes full, PVR erases old recordings
with the least priority.
• TO SET DURATION FOR SHOWING CHANNEL
INFORMATION
If you select “Manual”, when the space of hard disk gets full, PVR shows a warning
message, and stops recording.
Choose [4 Appearance Setup] >[1 InfoBox Duration];
then select how long channel Information will appear: 5
sec, 8 sec, 10 sec, 12 sec, 15 sec and Don’t show.
• TO SHOW OR HIDE RECORDING DIALOG WHEN STARTING RECORDING
For more information about Channel Information, see
“Channel Information Box” on page 23.
If you select “Enable”, recording dialog appears when you start recording in live mode.
You can set up current recording options:starting time, duration and decryption.
• TO SET DURATION FOR SHOWING PLAY INDICATOR
Choose [4 Appearance Setup] >[2 Play Indicator Duration]; then select how long Play
Indicator will appears: 5 sec, 8 sec, 10 sec, 12 sec, 15 sec and Don’t show. Play indicator is
time slider that shows you current playing position in Play mode.
For more Information, see “Play mode” on page 30.
Choose [4 PVR Setup] >>[4 Prompt On Recording] and select “Enable” and “Disable”.
For more information, see “Instant Recording” on page 26.
If you select “Disable”, you can record a program instantly. By default, PVR keeps
recording program until you stop recording by pressing [Stop] button or hard drive get full.
• TO SAVE OPTIONS
Choose [5 Save]; and press [OK] button.
• TO SET VOLUME BAR
Choose [4 Appearance Setup]>[3 Volume Bar]; then select “On” to show volume control
bar, or otherwise select “Off”.
56
57
CHAPTER
EPG SETUP
• TO ENABLE EPG CACHING
15>>
RECORDING LIST
Choose [Main Menu] >>[7 Recording List].
Press [Recording] button when you are watching a live TV program. You can browse and
find recorded programs.
Choose [1 EPG Caching]; then select “On” to enable EPG caching. EPG data from service
provider will be automatically cached into the PVR hard disc. So, you do not need to wait
for EPG next time.
• TO GRABBING EPG
Choose [2 EPG Grabbing]; then select “On” to enable EPG Grabbing. You can set up time
and channel for grabbing EPG. PVR will get EPG data everyday at a defined time
automatically.
• TO GRABBING EPG INSTANTLY
Choose [5 Grab EPG Now]; then press [OK] button. If you don’t select channel to grab,
Current channel’s EPG will be updated.
✍ Note>>>
Grabbing EPG for many channels is a heavy process taking long time.
We suggest you to set up EPG grabbing time at a time when you are not
using PVR, as 12:00 PM.
• TO WATCH RECORDED PROGRAM
Select the program in the list by pressing [Right Arrow] and [Left Arrow] key. Press [OK]
button to watch the recording.
• TO WATCH RECORDED PROGRAM IN PREVIEW WINDOW
Select the program in the list by pressing [Right Arrow] and [Left Arrow] key. Press [PLAY]
button to watch the recording in preview window.
• TO DO BASIC PLAYBACK IN PREVIEW WINDOW
When you watch a program in preview, playback control is available.
Press [REW] to rewind, Press [FF] to fast forward playback. Press [SLOW] to slow motion
playback and press [PAUSE] to pause.
• TO SORT RECORDING LIST
Press [Green] button to change sorting method; sorting by channel name, recorded date
and recorded duration. Press [Yellow] button to switch direction between UP and DOWN:
in order and in reverse order.
• TO SEE MORE INFORMATION ABOUT PROGRAM
Press [Info] button to see more information about program. To close, press [Info] button
again.
• TO SWITCH BETWEEN TV AND RADIO RECORDINGS.
Press [TV/Radio] button to switch from TV Recording to Radio Recording or vice versa.
• TO MANAGE RECORDINGS
Press [Red] button to manage recordings; Delete, Rename, Copy, Cut, Merge and Lock.
58
59
EDIT RECORDING
Press [Red] to manage recordings. You can manage recorded video; deleting, renaming,
copying, cutting, merging and protecting. You can change the type of recorded program:
Erasable and permanent. Sorting methods are provided as same as “Recording List”: by
channel number, channel name, recorded time and duration.
First, you should select action to use by pressing [Red] button. Selected action is
highlighted on top of the window.
2 Select the spot to end copying
Press [Red] button to copy to the arrow in timeline. Press [Green] to copy to end of
recorded video. The position is marked with red, and the area to be copied is determined.
3 Copy or Cancel
Press [Red] button to do copy. Copy progress dialog appears, and copied recording gets
new name with prefix "C:"
Press [Green] button to cancel copying; then you should start again.
✍ Note>>>
You can do trick play: Fast-forward, Rewind, Pause and Slow Motion playback by pressing video control
buttons.
To Quit Copying Area Selection
Press [Stop] to leave.
• TO CUT RECORDED VIDEO
• TO DELETE RECORDED VIDEO
Select action [Cut] by pressing [Red]button. Select a program in the list; then press [OK]
button.
Select a program in the list; then press [OK] button. The selected program is marked red.
The recorded video starts to play with timeline indicator. You should set the area to cut
away by pressing [Red] or [Green] button.
To delete, press [Red] button; then select [OK] in confirm dialog.
1 Select the Position to Begin Erasing
Select action “Delete” by pressing [Red] button.
• TO RENAME RECORDED PROGRAM
Select action “Rename” by pressing [Red] button.
Press [Red] button to erase from the arrow in timeline. Press [Green] button to erase from
the beginning of recorded video. The position is marked green, and the area to be copied
turns into blue.
Select a program in the list; then press [OK] button. You can enter new name using screen
keyboard window, or you can change recorded video name to the name of show. By default,
channel name is set to recording name.
2 Select the Position to End Cutting
✍ Note>>>
3 Cut or Cancel
The maximum length of name character is 32. By default, program name shows in text field in screen keyboard.
When the name is long, you should delete character first to enter new name.
Press [Red] button to do erase. Press [Green] button to cancel cutting, you should start
again.
• TO COPY RECORDED VIDEO
✍ Note>>>
Select action [Copy] by pressing [Red] button. Select a program in the list; then press [OK]
button.
The recorded video starts to play with timeline indicator. You should set copying area by
pressing [Red] or [Green] button.
Press [Red] to erase to the current arrow in timeline. Press [Green] button to erase to end
of recorded video. The position is marked red, and the area to be erased is determined.
You can do trick play: Fast-forward, Rewind, Pause and Slow playback by pressing video control buttons.
To Quit Cutting Area Selection
Press [Stop] to leave.
1 Select the Position to Begin Copying
Press [Red] button to copy from the small arrow in timeline. Arrow indicates current
playing position in the recording. Press [Green] button to copy form the beginning of
recorded video. The position is marked with green, and the area to be copied turn into blue.
60
61
CHAPTER
• TO MERGE RECORDED VIDEO
Select action "Merge" by pressing [Red] button and select a program to merge. If you
select a program in the list, number appears at the left side of the selected program. Press
[Red] button to merge selected program.
16>>
REMINDER LIST
Choose [Main Menu] >>[8 Reminder List].
Press [Reminder] button when you are watching a live
program.
✍ Note>>>
Only recordings in the same channel can be merged.
• TO CHANGE RECORDING TYPE
Select action "Change Type" by pressing [Red] button and select a program to change
recording type: Permanent and Erasable. By default, recorded video is erasable. You can see
recording type by small icon on the left side;
is Erasable and
is Permanent.
• TO CREATE REMINDER
Press [Red] button to create new reminder; then
reminder window appears.
• TO LOCK RECORDED VIDEO
Select action "Lock" by pressing [Red] button. You should enter password to use this
feature; then you select a recording to lock in the list, and press [OK] button. If the program
is protected, small
appears on the left. To unlock, press [OK] button again.
Choose [1 Create Name] and select a channel you
want to reserve.
✍ Note>>>
Choose [2 Event Type] and select a reminder type:
Record and Tune.
If a recorded video is protected, you should enter password to watch, delete and merge.
If you choose “Record”, you can make a reminder for
recording the selected channel.
If you choose “Tune”, you make a reminder for watching the selected channel.
• TO SET DATA AND TIME
Choose [4 Start Date]; then select date by pressing [Right Arrow] and [Left Arrow] key.
Choose [5 Start Time]; then enter time by pressing [numerical] buttons.
• TO SET DURATION
Choose [6 Duration]; then select recording duration: every 5 minutes for 50 hour. By
default, the duration is 4 hour.
• TO RECORD TV SERIES PROGRAM
Choose [3 Frequency]; then select options: Daily,Weekly and Weekday.
If you choose “Daily”, PVR starts recording at the set time for everyday.
If you choose “Weekly”, PVR starts recording at the set time for every week.
If you choose “Weekday”, PVR starts recording at the set time for weekdays.
• REMINDER TYPE
You can see reminder type by checking small icon in the right side. Green
means
recording reservation. Green
means tuning reservation. Red “T” means
that recording is in progress: You can stop recording by pressing [Green] button.
62
63
CHAPTER
• TO DELETE REMINDER
Select a reminder in the list and press [Yellow] to delete the reminder.
17>>
MULTIMEDIA/GAMES
USING MP3 PLAYER
Choose [Main Menu] >>[9 Multimedia/Games] >>[1 MP3 Player].
• TO STOP RECORDING
Select a reminder in the list and press [Green] to delete the reminder.
RECORDING RESERVATION CONFLICT
• TO RESOLVE RESERVATION CONFLICT
If PVR detects reservation conflict, “Conflict Dialog”
appears. If you select “OK”, you can see the list of
reminders that conflict with each other.
• TO BROWSE MP3 FILES IN PVR
Press [OK] button to enter a folder, and browse mp3 files by pressing [Right Arrow] button
and [Left Arrow] button. You can scroll up and down the list; then MP3 information appears
on the right side: song title, artist, genre, encoding bit rate and so on.
Press [Green] button to increase volume and press [Red] button to decrease volume.
• TO EDIT CONFLICT
✍ Note>>>
Press [OK] button to edit conflict. You can change the
recording start time or recording duration. If conflict is
resolved, the red bar turns into white; then “Conflict
Resolved” message appears.
[VOL+] button and [VOL-] button are unavailable, because they are used to scroll the list as [Right Arrow]
button and [Left Arrow] button.
Select [OK] and press [OK] button.
• TO PLAY MUSIC INSTANTLY
Select a MP3 in the list; then press [Play] button. You can fast forward, rewind and pause
during playing MP3 file.
• TO SELECT MP3 TO ADD PLAY LIST
• USING AUTOMATIC CORRECTION
Press [Green] button to resolve conflict automatically.
• TO DELETE CONFLICT REMINDER
Select the conflict reminder in the list. Press [Red] button to delete it. If conflict is
resolved, the red bar turns into white; then “Conflict Resolved” message appears.
Select a MP3 in the list; then press [Blue] button to select MP3 to play. If you select a MP3
file, “+” icon appears at the right side of item. In MP3 player mode, you can listen only
selected MP3 files.
To cancel selection, press [Blue] button again.
✍ Note>>>
If you do not select any MP3 file, you can listen all the MP3 files in the current directory.
Select [OK] and press [OK] button.
64
65
MP3 PLAYER MODE
USING MP3 FILE OPERATION
• TO PLAY MUSIC WHILE WATCHING LIVE PROGRAM
Select a folder or a file in the list; then press [Yellow] button. In File Operation, you can
manage MP3 files as deleting, copying, moving and creating a new folder.
Select a MP3 in the list; then press [OK] button to enter MP3 player mode. You can hear
MP3 while watching a live broadcast. In this mode the audio of the selected channel is
deactivated.
Once you enter into File Operation mode by pressing [Yellow] button, you can navigate only
in the selected folder. To access other folders you need to get out of File Operation by
pressing Menu button.
✍ Note>>>
It is not available to use File Operation in root folder.
• TO SHUFFLE PLAY
Press [Blue] button; and choose “Shuffle”, and select
“On”.
• TO CREATE NEW FOLDER
Press [Red] button; then enter new folder name by using screen keyboard window.
• TO REPEAT PLAY
✍ Note>>>
In MP3 Player mode, press [Blue] button; and choose “Repeat”, and select options: On,
Current and Off. Select “On” to repeat all MP3 in the folder. Select “Current” to repeat only
current MP3.
• TO DELETE FOLDER OR FILE
Select a folder or file to delete in the list; then press [Green] button. In Confirm window,
select OK and press [OK] button.
Press [VOL+] button and [VOL-] button to control volume.
• TO SELECT MP3
Press [Up Arrow] button and [Down Arrow] button to select MP3 to listen.
Press [Jump Up] button and [Jump Down] button to select MP3 to listen.
• TO LEAVE MP3 PLAYER MODE
Press [Exit] button or [Menu] button to close MP3 Player and go back to the MP3 file list.
The maximum length of folder name character is 32.
• TO COPY FOLDER AND FILE TO DESTINATION PATH
Select a folder and file to copy; then press [Yellow] button. Focus is switched to the target
list in the right side.
Select destination folder to copy to in the target list. Press [Red] button to do copy, press
[Green] button to cancel.
• TO MOVE FOLDER AND FILE TO DESTINATION PATH
Select a folder and file to move; then press [Blue] button. Focus is switched to the target
list in the right side.
Select destination folder to move to. Press [Red] button to move, press [Green] button to
cancel.
✍ Note>>>
It is not available to move or copy file in the same folder. Make sure to select appropriate folder and file before
you begin to operate: delete, copy and move.
66
67
USING PHOTO ALBUM
Choose [Main Menu] >>[9 Multimedia/Games] >>[2 Photo Album].
• TO SET UP SLIDE SHOW
Press [Red] to set slide show.
You can choose slide effect: Normal, Scroll Up, Scroll
Down, Scroll Right, Scroll Left and Swelling.
• TO BROWSE JPEG FILES IN PVR
Press [OK] button to enter a folder, and browse JPEG files by pressing [Right Arrow]
button and [Left Arrow] button. You can scroll up and down the list; then press [OK] button
to enter the slide show mode. You can see photo in preview, when you select a JPG file in
the list.
• TO VIEW IN THUMBNAILS
You can see thumbnail list of photos by pressing [Green] button. You can browse the list
by pressing [arrow] keys. Press [OK] button to enter the slide show mode.
• TO ROTATE PHOTO IMAGE
Press [Red] button to rotate image. Image rotates 90 degree to clockwise direction when
you press [Red] button repeatedly.
You can check the result instantly when you change the
option. You can select the duration for photo transition: 3
sec, 5 sec, 7 sec and 9 sec. You can determine whether
indicator on the top-right side will show or not.
• TO WATCH A LIVE BROADCAST IN SLIDE SHOW MODE
Press [Blue] button to watch a live broadcast in PIP.
You can select channel by pressing [Up Arrow] button and [Down Arrow] button.
✍ Note>>>
If it is unavailable to watch current channel, PIP window remains as blank.
In slide show mode, you can listen audio from a live broadcast. You can control volume
by pressing [VOL+] and [VOL-] button.
• TO CHANGE THE POSITION OF PIP WINDOW
• TO SEE PHOTOS IN SLIDE SHOW MODE
Select a photo in the list; then press [OK] button to enter slide show mode.
✍ Note>>>
To see the help panel, press [OK] button in slide show mode.
Press [Yellow] button to change PIP screen position: Up-Right, Down-Right, Down-Left
and Up-Left.
• TO LEAVE SLIDE SHOW MODE
Press [Menu] button or [Exit] Button.
USING JPEG FILE OPERATION
It is same as MP3 File Operation.
For more information about File Operation, see “Using
MP3 File Operation” on page 67.
68
69
18
USING GAMES
Choose [Main Menu ] >>[9 Multimedia Games ] >[3 Games ].
CHAPTER
>> MULTIMEDIA COMMUNICATION
WITH PC SOFTWARE
• USB PORTS
There are two USB ports in PVR: one on the front panel and one on the rear panel.
Front USB port: USB 1.1 host controller is used for devices as digital camera and MP3
player.
Rear USB port: USB 2.0 high-speed is used for connection with PC.
✍ Note>>>
• TO START GAME
Select a game in the list; then press [OK] button to start
game. When you select a game, Game Screen Image and Information are shown on the right
side.
To use PC Software, you should connect PC via USB 2.0 port on rear panel. For more information, see
“Connecting to PC” on page 15.
• INSTALL PC SOFTWARE
In order to install PC Software for PVR, please follow the below instructions:
• TO INSTALL GAME
1 Insert the included CD-ROM to your CD ROM Drive.
In PC Software, select “Game” menu and transfer downloaded game binary image.
Games are on the CD-ROM. And games will be released on the web.
2 Select "Setup.exe"; then click.
• TO UNINSTALL GAME
3 When installation is completed, reboot your PC.
DirectX 9 runtime library is needed.
Select a game in the list; then press [Red] button to uninstall game.
• TO CONTROL GAME
Use Arrow Keys to control movement and use [OK] button to do action.
Press [Right Arrow] button to move right. Press [Left Arrow] button to move left. Press
[OK] button to do action in the specific game.
• TO QUIT GAME
Press [Exit] button or [Menu] button to quit game.
USING PLUG-INS
Choose [Main Menu] >>[9 Multimedia Games] >>[4 Plug-in Interface].
• TO INSTALL PLUG-IN
In PC Software, select “Plug-in” menu and download
plug-in image file.
• TO UNINSTALL PLUG-IN
Select Plug-in in the list; then press [Red] button.
70
71
• USING PC SOFTWARE
Run "PVRUSB.exe".
The following window will appear.
• USING RECORD MANAGER
You can exchange recorded videos, MP3, JPG files between PC and PVR. Also, you can
choose to play each file on PC. Press [Record] button in
the PC program. Then “Record Manager” program appears
as follows.
• MENU AND OPERATION
As in the above window, there are independent icons for the following purposes: Record,
MP3, JPEG, Games and Upgrade.
• BASIC OPERATION
DOWNLOAD : To transfer selected files or directories from PC to PVR.
UPLOAD : To transfer selected files or directories from PVR to PC.
You can transfer recorded files between PVR and PC if
PVR is connected to your PC. If PVR is not connected,
[Record Manager] program works in stand-alone mode,
and you can playback previously downloaded recordings
from your PC hard disk.
REFRESH : To refresh the contents of current directory.
DELETE : To delete selected files.
NEW FOLDER : To create new folder.
BACK &FORWARD : Path History
MULTI-VIEW in Record Manager and JPEG Manager : To show contents in thumbnailmode.
RADIO in Record Manager only : Toggle TV/Radio Recordings.
SETTING in Record Manager only : To set up a directory in which recordings are
transferred.
“File Download Dialog” in Game/ Plug-in Manager: Managing Games and Plug-in
application
“Open”and “Save” in Channel Manager: To manage PVR channel data in specified file
type
“Load from PVR” and “Send to PVR” in Channel Manager: To transfer channel data
between PC and PVR
“Create Favorite”, “Add to Favorite” and “Delete” in Channel Manager: Managing
Favorite Channel Group
• USING MP3 MANAGER
Press [MP3] button in the PC program; then [MP3 Manager] program appears as follows.
When PVR is connected to your PC, you can transfer
MP3 files between PVR and PC. Also, you can play MP3
files in PVR using this program in addition to files in your
PC. If PVR is not connected, “MP3 manager” program
works in stand-alone mode. You can search and playback
MP3 files from your PC hard disk.
“SatcoDX Import” in Channel Manager: Managing Satco-DX channel information
• MOUSE OPERATION
Drag-and-drop to transfer selected files between PVR and PC.
Double click to play selected files.
72
73
• USING JPEG MANAGER
Press [JPEG] button in the PVR MANAGER program. Then [JPEG MANAGER] program
appears as follows.
USING CHANNEL MANAGER
You can edit channels from your PC via USB connection.
• EDIT CHANNEL DATA
You can transfer JPG files between PVR and PC, if PVR
is connected to your PC. Slide-show functionality is also
provided regardless of location of the files. JPEG Manager
has thumbnail view option: Multi-view. If PVR is not
connected, JPEG Manager works in stand-alone mode.
You can search and playback JPG files from your PC hard
disk.
You can edit your PVR channel data in a specified file
format: User Favorite File (uff file). This file contains all the
channel information including favorite group list. If you
once create it, then you can use it for other PVR as well.
• COMMUNICATING WITH PVR
You can load channel data from PVR and edit it in the
way you want. After editing it, you can send it back to the
PVR. Then, the channels will be displayed as in the way you edited in PC.
• FAVORITE GROUP MANAGEMENT
• USING GAME/PLUGIN MANAGER
You can install games on PVR. Click “Game” Icon; then dialog appears to load game
image file.
Select a game image file, and click “...” button. If selected game image file has the correct
format, the game is transferred and installed automatically in your PVR.
You can edit PVR favorite group in your PC Program: creating favorite, adding channel to
the group, removing from it, renaming and deleting favorite group.
• SATCODX IMPORT
SatcoDX is a widely known satellite channel information protocol. You can import
SatcoDX data to your PVR.
• UPGRADE
You can upgrade firmware of PVR easily using this program.
First please select files to be updated using [...] button
and press [Start] button. Only if the selected file has the
correct format, the program transfers it to PVR and
Firmware will be updated.
74
75
CHAPTER
19>>
CHAPTER
MENU MAP
GLOSSARY
DiSEqC (Digital Satellite Equipment Control)
Main Menu
A standard through which it is possible to let a DiSEqC compatible receiver send a signal
over the RF cable to a switching device to switch between different LNBs or dishes. The
DiSEqC uses the 22KHz signal to control the switching device.
ChannelGuide
OrganizeChannel
Edit TV Channel
Edit Radio Channel
Edit TV Favorite
Edit Radio Favorite
Program Guide (Electronic Program Guide,EPG)
Program Guide
Program Guide Grid
Program Finder
System Setup
An unscrambled broadcast, which you can view without additional payments to a service
provider.
HDD Management
USB Devices
EasyInstallation
Antenna Setup
Recording List
The primary computer storage medium, which is made of one or more aluminum or glass
platters, coated with a ferromagnetic material.
Hi-Fi (High Fidelity)
Tuner1
Tuner2
LNB (Low Noise Block)
Tuner1
Tuner2
OSD (On Screen Display)
Channel Search
Motorized Antenna
Language Setup
Timer Setup
Parental Lock
Appearance Setup
PVR Setup
EPG Setup
HDD (Hard Disk Drive)
The characteristics of audio devices that can play back all the audio frequencies of the
human, which is the range of 16Hz -20KHz, uniformly from the low frequency to high
frequency. Sometimes it is used to indicate good quality of an audio device such as stereo
tape recorder.
Installation
User Preference
Frequency
FTA (Free–To–Air)
System Information
Factory Default
Transfer Firmware
Transfer Channel Data
SatcoDX
Edit Satellite
Edit Transponder
A electronic program guide (EPG) that comes with the broadcast to a particular satellite,
note that every station fills the EPG differently or not, so differences in the EPG are not
necessarily receiver errors.
The number of cycles or events per one second, which is expressed in the unit of hertz.
TV Setting
Time Setting
Common Interface
STB Management
An electronic unit mounted on the satellite dish. It receives the signals reflected by the
dish and converts them to signals that can be used by this receiver.
The function that displays the information about the monitor that the user needs or has to
know on the screen directly. OSD information includes brightness, contrast, tuning, RGB
adjustment, and screen size and positions (top, left, width, and height), and so on.
OTA (Over The Air)
Means that software downloads where the manufacturer reserves the right to decide when
and where to release them through satellite system.
PID (Packet Identifier)
A set of numbers that identifies the transport streams packets that containing data from a
single data stream.
Edit Recording
PIP (Picture In Picture)
Create Reminder
TV screen which can display another small screen within the main screen. In TV, the
background screen is called the parent screen and the small screen is called PIP.
Reminder List
76
20>>
77
CHAPTER
21>>
TROUBLESHOOTING
Video recorder that can record and playback program directly using the embedded hard
disk drive(s).
Before contacting your local service, please make sure following instructions. If the
receiver does not work normally after completing the following trouble shooting, please
contact your local receiver distributor.
RF (Radio Frequency)
1. NO MESSAGE IS DISPLAYED ON THE FRONT PANEL OR RECEIVER HAS NO POWER.
Frequencies occupied by radio waves of the total frequency range of electromagnetic
waves.
√ Check the power cord and check if it is plugged into a suitable power socket.
SCART
2. NO PICTURE
A 21-pin connector used for connection of this receiver, VCR and TV. Also called
Euroconnector or Peritel connector.
√ Make sure that the receiver is in operation.
PVR (Personal Video Recorder)
S/PDIF (Sony/Philips Digital Interface format)
Standard format for digital audio output. It outputs audio signals directly as digital audio
signals without changing into analog signals because conversion into analog signals can
degrade signal quality.
√ Check whether the PVR is On. Press Power button on the remote control.
√ Make sure that the AV Cable is firmly connected to the TV.
√ Make sure that Antenna line is correctly connected to the equipment.
√ Make sure that Antenna Setting is correct.
√ Check the brightness level of TV.
Transponder
√ Check the channel is on air.
An automatic device that receives amplifies and retransmits a signal on a different
frequency.
√ Check the channel is scrambled.
3. POOR PICTURE &SOUND QUALITY
TSR (Time Shifted Recording)
√ Install the antenna in a place where there is no obstacle.
A function that record the present program temporarily to support trick-play.
Trick-Play
Pause, Fast Forward, Backward, Slow Motion, Instant Replay
√ Make sure that there is no mobile phone or microwave oven near the equipment.
√ Use correct cable (75 Ohm) to connecting TV and antenna.
√ Check if the antenna cable is firmly connected to the receiver.
√ Make sure the receiving level, and adjust antenna if the level is low. The receiving level
can be influenced by weather.
√ Replace LNB with the one with low noise factor if the noise factor is high.
√ Replace LNB with a new one if it is damaged or out of order.
4. NO OR POOR SOUND
√ Check the volume level of the TV and Receiver.
√ Check the mute status of the TV and Receiver.
√ Press the Audio button to change the Sound Track type.
5. REMOTE CONTROLLER DOES NOT OPERATE.
√ To control the equipment with the remote controller, the remote controller's top end
should directly point towards the receiving part of receiver's remote controller.
√ Check the battery of Remote controller.
6. WATCHING SCRAMBLED CHANNEL IS NOT AVAILABLE.
√ Check the correct Smart Card is plugged in.
√ Check whether the Smart Card is damaged.
78
79
CHAPTER
22>>
TECHNICAL SPECIFICATION
Tuner and Channel Decoder
Power Supply
Input/ Loopthrough Connector
75 Ohm, IEC 169-24, Female 2 LNB Input, 2 LNB Output
Input Voltage
90~250V AC, 50/60 Hz
Frequency Rate
950~2150 MHz
Type
SMPS
Signal Level Output
-65 ~ -25 dBm
Power Consumption
TBD
DiSEqC Control
1.0/ 1.2/ USALS
Standb-By Power
TBD
MPEG Transport Stream A/V Decoding
Physical Specification
Transport Stream
ISO/IEC 13818-1 MPEG-2
Size
380 x 70 x 300 (mm)
Profile Level
MPEG-2 MP@ML
Weight
TBD
Aspect Ratio
4:3, 16:9, Pan & Scan, LetterBox
Operation Temperature
TBD
Video Resolution
720x576
Audio Decoding
MPEG-1 Layer 1, 2 & 3
A/V and Data In/Out
TV-SCART
Video CVBS/ S-VIDEO/ RGB/ YPbPr Output
Audio L/R Output
VCR-SCART
Video CVBS Output
Audio L/R Output
Video CVBS/ S-VIDEO/ RGB Input Bypass
Audio L/R Output
RCA A/V
Video CVBS Output
Audio L/R Output
S/PDIF
Digital Audio / Dolby AC-3 Bitstream Output
RS-232C
Transfer Rate 115200 bps
USB
USB 2.0 High Speed Device Controller
9 pin D-Sub Type
USB 1.1 Host Controller
Main System
Main Processer
Power PC
Memory
Flash-ROM 4MB
RAM 40MB
EEPROM 2KB
HDD
80
80 GB
81

chapter 3>> connecting pvr

Transcription

Similar documents

Untitled - Brookstone

Flatbed

Online Academic Record Change

Win 8 regional language settings

Hotmail/Live/ MSN/Outlook.com

How to retune the Panasonic 2007 range of Viera Televisions

25W POWER MEGAPHONE

tv tuner cards and video clips

Mega Plexxus Instruction