ironside - Shur-Co

IRONSIDE™
ELECTRIC SIDE DUMP TARP
CONSTRUCTION DIVISION
C010FL-0316
Features
Applications
• 2-Inch Square 14-Gauge Steel Tubing
• Side Dump Trailers
• Robust Boxed Hinge
• Accommodates Most
• Heavy-Duty Spiral Torsion Spring
Makes & Models
• Gear-Reduced Chain Drive
• 3-9/16-Inch Extruded Aluminum Roll Tube
• Reinforced Mesh or Solid Vinyl Fabric Cover
• All-Steel Structural Components Shur-Seal™
Plated for Corrosion Resistance
WWW.SHURCO.COM
IRONSIDE™
CONSTRUCTION DIVISION
Accommodates Most Side Dump Trailers
Description
The IronSide™ electric roll tarp from Shur-Co® has been specifically designed and
built to survive the harsh hauling conditions of side dump applications. The IronSide™ is aptly named, with all structural components manufactured from steel for
maximum strength and superior performance.
The IronSide™ allows the trailer to be loaded or unloaded from either side, with the
tarp stored in a protected position underneath the side rail of the trailer.
Distribution and Service on Six Continents!
Features
Durable Steel Tubing
The IronSide™ features spring-return arms constructed from durable
2-inch square 14-gauge steel tubing that are plated for corrosion resistance. The IronSide™ utilizes
a simple free-swinging arm design with a robust
boxed hinge for increased support.
Gear-Reduced Chain Drive
Driven by
reliable worm-gear motor technology, the IronSide™ uses a gear-reduced chain drive. This allows
the roll tube to be driven by a drive shaft fully supported on both sides with triple sealed bearings,
eliminating the severe overhung load and stress on
the motor shaft typically seen with systems using a
motor with direct attachment to the roll tube.
Extruded Aluminum Roll Tube
The
IronSide’s 3-9/16-inch OD extruded aluminum roll
tube allows the tarp to be lifted and suspended over
loads with minimal deflection and without tarp support bows inside the trailer tub.
Robust Hinges for Increased Support
The hinged design of the return arms allows the
tarp to be tightened underneath the side rail in the
closed position. This limits tarp movement in transit and increases the life of the tarp. There are no
complex rollers or spring-loaded knuckles to bind or
wear out.
Adjustable HD Torsion Springs
The
arms are connected to heavy-duty torsion springs
with adjustable pre-load at the arm pivots. Spiral
springs last longer and are more reliable than the
clock springs used by other side dump tarp systems
on the market. The IronSide’s springs can be easily
readjusted at the pivot point to bring the spring rate
back to top performance levels.
Durable Mesh Fabric Cover
The IronSide™ tarp is constructed from a durable mesh fabric reinforced on the sides with 22-ounce solid vinyl
fabric and webbing on the ends of the tarp.
Serving You Worldwide
For more information on the IronSide™, contact your local Shur-Co® dealer or
your nearest Shur-Co® location, or visit us online at www.SHURCO.com.
SHUR-CO® of S. Dakota
SHUR-CO® of OHIO
SHUR-CO® of N. DAKOTA
SHUR-CO® of TEXAS
SHUR-CO® of FLORIDA
1.877.729.2969
1.866.356.0242
1.877.868.4488
1.866.689.0039
1.800.327.8287
Yankton
Ravenna
Fargo
Brookshire
Stuart
SHUR-CO® of Colorado
SHUR-CO® of ILLINOIS
SHUR-CO® of IOWA
SHUR-CO® of OKLAHOMA
SHUR-CO® of Michigan
1.866.355.9173
1.866.356.0246
1.866.356.0245
1.866.356.0243
1.800.327.8287
Henderson
Decatur
Fort Dodge
El Reno
Lexington