Technical_Report_EU3..

Transcription

Technology Topics EU3
November 2009
© Cinterion Wireless Modules GmbH 2009, All rights reserved
Confidential
HW Features
HW Topics
Page 2
Strictly Confidential
Cinterion Wireless Modules
EU3 accessiories
Page 3
DSB
SPECIAL ADAPTER required for EU3 at DSB75!
Well known DSB75 for EU3 (with adapter)
Evaluation board for testing and debugging
Test pins and status LEDs
Kit including DSB75, Quad-Band antenna,
handset, cables and mounting kit
Available under separate order number:
DSB75:
L36880-N8811-A100
Adapter Board: L30960-N1701-A100
Page 4
DSB75 + EU3 adapter
Why need special DSB adapter for EU3?
1. USB 2.0 High Speed interface does not work with DSB75 USB wires!
2. Logic level EU3: 2.6V -> level adaption for DSB75
Page 5
Mechanical dimensions MC75 -> MC75i -> EU3
MC75i
Length and width: 35mm x 33.9mm
EU3-E
Length and width: 44.6mm x 33.9mm
(PH8: 55mm x 33.9 x single sided)
Height: 3.3mm (single sided)
Height: 5mm (double sided)
Weight: approx. 7.5g
Weight: approx. 10g
Same 80-pin board-to-board connector at same position, same pin layout.
Same mounting holes at same position: 1 round hole and 2 oblong holes
Please note: it was intentionally decided NOT to support MC75 mechanics!
Page 6
PIN differences M2M Evolution Platform (TC65i) <->
EU3
Page 7
M2M Platform
EU3
GND
ADC1_IN
ADC2_IN
GND
GPIO10
GPIO8
SPIDI
GPIO7
GPIO6
GPIO5
I2CCLK_SPICLK
VUSB_IN
DAI5
ISENSE
DAI6
CCCLK
CCVCC
CCIO
CCRST
CCIN
CCGND
DAI4
DAI3
DAI2
DAI1
DAI0
BATT_TEMP
SYNC
RXD1
RXD0
TXD1
TXD0
VDDLP
VCHARGE
CHARGEGATE
GND
GND
GND
GND
GND
GND
ADC1_IN
ADC2_IN
GND
GPIO10
GPIO8
not connected
GPIO7
GPIO6
GPIO5
do not use
VUSB_IN
do not use
do not use
do not use
CCCLK
CCVCC
CCIO
CCRST
CCIN
CCGND
do not use
do not use
do not use
do not use
do not use
do not use
do not use
STATUS1
RXD0
not connected
TXD0
VDDLP
do not use
do not use
GND
GND
GND
GND
GND
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
EU3
M2M Platform
GND
GND
DAC_OUT
PWR_IND
do not use
GPIO9
SPICS
GPIO4
GPIO3
GPIO2
GPIO1
I2CDAT_SPIDO
USB_DN
USB_DN
VSENSE
VMIC
EPN2
EPP2
EPP1
EPN1
MICN2
MICP1
MICP2
MICN1
AGND
IGT
EMERG_OFF
DCD0
CTS1
CTS0
RTS1
DTR0
RTS0
DSR0
RING0
VEXT
BATT+
BATT+
BATT+
BATT+
BATT+
do not use
PWR_IND
do not use
GPIO9
not connected
GPIO4
GPIO3
GPIO2
GPIO1
do not use
USB_DN
USB_DN
VSENSE
VMIC
not connected
not connected
EPP1
EPN1
not connected
not connected
MICP1
MICN1
AGND
IGT
EMERG_OFF
DCD0
STATUS0
CTS0
not connected
DTR0
RTS0
DSR0
RING0
VEXT
BATT+
BATT+
BATT+
BATT+
BATT+
Page 8
Temperature behavior MC75i -> EU3
Please note: expected maximum Thermal Power Dissipation will be in UMTS modes
and will be in range of 2 Watt !!
w/o heat sink, there will be a risk of connection interrupts!
Page 9
Startup timing MC75i -> EU3
Page 10
Emergency Off Behavior MC75i -> EU3
Page 11
Interfaces Features
MC75i / TC65i / AC75i
EU3
Power Supply range
Power Supply range
– 3.2V to 4.5V
– 3,3V to 4,2V
SPI interface
SPI interface
– supported
– not supported
I2C interface
I2C interface
– supported
– not supported
Logic levels
Logic levels
–2,9V
– 2,6V
Analogue Audio interface
Analogue Audio interface
– 2 interfaces supported
– 1 interfaces supported
Digital Audio interface
Digital Audio interface
– Master/Slave, bit clock 256kHz or 512kHz,short or long frame
Status signalization
– Sync Pin
Charging control
– supported
Page 12
– not supported
– STATUS 0 and STATUS 1 Pin
Charging control
– not supported
Interfaces Features
EU3
Full Speed USB 2.0 (12Mbit/s) interface
High Speed USB 2.0 (480 Mbit/s) interface
– Remote Wakeup support
– Includes Full speed
– USB Composite device (single virtual COM PORT Variant)
– Remote Wakeup support
– USB Composite device (Dual virtual COM PORT Variant)
High Speed Serial Interface (460 Kbps)
– two interfaces (ASC0 and ASC1)
High Speed Serial Interface (460 Kbps)
– covers UMTS data speed (384 Kbps)
– one Interface only
Multiplex-Protocol GSM 07.10
–Same as EU3
Multiplex-Protocol GSM 07.10
(up to five logical channels)
– Up to five logical cannels
– Mux protocol according to GSM 07.10
– Can be used on first physical or logical interface (other
interfaces will be inactive)
– Mux driver will be available for WinXP and Win Vista
– A MUX driver reference implementaion according to GSM 7.10
will be provided as a source code delivery to the customer
Linux conform USB Driver interface
– same as EU3
Page 13
Linux conform USB Driver interface
– registers as a composite device with CDC_ACM profile
Interfaces Features
No GPIO available
TC65i / AC75i - Same as EU3
EU3
10 Pin GPIO Interface
– Can be configured via the AT command interface.
– Configuration of 10 GPIO pins as Input or output. Used pins are
GPIO1 to GPIO10.
– Configuration of GPIO pin as input with polling functionality
– 10ms poll duration is every TDMA frame in GSM service and
every frame in UMTS service
– up to 2.7s during activated power saving (depending of power
saving mode)
– Usage of all 10 GPIO pins by other functionality is completely
restricted
No ADC available
TC65i / AC75i - 2xADC/1xDAC
Real Time Clock (RTC)
– Same as EU3
Analog/Digital Converter (ADC) Interface
– Can be configured via the AT command interface.
Real Time Clock (RTC)
– The clock will run while the board is powered by BATT+
– Associated timer features (here: setting the clock, query
current time) will be provided to the user via the AT interface.
– No RTC alarm
Page 14
Network Features
EU3
NITZ (Network Identity and Time Zone Indication)
– GSM
24.008, ch. 9.2.15a and 9.4.19
Jamming Detection
– Jamming detection will be available for GSM/GPRS in idle, packet transfer and active mode
Configurable Support of MS-Class of Operation (B, C)
– B - MS can register for voice / data services, but can only handle one kind of services at a time.
– CG - MS can only register for packet services
– CC - MS can only register for voice / CSD services
Voice and data can be transferred simultaneously in 3G (MS-Class A)
Multi band selection
–Selective switching off/on of unwanted bands by AT command
–Configurable search order of GSM and WCDMA bands
Page 15
Technical Features
EU3
Support of Video Calls
– The module will forwared the raw video data stream (multiplexed, encoded, crypted, etc.), received
from the network, to the application
– Respectively, the user shall be able to establish outgoing video calls
– Videocall will be realized similar CSD Call. The AT commands (at+cbst, +es, +esa) are used to prepare
the call.
– The incoming/outgoing datacall will use these settings (synchron, transparent, multimedia 64kb/s).
– After call setup the data will be exchanged transparent via USB with the application.
– The transparent exchanged data and the protocol are based on H324M
– No video codec on board
MMS
– Customer implementation has to be done to support MMS.
– The discussion is ongoing to support MMS on board
FAX
– Group 3, Class 1
– Transparent mode 3GPP TS62.
– Transfer rates between 2k4 and 9k6
Page 16
Technical Features
EU3
Robustness against Power Supply Loss (especially while flash access routines (write/read) are ongoing)
– If hardware under voltage, generate the power down sequence if the BATT+ voltage falls below
2.55V
– Sudden Momentary Power Loss (SMPL) feature initiates a poweron sequence if BATT+ drops outof-range (< 2.55 V nominal) then returns in-range within a programmable interval of between 0.5 and
2.0 seconds (prepared by hardware).
Hot SIM Removal/Insertion
– When detecting a removal of a SIM card during normal operation, the SIM interface will be switched
off and the protocol stack will be shut down (reset) immediately, including aborting any ongoing call
or data transmission.
Autobading
– Autobauding is supported.
– Autobauding is not compatible with multiplex mode (If autobauding is active you cannot switch to
multiplex mode).
– The autobaud mode is activated with the next restart of the TA after entering AT+IPR=0
Page 17
FW Update
EU3
Firmware Upgrade via USB/Serial Interface
–
Generic FW update via Serial and USB Port (gSwup)
– Update algorithm can be provided to the customer
– Firmware size 8 MB
– gSwup.exe and FW.usf files will be available
Separate Application Revision String
– ATI1 with additional (A-REVISION<number>) string
Page 18
Drivers
EU3
Win XP
– USB Driver ( inf file )
– Mux Driver ( binary / sources )
Win CE
– USB Driver ( sources )
– Mux Driver ( sources )
Linux
– USB Driver ( default CDC_ACM driver)
Page 19
HC25 migration path
No migration document planned
Mechanically different – but software and feature compatible
Page 20
Mechanical dimensions HC25 <-> EU3
HC25
Length and width: 50mm x
34mm
EU3
Length and width: 44.6mm x
33.9mm
(PH8: 55mm x 33.9 x single
sided)
Height: 4.5mm (double sided)
Height: 5mm (double sided)
Weight: approx. 10g
Weight: approx. 10g
50-pin board-to-board connector 80-pin board-to-board connector
Different mounting holes and position
Page 21
Hardware differences HC25 -> EU3
Feature
UMTS bands
HC25
Triple band: 850/1900/2100MHz
EU3-E
Dual-Band: 900/2100MHz
GSM/GPRS/EDGE bands
Quad-Band: 850/900/1800/1900MHz
Dual-Band: 900/1800MHz
Power supply range
3.2V to 4.2V
3.3V to 4.2V
Serial Interface(s)
8-wire modem interface (ASC0)
8-wire modem interface (ASC0)
GPIO pins
SPI interface
I2C interface
Analogue Digital Converter (ADC)
No
No
No
No
10 GPIO pins
No
No
Yes, 2 analogue inputs
Logic level (digital pins)
2.6V
2.6V
Analogue audio interface
1 analogue audio interfaces
1 analogue audio interface
Digital audio interface
No
No
USB interface
Supports USB 2.0 Full Speed device Supports USB 2.0 High Speed device
interface
interface
STATUS0 and STATUS1 pins
STATUS0 and STATUS1 pins
Charging control
No
No
DSB75 usage
DSB75 requires special adapter board to DSB75 requires special adapter board to
connect the module
connect the module (order no.: L30960N1701-A100)
Page 22
HW Features
SW Topics
Page 23
Network Monitoring
EU3
AT^SMONI (Monitor idle mode)
– ME
is camping on a 2G cell
^SMONI: ACT,ARFCN,BCCH,MCC,MNC,LAC,cell,C1,NCC,BCC,GPRS
Example:
^SMONI: 2G,71,-61,262,02,0143,83BA,33,3,6,G
– ME
is camping on a 3G cell
^SMONI: ACT,UARFCN,PSC,EC/n0,RSCP,MCC,MNC,LAC,cell,SQual,SRxLev
Example:
^SMONI: 3G,10564,296,7,-79,262,02,0143,3B2F,-92,-78
AT^SMONP (Monitor neighbour cells)
– Jamming detection will be available for GSM/GPRS in idle, packet transfer and active mode
2G:
ARFCN1,BCCH1
ARFCN2,BCCH2
3G:
UARFCN1,PSC1,EC/n01,RSCP1
UARFCN2,PSC2,EC/n02,RSCP2
Page 24
Internet Services
EU3
Transparent TCP Service / UDP Client Service
– The Transparent TCP Socket Service provides access to two independent streams embedded within the
Internet Service architecture
– The service is limited to IPv4 only and accepts either numeric or symbolic IP addresses
– Using of Hardware Flow Control is strongly recommended
• AT
Commands
• AT^SICS (Internet connection settings)
•AT^SISS (Internet service setup profile)
•AT^SISO (Internet service open)
•AT^SISC (Internet service close)
•AT^SISR (Internet service read data)
•AT^SISW (Internet service write data)
•AT^SIST (Internet service enter transparent mode)
•AT^SISX (Internet service execution, PING)
•AT^SISE (Internet services error report) status is identical with ^SIS report
– Leave transparent mode can be performed with
• +++ sequence
• DTR ON-OFF
– Higher Protocols are not supported (FTP, HTTP, POP3, SMTP)
Page 25
Technical Features – AT commands
New AT commands
Short Message Service (SMS) Commands
AT+CMMS (More Messages to Send)
Phonebook Commands
AT+CPBF (Find phonebook entries)
Call related Commands
AT+CSTA (Select type of address)
AT+ES (Synchronous Data Mode Configuration)
AT+ESA (Synchronous access mode configuration)
AT+FAR (Adaptive Rate Control)
Hardware related Commands
AT^SLED (LED Feature)
Page 26
New AT commands
FAX Commands
AT+FCL (Carrier Loss Timeout)
AT+FDD (Double Escape Character Replacement)
AT+FIT (DTE Inactivity Timeout)
Network Service Commands
AT^SMONI (Monitor idle mode)
AT^SMONP (Monitor neighbour cells)
Serial Interface Control Commands
AT+SQPORT (Query Port Type)
Page 27
Not available AT commands
AT&W (Stores current configuration to user defined profile)
AT+CALA (Set alarm time)
AT+CGANS (Manual response to a network request for PDP context activation)
AT+CGAUTO (Automatic response to a network request for PDP context activation)
AT+CIND (Indicator control)
AT+CLVL (Loudspeaker volume level)
AT+CMER (Mobile Equipment Event Reporting)
AT+CPIN2 (PIN2 Authentication)
AT+CSDH (Show SMS text mode parameters)
AT+CSNS (Single Numbering Scheme)
AT+CXXCID (Display card ID)
AT+ICF (Character Framing)
AT+IFC (Flow Control)
Page 28
AT+ILRR (Set TE-TA local rate reporting)
AT+VTD (Tone duration)
AT\V (Set CONNECT result code format)
AT^MONI (Monitor idle mode and dedicated mode)
AT^MONP (Monitor neighbor cells)
AT^SACM (Advice of charge and query of ACM and ACMmax)
AT^SAIC (Audio Interface Configuration)
AT^SALS (Alternate Line Service)
AT^SATR (Query SIM's Answer to Reset Data)
AT^SBC (Battery Charge Control)
AT^SCID (Display SIM card identification number)
AT^SCML (List Concatenated Short Messages from preferred store)
AT^SCMR (AT^SCMR Read Concatenated Short Messages)
Page 29
AT^SCMS (Send Concatenated Short Messages)
AT^SCMW (Write Concatenated Short Messages to Memory)
AT^SCNI (List Call Number Information)
AT^SDLD (Delete the 'last number redial' memory)
AT^SFNUR (Select the fixed network user rate)
AT^SGACT (Query all PDP context activations)
AT^SGCONF (Configuration of GPRS related Parameters)
AT^SHOM (Display Homezone)
AT^SICC (Internet Connection Close)
AT^SICI (Internet Connection Information)
AT^SICO (Internet Connection Open)
AT^SICS (Internet Connection Setup Profile)
AT^SISC (Internet Service Close)
Page 30
AT^SISE (Internet Service Error Report)
AT^SISI (Internet Service Information)
AT^SISO (Internet Service Open)
AT^SLCD (Display Last Call Duration)
AT^SLCK (Facility lock)
AT^SMGO (Set or query SMS overflow presentation mode or query SMS overflow)
AT^SMGR (Read short message without setting status to REC READ)
AT^SMONC (Cell Monitoring)
AT^SNFA (Set or query of microphone attenuation)
AT^SNFM (Set microphone audio path and power supply)
AT^SNFPT (Set progress tones)
AT^SNFV (Set loudspeaker volume)
AT^SPBC (Find first matching entry in sorted phonebook)
Page 31
AT^SPBD (Purge phonebook memory storage)
AT^SPBG (Display phonebook entries in alphabetical order)
AT^SPBS (Step through the selected phonebook alphabetically)
AT^SSCONF (SMS Command Configuration)
AT^SSDA (Set SMS Display Availability)
AT^SSMSS (Set Short Message Storage Sequence)
AT^SSPI (Serial Protocol Interface)
AT^SSYNC (Configure SYNC Pin)
AT^STCD (Display Total Call Duration)
AT^STPB ( Transmit Parity Bit (for 7E1 and 7O1 only))
ATS18 (Extended call release report)
ATS2 (Set escape sequence character)
Page 32

Technical_Report_EU3..

Transcription

Similar documents

Vodafone template - Microsoft Advertising

get protected! - Pine Cellular

Silego Technology - Globalpress Electronics Summit

fora family?

- Saurashtra University

Event Invitation

ETRM Solutions - Primetech Systems Inc.

Q-Bass-U 2.1 Audio - LTB Audio Systems

Manufacturing Energy Management Solution (MEMS)

SignalPro® - EDX Wireless