concrete resurfacer

CDS_0009 | CRS 020
CONCRETE RESURFACER
RESURFACER FOR AGED OR SPALLED CONCRETE
DESCRIPTION:
Cemix®Concrete Resurfacer is a high performance concrete resurfacing product for
aged or spoiled concrete. It serves to resurface good quality concrete with a thin
coating in situations where the surface is aged, stained, rain damaged, cracked or
worn away. Its use serves to prevent the removal & replacement of good quality
concrete. It is applied with a steel squeegee, trowel or broom brush finished.
IMAGE
20kg
APPLICATION:
Dampen concrete substrate with a light spray
of water. Avoiding ponding, apply the first coat
immediately after mixing the product. Use a
suitable steel squeegee, trowel or brush to
force product into the surface. After the first
coat has completely dried, mix up a new batch
of Resurfacer. Dampen the surface with a light
spray of water and apply the second coat in
the same manner. A third coat may be applied
if required. If a broom finish is required, broom
the surface immediately after the final coat
of product has been applied. The total finish
thickness should be approximately 2mm - 3mm.
TYPICAL APPLICATION/USES:
• Resurfacing of aged concrete
• Resurfacing of surface spalled concrete
• Resurfacing of cracked concrete after undertaking crack repairs
• Residential driveways
• Patios
• Footpaths
• Shops, Restaurants & Cafes
• Hospitals
• Schools
• Overcoat ‘ugly’ concrete repairs
ADVANTAGES:
• Cost effective
• High bond strength
• Flexible
• Durable
SUBSTRATE PREPARATION:
Surfaces should be sound & rough to ensure a good bond. They should be
uncoated & clean, free from all contaminants, loose particles, dirt, oil, mould, curing
compounds, sealers & paints etc. Acid washing or honing & then water blasting is
required to prepare the surface depending on substrate condition. Washing with
soap & water blasting may also be required if oil is present. Holes, spalls, low spots,
uneven and deteriorated surfaces should be patched with a suitable Cemix repair
mortar and bonding agent. The better the substrate preparation & condition the
better the end result. The concrete substrate should ideally be at least three months
old.
CRACKS IN CONCRETE:
Cracks in the concrete substrate must be well repaired with suitable
products prior to product application. Seek technical advice if required.
MOVEMENT / CONTROL JOINTS:
Honour any control joints in the concrete substrate – do not apply product
over control joints. If required create control joints in substrate at suitable
locations.
CEMIX LTD
19 ALFRED STREET
ONEHUNGA 1061
AUCKLAND
NEW ZEALAND
0800 ASK CEMIX
WWW.CEMIX.CO.NZ
TECHNICAL DATA:
STRENGTH:
25MPa @ 28 days
APPEARANCE:
Sand / Cementitious
APPLICATION
TEMP:
5°C - 30°C
WORKING TIME:
40mins @ 20oC
The data shown above reflects typical results based on
laboratory testing under controlled conditions. Reasonable
variations may occur on site.
Precaution:
• Avoid rain damage until the product has set. Protect the product from freezing for at least one day.
• Variations in colour & texture in the finished surface should be expected.
• This product may not be suitable for certain very high wear applications.
• Variations in colour & texture in the finished surface should be expected.
COVERAGE:
Approximately 1m2 for every 2kg of product for
two coats. Therefore 20kg will do approximately
10m2 for two coats. A rough substrate surface
texture & additional coats will consume more
product.
PACKAGING:
Cemix®Concrete Resurfacer comes in 20kg
bags.
STORAGE & SHELF LIFE:
Store Cemix®Concrete Resurfacer Can be
stored in its original container in a dry place well
sealed for a period of twelve (12) months after
production. Do not store opened bags & pails.
CLEANING:
Clean all tools with water & brush immediately
after use.
CEMIX LTD
19 ALFRED STREET
ONEHUNGA 1061
AUCKLAND
NEW ZEALAND
0800 ASK CEMIX
WWW.CEMIX.CO.NZ
MIXING:
Mix full bags of product. Mix the product separately for each coat. Add
water to product, not product to water. Mix the product with a drill & paddle
thoroughly for at least 4 - 5 minutes. Mix to a pourable consistency.
Maximum water addition is 4L of water per 20kg bag. Mix until all cement
lumps have been broken down. Use product immediately. Mixing water
temperature should ideally be between 15ºC - 22º C.
POST APPLICATION:
Avoid rain damage until the product has set. Protect the product from freezing for at
least one day.
COLOUR & STAINING:
Contact Cemix®for advice on colouring & staining the product.
SEALING:
To enhance surface appearance and increase durability, seal the surface the
next day with a suitable Cemix clear sealer such as Pavseal (water based) or
Driveseal (solvent based for external use only).
LIMITATIONS:
Substrate Temperature - +5°C min. / +30°C max.
Ambient Temperature - +5°C min. / +30°C max.
Not to be used as a mortar for repairs >3mm deep.
SAFETY:
Avoid contact with eyes & skin, both from wet & dry mix. Do not breathe in dust.
Wear suitable protective clothing, gloves, eye protection & barrier cream. Wear a
suitable dust mask. Wash thoroughly after handling & store any leftover material
properly.
FIRST AID:
Irrigate eyes & skin with plenty of water & seek medical advice immediately.
SPILLS AND LEAKS:
Keep out of sewers & storm water drains & dispose of any leftover material as trade
waste in accordance with local authority guidelines.
DISCLAIMER:
Please Note: Recommendations and advice regarding the use of this product are
to be taken as a guide only. Other than as appears on this products packaging,
Cemix®LTD. does not give any warranty express or implied as to the suitability of
this product for your particular use, because the usage of this product is beyond the
control of Cemix®LTD. If you need advice concerning the use of suitability of this
product for your particular application, please contact Cemix®LTD first. If this product
is defective because of Cemix®LTD’s fault, please contact the supplier or Cemix®
LTD. who will replace it at no cost.