Untitled - Kale Kilit Dış Ticaret

Kale Kilit ve Kalıp Sanayi A.Ş.
www.kalekilit.com.tr
K
CMY
CY
MY
CM
Y
M
C
KD04087-244.pdf
1
07.06.2016
16:58
KALE KİLİT VE KALIP SANAYİ A.Ş
UYUMLU S‹L‹ND‹R T‹PLER‹
‹Ç K‹L‹T UYUMLULUK TABLOSU
UYUMLU S‹L‹ND‹R T‹PLER‹
‹Ç K‹L‹T UYUMLULUK TABLOSU
COMPATIBLE CYLINDER MODELS
COMPATIBLE CYLINDER MODELS
MORTISE HARMONY TABLE
MORTISE HARMONY TABLE
USER MANUEL
Basic functions
One management code (permanent code) and one user code (one time code,
shorted as OTC), which could be minimal 1 and maximal 9 digits in length from
0-9. When it is set more than 9 digits, the lock will sound one beep to remind
the error.
Notice: Every time press the number key, a short “Di” will be sounded and
blue light turns on once.
Initialization
Install 3pcs AA alkaline batteries to power on the lock, and then take off 1pc.
Press the SET button inside battery box and meanwhile install the battery back.
Press the SET button again for several seconds until one beep “Di” sounds
indicating that initialization is completed successfully. In this case, management
code changes to factory default code 123456, and OTC code was cancelled.
Notice: If there is no OTC and management code is 123456 when powered
on the lock, the lock will be in Passage Mode.
Change Management Code
Input
old management code
, if old management code is correct,
2 beeps one short and one long “Di.Di…” will be sounded and blue light turns
, one long “Di” will be sounded
on. Then input new management code
and blue light turns on indicating a successful operation.
To use Management Code
To open the lock: Input
management code
, one long Di… will
be sounded and blue light turns on. Turn handle to open the lock, after that it
will be automatically locked again after 6 seconds, and OTC code is still valid.
To set the lock: open the lock by management code, before it is locked again
in 6 seconds,
• Press “1” for 4 seconds to enter Passage Mode, user can set OTC code in
this mode.
• Press “2” for 4 seconds to enter or cancel Silent Mode.
• Press “3” for 4 seconds to cancel OTC. If the operation time is out, the lock
will be automatically locked.
To use User Code
• In Passage Mode: input
user code
, one long Di… will be
sounded and blue light turns on. Close the door, it will be locked and OTC
is set successfully.
the same user code
, one long Di…
• In locked status: input
will be sounded and blue light turns on.. Turn handle to open the lock, OTC
is cancelled and lock turns to Passage mode.
Notice: When it is double locked by button, User Code can’t open the lock
with indication as one beep “Di”, blue light turns on once and then red light
blinks twice.
Passage Mode
Under the Passage Mode user can open the door by pressing the handle
directly without the code. There are 2 methods to turn the lock to the Passage
Mode;
• Open the lock with the “user code” to make the lock into Passage mode;
• Open the lock with the “permanent code”, then keep pressing the button
“1” in the keypad for 4 seconds to the Passage Mode. At this moment the
old one time code will not be invalid until inputting the new one to open the lock.
Double lock by button
When double locked by button from inside, unlock by Management Code only.
When the lock is closing, the prompt is one “Di” and red light once when
pressing the button from inside. Open it by handle from inside will cancel the
button’s function with the two beeps “Di.Di.”.
In passage mode, pressing the button from inside will come out with one short
and one long Beep “Di.Di….” and red light blinks once. The lock is locked
with “E-Double lock”. Open it by handle from inside will cancel the button’s
function with the two beeps “Di.Di.”. The lock is back to Passage Mode.
Note: The red light blinks every 5 seconds under “E-Double locked”status.
USER MANUEL
Basic functions
One management code (permanent code) and one user code (one time code,
shorted as OTC), which could be minimal 1 and maximal 9 digits in length from
0-9. When it is set more than 9 digits, the lock will sound one beep to remind
the error.
Notice: Every time press the number key, a short “Di” will be sounded and
blue light turns on once.
Initialization
Install 3pcs AA alkaline batteries to power on the lock, and then take off 1pc.
Press the SET button inside battery box and meanwhile install the battery back.
Press the SET button again for several seconds until one beep “Di” sounds
indicating that initialization is completed successfully. In this case, management
code changes to factory default code 123456, and OTC code was cancelled.
Notice: If there is no OTC and management code is 123456 when powered
on the lock, the lock will be in Passage Mode.
Change Management Code
Input
old management code
, if old management code is correct,
2 beeps one short and one long “Di.Di…” will be sounded and blue light turns
, one long “Di” will be sounded
on. Then input new management code
and blue light turns on indicating a successful operation.
To use Management Code
To open the lock: Input
management code
, one long Di… will
be sounded and blue light turns on. Turn handle to open the lock, after that it
will be automatically locked again after 6 seconds, and OTC code is still valid.
To set the lock: open the lock by management code, before it is locked again
in 6 seconds,
• Press “1” for 4 seconds to enter Passage Mode, user can set OTC code in
this mode.
• Press “2” for 4 seconds to enter or cancel Silent Mode.
• Press “3” for 4 seconds to cancel OTC. If the operation time is out, the lock
will be automatically locked.
To use User Code
• In Passage Mode: input
user code
, one long Di… will be
sounded and blue light turns on. Close the door, it will be locked and OTC
is set successfully.
the same user code
, one long Di…
• In locked status: input
will be sounded and blue light turns on.. Turn handle to open the lock, OTC
is cancelled and lock turns to Passage mode.
Notice: When it is double locked by button, User Code can’t open the lock
with indication as one beep “Di”, blue light turns on once and then red light
blinks twice.
Passage Mode
Under the Passage Mode user can open the door by pressing the handle
directly without the code. There are 2 methods to turn the lock to the Passage
Mode;
• Open the lock with the “user code” to make the lock into Passage mode;
• Open the lock with the “permanent code”, then keep pressing the button
“1” in the keypad for 4 seconds to the Passage Mode. At this moment the
old one time code will not be invalid until inputting the new one to open the lock.
Double lock by button
When double locked by button from inside, unlock by Management Code only.
When the lock is closing, the prompt is one “Di” and red light once when
pressing the button from inside. Open it by handle from inside will cancel the
button’s function with the two beeps “Di.Di.”.
In passage mode, pressing the button from inside will come out with one short
and one long Beep “Di.Di….” and red light blinks once. The lock is locked
with “E-Double lock”. Open it by handle from inside will cancel the button’s
function with the two beeps “Di.Di.”. The lock is back to Passage Mode.
Note: The red light blinks every 5 seconds under “E-Double locked”status.
Wrong code alarm
TROUBLE SHOOTING
When inputting the error code or operation delay, the lock will give two beeps
“Di.Di” with red light once and back to standby mode. If inputting the wrong
code 4 times continuously, the lock will give alarms with red and blue lights
keep blinking.
Low voltage alarm
When battery voltage is DC3.6±0.2V, the lock will sound 3 beeps “Di.Di.Di.”
during opening time, indicating that battery voltage is low. Please change
batteries, and 50 times opening remains in this situation.
Switching to Silent Mode
In order to switch into silent mode press 2 for five seconds after entering
permanent code
. Blue light is indicates that lock in silent mode.
Switching to Sound Mode
In order to switch into sound mode press 2 for five seconds after entering
permanent code
. Hearing beep sound is indicates that lock in sound
mode.
2. In Silent mode.
Wrong code alarm
TROUBLE SHOOTING
When inputting the error code or operation delay, the lock will give two beeps
“Di.Di” with red light once and back to standby mode. If inputting the wrong
code 4 times continuously, the lock will give alarms with red and blue lights
keep blinking.
Low voltage alarm
When battery voltage is DC3.6±0.2V, the lock will sound 3 beeps “Di.Di.Di.”
during opening time, indicating that battery voltage is low. Please change
batteries, and 50 times opening remains in this situation.
Switching to Silent Mode
In order to switch into silent mode press 2 for five seconds after entering
permanent code
. Blue light is indicates that lock in silent mode.
Switching to Sound Mode
In order to switch into sound mode press 2 for five seconds after entering
permanent code
. Hearing beep sound is indicates that lock in sound
mode.
2. In Silent mode.
KALE KİLİT VE KALIP SANAYİ A.Ş
Atatürk Caddesi Başaklı Sokak No:24
34610 Güngören İstanbul - TÜRKİYE
+90 (212) 705 80 00
+90 (212) 705 79 77
Şifreli Kilit Lüks Seri
87-260
www.kalekilit.com.tr
KALE KİLİT VE KALIP SANAYİ A.Ş
Supply Chain Director
Halil İbrahim Aygündüz
Atatürk Caddesi Başaklı Sokak No:24
34610 Güngören İstanbul - TÜRKİYE
+90 (212) 705 80 00
+90 (212) 705 79 77
Keypad Lock
87-260
www.kalekilit.com.tr
Tedarik Zinciri Direktörü
Halil İbrahim Aygündüz
KALE KİLİT VE KALIP SANAYİ A.Ş
Atatürk Caddesi Başaklı Sokak No:24
34610 Güngören İstanbul - TÜRKİYE
+90 (212) 705 80 00
+90 (212) 705 79 77
Şifreli Kilit Lüks Seri
87-260
www.kalekilit.com.tr
KALE KİLİT VE KALIP SANAYİ A.Ş
Supply Chain Director
Halil İbrahim Aygündüz
Atatürk Caddesi Başaklı Sokak No:24
34610 Güngören İstanbul - TÜRKİYE
+90 (212) 705 80 00
+90 (212) 705 79 77
Keypad Lock
87-260
www.kalekilit.com.tr
Tedarik Zinciri Direktörü
Halil İbrahim Aygündüz
Kale Kilit ve Kalıp Sanayi A.Ş.
www.kalekilit.com.tr