LED - Lighting and connection technology Lampholder for E

Transcription

LED - Lighting and connection technology Lampholder for E
NEW
LED - Lighting and connection technology
Lampholder for E-CORE GH76p LED Light Engine from
LED
Your Connection to Light
Lampholder for E-CORE GH76p
LED Light Engine from Toshiba
In close co-operation with Toshiba,
Japan‘s leading lamp manufacturer, the
lampholder 28.301 was developed for
use with the new E-CORE GH76p LED
Light Engine. This system, consisting
of lampholder and LED-Module,
is suitable for all types of compact
applications, for example downlights.
Assembly to a heat sink is simply done
with just three screws.
The LED-Module can then be inserted
and easily exchanged, just like a
conventional lamp. With a quarter turn
the Module clicks into place and at
the same time the base of the Module
makes firm contact with the heat sink,
ensuring good heat dissipation. Wire
connection is achieved by tried and
tested push wire technology.
Heat sink
BJB Lampholder
E-CORE GH76p LED Light Engine
28.301
LED - Lighting and connection technology
Lampholder for E-Core LED Light Engines from Toshiba
pkg.
wt.
part-no.
125
20 g
28.301.1002.90
Screw fixing
• Key: GH76p-II for 220-277 V AC
• Material: PPS
• Lampholder is delivered fully assembled with M3
fixing screws included.
• Screw fixing holes M3 recommendation: sharp-edged
without countersink
• Torque recommendation: 0.5 - 0.6 Nm
• Screws are equipped with a one time loosening protection. After disassembly and a second assembly,
the user is responsible for loosening protection.
Marking of contacts:
1. Neutral
2. Phase
3. Dim
4. Dim
5. Functional ground
0.5 - 0.75 mm2 0.5 - 0.75 mm2
pkg.
wt.
part-no.
125
20 g
28.301.1001.90
Screw fixing
• Key: GH76p-I for 100-120 V AC
• Material: PPS
• Lampholder is delivered fully assembled with M3
fixing screws included.
• Screw fixing holes M3 recommendation: sharp-edged
without countersink
• Torque recommendation: 0.5 - 0.6 Nm
• Screws are equipped with a one time loosening protection. After disassembly and a second assembly,
the user is responsible for loosening protection.
Marking of contacts:
1. Neutral
2. Phase
3. Dim
4. Dim
5. Functional ground
0.5 - 0.75 mm2 0.5 - 0.75 mm2
Symbols
03‑2011
Single push wire terminals
For solid conductors
within the cross sectional
range stated
Rating
CAD-data available
This page is only valid in connection with the general information and notes of the comples catalogue, issue 2008-2011
For tinned wire ends
within the cross sectional
range stated
BJB GmbH & Co. KG · Werler Str. 1 · 59755 Arnsberg · Germany
Telephone +49 2932 982-0 · Fax +49 2932 982-8201
[email protected] · www.bjb.com
Your Connection to Light

Similar documents

Brochure HID lampholders GU8.5

Brochure HID lampholders GU8.5 Due to this, the lampholder has a circular collar which makes the insertion of the lamp base easier and provides easy replacement of the lamp, even in recessed applications. This solid ceramic vers...

More information

Reduce costs and benefit from the very best in lighting

Reduce costs and benefit from the very best in lighting Shade ring, Thread 40 x 2.5 mm Screw fixing Material: Globe: Glass Shade Ring: PC

More information