rollup 03

Transcription

rollup 03
rollup 03
Silver: RU-S3-S-4
Black: RU-S3-B-4
The Rollup 03 is a single-sided retractable banner stand that is simple,
easy to assemble and combines quality, elegance and value. It comes with
a hybrid bungee/ telescoping pole and comes in an anodized silver finish.
features and benefits:
- Variable graphic height: 60.5” - 83.25”
- Hybrid bungee/ telescoping pole with toolless quick rail
- Adjustable feet on base
- Supplied with a padded carry bag with strap
- Available in anodized silver or black
finish
- Molded end plates
- Lifetime limited warranty against
manufacturer defects
dimensions:
Hardware
Graphic
Assembled unit:
32.68”(w) x 84.75”(h) x 7.08”(d) approx.
830mm(w) x 2153mm(h) x 180mm(d) approx.
Refer to graphic template for more
information.
Base dimensions:
32.68”(w) x 3.15”(h) x 7.08”(d) approx.
830mm(w) x 80mm(h) x 180mm(d) approx.
WARNING: Always attach graphic to base
and top rail before removing the locking pin.
After fitting, the graphic should be left for
24 hours before use to ensure the adhesive
bonds sufficiently. Opening the base will
invalidate the product warranty.
Shipping
Shipping dimensions - ships in one box
38”(l) x 9”(h) x 5”(d)
965mm(l) x 229mm(h) x 127mm(d)
Approximate shipping weight: without graphic
11 lbs/ 4.9 kg
Hybrid pole
additional information:
Graphic materials:
anti-curl vinyl, premium opaque
fabric, melinex
LV4 banner lighting option available
Carry bag included
banner stands
03.01.16 © Nimlok Display and Exhibit Solutions Worldwide
For questions contact your local Nimlok distributor
Set-up
Assemble three piece bungee pole
1
Secure pole(s) in the base of stand
2
Gently lean the unit back and pull
the graphic up by the toprail
3
Leveling feet located under unit
4
Graphic to top rail attachment (metal attachment)
metal insert
metal insert
metal insert
Loosen each screw from the rail
using provided allen key and remove
metal insert (do not remove screws)
1
Peel film to expose adhesive; place
metal insert from graphic rail on top
back side of the graphic point
2
Press down on the metal insert to
make sure adhesive is secure on
graphic
3
Insert the metal insert with
graphic attached into the top
graphic profile rail
4
Quick slide top rail attachment (plastic insert)
top slider
printed
side
down
Tighten the screws back in place
to hold metal insert and graphic
with allen key
5
Remove top slider from graphic rail
1
Remove film to expose adhesive on
top slider
2
Align and apply to top slider on the
top front of graphic
3
Graphic to base attachment
Insert graphic onto graphic rail
4
Line the bottom of the back of
graphic print with adhesive tape on
white leader strip
Remove pin while holding onto the
graphic so the graphic does not
retract back in quickly
4
Slowly retract the graphic
back into the base
graphic back
graphic front
top rail slider
1
5
Once aligned pull adhesive tape
slowly while applying pressure to
graphic to adhere tape
2
Place in additional masking tape
to the back of the graphic for extra
protection
3
check out these related products:
rollup 01
rollup 02
rollup 03
rollup 04
rollup 05
rollup 06
rollup DS 01
rollup DS 02
smart banner 01
smart banner 02
We continue to improve and modify our product range and reserve the right to vary the specifications without prior notice. All dimensions
and weights quoted are approximate and we accept no responsibility for variance. E&OE. See Graphic Templates for graphic bleed specifications.

Similar documents

rollup 01

rollup 01 Add lights to any of our banner stands. LV4 is recommended. Graphic materials: 11 mil. UV printed supreme melanex premium 100% opaque fabric 14 oz. solvent printed anti-curl vinyl

More information

smart banner 02

smart banner 02 17 lbs / 7.66 kg shipping weight without graphic approx.

More information

smart banner 01

smart banner 01 After fitting, the graphic should be left for 24 hours before use to ensure the adhesive bonds sufficiently. Opening the base will void the product warranty. Add lights to any of our banner stands....

More information