Tool and Equipment

Transcription

Tool and Equipment

Manual No. 165A
Revision 17
61-00-65
December 2014
Illustrated
Tool and Equipment
Manual
Hartzell Propeller Inc.
One Propeller Place
Piqua, Ohio 45356-2634 U.S.A.
Phone: 937.778.4200
Fax: 937.778.4391
TOOL AND EQUIPMENT MANUAL
165A
© 1995, 1996, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2011, 2012, 2013, 2014 - Hartzell Propeller Inc. All rights reserved
COVER
61-00-65
Page 2
Rev. 17 Dec/14
165A
REVISION 17 HIGHLIGHTS
•COVER
• Revised to match the manual revision
• REVISION HIGHLIGHTS
• LIST OF EFFECTIVE PAGES
• TABLE OF CONTENTS
• INTRODUCTION
• Added vendors
• TOOL AND EQUIPMENT INDEX
• TOOL AND EQUIPMENT LIST
• Name change from Hartzell to Hartzell Propeller Inc., as applicable, is marked with
a revision bar but not listed below.
• Revised Mahr Federal Inc. (MF) to Mahr Federal Inc. (MH), as applicable, is marked
with a revision bar but not listed below.
• Revised Torque Wrench Adaptor discriptions
• Added TE551, Torque Wrench Adaptor
• Added Profilometer MarSurf PS1 6910214
• Revised AST-3475, Profilometer to add MarSurf PS1 6910214 Tool and Illustration
• Added TE550, "F" Flange Spindle
• Added Erosion Shield References to the Fit Check Tools
• Revised the blade for TE340, Fit Check Tool
• Added TE552 thru TE558, Fit Check Tools
• Revised TE465 and TE466, Template description
• Revised TE403, Reamer description
• Revised TE438, Blade Pitch Fixture illustration
• Added TE550, "F" Flange Bantam Adapter Ring
• Added TE559, Right Angle Grease Coupler
REVISION HIGHLIGHTS
61-00-65
Page 1
Rev. 17 Dec/14
165A
REVISION 17 HIGHLIGHTS
1. Introduction
A.General
(1) This is a list of current revisions that have been issued against this manual.
Please compare to RECORD OF REVISIONS page to ensure that all revisions
have been added to the manual.
B.Components
(1) Revision No. indicates the revisions incorporated in this manual.
(2) Issue Date is the date of revision.
(3) Comments indicates the level of the revision.
(a) New Issue is a new manual distribution. The manual is distributed in its
entirety. All the revision dates are the same and no change bars are used.
(b) Reissue is a revision to an existing manual that includes major content
and/or major format changes. The manual is distributed in its entirety. All
the revision dates are the same and no change bars are used.
(c) Major Revision is a revision to an existing manual that includes major
content or minor format changes over a large portion of the manual. The
manual is distributed in its entirety. All the revision dates are the same, but
change bars are used to indicate the changes incorporated in the latest
revision of the manual.
REVISION HIGHLIGHTS
61-00-65
Page 2
Rev. 17 Dec/14
165A
(d) Minor Revision is a revision to an existing manual that includes minor
content changes to the manual. Only the revised pages of the manual are
distributed. Each page retains the date and the change bars associated
with the last revision to that page.
Revision No.
Original
Revision 1
Revision 2
Revision 3
Revision 4
Revision 5
Revision 6
Revision 7
Revision 8
Revision 9
Revision 10
Revision 11
Revision 12
Revision 13
Revision 14
Revision 15
Revision 16
Revision 17
Issue Date
Comments
Nov/95
Aug/96
May/98
Jan/99
Oct/99
Apr/00
May/01
Aug/01
Mar/02
Jun/02
Sep/03
Aug/04
Aug/11
Jul/12
Jun/13
Dec/13
Apr/14
Dec/14
Total rewrite
Minor Revision
Minor Revision
Minor Revision
Minor Revision
Minor Revision
Minor Revision
Minor Revision
Minor Revision
Minor Revision
Minor Revision
Minor Revision
Major Revision
Minor Revision
Minor Revision
Minor Revision
Minor Revision
Minor Revision
REVISION HIGHLIGHTS
61-00-65
Page 3
Rev. 17 Dec/14
165A
(This page is intentionally blank.)
REVISION HIGHLIGHTS
61-00-65
Page 4
Rev. 17 Dec/14
165A
RECORD OF REVISIONS
This is a permanent historical record of revisions inserted into this manual.
Revision 12 includes all prior revisions, up to and including Revision 11.
Revision
Number
Issue
Date
Date
Inserted
Inserted
By
12
Aug/11
Aug/11
HPI
13
Jul/12
Jul/12
HPI
14
Jun/13
Jun/13
HPI
15
Dec/13
Dec/13
HPI
16
Apr/14
Apr/14
HPI
17
Dec/14
Dec/14
HPI
Revision
Number
RECORD OF REVISIONS
Issue
Date
Date
Inserted
61-00-65
Inserted
By
Page 1
Rev. 12 Aug/11
165A
RECORD OF REVISIONS
This is a permanent historical record of revisions inserted into this manual.
Revision 12 includes all prior revisions, up to and including Revision 11.
Revision
Number
Issue
Date
Date
Inserted
Inserted
By
Revision
Number
RECORD OF REVISIONS
Issue
Date
Date
Inserted
61-00-65
Inserted
By
Page 2
Rev. 12 Aug/11
165A
RECORD OF TEMPORARY REVISIONS
Update this page to show all temporary revisions inserted into this manual.
Revision 12 includes all prior temporary revisions, up to and including TR-008.
Temporary
Revision No.
Section/
Page
Issue
Date
Date
Inserted
Inserted
By
Date
Removed
Removed
By
TR-009
4-43
Oct/11
Oct/11
HPI
Jul/12
HPI
TR-011
4-65
May/12
May/12
HPI
Jul/12
HPI
TR-010
4-14
Nov/11
Nov/11
HPI
TR-012
4-136
Oct/12
Oct/12
HPI
TR-014
4-149
Mar/14
Mar/14
HPI
TR-013
4-144
Sep/13
Sep/13
HPI
Jul/12
Jun/13
Dec/13
Apr/14
61-00-65
HPI
HPI
HPI
HPI
Page 1
Rev. 12 Aug/11
165A
Update this page to show all temporary revisions inserted into this manual.
Revision 12 includes all prior temporary revisions, up to and including TR-008.
Temporary
Revision No.
Section/
Page
Issue
Date
Date
Inserted
Inserted
By
Date
Removed
61-00-65
Removed
By
Page 2
Rev. 12 Aug/11
165A
LIST OF EFFECTIVE PAGES
Chapter
Page
Revision Level
Date
Cover/Cover Back
Cover/Inside Cover
Rev. 17
Dec/14
Revision Highlights
1 thru 4
Rev. 17
Dec/14
Record of Revisions
1 and 2
Rev. 12
Aug/11
Record of Temporary Revisions
1 and 2
Rev. 12
Aug/11
List of Effective Pages
1 thru 4
Rev. 17
Dec/14
Table of Contents
1 and 2
Rev. 17
Dec/14
Introduction
1 and 2
Rev. 17
Dec/14
Introduction
3Rev. 13
Jul/12
Introduction
4 thru 10Rev. 17
Dec/14
Numerical Index
1-1 and 1-2
Rev. 12
Aug/11
Tool and Equipment Index
2-1
Rev. 15
Dec/13
Tool and Equipment Index 2-2 thru 2-4
Rev. 12
Aug/11
2-5
Rev. 14
Jun/13
2-6 and 2-7
Rev. 12
Aug/11
2-8
Rev. 15
Dec/13
2-9
Rev. 12
Aug/11
2-10
Rev. 16
Apr/14
2-11
Rev. 17
Dec/14
2-12
Rev. 15
Dec/13
2-13
Rev. 17
Dec/14
2-14 thru 2-16
Rev. 15
Dec/13
2-17 and 2-18
Rev. 17
Dec/14
Alphabetical Index
3-1 and 3-2
Rev. 12
Aug/11
Tool and Equipment List
4-1 thru 4-5
Rev. 12
Aug/11
4-6
Rev. 17
Dec/14
4-7
Rev. 14
Jun/13
4-8 and 4-9
Rev. 12
Aug/11
4-10
Rev. 15
Dec/13
4-11
Rev. 12
Aug/11
4-12 and 4-13
Rev. 15
Dec/13
61-00-65
Page 1
Rev. 17 Dec/14
165A
Chapter
Page
Revision Level
Date
4-14Rev. 13
4-15
Rev. 17
Dec/14
4-16 thru 4-23
Rev. 12
Aug/11
4-24
Rev. 15
Dec/13
4-25
Rev. 12
Aug/11
4-26
Rev. 17
Dec/14
4-27 thru 4-30
Rev. 12
Aug/11
4-31
Rev. 15
Dec/13
4-32 thru 4-36
Rev. 12
Aug/11
4-37
Rev. 14
Jun/13
4-38Rev. 15
Dec/13
4-39
4-40 and 4-41
4-42
Rev. 17Dec/14
4-43
Rev. 13
Jul/12
4-44 thru 4-57
Rev. 12
Aug/11
4-58
Rev. 15
Dec/13
4-59 and 4-60
Rev. 12
Aug/11
4-61 and 4-62
Rev. 15
Dec/13
4-63 and 4-64
Rev. 12
Aug/11
4-65
Rev. 15
Dec/13
4-66 thru 4-69
Rev. 12
Aug/11
4-70 and 4-71
Rev. 15
Dec/13
4-72 thru 4-74
Rev. 12
Aug/11
4-75
4-76 thru 4-78
Rev. 12
Aug/11
4-79
Rev. 17
Dec/14
4-80
Rev. 12
Aug/11
4-81 and 4-82
Rev. 15
Dec/13
4-83 and 4-84
Rev. 12
Aug/11
Jul/12
Rev. 17Dec/14
Rev. 12
Aug/11
Rev. 17Dec/14
61-00-65
Page 2
Rev. 17 Dec/14
165A
Chapter
Page
Revision Level
Date
4-85 thru 4-87
Rev. 15
Dec/13
4-88 thru 4-90
Rev. 12
Aug/11
4-91
Rev. 15
Dec/13
4-92 thru 4-94
Rev. 12
Aug/11
4-95
Rev. 15
Dec/13
4-96 thru 4-99
Rev. 12
Aug/11
4-100
Rev. 15
Dec/13
4-101 thru 4-102
Rev. 12
Aug/11
4-103
Rev. 16
Apr/14
4-104 thru 4-113
Rev. 12
Aug/11
4-114
Rev. 15
Dec/13
4-115 and 4-116
Rev. 12
Aug/11
4-117 thru 4-119
Rev. 15
Dec/13
4-120 and 4-121
Rev. 12
Aug/11
4-122
Rev. 16
Apr/14
4-123 and 4-124
Rev. 12
Aug/11
4-125
Rev. 15
Dec/13
4-126 and 4-127
Rev. 12
Aug/11
4-128
Rev. 15
Dec/13
4-129 thru 4-133
Rev. 12
Aug/11
4-134 and 4-135
Rev. 17
Dec/14
Tool and Equipment List4-136
Rev. 13
Jul/12
4-137 thru 4-143
Rev. 14
Jun/13
4-144 thru 4-147
Rev. 15
Dec/13
4-148
Rev. 16
Apr/14
4-149 and 4-150
Rev. 15
Dec/13
4-151 and 4-152
Rev. 16
Apr/14
4-153 and 4-154
Rev. 17
Dec/14
61-00-65
Page 3
Rev. 17 Dec/14
165A
61-00-65
Page 4
Rev. 17 Dec/14
165A
TABLE OF CONTENTS
Page
REVISION HIGHLIGHTS..................................................................................................1
RECORD OF REVISIONS................................................................................................1
RECORD OF TEMPORARY REVISIONS.........................................................................1
LIST OF EFFECTIVE PAGES...........................................................................................1
TABLE OF CONTENTS.....................................................................................................1
INTRODUCTION...............................................................................................................1
1. Using the Illustrated Tool and Equipment Manual..................................................3
A.General.............................................................................................................3
B. Vendor...............................................................................................................4
C. Page..................................................................................................................9
2. Using the “TE” Reference Number.........................................................................9
3. Ordering Parts........................................................................................................9
NUMERICAL INDEX......................................................................................................1-1
TOOL AND EQUIPMENT INDEX...................................................................................2-1
ALPHABETICAL INDEX.................................................................................................3-1
TOOL AND EQUIPMENT LIST.......................................................................................4-1
TABLE OF CONTENTS
61-00-65
Page 1
Rev. 17 Dec/14
165A
TABLE OF CONTENTS
61-00-65
Page 2
Rev. 17 Dec/14
165A
INTRODUCTION - CONTENTS
1. Using the Illustrated Tool and Equipment Manual..................................................3
A.General.............................................................................................................3
B. Vendor...............................................................................................................4
C. Page..................................................................................................................9
2. Using the “TE” Reference Number.........................................................................9
3. Ordering Parts........................................................................................................9
INTRODUCTION
61-00-65
Page 1
Rev. 17 Dec/14
165A
INTRODUCTION
61-00-65
Page 2
Rev. 17 Dec/14
165A
INTRODUCTION
1. Using the Illustrated Tool and Equipment Manual
A.General
(1) This manual contains the tooling and equipment required to perform standard
procedures in accordance with Hartzell Propeller Inc. manuals.
(2) In addition to an illustration of each item, the following information is provided:
(a) The title or description
(b) The part number
1
The part number listed should be used when ordering the item from
Hartzell Propeller Inc. or a Hartzell Propeller Inc. approved distributor.
(c) The TE number
1
The number given to the tool that is used to reference the tool in
Hartzell Propeller Inc. publications.
(d) A description of the item, including:
1
Its uses and other related items needed to perform the task
2
A breakdown of subcomponents, as necessary
3
Information required to fabricate the item, if applicable
4
Additional vendors where the item may be purchased, as necessary.
(3) Some of the parts may be purchased through Hartzell Propeller Inc. Refer to
the specific tool for information about the Hartzell Propeller Inc. part number.
(4) Tool and Equipment Index
(a) The Tool and Equipment Index of this Tool and Equipment Manual is a list
of the tools by TE number that are included in this manual and the page
number on which the tool illustration and information may be found.
1
For a tool that shows more than one page number in the index,
generally the first page number is where the most comprehensive
information about the tool may be found. The additional page
numbers given are other places in the manual where the tool is
referenced.
(b) The Tool and Equipment Index of this Tool and Equipment Manual uses a
number of abbreviations. Refer to the sections "Vendor" and "Application"
in this chapter for a list of the abbreviations used.
INTRODUCTION
61-00-65
Page 3
Rev. 13 Jul/12
165A
B. Vendor
The vendor is the point of purchase of the item for the end user:
AE
All Phase Electric Supply Co............. Direct from the Vendor.
750 W. Leffel Lane.
Springfield, OH 45501
Tele: 937-323-7555
Fax: 937-325-0838
Email: [email protected]
www. all-phase-springfield.shopced.com
AF
American Forge & Foudnery, Inc....... Direct from the Vendor
PO. Box 59
Guilderland Center, NY 12085
Tele: 518-861-0101
Toll Free: 800-255-0555
Fax: 518-861-0099
www.affjaxx.com
AL
ALATEC Products Corp..................... Direct from the Vendor.
12109 Bridgeton Square Drive
Brigton, MO 63044
AP
APEX Products.................................. From any Distributor.
Division of Cooper Tools
P.O. Box 952
Dayton, OH 45401
AR
Associated Research......................... From any Distributor.
905 Carriage Park Avenue
Lake Bluff, IL 60044
Tele: 800.858.8378
BD
........................................................... Contact any Bearing Distributor.
BHBondhus............................................. From any Distributor.
1400 East Broadway
Monocello, MN 55362
BK
BK Precision...................................... Direct from the Vendor.
3033 South Kettering Blvd.
Dayton, OH 45439-1948
Tele: 937.294.8980
Fax: 937.294.2517
BN
Branson Ultrasonics Corporation....... Direct from the Vendor.
41 Eagle Road
Danbury, CT 06813-1961
Tele: 800.732.9262
Fax: 203.796.2240
INTRODUCTION
61-00-65
Page 4
Rev. 17 Dec/14
165A
BR
BriskHeat Corporation........................ Direct from the Vendor or Hartzell Propeller Inc.
P.O. Box 163309
Columbus, OH 43216-3309
Tele: 800.848.7673
CG
Clay-Groomer Machine Shop, Inc...... Direct from the Vendor or Hartzell Propeller Inc.
701 S. Carlton Ave.
Farmington, NM 87401
Tele: 505.327.7751
CL
Clemco Industries Corp..................... Direct from the Vendor.
One Cable Car Drive
Washington, MO 63090
Tele: 636.239.8172
CP
Cole Palmer....................................... Direct from the Vendor or Distributor.
7425 N. Oak Park Avenue
Chicago, IL 60648
CS
Customer Supplied............................ Locally fabricated by the end user.
Information required to purchase or fabricate
the unit will be found in the description.
DM
Daniels Manufacturing Corp.............. Direct from the Vendor or Distributor.
526 Thorpe Road
Orlando, FL 32824-8133
EP
Everhard Products............................. Direct from the Vendor.
1016 Ninth Street, SW
Canton, OH 44707
Tele: 216.453.7786
GO
George Olcott Co............................... Direct from the Vendor.
P.O. 783
Scottsboro, AL 35768
Tele:256.259.4937
Fax:256.259.4942
HE
Heli-Coil Division................................ Direct from the Vendor.
Emhart Fastening Systems Group
Shelter Rock Lane
Danbury, CT 06810
Tele: 203.743.7651
Fax: 203.798.2540
HM
Hemco Corp....................................... Direct from the Vendor.
455 Douglas Avenue
Holland, MI 49424
Tele: 616.396.4604
HP
Hartzell Propeller Inc.......................... Any Hartzell Propeller Inc. approved Distributor.
INTRODUCTION
61-00-65
Page 5
Rev. 17 Dec/14
165A
HK
Hocking NDT Ltd................................ Direct from the Vendor.
50 Industrial Park Road
Lewistown, PA 17044
Tele:717.242.0320
Fax:717.242.4170
JC
Jay Instrument and Spec Co.............. Direct from the Vendor.
555 North Wayne Avenue
Cincinnati, Ohio 45215
KE
Keithley Instruments, Inc.................... Direct from the Vendor.
28775 Aurora Road
Solon, OH 44139
Tele: 800.348.3735
Fax: 440.498.2980
LC
Leschen Wire Rope........................... From any Distributor.
St. Joseph, MO 64502
LE
Lee Valve Company........................... Direct from the Vendor.
9701 W. Higgins Road
Suite 380
Rosemont, IL 60018
LI
Lincoln Industrial Corporation............ Direct from the Vendor
4130 Tumwater Truck Route
Port Angeles, WA 98363
Tele: 360-457-6122
Fax: 360-452-4773
www.lincolnindustrialcorp.com/
MA Matco Tools........................................ Direct from the Vendor
4403 Allen Road
Stow, OH 44224
Tele: 866-289-8665
Fax: 330-926-5323
www.matcotools.com
MC
McMaster-Carr Supply Co................. Direct from the Vendor.
P.O. Box 4355
Chicago, IL 60680
MF
Magnaflux Corp.................................. Direct from the Vendor.
7300 W. Lawrence Avenue
Chicago, IL 60656
MH
Mahr Federal Inc................................ Either through the Hartzell Propeller Inc.
1144 Eddy Street
distributor network, or it may be purchased
P.O. Box 9400
directly from the vendor.
Providence, RI
Tele:401.784.3100
Fax: 401.784.3246
INTRODUCTION
61-00-65
Page 6
Rev. 17 Dec/14
165A
MS
Mausner Equipment Company, Inc.... Direct from the Vendor.
651 Pierce Place
East Meadow, NY 11554
Tele: 516.481.1600
MT
Mitutoyo America Corporation............ Direct from the Vendor.
965 Corporate Blvd.
Aurora, IL 60504
Tele:630.820.9666
Fax: 630.820.2614
E-mail:[email protected]
OL
Olympus NDT Inc. ............................. Direct from the Vendor
9 Woerd Ave.
Waltham MA, USA
www.olympus-ims.com
Tele: 1-800-225-8330
OT
OTC Tools Inc.................................... Direct from the Vendor
Bosch Automotive Service Solutions
28635 Mound Road
Warren, MI 48092
Tele: 800-533-6127
Fax: 800-283-8665
www.otctools.com
International
Tele: 507-455-7223
Fax: 507-455-7063
PM
Panametrics, Inc................................ Direct from the Vendor.
221 Crescent Street
Waltham, MA 02154
RC
Related Components Inc................... From any Distributor.
3186 Plainfield Road
Dayton, OH 45432
Tele: 937.253.6116
SA
Steinel America.................................. Direct from the Vendor.
9051 Lyndale Ave., South
Bloomington, MN 55420
Tele: 612.888.5950
INTRODUCTION
61-00-65
Page 7
Rev. 17 Dec/14
165A
SM Steelman Pro..................................... Direct from the Vendor
JS Products, Inc.
6445 Montessouri Street
Las Vegas, NV 89113
Tele: 702-362-7011
Toll Free: 800-255-7011
Fax: 775-898-8773
www.steelmanpro.com
SO
Snap-On Tools Corp.......................... Either through the Hartzell Propeller Inc.
P.O. Box 14003
Fairfield, OH 45014
distributor network, or it may be purchased
directly from the vendor.
SP
SAE Products..................................... Direct from the Vendor
1709 Husted Road
Suite #4
Conway, SC 29526
Toll Free: 800-588-8480
Fax: 843-349-0738
www.saeproducts.com
ST
Starrett Tool Co.................................. Direct from the Vendor or Distributor.
Athol, MA 01331
TM
Thexton Manufacturing Company...... Direct from the Vendor
6539 Cecilia Circle
Edina, MN 55439
Tele: 952-831-4171
Toll Free: 800-328-6277
Fax: 952-831-5938
www.thexton.com
VK
Van Keuren........................................ Direct from the Vendor.
107 SCT Drive
White House, TN 37188
Tele: 847.439.9220
VR
VWR Scientific................................... Direct from the Vendor.
P.O. Box 66929
Chicago, IL 60666
WI
Wahl Instruments, Inc........................ Direct from the Vendor.
5750-A Hannum Ave.
Culver City, CA 90231
Tele: 800.344.9245
WH
White Hawk Machine & Tool.............. Direct from the Vendor.
6008 Highway 66
Greenville, TX 75402
Tele: 903.450.1060
INTRODUCTION
61-00-65
Page 8
Rev. 17 Dec/14
165A
C. Page
(1) The item is located on the page number listed in the Page column.
2. Using the “TE” Reference Number
A. In other Hartzell Propeller Inc. publications, tooling references appear with the prefix
“TE” directly following the tool name to which they apply.
(1) For example, a template which is reference number 133 will appear as:
template TE133.
3. Ordering Parts
A. When ordering vendor tooling from the vendor or a distributor, use the number as
specified in the manual.
B. For some vendor tooling there is an associated Hartzell Propeller Inc. part
number. This part number may be used when ordering the tooling direct from
INTRODUCTION
61-00-65
Page 9
Rev. 17 Dec/14
165A
INTRODUCTION
61-00-65
Page 10
Rev. 17 Dec/14
165A
The Numerical Index has been replaced by the Tool and Equipment Index.
Refer to the Tool and Equipment Index in this manual.
NUMBERICAL INDEX
61-00-65
Page 1-1
Rev. 12 Aug/11
165A
NUMERICAL INDEX
61-00-65
Page 1-2
Rev. 12 Aug/11
165A
TE
NUMBER
PART NUMBER
DESCRIPTION
VENDOR
PAGE
HP
HP
HP
HP
HP
HP
TE1
TE2
TE3
TE4
TE5
TE6
TE7
TE8
TE9
TE10
TE11
BST-2912-8
BST-2912-9
BST-3035
BST-2912-4
AST-2877
BST-2837
BST-10008
CST-2919
BST-2853
CST-3021
BST-2823
Adaptor
Adaptor
Adaptor
Adaptor Ring
Torque Wrench Adaptor
PCU Tester - Obsolete
Balance Arbor
Assembly Tool
Dual Acting Propeller Assembly Bench
Spinner Mounting Plate Bender
CS
HP
HP
CS
TE12
CT-1311
Shot Peen Cabinet
CS
TE13
TE14
TE15
TE16
TE17
TE18
TE19
TE20
TE21
TE22
TE23
BST-2942
BST-2943
BST-2944
BST-2945
AST-2803
CST-2923
CST-2924
CST-2925
CST-2926
CST-2989
DST-10014
Shank Protection Cap
Ring Centering Tool
Optical Comparator Overlay
Synchrophaser Check Box
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
OBS
4-26,4-99
4-47,4-92
4-26,4-99
4-6
4-19
OBS
4-87
4-2,4-8
4-91
4-17
4-64,4-65,
4-126
4-31
4-31
4-31
4-31
4-2
4-88
4-88
4-88
4-88
4-88
4-101
TE24
CST-2800
Blade Retention Components Clamp
CS
4-83
TE25
TE26
TE27
TE28
TE29
TE30
TE31
TE32
TE33
TE34
TE35
TE36
TE37
TE38
TE39
TE40
TE41
CST-2929
BST-3038
AST-2870
CUST. P/N
AT-725-1
BST-2826
BST-2826-1
CST-3016
SCO38
SC040
SC042
SC048
SC052
SC056
SC060
BST-3027
BST-3030
Control Rod Alignment Tool
Hub Bearing Radius Comparator
Optical Comparator
Spring Compressor
Spring Compressor Assembly
Portable Spring Compressor
Crowfoot 1 3/16 inch
Crowfoot 1 1/4 inch
Crowfoot 1 5/16 inch
Crowfoot 1 1/2 inch
Crowfoot 1 5/8 inch
Crowfoot 1 3/4 inch
Crowfoot 1 7/8 inch
Modified Crowfoot
Modified Crowfoot
CS
HP
HP
CS
HP
HP
HP
HP
SO
SO
SO
SO
SO
SO
SO
HP
HP
4-88
4-48,4-92
4-5
4-110
4-9
4-18
4-19
4-91,4-85
4-113
4-113
4-113
4-113
4-113
4-113
4-113
4-44,4-92
4-45,4-92
TOOL AND EQUIPMENT INDEX
61-00-65
Page 2-1
Rev. 15 Dec/13
165A
TE
NUMBER
PART NUMBER
DESCRIPTION
VENDOR
PAGE
TE42
TE43
TE44
TE45
TE46
TE47
TE48
TE49
TE50
TE51
BST-3031
BST-3033
170-1/4
n/a
BST-3060-1
YA484
CT-1075
BT-1312
BST-5845
BST-2920
Modified Crowfoot
Modified Crowfoot
Apex Torqset Bit
n/a
Screw Driver
Tool Box
Adjustable Riser Fixture
Almen Strip Fixture
Chamfering Tool
Drill Fixture
HP
HP
AP
n/a
HP
SO
HP
HP
HP
HP
4-45,4-92
4-46,4-92
4-113
n/a
4-55
4-93
4-95
4-65,4-95
4-58
4-27
TE52
CST-2913
Pilot Tube Press Fixture
HP
4-84,4-57
TE53
TE53-1
TE53-2
TE54
TE55
TE56
TE57
TE58
DT-336
DT-336+6
DT-336+7
BST-2892
BST-2892-1
BST-2892-2
BST-2908
BST-10006
Pilot Tube Removal Fixture
Jaw
Jaw
Piston Fixture HC-B3( )30-2E
Piston Fixture All #20 Spline
Piston Fixture HC-B3( )30-2B
Piston Fixture ( )HC-A3VF-4 and HC-B3WF-4
Rigging Cover
HP
HP
HP
HP
HP
HP
HP
HP
TE59
CST-2914
Spring Compressor Fixture
HP
4-102,4-21
4-102
4-102
4-23
4-23
4-23
4-24
4-61,4-92
4-85,4-22,
4-23,4-24
TE60
BST-2812
Counterweight Clamp Gauge
HP
4-16
TE61
TE62
TE63
TE64
TE64-1
TE65
TE66
TE66-1
TE66-2
TE67
TE68
TE68-1
TE68-3
TE68-4
TE68-5
TE68-6
TE68-7
TE68-8
TE68-9
BST-2964
BST-2958L
BST-3036
BST-2985
BST-2985-1
AST-2849
7552-4/791975524
7552-5/791975525
7552-7/791975527
KHT9000-9
BST-3047
BST-3047-8
BST-3047-3
BST-3047-4
BST-3047-5
BST-3047-6
BST-3047-7
BST-3047-2
BST-3047-1
Thickness Gauge
Hoist Ring Combo
Piston Installation Cone
Bearing Installation Tool
Beta Rod Retainer Installation Tool
Helicoil Insert Installation Tool
Thread Insert Installation Tool
HP
HP
HP
HP
HP
HP
HE
HE
HE
AL
HP
HP
HP
HP
HP
HP
HP
HP
HP
4-37
4-35
4-47,4-92
4-41
4-41
4-4
4-115
4-115
4-115
4-112
4-51,4-112
4-51,4-112
4-51,4-112
4-51,4-112
4-51,4-112
4-51,4-112
4-51,4-112
4-51,4-112
4-51,4-112
61-00-65
Page 2-2
Rev. 12 Aug/11
165A
TE
NUMBER
PART NUMBER
DESCRIPTION
VENDOR
PAGE
TE69
TE70
TE71
TE72
TE73
TE74
TE75
TE76
TE77
BST-10001
BST-3056
BST-3057
BST-3054
AST-2856
BST-3037
BST-2982
BST-2983
BST-2806
Transfer Tube O-ring Installation Tool
PCU Bushing Installation Tool
PCU Manifold Installation Tool
Pilot O-ring Installation Tool
Aft Control Spring Compressor
Drill Jig
Drill Jig
Air Pressure Gauge Kit - Obsolete
HP
HP
HP
HP
HP
HP
HP
HP
4-59,4-94
4-54,4-92
4-54,4-92
4-53,4-92
4-4
4-48,4-92
4-40
4-40
OBS
TE78
CST-3028
Dual Acting Propeller Assembly Tool Kit
HP
4-92
TE79
CST-3028-1
Dual Acting Line Maintenance Tool Kit
HP
TE80
BST-2912-10
“C” Flange Spindle
HP
TE81
TE82
TE83
796514021
A-2334
AST-2833
Vacuum Pump 54976-029
Tool Kit
Safety Nozzle
VR
HP
HP
TE84
BST-3041
Rigging Pin
HP
TE85
TE86
TE87
TE88
TE89
TE90
TE91
TE92
TE93
TE94
TE95
BST-2912-11
BST-2958
BST-2938
BST-2939
BST-2939N
BST-2940
BST-2941
BST-2946
DST-2934
AST-2857
BT-1313(-)( )
799200105/
PE 105
BST-2960-3
BST-3045
BST-3039
CST-2987
BST-2947
BST-2948
BST-2949
BST-2950
BST-2951
BST-2952
BST-2876
Stop Pin
Pitch Angle Stop Plug
Shot Peen Plug
Shot Peen Plug
Shot Peen Plug
Shot Peen Plug
Shot Peen Plug
Shot Peen Plug
Blade Bearing Press
Probe and Probe Holder
Eddy Current Probe Unit
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
OL
PE
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
4-94
4-26,
4-91,4-99
4-1
4-1
4-3
4-49,4-92,
4-94
4-26,4-99
4-35
4-29
4-76
4-30
4-30
4-31
4-32
4-100
4-5,4-111
4-66,4-111
TE96
TE97
TE98
TE99
TE100
TE101
TE102
TE103
TE104
TE105
TE106
TE107
Bench Top Blade Angle Protractor
Digital Protractor
Puller
Bearing Puller
Beta System Puller
Bushing Puller
Bearing Puller
Bearing Puller
Bearing Puller
Bearing Puller
Bearing Puller
Pilot Tube Puller
4-112
4-36
4-50,4-92
4-49,4-92
4-89
4-32
4-33
4-33
4-34
4-76
4-34
4-21,4-102
61-00-65
Page 2-3
Rev. 12 Aug/11
165A
TE
NUMBER
TE108
TE108-1
TE108-2
TE109
PART NUMBER
BT-223
BT-223+9
BT-223+10
GFS081
DESCRIPTION
Retention Bearing Puller
Adaptor
Adaptor
Socket, 6 Point, 1/8 inch, 3/8 Drive
VENDOR
PAGE
HP
CS/HP
CS/HP
SO
4-63
4-63
4-63
4-92
TE110
BST-3065
Blade Shot Peen Plug Removal Tool
HP
4-58
TE111
TE112
TE112-1
TE112-3
TE112-4
TE113
TE114
TE115
TE116
TE117
TE118
TE119
TE120
1227-6
BST-3019
BST-3019-3
BST-3019-4
BST-3019-8
BST-2884
BST-2959
BST-2984
DT-1724-( )
BST-10002
BST-3060
AST-2961
BST-2922
Helicoil Insert Removal Tool
Thread Insert Removal Tool
Plug-Lifting Ring
Alignment Check Rod
Alignment Check Rod
Rolling Machine
Beta Valve Freeze Sleeve
Shot Peen Masking Tool
Shipping Sleeve
Modified Deep Well Socket
HE
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
TE121
AST-2979
Test Specimen for Calibration
HP
TE122
TE123
TE124
TE125
TE125-1
TE126
TE127
TE128
TE129
TE130
TE131
TE132
TE133
TE134
TE135
TE136
BST-2912-2
BST-2912-3
BST-2912-1
BST-2912
BST-2912+
BST-3024
BST-2912-12
BST-2847
CST-2901-( )
n/a
BST-2825
79651417A
ED-520
ED-530
79656547A
BST-10003
#20 Spline Spindle
#30 Spline Spindle
Flanged Hub Spindle
Building Buck Components
Blade Assembly Support Stand
Mid Pitch Stop
Probe Support
Propeller Assembly Table
Vu Thru II Tachometer - no longer available
Template
Vacuum Filter 55007-020
Eddy Current Test Instrument
Timer, 12 Hour 6X547
Flight Idle Set Fixture
HP
HP
HP
HP
HP
HP
HP
HP
HP
n/a
HP
VR
MF
MF
PE
HP
TE137
BT-1271-1,2
Shot Peen Tube Assembly
HP
TE138
TE139
TE139-1
AST-2802
AST-2805
AST-2805-1
Plastic Wedge
HP
HP
HP
4-115
4-43
4-43
4-43
4-43
4-22
4-36
4-41
4-102
4-59,4-92
4-55
4-8
4-28
4-13,
4-111
4-26,4-99
4-26,4-99
4-26,4-99
4-26,4-99
4-26,4-99
4-43
4-26,4-99
4-20,4-111
4-99,4-26
OBS
4-18
4-1
4-111
4-111
4-1
4-60,4-92
4-64,4-95,
4-126
4-1
4-2
4-2
61-00-65
Page 2-4
Rev. 12 Aug/11
165A
TE
NUMBER
PART NUMBER
DESCRIPTION
VENDOR
PAGE
HP
HP
HP
HP
HP
SO
SO
n/a
HP
VR
HP
HP
HP
4-2
OBS
4-50,4-92
4-17
4-46
4-25
4-25
n/a
4-15
4-1
4-62
4-3
4-21
TE139-2
TE140
TE141
TE142
TE143
TE144
TE144-1
TE145
TE146
TE147
TE148
TE149
TE150
AST-2805-2
BST-2963
BST-3044
BST-2813
BST-3032
SC058
SC058
n/a
BST-2910
79651407K
BT-461
AST-2814
BST-2860
Spinner Support Plate Wrench
Clamp Wrench
Clamp Nut Wrench
Open End Wrench
Piston Nut Wrench
Piston Nut Wrench
Superseded by TE144-1
Shaft Nut Wrench
Vacuum Oil 54996-252
Spanner Wrench
Torque Wrench
TE151
AST-2915
TE152
AST-2917
HP
4-6
TE153
TE154
TE155
TE156
TE157
TE158
TE159
TE160
TE161
TE162
TE163
TE164
TE165
BST-2921
AST-2953
AST-2877-1
796540702
BST-10005
79651009A
BST-10007
7965639221
BST-2974
BST-2974-1
BST-2974-2
BST-2974-3
BST-2974-4
Vacuum Hose YA-6407-02
Beta Switch Tester
Vacuum Gauge 1009A
Threaded Headless Pins
Vacuum Fitting YA-6392-21
Erosion Shield Bonding Clamp
HP
HP
HP
CP
HP
JC
HP
CP
HP
HP
HP
HP
HP
4-27
4-7
4-6,4-94
4-1
4-61,4-92
4-1
4-62,4-92
4-1
4-38
4-38
4-38
4-38
4-38
TE166
GTMU121
Universal Socket, 12 Point, 3/8 inch, 1/4 Drive
SO
4-92
TE167
TE168
TE169
TE170
TE171
TE172
TE173
TE174
TE175
TE176
TE177
TE178
n/a
BST-2974-7
n/a
n/a
BST-2975
BST-2975-1
BST-2975-2
BST-2975-3
BST-2975-4
APS351
BST-2975-6
BST-2975-7
n/a
n/a
n/a
Fit Check Tool
Fit Check Tool
Fit Check Tool
Fit Check Tool
Fit Check Tool
Adjustable Spanner Wrench, 1/8 Pin
Fit Check Tool
Fit Check Tool
n/a
HP
n/a
n/a
HP
HP
HP
HP
HP
SO
HP
HP
n/a
4-38
n/a
n/a
4-39
4-39
4-39
4-39
4-39
4-92
4-39
4-39
OBS
61-00-65
Page 2-5
Rev. 14 Jun/13
165A
TE
NUMBER
PART NUMBER
DESCRIPTION
VENDOR
PAGE
TE179
TE180
TE181
TE182
n/a
BST-2975-9
BST-2966
BST-2966-3
n/a
Fit Check Tool
Spinner Support Plate Ream Fixture
n/a
HP
HP
HP
n/a
4-39
4-38
4-38
TE183
BST-2966-4
HP
4-38
TE184
BST-2966-5
HP
4-38
TE185
TE186
TE187
BST-3055
BST-3055-1
CST-3000
PCU Bearing Installation Tool
Initial Erosion Shield Sample Program Kit
HP
HP
HP
4-53,4-92
4-53,4-92
4-90
TE188
CST-3000-1
HP
4-90
TE189
CST-3000-2
HP
4-90
TE190
CST-3000-3
HP
4-90
TE191
CST-3000-4
HP
4-90
TE192
GFC48A
Crowfoot Wrench, Open End with Side Lock Hole,
1 1/2 inch, 3/8 Drive
SO
4-92
TE193
CST-3000-6
HP
4-90
TE194
CST-3000-7
HP
4-90
TE195
n/a
n/a
n/a
n/a
TE196
CST-3000-9
HP
4-90
TE197
n/a
n/a
n/a
n/a
TE198
n/a
n/a
n/a
n/a
TE199
n/a
n/a
n/a
n/a
TE200
n/a
n/a
n/a
n/a
TE201
n/a
n/a
n/a
n/a
TE202
GFS161
Deep Well Socket, 12 Point, 1/2 inch, 3/8 Drive
SO
4-92
TE203
n/a
n/a
n/a
n/a
TE204
n/a
n/a
n/a
n/a
TE205
n/a
n/a
n/a
n/a
TE206
n/a
n/a
n/a
n/a
TE207
BT-1465-1
Floating Reamer
HP
4-67
TE207-1
BT-1465-3
Floating Reamer
HP
4-67
TE208
BT-1465-2
Floating Reamer
HP
4-67
TE208-1
BT-1465-4
Floating Reamer
HP
4-67
TE209
n/a
n/a
n/a
n/a
TE210
n/a
n/a
n/a
n/a
TE211
n/a
n/a
n/a
n/a
TE212
n/a
n/a
n/a
n/a
TE213
n/a
n/a
n/a
n/a
TE214
GFC012
Crowfoot Wrench, Open End, 3/8 in
SO
4-94,4-92
TE215
n/a
n/a
n/a
n/a
61-00-65
Page 2-6
Rev. 12 Aug/11
165A
TE
NUMBER
TE216
PART NUMBER
n/a
DESCRIPTION
n/a
VENDOR
PAGE
n/a
n/a
TE217
n/a
n/a
n/a
n/a
TE218
n/a
n/a
n/a
n/a
TE219
BST-3004
Template
HP
4-42
TE220
BST-3004-1A
Template
HP
4-42
TE221
BST-3004-1B
Template
HP
4-42
TE222
BST-3004-2A
Template
HP
4-42
TE223
TE224
TE225
TE226
TE227
TE228
TE228-1
TE229
TE230
TE231
TE232
TE233
TE234
TE235
TE236
TE237
TE238
TE239
TE240
TE241
BST-3004-2B
BST-3004-3A
BST-3004-3B
BST-3004-4A
BST-3004-4B
BST-3067
BST-3067+3
GFA4A
BST-3004-6A
BST-3004-6B
BST-3004-7A
BST-3004-7B
n/a
n/a
BST-3004-9A
BST-3004-9B
BST-3026-1
BST-3026-2
BST-3026-3
BST-3064
Template
Template
Template
Template
Template
Piston Installation Socket
Socket Driver, 5/32 Hex. Head, 3/8 Drive
Template
Template
Template
Template
n/a
n/a
Template
Template
Bearing Press
Bearing Press
Bearing Press
Pilot Tube Installation Tool Kit
HP
HP
HP
HP
HP
HP
HP
SO
HP
HP
HP
HP
n/a
n/a
HP
HP
HP
HP
HP
HP
4-42
4-42
4-42
4-42
4-42
4-29
4-29
4-92
4-42
4-42
4-42
4-42
n/a
n/a
4-42
4-42
4-44
4-44
4-44
4-57
TE241-1
BST-3064A
Pilot Tube Installation Tool Kit - Kit without the Pilot
Tube Installation Tool
HP
4-57
TE242
TE243
TE244
TE245
TE246
TE247
TE248
TE249
TE250
TE251
TE252
TE253
BST-3064-1
BST-3064-2
BST-3064-3
BST-3064-4
BST-3064-5
BST-3068
GF10M
GVO1820
PFDH180
BST-10004
668
QJFR275E
Pilot Tube Installation Tool
Pilot Tube Positioner and Stop
Peening Tool
Breaker Bar, 3/8 Drive
Open End Wrench, Std Length, 9/16 - 5/8 in
Socket, 12 Point, 9/16 inch, 3/8 Drive
Thickness Gauge
Adjustable Torque Wrench, 5 to 75 ft-lb, 3/8 Drive
HP
HP
HP
HP
HP
HP
SO
SO
SO
HP
ST
SO
4-57,4-84
4-57,4-84
4-57,4-84
4-57,4-84
4-57,4-84
4-68
4-92
4-93
4-93
4-60,4-92
4-93
4-93
61-00-65
Page 2-7
Rev. 12 Aug/11
165A
TE
NUMBER
TE254
TE255
TE256
TE257
TE258
TE259
TE260
TE261
TE262
TE263
TE264
TE265
TE266
TE267
TE268
TE269
TE270
TE271
TE272
TE273
TE274
TE275
TE276
TE277
TE278
TE279
TE280
TE281
TE282
TE283
TE284
TE285
TE286
TE287
TE288
TE289
TE290
TE291
TE292
TE293
TE294
TE295
PART NUMBER
QJR217C
GFX1
GFC60A
ASA204A
170-6
1500-P
90303A247
BLX13
EN1901
CUTA2810114C
CUTA1870104C
M22520/1-01
CUTA1560203A
CUTA1560103B
CUTA2180203B
CUTA2180103B
CUTA2810203B
CUTA2810103B
CUTA3120203B
CUTA3120103B
BST-2970
MR02030
CST-3028-2
CST-3012
BST-2810
BST-2808
AST-2807
AST-2809
AST-2827
BST-2828
AST-2827-1
791256000
n/a
BST-2850
AST-2852
BST-3152
BST-3151
AST-2851
D1208A
D2203
90303A542
BST-2832
DESCRIPTION
VENDOR
PAGE
Adjustable Torque Wrench, 30 to 200 in-lb, 3/8 Drive
Extension, 2 inches, 3/8 Drive
Crowfoot Wrench, 1 7/8 inch, 3/8 Drive
Miniature Pick Set
Apex Torqset Bit, 1/4 inch, 1 1/4 Length
Hand Driver, Replaceable-Bit
Nylon Jack Screws
Ball Head Hex. Wrench Set
Propeller Sling, 1 inch x 3 feet
Installation & Extraction Tool for Relief Valve
Installation & Extraction Tool for Oil Nozzle
Beta Light Switch Crimping Tool
Lee Plug Installation Tool
Lee Plug Extraction Tool
PCU Bearing Seat Sander
Roller, Steel 1½" x 2"
Ultrasonic Inspection Calibration Standard
Coupling Unit
Relief Valve Unit
Air Gauge
Hose Unit
Spring Compressor Bolt
Spring Compressor Slide
Spring Compressor Bolt
Ultrasonic Flaw Detector Kit
n/a
Threaded Rod
Drilled Washer
Thrust Bearing
5/8 Hex Nut
Guide Washer
Electric Actuator
Control
Nylon Jack Screws
Superseded by BT-1313
SO
SO
SO
SO
AP
AP
MC
BH
LC
LE
LE
DM
LE
LE
LE
LE
LE
LE
LE
LE
HP
EP
HP
HP
HP
HP
HP
HP
HP
HP
HP
PM
n/a
HP
HP
HP
HP
HP
VC
VC
n/a
n/a
4-93
4-93
4-93
4-93
4-93
4-93
4-93
4-92
4-94,4-92
4-93
4-93
4-93
4-93
4-93
4-93
4-93
4-93
4-93
4-93
4-93
4-69
4-117
4-94
4-97,4-116
OBS
OBS
OBS
OBS
4-18
4-19,4-18
4-19
4-116
n/a
4-20
4-20
4-20
4-20
4-20
OBS
OBS
OBS
OBS
61-00-65
Page 2-8
Rev. 15 Dec/13
165A
TE
NUMBER
PART NUMBER
DESCRIPTION
VENDOR
PAGE
4-70
4-70
4-28
4-71
4-71
4-71
4-117,
4-118
4-118
4-117,
4-118
4-93
4-118
4-118
4-56,4-63
4-56,4-63
4-71
4-68
OBS
OBS
OBS
4-69,4-11
4-119
n/a
4-101,
4-52
4-8,4-20
4-51,4-94
4-16
n/a
4-93
4-93
OBS
OBS
4-26,4-99
4-117
4-117
4-117
4-117
4-119
4-10
4-10
TE296
TE297
TE298
TE299
TE300
TE301
BST-3070
BST-3071
BST-2932
BST-10037
BST-10038
BST-10039
Drill Jig, PCU
PCU Stand
Dummy Pitch Change Rod
E13890 Master Blade, Group 1
HP
HP
HP
CS
CS
CS
TE302
HZP161001
E10950 Blade Repair Blanket
BR
TE303
HL1802E
Heat Gun
SA
TE304
HZP161002
Blade Repair Blanket (4" x 12")
BR
TE305
TE306
TE307
TE308
TE309
TE310
TE311
TE312
TE313
TE314
TE315
TE316
TE317
PMF133
240-120F
240-190F
BST-3061
BST-3062
BT-3035
BST-3066-2
n/a
n/a
n/a
BST-3069
9943HART-001
n/a
0 - 6 inch Dial Calipers
Temp-Plate® Recorder 120°F to 180°F
Temp-Plate® Recorder 190°F to 220°F
Press Tool
Press Tool
Centering Tool for C-5623-2 Drive Coupling
Stop Adaptor
Eddy Current Fixture
Unfeathering Tool
n/a
SO
WI
WI
HP
HP
HP
HP
n/a
n/a
n/a
HP
CG
n/a
TE318
DST-3049-( )
Ground Hydraulic Power Unit (GHPU)
HP
TE319
TE320
TE321
TE322
TE323
TE324
TE325
TE326
TE327
TE328
TE329
TE330
TE331
TE332
TE333
TE334
AST-2981
BST-3048
BST-2811
n/a
CUTA1250203A
CUTA1250103B
n/a
n/a
BST-2912-13
MR01020
MR10900
MR05000
MR05020
GS4H
AT-3010
AT-3011
Assembly Guide
Transfer Tube and Plug Removal/Installation Tool
Flatness Gauge
n/a
Superseded by TE122
Superseded by TE123
Blade Angle Stop
Roller, Smooth 1 1/8" x 1/8"
Roller, Gooseneck 1" x 1/16"
Roller, Rubber 2"
Roller, Silicon 1 5/16" x 1¾"
Tie Strap Gun
Balance Tube Positioner
HP
HP
HP
n/a
LE
LE
n/a
n/a
HP
EP
EP
EP
EP
AE
HP
HP
61-00-65
Page 2-9
Rev. 12 Aug/11
165A
TE
NUMBER
PART NUMBER
DESCRIPTION
VENDOR
PAGE
TE335
TE336
TE337
TE338
TE339
TE340
TE341
TE342
TE343
BST-3004-10A
BST-3004-10B
BST-3004-11A
BST-3004-11B
n/a
BST-2975-10
CST-3000-10
CST-3000-A
n/a
Template
Template
Template
Template
n/a
Fit Check Tool
Supplemental Erosion Shield Sample Program Kit
HP
HP
HP
HP
n/a
HP
HP
HP
n/a
4-42
4-42
4-42
4-42
n/a
4-39
4-90
4-90
OBS
TE344
n/a
n/a
OBS
TE345
CST-3000-1A
HP
4-90
TE346
CST-3000-2A
HP
4-90
TE347
CST-3000-3A
HP
4-90
TE348
CST-3000-4A
HP
4-90
TE349
CST-3000-6A
HP
4-90
TE350
CST-3000-7A
HP
4-90
TE351
CST-3000-9A
HP
4-90
TE352
CST-3000-10A
HP
4-90
TE353
TE354
TE355
TE356
TE357
TE358
TE359
TE360
TE361
TE362
TE363
TE364
TE365
TE366
TE367
TE368
TE369
TE370
TE371
TE372
BST-2930-5
SR19W4-A
CUST. P/N
CUST. P/N
CG40-4
CG40-7
240-090F
90F2312
BST-10015
DST-10024
DST-10024-1
BST-10026
DST-10016
DST-10025
CG250-8A and
CG250-9
CG41-11
CG41-14
CG41-13
MS27495R20
000-951-005
BST-3080
BST-3080-1
Megohm Meter
Milliohmmeter
PCU Filter Removal Tool, Rod
PCU Filter Removal Tool, Collet
Temp-Plate® Recorder 90°F - 120°F
Signal Generator Model 3001
Modified Crowfoot
HP
RC
AR
AR
SO
SO
WI
BK
SO
4-121
4-122
4-110
4-110
4-120
4-120
4-72
Bolt Alignment Tool
HP
4-103
Pitch Lock Roller Fixture
Roller Assembly Tool
Go-No-Go Gauge
HP
HP
HP
4-72
4-103
4-104
Slide Hammer, 2 lb.
SO
4-123
Slide Hammer, Rod
Slide Hammer, Collet, 1/4 inch to 5/16 inch
Slide Hammer, Collet, 3/8 inch to 7/16 inch
Pin Extractor
Bransonic Cleaner Model B3
Shot Peen Plug
Shot Peen Plug
SO
SO
SO
CS
BN
HP
HP
4-123
4-123
4-123
4-122
4-121
4-73
4-73
Slimsert® Installation Tool
4-13
61-00-65
Page 2-10
Rev. 16 Apr/14
165A
TE
NUMBER
PART NUMBER
DESCRIPTION
TE373
CST-10050
TE374
CUST. P/N
Transducer Assembly
TE375
Approved Units
Ultrasonic Flaw Detector
TE376
TE377
TE378
n/a
BST-2975-12
BST-2975-13
n/a
Fit Check Tool
Fit Check Tool
TE379
02643
Shot Peen Gun
TE380
TE381
TE382
TE382-1
TE383
TE384
TE385
TE386
TE387
TE388
CST-3110
BST-3109
DST-3146
DST-3146-1
BST-3103
BST-3104
BST-2837+1+3
BST-2837+2
B-3368
A-3204
Cylinder Cap
T-Handle Wrench
Thread Gauge Airflow Kit
Feathering Tool
Cylinder Installation Rod
Modified Socket
Anti-Rotation Pin
5/16-24 Hex Nut
5/16-24 Set Screw
TE389-1
BST-2930-1
SR25W4A
MR25W4A
225-072722
TE389-2
BST-2930-2
SR43W4A
MR43W4A
225-072734
TE389-3
BST-2930-3
SR50W4A
MR50W4A
225-072738
225-890051
TE389-4
BST-2930-4
SR56W4A
MR56W4A
225-072742
225-890053
TE389-5
BST-2930-5
SR19W4A
MR19W4A
225-072718
TE389-6
BST-2930-6
SR16W4A
MR16W4A
225-072714
VENDOR
PAGE
HP
4-88
4-124,
PM
4-116
4-124,
Cust. P/N
4-116
n/a
n/a
HP
4-39
HP
4-39
4-126,
CL
4-64,4-95
HP
4-96
HP
4-74
HP
4-106,4-81
HP
4-81,4-106
HP
4-74
HP
4-75
HP
4-19
HP
4-19
HP
4-20
HP
4-20
HP
RC
MK
AC
4-114,4-12
HP
RC
MK
AC
4-114
HP
RC
MK
AC
AC
4-114
HP
RC
MK
AC
AC
4-114
HP
RC
MK
AC
4-114
HP
RC
MK
AC
4-114
61-00-65
Page 2-11
Rev. 17 Dec/14
165A
TE
NUMBER
PART NUMBER
VENDOR
PAGE
HP
RC
MK
AC
AC
4-114
HP
RC
MK
AC
4-114
HP
RC
MK
AC
4-114
BST-2930-10
SR11W4A
TE389-10
MR11W4A
225-072706
HP
RC
MK
AC
4-114
TE390
DT-2997-2
Pressure Check Adapter
CS
TE391
DT-2997-4
Pitch Change Bore Plug
CS
TE392
DT-2997-5
CS
TE393
DT-2997-7
CS
TE394
DT-2997-8
CS
TE395
TE396
TE397
TE398
TE399
TE400
TE401
TE402
TE403
TE403-1
0.0525 inch dia.
0.0620 inch dia.
0.0850 inch dia.
0.2634 inch dia.
0.2700 inch dia.
0.0962 inch dia.
0.1400 inch dia.
0.1480 inch dia.
BST-3022
BST-3022A
Gear Inspection Wire
Reamer
Reamer
VK
VK
VK
VK
VK
VK
VK
VK
HP
HP
4-105,
4-104
4-104,
4-105
4-104,
4-105
4-105,
4-104
4-105,
4-104
4-125
4-125
4-125
4-125
4-125
4-125
4-125
4-125
4-75
4-75
TE404
AST-2968
Stud Installation/Torque Check Tool
HP
4-12
TE404-1
AST-2968-1
HP
4-12
TE404-2
AST-2968-2
HP
4-12
TE405
TE406
TE407
TE408
TE409
AST-3163-( )
AST-3157
AST-2971-1
AST-2971-2
A-2327
Shot Peen Plug Kit
Shot Peen Plug
Screw - 0.50 inch (12.7 mm)
Screw - 0.62 inch (15.7 mm)
Slimsert® Repair Kit
HP
HP
HP
HP
HP
4-11
4-11
4-11
4-11
4-12
TE389-7
BST-2930-7
SR37W4A
MR37W4A
225-072730
225-890031
TE389-8
BST-2930-8
SR31W4A
MR31W4A
225-072726
TE389-9
BST-2930-9
SR14W4A
MR14W4A
225-072710
DESCRIPTION
61-00-65
Page 2-12
Rev. 15 Dec/13
165A
TE
NUMBER
PART NUMBER
DESCRIPTION
VENDOR
PAGE
HP
RC
4-12
TE410
B-6986-258
SR258
TE411
791762313
Tap
5/16-24 UNF-3B MOD
HP
RC
4-12
TE412
BST-2931-1
SR25D
Step Drill
HP
RC
4-12
TE413
TE414
TE415
TE416
TE417
TE418
TE419
TE420
TE421
CST-2969
BST-3006
BST-3158
BST-3159
BST-3160
BST-3161
BST-3162
BST-2991
AST-3154
Blade Angle Locating Fixture
Paint Mask Cap
Paint Mask Cap
Paint Mask Cap
Paint Mask Cap
Paint Mask Cap
Paint Mask Cap
Spacer
HP
HP
HP
HP
HP
HP
HP
HP
HP
4-96
4-77
4-77
4-77
4-77
4-77
4-77
4-78
4-13
TE422
B-6986-192
SR192
Slimsert®
HP
RC
4-13
TE423
99620070
1/4-28 UNF-3B
Tap
HP
RC
4-13
TE424
BST-2931-5
SR19D
Step Drill
HP
RC
4-13
TE425
TE426
TE427
TE428
n/a
n/a
CST-3169
BST-3081
n/a
n/a
Sleeve Installation Tool
Mask Screw
n/a
n/a
HP
HP
TE429
DT-2997-9
CS
No Go Gauge
HM
4-127
A Flange Spindle
Eddy Current Probe
Calibration Standard
Profilometer
Probe Housing Component
Blade Pitch Fixture
Ball Hex Driver
Blade Seal Alignment Tool
Pressure Check Tool
Pressure Check Tool - Kit without the Pilot Tube
Installation Tool
CS
CS
HP
HP
HP
MH
HP
CS
HP
HP
HP
CS
4-71
4-7
4-26
4-127
4-98
4-14,4-79
4-79,4-14
4-79
4-14
4-80
4-80
4-82
CS
4-82
TE431
TE432
TE433
TE434
TE435
TE436
TE437
TE438
TE439
TE440
TE440-1
TE441
.2760 Pin Gauge,
Minus "Y" Tolerance
BST-3200
AST-3175
BST-2912-17
101088
CST-3015
AST-3475
BST-3227
BST-3226
AST-3174
BST-3177
BST-3063
BST-7587
TE441-1
BST-7587-1
TE430
Slimsert®
n/a
n/a
4-97
4-78
4-105,
4-104
61-00-65
Page 2-13
Rev. 17 Dec/14
165A
TE
NUMBER
PART NUMBER
DESCRIPTION
VENDOR
PAGE
TE441-2
TE442
BST-7587-2
BST-4114
Pressure Check Tool
Composite Balance Tube Puller
CS
CS
4-82
4-80
TE443
BT-3838
Grease Seal Pressure Test Tool (Adapter)
HP
4-81,4-106
TE443-1
TE444
TE445
BT-3838-1
DST-3483
BST-7588
Grease Seal Pressure Test Tool
Masking Fixture
Insert Installation Tool
HP
CS
CS
TE446
DST-5855(F)
Shot Peen Machine Assembly
TE447
DST-5855-1(F)
Shot Peen, "Y" Shank Knob Kit
HP
TE448
CST-3178
Bolt Alignment Fixture
HP
TE449
101679
"E" Shank Form Tool
HP
TE449-1
105473
"E" Shank Form Tool
HP
TE450
101736
"E" Shank Potting Mold
HP
TE451
GT-3669
Composite E-shank Comparison Chart
HP
TE452
TE453
TE454
TE455
TE456
TE457
TE458
TE459
TE460
TE461
TE462
TE463
TE464
TE465
TE466
TE467
TE468
TE469
TE470
TE471
TE472
TE473
101999
101923
101781
101932
103570
101939
101060
103572
102690
BST-3004-12A
BST-3004-12B
BST-3004-13A
BST-3004-13B
BST-3004-14A
BST-3004-14B
BST-3004-15A
BST-3004-15B
BST-3004-16A
BST-3004-16B
BST-3004-19A
BST-3004-20A
BST-3004-20B
Tube Puller Assembly
Balance Adapter
Plug Puller
Blade Spud Adapter
Mandrel
Torque Wrench Adapter
Shot Peen Plug
Ring
Template
Template
Template
Template
Template
Template
Template
Template
Template
Template
Template
Template
Template
TE474
CST-3000-11
TE475
CST-3000-11A
4-81,4-106
4-107
4-82
4-108,
CS/WH
4-109
CS
CS
HP
CS
CS
CS/HP
HP
CS
CS
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
4-109,
4-108
4-98
4-128,
4-129
4-128,
4-129
4-128,
4-129
4-129,
4-128
4-129
4-130
4-130
4-131
4-131
4-132
4-132
4-133
4-71
4-42
4-42
4-42
4-42
4-42
4-42
4-42
4-42
4-42
4-42
4-42
4-42
4-42
HP
4-90
HP
4-90
61-00-65
Page 2-14
Rev. 15 Dec/13
165A
TE
NUMBER
PART NUMBER
DESCRIPTION
VENDOR
PAGE
TE476
CST-3000-12
HP
4-90
TE477
CST-3000-12A
HP
4-90
TE478
CST-3000-15
HP
4-90
TE479
CST-3000-15A
HP
4-90
TE480
TE481
TE482
TE483
TE484
TE485
TE486
TE487
TE488
TE488-1
TE488-2
TE489
TE489-1
TE489-2
TE489-3
TE490
TE490-1
TE490-2
TE490-3
TE490-4
TE491
BST-2975-14
BST-2975-16
BST-2975-17
BST-2975-18
BST-2975-19
BST-2975-20
791911212
CST-421
BST-2890
BST-2891
BST-2894
BST-2895
BST-2896
BST-2897
BST-2899
BST-2902
BST-2903
BST-2904
BST-2905
BST-2907
DST-3017
Fit Check Tool
Fit Check Tool
Fit Check Tool
Fit Check Tool
Fit Check Tool
Fit Check Tool
212-8 Driver
Stud Fixture Plate
Spring Compressor Base
Spring Compressor Retainer
Spring Compressor Guide Rod
Propeller Transport Cart
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
TE492
BST-3050
Chip Detector Fitting
HP
TE493
BST-3051
Chip Dectector Fitting Cover
HP
TE494
BT-1271-4
Shot Nozzle Unit
HP
TE494-1
BT-1271-5
Shot Nozzle Unit
HP
TE494-2
BT-1271-6
Shot Nozzle Unit
HP
TE494-3
BT-1271-7
Shot Nozzle Unit
HP
TE494-4
BT-1271-8
Shot Nozzle Unit
HP
TE495
TE496
TE497
TE498
104287
104371
104372
104374
Torque Wrench
Stand Adapter
Drive Housing Adapter
Roughness Standard
CS
MF
MF
MF
4-39
4-39
4-39
4-39
4-39
4-39
4-133
4-83
4-22,4-85
4-22,4-85
4-22,4-85
4-23,4-85
4-23,4-86
4-23,4-85
4-23,4-85
4-24,4-85
4-24,4-86
4-24,4-85
4-24,4-85
4-24,4-85
OBS
4-52,
4-101
4-52,
4-101
4-64,4-95,
4-126
4-64,4-95,
4-126
4-64,4-95,
4-126
4-64,4-95,
4-126
4-64,4-95,
4-126
4-134
4-134
4-135
4-135
61-00-65
Page 2-15
Rev. 15 Dec/13
165A
TE
NUMBER
TE499
TE500
TE501
TE502
TE503
TE504
TE505
TE506
TE507
TE508
TE509
TE510
TE511
TE512
TE513
TE514
TE515
TE516
TE517
TE518
TE519
TE520
TE521
TE522
TE523
TE524
TE525
TE526
TE527
TE528
TE529
TE530
TE531
TE532
TE533
TE534
TE535
TE536
TE537
TE538
TE539
TE540
TE541
TE542
TE543
PART NUMBER
M22520/37-01
BST-3076
BST-3077-1
104933
104811
105189
105190
104507
104504
104798
105167
104506
BST-2975-21
BST-2975-22
BST-2975-23
BST-2975-24
BST-2975-25
BST-3075
105266
105269
BST-2912-20
BST-2912-21
BST-3004-21A
BST-3004-21B
BST-3004-22A
BST-3004-22B
BST-3004-23A
BST-3004-23B
BST-3004-24A
BST-3004-24B
BST-3004-25A
BST-3004-25B
105274
Contact Hartzell
102560
105478
104052
BST-2912-19
102515
102516
105501
103454
BST-2974-5
BST-2974-6
BST-2974-8
DESCRIPTION
Crimp Tool
Eddy Current Probe
Fitting Wrench
Spacer Blank
Bearing Assembly Tool
Clamp
Leak Check Manifold
Adapter
Check Cylinder
Check Cylinder
Plug Assembly
Fit Check Tool
Fit Check Tool
Fit Check Tool
Fit Check Tool
Fit Check Tool
Double Shoulder Blade Eddy Current Kit
Torque Unit Adapter
Torque Unit Adapter
Hovercraft 5-Way Adapter
Template
Template
Template
Template
Template
Template
Template
Template
Template
Template
Balance Adapter
Bantam Blade Spud Adapter
Leak Detector Kit
Blade Adapter Service Tool
Drill Jig for N7605 Shank
“H”, “T”, “Q”, and “G” Flange Spindle
Shank Spacer Puller
Shank Spacer Puller
Blade Inspection Adapter
Stud Preload Plate
VENDOR
PAGE
CS
HP
CS
CS
CS
CS
CS
CS
CS
HP
CS
CS
HP
HP
HP
HP
HP
HP
CS
CS
CS
CS
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
CS
CS
CS
CS
HP
HP
HP
4-136
4-136
4-137
4-137
4-138
4-139
4-139
4-140
4-140
4-141
4-141
4-142
4-39
4-39
4-39
4-39
4-39
4-143
4-144
4-144
4-145
4-145
4-42
4-42
4-42
4-42
4-42
4-42
4-42
4-42
4-42
4-42
4-146
4-146
4-147
4-147
4-148
4-26
4-149
4-149
4-150
4-150
4-38
4-38
4-38
61-00-65
Page 2-16
Rev. 15 Dec/13
165A
TE
NUMBER
TE544
TE545
TE546
TE547
TE548
TE549
TE550
TE551
TE552
TE553
TE554
TE555
TE556
TE557
TE558
TE559
PART NUMBER
BST-2974-9
BST-2974-10
BST-2974-11
105615
105532
BST-2975-15
BST-2912-22
AST-2877-2
BST-2975-26
BST-2975-27
BST-2975-30
BST-2975-31
BST-2975-32
BST-2975-33
BST-2975-34
105702
DESCRIPTION
Valve Assembly Check Tool
Bantam Spring Compressor
Fit Check Tool
"F" Flange Bantam Adapter Ring
Fit Check Tool
Fit Check Tool
Fit Check Tool
Fit Check Tool
Fit Check Tool
Fit Check Tool
Fit Check Tool
Right Angle Grease Coupler
VENDOR
PAGE
HP
HP
HP
CS
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
4-38
4-38
4-38
4-149
4-150
4-39
4-26,4-153
4-6
4-39
4-39
4-39
4-39
4-39
4-39
4-39
4-153
61-00-65
Page 2-17
Rev. 17 Dec/14
165A
61-00-65
Page 2-18
Rev. 17 Dec/14
165A
The Alphabetical Index has been replaced by the Tool and Equipment Index.
Refer to the Tool and Equipment Index in this manual.
ALPHABETICAL INDEX
61-00-65
Page 3-1
Rev. 12 Aug/11
165A
ALPHABETICAL INDEX
61-00-65
Page 3-2
Rev. 12 Aug/11
165A
Tool Kit
Part Number: A-2334 (TE82)
Description:
Kit to prepare facilities for erosion shield replacement on composite blades.
The kit contains the following:
Vendor
Vendor P/N
Hartzell P/N
Description
Qty/Size
VR
54976-029 796514021 (TE81)
Vacuum Pump
1
VR
55007-020 79651417A (TE132)
Filter
1
PE
6X547
79656547A (TE135)
Timer, 12-hour
2
VR
54996-252
79651407K (TE147)
Vacuum Oil 5 gallons
CP
YA-6407-02 796540702 (TE156)
Vacuum Hose
(6 ea.) 10 feet
JC
1009A 79651009A (TE158)
Vacuum Gauge
2
CP
YA-6392-21 7965639221 (TE160)
Vacuum Fitting
1
Plastic Wedge
Part Number: AST-2802 (TE138)
Description:
Wedge to aid in separating the hub halves of an aluminum hub propeller
without scarring the mating surfaces.
TOOL AND EQUIPMENT LIST
61-00-65
Page 4-1
Rev. 12 Aug/11
165A
Ring Centering Tool
Description:
Tool to keep internal rings in alignment. Used during assembly of oil
transfer unit for A-224-2 Seal in propeller model HC-A2X20-4( )2.
AST-2805-1 (TE139-1)
AST-2805-2 (TE139-2)
Description:
“K” flange steel hub propellers
“W” flange propellers
“D” flange propellers
Wrench to tighten and torque mounting bolts on propellers. Used
in conjunction with a standard 1/2 inch square drive torque wrench.
61-00-65
Page 4-2
Rev. 12 Aug/11
165A
Description:
Wrench to tighten and torque 9/16 inch, 12 point mounting bolt. Used in
conjunction with a standard 1/2 inch square drive torque wrench.
Supersedes: A-2814
Safety Nozzle
Description:
Fitting to ensure safe use of air nozzle.
61-00-65
Page 4-3
Rev. 12 Aug/11
165A
Beta Rod Retainer Installation Tool
Description:
Tool to crimp the beta rod retainers onto the beta rod. Used in conjunction
with a standard vise.
APS-201
Pilot O-ring Installation Tool
Description:
Installation tool for A-217-1, -2 Plug. For use with A-224-3, -4 Oil Transfer Unit.
NOTE:
This part number may be used to order the drawing to
permit local fabrication.
61-00-65
Page 4-4
Rev. 12 Aug/11
165A
Probe and Probe Holder
Description:
Part of Eddy Current Instrument used to inspect “Y” shank aluminum blade
retention radius.
APS-381
Block
Area to be
Inspected
Probe
Hub Bearing Radius Comparator
Description:
Comparator to ensure proper fit of blade retention bearing into “D” or “Y”
shank hubs.
APS-155
61-00-65
Page 4-5
Rev. 12 Aug/11
165A
5/8 inch
Used for lightweight turbine propellers
that use 5/8 -18, 12 point propeller
mounting bolt.
AST-2877-1 (TE155) 11/16 inch Used for dual acting and light weight
turbine propellers that use
mounting nut C-6006.
AST-2877-2 (TE551) 11/16 inch Used for Beechcraft HC-E5P-3( )
installation only.
Description:
Wrench adaptor to install and torque mounting bolts. Used in conjunction
with a standard 1/2 inch square drive torque wrench.
APS-543
Propeller
Mounting Flange
Aircraft Engine
Mounting Flange
Propeller
Mounting
O-ring
Mounting
Bolt
Standard Torque
Wrench
Torque Wrench Adaptor AST-2877-( )
Part Number
AST-2917 (TE152)
Description
Wrench to tighten and torque propeller mounting bolts on “K” flange
propellers. Used in conjunction with a standard 1/2 inch square drive
torque wrench.
Supersedes: A-1327
61-00-65
Page 4-6
Rev. 17 Dec/14
165A
Description:
Wrench to tighten and torque mounting bolts on “L” flange propellers. Used in
conjunction with a standard 1/2 inch square drive torque wrench.
Description:
Wrench to tighten and torque mounting bolts on “W” flange propellers. Used
in conjunction with a standard 1/2 inch square drive torque wrench.
NOTE:
This part number may be used to order the drawing of the
torque wrench adaptor to permit local fabrication.
AST-3175
61-00-65
Page 4-7
Rev. 14 Jun/13
165A
Shipping Sleeve
Description:
Sleeve to prevent damage to air valves on feathering compact propellers
during shipping and handling.
Assembly Guide
Description:
Assembly tool for Spring Assemblies. Used with BST-2853 (TE9) Assembly
Tool.
NOTE:
One order of Assemby Guide AST-2981 includes a quantity of
two (2) guides.
61-00-65
Page 4-8
Rev. 12 Aug/11
165A
Spring Compressor
Part Number: AT-725-1 (TE29)
Description:
Spring compressor for beta springs during assembly.
(This space is intentionally blank.)
61-00-65
Page 4-9
Rev. 12 Aug/11
165A
Part Number: AT-3010 (TE333)
Description:
Balance tube positioner used for installing balance tubes in "M" shank
composite blades.
AT-3010
Part Number: AT-3011 (TE334)
Description:
Balance tube positioner used for installing balance tubes in composite
blades used in an aluminum hub propeller.
AT-3011
61-00-65
Page 4-10
Rev. 15 Dec/13
165A
Shot Peen Plug Kit
Part Number: AST-3163-( ) (TE405)
Description:
Kit to mask the chamfered lubrication fittings in two-blade and three-blade
aluminum hubs.
Kit:
AST-3163
Kit for two-blade aluminum hubs, includes:
Components
Quantity
1. . . . . AST-3157 (TE406)
Shot Peen Plug
2. . . . . AST-2971-1 (TE407) Screw - 0.50 inch (12.7 mm)
AST-3163-1
Kit for three-blade aluminum hubs, includes:
Components
1. . . . . AST-3157 (TE406)
Shot Peen Plug
4
2
2
Quantity
6
6
AST3157
AST2971
Shot Peen Plug
Screw
61-00-65
Page 4-11
Rev. 12 Aug/11
165A
Part Number: AST-2968 (TE404) (Install/check 1/2-20 [12.7 mm] studs.)
AST-2968-1 (TE404-1) (Install/check 9/16-18 [14.2 mm] studs.)
AST-2968-2 (TE404-2) (Install/check 7/16-20 [10.9 mm] studs.)
Description:
Used to install hub mounting studs and to check the required torque after stud
adhesive cures.
AST2968
Part Number: A-2327 (TE409)
Description:
Kit including tools and parts necessary to repair to the lubrication fitting
holes in aluminum hubs. The kit contains the following:
Vendor Vendor P/N
Hartzell P/N
Description
Qty
RC
SR258
B-6986-258 (TE410)
Slimsert®1
n/a
5/16-24 UNF-3B MOD 791762313 (TE411)
(Minor diameter
0.280-0.285 MOD)
Tap
1
RC
SR25W4-A
BST-2930-1 (TE389-1) Slimsert® Installation Tool
(Supersedes TE314)
1
RC
BST-2931-1 (TE412)
1
SR25D
Step Drill
61-00-65
Page 4-12
Rev. 15 Dec/13
165A
Description:
Kit including tools and parts necessary to repair to the link pin unit safety
screw hole. Not shown. The kit contains the following:
Vendor
Vendor P/N
Hartzell P/N
Description
Qty
RC
SR192
B-6986-192 (TE422)
Slimsert®1
n/a
1/4-28 UNF-3B 99620070 (TE423)
Tap
1
RC
SR19W4-A
BST-2930-5 (TE353)
1
RC
SR19D
BST-2931-5 (TE424)
Step Drill
1
Description:
Test specimen to calibrate an eddy current instrument before its use.
AST-2979
61-00-65
Page 4-13
Rev. 15 Dec/13
165A
Ball Hex Driver
Description:
Used with 3/8 inch ratchet on the B-3812-5-16P socket head cap screw to
set preload on blade assembly.
AST3174
Shaft Nut Wrench
Part Number: BST-2910 (TE146)
Description:
Wrench to tighten the propeller mounting shaft nut on #20, #30 and #40
splined propellers.
Supersedes:
BT-2804, BT-840, BST-2804 and BST-840
61-00-65
Page 4-14
Rev. 13 Jul/12
165A
Profilometer
Description:
Used to measure surface finish in the radius and transition areas of
aluminum blade shanks. Probe Housing Component BST-3227 (TE437)
is available for use with the Hartzell Propeller Inc. and Mahr Federal
models. Stand Adapter 104371 (TE496) and Drive Housing Adapter 104372
(TE497) are available for use with the Mahr Federal Model as an alternate
to BST-3227. Use of Stand Adapter 104371 (TE496) and Drive Housing
Adapter 104372 (TE497) connect the drive unit to a standard height stand
(customer procured) without the use of BST-3227 (TE437).
Hartzell Propeller Inc. Approved Alternates:
Vendor Part Number Vendor
Perthometer 6910431
Mahr Federal Inc. (MH)
Perthometer 6910134
Mahr Federal Inc. (MH) (no longer available)
Perthometer 6910135
Mahr Federal Inc. (MH) (no longer available)
Surftest SV-600 series
Mitutoyo America Corporation (MT) (no longer available)
MarSurf PS1 6910214
TI-165005
TI-165AST3475
Perthometer 6910431
MarSurf PS1 6910214
Mahr-Federal Inc. (MH)
61-00-65
Page 4-15
Rev. 17 Dec/14
165A
Flatness Gauge
Description: Flatness gauge for steel hub flanges.
Counterweight Clamp Gauge
Description:
Gauge to locate D-1209 Counterweight Clamp on A10460E Composite
Blade.
Supersedes:BG-3445
61-00-65
Page 4-16
Rev. 12 Aug/11
165A
Clamp Nut Wrench
Description:
Wrench to hold A-1373 Clamp Nut while torquing A-1372 Bolt.
Supersedes:B-2813
Standard 12
point Socket
Special
Wrench
BST-2813
Outboard
Clamp Bolt
A-1372
Spinner Mounting Plate Bender
Part Number: BST-2823 (TE11)(CS)
Description:
Spinner mounting plate bender to achieve acceptable deice slip ring runout.
Supersedes:B-2823
61-00-65
Page 4-17
Rev. 12 Aug/11
165A
Template
Description:
Template to check minimum wall thickness of T10176( ) Blade bore.
Supersedes:B-2825
APS-488
Description:
Spring compressor to compress or decompress the feathering spring for
propeller assembly or disassembly on propeller model HC-E2Y( )-2( ).
Components: 1
2
AST-2827 (TE282) Spring Compressor Bolt
BST-2828 (TE283) Spring Compressor Slide
1
2
61-00-65
Page 4-18
Rev. 12 Aug/11
165A
Part Number: BST-2826-1 (TE31)
Description:
Spring compressor to compress or decompress the feathering spring for
propeller assembly or disassembly on propeller model number
HC-E2Y( )-2( ).
Components: 1
2
AST-2827-1 (TE284) Spring Compressor Bolt
BST-2828 (TE283) Spring Compressor Slide
BST2826A
1
2
Part Number: BST-2837 (TE6) (Includes TE385 and TE386)
Description:
Installation of the pitch change rod in compact aluminum -2 propellers. Used
with standard 1/2 inch square drive torque wrench.
Components: 1. . . . BST-2837+1+3 (TE385) Modified Socket
2. . . . BST-2837+2 (TE386) Anti-Rotation Pin
APS6259
Supersedes:BT-2837
TE385
TE386
61-00-65
Page 4-19
Rev. 12 Aug/11
165A
Probe Support
Description:
Probe support to ensure accurate contact of probe to blade surface during
Eddy Current Inspection.
Supersedes:BT-2847
Assembling Tool
Description:
Tool to assemble and disassemble the Feather Assist Spring Assembly on
the compact aluminum -2 propeller. Used with AST-2981 (TE319) Assembly
Guide.
Components:
1
2
3
4
5
6
7
B-3368 (TE387) 5/16-24 Hex Nut
BST-2850 (TE287) Threaded Rod
AST-2852 (TE288) Drilled Washer
BST-3152 (TE289) Thrust Bearing (supersedes GT-3)
BST-3151 (TE290) 5/8 Hex Nut
AST-2851 (TE291) Guide Washer
A-3204 (TE388) 5/16-24 Set Screw
6
5
2
3
1
7
4
61-00-65
Page 4-20
Rev. 12 Aug/11
165A
Torque Wrench
Description:
Wrench to tighten and torque mounting bolts on “K”, "R", or “L” flange
propellers. Used in conjunction with a standard 1/2 inch square drive
torque wrench.
Supersedes:
BST-2835 and BT-2860
Pilot Tube Puller
Description:
This part number may be used to order the drawing of the pilot tube puller
for local fabrication. Puller to remove pilot tubes from steel hub propellers.
Used in conjunction with DT-336 (TE53) or customer supplied fixture.
Supersedes:CST-2831
61-00-65
Page 4-21
Rev. 12 Aug/11
165A
Plug-Lifting Ring
Description:
Ring to thread into pitch change rod of turbine propellers for lifting and moving.
BST-2891 (TE488-1)
BST-2894 (TE488-2)
Description: Spring Compressor Base is to be used in conjunction with
CST-2914 (TE59) Spring Compressor Fixture. Refer to
CST-2914 (TE59) to determine which Spring Compressor Base (TE488-[ ])
to use with Spring Assembly type.
61-00-65
Page 4-22
Rev. 12 Aug/11
165A
Piston Fixture
BST-2892-1 (TE55)
BST-2892-2 (TE56)
Description:
HC-B3( )30-2E
ALL #20 Spline
HC-B3( )30-2B
Fixture to balance propellers. Used with some models of Marvel
Manufacturing Company balancers.
NOTE:
For left hand propeller, add L to dash number of fixture.
Supersedes:BSK-274
Part Number:
BST-2895 (TE489)
BST-2896 (TE489-1)
BST-2897 (TE489-2)
BST-2899 (TE489-3)
Description:
Spring Compressor Retainer is to be used in conjunction with
CST-2914 (TE59) Spring Compressor Fixture. Refer to CST-2914 (TE59)
to determine which Spring Compressor Retainer (TE489-[ ]) to use with
Spring Assembly type.
61-00-65
Page 4-23
Rev. 12 Aug/11
165A
Part Number:
BST-2902 (TE490)
BST-2903 (TE490-1)
BST-2904 (TE490-2)
BST-2905 (TE490-3)
BST-2907 (TE490-4)
Description:
Spring Compressor Guide Rod is to be used in conjunction with
CST-2914 (TE59) Spring Compressor Fixture. Refer to CST-2914 (TE59)
to determine which Spring Compressor Guide Rod (TE490-[ ]) to use with
Spring Assembly type.
Piston Fixture
Description:
Fixture to balance propeller models ( )HC-A3VF-4 and HC-B3WF-4.
Used with some models of Marvel Manufacturing Company balancers.
Supersedes:BSK-484
61-00-65
Page 4-24
Rev. 15 Dec/13
165A
Piston Nut Wrench
Part Number
TE Number
Description
SC058 (SO)
TE144
Wrench to tighten A-880-1 Piston Nut on a steel hub
turbine propeller. Customer procured.
SC058 (SO)
TE144-1
(Supersedes TE145)
Wrench to remove A-880-2A Piston Nut on a steel
hub turbine propeller. Customer procured.
NOTE:
TE144 and TE144-1 are the same.
Supersedes:
B-842, B-842-1, BST-2911, BST-3911-1
APS-205
61-00-65
Page 4-25
Rev. 12 Aug/11
165A
Part Number:
BST-2912 (TE125)
Building Buck Components, includes items 1 through 9 listed below
Item Number Part Number Description
1�� BST-2912+ (TE125-1)
2�� BST-2912-1 (TE124)
3�� BST-2912-2 (TE122)
4�� BST-2912-3 (TE123)
5�� BST-2912-4 (TE4)
6�� BST-2912-9 (TE2)
7�� BST-2912-11 (TE85)
8�� BST-2912-12 (TE127)
9�� BST-2912-13 (TE327)
Spindle Base; Supersedes: B-843-2 (Includes TE85)
Flanged Hub Spindle (Includes TE4)
Supersedes: BST-2812
#20 Spline Spindle; not shown
#30 Spline Spindle; not shown
Adapter Ring; Permits mounting of “N” flange
propellers
Adapter; Permits mounting of “A” flange single
acting propellers
Stop Pin; not shown
Mid Pitch Stop; Supersedes: BT-2162; not shown
Blade Angle Stop for -5 Propellers; not shown
Also available as necessary (not a part of BST-2912 (TE125):
BST-2912-10 (TE80) “C” Flange Spindle; allow mounting of “C” flange HD-E6C-3 propeller; not shown
BST-2912-17 (TE433) “A” Flange Spindle; allow mounting of “A” flange HC-E5A-2 propeller; not shown
BST-2912-19 (TE536) “H”, “T”, “Q”, and “G” Flange Spindle; allow mounting of “H”, “T”, “Q”,
and “G” flange propellers; shown on page 4-148 of this manual
BST-2912-22 (TE550) “F” Flange Bantam Adapter Ring; shown on page 4-153 of this manual
Description: Spindle mounts to propeller assembly table CST-2901(-) (TE129) to permit
pressurizing of propeller to change pitch. Also permits rotating of the propeller.
Obsolete:
BST-2912-8 (TE1)
Adapter; Allow mounting of “C” flange single acting propellers; not shown
BST-2912-9
Adapter
BST-2912-4
Adapter Ring
APS-546
BST-2912-1
Flanged Hub
Spindle
BST-2912+
Spindle Base
61-00-65
Page 4-26
Rev. 17 Dec/14
165A
Drill Fixture
Description:
Fixture to modify C-3201 Piston for installation of external feather stop.
Description:
Wrench to remove, install and torque cylinders on aluminum hub propellers.
Supersedes:BST-2801
APS-175
61-00-65
Page 4-27
Rev. 12 Aug/11
165A
Description:
Modified socket to remove, install and torque piston mounting nuts on
light-weight turbine propellers.
Pitch
Change
Rod
APS-152
Modified Deep Well
Socket No. BST-2922
Piston
Dummy Pitch Change Rod
Description:
Used during assembly of the HC-A6A-3 propeller.
61-00-65
Page 4-28
Rev. 12 Aug/11
165A
Shot Peen Plug
Description:
Plug to mask the blade bore prior to shot peening on “Y” shank blades.
Part Number
TE Number
Description
BST-3067
TE228
Modified socket to install and remove piston on
D-6071 and D-494 pitch change rods.
BST-3067+3
TE228-1
Modified socket to install and remove piston on
a D-3657 pitch change rod.
61-00-65
Page 4-29
Rev. 12 Aug/11
165A
Shot Peen Plug
Part Number: BST-2939N (TE89)
Description:
Plug to mask the blade bore prior to shot peening on “M” and “T” shank
blades, with “N” modifications.
Shot Peen Plug
Description:
Plug to mask the blade bore prior to shot peening on “E” shank blades.
61-00-65
Page 4-30
Rev. 12 Aug/11
165A
Shot Peen Plug
Description:
Plug to mask the blade bore prior to shot peening on “W” shank blades.
Part Number:
BST-2942 (TE13)
BST-2943 (TE14)
BST-2944 (TE15)
BST-2945 (TE16)
Description:
Cap to protect blade shank and bore during shipping and storage.
BST-2942 is shown.
“T,” “S” and “M” Shanks
“V,” “MV”, “N” and “X” Shanks
“W,” “R,” “Z” and “P” Shanks
“D” and “Y” Shanks
61-00-65
Page 4-31
Rev. 15 Dec/13
165A
Shot Peen Plug
Description:
Plug to mask the blade bore prior to shot peening on “P” and “Z” shank
blades.
Bushing Puller
Description:
Puller to remove A-1347 and A-1309 Bushings. Used in conjunction with
customer supplied hydraulic or pneumatic puller.
61-00-65
Page 4-32
Rev. 12 Aug/11
165A
Bearing Puller
Description:
Puller to remove A-127, A-127-1, and A-1497 bearings. Used in conjuntion
with customer supplied hydraulic or pneumatic puller.
Bearing Puller
Description:
Puller to remove bearings from “M,” “S,” “T” and “W” shanks. Used in
conjunction with a customer supplied hydraulic or pneumatic puller.
APS-494
61-00-65
Page 4-33
Rev. 12 Aug/11
165A
Bearing Puller
Description:
Puller to remove bearings from “M” and “T” shanks. Used in conjunction
with a customer supplied hydraulic or pneumatic puller.
APS-900
Bearing Puller
Description:
Puller to remove bearings from “D,” “Y” and “V” shanks.
Supersedes:CST-2838
61-00-65
Page 4-34
Rev. 12 Aug/11
165A
Pitch Angle Stop Plug
Description:
Plug to block the end of the pitch change rod to allow actuation of the propeller
on the bench.
Hoist Ring Combo
Part Number: BST-2958L (TE62)
Description:
Combination tool to lift and move propellers. Also, to seal the end of pitch
change rods and actuation of propellers on the bench.
61-00-65
Page 4-35
Rev. 12 Aug/11
165A
Alignment Check Rod
Description:
Rod to check concentricity of the inner threads of the B-3018 or B-1948 Rod.
Supersedes:B-1509
Digital Protractor
Description:
Protractor to measure blade angles. May be used to check angles with
propeller installed on engine. Protractor includes protractor case.
Supersedes:
BST-2960-1, BST-2960-2, BST-2820, and CST-2880
NOTE: Locally procured and calibrated bubble protractor accurate to within 0.1 degree may be used and is considered equivalent.
BST-2960
APS0336
Protractor Case
61-00-65
Page 4-36
Rev. 12 Aug/11
165A
Thickness Gauge
Description:
Gauge to inspect thickness of 13/4 I.D. on M10876 Blade.
61-00-65
Page 4-37
Rev. 14 Jun/13
165A
Ream Fixture
Description:
Fixture is to locate and drill spinner support plates.
Part Number:
BST-2966 (TE181)
BST-2966-3 (TE182)
BST-2966-4 (TE183)
BST-2966-5 (TE184)
Description
C-3733 “A” Flange, 5 Way C-3003-1, 3 Way C-3404, 4 Way C-4011-5, 5 Way Supersedes
BT-2723
BST-2836, CT-1472
CT-1482
BST-2848
Part Number:
Description:
BST-2974 (TE161)
LM10585(A)(N)(B,K)+4
BST-2974-1 (TE162)
M10877
BST-2974-2 (TE163)
M10083
BST-2974-3 (TE164)
B7421
BST-2974-4 (TE165)
A10460(E)
BST-2974-5 (TE541)
B7466
BST-2974-6 (TE542)
E11990
BST-2974-7 (TE168)
E10950P(C)( )
BST-2974-8 (TE543)
E13482
BST-2974-9 (TE544)
E12902
BST-2974-10 (TE545)
E13890K
BST-2974-11 (TE546)
( )7690( )
Clamp to prevent wrinkling of fiberglass during erosion shield bonding on
composite blades.
61-00-65
Page 4-38
Rev. 15 Dec/13
165A
Fit Check Tool
Part Number:
BST-2975 (TE171)
BST-2975-1 (TE172)
BST-2975-2 (TE173)
BST-2975-3 (TE174)
BST-2975-4 (TE175)
BST-2975-6 (TE177)
BST-2975-7 (TE178)
BST-2975-9 (TE180)
BST-2975-10 (TE340)
BST-2975-12 (TE377)
BST-2975-13 (TE378)
BST-2975-14 (TE480)
BST-2975-15 (TE549)
BST-2975-16 (TE481)
BST-2975-17 (TE482)
BST-2975-18 (TE483)
BST-2975-19 (TE484)
BST-2975-20 (TE485)
BST-2975-21 (TE511)
BST-2975-22 (TE512)
BST-2975-23 (TE513)
BST-2975-24 (TE514)
BST-2975-25 (TE515)
BST-2975-26 (TE552)
BST-2975-27 (TE553)
BST-2975-30 (TE554)
BST-2975-31 (TE555)
BST-2975-32 (TE556)
BST-2975-33 (TE557)
BST-2975-34 (TE558)
Description:
Blade
LM10585AN+4
M10877
M10083
B7421
A10460E
E11990
E10950
E12902
E13890K
7890K
7690E
N7605 & N7605C
E9193( )
N7893
N7605-2
N7605+2
N7605-4
NC9208
NG8301
NC8834
(H)79A06
(L,J)76A01-2
(H)75A01-2
NG8301-5
NC8301-7
108MH92
138MH91
NG8301-1
NG8301-3
E8190
Erosion Shield Reference
D-5019
D-5003
D-5013
D-5069
D-5059
D-5072
D-5133
D-2833
D-6221
D-6763
D-6015-2
101622
100515
101181
101622-2
101622+2
101622-4
102227
104595
104926
100503
104639
104772-2
104595-5
104595-7
D-6221-1
105448
104595-1
104595-3
D-4786
Tool to check fit of erosion shield before installation on composite blades.
61-00-65
Page 4-39
Rev. 17 Dec/14
165A
Drill Jig
Description:
Drill jig for “N” flange slimsert installation.
Drill Jig
Description:
Drill jig for “F” flange slimsert installation.
61-00-65
Page 4-40
Rev. 12 Aug/11
165A
Alignment Check Rod
Description:
Rod to check concentricity of internal threads of D-494 Pitch Change Rod.
Part Number
TE Number
Description
BST-2985
TE64
Tool to install the blade alignment bearings in
T and M shank blades with N modification.
Used in conjunction with customer supplied
hydraulic or pneumatic press.
BST-2985-1
TE64-1
Tool to install the blade alignment bearings in
R and W shank blades with N modification.
Used in conjunction with customer supplied
hydraulic or pneumatic press.
BST-2985,-1
BST-2985
BST-2985-1
61-00-65
Page 4-41
Rev. 12 Aug/11
165A
Template
Part Number:
BST-3004 (TE219)
BST-3004-1A (TE220)
BST-3004-1B (TE221)
BST-3004-2A (TE222)
BST-3004-2B (TE223)
BST-3004-3A (TE224)
BST-3004-3B (TE225)
BST-3004-4A (TE226)
BST-3004-4B (TE227)
BST-3004-6A (TE230)
BST-3004-6B (TE231)
BST-3004-7A (TE232)
BST-3004-7B (TE233)
BST-3004-9A (TE236)
BST-3004-9B (TE237)
BST-3004-10A (TE335)
BST-3004-10B (TE336)
BST-3004-11A (TE337)
BST-3004-11B (TE338)
BST-3004-12A (TE461)
BST-3004-12B (TE462)
BST-3004-13A (TE463)
BST-3004-13B (TE464)
BST-3004-14A (TE465)
BST-3004-14B (TE466)
BST-3004-15A (TE467)
BST-3004-15B (TE468)
BST-3004-16A (TE469)
BST-3004-16B (TE470)
BST-3004-19A (TE471)
BST-3004-20A (TE472)
BST-3004-20B (TE473)
BST-3004-21A (TE521)
BST-3004-21B (TE522)
BST-3004-22A (TE523)
BST-3004-22B (TE524)
BST-3004-23A (TE525)
BST-3004-23B (TE526)
BST-3004-24A (TE527)
BST-3004-24B (TE528)
BST-3004-25A (TE529)
BST-3004-25B (TE530)
48 inch station of LM10585
42 inch station of M10877
52 inch station of M10877
39.75 inch station of M10083
47.25 inch station of M10083
30 inch station of B7421
34 inch station of B7421
30 inch station of A10460
48 inch station of A10460
42 inch station of E11990
30 inch station of 7890
36 inch station of 7890
30 inch station of N7605
36 inch station of N7605
30 inch station of N( )7893
36 inch station of N( )7893
24 inch station of N7605-4
30 inch station of NC9208
30 inch station of NG8301
36 inch station of NG8301
30 inch station of ( )79(A/B)06
36 inch station of ( )79(A/B)06
30 inch station of ( )76(A/B)01-2
Description:
Tool to check stations of composite blades.
BST-3004
61-00-65
Page 4-42
Rev. 17 Dec/14
165A
Part Number: Description:
BST-3019 (TE112)
Tool to remove B-1243 threaded staked insert.
BST-3019-3 (TE112-1)
Tool to remove B-1243-1 threaded staked insert.
BST-3019-4 (TE112-3)
BST-3019-8 (TE112-4)
Blade Assembly Support Stand
Description:
Stand to support blade in hub during HD-E6C-3 or HC-E4N-3A propeller
assembly.
61-00-65
Page 4-43
Rev. 13 Jul/12
165A
Bearing Press
BST-3026-2 (TE239)
BST-3026-3 (TE240)
Description:
1.000 inch O.D.
1.500 inch O.D.
1.625 inch O.D.
Press used to install bearings into bearing carriers or housings during
assembly of HD-E6C-3 propeller or PCU.
Modified Crowfoot
Description:
Modified 15/16 inch, 3/8 inch drive crowfoot wrench.
61-00-65
Page 4-44
Rev. 12 Aug/11
165A
Modified Crowfoot
Description:
Modified 113/16 inch, 3/8 inch drive crowfoot wrench.
Modified Crowfoot
Description:
Modified 13/4 inch, 3/8 inch drive crowfoot wrench used during assembly and
disassembly of HD-E6C-3 propeller.
61-00-65
Page 4-45
Rev. 12 Aug/11
165A
Open End Wrench
Description:
Modified 13/4 inch open end wrench.
Modified Crowfoot
Description:
Modified 17/16 inch crowfoot adapter to remove, install and torque pitch
change rod or hydraulic assembly into pitch change fork of HD-E6C-3
propeller. If propeller has been subjected to pitch lock, use BST-3044.
61-00-65
Page 4-46
Rev. 12 Aug/11
165A
Adapter
Description:
Adapter to remove or install the front bearing nut in the HD-E6C-3 propeller.
Description:
Cone used to compress O-rings and seals installed on PCU servo piston to
allow ease of installation into PCU servo column.
61-00-65
Page 4-47
Rev. 12 Aug/11
165A
Aft Control Spring Compressor
Description:
Tool to be used in conjunction with customer supplied press to push against
spacer in order to compress aft spring of HD-E6C-3 propeller. This allows
installation of spacer retaining ring.
Description:
Used to re-align the control rod to control valve in the HD-E6C-3 propeller.
61-00-65
Page 4-48
Rev. 12 Aug/11
165A
Bearing Puller
Description:
Puller to remove pitch lock bearing and carrier from pitch lock bearing housing
of HD-E6C-3 propeller.
Rigging Pin
Description:
Rigging pin, 3/16 inch diameter, to hold PCU and CSU power and condition
levers in the correct position for rigging. (Two required.)
61-00-65
Page 4-49
Rev. 12 Aug/11
165A
Clamp Wrench
Description:
Wrench to remove pitch change rod or hydraulic assembly from pitch change
fork of HD-E6C-3 propeller after pitch lock.
Puller
Description:
Puller to remove bearings from pitch change brackets, O-ring plugs from
extended hub compact propellers, etc.
61-00-65
Page 4-50
Rev. 12 Aug/11
165A
Threaded Insert Installation Tool
Part Number: Description: Supersedes:
BST-3047 (TE68)
Tool to install B-1243 threaded staked insert. AT-2422, KHT9000-9
BST-3047-1 (TE68-9)
Tool to install B-6143 threaded staked insert.
BST-3047-2 (TE68-8)
Tool to install B-6143-4 threaded staked insert.
BST-3047-3 (TE68-3)
Tool to install B-6143-4H threaded staked insert.
BST-3047-4 (TE68-4)
BST-3047-5 (TE68-5)
BST-3047-6 (TE68-6)
BST-3047-7 (TE68-7)
BST-3047-8 (TE68-1)
Tool to install B-6143-8H threaded staked insert.
Description:
Installation of transfer tube and removal of transfer tube and plug in HD-E6C-3
propeller.
61-00-65
Page 4-51
Rev. 12 Aug/11
165A
Chip Detector Fitting
Description:
Chip Detector Fitting used with DST-3049-( ) (TE318) Ground Hydraulic
Power Unit.
Chip Detector Fitting Cover
Description:
Cover for BST-3050 Chip Detector Fitting on DST-3049-( ) Ground
Hydraulic Power Unit.
61-00-65
Page 4-52
Rev. 12 Aug/11
165A
Description:
Tool used to align and install PCU manifold insert into PCU manifold/servo
column.
BST-3055-1 (TE186)
Description:
For B-6133-1 Bearing
For B-6133-2 Bearing
Tool used in conjunction with customer supplied press to install roller bearings
into PCU manifold.
61-00-65
Page 4-53
Rev. 12 Aug/11
165A
Description:
Tool used in conjunction with customer supplied press to install oil lite
bushings into PCU manifold.
Description:
Tool used in conjunction with customer supplied press to install oil lite
bushings into PCU manifold.
61-00-65
Page 4-54
Rev. 12 Aug/11
165A
Shot Peen Masking Tool
Description:
Screw to mask 1/2-28 helicoil holes during shot peening.
Screw Driver
Description:
Screw driver to drive BST-3060 Screw.
61-00-65
Page 4-55
Rev. 12 Aug/11
165A
Press Tool
Description:
Used to press split bearings in steel hub propellers.
Supersedes:BT-222-1
Press Tool
Description:
Used to press split bearings in steel hub propellers.
Supersedes:BT-222
61-00-65
Page 4-56
Rev. 12 Aug/11
165A
Pilot Tube Installation Tool Kit
Description:
Tool set contains various spacer adapters. Refer to TE52 for the fixture to
be used with customer procured hydraulic press.
Kit Part Number:
BST-3064 (TE241)
BST3064-1 (TE242) can only be used with a hydraulic press that
accepts a ram adapter that is 0.75 inch (19.0 mm) diameter by
1.25 inches (31.7 mm) long. For other hydraulic presses, the
ram adapter is customer procured.
Kit with the Pilot Tube Installation Tool includes:
Components
1 BST-3064-1 (TE242)
Pilot Tube Installation Tool
(May be purchased separately.)
2....BST-3064-2 (TE243)
Pilot Tube Positioner & Stop
3....BST-3064-3 (TE244)
4....BST-3064-4 (TE245)
5....BST-3064-5 (TE246)
Supersedes:B-844
BST-3064A (TE241-1) Kit without the Pilot Tube Installation Tool includes:
Components
1....BST-3064-2 (TE243)
2....BST-3064-3 (TE244)
3....BST-3064-4 (TE245)
4....BST-3064-5 (TE246)
BST-3064-1
BST-3064-2
HC-B( )( )( )
BST-3064-3
HC-9( )2( )-( )
BST-3064-4
HC-A( )( )( )
HC-D( )( )( )
BST-3064-5
HC-8( )X( )-( )
61-00-65
Page 4-57
Rev. 12 Aug/11
165A
Blade Shot Peen Plug Removal Tool
Description:
Tool to remove shot peen plugs.
Chamfering Tool
Description:
A six fluted, 45 degree chamfering tool used to chamfer grease fitting holes in
aluminum hubs (reference Hartzell Service bulletin No. 165E or subsequent
revision).
BST-5845
61-00-65
Page 4-58
Rev. 15 Dec/13
165A
Description:
Tool to protect O-ring when it is installed over the HD-E6C-3 propeller oil
transfer tube.
Description:
Installation of beta valve assembly in the PCU.
61-00-65
Page 4-59
Rev. 12 Aug/11
165A
Description:
Fixture to set PCU piston indicating rod at the pre-set flight idle position.
Description:
Used in the assembly and disassembly of HD-E6C-3 propeller.
61-00-65
Page 4-60
Rev. 12 Aug/11
165A
Beta Switch Tester
Description:
Test box to simulate the cockpit beta light when rigging the PCU beta light
switch during PCU assembly. To be used in conjunction with BST-10006
Rigging Cover.
BST-10005
STAND-BY
BETA
ON
OFF
HARTZELL
BST-10005
Rigging Cover
Description:
Cover used to actuate the PCU beta light switch at pre-set position to assist in
beta light switch rigging. To be used in conjunction with BST-10005 Beta Light
Switch Test Box.
BST-10006A
BST-10006B
61-00-65
Page 4-61
Rev. 15 Dec/13
165A
Description:
These pins are threaded into the hub's forward mounting ring to hold it in the
correct position for:
1) Hydraulic unit mounting during HD-E6C-3 propeller assembly (four
required).
2) Cylinder mounting during the HC-E5A-2 propeller assembly (2 required).
Strap Wrench
Part Number: 100923 (TE148-1)
Description:
Wrench to install/remove feathering spring.
Supersedes:
BT-461 (TE148)
100923
61-00-65
Page 4-62
Rev. 15 Dec/13
165A
Retention Bearing Puller
Part Number: BT-223 (TE108)
Description:
Puller to remove and install bearings on steel hub spiders. Used in conjunction
with BST-3061 and BST-3062. Adaptors used as listed.
Adaptors: BT-223+9 (TE108-1) (CS)
Adaptor ring used when removing
the A-1852 bearing retaining ring.
NOTE:
This part number may be
used to order the drawing to
BT-223+10 (TE108-2) (CS)
Adaptor ring used when removing
the A-972 bearing retaining ring.
NOTE:
This part number may be
used to order the drawing to
APS-189-1
Adaptor BT-223+9 (TE108-1)
or BT-223+10 (TE108-2)
Bearing Retaining Ring
BST-3061 (TE308) or BST-3062 (TE309)
to pull bearing retaining ring into position
61-00-65
Page 4-63
Rev. 12 Aug/11
165A
Shot Peen Tube Assembly
Part Number: BT-1271-1,2 (TE137)
BT-1271-1 Fine Threads
BT-1271-2 Coarse Threads
Description:
Adapter assembly to shot peen blade balance bores. Used with CT-1311 (TE12).
Supersedes:BT-1271
BT-1271-1_2
Shot Peen Tube Assembly (TE137)
Shot Nozzle Unit (TE494)
(not included)
Shot Peen Gun (TE379)
(not included)
Shot Nozzle Unit
Part Number
TE Number
BT-1271-4 BT-1271-5 BT-1271-6 BT-1271-7 BT-1271-8 (TE494)
(TE494-1)
(TE494-2)
(TE494-3)
(TE494-4)
1.95 inches (49.5 mm)
3.34 inches (84.8 mm)
4.72 inches (119.8 mm)
6.10 inches (154.9 mm)
10.10 inches (256.5 mm)
Description:
Used with Shot Peen Cabinet CT1311 (TE12), Shot Peen Gun 02643
(TE379), Shot Peen Tube Assembly BT-1271(-1,or-2) (TE137)
Length
Length
61-00-65
Page 4-64
Rev. 12 Aug/11
165A
Almen Strip Fixture
Part Number: 104381 (TE49)
Description:
Fixture to confirm shot intensity in the lead hole of a blade.
Supersedes:BT-1312
TI-165006,7
Shot Peen Cabinet
Part Number: CT-1311 (TE12) (CS)
Description:
This part number may be used to order the drawing of the shot peen cabinet
for local fabrication. Cabinet to house and support the blade during lead hole
shot peening. Used with BT-1271 (TE137), BT-1312 (TE49), BT-1271-( )
(TE494-[ ])and 02643 (TE379).
APS-180A
61-00-65
Page 4-65
Rev. 15 Dec/13
165A
Eddy Current Probe Unit
Description:
Probe for Eddy Current inspection of blade balance hole.
Part Number: BT-1313 (TE95) No longer available from Hartzell Propeller Inc.
Order from vendor (See below)
Superseded by Olympus NDT Inc. Part Number BT-1313(-)( ) (TE95)
Part Number: Olympus NDT Inc. Part Number BT-1313(-)( ) (TE95)
NOTE:
There are three versions of the eddy currect probe unit available
from Olympus NDT Inc. Refer to the chart.
Supersedes:
BT-1313 (Hartzell Part Number)
Vendor:
Olympus NDT Inc. (OL)
Olympus NDT Inc. Part Number
Connector Type
BT-1313
1/4" Headphone
BT-1313-1
Microdot
BT-1313-2
Triax Fischer/Lemo
Connector
(see chart)
Probe
(included)
Probe Collar
(included)
TI-165001,2,3
1/4" Headphone
Microdot
Triax Fischer/Lemo
Connector Types
61-00-65
Page 4-66
Rev. 12 Aug/11
165A
Floating Reamer
Part Number: BT-1465-1 (TE207)
BT-1465-3 (TE207-1)
0.766 (19.45 mm) diameter ball nose
BT-1465-2 (TE208)
BT-1465-4 (TE208-1)
Description:
Reamer to repair a blade balance hole.
Floating reamer holder not supplied
by Hartzell Propeller Inc.
61-00-65
Page 4-67
Rev. 12 Aug/11
165A
Stop Adapter
Description:
Adapter to push pilot tubes deeper into the hub in order to remove with less
force.
Peening Tool
Description:
Tool for peening A-2245-(1) bushings in aluminum hubs.
61-00-65
Page 4-68
Rev. 12 Aug/11
165A
PCU Bearing Seat Sander
Description:
Tool for sanding the O.D. bearing seat surface on Propeller Control Unit.
3009.TIF
Description:
Eddy current probe support fixture for inspecting "X" and "V" shank double
shoulder aluminum propeller blades. (Does not include probe. Standard
1
/8 inch pencil probe is recommended.)
APS-2079
Eddy Current
Probe
TE315
61-00-65
Page 4-69
Rev. 12 Aug/11
165A
Drill Jig (PCU)
Description:
Drill jig for removing the PCU manifold plug from Propeller Control Unit.
BST-3070.ai
PCU Stand
Description:
Stand for securing Propeller Control Unit during maintenance operations.
BST3071.TIF
61-00-65
Page 4-70
Rev. 15 Dec/13
165A
Centering Tool for C-5623-2 Drive Coupling
Description:
Tool for aligning the drive coupling in the PCU manifold.
BT3035.TIF
E13890 Master Blade
Part Number: BST-3200 (TE431) - Group 0 (-100 in. oz.)
BST-10037 (TE299) - Group 1 (-5 in. oz.)
BST-10038 (TE300) - Group 2 (+100 in. oz.)
BST-10039 (TE301) - Group 3 (+180 in. oz.)
102690 (TE460) - Group 4 (+260 in. oz.)
Description:
Used to balance composite blades into balance groups. Not shown. The
part numbers above may be used to order the drawing of the master blade
for local fabrication.
61-00-65
Page 4-71
Rev. 15 Dec/13
165A
Modified Crowfoot
Description:
Modified 1¼ inch, 3/8 inch drive crowfoot wrench used to adjust the pitch
lock gap on the HD-E6C-3( ) propeller.
Pitch Lock Roller Fixture
Description:
Used to compress A-5654-1 pitch lock unit to facilitate disassembly/
assembly.
61-00-65
Page 4-72
Rev. 12 Aug/11
165A
Shot Peen Plug
Description:
Plug to mask the blade bore prior to shot peening on “X” shank, “X” shank
modified to “V” shank, “V” shank, “V” shank blades with “N” modification and
“MV” shank blades with “N” modification. Used with TE372 as required.
Shot Peen Plug
Description:
Used with TE371 to mask the blade bore prior to shot peening on “V” shank
blades with “N” modification and “MV” shank blades with “N” modification.
61-00-65
Page 4-73
Rev. 12 Aug/11
165A
T-Handle Wrench
Description:
Installation of the stop screw in compact aluminum -2 propellers.
APS6262
Feathering Tool
Description:
Tool used to install the pitch adjustment washers and feathering stop in
compact aluminum -2 propellers.
APS6262
61-00-65
Page 4-74
Rev. 12 Aug/11
165A
Cylinder Installation Rod
Description:
Tool used to spread the start lock mechanism when installing the cylinder in
compact aluminum feathering propellers.
APS6261
Reamer
Part Number: BST-3022 (TE403) - All Compact and "H" and "Q" Bantam propeller hubs
with 1/2-20UNF studs
BST-3022A (TE403-1) - Bantam propeller hubs with 7/16-20UNF studs
Description:
Used to remove adhesive from the bottom of hub mounting stud holes.
BST3022
61-00-65
Page 4-75
Rev. 17 Dec/14
165A
Shot Peen Plug
Description:
Plug to mask the blade bore before shot peening “M” and “T” shank blades
that do not have “N” modifications.
BST2939
Bearing Puller
Description:
Puller to remove bearings from "E" shanks. Used in conjunction with
customer supplied hydraulic or pneumatic puller.
NOTE: Use only with bearings having a cage and a flat bottomed closed end. This puller will not work on bearings with a full complement of needles and a dimpled closed end.
BST2951
61-00-65
Page 4-76
Rev. 12 Aug/11
165A
Paint Mask Cap
Part Number: BST-3006 (TE414) diameter of "A" is 5.930 inches (15.06 cm)
BST-3158 (TE415) diameter of "A" is 6.345 inches (16.12 cm)
Description:
Used to mask the cylinder attachment thread area of aluminum hubs.
"A"
61-00-65
Page 4-77
Rev. 12 Aug/11
165A
Spacer
Description:
Used during assembly for set up of 2-way Hydro-Selective propellers.
BST2991
Mask Screw
Description:
Screw to mask shot peen from the lubrication fitting hole in an aluminum hub.
BST3081
61-00-65
Page 4-78
Rev. 12 Aug/11
165A
Blade Pitch Fixture
Description:
Tool that attaches to the blade for blade angle check.
TI-BST-3226
Probe Housing Component
Description:
Used to support the probe of the profilometer when performing the surface
finish inspection in the radius and transition areas of aluminum blade shanks.
Used with AST-3475 (TE436), as necessary.
BST-3227
61-00-65
Page 4-79
Rev. 17 Dec/14
165A
Part Number:
BST-3177 (TE440)
For four-bladed lightweight turbine propellers
BST-3063 (TE440-1)
For five-bladed lightweight turbine propellers
Description:
Used during assembly to aid installation of the blade seal.
BST3177
Composite Balance Tube Puller
Description:
Tool to remove composite blade balance tube.
BST4114
61-00-65
Page 4-80
Rev. 12 Aug/11
165A
Grease Seal Pressure Test Tool (Adapter)
Description:
Used with TE382 (DST-3146) Thread Gauge Airflow Kit to perform grease
seal pressure test.
NOTE: Use with O-rings C-3317-010-2 and C-3317-08-2, not supplied.
BT-3838
Grease Seal Pressure Test Tool
Part Number: BT-3838-1 (TE443-1)
Description:
Used with TE382 or TE382-1 Thread Gauge Airflow Kit to perform grease
seal pressure test.
NOTE: BT-3838-1 (TE443-1) eliminates the need for using both the
CST-3117 Probe Assembly and BT-3838 (TE443) to check
grease seal pressure.
BT-3838-1A
61-00-65
Page 4-81
Rev. 15 Dec/13
165A
Pressure Check Tool
Part Number: BST-7587 (TE441)......... For K, R, L, and F flange
BST-7587-1 (TE441-1)... For N flange
BST-7587-2 (TE441-2)... For Q flange
Description:
Used to perform a leak inspection after repair of the pitch change rod bore of
an aluminum hub.
NOTE:
This part number may be used to order the drawing to allow for local fabrication.
BST-7587
BST-7587-2
Insert Installation Tool
Description:
Used to provide a location of depth of the flange mounting inserts during the
adhesive cure process.
NOTE:
This part number may be used to order the drawing to allow for local fabrication.
BST-7588
61-00-65
Page 4-82
Rev. 15 Dec/13
165A
Stud Fixture Plate
Part Number: CST-421 (TE487)
Description:
A tool used when installing studs in D-flange, F-flange, N-flange, and
W-flange hubs to make sure that the studs are set perpendicular to the hub
flange.
CST-421
Description:
Clamp to hold the blade retention components onto the blade shank for
installation into the hub. Designed to fit “D” and “Y” shank blades.
APS-162
61-00-65
Page 4-83
Rev. 12 Aug/11
165A
Pilot Tube Press Fixture
Description:
Fixture to securely hold the propeller hub during pilot tube installation.
The press is customer procured. Press must be capable of generating up
to 25 tons of force, have an adjustable press opening height, and at least
3.5 inches (88.9 mm) of stroke.
Supersedes: B-843-2
APS197-1
Hydraulic
Press Ram
Tool No.
BST-3064-( )
(TE243 through TE246,
sold separately)
Customer-procured
Support Plate
Pilot Tube Assembly Tool (TE242)
(*May be purchased separately.)
Hub Pilot
Tube
Endplate of Pilot
Tube Fixture
CST-2913
* TE242 can only be used with a hydraulic press that accepts a ram adapter
that is 0.75 inch (19.0 mm) diameter by 1.25 inches (31.7 mm) long. For
other hydraulic presses, the ram adapter is customer procured.
61-00-65
Page 4-84
Rev. 12 Aug/11
165A
WARNING:
USE EXTREME CAUTION DURING DISASSEMBLY. THE FEATHERING
SPRING ASSEMBLY MAY BE PRELOADED TO OVER 2000 POUNDS
FORCE.
Description:
Fixture to compress the feathering spring sufficiently to allow assembly or
disassembly of the spring assembly.
NOTE: This fixture is not to be used on 5 and 6 Way propellers with an “E” or “A”
shank. The fixture to be used for “E” shanks is CST-3016 (TE32) and the
fixture for “A” shanks is customer supplied.
Supersedes:
CSD-4900, C-845-2
APS-545
The following tooling is required in addition to the CST-2914 Spring Compressor Fixture
depending upon the type of Spring Assembly:
Spring Assembly Base
Retainer
Guide Rod
831-1A
831-2
831-3
831-4
831-5A, B, C
831-6
831-7
831-8
831-9
831-10
831-11
831-12
BST-2895 (TE489)
BST-2899 (TE489-3)
BST-2895 (TE489)
BST-2895 (TE489)
BST-2895 (TE489)
BST-2895 (TE489)
BST-2899 (TE489-3)
BST-2895 (TE489)
BST-2899 (TE489-3)
BST-2899 (TE489-3)
BST-2899 (TE489-3)
BST-2897 (TE489-2)
BST-2907 (TE490-4)
BST-2905 (TE490-3)
BST-2907 (TE490-4)
BST-2907 (TE490-4)
BST-2907 (TE490-4)
BST-2907 (TE490-4)
BST-2905 (TE490-3)
BST-2904 (TE490-2)
BST-2905 (TE490-3)
BST-2905 (TE490-3)
BST-2905 (TE490-3)
BST-2902 (TE490)
BST-2894 (TE488-2)
BST-2890 (TE488)
BST-2894 (TE488-2)
BST-2894 (TE488-2)
BST-2894 (TE488-2)
BST-2894 (TE488-2)
BST-2890 (TE488)
BST-2890 (TE488)
BST-2890 (TE488)
BST-2890 (TE488)
BST-2891 (TE488-1)
BST-2890 (TE488)
61-00-65
Page 4-85
Rev. 15 Dec/13
165A
Part Number: CST-2914 (TE59)..... Con’t
Retainer
Guide Rod
831-13
BST-2891 (TE488-1) BST-2899 (TE489-3) BST-2905 (TE490-3)
831-14
BST-2894 (TE488-2) BST-2895 (TE489)
BST-2907 (TE490-4)
831-15
BST-2891 (TE488-1) BST-2899 (TE489-3) BST-2905 (TE490-3)
831-16BST-2890 (TE488)BST-2899 (TE489-3)BST-2905 (TE490-3)
831-16ABST-2890 (TE488)BST-2899 (TE489-3)BST-2905 (TE490-3)
831-19BST-2890 (TE488)BST-2895 (TE489)BST-2902 (TE490)
831-20BST-2894 (TE488-2)BST-2895 (TE489)BST-2903 (TE490-1)
831-21BST-2894 (TE488-2) BST-2896 (TE489-1) BST-2903 (TE490-1)
831-22BST-2890 (TE488)
BST-2896 (TE489-1) BST-2902 (TE490)
831-23BST-2894 (TE488-2)BST-2895 (TE489) BST-2902 (TE490)
831-23ABST-2890 (TE488)BST-2895 (TE489) BST-2902 (TE490)
831-24BST-2890 (TE488)BST-2895 (TE489)BST-2903 (TE490-1)
831-26BST-2890 (TE488)BST-2895 (TE489) BST-2903 (TE490-1)
831-35BST-2891 (TE488-1)BST-2899 (TE489-3)BST-2905 (TE490-3)
831-41BST-2890 (TE488)
BST-2896 (TE489-1) BST-2902 (TE490)
831-42BST-2890 (TE488)
BST-2896 (TE489-1) BST-2902 (TE490)
831-44BST-2890 (TE488)
BST-2896 (TE489-1) BST-2903 (TE490-1)
61-00-65
Page 4-86
Rev. 15 Dec/13
165A
Part Number: CST-2914 (TE59)..... Con’t
Retainer
Guide Rod
831-47BST-2890 (TE488)BST-2895 (TE489)BST-2902 (TE490)
831-48BST-2894 (TE488-2)BST-2895 (TE489) BST-2904 (TE490-2)
831-55BST-2890 (TE488)
BST-2896 (TE489-1) BST-2903 (TE490-1)
831-56BST-2890 (TE488)BST-2897 (TE489-2)BST-2902 (TE490)
831-58BST-2890 (TE488)
BST-2896 (TE489-1) BST-2903 (TE490-1)
Balance Arbor
Description:
Used to determine the location of the static balance weights on a completed
propeller assembly. Used with customer supplied balance units. Works with
2 to 5 bladed propellers with “F,” “K,” “L,” “N” and “R” flanges.
Supersedes:
CT-2210 and CSK-155
CST-2919
Includes
2 Flanges
61-00-65
Page 4-87
Rev. 15 Dec/13
165A
“D” and “Y” Shanks
CST-2924 (TE19)
“X,” “V” and “N” Shanks
CST-2925 (TE20)
“Z,” “W,” “T” and “S” Shanks
CST-2926 (TE21)
“M,” “R” and “P” Shanks
CST-2989 (TE22)
“E” Shank
CST-10050 (TE373)
"MV" Shanks
Description: A 14 inch (355.6 mm) clear overlay to check the condition and repairability
of an aluminum blade retention radius. Used with customer supplied
optical comparator. For the current revision level of each overlay, refer
to the Hartzell Aluminum Blade Overhaul Manual 133C (61-13-33).
Description:
Clamp to hold the blade retention components onto the blade shank
for installation into the hub. Designed to fit “A” and “E” shank blades, and
“N” shank composite blades in lightweight compact hubs.
APS-162
61-00-65
Page 4-88
Rev. 12 Aug/11
165A
Beta System Puller
Supersedes:
CST-2834, CST-2834-( )
Description:
Puller to compress the beta system on all -3 turbine propellers that uses
various types of adapters to gain access to the propeller mounting bolts for
propeller removal and installation.
The following replacement components are available individually:
Item Number
Part Number
1. . . . . . . . . . . . . CST-2987+8
2. . . . . . . . . . . . . CST-2987+9
3. . . . . . . . . . . . . CST-2987+13
4. . . . . . . . . . . . . CST-2987+7
NOTE:
Description
Finger Adapter
Finger Adapter
Adapter Nut
Threaded Shaft
CST-2987 includes items 1 through 4 listed above.
CST-2987
CST-2987+8
CST-2987+9
CST-2987
CST-2987+8
(4 pieces included)
CST-2987+13
and
CST-2987+7
(4 pieces included)
CST-2987+9
(3 pieces included)
61-00-65
Page 4-89
Rev. 12 Aug/11
165A
Part Number: CST-3000
(TE187)
CST-3000-1 (TE188)
CST-3000-2 (TE189)
CST-3000-3 (TE190)
CST-3000-4 (TE191)
CST-3000-6 (TE193)
CST-3000-7 (TE194)
CST-3000-9 (TE196)
CST-3000-10 (TE341)
CST-3000-11 (TE474)
CST-3000-12 (TE476)
CST-3000-15 (TE478)
Description:
LM10585AN+4
M10877
M10083
B7421
A10460
E11990
E10950
E12902
E13890
7690
E8190
N7605
Kit contains the necessary materials for the initial qualification of a facility to
perform erosion shield replacements. The kit includes 4 erosion shields and
enough adhesive, fiberglass, vacuum bags, and sealant tape to perform four
erosion shield replacements for evaluation.
Part Number: CST-3000-A (TE342)
CST-3000-1A (TE345)
CST-3000-2A (TE346)
CST-3000-3A (TE347)
CST-3000-4A (TE348)
CST-3000-6A (TE349)
CST-3000-7A (TE350)
CST-3000-9A (TE351)
CST-3000-10A (TE352)
CST-3000-11A (TE475)
CST-3000-12A (TE477)
CST-3000-15A (TE479)
LM10585AN+4
M10877
M10083
B7421
A10460
E11990
E10950
E12902
E13890
7690
E8190
N7605
Description:
Kit contains the necessary materials for the additional qualification of a facility
to perform erosion shield replacement of a blade design different than the
initial design for which the facility is qualified. The kit includes 1 erosion shield
and enough adhesive, fiberglass, vacuum bags, and sealant tape to perform
the erosion shield replacement.
61-00-65
Page 4-90
Rev. 12 Aug/11
165A
Portable Spring Compressor
Description:
Spring compressor for feathering spring assembly during assembly or
disassembly of lightweight turbine “E” shank 5 and 6 Way propellers.
Dual Acting Propeller Assembly Table Add-on Package
Description:
An add-on package compatible with CST-2901(-) propeller assembly tables.
Permits the ability to control HD-E6C type propellers. The add-on package
includes a mounting bracket, electric actuator, push button control box,
BST-2912-10 "C" flange spindle adapter, and the hardware to interface with
the propeller. Requires 105-125V AC, 50/60 Hz or 208-245V AC, 50/60 Hz
source. Hole drilling and some assembly required.
CST-3021.AI
61-00-65
Page 4-91
Rev. 15 Dec/13
165A
Description:
Tools required for disassembly and reassembly of HD-E6C-3 propeller and
PCU.
Qty.
Vendor
Hartzell P/N
Vendor P/N
Description
1
1
1
1
1
1
HP
HP
HP
HP
HP
HP
BST-3027 (TE40)
BST-3030 (TE41)
BST-3031 (TE42)
BST-3033 (TE43)
BST-3035 (TE3)
BST-3036 (TE63)
n/a
n/a
n/a
n/a
n/a
n/a
Modified Crowfoot
Modified Crowfoot
Modified Crowfoot
Modified Crowfoot
Adapter
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
2
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
SO
BH
LS
BST-3037 (TE74)
BST-3038 (TE26)
BST-3039 (TE99)
BST-3041 (TE84)
BST-3044 (TE141)
BST-3045 (TE98)
BST-3054 (TE72)
BST-3055 (TE185)
BST-3055-1 (TE186)
BST-3056 (TE70)
BST-3057 (TE71)
BST-10002 (TE117)
BST-10003 (TE136)
BST-10004 (TE251)
BST-10005 (TE157)
BST-10006 (TE58)
BST-10007 (TE159)
(TE176)
9943BLX13 (TE261)
9943EN1901 (TE262)
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
APS351 BLX 13 EN1 901 Aft Control Spring Compressor
Bearing Puller
Rigging Pin
Clamp Wrench
Puller
Deep Well Socket
Beta Light Switch Test Box
Rigging Cover
Adjustable Spanner Wrench, 1/8 Pin
Ball Head Hex. Wrench Set
1
SO
9943FS081 (TE109)
GFS081 Socket, 6 Point, ¹/8 inch, 3/8 Drive
1
SO
9943MU121 (TE166) GTMU121 1
SO
(TE192)
GFC48A 1
SO
(TE202)
GSF161 1
SO
9943FC012 (TE214) GFC012 2
SO
994313309 (TE229)
GFA4A 1
SO
(TE248)
GF10M Universal Socket, 12 Point, 3/8 inch, 1/4 Drive
Crowfoot Wrench, Open End with Side Lock
Hole, 11/2 inch, 3/8 Drive
Deep Well Socket, 12 Point, 1/2 inch, 3/8 Drive
Crowfoot Wrench, Open End, 3/8 in
Socket Driver, 5/32 Hex. Head, 3/8 Drive
Breaker Bar, 3/8 Drive
61-00-65
Page 4-92
Rev. 12 Aug/11
165A
Part Number: CST-3028 (TE78).....Con’t
Qty.
Vendor
Hartzell P/N
Vendor P/N
Description
1
SO
(TE249)
GV01820 Open End Wrench, Std Length, 9/16 - 5/8 in
1
SO
994313308 (TE255)
GFX1
Extension, 2 inches, 3/8 Drive
1
SO
(TE256)
GFC60A Crowfoot Wrench, 17/8 inch, 3/8 Drive
1
DM
(TE265)
M22520/1-01 Beta Light Switch Crimping Tool
1
SO
(TE250)
PFDH180 Socket, 12 Point, 9/16 inch, 3/8 Drive
1
SO
994313307 (TE253)
QJFR275E Adjustable Torque Wrench, 5 to 75 ft-lb,
3
/8 Drive
1
SO
(TE254)
QJR217C Adjustable Torque Wrench, 30 to 200 in-lb,
3
/8 Drive
1
SO
(TE47)
YA484 Tool Box
1
2
1
1
4
1
1
1
1
1
1
1
1
1
1
1
1
1
SO
AP
AP
AP
MC
LE
LE
LE
LE
LE
LE
LE
LE
LE
LE
LE
LE
SO
994313306 (TE305)
(TE258)
(TE252)
(TE259)
791800247 (TE260)
(TE263)
(TE264)
(TE266)
(TE267)
(TE268)
(TE269)
(TE270)
(TE271)
(TE272)
(TE273)
(TE323)
(TE324)
(TE257)
PMF133
170-6 668 1500-P 90303A247 CUTA2810114C CUTA1870104C CUTA1560203A CUTA1560103B CUTA2180203A CUTA2180103B CUTA2810203A CUTA2810103B CUTA3120203A CUTA3120103B CUTA1250203A
CUTA1250103B
ASA204A
0 - 6 inch Dial Calipers
Apex Torqset Bit, 1/4 inch, 11/4 Length
Thickness Gauge, Straight Leaves
Hand Driver, Replaceable-Bit
Nylon Jack Screws
Installation & Extraction Tool for Relief Valve
Installation & Extraction Tool for Oil Nozzle
Miniature Pick Set
61-00-65
Page 4-93
Rev. 12 Aug/11
165A
Part Number: CST-3028-1 (TE79)
Description:
Tools required for line maintenance of HD-E6C-3 propeller and PCU.
Qty.
Vendor
Hartzell P/N
Vendor P/N
Description
1
HP
HP
HP
HP
LS
SO
AST-2877-1 (TE155)
BST-3048 (TE320)
BST-3041 (TE84)
BST-10001 (TE69)
9943EN1901 (TE262)
9943FC012 (TE214)
n/a
n/a
n/a
n/a
EN1901 GFC012 Torque Wrench Adapter
Rigging Pin
Crowfoot Wrench, Open End, 3/8 inch
1
2
1
2
1
Dual Acting
Line Maintenance Tool Kit (Hartzell Supplied Tools Only)
Part Number: CST-3028-2 (TE276)
Description:
Tools required for line maintenance of HD-E6C-3 propeller and PCU.
Qty. Hartzell P/N
Description
Rigging Pin
1
1
2
1
AST-2877-1 (TE155)
BST-3048 (TE320)
BST-3041 (TE84)
BST-10001 (TE69)
61-00-65
Page 4-94
Rev. 12 Aug/11
165A
Adjustable Riser Fixture
Part Number: CT-1075 (TE48)
Description:
Fixture to allow blade angle measurements during assembly. Used in
conjunction with a bench-top protractor.
APS-159-1
Riser Fixture
No. CT-1075
61-00-65
Page 4-95
Rev. 15 Dec/13
165A
Cylinder Cap
Description:
Cap used with the cylinder when installing the spring assembly in compact
aluminum, feathering -2 propellers.
APS-6263
Blade Angle Locating Fixture
Description:
Fixture to check blade-to-blade angular difference before final hub assembly.
CST2969A
61-00-65
Page 4-96
Rev. 12 Aug/11
165A
Sleeve Intallation Tool
Description:
Tool for installation of the reverse adjustment sleeve in lightweight turbine
propellers.
CST3169
Ultrasonic Inspection Calibration Standard
Part Number: CST-3012 (TE277) Supersedes BST-10009.
Description:
Controlled specimen to confirm calibration of ultrasonic test equipment.
CST3012
61-00-65
Page 4-97
Rev. 12 Aug/11
165A
Description:
Calibration standard for 101088 eddy current probe.
CST3015
Bolt Alignment Fixture
Description:
Used to align mounting bolts in an E-7369 hub with oversize mounting bolt
holes.
CST3178
61-00-65
Page 4-98
Rev. 12 Aug/11
165A
Part Number: CST-2901-( ) (TE129)
Description:
Table used to assemble/disassemble propellers. May order complete
propeller assembly table or contact Hartzell for information to fabricate. The
CST-2901 includes the propeller assembly table and the items listed in the
chart below.
Qty
Item
1
1
1
1
1
1
1
1
1
1
1
1
HPI Part No.
Description
CST-2901 (TE129)
Full Size
CST-2901-1 (TE129)
Short
CST-2901-2 (TE129)
Full Size W/ Spindle Base, Anti-Rotation Pin
CST-2901-3 (TE129)
Short W/ Spindle Base, Anti-Rotation Pin
CST-2901-4 (TE129)
Full Size W/ Building Buck Components
CST-2901-5 (TE129)
Short W/ Building Buck Components
1
CST-2901+1
Base, Full Size
2
CST-2901-1+1
Base, Short
Hpi Oval, Hartzell Balde Decal
2
2
2
2
2
2
3
79980-HPI-LO
2
2
2
2
2
2
4
CST-2901+3
1
1
5
BST-2912 (TE125)
(1)
(1)
6
BST-2912-12 (TE127)
Mid Pitch Adapter
(1)
(1)
7
BST-2912-1 (TE124)
Flanged Hub Spindle
(1)
(1)
8
BST-2912-4 (TE4)
Adapter Ring"N" Flange
(1)
(1)
9
BST-2912-9 (TE2)
"A" Flange Adaptor"C" Flange Adaptor
(1)
(1)
10
BST-2912-10 (TE80)
"C" Flange Adaptor
(1)
(1)
11
BST-2912+ (TE125-1)
Spindle Base
(1)
(1)
12
BST-2912-13 (TE327)
-5 Blade Angle Stop
1
1
Hanger
(1)
(1)
13
BST-2912-11 (TE85)
Anti Rotation Pin
(1)
(1)
14
BST-2912-2 (TE122)
#20 Spline Spindle
(1)
(1)
15
BST-2912-3 (TE123)
#30 Spine Spindle
1
1
1
1
1
1
1
1
16
CST-2901-5
Pneumatics
Anti-rotation Pin
Spindle
Base
Propeller
Assembly Table
(Full Size Shown)
61-00-65
Page 4-99
Rev. 12 Aug/11
165A
Blade Bearing Press
Part Number: DST-2934 (TE93)
Description:
Press to install the inboard split bearing races and retaining rings onto single
shoulder blades. The press also installs the needle roller bearings inside Y,
D, and E shank blade bores.
NOTE: Does not include the hydraulic power unit.
Locator Plate
Reference
Ball Size
DST-2934+1
3/8"
DST-2934+2
1/2"
Use with
Bearing Part
Number
C-792-( )
D-7745-( )
A-2202-( )
C-7438-( )
C-7075-( )
C-2882-( )
61-00-65
Page 4-100
Rev. 15 Dec/13
165A
Ground Hydraulic Power Unit (GHPU)
AC, 110 V
DST-3049-1 (TE318) AC, 220 V
DST-3049-2 (TE318)
DC, 28 V
Description:
Used to change blade angle on the HD-E6C-3 propeller.
• BST-3051 (TE493) Chip Detector Fitting Cover
• BST-3050 (TE492) Chip Detector Fitting
NOTE: A return line fitting composed of
DST-3049+69, DST-3049 +70, and DST-3049 +7
is provided inside a toolbox that is bolted to
the GHPU.
Synchrophaser Check Box
Description:
Check box to perform functional check of synchrophaser computer and related
air frame components.
61-00-65
Page 4-101
Rev. 12 Aug/11
165A
Pilot Tube Removal Fixture
Part Number: DT-336 (TE53)
Description:
This part number may be used to order the drawing of the pilot tube
removal fixture for local fabrication. Fixture to hold the hub during pilot tube
removal. Replacement jaws are available. Used with customer procured
APS-197
hydraulic press.
Hydraulic Press
Ram
Tool No.
BST-2876 (TE107)
Jaw DT-336+6 (TE53-1) and DT336+7 (TE53-2)
that grabs the pilot tube. Refer to chart.
Fixture No. DT-336
Hydraulic Press
Bed
Jaw
Pilot Tube OD
DT-336+6 (TE53-1)
1.5xx inch (38xx mm)
DT-336+7 (TE53-2)
1.7xx inch (44xx mm)
Rolling Machine
Part Number: DT-1724-3(TE116)
AC, 110 V, 60 Hz Complete Machine
(includes blade fixtures)
DT-1724-70 (TE116)
AC, 110 V, 60 Hz Machine only (no blade fixtures)
DT-1724-3(F) (TE116) AC, 220 V, 50 Hz Complete Machine
(includes blade fixtures)
DT-1724-70(F) (TE116)AC, 220 V, 50 Hz Machine only (no blade fixtures)
Description:
Machine to cold compression roll single shoulder aluminum blade shanks.
For operating instructions and adapter listing refer to Hartzell Aluminum Blade
Manual 133C (61-13-33).
APS-925
61-00-65
Page 4-102
Rev. 12 Aug/11
165A
Roller Assembly Tool
Description:
Used to position and align A-5654-11 rollers during assembly of A-5654-1
pitch lock unit.
Bolt Alignment Tool
Part Number:DST-10024(1) (TE361)
Description:
Used to align A-5989-( ) mounting bolts in a D-6168 hub with oversize
mounting bolt holes.
DST10024
TPI-DST-10024-1
DST-10024
DST-10024-1
61-00-65
Page 4-103
Rev. 16 Apr/14
165A
Go-No-Go Gauge
Description:
Used to inspect for deflection of drive tab on B-6428 propeller control unit
drive coupling.
APS6144
Part Number
Description
DT-2997-4 (TE391)
Used to pressure check the pitch change rod bushing on the
engine-side of "N" flange hubs. Used with DT-2997-2 (TE390) or
DT-2997-8 (TE394).
DT-2997-5 (TE392)
Used to pressure check the pitch change rod bushing on the
cylinder-side of "N" flange hubs. Used with DT-2997-7 (TE393) or
DT-2997-9 (TE429).
NOTE: These part numbers may be used to order the drawings
to allow for local fabrication.
APS6265
61-00-65
Page 4-104
Rev. 12 Aug/11
165A
Part Number
Description
DT-2997-2 (TE390)
Adapter to check the pitch change rod bushing on the engine-side
of "N" flange aluminum hubs.Used with DT-2997-4 (TE391).
DT-2997-7 (TE393)
Adapter to check the pitch change rod bushing on the cylinder-side
of aluminum hubs with fine attachment threads. Used with
DT-2997-5 (TE392).
DT-2997-8 (TE394)
Adapter to check the pitch change rod bushing on the engine-side
of "A" flange aluminum hubs. Used with DT-2997-4 (TE391).
DT-2997-9 (TE429)
Adapter to check the pitch change rod bushing on the cylinder-side
of aluminum hubs with coarse cylinder attachment threads.
Used with DT-2997-5 (TE392).
NOTE: These part numbers may be used to order the drawings to allow for local fabrication.
APS6264
61-00-65
Page 4-105
Rev. 12 Aug/11
165A
Part Number: DST-3146-( ) (TE382)
Description:
Used to inspect the condition of D-5117-1 counterweight clamp threaded
holes. Also used to inspect the seal of an assembled propeller.
NOTE: When performing the grease seal pressure test, grease seal
pressure test tool TE443 (BT-3838) must be used as adaptor with the
CST-3117 Probe Assembly. BT-3838-1 in the DST-3146-1 Kit
eliminates the need for an adaptor.
Components:
DST-3146 (TE382)
1..... CST-3117 Probe Assembly
2..... BST-3118Flowmeter
3..... BST-3119Regulator
4..... BST-3122Gauge
5..... CST-3135 Calibration Block
DST-3146-1 (TE382-1)
1A....BT-3838-1 Probe
2......BST-3118Flowmeter
3......BST-3119Regulator
4......BST-3122Gauge
APS6266
2
1A
4
1
3
5
61-00-65
Page 4-106
Rev. 12 Aug/11
165A
Masking Fixture
Description:
Used to mask the pilot tube during the plating process.
NOTE:
This part number may be used to order the drawing to
DST-3483
61-00-65
Page 4-107
Rev. 12 Aug/11
165A
Shot Peen Machine Assembly
Part Number: DST-5855(F) (TE446)(WH)
Description:
A machine that reapplies the compressive layer to the "F" pitch change knob
on "Y" shank blades. The machine consists of one (1) DST-5885-1(F) kit and
the drawings needed to allow for local fabrication of the remainder of the
machine.
NOTE: DST-5855 is designed for applications using 120V-60 Hz electricity. DST-5855F is designed for use with 50 Hz electric supply along with a voltage transformer.
DST-5855
61-00-65
Page 4-108
Rev. 12 Aug/11
165A
Shot Peen, "Y" Shank Knob Kit
Part Number: DST-5855-1(F) (TE447)
Description:
Kit consists of one (1) DST-5855+33 Rotation Plate and one (1)
DST-5855+34 Top Plate plus the drawings needed to permit local fabrication
of a DST-5855(F) Shot Peen Machine Assembly.
NOTE: DST-5855-1 is designed for applications using 120V-60 Hz
electricity. DST-5855-1F is designed for use with 50 Hz electric supply.
Rotation Plate
DST-5855+33
DST-5855+33
REV. A
HARTZELL
SER. NO: 064
Top Plate
DST-5855+34
61-00-65
Page 4-109
Rev. 12 Aug/11
165A
Optical Comparator
Part Number: Cust. P/N (TE28)
Description:
Optical comparator, customer supplied, to inspect the blade retention radius
to determine its acceptability for rework or return to service. Refer to Hartzell
Service Manual 133C (61-13-33), Blade Overhaul, for a listing of suppliers
and approved part numbers.
PCU Filter Removal Tool
Part Number:CG40-4 (TE356)
Rod
CG40-7(TE357) Collet
Vendor:
Snap-On Tools Corp. (SO)
Description:
Used to remove PCU filter B-5840 from the D-1199-2 propeller control unit.
APS6125
Rod
CG40-4
Collet
CG40-7
61-00-65
Page 4-110
Rev. 12 Aug/11
165A
Part Number: ED-520 (TE133), ED-530 (TE134)
Vendor:
Magnaflux Corporation (MF)
Description:
Instrument to locate cracks and flaws in non-magnetic material (single
shoulder aluminum blade retention radii). Used in conjunction with the
following:
AST-2857 (TE94)
Probe and Probe Holder for "Y" Shank Blade
Inspection
AST-2979 (TE121)
BST-2847 (TE128)
Probe Support
BT-1313(-)( ) (TE95)
Eddy Current Probe Unit for Blade Balance Hole Inspection
BST-3069 (TE315)
61-00-65
Page 4-111
Rev. 12 Aug/11
165A
Part Number: KHT9000-9 (TE67)
Vendor:
ALATEC Products Corporation (AL)
Description:
Tool to assist in installing the thread insert into the pre-threaded hole and then
aid in driving in the locking tangs.
Superseded by:BST-3047-( ) TE68-( )
APS-147
Bench Top Blade Angle Protractor
Part Number:
Vendors
PE 105 (TE96)
Mausner Equipment Company, Inc. (MS)
799200105 (TE96)
Description:
Protractor to measure the blade angles of an assembled propeller while
installed on the bench. Used in conjunction with the CT-1075 Riser Fixture.
NOTE:
Locally procured and calibrated bubble protractor accurate to within 0.1 degree may be used and is considered equivalent.
APS-159-1
Bench Top Protractor
Riser Fixture
No. CT1075
61-00-65
Page 4-112
Rev. 12 Aug/11
165A
Crowfoot
Part Number:
SC038 (TE33)
SC040 (TE34)
SC042 (TE35)
SC048 (TE36)
SC052 (TE37)
SC056 (TE38)
SC060 (TE39)
Crowfoot 13/16 inch
Crowfoot 11/4 inch
Crowfoot 15/16 inch
Crowfoot 11/2 inch
Crowfoot 15/8 inch
Crowfoot 13/4 inch
Crowfoot 17/8 inch
Vendor:
Snap-On Tools Corporation (SO)
Description:
Used in conjunction with a 1/2 inch square drive torque wrench or breaker
bar for propeller assembly and disassembly.
APS-173
Apex Torqset Bit
Part Number:170-1/4 (TE44)
Vendor:
APEX Products (AP)
Description:
Bit to remove, install and torque self-locking mounting screws.
APS-146
61-00-65
Page 4-113
Rev. 12 Aug/11
165A
Slimsert® Installation and Removal Tool
Vendor: Fairchild Fasteners
Part Number
Hartzell Part Number
Description
SR25W4A (Rosan)
MR25W4A (McKinnon)
225-072722 (Acme)
BST-2930-1 (TE389-1)
(Supersedes TE314)
Used to install Slimsert®-type threaded inserts
into 1/4-20 or 1/4-28 threaded holes
SR43W4A (Rosan)
MR43W4A (McKinnon)
225-072734 (Acme)
BST-2930-2 (TE389-2)
into 7/16-20 threaded holes
SR50W4A (Rosan)
MR50W4A (McKinnon)
225-072738 (Acme) or
225-890051 (Acme)
BST-2930-3 (TE389-3)
(Supersedes TE312)
SR56W4A (Rosan)
MR56W4A (McKinnon)
225-072742 (Acme) or
225-890053 (Acme)
BST-2930-4 (TE389-4)
(Supersedes TE313)
SR19W4A (Rosan)
MR19W4A (McKinnon)
225-072718 (Acme)
BST-2930-5 (TE389-5)
(Supersedes TE353)
into 10-24 or 10-32 threaded holes
SR16W4A (Rosan)
MR16W4A (McKinnon)
225-072714 (Acme)
BST-2930-6 (TE389-6)
(Supersedes TE389)
into 8-32 threaded holes
SR37W4A (Rosan)
MR37W4A (McKinnon)
225-072730 (Acme) or
225-890031 (Acme)
BST-2930-7 (TE389-7)
SR31W4A (Rosan)
MR31W4A (McKinnon)
225-072726 (Acme)
BST-2930-8 (TE389-8)
SR14W4A (Rosan)
MR14W4A (McKinnon)
225-072710 (Acme)
BST-2930-9 (TE389-9)
SR11W4A (Rosan)
MR11W4A (McKinnon)
225-072706 (Acme)
BST-2930-10 (TE389-10)
BST-2930
61-00-65
Page 4-114
Rev. 15 Dec/13
165A
Helicoil Insert Removal Tool
Vendor:
Heli-Coil Division, Emhart Fastening Systems Group (HE)
Description:
Tool to remove a helicoil insert.
TE Number
Vendor P/N
Hartzell P/N
TE111
1227-6 791912276
APS-178
Helicoil Insert Installation Tool, 7552-4
Vendor:
Heli-Coil Division, Emhart Fastening Systems Group (HE)
Description:
Tool to pre-wind the insert to a smaller diameter for installation into the
prethreaded hole.
TE Number
Vendor P/N
Hartzell P/N
TE66
7552-4 791975524
TE66-17552-5 791975525
TE66-27552-7 791975527
APS-144, APS-147
61-00-65
Page 4-115
Rev. 12 Aug/11
165A
Ultrasonic Flaw Detector Kit
Description:
Instrument to locate flaws in non-magnetic material (composite blade shank
area).
Qty. Vendor
Vendor P/N
1
**
See Note below. (TE375)
1
PM
23SC
1
PM
21PR
1
PM
21PP
1
PM
23BAT-12
1
PM
M207-RB (Included in TE374)
1
PM
DLH-2 (Included in TE374)
1
PM
BCB-58-6 1
HP
CST-3012 (TE277)
**NOTE:
Description
Hard-shell Shipping Case
Seiko Printer
Printer Paper
8 Hour Battery Pack
2.25 MHz Transducer
Delay Tip (Line)
Transducer Cable
Ultrasonic Inspection
Supplied per approved units as listed in Hartzell Composite Blade
Manual 135F (61-13-35), Table 201. Not shown.
61-00-65
Page 4-116
Rev. 12 Aug/11
165A
Rollers
Part Number: MR02030 (TE275)
Roller, Steel 1½" x 2"
MR01020 (TE328)
Roller, Smooth 11/8" x 1/8"
MR10900 (TE329)
Roller, Gooseneck 1" x 1/16"
MR05000 (TE330)
Roller, Rubber 2"
MR05020 (TE331)
Roller, Silicon 15/16" x 1¾"
Vendor:
Everhard Products (EP)
Description:
Miscellaneous rollers used for installation of propeller de-ice boots.
MR02030
Composite Blade Repair Blankets
Part Number: HZP161001 (TE302)
E10950 Blade Repair Blanket
HZP161002 (TE304)
Blade Repair Blanket (4" x 12")
Vendor:
BriskHeat Corporation (BR)
Description:
Heat blankets which provide accelerated cure time when making repairs to
composite blades. TE304 Not shown.
APS2086
61-00-65
Page 4-117
Rev. 15 Dec/13
165A
Heat Gun
Part Number: HL1802E (TE303)
Vendor:
Steinel America (SA)
Description:
Heat Gun for heat shrinking tubing around the wire harness of the de-ice boot
for the HD-E6C-3( ) propeller assembly and the tubing for wires used in an
electrically actuated governor.
HL1802E
Temp-Plate® Recorder
Part Number: 240-120F (TE306)
Records temperatures from 120°F to 180°F
240-190F (TE307)
Records temperatures from 190°F to 220°F
Vendor:
Wahl Instruments, Inc. (WI)
Description:
Temperature indicating strips to be used when performing composite blade
repairs with a blade repair blanket (TE302 or TE304). TE307 Not shown.
TEMPPLTE.TIF
61-00-65
Page 4-118
Rev. 15 Dec/13
165A
Tie Strap Gun
Part Number: GS4H (TE332)
Vendor:
All Phase Electric Supply Co. (AE)
Description:
Device for securing tie straps used on de-ice boots for propeller assembly
HD-E6C-3B.
GS4H
Unfeathering Tool
Part Number: 9943HART-001 (TE316)
Vendor:
Clay-Groomer Machine Shop, Inc. (CG) or Hartzell Propeller, Inc. (HP)
Description:
Tool for unfeathering propeller assembly HC-E4A-3(A,I).
APS2082
TE316
61-00-65
Page 4-119
Rev. 15 Dec/13
165A
Temp-Plate® Recorder
Part Number: 240-090F (TE358)
Vendor:
Wahl Instruments, Inc. (WI)
Description:
Temperature indicating strips to be used when performing a de-ice system
static check on the de-ice system used on the HD-E6C-3( ) ( ) propeller.
APS6123
Signal Generator Model 3001
Part Number: 90F2312 (TE359)
Vendor:
BK Precision (BK)
Description:
Provides an output signal to the aircraft Np sensor, allowing the de-ice
system to be checked statically.
APS6124
61-00-65
Page 4-120
Rev. 12 Aug/11
165A
Bransonic Cleaner
Part Number: 000-951-005 Model B3 (TE370)
Vendor:
Branson Ultrasonics Corporation (BN)
Description:
Used to clean B-5840 PCU filter prior to reinstallation in D-1199-2 propeller
control unit.
APS6146
BRANSO
NIC 3
Megohm Meter
Part Number: Customer P/N (TE354) - A megohm meter meeting the following
requirements:
0-20 megohms at 500V DC or equivalent.
Vendor:
Customer Supplied (CS)
Description:
Used to measure the ring-to-ring insulation resistance on the A-5635-1 slip
ring. Not shown.
61-00-65
Page 4-121
Rev. 12 Aug/11
165A
Milliohmmeter
Part Number: Customer P/N (TE355) - A milliohmmeter meeting the following
specfications:
RANGE
RESOLUTION MAXIMUM TEST NON DRY CIRCUIT TEST
CURRENTACCURACY
1 Year, 18°-28°C
±(%rdg+counts)
PULSEDDC
200 mΩ
10 µΩ
Vendor:
Description:
Used to measure the bonding resistance of the HD-E6C-3( )( ) propeller.
Not shown.
100 mA
0.04 + 2
0.04 + 3
Pin Extractor
Part Number: MS27495R20 (TE369)
Vendor:
Description:
Used to disassemble B-5927 electrical connector on D-1199-2 propeller
control unit and used for removal of pins on electrical connector for
electrically actuated governors
APS6142
61-00-65
Page 4-122
Rev. 16 Apr/14
165A
Slide Hammer
Part Number: CG250-9 and CG250-8A (TE365)
CG41-11 (TE366)
CG41-14 (TE367)
CG41-13 (TE368)
Slide Hammer, 2 lb.
Rod
Collet, 1/4 inch to 5/16 inch
Collet, 3/8 inch to 7/16 inch
(Not shown)
Vendor:
Snap-On Tools Corp. (SO)
Description:
TE365 used in conjunction with TE366, and TE367 or TE368 to remove
bearings B-6133-1 or B-6133-2 from D-1199-2 propeller control unit.
APS6126
TE365
APS6127
TE366
APS6128
TE367
61-00-65
Page 4-123
Rev. 12 Aug/11
165A
Transducer Assembly
Part Number: Cust. P/N (TE374)
Vendor:
Panametrics, Inc.(PM)
Description:
Used in conjunction with Ultrasonic Flaw Detector (TE375) to locate flaws in
non-magnetic material (composite blade shank area). Not shown.
Qty.
Vendor
1
1
PM
PM
Vendor P/N
Description
M207-RB
DLH-2
2.25 MHz Transducer
Delay Line
Part Number: ** See Note below. (TE375)
Description:
Instrument to locate flaws in non-magnetic material (composite blade shank
area). Not shown.
** NOTE:
Supplied per approved units as listed in Hartzell Composite Blade Manual
135F (61-13-35), Table 201. Contact Hartzell Product Support department for
written approval of similar equipment.
61-00-65
Page 4-124
Rev. 12 Aug/11
165A
Vendor:
Van Keuren (VK)
Part Number
Description
0.0525 inch dia. (TE395) Used to inspect the governor control shaft.
0.0620 inch dia. (TE396) Used to inspect the governor rack.
0.0850 inch dia. (TE397) Used to inspect the governor drive shaft gear internal pitch
diameter.
0.2634 inch dia. (TE398) Used to inspect the governor idler gear.
0.2700 inch dia. (TE399) Used to inspect the governor drive shaft gear.
0.0962 inch dia. (TE400) Used to inspect the governor idler gear pitch diameter.
0.1400 inch dia. (TE401) Used to inspect the governor idler gear pitch diameter.
0.1480 inch dia. (TE402) Used to inspect the governor drive shaft gear pitch diameter.
61-00-65
Page 4-125
Rev. 15 Dec/13
165A
Shot Peen Gun
Vendor:
Clemco Industries Corp. (CL)
Description:
Tool used to shot peen blade balance holes. Used with BT-1271-1,2 (TE137),
(not included), CT-1311 (TE12), and BT-1271(-4, -5, -6, -7,-8) (TE494-4, -5,
-6, -7,-8)
Supersedes:
HZP-09S#4 (GO)
BT-1271-1_2
Shot Peen Tube Assembly (TE137) (not included)
Shot Nozzle Unit (TE494-( )
(not included)
Shot Peen Gun
(TE379)
61-00-65
Page 4-126
Rev. 12 Aug/11
165A
No Go Gauge
Part Number: .2760 Pin Gauge, Minus "Y" Tolerance (TE430)
Vendor:
Hemco Corporation (HM)
Description:
Used to inspect the C-6066-1 preload plate.
W10418
Eddy Current Probe
Part Number:
101088 (TE434) (HP)
Description:
Eddy current probe for bearing cavity inspection.
Supersedes:
379-006-430 (TE434) (HK)
W10460
61-00-65
Page 4-127
Rev. 12 Aug/11
165A
"E" Shank Form Tool
Part Number
Description
101679 (TE449)Used to cut the retention radius of the E10950 composite blade
after potting
105473 (TE449-1)
Description:
Used to cut E13890 and E9193 composite blades after potting.
Used with TE450 and TE451.
101679
"E" Shank Potting Mold
Description:
Used when filling the area of the blade retention radius of the E10950
composite blade to provide sufficient material for cutting a new radius.
Used with TE449, TE451, and a customer supplied worm gear hose clamp.
101736
61-00-65
Page 4-128
Rev. 15 Dec/13
165A
Composite E-shank Comparison Chart
Part Number: GT-3669 (TE451)
Description:
Chart to check condition and repairability of composite blade retention
radius. Used in conjunction with a customer supplied optical comparator,
TE449, and TE450.
NOTE: This is a 14-inch diameter chart.
GT-3669
Tube Puller Assembly
Part Number: 101999 (TE452) (CS)
Description:
Tool used to pull the balance tube for the N-shank composite blade. This
part number may be used to order the drawing of the tube puller assembly
for local fabrication. Used with customer supplied press.
101999
61-00-65
Page 4-129
Rev. 12 Aug/11
165A
Balance Adapter
Part Number: 101923 (TE453)(CS)
Description:
Adapter used with the balance arbor for the N-shank composite blade.
This part number may be used to order the drawing of the balance
adapter for local fabrication. Used with customer supplied blade balancing
equipment.
101923
Plug Puller
Description:
Tool used to pull the blade plug for the N-shank composite blade. Used with
a customer supplied press.
101781
61-00-65
Page 4-130
Rev. 12 Aug/11
165A
Blade Spud Adapter
Description:
Adapter used with the blade spud for the N-shank composite blade.
This part number may be used to order the drawing of the balance adapter
for local fabrication. Used with a customer supplied blade spud inspection
bench.
101932
Mandrel
Description:
Adapter used with the N-shank composite blade. This part number may
be used to order the drawing of the mandrel for local fabrication.
103570
61-00-65
Page 4-131
Rev. 12 Aug/11
165A
Description:
Installation of the hub clamping bolts and nuts in 3-bladed compact
propellers with smooth forged hubs. Used with standard 3/8 inch square
drive torque wrench. This part number may be used to order the drawing of
the torque wrench adapter for local fabrication.
101939
Shot Peen Plug
Description:
Plug to mask the blade bore before shot peening on "P" shank, "R" shank,
"W" shank, and "Z" shank blades with "N" modification.
101060
61-00-65
Page 4-132
Rev. 12 Aug/11
165A
Ring
Description:
Adapter used with DST-2934 blade bearing press blade to locate and
install the retention ring and press the bearings during epoxy bonding for
the 103425 composite blade shank. This part number may be used to order
the drawing of the ring for local fabrication.
103572
212-8 Driver
Description:
Bit to remove, install and torque self-locking screws.
61-00-65
Page 4-133
Rev. 12 Aug/11
165A
Torque Wrench
Description:
Used for blade preload of the hovercraft model 103000 assembly. Used
with standard 3/8 inch square drive torque wrench This part number may be
used to order the drawing of the torque wrench for local fabrication.
104287
Stand Adapter
Vendor:
Mahr Federal Inc. (MH), part number 2247086
Description:
Used with customer procured height stand and drive housing
adapter TE497. Customer procured.
104371 (TE496)
61-00-65
Page 4-134
Rev. 17 Dec/14
165A
Drive Housing Adapter
Vendor:
Description:
Used with customer procured height stand and stand adapter TE496.
Customer procured.
104372 (TE497)
Roughness Standard
Vendor:
Description:
Used to measure surface finish. Customer procured.
Part Number
104374 (TE498)
61-00-65
Page 4-135
Rev. 17 Dec/14
165A
Crimp Tool
Part Number: M22520/37-01 (TE499)
Vendor:
Description:
Used to crimp wire splices on the electronic governor. Locally procured.
TI-165008
Description:
Test specimen to calibrate an eddy current instrument before its use when
inspecting the retention radius of X and V shank blades.
BST-3076
61-00-65
Page 4-136
Rev. 13 Jul/12
165A
Eddy Current Probe
Part Number:BST-3077-1 (TE501)
Description:
Standard 0.125 inch diameter pencil probe that has a 200 KHZ frequency.
Locally procured.
3077-1
Fitting Wrench
Description:
Used for fittings of anti-ice assemblies. This part number may be used to
order the drawing of the wrench for local fabrication.
104933
61-00-65
Page 4-137
Rev. 14 Jun/13
165A
Spacer Blank
Description:
Used to make custom sized spacer in accordance with the procedure in
Hartzell Propeller Inc. Blade Shank Rolling Machine Maintenance
Manual 128 (61-00-28).
61-00-65
Page 4-138
Rev. 14 Jun/13
165A
Bearing Assembly Tool
Description:
Used to assemble the bearing on Bantam blades. This part number may be
used to order the drawing of the bearing assembly tool for local fabrication.
105189
Clamp
Description:
Used to assemble the bearing on Bantam blades. This part number may be
used to order the drawing of the clamp for local fabrication.
105190
61-00-65
Page 4-139
Rev. 14 Jun/13
165A
Leak Check Manifold
Description:
Used to perform an assembly leak check before installing the red dye oil in
the propeller hub.
104507
Valve Assembly,
B-1938
Tee, 104508
Reducer, 104509
Air Pressure
Gage,
102560-1
Adapter
Description:
the propeller hub. Used with 104507 (TE506).
104504
61-00-65
Page 4-140
Rev. 14 Jun/13
165A
Check Cylinder
Description:
the propeller hub for Bantam 5-bladed series propellers. Used with 104507
(TE506) and 104504 (TE507).
104798A
Check Cylinder
Description:
Used to perform an assembly leak check before installing the red dye oil
in the propeller hub for 6-bladed Hovercraft propellers. Used with 104507
(TE506) and 104504 (TE507).
105167
61-00-65
Page 4-141
Rev. 14 Jun/13
165A
Plug Assembly
Description:
the propeller hub for Bantam series propellers.
104506
Plug, 104490
O-Ring, C-3317-006
61-00-65
Page 4-142
Rev. 14 Jun/13
165A
Double Shoulder Blade Eddy Current Kit
Description:
Instruments used to perform eddy current inspection of the double shoulder
blade retention radius.
Qty.
1
1
1
1
1
Vendor P/N
Description
BST-3069 (TE315)
BST-3076 (TE500)
BST-3077-1 (TE501)
BST-3078
BST-3075+1
Probe Holder
Eddy Current Probe
Teflon Tape
Protective Case
3075
BST-3076 (TE500)
Probe Holder
BST-3069 (TE315)
Eddy Current Probe
BST-3077-1 (TE501)
61-00-65
Page 4-143
Rev. 14 Jun/13
165A
Torque Unit Adapter
Description:
Wrench to tighten and torque mounting bolts on 3-bladed reversing Bantam
propellers. Used in conjunction with a standard 1/2 inch drive torque wrench.
NOTE:
torque wrench adapter to permit local fabrication.
105266
Torque Unit Adapter
Description:
Wrench to tighten and torque mounting bolts on 3-bladed reversing Bantam
propellers. Used in conjunction with a standard 1/2 inch drive torque wrench.
NOTE:
torque wrench adapter to permit local fabrication.
105269
61-00-65
Page 4-144
Rev. 15 Dec/13
165A
Description:
Adapter permits mounting of 5-bladed Hovercraft propellers to the
CST-2901( ) Propeller Assembly Table. Must be used with the
BST-2912-1 Flanged Spindle.
BST-2912-20
Description:
Adapter permits mounting of 6-bladed Hovercraft propellers to the
CST-2901( ) Propeller Assembly Table. Must be used with the
BST-2912-1 Flanged Spindle.
BST-2912-21
61-00-65
Page 4-145
Rev. 15 Dec/13
165A
Balance Adapter
Description:
Adapter used with the balance arbor for the Bantam composite blade.
This part number may be used to order the drawing of the balance adapter
for local fabrication. Used with the customer supplied blade balancing
equipment.
105274.ai
Bantam Blade Spud Adapter
Part Number: ** See Note below. (TE532)
Description:
Adapter used with the blade spud for the Bantam composite blade.
Not shown.
** NOTE:
Contact Hartzell Propeller Inc. Product Support department for recommended
tooling.
61-00-65
Page 4-146
Rev. 15 Dec/13
165A
Leak Detector Kit
Description:
Leak Detector Kit is an assembly of a digital pressure gauge, fill valve,
fittings, tubing, and a hub connector. Kit is used to inspect the propeller seals
with compressed air prior to filling the hub with red dyed oil in accordance
with HC-SL-61-273.
Air Pressure Gauge
102560-1
102560
Valve Assembly
B-1938
Blade Seal Probe
BT-3838-1
Tubing
102560-3
O-Ring
C-3317-010-2
PSI
97.65
Barbed Fitting
102560-2
Tee Fitting
102560-4
Description:
Adapter used with the NC8834( ) composite blade.
Altered Bushing Liner
105478-5
r
105478
Altered
Bushing Liner
105478-2
Frame Unit
105478-1
Knob
105478-6
Set
Screw
Hold Down
105478-3
Screw
Spacer
105478-4
61-00-65
Page 4-147
Rev. 15 Dec/13
165A
Drill Jig
Description:
Drill jig used to repair the dowel pin in the existing N7605(B,K)( ) and
N7893( ) composite blades in accordance with HC-SB-61-319.
104052
104052-1
Base
104052-2
Knob Locator
Hub Flange Spindle
Description:
Adapter permits mounting of the H, T, Q, and G Hub Flange propellers
to the CST-2901( ) Propeller Assembly Table. Used with TE548 Bantam
Spring Compressor.
BST-2912-19A
Anti-rotate Pin (included)
61-00-65
Page 4-148
Rev. 16 Apr/14
165A
Shank Spacer Puller
Description:
Tool for engaging the threaded bearing spacer in V, V/N, and MV blades to
pull out the spacer and the outboard bearing.
102515
Shank Spacer Puller
Description:
Tool for engaging the threaded bearing spacer in P, R, P/N, M, T, Z/W, W,
M/N, and T/N blades to pull out the spacer and the outboard bearing.
102516
61-00-65
Page 4-149
Rev. 15 Dec/13
165A
Description:
Adapter used with the N7605, N7893, and N9208 composite blade. This
part number may be used to order the drawing of the adapter for local
fabrication.
105501
Preload Stud Plate
Description:
Used for the 103437 hub at overhaul to re-install the mounting studs
properly. Drawing available for local fabrication, not for sale.
103454
61-00-65
Page 4-150
Rev. 15 Dec/13
165A
Valve Assembly Check Tool
Description:
Tool to pressure test the internal relief valve contained in the relief valve
bolt unit in accordance with HC-SB-61-350. This part number may be used
to order the drawing of the valve assembly check tool for local fabrication.
TPI-MB-0022
Cap
Hole
Rubber Washer
O-ring
Relief Valve Bolt Unit
Housing
Inlet Port for Regulated,
Filtered Air
61-00-65
Page 4-151
Rev. 16 Apr/14
165A
Bantam Spring Compressor
Description:
Adapter permits mounting of Bantam propellers to the
CST-2901( ) Propeller Assembly Table. Used with TE536 BST-2912-19 Hub
Flange Spindle.
NOTE: This part number may be used to order the drawing of the
Bantam Spring Compressor to permit local fabrication.
Components: 1
105663 (TE548-1) Extension
2
105664 (TE548-2) Pull Rod
3
105665 (TE548-3) Compression Spring
TPI-165010
2
1
3
61-00-65
Page 4-152
Rev. 16 Apr/14
165A
"F" Flange Bantam Adapter Ring
Description:
Adapter permits mating to the BST-2912-19 spindle so that the Bantam
spring compressor features will work. Used with TE536 BST-2912-19 Hub
Flange Spindle.
NOTE: This part number may be used to order the drawing of the
"F" Flange Bantam Adapter Ring to permit local fabrication.
TPI-BST-2912-22
Right Angle Grease Coupler
Description:
Fits used between the counterweight and the lubrication fitting of the TBM
Socata 5-way Propeller, HC-E5N-3C. Provides 90 degree access.
Vendor
Vendor Part Number
MC
1091K61
OT
2322
TM
THX-418MD0213-4
AF
8034
SP
QCC-HTR
MA
GGA21600
SM
06135
LI
5883
61-00-65
Page 4-153
Rev. 17 Dec/14
165A
61-00-65
Page 4-154
Rev. 17 Dec/14

Tool and Equipment

Transcription

Similar documents

District of Columbia - Governmentattic.org

Amphenol TV-CTV Tri-Start MIL-DTL-38999 Series III - PEI

maxum xtr catalog