Tapcon Sammy Screw

Transcription

Tapcon Sammy Screw

DESCRIPTION/SUGGESTED SPECIFICATIONS
Anchors
for Concrete
Installs into
concrete structures
easily and quickly!
Available
in Vertical,
and Horizontal
Tapcon Sammy Screw—
The Concrete Sammy is made using 5/16” Tapcon® Concrete Screws, perfect for Hanging Sprinklers, Pipes,
Electrical Fixture or HVAC Equipment to cast in place concrete, precast concrete, and open web joist. The
Steel Sammy is available in vertical mount and horizontal mount to accommodate all fastening situations.
ADVANTAGES
Sammy’s for Concrete Product Features
!"Easy two step process
(Drill hole & drive Sammy
concrete anchor).
!"1/4" pre-drilled pilot hole
required.
!"Concrete Installation Tool
available for a one tool
installation process.
Concrete/Wood Installation Kit
The only tool needed to install SAMMYS & SIDEWINDERS
VERTICAL MOUNT
(a)
*Only sold separately - not included in kit.
Part Number
Description
8122910
Concrete Installation Kit (a)
Kit includes the following items:
8113910
#14 Black Nut Driver (b)
8114910
#14 SW Red Nut Driver (c)
8116910
#250 Bit (1/4") (d)
8117910
SDS Bit (1/4") (e)
8118910
7/32 Wood Bit (f)
8120910
HEX 250 Bit Receiver (1/4") (g)
8098910
SL 250 Sleeve (h)
8121910
SDS B250 Bit Receiver (1/4”)*
Each Qty
1
1
1
1
1
1
1
1
ROTARY HAMMER DRILL INTO CONCRETE
SIDEWINDERS®
FOR CONCRETE
HORIZONTAL
MOUNT
(g)
(d)
(b)
(h)
or
(c)
HAMMER DRILL INTO CONCRETE
(b)
(e)
(h)
or
(c)
Construction Products
Call our toll free number 800-387-9692 or visit www.itwconstruction.ca for general information.
Visit ITW Buildex’s SAMMYS web site www.sammysuperscrew.com for the most current product and technical information.
S 17
SAMMYS for Concrete
APPROVALS
APPLICATIONS
Sprinkler Systems
See Selection Chart for items with approvals.
Pipes/Plumbing
Electrical Lighting and Fixtures
HVAC Equipment and Fixutres
INSTALLATION INSTRUCTIONS
VERTICAL MOUNT
1. Using an SDS 250 carbide tip bit or a HEX RECEIVER with a #250 carbide
tip bit, pre-drill the concrete member to a depth of 2" with an electric
impact/drill set on impact mode.
2. After pre-drilling has been completed, install the SLEEVE TOOL over the
bit (the bit should remain in the drill), and insert the #14 (black) nut
driver (p/n 8113910) into the opposite end.
3. Insert the concrete screw into the nut driver.
4. Place tip of screw into the pre-drilled hole, turn impact/drill unit to drill
mode and begin insertion. When the nut driver spins free on the screw,
installation is complete. Stop and remove drill.
5. The concrete screw is ready to receive 1/4", 3/8", 1/2", or metric all
thread rod or bolt stock. (#14SW red nut driver used with 1/2" screw)
NOTE: Use a 1200 maximum RPM drill for installation.
Sammy’s Swivel® Product Features
!"Installes vertically and
swivels up to 89° in wood
& concrete structures.
NOTE: Do not install concrete screws while the drill unit is in impact mode
— doing so will destroy the pullout factor of the screw.
INSTALLATION INSTRUCTIONS
HORIZONTAL MOUNT
!"Eliminates distortion of
threaded rod.
!"1/4" pre-drilled pilot hole
required.
1. Using an SDS 250 carbide tip bit or a HEX RECEIVER with a #250
!"Concrete Installation Tool
available for a one tool
installation process.
2. After pre-drilling has been completed, install the SLEEVE TOOL over the
carbide tip bit, predrill the concrete member to a depth of 2" with
an impact/drill set on impact mode.
bit (the bit should remain in the drill), and insert the #14SW (red) nut
driver (p/n 8114910) into the opposite end.
3. Install the SWC screw into the nut driver.
4. Place tip of screw into the pre-drilled hole, turn impact/drill unit to
drill mode and begin insertion. When the nut driver spins free on the
SWC screw, installation is complete. Stop and remove drill.
5. The SWC screw is ready to receive 1/4", 3/8" or metric all thread rod or
bolt stock.
NOTE: Use a 1200 maximum RPM drill for installation.
NOTE: Do not install concrete screws while the drill unit is in impact mode
— doing so will destroy the pullout factor of the fastener.
S 18
SAMMYS for Concrete
SELECTION CHART
SAMMYS Vertical Mount
ROD
SIZE
PART
NUMBER
1/4"
!"
Part # 8113910
DESCRIPTION
8058957
CST 200
5/16 x 1-3/4"
2400
3/8"
8059957
CST 20
5/16 x 1-3/4"
2400
1/2"
8060925
CST 2
5/16 x 1-3/4"
2400
SAMMYS Swivel Head®
ROD
SIZE
3/8"
1/2"
PART
NUMBER
8269957
8303957
MODEL
TEST
LOAD
(LBS)
ULTIMATE
PULLOUT (LBS)
MODEL
!"
Part # 8114910
1475
!"
Part # 8273910
BOX
QTY
CASE
QTY
25
125
25
125
25
125
Part #
8114910
NUT
DRIVER
DESCRIPTION
ULTIMATE
PULLOUT (LBS)
BOX
QTY
CASE
QTY
5/16 x 1-3/4"
2537 in 3000 psi concrete
1459 @45° off vertical in 3000 psi concrete
1636 @ 45° off vertical in 6000 psi concrete
25
125
5/16 x 1-3/4"
1459 @45° off vertical in 3000 psi concrete
1636 @ 45° off vertical in 6000 psi concrete
25
SH-GST/CST 20
SH-GST/CST 2.0
PART
NUMBER
1/4"
8062957
SWC 200
5/16 x 1-3/4"
2450
3/8"
8061957
SWC 20
5/16 x 1-3/4"
2450
MODEL
DESCRIPTION
Part #
8113910
Part #
8273910
SAMMYS Sidewinders
for Horizontal Mount
ROD
SIZE
NUT
DRIVE
TEST
LOAD
(LBS)
ULTIMATE PULLOUT
(LBS)
1475
125
BOX
QTY
CASE
QTY
NUT
DRIVE
25
125
25
125
Part #
8114910
S 19
SAMMYS for Concrete – Seismic Restraint
DESCRIPTION
SWC 20 FOR 3/8” ROD
Structural attachment for installation of branch/end of line restraint using 3/8"
threaded rod. The SWC 20 is designed for use in concrete structures such as poured
concrete, T- or L-beams with compressive strength of 3000-5000 psi. This fastening
system provides a secure and economical attachment to the structure.
SPECIFICATIONS
Restrained Pipe Size:
Up to Schedule 40 pipe 2” or less
Max Length of
Restraint Material:
See Maximum Horizontal Load Tables below.
Maximum Angle:
45° from horizontal
Material:
Carbon Steel
Screw Description:
5/16”-14 x 1-3/4” Hi-Lo Tacpcon®
Finish:
Electro-Zinc (cap) and Blue Climaseal® (screw)
Testing:
BX Report # R-1362
Listing:
FM Report # 3031269
UL 203A pending
SELECTION CHART
SAMMYS Sidewinders
for Concrete - Seismic Restraint
ROD
SIZE
PART
NUMBER
3/8"
8061957
MIN
THICKNESS
MODEL
SWC 20
N/A
MAX
THICKNESS
N/A
APPLICATION
BOX
QTY
CASE
QTY
3000 PSI Poured Concrete or CMU
25
125
NUT
DRIVE
PERFORMANCE TABLES
Maximum Horizontal Loads for
Restraint with l/r=100, 200, 300, and 400
Restraint Shape and Size
Rods (all thread)
Rods (threaded at ends only)
Reference: NFPA 13, (2007)
S 20
Nominal Diameter
Area (in.2)
Least Radius of
Gyration, r (in.)
3/8 in.
1/2 in.
3/8 in.
1/2 in.
0.07
0.129
0.11
0.196
0.075
0.101
0.094
0.125
l/r = 100
0.6
0.8
0.8
1.0
Maximum Rod Length for l/r (ft)
l/r = 200
l/r = 300
l/r = 400*
1.3
1.9
2.5
1.7
2.5
3.4
1.6
2.4
3.1
2.1
3.1
4.2
* Reference: NFPA 13, (2010)

Tapcon Sammy Screw

Transcription

Similar documents

Trubolt +