AVI-ON-1012 AVI-ON-MESH-DEV

Modules
Development Board
AVI-ON-1012
AVI-ON-MESH-DEV
The AVI-ON-1012 is an RF module built on the CSR1012 chipset, which
provides a single-chip solution to controlling all types of lighting and other
devices, whether line-connected or battery-powered.
Controlling host and radio interfaces, the on-chip microcontroller runs both the Bluetooth Stack and the Avi-on
Bluetooth Mesh Application Stack. The on-chip RF
transceiver includes the complete receiver and transmitter
functions and integrated antenna or external antenna
options.
A complete IOT Integration Environment
!
AVI-ON-1012 Module (18×12×2.3 mm with onboard
antenna, shown at right)
!
Avi-on-MESH-DEV (development kit for lighting and
power controls, photo on later page)
AVI-ON-1012
Powered by Avi-on™ Platform & Firmware
Modules ship pre-loaded with Powered by Avi-on™ firmware suitable for prototype builds and
testing of lighting and control devices and is fully integrated with the Avi-on iOS and Android
mobile applications available for free download. The complete app-cloud-firmware-modulesupport package enables manufacturers to design and ship products in less than six months.
Firmware customization for multiple PWM, I2C,
UART, SPI, TRIAC, ADC and other dimming
protocols is available by special arrangement.
Copyright © Avi-on Labs, Inc. 2015. All rights reserved.
!
Page 1 of 9
Avi-on.com
More information at Avi-on.com
Contact [email protected]
Avi-on Module Features
!
One step integration using Powered by Avi-on™ platform of app-cloud-firmware-support.
Includes plug-and-play interoperability with the Powered by Avi-on™ product ecosystem
!
Built in UART, I2C, SPI, ADC, and multiple PWM dimming interfaces
!
Up to +85C operating temp
!
External EEPROM memory provides storage for the Bluetooth software parameter and
application parameter
!
Electrical:
o DC Supply: 1.8V ~3.6V
o Low current consumption: 24 mA @3V (Peak Current)
!
High performance integrated antenna (on Avi-on-1012-ONB). Contact Avi-on for AVI-ON1012-EXT (External Antenna) Mechanicals
Detailed Specifications
Item
2.4.1
Characteristics
RF Technology
2.4.2
RF Frequency
2.4.3
2.4.4
2.4.5
2.4.6
2.4.7
2.4.8
2.4.9
2.4.10
Modulation
Schemes
Operating
Frequency
Channel
Numbers
Data Rate
Transmitter
Output Power
Receiver
Sensitivity
Antenna Type
Operating
Voltage
2.4.11
Current
Consumption
2.4.12
2.4.13
Size
Operating Temp
Detailed Description
" Frequency Hopping Spread Spectrum
" 2400 to 2483.5 MHz USA/EUROPE/JAPAN
" 2446.5 to 2483.5 MHz France
" 0.5 BT , GFSK
" Index : 0.28 – 0.35.
"
2400 ~ 2483.5 MHz ISM band
"
40 (f= 2402 + k*2 MHz ,k =0, 1,2 ..,39)
"
1 Mbps (Typically)
"
9 dBm
"
-93 dBm Typical
"
Integrated PCB antenna
"
1.8V ~3.6VDC
"
"
"
"
"
18 [email protected] active mode
35 [email protected] active Mode
Max. <5uA@3V Sleep mode (estimated)
18mm ×12mm × 2.3mm (L x W x H)
-30° C to +85° C
Copyright © Avi-on Labs, Inc. 2015. All rights reserved.
Page 2 of 9
Avi-on.com
More information at Avi-on.com
Contact [email protected]
Regulatory Certifications
!
Item
Feature
5.1
USA
5.2
European
5.3
Canada
5.4
Japan
5.5
BQB
Detailed Description
"
"
"
"
"
"
"
"
"
FCC part 15.247, 15.209, 15B, Certificate
Pending
EN 300 328
EN 301489-1/17
EN 60950-1
ETSI
ICES003
RSS210
ARIB STD-T66 and RCR STD-33A, and
certified by MPT
Bluetooth Certification Pending
!
Default Pin Assignments
Pins Name
J1 WAKE
J2
J3
J4
J5
J6
J7
J8
J9
J10
J11
J12
J13
Function
I
Description
Not Used Tied to GND
32.768KHz installed, Do not connect to
XTAL_32K_IN
Analog in
this Pin.
32.768KHz installed, Do not connect to
XTAL_32K_OUT Analog In
this Pin.
SPI serial flash installed, or I2C clock
I2C_SCL
I/O
Input / output.
VBATT
Power
Power input.
SPI serial flash installed, or I2C data Input
I2C_SDA
I/O
/ output.
Selects SPI debug or Programmable I/O,
Pull-High : SPI debug
SPI_PION
I
Pull-down: Programmable I/O line, default
is.
PIO[11]
I/O
Programmable I/O
PIO[10]
I/O
Programmable I/O
PIO[9]
I/O
Programmable I/O
SPI_MISO
O
SPI data output or Programmable I/O
SPI_MOSI
I
SPI data input or Programmable I/O
SPI_CSB
I
SPI select or Programmable I/O
Copyright © Avi-on Labs, Inc. 2015. All rights reserved.
Page 3 of 9
Avi-on.com
More information at Avi-on.com
Contact [email protected]
J14
J15
J16
J17
J18
J19
J20
J21
J22
J23
J24
J25
J26
SPI_CLK
PIO[4]
VDD_PADS
PIO[3]
UART0_RX
UART0_TX
AIO[0]
AIO[1]
AIO[2]
GND
GND
GND
GND
I/O
I/O
Power
I/O
I
O
I/O
I/O
I/O
Ground
Ground
Ground
Ground
SPI clock or Programmable I/O
Programmable I/O
Positive supply for all digital I/O ports
Programmable I/O
UART RX or Programmable I/O
UART TX or Programmable I/O
Analogue Programmable I/O
Analogue Programmable I/O
Analogue Programmable I/O
Ground
Ground
Ground
Ground
Standard Functionality with Avi-on Mesh Dev Kit Firmware
Minimum connection requirements:
Pins
Name
J1
WAKE
J5
J16
J23
J24
J25
J26
VBATT
VDD_PADS
GND
GND
GND
GND
Function
Description
Connect to VBATT for line powered and
Wake/Sleep device control applications.
Use as
WAKE line for battery/sensor applications
Power
Power input.
Power
Positive supply for all digital I/O ports
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Recommended connections:
Pins
Name
J9 PIO[10]
J10 PIO[9]
J15 PIO[4]
Function
Description
I/O
PWM Output
I/O
Toggle Switch Input
I/O
Indicator Output
PIO[10] PWM Output
Configured as a PWM Output; the PWM has a Frequency of 975Hz. The Duty
Cycle of the PWM can be varied from 0% (0V) to 100% (VDD_PADS) in 255
steps.
!
Copyright © Avi-on Labs, Inc. 2015. All rights reserved.
Page 4 of 9
Avi-on.com
More information at Avi-on.com
Contact [email protected]
PIO[9] Toggle Switch Input
Configured as an Input for enabling/disabling & ramping UP/DOWN the output of
the PWM on PIO[10]. By default the pin is pulled up to VDD_PADS and when
intermittently driven to GND the PWM output on PIO[10] will be disabled. If the
line is held at GND then the output of the PWM will Ramp UP to MAX (or ramp
DOWN to 0V the function switches to ramping UP then DOWN alternately). The
pin also acts as a Hard Reset that will unclaim the Module (if previously claimed)
if held at GND for 12 seconds.
PIO[4] Indicator Output
Configured as an Output that indicates the state of the Module it is recommended
that it be connected to an LED. If the Module is unclaimed then the output will
flash twice. If the Module is claimed then the output will indicate the state of the
PWM on PIO[10]. The output will be LOW (GND) when the PWM in ON and
HIGH (VDD_PADS) when the PWM is OFF.
Hardware Block Diagram, AVI-ON-1012
!
!
Copyright © Avi-on Labs, Inc. 2015. All rights reserved.
Page 5 of 9
Avi-on.com
More information at Avi-on.com
Contact [email protected]
Mechanicals AVI-ON-1012
!
Top$View:$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
Bottom$View:$
$
!
!
!
Copyright © Avi-on Labs, Inc. 2015. All rights reserved.
Page 6 of 9
Avi-on.com
More information at Avi-on.com
Contact [email protected]
Pin Assignment AVI-ON-2012-INT
!
!
Copyright © Avi-on Labs, Inc. 2015. All rights reserved.
!
Page 7 of 9
Avi-on.com
More information at Avi-on.com
Contact [email protected]
!
Pad Layout, AVI-ON-1012
Copyright © Avi-on Labs, Inc. 2015. All rights reserved.
Page 8 of 9
Avi-on.com
More information at Avi-on.com
Contact [email protected]
AVI-ON-MESH-DEV: Avi-on Development Board
This full-scale integration and test board is designed to enable manufacturers to quickly
develop lighting and power controls using the Powered by Avi-on™ app-cloud-firmware
platform. The board comes with several Avi-on-1012 Modules loaded with Avi-on’s
standard Dev Kit firmware.
Board specifications and instructions plus other firmware and dimming protocols are
available upon special arrangement.
AVI-ON-1012-DEV
Specifications available upon request
Copyright © Avi-on Labs, Inc. 2015. All rights reserved.
Page 9 of 9
Avi-on.com
Get Powered by Avi-onTM
Jumpstart Your Smart Design
Contact us on Monday, get an Integration Kit
on Tuesday, and show off a working prototype
to your organization by Friday.
Sounds crazy? It’s been done.
Why so fast? Because the iOS and Android
apps are already finished. Security and
account management is complete. Standard
firmware is in the integration kit.
Ship In Less Than Six Months
Need on/off, dimming or speed control? It’s on
the app, right out of the box. Schedules and
timers? Done.
And did we mention instant set-up,
many-to-many controls, and secure network
formation? All are done.
Just connect the kit to your prototype, download the app, and demo your new connected
product. It’s that simple.
Get point-to-point programming distances of
up to 100 feet, and virtually unlimited coverage with the mesh network.
And best of all, you get forward-compatible
support on both the apps and the firmware
with no ongoing maintenance fees.
This information is intended solely for the use of the intended recipient, and contains information that is privileged, confidential or exempt from
disclosure under applicable law. Any dissemination, distribution, or copying of this information is strictly prohibited.
2015 - Avi-on Labs, LLC - All Rights Reserved - Bluetooth, Bluetooth Smart and CSRMesh trademarks are all used in accordance with current
copyright and licensing agreements.
Get Powered by Avi-onTM
Avi-on Gives You a Competitive Edge
The Powered by Avi-on™ platform enables
brands to bring beautiful, interoperable, scalable
and reliable connected products to market in less
than six months. Built on the global standards of
CSRmesh™ and Bluetooth Smart™, Avi-on deliver
s polished mobile apps, device-specific features,
a robust and secure cloud, forward-compatible
support; and it is all in one turnkey package.
Great price point, fast time to market,
forward compatible support. Avi-on modules
and solutions deliver products that cost less than
other radio platforms and they don’t require a
gateway to turn on the first device. With Avi-on’s
turnkey app-cloud-module-support platform, you
innovate now and have support for decades to
come. While simple and easy to use out of the
box, your products can be compatible with
gateway technologies and other control systems
as well.
Avi-on Bluetooth® Smart Mesh Architecture
Secure, scalable and high performance. Avi-on’s technology provides users with wired
performance without wires. In lighting, we deliver real-time dimming across multiple devices from
battery-powered switches. Our platform is scalable to support large installations and millions of
users. It is secure, with unique features that support high-density environments and real world
scenarios.
Interoperable, proven technology. People want their devices to talk to each other. Avi-on is built
on CSRmesh™, the core of the upcoming Bluetooth Smart Mesh standard being endorsed by the
Bluetooth SIG Working Group. Joining Avi-on means that your products will be interoperable with a
large and growing ecosystem of products, starting with GE branded lighting controls and timers
manufactured by Jasco Products.
About Avi-on
The Powered by Avi-on platform offers a turnkey app-cloud-module software solution that enables
manufacturers to get an entire line of products to market in less than six months. Built on Bluetooth
Smart™ and CSRmesh™, Avi-on is cost effective, secure, and requires no central gateway. The
underlying mesh technology specification is part of a global interoperable standard sponsored by
the Bluetooth Special Interest Group.
This information is intended solely for the use of the intended recipient, and contains information that is privileged, confidential or exempt from
disclosure under applicable law. Any dissemination, distribution, or copying of this information is strictly prohibited.
2015 - Avi-on Labs, LLC - All Rights Reserved - Bluetooth, Bluetooth Smart and CSRMesh trademarks are all used in accordance with current
copyright and licensing agreements.