8-3121 - Paw Paw Rentals

Transcription

Parts Catalog 8-3121
R
Ingersoll
COMPACT TRACTORS
WITH ONAN ENGINES
4016 SN 14149628 TO 14170800
3016PS, 3018PS, 3020PS
4016PS, 4018PS 4020PS
INDEX
PAINT
ENGINES
GENERAL INFO
MODEL 3016PS, 3018PS, 3020PS, 4016, 4016PS, 4018PS, 4020PS COMPACT TRACTORS
INDEX
PRODUCT IDENTIFICATION NUMBERS (PIN.)
OR SERIAL NUMBERS (S/N)
TRACTOR MODEL AND P.I.N.
OR SERIAL NUMBERS
NOTE:
ENGINE MODEL, SERIAL AND
SPECIFICATION NUMBERS
In this catalog there are references to serial numbers.
To order the correct part, use these serial numbers as a guide.
ENGINE IDENTIFICATION
TRACTOR MODEL
ENGINE MODEL
3016PS, 4016PS, 4016
C33235
ONAN P216G-I SPEC. NO. 10904C
3018PS, 4018PS
C33236
ONAN P218G-l SPEC. NO. 10904C
* LINAMAR LX770 SPEC. NO. 10905G
SPEC .NO. 11457G
4020PS
* LINAMAR ENGINES USED PIN 17192461 AND AFTER
C33237
ONAN P220G-I SPEC. NO. 10904C
* LINAMAR LX790 SPEC. NO. 10905G
SPEC .NO. 11457G
MAIN
GENERAL INFORMATION
INDEX
INDEX
PARTS ORDERS
There is an index at the front and rear of this
catalog. The front index is an alphabetical index of
the major groups or assemblies.
1.
Correct part number.
2.
Complete description of part or component.
The rear index is a numerical index of the part
numbers and pages on which these numbers are
shown.
3.
Total quantity of each part or component.
4.
Product model number.
ILLUSTRATION
5.
All necessary product identification numbers.
Each illustration in this catalog shows a group of
parts or components. These parts and components
are aligned approximately as the parts and
components on your machine. Each part and
component in an illustration has a reference
number. These reference numbers are in a list on
the page opposite of the illustration. Next to the
reference number is the part number, description
and required quantity of the part shown in the
illustration.
6.
Method for sending the parts.
7.
Complete and correct address.
UAR - “Use as required” indicates that the part
quantity is variable.
NSS - “Not sold separately” indicates that the part is
only available as component of an assembly or the
part must be purchased locally. If the part is an
assembly component, the description will be
indented under the assembly description in the parts
list.
CATALOG REVISIONS
As the product changes, new pages will be available
for your catalog. A notice will be issued.
IMPORTANT: Put all revisions into the catalog as
soon as possible.
RIGHT HAND AND LEFT HAND IDENTIFICATION
The words right hand (RH) and left hand (LH) as
used in this catalog indicate the direction while you
are in the operator’s seat in the normal operating
position.
INDENTED DESCRIPTIONS
O/L - “Obtain locally”
- “Footnotes” are added to a part number
when more information is needed for identification.
They only relate to the part numbers indicated.
All orders must include the following information:
REF.
28
29
30
31
32
33
34
35
36
37
PART
C
C
C
C
C
C
G
16132C
1392-
NO.
55159
56208
55956
55957
56210
56209
45175
836
104
55889
410
4
DESCRIPTION
An assembly can have many components. The
components of an assembly are indicated by an
indented description. The quantity for an indented
part is the total needed for that complete assembly.
See the example.
REQ’D
CYLINDER ASSY - rear steering ...............................................................1
SOCKET ASSY - rear cylinder ..................................................................1
PLUG - adjusting, socket assy ................................................................1
SEAT- socket, ball...................................................................................2
SPRING-socket .......................................................................................1
SEAT - socket spring...............................................................................1
CLAMP ASSY - socket assy .....................................................................1
BOLT-1/2”x2-1/4” N.F. hex......................................................................1
PIN-cotter, 3/16”x3” ...................................................................................1
STUD - ball, socket & cylinder ..................................................................2
BOLT-1/4”x5/8”N.C.,hex ...........................................................................4
LOCK WASHER - 1/4”SAE ........................................................................4
Paint & Oil
INDEX
PAINT
Power Red Gloss
16-ounce Aerosol Can........ C28484
Quart .................................. C28485
Power White
Quart .................................. C28845
Power Yellow
(Older 600 Series)
Quart .................................. C28848
Power Tan
(6000 Series)
Quart .................................. C28854
Desert Sunset
(Older 400 Series)
Quart .................................. C28852
Black, Semi Gloss
Quart .................................. C28850
Black, High Heat
Silver
M & W Plum
16-ounce Aerosol Can........ 10-5688
Grazer Grey
Quart .................................. C38982
Odyssey Charcoal Grey
HYDRAULIC OIL
20W40, Use 32 Degrees and above.
12-Quart Case............. C32778
5W20, Use Below 32 Degrees.
12-Quart Case............. C32777
MAIN
ALPHABETICAL INDEX
ENGINE SECTION
PAGE
Air Cleaner .............................................. 17
Battery..................................................... 59
Breather, Crankcase................................ 17
Camshaft ................................................... 5
Carburetor .......................................... 15-19
Choke Linkage ........................................ 19
Connecting Rod......................................... 5
Crankshaft ................................................. 5
Cylinder Block ........................................ 7-9
Cylinder Head......................................... 7-9
Electrical System ................................ 65-69
Engine Block & Attaching Parts .............. 7-9
Exhaust System....................................... 23
Filter, Breather......................................... 17
Filter, Fuel ............................................... 15
Filter, Oil .................................................. 11
PAGE
Flywheel ......................................................5
Fuel Pump .................................................15
Fuel System...............................................15
Gasket Kits ...............................................7-9
Governor ..............................................13-21
Muffler .......................................................23
Shields..................................................21-23
Oil Pan.......................................................11
Piston ..........................................................5
PTO Clutch................................................25
Rotor, Ignition ............................................13
Spark Plug............................................65-67
Starter........................................................63
Tank, Fuel .................................................15
Throttle Linkage.........................................19
Valves.......................................................7-9
BASIC TRACTOR SECTION
Axle, Front ............................................... 39
Axle, Rear................................................ 43
Baffles & Shrouds ............................... 21-23
Brakes ..................................................... 41
Control, Speed......................................... 59
Decals...................................................... 71
Electrical System ................................ 65-69
Fenders .............................................. 33-35
Frame ................................................. 27-29
Grille ........................................................ 31
Headlights................................................ 69
Hitch, Tow................................................ 59
Hood........................................................ 31
Hydraulics............................................ 45-61
Adapter, Pump Drive...............................55
Hoses, Lines & Fittings ..................... 45-61
Motor, Hydraulic Drive.............................55
Pump ....................................................... 53
Valve, Control .......................................... 57
Linkage, Valve, Control ............................ 59
Hydraulic Lift ............................................ 61
Instruments ............................................. 65-67
Mounts, Engine....................................... 27-29
Mounts, Heat Exchanger......................... 45-49
PTO Clutch (electric).................................... 25
Reflector, rear .............................................. 69
Seat, Operator’s...................................... 33-35
Steering, Power ........................................... 51
Steering Wheel & Gear (manual) . . . .......... 37
Tool Tray................................................. 33-35
Transmission ............................................... 43
Wheels, Front & Rear................................... 41
PISTON CRANKSHAFT, FLYWHEEL, AND CAMSHAFT
INDEX
INDEX
REF.
1
1
1
1
1
1
2
3
4
4
4
4
4
4
5
PART NO.
C40793
C24932
C40794
C40795
C40796
C24936
C29972
C20241
C29739
C24938
C24939
C24940
C24941
C24942
C29750
5
C29751
5
C20204
5
C20205
5
C25383
5
C25384
5
C25385
5
C25386
6
7
8
9
10
11
12
13
C25774
C25775
C20223
C24325
C24326
211-216
126-9
C32468
13
14
15
16
17
17
18
19
20
21
22
23
24
25
26
27
28
29
30
C32469
C22261
C20229
C20233
C32284
C32285
126-9
C20218
C20219
C22262
C31976
C32286
C20226
C32473
C32463
C20303
C32464
C32287
C32288
PISTON, CRANKSHAFT, FLYWHEEL AND CAMSHAFT
DESCRIPTION
REQ’D
PISTON - standard (includes pin and retaining ring)...................................................................... 2
PISTON - .005(0.13 mm) oversize (includes pin and retaining ring) ............................................. 2
PISTON - .010(0.25 mm) oversize (includes pin and retaining ring) .............................................. 2
PIN - piston ................................................................................................................................. 2
RING-retaining ............................................................................................................................ 4
RING SET - piston (standard)........................................................................................................ 2
RING SET - piston .005” (0.13 mm) oversize ................................................................................ 2
CONNECTING ROD - (standard) includes nut and bolt
(3016PS, 4016, 4016PS) ............................................................................................................ 2
CONNECTING ROD - .010” (0.25 mm) undersize, includes nut & bolt
(3016PS, 4016, 4016PS) ............................................................................................................ 2
(3016PS, 4016, 4016PS) ............................................................................................................ 2
CONNECTING ROD - .030” (.076 mm) undersize, includes nut & bolt
(3016PS, 4016, 4016PS) ............................................................................................................ 2
CONNECTING ROD - (standard) includes nut & bolt
(3018PS, 3020PS, 4018PS, 4020PS)......................................................................................... 2
(3018PS, 3020PS, 4018PS, 4020PS)......................................................................................... 2
(3018PS, 3020PS, 4018PS, 4020PS)......................................................................................... 2
(3018PS, 3020PS, 4018PS, 4020PS)......................................................................................... 2
BOLT - connecting rod 5/16” special N.F.................................................................................... 4
NUT - lock, connecting rod 5/16” N.F.......................................................................................... 4
RING - retaining ............................................................................................................................. 1
HUB - governor cup ....................................................................................................................... 1
CUP - governor ............................................................................................................................. 1
BALL - governor............................................................................................................................. 5
KEY - woodruff 1/8” x l/2”............................................................................................................... 1
CAMSHAFT - (includes pin) (3016PS, 3018PS, 4016,
4016PS,4018PS) ........................................................................................................................ 1
CAMSHAFT - (includes pin) (3020PS, 4020PS)............................................................................ 1
GEAR ASSEMBLY - camshaft....................................................................................................... 1
WASHER - thrust ........................................................................................................................... 1
PIN - center.................................................................................................................................... 1
CRANKSHAFT - engine (3016PS, 4016, 4016PS) ........................................................................ 1
CRANKSHAFT - engine (3018PS, 3020PS, 4018PS, 4020PS) .................................................... 1
KEY - woodruff, crankshaft gear ................................................................................................ 1
RING - retaining ............................................................................................................................. 1
WASHER - special......................................................................................................................... 1
GEAR - crankshaft ......................................................................................................................... 1
KEY - square, clutch ...................................................................................................................... 1
FLYWHEEL - engine...................................................................................................................... 1
GEAR - ring, flywheel.................................................................................................................. 1
BOLT - flywheel ............................................................................................................................. 1
WASHER - special......................................................................................................................... 1
WASHER - special......................................................................................................................... 6
SCREW - #10 - 24 x 3/8 flange lock ............................................................................................ 6
SCREEN - flywheel........................................................................................................................ 1
KEY - 3/16” x 2” special, flywheel ................................................................................................ 1
CYLINDER BLOCK
INDEX
INDEX
CYLINDER BLOCK
REF.
PART NO.
DESCRIPTION
1
C33243
1
C33244
2
3
4
5
5
5
5
5
6
7
8
9
10
11
12
13
13
13
13
13
14
14
14
14
15
15
15
15
15
16
16
19
20
24
26
27
27
27
28
29
30
31
32
41-26
113-208
C20256
C22618
C22619
C22620
C22621
C22622
C20267
C20268
C20269
C20270
C20271
C20272
C24946
C29974
C29975
C29976
C29977
C29978
C20287
C20289
C20290
C20291
C20295
C20296
C20297
C20298
C20299
C32274
C32275
192-21
C23320
C20250
C20251
C20276
C20471
C20277
C32272
C32273
113-132
C32276
C32277
BLOCK ASSEMBLY - short (3016PS, 4016, 4016PS) includes
cylinder and crankcase, all bearings, crankshaft, camshaft, timing
gear, connecting rods, pistons, piston rings, valves, oil pump and
breather tube (does not include gasket set) .................................................1
BLOCK ASSEMBLY - short (3018PS, 3020PS, 4018PS, 4020PS)
includes cylinder and crankcase, all bearings, crankshaft, camshaft,
timing gear, connecting rods, pistons, piston rings, valves, oil pump
and breather tube (does not include gasket set) ..........................................1
PLUG - welch ..............................................................................................1
BOLT - 3/8”-16x1-1/4”..................................................................................5
SHIM - end play, crankshaft (.005”)
UAR
BEARING - crankshaft, rear (includes thrust washer) (standard) .................1
BEARING - crankshaft, rear .002” (0.05 mm) undersize ..............................1
WASHER - thrust.........................................................................................2
GASKET - bearing plate ..............................................................................1
PLATE - bearing, rear..................................................................................1
BEARING - camshaft 3/4” length (service part is 5/16” length) ....................2
SEAL - oil, crankshaft rear ...........................................................................1
PIN - drive, bearing stop ..............................................................................4
TUBE - oil ....................................................................................................1
INSERT - valve seat, exhaust (standard).....................................................2
INSERT - valve seat, exhaust .002” (0.05 mm) oversize..............................2
INSERT - valve seat, intake (standard)........................................................2
INSERT - valve seat, intake .005” (0.13 mm) oversize.................................2
INSERT - valve Seat, intake .010” (0.25 mm) oversize ................................2
INSERT - valve seat, intake .025” (0.64 mm) oversize.................................2
BEARING - crankshaft, front, flanged (standard) .........................................1
BEARING - crankshaft, front .002” (0.05 mm) undersize .............................1
GUIDE - valve,exhaust ................................................................................2
GUIDE - valve, intake ..................................................................................2
LOCKWASHER - 3/8”..................................................................................5
PIN - alignment, gear cover .........................................................................2
COVER - valve ............................................................................................1
GASKET - valve cover.................................................................................2
TAPPET - valve (standard) ..........................................................................4
TAPPET - valve .002(0.05 mm) oversize .....................................................4
TAPPET - valve .005(0.13mm) oversize ......................................................4
VALVE - intake ............................................................................................2
VALVE - exhaust .........................................................................................2
BOLT - 1/4” – 20 x 1-3/4”.............................................................................2
SPRING - valve ...........................................................................................4
LOCK - valve and spring..............................................................................8
REQ’D
CYLINDER BLOCK
INDEX
INDEX
CYLINDER BLOCK
REF.
PART NO.
DESCRIPTION
REQ’D
33
36
37
37
38
40
41
42
44
45
45
C40797
C29979
C32279
C32280
C32281
C20248
C32440
C20247
C32282
C29981
C29982
SEAL – intake valve ................................................................................ 2
GASKET - head ...................................................................................... 2
HEAD - cylinder R.H................................................................................ 1
HEAD - cylinder L.H ................................................................................ 1
RETAINER – valve spring ....................................................................... 4
WASHER - 5/16” .................................................................................... 18
BOLT - head 2-3/8” long......................................................................... 16
WASHER - 1/4” copper ........................................................................... 2
CAP - valve ............................................................................................. 4
KIT - gasket, complete engine (does not include bearings) ..................... 1
KIT - gasket, (carbon removal/valve grind) .............................................. 1
OIL BASE, PUMP, FILTER, AND FILLER TUBE
INDEX
MODEL 3016PS, 301BPS, 3020PS, 4016, 4016PS, 401BPS, & 4020PS
INDEX
OIL BASE, PUMP, FILTER AND FILLER TUBE
REF.
PART NO.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
16
17
18
19
20
21
22
23
24
25
2627
28
29
30
31
32
33
34
35
36
37
38
39
C32290
C32465
C32291
C32292
C32293
C32466
C32467
C32289
C29984
192-21
113-252
221-3
C23321
C20565
C20331
113-103
C25389
182-525
C32462
C26191
C29734
C20325
192-19
113-4
C32474
C20574
C20320
C20322
221-86
C19473
C14906
C14399
C33222
182-525
C20577
C33949 **
218-5154 **
DIPSTICK - oil level indicator .................................................................. 1
0-RING ................................................................................................ 1
BRACKET - filltube................................................................................... 1
TUBE - oil fill ............................................................................................ 1
SEAL - tube.............................................................................................. 1
SCREW - # l0 x 1-1/4” panhead ............................................................... 1
NUT - speed (type U) ............................................................................... 1
BASE - oil (includes plugs) ....................................................................... 1
GASKET - oil base ................................................................................... 1
LOCKWASHER - 3/8” .............................................................................. 4
BOLT - 3/8”-16 x 3-3/4 ............................................................................. 4
PLUG - oil base 3/8”................................................................................. 2
CUP - intake, oil pump ............................................................................. 1
ADAPTER - oil filter.................................................................................. 1
WASHER - 5/16” copper .......................................................................... 2
BOLT - 5/16” – 18 x 1”.............................................................................. 2
DRAIN - oil filter ....................................................................................... 1
BOLT - #10-32 x 3/8”................................................................................ 2
GASKET - oil filter adapter ....................................................................... 1
FILTER - oil .............................................................................................. 1
PUMP - oil ................................................................................................ 1
KIT - gasket, oil pump .............................................................................. 1
LOCKWASHER - 1/4” .............................................................................. 2
BOLT - 1/4” – 20 x 1”................................................................................ 2
BOLT - 3/8” – 24 x 7/8” oil bypass ............................................................ 1
WASHER - 3/8” copper ............................................................................ 1
SPRING - oil bypass valve ....................................................................... 1
VALVE - oil bypass................................................................................... 1
REDUCER - pipe 3/8” - 14 to 1/4” ............................................................ 1
NIPPLE - pipe2.5” .................................................................................... 1
GASKET - oil drain ................................................................................... 1
PLUG - oil drain........................................................................................ 1
BAFFLE - air, oil base .............................................................................. 1
BOLT - #10-32 x 3/8”..............................................................................UAR
SEAL - oil filter ......................................................................................... 1
NIPPLE pipe 3.5”...................................................................................... 1
PLUG - 1/2” - 20....................................................................................... 1
REQ’D
** Use PIN and after:
3018PS - 14181900
4020PS - 14184000
GOVERNER GEARCASE AND IGNITION ROTOR
INDEX
INDEX
GOVERNOR GEARCASE AND IGNITION ROTOR
REF.
PART NO.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
C32457
C20305
C22632
C20307
182-84
C20309
C20310
211-5
C20312
C20313
113-120
C20331
C20412
C29985
131-911
C29989
C20345
C32452
C32297
192-19
113-2
GEAR CASE ASSEMBLY - governor.......................................................1
BEARING - governor shaft......................................................................1
SHAFT AND ARM .................................................................................1
YOKE - governor shaft ............................................................................1
SCREW - #8-32 x 3/8” ............................................................................2
PIN - governor cup stop ..........................................................................1
SEAL - oil, governor shaft .......................................................................1
BALL - bearing, governor shaft ...............................................................1
SEAL - oil, crankshaft..............................................................................1
GASKET - mounting ................................................................................1
BOLT - 5/16” – 18 x 1-3/4 ........................................................................4
WASHER - 5/16” copper ..........................................................................5
TUBE - vacuum port (included in assembly) ............................................1
STUD - gear cover ...................................................................................1
NUT - 5/16” - 18 .......................................................................................1
CLIP - retaining ........................................................................................1
GASKET - plate .......................................................................................1
PLATE - plunger cover.............................................................................1
ROTOR - ignition .....................................................................................1
LOCKWASHER - 1/4” ..............................................................................2
BOLT - 1/4” - 20 x 5/8” .............................................................................2
REQ’D
FUEL SYSTEM
INDEX
INDEX
INDEX
FUEL SYSTEM (ENGINE)
REF.
PART NO.
DESCRIPTION
1
C29868
CARBURETOR - fuel (3016PS, 3018PS, 4016, 4016PS, 4018PS)
repairs page 19 ...................................................................................... 1
CARBURETOR - fuel (302OPS, 4020PS) repairs page 19 ...................... 1
GASKET - carburetor mounting ............................................................ 1
SEAL-”O” ring........................................................................................ 1
ADAPTER - carburetor.............................................................................. 1
GASKET - adapter .................................................................................... 1
MAINIFOLD - intake .................................................................................. 1
LOCKWASHER - 1/4” ............................................................................... 2
BOLT - 1/4” – 20 x 1-3/8” .......................................................................... 2
BOLT - 5/16” – 18 x 2”............................................................................... 4
LOCKWASHER - 5/16” ............................................................................. 6
GASKET - manifold ................................................................................... 2
BOLT - 5/16” – 18 x 1”............................................................................... 2
CLIP - retaining, control rod to carburetor ................................................. 1
ROD - governor control ............................................................................. 1
WASHER - 5/16” ....................................................................................... 1
HOSE - fuel (use C28937 cut to length).................................................... 1
PUMP - fuel ............................................................................................... 1
SCREW - tapping #10-24 x 5-8”................................................................ 2
HOSE - vacuum (use C28937 cut to length) ............................................. 1
CLAMP - hose 1/2” (wire)....................................................................... UAR
CAP - fuel outlet ..................................................................................... UAR
CLAMP - hose 7/16” (wire) (use C32376) .............................................. UAR
CLAMP - hose 1/2” (worm drive)............................................................... 1
ELBOW - hose90° ..................................................................................... 1
TUBE - vacuum ......................................................................................... 1
SPRING - governor rod (optional) ............................................................. 1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
C29869
C29969
C29944
C29952
C29953
C40896
192-19
113-65
113-121
192-20
C26202
113-103
C20360
C29988
195-2027
NSS
C29959
182-559
NSS
214-103
C20411
NSS
C32376
C10678
C20412
C33406
INDEX
1
2
3
4
5
5
6
7
8
9
10
11
12
C10678
C28962
NSS
NSS
C11529
C44819
NSS
C23527
C14690
C32376
C31978
C24689
187-1036
REQ’D
FUEL SYSTEM (TRACTOR)
ELBOW - hose 900 ................................................................................... 1
RETAINER - fuel line................................................................................. 1
HOSE - fuel line (use C28937 cut to length) ............................................. 1
TANK - fuel (use C44818, C44819) .......................................................... 1
CAP - fuel tank (includes insert) (1.5”) ...................................................... 1
CAP - fuel tank (1.75”)............................................................................... 1
HOSE - fuel line (use C28937 cut to length) ............................................. 1
LINER - tank.............................................................................................. 1
CUSHION - fuel tank ................................................................................. 2
CLAMP - hose 1/2”.................................................................................... 4
FILTER - fuel ............................................................................................. 1
CLIP - “J” fuel line retaining....................................................................... 1
SCREW -1/4” – 20 self tap ........................................................................ 1
AIR CLEANER AND BREATHER
INDEX
INDEX
AIR CLEANER
REF.
PARTNO.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
C26703
C32302
C22581
C22424
131-911
C32303
187-1036
182-152
195-516
C29946
C32304
C29948
C32376
C32305
C33247
C30033
C32306
131-71
C32451
C33246
C20490
C20493
NSS
C20536
C20504
NUT - wing 1/4” -20 .................................................................................. 1
COVER - air cleaner ................................................................................. 1
PRECLEANER ......................................................................................... 1
ELEMENT - air cleaner............................................................................. 1
NUT - 5/16” - l8 flange .............................................................................. 1
HOUSING - air cleaner ............................................................................. 1
BOLT - 1/4” – 20 x 1/2” tapping, washer head .......................................... 2
SCREW – machine #10 – 32 x 1-1/2” ....................................................... 3
WASHER - #10 ........................................................................................ 3
DEFLECTOR - air..................................................................................... 1
TUBE - air intake ...................................................................................... 1
FILTER - breather..................................................................................... 1
CLAMP - hose .......................................................................................... 1
SUPPORT - air cleaner ............................................................................ 1
TUBE - breather ....................................................................................... 1
GROMMET - rubber ................................................................................. 1
COVER - element..................................................................................... 1
NUT - lock 1/4” - 20 .................................................................................. 1
SPACER - air cleaner stud ....................................................................... 1
HOSE - breather....................................................................................... 1
VALVE - breather cap............................................................................... 1
“0” RING - breather cap............................................................................ 1
SCREW - self tap ..................................................................................... 1
CLAMP - breather cap.............................................................................. 1
SCREEN - breather tube .......................................................................... 2
REQ’D
INDEX
INDEX
CHOKE AND THROTTLE
CARBURETOR
CHOKE AND THROTTLE
INDEX
REF.
1
1
1
2
3
3
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
PART NO.
DESCRIPTION
C33468 *
C37226 * *
C46369 * * *
NSS
C31893 *
C37227 * *
C46340 * * *
C30074
C27233
192-18
C34117
182-559
C22369
C29957
C29506
187-1511
113-1
131-934
C37536 *
C31977 *
113-4 *
129-101 *
C35291
CONTROL - throttle ..................................................................................... 1
HANDLE - throttle control, orange (use C35291) ........................................ 1
CONTROL - choke....................................................................................... 1
CONTROL - choke....................................................................................... 1
CONTROL - choke....................................................................................... 1
HANDLE - choke control, black ................................................................... 1
CLIP - double cable ..................................................................................... 3
LOCKWASHER - No. 10 (early production)................................................. 2
NUT - No. 10 – 24 flange lock...................................................................... 2
BOLT - No. 10 - 24 x 3/4” phillips, black ...................................................... 2
BOLT - washer head #10 - 32 x 5/16”.......................................................... 2
BRACKET - choke cable.............................................................................. 1
CLIP - retaining, choke cable....................................................................... 1
SCREW - tapping #10-32 x 1/2” .................................................................. 1
BOLT - 1/4” - 20 x 1/2” ................................................................................. 1
NUT - 1/4” - 20 flange lock........................................................................... 1
BRACKET - wire stand off ........................................................................... 1
CLIP - wire ................................................................................................... 2
BOLT - 1/4” - 20 x 1” .................................................................................... 1
NUT - 1/4” - 20 ............................................................................................. 1
KNOB - choke and throttle – USE PIN 14176500 and after ........................ 2
* Use before PIN 14176500
REQ’D
* * Use pin 14176500 to 14190552
* * * Use PIN 14190553 and after
CARBURETOR
INDEX
1
2
2
3
4
5
6
7
8
9
C43678 *
C43679 *
C43681
C43682
C29868 * *
C29869 * *
C29965
C29966
C30015
C29967
C29962
NSS
C29969
NSS
NSS
NSS
NSS
CARBURETOR - fuel (3016PS, 3018PS, 4016, 4016PS, 4018PS) ............ 1
CARBURETOR - fuel (3020PS, 4020PS) .................................................... 1
KIT – carburetor repair............................................................................. 1
KIT – accelerator ..................................................................................... 1
CARBURETOR - fuel (3016PS, 3018PS, 4016, 4016PS, 4018PS) ............ 1
CARBURETOR - fuel (3020PS, 4020PS) .................................................... 1
KIT - float ................................................................................................. 1
JET - power (3016PS, 3018PS, 4016, 4016PS, 4018PS) .................... 1
JET - power (3020PS, 4020PS)............................................................ 1
JET - idler.............................................................................................. 1
KIT - repair ................................................................................................... 1
GASKET AND SEAL PACKAGE ............................................................. 1
GASKET - mounting .............................................................................. 1
SCREW AND PLUG PACKAGE................................................................. 1
VALVE - inlet............................................................................................... 1
VALVE - idle adjust ..................................................................................... 1
SPRING - tension ....................................................................................... 2
* For Spec “G” Engines
* * For Spec “C” Engines
INDEX
BLOWER HOUSING AND GOVERNOR
MODEL 3016PS, 301SPS, 3020PS, 4016, 4016PS, 4018PS, 4020PS COMPACT TRACTORS
INDEX
BLOWER HOUSING AND GOVERNOR
REF.
PART NO.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
C32308
163-22
C32444
C32445
187-1073
195-102
C32446
187-1073
C32447
195-518
C20376
C29506
C28719
187-1511
182-49
C20371
C32311
121-3
195-102
C20375
NSS
NSS
187-1036
HOUSING - blower ................................................................................. 1
SCREW - tapping, washer head 1/4”-20x7/16......................................... 1
HOUSING - cylinder air L.H .................................................................... 1
HOUSING – cylinder air R.H................................................................... 1
SCREW - tapping, washer head l/4” – 20 x 5/8 ....................................... 2
WASHER - 1/4”....................................................................................... 2
BOLT - 5/16” –18 x 3/4” washer head ..................................................... 2
SCREW - 1/4” – 20 x 5/8” tapping, washer head..................................... 4
CLAMP - wire.......................................................................................... 1
WASHER - 1/4”....................................................................................... 4
SPRING - governor................................................................................. 1
CLAMP - cable........................................................................................ 1
BRACKET - cable ................................................................................... 1
SCREW - tapping #10 – 32 x 1/2” ........................................................... 1
SCREW - tapping # 6-32 x 5/8”............................................................... 1
SPRING - idle setting.............................................................................. 1
ARM - governor ...................................................................................... 1
BOLT - 1/4” - 20 x 1/2” washer head....................................................... 2
WASHER - 1/4”....................................................................................... 2
BUSHING - arm, governor ...................................................................... 1
SCREEN - blower housing (not used) ..................................................... 1
PLUG - screen (not used) ....................................................................... 1
BOLT - 1/4” – 20 x 1/2” flangelock ........................................................UAR
REQ’D
EXHAUST PIPES AND SHIELDS
INDEX
INDEX
MUFFLER AND SHIELDS
INDEX
EXHAUST PIPES AND COVERS
REF.
PART NO.
DESCRIPTION
1
2
3
4
5
6
7
8
9
C32321
C32322
C26207
C32324
C32325
61-512
192-404
NSS
C31417
129-102
C32455
187-1908
193-70
COVER - exhaust pipe L.H..................................................................... 1
COVER – exhaust pipe R.H ................................................................... 1
GASKET - exhaust ................................................................................. 2
PIPE – exhaust R.H ............................................................................... 1
PIPE - exhaust L.H................................................................................. 1
BOLT - 5/16 x 5/8” socket head.............................................................. 4
LOCKWASHER - 5/16”........................................................................... 4
SCREW - 1/4” -20 x 3/8” washer head (use C31 597) ............................ 2
CLAMP - exhaust ................................................................................... 2
NUT - 5/16” - 18 ................................................................................. 2
CLIP - “J” wire ........................................................................................ 1
SCREW - #10 - 16 x 5/8”........................................................................ 1
LOCKWASHER - #10 external tooth ...................................................... 1
10
11
12
REQ’D
MUFFLER AND SHIELDS
1
2
3
4
5
6
7
8
9
10
C31597
C31415
C33425
113-208
192-21
C31420
C31421
113-3
131-934
187-1036
SCREW - 1/4” – 20 x ½ black.................................................................. 2
SHIELD - head baffle extension L.H........................................................ 1
MUFFLER - exhaust................................................................................ 1
BOLT - 3/8” – 16 x 1-1/4”......................................................................... 2
LOCKWASHER - 3/8” ............................................................................. 2
STRAP - mounting .................................................................................. 1
SHIELD - muffler ..................................................................................... 1
BOLT - 1/4” – 20 x 3/4” hex ..................................................................... 2
NUT - 1/4” – 20 flangelock....................................................................... 2
SCREW - 1/4” -20 x 1/2” self-tap ............................................................. 4
INDEX
INDEX
3016PS, 3018PS, 3020PS, 4016, 4016PS, 4018PS, 4020PS
PTO ELECTRIC CLUTCH
1
1
1
2
3
4
5
6
7
8
9
9
9
10
11
12
13
NSS *
C46993 +
C33198 * *
C32382 * *
C32383 * *
C32384 * *
C32381
C33199
113-206
192-21
C29811
C15557
C33200
C31615
C31976
114-203
C47442
C47422
113-207
192-21
CLUTCH - PTO (use C33201 kit – includes items 1, 8, 9, and 12) ...........................1
CLUTCH-PTO ............................................................................................................1
CLUTCH-PTO ............................................................................................................1
ARMATURE - clutch ............................................................................................1
ROTOR - clutch ...................................................................................................1
FIELD - clutch ......................................................................................................1
KIT - spring and nut .............................................................................................1
BRACKET - anti-rotation ............................................................................................1
BOLT - 3/8” - 16 x 3/4” (secure with LOCK TITE)......................................................1
LOCKWASHER - 3/8” ................................................................................................2
SPACER - clutch .100”.......................................................................................... UAR
WASHER - clamping..................................................................................................1
KEY - 1/4” x 1/4” x 1-1/4” ...........................................................................................1
BOLT - 3/8” 24 x 1-1/2” ..............................................................................................1
KIT – Anti Rotation Bracket........................................................................................1
BRACKET - anti-rotation .....................................................................................1
BOLT - 3/8” - 16 x 1” (secure with LOCK TITE) ..................................................1
LOCKWASHER - 3/8”..........................................................................................1
*
**
Use before these PIN’s:
3016 – 14126917 to S/N 17191880
3018 – 14132580 to S/N 17191880
3020 – 14133202 to S/N 17191880
4016 – 14128593 to S/N 17191880
4018 – 14129744 to S/N 17191880
4020 – 14130984 to S/N 17191880
+
Use after SN 17191880
INDEX
FRAME, FOOTPADS AND BELLY PAN
FRAME, FOOT PADS AND BELLY PAN
INDEX
AFTER PIN #’s
3018PS - before PIN 14181900
4020PS - before PIN 14184000
3016PS, 3020PS, 4016, 4016PS, 4018PS – ALL
REF.
PART NO.
DESCRIPTION
1
1
1
2
3
4
5
6
7
9
10
10
10
10
11
12
12
C33512
C34168
C33514
C31610
C24137
C22023
131-1318
C27508
131-1352
113-208
C30458
C30460
C30462
C30464
121-106
C31368
C33488
13
14
15
15
16
17
18
18
19
20
20
C14730
192-23
113-424
166-85
138-2073
C16373
C31597
C33576
C30274
C31359
C33548
21
21
187-1036
C33576
22
23
23
C31967
C31369
C33580
24
24
C35067
NSS
FRAME - main (3016PS, 301 8PS, 3020PS)........................................... 1
FRAME - main (4016) shown .................................................................. 1
FRAME - main (4016PS, 4018PS, 4020PS)............................................ 1
SHIELD - oil tank..................................................................................... 1
SPRING - latch........................................................................................ 1
HINGE - frame ........................................................................................ 2
NUT - lock 112” N.F ................................................................................ 2
PIN - attachment ..................................................................................... 2
NUT - lock 3/8” N.C. flange ..................................................................... 4
BOLT - 3/8” - 16 x 1-1/4” ........................................................................ 4
FOOTREST L.H. (3016PS, 3018PS, 3020PS) ........................................ 1
FOOTREST R.H. (3016PS, 3018PS, 3020PS) shown ............................ 1
FOOTREST L.H. (4016, 4016PS, 4018PS, 4020PS) .............................. 1
FOOTREST R.H.(4016, 4016PS, 4018PS, 4020PS)............................... 1
BOLT- 5/16” x 1/2” N.C. flange lock......................................................... 4
CAP – instrument panel (4016) shown .................................................... 4
CAP - instrument panel (3016PS, 3018PS, 3020PS,
4016PS, 4018PS, 4020PS) ................................................................ 1
SPACER - rear, frame (3016PS, 3018PS, 3020PS) ................................ 2
LOCKWASHER - 1/2” ............................................................................. 4
BOLT - 1/2” - 13 x 1” transaxle mounting............................................... UAR
BOLT - 1/2” x 1”, 12 Pt. flange............................................................... UAR
PIN - roll 3/16” x 1-1/4” ............................................................................ 2
PIN - latch ............................................................................................... 2
SCREW - 114” - 20 x 1/2” black ............................................................. 4
SCREW - 1/4” - 20 x 5/16” black ............................................................. 8
LENS - display ........................................................................................ 1
COVER - access (4016) shown............................................................... 1
COVER - access (3016PS, 3018PS, 3020PS,
4016PS, 4018PS, 4020PS) ................................................................ 1
SCREW - 1/4” - 20 x 1/2” self tap (4016) ................................................. 2
SCREW - 1/4” - 20 x 5/16” black (3016PS, 3018PS, 3020PS
4016PS, 4018PS, 4020PS) ................................................................ 3
SCREEN - tower side.............................................................................. 2
PAN - belly (4016) shown........................................................................ 1
PAN - belly (3016PS, 3018PS, 3020PS,
4016PS, 4018PS, 4020PS) ................................................................ 1
RETAINER - belly pan 1” ........................................................................ 6
RETAINER - belly pan short (use C35067 cut to length) ......................... 1
REQ’D
INDEX
FRAME, FOOTPADS AND BELLY PAN
MODEL 3016PS, 3018PS, 3020PS, 4016, 4016PS, 401BPS, 4020PS COMPACT TRACTORS
FRAME, FOOT PADS AND BELLY PAN
3018PS - PIN 14181900 and after
4020PS - PIN 14184000 and after
INDEX
BEFORE PIN #’s
REF.
PART NO.
DESCRIPTION
1
1
2
3
4
5
6
7
9
10
10
10
10
11
12
13
14
15
15
16
17
18
18
19
20
21
22
23
24
24
25
25
26
26
27
28
29
30
30
C44830
C44831
C31610
C24137
C22023
131-1318
C27508
131-1352
113-233
C37132
C37134
C37136
C37138
121-106
C37167
C14730
192-23
113-424
166-85
138-2073
C16373
C31597
C33576
C30274
C33548
C33576
C31967
C33580
C35067
NSS
C45049
C15410
C45050
195-2029
195-520
192-20
113-101
C37140
C37141
FRAME - main (3018PS)..........................................................................1
FRAME - main (4020PS)..........................................................................1
SHIELD - oil tank......................................................................................1
SPRING - latch.........................................................................................1
HINGE - frame .........................................................................................2
NUT - lock 1/2” N.F ..................................................................................2
PIN - attachment ......................................................................................2
NUT - lock 3/8” N.C. flange ......................................................................4
BOLT - 3/8” - 16 x 1-3/4” ..........................................................................4
FOOTREST L.H. (3018PS) ......................................................................1
FOOTREST R.H. (3018PS) shown ..........................................................1
FOOTREST L.H. (4020PS) ......................................................................1
FOOTREST R.H. (4020PS)......................................................................1
BOLT - 5/16” x 1/2” N.C. flange lock.........................................................4
CAP - instrument panel ............................................................................1
SPACER - rear, frame..............................................................................2
LOCKWASHER - 1/2” ..............................................................................4
BOLT - 1/2” - 13 x 1” transaxle mounting............................................... UAR
BOLT - 1/2” x 1”, 12 pt. flange ............................................................... UAR
PIN - roIl 3/16” x 1-1/4”.............................................................................2
PIN - latch ................................................................................................2
SCREW - 1/4” - 20 x 1/2” black ................................................................4
SCREW - 1/4” - 20 x 5/16” black ..............................................................8
LENS - display .........................................................................................1
COVER - access ......................................................................................1
SCREW - 1/4” - 20 x 5/16” black ..............................................................3
SCREEN - tower side...............................................................................2
PAN - belly ...............................................................................................1
RETAINER - belly pan 1” .........................................................................5
RETAINER - belly pan 3/8” (use C35067 cut to length) ............................1
CUSHION - L.H........................................................................................2
CUSHION - R.H .......................................................................................2
WASHER - L.H.........................................................................................2
WASHER - R.H ........................................................................................2
WASHER - 5/16” ......................................................................................2
LOCKWASHER - 5/16” ............................................................................2
BOLT - 5/16” - 18 x 1/2” ...........................................................................2
PAD - footrest L.H ....................................................................................1
PAD - footrest R.H. (shown) .....................................................................1
REQ’D
INDEX
HOOD AND GRILLE
INDEX
HOOD AND GRILLE
REF.
PART NO.
DESCRIPTION
1
C31353
C37312
C16362
132-334
C29314
C30126
C30004
C33467
C31611
121-106
C45043
131-934
C31597
187-1328
C31366
C31612
HOOD ......................................................................................................1
HINGE-hood (not shown) is welded to hood.......................................1
ROD - hood hinge ....................................................................................1
PIN - cotter 1/8” x 3/4” ..............................................................................1
BUTTON – push, hood release ................................................................1
ROD - push, hood release........................................................................1
SPRING - release ....................................................................................1
LATCH - hood ..........................................................................................1
BRACKET – hood stop.............................................................................2
BOLT - 5/16” –18 x 1/2” flangelock...........................................................4
GRILLE ....................................................................................................1
NUT - 1/4” - 20 flange lock .......................................................................2
SCREW - 1/4” – 20 x 1/2” black ...............................................................2
SCREW - #8 - 18 x 3/8”............................................................................1
SHROUD - headlight ................................................................................1
SHIELD - heat ..........................................................................................1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
REQ’D
INDEX
SEAT, FENDERS AND TOOL TRAY
SEAT, FENDERS AND TOOL TRAY
INDEX
AFTER PIN #’s
3016PS, 3020PS, 4016, 4016PS, 4018PS - All
3018PS - before PIN 14181900
4020PS - before PIN 14184000
REF.
1
1
2
2
3
3
4
4
5
5
6
7
8
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
27
27
27
28
29
PARTNO.
DESCRIPTION
C31020
C31021
C26827
C27224
113-427
113-441
113-424
113-118
192-20
192-23
C31004
C16429
C30071
C30066
C29812
195-2175
113-102
C31006
121-106
C33474
C26526
C14728
C27594
195-525
C17216
C30489
131-1216
C29305
C29306
113-102
131-911
C30942
C32386
C32385
C32388
C32387
182-547
131-934
SUPPORT - seat, front shown (3016PS, 3018PS, 3020PS).....................1
SUPPORT - seat, front (4016, 4016PS, 4018PS, 4020PS) ......................1
SUPPORT - seat, rear (3016PS, 3018PS, 3020PS).................................1
SUPPORT - seat, rear (4016, 4016PS, 4018PS, 4020PS) .......................1
BOLT - 1/2” x 3-1/4” (3016PS, 3018PS, 3020PS) ....................................2
BOLT - 1/2” – 2 -1/4” N.C.hex (4016,4016PS,4018PS,4020PS) ..............2
BOLT - 1/2” x 1” N.C. hex.........................................................................1
BOLT - 5/16” x 5/8” ..................................................................................1
LOCKWASHER - 5/16” ............................................................................1
LOCKWASHER - 1/2” ..............................................................................4
TRAY - tool ..............................................................................................1
PIN - seat hinge .......................................................................................1
SEAT - shown (black) (3016PS, 3018PS, 3020PS)..................................1
SEAT - black (4016, 4016PS, 4018PS, 4020PS) .....................................1
WASHER - special ...................................................................................4
WASHER - 5/16” x 1-1/4” OD, zinc...........................................................4
BOLT - 5/16” x 3/4” ..................................................................................4
SPRING – seat switch..............................................................................1
BOLT - 5/16” x 1/2” flangelock.................................................................10
HINGE ASSEMBLY - seat........................................................................1
CAP - spring.............................................................................................1
GRIP – shift lever .....................................................................................1
LEVER - shift............................................................................................1
WASHER - 7/16” ......................................................................................1
SPRING - shift lever .................................................................................1
WASHER .................................................................................................1
NUT – Iock 3/8” N.C.hex ..........................................................................1
CAP - spring.............................................................................................2
SPRING - seat .........................................................................................2
BOLT - 5/16” – 18 x 3/4”...........................................................................3
NUT - 5/16” - 18 flangelock ......................................................................7
REFLECTOR - red, rear fender................................................................2
FENDER - R.H. (3016PS, 3018PS, 3020PS) ...........................................1
FENDER - LH. shown (3016PS, 3018PS, 3020PS)..................................1
FENDER - R.H. (4016, 4016PS, 4018PS, 4020PS) .................................1
FENDER - L.H. (4016, 4016PS, 4018PS, 4020PS) ..................................1
SCREW - 1/4” – 20 x 1/2”.........................................................................2
NUT - 1/4” ................................................................................................2
REQ’D
INDEX
SEAT, FENDER AND TOOL TRAY
SEAT, FENDER AND TOOL TRAY
Use PIN and AFTER:
3018PS - use PIN 14181900 and after
4020PS - use Pin 14184000 and after
INDEX
BEFORE PIN #’s
REF.
PART NO.
DESCRIPTION
1
1
2
2
3
3
4
4
5
5
6
7
8
C44925
C44926
C37266
C37265
113-427
113- 441
113-424
113-118
192-20
192-23
C37017
C16429
C44982
C37848
C37299
113-2
C44929
C44930
C37462
121-106
C37152
C26526
C10487
C44931
C44932
195-525
C10482
132-310
C37460
C29305
C29306
113-102
131-911
C37428
C37430
C37154
C37153
C37156
C37155
C31597
131-934
C42155
C37850
C42056
SUPPORT - seat, front (3018PS).............................................................. 1
SUPPORT - seat, front (4020PS).............................................................. 1
SUPPORT - seat, rear (4O2OPS) ............................................................. 1
SUPPORT-seat, rear (3018PS)................................................................. 2
BOLT - 1/2” x 3 -1/4” (3018PS) ................................................................. 2
BOLT - 1/2” x 2 -1/4” (4O2OPS)................................................................ 2
BOLT - 1/2” x 1” N.C. hex.......................................................................... 1
BOLT - 5/16” x 5/8”.................................................................................... 1
LOCKWASHER - 5/16”.............................................................................. 1
LOCKWASHER - 1/2”................................................................................ 4
TRAY - tool ................................................................................................ 1
PIN - seat hinge......................................................................................... 1
SEAT - operator’s ...................................................................................... 1
KIT – Rail................................................................................................... 1
BRACKET - switch mounting..................................................................... 1
BOLT - 1/4” - 20 x 5/8”............................................................................... 2
COVER - shift lever (3018PS) ................................................................... 1
COVER - shift lever (4020PS) ................................................................... 1
SPRING - seat switch................................................................................ 1
BOLT - 5/16” x 1/2” flange lock................................................................. 10
HINGE ASSEMBLY - seat......................................................................... 1
CAP - spring .............................................................................................. 1
KNOB - shift lever...................................................................................... 1
LEVER - shift (3018PS)............................................................................. 1
LEVER - shift (4O2OPS) ........................................................................... 1
WASHER - 7/16” ....................................................................................... 1
SPRING - shift lever .................................................................................. 1
PIN - cotter 1/8” x 1” .................................................................................. 1
COVER - plate........................................................................................... 1
CAP - spring .............................................................................................. 2
SPRING - seat........................................................................................... 2
BOLT - 5/16” - 18 x 3/4”............................................................................. 3
NUT - 5/16” - 18 flange lock ..................................................................... 11
PLATE - shift pattern (shown) (3018PS) ................................................... 1
PLATE - shift patter (4020PS) ................................................................... 1
FENDER - R.H. (3018PS) ......................................................................... 1
FENDER - L.H. shown (3018PS) .............................................................. 1
FENDER - R.H. (4O2OPS)........................................................................ 1
FENDER - L.H. (4O2OPS) ........................................................................ 1
SCREW - 1/4” - 20 x 1/2”........................................................................... 6
NUT - 1/4”.................................................................................................. 6
PROTECTOR - tail light............................................................................. 2
CUSHION – Seat Rail ............................................................................... 4
SCREW – Phillips, Seat rail mounting....................................................... 4
9
10
11
11
12
13
14
15
16
17
17
18
19
20
21
22
23
24
25
26
26
27
27
27
27
28
29
30
33
34
REQ’D
INDEX
MANUAL STEERING
(4016)
INDEX
MANUAL STEERING (4016)
REF.
PART NO.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
11
12
13
14
15
16
17
18
19
113-206
C26325
C29044
C33940
C29812
113-241
C14201
131-1352
C27501
138-143
195-541
195-2206
C33309
C33308
192-21
195-2069
C15096
C44378
C33945
195-103
BOLT - 3/8” x 3/4” N.C. hex......................................................................4
WHEEL - steering ....................................................................................1
PIN - pivot ................................................................................................1
SHAFT - steering .....................................................................................1
WASHER - 3/8” x 1.4” ..............................................................................2
BOLT - 3/8” – 16 x 3”................................................................................1
WASHER - shim.......................................................................................4
NUT - 3/8” - 16 hex lock (tighten to a torque of 45 ft. lbs.) ........................1
BUSHING.................................................................................................1
PIN - roll 1/4”-2-1/4”..................................................................................1
WASHER - 5/8” ..................................................................................... UAR
WASHER - shim .060”........................................................................... UAR
GEAR - steering .......................................................................................1
BUSHING - sleeve ...............................................................................2
LOCKWASHER - 3/8” ..............................................................................4
WASHER - 5/8” zinc plated ......................................................................1
BUSHING - flanged nylon ........................................................................1
SUPPORT - steering gear (includes item 9) .............................................1
TUBE - steering........................................................................................1
WASHER - 3/8” ........................................................................................2
REQ’D
INDEX
FRONT AXLE
INDEX
REF.
1
1
2
3
3
3
3
3
3
3
4
4
5
6
6
7
8
9
10
10
11
12
13
14
15
16
17
18
19
20
21
22
FRONT AXLE
PART NO.
DESCRIPTION
REQ’D
C18812
C40687
195-545
C45088
C31341
C45086
C31340 *
C33537 *
C40690 **
C40688 **
C27902
C28232
C22278
C11906
C13716
219-404
C13106
132-311
C25855
C25856
C28226
187-1910
C44806
192-23
129-165
129-365
C44641
C44640
C22568
219-17
113-208
129-103
AXLE - front (3016PS, 301 8PS, 3020PS)................................................1
AXLE - front shown (4016, 4016PS, 4018PS, 4020PS) ...........................1
WASHER - spacer ...................................................................................2
SPINDLE - R.H. (3016PS, 3018PS, 3020PS)...........................................1
SPINDLE - R.H. shown (4016) .................................................................1
SPINDLE - L.H. (3016PS, 3018PS, 3020PS) ...........................................1
SPINDLE - L.H. (4016, 4016PS, 4018PS, 4020PS) .................................1
SPINDLE - R.H. (4016PS, 4018PS, 4020PS)...........................................1
SPINDLE - L.H. (4020PS) ........................................................................1
SPINDLE - R.H. (4020PS) shown ............................................................1
RING - retaining, spindle (4016, 4016PS, 4018PS, 4020PS) ..................2
RING - retaining, spindle (3016PS, 3018PS, 3020PS) .............................2
PIN - retaining, axle pivot .........................................................................1
WASHER - thrust (3016PS, 3018PS, 3020PS) ........................................4
WASHER - thrust (4016, 4016PS, 4018PS, 4020PS)...............................4
FITTING - lubrication................................................................................3
COVER - lubrication fitting........................................................................3
PIN - cotter 5/32” x 1-1/4” .........................................................................2
TIE ROD - (4016, 4016PS, 4018PS, 4020PS)..........................................1
TIE ROD - (3016PS, 3018PS, 3020PS) ...................................................1
WASHER - wheel spacer ...................................................................... UAR
BOLT - 3/8” - 16 x 3/4” N.C. hex head......................................................1
LINK - drag (4016) ...................................................................................1
LOCKWASHER - 1/2” zinc .......................................................................4
NUT - 1/2” N.F. R.H. thread, lock .............................................................6
NUT - 1/2” N.F. L.H. thread, lock ..............................................................2
BALL JOINT - 1/2” L.H. thread .................................................................2
BALL JOINT - 1/2” R.H. thread.................................................................2
PIN - axle pivot.........................................................................................1
BOLT - 3/8” - 16 x 1-1/4” ..........................................................................2
NUT - 3/8” - 16 .........................................................................................2
*Use before PIN:
**Use PIN and after:
4020 PS - 14180301
All Other models are before PIN
INDEX
BRAKE ASSEMBLY
INDEX
BRAKE ASSEMBLY
REF.
PART NO.
DESCRIPTION
1
2
3
4
5
5
C33942
C26381
138-2073
C31660
C31662
C33759
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
22
23
24
C31604
C31661
C21942
C31605
C33427
C23910
113-2262
129-143
C23899
C24761
C40646
195-533
132-310
C28978
141-4
132-321
C31993
C31992
C31975
C44380
25
26
27
28
113-206
192-21
195-2063
195-103
PEDAL - brake actuating..........................................................................1
ARM - brake pedal ...................................................................................1
PIN - roII3/16”xl-1/4”.................................................................................1
SPRING - return.......................................................................................1
GUIDE - neutral return (shown) 4016 .......................................................1
GUIDE - neutral return (3016PS, 3018PS, 3020PS,
4016PS, 4018PS, 4020PS) ...................................................................1
ACCUATOR - parking brake ....................................................................1
LEVER - brake lock ..................................................................................1
SPRING - brake lock ................................................................................1
CAP - actuator..........................................................................................1
BAND - brake ...........................................................................................1
PIN - clevis...............................................................................................1
BOLT - 3/8” – 16 x 1-1/2” hex...................................................................1
NUT - 3/8” - 16 special .............................................................................1
ARM - brake.............................................................................................1
ARM - brake (includes adjustment nut).....................................................1
GUIDE - brake actuator............................................................................1
WASHER - .531” I.D.................................................................................5
PIN – cotter 1/8” x l.0” ..............................................................................5
CLEVIS ....................................................................................................1
PIN - davis ...............................................................................................1
PIN - cotter...............................................................................................1
ROD - brake (4016, 4016PS, 4018PS, 4020PS) ......................................1
ROD - brake (3016PS, 3018PS, 3020PS) ................................................1
PAD – brake pedal ...................................................................................1
BRACKET - support (3016PS, 3018PS, 3020PS,
4016PS, 4018PS, 4020PS) .....................................................................1
BOLT - 3/8” – 16 x 3/4”.............................................................................4
LOCKWASHER - 3/8” ..............................................................................4
WASHER .................................................................................................1
WASHER - 3/8” ........................................................................................2
REQ’D
FRONT AND REAR WHEELS
1
C30913
1
1
C30917
C30922
2
2
3
4
5
6
7
8
C27763
C10314
C30912
219-403
C44499
C28965
C44478
C28236
C13106
WHEEL - rear, 5 bolt (3016PS, 3018PS, 3020PS)
for 23 x 8.50 - 12 tire .............................................................................2
WHEEL - rear, 6 bolt (4016, 4016PS, 401 8PS, 4020PS) shown .............2
WHEEL - rear, 5 bolt (3016PS, 3018PS, 3020PS)
for 23 X 10.50 – 12 tire..........................................................................2
BOLT - rear wheel (4016, 4016PS, 4018PS, 4020PS) ............................12
BOLT – rear wheel (3016PS,3018PS, 3020PS) ......................................10
WHEEL - front (includes bearings) ...........................................................2
BEARING - wheel ....................................................................................2
CAP - hub, front wheel (optional)..............................................................2
CAP - plastic, front ...................................................................................2
STEM - valve............................................................................................4
COVER - lubrication fitting........................................................................2
INDEX
TRANSMISSION AND FINAL DRIVE
INDEX
REF.
1
2
3
4
5
6
7
8
9
9
9
10
12
12
13
14
14
15
16
17
18
19
20
21
22
23
24
24
24
25
25
26
27
28
29
30
31
32
33
34
36
37
38
38
39
40
40
41
42
43
TRANSMISSION AND FINAL DRIVE
PART NO.
C47666 +
C47668 + +
NSS
C12713
C24804
C24803
C13241
C13385
C13266
C28281
C30029 *
C36902 * *
C46929 * * *
221-3
C16699
C22638
126-128
C16700
C22637
C26342
C13196
C36935
C28241
192-23
121- 21
C12725
C37222
C14168
C14644 *
C36901 * *
C46928 * * *
C30030 *
C36903 * *
C12552 * & * *
NSS
C33305
NSS
NSS
NSS
NSS
NSS
C30031
C12718
C14223
C33417
C46927 * * *
C14222
113-424
166-86
132-310
195-541
138-2073
DESCRIPTION
REQ’D
CASE ASSEMBLY - transmission (includes bearings & seals only) .................................. 1
CASE ASSEMBLY - transmission (includes bearings & seals only) .................................. 1
CASE - transmission (see above) ..................................................................................... 1
BEARING - flange......................................................................................................... 2
BEARING - flange......................................................................................................... 2
SEAL - shaft.................................................................................................................. 3
BEARING - sleeve ........................................................................................................ 1
BEARING - sleeve ........................................................................................................ 1
SEAL - shift rod............................................................................................................. 1
BEARING - roller........................................................................................................... 1
DIFFERENTIAL ASSEMBLY, 20o PA (also includes C30030, C30031, C12552) ............. 1
DIFFERENTIAL ASSEMBLY, 20o PA (also includes C36903, C30031, C12552) ............. 1
o
DIFFERENTIAL ASSEMBLY, 25 PA ................................................................................ 1
PLUG - filler and drain 3/8” ................................................................................................ 3
SHAFT - axle, short R.H. (3000 Series)............................................................................. 1
SHAFT - axle, short R.H. shown (4000 Series) ................................................................. 1
KEY - Woodruff, brake idler #18, 1/4” x 1-1/8” ................................................................... 1
SHAFT - axle, long L.H. (3000 Series)............................................................................... 1
SHAFT - axle, long L.H. shown (4000 Series) ................................................................... 1
RING - retainer, axle .......................................................................................................... 2
GASKET - transmission cover ........................................................................................... 1
COVER transmission ......................................................................................................... 1
BREATHER - transmission ................................................................................................ 1
LOCKWASHER - 1/2” ........................................................................................................ 4
BOLT - 1/4” x 1/2” N.C. hex lock........................................................................................ 6
FORK-shift ......................................................................................................................... 1
ROD - gear shift................................................................................................................. 1
RING - retaining................................................................................................................. 2
GEAR - cluster input, 18 tooth & 32 tooth, 20o PA ............................................................. 1
GEAR - cluster input 18 tooth & 27 tooth, 20o PA ............................................................ UAR
o
GEAR - cluster input 18 tooth & 27 tooth, 25 PA ............................................................ UAR
GEAR - high 41 tooth, 20o PA............................................................................................ 1
GEAR - high range, 46 tooth, 20o PA................................................................................. 1
o
o
GEAR - low 55 tooth, 20 PA (NSS on a 25 PA gear, order assembly (ref # 9)................ 1
DIFFERENTIAL CASE....................................................................................................... 1
BRAKE DRUM ................................................................................................................... 1
GEAR - differential pinion .................................................................................................. 2
GEAR - differential ............................................................................................................. 2
WASHER - pinion thrust .................................................................................................... 2
PIN - differential ................................................................................................................. 1
PIN - differential pin lock .................................................................................................... 1
KIT - screw (set of four) ..................................................................................................... 1
WASHER - differential ....................................................................................................... 2
WASHER - spacer ........................................................................................................... UAR
GEAR - brake idler, 20o PA................................................................................................ 1
o
GEAR - brake idler, 25 PA................................................................................................ 1
RING - retainer, brake idler................................................................................................ 1
BOLT - 1/2” - 13 x 1” hex ................................................................................................. UAR
BOLT - 1/2” - 13 x 1-1/4”.................................................................................................. UAR
PIN - cotter 1/8” x 1” ........................................................................................................ UAR
WASHER - .656” ID x 1.312 OD ........................................................................................ 1
PIN - spiral 3/1 6” x 1-1/4”................................................................................................ UAR
*
Use before PIN:
3018PS – 14181900, 4020PS - 14184000
+
**
Use PIN:
3018PS - 14181900 to 17192412
4020PS - 14184000 to 17192398
+ + All units before PIN 17193395
* * * Use Pin and after:
3018PS – 17192413, 4020PS - 17192399
These are 25o pressure angle gears and must not be
used with 20o PA gears
Use PIN and After:
All units PIN 17193395 and after
INDEX
HYDRAULIC SYSTEM (4016)
MODEL 3016PS, 301BPS, 3020PS, 4016, 4016PS, 401BPS, 4020PS COMPACT TRACTORS
INDEX
REF.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
HYDRAULIC SYSTEM
4016
PARTNO.
DESCRIPTION
C33473
218-5065
218-5007
218-5107
218-5007
218-5062
218-5007
218-5232
C27764
131-351
C29657
C29658
C31435
C33234
C28949
166-85
C31958
C33423
C33180
C34175
C31295
C33555
214-254
214-14
C31966
218-5117
C31973
C31974
C33559
218-754
C33577
C33446
121-21
217-333
C33445
C33544
C33556
C29697
VALVE - control (repairs page 57)............................................................1
FITTING - 3/4” x 5/8” “0” ring....................................................................1
“0” RING...................................................................................................1
FITTING - 90°elbow .................................................................................2
“0” RING...................................................................................................1
FITTING - 5/8” x 7/8” “0” ring....................................................................3
“0” RING...................................................................................................1
FITTING - 90° elbow ................................................................................1
SCREW - 5/16” - 18 x 1-1/4” round head..................................................2
NUT - lock 5/16” .......................................................................................2
TUBE - valve to upper motor port .............................................................1
TUBE - valve to lower motor port..............................................................1
TUBE - valve “out” to heat exchanger ......................................................1
MOTOR - hydraulic (repairs page 55) ......................................................1
SEAL - motor to transmission...................................................................1
SCREW - 1/2”-18 x 1” l2pt. flange ............................................................4
PUMP - hydraulic 1/2” shaft (repairs page 53)..........................................1
HOSE - pump inlet ...................................................................................1
RESERVOIR - oil .....................................................................................1
CAP - reservoir.........................................................................................1
EXCHANGER - heat ................................................................................1
HOSE - formed 90° ..................................................................................1
CLAMP – hose 1-1/4”...............................................................................8
CLAMP - hose 1-3/8”................................................................................2
HOSE - pump to valve..............................................................................1
FITTING - 90° elbow ................................................................................1
“J” NUT - 1/4” - 20 ....................................................................................4
“U” Clip - retainer......................................................................................4
FITTING - tee, 3/8” tube x 1/2” - 20 ..........................................................1
CAP - 3/8” tube ..................................................................................... UAR
BRACKET - oil filter..................................................................................1
HEAD - oil filter.........................................................................................1
BOLT - 1/4” – 20 x 1/2”.............................................................................4
FITTING - 90°3/8” NPTF x 3/4” barb stem................................................2
FILTER - oil..............................................................................................1
TUBE - filter to tank ..................................................................................1
HOSE - formed 90° ..................................................................................1
HOSE - 3/4” x 4”.......................................................................................2
REQ’D
INDEX
HYDRAULIC SYSTEM
INDEX
HYDRAULIC SYSTEM
3016PS, 3020PS (301BPS before PIN 14181900)
4016PS, 4018PS, (4020PS before PIN 14184000)
REF.
PART NO.
DESCRIPTION
1
2
3
4
5
6
7
9
10
11
11
12
12
13
14
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
C33473
218-5065
218-5007
218-5107
218-5007
218-5062
218-5007
C27764
131-351
C29655
C29657
C29656
C29658
C31435
C30939
C33234
C28949
166-85
C33579
C33551
C33180
C37093
C31295
C33555
214-254
214-14
C33557
218-5117
C31973
C31974
C33559
218-754
C33577
C33446
121-21
217-333
C33445
C33544
C33556
NSS
217-366
C33766
C25245
C33765
C33834
C33218
113- 102
131- 911
195- 521
VALVE - control (repairs page 57)............................................................1
FITTING - 3/4” x 5/8” ................................................................................1
“0” RING..................................................................................................1
FITTING - 900 elbow................................................................................2
“0” RING..................................................................................................1
FITTING - 5/8” x 7/8” “0” ring................................................................. UAR
“0” RING..................................................................................................1
SCREW - 5/16” - 18 x 1-1/4” round head..................................................2
NUT - lock 5/16” .......................................................................................2
TUBE - valve to upper motor port (301 6PS, 301 8PS, 3020PS) ..............1
TUBE - valve to upper motor port (401 6PS, 401 8PS, 4020PS) ..............1
TUBE - valve to lower motor port (301 6PS, 301 8PS, 3020PS)...............1
TUBE - valve to lower motor port (401 6PS, 401BPS, 4020PS) ...............1
TUBE - valve “out” to heat exchanger ......................................................1
MOTOR - hydraulic (repairs page 55) (301 6PS, 301BPS, 3020PS) ........1
MOTOR - hydraulic (401 6PS, 401BPS, 4020PS) (repairs page 55) ........1
SEAL - motor to transmission...................................................................1
SCREW - 1/2” - 13 x 1” 12 pt. flange ........................................................4
PUMP - hydraulic 3/4” shaft (repairs page 53)..........................................1
HOSE - pump inlet ...................................................................................1
RESERVOIR-oil .......................................................................................1
CAP - reservoir.........................................................................................1
EXCHANGER - heat ................................................................................1
HOSE - formed 90° ..................................................................................1
CLAMP - hose 1-1/4”................................................................................8
CLAMP - hose 1-3/8”................................................................................2
HOSE - pump to regulator ........................................................................1
FITTING - 90° elbow ................................................................................2
“J” NUT - 1/4” - 20 ....................................................................................4
“U” Clip - retainer......................................................................................4
FITTING - tee, 3/8” tube x 1/2” - 20 ....................................................... UAR
CAP - 3/8” tube ..................................................................................... UAR
BRACKET - oil filter..................................................................................1
HEAD - oil filter.........................................................................................1
BOLT - 1/4” - 20 x 1/2...............................................................................4
FITTING - 90°3/8” NPTF x 3/4” barb stem................................................2
FILTER - oil..............................................................................................1
TUBE - filter to tank ..................................................................................1
HOSE - formed 90° ..................................................................................1
HOSE - 3/4” x 4” (use C29697 cut to length) ............................................2
FITTING - 90° 1” hose x 1-1/16” - 20 UNF................................................1
TUBE - hydraulic ......................................................................................1
FITTING - hydraulic..................................................................................1
HOSE - regulator valve “by pass” to travel valve ......................................1
BRACKET - support .................................................................................1
CLAMP-tube ............................................................................................1
BOLT - 5/16” -18 x 3/4” ............................................................................2
NUT - 5/16” - 18 flange.............................................................................2
WASHER - 5/16” ......................................................................................1
REQ’D
INDEX
HYDRAULIC SYSTEM
MODEL 3016PS, 3018PS, 3020PS, 4016, 4016PS, 4020PS COMPACT TRACTORS
HYDRAULIC SYSTEM
(3018PS PIN 14181900 and after)
INDEX
REF.
PART NO.
DESCRIPTION
1
2
3
4
5
6
7
9
10
11
11
12
12
13
14
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
40
41
42
43
44
44
45
46
47
48
C33473
218-5065
218-5007
218-5107
218-5007
218-5062
218-5007
C27764
131-351
C37220
C29657
C37221
C29658
C31435
C30939
C33234
C28949
166-86
C33579
C33551
C33180
C37093
C31295
C33555
214-254
214-14
C33557
218-5117
C31973
C31974
C37425
218-753
C33577
C33446
121-21
217-333
C33445
C33544
C33556
NSS
217-366
C44920
C44921
C25245
192-23
C44908
C44922
C44923
218-5107
218-5137
C45045
C44911
VALVE - control (repairs page 57)......................................................................... 1
FITTING - 3/4” x 7/8” ............................................................................................. 1
“0” RING ............................................................................................................... 1
FITTING - 900 elbow ............................................................................................. 2
“0” RING ............................................................................................................... 1
FITTING - 5/8” x 7/8” “0” ring .............................................................................. UAR
“0” RING ............................................................................................................... 1
SCREW - 5/16” - 18 x 1-1/4” round head .............................................................. 2
NUT - lock 5/16”..................................................................................................... 2
TUBE - valve to upper motor port (3018PS).......................................................... 1
TUBE - valve to upper motor port (4020PS).......................................................... 1
TUBE - valve to lower motor port (3018PS) ...........................................................I
TUBE - valve to lower motor port (4020PS) .......................................................... 1
TUBE - valve “out” to heat exchanger ................................................................... 1
MOTOR - hydraulic (repairs page 55) (3018PS) ................................................... 1
MOTOR - hydraulic (4020PS) (repairs page 55) ................................................... 1
SEAL - motor to transmission ................................................................................ 1
SCREW - 1/2” - 13 x 1” 12 pt. flange..................................................................... 4
PUMP - hydraulic 3/4” shaft (repairs page 53) ...................................................... 1
HOSE - pump inlet................................................................................................. 1
RESERVOIR - oil................................................................................................... 1
CAP - reservoir ...................................................................................................... 1
EXCHANGER - heat.............................................................................................. 1
HOSE - formed 90°................................................................................................ 1
CLAMP - hose 1-1/4” ............................................................................................. 8
CLAMP - hose 1-3/8” ............................................................................................. 2
HOSE - pump to regulator ..................................................................................... 1
FITTING - 90° elbow.............................................................................................. 2
“J” NUT - 1/4” - 20.................................................................................................. 4
“U” Clip - retainer ................................................................................................... 4
FITTING 90°, 3/8” x 1/2” - 20.............................................................................. UAR
CAP - 1/2” - 20....................................................................................................... 1
BRACKET - oil filter ............................................................................................... 1
HEAD - oil filter ...................................................................................................... 1
BOLT - 1/4” - 20 x 1/2”........................................................................................... 4
FITTING - 90° 3/8” NPTF x 3/4” barb stem .......................................................... 2
FILTER - oil............................................................................................................ 1
TUBE - filter to tank ............................................................................................... 1
HOSE - formed 90°................................................................................................ 1
HOSE - 3/4” x 4” (use C29697 cut to length)......................................................... 2
FITTING - 90° 1” hose x 1-1/16” - 20 UNF ............................................................ 1
TUBE - regulator valve “by pass” to PTO valve “in” (3018PS) .............................. 1
TUBE - regulator valve “by pass” to PTO “in” (4020PS)... ................................... 1
FITTING - hydraulic ............................................................................................... 1
LOCK WASHER - 1/2”........................................................................................... 4
FITTING - elbow .................................................................................................... 1
TUBE - PTO “out” to travel valve “in” (3018PS) .................................................... 1
TUBE - PTO “out” to travel valve “in” (4020PS) .................................................... 1
FITTING - 90° 7/8” - 14 (301 8PS) upper port ....................................................... 1
FITTING - 45° 7/8” - 14 x 5/8” (301 8PS) lower port ............................................. 1
CUSHION - tube .................................................................................................... 1
FITTING - “T” return............................................................................................... 1
REQ’D
INDEX
POWER STEERING
MODEL 3016PS, 3018PS, 3020PS, 4016, 4016PS, 4018PS, 4020PS. COMPACT TRACTORS
POWER STEERING
3016PS 3018PS, 3020PS
4016PS, 4018PS, 4020PS
INDEX
REF.
1
2
3
4
4
4
5
6
7
8
9
10
10
11
11
12
13
14
15
16
17
18
18
19
19
20
21
22
23
24
25
26
27
28
29
30
31
PART NO.
C44640
192-23
129-165
NSS*
C44628 * *
C44852 * *
C14717
132-91
C33554
C33763
C15410
C27990*
C37302**
C16945*
C42591 **
129-127
C33743
129-162
218-5105
218-5135
218-5005
C33560
C32399
C33561
C33750
C28275
C22947
C33545
121-21
C33762
218-5128
195-2175
131-69
113-132
131-934
C39504 **
C39507 **
DESCRIPTION
REQ’D
BALLJOINT - 1/2” R.H. thread ............................................................................................1
LOCKWASHER - 1/2” .........................................................................................................1
NUT - 1/2” N.F. lock............................................................................................................2
CYLINDER - hydraulic (use C44628 to service all).............................................................1
CYLINDER - hydraulic ........................................................................................................1
KIT - seal, hydraulic cylinder............................................................................................1
PIN - clevis 5/8” dia.............................................................................................................1
PIN - cotter 3/16” x 1”..........................................................................................................1
VALVE - regulator...............................................................................................................1
BRACKET - mounting .........................................................................................................1
WASHER - cushion.............................................................................................................2
WHEEL - steering (shown) .................................................................................................1
WHEEL - steering ...............................................................................................................1
CAP - steering wheel ..........................................................................................................1
CAP - steering wheel ..........................................................................................................1
NUT - 5/8” - 18....................................................................................................................1
PUMP - steering .................................................................................................................1
NUT - 5/16” - 24..................................................................................................................3
FITTING - 900 adjustable elbow 3/8” x 9/16” - 18...............................................................1
FITTING - 45° adjustable elbow 3/8” x 9/16” - 18 ...............................................................1
“0” RING .........................................................................................................................1
HOSE - hydraulic 23” (3016PS, 3018PS, 3020PS) ............................................................1
HOSE - hydraulic 16” hand pump “out” to travel valve........................................................1
TIE - nylon ..........................................................................................................................1
STRAP - mounting..............................................................................................................1
BOLT - 1/4” - 20 x 1/2” ........................................................................................................2
HOSE - regulator valve (reg) to hand pump (in) .................................................................1
FITTING - hydraulic 90°, regulator valve (reg.) ...................................................................1
WASHER - 5/16”.................................................................................................................1
NUT - lock 5/16” - 18...........................................................................................................1
BOLT - 1/4” - 20 x 1-3/4”.....................................................................................................2
NUT - flange lock 1/4” - 20..................................................................................................2
BOOT - steering column .....................................................................................................1
INSERT - boot ....................................................................................................................1
*Use before PIN:
301 8PS - 14181900
4020PS - 14184000
All others before PIN
MANUAL PUMP (POWER, STEERING)
REF.
1
2
3
4
5
6
7
8
9
10
PART NO.
C33743
129-127
C34485
C30281
NSS
NSS
NSS
NSS
NSS
NSS
C34484
C34483
DESCRIPTION .............................................................................................................. REQ’D
PUMP - steering, manual....................................................................................................1
NUT - 5/8” - 18.................................................................................................................1
KIT - cover and manifold..................................................................................................1
KIT - cover and manifold..................................................................................................1
“0” RING ......................................................................................................................4
RING - seal ..................................................................................................................5
“0” RING ......................................................................................................................1
SEAL - commutator......................................................................................................1
SEAL - face..................................................................................................................1
RING - back-up............................................................................................................1
VALVE - relief ....................................................................................................................1
PLUG - relief valve.............................................................................................................1
INDEX
HYDRAULIC PUMP
USE ON 4016
USE ON POWER STEERING UNITS
HYDRAULIC PUMP (PARKER-HANNIFIN)
Use on model 4016
INDEX
REF.
PART NO.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
C31958
F53109
C31987
C15731
C15732
C15733
C15734
C15735
NSS
C15737
C15738
C15739
C15740
113-111
C31988
C19115
PUMP - hydraulic 1/2” shaft......................................................................1
PIN - dowel............................................................................................2
COVER - rear........................................................................................1
GEAR ASSEMBLY - driven ...................................................................1
“0” RING - cover ....................................................................................2
BODY - pump........................................................................................1
COVER - front .......................................................................................1
SEAL -shaft ...........................................................................................1
GEAR ASSEMBLY - drive (1/2” shaft) (use C31958).............................1
PLATE - wear........................................................................................1
SHIELD - heat .......................................................................................1
GASKET ...............................................................................................1
SEAL.....................................................................................................1
BOLT.....................................................................................................4
KEY - 1/8” square 3/4” long (1.587 mm x 19.05mm) .............................1
WASHER ..............................................................................................4
REQ’D
HYDRAULIC PUMP (PARKER-HANNIFIN)
(Use on power steering models)
1
2
3
4
5
6
7
8
9
C33579
C32955
C33110
NSS
NSS
NSS
NSS
NSS
C33111
126-13
PUMP - hydraulic 3/4” shaft......................................................................1
KIT - seal..................................................................................................1
SEAL - shaft ..........................................................................................1
SEAL - “V” (“V” side towards cover) ......................................................1
GASKET ...............................................................................................1
SHIELD - heat .......................................................................................1
PLATE - wear (bronze side towards gears) ...........................................1
PLATE - thrust (bronze side towards gears) ..........................................1
“0” RING................................................................................................2
KEY - 3/16” x 5/16” woodruff (pump shaft) .............................................1
INDEX
INDEX
HYDRAULIC DRIVE MOTOR
MODEL 3016PS, 3018PS, 3020PS, 4016; 4016PS, 4018PS, 4020PS COMPACT TRACTORS
INDEX
REF.
1
1
2
3
4
5
5
6
7
7
8
9
10
11
12
13
14
15
16
1.7
18
PART NO
DESCRIPTION
C33234
C30939
28-668
C31327
C31309
C31310
C31311
C31312
C31313
C31314
C31315
C31316
C31317
C31318
C31319
C31320
C31321
C31322
C31323
NSS
NSS
NSS
NSS
NSS
MOTOR - hydraulic (4016, 4016PS, 4018PS, 4020PS)............................1
MOTOR - hydraulic (3016PS, 3018PS, 3020PS) .....................................1
BOLT - 3/8”-24x4-1/4”(3016PS,3018PS, 3020PS) ..................................7
BOLT - 3/8” -24 x 4-5/8” (4016, 4016PS, 4018PS, 4020PS).....................7
COVER-end .............................................................................................1
COMMUTATOR AND RING SET .............................................................1
MANIFOLD ..............................................................................................1
ROTOR ASSEMBLY (3016PS, 3018PS, 3020PS) ...................................1
ROTOR ASSEMBLY (4016, 4016PS, 4018PS, 4020PS) .........................1
PLATE - wear...........................................................................................1
LINK – drive (3016PS, 3018PS, 3020PS) ................................................1
UNK – drive (4016, 4016PS, 4018PS, 4020PS) .......................................1
BEARING - thrust.....................................................................................1
SHAFT – coupling ....................................................................................7
WASHER - trust .......................................................................................2
BEARING - thrust.....................................................................................1
HOUSING - drive end...............................................................................1
BEARING - outer......................................................................................1
KIT - seal..................................................................................................1
SEAL - commutator ring ...........................................................................1
SEAL - ring...............................................................................................5
SEAL - ring...............................................................................................1
WASHER - backup...................................................................................1
SEAL - dirt (not used)...............................................................................1
REQ’D
PUMP MOUNTING COMPONENTS
1
2
3
4
4
5
5
6
7
8
9
C32437
131-911
C32199
C31964
C33553
C33506
C 33552
113-208
131-1352
113-103
192-20
MOUNT - rubber ......................................................................................1
NUT - 5/16” - 18 flangelock ......................................................................2
SCREW - Set 5/16” - 18 x 5/16” socket (use loctite) .................................2
ADAPTER - drive (4016) ..........................................................................1
ADAPTER - drive (3016PS, 3018PS, 3020PS, 4016PS, 4018PS, 4020PS) .....1
PLATE - pump torque arm (4016) ............................................................1
PLATE - torque arm (3016PS, 3018PS, 3020PS, 4016PS, 4018PS, 4020PS) ...........1
BOLT - 3/8”-16 x 1-1/4” hex......................................................................2
NUT - 3/8” - 16 flange lock .......................................................................2
BOLT - 5/16” – 18 x 1” hex .......................................................................4
LOCKWASHER - 5/16” ............................................................................4
INDEX
HYDRAULIC CONTROL VALVE
INDEX
HYDRAULIC CONTROL VALVE
REF.
PART NO.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
C33473
C29956
C28217
C28856
C29951
211-208
C21507
C17433
C17435
129-531
C26668
C28707
C28706
C28705
NSS
211-5
C17438
C28708
C17444
169-114
221-841
C21506
C26665
C26664
C26666
C26663
C34555
C29950
C29958
211-7
C17443
C30002
VALVE - control, two spool.......................................................................1
CAP - end ............................................................................................2
“0” RING - end cap...........................................................................1
SEAL - spool ........................................................................................4
SPRING - centering .............................................................................2
BALL - steel 5/16” (7.94 mm) ...............................................................1
SPRING - relief ....................................................................................2
SCREW - relief adjust ..........................................................................1
GASKET - relief adjust cap ..................................................................1
CAP - adjust screw...............................................................................2
DETENT - spool...................................................................................1
SPACER - detent .................................................................................1
SPRING - detent return........................................................................1
WASHER - return.................................................................................2
SPRING - relief (use C2151 1 relief kit)................................................1
BALL - steel 3/16” (4.76 mm) ...............................................................2
COVER - detent ...................................................................................1
SCREW - detent ..................................................................................2
SPRING - detent ..................................................................................4
SCREW - cover....................................................................................4
PLUG - pipe .........................................................................................1
RETAINER – ball seat..........................................................................1
SCREW - adjust, relief .........................................................................1
GASKET - adjust cap ...........................................................................1
CAP - adjust screw...............................................................................1
SEAT - relief ball ..................................................................................1
NUT - lock............................................................................................1
WASHER - spring retaining..................................................................2
DETENT - spool...................................................................................1
BALL - steel 1/4” (6.35 mm) .................................................................2
SCREW - detent ..................................................................................2
KIT - seal..................................................................................................1
REQ’D
INDEX
SPEED CONTROL
INDEX
REF.
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
SPEED CONTROL
PART NO.
DESCRIPTION
C28237
C46481
C29636
C37250
C10482
NSS
C31670
129-122
C19025
195-521
132-320
138-2072
C30827
113-14
192-19
C31678
192-20
C32362
C31674
C29653
C44384 *
113-3 *
192-19 *
129-101 *
C37254 *
C37255 *
C37198 *
C44029 *
187-1328 *
KNOB - speed control (Hard Plastic)......................................................... 1
GRIP - speed control (Soft Rubber) .......................................................... 1
BUSHING - lever ....................................................................................... 1
LEVER - speed control .............................................................................. 1
SPRING - compression ............................................................................. 1
WASHER - nylon (use C44383) ................................................................ 1
ROD - control............................................................................................. 1
NUT - 5/16” N.F. hex, zinc plated .............................................................. 1
JOINT-ball ................................................................................................. 1
WASHER - 5/16” ....................................................................................... 1
PIN - cotter 3/32” x 3/4” ............................................................................. 1
PIN - roll 1/8” x 1-3/4” ................................................................................ 1
SPRING - locator....................................................................................... 2
BOLT - 114” 20 x 2”................................................................................... 2
LOCKWASHER - 1/4”................................................................................ 2
CARRIER - locator .................................................................................... 1
LOCKWASHER - 5/16”.............................................................................. 1
LOCATOR - half ........................................................................................ 2
ACCUATOR - switch ................................................................................. 1
SPACER - tube.......................................................................................... 2
STRAP - retainer ....................................................................................... 1
BOLT - 1/4” - 20 x 3/4”............................................................................... 2
LOCKWASHER - 1/4”................................................................................ 2
NUT - 1/4” -20............................................................................................ 2
SUPPORT - locator ................................................................................... 1
CARRIER - locator .................................................................................... 1
CAM - switch ............................................................................................. 1
RETAINER - switch ................................................................................... 1
SCREW - #8 - 18 x 3/8”............................................................................. 1
REQ’D
Use PIN and after:
3018PS - 14181900
4020PS - 14184000
DRAWBAR AND TOW HITCH
1
2
3
C13360
192-23
113-424
DRAWBAR ................................................................................................ 1
LOCKWASHER - 1/2”................................................................................ 2
BOLT - 1/2” x 1” N.C. hex.......................................................................... 2
INDEX
HYDRAULIC LIFT
INDEX
REF.
1
2
3
4
5
5
6
7
8
9
10
11
11
12
13
14
15
16
17
18
19
20
21
22
23
25
26
27
28
28
29
30
HYDRAULIC LIFT
PART NO.
DESCRIPTION
C32259
219-17
C29693
132-310
NSS *
C44743 **
C17249
C17250
192-20
C33136
C33956
C29045
C46481
C29836
132-320
195-533
NSS
C31681
195-521
C31670
129-122
C19025
218-5134 * *
131-938
113-208
C26188
218-1093
218-5056 *
NSS *
C44742 * *
C26493
C30054
C13106
SHAFT ASSEMBLY - lift............................................................................ 1
FITTING - lubrication ................................................................................. 1
PIN - cylinder to lever, clevis ..................................................................... 1
PIN - cotter 1/8” x 1” .................................................................................. 5
HOSE - long (shown) (use C44743, 218-5134)......................................... 1
HOSE - long .............................................................................................. 1
BRACKET - mounting, top......................................................................... 2
BRACKET - mounting, bottom................................................................... 2
LOCKWASHER - 5/16”.............................................................................. 1
BRACKET - cylinder .................................................................................. 1
LEVER - lift control .................................................................................... 1
KNOB - control lever (Hard Plastic)........................................................... 1
GRIP – control lever (Soft Rubber)............................................................ 1
BUSHING - lift lever................................................................................... 1
PIN - cotter 3/32” x 3/4” ............................................................................. 1
WASHER - 1/2” ......................................................................................... 1
WASHER - nylon (use C44383) ................................................................ 1
SPRING - control lever .............................................................................. 1
WASHER - 5/16” ....................................................................................... 1
ROD - control............................................................................................. 1
NUT - 5/16” N.F. hex ................................................................................. 1
BALLJOINT ............................................................................................... 1
FITTING - 1/2” - 20 x 450 .......................................................................... 2
NUT - lock 3/8” N.C. hex ........................................................................... 8
BOLT - 3/8” - 16 x 1-1/4” .......................................................................... 4
PIN - cylinder base .................................................................................... 1
FITTING - hydraulic 45° elbow .................................................................. 1
FITTING - valve (includes 218-5004 “0” ring)............................................ 2
HOSE - short (shown) (use C44742, 218-5134) ....................................... 1
HOSE - short ............................................................................................. 1
CYLINDER - lift.......................................................................................... 1
KIT - seal ............................................................................................... 1
COVER - lubrication fitting......................................................................... 1
REQ’D
*Use before PIN:
3018PS - 14181900
4020PS -14184000
All others before PIN
INDEX
STARTER
INDEX
STARTER
REF.
PART NO.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
C32448
192-20
C32449
C20248
C32312
C32313
C32314
C32315
C32316
C32317
C32318
C32319
C32320
C31618
BOLT-thru5/16”-18x3-1/2” ........................................................................2
LOCKWASHER-5/16” ..............................................................................2
WASHER - special (outside mounting bolt) ..............................................1
WASHER - 5/16” (inside mounting bolt) ...................................................1
STARTER ASSEMBLY ............................................................................1
KIT-hardware ........................................................................................1
KIT - solenoid (includes plunger) ...........................................................1
KIT - bushing (includes rear cap)...........................................................1
HOLDER - brush (includes negative brush)...........................................1
KIT-brush ..............................................................................................1
KIT-shift lever ........................................................................................1
CLUTCH - starter (includes gear) ..........................................................1
SEAL-dust.............................................................................................1
COVER - terminal ....................................................................................1
REQ’D
INDEX
AFTER PIN #’s
ELECTRICAL SYSTEM
3018PS BEFORE PIN 14181900
4020PS BEFORE PIN 14184000
3016, 3020PS, 4016, 4016PS, 4018PS - ALL
INDEX
ELECTRICAL SYSTEM
(3018PS - use before PIN 14181900)
(4020PS - use before PIN 14184000)
(3016PS, 3020PS, 4016, 4016PS, 4018PS - All)
REF.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
AFTER PIN #’s
PART NO.
DESCRIPTION
C31941
C31986
C31947
C30260
C25338
C24460
C30262
C30263
C31948
C30279
C25486
C31952
C31950
C24813
C24809
C31044
C14537
C31617
C32178
C43044
C31619
C31937
C30530
C32407
C42929
C41010
C30275
C33198
C32312
C24956
C32461
C32458
C32454
C32296
C32299
C32307
C32294
C34181
HARNESS - wire ...................................................................................... 1
KIT - diode, 6 amps, 15 volt................................................................... 1
KIT - fuse holder .................................................................................... 1
FUSE - 30 amp :................................................................................ 1
CONNECTOR - seat harness, male...................................................... 1
CONNECTOR - ignition switch.............................................................. 1
BULB - indicator lights (not included with harness) ............................... 3
SOCKET - bulb...................................................................................... 3
CONNECTOR - PTO............................................................................. 1
CONNECTOR - switch .......................................................................... 3
CONNECTOR - sensor ......................................................................... 1
CONNECTOR - PTO switch, 2 terminal ................................................ 1
CONNECTOR - PTO switch, 3 terminal ................................................ 1
CONNECTOR - seat harness, female....................................................... 1
CABLE - battery negative to ground.......................................................... 1
HARNESS - wire, seat switch (includes Ref. 9 and 13) ............................ 1
CONNECTOR - headlights........................................................................ 1
SENSOR - voltage (includes connector) ................................................... 1
HEADLIGHT - 12 volt (repairs page 69).................................................... 2
SWITCH - headlight................................................................................... 1
CAP - PTO switch...................................................................................... 1
SWITCH - PTO.......................................................................................... 1
SWITCH - ignition (includes key and mounting hardware)........................ 1
KEY - ignition......................................................................................... 2
HOURMETER ........................................................................................... 1
BATTERY - 12 volt, 300 CCA.................................................................... 1
SWITCH - inter-lock................................................................................... 3
CLUTCH - PTO (see page 25 for repairs) ................................................. 1
STARTER AND SOLENOID - (see page 63 for repairs) ........................... 1
STATOR - charging ................................................................................... 1
RECTIFIER - voltage, 12 volt .................................................................... 1
KIT - terminal connector ........................................................................ 2
SPARK PLUG - includes gasket................................................................ 2
COIL - ignition 12 volt ................................................................................ 1
CABLE KIT - spark plug 18-1/2” ................................................................ 2
CONDENSER............................................................................................ 1
CONTROL - ignition .................................................................................. 1
WIRE - lights.............................................................................................. 1
REQ’D
INDEX
ELECTRICAL SYSTEM
3018PS AFTER SN 14181900
4020PS AFTER SN 14184000
BEFORE PIN #’s
INDEX
ELECTRICAL SYSTEM
REF.
PART NO.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
C43227
C24809
C43228
C14537
C37165
C31617
C32178
C43044
C41010
C30530
C24460
C45917
C37298
C30275
C37399
C30279
C32312
C32461
C32296
C32307
C42118
C31947
C30260
C30262
C30263
C42117
C25486
C37398
C42115
C42116
C31937
C31986
C33198
C31948
HARNESS - wire, main.............................................................................. 1
CABLE - battery negative to ground.......................................................... 1
HARNESS - wire, seat switch, PTO and taillights ..................................... 1
CONNECTOR - headlights........................................................................ 1
TAILLIGHT - rear (use 193-1000 nut for mounting) .................................. 2
SENSOR - voltage..................................................................................... 1
HEADLIGHT - 12 volt (page 69 for service) .............................................. 2
SWITCH - headlights................................................................................. 1
BATTERY - 12 volt 300 CCA..................................................................... 1
SWITCH - ignition...................................................................................... 1
CONNECTOR - ignition switch............................................................... 1
HOURMETER ........................................................................................... 1
SWITCH - seat (black)............................................................................... 2
SWITCH - micro (at travel lever) ............................................................... 3
SWITCH - micro (at PTO).......................................................................... 2
CONNECTOR - micro switch .................................................................... 5
STARTER AND SOLENOID - 12 volt (see page 63 for service) ............... 1
RECTIFIER - voltage, 12 volts .................................................................. 1
COIL - ignition, 12 volt ............................................................................... 1
CONDENSER - 12 volt.............................................................................. 1
CONNECTOR - single female, taillight...................................................... 1
KIT - fuse holder ........................................................................................ 1
FUSE - 30 amp....................................................................................... 1
BULB - indicator ........................................................................................ 3
SOCKET - bulb.......................................................................................... 3
CONNECTOR - six wire, harness, female................................................. 1
CONNECTOR - three wire, senor ............................................................. 1
CONNECTOR - seat switch ...................................................................... 2
CONNECTOR - six wire, seat harness, male............................................ 1
CONNECTOR - harness, taillight, male .................................................... 1
SWITCH - PTO.......................................................................................... 1
KIT - diode ................................................................................................. 1
CLUTCH - PTO, electric (see page 25 for repairs).................................... 1
CONNECTOR - PTO................................................................................. 1
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
REQ’D
INDEX
INDEX
ELECTRICAL SYSTEM HARDWARE
HEADLIGHT ASSEMBLY AND REAR REFLECTOR
INDEX
REF.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
24
25
25
26
27
28
29
30
31
31
32
33
34
ELECTRICAL SYSTEM HARDWARE
PART NO.
121-21
182-525
C32460
C32453
C32456
C32455
187-1036
182-12
192-13
129-13
C22947
C32301
C32300
193-6
C32459
C32295
C31619
C33475
C33475
C24069
C32396
C32397
C19521
111-132
113-3 *
129-102
129-101 *
C32407
C23012
129-36
129-27
193-6
C42358
C31977
195-518 *
C32454
C32299
DESCRIPTION
REQ’D
BOLT - 1/4” - 20 x 1/2” flange lock ........................................................................ 1
BOLT - #10 - 32 x 3/8” ........................................................................................... 2
LOCKWASHER - #10 internal tooth ..................................................................... 12
CLIP - wire ............................................................................................................. 1
BOLT - 1/4” - 20 x 1”.............................................................................................. 2
CLIP - wire ............................................................................................................. 2
SCREW - 1/4” - 20 x 1”.......................................................................................... 1
SCREW - #4 - 40 x 1-1/8”...................................................................................... 2
LOCKWASHER - #4 .............................................................................................. 2
NUT - #4 - 40 ......................................................................................................... 2
TIE - wire ............................................................................................................ UAR
NUT - M5 metric (negative terminal) ..................................................................... 1
NUT - M4 metric (positive terminal)....................................................................... 1
LOCKWASHER - #10 ............................................................................................ 3
SCREW - #10 - 32 x 1” self lock ............................................................................ 3
INSULATOR - ignition module............................................................................... 1
CAP - PTO switch.................................................................................................. 1
RETAINER - battery .............................................................................................. 1
RETAINER - battery .............................................................................................. 1
COVER - battery positive terminal......................................................................... 1
NUT - switch .......................................................................................................... 1
CAP - nut ............................................................................................................... 1
CLIP - wire ............................................................................................................. 3
BOLT - 5/16” - 18 x 3/4” carriage........................................................................... 2
BOLT - 1/4” - 20 x 3/4” (shown) ............................................................................. 2
NUT - 5/16” - 18.................................................................................................. UAR
NUT - 1/4” - 20....................................................................................................... 2
KEY - ignition ......................................................................................................... 1
LOCKWASHER (early production) ........................................................................ 1
NUT - #8 - 36 ......................................................................................................... 2
NUT - # 10NF ........................................................................................................ 4
LOCKWASHER - #10 ............................................................................................ 2
CLIP - wire (at tail light) ......................................................................................... 2
CLIP - wire (at hydraulic PTO)............................................................................... 1
WASHER - 1/4”...................................................................................................... 2
SPARK PLUG ........................................................................................................ 2
CABLE KIT - spark plug......................................................................................... 2
* Use PIN and after:
3018PS - 14181900
4020PS - 14184000
HEADLIGHT ASSEMBLY AND REAR RELECTOR
1
2
3
4
5
6
7
C29637
187-1328
C32178
NSS
C28932
C14304
C22573
C30942
RETAINER - headlight........................................................................................... 4
SCREW - No. 8 x 3/8”............................................................................................ 4
HEADLIGHT ASSEMBLY...................................................................................... 2
RECEPTACLE - headlight (order C32178) ........................................................ 1
BULB - headlight................................................................................................. 1
GASKET - headlight ........................................................................................... 2
LENS - headlight................................................................................................. 1
REFLECTOR - red, rear fender ............................................................................. 2
INDEX
DECALS
INDEX
DECALS
REF.
PART NO.
DESCRIPTION
1
1
2
3
4
5
6
6
7
7
8
8
9
10
11
12
13
13
14
14
15
15
16
17
18
19
20
21
C33478
C33479
C33588
321-4767
C33589
C33590
C33476
C33477
C32007
C32008
C33484
C33485
NSS
C30539
C30274
C32093
C33486
C33487
C33480
C33481
C33482
C33483
C34184 *
C44340 *
C44341 *
C37197 *
C37274 *
C37275 *
DECAL - “3018” Power Steering” hood L.H. (shown)................................1
DECAL - “3018” Power Steering” hood R.H .............................................1
DECAL - fuel gauge .................................................................................1
DECAL - hydraulic reservoir .....................................................................1
DECAL - shift range .................................................................................1
DECAL - brake .........................................................................................1
DECAL - “3016 Power Steering” hood L.H. (shown).................................1
DECAL - “3016 Power Steering” hood R.H...............................................1
DECAL - “4016” hood L.H. (shown)..........................................................1
DECAL - “4016” hood R.H........................................................................1
DECAL - “4018” Power Steering” hood L.H. (shown)................................1
DECAL - Caution (use C44340)
MEDALLION ............................................................................................1
LENS - display .........................................................................................1
DECAL - seat back “Ingersoll” ..................................................................1
DECAL - flag ............................................................................................1
DECAL - “WARNING” ..............................................................................1
DECAL - ”ATTENTION” ...........................................................................1
DECAL - steering wheel ...........................................................................1
DECAL - shift range .................................................................................1
DECAL - PTO (if equipped) ......................................................................1
REQ’D
* Use PIN and after:
301 8PS - 14181900
4020PS - 14184000

8-3121 - Paw Paw Rentals

Transcription

Similar documents

8-3200 - Rottman Sales