docProduct Catalogue - Chain and Drives
download 
Report Transcription
Product Catalogue - Chain and Drives
Product Catalogue ISO 9001 Licence No QEC 11027 SAI Global INDEX Product Page Deep Groove Ball Bearings- Metric 1-3 Deep Groove Ball Bearings- Imperial 4 Deep Groove Ball Bearings- Special Bore 5 Deep Groove Ball Bearings- Double Row 5-6 Deep Groove Ball Bearings- Self Aligning 6 Thrust Bearings- Three Piece Ball 7 Taper Roller Bearings- Metric 8-10 Taper Roller Bearings- Imperial 11 Spherical Roller Bearings 11-12 Spherical Plain Bearings 13-15 Rod End 15-18 Water Pump Bearings 18 Transmission Bearings 19-25 Transmission Housings 26-32 Adaptor Sleeves 33 Lock Nuts & Washers 34 Unground Bearings 34 Agricultural Bearings 35-36 DU Bushes 36-37 Circlips 38-39 SPA Taper Lock Pulleys 40 Taper Lock Bushes 40 Roller Chain 41 Automotive Tensioners & Idlers 42 Automotive Engine Pulleys 43 Automotive Hubs 43 Seals & O'Rings 43 Tools 44-45 Reference Tables 46-50 Cross Over Charts 51-52 Deep Groove Ball Bearings - Metric Miniature Bore d 2 3 3 4 5 5 6 6 7 7 8 8 8 9 9 9 D 7 10 7 12 14 16 17 19 19 22 22 24 16 24 26 17 Bearing widths (B) bases on sealed bearings Basic Load Rating(KN) Dynamic Static Cr Cor B r (min.) 3.5 0.15 0.39 0.13 4 0.15 0.64 0.23 3 0.15 0.31 0.11 4 0.20 0.97 0.36 5 0.20 1.30 0.49 5 0.30 1.75 0.67 6 0.30 1.95 0.74 6 0.30 2.60 1.05 6 0.30 2.60 1.05 7 0.30 3.30 1.35 7 0.30 3.30 1.35 8 0.30 3.35 1.40 4 0.20 1.60 0.71 7 0.30 3.35 1.40 8 0.60 4.55 2.00 5 0.20 1.35 0.66 Limiting Speed Grease Oil r/min r/min 76000 79000 52000 63000 66000 79000 53000 63000 50000 60000 40000 49000 43000 51000 35000 43000 40000 47000 31000 37000 34000 41000 28000 35000 42000 50000 33000 40000 27000 33000 39000 46000 Bearing No. 602 623 683 604 605 625 606 626 607 627 608 628 688 609 629 689 D 26 28 32 35 42 47 55 62 68 75 80 90 95 100 110 115 125 130 140 145 150 Stainless Steel Available upto 6010 Basic Load Rating(KN) Dynamic Static Cr Cor B r (min.) 8 0.30 4.55 1.95 8 0.30 5.10 2.40 9 0.30 5.60 2.85 10 0.30 6.00 3.25 12 0.60 9.40 5.05 12 0.60 10.10 5.85 13 1.00 13.20 8.25 14 1.00 15.90 10.30 15 1.00 16.70 11.50 15.10 16 1.00 21.00 16 1.10 21.00 16.60 18 1.10 28.30 21.20 18 1.10 29.40 23.20 18 1.10 30.50 25.20 20 1.10 38.10 30.90 20 1.10 39.60 33.50 22 1.10 47.60 39.80 22 1.10 49.50 43.10 24 1.50 58.20 49.70 24 1.50 60.40 53.90 24 1.50 60.20 54.20 Limiting Speed Grease Oil r/min r/min 29000 34000 26000 30000 22000 26000 20000 24000 18000 21000 15000 18000 13000 15000 12000 14000 10000 12000 9200 11000 8400 9800 7700 9000 7000 8300 6500 7700 6100 7100 5700 6700 5300 6200 5000 5900 4700 5600 4500 5300 4200 5000 Bearing No. 6000 6001 6002 6003 6004 6005 6006 6007 6008 6009 6010 6011 6012 6013 6014 6015 6016 6017 6018 6019 6020 6000 Series Bore 10 12 15 17 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 d Page 1 Deep Groove Ball Bearings - Metric 6200 Series Bore d 10 12 15 17 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 D 30 32 35 40 47 52 62 72 80 85 90 100 110 120 125 130 140 150 160 170 180 Stainless Steel Available upto 6211, use Prefix 'SS" Basic Load Rating(KN) Limiting Speed Dynamic Static Grease Oil Cr Cor r/min r/min B r (min.) 9 0.60 5.10 2.40 24000 29000 10 0.60 6.80 3.05 22000 27000 11 0.60 7.65 3.75 20000 24000 12 0.60 9.55 4.80 17000 21000 14 1.00 12.80 6.65 15000 17000 15 1.00 14.00 7.85 13000 15000 16 1.00 19.50 11.30 11000 13000 17 1.10 25.70 15.40 9200 11000 18 1.10 29.10 17.80 8300 10000 19 1.10 32.70 20.30 7700 9200 20 1.10 35.10 23.30 7100 8500 21 1.50 43.40 29.40 6300 7600 22 1.50 52.40 36.20 5700 6900 23 1.50 57.20 40.10 5400 6400 24 1.50 62.20 44.10 5100 6100 25 1.50 67.40 48.30 4800 5800 26 2.00 72.70 53.00 4500 5400 28 2.00 84.00 61.90 4200 5000 30 2.00 96.10 71.50 3900 4700 32 2.10 109.00 81.90 3700 4400 34 2.10 122.00 93.10 3500 4200 Bearing No. 6200 6201 6202 6203 6204 6205 6206 6207 6208 6209 6210 6211 6212 6213 6214 6215 6216 6217 6218 6219 6220 D 35 37 42 47 52 62 72 80 90 100 110 120 130 140 150 160 170 180 190 200 210 Stainless Steel Available upto 6308, use Prefix 'SS' Basic Load Rating(KN) Limiting Speed Dynamic Static Grease Oil Cr Cor r/min r/min B r (min.) 11 0.60 8.10 3.45 22000 27000 12 1.00 9.70 4.20 20000 25000 13 1.00 11.40 5.45 17000 20000 14 1.00 13.60 6.65 15000 18000 15 1.10 15.90 7.85 14000 17000 17 1.10 20.60 11.30 11000 13000 19 1.10 26.70 15.00 9600 12000 21 1.50 33.40 19.30 8500 10000 23 1.50 40.70 24.00 7700 9200 25 1.50 48.90 29.50 6800 8100 27 2.00 62.00 38.30 6100 7300 29 2.00 71.60 45.00 5600 6700 31 2.10 81.90 52.20 5200 6200 33 2.10 92.70 59.90 4800 5800 35 2.10 104.00 68.20 4500 5400 37 2.10 113.00 77.20 4200 5000 39 2.10 123.00 86.70 3900 4700 41 3.00 133.00 96.80 3700 4400 43 3.00 143.00 107.00 3500 4200 45 3.00 153.00 119.00 3300 4000 47 3.00 173.00 141.00 3000 3600 Bearing No. 6300 6301 6302 6303 6304 6305 6306 6307 6308 6309 6310 6311 6312 6313 6314 6315 6316 6317 6318 6319 6320 6300 Series Bore 10 12 15 17 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 d Page 2 Deep Groove Ball Bearings - Metric 6800 Series Bore d 10 12 15 17 20 25 30 35 40 45 50 55 60 D 19 21 24 26 32 37 42 47 52 58 65 72 78 Stainless Steel Available upto 6805 Basic Load Rating(KN) Dynamic Static Cr Cor B r (min.) 5 0.30 1.70 0.84 5 0.30 1.90 1.05 5 0.30 2.10 1.25 5 0.30 2.60 1.55 7 0.30 4.00 2.45 7 0.30 4.30 2.95 7 0.30 4.55 3.40 7 0.30 4.75 3.85 7 0.30 4.95 4.20 7 0.30 6.20 5.40 7 1.30 6.60 6.10 9 0.30 8.80 8.10 10 0.30 11.50 10.60 Limiting Speed Grease Oil r/min r/min 37000 43000 33000 39000 28000 33000 26000 30000 21000 25000 18000 21000 15000 18000 13000 16000 12000 14000 11000 13000 9600 11000 8700 10000 8000 9400 Bearing No. 6800 6801 6802 6803 6804 6805 6806 6807 6808 6809 6810 6811 6812 D 22 24 28 30 37 42 47 55 62 68 72 80 85 Stainless Steel Available upto 6905 Basic Load Rating(KN) Dynamic Static Cr Cor B r (min.) 6 0.30 2.70 1.25 6 0.30 2.90 1.45 7 0.30 4.30 2.25 7 0.30 4.60 2.55 9 0.30 6.35 3.70 9 0.30 7.00 4.55 9 0.30 7.25 5.00 10 0.60 10.90 7.75 12 0.60 13.70 9.95 12 0.60 14.10 10.90 12 0.60 14.50 11.70 13 1.00 16.60 14.10 13 1.00 20.20 17.30 Limiting Speed Grease Oil r/min r/min 34000 41000 31000 36000 26000 30000 23000 28000 19000 23000 16000 19000 14000 17000 12000 14000 11000 13000 9700 11000 9000 11000 8100 9600 7500 8900 Bearing No. 6900 6901 6902 6903 6904 6905 6906 6907 6908 6909 6910 6911 6912 D 30 32 35 40 47 52 62 Basic Load Rating(KN) Dynamic Static Cr Cor r (min.) 0.60 5.10 2.39 0.60 6.10 2.75 0.60 7.75 3.60 0.60 9.60 4.60 1.00 12.80 6.65 1.00 14.00 7.85 1.00 19.50 11.30 Limiting Speed Grease Oil r/min r/min 25000 30000 22000 26000 19000 23000 18000 21000 16000 18000 13000 15000 11000 13000 Bearing No. 62200 62201 62202 62203 62204 62205 62206 6900 Series Bore d 10 12 15 17 20 25 30 35 40 45 50 55 60 62200 Series Bore d 10 12 15 17 20 25 30 B 14 14 14 16 18 18 20 Page 3 Deep Groove Ball Bearings - Imperial EE/R Series Bore d 4.762 6.350 9.525 12.700 15.875 19.050 22.225 25.400 28.575 31.750 34.925 38.100 Please Note: Basic Load Rating(KN) Dynamic Static Cr Cor r (min.) 0.300 1.300 0.490 0.300 2.800 1.050 0.300 2.570 1.360 0.300 5.110 2.390 0.600 6.000 3.250 0.600 9.380 5.030 0.600 10.060 5.850 0.600 10.060 5.850 0.600 13.230 8.300 1.000 13.230 8.300 1.000 16.210 10.420 1.000 17.030 11.700 B1 D B 12.700 3.968 4.978 19.050 5.558 7.142 22.225 5.558 7.142 28.575 6.350 7.938 34.925 7.144 8.730 41.275 7.938 11.112 47.625 9.525 12.700 50.800 9.525 12.700 53.975 9.525 12.700 57.150 9.525 12.700 63.500 11.112 14.288 66.675 11.112 14.288 B dimension for Open Bearing B1 dimension for 2RS and ZZ bearings RLS Series Bore d 12.700 15.875 19.050 22.225 25.400 28.575 31.750 34.925 38.100 44.450 50.800 D 33.338 39.688 47.625 47.625 57.150 63.500 69.850 76.200 82.550 95.250 101.600 B 9.525 11.113 14.288 14.288 15.875 15.875 17.463 17.463 19.050 20.638 20.638 Basic Load Rating(KN) Dynamic Static Cr Cor r (min.) 0.800 6.250 2.800 0.800 9.750 4.900 1.600 13.100 6.800 1.600 14.200 7.850 1.600 18.200 9.850 1.600 19.800 11.500 1.600 19.900 11.900 1.600 21.300 13.600 2.400 29.700 18.200 2.400 35.100 23.300 2.400 39.100 26.500 Bearing No. RLS4 RLS5 RLS6 RLS7 RLS8 RLS9 RLS10 RLS11 RLS12 RLS14 RLS16 B 15.875 15.875 17.462 17.462 19.050 20.638 22.225 Basic Load Rating(KN) Dynamic Static Cr Cor r (min.) 1.600 9.650 4.500 1.600 11.800 5.650 1.600 14.100 6.950 2.400 18.950 9.550 2.400 21.000 11.500 2.400 27.200 15.300 2.400 30.600 17.500 Bearing No. RMS4 RMS5 RMS6 RMS7 RMS8 RMS9 RMS10 RMS Series Bore d 12.700 15.875 19.050 22.225 25.400 28.575 31.750 D 41.275 46.038 50.800 57.150 63.500 71.438 79.375 Page 4 Bearing No. EE1/R3 EE2/R4A EE3/R6 EE4/R8 EE5/R10 EE6/R12 EE8/R14 EE9/R16 EE10/R18 EE11/R20 EE12/R22 EE13/R24 Deep Groove Ball Bearings - Special Bore Sizes Bore d 15.875 15.875 15.875 12.700 12.700 16.000 19.050 19.050 19.050 25.400 D 42 35 40 32 35 35 42 40 47 52 B 12 11 12 10 11 11 12 12 14 15 Basic Load Rating(KN) Dynamic Static Cr Cor r (min.) 0.60 9.40 5.00 0.60 7.70 3.70 0.60 9.60 4.80 0.60 6.80 3.10 0.60 7.70 3.70 0.60 7.70 3.70 0.60 9.40 5.00 0.60 9.60 4.80 1.00 12.80 6.70 1.00 14.00 7.90 Bearing No. 6004 6202 6203 6201 6202 6202 6004 6203 6204 6205 Double Row Deep Groove Ball Bearings 5200 Series Bore d 10 12 15 17 20 25 30 35 40 45 50 55 60 70 75 D 30 32 35 40 47 52 62 72 80 85 90 100 110 125 130 B 14.30 15.90 15.90 17.50 20.60 20.60 23.80 27.00 30.20 30.20 30.20 33.30 36.50 39.70 41.30 Basic Load Rating(KN) Dynamic Static Cr Cor r (min.) 0.60 6.95 3.80 0.60 9.15 5.05 0.60 10.00 6.05 0.60 12.80 7.90 1.00 19.00 12.10 1.00 20.60 14.30 1.00 28.60 20.40 1.10 38.00 27.80 1.10 42.50 32.50 1.10 48.00 37.00 1.10 51.00 42.00 1.50 63.00 53.00 1.50 71.50 58.50 1.50 90.50 79.50 1.50 90.00 80.50 Page 5 Limiting Speed Grease Oil r/min r/min 14000 19000 13000 17000 11000 15000 9900 13000 8800 12000 7300 9800 6300 8400 5500 7400 4900 6600 4400 5900 4000 5300 3600 4900 3400 4500 2900 3900 2700 3600 Bearing No. 5200 5201 5202 5203 5204 5205 5206 5207 5208 5209 5210 5211 5212 5213 5215 Double Row Deep Groove Ball Bearings 5300 Series Bore d 15 17 20 25 30 35 40 45 50 D 42 47 52 62 72 80 90 100 110 B 19 22.2 22.2 25.4 30.2 34.9 36.5 39.7 44.4 Basic Load Rating(KN) Dynamic Static Cr Cor r (min.) 1.00 17.20 10.10 1.00 20.40 12.10 1.10 20.60 12.70 1.10 30.50 20.50 1.10 39.50 27.50 1.50 49.50 35.00 1.50 60.50 44.00 1.50 72.50 54.00 2.00 85.50 64.50 Limiting Speed Grease Oil r/min r/min 9900 13000 9000 12000 8000 11000 6700 8900 5700 7600 5000 6600 4400 5900 4000 5300 3600 4800 Bearing No. 5302 5303 5304 5305 5306 5307 5308 5309 5310 Self Aligning Deep Groove Ball Bearings 1200 Series Bore d 15 17 20 25 30 35 40 45 50 Bore d 15 17 20 25 30 35 40 45 50 55 60 Please Note: D 35 40 47 52 62 72 80 85 90 D 35 40 47 52 62 72 80 85 90 100 110 B 11 12 14 15 16 17 18 19 20 Basic Load Rating(KN) Dynamic Static Cr Cor r (min.) 0.60 7.45 1.75 0.60 7.90 2.00 1.00 9.90 2.60 1.00 12.10 3.30 1.00 15.60 4.65 1.10 15.80 5.10 1.10 19.20 6.50 1.10 21.80 7.35 1.10 22.70 8.10 Limiting Speed Grease Oil r/min r/min 18000 22000 16000 20000 14000 17000 12000 14000 9900 12000 8500 10000 7500 9200 7000 8500 6500 7900 Bearing No. 1202 1203 1204 1205 1206 1207 1208 1209 1210 B 14 16 18 18 20 23 23 23 23 25 28 Basic Load Rating(KN) Dynamic Static Cr Cor r (min.) 0.60 7.70 1.85 0.60 9.80 2.40 1.00 12.60 3.30 1.00 12.60 3.30 1.00 15.60 4.65 1.10 21.60 6.60 1.10 22.40 7.40 1.10 23.30 8.15 1.10 23.30 8.50 1.50 26.80 10.00 1.50 34.10 12.60 Limiting Speed Grease Oil r/min r/min 18000 22000 16000 20000 14000 17000 12000 15000 10000 12000 8500 10000 7600 9300 7000 8500 6500 7900 5800 7100 5300 6500 Bearing No. 2202 2203 2204 2205 2206 2207 2208 2209 2210 2211 2212 Use suffix "K" for Taper Bore. (eg. 1205K = Tapered Bore) Page 6 THREE PIECE BALL THRUST BEARING 51100 Series Bore d 10 12 15 17 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 D 24 26 28 30 35 42 47 52 60 65 70 78 85 90 95 100 105 110 120 B 9 9 9 9 10 11 11 12 13 14 14 16 17 18 18 19 19 19 22 Basic Load Rating(KN) Dynamic Static Cr Cor r (min.) 0.3 10 14 0.3 10.3 15.4 0.3 10.5 16.8 0.3 10.5 18.2 0.3 14.2 24.7 0.6 19.5 37.2 0.6 20.4 42.2 0.6 20.4 44.7 0.6 26.9 62.8 0.6 27.8 69.1 0.6 28.8 75.4 0.6 34.8 93.1 1 41.4 113 1 41.7 117 1 43 127 1 42.3 127 1 44.6 141 1 45.9 150 1 59.7 190 Limiting Speed Grease Oil r/min r/min 6500 10000 6500 10000 6100 9400 6100 9400 5100 7900 4400 6800 4300 6600 3900 60000 3400 5300 3200 5000 3100 4800 2800 4300 2600 4000 2400 3700 2300 3600 2200 3400 2100 3300 2100 3200 1900 2900 Bearing No. 51100 51101 51102 51103 51104 51105 51106 51107 51108 51109 51110 51111 51112 51113 51114 51115 51116 51117 51118 B 12 12 14 15 16 18 19 20 22 25 26 27 27 27 28 31 35 Basic Load Rating(KN) Dynamic Static Cr Cor r (min.) 0.6 16.6 24.8 0.6 17.2 27.3 0.6 22.3 37.7 0.6 27.8 50.4 0.6 29.3 58.2 1 39.2 78.2 1 46.9 98.3 1 47.7 105 1 48.5 111 1 69.4 159 1 73.4 179 1 74.8 189 1 73.6 189 1 77.4 209 1 78.5 218 1 92.3 251 1.1 117 326 Limiting Speed Grease Oil r/min r/min 4900 7500 4900 7500 3900 6000 3600 5500 3400 5200 2900 4500 2700 4200 2600 4000 2300 3600 2100 3200 1900 3000 1900 2900 1800 2800 1800 2700 1700 2600 1500 2300 1400 2100 Bearing No. 51202 51203 51204 51205 51206 51207 51208 51209 51210 51211 51212 51213 51214 51215 51216 51217 51218 51200 series Bore d 15 17 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 D 32 35 40 47 52 62 68 73 78 90 95 100 105 110 115 125 135 Page 7 TAPERED ROLLER BEARINGS - METRIC Principal Dimensions Bore d 15 15 17 17 17 20 20 20 20 20 25 25 25 25 25 25 25 30 30 30 30 30 30 30 35 35 35 35 35 35 35 40 40 40 40 40 40 40 40 45 45 45 45 45 45 45 45 45 D 35 42 40 47 47 47 47 52 52 52 47 52 52 52 62 62 62 55 62 62 62 72 72 72 62 72 72 72 80 80 80 68 75 80 80 80 90 90 90 75 80 85 85 85 100 100 100 100 T 11.8 14.3 13.3 15.3 20.3 15.3 19.3 16.3 16.3 22.3 15 16.3 19.3 22 18.3 18.3 25.3 17 17.3 21.3 25 20.8 20.8 28.8 18 18.3 24.3 28 22.8 22.8 32.8 19 26 19.8 24.8 32 25.3 25.3 35.3 20 26 20.8 24.8 32 27.3 27.3 31.8 38.3 B 11 13 12 14 19 14 18 15 16 21 15 15 18 22 17 17 24 17 16 20 25 19 19 27 18 17 23 28 21 21 31 19 26 18 23 32 23 23 33 20 26 19 23 32 25 25 29 36 (mm) C 10 11 11 12 16 12 15 13 12 18 11.5 13 16 18 13 15 20 13 14 17 19.5 14 16 23 14 15 19 22 15 18 25 14.5 20.5 16 19 25 17 20 27 15.5 20.5 16 19 24.5 18 22 20.5 30 Basic Load Ratings r1min 0.6 1 1 1 1 1 1 1.5 2 1.5 0.6 1 1 1 1.5 1.5 1.5 1 1 1 1 1.5 1.5 1.5 1 1.5 1.5 1.5 2 2 2 1 1.5 1.5 1.5 1.5 2 2 2 1 1.5 1.5 1.5 1.5 2 2 1.8 2 Page 8 r2min 0.6 1 1 1 1 1 1 1.5 2 1.5 0.6 1 1 1 1.5 1.5 1.5 1 1 1 1 1.5 1.5 1.5 1 1.5 1.5 1.5 1.5 1.5 1.5 1 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1 1.5 1.5 1.5 1.5 1.5 1.5 1.8 1.5 Cr 11.9 22.9 20.7 28.3 35.2 28.2 36.5 33.2 31.1 42.7 27 33.7 42 47.3 40.7 47 61.7 35.8 43.3 51.8 64.4 47.3 59 81.7 42.9 54.2 70.6 84.2 61.6 75.4 99.1 52.8 79.2 63 77 1.5 81 90 115 58 84 67 80 108 91 108 63 145 Cor 13.5 21.7 22.2 27.4 36.6 30.9 39.5 33.3 32 46.4 32.5 39.4 47 56 46 48.3 68.9 44 50.6 63.9 76.5 50 63.9 97.6 54 63.7 89.7 106 67 83.6 119 71 104 74.1 97 132 96 108 149 80 114 84 105 143 102 120 83 191 Bearing No. 30202 30302 30203 30303 32303 30204 32204 30304 30304C 32304 32005 30205 32205 33205 31305 30305 32305 32006 30206 32206 33206 31206 30306 32306 32007 30207 32207 33207 31207 30307 32307 32008 33108 30208 32208 33208 31308 30308 32308 32009 33109 30209 32209 33209 31309 30309 27709 32309 TAPERED ROLLER BEARINGS - METRIC Principal Dimensions Bore d 50 50 50 50 50 50 50 50 55 55 55 55 55 55 55 55 60 60 60 60 60 60 60 60 65 65 65 65 65 65 65 65 70 70 70 70 70 70 70 70 75 75 75 75 75 75 75 75 75 D 80 85 90 90 90 110 110 110 90 95 100 100 100 120 120 120 95 100 110 110 110 130 130 130 100 110 120 120 120 140 140 140 110 120 125 125 125 150 150 150 115 125 130 130 130 135 160 160 160 T 20 26 21.8 24.8 32 29.3 29.3 42.3 23 30 22.8 26.8 35 31.5 31.5 45.5 23 30 23.8 29.8 38 33.5 33.5 48.5 23 34 24.8 32.8 41 36 36 51 25 37 26.3 33.3 41 38 38 54 25 37 27.3 33.3 41 44.5 40 40 58 B 20 26 20 23 32 27 27 40 23 30 21 25 35 29 29 43 23 30 22 28 38 31 31 46 23 34 23 31 41 33 33 48 25 37 24 31 41 35 35 51 25 37 25 31 41 45 37 37 55 (mm) C 15.5 20 17 19 24.5 19 23 33 17.5 23 18 21 27 21 25 35 17.5 23 19 24 29 22 26 37 17.5 26.5 20 27 32 23 28 39 19 29 21 27 32 25 30 42 19 29 22 27 31 36.5 26 31 45 Basic Load Ratings r1min 1 1.5 1.5 1.5 1.5 2.5 2.5 2.5 1.5 1.5 2 2 2 2.5 2.5 2.5 1.5 1.5 2 2 2 3 3 3 1.5 1.5 2 2 2 3 3 3 1.5 2 2 2 2 3 3 3 1.5 2 2 2 2 2.5 3 3 3 Page 9 r2min 1 1.5 1.5 1.5 1.5 2 2 2 1.5 1.5 1.5 1.5 1.5 2 2 2 1.5 1.5 1.5 1.5 1.5 2.5 2.5 2.5 1.5 1.5 1.5 1.5 1.5 2.5 2.5 2.5 1.5 1.5 1.5 1.5 1.5 2.5 2.5 2.5 1.5 1.5 1.5 1.5 1.5 2.5 2.5 2.5 2.5 Cr 60 70 76 76 114 106 130 177 80 110 90 108 138 130 153 203 82 117 103 132 168 145 170 226 84 142 120 160 194 165 195 259 101 172 132 168 201 218 187 298 106 176 137 169 209 228 209 250 346 Cor 88 122 97 97 160 120 159 239 116 156 116 144 190 158 190 274 122 170 132 181 250 176 211 306 127 208 154 224 270 202 244 353 153 250 174 238 285 274 220 413 163 265 186 244 300 287 245 318 488 Bearing No. 32010 33110 30210 32210 33210 31310 30310 32310 32011 33111 30211 32211 33211 31311 30311 32311 32012 33112 30212 32212 33212 31312 30312 32312 32013 33113 30213 32213 33213 31313 30313 32313 32014 33114 30214 32214 33214 31314 30314 32314 32015 33115 30215 32215 33215 30615 31315 30315 32315 TAPERED ROLLER BEARINGS - METRIC Principal Dimensions Bore d 80 80 80 80 80 80 80 80 80 85 85 85 85 85 85 85 85 90 90 90 90 90 90 90 D 125 130 140 140 140 140 170 170 170 130 140 150 150 150 180 180 180 140 150 160 160 190 190 190 T 29 37 28.3 35.3 45 46 42.5 42.5 61.5 29 41 30.5 38.5 49 44.5 44.5 63.5 32 45 32.5 42.5 46.5 46.5 67.5 B 29 37 26 33 45 46 39 39 58 29 41 28 36 49 41 41 60 32 45 30 40 43 43 64 (mm) C 22 29 22 28 36.5 35 27 33 48 22 32 24 30 37 28 34 49 24 35 26 34 30 36 53 Basic Load Ratings r1min 1.5 2 2.5 2.5 2.5 2.5 3 3 3 1.5 2.5 2.5 2.5 2.5 4 4 4 2 2.5 2.5 2.5 4 4 4 r2min 1.5 1.5 2 2 2 2 2.5 2.5 2.5 1.5 2 2 2 2 3 3 3 1.5 2 2 2 3 3 3 Cr 138 179 160 197 246 251 224 278 387 140 220 180 226 286 242 304 421 168 251 199 269 264 341 477 Cor 216 280 213 280 366 375 265 356 549 224 340 242 325 430 285 392 599 270 390 270 396 315 341 477 NOTES: SUFFIXES: A C D DX g HL j F F2 h Changed internal design from standard Medium contact angles (about 17~24 deg.) Increased contact angles (about 24~32 deg.) Inner ring width and mounting width differ from brgs with contact angle D Bearing made of carburized steel Special heat treatment for long life Designs adapted to ISO standards Changed bore diameter from standard Changed outer diameter from standard Changed width from standard Page 10 Bearing No. 32016 33116 30216 32216 30616 33216 31316 30316 32316 32017 33117 30217 32217 33217 31317 30317 32317 32018 33118 30218 32218 31318 30318 32318 TAPERED ROLLER BEARINGS - IMPERIAL Principal Dimensions Bore d 17.462 19.050 21.430 21.986 21.986 25.400 26.988 29.000 31.750 31.750 34.925 35.000 34.988 38.000 40.988 41.275 41.275 41.275 45.242 50.000 D 39.878 45.237 50.005 45.237 45.974 50.292 50.292 50.292 59.131 62.000 65.088 59.131 59.974 63.000 67.975 73.025 73.431 73.431 73.431 82.000 T 13.843 15.494 17.526 15.494 15.494 14.224 14.224 14.224 15.875 18.161 18.034 15.875 15.875 17.000 17.500 16.667 19.558 21.430 19.558 21.500 B 14.605 16.637 18.288 16.637 16.637 14.732 14.732 14.732 16.764 19.050 18.288 16.764 16.764 17.000 18.000 17.462 19.812 19.812 19.812 21.500 (mm) C 10.668 12.065 13.970 12.065 12.065 10.668 10.668 10.668 11.811 14.288 13.970 11.938 11.938 13.500 13.500 12.700 14.732 16.604 15.748 17.000 Basic Load Ratings r1min 1.30 1.30 1.30 1.30 1.30 1.30 3.50 3.50 --------------3.50 3.50 3.50 3.50 3.00 r2min 1.30 1.30 1.30 1.30 1.30 1.30 1.30 1.30 1.30 1.30 1.30 1.30 1.30 1.30 1.50 1.50 0.80 0.80 0.80 0.50 Cr 23.40 29.90 37.00 29.60 29.60 28.50 28.50 27.70 34.50 46.50 46.50 34.00 34.00 38.50 46.00 46.00 56.00 56.00 54.00 69.50 Cor 23.00 30.50 37.50 34.00 34.00 34.00 34.00 35.50 41.00 54.00 56.00 46.00 46.00 52.50 62.50 55.50 69.50 69.50 76.00 94.00 SPHERICAL ROLLER BEARINGS Load Rating(KN) Bore d 20 30 35 40 40 45 45 50 50 D 52 62 72 80 90 85 100 90 110 B 18 20 23 23 33 23 36 23 40 Dynamic Cr 49 64 86,5 96,5 150 102 183 104 220 Static Cor 44 60 85 90 140 98 183 108 224 Page 11 Limiting Speed Grease Oil r/min r/min 13000 17000 10000 14000 9000 12000 8000 11000 6000 8000 7500 10000 5300 7000 7000 9500 4800 6300 Bearing No. 22205 22206 22207 22208 22308 22209 22309 22210 22310 Bearing No. LM11749/10 LM11949/10 M12649/10 LM12749/10 LM12749/11 L44643/10 L44649/10 L45449/10 LM67048/10 15123/245 LM48548/10 L68149/10 L68149/11 JL69349/10 LM300849/11 18590/20 LM501349/10 LM501349/14 LM102949/10 JLM104948/10 SPHERICAL ROLLER BEARINGS Load Rating(KN) Bore 55 55 60 60 65 65 70 70 75 75 80 80 85 85 90 90 95 95 100 100 110 110 110 120 120 120 130 130 130 140 140 140 150 150 150 160 160 160 170 170 170 180 180 180 190 d D 100 120 110 130 120 140 125 150 130 160 140 170 150 180 160 190 170 200 180 215 170 200 240 180 215 260 200 230 280 210 250 300 225 270 320 240 290 340 260 310 360 280 320 380 290 B 25 43 28 46 31 48 31 51 31 55 33 58 36 60 40 64 43 67 46 73 45 53 80 46 58 86 52 64 93 53 68 102 56 73 108 60 80 114 67 86 120 74 86 126 75 Dynamic Cr 125 270 156 310 193 340 208 400 212 440 236 490 285 550 325 610 380 670 425 815 310 560 950 355 630 965 430 735 1120 465 710 1290 510 850 1460 585 1000 1600 710 1120 1760 830 1180 2000 865 Static Cor 127 280 166 335 216 360 228 430 240 475 270 540 325 620 375 695 450 765 490 950 440 640 1120 510 765 1120 610 930 1320 680 900 1560 750 1080 1760 880 1290 1960 1060 1460 2160 1250 1560 2450 1340 NOTES: Use 'K' after bearing number for tapered bore. Page 12 Limiting Speed Grease Oil r/min r/min 6300 8500 4300 5600 5600 7500 4000 5300 5000 7000 3800 5000 5000 6700 3400 4500 4800 6300 3200 4300 4300 6000 3000 4000 4000 5600 2800 3800 3800 5300 2600 3600 3600 4800 2600 3400 3400 4500 2400 3000 3400 4300 3000 4000 2000 2800 3200 4000 2800 3800 2000 2600 2800 3600 2600 3600 1800 2400 2600 3400 2400 3200 1700 2200 2400 3200 2200 3000 1600 2000 2400 3000 2000 2800 1500 1900 2200 2800 1900 2600 1400 1800 2000 2600 1800 2600 1300 1700 1900 2400 Bearing No. 22211 22311 22212 22312 22213 22313 22214 22314 22215 22315 22216 22316 22217 22317 22218 22318 22219 22319 22220 22320 23022 22222 22322 23024 22224 22324 23026 22226 22326 23028 22228 22328 23030 22230 22330 23032 22232 22332 23034 22234 22334 23036 22236 22336 23038 SPHERICAL PLAIN BEARINGS Sliding contact surfaces: Steel / Steel Dimenisions mm Bore d 4 5 6 8 10 12 15 17 20 25 30 35 40 45 50 55 60 70 80 90 100 110 120 140 160 180 D 12 14 14 16 19 22 26 30 35 42 47 55 62 68 75 85 90 105 120 130 150 160 180 210 230 260 B 5 6 6 8 9 10 12 14 16 20 22 25 28 32 35 40 44 49 55 60 70 70 85 90 105 105 C 3 4 4 5 6 7 9 10 12 16 18 20 22 25 28 32 36 40 45 50 55 55 70 70 80 80 dk 8 10 10 13 16 18 22 25 29 35.5 40.7 47 53 60 66 74 80 92 105 115 130 140 160 180 200 225 Load ratings Dynamic Cr 2 3.4 3.4 5.5 8.1 10 16 21 30 48 62 79 99 127 156 200 245 313 400 488 607 654 950 1070 1360 1530 kN Static Cor 10 17 17 27 40 53 84 106 146 240 310 399 495 637 780 1000 1220 1560 2000 2440 3030 3270 4750 5350 6800 7650 Bearing No. GE4E GE5E GE6E GE8E GE10E GE12E GE15ES GE17ES GE20ES GE25ES GE30ES GE35ES GE40ES GE45ES GE50ES GE55ES GE60ES GE70ES GE80ES GE90ES GE100ES GE110ES GE120ES GE140ES GE160ES GE180ES NOTES: 1) All 'GE' & 'GEG' bearings from GE15ES onward stocked as 2RS types, smaller sizes not available in 2RS. 2) Some sizes available in Teflon lined maintenance free use ET or XT in place of ES. Sliding contact surfaces: Steel / Steel Dimenisions mm Bore 15 17 20 25 30 35 40 45 50 60 70 80 90 100 d D 30 35 42 47 55 62 68 75 90 105 120 130 150 160 B 16 20 25 28 32 35 40 43 56 63 70 75 85 85 C 10 12 16 18 20 22 25 28 36 40 45 50 55 55 dk 25 29 35.5 40.7 47 53 60 66 80 92 105 115 130 140 Page 13 Load ratings Dynamic Cr 21 30 48 62 79 99 127 156 245 313 400 488 607 654 kN Static Cor 106 146 240 310 399 495 637 780 1220 1560 2000 2440 3030 3270 Bearing No. GEG15ES GEG17ES GEG20ES GEG25ES GEG30ES GEG35ES GEG40ES GEG45ES GEG50ES GEG60ES GEG70ES GEG80ES GEG90ES GEG100ES SPHERICAL PLAIN BEARINGS Sliding contact surfaces: Steel / Steel Dimenisions Bore 12 15 16 17 20 25 30 32 35 40 45 50 60 63 70 80 d D 22 26 28 30 35 42 47 52 55 62 68 75 90 95 105 120 B 12 15 16 17 20 25 30 32 35 40 45 50 60 63 70 80 mm C 7 9 9 10 12 16 18 18 20 22 25 28 36 36 40 45 d1 max 15.5 18.5 20 21 25 30.5 34 37 40 46 52 57 68 71.5 78 91 dk 18 22 23 25 29 35.5 40.7 43 47 53 60 66 80 83 92 105 Load ratings kN Dynamic Static Cr Cor 10 53 16 84 17 85 21 106 30 146 48 240 62 310 65 328 79 399 99 495 127 637 156 780 245 1220 253 1260 313 1560 400 2000 Bearing No. GEEW12ES* GEEW15ES GEEW16ES GEEW17ES GEEW20ES GEEW25ES GEEW30ES GEEW32ES GEEW35ES GEEW40ES GEEW45ES GEEW50ES GEEW60ES GEEW63ES GEEW70ES GEEW80ES dk 29 35.5 40.7 47 53 60 66 80 92 105 Load ratings kN Dynamic Static Cr Cor 30 146 48 240 62 310 79 399 99 495 127 637 156 780 245 1220 313 1560 400 2000 Bearing No. GEEM20ES GEEM25ES GEEM30ES GEEM35ES GEEM40ES GEEM45ES GEEM50ES GEEM60ES GEEM70ES GEEM80ES * A lubrication groove and holes in the outer ring only. NOTES: 1) All 'GEEW & GEEM bearings are stocked as 2RS types, Sliding contact surfaces: Steel / Steel Dimenisions Bore 20 25 30 35 40 45 50 60 70 80 d D 35 42 47 55 62 68 75 90 105 120 B 24 29 30 35 38 40 43 54 65 74 mm C 12 16 18 20 22 25 28 36 40 45 d1 max 24 29 34 40 45 52 57 68 78 90 Page 14 SPHERICAL PLAIN BEARINGS Sliding contact surfaces: Steel / Steel Dimenisions mm Bore d 12.7 15.875 19.05 22.225 25.4 31.75 34.925 38.1 44.45 50.8 57.15 63.5 69.85 76.2 82.55 88.9 95.25 D 22.225 26.988 31.75 36.513 41.275 50.8 55.563 61.913 71.438 80.963 90.488 100.013 111.125 120.65 130.175 139.7 149.225 B 11.1 13.894 16.662 19.431 22.225 27.762 30.15 33.325 38.887 44.45 50.013 55.55 61.112 66.675 72.238 77.775 83.337 C 9.525 11.913 14.275 16.662 19.05 23.8 26.187 28.575 33.325 38.1 42.85 47.625 52.375 57.15 61.9 66.675 71.425 dk 18 23 27.5 32 36.5 45.5 49 54.7 63.9 73 82 92 100 109.5 119 128 137 Load ratings Dynamic Cr 13 22 31 42 56 86 102 125 170 224 280 355 415 500 585 680 780 kN Static Cor 41 65 95 127 166 260 310 375 510 670 850 1060 1250 1500 1760 2040 2360 NOTES: 1) All bearings from GEZ19ES onward stocked as 2RS types, smaller sizes not available in 2RS. ROD ENDS Dimenisions Bore 5 6 8 10 12 14 16 18 20 25 d B 8 9 12 14 16 19 21 23 25 31 mm L 41 45 53 61 69 77 85 93 101 124 Thread Size M5 M6 M8 M10 M12 M14 M16 M18 x 1.5 M20 x 1.5 M25 x 2 Load ratings kN Dynamic Static Cr Cor 3.3 3.9 4.3 5.3 6.8 8.5 10.0 11.0 13.0 14.0 17.0 20.0 21.0 25.0 26.0 30.0 31.0 35.0 47.0 65.0 NOTES: Use L for left hand threads as follows SALBP, SILBP, SALZP, SILZP Page 15 Bearing No. SABP5S SABP6S SABP8S SABP10S SABP12S SABP14S SABP16S SABP18S SABP20S SABP25S Bearing No. GEZ12ES GEZ15ES GEZ19ES GEZ22ES GEZ25ES GEZ31ES GEZ34ES GEZ38ES GEZ44ES GEZ50ES GEZ57ES GEZ63ES GEZ69ES GEZ76ES GEZ82ES GEZ88ES GEZ95ES ROD ENDS Dimenisions in Inches Bore d 0.250 0.313 0.375 0.437 0.500 0.625 0.750 1.000 B 0.375 0.437 0.500 0.562 0.625 0.750 0.875 1.375 L 1.937 2.312 2.438 2.688 3.094 3.375 3.750 5.500 Load ratings kN Dynamic Static Cr Cor 4.5 6.6 6.9 8.4 9.4 10.0 11.0 13.0 15.0 19.0 20.0 21.0 23.0 29.0 60.0 101.0 Bearing No. SAZP6S SAZP7S SAZP9S SAZP11S SAZP12S SAZP15S SAZP19S SAZP25S M5 M6 M8 M10 M12 M14 M16 M18 x 1.5 M20 x 1.5 M24 x 2 Load ratings kN Dynamic Static Cr Cor 3.3 4.1 4.3 5.3 6.8 8.5 10.0 11.0 13.0 14.0 17.0 20.0 21.0 25.0 26.0 30.0 31.0 35.0 47.0 65.0 Bearing No. SIBP5S SIBP6S SIBP8S SIBP10S SIBP12S SIBP14S SIBP16S SIBP18S SIBP20S SIBP25S Thread Size 1/4-28 5/16-24 3/8-24 7/16-20 1/2-20 5/8-18 3/416 5/4-12 Load ratings kN Dynamic Static Cr Cor 4.5 6.6 6.9 8.4 9.4 10.0 11.0 13.0 15.0 19.0 20.0 21.0 23.0 29.0 60.0 101.0 Bearing No. SIZP6S SIZP7S SIZP9S SIZP11S SIZP12S SIZP15S SIZP19S SIZP25S Thread Size 1/4-28 5/16-24 3/8-24 7/16-20 1/2-20 5/8-18 3/416 5/4-12 Dimenisions in Inches Bore d 5 6 8 10 12 14 16 18 20 25 B 8 9 12 14 16 19 21 23 25 31 L 35 39 47 56 65 74 83 92 100 124 Thread Size Dimenisions in Inches Bore d 0.250 0.313 0.375 0.437 0.500 0.625 0.750 1.000 B 0.375 0.437 0.500 0.562 0.625 0.750 0.875 1.375 L 1.687 1.812 2.125 2.375 2.781 3.25 3.75 5.5 NOTES: Use L for left hand threads as follows SALBP, SILBP, SALZP, SILZP Page 16 ROD ENDS Dimenisions in Inches Bore M5 M6 M8 M10 M12 M14 M16 M18 M20 M22 d I 29 32.5 42.5 50.5 57.5 73.5 79.5 90 90 95 L 35 40 48 57 66 75 84 93 99 109 Load ratings kN Static Cor Thread Size M5 2.2 M6 3.5 M8 6.6 M10x1.25 10.0 M12x1.25 16.0 M14x1.5 19.0 M16x1.5 26.0 M18x1.5 33.0 M20x1.5 45.0 48.0 M22x1.5 Bearing No. SQ5-RS SQ6-RS SQ8-RS SQ10-RS SQ12-RS SQ14-RS SQ16-RS SQ18-RS SQ20-RS SQ22-RS NOTES: Use L for left hand threads as follows SQL.. Dimensions mm d 10 12 15 17 20 25 30 35 40 45 50 60 70 80 d3 3 3 4 4 4 4 4 4 4 6 6 6 6 6 d4 15 17.5 21 24 27.5 33.5 40 47 52 58 62 70 80 95 Load ratings B 9 10 12 14 16 20 22 25 28 32 35 44 49 55 d2 29 34 40 46 53 64 73 82 92 102 112 135 160 180 NOTES: - Sealed design also available, eg. GK50DO-2RS. - * Relubrication not possible for sizes marked. Page 17 L4 38.5 44 51 58 64.5 77 87.5 102 115 128 144 168 195 231 Dynamic 8.15 10.8 17 21.2 30 48 62 80 100 127 156 245 315 400 kN Static 15.6 21.6 32 40 54 72 95 125 156 208 250 390 510 620 Bearing No. GK10DO* GK12DO* GK15DO GK17DO GK20DO GK25DO GK30DO GK35DO GK40DO GK45DO GK50DO GK60DO GK70DO GK80DO ROD ENDS Dimensions mm d 20 25 30 35 40 45 50 60 70 80 C1 19 23 28 30 35 40 40 50 55 60 d2 50 55 65 83 100 110 123 140 164 180 Load ratings l6 63 72.5 83.5 102.5 119 132 149.5 170 197 231 h2 38 45 51 61 69 77 88 100 115 141 Dynamic 30 48 62 80 100 127 156 245 315 400 NOTES: - Sealed design also available, eg. GF50DO-2RS. WATER PUMP BEARINGS Dimensions mm D 30 30 30 35 30 30 30 30 38.1 W 38.89 38.8 57 38.89 38.89 38.89 38.89 38.89 53.975 L 98.75 166 141 112 104.6 122 120.9 74.55 95.4 d 15.9 16 16 15.626/12 15.926 15.926 12 15.926 15.926 Bearing No. BWF30-119Z FPS061 FPS630 W7R112* 381023 382081 885105 885152** 885802 NOTES: * - Shaft different size at each end. ** - Shaft one end only. Page 18 kN Static 67 69.5 118 196 300 380 440 570 695 780 Bearing No. GF2 0 D O GF2 5 D O GF3 0 D O GF3 5 D O GF4 0 D O GF4 5 D O GF5 0 D O GF6 0 D O GF7 0 D O GF8 0 D O TRANSMISSION BEARINGS UC (YAR) Stainless Steel Available from UC202 to UC212 use prefix SS Dimensions mm Load ratings kN Bore d mm/In Dynamic Static D B C 12mm 47 31 16 12.5 6.6 1/2 in 47 31 16 12.5 6.6 15mm 47 31 16 12.5 6.6 5/8 in 47 31 16 12.5 6.6 17mm 47 31 16 12.5 6.6 20mm 47 31 16 12.5 6.6 3/4 in 47 31 16 12.5 6.6 25mm 52 34.1 17 13.7 7.7 7/8 in 52 34.1 17 13.7 7.7 15/16 in 52 34.1 17 13.7 7.7 1 in 52 34.1 17 13.7 7.7 30mm 62 38.1 19 19.1 11.0 1 1/8 in 62 38.1 19 19.1 11.0 1 3/16 in 62 38.1 19 19.1 11.0 1 1/4 in 62 38.1 19 19.1 11.0 35mm 72 42.9 20 25.2 15.1 1 1/4 in 72 42.9 20 25.2 15.1 1 3/8 in 72 42.9 20 25.2 15.1 1 7/16 in 72 42.9 20 25.2 15.1 40mm 80 49.2 21 28.5 17.5 1 1/2 in 80 49.2 21 28.5 17.5 1 9/16 in 80 49.2 21 28.5 17.5 45mm 85 49.2 22 31.4 20.0 1 5/8 in 85 49.2 22 31.4 20.0 1 11/16 in 85 49.2 22 31.4 20.0 1 3/4 in 85 49.2 22 31.4 20.0 50mm 90 51.6 23 34.4 22.7 90 51.6 23 34.4 22.7 1 7/8 in 1 15/16 in 90 51.6 23 34.4 22.7 90 51.6 23 34.4 22.7 2 in 55mm 100 51.6 25 42.4 28.8 100 51.6 25 42.4 28.8 2 in 2 1/8 in 100 51.6 25 42.4 28.8 2 3/16 in 100 51.6 25 42.4 28.8 60mm 110 65.1 27 51.4 35.4 2 1/4 in 110 65.1 27 51.4 35.4 2 3/8 in 110 65.1 27 51.4 35.4 2 7/16 in 110 65.1 27 51.4 35.4 65mm 120 65.1 29 56.0 39.2 2 1/2 in 120 65.1 29 56.0 39.2 70mm 125 74.6 29 61.0 43.1 2 3/4 in 125 74.6 29 61.0 43.1 75mm 130 77.8 30 66.0 47.2 130 77.8 30 66.0 47.2 3 in 80mm 140 82.6 32 71.0 52.0 85mm 150 85.7 34 82.2 60.5 3 1/4 in 150 85.7 34 82.2 60.5 90mm 160 96 36 94.1 70.0 3 1/2 in 160 96 36 94.1 70.0 Page 19 Bearing No. UC201 UC201-08 UC202 UC202-10 UC203 UC204 UC204-12 UC205 UC205-14 UC205-15 UC205-16 UC206 UC206-18 UC206-19 UC206-20 UC207 UC207-20 UC207-22 UC207-23 UC208 UC208-24 UC208-25 UC209 UC209-26 UC209-27 UC209-28 UC210 UC210-30 UC210-31 UC210-32 UC211 UC211-32 UC211-34 UC211-35 UC212 UC212-36 UC212-38 UC212-39 UC213 UC213-40 UC214 UC214-44 UC215 UC215-48 UC216 UC217 UC217-52 UC218 UC218-56 TRANSMISSION BEARINGS UC Dimensions mm Bore d mm 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 120 130 140 D 62 72 80 90 100 110 120 130 140 150 160 170 180 190 200 215 225 240 260 280 300 B 38 43 48 52 57 61 66 71 75 78 82 86 96 96 103 108 112 117 126 135 145 Load ratings C 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 54 56 60 64 68 72 Dynamic 20.6 26.0 32.6 40.0 47.9 60.7 70.1 80.1 90.8 101.9 110.7 120.5 130.3 140.1 149.9 169.5 180.3 200.1 202.8 224.4 247.9 kN Static 10.7 14.7 18.8 23.4 28.9 37.4 43.9 50.9 58.6 66.6 75.4 84.7 94.6 104.8 115.6 138.2 150.0 175.4 181.3 209.7 241.1 Bearing No. UC305 UC306 UC307 UC308 UC309 UC310 UC311 UC312 UC313 UC314 UC315 UC316 UC317 UC318 UC319 UC320 UC321 UC322 UC324 UC326 UC328 UCX (CX) Dimensions mm Bore d mm/In 25mm 1 in 30mm 1 1/4 in 35mm 1 3/8 in 40mm 1 1/2 in 45mm 1 3/4 in 50mm 2 in 55mm 2 1/4 in 60mm 2 3/8 in 65mm 70mm 75mm 80mm 90mm 100mm D 62 62 72 72 80 80 85 85 90 90 100 100 110 110 120 120 125 130 140 150 170 190 B 38.1 38.1 42.9 42.9 49.2 49.2 49.2 49.2 51.6 51.6 55.6 55.6 65.1 65.1 65.1 65.1 74.6 77.8 82.6 85.7 104 117.5 Load ratings C 19 19 20 20 21 21 22 22 23 23 25 25 27 27 29 29 29 30 32 34 40 43 Dynamic 19.1 19.1 25.2 19.1 28.5 28.5 31.4 31.4 34.4 34.4 42.4 42.4 51.3 51.3 56.0 56.0 61.0 66.0 71.1 82.2 106.8 130.3 Page 20 kN Static 11.1 11.1 15.1 11.1 17.5 17.5 20.0 20.0 22.7 22.7 28.8 28.8 35.4 35.4 39.2 39.2 43.1 47.2 51.9 60.5 85.3 103.0 Bearing No. UCX05 UCX05-16 UCX06 UCX06-20 UCX07 UCX07-22 UCX08 UCX08-24 UCX09 UCX09-28 UCX10 UCX10-32 UCX11 UCX11-36 UCX12 UCX12-38 UCX13 UCX14 UCX15 UCX16 UCX18 UCX20 TRANSMISSION BEARINGS HC (UEL,EW,NA,UG,FG) Dimensions mm Bore d mm/In D B 12mm 47 43.7 1/2 in 47 43.7 15mm 47 43.7 5/8 in 47 43.7 17mm 47 43.7 20mm 47 43.7 3/4 in 47 43.7 25mm 52 44.4 7/8 in 52 44.4 1 in 52 44.4 30mm 62 48.4 1 1/8 in 62 48.4 1 1/4 in 62 48.4 35mm 72 51.2 1 1/4 in 72 51.2 1 3/8 in 72 51.2 40mm 80 56.4 1 1/2 in 80 56.4 45mm 85 56.4 1 5/8 in 85 56.4 1 3/4 in 85 56.4 50mm 90 62.7 2 in 90 62.7 55mm 100 71.4 2 in 100 71.4 2 3/16 in 100 71.4 60mm 110 77.8 2 1/4 in 110 77.8 65mm 120 85.7 2 1/2 in 120 85.7 70mm 125 85.7 2 3/4 in 125 85.7 75mm 130 92.1 Load ratings C 16 16 16 16 16 16 16 17 17 17 19 19 19 20 20 20 21 21 22 22 22 23 23 25 25 25 27 27 29 29 29 29 30 Dynamic 12.5 12.5 12.5 12.5 12.5 12.5 12.5 13.7 13.7 13.7 19.1 19.1 19.1 25.2 25.2 25.2 28.5 28.5 31.4 31.4 31.4 34.4 34.4 42.4 42.4 42.4 51.4 51.4 56.0 56.0 61.0 61.0 66.0 Page 21 kN Static 6.6 6.6 6.6 6.6 6.6 6.6 6.6 7.7 7.7 7.7 11.0 11.0 11.0 15.1 15.1 15.1 17.5 17.5 20.0 20.0 20.0 22.7 22.7 28.8 28.8 28.8 35.4 35.4 39.2 39.2 43.1 43.1 47.2 Bearing No. HC201 HC201-08 HC202 HC202-10 HC203 HC204 HC204-12 HC205 HC205-14 HC205-16 HC206 HC206-18 HC206-20 HC207 HC207-20 HC207-22 HC208 HC208-24 HC209 HC209-26 HC209-28 HC210 HC210-32 HC211 HC211-32 HC211-35 HC212 HC212-36 HC213 HC213-40 HC214 HC214-44 HC215 TRANSMISSION BEARINGS UK Dimensions mm Bore d mm 25 30 35 40 45 50 55 60 65 75 80 85 90 D 52 62 72 80 85 90 100 110 120 130 140 150 160 B 17 19 20 21 22 23 25 27 29 30 32 34 36 Load ratings C 22 24 26 27 28 30 32 34 37 38 40 43 46 Dynamic 13.7 19.1 25.2 28.5 31.3 34.4 42.4 51.3 56.1 66.0 71.1 82.2 94.1 kN Static 7.7 11.1 15.1 17.5 20.0 22.7 28.8 35.4 39.2 47.2 52.0 60.5 70.0 SC (CS) Dimensions mm Bore d mm 10 12 15 17 20 25 30 D 30 32 35 40 47 52 62 Load ratings B 9 10 11 12 14 15 16 Dynamic 5.0 6.7 7.4 9.4 12.5 13.7 19.1 kN Static 2.3 2.9 3.6 4.7 6.5 7.7 11.1 Page 22 Bearing No. SC200 SC201 SC202 SC203 SC204 SC205 SC206 Bearing No. UK205 UK206 UK207 UK208 UK209 UK210 UK211 UK212 UK213 UK215 UK216 UK217 UK218 TRANSMISSION BEARINGS SA (AEL, EN, KH, YET) Dimensions mm Bore d mm/In 12mm 1/2 in 15mm 5/8 in 17mm 20mm 3/4 in 25mm 7/8 in 1 in 30mm 1 1/8 in 1 3/16 in 1 1/4 in 35mm 1 1/4 in 1 3/8 in 40mm 1 1/2 in 45mm 1 5/8 in 1 3/4 in 50mm 1 15/16 in 55mm 2 in D 40 40 40 40 40 47 47 52 52 52 62 62 62 62 72 72 72 80 80 85 85 85 90 90 100 100 B 28.6 28.6 28.6 28.6 28.6 31 31 31 31 31 35.7 35.7 35.7 35.7 38.9 38.9 38.9 43.7 43.7 43.7 43.7 43.7 43.7 43.7 48.4 48.4 Load ratings C 12 12 12 12 12 14 14 15 15 15 16 16 16 16 17 17 17 18 18 19 19 19 20 20 21 21 Dynamic 9.4 9.4 9.4 9.4 9.4 12.5 12.5 13.7 13.7 13.7 19.1 19.1 19.1 19.1 25.2 25.2 25.2 28.5 28.5 31.3 31.3 31.3 34.4 34.4 42.4 42.4 Page 23 kN Static 4.7 4.7 4.7 4.7 4.7 6.5 6.5 7.7 7.7 7.7 11.1 11.1 11.1 11.1 15.1 15.1 15.1 17.5 17.5 20.0 20.0 20.0 22.7 22.7 28.8 28.8 Bearing No. SA201 SA201-08 SA202 SA202-10 SA203 SA204 SA204-12 SA205 SA205-14 SA205-16 SA206 SA206-18 SA206-19 SA206-20 SA207 SA207-20 SA207-22 SA208 SA208-24 SA209 SA209-26 SA209-28 SA210 SA210-31 SA211 SA211-32 TRANSMISSION BEARINGS SER (UCS,ER,UR..NDG Dimensions mm Bore d mm/In D B 15mm 47 31 5/8 in 47 31 17mm 47 31 20mm 47 31 3/4 in 47 31 25mm 52 34.1 7/8 in 52 34.1 1 in 52 34.1 30mm 62 38.1 1 1/8 in 62 38.1 1 3/16 in 62 38.1 35mm 72 42.9 1 1/4 in 72 42.9 1 3/8 in 72 42.9 1 7/16 in 72 42.9 40mm 80 49.2 1 1/2 in 80 49.2 45mm 85 49.2 50mm 90 51.9 55mm 100 55.6 2 in 100 55.6 60mm 110 65.1 Load ratings C 15.8 15.8 15.8 15.8 15.8 19 19 19 22.2 22.2 22.2 23.8 23.8 23.8 23.8 27.8 27.8 27.8 28.5 30.1 30.1 31.7 Dynamic 12.5 12.5 12.5 12.5 12.5 13.7 13.7 13.7 19.1 19.1 19.1 25.2 25.2 25.2 25.2 28.5 28.5 31.3 34.4 42.4 42.4 51.3 kN Static 6.5 6.5 6.5 6.5 6.5 7.7 7.7 7.7 11.1 11.1 11.1 15.1 15.1 15.1 15.1 17.5 17.5 20.0 22.7 28.8 28.8 35.4 Bearing No. SER202 SER202-10 SER203 SER204 SER204-12 SER205 SER205-14 SER205-16 SER206 SER206-18 SER206-19 SER207 SER207-20 SER207-22 SER207-23 SER208 SER208-24 SER209 SER210 SER211 SER211-32 SER212 SB cont. (AS,UB,B) Dimensions mm Bore d mm/In 12mm 1/2 in 15mm 5/8 in 17mm 20mm 3/4 in 25mm 7/8 in 1 in 30mm 1 1/8 in 1 3/16 in 1 1/4 in D 40 40 40 40 40 47 47 52 52 52 62 62 62 62 B 22 22 22 22 22 25 25 27 27 27 30 30 30 30 Load ratings C 12 12 12 12 12 14 14 15 15 15 16 16 16 16 Dynamic 9.4 9.4 9.4 9.4 9.4 12.5 12.5 13.7 13.7 13.7 19.1 19.1 19.1 19.1 Page 24 kN Static 4.7 4.7 4.7 4.7 4.7 6.5 6.5 7.7 7.7 7.7 11.1 11.1 11.1 11.1 Bearing No. SB201 SB201-08 SB202 SB202-10 SB203 SB204 SB204-12 SB205 SB205-14 SB205-16 SB206 SB206-18 SB206-19 SB206-20 TRANSMISSION BEARINGS SB cont. (AS,UB,B) Dimensions mm Bore d mm/In D B 35mm 72 32 1 1/4 in 72 32 1 3/8 in 72 32 40mm 80 34 80 34 1 1/2 in 45mm 85 41.2 1 5/8 in 85 41.2 1 3/4 in 85 41.2 50mm 90 43.5 1 15/16 in 90 43.5 55mm 100 45.3 2 in 100 45.3 CSA (ENR,AELS,KHR,SAA) Dimensions mm Bore d mm/In D B 12mm 40 28.6 40 28.6 1/2 in 15mm 40 28.6 40 28.6 5/8 in 17mm 40 28.6 20mm 47 31 3/4 in 47 31 25mm 52 31 7/8 in 52 31 1 in 52 31 30mm 62 35.7 1 1/8 in 62 35.7 1 1/4 in 62 35.7 35mm 72 38.9 1 1/4 in 72 38.9 1 3/8 in 72 38.9 40mm 80 43.7 1 1/2 in 80 43.7 Load ratings C 17 17 17 18 18 19 19 19 20 20 21 21 Dynamic 25.2 25.2 25.2 28.5 28.5 31.3 31.3 31.3 34.4 34.4 42.4 42.4 Static 15.1 15.1 15.1 17.5 17.5 20.0 20.0 20.0 22.7 22.7 28.8 28.8 Load ratings C 13 13 13 13 13 14 14 15 15 15 16 16 16 17 17 17 18 18 Dynamic 9.4 9.4 9.4 9.4 9.4 12.5 12.5 13.7 13.7 13.7 19.1 19.1 19.1 25.2 25.2 25.2 28.5 28.5 Page 25 kN Bearing No. SB207 SB207-20 SB207-22 SB208 SB208-24 SB209 SB209-26 SB209-28 SB210 SB210-31 SB211 SB211-32 kN Static 4.7 4.7 4.7 4.7 4.7 6.5 6.5 7.7 7.7 7.7 11.1 11.1 11.1 15.1 15.1 15.1 17.5 17.5 Bearing No. CSA201 CSA201-08 CSA202 CSA202-10 CSA203 CSA204 CSA204-12 CSA205 CSA205-14 CSA205-16 CSA206 CSA206-18 CSA206-20 CSA207 CSA207-20 CSA207-22 CSA208 CSA208-24 TRANSMISSION HOUSINGS P200 (SY) a Part No. P203 P204 P205 P206 P207 P208 P209 P210 P211 P212 P213 P214 P215 P216 P217 P218 127 127 140 165 167 184 190 206 219 241 265 266 275 292 310 327 Dimensions mm e w 95 95 105 121 127 137 146 159 171 184 203 210 217 232 247 262 60 64 71 84 93 98 106 113 125 138 150 156 162 174 185 198 Bolt Hole h 30.2 33.3 36.5 42.9 47.6 49.2 54.0 57.2 63.5 69.8 76.2 79.4 82.6 88.9 95.2 101.6 S1 13 13 13 17 17 17 17 20 20 20 25 25 25 25 25 27 S2 19 19 19 21 21 21 21 22 22 25 30 30 30 35 40 45 PX a Part No. PX05 PX06 PX07 PX08 PX09 PX10 PX11 PX12 PX13 PX14 PX15 PX16 PX17 PX18 PX20 159 175 203 222 222 241 260 286 286 330 330 381 381 381 432 Dimensions mm e w 119 127 144 156 156 171 184 203 203 229 229 283 283 283 337 86 93 105 114 116 126 139 152 155 171 175 195 200 204 245 Bolt Hole h 44.4 47.6 54.0 58.7 58.7 63.5 69.8 76.2 76.2 88.9 8.9 101.6 101.6 101.6 127.0 S1 17 17 17 20 20 20 25 25 25 27 27 27 27 27 33 S2 25 25 30 32 33 36 36 40 40 50 50 58 60 60 65 P300 a Part No. P305 P306 P307 P308 P309 P310 P311 P312 P313 P314 P315 175 180 210 220 245 275 310 330 340 360 380 Dimensions mm e w 132 140 160 170 190 212 236 250 260 280 290 85 95 107 118 132 148 158 167 176 186 198 Page 26 Bolt Hole h 45 50 56 60 67 75 80 85 90 95 100 S1 17 17 17 17 20 20 20 25 25 27 27 S2 20 20 25 27 30 35 38 38 38 40 40 TRANSMISSION HOUSINGS P300 cont. a Part No. P316 P317 P318 P319 P320 P321 P322 400 420 430 470 490 490 520 Dimensions mm e w 300 320 330 360 380 380 400 209 220 234 248 273 278 296 Bolt Hole h 106 112 118 125 140 140 150 S1 27 33 33 36 36 36 40 PA200 (UP) a Part No. PA204 PA205 PA206 PA207 PA208 PA209 PA210 76 84 94 110 116 120 130 Dimensions mm e w 52 56 66 80 84 90 94 62 72 84 95 100 108 116 Bolt Hole h 30.2 36.5 42.9 47.6 49.2 54.2 57.2 Page 27 Sx2 10 10 14 14 14 14 16 S2 40 45 45 50 50 50 55 TRANSMISSION HOUSINGS SB200 Bolt Hole Dimensions mm Part No. SB205 SB206 SB207 SB208 SB209 SB210 SB211 SB212 SB213 SB214 SB215 SB216 SB217 SB218 H 31.70 38.10 44.40 47.60 50.80 53.97 58.70 69.85 69.85 76.20 76.20 82.55 88.90 98.40 A 92 108 133 140 146 152 172 197 197 206 206 238 254 273 E 70 83 102 108 111 118 137 162 162 172 172 191 203 222 G 58 68 76 81 86 90 98 111 111 117 117 127 136 152 F200 (FY) F300 Dimensions mm Part No. F204 F205 F206 F207 F208 F209 F210 F211 F212 F213 F214 F215 F216 F217 F218 Sx2 11 11 14 14 14 14 17 17 17 17 17 21 21 25.4 a 86 95 108 117 130 137 143 162 175 187 193 200 208 220 235 e 64 70 83 92 102 105 111 130 143 149 152 159 165 175 187 Dimensions mm Bolt Hole x4 12 12 12 14 16 16 16 19 19 19 19 19 23 23 23 Part No. F305 F306 F307 F308 F309 F310 F311 F312 F313 F314 F315 F316 F317 F318 F319 F320 F321 F322 NOTE: F200 Series available in Plastic prefix PL F200 Series available in Stainless Steel prefix SS Page 28 a 110 125 135 150 160 175 185 195 208 226 236 250 260 280 290 310 310 340 e 80 95 100 112 125 132 140 150 166 178 184 196 204 216 228 242 242 266 Bolt Hole x4 16 16 19 19 19 23 23 23 23 25 25 31 31 35 35 38 38 41 TRANSMISSION HOUSINGS FX Dimensions mm Part No. FX05 FX06 FX07 FX08 FX09 FX10 FX11 FX12 FX13 FX14 FX15 FX16 FX17 FX18 FX20 a 108 117 130 137 143 162 175 187 187 197 197 214 214 214 268 Bolt Hole e 83 92 102 105 111 130 143 149 149 152 152 171 171 171 211 x4 12 16 16 19 19 19 19 19 19 23 23 23 23 23 31 FL200 Bolt Hole Dimensions mm Part No. FL204 FL205 FL206 FL207 FL208 FL209 FL210 FL211 FL212 FL213 FL214 FL215 FL216 FL217 FL218 a 113 130 148 161 175 188 197 224 250 258 265 275 290 305 320 e 90 99 117 130 144 148 157 184 202 210 216 225 233 248 265 b 60 68 80 90 100 108 115 130 140 155 160 165 180 190 205 Bolt Hole Dimensions mm Part No. LF203 LF204 LF205 LF206 LF207 a 81 90 95 113 122 e 63.5 71.5 76 90.5 100 Sx2 12 16 16 16 16 19 19 19 23 23 23 23 25 25 25 b 52 61 64 76 89 Sx2 8 10 10 12 12 Page 29 NOTES: FL200 in Plastic, prefix PL FL200 in Stainless Steel, prefix SS TRANSMISSION HOUSINGS Dimensions mm Part No. FC204 FC205 FC206 FC207 FC208 FC209 FC210 FC211 FC212 FC213 FC214 FC215 FC216 FC217 FC218 Part Number HA204 HA205 HA206 HA207 HA208 HA209 HA210 HA211 HA212 a 100 115 125 135 145 160 165 185 195 205 215 220 240 250 265 Bolt Hole e 55.1 63.6 70.7 77.8 84.8 93.3 97.6 106.1 113.1 120.1 125.1 130.1 141.4 147.1 155.5 Sx4 12 12 12 14 14 16 16 19 19 19 19 19 23 23 23 Dimensions mm a 64 78 78 92 96 108 118 126 142 W 96 103 103 116 121 136 142 150 173 h 64 64 64 70 73 82 83 87 102 Part No. C204 C205 C206 C207 C208 C209 C210 C211 C212 C213 Bolt Hole K (in) 3/4 3/4 3/4 3/4 3/4 1 1 1 1/4 1 1/4 Page 30 a 72 80 85 90 100 110 120 125 130 140 TRANSMISSION HOUSINGS Part Number FA204 FA205 FA206 FA207 FA208 FA209 FA210 Part Number PFL3 PFL4 PFL5 PFL6 PFL7 Part Number PF3 PF4 PF5 PF6 PF7 PF8 Dimensions mm a 98 124 141 155 171 179 189 b 59 70 83 96 105 111 116 e 78 98 117 130 144 148 157 Dimensions mm a 81 91 96 113 123 e 63.5 71.5 76 90.5 100 Dimensions mm a 81 91 96 113 123 148 e 63.5 71.5 76 90.5 100 119 b 59 67 71 84 94 Bolt Hole S1 mm S2 mm 10 40 11 49 11 56 13 63 13 70 15 72 15 75 Bolt Hole S x 2 mm 7.1 8.7 8.7 11 10.5 Bolt Hole S x 3 mm 7.1 8.7 8.7 10.5 10.5 13.5 Page 31 TRANSMISSION HOUSINGS Part Number Dimensions mm a 86 98 108 118 129 e 68 76 86 95 106 w 43.5 0.5 56.6 66.3 78 Part Number O.D. mm Width mm Fits Bearing R5 R6 R7 52.5 62.3 72.5 17.4 19.5 21.3 UC205 UC206 UC207 dxAxExB mm W mm 106 109 112 127 133 148 154 175 181 192 209 215 239 Bolt Hole PP3 PP4 PP5 PP6 PP7 h 22.2 25.4 28.6 33.3 39.7 Bolt Hole S mm 9.5 9.5 11.5 11.5 1.5 Rubber Inserts Part Number SNU 508 35x205x170x60 SNU 509 40x205x170x60 SNU 510 45x205x170x60 SNU 511 50x255x210x70 SNU 512 55x255x210x70 SNU 513 60x275x230x80 SNU 515 65x280x230x80 SNU 516 70x315x260x90 SNU 517 75x320x260x90 SNU 518 80x345x290x100 SNU 519 85x345x290x100 SNU 520 90x380x320x110 SNU 522 100x410x350x120 P K 15 15 15 18 18 18 18 22 22 22 22 26 26 20 20 20 23 23 24 26 29 30 27 27 32 32 Bearing No. 22208K 22209K 22210K 22211K 22212K 22213K 22215K 22216K 22217K 22218K 22219K 22220K 22222K Page 32 23218K 23220K 23222K Adapter Sleeve 1208K 1209K 1210K 1211K 1212K 1213K 1215K 1216K 1217K 1218K 1219K 1220K 1222K H308 H208 H309 H209 H310 H210 H311 H211 H312 H212 H313 H213 H315 H215 H316 H216 H317 H217 H318/2318 H218 H319 H219 H320/2320 H220 H322/2322 H222 ADAPTOR SLEEVES Part Number LxDxC mm H204 H205 H206 H207 H208 H209 H210 H211 H212 H213 H214 H215 H216 H217 H218 H219 H220 H221 H222 24 X 32 X 7 26 X 38 X 8 27 X 45 X 8 29 X 52 X 9 31 X 58 X 10 33 X 65 X 11 35 X 70 X 12 37 X 75 X 12 38 X 80 X 13 40 X 85 X 14 41 X 92 X 14 43 X 98 X 15 46 X 105 X 17 50 X 110 X 18 52 X 120 X 18 55 X 125 X 19 58 X 130 X 20 60 X 140 X 20 63 X 145 X 21 Part Number LxDxC mm H2304 H2305 H2306 H2307 H2308 H2309 H2310 H2311 H2312 H2313 H2314 H2315 H2316 H2317 H2318 H2319 H2320 H2321 H2322 H2324 H2326 H2328 H2330 H2332 H2334 H2336 H2338 H2340 31 X 32 X 7 35 X 38 X 8 38 X 45 X 8 43 X 52 X 9 46 X 58 X 10 50 X 65 X 11 55 X 70 X 12 59 X 75 X 12 62 X 80 X 13 65 X 85 X 14 68 X 92 X 14 73 X 98 X 15 78 X 105 X 17 82 X 110 X 18 86 X 20 X 18 90 X 125 X 19 97 X 130 X 20 101 X 140 X 20 105 X 145 X 21 112 X 155 X 22 121 X 165 X 23 131 X 180 X 24 139 X 195 X 26 147 X 210 X 28 154 X 220 X 29 161 X 230 X 30 169 X 240 X 31 176 X 250 X 32 H d mm 17 20 25 30 35 40 45 50 55 60 60 65 70 75 80 85 90 95 100 d in. ---3/4 1 1 1/4 1 1/4 1 1/2 1 3/4 2 2 1/4 2 1/4 ---2 1/2 2 3/4 3 3 1/4 3 1/4 3 1/2 ---4 H d mm 17 20 25 30 35 40 45 50 55 60 60 65 70 75 80 85 90 95 100 110 115 125 135 140 150 160 170 180 d in. ---3/4 1 1 1/4 1 1/4 1 1/2 1 3/4 2 2 1/4 2 1/4 ---2 1/2 2 3/4 3 3 1/4 3 1/4 3 1/2 ---4 4 1/4 4 1/2 5 5 1/4 5 1/2 6 6 1/2 6 3/4 7 HE HE Part Number LxDxC mm H304 H305 H306 H307 H308 H309 H310 H311 H312 H313 H314 H315 H316 H317 H318 H319 H320 H321 H322 28 X 32 X 7 29 X 38 X 8 31 X 45 X 8 35 X 52 X 9 36 X 58 X 10 39 X 65 X 11 42 X 70 X 12 45 X 75 X 12 47 X 80 X 13 50 X 85 X 14 52 X 92 X 14 55 X 98 X 15 59 X 105 X 17 63 X 110 X 18 65 X 120 X 18 68 X 125 X 19 71 X 130 X 20 74 X 140 X 20 77 X 145 X 21 Part Number LxDxC mm H3024 H3026 H3028 H3030 H3032 H3034 H3036 H3038 H3040 72 X 145 X 22 80 X 155 X 23 82 X 165 X 24 87 X 180 X 26 93 X 190 X 28 101 X 200 X 29 109 X 210 X 30 112 X 220 X 31 120 X 240 X 32 Part Number LxDxC mm H3120 H3122 H3124 H3126 H3128 H3130 H3132 H3134 H3136 H3138 H3140 76 X 130 X 20 Page 33 81 X 145 X 21 88 X 155 X 22 92 X 165 X 23 97 X 180 X 24 111 X 195 X 26 119 X 210 X 28 122 X 220 X 29 131 X 230 X 30 141 X 240 X 31 150 X 250 X 32 H d mm 17 20 25 30 35 40 45 50 55 60 60 65 70 75 80 85 90 95 100 d in. ---3/4 1 1 1/4 1 1/4 1 1/2 1 3/4 2 2 1/4 2 1/4 ---2 1/2 2 3/4 3 3 1/4 3 1/4 3 1/2 ---4 H d mm 110 115 125 135 140 150 160 170 180 d in. 4 1/4 4 1/2 5 5 1/4 5 1/2 6 6 1/2 6 3/4 7 H d mm 90 100 110 115 125 135 140 150 160 170 180 d in. 3 1/2 4 4 1/4 4 1/2 5 5 1/4 5 1/2 6 6 1/2 6 3/4 7 HE HE HE LOCK NUTS & LOCK WASHERS Part Number DxB mm D1 Thread Part Number D 4 x D5 mm D1 mm KM00 KM01 KM02 KM03 KM04 KM05 KM06 KM07 KM08 KM09 KM10 KM11 KM12 KM13 KM14 KM15 KM16 KM17 KM18 KM19 KM20 KM21 KM22 KM23 KM24 KM25 KM26 KM27 KM28 KM29 KM30 KM31 KM32 KM33 KM34 KM36 KM38 KM40 18 X 4 22 X 4 25 X 5 28 X 5 32 X 6 38 X 7 45 X 7 52 X 8 58 X 9 65 X 10 70 X 11 75 X 11 80 X 11 85 X 12 92 X 12 98 X 13 105 X 15 110 X 16 120 X 16 125 X 17 130 X 18 140 X 18 145 X 19 150 X 19 155 X 20 160 X 21 165 X 21 175 X 22 180 X 22 190 X 24 195 X 24 200 X 25 210 X 25 210 X 26 220 X 26 230 X 27 240 X 28 250 X 29 M10x0.75 M12 x 1 M15 x 1 M17 x 1 M20 x 1 M25 x 1.5 M30 x 1.5 M35 x 1.5 M40 x 1.5 M45 x 1.5 M50 x 1.5 M55 x 2 M60 x 2 M65 x 2 M70 x 2 M75 x 2 M80 x 2 M85 x 2 M90 x 2 M95 x 2 M100 x 2 M102 x 5 M110 x 2 M115 x 2 M120 x 2 M125 x 2 M130 x 2 M135 x 2 M140 x 2 M145 x 2 M150 x 2 M155 x 3 M160 x 3 M165 x 3 M170 x 3 M180 x 3 M190 x 3 M200 x 3 MB00 MB01 MB02 MB03 MB04 MB05 MB06 MB07 MB08 MB09 MB10 MB11 MB12 MB13 MB14 MB15 MB16 MB17 MB18 MB19 MB20 MB21 MB22 MB23 MB24 MB25 MB26 MB27 MB28 MB29 MB30 MB31 MB32 MB33 MB34 MB36 MB38 MB40 13 X 21 17 X 25 21 X 28 24 X 32 26 X 36 32 X 42 38 X 49 44 X 57 50 X 62 56 X 69 61 X 74 67 X 81 73 X 86 79 X 92 85 X 98 90 X 104 95 X 112 102 X 119 108 X 126 113 X 133 120 X 142 126 X 145 133 X 154 137 X 159 138 X 164 148 X 170 149 X 175 160 X 185 160 X 192 172 X 202 171 X 205 182 X 212 182 X 217 193 X 222 193 X 232 203 X 242 214 X 252 226 X 262 10 12 15 17 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170 180 190 200 UNGROUND BEARINGS Part Number UG12F22 UG20MMF22 UG10F22 UG16F32 UG08F18 UG10F22 UG12F22 UGF1047 UGFH1047 UGFH1147 OD ID In/mm In/mm 0.75 1.375 20mm 1.375 0.625 1.375 1 2 0.5 1.125 0.625 1.375 0.75 1.375 10.7mm 47.4mm 10.10mm 47.6mm 11.40mm 47.6mm Width In/mm 11.80mm 11.80mm 11.80mm 13.15mm 8.40mm 8.40mm 8.40mm 14.70mm 11.80mm 11.80mm Page 34 AGRICULTURAL BEARINGS SQUARE BORE GBC A Bore Size Part No. B O.D Ring Width Inner Outer W208PPB6 1" 80mm (S) 1.437" 18mm W208PP6 1" 80mm (C) 1.437" 18mm W208PPB5 1 1/8" 80mm (S) 1.437" 18mm W208PP5 1 1/8" 80mm (C) 1.437" 18mm W208PPB8 1 1/8" 80mm (S) 1.437" 1.187" GW208PPB8 1 1/8" 80mm (C) 1.437" 1.187" W208PPB12 1 1/8" 87mm (S) 1.437" 1.187" GW208PP17 1 1/8" 3.375" (C) 1.437" 1.187" W211PPB3 1 1/2" 100mm (S) 1.312" 1.312" GW211PPB3 1 1/2" 100mm (S) 1.312" 1.312" FAG Part No. TYPE 1 4 1 4 1 1 3 1 2 2 5 5 4 3 DS208TT6 DC208TT6 DS208TT5 DC208TT5 DS208TT8 DS208TTR8 DS208TT12 DC208TTR17 DS211TT3 DS211TTR3 W211PP3 1 1/2" 100mm (C) 1.312" 1.312" GW211PP3 1 1/2" 100mm (C) 1.312" 1.312" GW211PP5 1 1/2" 4.000" (C) 1.750" 1.437" W211PPB6 1 1/2" 4.125" (S) 1.750" 1.437" GW211PPB11 1 1/2" 100mm (S) 1.750" 25mm DC211TTR4 W211PP30 40mm 100mm (C) 1.312" 25mm DC211TT40A W211PP34 40mm 4.000" (C) 1.750" 1.437" **** 40mm 101.6mm (C) 1.75" 1.438" DC211TT40 ROUND BORE GBC A Bore Size Part No. B O.D Ring Width Inner Outer DC211TT3 DC211TTR3 DC211TT5 DS211TT6 FAG Part No. TYPE **** 1/2" 40mm (C) 18.29mm 12mm 203RRAR8 **** 12.56mm 47mm (C) 18.29mm 12mm 203RRH10 **** 5/8" 1.375" (C) 11mm 11mm 202FFLB **** 16mm 40mm (C) 18.29mm 12mm 203RRAR10 **** 16mm 45.225 (C) 18.66mm 15.49mm 205PPB7 15/16" 52mm (S) 1.3748" 15mm **** 3/4" 45.225 (C) 15.49mm 15.49mm 204FREN 1 205TTH 204BBAR **** 3/4" 62mm 24mm 16mm 206GGH W208PP10 1 1/2" 80mm (C) 1.687" 21mm DC208TT10 GW211PPB13 1.775" 100mm (S) 1.312" 25mm GW209PPB2 45mm 85mm (S) 1.187" 1.187" W211PPB2 2.1875" 100mm (S) 1.312" 1.312" GW211PPB2 2 3/16" 100mm (S) 1.312" 1.312" GW211PP2 2 3/16" 100mm (C) 1.312" 1.312" **** 2 3/16" 100mm (S) 1.562" 25mm GW214PP2 2 3/4" 125mm (C) 1.562" 1.562" 1 2 2 2 5 DS211TTR13 5 DC214TTR2 DS209TTR2 DS211TT2 DS211TTR2 DC211TTR2 DS211TTR9 GW214PPB2 2 3/4" 125mm (S) 1.562" 1.562" **** GW214PPB5 70mm 125mm (S) 2.437" 1.562" DS214TTR5 Note: (S) denotes Spherical O.D. (C) denotes Cylindrical O.D. (SQ) denotes Square Bore (RD) denotes Round Bore Page 35 AGRICULTURAL BEARINGS cont. FLANGED DISC UNITS GBC d Part No. Bore Size F O.D Width G Mnt.Hole E FAG Part No. TYPE ---- 1 1/8" (SQ) 127 44.45 13.5 FD210R ---- 2 3/16" (RD) 139.7 55.56 13.5 FD211RB ---- 1 1/2" (SQ) 139.7 50.85 17.5 x 13.5 FD211RM DHU40S-211 40mm (SQ) 139.7 50.85 13.5 FD211RP Note: (S) denotes Spherical O.D. (C) denotes Cylindrical O.D. (SQ) denotes Square Bore (RD) denotes Round Bore DU BUSHES (MB) Metric Bushes Part dxDxL Number mm Part Number dxDxL mm 0610DU 6 X 8 x 10 3230DU 32 X 36 x 30 0812DU 8 X 10 x 12 3240DU 32 X 36 x 40 1010DU 10 X 12 x 10 3520DU 35 X 39 x 20 1015DU 10 X 12 x 15 3540DU 35 X 39 x 40 1020DU 10 X 12 x 20 4030DU 40 X 44 x 30 1215DU 12 X 15 x 15 4050DU 40 X 44 x 50 1225DU 12 X 12 x 25 4520DU 45 X 50 x 20 1415DU 14 X 16 x 15 4550DU 45 X 50 x 50 1425DU 14 X 16 x 25 5030DU 50 X 55 x 30 1510DU 15 X 17 x 10 5060DU 50 X 55 x 60 1515DU 15 X 17 x 15 5525DU 55 X 60 x 25 1525DU 15 X 17 x 25 5560DU 55 X 60 x 60 1615DU 16 X 18 x 15 6030DU 60 X 65 x 30 1625DU 16 X 18 x 25 6060DU 60 X 65 x 60 1720DU 17 X 19 x 20 6560DU 65 X 70 x 60 1815DU 18 X 20 x 15 7060DU 70 X 75 x 60 1825DU 18 X 20 x 25 7560DU 75 X 80 x 60 2015DU 20 X 23 x 15 8060DU 80 X 85 x 60 2025DU 20 X 23 x 25 8560DU 85 X 90 x 60 2225DU 22 X 25 x 25 9060DU 90 X 95 x 60 2415DU 24 X 27 x 15 9560DU 95 X 100 x 60 95 X 100 x 100 2425DU 24 X 27 x 25 95100DU 2515DU 25 X 28 x 15 10060DU 100 X 105 x 60 2520DU 25 X 28 x 20 100115DU 100 X 105 x 115 110 X 115 x 115 2525DU 25 X 28 x 25 110115DU 2550DU 25 X 28 x 50 11570DU 115 X 120 x 70 2825DU 28 X 32 x 25 120100DU 120 X 125 x 100 3025DU 30 X 34 x 25 125100DU 125 X 130 x 100 3040DU 30 X 34 x 40 130100DU 130 X 135 x 100 Page 36 DU BUSHES cont. (MB) Metric Bushes Cont. Part dxDxL Number mm 135100DU 135 X 140 x 100 140100DU 140 X 145 x 100 145100DU 145 X 150 x 100 150100DU 150 X 15 x 100 155100DU 155 X 160 x 100 160100DU 160 X 165 x 100 165100DU 165 X 170 x 100 170100DU 170 X 175 x 100 175100DU 175 X 180 x 100 180100DU 180 X 185 x 100 200100DU 200 X 205 x 100 220100DU 220 X 225 x 100 250100DU 250 X 255 x 100 280100DU 280 X 285 x 100 300100DU 300 X 305 x 100 (IB) Imperial Bushes dxDxL Part in. Number 02DU03 .1243x.1878x.1875 03DU06 .1554x.2191x.375 04DU06 .249x.3128x.375 05DU08 .3116x.3753x.5 06DU06 .374x.4691x.375 06DU12 .374x.4691x.75 07DU12 .4365x.5316x.75 08DU08 .499x.5941x.5 08DU10 .499x.5941x..625 08DU14 .499x.5941x.875 09DU12 .5615x.6566x.75 10DU14 .624x.7192x.875 .7491x.8755x.5 12DO08 .7491x.8755x.75 12DU12 12DU16 .7491x.8755x1.0 14DU12 .8741x1.0x.75 .8741x1.0x1.0 14DU16 .9991x1.1255x.75 16DU12 .9991x1.1255x1.0 16DU16 .9991x1.1255x1.5 16DU24 1.1238x1.2818x.5 18DU08 1.1238x1.2818x1.0 18DU16 1.2488x1.4068x1.0 20DU16 1.2488x1.4068x1.75 20DU28 1.3738x1.5318x1.0 22DU16 1.3738x1.5318x1.75 22DU28 1.4988x1.6568x1.0 24DU16 1.4988x1.6568x1.5 24DU24 1.4988x1.6568x2.0 24DU32 1.6238x1.7818x1.5 26DU24 1.7487x1.9381x1.0 28DU16 1.7487x1.9381x2.0 28DU32 1.8737x2.0633x1.0 30DU16 1.8737x2.0633x2.0 30DU36 1.9987x2.1883x2.0 32DU32 1.9987x2.1883x2.5 32DU40 2.2507x2.4377x2.0 36DU32 2.5011x2.6881x3.0 40DU48 2.75x2.9370x2.0 44DU32 2.75x2.9370x3.5 44DU56 3.0x3.1872x2.0 48DU32 3.0x3.1872x3.0 48DU48 3.5x3.6872x2.5 56DU40 3.5x3.6872x3.75 56DU60 64DU32 4.0x4.1872x2.0 4.0x4.1872x3.0 64DU48 4.9986x5.186x3.0 80DU48 6.0x6.1874x3.0 96DU48 Metric Washers Part dxDxT Number mm 10 X 20 X 1.5 WC10 12 X 24 X 1.5 WC12 14 X 26 X 1.5 WC14 16 X 30 X 1.5 WC16 18 X 32 X 1.5 WC18 20 X 36 X 1.5 WC20 22 X 38 X 1.5 WC22 24 X 42 X 1.5 WC24 26 X 44 X 1.5 WC26 28 X 48 X 1.5 WC28 32 X 54 X 1.5 WC32 38 X 62 X 1.5 WC38 42 X 66 X 1.5 WC42 48 X 74 X 2 WC48 52 X 78 X 2 WC52 WC62 62 X 90 X 2 Page 37 INTERNAL CIRCLIPS Part Number Bore Size d1 mm 1300/08 1300/09 1300/10 1300/11 1300/12 1300/13 1300/14 1300/15 1300/16 1300/17 1300/18 1300/19 1300/20 1300/21 1300/22 1300/24 1300/25 1300/26 1300/27 1300/28 1300/29 1300/30 1300/31 1300/32 1300/34 1300/35 1300/37 1300/40 1300/41 1300/42 1300/43 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 24 25 26 27 28 29 30 31 32 34 35 37 40 41 42 43 d3 mm 8.70 9.80 10.80 11.80 13.00 14.10 15.00 16.20 17.30 18.30 19.50 20.50 21.50 22.50 23.50 25.90 26.90 27.90 29.10 30.10 31.10 32.10 33.40 34.40 36.50 37.80 39.80 43.50 44.50 45.50 46.50 s mm Part Number Bore Size d1 mm 0.80 0.80 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.20 1.20 1.20 1.20 1.20 1.20 1.20 1.20 1.20 1.50 1.50 1.50 1.75 1.75 1.75 1.75 1300/45 1300/47 1300/48 1300/50 1300/51 1300/52 1300/55 1300/57 1300/62 1300/63 1300/65 1300/68 1300/70 1300/72 1300/75 1300/78 1300/80 1300/81 1300/85 1300/90 1300/95 1300/100 1300/110 1300/115 1300/120 1300/125 1300/130 1300/140 1300/150 1300/155 1300/200 45 47 48 50 51 52 55 57 62 63 65 68 70 72 75 78 80 81 85 90 95 100 110 115 120 125 130 140 150 155 200 d3 mm 48.50 50.50 51.50 54.20 55.20 56.20 59.20 61.20 66.20 67.20 69.20 72.50 74.50 76.50 79.50 82.50 85.50 86.50 90.50 95.50 100.50 105.50 117.00 122.00 127.00 132.00 137.00 147.00 158.00 164.00 209.50 Please Note that Stainless Steel is also available by using the prefix SS Page 38 s mm 1.75 1.75 2.00 2.00 2.00 2.00 2.00 2.00 2.00 2.00 2.50 2.50 2.50 2.50 2.50 2.50 2.50 2.50 3.00 3.00 3.00 3.00 4.00 4.00 4.00 4.00 4.00 4.00 4.00 4.00 4.00 EXTERNAL CIRCLIPS Part Number Shaft Size d1 mm 1400/04 1400/05 1400/06 1400/07 1400/08 1400/09 1400/10 1400/11 1400/12 1400/13 1400/14 1400/15 1400/16 1400/17 1400/18 1400/19 1400/20 1400/22 1400/23 1400/24 1400/25 1400/28 1400/30 1400/32 1400/35 1400/38 1400/40 1400/42 1400/45 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 22 23 24 25 28 30 32 35 38 40 42 45 C1 mm 8.60 10.30 11.70 13.50 14.70 16.00 17.00 18.00 19.00 20.20 21.40 22.60 23.80 25.00 26.20 27.20 28.40 30.80 32.00 33.20 34.20 37.90 40.50 43.00 46.80 50.20 52.60 55.70 59.10 d3 s mm mm 3.70 4.70 5.60 6.50 7.40 8.40 9.30 10.20 11.00 11.90 12.90 13.80 14.70 15.70 16.50 17.50 18.50 20.50 21.00 22.20 23.20 25.90 27.90 29.60 32.20 35.20 36.00 38.50 41.50 0.40 0.60 0.70 0.80 0.80 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.20 1.20 1.20 1.20 1.20 1.20 1.20 1.50 1.50 1.50 1.50 1.75 1.75 1.75 1.75 Part Number 1400/48 1400/50 1400/55 1400/57 1400/58 1400/60 1400/62 1400/63 1400/65 1400/70 1400/75 1400/78 1400/80 1400/85 1400/90 1400/95 1400/100 1400/105 1400/110 1400/120 1400/130 1400/140 1400/150 1400/160 1400/170 1400/180 1400/190 1400/200 Shaft Size d1 mm 48 50 55 57 58 60 62 63 65 70 75 78 80 85 90 95 100 105 110 120 130 140 150 160 170 180 190 200 C1 mm 62.50 64.50 70.20 72.30 73.60 75.60 77.80 79.00 81.40 87.00 92.70 96.10 98.10 103.30 108.50 114.80 120.20 126.20 131.20 143.10 154.40 165.20 177.30 188.00 198.40 210.00 220.00 230.00 d3 s mm mm 44.50 45.80 50.80 52.80 53.80 55.80 57.80 58.80 60.80 65.50 70.50 73.50 74.50 79.50 84.50 89.50 94.50 98.00 103.00 113.00 123.00 133.00 142.00 151.00 160.50 170.50 180.50 190.50 1.75 2.00 2.00 2.00 2.00 2.00 2.00 2.00 2.50 2.50 2.50 2.50 2.50 3.00 3.00 3.00 3.00 4.00 4.00 4.00 4.00 4.00 4.00 4.00 4.00 4.00 4.00 4.00 Please Note that Stainless Steel is also available by using the prefix SS Page 39 SPA TAPER LOCK PULLEYS Part Number SPA63-1-1108 SPA67-1-1108 SPA71-1-1108 SPA75-1-1108 SPA80-1-1210 SPA85-1-1210 SPA90-1-1210 SPA95-1-1210 SPA100-1-1610 SPA106-1-1610 SPA112-1-1610 SPA118-1-1610 SPA125-1-1610 SPA132-1-1610 SPA140-1-1610 SPA150-1-1610 SPA160-1-1610 SPA170-1-1610 SPA180-1-1610 SPA190-1-1610 SPA200-1-2010 SPA212-1-2012 SPA224-1-2012 SPA236-1-2012 SPA250-1-2012 SPA280-1-2012 SPA300-1-2012 SPA315-1-2012 SPA355-1-2012 Bush No. 1008 1108 1210 & 1215 1610 & 1615 2012 & 2017 2517 & 2525 1 20 2 35 No. of Grooves Dimension F PCD OD 63 68.5 67 72.5 71 76.5 75 80.5 80 85.5 1108 1108 1108 1108 1210 1108 1108 1108 1108 1210 85 90 95 100 106 112 118 125 132 140 150 160 170 180 190 200 212 224 236 250 280 300 315 355 1210 1210 1210 1610 1610 1610 1610 1610 1610 1610 1610 1610 1610 1610 1610 2012 2012 2012 2012 2012 2012 2012 2012 2012 1210 1610 1610 1610 1610 1610 1610 1610 2012 2012 2012 2012 2012 2012 2012 2517 2517 2517 2517 2517 2517 2517 2517 2517 90.5 95.5 100.5 105.5 111.5 117.5 123.5 130.5 137.5 145.5 155.5 165.5 175.5 185.5 195.5 205.5 217.5 229.5 241.5 255.5 285.5 305.5 320.5 360.5 Taperlock Number D im e n sion P Q R W Q R W SPA 15 10 2.75 12.8 10 2.75 12.8 Stock Bore mm 9, 10, 11, 12, 14, 16, 18, 19, 20, 22, 24, 25 inch 3/8, 1/2, 5/8, 3/4, 7/8, 1 mm 9, 10, 11, 12, 14, 16, 18, 19, 20, 22, 24, 25, 28 inch 3/8, 1/2, 5/8, 3/4, 7/8, 1, 1.1/8 mm 11, 12, 14, 16, 18, 19, 20, 22, 24, 25, 28, 30, 32 inch 1/2, 5/8, 3/4, 7/8, 1, 1.1/8, 1.1/4 mm 12, 14, 16, 18, 19, 20, 22, 24, 25, 28, 30, 32, 35, 38, 40, 42 inch 1/2, 5/8, 3/4, 7/8, 1, 1.1/8, 1.1/4, 1.3/8, 1.1/2, 1.5/8 mm 14, 16, 18, 19, 20, 22, 24, 25, 28, 30, 32, 35, 38, 40, 42, 45, 48, 50 inch 3/4, 7/8, 1, 1.1/8, 1.1/4, 1.3/8, 1.1/2, 1.5/8, 1.3/4, 1.7/8, 2 mm 16, 18, 19, 20, 22, 24, 25, 28, 30, 32, 35, 38, 40, 42, 45, 48, 50, 55, 60, (65) inch 3/4, 7/8, 1, 1.1/8, 1.1/4, 1.3/8, 1.1/2, 1.5/8, 1.3/4, 1.7/8, 2, 2.1/8, 2.1/4, 2.3/8, 2.1/2 Page 40 SPB 19 12.5 3.5 16.2 12.5 3.5 16.2 ROLLER CHAIN Part Number 05B-1R 06B-1R 08B-1R 10B-1R 12B-1R 16B-1R Part Number 35-1R 40-1R 50-1R 60-1R Pitch P 8 9.53 12.7 15.88 19.05 25.4 Roller Dia inner width d1 b1 5 6.35 8.51 10.16 12.07 15.88 3 8.72 5.72 9.65 11.68 17.02 Pitch Roller Dia inner width b1 mm P (mm- inch) d1 mm 9.625 - 3/8 5.08 4.75 12.7 - 1/2 7.92 7.92 15.875 - 5/8 10.16 9.53 19.05 - 3/4 11.91 12.70 Pin Dia d2 2.31 3.28 4.45 5.08 5.72 8.28 Plate height Plate h2 t/T 0.8 1.34 1.6 1.7 1.85 4.09/3.10 Pin Dia d2 mm 3.58 3.96 5.08 5.94 Plate height 7.1 8.26 11.81 14.73 16.13 21.08 h2 mm 8.70 12.07 15.09 18.08 Plate T mm 1.30 1.50 2.06 2.44 Tensile Kn 4.4 8.9 17.8 22.2 28.9 60 Tensile Kn 7.90 13.80 21.80 31.10 Please Note: other sizes maybe available upon request please contact your nearest GBC office. Page 41 AUTOMOTIVE IDLERS & TENSIONERS Part Number Part Part Number Number Part Number Part Number Part Number Part Number GT10010 GT10022 GT10030 GT10031 GT10032 GT10040 GT10050 GT10060 GT10061 GT10070 GT10071 GT10072 GT10080 GT10090 GT10100 GT10101 GT10110 GT10111 GT10120 GT10130 GT10140 GT10150 GT10160 GT10161 GT10170 GT10180 GT10190 GT10240 GT10290 GT10300 GT10321 GT10330 GT10361 GT10510 GT10520 GT20010 GT20020 GT20030 GT20040 GT20050 GT20060 GT20070 GT20090 GT20100 GT20110 GT20120 GT20130 GT20140 GT20150 GT20160 GT30010 GT40010 GT60000 GT60030 GT60040 GT60050 GT60060 GT60070 GT60080 GT60090 GT60100 GT60110 GT60120 GT60130 GT60140 GT60150 GT60160 GT60170 GT60180 GT60190 GT60200 GT60210 GT60220 GT60230 GT60240 GT60250 GT60260 GT60270 GT60280 GT60290 GT60300 GT60320 GT60330 GT60340 GT60350 GT60360 GT60370 GT60380 GT80250 GT80260 GT80270 GT80280 GT80290 GT80300 GT80310 GT80320 GT80330 GT80340 GT80350 GT80360 GT80370 GT80380 GT80390 GT80400 GT80410 GT80420 GT80430 GT80440 GT80450 GT80460 GT80470 GT80480 GT80490 GT80500 GT80510 GT80520 GT80530 GT80540 GT80550 GT80560 GT80570 GT80580 GT80590 GT80600 GT80610 GT80620 GT80630 GT80640 GT80650 GT80660 GT80670 GT80680 GT80690 GT80700 GT80710 GT80720 GT80730 GT80740 GT80750 GT80760 GT80770 GT80780 GT80790 GT80800 GT80810 GT80820 GT80830 GT80840 GT80850 GT80860 GT80870 GT80880 GT80890 GT80900 GT80910 GT80920 GT80930 GT80940 GT80950 GT80960 GT80970 GT80980 GT80990 GT90000 GT90010 GT90020 GT90030 GT90040 GT90050 GT90060 GT90070 GT90080 GT90085 GT90090 GT90100 GT90110 GT90115 GT90120 GT90130 GT90140 GT90150 GT90160 GT90170 GT90180 GT90190 GT90200 GT90210 GT90220 GT90230 GT90240 GT90250 GT90260 GT90270 GT90280 GT90290 GT90300 GT90310 GT90320 GT90330 GT90340 GT90350 GT90360 GT90370 GT90380 GT90390 GT90400 GT90410 GT90420 GT90430 GT90440 GT90450 GT90460 GT90470 GT90480 GT90490 GT90500 GT90510 GT90520 GT90530 GT90540 GT90550 GT90560 GT90570 GT90580 GT90590 GT90600 GT90610 GT90620 GT90630 GT90640 GT90650 GT90660 GT90670 GT90680 GT90690 GT90700 GT90710 GT90720 GT90730 GT90740 GT90750 GT90760 GT90770 GT90780 GT90790 GT90800 GT90810 GT90820 GT90830 GT90840 GT90850 GT90860 GT90870 GT90880 GT90890 GT90900 GT90910 GT90920 GT90930 GT90940 GT90950 GT60390 GT60390 GT60395 GT60400 GT60410 GT60420 GT60430 GT60440 GT60450 GT60460 GT60470 GT60480 GT60490 GT60500 GT60510 GT60520 GT60660 GT80010 GT80010 GT80020 GT80030 GT80040 GT80040 GT80050 GT80060 GT80070 GT80080 GT80090 GT80090 GT80100 GT80110 GT80120 GT80130 GT80140 GT80150 GT80160 GT80170 GT80180 GT80190 GT80200 GT80210 GT80220 GT80230 GT80240 Note: Separate catologue or information sheets with further details on tensioner bearings and engine pulleys are available upon request. Page 42 ENGINE PULLEYS, HUBS, LOCK RINGS Part Number EP001 EP002 EP003 EP004 EP005 EP006 EP007 EP008 EP009 EP010 EP011 EP012 EP013 EP014 EP015 EP016 EP017 EP018 EP019 Part Part Number Number EP024 EP048 EP025 EP049 EP026 EP050 EP027 EP051 EP028 EP052 EP029 EP053 EP030 EP054 EP031 EP055 EP032 EP056 EP033 EP057 EP034 EP058 EP035 EP059 EP036 EP060 EP037 EP061 EP038 EP062 EP039 EP064 EP040 EP065 EP041 EP066 EP046 EP068 Part Number EP069 EP071 EP077 EP078 EP088 EP089 EP094 EP095 EP097 EP101 EP131 EP161 EP163 Retainer Ring (Locking Collar) Part Number Notes 015BR RS40 014-R 06-R/R30J 014-MR 08R-1 C014B C06 M013 R32J Hub Units We supply hub units to suit most Korean manufactured vehicles as well as Ford and Holden models. Other models maybe availableupon request. SEALS Bonded Seals Wiper Seals Mechanical Seals O-Rings We stock a large range of seals too numerous to list in this catalogue Page 43 TOOLS Mini Bearing Puller Item No.: ARX-YC716 Spec: Forcing Screw: 1Pc (φ5/16"-18T x L102mm S45C) Beam: 1Pc Pilot Bearing Puller ARXItem No.: PB1238 Pulling I.D...............12-38mm Main Rod: 2Pcs (8mm x L85mm x 1/4"-20T Hex Bar) Extension Rod: 2Pcs (8mm x L40mm x 1/4"-20T Hex Bar) Bearing Separator: 1Pc Spread Range 10~35mm Jaw: 2Pcs (L82mm) Separator Puller Set Spindle Bearing Puller Item No.: ARX-YC708 Item No.: Spec: ARX-YC0005 1.Jaw Long..............300mm 2.Pulling O.D.........10-44mm 3.Rearching Length......235mm Outer Tie Rod Remover Item No.: ARX-YC0002 Spec: 1.Pulling O.D..................70mm 2.Rearching Length.............75mm 2 & 3 Leg Puller Kits These are general purpose light duty kits for 2 or 3 leg operation Item No.: Seal Puller Item No.: ARX-CJ930 Page 44 ARX-3MPK 3" mechanical puller ARX-4MPK 4" mechanical puller ARX-6MPK 6" mechanical puller TOOLS cont. Separator / Press Plates Item No.: ARX-SP1 10~50mm ARX-SP2 30~70mm ARX-SP3 40~90mm ARX-SP4 55~145mm ARX-SP5 75~210mm Size relates to min & max size of bearing OD plate can accommodate Seal & Cup Driver Item No.: ARX-13K120 Spec: 9 Piec Tapered drift plugs 32mm, 38mm, 42mm, 47mm, 54mm, 62mm, 66mm, 67mm. Measurements taken from bottom of taper. Bushing Remover/Installer Item No.: ARX-BD01 Drift plugs from 3/8" to 1 3/8" 3 x strike rods "C" Clip Plier Item No.: ARX-94006 6 Piece "C" Clip Pliers 12 Point universal tool, 45 & 90 degree . interchangeable heads for rings to 20mm I.D Item No.: IR-090K Stride/Imperial by Milbar USA Contents: IR70,IR7090, IR47, IR4790 IR38, IR3890 External Snap Ring Pliers 2 Piece Ratcheting Kit Multi Tip Flat tips for external clips only Item No.: IR-50K Item No.: Page 45 IR-LRS 340mm (13.5") IR-47R 210mm (8") Reference Tables and Cross overs INCHES FRACTIONAL DECIMAL METRIC INCHES FRACTIONAL DECIMAL mm . 0.0039 0.1000 . 0.0079 . 0.0118 1/64 METRIC mm 27/64 0.4219 10.7156 0.2000 . 0.4331 11.0000 0.3000 7/16 0.4375 11.1125 0.0156 0.3969 . 0.4528 11.5000 . 0.0157 0.4000 29/64 0.4531 11.5094 . 0.0197 0.5000 15/32 0.4688 11.9063 . 0.0236 0.6000 . 0.4724 12.0000 . 0.0276 0.7000 31/64 0.4844 12.3031 1/32 0.0313 0.7938 . 0.4921 12.5000 . 0.0315 0.8000 1/2 0.5000 12.7000 . 0.0354 0.9000 . 0.5118 13.0000 . 0.0394 1.0000 33/64 0.5156 13.0969 13.4938 . 0.0433 1.1000 17/32 0.5313 3/64 0.0469 1.1906 . 0.5315 13.5000 . 0.0472 1.2000 35/64 0.5469 13.8906 . 0.0512 1.3000 . 0.5512 14.0000 . 0.0551 1.4000 9/16 0.5625 14.2875 . 0.0591 1.5000 . 0.5709 14.5000 1/16 0.0625 1.5875 37/64 0.5781 14.6844 . 0.0630 1.6000 . 0.5906 15.0000 . 0.0669 1.7000 19/32 0.5938 15.0813 . 0.0709 1.8000 39/64 0.6094 15.4781 . 0.0748 1.9000 . 0.6102 15.5000 5 16/25 0.0781 1.9844 5/8 0.6250 15.8750 . 0.0787 2.0000 . 0.6299 16.0000 . 0.0827 2.1000 41/64 0.6406 16.2719 . 0.0866 2.2000 . 0.6496 16.5000 . 0.0906 2.3000 21/32 0.6563 16.6688 3/32 0.0938 2.3813 . 0.6693 17.0000 . 0.0945 2.4000 43/64 0.6719 17.0656 . 0.0984 2.5000 11/16 0.6875 17.4625 7/64 0.1094 2.7781 . 0.6890 17.5000 . 0.1181 3.0000 45/64 0.7031 17.8594 1/8 0.1250 3.1750 . 0.7087 18.0000 . 0.1378 3.5000 23/32 0.7188 18.2563 9/64 0.1406 3.5719 . 0.7283 18.5000 5/32 0.1563 3.9688 47/64 0.7344 18.6531 . 0.1575 4.0000 . 0.7480 19.0000 11/64 0.1719 4.3656 3/4 0.7500 19.0500 . 0.1772 4.5000 49/64 0.7656 19.4469 3/16 0.1875 4.7625 . 0.7677 19.5000 . 0.1969 5.0000 25/32 0.7813 19.8438 13/64 0.2031 5.1594 . 0.7874 20.0000 . 0.2165 5.5000 51/64 0.7969 20.2406 7/32 0.2188 5.5563 . 0.8071 20.5000 15/64 0.2344 5.9531 13/16 0.8125 20.6375 . 0.2362 6.0000 . 0.8268 21.0000 1/4 0.2500 6.3500 53/64 0.8281 21.0344 . 0.2559 6.5000 27/32 0.8438 21.4313 17/64 0.2656 6.7469 . 0.8465 21.5000 21.8281 . 0.2756 7.0000 55/64 0.8594 9/32 0.2813 7.1438 . 0.8661 22.0000 . 0.2953 7.5000 7/8 0.8750 22.2250 19/64 0.2969 7.5406 . 0.8858 22.5000 5/16 0.3125 7.9375 57/64 0.8906 22.6219 . 0.3150 8.0000 . 0.9055 23.0000 21/64 0.3281 8.3344 29/32 0.9063 23.0188 . 0.3346 8.5000 59/64 0.9219 23.4156 11/32 0.3438 8.7313 . 0.9252 23.5000 . 0.3543 9.0000 15/16 0.9375 23.8125 23/64 0.3594 9.1281 . 0.9449 24.0000 . 0.3740 9.5000 61/64 0.9531 24.2094 3/8 0.3750 9.5250 . 0.9646 24.5000 25/64 0.3906 9.9219 31/32 0.9688 24.6063 . 0.3937 10.0000 . 0.9843 25.0000 13/32 . 0.4063 0.4134 10.3188 10.5000 63/64 1 0.9844 1.0000 25.0031 25.4000 Page 46 1 Kn = 101.9716 Kilogram Force 1 Bar = 14.5038 PSI 1 Kpa = 0.1450 PSI 1 Kg = 2.2046 lb 1 Kg = 0.1575 Stone 1 Ounce = 28.3495 Gram 1 Meter = 39.37 Inches 1 Yard = 914.399 mm RPM in M/min = 1000 x Vc / TT x D Where TT = Pi Vc = Surface Speed (M/min) D = Diameter RPM in Ft/min = SFM x 3.82 / D Where SFM = Surface Speed (Ft/min) D = Diameter Inch Keyway Nominal Shaft Dia. Upto & Including Over 1/4 1/2 1/2 3/4 3/4 1 1 1 1/4 1 1/4 1 1/2 1 1/2 1 3/4 1 3/4 2 2 2 1/2 2 1/2 3 3 3 1/2 3 1/2 4 4 5 5 6 Metric Keyway Nominal Shaft Dia. Upto & Key Size (WxT) Including Over 10 12 4x4 12 17 5x5 17 22 6x6 22 30 8x7 30 38 10x8 38 44 12x8 44 50 14x9 50 58 16x10 58 65 18x11 65 75 20x12 75 85 22x14 85 95 25x14 95 100 28x16 Key Size 1/8 3/16 1/4 5/16 3/8 7/16 1/2 5/8 3/4 7/8 1 1 1/4 1 1/2 Page 47 I SO Tole r a n ce s for H ole s ( I SO 2 8 6 - 2 ) N om in a l h ole size s ( m m ) ove r in c. 3 6 10 18 30 40 50 65 80 100 120 140 160 180 200 225 250 280 315 355 6 10 18 30 40 50 65 80 100 120 140 160 180 200 225 250 280 315 355 400 m icr om e t r e s E6 E7 E1 1 E1 2 E1 3 F6 F7 F8 G6 G7 G8 H6 H7 H8 H9 H1 0 H1 1 J6 J7 28 34 43 53 66 79 94 110 129 142 161 20 25 32 40 50 60 72 85 100 110 125 32 40 50 61 75 90 107 125 146 162 185 20 25 32 40 50 60 72 85 100 110 125 95 115 142 170 210 250 292 335 390 430 485 20 25 32 40 50 60 72 85 100 110 125 140 175 212 250 300 360 422 485 560 630 695 20 25 32 40 50 60 72 85 100 110 125 200 245 302 370 440 520 612 715 820 920 +1 015 20 25 32 40 50 60 72 85 100 110 125 18 22 27 33 41 49 58 68 79 88 98 10 13 16 20 2 30 36 43 50 56 62 22 28 34 41 50 60 71 83 96 108 119 10 13 16 20 25 30 36 43 50 56 62 28 35 43 53 64 76 90 106 122 137 151 10 13 16 20 25 30 36 43 50 56 62 12 14 17 20 25 29 34 39 44 49 54 4 5 6 7 9 10 12 14 15 17 18 16 20 24 28 34 40 47 54 61 69 75 4 5 6 7 9 10 12 14 15 17 18 22 27 33 40 48 56 66 77 87 98 107 4 5 6 7 9 10 12 14 15 17 18 8 9 11 13 16 19 22 25 29 32 36 0 0 0 0 0 0 0 0 0 0 0 12 15 18 21 25 30 35 40 46 52 57 0 0 0 0 0 0 0 0 0 0 0 18 22 27 33 39 46 54 63 72 81 89 0 0 0 0 0 0 0 0 0 0 0 30 36 43 52 62 74 87 100 115 130 140 0 0 0 0 0 0 0 0 0 0 0 48 58 70 84 100 120 140 160 185 210 230 0 0 0 0 0 0 0 0 0 0 0 75 90 110 130 160 190 220 250 290 320 360 0 0 0 0 0 0 0 0 0 0 0 5 5 6 8 10 13 16 18 22 25 29 -3 -4 -5 -5 -6 -6 -6 -7 -7 -7 -7 6 8 10 12 14 18 22 26 30 36 39 -18 -6 -7 -8 -9 -11 -12 -13 -14 -16 -16 10 12 15 20 24 28 34 41 47 55 60 J8 -8 -10 -12 -13 -15 -18 -20 -22 -25 -26 -29 4 4.5 5.5 6.5 8 9.5 11 12.5 14.5 16 18 JS6 -4 -4.5 -5.5 -6.5 -8 -9.5 -11 -12.5 -14.5 -16 -18 6 7.5 9 10.5 12.5 15 17.5 20 23 26 28.5 JS7 -6 -7.5 -9 -11 -12.5 -15 -17.5 -20 -23 -26 -28.5 9 11 13.5 16.5 19.5 23 27 31.5 36 40.5 44.5 JS8 -9 -11 -14 -19.5 -23 -27 -31.5 -36 -40.5 -44.5 2 2 2 2 3 4 4 4 5 5 7 K6 -6 -7 -9 -11 -13 -15 -18 -21 -24 -27 -29 3 5 6 6 7 9 10 12 13 16 17 K7 -9 -10 -12 -15 -18 -21 -25 -28 -33 -36 -40 5 6 8 10 12 14 16 20 22 25 28 K8 -13 -16 -19 -23 -27 -32 -38 -43 -50 -56 -61 -17 -1 -3 -4 -4 -4 -5 -6 -8 -8 -9 -10 -9 -12 -15 -17 -20 -24 -28 -33 -37 -41 -46 0 0 0 0 0 0 0 0 0 0 0 M7 -12 -15 -18 -21 -25 -30 -35 -40 -46 -52 -57 2 1 2 4 5 5 6 8 9 9 11 M8 -16 -21 -25 -29 -34 -41 -48 -55 -63 -72 -78 -5 -7 -9 -11 -12 -14 -16 -20 -22 -25 -26 N6 -13 -16 -20 -24 -28 -33 -38 -45 -51 -57 -62 -4 -19 -5 -23 -7 -28 -8 -9 -10 -12 -14 -14 -16 N7 -4 -16 -33 -39 -45 -52 -60 -66 -73 M6 Page 48 I SO Tole r a n ce s for H ole s ( I SO 2 8 6 - 2 ) N om in a l h ole size s ( m m ) ove r in c. 3 6 10 18 30 40 50 65 80 100 120 140 160 180 200 225 250 280 315 355 6 10 18 30 40 50 65 80 100 120 140 160 180 200 225 250 280 315 355 400 m icr om e t r e s -2 -3 -3 -3 -3 -4 -4 -4 -5 -5 -5 N8 -20 -25 -30 -36 -42 -50 -58 -67 -77 -86 -94 -9 -12 -15 -18 -21 -26 -30 -36 -41 -47 -51 P6 -17 -21 -26 -31 -37 -45 -52 -61 -70 -79 -87 -8 -9 -11 -14 -17 -21 -24 -28 -33 -36 -41 -20 -24 -29 -35 -42 -51 -59 -68 -79 -88 -98 -12 -15 -18 -22 -26 -32 -37 -43 -50 -56 -62 -30 -37 -45 -55 -65 -78 -91 -106 -122 -137 -151 P7 P8 -12 -16 -20 -24 -29 -35 -37 -44 -47 -56 -58 -61 -68 -71 -75 -85 -89 -97 -103 R6 -20 -25 -31 -37 -45 -54 -56 -66 -69 -81 -83 -86 -97 -100 -104 -117 -121 -133 -139 -13 -28 -16 -34 -20 -41 -25 R7 -11 -23 -30 -60 -32 -62 -38 -73 -41 -76 -48 -88 -50 -90 -53 -93 -60 -106 -63 -109 -67 -113 -74 -126 -78 -130 -87 -144 -93 -150 -50 I SO Tole r a n ce s for Sh a ft s ( I SO 2 8 6 - 2 ) N om in a l Sh a ft Size s ( m m ) ove r in c. 3 6 10 18 30 40 50 65 6 10 18 30 40 50 65 80 100 120 140 160 180 200 225 250 280 315 355 100 120 140 160 180 80 200 225 250 280 315 355 400 - 270 - 280 - 290 - 300 - 310 - 320 - 340 - 360 - 380 - 410 - 460 - 520 - 580 - 660 - 740 - 820 - 920 - 1050 - 1200 - 1350 m icr om e t r e s a1 2 d6 e6 e1 3 f5 f6 f7 - 390 - 430 - 470 - 510 - 560 - 570 - 640 - 660 - 730 - 760 - 860 - 920 - 980 - 1120 - 1200 - 1280 - 1440 - 1570 - 1770 - 1920 - 30 - 40 - 50 - 65 - 80 - 100 - 120 - 145 - 170 - 190 - 210 - 38 - 49 - 61 - 78 - 96 - 119 - 142 - 170 - 199 - 222 - 246 - 20 - 25 - 32 - 40 - 50 - 60 - 72 - 85 - 100 - 110 - 125 - 28 - 34 - 43 - 53 - 66 - 79 - 94 - 110 - 129 - 142 - 161 - 50 - 60 - 72 - 85 - 100 - 110 - 125 - 440 - 520 - 612 - 715 - 820 - 920 - 1015 - 25 - 30 - 36 - 43 - 50 - 56 - 62 - 220 - 270 - 334 - 410 - 25 - 32 - 40 - 49 - 36 - 43 - 51 - 61 - 70 - 79 - 87 - 10 - 13 - 16 - 20 - 25 - 30 - 36 - 43 - 50 - 56 - 62 - 18 - 22 - 27 - 33 - 41 - 49 - 58 - 68 - 79 - 88 - 98 - 10 - 13 - 16 - 20 - 25 - 30 - 36 - 43 - 50 - 56 - 62 - 22 - 28 - 34 - 41 - 50 - 60 - 71 - 83 - 96 - 108 - 119 -4 -5 -6 -7 -9 - 10 - 12 - 14 - 15 - 17 - 18 -9 - 11 - 14 - 16 - 20 - 23 - 27 - 32 - 35 - 40 - 43 -4 -5 -6 -7 -9 - 10 - 12 - 14 - 15 - 17 - 18 - 12 - 14 - 17 - 20 - 25 - 29 - 34 - 39 - 44 - 49 - 54 -4 -5 -6 -7 -9 - 10 - 12 - 14 - 15 - 17 - 18 - 16 - 20 - 24 - 28 - 34 - 40 - 47 - 54 - 61 - 69 - 75 0 0 0 0 0 0 0 0 0 0 0 h4 -4 -4 -5 -6 -7 -8 - 10 - 12 - 14 - 16 - 18 0 0 0 0 0 0 0 0 0 0 0 h5 -5 -6 -8 -9 - 11 - 13 - 15 - 18 - 20 - 23 - 25 0 0 0 0 0 0 0 0 0 0 0 h6 -8 -9 - 11 - 13 - 16 - 19 - 22 - 25 - 29 - 32 - 36 0 0 0 0 0 0 0 0 0 0 0 h7 - 12 - 15 - 18 - 21 - 25 - 30 - 35 - 40 - 46 - 52 - 57 0 0 0 0 0 0 0 0 0 0 0 h8 - 18 - 22 - 27 - 33 - 39 - 46 - 54 - 63 - 72 - 81 - 89 0 0 0 0 0 0 0 0 0 0 0 h9 - 30 - 36 - 43 - 52 - 62 - 74 - 87 - 100 - 115 - 130 - 140 0 0 0 0 0 0 0 0 0 0 0 h1 0 - 48 - 58 - 70 - 84 - 100 - 120 - 140 - 160 - 185 - 210 - 230 0 0 0 h1 1 - 75 g5 g6 g7 0 0 h1 2 - 90 - 110 - 130 0 0 0 - 120 - 150 - 180 - 210 0 0 0 0 0 0 0 - 160 - 190 - 220 - 250 - 290 - 320 - 360 0 0 0 0 0 0 0 - 250 - 300 - 350 - 400 - 460 - 520 - 570 3 4 5 5 6 6 6 7 7 7 7 j5 -2 -2 -3 -4 -5 -7 -9 - 11 - 13 - 16 - 18 6 -2 7 -2 8 -3 9 -4 11 12 13 14 16 16 18 j6 -5 -7 -9 - 11 - 13 - 16 - 18 Page 49 I SO Tole r a n ce s for Sh a ft s ( I SO 2 8 6 - 2 ) N om in a l Sh a ft Size s ( m m ) ove r in c. 3 6 10 18 30 40 50 65 6 10 18 30 40 50 65 80 100 120 140 160 180 200 225 250 280 315 355 100 120 140 160 180 80 200 225 250 280 315 355 400 m icr om e t r e s 8 10 12 13 15 18 20 22 25 26 29 j7 -4 -5 -6 -8 - 10 - 12 - 15 - 18 - 21 - 26 - 28 2.5 - 2.5 3 -3 4 -4 4.5 - 4.5 5.5 6.5 7.5 9 10 11.5 12.5 j s5 - 5.5 - 6.5 - 7.5 -9 - 10 - 11.5 - 12.5 4 4.5 5.5 6.5 8 9.5 11 12.5 14.5 16 18 j s6 -4 - 4.5 - 5.5 - 6.5 -8 - 9.5 - 11 - 12.5 - 14.5 - 16 - 18 6 7.5 9 11 12.5 15 17.5 20 23 26 28.5 j s7 -6 - 7.5 -9 - 11 - 12.5 - 15 - 17.5 - 20 - 23 - 26 - 28.5 6 7 9 11 13 15 18 21 24 27 29 1 1 1 2 2 2 3 3 4 4 4 9 10 12 15 18 21 25 28 33 36 40 k5 k6 k7 m5 m6 1 1 1 2 2 2 3 3 4 4 4 13 16 19 23 27 32 38 43 50 56 61 1 1 1 2 2 2 3 3 4 4 4 9 12 15 17 20 24 28 33 37 43 46 4 6 7 8 9 11 13 15 17 20 21 12 15 18 21 25 30 35 40 46 52 57 4 6 7 8 9 11 13 15 17 20 21 16 21 25 29 34 41 48 55 63 72 78 4 6 7 8 9 11 13 15 17 20 21 13 16 20 24 28 33 38 45 51 57 62 8 10 12 15 17 20 23 27 31 34 37 16 19 23 28 33 39 45 52 60 66 73 8 10 12 15 17 20 23 27 31 34 37 20 25 30 36 42 50 58 67 77 86 94 8 10 12 15 17 20 23 27 31 34 37 17 21 26 31 37 45 52 61 70 79 87 12 15 18 22 26 32 37 43 50 56 62 20 24 29 35 42 51 59 68 79 88 98 p6 12 15 18 22 26 32 37 43 50 56 28 19 34 23 41 28 50 r6 23 15 m7 n5 n6 n7 p5 34 60 41 62 43 73 51 76 54 88 63 90 65 Radial Clearance Bore C2 STD C3 2.5 - 10 0 -7 2 -13 8 -23 C4 -- CM -- 10 - 18 0 -9 3 -18 11 -25 18 -33 4 -11 18 - 24 0 -10 5 -20 13 -28 20 -36 5 -12 24 - 30 0 -11 5 -20 13 -28 23 -41 5 -12 30 - 40 0 -11 6 -20 15 -33 28 -46 9 -17 40 - 50 0 -11 6 23 18 -36 30 51 9 -17 50 - 65 0 -15 8 -28 23 -43 38 -61 12 -22 65 - 80 0 -15 10 -30 25 -51 46 -71 12 -22 80 - 100 0 -18 12 -36 30 -58 53 -84 18 -30 Page 50 93 68 106 77 109 80 113 84 126 94 62 130 98 144 108 150 114 Conversion Charts GBC UC UCX SB SA HC UR CSA SC SER UK UKX ------- NTN UC CX AS AEL UEL ---AELS CS UCS UK UKX UELS ---- NSK UC UCX UB EN EW UR ENR ---UR..NDG UK UKX EWR UBR TRANSMISSION BEARINGS NACHI ASAHI SKF KOYO UC UC YAR UC UCX UCX UCX UCX ---B UB SB SA KH YET SA NA UG or FG YEL NA ---------RB ---KHR ENR SAA ------------ER SER ER ER UK UK UK UK UKX UKX UKX UKX ------EWR ---B ---UBR SBB GBC C F FA FB FC FCX FL FLX FX HA LF P PA PH PX T ---SB NTN C F FA FH FC FCX FL FLX FX HB FB P UP HP PX T ---SB NSK C F FA FK FC FCX FL FLX FX EH LFL P PA PH PX T WB SB TRANSMISSION HOUSINGS NACHI ASAHI SKF KOYO C C C C F F FY F FA FA FA FA FK FK FK FB FC FC FC FC FCX FCX FCX FCX FL FL FYTB FL FLX FLX ---FLX FX FX FX FX ---ECH ECH HA LF LFL LF LF P P SY P PA PA PA PA PH PH PH PH PX PX PX PX T T TU T ---WB ---TH SB SB SB SB NOTES SPHER. OD, SCREW SPHER. OD, SCREW SPHER. OD, SCREW SPHER. OD, COLLAR SPHER. OD, COLLAR CYL. OD, SCREW CYL. OD, COLLAR CYL OD, SNAP GROOVE CYL OD, SNAP GROOVE, SCREW SPHER.OD, TAPER BORE SPHER.OD, TAPER BORE CYL OD, SNAP GROOVE, COLLAR CYL. OD SCREW NOTES CARTRIDGE SQUARE FLANGE 4 BOLT ADJUSTABLE ANGLE FLANGE OFFSET FLANGE ROUND FLANGE 4 BOLT MED. DUTY RND. FLANGE 4 BOLT FLANGE 2 BOLT MED. DUTY FLANGE 2 BOLT MED. DUTY SQR. FLANGE 4 BOLT HANGER HOUSING SMALL FLANGE 2 BOLT PILLOW BLOCK PILLOW, TAPPED BASE ELEVATED PILLOW BLOCK MED. DUTY PILLOW BLOCK TAKE-UP UNIT TAKE-UP FRAME SAW BENCH PRESSED METAL HOUSINGS GBC PP203 PP204 PP205 PP206 PP207 BALMIC 40PB 47PB 52PB 62PB 72PB GBC PFL203 PFL204 PFL205 PFL206 PFL207 BALMIC 40MST 47MST 52MST 62MST 72MST Page 51 GBC PF203 PF204 PF205 PF206 PF207 PF208 PF209 PF210 PF210 BALMIC 40MS 47MS 52MS 62MS 72MS 80MS 85MS 87MS (SQ) 100MS SPHERICAL PLAIN BEARINGS INA SKF GBC IKO ELGES GE..ES GEG..ES GEZ..ES GEEM..ES GEEW..ES GE..ET GE..XT GEBK..S GE..ES GE..GS SBB ------GE..EC ---PB… GE..DO GE..FO GE..ZO GE..HO GE..LO GE..UK GE..UK ---- GE..DO GE..FO GE..ZO ---------------- GBC IKO ELGES INA SIBP..S SABP..S SILBP..S SALBP..S SIZP..S SAZP..S SALZP..S SILZP..S SIJK..C SAJK..C SIBK..S SABK..S GE..ES GEH..ES GEZ..ES GEM..ES GEG..ES GE..TE GE..TA ---- ROD ENDS SKF PHS.. GIKFR.. GIR.. SIKAC.. POS.. GAKFR.. GAR.. SAKAC.. PHS..L GIKFL.. GIL.. SILKAC.. POS..L GAKFL.. GAL.. SALKAC.. PHSB.. ---------POSB.. ---------PHSB..L ---------POSB..L ------------GIR..UK ---SI..C ---GAR..UK ---SA..C ---GIKFR..PW GIKFR..PB SIKB..F ---GAKFR..PW GAKFR..PB SAKB..F Page 52 NOTES STND.,LUBE RE-LUBE,METRIC MED.DUTY,RE-LUBE & GROOVE, METRIC STND.,LUBE RE-LUBE,IMPERIAL WIDER INNER RING, RE-LUBE,METRIC WIDE INNER RING, RE-LUBE,METRIC STND.,PTFE LINED, METRIC UP TO GE120 STND.,PTFE LINED, METRIC FROM GE140 INLAID LINER, CHROME PLATED, METRIC NOTES BRONZE LINED, FEMALE RH, METRIC BRONZE LINED, MALE RH, METRIC BRONZE LINED, FEMALE LH, METRIC BRONZE LINED, MALE LH, METRIC BRONZE LINED, FEMALE RH, IMPERIAL BRONZE LINED, MALE RH, IMPERIAL BRONZE LINED, MALE LH, IMPERIAL BRONZE LINED, FEMALE LH, IMPERIAL HARD CHROME/PTFE COMP. MATERIAL HARD CHROME/PTFE COMP. MATERIAL ALUMIN.-BRONZE LINER/CHROME PLATED ALUMIN.-BRONZE LINER/CHROME PLATED
Similar documents
Bearings - Turfmaster
A 1 3/8 B 3/4 Exterior appears similar to
low-speed bearings, but is constructed with
deep groove, case hardened outer race for
heavier weight capacity. Fits Case, Cub Cadet
& Dixon 30" & 40" cut d...
MAHLE Valvulas Argentina 2014.indd
4988G - Catálogo Válvulas - Miolo ES-EN.indd 10
