Clutch

Transcription

Clutch
CLUTCHES
Table of Contents
Basic Clutch Information
Guide to Clutch Identification and Catalog Use
In our efforts to make this catalog as complete and as useful as possible, clutches
are listed in three different sections.
1. Specifications Section (listed in ascending order by diameter)
2. Illustration or Photo Section (listed in our numeric order within by manufacturer)
3. Cross Reference Section (OEM service numbers and/or numbers stamped on
the clutch are listed in the cross reference section in the back of this catalog)
The clutch used on a particular truck depends on the type of compressor selected from an
option list when the truck was first assembled. However, after miles of service, original
parts most likely have been replaced. For whatever reason, a truck originally equipped
with a reciprocating compressor may now be using a rotary type or possibly a single
groove clutch has been replaced with a double groove. To assure your customer gets the
right part the first time, it is important to identify the compressor the clutch is to be used
on, and the characterisitics or specifications of the clutch. If possible, check for label or
stamped numbers on the clutch body or the coil assembly to identify the clutch.
If the clutch marking or lable is illegible, the following information will be needed:
1. Compressor Make and Model
2. Voltage - 12v or 24v
3. Diameter of Clutch Pulley
4. Number of Grooves; Width of Drive Belt
5. A-B Distance or Gauge Line
CLUTCHES
For your convenience, a “How to Measure” is shown in each clutch section to help in identification.
Clutches are listed in alphabetical sequence by the name of the compressor manufacturer the clutch is to be installed on.
CLUTCHES
CCI (SEE T/CCI) ................................... 197
DENSO ................................................. 201
FORD .................................................... 203
SANDEN ............................................... 204
SELTEC/VALEO ................................... 211
TAMA HD (see Seltec/Valeo)
T/CCI, YORK STYLE ............................ 197
Clutch Related Items
Clutch Coils
Denso ..................................................... 202
Sanden ................................................... 204
Seltec/Valeo ........................................... 211
Clutch Plate Removal Tools ......................... 520
Clutch Pulley/Pullers ..................................... 520
Connectors and Pigtails ................................ 493
Idler Pulleys and Eccentrics ......................... 424
196
© 2011 MEI Corporation
T/CCI (York Style) — CLUTCHES
Groove
Width
HOW TO MEASURE CLUTCH: T/CCI (YORK STYLE)
m
o
IF PART NUMBER ON CLUTCH BEING REPLACED CANNOT BE READ,
USE THE FOLLOWING PROCEDURE TO DETERMINE REQUIRED
CLUTCH PART NUMBER.
Diameter
1. DETERMINE IF 12 OR 24 VOLT (Black Wire = 12V, Green Wire = 24V).
2. DETERMINE IF CLUTCH IS SINGLE, DOUBLE OR POLY GROOVE.
E
3. MEASURE OUTSIDE DIAMETER OF PULLEY.
A-B
Distance
4. MEASURE WIDTH OF PULLEY GROOVE:
a. Single and Double Groove = measure the width of pulley groove.
b. Poly Groove = count the number of grooves.
Belt Width
(Rear)
m
o
Diameter
5. MEASURE ACCURATELY THE A-B DISTANCE:
a. Single and Double Groove = measure the distance from the compressor
mounting hole on the side of the compressor to the middle of the rear belt
groove on the pulley (the rear belt groove is closest to the compressor).
b. Poly Groove = measure the distance from the compressor mounting hole
on the side of the compressor to the middle of the first groove on the pulley.
6. DETERMINE THE NUMBER OF WIRES.
E
To convert millimeters to inches: divide mm by 25.4
To convert inches to mm: multiply inches by 25.4
A-B
Distance
CLUTCHES
T/CCI (YORK STYLE) 12 volt unless noted
Clutches are listed in ascending order by grooves, by diameter (O.D), by part number.
No. of
Grv’s
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
6
6
6
6
8
8
CLUTCH
O.D.
PART NO.
6"
5011
6"
5031
6"
5125
6"
5131
6-5/16"
5032
6-5/16"
5009
6-3/4"
5033
6-3/4"
5096
6-3/4"
5036
6-3/4"
5062
6-3/4"
5038
7-5/16"
5063
6"
5143
6"
5045
6"
5144
6"
5145
6"
5044
7"
5141
7"
5042
7"
5041
5.8"
5030
6"
5129
6" FF Style 5127
6" FF Style 5126
5.3"
5029
6-5/16"
5128
TECH
TIP
© 2011 MEI Corporation
BELT GROOVE WIDTH
1st grv.
2nd grv.
1/2"
—
1/2"
—
1/2"
—
1/2"
—
5/8"
—
1/2"
—
1/2"
—
1/2"
—
5/8"
—
5/8"
—
5/8"
—
3/4"
—
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
6 Grooves
—
6 Grooves
—
6 Grooves
—
6 Grooves
—
8 Grooves
—
8 Grooves
—
MOUNTING DISTANCE
FIRST
SECOND
2-5/8"
—
2-3/4"
—
2-3/4"
—
2-3/4"
—
2 3/4"
—
2-15/16"
—
3-3/16"
—
2-3/4"
—
1-13/16"
—
1-15/16"
—
2-3/4"
—
2"
—
2-1/8"
2-3/4"
1-11/16"
2-5/16"
1-11/16"
2-5/16"
1-11/16"
2-5/16"
1-11/16"
2-5/16"
1-11/16"
2-5/16"
1-11/16"
2-5/16"
1-11/16"
2-5/16"
2-1/8” Center Point
2-1/8” Center Point
2-3/8” Center Point
2-3/8” Center Point
1-5/8”
1-5/8”
NOTE
w/O.E. style diode & weatherpak conn.
2 wire coil
24 volt
w/O.E. style diode & weatherpak conn.
2 wire plug, Metripak w/diode
Std duty w/single row bearing.
Heavy duty bearing.
24 volt
Std duty w/single row bearing.
1 wire
2 wire plug Metripak
1 wire, Front Forward
2 wire w/diode, Front Forward
1 wire
2 wire plug Metripak w/diode
T/CCI - 2 WIRE METRIPAK CONNECTORS w/DIODE
DO NOT REVERSE
Green wire = positive
White wire = ground
197
CLUTCHES — T/CCI (York Style)
Listed in ascending order by part number.
ile
Wh lies
p
5009
Sup a s t
L
OE# 1406-70
ile
Wh lies
p
5011
Sup a s t
L
OE# 1436-90
Volt - 12V
Dia. - 6 5/16"
Grooves - 1
Width - 1/2"
A-B Dist.- 2 15/16"
Volt - 12V
Dia. - 6"
Grooves - 1
Width - 1/2"
A-B Dist.- 2 5/8"
5030
OE# 513352, MAN-03
Volt - 12V
Dia.- 5.8"
Grooves - Poly 6
Width-.14"
1 Wire
A-B Dist.- 2 1/8" center IHC Plug
CLUTCHES
1 Wire Plug
5029
OE# 515376, MAN-03
Volt - 12V
Dia. - 5.3"
Grooves - Poly 8
Width - .14"
1 Wire
1 Wire Plug A-B Dist.- 1 5/8"
IHC Plug
5031
OE# 502409
Volt - 12V
Dia. - 6"
Grooves - 1
Width - 1/2"
A-B Dist.- 2 3/4”
1 Wire Plug
Weatherpak
5032
OE# 503879, 515528,
MAN-06
Volt - 12V
Dia. - 6 5/16”
Grooves - 1
1 Wire
Width - 5/8"
IHC Plug
A-B Dist.- 2 3/4”
5033
OE# 502740
Volt - 12V
Dia. - 6 3/4"
Grooves - 1
Width - 1/2"
A-B Dist.- 3 3/16"
5036
OE# 502731
Volt - 12V
Dia. - 6 3/4"
Grooves - 1
Width - 5/8"
1 Wire Plug A-B Dist.- 1 13/16"
1 Wire Plug
Groove
Width
Diameter
A-B
Distance
5038
OE# 502743
Volt - 12V
Dia. - 6 3/4"
Grooves - 1
Width - 5/8"
A-B Dist.- 2 3/4"
198
ile
Wh lies
p
Sup a s t
L
1 Wire Plug
Belt
Width
5041
OE# 332334, 502742,
MAN-7A
Volt - 12V
Dia. - 7"
Grooves - 2
Width - 1/2"
A-B Dist.- 1 11/16" / 2 5/16" 1 Wire
5042
OE# 1411-51
Volt - 24V
Dia. - 7"
Grooves - 2
Width - 1/2"
1 Wire
A-B Dist.- 1 11/16" / 2 5/16" Plug
Diameter
A-B
Distance
© 2011 MEI Corporation
T/CCI (York Style) — CLUTCHES
Listed in ascending order by part number (continued).
5045
OE# 1411-35
Volt - 24V
Dia. - 6"
Grooves - 2
Width - 1/2"
A-B Dist.- 1 11/16" / 2 5/16" 1 Wire
5096
OE# 1406-23, CH4.91G
Volt - 12V
Dia. - 6 3/4"
Grooves - 1
Width - 1/2"
A-B Dist.- 2 3/4"
1 Wire Plug
5125
OE# 14533
Volt - 12V
Dia. - 6"
Grooves - 1
Width - 1/2"
A-B Dist.- 2 3/4"
ile
Wh lies
p
p
Su a s t
L
5062
OE# 502733
Volt - 12V
Dia. - 6 3/4"
Grooves - 1
Width - 5/8"
A-B Dist.- 1 15/16"
5063
OE# 502400
Volt - 12V
Dia. - 7 5/16"
Grooves - 1
Width - 3/4"
1 Wire Plug A-B Dist.- 2"
1 Wire Plug
CLUTCHES
5044
OE# 332639,
MAE-6AR, MA-6A
Volt - 12V
Dia. - 6"
Grooves - 2
1 Wire
Width - 1/2"
A-B Dist.- 1 11/16" / 2 5/16"
FF Style
5126
OE# 14432
Volt - 12V
Dia. - 6"
Grooves - Poly 6
2 Wire Plug Width - .14"
2 Wire Plug
Metripak A-B Dist.- 2 3/8" center w/diode
FF Style
5127
OE# 14304
Volt - 12V
Dia. - 6"
1 Wire Plug
Grooves - Poly 6
Weatherpak
Width - .14"
A-B Dist.- 2 3/8" center
Groove
Width
Diameter
A-B
Distance
Belt
Width
5128
OE# 14372
Volt - 12V
Dia. - 6 5/16"
Grooves - Poly 8
Width - .14"
A-B Dist.- 1 5/8"
© 2011 MEI Corporation
2 Wire Plug
Metripak
5129
OE# 14565
Volt - 12V
Dia. - 6"
Grooves - Poly 6
Width - .14"
2 Wire Plug
A-B Dist.- 2 1/8" center w/diode
5131
OE# 508888, MAM-13
Volt - 12V
Dia. - 6"
Grooves - 1
Width - 1/2"
1 Wire
A-B Dist.- 2 3/4"
IHC Plug
Diameter
A-B
Distance
199
CLUTCHES — T/CCI (York Style)
Listed in ascending order by part number (continued).
5141
OE# 511199, MAN-01
Volt - 12V
Dia. - 7"
1 Wire
Grooves - 2
IHC Plug
Width - 1/2"
A-B Dist.- 1 11/16" / 2 5/16"
5143
OE# 7925
Volt - 12V
Dia. - 6"
Grooves - 2
Width - 1/2"
A-B Dist.- 2 1/8" / 2 3/4"
5144
OE# 501939, 024-21590
Volt - 12V
Dia. - 6"
1 Wire Plug
Grooves - 2
Weatherpak
1 Wire Width - 1/2"
IHC Plug A-B Dist.- 1 11/16" / 2 5/16"
5145
OE# 024-25238
Volt - 12V
Dia. - 6"
Grooves - 2
2 Wire Plug
Metripak
Width - 1/2"
A-B Dist.- 1 11/16" / 2 5/16"
CLUTCHES
Groove
Width
Diameter
A-B
Distance
Belt
Width
5589
Clutch Measuring Tool
Servicing Clutch
• Clutch mounting bolts (4):
use torque wrench 13 - 19 ft. lbs.
• Center bolt:
use torque wrench 20 - 25 ft. lbs.
200
5538
Tecumseh/York Style
Compressor Shaft Key
(10 per box)
Diameter
A-B
Distance
© 2011 MEI Corporation
DENSO — CLUTCHES
A-B
Distance
A-B
Distance
A-B
Distance
HOW TO MEASURE CLUTCH: DENSO
Clutch
Diameter
A-B DISTANCE - Measure from the
center of the nearest mounting hole on
compressor to middle of groove (1st
groove if Serpentine).
Clutch
Diameter
10PA15C / 10PA17C / 10S17C
6E171
CLUTCHES USED w/DENSO 10PA15C, 10PA17C COMPRESSORS
Clutches are listed in ascending order by grooves, by diameter (O.D), by part number.
1
1
1
1
1
1
1
1
1
8
8
8
8
8
8
Clutch O.D.
Model
137mm 5.39”
146mm 5.75"
146mm 5.75"
146mm 5.75"
146mm 5.75"
146mm 5.75"
146mm 5.75"
152mm 6.0"
152mm 6.0"
124.5mm 4.9"
124.5mm 4.9"
136mm 5.35"
143mm 5.62”
145mm 5.70"
145mm 5.70"
10S17C
10PA17C
10PA17C
10PA17C
10PA17C
6E171
6E171
10PA15C
10PA17C
10PA15C
10PA17C
10PA17C
10S17C
10PA17C
10PA17C
Part No.
5027G
5020
5019
5017
5018
5027K
5027S
5026
5021
5022
5025
5023A
5028G
5024
5023
A-B Dist
2.7”
1-3/8”
1-5/8”
1-5/16”
2-1/8”
1-7/8”
1-7/8”
2”
1-3/4”
1”
1-7/16” 12
1-7/16” 24
2.45”
1-7/16” 12
1-7/16” 24
Volt
24
12
12
24
12
12
12
24
12
12
—
—
24
—
—
Repl.
Coil
Dust
Cover
—
—
—
—
—
—
—
—
—
—
5669S
5669D
—
5669S
5669S
—
5669D
5669D
5669D
5669D
—
—
—
5669D
—
—
5837
—
5832/5479
5831/5469
Fits Comp.
5844G
5836
5833
5834
5830
5845 (keyed)
5845 (splined)
5843G
5842G
5835
5848G
Listed in ascending order by part number. NOTE: CLUTCHES SUPPLIED WITH COIL, W/O DUST COVER)
RECESSED HUB
5018
10PA17C Volt - 12v
Dia. - 146mm/5.75”
Grooves - 1
A-B Dist. - 2-1/8”/32.5mm
5019
10PA17C Volt - 12v
Dia. - 146mm/5.75”
Grooves - 1
A-B Dist. - 1-5/8”/14mm
RECESSED HUB
5020
10PA17C Volt - 12v
Dia. - 146mm/5.75”
Grooves - 1
A-B Dist. - 1-3/8”/14mm
USED ON COMPRESSORS:
USED ON COMPRESSOR:
5834, TY6783
5830, RE64024
USED ON COMPRESSORS:
5833, TY6626, TY6765
5836, TY6784
5017
10PA17C Volt - 24v
Dia. - 146mm/5.75”
Grooves - 1
A-B Dist. - 1-5/16”/14mm
© 2011 MEI Corporation
USED ON COMPRESSORS:
201
CLUTCHES
No. of
Grv’s
CLUTCHES — DENSO
Listed in ascending order by part number. NOTE: CLUTCHES SUPPLIED WITH COIL, W/O DUST COVER)
5021
10PA17C Volt - 12v
Dia. - 152mm/6.0”
Grooves - 1
A-B Dist. - 1-3/4”/27mm
5022
10PA15C Volt - 12v
Dia. - 124.5mm/4.90”
Grooves - 8
A-B Dist. - 1.0”/18.26mm
5023
10PA17C Volt - 24v
Dia. - 145mm/5.70”
Grooves - 8
A-B Dist. - 1-7/16”/29mm
5023A
10PA17C Volt - 24v
Dia. - 136mm/5.35”
Grooves - 8
A-B Dist. - 1-7/16”/29mm
USED ON COMPRESSORS:
USED ON COMPRESSOR:
5835, AL78779
USED ON COMPRESSOR:
5831, 5469, AT168543
USED ON COMPRESSOR:
5842G, AT215510
5024
10PA17C Volt - 12v
Dia. - 145mm/5.70”
Grooves - 8
A-B Dist. - 1-7/16”/29mm
5025
10PA17C Volt - 12v
OE# RE52508
Dia. - 124.5mm/4.90”
Grooves - 8
A-B Dist. - 1-7/16”/29mm
5026
10PA15C Volt - 24v
Dia. - 152mm/6.0”
Grooves -1 (belt 5/8”)
A-B Dist. - 2.0"/50.8mm
5027G
10S17C Volt - 24
Dia. - 137mm / 5.39”
Grooves - 1
A-B Dist. - 2.7” / 68.5mm
CLUTCHES
5837
USED ON COMPRESSOR:
USED ON COMPRESSOR:
USED ON COMPRESSOR:
USED ON COMPRESSOR:
5832, 5479
TY6764, RE52454
5843G
5844G
5669D
10PA17C Replacement Dust
Cover, Deep Dish Type
7/8” thick, for 1 groove.
5027K KEYED / OE Style
5027S SPLINED / Aftermarket Style
6E171
Volt - 12v
Dia. - 146mm /5.75”
Grooves - 1
A-B Dist. - 1-7/8”
5028G
10S17C Volt - 24
Dia. - 143mm / 5.62”
Grooves - 8
A-B Dist. - 2.45” / 62.2mm
USED ON COMPRESSOR:
USED ON COMPRESSOR:
5845
5848G
202
5023C
Denso Clutch Coil, 24 volt
10PA15C /10PA17C
5669S
10PA17C Replacement Dust
Cover, Shallow Type
5/16” thick, for 8 groove.
© 2011 MEI Corporation
FORD — CLUTCHES
A-B
HOW TO MEASURE CLUTCH: FORD
IF PART NUMBER ON CLUTCH BEING REPLACED CANNOT BE READ,
USE THE FOLLOWING PROCEDURE TO DETERMINE REQUIRED
CLUTCH PART NUMBER.
1. DETERMINE IF 12 OR 24 VOLT.
2. DETERMINE IF CLUTCH IS SINGLE, DOUBLE OR MULTI-GROOVE.
Diameter
3. MEASURE OUTSIDE DIAMETER OF PULLEY.
4. MEASURE WIDTH OF PULLEY GROOVE.
5. MEASURE ACCURATELY THE A-B DISTANCE.
To convert millimeters to inches: divide mm by 25.4
To convert inches to mm: multiply inches by 25.4
Groove
No. of
Grv’s
1
1
6
6
6
7
8
CLUTCH
O.D.
PART NO.
BELT GROOVE WIDTH
1st grv.
MOUNTING DISTANCE
FIRST
NOTE
5-7/8"
5-15/16"
4-7/8"
5"
5-5/8"
4-1/2"
4-1/2"
5074
5075
5072
5080
5081
5082
5102
7/16"
7/16"
1/8”
1/8”
1/8”
1/8”
1/8”
7/8"
1-3/8"
Serpentine
Serpentine
Serpentine
Serpentine
-
FS6 (1)
FS6 (2)
FS6
FS10, Unidamp, 21 Spline
FS10, Unidamp, 21 Spline
FS10, Unidamp, 21 Spline
Ford E-Series, Scroll, Diesel
belt
belt
belt
belt
CLUTCHES
CLUTCHES USED w/FORD FS6 / FS10 (FX15) / SCROLL COMPRESSORS (12 volt unless noted)
(1) CAN USE ON 2 GR. APPL. IF ONLY USING INSIDE GROOVE
(2) CAN USE ON 2 GR. APPL. IF ONLY USING OUTSIDE GROOVE
5072
FS6
OE# 1413-99
Volt - 12V
Dia. - 4 7/8"
Grooves - Poly 6 Width - 1/8"
5074
FS6 (1)
OE# 1413-89, E8DZ-2987A
Volt - 12V
Dia. - 5 7/8"
Grooves - 1
Width - 7/16"
A-B Dist.- 7/8"
5075
FS6 (2)
OE# 1413-88
Volt - 12V
Grooves - 1
A-B Dist.- 1 3/8"
Dia. - 5 15/16"
Width - 7/16"
5080
FS10, 21 Spline Shaft
OE# 1416-17
Volt - 12V
Dia. - 5"
Grooves - Poly 6 Width - 1/8"
A-B Dist. 3/4"
Compressor Shaft Key
5081
FS10, FX15, 21 Spline Shaft
OE# 02-0421
Volt - 12V
Dia. - 5 5/8"
Grooves -Poly 6 Width - 1/6"
A-B Dist. 3/4"
© 2011 MEI Corporation
5082
FS10, FX15, 21 Spline Shaft
OE# 02-0426
Volt - 12V
Dia. - 4 1/2"
Grooves - Poly 7 Width - 1/8"
A-B Dist. 7/8"
5102
OE# YB591, YB627, YB3064
Ford Scroll
E-Series, Diesel
Dia. - 4 1/2"
Grooves - 8
Width - 1/8"
5539
FORD - Compressor Shaft Key
(10 per box)
203
CLUTCHES — SANDEN
Gauge Line
(A-B) Distance
HOW TO MEASURE CLUTCH: SANDEN
IF PART NUMBER ON CLUTCH BEING REPLACED CANNOT
BE READ, USE THE FOLLOWING PROCEDURE TO DETERMINE
REQUIRED CLUTCH PART NUMBER.
Diameter
Groove
Width
1.
2.
3.
4.
5.
DETERMINE IF 12 OR 24 VOLT.
DETERMINE IF CLUTCH IS SINGLE, DOUBLE OR MULTI-GROOVE.
MEASURE OUTSIDE DIAMETER OF PULLEY.
MEASURE WIDTH OF PULLEY GROOVE.
MEASURE ACCURATELY THE A-B DISTANCE.
To convert millimeters to inches: divide mm by 25.4
To convert inches to mm: multiply inches by 25.4
CLUTCHES
SANDEN SD7H15 - CLUTCH HUB IDENTIFICATION
Holes
Not Threaded
Holes
Threaded
Key Shaft Armature Plate
• Keyed shaft can be identified by the
threaded holes in the armature plate
spanner. Plate has wobble notch.
Spline Shaft Armature Plate
• Splined shaft can be identified by
holes (not threaded) in the armature
plate spanner. Plate has flat cut-out.
(used only on some SD7H15 models)
SANDEN CLUTCH COILS
DESCRIPTION
PART#
SD5H14 replacement 24V coil, 1 wire ................... 5611
SD7 replacement 2 wire12V coil (no diode) .......... 5612
SD7H15 replacement 24V coil, 1 wire ................... 5614
7H Series, 12V sealed type coil, O.E. CAT ........... 5617
7H Series, 24V sealed type coil, O.E. CAT ........... 5618
5537
SANDEN/SANKYO
Compressor Shaft Key
(10 per box)
204
5612
5614
5611
5545
CLUTCH SNAP RING KIT - 7H15
© 2011 MEI Corporation
SANDEN — CLUTCHES
No. of
Grv’s
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
6
6
6
6
6
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
10
10
10
10
10
10
10
12
12
CLUTCH
O.D.
PART NO.
122 mm 4-3/4"
5148
122 mm 4-3/4"
5061
138 mm 5-7/16" 5135
138 mm 5-7/16" 50400
138 mm 5-7/16" 50417
152 mm 6"
5134
158 mm 6-1/4"
5059
158 mm 6-1/4"
5133
158 mm 6-1/4"
5119
158 mm 6-1/4"
50415
169 mm 6-7/8"
5121
125 mm 4.9"
5163
125 mm 4.9"
5138
125 mm 4.9"
5138S
125 mm 4.9"
5066
125 mm 4.9"
5132
132 mm 5-1/4"
5123
132 mm 5-1/4"
5139
132 mm 5-1/4"
5167
132 mm 5-1/4"
5116
132 mm 5-1/4"
5057
132 mm 5-1/4"
5064
132 mm 5-1/4"
5058
132 mm 5-1/4"
5058A
152 mm 6"
5057D
119 mm 4.6"
5065
119 mm 4.6"
50416
125 mm 4.9"
5164
125 mm 4.9"
5164S
125 mm 4.9"
5168
119 mm 4.6"
5067
119 mm 4.6"
5060
119 mm 4.6"
5149
119 mm 4.6"
50418
130 mm 5.1"
50419
119 mm 4.6"
5174
119 mm 4.6"
5137
119 mm 4.6"
5137S
119 mm 4.6"
5176
125 mm 4.9"
5122
125 mm 4.9"
5068
130 mm 5.1"
5165
130 mm 5.1"
5175
130 mm 5.1"
50420
132 mm 5-1/4"
5169
132 mm 5-1/4"
5179
132 mm 5-1/4"
5120
135 mm 5.3"
5177
140 mm 5.5"
5178S
125 mm 4.9"
5069
125 mm 4.9"
5180
125 mm 4.9"
50412S
125 mm 4.9"
50413
125 mm 4.9"
5173S
126 mm 4.96"
5173
126 mm 4.96"
50412
126 mm 4.96"
50414
126 mm 4.96"
50414S
TECH
TIP
© 2011 MEI Corporation
MODEL
SD5
SD5
SD5
FLX7 SHD
SD7H15SHD
SD7H15SHD
SD5
SD7
SD7H15SHD
FLX SD7H15
SD7
SD7H15
SD7H15
SUPRHD
SD7
SD7
SD5
SD7
SD7H15
SD7H15
SD5
SD7
SD5
SD7H15
SD7H15SHD
SD7H15
SD7
SD7H15
SUPRHD
SD7H15
709/7H15
SD5
SD7H15
SD7H15
SD7H15
SD7H15
SD7H15
SUPRHD
SD7H15
SD7
SD7H15
SD7H15
SD7H15
SD7H15
SD7H15
SD7H15SHD
SD7H15SHD
SD7H15
SUPRHD
SD5
FLX7
FLX7
-
BELT GROOVE WIDTH
1st grv.
2nd grv.
1/2" OH (overhang)
1/2" OH (overhang)
1var. grv
—
1/2"
—
1/2"
—
1/2"
—
1var. grv
—
1var. grv
—
1var. grv
—
1var. grv
—
1/2"
—
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
6 Grooves
—
6 Grooves
—
6 Grooves
—
6 Grooves
—
6 Grooves
—
7 Grooves
—
7 Grooves
—
7 Grooves
—
7 Grooves
—
7 Grooves
—
8 Grooves
—
8 Grooves
—
8 Grooves
—
8 Grooves
—
8 Grooves
—
8 Grooves
—
8 Grooves
—
8 Grooves
—
8 Grooves
—
8 Grooves
—
8 Grooves
—
8 Grooves
—
8 Grooves
—
8 Grooves
—
10 Grooves
—
10 Grooves
—
10 Grooves
—
10 Grooves
—
10 Grooves
—
10 Grooves
—
10 Grooves
—
12 Grooves
—
12 Grooves
—
NOTE
2 wire; Ford TPS Conn., grey,12v, keyed
1 wire, 12 volt, key shaft
24 volt, 1 wire, key shaft
FLX Sealed HD, 12 volt, 4875-9932
2 wire, Sealed HD, 12 volt
24 volt, SD 4640, 8109, 2 wire, key,Dust Cvr
1 wire, 12 volt, key shaft
1 wire, 12 volt, key shaft
24 volt, 1 wire; Cat O.E., key shaft, Dust Cvr
24 volt, 1 wire+ground, key shaft
2 wire, Ford TPS Conn., 12 volt, key shaft
2 wire w/diode, spline shaft, 12 volt
2 wire w/diode, key shaft, 12 volt
2 wire w/diode, key shaft, 12v Therm.Fuse
1 wire, 12 volt, key shaft
24 volt, 1 wire, key shaft
2 wire; Ford TPS Conn., 12 volt, key shaft
2 wire, Ford TPS Conn., 12 volt, key shaft
2 wire, spline shaft, 12 volt
2 wire, key shaft, 12 volt
1 wire, 12 volt, key shaft
1 wire, 12 volt, key shaft
24 volt, 1 wire, key shaft
24 volt w/harness adaptor, 1 wire
2 wire, 12 volt, key shaft
1 wire, 12 volt, key shaft
Sanden #4653, 2 wire, Ford Motorhome
2 wire w/diode, key shaft, 12 volt
2 wire w/diode, key shaft, 12v Therm.Fuse
2 wire w/diode, spline shaft, 12 volt
1 wire w/diode, 12 volt, key shaft
1 wire, 12 volt, key shaft
2 wire, 12 volt, key shaft
12 volt, spline shaft, fits #5700/#5710
12 volt, spline shaft, fits #5701
2 wire, Ford TPS Conn., 12v, spline shaft
2 wire w/diode, key shaft, 12 volt
2 wire w/diode, key shaft, 12v Therm.Fuse
2 wire w/diode, spline shaft, 12 volt
2 wire, Ford TPS Conn., 12 volt, key shaft
1 wire, 12 volt, key shaft
2 wire, key shaft, 12 volt
2 wire w/diode, 12 volt, spline shaft
1 wire, spline shaft, 12 volt
1 wire, spline shaft, 12 volt
2 wire, 12 volt, key shaft, Dust Cvr
24 volt, 2 wire, key shaft, Dust Cvr
2 wire w/diode, key shaft, 12 volt
2 wire w/diode, spline shaft, 12v Therm.Fuse
1 wire, 12 volt, key shaft
1 wire w/jumper, 12 volt, 4872-9930
2 wire MP, 12 volt, Super-HD, 4369-9931
1 wire w/jumper, 24 volt, 4309-6010
2 wire MP, 12 volt, Super-HD, 4369-9931
2 wire MP w/diode, 12v, fits SD4018,SD4407
2 wire MP w/diode, 12 volt
2 wire MP, 12 volt, 4541-9931
2 wire MP, 12 volt, Super-HD, 4370-9931
SANDEN - 2 WIRE METRIPAK CONNECTORS w/DIODE
DO NOT REVERSE:
Black wire = ground Black and White wire = positive
205
CLUTCHES
CLUTCHES USED w/SANDEN COMPRESSORS (SUPPLIED WITH COIL)
CLUTCHES — SANDEN
Listed in ascending order by part number.
5057
OE# 509285
Volt - 12V
Dia. - 5 1/4"/132mm
Grooves - 2
Width - 1/2"
A-B Dist.- 39.55mm
Fits Model
Shaft - keyed
508/510/5H14
5057D
SD7H15SHD
Sealed Heavy Duty
w/dust cover plate
(dust cover not included)
Volt - 12V
Dia. - 152mm
2 Wire
Grooves - 2
Fits Model
Width - 1/2"
SD7H15SHD
Shaft - keyed
5058
OE# 6514-6210
Volt - 24V
Dia. - 5 1/4"/132mm
Grooves - 2
Width - 1/2"
A-B Dist.- 39.55mm
Fits Model
Shaft - keyed
508/510/5H14
5058A
OE# 4435-9931
Volt - 24V
(w/harness adaptor)
Dia. - 132mm
Grooves -2
Shaft - keyed
5059
OE# 6521-6010
Volt - 12V
Dia. - 6 1/4"/158mm
Grooves - 1VG
Width - 7/8"
A-B Dist.- 39.55mm
Fits Model
Shaft - keyed
508/510/5H14
5060
OE# 6520-6010
Volt - 12V
Dia. - 4.6"/119mm
Grooves - Poly 7
Width - .14
A-B Dist.- 46.55mm
Fits Model
Shaft - keyed
508/510/5H14
5061
OE# 61190-4409, 8545-6310
Volt - 12V
Dia. - 4 3/4"/122mm
Grooves - 1
Width - 1/2" OH
A-B Dist.- 43.15mm
Fits Model
Shaft - keyed
508/510/5H14
5064
OE# 6511-6010
Volt - 12V
Dia. - 5 1/4"/132mm
Grooves - 2
Heavy Duty
Width - 1/2"
A-B Dist.- 39.55mm Fits Model
Shaft - keyed
709/7H15
5065
OE# 6524-6010
Volt - 12V
Dia. - 4.6"/119mm
Grooves - Poly 6
Width - .14"
A-B Dist.- 62.55mm
Shaft - keyed
5066
OE# 6511-6110
Volt - 12V
Dia. - 4.9"/125mm
Grooves - 2
Width - 1/2"
A-B Dist.- 39.55mm
Shaft - keyed
5067
OE# 6512-6210
Volt - 12V
Dia. - 4.6"/119mm
Grooves - Poly 7 1 Wire w/diode
Width - .14"
Heavy Duty
A-B Dist.- 46.55mm
Fits Model
Shaft - keyed
709/7H15
5068
OE# 6522-6010
Volt - 12V
Dia. - 4.9”/125mm
Grooves - 8
Width - .14"
A-B Dist.- 46.00mm
Shaft - keyed
CLUTCHES
1 Wire
Fits Model
SD7H15
206
Fits Model
709/7H15
Fits Model
709/7H15
Fits Model
7H15
© 2011 MEI Corporation
SANDEN — CLUTCHES
Listed in ascending order by part number (continued).
5120
OE# 4726-9931
Volt - 24V
Dia. - 5 1/4"/132mm
Grooves - Poly 8
Width - .14"
A-B Dist.- 34.00mm
Shaft - keyed
CAT OE Plug
USED ON COMPRESSOR: Fits Model
SD4726
709/7H15
5121
OE# 6506-6010
Volt - 12V
Dia. - 6 7/8”/169mm
Grooves - 1
Width - 1/2"
A-B Dist.- 38.55mm
Ford OE Plug
Shaft - keyed
USED ON COMPRESSOR: Fits Model
709/7H15
SD4602
5122
Volt - 12V
Dia. - 4.9”/125mm
Grooves - Poly 8
Width - .14"
Shaft - keyed
Ford OE Plug
USED ON COMPRESSOR:
Fits Model
SD7804
709/7H15
5123
Volt - 12V
Dia. - 5 1/4"/132mm
Grooves - 2
Width - 1/2"
Shaft - keyed
Ford OE Plug
USED ON COMPRESSOR : Fits Model
SD5730
508/510/5H14
5132
SD7H15
Volt - 24V
Dia. - 4.9"/125mm
Grooves - 2
Width - 1/2"
1 Wire w/ground
Shaft - keyed
Fits Model SD7
CLUTCHES
5069
OE# 6518-6010
Volt - 12V
Dia. - 4.9"/125mm
Grooves - Poly 10
Width - .14"
Fits Model
A-B Dist.- 50.79mm
508/510/5H14
Shaft - keyed
5119
5116
OE# 4604-6880
OE# 6594-6010
SD7H15SHD
Volt - 12V
Sealed Heavy Duty
Dia. - 5 1/4"/132mm
Volt - 24V
Grooves - 2
Dia. - 6 1/4”/158mm
CAT OE Plug
Width - 1/2"
2 Wire Metripak Grooves - 1VG
Fits Model
A-B Dist.- 39.55mm
Fits Model Width - 1/2"
709/7H15
Shaft - keyed
709/7H15 Shaft - keyed
5133
SD7HD
Volt - 12V
Dia. - 6 1/4”/158mm
Grooves - 1 vg.
Shaft - keyed
© 2011 MEI Corporation
5134
OE# 4640-9931
Sealed Heavy Duty
Volt - 24V
Dia. - 6”/152mm
Grooves - 1
Width - 1/2"
Shaft - keyed
1 Wire
709/7H15
5135
SD5
Volt - 24V
Dia. - 5 7/16"/138mm
2 Wire Grooves - 1 vg.
USED ON COMPRESSOR:
1 Wire
SD7H15SHD Shaft - keyed
SD4640, SD8109
Fits Model SD5
5137
OE# 4734-6880;
4424-9931
Volt - 12V
Dia. - 4.6"/119mm
Grooves - Poly 8
Width - .14"
Shaft - keyed
2 Wire
Metripak
Fits Model
709/7H15
207
CLUTCHES — SANDEN
Listed in ascending order by part number (continued).
5138
OE# 6593-6010
Volt - 12V
Dia. - 4.9”/125mm
Grooves - 2
2 Wire Metripak
Width - 1/2"
Fits Model
A-B Dist.- 39.55mm
709/7H15
Shaft - keyed
5148
Volt - 12V
Dia. - 4 3/4"/122mm
Grooves - 1
Width - 1/2" OH
Shaft - keyed
Ford OE Plug
USED ON COMPRESSOR:
Fits Model
SD9594
508/510/5H14
5149
OE# 4618-9931
Kodiak / Topkick
Volt - 12V
Dia. - 4.6"/119mm
Grooves - 7
Shaft - keyed
2 Wire
Metripak
Fits Model
SD7H15
5163
OE# 4740-9931
Volt - 12V
Dia. - 4.9”/125mm
Grooves -2
Width - 1/2"
Shaft - splined
5164S
Super Heavy Duty
SUPRHD type clutch
Volt - 12V (w/therm. fuse)
Dia. - 4.9”/125mm
Grooves - 6
Width - .14”
2 Wire
Shaft - keyed
Metripak
5165
OE# 4700-9931
Volt - 12V
Dia. - 5.1”/130mm
Grooves - 8
Width - .14”
Shaft - keyed
2 Wire
Fits Model
SD7H15
5167
OE# 4777-9931
Volt - 12V
Dia. - 5 1/4"/132mm
Grooves - 2
2 Wire/Spline
Width - 1/2"
Fits Model
Shaft - splined
7H15
5139
OE# 6504-6010
Volt - 12V
Dia. - 5 1/4"/132mm
Grooves - 2
Width - 1/2"
A-B Dist.- 39.55mm
Ford OE Plug
Shaft - keyed
USED ON COMPRESSOR: Fits Model
709/7H15
SD4603
5164
OE# 4424-9931,
4756-9931, 4793-9931
Volt - 12V
Dia. - 4.9”/125mm
Grooves - 6
2 Wire
Width - .14”
Fits Model
Shaft - keyed
7H15
CLUTCHES
5137S
Super Heavy Duty
SUPRHD type clutch
Volt - 12V (w/therm. fuse)
Dia. - 4.6"/119mm
Grooves - Poly 8
Width - .14"
2 Wire
Shaft - keyed
Metripak
5138S
Super Heavy Duty
SUPRHD type clutch
Volt - 12V (w/therm. fuse)
Dia. - 4.9”/125mm
Grooves - 2
Width - 1/2"
2 Wire
A-B Dist.- 39.55mm
Metripak
Shaft - keyed
208
2 Wire
Fits Model
7H15
5168
OE# 4756-9931
Volt - 12V
Dia. - 4.9”/125mm
Grooves - 6
Width - .14”
Shaft - splined
2 Wire
Fits Model
SD7H15
© 2011 MEI Corporation
SANDEN — CLUTCHES
Listed in ascending order by part number (continued).
5169
OE# 4781-9931
Volt - 12V
Dia. - 5 1/4"/132mm
Grooves - 8
Width - .14”
Shaft - splined
5175
OE# 4733-9931
Volt - 12V
Dia. - 5.1”/130mm
Grooves - 8
Shaft - splined
5176
OE# 4776-9931
Volt - 12V
2 Wire Dia. - 4.6"/119mm
Fits Model Grooves - 8
SD7H15 Shaft - splined
2 Wire
Fits Model
SD7H15
CLUTCHES
1 Wire
Fits Model
SD7H15
5174
OE# 4767-9931
Volt - 12V
Dia. - 4.6"/119mm
Grooves - 8
Shaft - splined
Ford OE Plug
USED ON COMPRESSOR: Fits Model
5322
SD7H15
5178S
OE# 4802-9931
Super Heavy Duty
SUPRHD type clutch
Volt - 12V (w/therm. fuse)
2 Wire Dia. - 5 1/2"/140mm
2 Wire
Fits Model Grooves - 8
Metripak
SD7H15 Shaft - splined
5177
OE# 4885-9931
Volt - 12V
Dia. - 5.3”/135mm
Grooves - 8
Shaft - keyed
50401
OE# 4877-9932
Volt - 24V
Dia. - 138mm
Grooves - 1
Width - 1/2"
Shaft - keyed
50402
OE# 4896-9931
Volt - 12V
Dia. - 125mm
Grooves - 2
Width - 1/2"
Shaft - keyed
Fits Model
FLX SD7H15
USED ON COMPRESSOR :
USED ON COMPRESSOR:
5293
5380
© 2011 MEI Corporation
2 Wire
Metripak
7H15HD
5179
SD7H15SHD
Sealed Heavy Duty
Volt - 12V
2 Wire
Dia. - 5 1/4"/132mm
Fits Model
Grooves - 8
SD7H15SHD
Shaft - keyed
50403
OE# 4704-9931
Volt - 12V
Dia. - 132mm
Grooves - 2
Width - 1/2"
Shaft - keyed
USED ON COMPRESSOR:
5320
Ford Plug
2 Wire
SD7H15
50400
OE# 4875-9932
Sealed_HD Clutch
Volt - 12V
Dia. - 138mm
Grooves - 1
Width - 1/2"
Shaft - keyed
Fits Model
FLX SD7H15
USED ON COMPRESSOR:
5292
50410
OE# 4768-9933
Volt - 12V
Dia. - 152mm
Grooves - 8
Shaft - keyed
USED ON COMPRESSOR :
5303
1 Wire
Fits Model
7H15HD
209
CLUTCHES — SANDEN
Listed in ascending order by part number (continued).
50412
OE#
Volt - 12
Dia. - 126mm
Grooves - 10
Shaft - keyed
50411
OE# 4872-9930
Volt - 12V
Dia. - 125mm
Grooves - 10
Shaft - keyed
USED ON COMPRESSOR:
USED ON COMPRESSOR:
SD4018; SD4407
2 Wire
Metripak
w/diode
50413
OE# 4309-6010
Volt - 24V
Dia. - 125mm
Grooves - 10
Shaft - keyed
USED ON COMPRESSOR:
SD4369; SD4384;
SD4412; SD4804
2 Wire
Metripak
USED ON COMPRESSOR:
SD4309
1 Wire
w/jumper
CLUTCHES
5289
1 Wire
w/jumper
50412S
OE# 4369-9931
Super_HD Clutch
Volt - 12V
Dia. - 125mm
Grooves - 10
Shaft - keyed
50414S
OE# 4370-9931
Super_HD Clutch
Volt - 12V
Dia. - 126mm
Grooves - 12
Shaft - keyed
50414
OE# 4541-9931
Volt - 12V
Dia. - 126mm
Grooves - 12
Shaft - keyed
USED ON COMPRESSOR:
SD4541; SD4675
USED ON COMPRESSOR:
2 Wire
Metripak
50417
SD7H15SHD
Sealed Heavy Duty
w/dust cover plate
(dust cover not included)
Volt - 12V
Dia. - 138mm
2 Wire
Grooves - 1
Fits Model
SD7H15SHD
Width - 1/2”
210
5402
SD4088; SD4378
50418
OE# 4796-9930
Volt - 12V
Dia. -119mm
Grooves - 7
Shaft - splined
USED ON COMPRESSOR:
5700, 5710
2 Wire
Metripak
2 Wire
Fits Model
SD7H15
50415
OE# 4870-9930
Volt - 24V
Dia. - 158mm
1 Wire w/ground
Grooves - 1 vg.
Fits Model
Shaft - keyed
FLX SD7H15
50419
OE# 4754-9930
Volt - 12V
Dia. - 130mm
Grooves - 7
Shaft - splined
USED ON COMPRESSOR:
5701
50416
Comp# SD4653
Volt - 12V
1 Wire
Dia. - 119mm
Fits Model SD7
Grooves - 6
50420
OE# 4781-9931
Volt - 12V
2 Wire Dia. - 130mm
1 Wire w/ground
Fits Model Grooves - 8
Fits Model
SD7H15 Shaft - splined
SD7H15
© 2011 MEI Corporation
SELTEC / VALEO — CLUTCHES
Gauge Line
A-B Distance
HOW TO MEASURE CLUTCH: SELTEC / VALEO
IF PART NUMBER ON CLUTCH BEING REPLACED CANNOT
BE READ, USE THE FOLLOWING PROCEDURE TO DETERMINE
REQUIRED CLUTCH PART NUMBER.
Diameter
1. DETERMINE IF 12 OR 24 VOLT.
2. DETERMINE IF CLUTCH IS SINGLE, DOUBLE OR MULTI-GROOVE.
3. MEASURE OUTSIDE DIAMETER OF PULLEY.
3 EYE CLUTCH
3-EYE CLUTCH
(NEW STYLE)
SELTEC introduced a new clutch design which is called "3 Eye." It is designed
for both clockwise or counter clockwise rotation. Due to the isolated mount
design, it provides softer engagement and smoother operation and has the
capability to absorb vibration. Service is easier on the 3 Eye clutch due to a new
designed armature plate that can be easily removed.
All SELTEC / VALEO compressors will be able to use this newer style clutch.
It is dimensionally compatible with the current style so there is no change in
overall compressor length or gauge line. This is a running change, therefore
there will be no compressor part number change with the 3 Eye clutch.
NOTE: TM31 clutches are 5 Eye.
SPRING LEAF CLUTCH
(OLD STYLE)
SELTEC CLUTCH COILS
DESCRIPTION
PART#
COIL - TM15/16 (exc. OH), 1 wire, 12v ................. 5615
COIL - TM15/16 (exc. OH), 1 wire, 24v ................. 5616
COIL - TM31, 2 wire, 12v ....................................... 5619-12
COIL - TM31, 1 wire, 24v ....................................... 5619-24
1 wire
2 wire
CLUTCHES - used with SELTEC / VALEO compressors (supplied with coil)
(Listed in ascending order by groove/diameter. Note: All clutches have spline shaft.)
No. of
Grv’s
1
1
1
2
2
2
2
2
2
2
2
2
2
6
8
8
8
8
8
10
10
10
12
12
CLUTCH
O.D.
125 mm 4.9"
158 mm 6-1/4"
159 mm 6-1/4"
125 mm 4.9"
125 mm 4.9"
132 mm 5-1/4"
132 mm 5-1/4"
132 mm 5-1/4"
132 mm 5-1/4"
145mm 5.7”
145mm 5.7”
152 mm 6"
152 mm 6"
119 mm 4.6"
119 mm 4.6"
119 mm 4.6"
141mm 5.5”
141mm 5.5”
152 mm 6"
127 mm 5"
-
© 2011 MEI Corporation
PART NO.
5056
5199
5054
5050
50203
5055
5077
5076
5198
5104
5105
5078
5035
5053
5051
5106B
5106
50204
5079
5107
5108
50200
5109
50201
CLUTCH
STYLE
3 eye
3 eye
3 eye
Leaf Spring
Leaf Spring
Leaf Spring
3 eye
3 eye
3 eye
5 eye
5 eye
3 eye
3 eye
5 eye
-
GROOVE
1 OH
1 var. grv
1 var. grv
2
2
2
2
2
2
2
2
2
2
6
8
8
8
8
8
10
10
10
12
12
A-Grv (1/2")
B-Grv (5/8")
Serpentine belt
Serpentine belt
49mm gauge line
51mm gauge line
51mm gauge line
Serpentine belt
Serpentine belt
Serpentine belt
Serpentine belt
Serpentine belt
Serpentine belt
NOTE
12Volt, 1 grv Overhang,TM15/16 comp.
24 Volt, TM15/16, 1 wire
12 Volt, TM15/16 comp.
12 Volt, TM15/16, 1 wire
12 Volt, TM15/16, 2 wire
12 Volt, TM 15/16, 1 wire
24 Volt, TM15/16 comp.
12 Volt, TM15/16 comp.
12 Volt, TM15/16 comp. w/diode
12 Volt, TM21 comp 2 wire bullet
24 Volt, TM21 comp 2 wire bullet
12 Volt, TM31HD, 1 wire
12 Volt, TM31HD, 1 wire
12 Volt, TM15/16, 1 wire
12 Volt, TM15/16 comp.
12 Volt, TM21 comp, 2 wire
12 Volt, TM21 comp 2 wire bullet
24 Volt, TM21 comp 2 wire bullet
12 Volt, TM31HD, 1 wire
12 Volt, TM21 comp, 2 wire
12 Volt, TM31 comp
24 Volt, TM31 comp
12 Volt, TM31 comp
24 Volt, TM31 comp
211
CLUTCHES
Groove Width
4. MEASURE
OF PULLEY
GROOVE.divide mm by 25.4
To
convert WIDTH
millimeters
to inches:
5.To
MEASURE
ACCURATELY
THE
A-B
DISTANCE.
convert inches to mm: multiply
inches by 25.4
CLUTCHES — SELTEC / VALEO
Listed in ascending order by part number.
5050
TM 15/16
Volt - 12V
Dia. - 125mm, 4.9”
Grooves - 2
Shaft - splined
Width - 1/2"
A-B Dist.- 39.60mm
5051
TM 15/16
Volt - 12V
Dia. - 119mm, 4.6”
Grooves - Poly 8
Shaft - splined
Width - .14
A-B Dist.- 34.09mm
5053
TM 15/16
Volt - 12V
Dia. - 119mm, 4.6”
Grooves - Poly 6
Shaft - splined
Width - .14
A-B Dist.- 34.09mm
5054
TM 15/16
Volt - 12V
Dia. - 159mm, 6-1/4”
Grooves - 1
Shaft - splined
Width - Variable
A-B Dist.- 39.60mm
5055
TM 15/16
Volt - 12V
Dia. - 132mm, 5-1/4”
Grooves - 2
Shaft - splined
Width - 1/2"
A-B Dist.- 39.60mm
5056
TM 15/16
Volt - 12V
Dia. - 125mm, 4.9”
Grooves - 1 OH
Shaft - splined
Width - 1/2"
A-B Dist.- 61.50mm
5076
TM 15/16
Volt - 12V
Dia. - 132mm, 5-14”
Grooves - 2
Shaft - splined
Width - 1/2"
A-B Dist.- 39.60mm
5077
TM 15/16
Volt - 24V
Dia. - 132mm, 5-1/4”
Grooves - 2
Shaft - splined
Width - 1/2"
A-B Dist. - 39.60mm
5078
TM-31 only
Volt - 12V
Dia. - 152mm, 6”
Grooves - 2
Shaft - splined
Width - 1/2"
A-B Dist. - 78mm
5079
TM-31 only
Volt - 12V
Dia. - 152mm, 6”
Grooves - 8
Shaft - splined
Width - .14
A-B Dist. - 66.5mm
5104
TM 21
Volt - 12V
Dia. - 145mm, 5.7”
Grooves - 2
Shaft - splined
CLUTCHES
5035
TM-31 only
Volt - 12V
Dia. - 152mm, 6”
Grooves - 2
Shaft - splined
Width - 5/8”
212
© 2011 MEI Corporation
SELTEC / VALEO — CLUTCHES
5106
TM 21
Volt - 12V
Dia. - 141mm, 5.5”
Grooves - 8
Shaft - splined
A-B Dist.- 51mm
5106B
TM 21
Volt - 12V
Dia. - 119mm, 4.6”
Grooves - 8
Shaft - splined
A-B Dist.- 49mm
5107
TM 21
Volt - 12V
Dia. - 127mm, 5”
Grooves - 10
Shaft - splined
5108
TM 31
Volt - 12V
Dia. Grooves - 10
Shaft - splined
5109
TM 31
Volt - 12V
Dia. Grooves - 12
Shaft - splined
5198
TM 15/16
Volt - 12V
Dia. - 132mm, 5-1/4”
Grooves - 2
Weatherpak
Shaft - splined
w/diode
3 eye type
5199
TM 15/16
Volt - 24V
Dia. - 158mm, 6-1/4”
Grooves - 1 VG
Shaft - splined
3 eye type
50201
TM 31
Volt - 24V
Grooves - 12
Shaft - splined
50203
Volt - 12V
Dia. - 125mm, 4.9”
Grooves - 2
Shaft - splined
Leaf Spring Type
50204
TM 21
Volt - 24V
Dia. - 141mm, 5.5”
Grooves - 8
Shaft - splined
A-B Dist.- 51mm
CLUTCHES
5105
TM 21
Volt - 24V
Dia. - 145mm, 5.7”
Grooves - 2
Shaft - splined
50200
TM 31
Volt - 24V
Grooves - 10
Shaft - splined
© 2011 MEI Corporation
213

Similar documents

compressors — sanden

compressors — sanden 9. Mounting Type: Ear Mount or Direct Mount (crossbolt or tangential) Type 10. Service Valve: Choose the correct service valve using that section of this catalog

More information

low Side - MEI Corporation

low Side - MEI Corporation 2. Locate the Identification Tag on the compressor body - the part number is stamped on the tag. See compressor id

More information

C - Inter Cars SA

C - Inter Cars SA TABLE OF CONTENTS PAGE NO.

More information

A/C COMPRESSOR APPLICATIONS

A/C COMPRESSOR APPLICATIONS CABRIOLET, Optional (To Chassis/VIN 8H-5-014-03)

More information