The Opportunity

The Opportunity
Restock at best price
2
EROWA ITS
Good Opportunity.
Check out this special offer and order today!
nt
ER-036345
QuickChuck 100 P
5%
ou
isc
D
2
Version
Mounting
Application
Note
System size 100, manual, corrosion-resistant.
With four M8 bolts supplied.
Turning, milling, grinding or EDM/WEDM machines, in dividers and fixtures.
Clamping power up to 10000 Nm. max. 3000 rpm.
nt
R
.00
in EcUe: 1‘238 .00
i
r
928
list p
:
now
nt
R
.00
in EcUe: 888 .00
i
r
6
p
6
t
6
lis
:
now
cou
ER-034387
ER-095124
Version
Attachment
Application
Note
ER-009226
Version
Application
Mounting
ER-009222
Version
Application
Mounting
QuickChuck 50
25
%
Dis
Sealin
Sealing
Seal
Se
al ng
ng plate
p
50
50 C
50
pieces
System
size 50, manual, corrosion‑resistant.
4 x M8 from the rear or 4 x M6 stud bolts with nuts.
On EDM/WEDM centers for light milling and grinding
work. Max. revolutions on rotating axes 200min¹
Clamping power up to 4000 N.
Uniblank
12 pieces
cou
15
%
Dis
Set of 12 units, fitted without machining of body.
To mount electrodes and workpieces of various shapes.
As required.
Prisround
12 pieces
5%
nt
Di
u
sco
R
.00
in EcUe: 336 .00
i
r
5
p
8
2
list
:
now
1
Set of 12 units, square 26.5 mm milled, including
2 setscrews for each unit.
To mount electrodes and workpieces with a base surface
up to 25 mm.
Insert and tighten setscrews. If necessary, center
with spacer plate ER-010532.
R
.00
in EcUe: 336 .00
i
r
5
p
8
2
list
:
now
EROWA ITS
ER-010793
Version
Application
Mounting
Uniholder
12 pieces
5%
nt
u
sco
Di
1
Set of 12 units, groove 20 mm faced, including
2 setscrews for each unit.
To mount electrodes and workpieces with shaft sizes of up
to 20 mm.
Insert and tighten setscrews. If necessary, center with
spacer plate ER-010532.
nt
ER-009219
Version
Application
To fit blank
Uniplate
12 pieces
%
15
ou
isc
Set of 12 units, surface 51 x 51 mm faced, including 2 x
M6 bolts for each unit.
To mount electrodes and workpieces with a base surface
of more than 50 mm.
With 2 x M6 bolts into the base surface.
Version
Application
Mounting
ER-010755
Centering plate 50
50 pieces
%
25
R
.00
in EcUe: 336 .00
i
r
5
p
8
t
2
lis
:
now
D
nt
ou
ER-009214
3
c
Dis
R
.00
in EcUe: 336 .00
i
r
5
28
list p
:
now
Corrosion-resistant, including
4 supporting feet each.
Small electrode weights.
Mounted directly on plane surface of blank.
Chucking spigot F/M EDM for flushing
20 pieces
5%
nt
Di
u
sco
R
.00
in EcUe: 725 .00
i
r
543
list p
:
now
2
Version
Application
Fixed type, manual. Bolt with flushing hole.
Set of 20 spigots.
In Electrode Holders.
For EDMing and easy machining.
R
.00
in EcUe: 536 .00
i
r
2
p
0
4
list
:
now
4
EROWA ITS
ER-015465
Version
Application
Chucking spigot F/A EDM M10 x 45
for flushing, 20 pieces
5%
nt
u
sco
Di
2
Fixed type, automatic. Bolt with flushing hole. Set of 20
spigots.
For electrode holder to be changed automatically. For
EDM-ing and and machining with light cutting force.
R
.00
in EcUe: 725 .00
i
r
544
list p
:
now
ER-007986
Version
Application
ER-008566
Square 15 electrode holder
for ITS 50, 1 piece
5%
nt
u
sco
Di
1
ITS system size 50.
EDM/WEDM.
Collet chuck holder 50
0%
nt
Di
u
sco
R
.00
in EcUe: 523 .00
i
r
4
44
list p
:
now
3
Version
Application
System size 50,
incl. wrench.
For round material up to ø 20 mm.
R
.00
in EcUe: 586 .00
i
r
0
p
1
4
list
:
now
5
The choice...
Special discount for a limited time only. Take the advantage now to stock up
on original EROWA ITS 50 electrode holders. Less preparation time - more efficiency.
Special offer valid until 30th September 2015.
EROWA AG / 04.15
EROWA Group Business Network: a member of ORENDA Holding Ltd.
Subject to technical changes. Registered trademark of EROWA AG,
Copyright © EROWA AG, for a number of products of EROWA AG
patents are existing or pending.
… is yours.
Switzerland
EROWA AG
Knutwilerstrasse 3
CH-6233 Büron
Schweiz
Phone 041 935 11 11
Fax 041 935 12 13
[email protected]
www.erowa.com