Section F – Air Atomizing Spray Nozzles

Transcription

Section F – Air Atomizing Spray Nozzles
Overview
Air Atomizing Spray Nozzles
Table of Contents
If your application requires air atomizing nozzles, you’ll find
information on the largest selection in the industry available in
this section. Choose from dozens of nozzle bodies, assemblies and
spray set-ups to get the precise performance you require.
Basic Information
Set-ups. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F3
Air atomizing nozzles require a single air source for the atomizing
air. Some versions, equipped with a cylinder for automatic
operation or clean-out and shut-off needles, may require an
additional air line. Fluid lines are required for all models. The fluid
line can be pressurized or supplied using a siphon- or gravityfed configuration. It is recommended that air and fluid lines are
equipped with the proper filters, regulators and valves.
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F4
Air atomizing nozzles require spray set-ups. Each set-up consists
of an air cap and fluid cap and some may also include O-rings
and retainer caps. You can select from a wide assortment of
capacities, spray patterns and pressure- or siphon-fed set-ups.
Pressure Spray Set-ups, Internal Mix,
High Transfer Efficiency (HTE). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F19
• Product Range:
– 1/8J and 1/4J Series nozzles are available in many
configurations and operate at standard flow rates. Ranges
from: 0.55 to 58.1 gph at 40 psi (2.08 to 220 l/h at 2.8 bar).
1/8JJ Compact Series
1/8J and 1/4J Series
Overview/Nozzle Bodies/Nozzle Assemblies. . . . . . . . . . . . . . . . . . . F5
Pressure Spray Set-ups, Internal Mix. . . . . . . . . . . . . . . . . . . . . . . . . F9
Pressure Spray Set-ups, External Mix. . . . . . . . . . . . . . . . . . . . . . . . F15
Siphon/Gravity-Fed Spray Set-ups, External Mix. . . . . . . . . . . . . . . F23
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F25
Pressure Spray Set-ups, Internal Mix. . . . . . . . . . . . . . . . . . . . . . . . F27
– Variable spray nozzles provide independent control of liquid,
atomizing air and fan air pressure for fine tuning of flow rate,
drop size, spray distribution and coverage.
Pressure Spray Set-ups, External Mix, High Capacity. . . . . . . . . . F31
Pressure Spray Set-ups, Internal Mix, Air Efficient . . . . . . . . . . . . F33
– 1/2J Series nozzles offer the same features and benefits as
1/8J and 1/4J Series but operate at higher capacities. Ranges
from: 22.2 to 222 gph at 40 psi (84 to 840 l/h at 2.8 bar).
Variable Spray Series
– 1J Series nozzles offer the highest flow rates available. Ranges
from: 120 to 906 gph at 40 psi (454 to 3430 l/h at 2.8 bar).
Variable Spray Nozzles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F36
Additional information can be found in Section G, Automatic Spray
Nozzles and in Section K, Special Purpose Spray Nozzles.
1/2J Series
Nozzle Bodies/Nozzle Assemblies. . . . . . . . . . . . . . . . . . . . . . . . . . . F43
1J Series
Special Purpose
Air atomizing caps
AirJet® Fogger Spray Nozzles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F54
DripSafe™ AirJet Fogger Spray Nozzles. . . . . . . . . . . . . . . . . . . . . . F56
Humidification Spray Nozzles and Units. . . . . . . . . . . . . . . . . . . . . . F58
Humidification System Components. . . . . . . . . . . . . . . . . . . . . . . . . F60
Air Atomizing Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F61
Phone 1-800-95-spray, FAX 1-888-95-spray
Visit Our Web Site: www.spray.com, Email: [email protected]
F1
Air Atomizing
Nozzles
Air Atomizing Nozzles
Air Atomizing Spray Nozzles
Optimization Tips
• Reduce installation time by using split-eyelet connectors on both the air
and fluid lines. Split-eyelet connectors only require a hole drilled into the
pipe, eliminating the need for cutting, threading and brazing operations.
• To eliminate the unintentional release of non-atomized liquid, use a check
valve to shut down liquid flow if no air pressure is detected.
• Use air atomizing nozzles with clean-out needles to eliminate clogging and
ensure optimum performance.
• Use strainers and air filters to ensure optimum performance.
• If positive shut-off is required, use Drip Free™ set-ups with JAU nozzles.
• Use a heat jacket with VAU/VMAU variable spray nozzles to keep viscous
liquids warm and transferable.
• When adjusting air pressure with internal mix nozzles, do not exceed
recommended values as it may result in choking liquid flow. Increasing
liquid flow can also choke air flow.
AutoJet Spray Controllers
and Systems
• For optimal control of your air atomizing spray system, the use of an
AutoJet® Spray System helps conserve liquid usage and reduces scrap by
monitoring and automatically adjusting spray pattern, flow rate, drop size,
liquid pressure and atomizing air pressure.
Air atomizing nozzles
with clean-out needles
Heat jackets
Spray nozzles
Hot fluid
flow channel
Cut out view of heat jacket
showing unique flow channel
F2
Set-ups, Basic Information
• Liquid can be supplied to the nozzle under pressure or it can be supplied through a liquid siphon or gravity-feed.
Pressure Spray Set-ups
Siphon/Gravity-Fed Spray Set-ups
• Liquid is supplied to the nozzle under pressure.
• Liquid is supplied via liquid siphon or is gravity-fed.
• Air and liquid can be externally or internally mixed to produce a
completely atomized spray.
• Designed to draw liquid through the feed line into the air flow
where it is atomized.
Air pressure
regulator
with gauge
– 1/8J and 1/4J Series
Pages F23 – F24
– Compact 1/8JJ Series
Pages F34 – F35
– 1/2J Series
Page 49
– 1J Series
Page 53
Air Atomizing
Nozzles
– 1/8J and 1/4J Series
Pages F5 – F18
– 1/2J Series
Pages F43 – F48
– 1J Series
Pages F50 – F52
– Compact 1/8JJ Series
Pages F25 – F33
– Variable 1/8VAA Series
Pages F36 – F42
• New High Transfer Efficiency (HTE) external mix air atomizing
set-ups recently introduced for 1/4J Series.
– Pages F19 – F22
Air shut-off valve
Air shut-off valve
Air
inlet
Air pressure regulator
with gauge
Air filter
1/4JN
air
atomizing
nozzle
Air filter
1/4JN
air atomizing
nozzle
Liquid
inlet
Siphon
tube
Liquid
shut-off valve
Liquid pressure regulator
with gauge
Air
inlet
Siphon
height
Liquid
container
TW
liquid strainer
F3
Features, Basic Information
Spray Set-up Features
Atomization Control Features
• Each series is available with a pressure spray set-up or siphon
spray set-up.
• Achieved by adjusting the air and liquid pressure in the spray
set-up.
• Each set-up provides a specific spray pattern with a specific
capacity and spray coverage range performance.
• Obtaining finer atomization is accomplished by increasing the
air pressure and/or lowering the liquid pressure, resulting in a
high ratio of air flow rate to liquid flow rate.
• Spray set-ups are interchangeable for each nozzle series.
– Round spray: Extended full cone round spray pattern.
– Wide angle round spray: Hollow cone-type, wide angle round
spray pattern.
– 360° circular spray: Hollow cone-type 360° circular spray pattern.
– Flat spray: Extended flat or sheet-type spray pattern.
– Deflected flat spray: Extended flat or sheet-type spray diverted
away from the axis of the inlet connection.
• Each spray set-up consists of an air cap and fluid cap.
• For more information request Data Sheets 10616 and 10616-1.
External mix with pressure set-ups: Flat and round spray patterns.
Air cap
Fluid cap
Internal Mix Features
External Mix Features
• Liquid and air are mixed internally to produce a completely
atomized spray.
• Liquid and air streams are mixed outside of the nozzle.
• Liquid and gas streams are not independent and a change in air
flow will affect the liquid flow.
• Effective for higher viscosity liquids and abrasive suspensions.
• Air and liquid flow can be controlled independently.
• External mix can use siphon set-ups or pressure set-ups.
• Internal mix uses pressure set-ups and is available with the
following spray patterns:
– 360° circular spray.
– Flat spray.
– Deflected flat spray.
– Round spray.
– Elliptical spray.
– Wide angle round spray.
Internal mix with
pressure set-ups:
Round spray patterns
• When a siphon set-up is used, a round spray pattern is produced.
• When a pressure set-up is used, a flat spray pattern is produced.
External mix with
siphon set-ups:
Round spray patterns
Internal mix with
pressure set-ups:
Flat spray patterns
External mix with
pressure set-ups:
Flat spray patterns
F4
Overview/Nozzle Bodies/Nozzle Assemblies,
1/8J and 1/4J Series air atomizing
Spray set-up for HTE
1/8J, 1/4J
Plug CP1159
2
3
Spray set-up
1/8JN, 1/4JN
1
1/8JCO, 1/4JCO
11005–1/8J, 11005–1/4J
1/4JAU – Drip Free
Shut-off
needle assembly 12810
4
2
3
1. Retainer ring CP1158
2. Air cap
3. Fluid cap
4. Fluid cap gasket CP3612
5. Nozzle body CP1151
6. Back seal gasket CP10439
6
5
Clean-out
Shut-off/clean-out
Air Atomizing
Nozzles
1
Spray set-up for Drip Free™
1
2
3
4
Shut-off/clean-out
needle assembly
Features and Benefits
• The basic J Series nozzle assembly consists of a body and a
spray set-up.
• JN features a manual shut-off needle that enables the flow of
liquid to the nozzle to be stopped.
• Various assemblies can be added to provide shut-off and
clean-out functions.
• JCO features a clean-out needle that is activated manually.
– The needle slides through the liquid orifice to clear
obstructions.
• 1/8J and 1/4J bodies have liquid and air feeds at opposite ends
of the body.
– Bodies are provided with a removable plug so other needle
assemblies may be added in the future.
– Ideal for intermittent spraying applications when liquid can
dry in the orifice between uses.
• 11005 combines the features of JN and JCO offering a
combination shut-off/clean-out needle.
F5
Nozzle Bodies/Nozzle Assemblies,
1/8J, 1/4J
1/8JN, 1/4JN
1/8" and 1/4" NPT or BSPT
1/8JCO, 1/4JCO
11005-1/8J, 1/4J
1/8" or 1/4" NPT or BSPT with
clean-out needle
1/8" or 1/4" NPT or BSPT with
shut-off/clean-out needle
1/8" and 1/4" NPT or BSPT with
shut-off needle
Optimization Tips
See Also
• See page F2 for optimization tips.
• Accessories
– Air line filters
Materials
Material
Nozzle Type
Material
Code
J JN JCO 11005
– Air pressure regulators
– Solenoid valves
– Liquid pressure regulators
– Strainers
Complete Nozzle Assembly
Nozzle Body*
Spray Set-up Only
Spray Set-up
Spray Set-up
1/4 JN – SS + SU11DF – SS
(none)
l
l
l
l
303 Stainless Steel
SS
l
l
l
l
Lucite®*
LUC
l
l
l
l
l
l
Inlet
Conn.
Nozzle
Body
Assembly
Type
Material
Code
Spray
Set-up
No.
Material
Code
*Includes retainer and gasket.
Spray Set-ups
Lucite*
– Pressure gauges
Ordering Info
Nozzle Bodies
Electroless Nickelplated Brass
http://
BSPT connections require the addition of a “B” prior to
the nozzle body inlet connection.
LUC
l
Electroless Nickelplated Brass Air
Cap and
303 Stainless Steel
Fluid Cap
SSBR
l
l
l
l
303 Stainless Steel
SS
l
l
l
l
To order fluid cap only, use fluid cap number (shown in
performance data charts) and material code: 2050-SS.
SU11DF – SS
l
l
Spray
Set-up
No.
Material
Code
To order spray set-up
only, use spray set-up
number and material
code: SU11DF-SS.
To order air cap only, use air cap number (shown in
To order spray nozzle without set-up, use inlet
connection, nozzle body and material code: 1/4JN-SS.
*May not be available for all spray set-ups listed.
Other materials available upon request.
F6
• 1/4JF features a built-in liquid strainer.
• The 7545 multiple swivel spray assembly features each spray
set-up mounted on its own swivel body.
– One or two bodies may be used and each can be rotated 360° to
the desired position.
• 1/4JFN features built-in liquid strainer and liquid shut-off needle.
• JBC features the center lines of the air and liquid inlet entering in
the back of the nozzle and parallel to the spray projection axis.
– Swivel bodies are locked in place by a stainless steel lock screw
that runs vertical through the assembly.
• JACN features air and liquid inlet connections entering the nozzle
at 90° to spray projection axis and a shut-off needle.
• 1/8-2JAC dual spray assembly features two opposing spray
set-ups with the air and liquid inlet connections perpendicular
to the spray axis.
• 6552-1/8JAC miniature assembly body is only 1/2" (13 mm) thick
with a 1-5/32" (29 mm) by 1-1/4" (32 mm) rectangular face.
– The tip of the nozzle projects from the face a maximum of
1-3/16" (30 mm) depending upon the spray set-up used.
• 1/4JBCJ features a steam jacket around the nozzle body for
spraying liquids that are too viscous to spray at room temperature.
With Strainer
Top Inlet
1/4JF and 1/4JFN
1/4" NPT or BSPT (F)
air inlet connection
liquid inlet connection
Swivel
Back Connect
1/8JBC and 1/4JBC
1/8" or 1/4" NPT or BSPT (F)
inlet connection
1/8JAC, 1/8JACN
1/4JAC, 1/4JACN
1/8" or 1/4" NPT or BSPT (F)
inlet connection
Top Inlet
1/8-2JAC
inlet connection
Optimization Tips
Miniature
See Also
• Accessories
7545
1/8" NPT or BSPT (F) air and
6552-1/8JAC
http://
– Pressure gauges
– Solenoid valves
– Strainers
• For JBC, request Data Sheets 4921, 6885 and 6185
• For JAC and JACN, request Data Sheets 4922 and 4922-1
Steam Jacket
• For 1/8-2JAC dual spray assembly, request Data Sheet 6497
• For 7545 multiple swivel spray assembly, request
Data Sheet 7545
• For 6552-1/8JAC, request Data Sheet 6552
• For 1/4JBCJ, request Data Sheets 4610 and 6331
1/4JBCJ
inlet/outlet connection
F7
Air Atomizing
Nozzles
• JAC features air and liquid inlet connections entering the nozzle at
90° to spray projection axis.
• 8650 multiple spray assembly (cluster type) features five spray
set-ups located on the faces of the assembly or four set-ups
located on the side faces.
• 1/4JDLN and 1/4JDLCO feature a screw mount with 9/32" (7 mm)
diameter mounting holes.
– Standard 1/4" (6 mm) screws hold the body to the wall with a
gasket providing the seal.
• 2J is a dual spray assembly with opposing spray set-ups
perpendicular to opposing air and liquid inlets.
– The 1/4JDLN features a shut-off needle and the 1/4JDLCO
features a clean-out needle.
• 20470 Series hand-held air atomizing spray guns feature
lightweight aluminum construction and a comfortable,
easy-to-operate design.
• Thin wall adapters add an adapter locknut and gasket to CP3376
thick wall adapters to provide secure mounting in thin walls and
include CP6378 locknut and CP2804-3 gasket.
• Thick wall adapters replace retainer rings on nozzle assemblies
and fit into threaded wall openings, holding the nozzle securely
in place.
Cluster Type
8650
– Extensions are available in up to 36" (91 cm) lengths.
Twin Spray
Thin Walls
2J
inlet connection
Available for 1/8J and 1/4J
assemblies
Thick Walls
1/8J and 1/4J with 3/4" NPT or
BSPT (M) adapter connection
Optimization Tips
Screw Mount
See Also
• Accessories
20470
http://
– Pressure gauges
– Solenoid valves
– Strainers
• For 8650 multiple spray assembly, request Data Sheet 8650
• For 2J, request Data Sheets 5356 and 6530
• For thin wall adapters , request Data Sheet 3378
• For thick wall adapters, request Data Sheets 3378, 7003
and 7323
Hand-held spray gun
1/4" NPT or BSPT (F) inlet connection
• For 1/4JDLN and 1/4JDLCO, request Data Sheet 7690
• For 20470 Series hand-held air atomizing spray guns,
request Data Sheets 20470J, 20470JN, 20470JMCO,
20470JN-1, 20470JJ, 20470JJN and 20470JJNTK
F8
Air Caps
• For round spray pattern, angle “A” is maintained throughout distance “B”. Beyond “B”, the spray
becomes turbulent and will project out to distance “D”.
• When using a pressure-fed liquid system, the liquid is supplied to the nozzle under pressure.
• The liquid and compressed air or gas are mixed internally to produce a completely atomized spray.
Round spray air caps
produce a narrow, full cone
round spray pattern
Fluid cap
Air cap
Round spray
pattern
A
B
D
1158 retainer ring
3612
gasket
Air Atomizing
Nozzles
1158 retainer ring and 3612 gasket must be ordered separately from the spray set-up, but are included in
the standard nozzle assembly. Please contact your sales engineer.
Performance Data
Round Spray
Spray
Set-up
Spray
Consists of
Set-up
Fluid and
No.
Air Cap
Combination
SU11
Fluid Cap
2050
+
Air Cap
67147
*At the stated pressure in psi.
Liquid Capacity (gallons per hour)* and Air Capacity (standard cubic feet per minute)*
Spray
Dimensions
Liquid Pressure
10
20
30
40
60
Liquid*
Spray
Angle
A (°)
B
(in.)
D
(ft.)
12
10
13
12
9
24
20
13
13
10
14
11
Air*
Air
Air
Air
Air
Air
gph scfm
gph scfm
gph scfm
gph scfm
gph scfm
Press.
Press.
Press.
Press.
Press.
10.0
.66
.55
14.0
1.50
.40
24
1.68
.56
32
1.86
.68
50
2.28
.98
12.0
.48
.67
18.0
1.23
.50
28
1.44
.63
36
1.62
.80
54
2.05 1.07
14.0
.36
.78
22
.99
.63
32
1.08
.82
40
1.32
.93
58
1.80 1.19
–
–
–
24
.86
.70
36
.84
.96
44
1.08 1.07
62
1.56 1.36
36
30
13
–
–
–
26
.72
.76
38
.72
1.03
48
.85
1.23
66
1.32 1.52
44
40
14
15-1/2 12-1/2
–
–
–
28
.60
.82
40
.66
1.11
50
.72
1.33
68
1.23 1.58
–
–
–
30
.45
.93
42
.54
1.19
52
.66
1.38
70
1.11 1.66
62
60
15
17-1/2 14-1/2
Add DF to part number for “Drip Free™” set-ups. Example: SU11DF.
F9
Performance Data
Round Spray
Spray
Set-up
Spray
Consists of
Set-up
Fluid and
No.
Air Cap
Combination
SU12A
SU12
SU22B
SU22
SU42
Fluid Cap
2050
+
Air Cap
73160
Fluid Cap
2850
+
Air Cap
73160
Fluid Cap
40100
+
Air Cap
1401110
Fluid Cap
60100
+
Air Cap
1401110
Fluid Cap
100150
+
Air Cap
1891125
Spray
Dimensions
Liquid Pressure
10
20
30
40
60
Air* Liquid*
Air
Air
Air
Air
Air
gph scfm
gph scfm
gph scfm
gph scfm
gph scfm
Press.
Press.
Press.
Press.
Press.
10.0
.66
.66
18.0
1.44
.87
24
1.98 1.00
30
2.40 1.14
40
3.30 1.36
12.0
.54
.77
20
1.32
.98
28
1.68 1.17
34
2.16 1.29
46
2.94 1.54
14.0
.42
.90
22
1.20 1.06
32
1.44 1.35
38
1.92 1.47
52
2.58 1.83
–
–
–
24
1.08 1.16
34
1.32 1.46
42
1.62 1.68
58
–
–
–
26
.90
1.26
36
1.20 1.57
44
1.50 1.78
–
–
–
–
–
–
38
1.11 1.66
46
1.38 1.88
–
–
–
–
–
–
40
1.02 1.76
48
12.0
1.26
.73
22
2.16 1.05
30
2.90 1.24
16.0
1.08
.94
26
1.74 1.26
34
2.46 1.42
20
.90
1.15
30
1.44 1.47
38
22
.81
1.25
34
1.26 1.67
24
.78
1.36
38
26
.77
1.43
40
28
.76
1.56
16.0
Spray
Angle
A (°)
B
(in.)
D
(ft.)
12
10
12
17
12
20
20
13
18
13
2.28 2.09
34
30
13
19
14
62
2.10 2.26
42
40
13
20
15
66
1.86 2.46
1.32 1.98
70
1.68 2.67
58
60
15
22
17
36
4.32 1.26
48
5.82 1.50
40
3.85 1.36
52
5.28 1.65
22
10
12
19
13
2.10 1.65
44
3.55 1.56
56
4.92 1.73
34
20
13
20
14
42
1.74 1.87
48
2.80 1.78
60
4.56 1.88
42
30
13
21
15
1.08 1.87
46
1.50 2.03
52
2.46 2.01
64
4.08 2.08
1.02 1.96
50
1.24 2.25
56
2.16 2.20
68
3.72 2.25
48
40
14
22
16
42
.94
2.04
52
1.20 2.36
60
1.86 2.36
70
3.60 2.34
60
60
15
3.44 2.68
28
5.03 3.71
40
6.10 4.72
48
7.75 5.30
65
10.7 6.74
20
2.35 3.20
32
3.70 4.17
44
5.03 5.17
55
5.95 6.07
75
8.67 7.73
24
10
18
26
16
22
1.90 3.46
36
2.64 4.65
48
3.95 5.65
65
3.55 7.28
80
7.65 8.25
40
20
20
30
20
24
1.54 3.70
40
1.85 5.13
55
2.30 6.50
75
1.95 8.50
85
6.65 8.80
55
30
20
32
22
26
1.23 3.97
44
1.30 5.63
60
1.56 7.12
80
1.40 9.10
90
5.64 9.40
28
.96
4.22
48
.90
6.10
65
1.08 7.75
85
1.00 9.70
95
4.63 10.0
75
40
21
36
26
30
.72
4.48
50
.76
6.36
70
.73
8.35
90
.72
10.3
100
3.62 10.6
85
60
21
38
30
12.0
8.1
2.00
20
13.6 2.55
30
16.3 3.25
38
19.5 3.74
54
25.7 4.66
14.0
6.6
2.32
22
12.0 2.85
34
13.1 3.75
42
16.5 4.20
60
21.8 5.34
14
10
17
24
16
16.0
4.9
2.66
24
10.2 3.15
38
9.9
4.32
46
13.6 4.71
65
18.5 5.98
26
20
18
27
19
18.0
3.4
3.00
26
8.6
3.45
40
8.7
4.61
50
10.8 5.30
70
15.2 6.68
40
30
20
30
22
–
–
–
28
7.2
3.75
42
7.6
4.90
52
9.6
5.58
75
12.2 7.80
–
–
–
30
5.9
4.05
44
6.6
5.20
54
8.6
5.85
80
10.0 8.14
50
40
20
31
23
–
–
–
32
4.6
4.35
46
5.6
5.50
56
7.6
6.14
85
8.0
70
60
21
36
28
14
10
19
35
20
24
20
20
39
23
34
30
21
41
25
44
40
21
42
26
54
60
22
46
30
8.90
14.0
11.7 3.05
20
27.5 3.04
28
36.6 3.55
32
49.4 3.31
42
70.6 3.17
16.0
8.5
3.60
22
23.0 3.49
30
32.6 3.96
36
42.2 4.10
46
65.0 3.85
–
–
–
24
18.0 3.95
32
28.7 4.36
40
35.1 4.90
50
59.0 4.63
–
–
–
26
14.4 4.40
34
24.8 4.78
44
28.0 5.66
54
53.2 5.40
–
–
–
28
11.3 4.85
36
20.9 5.20
46
24.5 6.05
58
47.4 6.16
–
–
–
–
–
–
38
17.5 5.60
48
21.3 6.45
65
37.8 7.54
–
–
–
–
–
–
40
14.6 6.03
50
18.4 6.86
70
30.0 8.55
23-1/2 17-1/2
F10
Air Caps
• For wide angle round spray, dimensions “A”, “B” and “C” are the pattern widths at distances from
the nozzle.
• The total distance of spray projection from the nozzle to the maximum dispersal point is
represented by “D”.
Wide angle round spray and
360° circular spray air caps
produce hollow cone, wide
angle round spray and
360° circular spray patterns.
Fluid cap
Air cap
C
B
A
Wide angle
round spray pattern
6"
(15 cm)
9" (23 cm)
15" (38 cm)
D
1158 retainer ring
3612
gasket
Air Atomizing
Nozzles
Performance Data
Wide Angle Round Spray
Spray
Set-up
Spray
Consists of
Set-up
Fluid and
No.
Air Cap
Combination
SU16
Fluid Cap
2050
+
Air Cap
67-6-20-70°
Fluid Cap
60100
SU26
+
Air Cap
140-6-37-70°
Spray
Dimensions
Liquid Pressure
10
20
30
40
60
Air
Air
Air
Air
Air
A
gph scfm
gph scfm
gph scfm
gph scfm
gph scfm Air* Liquid*
Press.
Press.
Press.
Press.
Press.
(in.)
8.0
1.41
.36
14.0
2.10
.42
22
2.36
.56
30
2.53
.68
44
2.95
.81
10.0
1.14
.43
16.0
1.90
.50
26
2.02
.69
34
2.23
.81
48
2.72
.94
12.0
.79
.50
18.0
1.68
.56
30
1.61
.83
38
1.90
.94
55
2.30 1.20
14.0
.45
.60
20
1.44
.64
34
1.15 1.00
42
1.50
1.1
60
1.92 1.40
–
–
–
22
1.17
.71
36
.91
1.07
46
1.10 1.26
65
1.50 1.60
–
–
–
Fluid Cap
40100
SU26B
+
Air Cap
140-6-37-70°
B
(in.)
C
(in.)
D
(ft.)
7
9
5
10
10
5-1/2
20
20
6
34
30
6-1/2
8
10
42
40
6-1/2
8
10-1/2
9
60
60
7-1/2
9
12
13
12
10
7
7-1/2 9-1/2
6
7
24
.91
.80
38
.68
1.16
48
.90
1.35
70
1.07 1.80
12.0
1.85 1.78
22
3.30 2.30
30
5.10 2.54
38
6.40 2.84
54
8.76 3.44
14.0
.55
2.20
24
2.20 2.67
32
4.25 2.85
42
4.70 3.42
56
8.10 3.74
–
–
–
26
1.20 3.05
34
3.35 3.18
44
3.90 3.72
58
7.44 4.03
24
20
7-1/2
10
13
8
–
–
–
–
–
–
36
2.50 3.50
46
3.06 4.05
60
6.76 4.32
34
30
7-1/2
10
13
10-1/2
–
–
–
–
–
–
38
1.60 3.85
48
2.25 4.42
65
5.10 5.10
–
–
–
–
–
–
40
.70
4.30
50
1.40 4.84
70
3.50 6.00
46
40
8
–
–
–
–
–
–
–
–
–
52
.60
5.34
75
1.85 6.95
60
60
8-1/2
11
10.0
6.3
1.14
20
9.0
1.60
30
11.2 2.04
40
12.4 2.54
56
16.2 2.75
12.0
3.6
1.54
22
6.9
2.00
32
9.3
2.44
42
10.6 2.92
58
14.8 3.11
12
10
7-1/2
10
14.0
2.0
2.00
24
5.1
2.40
34
7.4
2.80
44
8.8
3.33
60
13.8 3.50
22
20
8
10-1/2 14-1/2 10-1/2
–
–
–
26
3.3
2.80
36
5.4
3.20
46
7.1
3.72
65
9.8
4.42
34
30
8
10-1/2 14-1/2 13-1/2
–
–
–
–
–
–
38
3.6
3.60
48
5.4
4.14
70
6.5
5.36
–
–
–
–
–
–
40
2.3
3.98
50
3.6
4.51
75
4.0
6.31
46
40
8
11
–
–
–
–
–
–
–
–
–
52
2.2
4.91
80
2.4
6.51
65
60
8
11
9-1/2 12-1/2
6
10-1/2 13-1/2 13-1/2
14-1/2 19-1/2
14
15
7
16-1/2
15-1/2 22-1/2
F11
Performance Data
Spray
Set-up
Spray
Consists of
Set-up
Fluid and
No.
Air Cap
Combination
Spray
Dimensions
Liquid Pressure
10
20
30
40
60
Air
Air
Air
Air
Air
A
gph scfm
gph scfm
gph scfm
gph scfm
Press.
Press.
Press.
Press.
Press.
(in.)
Fluid Cap
60100
SU29
+
Air Cap
140-6-52-70°
Fluid Cap
40100
SU30
+
Air Cap
120-6-35-60°
Fluid Cap
100150
SU46
+
Air Cap
189-6-62-70°
18.0
9.4
3.0
30
13.4 4.15
44
15.3 5.45
60
15.6 7.05
80
21.4 8.55
22
7.7
3.6
34
11.9 4.65
48
13.8
5.9
70
12.5 8.25
85
19.5 9.15
26
6.0
4.13
38
10.3
5.1
55
11.3 6.75
80
9.3
9.45
90
17.9 9.75
28
5.2
4.4
42
8.9
5.6
65
7.8
8.0
85
7.8 10.05
30
4.4
4.7
46
7.3
6.1
70
6.1
8.6
90
6.2
32
3.7
5.0
50
5.8
6.65
75
4.5
9.25
95
4.8
34
3.0
5.25
60
2.4
7.95
80
3.3
9.85
100
3.7
16.0
3.24 1.43
28
4.60 1.96
42
5.27 2.67
18.0
2.61 1.59
32
3.37 2.27
46
4.0
20
2.08 1.75
36
2.45 2.55
22
1.62 1.90
40
24
1.30 2.06
42
26
1.04 2.20
28
.82
24
26
B
(in.)
C
(in.)
D
(ft.)
10
13
18
28
10
8
42
20
8
95
16.5 10.35 65
30
8-1/2
11
14-1/2
27
10.7
100
9
11-1/2
15
30
–
11.9
–
15.1 10.95 85
–
–
90
–
–
40
11.3
9-1/2 12-1/2
16
34
55
5.69 3.30
80
7.10 4.50
2.96
60
4.24 3.68
85
5.80 4.88
48
3.45 3.11
65
3.15 4.06
90
4.65 5.27
1.75 2.85
50
3.03 3.26
70
2.31 4.44
95
3.75 5.65
1.45 3.00
55
2.11 3.63
75
1.72 4.82
100
3.00 6.03
44
1.21 3.14
60
1.47 3.98
80
1.32 5.20
–
–
–
2.35
46
1.0
3.28
65
1.03 4.36
85
1.05 5.58
–
–
–
6.7
5.5
38
10.7
7.4
48
16.5
8.8
60
18.6 10.4
85
29.2 13.7
5.2
5.9
42
7.6
8.3
52
12.5
9.6
65
13.7 11.4
90
24.6 14.7
28
4.0
6.3
44
6.2
8.7
56
9.2
10.4
70
10.0 12.4
95
20.7 15.8
30
3.0
6.8
46
5.0
9.1
60
6.6
11.3
75
7.4
13.5
100
17.5 16.9
32
2.0
7.2
48
4.0
9.5
62
5.6
11.7
80
5.5
14.5
–
–
–
–
–
–
50
3.0
9.9
65
4.4
12.3
85
4.0
15.5
–
–
–
–
–
–
52
2.4
10.3
70
2.6
13.3
90
2.5
16.6
–
–
–
60
10-1/2 13-1/2
21
22
10
6
7-1/2
9
9
40
20
6-1/2
8
9-1/2
15
50
30
6-1/2
8
9-1/2
18
70
40
7
8-1/2
10
24
90
60
7-1/2 9-1/2
11
31
28
10
9-1/2
18
18
46
20
10
13-1/2 18-1/2
21
60
30
11
14-1/2
20
24
75
40
11-1/2
15
21
26
90
60
13
16-1/2
23
32
13
360° Circular Spray
Spray
Set-up
Spray
Consists of
Set-up
Fluid and
No.
Air Cap
Combination
SU340C
Fluid Cap
60150
+
Air Cap
189-6-62160HC
Liquid Pressure
10
20
30
40
60
Air
Air
Air
Air
Air
gph scfm
gph scfm
gph scfm
gph scfm
gph scfm
Press.
Press.
Press.
Press.
Press.
20
4.0
2.45
34
6.6
4.09
50
7.1
6.38
60
11.0
7.6
85
14.4 11.8
22
2.8
2.7
38
4.4
4.8
52
6.2
6.75
65
8.3
8.63
90
12.0 13.0
24
2.0
2.97
42
2.8
5.5
56
4.4
7.55
70
6.1
9.78
95
9.8
14.1
26
1.5
3.3
46
1.7
6.34
60
3.2
8.41
80
3.1 12.44
100
7.8
15.4
28
1.1
3.62
48
1.3
6.85
70
1.3 11.75
90
1.4
–
–
–
15.4
360° circular spray pattern
F12
Air Caps
• For flat spray pattern, dimensions “A”, “B” and “C” are the pattern widths at distances from the
nozzle.
Flat spray and deflected flat
spray air caps produce flat or
deflected flat spray patterns.
Fluid cap
Air cap
C
B
A
Flat spray
pattern
6"
(15 cm)
9" (23 cm)
15" (38 cm)
3612
gasket
Air Atomizing
Nozzles
1158 retainer ring
D
Performance Data
Flat Spray
Spray
Set-up
Spray
Consists of
Set-up
Fluid and
No.
Air Cap
Combination
SU13A
SU13
SUN13
Fluid Cap
2050
+
Air Cap
73328
Fluid Cap
2850
+
Air Cap
73328
Fluid Cap
2850
+
Air Cap
73335
Spray
Dimensions
Liquid Pressure
10
20
30
40
60
Air
Air
Air
Air
Air
gph scfm
gph scfm
gph scfm
gph scfm
Press.
Press.
Press.
Press.
Press.
10.0
1.44
.84
18.0
2.17 1.12
28
2.49 1.47
38
2.77 1.84
55
3.41 2.43
12.0
1.25
.96
22
1.82 1.31
32
2.19 1.64
42
2.49 2.01
65
2.83 2.85
14.0
1.09 1.08
26
1.50 1.50
36
1.89 1.82
46
2.20 2.19
75
16.0
.93
1.20
30
1.20 1.68
40
1.58 2.00
50
1.93 2.37
18.0
.79
1.32
34
.93
1.87
44
1.30 2.18
60
1.25 2.81
20
.65
1.43
38
.68
2.07
48
1.03 2.36
65
.93
22
.53
1.55
40
.57
2.16
55
.65
2.68
70
.65
12.0
2.17
.70
20
3.35
.96
30
3.98 1.27
14.0
1.80
.82
24
2.71 1.14
34
3.41 1.45
16.0
1.45
.95
28
2.06 1.34
38
18.0
A
(in.)
B
(in.)
C
(in.)
D
(ft.)
16
10
10
14
18
8-1/2
2.26 3.26
30
20
14
19
26
10
85
1.69 3.67
40
30
15
21
30
10-1/2
90
1.40 3.88
3.02
95
1.13 4.09
50
40
18-1/2
24
34
11
3.25
100
.88
4.29
85
60
22
29
37
13
38
4.66 1.49
65
4.8
2.38
42
4.14 1.65
70
4.21 2.62
16
10
14
18
28
7
2.85 1.64
46
3.6
1.85
75
3.63 2.86
30
20
17
24
32
8
1.08 1.07
30
1.76 1.45
42
2.29 1.85
50
3.08 2.05
80
3.05 3.10
42
30
20
26
35
8-1/2
20
.77
1.2
32
1.44 1.56
46
1.72 2.07
60
1.76 2.58
85
2.48 3.35
–
–
–
34
1.18 1.67
48
1.43 2.18
65
1.2
2.84
90
1.98 3.60
50
40
23
30
38
9
–
–
–
36
.94
1.78
50
1.2
2.28
70
.76
3.09
95
1.57 3.85
80
60
23
30
38
10-1/2
14.0
2.4
.89
22
3.2
1.13
34
3.4
1.63
40
4.4
1.77
60
5.0
2.53
16.0
2.1
1.05
26
2.8
1.38
38
2.9
1.86
44
3.8
1.99
65
4.4
2.73
20
10
4
5
7
10
18.0
1.7
1.14
30
2.1
1.62
42
2.3
2.07
48
3.3
2.22
70
3.9
3.00
34
20
5
6
8
12
20
1.4
1.26
34
1.5
1.87
46
1.8
2.36
54
2.6
2.55
75
3.4
3.25
46
30
5
7
9
13
24
.81
1.54
38
1.2
2.1
50
1.4
2.58
60
1.9
2.98
80
3.0
3.57
28
.54
1.76
42
.72
2.38
60
.60
3.16
70
1.1
3.53
90
2.3
4.12
54
40
6
9
11
14
32
.30
1.96
48
.39
2.69
70
.33
3.65
85
.40
4.27
100
2.0
4.65
75
60
8
10
13
16
F13
Performance Data
Flat Spray
Spray
Set-up
Spray
Consists of
Set-up
Fluid and
No.
Air Cap
Combination
SU14
SUN23
Fluid Cap
2850
+
Air Cap
73320
Fluid Cap
60100
+
Air Cap
125340
SU23B
Fluid Cap
40100
+
Air Cap
125328
SU23
Fluid Cap
60100
+
Air Cap
125328
SU43
Fluid Cap
100150
+
Air Cap
189351
Spray
Dimensions
Liquid Pressure
10
20
30
40
60
Air
Air
Air
Air
Air
A
gph scfm
gph scfm
gph scfm
gph scfm
Press.
Press.
Press.
Press.
Press.
(in.)
18.0
20
22
24
26
28
–
14.0
16.0
18.0
20
–
–
–
16.0
18.0
20
22
24
–
12.0
14.0
16.0
18.0
20
22
–
14.0
16.0
–
–
–
–
–
1.04
.80
.62
.47
.35
.25
–
4.5
2.9
2.0
.84
–
–
–
2.95
2.25
1.72
1.32
1.00
–
7.0
5.4
4.2
3.3
2.7
2.0
–
7.7
5.0
–
–
–
–
–
1.05
1.15
1.25
1.35
1.45
1.55
–
.80
.97
1.17
1.42
–
–
–
1.92
2.10
2.30
2.50
2.70
–
1.15
1.35
1.57
1.69
1.97
2.20
–
3.17
3.83
–
–
–
–
–
30
34
36
38
40
42
44
24
26
28
30
32
34
36
28
30
32
34
36
–
22
26
30
32
34
36
38
26
28
–
–
–
–
–
1.56
1.10
.90
.74
.60
.47
.35
7.5
6.0
4.5
3.4
2.4
1.3
.80
4.45
3.87
3.30
2.78
2.28
–
11.5
8.3
6.0
5.1
4.3
3.6
3.0
10.5
7.0
–
–
–
–
–
1.43
1.61
1.70
1.79
1.88
1.97
2.07
1.24
1.44
1.68
1.82
2.06
2.32
2.61
2.66
2.84
3.04
3.22
3.40
–
1.65
2.02
2.40
2.60
2.78
2.97
3.16
4.55
5.15
–
–
–
–
–
42
44
46
48
50
55
–
34
36
38
40
42
46
50
38
40
42
44
46
48
34
38
42
46
48
50
52
34
36
38
40
42
–
–
2.06
1.80
1.57
1.35
1.13
.70
–
9.5
7.8
6.5
5.2
4.1
2.6
1.1
5.94
5.40
4.86
4.32
3.78
3.25
12.4
9.8
7.8
5.9
5.0
4.3
3.7
20.8
16.6
12.8
9.5
6.7
–
–
1.75
1.85
1.94
2.04
2.13
2.36
–
1.74
1.96
2.2
2.53
2.65
3.25
3.72
3.22
3.40
3.55
3.74
3.93
4.12
2.20
2.57
2.95
3.34
3.52
3.71
3.90
4.75
5.25
5.8
6.35
6.85
–
–
55
60
65
70
–
–
–
44
46
48
52
56
60
65
46
50
52
54
56
58
46
50
54
56
60
65
70
42
44
46
48
50
52
54
2.16
1.60
1.15
.76
–
–
–
11.1
9.7
8.4
5.7
3.9
2.4
1.1
7.50
6.45
5.90
5.40
4.87
4.34
13.7
10.9
8.7
7.8
6.4
4.6
3.3
29.4
25.1
20.8
16.7
13.1
10.0
7.3
2.15
2.38
2.62
2.85
–
–
–
2.2
2.46
2.69
3.3
3.84
4.36
5.04
3.66
3.97
4.15
4.32
4.50
4.70
2.75
3.14
3.51
3.70
4.06
4.53
5.00
5.15
5.6
6.05
6.6
7.15
7.75
8.3
75
80
85
90
–
–
–
56
60
65
70
80
90
95
65
70
75
80
85
90
65
75
80
85
90
95
100
58
60
65
70
75
80
–
3.20
2.66
2.19
1.75
–
–
–
19.8
16.7
13.5
9.7
4.8
1.8
.70
9.70
8.60
7.50
6.40
5.30
4.25
18.3
12.6
10.6
8.7
6.9
5.5
4.5
44.7
41.0
31.4
22.5
15.0
8.7
–
2.66
2.90
3.13
3.36
–
–
–
2.56
2.97
3.5
4.33
5.73
7.4
8.38
4.80
5.20
5.60
6.00
6.48
6.96
3.56
4.47
4.95
5.40
5.85
6.30
6.76
6.05
6.42
7.45
8.75
10.1
11.45
–
B
(in.)
C
(in.)
D
(ft.)
22
10
10
13
18
6
38
20
14
20
27
6-1/2
46
30
23
29
36
6-1/2
60
40
24
29
37
7
80
60
25
30
38
7-1/2
16
10
4
5
6
8
30
20
4
5
7
10
40
30
5
7
9
11
52
40
6
8
11
12
70
60
8
10
14
13
20
32
42
54
75
10
20
30
40
60
6
9
10
12
13
7
11
13
15
16
8
13
18
18
19
10
10-1/2
11
11-1/2
13
16
10
7
9
12
11
32
20
9
12
16
11-1/2
46
30
10
13
17
12
56
40
12
15
19
12-1/2
85
60
13
16
20
14-1/2
14
10
7
8
10
11
26
20
10
12
17
12-1/2
38
30
10
12
18
14
48
40
13
16
21
15
70
60
14
17
23
17
Deflected Flat Spray
Spray
Set-up
Spray
Consists of
Set-up
Fluid and
No.
Air Cap
Combination
SU240E
Fluid Cap
28150
+
Air Cap
189110-75°
Liquid Pressure
10
20
30
40
60
Air
Air
Air
Air
Air
gph scfm
gph scfm
gph scfm
gph scfm
gph scfm
Press.
Press.
Press.
Press.
Press.
6.0
8.0
10.0
12.0
–
2.9
2.5
2.0
1.5
–
1.6
1.9
2.3
2.7
–
14.0
16.0
18.0
20
22
3.9
3.5
3.1
2.8
2.3
2.6
2.8
3.1
3.5
3.8
22
24
26
30
34
4.7
4.3
4.0
3.3
2.3
3.3
3.6
3.8
4.5
5.2
26
32
38
44
46
5.8
4.8
3.8
2.8
2.3
3.6
4.4
5.3
6.2
6.6
38
46
54
62
70
7.4
6.4
5.3
4.2
2.8
4.6
5.5
6.6
7.8
9.4
Deflected flat spray pattern
F14
Pressure Spray Set-ups, External Mix,
Air Caps
• Atomization can be controlled by varying the air pressure without changing liquid flow rates with
external mix set-ups.
• For flat spray, dimensions “A”, “B” and “C” are the pattern widths at distances from the nozzle.
External mix air caps
produce a flat spray pattern.
• The liquid and compressed air or gas are mixed externally to produce a completely atomized spray.
C
B
A
Fluid cap
Air cap
Flat spray
pattern
6"
(15 cm)
9" (23 cm)
15" (38 cm)
D
3612
gasket
1158 retainer ring
Air Atomizing
Nozzles
Performance Data
Flat Spray (External Mix)
Spray
Set-up
No.
SUE15B
Spray
Set-up
Consists of
Fluid and
Air Cap
Combination
Fluid Cap
1650
+
Air Cap
67228-45°
Spray
Dimensions
Liquid Pressure
3
5
10
20
40
Air
Air
Air
Air
Air
A
gph scfm
gph scfm
gph scfm
gph scfm
Press.
Press.
Press.
Press.
Press.
(in.)
B
(in.)
C
(in.)
D
(ft.)
3.0
.80
.89
5.0
1.0
.93
10.0
1.4
1.1
20
2.0
1.6
40
2.8
2.6
5.0
.80
.93
10.0
1.0
1.1
15.0
1.4
1.4
25
2.0
1.9
50
2.8
3.0
3
3
3-1/2
6
9
3
15
3
3-1/2
6
9
4
10.0
.80
1.1
15.0
1.0
1.4
20
1.4
1.6
30
2.0
2.1
60
2.8
3.6
20
5
4
6
9
4
15.0
.80
1.4
20
1.0
1.6
25
1.4
1.9
40
2.0
2.6
70
2.8
4.2
20
20
4-1/2
7
10
5
20
.80
1.6
25
1.0
1.9
30
1.4
2.1
50
2.0
3.0
75
2.8
4.5
25
10
4-1/2
6
9-1/2
5
40
20
5
7
11
6
70
40
6
7
9-1/2
8
25
.80
1.9
30
1.0
2.1
40
1.4
2.6
60
2.0
3.6
80
2.8
4.9
30
.80
2.1
40
1.0
2.6
50
1.4
3.0
80
2.0
4.9
90
2.8
5.6
F15
Performance Data
Spray
Set-up
No.
SUE18B
SUE15A
SUE18A
SUE15
SUE18
Spray
Set-up
Consists of
Fluid and
Air Cap
Combination
Fluid Cap
1650
+
Air Cap
62240-60°
Fluid Cap
2050
+
Air Cap
67228-45°
Fluid Cap
2050
+
Air Cap
62240-60°
Fluid Cap
2850
+
Air Cap
67228-45°
Fluid Cap
2850
+
Air Cap
62240-60°
Spray
Dimensions
Liquid Pressure
3
5
10
20
40
Air
Air
Air
Air
Air
A
gph scfm
gph scfm
gph scfm
gph scfm
Press.
Press.
Press.
Press.
Press.
(in.)
B
(in.)
C
(in.)
D
(ft.)
11
12
14
13
12
14
15
13
16
18
17
16
19
20
4
6
6
8
9
8-1/2
9
2.8
6
8
8
15
20
15
20
5
10
20
20
20
30
40
8
9
11
11
10
11
12
4.4
2.9
5
3
3
50
4.4
3.0
20
3
3-1/2
6
2.6
60
4.4
3.6
25
5
4
6-1/2
3.1
3.0
70
4.4
4.2
25
20
5
7-1/2 11-1/2
60
3.1
3.6
75
4.4
4.5
30
10
5
7
10
6
3.0
70
3.1
4.2
90
4.4
5.6
50
20
5
8-1/2
12
8
2.2
3.6
90
3.1
5.6
95
4.4
5.8
75
40
6
7-1/2
10
10
8.0
2.2
1.0
10.0
3.1
1.2
15.0
4.4
1.6
1.2
10.0
2.2
1.2
20
3.1
1.9
20
4.4
1.9
1.6
1.6
20
2.2
1.9
30
3.1
2.5
30
4.4
2.5
20
1.6
1.9
30
2.2
2.5
35
3.1
2.8
35
4.4
2.8
10
15
10
20
35
25
25
5
10
20
20
20
30
40
11
12
15
14
13
15
16
13
15
18
17
16
18
19
16
19
23
22
20
23
26
5
7
6
8
10
9
9-1/2
1.1
15.0
3.0
1.4
20
4.2
1.6
35
6.0
2.4
50
8.4
3.0
10
3
5
6-1/2
10
4
2.3
1.4
20
3.0
1.6
25
4.2
1.9
40
6.0
2.6
60
8.4
3.6
25
3
5
6-1/2
10
6
20
2.3
1.6
25
3.0
1.9
30
4.2
2.1
50
6.0
3.0
70
8.4
4.2
30
5
5
7
9-1/2
6
25
2.3
1.9
30
3.0
2.1
40
4.2
2.6
60
6.0
3.6
75
8.4
4.5
35
20
5-1/2
8
12-1/2
6
30
2.3
2.1
40
3.0
2.6
50
4.2
3.0
70
6.0
4.2
80
8.4
4.9
40
10
5-1/2 7-1/2
12
7-1/2
40
2.3
2.6
50
3.0
3.0
60
4.2
3.6
80
6.0
4.9
90
8.4
5.6
60
20
5-1/2
8
14
10
50
2.3
3.0
60
3.0
3.6
70
4.2
4.2
90
6.0
5.6
100
8.4
6.2
75
40
6-1/2
8
12
13
6.0
2.3
.88
6.0
3.0
.88
6.0
4.2
.88
10.0
6.0
1.2
20
8.4
1.9
7.0
2.3
.97
8.0
3.0
1.0
8.0
4.2
1.0
12.0
6.0
1.4
25
8.4
2.2
8.0
2.3
1.0
9.0
3.0
1.1
10.0
4.2
1.2
15.0
6.0
1.6
30
8.4
2.5
10.0
2.3
1.2
10.0
3.0
1.2
12.0
4.2
1.4
20
6.0
1.9
35
8.4
2.8
8
8
10
15
20
25
30
5
10
20
20
20
30
40
14
14
15
16
17
16
16
19
19
19
20
21
20
20
24
25
25
26
26
27
27
6
5
6
7
8
9
9-1/2
5.0
.80
.78
5.0
1.0
.78
6.0
1.4
.88
8.0
2.0
1.0
10.0
2.8
1.2
6.0
.80
.88
6.0
1.0
.88
8.0
1.4
1.0
10.0
2.0
1.2
15.0
2.8
1.6
7.0
.80
.97
8.0
1.0
1.0
10.0
1.4
1.2
15.0
2.0
1.6
25
2.8
2.2
8.0
.80
1.0
10.0
1.0
1.2
12.0
1.4
1.4
20
2.0
1.9
35
2.8
5.0
1.2
.93
10.0
1.6
1.1
15.0
2.2
1.4
25
3.1
1.9
45
10.0
1.2
1.1
15.0
1.6
1.4
20
2.2
1.6
30
3.1
2.1
15.0
1.2
1.4
20
1.6
1.6
25
2.2
1.9
40
3.1
20
1.2
1.6
25
1.6
1.9
30
2.2
2.1
50
25
1.2
1.9
30
1.6
2.1
40
2.2
2.6
30
1.2
2.1
40
1.6
2.6
50
2.2
40
1.2
2.6
50
1.6
3.0
60
5.0
1.2
.78
5.0
1.6
.78
8.0
1.2
1.0
10.0
1.6
10.0
1.2
1.2
15.0
15.0
1.2
1.6
10.0
2.3
15.0
5-1/2 8-1/2 3-1/2
8-1/2 5-1/2
9
6
7
F16
Performance Data
SUE25B
SUE28B
SUE25A
SUE28A
SUE28
Fluid Cap
35100
+
Air Cap
134255-45°
Fluid Cap
35100
+
Air Cap
122281-60°
Fluid Cap
40100
+
Air Cap
134255-45°
Fluid Cap
40100
+
Air Cap
122281-60°
Fluid Cap
60100
+
Air Cap
122281-60°
Spray
Dimensions
Liquid Pressure
3
5
10
20
40
Air
Air
Air
Air
Air
gph scfm
gph scfm
gph scfm
gph scfm
Press.
Press.
Press.
Press.
Press.
A
(in.)
B
(in.)
C
(in.)
D
(ft.)
5-1/2
10.0
3.6
3.0
15.0
4.7
3.6
20
6.6
4.1
35
9.4
6.3
45
13.2
7.5
10
3
5
7-1/2
10
15.0
3.6
3.6
20
4.7
4.1
25
6.6
4.9
40
9.4
6.9
50
13.2
8.2
25
3
5
7-1/2
10
9
20
3.6
4.1
25
4.7
4.9
30
6.6
5.5
50
9.4
8.0
55
13.2
9.0
30
5
6
7-1/2
11
10
25
3.6
4.9
30
4.7
5.5
35
6.6
6.3
60
9.4
9.4
60
13.2
9.7
35
10
6
8-1/2
11
11-1/2
30
3.6
5.5
40
4.7
6.9
40
6.6
6.9
70
9.4
11.0
70
13.2 11.1
35
20
6-1/2
9
14
12
20
6-1/2
9
14-1/2
14
6-1/2 8-1/2 12-1/2
16
40
3.6
6.9
50
4.7
8.0
50
6.6
8.0
80
9.4
12.7
80
13.2 12.7
60
50
3.6
8.0
60
4.7
9.4
60
6.6
9.4
90
9.4
14.5
90
13.2 14.5
70
40
8.0
3.6
3.2
10.0
4.7
3.6
20
6.6
5.5
30
9.4
7.4
45
13.2 10.0
10.0
3.6
3.6
15.0
4.7
4.6
30
6.6
7.4
40
9.4
9.1
60
13.2 12.6
15.0
3.6
4.6
25
4.7
6.5
35
6.6
8.3
50
9.4
10.9
75
13.2 15.2
20
3.6
5.5
30
4.7
7.4
40
6.6
9.1
60
9.4
12.6
80
13.2 16.0
20
30
30
45
60
55
60
5
10
20
20
20
30
40
13
13
14
15
15
16
15
10.0
4.8
3.0
20
6.1
4.1
25
8.7
4.9
40
12.3
6.9
50
17.4
8.2
10
3
6
7-1/2 10-1/2
7
15.0
4.8
3.6
25
6.1
4.9
30
8.7
5.5
45
12.3
7.5
60
17.4
9.7
25
3
6
7-1/2 10-1/2
10
20
4.8
4.1
30
6.1
5.5
35
8.7
6.3
50
12.3
8.0
70
17.4 11.1
35
5
6
8-1/2
13
11
25
4.8
4.9
35
6.1
6.3
40
8.7
6.9
60
12.3
9.4
75
17.4 12.0
40
10
6
8-1/2
14
12-1/2
30
4.8
5.5
40
6.1
6.9
50
8.7
8.0
70
12.3 11.0
80
17.4 12.7
40
20
6-1/2
10
14-1/2
13
20
6-1/2
10
14-1/2
16
15
16
18
19
19
20
20
19
22
23
26
25
27
28
12-1/2
14
13
15
17
15
16
40
4.8
6.9
50
6.1
8.0
60
8.7
9.4
80
12.3 12.7
90
17.4 14.5
60
50
4.8
8.0
60
6.1
9.4
70
8.7
11.0
90
12.3 14.5
95
17.4 15.1
75
40
7
9
14
19
8.0
4.8
3.2
10.0
6.1
3.6
15.0
8.7
4.6
35
12.3
8.3
50
17.4 10.9
15.0
4.8
4.6
20
6.1
5.5
25
8.7
6.5
45
12.3 10.0
65
17.4 13.5
20
4.8
5.5
25
6.1
6.5
35
8.7
8.3
55
12.3 11.7
85
17.4 16.8
25
4.8
6.5
30
6.1
7.4
40
8.7
9.1
60
12.3 12.6
95
17.4 18.5
15
25
35
45
60
60
70
3
10
20
20
20
30
40
13
14
15
13
12
13
13
15
19
18
17
17
17
17
20
25
25
24
23
24
24
11-1/2
10
12-1/2
14
16
17
13
10.0
9.9
3.6
15.0
12.7
4.6
25
18.0
6.5
45
25.5 10.0
75
36.0 15.2
15.0
9.9
4.6
20
12.7
5.5
30
18.0
7.4
50
25.5 10.9
85
36.0 16.8
20
9.9
5.5
30
12.7
7.4
40
18.0
9.1
70
25.5 14.3
95
36.0 18.5
25
9.9
6.5
35
12.7
8.3
45
18.0 10.0
80
25.5 16.0
100
36.0 19.4
30
40
45
65
80
55
90
5
10
20
20
20
30
40
16
18
19
17
15
19
16
22
23
23
21
20
25
22
30
32
31
30
26
33
31
12
13
14
16
19
14
19
F17
Air Atomizing
Nozzles
Spray
Set-up
No.
Spray
Set-up
Consists of
Fluid and
Air Cap
Combination
Performance Data
Spray
Set-up
No.
SUE25
SUE45B
SUE45A
SUE45
Spray
Set-up
Consists of
Fluid and
Air Cap
Combination
Fluid Cap
60100
+
Air Cap
134255-45°
Fluid Cap
60150
+
Air Cap
200278-45°
Fluid Cap
80150
+
Air Cap
200278-45°
Fluid Cap
100150
+
Air Cap
200278-45°
Spray
Dimensions
Liquid Pressure
3
5
10
20
40
Air
Air
Air
Air
Air
gph scfm
gph scfm
gph scfm
gph scfm
Press.
Press.
Press.
Press.
Press.
A
(in.)
B
(in.)
C
(in.)
8
10
D
(ft.)
15.0
9.9
3.6
25
12.7
4.9
35
18.0
6.3
45
25.5
7.5
55
36.0
9.0
15
3
6
20
9.9
4.1
30
12.7
5.5
40
18.0
6.9
50
25.5
8.0
60
36.0
9.7
30
3
6
8-1/2 11-1/2
25
9.9
4.9
35
12.7
6.3
45
18.0
7.5
55
25.5
8.7
65
36.0 10.5
40
5
7
9-1/2
14
11-1/2
30
9.9
5.5
40
12.7
6.9
50
18.0
8.0
60
25.5
9.4
70
36.0 11.1
45
20
8
11
15-1/2
12
36.0 12.7
50
10
15
13
36.0 14.5
60
20
8
11
15-1/2
14
36.0 16.0
80
40
7
9-1/2
15
19-1/2
35
40
9.9
9.9
6.3
6.9
45
50
12.7
12.7
7.5
8.0
60
70
18.0
9.4
18.0 11.0
70
80
25.5 11.0
25.5 12.7
80
90
7-1/2 10-1/2
9
10
50
9.9
8.0
60
12.7
9.4
80
18.0 12.7
90
25.5 14.5
100
25
10.0
8.3
25
12.9
8.3
35
18.0 10.5
55
25.5 14.5
–
–
–
25
3
6
8
11-1/2
10
30
10.0
9.2
30
12.9
9.2
40
18.0 11.6
60
25.5 15.7
–
–
–
40
3
6
8
12
11
35
10.0 10.5
35
12.9 10.5
45
18.0 12.5
65
25.5 17.0
–
–
–
40
5
6
8
12
13
40
10.0 11.6
40
12.9 11.6
50
18.0 13.4
70
25.5 18.4
–
–
–
50
10
6-1/2 8-1/2 12-1/2
45
10.0 12.5
45
12.9 12.5
55
18.0 14.5
75
25.5 20.0
–
–
–
55
20
6-1/2 8-1/2 13-1/2
15
6-1/2
9
13
15-1/2
9
13-1/2
18
14
15
50
10.0 13.4
50
12.9 13.4
60
18.0 15.7
80
25.5 21.2
–
–
–
60
60
10.0 15.7
60
12.9 15.7
70
18.0 18.4
90
25.5 24.2
–
–
–
70
20
6-1/2
30
17.4
9.2
40
22.5 11.6
55
31.5 14.5
70
44.7 18.4
–
–
–
30
3
6-1/2 9-1/2 13-1/2 11-1/2
35
17.4 10.5
45
22.5 12.5
60
31.5 15.7
75
44.7 20.0
–
–
–
45
3
7
9-1/2
14
14
40
17.4 11.6
50
22.5 13.4
65
31.5 17.0
80
44.7 21.2
–
–
–
55
5
7
10
14
16
45
17.4 12.5
55
22.5 14.5
70
31.5 18.4
85
44.7 22.5
–
–
–
70
10
7
10
14
18
50
17.4 13.4
60
22.5 15.7
75
31.5 20.0
90
44.7 24.2
–
–
–
70
20
8
10
15
18
60
17.4 15.7
70
22.5 18.4
80
31.5 21.2
–
–
–
–
75
15
7
10
15
19
20
8
10
15
20
–
–
–
–
80
72.0 21.2
–
–
–
40
3
7-1/2
10
14
15
72.0 22.5
–
–
–
55
3
8
10
14-1/2
16
72.0 24.2
–
–
–
65
5
8
10
14-1/2
17
–
–
–
–
75
10
8-1/2 10-1/2
15
18
–
–
–
–
–
80
15
8-1/2 10-1/2
16
18
–
–
–
–
–
–
80
20
8-1/2 10-1/2
16
19
–
–
–
–
–
–
85
20
8-1/2 10-1/2
16
20
70
17.4 18.4
80
22.5 21.2
90
31.5 24.2
–
40
27.9 11.6
50
36.0 13.4
65
50.6 17.0
80
45
27.9 12.5
55
36.0 14.5
70
50.6 18.4
85
50
27.9 13.4
60
36.0 15.7
75
50.6 20.0
90
55
27.9 14.5
65
36.0 17.0
80
50.6 21.2
–
–
60
27.9 15.7
70
36.0 18.5
85
50.6 22.5
–
65
27.9 17.0
75
36.0 20.0
90
50.6 24.2
70
27.9 18.4
80
36.0 21.2
–
–
–
–
–
–
F18
High Transfer Efficiency (HTE), 1/4J Series
C
B
A
Flat spray
pattern
• A new air cap design enables the use of lower air pressures to achieve
the same spray performance as conventional external mix set-ups.
6" (15 cm)
9" (23 cm)
15" (38 cm)
• HTE set-ups operate at pressures as low as 5 psi (0.3 bar).
• A large air chamber directly feeds the air exit orifices. Design provides
high liquid transfer efficiency, minimal air loss, and minimal misting.
D
• Air consumption is reduced and maximum spray coverage on the target
is achieved.
C
• See also
B
A
Round spray
pattern
– Section G, Automatic Spray Nozzles
Air Caps
6" (15 cm)
9" (23 cm)
15" (38 cm)
D
Air Atomizing
Nozzles
1158 retainer ring and 3612 gasket must be ordered separately
from the spray set-up, but are included in the standard nozzle
assembly. Please contact your sales engineer.
HTE air cap produces a flat
spray and a round spray.
Performance Data
Spray
Set-up
No.
Spray
Set-up
Consists of
Fluid and
Air Cap
Combination
Fluid Cap
PF28100
SU-HTE60D
+
Air Cap
LP130262-60
Fluid Cap
PF20100
SU-HTE60E
+
Air Cap
LP130262-60
SU-HTE60F
Fluid Cap
PF16100
+
Air Cap
LP130262-60
Spray
Dimensions
Liquid Pressure
5
10
15
20
30
Air
Air
Air
Air
Air
A
gph scfm
gph scfm
gph scfm
gph scfm
Press.
Press.
Press.
Press.
Press.
(in.)
8.0
10.0
12.0
14.0
16.0
6.0
8.0
10.0
12.0
14.0
16.0
4.0
6.0
8.0
10.0
12.0
14.0
16.0
3.0
3.0
3.0
3.0
3.0
1.6
1.6
1.6
1.6
1.6
1.6
1.0
1.0
1.0
1.0
1.0
1.0
1.0
3.3
3.8
4.2
4.5
4.9
2.8
3.3
3.8
4.2
4.5
4.9
2.3
2.8
3.3
3.8
4.2
4.5
4.9
8.0
10.0
12.0
14.0
16.0
6.0
8.0
10.0
12.0
14.0
16.0
–
–
8.0
10.0
12.0
14.0
16.0
4.2
4.2
4.2
4.2
4.2
2.2
2.2
2.2
2.2
2.2
2.2
–
–
1.4
1.4
1.4
1.4
1.4
3.3
3.8
4.2
4.5
4.9
2.8
3.3
3.8
4.2
4.5
4.9
–
–
3.3
3.8
4.2
4.5
4.9
–
10.0
12.0
14.0
16.0
–
8.0
10.0
12.0
14.0
16.0
–
–
8.0
10.0
12.0
14.0
16.0
–
5.1
5.1
5.1
5.1
–
2.6
2.6
2.6
2.6
2.6
–
–
1.7
1.7
1.7
1.7
1.7
–
3.8
4.2
4.5
4.9
–
3.3
3.8
4.2
4.5
4.9
–
–
3.3
3.8
4.2
4.5
4.9
–
–
12.0
14.0
16.0
–
–
10.0
12.0
14.0
16.0
–
–
8.0
10.0
12.0
14.0
16.0
–
–
6.0
6.0
6.0
–
–
3.1
3.1
3.1
3.1
–
–
2.0
2.0
2.0
2.0
2.0
–
–
4.2
4.5
4.9
–
–
3.8
4.2
4.5
4.9
–
–
3.3
3.8
4.2
4.5
4.9
–
–
–
14.0
16.0
–
–
–
–
14.0
16.0
–
–
–
–
12.0
14.0
16.0
–
–
–
7.2
7.2
–
–
–
–
3.7
3.7
–
–
–
–
2.4
2.4
2.4
–
–
–
4.5
4.9
–
–
–
–
4.5
4.9
–
–
–
–
4.2
4.5
4.9
B
(in.)
C
(in.)
D
(in.)
14
8
13
10
11
36
40
40
45
41
10
15
10
15
10
5
5
10
10
20
7
13
5
6
11-1/2 13-1/2
6
9
10
15
5
10
15
5
10
15
5
5
5
10
10
10
7
9
11
4
4-1/2 4-1/2
3
4-1/2 5-1/2
8
11
13
8
9
9
6-1/2
7
7-1/2
25
31
34
22
27
32
3
5
10
15
5
10
15
5
5
5
5
10
10
10
9-1/2
11
13
9
10
12
8
9
11-1/2
6-1/2 7-1/2 8-1/2
8-1/2 9-1/2
12
7-1/2
9
11
6
7-1/2 9-1/2
23
24
25
28
22
25
29
Add DF to part number for “Drip Free™” set-ups. Example: SU-HTE60D-DF.
The operating pressures and flow rates are based on spraying water and air at room temperature.
Adjustments may need to be made to accommodate other liquids with different characteristics.
F19
Performance Data
Spray
Set-up
No.
Spray
Set-up
Consists of
Fluid and
Air Cap
Combination
Fluid Cap
PF35100
SU-HTE61C
+
Air Cap
LP130285-60
Fluid Cap
PF28100
SU-HTE61D
+
Air Cap
LP130285-60
Fluid Cap
PF20100
SU-HTE61E
+
Air Cap
LP130285-60
SU-HTE61F
Fluid Cap
PF16100
+
Air Cap
LP130285-60
Fluid Cap
PF28100
SU-HTE62D
+
Air Cap
LP120262-90
Fluid Cap
PF20100
SU-HTE62E
+
Air Cap
LP120262-90
Spray
Dimensions
Liquid Pressure
5
10
15
20
30
Air
Air
Air
Air
Air
A
gph scfm
gph scfm
gph scfm
gph scfm
Press.
Press.
Press.
Press.
Press.
(in.)
6.0
4.7
3.5
–
–
–
–
–
–
–
–
–
–
–
–
8.0
4.7
4.2
8.0
6.6
4.2
–
–
–
–
–
–
–
–
–
10.0
4.7
4.7
10.0
6.6
4.7
–
–
–
–
–
–
–
–
–
12.0
4.7
5.3
12.0
6.6
5.3
12.0
8.1
5.3
–
–
–
–
–
–
14.0
4.7
5.8
14.0
6.6
5.8
14.0
8.1
5.8
14.0
9.4
5.8
14.0
11.4
5.8
16.0
4.7
6.2
16.0
6.6
6.2
16.0
8.1
6.2
16.0
9.4
6.2
16.0
11.4
6.2
6.0
3.0
3.5
–
–
–
–
–
–
–
–
–
–
–
–
8.0
3.0
4.2
8.0
4.2
4.2
–
–
–
–
–
–
–
–
–
10.0
3.0
4.7
10.0
4.2
4.7
10.0
5.1
4.7
–
–
–
–
–
–
12.0
3.0
5.3
12.0
4.2
5.3
12.0
5.1
5.3
–
–
–
–
–
–
14.0
3.0
5.8
14.0
4.2
5.8
14.0
5.1
5.8
14.0
6.0
5.8
14.0
7.2
5.8
16.0
3.0
6.2
16.0
4.2
6.2
16.0
5.1
6.2
16.0
6.0
6.2
16.0
7.2
6.2
4.0
1.6
2.8
–
–
–
–
–
–
–
–
–
–
–
–
6.0
1.6
3.5
–
–
–
–
–
–
–
–
–
–
–
–
8.0
1.6
4.2
8.0
2.2
4.2
8.0
2.6
4.2
–
–
–
–
–
–
10.0
1.6
4.7
10.0
2.2
4.7
10.0
2.6
4.7
10.0
3.1
4.7
10.0
3.7
4.7
12.0
1.6
5.3
12.0
2.2
5.3
12.0
2.6
5.3
12.0
3.1
5.3
12.0
3.7
5.3
14.0
1.6
5.8
14.0
2.2
5.8
14.0
2.6
5.8
14.0
3.1
5.8
14.0
3.7
5.8
16.0
1.6
6.2
16.0
2.2
6.2
16.0
2.6
6.2
16.0
3.1
6.2
16.0
3.7
6.2
4.0
1.0
2.8
–
–
–
–
–
–
–
–
–
–
–
–
6.0
1.0
3.5
6.0
1.4
3.5
–
–
–
–
–
–
–
–
–
8.0
1.0
4.2
8.0
1.4
4.2
8.0
1.7
4.2
8.0
2.0
4.2
–
–
–
10.0
1.0
4.7
10.0
1.4
4.7
10.0
1.7
4.7
10.0
2.0
4.7
10.0
2.4
4.7
12.0
1.0
5.3
12.0
1.4
5.3
12.0
1.7
5.3
12.0
2.0
5.3
12.0
2.4
5.3
14.0
1.0
5.8
14.0
1.4
5.8
14.0
1.7
5.8
14.0
2.0
5.8
14.0
2.4
5.8
16.0
1.0
6.2
16.0
1.4
6.2
16.0
1.7
6.2
16.0
2.0
6.2
16.0
2.4
6.2
4.0
3.0
2.0
–
–
–
–
–
–
–
–
–
–
–
–
6.0
3.0
2.5
6.0
4.2
2.5
–
–
–
–
–
–
–
–
–
–
8.0
3.0
2.9
8.0
4.2
2.9
8.0
5.1
2.9
–
–
–
–
–
10.0
3.0
3.3
10.0
4.2
3.3
10.0
5.1
3.3
10.0
6.0
3.3
–
–
–
12.0
3.0
3.6
12.0
4.2
3.6
12.0
5.1
3.6
12.0
6.0
3.6
12.0
7.2
3.6
14.0
3.0
4.0
14.0
4.2
4.0
14.0
5.1
4.0
14.0
6.0
4.0
14.0
7.2
4.0
16.0
3.0
4.3
16.0
4.2
4.3
16.0
5.1
4.3
16.0
6.0
4.3
16.0
7.2
4.3
4.0
1.6
2.0
–
–
–
–
–
–
–
–
–
–
–
–
6.0
1.6
2.5
–
–
–
–
–
–
–
–
–
–
–
–
–
8.0
1.6
2.9
8.0
2.2
2.9
–
–
–
–
–
–
–
–
10.0
1.6
3.3
10.0
2.2
3.3
10.0
2.6
3.3
10.0
3.1
3.3
–
–
–
12.0
1.6
3.6
12.0
2.2
3.6
12.0
2.6
3.6
12.0
3.1
3.6
12.0
3.7
3.6
14.0
1.6
4.0
14.0
2.2
4.0
14.0
2.6
4.0
14.0
3.1
4.0
14.0
3.7
4.0
16.0
1.6
4.3
16.0
2.2
4.3
16.0
2.6
4.3
16.0
3.1
4.3
16.0
3.7
4.3
5
10
15
10
15
10
5
5
5
10
10
20
5
10
15
5
10
15
5
5
5
10
10
10
3
5
10
15
5
10
15
B
(in.)
C
(in.)
10-1/2 14
20
9 11-1/2 12
6-1/2
9
12
10-1/2 14 16-1/2
9
11
13
12
16 20-1/2
7
5
4
9
6
5
D
(in.)
27
37
43
37
43
35
7
8
6
7-1/2
5
6-1/2
11
12
8-1/2
9
6
8
29
36
57
33
37
43
5
5
5
5
10
10
10
8
10
14
7
7-1/2
9
3-1/2
5
6
3-1/2
4
5-1/2
9-1/2 10 11-1/2
7
8
9
6
7-1/2 9-1/2
18
24
29
30
27
35
39
3
5
10
15
5
10
15
5
5
5
5
10
10
10
10
8-1/2
7
7-1/2
11
8-1/2
8-1/2
12-1/2 14-1/2
10
12
9-1/2 12
10
11
12-1/2 15
10-1/2 11-1/2
10 11-1/2
29
33
34
33
32
33
33
3
5
10
15
10
10
20
5
5
5
5
10
15
10
7
11
11
7
14
16
13
11
16
12-1/2 14
13 13-1/2
7
8
15
17
16
18
17
16
34
38
42
45
40
50
48
3
5
10
15
5
10
15
5
5
5
5
10
10
10
10 13-1/2 15
7-1/2 9-1/2 10
7
8
8-1/2
6
6-1/2
7
7-1/2 11 11-1/2
6-1/2
9
10
6-1/2
8
8-1/2
21
28
33
39
26
29
37
F20
Performance Data
SU-HTE62F
SU-HTE64C
SU-HTE64D
SU-HTE64E
SU-HTE64F
Fluid Cap
PF16100
+
Air Cap
LP120262-90
Fluid Cap
PF35100
+
Air Cap
LP130210060
Fluid Cap
PF28100
+
Air Cap
LP130210060
Fluid Cap
PF20100
+
Air Cap
LP130210060
Fluid Cap
PF16100
+
Air Cap
LP130210060
Spray
Dimensions
Liquid Pressure
5
10
15
20
30
Air
Air
Air
Air
Air
A
gph scfm
gph scfm
gph scfm
gph scfm
Press.
Press.
Press.
Press.
Press.
(in.)
B
(in.)
C
(in.)
D
(in.)
11
12-1/2
26
8-1/2 9-1/2 10-1/2
28
4.0
1.0
2.0
–
–
–
–
–
–
–
–
–
–
–
–
3
5
6.0
1.0
2.5
6.0
1.4
2.5
–
–
–
–
–
–
–
–
–
5
5
8.0
1.0
2.9
8.0
1.4
2.9
8.0
1.7
2.9
8.0
2.0
2.9
–
–
–
10
5
10.0
1.0
3.3
10.0
1.4
3.3
10.0
1.7
3.3
10.0
2.0
3.3
10.0
2.4
3.3
15
5
3.6
5
10
9
4.0
10
10
15
12.0
14.0
1.0
1.0
3.6
4.0
12.0
14.0
1.4
1.4
3.6
4.0
12.0
14.0
1.7
1.7
3.6
4.0
12.0
14.0
2.0
2.0
3.6
4.0
12.0
14.0
2.4
2.4
9
6
7-1/2 8-1/2
6-1/2 7-1/2
24
9
25
11
12-1/2
26
8
9
12
26
10
7-1/2
9
11
26
16.0
1.0
4.3
16.0
1.4
4.3
16.0
1.7
4.3
16.0
2.0
4.3
16.0
2.4
4.3
6.0
4.7
4.0
–
–
–
–
–
–
–
–
–
–
–
–
5
5
12
16
19
30
8.0
4.7
4.7
8.0
6.6
4.7
–
–
–
–
–
–
–
–
–
10
5
11
11-1/2
15
34
10.0
4.7
5.3
10.0
6.6
5.3
–
–
–
–
–
–
–
–
–
15
5
6
9
10
44
12.0
4.7
5.9
12.0
6.6
5.9
12.0
8.1
5.9
–
–
–
–
–
–
5
10
14
16
19
29
14.0
4.7
6.5
14.0
6.6
6.5
14.0
8.1
6.5
14.0
9.4
6.5
14.0
11.4
6.5
10
10
12
16
18
35
15
10
8
12
13
41
16.0
4.7
7.1
6.0
3.0
4.0
–
8.0
3.0
4.7
8.0
10.0
3.0
5.3
10.0
4.2
12.0
14.0
3.0
3.0
5.9
6.5
16.0
12.0
14.0
6.6
7.1
16.0
8.1
7.1
16.0
9.4
7.1
16.0
11.4
7.1
–
–
–
–
–
–
–
–
–
–
–
5
5
11
13
14
39
4.2
4.7
–
–
–
–
–
–
–
–
–
10
5
8
10
13
40
5.3
10.0
5.1
5.3
–
–
–
–
–
–
15
5
7
8
11
50
–
5
10
11
12
18
30
6.5
10
10
8
11
14
41
10
7
8
13
53
7
9
11
23
4.2
4.2
5.9
6.5
12.0
14.0
5.1
5.1
5.9
6.5
–
14.0
–
6.0
–
6.5
–
14.0
–
7.2
16.0
3.0
7.1
16.0
4.2
7.1
16.0
5.1
7.1
16.0
6.0
7.1
16.0
7.2
7.1
15
4.0
1.6
3.2
–
–
–
–
–
–
–
–
–
–
–
–
3
5
6.0
1.6
4.0
–
–
–
–
–
–
–
–
–
–
–
–
5
5
8.0
1.6
4.7
8.0
2.2
4.7
8.0
2.6
4.7
–
–
–
–
–
–
10
5
5
5
6
33
10.0
1.6
5.3
10.0
2.2
5.3
10.0
2.6
5.3
10.0
3.1
5.3
10.0
3.7
5.3
15
5
5
5
5-1/2
39
12.0
1.6
5.9
12.0
2.2
5.9
12.0
2.6
5.9
12.0
3.1
5.9
12.0
3.7
5.9
5
10
7-1/2 8-1/2
9
29
6.5
10
10
5-1/2 6-1/2 7-1/2
35
10
5-1/2 6-1/2
7
43
14.0
1.6
6.5
14.0
14.0
2.6
6.5
14.0
3.1
6.5
14.0
3.7
7.1
16.0
2.6
7.1
16.0
3.1
7.1
16.0
3.7
7.1
–
–
–
–
–
–
–
–
–
–
–
3
5
9
11
13-1/2
27
1.4
4.0
–
–
–
–
–
–
–
–
–
5
5
7
9
11-1/2
27
1.4
4.7
8.0
1.7
4.7
8.0
2.0
4.7
–
–
–
10
5
6-1/2
8
10
30
10.0
1.4
5.3
10.0
1.7
5.3
10.0
2.0
5.3
10.0
2.4
5.3
15
5
5-1/2
7
8-1/2
30
5.9
12.0
1.4
5.9
12.0
1.7
5.9
12.0
2.0
5.9
12.0
2.4
5.9
5
10
9
11
13-1/2
28
6.5
14.0
1.4
6.5
14.0
1.7
6.5
14.0
2.0
6.5
14.0
2.4
6.5
10
10
7-1/2
9
10
29
7.1
15
10
5-1/2
7
8-1/2
29
1.6
7.1
4.0
1.0
3.2
–
6.0
1.0
4.0
6.0
8.0
1.0
4.7
8.0
10.0
1.0
5.3
12.0
1.0
14.0
1.0
1.0
6.5
25
15
16.0
16.0
2.2
6-1/2 6-1/2 8-1/2
7.1
16.0
16.0
2.2
1.4
7.1
16.0
1.7
7.1
16.0
2.0
7.1
16.0
2.4
F21
Air Atomizing
Nozzles
Spray
Set-up
No.
Spray
Set-up
Consists of
Fluid and
Air Cap
Combination
Performance Data
Round Spray (External Mix)
Spray
Set-up
No.
Spray
Set-up
Consists of
Fluid and
Air Cap
Combination
SU-HTE91A
Fluid Cap
PF2850
+
Air Cap
LP60650-60
SU-HTE91B
Fluid Cap
PF2050
+
Air Cap
LP60650-60
SU-HTE91C
Fluid Cap
PF1650
+
Air Cap
LP60650-60
Spray
Dimensions
Liquid Pressure
5
10
15
20
30
Air
Air
Air
Air
Air
A
gph scfm
gph scfm
gph scfm
gph scfm
Press.
Press.
Press.
Press.
Press.
(in.)
4.0
6.0
8.0
10.0
12.0
14.0
16.0
4.0
6.0
8.0
10.0
12.0
14.0
16.0
6.0
8.0
10.0
12.0
14.0
16.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.0
1.0
1.0
1.0
1.0
1.0
1.9
2.5
2.9
3.4
3.8
4.1
4.5
1.9
2.5
2.9
3.4
3.8
4.1
4.5
2.5
2.9
3.4
3.8
4.1
4.5
–
6.0
8.0
10.0
12.0
14.0
16.0
–
–
8.0
10.0
12.0
14.0
16.0
–
8.0
10.0
12.0
14.0
16.0
–
4.2
4.2
4.2
4.2
4.2
4.2
–
–
2.2
2.2
2.2
2.2
2.2
–
1.4
1.4
1.4
1.4
1.4
–
2.5
2.9
3.4
3.8
4.1
4.5
–
–
2.9
3.4
3.8
4.1
4.5
–
2.9
3.4
3.8
4.1
4.5
–
–
8.0
10.0
12.0
14.0
16.0
–
–
–
10.0
12.0
14.0
16.0
–
–
–
–
14.0
16.0
–
–
5.1
5.1
5.1
5.1
5.1
–
–
–
2.6
2.6
2.6
2.6
–
–
–
–
1.7
1.7
–
–
2.9
3.4
3.8
4.1
4.5
–
–
–
3.4
3.8
4.1
4.5
–
–
–
–
4.1
4.5
–
–
8.0
10.0
12.0
14.0
16.0
–
–
–
10.0
12.0
14.0
16.0
–
–
–
–
14.0
16.0
–
–
6.0
6.0
6.0
6.0
6.0
–
–
–
3.1
3.1
3.1
3.1
–
–
–
–
2.0
2.0
–
–
2.9
3.4
3.8
4.1
4.5
–
–
–
3.4
3.8
4.1
4.5
–
–
–
–
4.1
4.5
–
–
8.0
10.0
12.0
14.0
16.0
–
–
–
–
–
14.0
16.0
–
–
–
–
–
–
–
–
7.2
7.2
7.2
7.2
7.2
–
–
–
–
–
3.7
3.7
–
–
–
–
–
–
–
–
2.9
3.4
3.8
4.1
4.5
–
–
–
–
–
4.1
4.5
–
–
–
–
–
–
B
(in.)
C
(in.)
D
(in.)
3
5
10
15
5
10
15
5
5
5
5
10
10
10
1
3-1/2
2
2
2-1/2
1-1/2
1
3
3-1/2
3-1/2
5
3-1/2
4
3-1/2
5
4-1/2 5-1/2
2-1/2 3-1/2
2-1/2
4
44
40
43
44
39
41
47
3
5
10
15
5
10
15
5
5
5
5
10
10
10
2
3-1/2 4-1/2
2-1/2
3
3-1/2
2
3-1/2
5
2
3
5
2-1/2
3
3-1/2
2
3-1/2
5
2
3
5
41
42
42
49
42
42
49
5
10
15
5
10
15
5
5
5
10
10
10
3-1/2
4
5
4
4-1/2 5-1/2
4
5
6
2
4
4-1/2
3
4
4-1/2
3
3-1/2
5
34
38
46
35
38
52
Ordering Info
Nozzle Body*
1/4
l
Inlet
Conn.
Spray Set-up Only
Spray Set-up
Spray Set-up
J – SS + SU-HTE60D – SS
l
l
l
l
Nozzle
No.
Material
Code
Spray
Set-up Number
Material
Code
HTE60D –
l
Spray
Set-up Number
SS
l
Material
Code
BSPT connections require the addition of a “B” prior to the nozzle body inlet connection.
*To order fluid cap only, use fluid cap number (shown in performance data charts and material code).
To order air cap only, use air cap number (shown in performance data charts and material code).
To order spray nozzle without set-up, use inlet connection, nozzle body and material code.
To order Drip Free set-ups, add DF after set-up number: SU-HTE60D-DF – SS.
F22
Siphon/Gravity-Fed Spray Set-ups,
External Mix, 1/8J and 1/4J Series
Air Caps
• For round and flat sprays, angle “A” is maintained throughout distance “B”. Beyond “B”, the spray
• When using a siphon or gravity-fed liquid system, the liquid is supplied by either a liquid siphon or a
gravity-feed.
Round spray and flat spray
air caps produce round spray
and flat spray patterns.
• Designed to draw liquid through the feed line into the air flow where it is atomized.
Round spray
pattern
A
B
D
1158 retainer ring and 3612 gasket must be ordered separately from the spray set-up, but are
included in the standard nozzle assembly. Please contact your sales engineer.
Air Atomizing
Nozzles
Refer to page F3 for Siphon/Gravity-Fed Spray Set-ups diagram.
Performance Data
Flat Spray
Spray
Set-up
No.
SUF1
SUF2C
SUF3B
SUF4B
Spray
Set-up
Consists of
Fluid and
Air Cap
Combination
Fluid Cap 2850
+
Air Cap 73420
Fluid Cap 35100
+
Air Cap 120432
Fluid Cap 40100
+
Air Cap 122435
Fluid Cap 40100
+
Air Cap 122440
Atomizing
Air
Liquid Capacity
(gallons per hour)*
Spray Dimensions
at 8" Siphon Height
Air
Capacity
scfm
18
12
6
4
8
12
24
36
10.0
.99
.35
.33
.30
.27
.25
.22
.17
.13
20
1.42
.31
.30
.29
.26
.25
.23
.19
.16
30
1.83
.18
.16
.15
.11
.09
–
–
–
20
1.86
1.01
.95
.90
.77
.72
.67
.62
.56
30
2.42
.88
.84
.81
.75
.71
.67
.63
.57
40
2.96
.76
.73
.69
.65
.61
.58
.53
.48
60
4.05
.44
.41
.37
.33
.30
.27
–
20
2.26
1.35
1.28
1.20
1.01
.96
.92
.78
30
2.88
1.26
1.21
1.14
.92
.87
.82
.74
.59
40
3.52
.98
.92
.87
.66
.59
.52
.44
–
50
4.13
.58
.52
.44
–
–
–
–
20
2.10
2.01
1.90
1.71
1.47
1.40
1.32
30
2.70
2.00
1.94
1.81
1.58
1.52
40
3.28
1.82
1.74
1.63
1.42
50
3.87
1.10
.97
.85
.69
Air
Press.
Gravity Head (in.)
Siphon Height (in.)
Air*
A
(in.)
B
(in.)
C
(in.)
D
(ft.)
10
20
30
8
8-1/2
9
10-1/2
11-1/2
12
15
15
15
7
7
6
–
20
30
40
60
9
9-1/2
10-1/2
11
12-1/2
15
13-1/2 16-1/2
14-1/2
18
15-1/2
19
.62
20
7-1/2
9
10-1/2
11
30
8
10
11
11
–
40
8-1/2
10-1/2
12
10
1.17
.92
20
6-1/2
8-1/2
10-1/2
11
1.45
1.34
1.11
1.34
1.22
1.03
–
30
7
9
11-1/2
11
–
–
–
–
40
8
10-1/2
13
11
9
9
10
9
F23
External Mix, 1/8J and 1/4J Series
Performance Data
Round Spray
Spray
Set-up
No.
SU1A
SU1
SU2A
SU2
SU4
SU5
Spray
Set-up
Consists of
Fluid and
Air Cap
Combination
Fluid Cap 1650
+
Air Cap 64
Fluid Cap 2050
+
Air Cap 64
Fluid Cap 2050
+
Air Cap 70
Fluid Cap 2850
+
Air Cap 70
Fluid Cap 60100
+
Air Cap 120
Fluid Cap 100150
+
Air Cap 180
Atomizing
Air
Liquid Capacity
(gallons per hour)*
Spray Dimensions
at 8" Siphon Height
Air
Press.
Air
Capacity
scfm
18
12
6
4
8
12
10.0
.40
.39
.35
.30
.23
.18
20
.59
.46
.43
.39
.34
.31
40
.95
.54
.50
.47
.41
Gravity Head (in.)
Siphon Height (in.)
Air*
Spray
Angle
A (°)
B
(in.)
D
(ft.)
24
36
.14
–
–
10
18
11
6
.28
.14
–
20
18
11
6-1/2
.38
.36
.28
.19
40
18
12
7-1/2
8-1/2
60
1.32
.59
.54
.49
.44
.41
.39
.31
.24
60
18
14
10.0
.47
.63
.55
.46
.40
.32
.21
–
–
10
18
12
7
20
.66
.73
.66
.60
.54
.48
.40
.21
.07
20
18
13
7-1/2
40
1.06
.87
.81
.76
.71
.67
.61
.43
.28
40
18
15
8-1/2
60
1.48
.98
.92
.88
.83
.79
.73
.57
.40
60
19
17
10
10.0
.81
.67
.61
.53
.43
.37
.29
–
–
10
18
12
8
20
1.20
.76
.72
.64
.56
.50
.44
.21
–
20
18
13
9
40
1.94
.89
.86
.82
.76
.71
.65
.46
.30
40
19
15
11
60
2.70
.98
.96
.94
.91
.87
.81
.68
.56
60
20
17
13
10.0
.68
1.19
1.05
.91
.56
.47
.38
–
–
10
21
15
10
20
1.03
1.37
1.27
1.13
.88
.77
.68
.46
–
20
21
16
11
40
1.70
1.57
1.47
1.32
1.15
1.05
.91
.63
.28
40
21
18
13
60
2.39
1.48
1.41
1.30
1.08
1.02
.90
.74
.52
60
22
20
15
20
1.90
5.80
5.15
4.20
3.10
2.65
1.90
.60
–
20
17
18
12
40
3.00
6.50
5.95
5.10
4.30
3.70
3.00
1.55
.70
40
18
20
14
60
4.10
6.80
6.35
5.60
4.90
4.20
3.45
2.20
1.30
60
18
21
16
80
5.20
6.80
6.40
5.80
5.20
4.50
3.85
2.60
1.60
80
19
23
18
30
5.3
–
–
–
7.2
6.0
4.6
–
–
30
20
20
22
40
6.5
–
–
–
7.8
6.8
5.3
–
–
40
20
21
23
60
8.8
–
11.4
10.6
8.3
7.4
6.2
3.2
–
60
21
23
25
80
11.1
11.6
11.0
10.3
8.3
7.5
6.4
4.4
2.2
80
22
25
27
F24
Overview, 1/8JJ Compact Series
1/8JJ Series air atomizing
Spray set-up
1/8JJ
1
2
3
4
5
Spray set-up
1/8JJCO
Clean-out
1
2
3
4
7
6
1/8JJN
2. Air cap
3. Fluid cap
4. O-ring 7717-2/007
7. Back Seal Gasket 7222-BUC
Shut-off
1/8JJAU – Drip Free
Shut-off/clean-out
needle assembly
Applying lubricant to form presses in steel drum manufacturing.
F25
Air Atomizing
Nozzles
Spray Set-up for Drip Free™
Optimization Tips
• Nozzle assembly consists of a body and spray set-up.
• Various assemblies can be added to provide shut-off or
clean-out functions.
See Also
• 1/8JJ has liquid and air feeds at opposite ends of the body.
• 1/8JJN features a manual shut-off needle that enables the flow
of liquid to be stopped.
• Accessories
• 1/8JJCO features a clean-out needle that is activated manually.
– Needle slides through the liquid orifice to clear obstructions.
– Ideal for intermittent spraying applications when liquid can
dry in the orifice between uses.
1/8JJ
1/8JJN
1/8" NPT or BSPT
Material
– Pressure gauges
– Solenoid valves
– Strainers
1/8JJCO
1/8" NPT or BSPT with
shut-off needle
Materials
http://
clean-out needle
Ordering Info
Nozzle Type
Material
Code
JJ JJN JJCO
Nozzle Body*
Spray Set-up Only
Spray Set-up
Spray Set-up
1/8 JJN – SS + SUJ12A – SS
Nozzle Bodies
Electroless Nickelplated Brass
(none)
l
l
l
303 Stainless Steel
SS
l
l
l
Spray Set-ups
l
l
l
l
l
Inlet
Conn.
Nozzle
Body
Assembly
Type
Material
Code
Spray
Set-up
No.
Material
Code
Electroless Nickelplated Brass Air
Cap and
303 Stainless Steel
Fluid Cap
SSBR
303 Stainless Steel
SS
l
l
l
SUJ12A
l
Spray
Set-up
No.
–
SS
l
Material
Code
To order spray set-up only,
use spray set-up number and
material code: SU12A-SS.
performance data charts) and material code: J2050-SS.
l
l
l
performance data charts) and material code: J73160-SS.
connection, nozzle body and material code: 1/8JJN-SS.
F26
Air Caps
• For round spray pattern, angle “A” is maintained throughout distance “B”. Beyond “B”, the spray
Round spray and 360° circular
spray air caps produce full cone
round spray; air caps used in
spray set-up SUJ340C produce
360° circular spray pattern.
Round spray
pattern
A
B
D
12582 retainer ring and 7717-2/007 O-ring must be ordered separately from the spray set-up, but are included in
Round Spray
Spray
Set-up
No.
Spray
Set-up
Consists of
Fluid and
Air Cap
Combination
SUJ11
Fluid Cap
J2050
+
Air Cap
J67147
SUJ12A
Fluid Cap
J2050
+
Air Cap
J73160
Air Atomizing
Nozzles
Performance Data
Spray
Dimensions
Liquid Pressure
10
20
30
40
60
Air*
Air
Air
Air
Air
Air
gph scfm
gph scfm
gph scfm
gph scfm
gph scfm
Press.
Press.
Press.
Press.
Press.
Liquid*
Spray
Angle
A (°)
B
(in.)
D
(ft.)
10.0
.66
.55
14
1.50
.40
24
1.68
.56
32
1.86
.68
50
2.28
.98
12
10
13
12
9
12.0
.48
.67
18
1.23
.50
28
1.44
.63
36
1.62
.80
54
2.05 1.07
24
20
13
13
10
14.0
.36
.78
22
.99
.63
32
1.08
.82
40
1.32
.93
58
1.80 1.19
36
30
13
14
11
40
14
15-1/2
12-1/2
–
–
–
26
.72
.76
38
.72
1.03
48
.85
1.23
66
1.32 1.52
44
–
–
–
30
.45
.93
42
.54
1.19
52
.66
1.38
70
1.11 1.66
62
60
15
17-1/2
14-1/2
10.0
.66
.66
18
1.44
.87
24
1.98 1.00
30
2.40 1.14
40
3.30 1.36
12
10
12
17
12
12.0
.54
.77
20
1.32
.98
28
1.68 1.17
34
2.16 1.29
46
2.94 1.54
20
20
13
18
13
14.0
.42
.90
22
1.20 1.06
32
1.44 1.35
38
1.92 1.47
52
2.58 1.83
34
30
13
19
14
–
–
–
26
.90
1.26
36
1.20 1.57
44
1.50 1.78
62
2.10 2.26
42
40
13
20
15
–
–
–
–
–
–
40
1.02 1.76
48
1.32 1.98
70
1.68 2.67
58
60
15
22
17
F27
Performance Data
Round Spray
Spray
Set-up
No.
Spray
Set-up
Consists of
Fluid and
Air Cap
Combination
SUJ12
Fluid Cap
J2850
+
Air Cap
J73160
SUJ22B
SUJ22
Fluid Cap
J40100
+
Air Cap
J1401110
Fluid Cap
J60100
+
Air Cap
J1401110
10
20
30
40
60
Air* Liquid*
Air
Air
Air
Air
Air
gph scfm
gph scfm
gph scfm
gph scfm
gph scfm
Press.
Press.
Press.
Press.
Press.
Spray
Set-up
No.
SUJ340C
Fluid Cap
J60100
+
Air Cap
J150-6-62160HC
Spray
Angle
A (°)
B
(in.)
D
(ft.)
12.0
1.26
.73
22
2.16 1.05
30
2.90 1.24
36
4.32 1.26
48
5.82 1.50
22
10
12
19
13
16.0
1.08
.94
26
1.74 1.26
34
2.46 1.42
40
3.85 1.36
52
5.28 1.65
34
20
13
20
14
20
.90
1.15
30
1.44 1.47
38
2.10 1.65
44
3.55 1.56
56
4.92 1.73
42
30
13
21
15
24
.78
1.36
38
1.08 1.87
46
1.50 2.03
52
2.46 2.01
64
4.08 2.08
48
40
14
22
16
60
15
23-1/2
17-1/2
1.56
42
.94
2.04
52
1.20 2.36
60
1.86 2.36
70
3.60 2.34
60
16.0
3.44 2.68
28
5.03 3.71
40
6.10 4.72
48
7.75 5.30
65
10.70 6.74
24
10
18
26
16
20
2.35 3.20
32
3.70 4.17
44
5.03 5.17
55
5.95 6.07
75
8.67 7.73
40
20
20
30
20
22
1.90 3.46
36
2.64 4.65
48
3.95 5.65
65
3.55 7.28
80
7.65 8.25
55
30
20
32
22
40
21
36
26
28
.76
26
1.23 3.97
44
1.30 5.63
60
1.56 7.12
80
1.40 9.10
90
5.64 9.40
75
30
.72
4.48
50
.76
6.36
70
.73
8.35
90
.72 10.34
100
3.62 10.60
85
60
21
38
30
12.0
8.1
2.00
20
13.6 2.55
30
16.3 3.25
38
19.5 3.74
54
25.7 4.66
14
10
17
24
16
14.0
6.6
2.32
22
12.0 2.85
34
13.1 3.75
42
16.5 4.20
60
21.8 5.34
26
20
18
27
19
16.0
4.9
2.66
24
10.2 3.15
38
9.9
4.32
46
13.6 4.71
65
18.5 5.98
40
30
20
30
22
–
–
–
28
7.2
3.75
42
7.6
4.90
52
9.6
5.58
75
12.2 7.80
50
40
20
31
23
–
–
–
32
4.6
4.35
46
5.6
5.50
56
7.6
6.14
85
8.0
70
60
21
36
28
360° Circular Spray†
Spray
Set-up
Consists of
Fluid and
Air Cap
Combination
Spray
Dimensions
Liquid Pressure
8.90
Liquid Pressure
10
20
30
40
60
Air
Air
Air
Air
Air
gph scfm
gph scfm
gph scfm
gph scfm
gph scfm
Press.
Press.
Press.
Press.
Press.
20
4.0
2.45
34
6.6
4.09
50
7.1
6.38
60
11.0
7.6
85
14.4 11.8
22
24
2.8
2.7
38
4.4
4.8
52
6.2
6.75
65
8.3
8.63
90
12.0 13.0
2.0
2.97
42
2.8
5.5
56
4.4
7.55
70
6.1
9.78
95
9.8
14.1
26
1.5
3.3
46
1.7
6.34
60
3.2
8.41
80
3.1 12.44
100
7.8
15.4
28
1.1
3.62
48
1.3
6.85
70
1.3 11.75
90
1.4
–
–
–
15.4
†Use only with 1/8JJAU automatic air atomizing nozzles.
F28
Air Caps
• For wide angle round and flat sprays, dimensions “A”, “B” and “C” are the pattern widths at
distances from the nozzle.
Wide angle round and flat spray
air caps produce hollow cone
type, wide angle round spray
C
B
A
Wide angle round
spray pattern
6"
(15 cm)
9" (23 cm)
15" (38 cm)
D
Air Atomizing
Nozzles
12582 retainer ring and 7717-2/007 O-ring must be ordered separately from the spray set-up, but are included in
Performance Data
Spray
Set-up
No.
SUJ16
Spray
Set-up
Consists of
Fluid and
Air Cap
Combination
Fluid Cap
J2050
+
Air Cap
J67-6-20-70°
Fluid Cap
J40100
SUJ26B
+
Air Cap
J140-6-37-70°
Fluid Cap
J60100
SUJ26
+
Air Cap
J140-6-37-70°
Fluid Cap
J60100
SUJ29
+
Air Cap
J140-6-52-70°
Fluid Cap
J40100
SUJ30
+
Air Cap
J120-6-35-60°
Spray
Dimensions
Liquid Pressure
10
20
30
40
60
Air
Air
Air
Air
Air
A
gph scfm
gph scfm
gph scfm
gph scfm
Press.
Press.
Press.
Press.
Press.
(in.)
8.0
10.0
12.0
14.0
–
12.0
14.0
–
–
–
10.0
12.0
14.0
–
–
18.0
22
26
30
34
16.0
18.0
20
24
28
1.41
1.14
.79
.45
–
1.85
.55
–
–
–
6.3
3.6
2.0
–
–
9.4
7.7
6.0
4.4
3.0
3.24
2.61
2.08
1.30
.82
.36
.43
.50
.60
–
1.78
2.20
–
–
–
1.14
1.54
2.00
–
–
3.0
3.6
4.13
4.7
5.25
1.43
1.59
1.75
2.06
2.35
14.0
16.0
18.0
22
26
22
24
26
–
–
20
22
24
26
–
30
34
38
46
60
28
32
36
42
46
2.10
1.90
1.68
1.17
.55
3.30
2.20
1.20
–
–
9.0
6.9
5.1
3.3
–
13.4
11.9
10.3
7.3
2.4
4.60
3.37
2.45
1.45
1.0
.42
.50
.56
.71
.90
2.30
2.67
3.05
–
–
1.60
2.00
2.40
2.80
–
4.15
4.65
5.1
6.1
7.95
1.96
2.27
2.55
3.00
3.28
22
26
30
36
40
30
32
36
40
–
30
32
36
40
–
44
48
55
70
80
42
46
48
55
65
2.36
2.02
1.61
.91
.43
5.10
4.25
2.50
.70
–
11.2
9.3
5.4
2.3
–
15.3
13.8
11.3
6.1
3.3
5.27
4.0
3.45
2.11
1.03
.56
.69
.83
1.07
1.25
2.54
2.85
3.50
4.30
–
2.04
2.44
3.20
3.98
–
5.45
5.9
6.75
8.6
9.85
2.67
2.96
3.11
3.63
4.36
30
34
38
46
50
38
42
46
50
52
40
42
46
50
52
60
70
80
90
100
55
60
65
75
85
2.53
2.23
1.90
1.10
.69
6.40
4.70
3.06
1.40
.60
12.4
10.6
7.1
3.6
2.2
15.6
12.5
9.3
6.2
3.7
5.69
4.24
3.15
1.72
1.05
.68
.81
.94
1.26
1.45
2.84
3.42
4.05
4.84
5.34
2.54
2.92
3.72
4.51
4.91
7.05
8.25
9.45
10.7
11.9
3.30
3.68
4.06
4.82
5.58
44
48
55
65
75
54
56
60
70
75
56
58
65
75
80
80
85
90
100
–
80
85
90
100
–
2.95
2.72
2.30
1.50
.65
8.76
8.10
6.76
3.50
1.85
16.2
14.8
9.8
4.0
2.4
21.4
19.5
17.9
15.1
–
7.10
5.80
4.65
3.00
–
.81
.94
1.20
1.60
2.05
3.44
3.74
4.32
6.00
6.95
2.75
3.11
4.42
6.31
6.51
8.55
9.15
9.75
10.95
–
4.50
4.88
5.27
6.03
–
B
(in.)
C
(in.)
D
(ft.)
10
20
34
42
60
10
20
30
40
60
5-1/2
7
9
6
7-1/2 9-1/2
6-1/2
8
10
6-1/2
8
10-1/2
7-1/2
9
12
12
24
34
46
60
10
20
30
40
60
7
9-1/2 12-1/2
6
7-1/2 10
13
8
7-1/2 10
13 10-1/2
8 10-1/2 13-1/2 13-1/2
8-1/2 11 14-1/2 19-1/2
12
22
34
46
65
10
20
30
40
60
7-1/2 10
14
7
8 10-1/2 14-1/2 10-1/2
8 10-1/2 14-1/2 13-1/2
8
11
15 16-1/2
8
11 15-1/2 22-1/2
28
42
65
85
90
10
20
30
40
60
8
10
13
8 10-1/2 13-1/2
8-1/2 11 14-1/2
9 11-1/2 15
9-1/2 12-1/2 16
18
21
27
30
34
22
40
50
70
90
10
20
30
40
60
6
7-1/2
6-1/2
8
6-1/2
8
7
8-1/2
7-1/2 9-1/2
9
15
18
24
31
9
9-1/2
9-1/2
10
11
5
6
7
9
13
F29
Performance Data
Flat Spray
Spray
Set-up
No.
SUJ13A
SUJ13
SUJ14
SUJ23B
SUJ23
Spray
Set-up
Consists of
Fluid and
Air Cap
Combination
Fluid Cap
J2050
+
Air Cap
J73328
Fluid Cap
J2850
+
Air Cap
J73328
Fluid Cap
J2850
+
Air Cap
J73320
Fluid Cap
J40100
+
Air Cap
J125328
Fluid Cap
J60100
+
Air Cap
J125328
Spray
Dimensions
Liquid Pressure
10
20
30
40
60
Air
Air
Air
Air
Air
gph scfm
gph scfm
gph scfm
gph scfm
Press.
Press.
Press.
Press.
Press.
A
(in.)
B
(in.)
C
(in.)
D
(ft.)
8-1/2
10.0
1.44
.84
18.0
2.17 1.12
28
2.49 1.47
38
2.77 1.84
55
3.41 2.43
16
10
10
14
18
12.0
1.25
.96
22
1.82 1.31
32
2.19 1.64
42
2.49 2.01
65
2.83 2.85
30
20
14
19
26
10
14.0
1.09 1.08
26
1.50 1.50
36
1.89 1.82
46
2.20 2.19
75
2.26 3.26
40
30
15
21
30
10-1/2
18.0
.79
1.32
34
.93
1.87
44
1.30 2.18
60
1.25 2.81
90
1.40 3.88
50
40
18-1/2
24
34
11
22
.53
1.55
40
.57
2.16
55
.65
2.68
70
.65
3.25
100
.88
4.29
85
60
22
29
37
13
12.0
2.17
.70
20
3.35
.96
30
3.98 1.27
38
4.66 1.49
65
4.8
2.38
16
10
14
18
28
7
14.0
1.80
.82
24
2.71 1.14
34
3.41 1.45
42
4.14 1.65
70
4.21 2.62
30
20
17
24
32
8
16.0
1.45
.95
28
2.06 1.34
38
2.85 1.64
46
3.6
1.85
75
3.63 2.86
42
30
20
26
35
8-1/2
20
.77
1.2
32
1.44 1.56
46
1.72 2.07
60
1.76 2.58
85
2.48 3.35
50
40
23
30
38
9
–
–
–
36
.94
1.78
50
1.2
2.28
70
.76
3.09
95
1.57 3.85
80
60
23
30
38
10-1/2
18.0
1.04 1.05
30
1.56 1.43
42
2.06 1.75
55
2.16 2.15
75
3.20 2.66
22
10
10
13
18
6
20
.80
1.15
34
1.10 1.61
44
1.80 1.85
60
1.60 2.38
80
2.66 2.90
38
20
14
20
27
6-1/2
22
.62
1.25
36
.90
1.70
46
1.57 1.94
65
1.15 2.62
85
2.19 3.13
46
30
23
29
36
6-1/2
26
.35
1.45
40
.60
1.88
50
1.13 2.13
–
–
–
–
–
–
60
40
24
29
37
7
–
–
–
44
.35
2.07
–
–
–
–
–
–
–
80
60
25
30
38
7-1/2
–
–
16.0
2.95 1.92
28
4.45 2.66
38
5.94 3.22
46
7.50 3.66
65
9.70 4.80
20
10
6
7
8
10
18.0
2.25 2.10
30
3.87 2.84
40
5.40 3.40
50
6.45 3.97
70
8.60 5.20
32
20
9
11
13
10-1/2
20
1.72 2.30
32
3.30 3.04
42
4.86 3.55
52
5.90 4.15
75
7.50 5.60
42
30
10
13
18
11
24
1.00 2.70
36
2.28 3.40
46
3.78 3.93
56
4.87 4.50
85
5.30 6.48
54
40
12
15
18
11-1/2
60
3.84 4.90
–
75
60
13
16
19
13
–
–
–
–
–
–
–
–
–
–
–
12.0
7.0
1.15
22
11.5 1.65
34
12.4 2.20
46
13.7 2.75
65
18.3 3.56
16
10
7
9
12
11
14.0
5.4
1.35
26
8.3
2.02
38
9.8
2.57
50
10.9 3.14
75
12.6 4.47
32
20
9
12
16
11-1/2
16.0
4.2
1.57
30
6.0
2.40
42
7.8
2.95
54
8.7
3.51
80
10.6 4.95
46
30
10
13
17
12
20
2.7
1.97
34
4.3
2.78
48
5.0
3.52
60
6.4
4.06
90
6.9
5.85
56
40
12
15
19
12-1/2
–
–
–
38
3.0
3.16
52
3.7
3.90
70
3.3
5.00
100
4.5
6.76
85
60
13
16
20
14-1/2
F30
High Capacity, 1/8JJ Compact Series
• Offers an increased ability to atomize viscous fluids and allows
for greater capacities of finely atomized sprays.
• The liquid and compressed air or gas are mixed externally to
produce a completely atomized spray.
• Simple, one-piece, low-profile design permits larger air passage.
More air can be brought in to atomize the liquid stream.
• SUJE Spray Set-up Series is both compact and air efficient.
• Atomization can be controlled by varying the air pressure without
changing liquid flow rates.
• SUJE Series features lower spray velocity for improved transfer and
reduced misting and is ideal for applications where space is limited.
• Offered in three spray angles – 50°, 65° and 90°.
• When using a pressure-fed liquid system, the liquid is supplied to
the nozzle under pressure.
• Very efficient use of air results in reduced air consumption costs
and noise levels.
C
B
CP46259 retainer ring and
CP7717-2/007-VI O-ring must be
ordered separately from the spray
set-up, but are included in the
standard nozzle assembly. The 46599
adapter is used with all 1/8JJ nozzle
bodies and automatic spray guns
with extensions, but not on 1/8JJAU
spray guns without extensions.
Please contact your sales engineer.
A
Flat spray
pattern
External mix air caps
produce a flat spray pattern.
6"
(15 cm)
9" (23 cm)
15" (38 cm)
D
Performance Data
Spray
Set-up
No.
Spray
Set-up
Consists of
Fluid and
Air Cap
Combination
SUJE416-50
Fluid Cap
PFJ1650
+
Air Cap
PAJ105-50
SUJE417-50
Fluid Cap
PFJ2050
+
Air Cap
PAJ105-50
SUJE418-50
Fluid Cap
PFJ2850
+
Air Cap
PAJ105-50
SUJE420-50
Fluid Cap
PFJ40100
+
Air Cap
PAJ135-50
SUJE421-50
Fluid Cap
PFJ60100
+
Air Cap
PAJ135-50
Liquid Pressure
10
Air
Press.
10.0
20
30
40
50
10.0
20
30
40
50
10.0
20
30
40
50
10.0
20
30
40
50
30
40
50
60
70
20
gph
scfm
1.3
1.3
1.3
1.3
1.3
1.9
1.9
1.9
1.9
1.9
2.9
2.9
2.9
2.9
2.9
8.0
8.0
8.0
8.0
8.0
–
–
–
–
–
2.3
3.7
5.0
6.2
7.4
2.3
3.7
5.0
6.2
7.4
2.3
3.7
5.0
6.2
7.4
2.3
3.7
5.0
6.1
7.3
–
–
–
–
–
Air
Press.
10.0
20
30
40
50
10.0
20
30
40
50
10.0
20
30
40
50
10.0
20
30
40
50
30
40
50
60
70
30
gph
scfm
1.8
1.8
1.8
1.8
1.8
2.6
2.6
2.6
2.6
2.6
5.8
5.8
5.8
5.8
5.8
11.7
11.7
11.7
11.7
11.7
–
–
–
–
–
2.3
3.7
5.0
6.2
7.4
2.3
3.7
5.0
6.2
7.4
2.3
3.7
5.0
6.2
7.4
2.3
3.7
5.0
6.1
7.3
–
–
–
–
–
Air
Press.
10.0
20
30
40
50
10.0
20
30
40
50
10.0
20
30
40
50
10.0
20
30
40
50
30
40
50
60
70
Spray
Angle
40
gph
scfm
2.2
2.2
2.2
2.2
2.2
3.2
3.2
3.2
3.2
3.2
7.9
7.9
7.9
7.9
7.9
14.4
14.4
14.4
14.4
14.4
–
–
–
–
–
2.3
3.7
5.0
6.2
7.4
2.3
3.7
5.0
6.2
7.4
2.3
3.7
5.0
6.2
7.4
2.3
3.7
5.0
6.1
7.3
–
–
–
–
–
Air
Press.
10.0
20
30
40
50
10.0
20
30
40
50
10.0
20
30
40
50
10.0
20
30
40
50
30
40
50
60
70
gph
scfm
2.6
2.6
2.6
2.6
2.6
–
–
4.0
4.0
4.0
8.3
8.3
8.3
8.3
8.3
16.7
16.7
16.7
16.7
16.7
–
–
–
33.2
33.2
2.3
3.7
5.0
6.2
7.4
–
–
5.0
6.2
7.4
2.3
3.7
5.0
6.2
7.4
2.3
3.7
5.0
6.1
7.3
–
–
–
8.5
9.7
50°
F31
Air Atomizing
Nozzles
• Simple four-part assembly allows easy installation and maintenance.
Air Caps
High Capacity, 1/8JJ Compact Series
Performance Data
Spray
Set-up
No.
Spray
Set-up
Consists of
Fluid and
Air Cap
Combination
SUJE416-65
Fluid Cap
PFJ1650
+
Air Cap
PAJ080-65
SUJE417-65
Fluid Cap
PFJ2050
+
Air Cap
PAJ080-65
Liquid Pressure
10
Air
Press.
10.0
20
30
40
50
10.0
20
30
40
50
10.0
20
30
40
50
10.0
20
30
40
50
20
gph
scfm
1.3
1.3
1.3
1.3
1.3
1.9
1.9
1.9
1.9
1.9
2.9
2.9
2.9
2.9
2.9
8.0
8.0
8.0
8.0
8.0
1.9
3.0
4.0
5.0
5.9
1.9
3.0
4.0
5.0
5.9
1.9
3.0
4.0
5.0
5.9
2.1
3.3
4.4
5.4
6.5
Air
Press.
10.0
20
30
40
50
10.0
20
30
40
50
10.0
20
30
40
50
10.0
20
30
40
50
30
gph
scfm
1.9
3.0
4.0
5.0
5.9
1.9
3.0
4.0
5.0
5.9
1.9
3.0
4.0
5.0
5.9
2.1
3.3
4.4
5.4
6.5
Air
Press.
10.0
20
30
40
50
10.0
20
30
40
50
10.0
20
30
40
50
10.0
20
30
40
50
2.2
2.2
2.2
2.2
2.2
3.2
3.2
3.2
3.2
3.2
–
7.9
7.9
7.9
7.9
14.4
14.4
14.4
14.4
14.4
gph
scfm
1.8
1.8
1.8
1.8
1.8
2.6
2.6
2.6
2.6
2.6
5.8
5.8
5.8
5.8
5.8
11.7
11.7
11.7
11.7
11.7
Spray
Angle
40
gph
scfm
1.9
3.0
4.0
5.0
5.9
1.9
3.0
4.0
5.0
5.9
–
3.0
4.0
5.0
5.9
2.1
3.3
4.4
5.4
6.5
Air
Press.
10.0
20
30
40
50
10.0
20
30
40
50
10.0
20
30
40
50
10.0
20
30
40
50
2.6
2.6
2.6
2.6
2.6
4.0
4.0
4.0
4.0
4.0
–
–
8.3
8.3
8.3
16.7
16.7
16.7
16.7
16.7
1.9
3.0
4.0
5.0
5.9
1.9
3.0
4.0
5.0
5.9
–
–
4.0
5.0
5.9
2.1
3.3
4.4
5.4
6.5
SUJE418-65
Fluid Cap
PFJ2850
+
Air Cap
PAJ080-65
SUJE420-65
Fluid Cap
PFJ40100
+
Air Cap
PAJ125-65
30
16.0
4.4
30
–
–
30
–
–
30
–
–
SUJE421-65
Fluid Cap
PFJ60100
+
Air Cap
PAJ125-65
40
16.0
5.4
40
23.2
5.4
40
–
–
40
–
–
50
16.0
6.5
50
23.2
6.5
50
28.7
6.5
50
–
–
SUJE416-90
Fluid Cap
PFJ1650
+
Air Cap
PAJ075-90
SUJE417-90
Fluid Cap
PFJ2050
+
Air Cap
PAJ075-90
10.0
20
30
40
50
10.0
20
30
40
50
10.0
20
30
40
50
20
30
40
50
30
40
50
60
70
1.3
1.3
1.3
1.3
1.3
1.9
1.9
1.9
1.9
1.9
2.9
2.9
2.9
2.9
2.9
8.0
8.0
8.0
8.0
16.0
16.0
16.0
–
–
1.9
3.0
4.0
5.0
5.9
1.9
3.0
4.0
5.0
5.9
1.9
3.0
4.0
5.0
5.9
2.9
3.9
4.8
5.7
3.9
4.8
5.7
–
–
10.0
20
30
40
50
10.0
20
30
40
50
10.0
20
30
40
50
20
30
40
50
30
40
50
60
70
1.8
1.8
1.8
1.8
1.8
2.6
2.6
2.6
2.6
2.6
–
5.8
5.8
5.8
5.8
–
11.7
11.7
11.7
–
23.2
23.2
–
–
1.9
3.0
4.0
5.0
5.9
1.9
3.0
4.0
5.0
5.9
–
3.0
4.0
5.0
5.9
–
3.9
4.8
5.7
–
4.8
5.7
–
–
10.0
20
30
40
50
10.0
20
30
40
50
10.0
20
30
40
50
20
30
40
50
30
40
50
60
70
2.2
2.2
2.2
2.2
2.2
3.2
3.2
3.2
3.2
3.2
–
7.9
7.9
7.9
7.9
–
–
14.4
14.4
–
–
28.7
–
–
1.9
3.0
4.0
5.0
5.9
1.9
3.0
4.0
5.0
5.9
–
3.0
4.0
5.0
5.9
–
–
4.8
5.7
–
–
5.7
–
–
10.0
20
30
40
50
10.0
20
30
40
50
10.0
20
30
40
50
20
30
40
50
30
40
50
60
70
2.6
2.6
2.6
2.6
2.6
4.0
4.0
4.0
4.0
4.0
–
–
8.3
8.3
8.3
–
–
–
16.7
–
–
–
33.2
33.2
1.9
3.0
4.0
5.0
5.9
1.9
3.0
4.0
5.0
5.9
–
–
4.0
5.0
5.9
–
–
–
5.7
–
–
–
6.6
7.5
SUJE418-90
Fluid Cap
PFJ2850
+
Air Cap
PAJ075-90
SUJE420-90
Fluid Cap
PFJ40100
+
Air Cap
PAJ115-90
SUJE421-90
Fluid Cap
PFJ60100
+
Air Cap
PAJ115-90
65°
90°
F32
Air Efficient, 1/8JJ Compact Series
Air Caps
Elliptical
spray pattern
Internal mix air caps produce
an elliptical spray pattern.
A
D
Performance Data
Elliptical Spray/Air Efficient (Internal Mix)
SUJ400
SUJ401
Fluid Cap
PFJ16225
+
Air Cap
PAJ14739
Fluid Cap
PFJ20232
+
Air Cap
PAJ132-50
Spray
Dimensions
Liquid Pressure
15
20
25
30
35
40
Spray
D
Air* Liquid* Angle
Air
Air
Air
Air
Air
Air
(in.)
gph scfm
gph scfm
gph scfm
gph scfm
gph scfm
gph scfm
A
(°)
Press.
Press.
Press.
Press.
Press.
Press.
–
–
–
–
–
–
–
–
–
–
–
–
60
.13
1.1
60
.38
1.1
–
–
–
–
–
–
–
–
–
50
.17
.93
50
.60
.88
50
.88
.85
–
–
–
–
–
–
40
.18
.75
40
.71
.72
40
1.1
.68
40
1.4
.66
–
–
–
–
–
–
35
.55
.63
35
1.1
.59
35
1.4
.56
35
1.2
.53
10
10
35
24
–
–
–
30
.45
.56
30
.92
.51
30
1.3
.48
30
1.6
.46
30
1.9
.45
20
20
30
30
25
.30
.60
25
.80
.46
25
1.2
.43
25
1.5
.41
25
1.8
.39
25
2.1
.37
20
.69
.40
20
1.1
.38
20
1.4
.36
20
1.7
.34
20
1.9
.33
20
2.2
.30
15.0
.94
.33
15.0
1.5
.30
15.0
1.7
.27
15.0
1.9
.25
15.0
2.2
.23
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
50
1.1
1.4
–
–
–
–
–
–
–
–
–
40
0.7
1.2
40
1.2
1.1
40
1.8
1.0
–
–
–
–
–
–
30
1.1
.88
30
1.7
.82
30
2.1
.77
30
2.6
.71
10
10
35
26
–
–
–
25
1.0
.59
25
1.6
.70
25
2.1
.64
25
2.6
.60
25
3.0
.56
20
20
25
32
20
.85
.64
20
1.5
.56
20
2.0
.54
20
2.5
.50
20
2.8
.49
20
3.2
.48
15.0
1.3
.47
15.0
1.9
.43
15.0
2.4
.40
15.0
2.9
.36
15.0
3.2
.34
15.0
3.5
.32
10.0
1.9
.32
10.0
2.3
.30
10.0
2.7
.28
10.0
3.2
.25
10.0
3.5
.23
10.0
3.8
.22
Tabulation is based on spraying air and water at room temperature under laboratory conditions.
F33
Air Atomizing
Nozzles
Spray
Set-up
Spray
Consists of
Set-up
Fluid and
No.
Air Cap
Combination
External Mix, 1/8JJ Compact Series
Air Caps
• For round spray pattern, angle “A” is maintained throughout distance “B”. Beyond “B”,
the spray becomes turbulent and will project out to distance “D”.
• When using a siphon or gravity-fed liquid system, the liquid is supplied by either a liquid
siphon or a gravity-feed.
Round spray air caps produce
a full cone round spray pattern.
• Designed to draw liquid through the feed line into the air flow where it is atomized.
Round spray
pattern
A
B
D
12582 retainer ring and 7717-2/007 O-ring must be ordered separately from the spray set-up,
but are included in the standard nozzle assembly. Please contact your sales engineer.
Performance Data
Round Spray
Spray
Set-up
No.
Spray
Set-up
Consists of
Fluid and
Air Cap
Combination
SUJ1A
Fluid Cap J1650
+
Air Cap J64
SUJ1
Fluid Cap J2050
+
Air Cap J64
SUJ2A
Fluid Cap J2050
+
Air Cap J70
SUJ2
Fluid Cap J2850
+
Air Cap J70
SUJ3
Fluid Cap J2850
+
Air Cap J64-5
SUJ4B
Fluid Cap
J40100
+
Air Cap J120
SUJ4
Fluid Cap
J60100
+
Air Cap J120
Atomizing
Air
Liquid Capacity
(gallons per hour)*
Air
Press.
Air
Capacity
scfm
Gravity Head (in.)
18
12
6
4
10.0
20
40
60
10.0
20
40
60
10.0
20
40
60
10.0
20
40
60
10.0
20
40
60
10.0
20
40
60
20
40
60
80
.40
.59
.95
1.32
.47
.66
1.06
1.48
.81
1.20
1.94
2.70
.68
1.03
1.70
2.39
.41
.61
.99
1.36
1.30
1.97
3.12
4.28
1.90
3.00
4.10
5.20
.39
.46
.54
.59
.63
.73
.87
.98
.67
.76
.89
.98
1.19
1.37
1.48
1.57
–
–
1.68
1.91
–
–
3.20
3.47
5.80
6.50
6.80
6.80
.35
.43
.50
.54
.55
.66
.81
.92
.61
.72
.86
.96
1.05
1.27
1.41
1.47
–
1.22
1.56
1.81
–
2.57
2.96
3.24
5.15
5.95
6.35
6.40
.30
.39
.47
.49
.46
.60
.76
.88
.53
.64
.82
.94
.91
1.13
1.30
1.32
–
1.05
1.45
1.72
–
2.37
2.80
3.05
4.20
5.10
5.60
5.80
.23
.34
.41
.44
.40
.54
.71
.83
.43
.56
.76
.91
.56
.88
1.08
1.15
.59
.89
1.34
1.64
1.40
1.90
2.30
2.57
3.10
4.30
4.90
5.20
Spray
Set-up
No.
Siphon Height (in.) Spray
Set-up
8
12
24 No. 36
.18
.31
.38
.41
.32
.48
.67
.79
.37
.50
.71
.87
.47
.77
1.02
1.05
.49
.78
1.22
1.54
.97
1.50
2.02
2.32
2.65
3.70
4.20
4.50
.14
.28
.36
.39
.21
.40
.61
.73
.29
.44
.65
.81
.38
.68
.90
.91
.29
.63
1.10
1.44
.59
1.20
1.70
2.05
1.90
3.00
3.45
3.85
– SUJ1A–
.14
–
.28
.19
.31
.24
– SUJ1–
.21
.07
.43
.28
.57
.40
– SUJ2A–
.21
–
.46
.30
.68
.56
– SUJ2–
.46
–
.63
.28
.74
.52
– SUJ3–
.26
–
.70
.30
1.02
.56
– SUJ4B–
.34
–
.76
.26
1.16
.52
.60 SUJ4–
1.55
.70
2.20
1.30
2.60
1.60
Spray Dimensions
at 8" Siphon Height
Air*
Spray
Angle
A (°)
B
(in.)
D
(ft.)
10
20
40
60
18
18
18
18
11
11
12
14
6
6-1/2
7-1/2
8-1/2
10
20
40
60
18
18
18
19
12
13
15
17
7
7-1/2
8-1/2
10
10
20
40
60
18
18
19
20
12
13
15
17
8
9
11
13
10
20
40
60
21
21
21
22
15
16
18
20
10
11
13
15
10
20
40
60
18
18
18
19
12
13
15
17
8
9
11
13
10
20
40
60
17
17
18
19
18
19
21
23
10
11
13
15
20
40
60
80
17
18
18
19
18
20
21
23
12
14
16
18
F34
External Mix, 1/8JJ Compact Series
Air Caps
• For flat spray pattern, dimensions “A”, “B” and “C” are the pattern widths at distances from the nozzle.
• Total distance of spray projection from the nozzle to the maximum dispersal point is represented by “D”.
C
Flat spray air caps produce
a flat spray pattern.
B
A
Flat spray
pattern
6"
(15 cm)
9" (23 cm)
15" (38 cm)
D
Performance Data
Flat Spray
SUJF1
Fluid Cap J2850
+
Air Cap J73420
Fluid Cap J35100
SUJF2C
+
Air Cap J120432
Fluid Cap J40100
SUJF3B
+
Air Cap J122435
Fluid Cap J40100
SUJF4B
+
Air Cap J122440
Atomizing
Air
Liquid Capacity
(gallons per hour)*
Air
Capacity
scfm
18
12
6
4
8
12
24
36
10.0
.99
.35
.33
.30
.27
.25
.22
.17
.13
20
1.42
.31
.30
.29
.26
.25
.23
.19
.16
30
1.83
.18
.16
.15
.11
.09
–
–
–
20
1.86
1.01
.95
.90
.77
.72
.67
.62
.56
30
2.42
.88
.84
.81
.75
.71
.67
.63
.57
40
2.96
.76
.73
.69
.65
.61
.58
.53
.48
60
4.05
.44
.41
.37
.33
.30
.27
–
–
20
2.26
1.35
1.28
1.20
1.01
.96
.92
.78
.62
30
2.88
1.26
1.21
1.14
.92
.87
.82
.74
.59
40
3.52
.98
.92
.87
.66
.59
.52
.44
–
50
4.13
.58
.52
.44
–
–
–
–
–
20
2.10
2.01
1.90
1.71
1.47
1.40
1.32
1.17
.92
30
2.70
2.00
1.94
1.81
1.58
1.52
1.45
1.34
1.11
40
3.28
1.82
1.74
1.63
1.42
1.34
1.22
1.03
–
50
3.87
1.10
.97
.85
.69
–
–
–
–
Air
Press.
Gravity Head (in.)
Spray Dimensions
at 8" Siphon Height
Siphon Height (in.)
A
(in.)
B
(in.)
C
(in.)
D
(ft.)
10
8
10-1/2
15
7
20
8-1/2
11-1/2
15
7
30
9
12
15
6
20
30
40
60
9
9-1/2
10-1/2
11
12-1/2
13-1/2
14-1/2
15-1/2
15
16-1/2
18
19
9
9
10
9
20
7-1/2
9
10-1/2
11
30
8
10
11
11
40
8-1/2
10-1/2
12
10
20
6-1/2
8-1/2
10-1/2
11
30
7
9
11-1/2
11
40
8
10-1/2
13
11
Air*
F35
Air Atomizing
Nozzles
Spray
Set-up
No.
Spray
Set-up
Consists of
Fluid and
Air Cap
Combination
Overview/Nozzle Bodies/Nozzle Assemblies,
VAU and VMAU Series
Variable Spray Series
air atomizing nozzles
1/8VAA
Plug 29155-001-SS
Spray set-up
1/8VAAN
Shut-off needle assembly
29535-001-SS
1/8VAACO
1
1/8VAANCO
2
3
4
5
1. Cap ring 28207-101-SS
2. Air cap
3. Fluid cap
4. Nozzle body 29074-001-SS
5. Washer 29154-001-BUC
Clean-out needle assembly
29156
Shut-off/clean-out needle assembly
29534
1/8VAU
• The VAA, VAU and VMAU variable spray nozzles provide uniform
spray distribution, even when spraying viscous liquids.
• VAACO features a clean-out needle that clears the liquid orifice of
obstructions when activated manually.
• Independent control of liquid, atomizing air, and fan air pressures
is possible for fine-tuning of flow rate, drop size, spray distribution
and coverage.
• VAANCO combines the features of the VAAN and VAACO, offering
a combination shut-off/clean-out needle.
• Can be set and re-set in seconds, simplifying application changes.
• VAU offers automatic operation with a built-in shut-off/clean-out
needle.
• Independent air atomizing line can be adjusted to vary spray drop
size without affecting liquid flow rates.
• VAUPM has the same operating features as the VAU, but offers
the convenience of a mounting plate.
• Additional inlet/outlet port allows for liquid recirculation that
effectively maintains the flow of viscous liquids.
• VMAU allows for individual adjustment of the atomizing air, fan air
and liquid flows and offers modular components to accommodate
a wide range of spray applications.
• VAA offers continuous operation and consists of a body, spray
set-up and plug.
• Mounting Kit 28945-001-316SS uses clamps to mount VAA nozzles.
• VAAN features a manual shut-off needle that enables the flow of
the liquid to be stopped.
• Mounting Kit 28945-002-SS uses rods to mount VAA nozzles.
Optimization Tips
See Also
http://
• Accessories
– Pressure gauges
– Solenoid valves
– Strainers
F36
VAU and VMAU Series
VAA
VAANCO
1/8" NPT or BSPT
shut-off needle
clean-out needle
VAU
Clamp mounting kits
Rod mounting kits
1/8" NPT or BSPT
Materials
Material
Code
Material
1/8" NPT or BSPT
VAACO
Mounting Kits
VAUPM
VAAN
Air Atomizing
Nozzles
VMAU
Nozzles
303 Stainless Steel
303 Stainless Steel/Aluminum
316 Stainless Steel
Air/Fluid Caps
303 Stainless Steel
Nozzle Type
VMAU
VAA
VAAN
VAACO
VAANCO
VAU
l
l
l
l
l
l
SS
SSA
VAUPM
l
l
SS
l
l
l
l
l
l
Other materials available upon request.
Ordering Info
Nozzle Body*
Spray Set-up Only
Spray Set-up
1/8 VAA – SS
l
l
l
Inlet
Conn.
Nozzle
Body
Assembly
Type
Material
Code
Spray Set-up
+ SUV128 – SS
l
l
Spray
Set-up
No.
Material
Code
BSPT connections require the addition of a “B” prior to the
nozzle body inlet connection.
performance data charts) and material code: VF1650-SS.
performance data charts) and material code: VA67255-60-SS.
To order spray nozzle without set-up, use inlet connection,
nozzle body, and material code: 1/8VAA-SS.
Order mounting kits separately: 28945-001-316SS.
SUV128
l
Spray
Set-up
No.
–
SS
l
Material
Code
To order spray set-up only,
use spray set-up number and
material code: SUV128-SS.
F37
VMAU Series
Performance Data
VMAU
Spray
Set-up
No.
Spray
Set-up
Consists of
Fluid and
Air Cap
Combination
Liquid
Capacity*
Air Capacity*
Capacity
Press. Atomizing
Air
scfm
Fan
Air
scfm
Spray Coverage (in.) at Indicated Distance from Nozzle
Fan Air Pressure
Atom.
Water
Air
Cap. Press. Press.
Press.
gph
10.0
10.0
.58
2.0
15.0
.73
2.6
20
Fluid Cap
VMF1650
SUVM67B
+
Air Cap
VMA67255-60
.84
3.1
30
1.1
3.9
40
1.3
4.6
50
1.6
5.8
60
1.8
6.6
70
2.0
7.5
80
2.3
8.3
90
2.5
9.0
1.0
.44
3.0
.74
5.0
1.0
10.0
1.4
20
30
15.0
1.7
20
1.9
40
60
10.0
10.0
Fluid Cap
VMF2050
SUVM67A
+
Air Cap
VMA67255-60
.58
2.0
15.0
.73
2.6
20
.84
3.1
30
1.1
3.9
40
1.3
4.6
50
1.6
5.8
60
1.8
6.6
70
2.0
7.5
80
2.3
8.3
90
2.5
9.0
1.0
3.0
5.0
.65
1.1
20
1.5
30
10.0
15.0
20
2.1
2.5
40
2.9
60
0
A
B
5
C
A
B
10
C
A
B
20
C
A
B
30
C
A
B
40
C
A
B
C
3.0
2.0 3.0 4.0 5.0 6.0 7.0 7.0 9.0 10.0 7.0 9.0 11.0 3.5 4.0 6.0
–
–
–
10.0
2.5 3.5 4.5 6.0 8.0 7.0 7.0 9.0 11.0 8.0 10.0 12.0 3.5 4.0 5.5
–
–
–
20
–
–
–
–
–
–
6.0 9.0 8.0 8.0 12.0 13.0 10.0 12.0 14.0 3.5 5.5 7.0
3.0
2.0 3.0 4.5 4.0 5.0 6.0 6.0 7.0 8.0 7.0 9.0 11.0 5.0 6.5 7.0 7.0 8.0 10.0
10.0
2.0 3.0 4.0 5.0 7.0 7.0 7.0 9.0 10.0 8.0 10.0 12.0 4.5 5.0 6.0 7.0 8.0 10.0
20
2.0 3.0 4.0 6.0 7.0 8.0 8.0 10.0 12.0 9.0 12.0 14.0 6.0 7.5 9.0 7.0 8.0 10.0
3.0
2.0 3.0 4.5 3.0 4.0 5.0 5.0 6.0 7.0 6.0 8.0 10.0 5.5 6.0 7.0 7.0 9.0 11.0
10.0
2.0 3.0 4.5 4.0 4.5 6.0 6.0 7.5 10.0 7.0 9.0 11.0 5.5 6.5 8.0 7.0 9.0 12.0
20
2.0 3.0 4.0 4.5 6.0 7.0 7.0 9.0 12.0 8.0 10.0 12.0 6.0 7.0 9.0 8.0 9.0 11.0
3.0
2.5 3.5 6.0 3.5 4.5 5.0 5.0 6.0 8.0 6.0 8.0 10.0 5.0 6.5 8.0 7.0 9.0 11.0
10.0
2.0 3.0 5.0 4.0 5.0 5.0 5.0 7.0 9.0 7.0 9.0 11.0 6.0 7.5 9.0 7.0 9.0 11.0
20
2.0 3.0 4.5 4.0 5.5 6.0 6.0 8.0 10.0 8.0 9.0 11.0 6.0 7.5 10.0 8.0 10.0 12.0
3.0
2.5 3.5 6.0 3.0 4.5 4.0 4.0 5.0 6.0 5.0 7.0 9.0 5.0 6.5 10.0 7.0 9.0 11.0
10.0
2.5 3.0 5.0 3.5 4.0 4.5 4.5 5.0 7.0 7.0 9.0 11.0 6.0 7.5 11.0 8.0 10.0 12.0
20
2.0 3.0 4.5 3.5 5.0 5.0 5.0 7.0 9.0 7.0 9.0 11.0 6.0 7.5 11.5 8.0 10.0 12.0
3.0
2.0 3.0 4.0 5.0 6.0 8.0 7.0 9.0 10.0 7.0 9.0 11.0 3.5 4.0 4.5
–
–
–
10.0
2.5 3.5 4.5 6.0 8.0 9.5 7.0 9.0 11.0 8.0 10.0 12.0 4.5 5.0 6.0
–
–
–
20
–
–
–
–
3.0
2.0 3.0 4.5 4.0 5.0 6.0 6.0 7.0 8.0 7.0 9.0 11.0 5.0 7.0 8.5 7.0 8.0 10.0
10.0
2.0 3.0 4.0 5.0 7.0 9.0 7.0 9.0 10.0 8.0 10.0 12.0 6.0 7.0 8.0 7.0 8.0 10.0
20
2.0 3.0 4.0 6.0 7.0 9.0 8.0 10.0 12.0 9.0 12.0 14.0 7.0 8.0 10.0 7.0 8.0 10.0
3.0
2.0 3.0 4.5 3.0 4.0 5.0 5.0 6.0 7.0 6.0 8.0 10.0 5.5 6.5 7.0 7.0 9.0 11.0
10.0
2.0 3.0 4.5 4.0 4.5 6.0 6.0 7.5 10.0 7.0 9.0 11.0 7.0 9.0 10.0 7.0 9.0 12.0
–
–
6.0 9.0 11.0 8.0 12.0 13.0 10.0 12.0 14.0 7.0 8.5 9.5
20
2.0 3.0 4.0 4.5 6.0 8.0 7.0 9.0 12.0 8.0 10.0 12.0 8.0 10.0 12.0 8.0 9.0 11.0
3.0
2.5 3.5 6.0 3.5 4.5 7.0 5.0 6.0 8.0 6.0 8.0 10.0 6.0 8.0 9.0 7.0 9.0 11.0
10.0
2.0 3.0 5.0 4.0 5.0 7.5 5.0 7.0 9.0 7.0 9.0 11.0 6.0 8.0 9.5 7.0 9.0 11.0
20
2.0 3.0 4.5 4.0 5.5 8.0 6.0 8.0 10.0 8.0 9.0 11.0 6.0 8.5 10.5 8.0 10.0 12.0
3.0
2.5 3.5 6.0 3.0 4.5 6.0 4.0 5.0 6.0 5.0 7.0 9.0 6.5 7.5 9.0 7.0 9.0 11.0
10.0
2.5 3.0 5.0 3.5 4.0 6.5 4.5 5.0 7.0 7.0 9.0 11.0 6.5 9.0 11.0 8.0 10.0 12.0
20
2.0 3.0 4.5 3.5 5.0 7.0 5.0 7.0 9.0 7.0 9.0 11.0 6.5 9.0 12.0 8.0 10.0 12.0
F38
VMAU Series
Performance Data
VMAU
Spray
Set-up
Consists of
Fluid and
Air Cap
Combination
Liquid
Capacity*
Air Capacity*
Capacity
Press. Atomizing Fan
Air
Air
scfm
scfm
Fan Air Pressure
Atom.
Water
Air
Cap. Press. Press.
Press.
gph
10.0
SUVM67
Fluid Cap
VMF2850
+
Air Cap
VMA67255-60
10.0
15.0
20
30
40
50
60
70
80
90
.58
.73
.84
1.1
1.3
1.6
1.8
2.0
2.3
2.5
2.0
2.6
3.1
3.9
4.6
5.8
6.6
7.5
8.3
9.0
1.0
1.26
3.0
2.2
5.0
2.8
10.0
4.0
15.0
4.9
20
5.6
20
30
40
60
10.0
Fluid Cap
VMF3578
SUVM113A
+
Air Cap
VMA113289-60
10.0
15.0
20
30
40
50
60
70
80
90
1.6
2.0
2.4
3.3
3.6
4.5
5.2
5.9
6.5
7.2
3.9
4.8
5.8
7.6
9.3
11.0
12.7
14.4
15.9
17.6
1.0
2.1
3.0
3.6
5.0
4.7
10.0
6.6
15.0
8.0
20
9.4
20
30
40
60
10.0
SUVM113
Fluid Cap
VMF4078
+
Air Cap
VMA113289-60
10.0
15.0
20
30
40
50
60
70
80
90
1.6
2.0
2.4
3.3
3.6
4.5
5.2
5.9
6.5
7.2
3.9
4.8
5.8
7.6
9.3
11.0
12.7
14.4
15.9
17.6
1.0
2.9
3.0
4.9
5.0
6.4
10.0
9.0
15.0
11.0
20
12.8
20
30
40
60
3.0
10.0
20
3.0
10.0
20
3.0
10.0
20
3.0
10.0
20
3.0
10.0
20
3.0
6.0
10.0
3.0
6.0
10.0
3.0
6.0
10.0
3.0
6.0
10.0
3.0
6.0
10.0
3.0
6.0
10.0
3.0
6.0
10.0
3.0
6.0
10.0
3.0
6.0
10.0
3.0
6.0
10.0
0
5
10
20
30
40
A
B
C
A
B
C
A
B
C
A
B
C
A
B
C
A
B
C
2.0
–
–
2.5
–
–
2.5
–
–
2.5
2.0
–
2.5
2.5
2.0
–
–
–
1.5
–
–
2.0
–
–
2.0
2.5
2.0
2.0
2.5
2.5
2.0
–
–
2.0
2.0
–
2.0
1.5
–
1.5
1.5
2.0
2.0
2.0
2.0
3.0
–
–
3.0
–
–
3.0
–
–
3.5
3.0
–
3.5
3.5
3.0
–
–
–
2.0
–
–
2.5
–
–
2.5
3.5
3.0
2.5
3.0
3.0
2.5
–
–
3.0
4.0
–
2.5
2.5
–
2.5
2.5
3.0
3.0
3.0
3.0
5.0
–
–
4.5
–
–
4.5
–
–
5.0
4.5
–
5.5
5.5
4.5
–
–
–
3.0
–
–
3.5
–
–
4.0
5.56
4.0
3.0
4.5
5.0
4.0
–
–
5.0
5.0
–
4.0
3.0
–
4.5
4.0
8.0
4.0
4.0
4.0
7.0
8.5
–
6.0
6.0
7.0
5.0
5.0
–
4.0
4.5
4.5
4.0
4.5
4.0
8.0
10.0
12.0
5.0
7.0
7.0
4.0
5.0
4.5
4.0
4.0
4.5
2.0
4.0
4.0
7.0
8.0
9.0
6.5
7.0
6.5
5.0
5.0
5.5
4.0
4.5
4.5
3.5
5.0
3.5
9.0
11.0
–
7.0
8.0
9.0
6.0
7.0
–
5.0
5.5
6.0
4.5
5.0
5.5
10.5
12.0
14.0
7.0
9.0
9.0
5.0
7.0
6.0
5.0
5.0
6.0
4.0
4.5
4.5
7.5
11.5
13.0
9.0
9.0
10.5
7.0
7.5
8.0
6.0
6.0
6.5
5.0
7.5
5.0
14.0
15.0
–
9.0
11.0
12.0
8.0
10.0
–
7.5
8.0
9.0
7.0
7.5
8.0
14.0
16.0
16.5
10.0
12.0
12.0
7.0
10.0
8.0
6.0
7.5
8.5
5.0
6.0
7.5
17.0
17.0
18.0
11.0
12.0
14.0
11.0
10.0
11.0
8.0
8.0
7.5
7.0
6.0
8.0
9.0
12.0
10.0
7.5
9.0
10.0
6.0
8.0
8.0
5.0
7.0
7.0
5.0
6.0
6.0
10.0
12.0
12.0
8.0
9.0
10.5
6.0
6.5
6.5
5.5
6.0
6.5
5.0
5.5
5.5
11.0
12.0
12.0
9.0
9.5
11.0
7.0
8.0
8.0
6.5
7.0
7.0
6.0
8.0
6.0
12.0
15.0
12.0
9.0
11.0
12.0
8.0
11.0
11.0
7.0
8.0
9.0
6.0
7.0
8.0
13.0
14.0
16.5
11.0
12.0
13.5
8.0
10.0
10.0
7.5
8.0
9.0
6.5
7.0
7.5
15.0
17.0
17.0
13.0
12.0
14.0
11.0
10.0
10.5
8.5
9.0
10.0
7.5
10.5
8.0
15.0
21
16.0
11.0
15.0
17.0
9.0
15.0
14.0
10.0
11.0
13.5
8.0
9.5
10.0
17.0
18.0
22
14.0
15.0
16.5
11.0
13.0
13.0
11.0
10.0
12.0
8.0
9.5
9.5
18.0
22
23
18.0
17.0
18.5
13.5
14.5
14.0
12.0
12.5
14.5
10.0
12.0
13.0
9.0
15.0
14.0
8.0
12.0
13.0
8.0
11.0
11.0
8.0
9.0
10.0
7.0
8.0
8.0
8.0
–
–
8.5
–
–
8.0
9.0
10.0
8.0
9.0
10.0
8.0
8.0
8.5
10.0
–
–
10.0
14.0
16.0
9.0
11.0
11.5
9.0
10.0
10.0
8.0
9.0
8.5
10.0
18.0
18.0
10.0
15.0
17.0
10.0
14.0
14.0
9.0
12.0
12.0
9.0
11.0
11.0
10.0
–
–
12.0
–
–
11.0
12.0
14.0
10.5
11.5
14.0
10.0
10.0
11.0
13.5
–
–
13.0
15.0
19.0
12.0
13.5
15.0
12.0
13.0
14.0
11.0
12.5
10.5
12.0
19.0
23
13.0
19.0
20
13.0
19.0
19.0
11.0
16.0
16.0
11.0
13.0
14.0
13.0
–
–
14.0
–
–
14.0
15.5
16.0
14.0
16.0
18.5
12.0
13.0
10.0
15.0
–
–
16.5
18.5
20
17.0
16.0
20.5
16.0
17.0
19.0
14.0
15.5
16.5
–
–
15.0
5.5
11.0
14.0
5.0
9.0
12.0
5.5
9.0
10.0
5.5
6.5
9.0
–
–
–
7.0
–
–
8.0
9.0
–
8.0
8.0
10.0
7.5
10.0
10.0
–
–
–
–
–
–
8.0
10.0
12.0
8.5
10.5
11.0
9.0
9.0
9.5
–
–
19.0
6.5
12.0
17.0
5.5
11.0
16.0
6.5
10.0
12.5
6.5
9.0
11.0
–
–
–
8.5
–
–
10.5
11.0
–
10.0
11.0
13.5
9.5
12.0
12.5
–
–
–
–
–
–
11.0
12.0
15.0
11.5
12.0
13.0
11.0
12.5
13.0
–
–
23
8.0
14.0
20
6.5
12.0
19.0
8.0
11.5
16.0
7.5
11.0
15.0
–
–
–
11.0
–
–
13.0
12.0
–
13.0
14.0
18.0
14.0
15.0
18.0
–
–
–
–
–
–
13.0
15.5
18.0
15.0
16.0
17.0
15.0
18.0
16.0
–
–
–
8.0
11.0
17.0
7.0
9.0
16.0
7.0
11.0
13.0
7.0
8.0
10.0
–
–
–
5.5
–
–
7.5
–
–
7.5
8.0
8.5
7.5
9.0
9.0
–
–
–
–
–
–
–
7.5
9.5
8.5
8.5
10.0
8.0
9.5
9.5
–
–
–
9.0
12.0
20
8.0
10.0
20
9.0
13.0
18.0
9.0
10.0
14.0
–
–
–
7.0
–
–
9.0
–
–
8.5
8.5
10.5
9.5
12.0
12.0
–
–
–
–
–
–
–
10.0
12.0
11.0
11.0
12.0
10.5
11.5
12.5
–
–
–
12.0
12.0
23
10.0
12.0
22
11.0
15.0
21
11.0
12.0
16.0
–
–
–
9.0
–
–
11.0
–
–
12.0
12.0
14.5
12.0
15.0
15.0
–
–
–
–
–
–
–
14.0
17.0
14.5
15.0
19.0
14.0
16.5
16.5
F39
Air Atomizing
Nozzles
Spray
Set-up
No.
VMAU Series
Performance Data
VMAU
Spray
Set-up
No.
Spray
Set-up
Consists of
Fluid and
Air Cap
Combination
Liquid
Capacity*
Air Capacity*
Fan Air Pressure
Atom.
Water
Air
Press.
Cap.
Press.
Press. Atomizing Fan Press.
gph
Air
Air
scfm
scfm
Capacity
10.0
Fluid Cap
VMF60100
SUVM128
+
Air Cap
VMA1282100-60
10.0
15.0
20
30
40
50
60
70
80
90
1.8
2.2
2.6
3.4
4.3
5.0
5.8
6.6
7.4
8.0
4.9
5.9
7.0
9.1
11.2
13.3
15.3
17.2
19.2
21
1.0
6.6
3.0
10.8
5.0
13.8
10.0
19.8
15.0
24
20
28.2
20
30
40
60
10.0
Fluid Cap
VMF80125
SUVM152
+
Air Cap
VMA1522110-60
10.0
15.0
20
30
40
50
60
70
80
90
2.1
2.6
3.2
4.1
5.0
5.9
6.9
7.0
7.7
8.7
5.1
6.2
7.3
9.5
11.7
13.9
16.0
18.0
20.1
22
1.0
12.6
3.0
19.2
5.0
24.6
10.0
36
15.0
43.2
20
49.8
20
30
40
60
1.0
3.0
6.0
1.0
3.0
6.0
1.0
3.0
6.0
1.0
3.0
6.0
1.0
3.0
6.0
1.0
3.0
6.0
1.0
3.0
6.0
1.0
3.0
6.0
1.0
3.0
6.0
1.0
3.0
6.0
0
5
10
15
20
25
A
B
C
A
B
C
A
B
C
A
B
C
A
B
C
A
B
C
–
–
–
–
–
–
1.5
2.0
1.0
2.0
2.5
2.0
3.0
3.0
2.5
–
–
–
–
–
–
2.5
–
–
2.0
–
–
1.5
2.0
–
–
–
–
–
–
–
3.0
3.0
3.0
3.0
3.0
3.0
4.0
4.0
3.5
–
–
–
–
–
–
3.0
–
–
3.0
–
–
2.0
3.0
–
–
–
–
–
–
–
4.5
5.0
5.0
5.5
5.5
4.0
6.0
6.0
4.0
–
–
–
–
–
–
4.0
–
–
3.0
–
–
3.0
3.5
–
10.0
9.5
10.0
6.0
7.0
7.5
5.0
5.5
4.5
5.0
5.0
5.0
4.5
4.5
4.0
10.5
–
–
6.0
7.0
–
6.0
5.0
–
4.0
5.0
–
3.0
5.0
–
13.5
12.5
13.0
8.5
10.0
10.5
7.0
8.0
6.0
6.0
7.0
7.0
6.0
6.5
5.5
13.0
–
–
8.0
9.5
–
8.0
7.0
–
5.0
7.5
–
5.0
5.0
–
21
19.0
20
13.0
14.5
14.5
9.5
13.5
9.5
9.0
10.0
10.0
9.0
9.5
7.5
21
–
–
13.0
15.0
–
12.0
10.5
–
6.0
10.0
10.0
6.5
7.5
–
13.0
14.0
14.0
8.0
9.0
10.0
7.0
8.0
8.0
6.0
6.5
6.0
5.5
6.0
5.0
13.0
13.0
14.0
9.5
10.0
10.0
7.5
8.0
8.5
6.0
7.0
7.0
6.5
6.0
6.0
16.0
18.0
19.0
11.0
12.5
14.0
10.0
11.0
11.0
9.0
9.5
10.0
8.0
8.5
7.0
17.0
17.5
19.0
13.0
14.0
13.5
11.0
12.0
11.0
8.0
10.0
10.0
7.5
8.5
7.0
22
24
26
17.5
18.0
19.5
14.0
15.0
16.0
13.0
14.0
15.0
12.0
12.0
11.0
26
26
26.5
18.5
20
21
17.0
19.0
16.0
12.0
15.0
14.0
10.5
12.0
12.0
12.0
12.5
16.0
9.5
10.0
12.0
9.0
9.5
9.5
8.0
8.0
9.0
6.5
7.0
6.5
13.0
12.0
16.5
10.0
11.0
12.0
10.0
10.5
11.0
8.0
8.5
8.5
8.0
7.0
7.0
16.0
17.0
22
13.0
14.0
17.5
11.0
13.0
13.0
11.0
12.0
13.0
10.0
10.0
9.0
19.0
21
21
15.0
15.5
17.5
13.5
13.5
14.0
12.0
12.5
12.0
10.0
10.0
10.0
21
24
30
17.5
20
24
14.0
19.0
19.0
15.5
18.0
18.0
14.0
14.0
13.5
27
29
28
22
20.5
26
19.5
20
20
16.5
18.0
17.0
14.0
14.5
14.0
–
12.0
18.0
8.0
9.5
11.0
10.0
10.0
10.0
8.5
10.0
10.0
8.5
9.0
8.0
13.0
13.0
16.0
8.0
9.5
11.0
10.0
10.0
10.0
8.5
10.0
10.0
8.5
9.0
8.0
–
16.0
24.5
12.0
13.0
17.5
14.0
14.0
14.5
11.5
13.0
14.0
9.0
11.0
11.0
18.0
19.5
24
12.0
13.0
17.5
14.0
14.0
14.5
11.5
13.0
14.0
9.0
11.0
11.0
–
20
34
14.0
18.5
26
17.0
19.0
21.5
14.5
19.0
20
14.5
16.0
17.0
24
30
34
14.0
18.5
26
17.0
19.0
21.5
14.5
19.0
20
14.5
16.0
17.0
–
–
19.0
8.0
10.0
12.0
9.5
10.0
12.0
9.0
10.0
11.0
8.5
9.0
9.0
10.0
15.0
–
9.0
12.5
15.0
9.0
12.0
12.0
9.0
10.0
11.0
8.0
10.0
10.0
–
–
24
10.5
13.0
18.0
12.0
13.0
16.0
13.0
13.5
14.5
12.0
12.0
12.0
15.0
23
–
14.0
13.0
21
14.0
16.5
16.0
13.0
15.0
16.0
12.0
13.0
14.0
–
–
33
12.0
16.0
27
16.0
16.5
22
17.0
19.0
22
16.0
16.5
18.0
21.5
30
–
21
25
32
19.5
22.5
24
18.0
21
23
18.0
18.5
19.0
F40
VAU Series
Air Caps
• The dimensions “A”, “B” and “C” of the flat spray pattern are controlled by the combination of fan
air pressure and atomizing air pressure.
Fan air
Atomized liquid
• The liquid flow rate is constant and not affected by the air pressure.
Fan air
C
External mix with fan air:
flat spray pattern
Without fan air:
round spray pattern.
B
Flat spray
pattern
28207-101-SS cap ring and
29154-001-BUC must be
ordered separately from
the spray set-up, but are
included in the standard nozzle
assembly. Please contact your
sales engineer.
A
6"
(15 cm)
9" (23 cm)
15" (38 cm)
D
Performance Data
VAU
SUV67B
SUV67A
SUV67
Spray
Set-up
Consists of
Fluid and
Air Cap
Combination
Fluid Cap
VF1650
+
Air Cap
VA67255-60
Fluid Cap
VF2050
+
Air Cap
VA67255-60
Fluid Cap
VF2850
+
Air Cap
VA67255-60
Air Capacity*†
Press.
Atomizing
Air
scfm
Spray Coverage (inches) at Indicated Distance from Nozzle
Liquid Capacity*†
Fan Air
scfm
Press.
Cap.
gph
Atom.
Air
Press.
10.0
15.0
20
30
40
50
60
70
80
90
.44
.53
.62
.82
1.0
1.3
1.5
1.7
2.0
2.2
2.2
2.7
3.3
4.4
5.5
6.6
7.6
8.6
9.6
10.6
3.0
3.0
5.0
5.0
10.0
10.0
15.0
15.0
20
20
.7
.7
1.0
1.0
1.4
1.4
1.7
1.7
1.9
1.9
10.0
10.0
15.0
20
30
40
50
60
70
80
90
.44
.53
.62
.82
1.0
1.3
1.5
1.7
2.0
2.2
2.2
2.7
3.3
4.4
5.5
6.6
7.6
8.6
9.6
10.6
3.0
3.0
5.0
5.0
10.0
10.0
15.0
15.0
20
20
1.1
1.1
1.5
1.5
2.1
2.1
2.5
2.5
2.9
2.9
10.0
10.0
15.0
20
30
40
50
60
70
80
90
.44
.53
.62
.82
1.0
1.3
1.5
1.7
2.0
2.2
2.2
2.7
3.3
4.4
5.5
6.6
7.6
8.6
9.6
10.6
3.0
3.0
5.0
5.0
10.0
10.0
15.0
15.0
20
20
2.2
2.2
2.8
2.8
4.0
4.0
4.9
4.9
5.6
5.6
10.0
Fan Air Pressure
Water
Press.
3.0
10.0
20
3.0
10.0
20
3.0
10.0
20
3.0
10.0
20
3.0
10.0
20
3.0
10.0
20
3.0
10.0
20
3.0
10.0
20
3.0
10.0
20
3.0
10.0
20
3.0
10.0
20
3.0
10.0
20
30
40
60
30
40
60
30
40
60
0††
A
2.0
2.5
2.0
2.0
2.0
2.0
2.5
2.0
2.0
2.5
2.5
2.0
2.0
2.5
2.0
2.0
2.0
2.0
2.5
2.0
2.0
2.5
2.5
2.0
2.0
2.0
–
2.5
2.0
2.0
2.5
2.0
2.0
2.5
2.5
2.0
B
3.0
3.5
3.0
3.0
2.5
3.0
3.5
3.0
3.0
3.5
3.0
3.0
3.0
3.5
3.0
3.0
3.0
3.0
3.5
3.0
3.0
3.5
3.5
3.0
3.0
2.5
–
3.0
3.0
2.5
3.5
3.0
3.0
3.5
3.5
3.0
10
C
4.0
4.5
4.0
4.5
4.5
4.0
6.0
5.0
4.5
6.0
5.0
4.5
4.0
4.5
4.0
4.5
5.0
4.0
5.5
5.0
4.5
6.0
5.5
4.5
5.0
4.0
–
4.5
5.0
4.0
5.0
5.0
5.0
5.5
5.5
4.5
A
7.0
7.5
8.0
5.0
6.0
7.0
5.0
6.0
6.0
4.0
4.5
5.0
8.0
8.0
8.0
5.5
7.0
7.0
5.0
6.5
6.5
4.5
5.0
5.5
9.0
12.0
10.0
6.0
8.0
8.0
5.0
7.0
7.0
5.0
6.0
6.0
B
9.0
10.0
12.0
6.0
7.5
9.0
6.0
7.0
8.0
5.0
5.0
7.0
10.0
12.0
12.0
7.0
9.0
10.0
6.5
7.5
8.5
5.5
6.0
7.5
12.0
15.0
12.0
8.0
11.0
11.0
7.0
8.0
9.0
6.0
7.0
8.0
40
C
10.0
12.0
14.0
7.0
10.0
13.0
8.0
10.0
12.0
6.0
7.0
9.0
12.0
15.0
15.0
8.0
12.0
13.0
9.0
6.5
12.5
7.0
8.5
9.5
15.0
21
16.0
9.0
15.0
14.0
10.0
11.0
13.5
8.0
9.5
10.0
A
6.0
7.0
9.0
8.0
8.0
10.0
8.0
9.0
10.0
8.0
8.0
9.0
6.5
9.0
–
8.0
10.0
13.0
8.0
9.5
11.5
8.0
9.0
10.0
7.0
12.0
–
8.0
11.0
16.0
8.0
11.0
13.0
8.0
10.0
12.0
B
8.0
8.0
11.0
10.0
10.0
12.0
10.0
11.0
12.0
11.0
10.0
12.0
8.5
14.0
–
10.0
12.0
16.0
10.0
11.5
15.0
10.5
11.0
14.0
9.0
20
–
10.0
13.0
20
10.0
13.0
18.0
10.0
13.0
17.0
60
C
11.0
11.0
14.0
14.0
13.0
15.0
14.0
14.0
14.0
13.0
13.0
16.0
11.0
18.0
–
14.0
14.0
18.0
14.0
14.0
17.0
13.0
14.0
18.0
11.0
23
–
13.0
13.0
22
13.0
15.0
21
13.0
16.0
21
A
6.0
7.0
8.0
8.0
8.0
9.5
9.0
9.0
10.0
9.0
9.0
10.0
6.0
7.0
8.0
8.0
9.0
9.5
9.0
9.0
11.0
9.0
10.0
11.0
7.0
–
–
8.0
10.0
–
8.0
10.0
12.0
8.0
11.0
13.0
B
8.0
8.0
10.0
11.0
10.0
11.5
11.0
11.0
12.0
11.0
12.0
13.0
9.0
10.0
10.0
11.0
10.0
11.5
11.0
12.0
14.0
11.0
12.0
14.0
9.0
–
–
10.0
11.0
–
11.0
12.0
17.0
10.0
13.0
18.0
C
11.0
12.0
13.0
14.0
12.0
14.5
14.0
13.0
15.0
14.0
14.0
17.0
12.0
13.0
13.0
14.0
13.0
14.5
14.0
15.0
18.0
14.0
14.0
18.0
12.0
–
–
13.0
13.0
–
13.0
13.0
21
13.0
15.0
21
†Since the pressures of the air and liquid lines are independently controlled, any combination of these air and liquid pressures can be used. The total
air capacity is the sum of the atomizing air scfm and the fan air. For instance, for atomizing air at 10 psi and fan air at 30 psi, the total is equal to .44
scfm + 4.4 scfm for a total of 4.84 scfm.
††At 0 psi fan air pressure the spray forms a round spray pattern. Request Data Sheets 37459M-V67B, 37459M-V67A and 37459M-V67.
Spray set-ups are interchangeable, but each set-up uses a different needle size.
F41
Air Atomizing
Nozzles
Spray
Set-up
No.
VAU Series
Performance Data
VAU
Spray
Set-up
No.
SUV113A
SUV113
SUV128
SUV152
Spray
Set-up
Consists of
Fluid and
Air Cap
Combination
Fluid Cap
VF3578
+
Air Cap
VA113293-60
Fluid Cap
VF4078
+
Air Cap
VA113293-60
Fluid Cap
VF60100
+
Air Cap
VA1282125-60
Fluid Cap
VF80125
+
Air Cap
VA1522125-60
Air Capacity*†
Press.
Spray Coverage (inches) at Indicated Distance from Nozzle
Liquid Capacity*†
Atomizing
Fan Air
Air
scfm
scfm
Press.
Cap.
gph
Atom.
Air
Press.
10.0
15.0
20
30
40
50
60
70
80
90
1.6
2.0
2.4
3.2
4.0
4.7
5.5
6.3
7.0
7.8
3.5
4.4
5.4
7.2
8.9
10.6
12.3
14.0
15.5
17.2
3.0
3.0
5.0
5.0
10.0
10.0
15.0
15.0
20
20
3.6
3.6
4.7
4.7
6.6
6.6
8.0
8.0
9.4
9.4
10.0
10.0
15.0
20
30
40
50
60
70
80
90
1.6
2.0
2.4
3.2
4.0
4.7
5.5
6.3
7.0
7.8
3.5
4.4
5.4
7.2
8.9
10.6
12.3
14.0
15.5
17.2
3.0
3.0
5.0
5.0
10.0
10.0
15.0
15.0
20
20
4.9
4.9
6.4
6.4
9.0
9.0
11.0
11.0
12.8
12.8
10.0
10.0
15.0
20
30
40
50
60
70
80
90
1.6
2.0
2.4
3.1
3.9
4.7
5.4
6.2
7.0
7.8
3.9
4.9
6.0
8.1
10.2
12.3
14.3
16.3
18.2
20
3.0
3.0
5.0
5.0
10.0
10.0
15.0
15.0
20
20
10.0
10.0
13.0
13.0
18.4
18.4
23
23
26
26
10.0
10.0
15.0
20
30
40
50
60
70
80
90
1.8
2.2
2.6
3.6
4.4
5.3
6.2
7.0
7.8
8.6
3.9
4.8
5.8
7.8
9.8
11.7
13.6
15.4
17.2
18.8
3.0
3.0
5.0
5.0
10.0
10.0
15.0
15.0
20
20
18.3
18.3
24
24
33
33
41
41
47
47
10.0
Fan Air Pressure
Water
Press.
3.0
10.0
20
3.0
10.0
20
3.0
10.0
20
3.0
10.0
20
3.0
10.0
20
3.0
10.0
20
3.0
10.0
20
3.0
10.0
20
3.0
10.0
20
3.0
10.0
20
3.0
10.0
20
3.0
10.0
20
3.0
10.0
20
3.0
10.0
20
3.0
10.0
20
3.0
10.0
20
30
40
60
30
40
60
30
40
60
30
40
60
0††
A
2.5
2.0
–
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
3.0
–
–
2.5
2.5
2.0
2.5
2.5
2.5
2.5
2.5
2.5
3.0
–
–
3.0
2.5
–
3.0
2.5
2.5
3.0
3.0
3.0
3.0
–
–
3.0
–
–
3.0
3.0
–
3.0
3.0
2.5
B
3.5
3.0
–
3.0
3.5
3.5
3.0
3.5
3.5
3.5
3.5
3.5
4.0
–
–
3.5
3.5
3.0
3.5
3.5
3.5
3.5
3.5
3.5
4.0
–
–
4.0
3.5
–
4.0
3.5
3.5
4.0
4.0
3.5
4.0
–
–
4.0
–
–
4.0
3.5
–
4.0
4.0
3.0
10
C
5.0
4.5
–
5.0
5.0
5.5
5.0
5.0
5.0
5.0
4.5
4.5
6.0
–
–
6.0
5.0
5.0
6.0
5.5
5.5
6.0
5.5
5.5
5.0
–
–
5.0
5.0
–
5.5
5.0
5.0
6.0
5.0
5.0
5.0
–
–
5.0
–
–
5.5
5.0
–
6.0
6.5
5.0
A
9.0
10.0
9.0
4.0
5.0
4.0
3.5
4.0
4.0
3.0
3.0
3.0
9.0
8.0
9.0
4.0
4.5
4.5
3.5
4.0
3.5
2.5
3.0
3.0
7.0
–
–
4.0
4.0
–
3.5
4.0
3.0
3.0
3.5
3.0
8.0
–
–
5.0
5.0
–
5.0
4.5
–
4.0
4.0
3.5
B
13.0
14.0
13.0
5.0
7.0
6.0
4.5
5.0
5.5
4.0
4.0
4.5
12.0
11.0
12.0
6.0
6.0
6.0
5.0
6.0
5.0
4.0
4.0
4.0
10.0
–
–
6.0
6.0
–
5.0
5.0
5.0
4.0
4.5
4.0
11.0
–
–
6.5
7.0
–
6.0
5.5
–
6.0
6.5
4.5
40
C
17.0
16.0
17.0
7.0
9.0
9.0
6.5
6.5
8.0
6.0
6.0
7.0
18.0
15.0
15.0
8.0
8.0
9.0
7.0
8.0
8.0
7.0
6.0
6.0
13.0
–
–
8.0
8.5
–
7.0
7.0
8.0
6.0
7.0
5.5
15.0
–
–
9.0
9.0
–
9.0
7.5
–
8.0
7.5
6.0
A
–
–
18.0
11.0
13.0
13.0
9.0
10.0
11.0
8.0
8.0
10.0
–
24
21
12.0
14.0
14.0
10.0
12.0
13.0
9.0
10.0
9.0
–
21
17.0
12.0
12.0
11.0
10.0
11.0
9.0
8.0
9.0
8.0
–
21
18.0
13.0
13.0
13.0
11.0
11.0
10.0
9.0
10.0
7.0
B
–
–
24
14.0
16.0
19.0
12.0
14.0
15.0
10.0
11.0
12.0
–
29
28
15.0
18.0
18.0
13.0
16.0
17.0
11.0
13.0
13.0
–
26
22
14.0
16.0
15.0
12.0
14.0
13.0
10.0
12.0
10.0
–
27
22
18.0
17.0
17.0
15.0
15.0
14.0
12.0
13.0
12.0
60
C
–
–
29
18.0
22
24
14.0
18.0
21
13.0
14.0
16.0
–
35
–
19.0
23
27
17.0
20.0
22
14.0
16.0
17.0
–
33
30
21
22
21
17.0
20
17.0
13.0
16.0
15.0
–
35
30
23
22
22
19.0
20
20
16.0
17.0
15.0
A
–
–
–
12.0
18.0
17.0
11.0
15.0
15.0
10.0
11.0
12.0
–
–
–
12.0
17.0
18.0
12.0
15.0
16.0
10.0
13.0
12.0
–
–
22
17.0
15.0
15.0
12.0
14.0
13.0
10.0
12.0
12.0
–
–
–
–
18.0
17.0
17.0
16.0
14.0
14.0
13.0
12.0
B
–
–
–
15.0
21
22
13.0
18.0
20
12.0
15.0
17.0
–
–
–
15.0
22
23
14.0
18.0
20
12.0
16.0
17.0
–
–
27
19.0
21
18.0
17.0
18.0
18.0
13.0
16.0
16.0
–
–
–
–
25
22
24
20
19.0
17.0
17.0
16.0
C
–
–
–
18.0
26
26
18.0
22
25
17.0
18.0
22
–
–
–
19.0
25
27
18.0
22
24
17.0
20
23
–
–
34
25
28
24
21
25
24
18.0
21
21
–
–
–
–
27
29
30
29
27
21
23
21
†Since the pressures of the air and liquid lines are independently controlled, any combination of these air and liquid pressures can be used. The total
air capacity is the sum of the atomizing air scfm and the fan air. For instance, for atomizing air at 10 psi and fan air at 30 psi, the total is equal to .44
scfm + 4.4 scfm for a total of 4.84 scfm.
††At 0 psi fan air pressure the spray forms a round spray pattern. Request Data Sheets 37459M-V113A, 37459M-V113, 37459M-V128 and 37459M-V152.
Spray set-ups are interchangeable, but each set-up uses a different needle size.
F42
1/2J Series
1/2J
1/2J Series air atomizing nozzles
Plug CP1706
1/2J
Spray set-up
1/2" NPT or BSPT
Shut-off
1/2JN
1
2
3
4
5
2. Air cap
3. Fluid cap
4. Fluid cap gasket CP8491
1/2JN
1/2JCO
1/2JCO
• 1/2J air atomizing series ranges in capacity from 4.1 to 306 gph (15.5 to 1158 l/h).
• The nozzles are available with shut-off and clean-out needles.
• 1/2J body has liquid and air feeds at opposite ends of the body and is provided with a removable
plug so other needle assemblies may be added in the future.
• 1/2JN features a manual shut-off needle that enables the flow of liquid to be stopped.
1/2" NPT or BSPT
with clean-out needle
• 1/2JCO features a clean-out needle that is activated manually.
– The needle slides through the liquid orifice to clear obstructions.
– Ideal for intermittent spraying applications when liquid can dry in the orifice between uses.
Optimization Tips
See Also
http://
• Accessories
Materials
Material
Material
Code
– Pressure gauges
– Strainers
Nozzle Type
J
JN
Nozzle Body*
JCO
Nickel-plated Brass
(none)
l
l
l
303 Stainless Steel
SS
l
l
l
SSBR
l
l
l
SS
l
l
l
Spray Set-ups
303 Stainless Steel
– Solenoid valves
Ordering Info
Nozzle Bodies
Nickel-plated Brass Air Cap and
303 Stainless Steel Fluid Cap
1/2
JN
Inlet
Conn.
Nozzle
Body
Assembly
Type
l
l
Spray Set-up Only
Spray Set-up
– SS + SU77 –
l
l
Material
Code
Spray
Set-up
No.
SS
l
Material
Code
BSPT connections require the addition of a “B” prior
to the nozzle body inlet connection.
performance data charts) and material code: 422-6-73-70°.
Spray Set-up
SU77 –
l
Spray
Set-up
No.
SS
l
Material
Code
and material code:
SU77-SS.
F43
Air Atomizing
Nozzles
1/2" NPT or BSPT
with shut-off needle
Clean-out needle
assembly 11829
Nozzle Bodies/Nozzle Assemblies, 1/2J Series
Optimization Tips
• JBC features the center lines of the air and liquid inlet entering
in the back of the nozzle and parallel to the spray projection axis.
• 1/2JBCJ features a steam jacket around the nozzle body
for spraying liquids that are too viscous to spray at room
temperature.
See Also
• 2J is a dual spray assembly with opposing spray set-ups
perpendicular to opposing air and liquid inlets.
• Accessories
• Thick wall adapters replace retainer rings on nozzle assemblies
and fit into threaded wall openings holding the nozzle securely
in place.
http://
– Pressure gauges
– Solenoid valves
– Strainers
• For JBC, request Data Sheets 4921, 6885 and 6185
• For 1/2JBCJ, request Data Sheets 4610 and 6331
• For 2J, request Data Sheets 5356 and 6530
• For thick wall adapters, request Data Sheets 3378,
7003 and 7323
Back Connect
inlet connection
Steam Jacket
Twin Spray
steam inlet/outlet connection
air and liquid inlet connection
inlet connection
Thick Walls
Please refer to data sheets
1/2JBC air atomizing nozzle
1/2JBC air atomizing nozzle used to spray
seasoned cooking oil onto corn snacks.
F44
1/2J Series
Air Caps
• For wide angle round, round, 360° circular and flat sprays, dimensions “A”, “B” and “C” are the
pattern widths at distances from the nozzle.
Wide angle round, round, flat
and 360° circular spray air
caps produce wide angle round
hollow cone spray, round hollow
cone spray, flat spray and 360°
circular spray patterns.
Fluid cap
C
B
A
Air cap
9"
(23 cm)
18" (46 cm)
27" (69 cm)
D
8491
gasket
1705 retainer ring
Air Atomizing
Nozzles
8491 gasket must be ordered separately from the spray set-up, but is included in the
standard nozzle assembly. Please contact your sales engineer.
Performance Data
Flat Spray
Spray
Set-up
Spray
Consists of Spray
Set-up
Fluid and Pattern
No.
Air Cap
Combination
SU75
SU85
Fluid Cap
250375
+
Air Cap
4533102
Fluid Cap
251376
+
Air Cap
4693102
Flat
Flat
Spray
Dimensions
Liquid Pressure
5
15
25
35
55
Air
Air
Air
Air
Air
A
B
C
D
gph scfm
gph scfm
gph scfm
gph scfm
Press.
Press.
Press.
Press.
Press.
(in.) (in.) (in.) (ft.)
–
–
–
28
39
22.4
44
44.1 31.5
58
53
40
–
–
–
–
–
–
30
31.8
24
46
37.2 33.5
60
45.6
42
–
–
–
–
–
–
32
24.6 25.9
48
31.2 35.1
63
38
44
–
–
–
–
–
–
34
19.8 27.5
50
27
36.9
65
31
47
–
–
–
23
10.0
35.4 11.1
18.0
103 15.4
26
155 17.7
36
180
54
222
29.1
12.0
26.4 13.4
20
81.6 17.6
28
135
38
162 25.4
56
198
31.2
20
–
–
–
22
63.6 19.8
30
115 22.5
40
147 27.8
58
186
34
–
–
–
24
49.3 22.6
32
100 25.1
42
131 30.2
60
180
36.3
–
–
–
–
–
–
34
84
27.5
44
116 32.6
62
166
38.9
–
–
–
–
–
–
36
69.5
30
46
101 35.1
64
154
41.6
–
–
–
–
–
–
38
56.4 32.6
48
81.5 37.6
66
142
44.1
–
–
–
–
–
–
40
45.7 35.3
50
75.6 40.2
68
130
46.6
–
–
–
–
–
–
–
–
–
52
62.4 42.7
70
119
49.3
–
–
–
–
–
–
–
–
–
–
–
–
72
108
51.6
–
–
–
–
–
–
–
–
–
–
–
–
74
97.4 54.2
–
–
–
–
–
–
–
–
–
–
–
–
76
87.5 57.1
20
10
17
28
35
18
30
15
18
29
36
19
10
5
20
34
47
13
20
15
34
62
83
15
32
25
34
62
82
17
44
35
36
66
85
19
64
55
36
67
89
21
F45
1/2J Series
Performance Data
Wide Angle Round and Round Spray
Spray
Set-up
Spray
Consists of Spray
Set-up
Fluid and Pattern
No.
Air Cap
Combination
SU77
SU78
SU79
SU89
SU72
SU82
Fluid Cap
250375
Wide
+
Angle
Air Cap
Round
422-6-73-70°
Fluid Cap
250375
Wide
+
Angle
Air Cap
Round
422-6-94-70°
Fluid Cap
250375
+
Air Cap
469-6-12570°
Fluid Cap
251376
+
Air Cap
469-6-13070°
Fluid Cap
250375
+
Air Cap
4221250
Fluid Cap
251376
+
Air Cap
4691312
Wide
Angle
Round
Wide
Angle
Round
Round
Round
Spray
Dimensions
Liquid Pressure
5
15
25
35
55
Air
Air
Air
Air
Air
gph scfm
gph scfm
gph scfm
gph scfm
Press.
Press.
Press.
Press.
Press.
–
–
–
–
–
–
28
–
–
–
–
–
–
30
33
A
(in.)
B
(in.)
C
(in.)
D
(ft.)
8.4
40
28.8 11.3
58
66
12.2
30
25
13-1/2
19
26-1/2 22
19.8 10.8
42
15.6 13.9
60
42
15.0
40
35
13-1/2
19
26-1/2 24
14
19-1/2
–
–
–
–
–
–
–
–
–
–
–
–
62
25.2 18.2
60
55
8.0
10.0
12.0
–
–
10.0
12.0
14.0
–
–
10.0
12.0
–
–
–
–
–
–
–
–
–
–
18.0
20
22
24
–
–
10.0
12.0
–
–
–
–
–
–
–
–
–
–
27
15.0
8.4
–
–
34.2
21.6
12.0
–
–
35.4
26.4
–
–
–
–
–
–
–
–
–
–
9.0
6.7
5.4
4.1
–
–
35.4
26.4
–
–
–
–
–
–
–
–
–
–
6.5
8.2
9.8
–
–
11.4
13.0
14.7
–
–
11.1
13.4
–
–
–
–
–
–
–
–
–
–
12.4
13.7
14.7
15.7
–
–
11.1
13.4
–
–
–
–
–
–
–
–
–
–
18.0
20
22
24
–
26
28
30
32
34
18.0
20
22
24
–
–
–
–
–
–
–
–
28
32
36
38
40
42
18.0
20
22
24
–
–
–
–
–
–
–
–
42
29.4
20.2
14.4
–
46.2
37.2
28.4
21.6
16.2
103
81.6
63.6
49.3
–
–
–
–
–
–
–
–
31.7
22.5
15.9
13.2
11.1
9.2
103
81.6
63.6
49.3
–
–
–
–
–
–
–
–
7.0
8.8
10.5
12.2
–
20.2
22
23.7
25.3
27
15.4
17.6
19.8
22.6
–
–
–
–
–
–
–
–
14.9
17.0
19.3
20.4
21.5
22.6
15.4
17.6
19.8
22.6
–
–
–
–
–
–
–
–
32
34
36
38
40
40
42
44
46
48
26
28
30
32
34
36
38
40
–
–
–
–
38
44
50
54
58
60
26
28
30
32
34
36
38
40
–
–
–
–
47
36
25.2
18.6
13.8
62.6
52.8
43.8
33.6
25.2
155
135
115
100
84
69.5
56.4
45.7
–
–
–
–
58
37.7
24.7
19.5
16.0
14.5
155
135
115
100
84
69.5
56.4
45.7
–
–
–
–
11.0
12.8
14.7
16.6
18.6
27.5
29.6
31.6
33.6
35.6
17.7
20
22.5
25.1
27.5
30
32.6
35.3
–
–
–
–
17.3
20.8
24.8
27.5
30.2
31.8
17.7
20
22.5
25.1
27.5
30
32.6
35.3
–
–
–
–
46
48
50
52
54
54
56
58
60
62
36
38
40
42
44
46
48
50
52
–
–
–
48
54
60
66
72
78
36
38
40
42
44
46
48
50
52
–
–
–
42.6
32.4
25.8
19.8
15.6
75.6
57
46.8
39
33
180
162
147
131
116
101
81.5
75.6
62.4
–
–
–
80
55.2
40
30
23.3
18.3
180
162
147
131
116
101
81.5
75.6
62.4
–
–
–
18.1
20.2
22.2
24
25.8
32.6
34.3
35.8
37.3
38.8
23
25.4
27.8
30.2
32.6
35.1
37.6
40.2
42.7
–
–
–
19.3
23.6
27.5
32.1
37
42.2
23
25.4
27.8
30.2
32.6
35.1
37.6
40.2
42.7
–
–
–
70
75
80
–
–
75
80
85
–
–
54
56
58
60
62
64
66
68
70
72
74
76
–
–
–
–
–
–
54
56
58
60
62
64
66
68
70
72
74
76
81
33
22.2
–
–
127
108
98
–
–
222
198
186
180
166
154
142
130
119
108
97.4
87.5
–
–
–
–
–
–
222
198
186
180
166
154
142
130
119
108
97.4
87.5
10
20
36
50
75
5
15
25
35
55
13 18-1/2 25-1/2 20
13-1/2 19 26-1/2 26
13 18-1/2 25-1/2 21
13-1/2 19 26-1/2 24
14
19
27
27
12
30
46
60
80
5
15
25
35
55
14
13-1/2
13
14
14
10
5
13
25
36
11
20
15
13
26
36
16
32
25
11
22
32
20
44
35
11
21
29
22
64
55
11
22
31
25
29.5
34.5
39.6
–
–
39
42.4
45.6
–
–
29.1
31.2
34
36.3
38.9
41.6
44.1
46.6
49.3
51.6
54.2
57.1
–
–
–
–
–
–
29.1
31.2
34
36.3
38.9
41.6
44.1
46.6
49.3
51.6
54.2
57.1
27
28
19-1/2 27
26
19 26-1/2 24
18-1/2 26
23
19-1/2 27
28
19-1/2 28
30
20
5
3-1/2 6-1/2
10
22
36
15
3-1/2 6-1/2
10
24
50
25
3-1/2 6-1/2
10
27
60
35
3-1/2 6-1/2
10
30
10
5
4
7
9
23
20
15
6
10
13
21
32
25
5
8
10
37
44
35
4
7
10
41
64
55
4
7
10
47
F46
1/2J Series
Air Caps
• The dimensions “A”, “B” and “C” are the pattern widths at distances from the nozzle.
• The total distance of spray projection from the nozzle to the maximum dispersal point is represented
by “D”.
• SUE75 and SU380C are pressure set-ups using pressurized liquids.
Flat spray air caps produce
a flat spray pattern.
• In SU380C, the air and liquid mix internally, while in SUE75, they mix externally.
• SU70 is a siphon set-up with the air and siphoned liquid mixing externally.
Fluid cap
Air cap
C
B
A
Flat spray
pattern
9"
(23 cm)
18" (46 cm)
27" (69 cm)
D
8491
gasket
1705 retainer ring
Air Atomizing
Nozzles
Performance Data
Spray
Set-up
Spray
Consists of
Set-up
Fluid and
No.
Air Cap
Combination
SUE75
Fluid Cap
250375
+
Air Cap
14356
Spray
Dimensions
Liquid Pressure
3
5
7
10
15
Air
Air
Air
Air
Air
A
gph scfm
gph scfm
gph scfm
gph scfm
Press.
Press.
Press.
Press.
Press.
(in.)
30
138
31
40
180
35
138
34
45
40
138
38
45
138 41.5
45
210 41.5
55
252
180 41.5
50
210
45
60
50
180
45
55
210
48
55
180
48
60
180 51.5
–
–
–
60
–
–
–
–
–
38
–
48
80
306
65
252 51.5
85
306
69
70
252
58
90
306
72
210 51.5
75
252
62
95
306
75
65
210
55
80
252
65
100
306
78
70
210
58
85
252
69
–
–
–
35
3
50
5
B
(in.)
C
(in.)
D
(ft.)
8-1/2 14-1/2 20-1/2 19
9
16-1/2 21-1/2 22
55
7
9-1/2 17-1/2
23
23
70
10
9-1/2
18
24
25
90
15
10
19
26
29
F47
1/2J Series
Performance Data
360° Circular Spray
Spray
Set-up
No.
SU380C
Spray
Set-up
Consists of
Fluid and
Air Cap
Combination
Fluid Cap
251376
+
Air Cap
469-6-130160HC
Liquid Pressure
10
20
30
40
60
Air
Air
Air
Air
Air
gph scfm
gph scfm
gph scfm
gph scfm
gph scfm
Press.
Press.
Press.
Press.
Press.
14.0
56.4
12.2
24
104
16.0
36
116
22.4
48
122
27.8
72
128
40.2
16.0
38.4
14.8
26
85.8
18.6
38
98.4
24.8
50
110
29.8
74
116
42.3
18.0
25.8
16.8
28
72.6
20.3
40
85.2
26.5
52
98.4
31.5
76
108
44.3
20
15.6
19.0
30
54.6
22.7
42
73.2
28.9
54
85.8
33.8
78
96.6 46.3
–
–
–
32
42
24.8
44
72
30.9
56
74.4
36
80
85.8 48.3
–
–
–
34
30.6
26.8
46
49.8
32.9
58
66
38.3
82
78.6 50.5
–
–
–
36
24.6
29.3
48
38.4
35
60
55.2
40.1
84
67.8 52.5
–
–
–
38
7.2
31.8
50
30
37.8
62
44.4
42
86
61.2 54.8
–
–
–
–
–
–
–
–
–
64
37.2
44.5
90
48
59
–
–
–
–
–
–
–
–
–
66
20.4
45.8
–
–
–
Odor control at a compost facility using air atomizing nozzles.
F48
External Mix, 1/2J Series
Air Caps
Air cap
C
B
Fluid cap
A
Round spray
pattern
9"
(23 cm)
18" (46 cm)
27" (69 cm)
Round spray siphon air caps
produce a round spray pattern.
D
8491
gasket
1705
retainer ring
1705 retainer ring and 8491 gasket must be ordered separately from the spray set-up,
but are included in the standard nozzle assembly. Please contact your sales engineer.
Refer to page F3 for Siphon/Gravity-Fed Liquid Spray Set-ups diagram.
Performance Data
Round Spray Siphon Set-ups
SU70
Fluid Cap
250375
+
Air Cap
437
Atomizing
Air
Liquid Capacity
(gallons per hour)*
Air
Press.
Air
Capacity
scfm
Gravity Head (in.)
18
12
6
4
10.0
12.7
–
–
–
20
18.5
–
–
–
30
24
–
–
40
29.2
–
50
34.8
60
40.1
Spray Dimensions
at 8" Siphon Height
Siphon Height (in.)
8
12
24
10.7
–
–
–
22.8
13.9
–
–
–
32.4
24.8
13.8
–
67.6
58.8
38.8
31.2
22.7
–
79.8
70.5
62.8
43
35.2
27.6
–
81.9
72.1
63.5
45.4
38.3
30.5
9.5
70
46.1
83.2
74.5
66.0
48
41.4
33.9
13.8
80
51.0
84.6
76.2
67.6
49.8
43.2
36
16.5
Air*
A
(in.)
B
(in.)
C
(in.)
D
(ft.)
20
3
6
8-1/2
20
30
3
6
8-1/2
22
40
3
6
8-1/2
24
50
3
6
8-1/2
26
60
3
6
8-1/2
29
70
3
6
8-1/2
32
80
3
6
8-1/2
35
F49
Air Atomizing
Nozzles
Spray
Set-up
No.
Spray
Set-up
Consists of
Fluid and
Air Cap
Combination
1J Series
1J Series air atomizing
Spray set-up
1J
1
3
Shut-off
4
2. Air cap
3. Fluid cap
1JN
1J
2
Plug CP1706
1JN
• Range in capacity from 24 to 1740 gph (91 to 6586 l/h).
• Available with a shut-off needle.
• 1J features liquid and air feeds at opposite ends of the body and
are provided with a removable plug so other needle assemblies
may be added in the future.
1" NPT or BSPT (F)
1" NPT or BSPT (F)
with shut-off needle
• 1JN features a manual shut-off needle that enables the flow of
liquid to be stopped.
Optimization Tips
See Also
• Accessories
Materials
Material
http://
– Pressure gauges
– Solenoid valves
– Strainers
Ordering Info
Material
Code
Nozzle Type
J
Nozzle Body*
JN
Nozzle Bodies
1
JN
Inlet
Conn.
Nozzle
Body
Assembly
Type
l
l
– SS
l
Spray Set-up Only
Spray Set-up
+
SU159 –
l
Spray Set-up
SS
l
Nickel-plated Brass
(none)
l
l
303 Stainless Steel
SS
l
l
SSBR
l
l
SS
l
l
Spray Set-ups
303 Stainless Steel
Material
Code
Spray
Set-up
No.
Material
Code
SU159 –
l
Spray
Set-up
No.
SS
l
Material
Code
number and material
code: SU159-SS.
performance data charts) and material code: 1109-6-224-70-SS.
To order spray nozzle without set-up, use inlet connection,
nozzle body and material code: 1JN-SS.
F50
1J Series
Air Caps
• For wide angle round, round and flat sprays, dimensions “A”, “B” and “C” are the pattern widths
at distances from the nozzle.
Wide angle round, round,
and flat spray air caps
produce hollow cone, wide
angle round spray, round
Fluid cap
C
Air cap
B
A
12"
(30 cm)
30" (76 cm)
48" (122 cm)
D
5713 retainer ring
Air Atomizing
Nozzles
5713 retainer ring must be ordered separately from the spray set-up, but is included in
Performance Data
Wide Angle Round
Spray
Set-up
Spray
Consists of Spray
Set-up
Fluid and Pattern
No.
Air Cap
Combination
Fluid Cap
4371000
+
SU159
Air Cap
1109-6-22470°
Wide
Angle
Round
Liquid Capacity (gallons per minute)* and Air Capacity (standard cubic feet per minute)*
Spray
Dimensions
Liquid Pressure
10
20
30
40
60
Air
Air
Air
Air
Air
A
B
C
D
gpm scfm
gpm scfm
gpm scfm
gpm scfm
gpm scfm Air* Liquid*
Press.
Press.
Press.
Press.
Press.
(in.) (in.) (in.) (ft.)
12.0
3.2
43
22
5.1
52
32
6.5
64
42
7.7
79
60
10.6
99
14.0
2.4
51
24
4.1
62
34
5.5
75
44
6.7
90
62
9.5
108
16.0
1.7
61
26
3.3
72
36
4.5
86
46
5.7
100
64
8.4
118
–
–
–
28
2.6
85
38
3.6
96
48
4.9
110
66
7.5
130
–
–
–
30
2.0
94
40
3.1
106
50
4.2
120
68
6.8
142
–
–
–
32
1.6
104
42
2.6
116
52
3.6
132
70
6.1
152
–
–
–
–
–
–
44
2.2
128
54
3.1
140
72
5.5
166
–
–
–
–
–
–
46
1.8
136
56
2.7
150
74
5.0
178
–
–
–
–
–
–
–
–
–
58
2.3
164
76
4.5
190
14
26
32
38
46
50
60
60
86
10
20
20
30
30
40
40
60
60
19
21
17
21
16
20
17
22
15
37
40
33
41
33
44
40
47
31
55
59
47
58
49
62
54
67
41
14
19
25
29
37
37
46
42
61
F51
1J Series
Performance Data
Round and Flat Spray
Spray
Set-up
Spray
Consists of Spray
Set-up
Fluid and Pattern
No.
Air Cap
Combination
SU152
Fluid Cap
4371000
+
Air Cap
11091547
Round
SU172
SU155
Fluid Cap
4371000
+
Air Cap
11093187
Round
Flat
Spray
Dimensions
Liquid Pressure
10
20
30
40
60
A
B
C
D
Air
Air
Air
Air
Air
gpm scfm
gpm scfm
gpm scfm
gpm scfm
(in.) (in.) (in.) (ft.)
Press.
Press.
Press.
Press.
Press.
12.0
3.2
43
22
5.1
52
32
6.5
64
42
7.7
79
60
10.6
99
14.0
2.4
51
24
4.1
62
34
5.5
75
44
6.7
90
62
9.5
108
16.0
1.7
61
26
3.3
72
36
4.5
86
46
5.7
100
64
8.4
118
–
–
–
28
2.6
85
38
3.6
96
48
4.9
110
66
7.5
130
–
–
–
30
2.0
94
40
3.1
106
50
4.2
120
68
6.8
142
–
–
–
32
1.6
104
42
2.6
116
52
3.6
132
70
6.1
152
–
–
–
–
–
–
44
2.2
128
54
3.1
140
72
5.5
166
–
–
–
–
–
–
46
1.8
136
56
2.7
150
74
5.0
178
–
–
–
–
–
Fluid Cap
6251000
+
Air Cap
11251625
–
–
–
58
2.3
164
76
4.5
190
12.0
5.92 48.5
20
–
11.0 42.5
30
13.2
55
40
15.1
66
60
18.3
79
14.0
4.40
82
22
9.1
60
32
11.7
69
42
13.8
78
65
15.8 107
16.0
3.45 128
24
7.8
80
34
10.4
85
44
12.6
93
70
13.5 138
18.0
2.75 187
26
6.72 110
36
9.4
102
46
11.6 109
–
–
–
–
–
–
28
5.95 143
38
8.45 125
48
10.7 125
–
–
–
–
–
–
30
5.25 183
40
7.75 150
50
9.7
145
–
–
–
12.0
3.2
43
22
5.1
52
32
6.5
64
42
7.7
79
60
10.6
99
14.0
2.4
51
24
4.1
62
34
5.5
75
44
6.7
90
62
9.5
108
16.0
1.7
61
26
3.3
72
36
4.5
86
46
5.7
100
64
8.4
118
–
–
–
28
2.6
85
38
3.6
96
48
4.9
110
66
7.5
130
–
–
–
30
2.0
94
40
3.1
106
50
4.2
120
68
6.8
142
–
–
–
32
1.6
104
42
2.6
116
52
3.6
132
70
6.1
152
–
–
–
–
–
–
44
2.2
128
54
3.1
140
72
5.5
166
–
–
–
–
–
–
46
1.8
136
56
2.7
150
74
5.0
178
–
–
–
–
–
–
–
–
–
58
2.3
164
76
4.5
190
14
26
32
38
46
50
60
60
86
10
20
20
30
30
40
40
60
60
4
4
4
4
4
4
4
5
4
8
8
9
9
10
9
10
9
10
12
13
13
13
14
14
15
13
15
30
36
41
45
53
54
63
59
83
14
10
6
11
13
25
24
20
6
11
14
30
36
30
6
10
14
35
46
40
6
10
14
42
65
60
6
11
15
50
14
26
32
38
46
50
60
60
86
10
20
20
30
30
40
40
60
60
29
32
23
34
27
37
29
49
25
60
64
50
72
52
72
59
88
63
84
92
70
96
70
104
88
126
92
21
23
26
27
30
30
33
31
39
F52
Pressure Spray and Siphon/Gravity-Fed
Spray Set-ups, External Mix, 1J Series
Air Caps
• For flat spray, dimensions “A”, “B” and “C” are the pattern widths at distances from the nozzle.
– The total distance of spray projection from the nozzle to the maximum dispersal point is
– When using a pressure-fed liquid system, the liquid is supplied to the nozzle under pressure.
– The liquid and compressed air or gas are mixed externally to produce a completely atomized spray.
• For round spray, dimensions “A”, “B” and “C” are the pattern widths at distances from the nozzle.
– The total distance of spray projection from the nozzle to the maximum dispersal point is
– When using a siphon or gravity-fed liquid system, the liquid is supplied by either a liquid siphon or
a gravity-feed.
– Designed to draw liquid through the feed line into the air flow where it is atomized.
Flat spray and round
spray air caps produce a
flat spray pattern and the
siphon air caps produce a
round spray pattern.
C
Fluid cap
Air cap
B
A
Flat spray
pattern
Air Atomizing
Nozzles
12"
(30 cm)
30" (76 cm)
48" (122 cm)
12415 retainer ring
D
12415 retainer ring must be ordered separately from the spray set-up, but is included
in the standard nozzle assembly. Please contact your sales engineer.
Performance Data
Spray
Set-up
No.
SUE175B
Spray
Set-up
Consists of Spray
Fluid and Pattern
Air Cap
Combination
Fluid Cap
625780
+
Air Cap
12116
Flat
Spray
Dimensions
Liquid Pressure
3
5
7
10
20
25
30
40
50
60
13.0
13.0
13.0
13.0
13.0
13.0
87
101
115
140
166
191
25
30
40
50
60
70
17.0
17.0
17.0
17.0
17.0
17.0
101
115
140
166
191
216
30
40
50
60
70
80
20
20
20
20
20
20
115
140
166
191
216
242
40
50
60
70
80
90
Siphon Set-ups Round Spray
Spray
Set-up
No.
SU170
Spray
Set-up
Consists of
Fluid and
Air Cap
Combination
Fluid Cap
6251000
+
Air Cap
1125
15
Air
Air
Air
Air
Air
A
B
C
D
gpm scfm
gpm scfm
gpm scfm
gpm scfm
Press.
Press.
Press.
Press.
Press.
(in.) (in.) (in.) (ft.)
23
23
23
23
23
23
140
166
191
216
242
268
50
60
70
80
90
–
29
29
29
29
29
–
166
191
216
242
268
–
30
40
50
60
70
3
5
7
10
15
20
22
23
22
22
36
37
39
38
39
47
48
51
49
50
25
28
30
32
35
Atomizing
Air
Liquid Capacity
(gallons per minute)*
Spray Dimensions
at 8" Siphon Height
Air
Press.
Air
Capacity
scfm
18
12
6
4
8
12
18
20
25
30
40
60
80
100
105
120
135
165
225
285
345
–
5.2
5.3
5.4
5.5
5.6
5.7
–
4.5
4.6
4.7
4.9
5.0
5.1
3.4
3.6
3.8
3.9
4.2
4.4
4.5
1.9
2.2
2.4
2.6
2.9
3.0
3.1
–
–
1.4
1.8
2.2
2.3
2.4
–
–
–
1.1
1.5
1.6
1.7
–
–
–
–
.40
.50
.60
Gravity Head (in.)
Siphon Height (in.)
Air*
A
(in.)
B
(in.)
C
(in.)
D
(ft.)
30
5
10
15
29
40
5
10
15
35
60
5
10
15
44
80
5
10
15
54
100
5
10
15
64
Refer to page F3 for Siphon/Gravity-Fed Liquid Set-ups.
F53
Fogger Spray Nozzles,
Special Purpose
23412
QJ25655
• 23412 produces high quality, cost-efficient dry fog.
– Drops average fifteen microns in size and less.
– Drop size is adjustable to meet specific industrial needs by
changing the ratio of compressed air to water.
– Maintenance time is reduced because the built-in check
valve, spray tip, and internal strainer are quickly serviced
without tools.
threaded type
– Can use PVC pipe and low-pressure air tubing.
Split-eyelet type to clamp on
1/2", 3/4", 1" pipe size
– Tip has a relatively large clog-reducing orifice.
• QJ25655 provides fast installation of the nozzle onto the liquid
supply pipe – no additional pipe fittings are required.
– Pipe cutting, threading and brazing are eliminated.
– Features a chemical-resistant, tight-fitting Buna-N seal to
ensure leak-free performance.
Ordering Info
Specifications
Complete Nozzle
Assembly
Complete Nozzle
Assembly
23412 – 1/4 – 20
QJ25655 – 3/4 – 20
l
l
l
Nozzle
Body
Inlet
Conn.
Fluid
Orifice
Dia.
l
l
l
Nozzle
Body
Pipe
Size
Fluid
Orifice
Dia.
Nozzle
Inlet
(in.)
AirJet
Fogger
Type
1/4
23412
Fluid
Orifice
No.
Orifice
Dia.
Nom.
(in.)
16.0
.016
20
.020
26
.026
Fluid
Orifice
No.
Orifice
Dia.
Nom.
(in.)
16.0
.016
20
.020
26
.026
BSPT connections require the addition of a “B” prior to the nozzle body
inlet connection.
To Clamp On
Pipe
Size
(in.)
AirJet
Fogger
Type
1/2
3/4
QJ25655
1
Humidification to reduce static charge in paint manufacturing plants.
F54
Special Purpose
Performance Data
23412, QJ25655
Fluid Orifice No. 16 (.016" Dia.)
Water
Pressure
20†
30
40
50
60
70
80
90
100
Water
Pressure
Air Pressure*
10
20
30
40
50
60
70
80
10
20
30
40
50
60
70
80
1.1
–
–
–
–
–
–
3.1
1.7
–
–
–
–
–
–
1.5
2.5
–
–
–
–
–
–
1.4
2.8
–
–
–
–
–
–
1.7
1.6
1.2
–
–
–
–
–
3.6
2.1
1.7
–
–
–
–
–
1.4
2.4
3.4
–
–
–
–
–
1.3
2.5
3.6
–
–
–
–
–
2.0
1.6
1.5
1.4
–
–
–
–
4.3
3.1
2.2
–
–
–
–
–
1.4
2.4
3.3
4.2
–
–
–
–
1.2
2.3
3.4
–
–
–
–
–
2.1
1.9
1.7
1.5
1.3
–
–
–
4.9
3.7
3.1
2.3
–
–
–
–
1.4
2.3
3.2
4.2
5.0
–
–
–
1.2
2.2
3.2
4.2
–
–
–
–
2.3
2.1
1.9
1.7
1.4
1.3
0.8
–
–
4.3
3.7
3.1
2.2
–
–
–
1.3
2.3
3.2
4.1
5.0
5.8
6.8
–
–
2.1
3.0
3.9
5.0
–
–
–
2.6
2.4
2.2
1.9
1.7
1.7
1.5
1.0
–
4.8
4.3
3.6
3.1
2.1
–
–
1.3
2.3
3.1
4.0
4.9
5.7
6.7
7.6
–
2.0
2.9
3.8
4.8
5.9
–
–
2.7
2.6
2.4
2.2
2.0
1.9
1.7
1.6
–
5.3
4.9
4.2
3.7
3.1
2.2
–
1.3
2.2
3.1
4.0
4.9
5.7
6.6
7.5
–
1.9
2.7
3.6
4.6
5.6
6.7
–
2.9
2.8
2.6
2.4
2.2
2.0
1.9
1.9
–
–
5.4
4.9
4.3
3.6
3.1
–
1.2
2.1
3.1
3.9
4.7
5.7
6.5
7.5
–
–
2.6
3.5
4.4
5.4
6.5
–
3.1
3.0
2.8
2.6
2.4
2.3
2.2
2.2
–
–
5.8
5.3
4.8
4.3
3.7
3.1
1.2
2.1
3.0
3.9
4.7
5.6
6.5
7.5
–
–
2.5
3.3
4.3
5.3
5.9
7.3
20†
30
40
50
60
70
80
90
100
†For applications with liquid pressures below 30 psi (2 bar), request
end cap sub-assembly 21950-20-NYB.
Water
Pressure
30
40
50
60
70
80
90
100
Air Pressure*
1.2
23412, QJ25655
20†
In each line, figures in plain face indicate water atomized in gph (l/h) at
psi (bar) water pressure.
Air Pressure*
10
20
30
40
50
60
70
80
Figures in boldface indicate atomizing air in scfm (Nl/min) at psi (bar)
air pressure.
3.3
1.8
–
–
–
–
–
–
1.3
2.4
–
–
–
–
–
–
AirJet Fogger has a horizontal throwing distance of 15' (4.5 m) and will
expand to approximately 8' (2.4 m) wide/3' (.9 m) thick.
4.3
3.4
2.1
–
–
–
–
–
1.1
2.1
3.2
–
–
–
–
–
–
4.5
3.6
2.4
–
–
–
–
–
1.9
2.8
3.9
–
–
–
–
–
5.3
4.6
3.7
2.5
0.9
–
–
–
1.8
2.7
3.6
4.7
5.9
–
–
–
6.1
5.4
4.7
3.8
2.8
1.3
–
–
1.7
2.5
3.4
4.4
5.4
6.7
–
–
–
6.2
5.5
4.8
4.0
3.0
1.7
–
–
2.4
3.3
4.2
5.1
6.2
7.4
–
–
6.8
6.2
5.5
4.8
4.1
3.1
–
–
2.3
3.2
4.1
5.0
5.9
7.0
–
–
7.4
6.9
6.3
5.6
5.0
4.3
–
–
2.2
3.0
3.9
4.8
5.6
6.6
–
–
7.9
7.4
6.9
6.3
5.7
5.0
–
–
2.1
2.9
3.8
4.6
5.5
6.4
1. Values in blue area show optimum evaporation under normal room
conditions, when center line of spray is 5' (1.5 m) from the lower
surface.
2. Values in red area can require up to 10' (3 m) for evaporation. Other
values may be used where extended heat, higher air velocity exist or
where slight surface wetting is permitted.
F55
Air Atomizing
Nozzles
23412, QJ25655
DripSafe™
Special Purpose
• High-volume/high-efficiency air atomization.
• Air requirements are met using an air compressor with a
capacity range that is suitable for the application.
• Produces an adjustable, high-quality dry fog without wetting with
pressure-fed liquid.
• Requires minimal maintenance.
• Ideal for large/open structures and areas with high air exchange rates.
• The flat spray tip has a large orifice that reduces clogging.
• Operation is through a drip safe air-actuated liquid shut-off valve.
• Spray set-up and built-in strainer are quickly removed by
hand if cleaning is required.
• Automatically prevents liquid from spraying until air pressure at the
nozzle is sufficient for fine atomization.
• Spray tip is brass; valve and body polymer.
• Drip safe valve simplifies system construction and control while
improving performance.
• Operates at pressures up to 100 psi (7 bar) with a minimum
air pressure range of 25 to 35 psi (1.7 to 2.5 bar).
• Operates using normal water pressures found in municipal water
systems, eliminating the need for expensive, high-pressure hydraulic
pumps.
• A split-eyelet or saddle clamp version of the AirJet
Fogger (45269 Series) is also available for quick and easy
mounting to the liquid supply pipe.
45265
Optimization Tips
45269
Applications
• Evaporative cooling
• Insecticide spraying
• Fogging
• Plant propagation
• Humidification
Split-eyelet type to clamp on
pipe 1/2" to 1"
See Also
Specifications
Nozzle
Inlet
Conn.
(in.)
1/4
To Clamp On
Pipe
Size
(in.)
AirJet
Fogger
Type
45265
AirJet
Fogger
Type
1/2
3/4
1
45269
Fluid
Orifice
No.
Orifice
Dia.
Nom.
(in.)
16.0
.016
20
.020
26
.026
Fluid
Orifice
No.
Orifice
Dia.
Nom.
(in.)
16.0
.016
20
.020
26
.026
• Accessories
http://
– Pressure gauges
– Solenoid valves
– Strainers
• For 23412 and QJ25655, request Data Sheets 23412
and 25635
• For 45265 and 45269, request Data Sheets 45265-1-2
and 45269-1-2
F56
DripSafe™
Special Purpose
Performance Data
45265, 45269
Water
Pressure
20
30
40
Water
Pressure
Air Pressure*
10
20
30
40
50
60
70
80
10
20
30
40
50
60
70
80
1.1
–
–
–
–
–
–
3.1
1.7
–
–
–
–
–
–
1.5
2.5
–
–
–
–
–
–
1.4
2.8
–
–
–
–
–
–
1.7
1.5
1.2
–
–
–
–
–
3.6
2.1
1.7
–
–
–
–
–
1.4
2.4
3.4
–
–
–
–
–
1.3
2.5
3.6
–
–
–
–
–
2.0
1.7
1.5
1.4
–
–
–
–
4.3
3.1
2.2
–
–
–
–
–
1.4
2.4
3.3
4.2
–
–
–
–
1.2
2.3
3.4
–
–
–
–
–
20
30
40
In each line, figures in plain face indicate water atomized in gph (l/h)
at psi (bar) water pressure.
Water
Pressure
30
40
Air Pressure*
1.2
45265, 45269
20
Figures in boldface indicate atomizing air in scfm (Nl/min) at psi (bar)
air pressure.
Air Pressure*
10
20
30
40
50
60
70
80
3.3
1.8
–
–
–
–
–
–
1.3
2.4
–
–
–
–
–
–
4.3
3.4
2.1
–
–
–
–
–
1.1
2.1
3.2
–
–
–
–
–
–
4.5
3.6
2.4
–
–
–
–
–
1.9
2.8
3.9
–
–
–
–
1. Values in blue area show optimum evaporation under normal
room conditions, when center line of spray is 5' (1.5 m) from the
lower surface.
2. Values in red area can require up to 10' (3 m) for evaporation.
Other values may be used where extended heat, higher air
velocity exist or where slight surface wetting is permitted.
3. AirJet Fogger has a horizontal throwing distance of 15' (4.5 m)
and will expand to approximately 8' (2.4 m) wide/3' (.9 m) thick.
Ordering Info
Complete Nozzle
Assembly
Complete Nozzle
Assembly
45265 – 1/4 – 16
l
l
l
Nozzle
Body
Inlet
Conn.
Fluid
Orifice
Dia.
45269 – 1/2 – 16
l
l
l
Nozzle
Body
Pipe
Size
Fluid
Orifice
Dia.
BSPT connections require the addition of a “B” prior to the nozzle body
inlet connection.
F57
Air Atomizing
Nozzles
45265, 45269
Humidification Spray Nozzles and Units
• All equipment supplied for humidification systems except piping
and wiring.
• YMF MiniFogger® III is ideal for humidification applications with
limited space due to its compact design.
– Available with a choice of one to four stainless steel spray
nozzle set-ups with a wide variety of flow-rate sizes/droplet
sizes and types.
• 1/4JH siphon air atomizing nozzles provide automatic, efficient
humidity control with low installation and operating costs.
– Nozzles operate either with compressed air drawing water
from the float box by siphon action, or with water being
delivered to the nozzle under pressure.
– For each spray set-up, water capacity is 0.26 to 1.19 gph
(1.0 to 4.5 l/h), and air capacity is 30 to 35 nl/min at 43.5 psi
(3.0 bar).
– Produces a fine atomized spray for rapid evaporation and
efficient humidification.
– Can be placed in hard-to-reach spaces and can be easily
installed on a header, on a wall or on a ceiling.
– For information on siphon set-ups, see pages F23 to F53.
• 1/4JT pressure-fed air atomizing nozzles provide automatic,
efficient humidity control with low installation and operating
costs.
– 0.46 lbs. (210 g) for single spray set-up type; 0.55 lbs. (250 g)
for multiple four set-up types.
– Height is 4.53" (115 mm).
– Suitable for use in systems where water is under pressure.
– The body, retainer cap, and tank are made of corrosionresistant polypropylene with stainless steel air and water
connections.
– Have built-in strainers for air and water plus a ball check valve
in the water line.
– Materials are also compatible with deionized water.
– Produces a fine atomized spray for rapid evaporation and
efficient humidification.
• 46215-008 provides a finely atomized spray without the use of
compressed air.
– Produces a hollow cone spray pattern.
– For information on pressure set-ups, see pages F5 to F48.
• 45400 humidification unit is a self-contained humidifier suitable
for use with deionized water (DI).
– Easy to install on a wall or for use in non-ducted applications.
– Requires a minimum liquid pressure of 450 psi (31 bar)
to the nozzle.
– Maximum operating pressure of 1000 psi (69 bar).
– Air regulator and gauge, 24VDC air control solenoid and air line
filter are included within the Humidification Unit.
– Wall-mounting bracket is also provided.
– 9.7 lbs. (4.4 kg).
– For each spray set-up, water capacity ranges from 2.7 lbs./hr
at 10 psi (0.7 bar) air to 6.5 lbs./hr at 60 psi (4 bar) air.
1/4JH
45400
YMF
46215-008
Siphon inlet connection
1/4" NPT and BSPT inlets
1/4JT
MiniFogger III
air and liquid inlet connection
misting nozzle
Pressure-fed inlet connection
1/4" NPT and BSPT inlets
F58
Humidification Spray Nozzles and Units
Optimization Tips
Materials
Material
Code
Material
See Also
http://
Nozzle Type
JH
JT 45400 YMF 46215
Nozzle Bodies
Brass
(none)
– Pressure gauges
Nickel-plated Brass
(none)
– Solenoid valves
Kynar®
KY
303 Stainless Steel
– Strainers
• For 1/4JH siphon air atomizing nozzles, request
Data Sheet 10188
• For 1/4JT pressure-fed air atomizing nozzles, request
Data Sheet 2843
l
l
SS
l
l
Nickel-plated Brass
SSBR
l
l
SSBR
l
l
l
l
l
Air/Fluid Caps
• For 45400 humidification unit, request Data Sheet 45400
• For YMF MiniFogger® III, request Data Sheet YMF
Performance Data
l
Kynar
KY
303 Stainless Steel
SS
PTFE
TEF
l
l
l
Ordering Info
YMF MiniFogger III
Data per Nozzle (Air Pressure 0.3 MPa)
Orifice
Set-up
Air
Mean
Spray
Diameter Liquid
No.
Capacity Capacity Droplet Size Distance
(in.)
gph
scfm
(micron)*
(ft.)
SU2.5N
0.02
.66
1.2
8.5
8.8
*Sauter Mean Diameter
0.1 MPa = 1 bar
1/4 JH – SS
l
l
l
Inlet
Conn.
Nozzle
Body
Material
Code
Spray Set-up
+
SU1A –
l
Spray
Set-up
No.
SS
l
Material
Code
Humidification
Unit
YMF-3 –
l
Humidification
Unit
Type
4
l
No.
of
Set-ups
45400
46215-008
Atomizing
Air
Nozzle Body*
Water
Capacity
Air
Press.
psi
Air
Capacity
scfm
gph
10
.38
.32
20
.57
.42
30
.74
.52
40
.92
.62
50
1.10
.71
60
1.30
.78
Pressure
psi
Liquid
Capacity
gph
500
.94
600
1.0
700
1.1
800
1.2
900
1.25
1000
1.3
To order spray set-up only, use spray set-up number and
material code: SU1A-SS.
Humidification
Unit
45400 –
l
Humidification
Unit
Type
1
l
No.
of
Set-ups
connection, nozzle body and material code: 1/4JH-SS.
Typical humidifying set-ups for siphon nozzles
B
A
A – Float box with float valve
B – TW liquid strainer
C – Air atomizing nozzle
D – Spray pipe assembly
E – Pipe hanger
F – Air filter
G – Pressure regulator with gauge
H – Solenoid valve
I – Switching relay
J – Humidistat
C
I
D
E
J
G
F H
F59
Air Atomizing
Nozzles
• Accessories
Humidification System Components
• 2335-SE pipe assembly consists of straight and formed tubing
with fittings, globe valve and split-eyelet connectors.
– Not assembled.
• 11438-85 humidistat will respond to humidity levels in the
range of 20% to 95% RH.
– Maximum operating temperature 125°F (52°C). 24V DC; 110V.
Overall height 6" (15 cm).
• 11438-95 switching relay has built-in transformer that supplies
low-voltage current for humidistat circuit.
– 2-wire 24V control, 115V AC. Maximum temperature 115°F
(46°C).
• 55089 electric humidistat quick relative humidity LCD readouts
from 1% to 99% with repeatability of ±5%.
– Operating temperature range 32°F to 160°F (0°C to 71°C).
– 24V (DC or AC).
• 45604 float valve used in 45600 float box to shut off inlet flow
at a preset water level.
– Made of ABS plastic, 304 Stainless Steel, polypropylene
with fiber washers and a brass nut.
• 55400 valve package is easy to install and use – simply connect
to existing air and fluid lines.
– The NEMA type 4 panel is completely sealed to eliminate moisture
damage to components.
– Safety feature ensures there is no product damage due to
unintentional water release.
– Stainless steel components available for use with deionized water.
– Separate atomizing and cylinder air lines with adjustable delay
time assures liquid atomization.
• 2202 pipe hanger for proper spacing between air and liquid lines.
Sizes fit 1/2" piping.
– Hanger is held by threaded rod and nuts (not included) for
vertical adjustment.
– Made of cast aluminum. 4" (10 cm) spacing.
– Use with 2335-SE spray pipe assembly.
See Also
• Accessories
Optimization Tips
http://
– Pressure gauges
– Solenoid valves
– Strainers
• Section L, Accessories
• For 2335-SE pipe assembly, request Data Sheet 2335-SE
• For 55089 electrical humidistat, request Data Sheet 55089
2335-SE
Spray pipe assembly
45604
Float valve
11438-85
11438-95
Humidistat
Switching relay
45600
55400
Float box
Valve package
55089
Electric humidistat
2202
Pipe hanger
F60
Air Atomizing Accessories
• 22140 pressure tank assembly meets ASME® Boiler and Pressure
Vessel Code requirements and OSHA safety regulations.
– Constructed of 304 Stainless Steel.
• 39272 tank heater bands provide anywhere from 6°F to 60°F (3°C
to 33°C) heat gain depending upon the tank size and number of
bands used.
– Silicone rubber construction with fiberglass mesh
reinforcement for added strength, flexibility, and corrosion
resistance.
– Assembly includes a pressure regulator with gauge, ASME
coded pressure relief valve, air bleed valve and plug valves
for air inlet and liquid outlet.
– Features quick-release band clasp and built-in thermostat for
temperature control.
– Tanks are available in 1, 2, 5 and 10 gallon (3.8, 7.6, 18.9 and
38 liter) capacities.
– Two sizes fit 9" and 12" (288.6 and 304.8 mm) diameter tanks.
– The air inlet and liquid outlet have 1/4" NPT (F) connections.
• 38673 push-in tube fittings provide fast and easy hook-up of
air atomizing nozzles.
– The maximum working pressure is 140 psi at 100°F (9.5 bar
at 38°C).
– Select from six configurations with 1/8", 1/4" or 3/8" NPT (M)
connections for 1/4", 3/8" and 1/2" O.D. tubing.
• 45592 ferrule-type tube fittings are intended for use when
operating at higher pressures.
– The 316 Stainless Steel is of durable construction and can be
easily taken apart for cleaning.
– Recommended pressure is up to 250 psi (17 bar) for liquid
and air lines.
– Six configurations available with 1/8", 1/4" or 3/8" NPT
connections for 1/4", 3/8" and 1/2" O.D. tubing.
• 38691 and 38692 strong, semi-rigid nylon tubes designed for use
with 38673 fittings.
– Abrasion resistant and dimensionally stable tubing available in
12', 25' and 50' (3.6 m, 7.5 m and 15 m) lengths.
– Fits 1/2", 3/4" or 1" pipe or similar O.D. tube. 1/4" NPT or
BSPT (M) outlet pipe connections.
– Nickel-plated brass with zinc-plated pipe clamps or all
stainless steel construction.
• 39273, 39275 level switch kit indicates a low liquid level condition
inside the pressure tank.
– Use standard 39273 level switch with 5 and 10 gallon (18 and
38 liter) pressure tank assemblies with external 1/4" NPT (F)
threads.
– Maximum working pressure is 250 psi (17 bar) at –40°F to +70°F
(–40°C to +20°C).
– 38691 has 1/4" O.D.
– 38692 has 3/8" O.D.
– Use 39275 level switch with 1 and 2 gallon (4 and 8 liter)
pressure tank assemblies with external 1/4" NPT (F) threads.
– Features a U.L. listed float switch, quick disconnect and 12'
(3 m) PVC jacketed cable.
– Available in brass with Buna-N float or all stainless steel.
F61
Air Atomizing
Nozzles
– Durable nickel-plated brass construction includes Buna-N
O-ring.
– The 22140 features brass fittings and an EPR lid seal.
• 38180 split-eyelet swivel union simplifies installation and
maintenance of air atomizing nozzles and spray guns.
– Connector design reduces costs by eliminating cutting,
threading, welding and brazing operations and adjustment
of fittings, unions and nipples.
Air Atomizing Accessories
22140
Pressure tank assembly
38180
Split-eyelet swivel union
39273 and
39275
Level switch kit
38673 and
45592
Tube fittings
39272
Tank heater bands
Optimization Tips
See Also
• For 22140 pressure tank assembly, request Data Sheet 22140
http://
• For 38180 split-eyelet swivel union, request Data Sheet 38180
• For 39273, 39275 level switch kit, request Data Sheet 39275 and 39273
• For 39272 tank heater bands, request Data Sheet 39272
• For 38673, request Data Sheet 38673
• For 45592 ferrule-type tube fittings, request Data Sheet 45592
• For 38691 and 38692, request Data Sheets 38691 and 38692
F62

Section F – Air Atomizing Spray Nozzles

Transcription

Similar documents

Section F – Air Atomizing Spray Nozzles