Dexion`s Brochure on Shelving and Racking Solutions

STORAGE SOLUTIONS TAILORED
TO YOUR NEEDS.
As the demands on business continue to escalate, so too the need
for fast, accurate storage, handling and distribution becomes
increasingly critical to business performance.
Dexion specialises in designing storage systems that make industry
function more productively and profitably. From binning and shelving to
pallet racking and carton storage with fully integrated control systems,
Dexion tailors storage solutions to meet any - and every - need.
NEED MORE INFORMATION?
Contact your authorised Dexion supplier and ask for a copy of
The Dexion Guide To Pallet Handling Systems and a copy of our
Lifetime Warranty brochure.
Dexion (Australia) Pty Limited ABN 83 000 083 956
Head Office: Tattersall Road, Blacktown NSW 2148 Ph +61 2 9830 5000 Fax +61 2 9830 5001
www.dexion.biz
Dexion is a member of the Dexion Group. The following are registered trademarks: DEXION, Keylock,
Speedlock and Compactus. Whilst the utmost care is taken to ensure the accuracy of the information
contained herein it is provided in the understanding that the company shall under no circumstances be
liable for any injuries, expenses or other losses which may in any way be attributable to the use or adoption
of such data and/or design details. All dimensions indicated are nominal only. Dexion (Australia) Pty
Limited reserves the right to alter or amend without prior notice data and design details specified herein.
IND/12/02
STORAGE SYSTEMS DESIGNED TO MAKE
B U S I N E S S M O R E P R O D U C T I V E A N D P R O F I TA B L E .
DESIGNED TO BE THE BEST
Dexion is Australia’s largest single designer, manufacturer and
supplier of product storage equipment. It is also the only Australian
manufacturer that is part of an international company that
specialises in product storage.
Local knowledge. International strength.
Dexion operates in over 50 countries around the world. Its global
operations bring unrivalled design, technology, expertise and
manufacturing resources to the Australian marketplace together
with access to a range of highly sophisticated products that can only
be produced for international markets.
Setting the standards.
For over 50 years, Dexion has set the standards that others have
followed. Today, nothing has changed. Dexion is committed to
producing the best industrial storage products on earth in every
major category from pallet racking to shelving, dynamic storage
systems and binning.
An unparalleled commitment to research and development combines
with highly sophisticated manufacturing facilities, both in Australia
and around the world, keeping Dexion at the forefront of storage
system technology, performance and cost effectiveness.
Systems tailored to your needs.
From shelves and binning to pallet racking suited to everything from
small storage facilities with a few bays of racking to large scale
warehouses measuring in the millions of cubic metres, Dexion tailors
storage solutions to your needs.
When it comes to supply chain knowledge and storage that makes
business function productively and profitably, get the best in the
world – from Dexion.
Precision robotic welding ensures fail-safe
performance of all Dexion components.
2
3
THE MOST TECHNOLOGICALLY ADVANCED
PALLET STORAGE SYSTEM EVER CREATED.
Dexion Keylock has led the world in pallet storage for many years.
But to stay at the forefront of storage and handling technology (and
even further ahead of the competition), we made it even better.
We took the best pallet racking system in the world
– and made it better.
Today’s Keylock was developed by an international team that saw an
elite group of Australian engineers work with Dexion’s Global Design
Department to create a system that married international technology
and manufacturing techniques with Australian design requirements.
The result is a triumph of technology and design that lifts pallet
racking to a new level of engineering sophistication and performance
excellence. Keylock has been designed to be the best in the world –
and it lives up to every expectation.
- Uprights and beams feature revolutionary new profiles. The unique
contours and new technologies such as tox stitching provide a load
bearing capacity that far exceeds conventional designs.
- There’s an extensive range of beams available from conventional
A typical installation in the
largest installed base of
pallet racking in Australia.
boxed and channel beams through to a revolutionary new I -Beam.
- Keylock remains compatible with preceding designs.
- Frame and beam sections come in a variety of sizes to
accommodate light and heavy duty needs.
- The symmetrically stiffened upright and beam
profiles maximise load bearing strength and
improve damage resistance.
The clearway between the connector and
upright enables easy adjustment of beams.
4
5
A SYSTEM IS ONLY AS GOOD
AS THE SUM OF ALL ITS PARTS.
DESIGNED FROM THE GROUND UP TO BE
STRONGER, LIGHTER AND MORE VERSATILE.
Every component of the Keylock system has been designed
Uprights bear the full load of the pallet racking system. The transfer
and engineered to fit the most stringent design criteria and
of rack loads from the beams through the uprights is therefore
global standards.
critical to overall system strength, safety and performance.
We’ve added strength where necessary. Enhanced design features
Strength where you need it.
for greater flexibility and versatility. Improved impact resistance.
Made it easier to construct – and dismantle. And made it safer to
build – and to use.
Beams, uprights, connectors, base plates and bracing have been recently
redesigned. Component versus component, they’re the best in the
world, but it’s how they come together that makes Keylock unique.
The Keylock upright is designed to carry the rack load on the front
face – without twisting, distorting or stressing metal.
Connecting slots are positioned 14mm from the edges and take less
than 9% of the load bearing section. Conventional uprights often
locate slots less than 10mm from the edge and remove up to 2.5
times the amount of steel from the face.
Uprights are available in painted
or pre-galvanised finish.
It is a system that comes together – perfectly. It’s engineered to
perform above it’s stated criteria. And more importantly, it’s
professionally tested time and time again to ensure it does.
The profile of the slots transfers the load vertically down the upright
and allows beams to connect without being wedged in so that side
loads are not imposed on the upright by the beam end connector.
A breakthrough in design, construction and materials.
Keylock uprights have a significantly deeper flange (side face) than
- Advanced engineering technologies and destruction testing has
delivered unsurpassed strength, flexibility and functional efficiency.
other conventional racking systems, providing greater overall strength
and rigidity and greater resistance to lateral impact damage.
Additional holes have been added to the back of the upright so base
plates can be fitted lower down for improved strength and rigidity.
- Uprights feature a symmetrically stiffened profile to maximise load
bearing strength and structural robustness of the racking.
- Uprights are available in lengths up to 8 metres and fit
easily together to meet any height requirement – and
they are reversible.
The I-Beam is designed to meet the
requirements of Australian Standard
4084, SEMA, FEM and RMI.
- Should accidental damage occur, it is restricted to the
obvious
areas,
rather
than
being
transmitted
throughout the racking structure.
- There is an extensive range of baseplates from 4mm to
12mm thick.
6
Base plates connect low on the upright
adding strength to the structure.
7
A COMPREHENSIVE RANGE OF BEAMS FOR
EVERY PURPOSE.
Keylock includes a full range of beams that includes the revolutionary
I-Beam, the world standard setting Dexion boxed beam and a range
of special application beams including open, channel, stepped and
The best boxed beam in the world.
Dexion created the first boxed beam, and the world followed. But
today’s Keylock boxed beam is again streets ahead of the
competition.
- The Keylock boxed beam is a robust design strengthened by unique
rolled flanges. The two sections that form the beam are joined
RHS beams.
down its entire length.
- Conventional boxed beams are often little more than two channels
tack welded together. Even a slight lateral impact can cause these
channels to separate.
The world’s best beam is well connected.
Fully welded box beam.
The connector is the vital link between the pallet rack’s load bearing
The revolutionary new I-Beam
beams and uprights. The Keylock connector creates a clearway
between the side flange of the upright and the beam, ensuring the
At the heart of the new Keylock system is Dexion’s I-beam - a
load is safely carried on the front face of the upright where it belongs
revolutionary design that has enabled a significant reduction in
without ever touching or loading the side of the upright.
weight to improve handling and construction without compromising
resistance to damage or load capacity.
Unique Dexion safety lock system.
- An automatic safety lock engages the second the connector clicks
- The I-beam profile distributes weight evenly around the total
perimeter of the section, reducing areas of excessive stress, and
into place, so there’s no chance of beams and uprights
accidentally parting.
thus optimising load carrying capacity.
- The Dexion safety lock is designed to prevent inadvertent
- The I-Beam is structurally more efficient than conventional box
dislodging of a beam through careless operation. It is also
beams of the same weight, so the same load can be carried by an
designed to sheer when excessive load is applied, thus preventing
I-Beam that is lighter, easier to handle and quicker to construct.
damage.
- The I-Beam is designed to resist lateral loads and
accidental damage.
- Using a patented new system known as Tox
Tox Stitching
Stitching, we’ve created a strong, rigid beam that
actually strengthens the structure. Unlike a tack
welded box beam, the tox stitched I-Beam will not
part with lateral pressure.
Strip welded I-Beam
Tox Stitching
8
9
SELECTIVE PALLET RACKING
Selective Pallet Racking is a cost effective storage system providing
direct access to all pallets. It provides high capacity storage, is easily
installed and adjusted, and has low equipment and capital costs.
- Pallets can be located, accessed and moved individually.
- Rapid handling of almost all types of palletised goods.
- Infinitely adjustable and offering a wide range of options and
components to accommodate specialised needs.
- Maximises space use in any warehouse configuration while
retaining optimum product accessibility.
- Strength and rigidity prevents compression damage to goods.
- Bottom level of pallets can be stored on the floor, lowering
structure costs.
% Average locations used
90%
% Immediate accessibility
100%
Stock rotation
Good
% Floor utilisation
40%
The wide selection of beam
sections and lengths provides for
tailor made heavy duty shelving.
10
11
NARROW AISLE RACKING
- Makes optimum use of floor area and roof height.
- High density storage with direct access to all pallets.
- The system is served by forklift machines with the mast
or fork head rotating to left or right as required.
- Operator cabins may be elevating or static.
% Average locations used 90%
% Immediate accessibility 100%
Stock rotation
Good
% Floor utilisation
45%
DOUBLE DEEP RACKING
Double Deep Racking stores two pallets deep, or four pallets deep in
a double entry rack. The system requires the use of a special reach
truck with either dual pantograph or sliding fork attachments.
- Can be protected against fork truck operator error and accidental
impact damage.
- Features frame and beam sections for light and heavy duty needs.
- Upper levels can be fitted with guide rails to assist in locating pallets.
% Average locations used 90%
% Immediate accessibility
Stock rotation
% Floor utilisation
12
50%
Average
60%
13
DEEPSTOR HIGH DENSITY DRIVE-IN RACKING
Most high density drive-in pallet racking systems are little more than
conventional pallet racks, adapted and reinforced to meet the
stringent demands of drive-in applications.
Dexion’s Deepstor is a revolutionary drive-in racking system purpose
designed to provide the space efficiency and high volume storage of
block stacking, with easy access to pallets.
Unique self centreing rails automatically position pallets quickly and
safely, eliminating time consuming realignment.
There are no aisles and no cross beams, providing maximum space
efficiency. And because each pallet sits on its own support rails,
Unique self centring rails
position pallets quickly and easily
pallets are no longer stacked on top of each other.
Stable and highly space efficient, Deepstor provides maximum use of
storage volume together with fast input and retrieval of pallets.
1445 BAY CLEAR ENTRY
87.5 CLEAR
OH=50
- Available up to 12 metres high, Deepstor is tailored to pallet and
62.5
load size and handling equipment.
1045
200 SUPPORT ARM
- Can be used with standard handling equipment.
Pallets with load overhang
- Rails adjust in 50mm increments to optimise space utilisation.
- Low profile cantilever arms maximise storage capacity.
1355 BAY CLEAR ENTRY
92.5 CLEAR
62.5
1045
155 SUPPORT ARM
Pallets without load overhang
Deepstor has a range of standard
damage protection systems
14
15
DYNAMIC PALLET STORAGE SYSTEMS
Dexion gravity fed and powered mobile pallet storage systems offer
the flexibility to tailor installations to your exact requirements,
maximising both operating efficiency and storage capacity.
Pallet Flow Through
Pallets are placed on rollers that slope slightly downward. They are
fed in from one side, and retrieved from the opposite side.
- Very high density storage with up to 12 pallets in each bay.
- Eliminate double handling from receiving area.
- Gravity feed automatically replenishes the pick face.
- Automatic Braking System controls pallet speed ensuring pallets
are maintained end to end.
- Fork trucks never enter the rack.
PALLET OUT
PALLET IN
Pallet Push Back
Pallet Push Back operates on Last In, First Out. Pallets are gravity
fed to the front and are stored and retrieved from the same aisle.
- Highly efficient use of space
- Reduces handling
PALLET IN
& OUT
- Fork trucks never enter the rack
Movo Mobile Pallet Racking
Creates a single aisle between a block of racks when and where you
need it, by rolling power driven racks along the track system.
- Movo can be installed using existing racking structures.
- Powered aisle opening can be remote radio controlled, saving time
and improving efficiency.
- Storage capacity of ‘block’ racking without restricted access.
16
17
PALLET RACKING MAJOR COMPONENTS
PALLET RACKING ACCESSORIES
The Keylock System
Rack Protection
Dexion Keylock is one of the easiest pallet storage systems in the world to
Any damage to racking will reduce its load carrying capacity. Dexion provides
design and construct. It can be configured as either a single entry or double
a range of rack protection accessories designed to safeguard racks from
entry rack. The basic rack consists of:
accidental damage. Rack protection accessories include: Column Guards,
Rack Sentry, Offset Racks, Upright Protectors and Step Back Racks.
Frames: Two upright members joined together by bolted bracing.
Column Guards
Beams: Horizontal load bearing members that slot into the uprights.
The Column Guard is bolted to the floor in front of the uprights to a height of
Uprights
360mm providing protection from forklifts to the bottom portion of the upright.
A wide variety of upright grades can be used to provide rack heights up to
Column Guard
Rack Sentry
30 metres. Uprights are punched with symmetric hexagonal slots at 76mm
intervals for beam height adjustment and are reversible. Keylock uprights
are available in either a lead free painted finish or pre-galvanised finish.
Rack Sentry is a revolution in rack protection. It’s moulded from a semiflexible, stress resistant plastic and uses a patented air cushion system.
It’s ultra light to handle, installed in seconds using velcro straps and brightly
Baseplates
coloured for greater visibility. It is also easily removed for relocation.
Rack Sentry
Baseplates provide a smooth bearing surface for the upright, spread the
load of the upright over a larger area of the floor, provide a means of
securing the upright to the concrete floor and a means of levelling the rack.
Dexion has an extensive range of baseplates to satisfy virtually every need.
Beam End Connectors
Storage accessories
A range of accessories are available to tailor pallet racking to specific needs
and applications. Standard accessories include:
Pallet Support Bars
All beams are factory welded to beam end connectors and fitted with safety
locks that are designed to resist accidental uplift from pallet handling equipment.
Supported at each end by the beams, Pallet Support Beams provide a
secondary support member for pallet racking or shelving. The Pallet Support
Beams
Bar is designed to have its top surface approximately flush with the beams.
There are six beam types available as standard: I-Beam, boxed beam, open
Fork Entry Bars
beam, channel beam, stepped beam and RHS beam.
Pallet Support Bars
These are used when unsuitable pallets or unpalletised loads are to be
stored on beams and handled by forklift trucks. The Bars provide a gap of
approximately 75mm above the beam for forks.
Fork Entry Bars
Mesh Decks
Clip on Wire Mesh Decks minimise the build up of dust and increase light and
visibility in warehouses. Standard sizes are 1350mm x 840mm and 1250mm
x 840mm. Both are available as standard or heavy duty.
I-Beam
18
Boxed
Beam
Open
Beam
Channel
Beam
Stepped
Beam
Mesh Decks
RHS
Beam
19
SPANDEX SHELVING SYSTEMS
Spandex industrial shelving is a sturdy, versatile and easily assembled
storage system that provides heavy duty capacities at low duty
prices.
Spandex’s close tolerance high performance components make it
suitable for high rise and multi-tier applications.
Spandex Multi Tier utilises unused head room providing greater
storage efficiency.
Spandex Industrial is strong and durable, catering for bay loads of up
to 1500kg in bay widths of either 900mm or 1200mm.
From one or two bays to major installations, Dexion Spandex is quick
to install and extremely cost effective. And because Spandex is used
by so many companies and in so many applications right across
Australia, it is readily available.
Spandex meets the robust
requirements of machine shops, parts
stores and warehouses, yet looks
smart for office and point of sale use.
21
ULTIMA
Ultima is a revolutionary shelving system made in Dexion’s state-ofthe-art manufacturing facility in Europe.
Unparalleled quality, precision engineering and adaptability make
Ultima the best large scale shelving system in the world.
Ideally suited to large projects, Ultima combines the structural
strength required to form multiple tiers, bridges and walkways with
the flexibility necessary to accommodate a broad range of storage
and order fulfilment needs.
An extensive range of purpose designed accessories form an integral
part of the Ultima system. Each one is tailored to specific needs, fits
perfectly, and functions flawlessly.
Components slot together forming a rigid, durable structure that’s
quick and easy to assemble, rearrange or dismantle for relocation.
Ultima is a versatile, heavy duty shelving system with:
- Infinite flexibility with heights from 1 to 15 metres, depths from
300 to 1000mm and shelf widths from 765 to 2500mm.
- Load capacity up to 400kgs per shelf and over 5 tonnes per bay.
Ultima is suitable for large scale
and multi-tier designs.
- Can be constructed in single tier or
multi-tier with suspended walkways,
mobile shelving or over-rack platforms.
- Product can be accessed from either
side as there are no support braces.
- Adapts to future needs including fully
automated product picking.
Accessories
Ultima’s accessories include drawers,
lockable doors, plastic bins, tyre racks,
shelf dividers and retractable desks.
22
23
LONGSPAN
Longspan is a strong, durable, versatile – and economical – shelving
system that looks good and minimises lost space from uprights
making it ideal for a wide variety of applications from archives to
automotive, factories, warehouses, retail, wholesale and commercial.
- High density storage of small items
- Storage of large, heavy and bulky items
- Storage of long, odd-shaped or awkward items
Two beam styles are available One-Piece and Heavy Duty. Both rotate
giving a choice of step or flat top.
Long and strong yet easy to install
Longspan has fully adjustable shelf heights, spans of up to
2710∑mm, shelf loads up to 700kg and a bay load capacity in excess
of 5 tonnes, so it’s suitable for everything from small parts through
to long, heavy or bulky goods. And because it uses a modular design
and bolt-free lock-in system requiring no special tools, it’s installed in
minutes.
Single tier, multi-tier, high rise, mobile and more
Beams clip quickly and easily into
uprights without bolting and are secured
with a safety lock
Longspan’s versatility gives one system for a diversity of needs:
- Multi-Tier maximises storage capacity of small to medium items
- High-Rise configurations meet the demands of high density narrowaisle and automated stock picking systems
- Mounted on mobile bases, Longspan provides high density storage
for less frequently accessed small to medium size items
- Carton Live Storage configurations suit order picking applications
Bolted frames for strength and reliability
Multi-tier installations provide
high capacity with cost effective use
of available height
Longspan incorporates a wide range of beams and frames making it
easy to customise to precise storage needs. Different bay lengths
can be combined to store a wide range of items while purpose
designed accessories extend versatility even further.
- The range of beams and frames make it easy to customise
structures to specific requirements and building dimensions.
- Combines high density storage with the flexibility to adapt to
changing needs and changing product lines.
- Steel, timber or wire shelves that can be loaded from both sides.
24
Longspan’s versatile modular
design makes it suitable for a wide
variety of applications
25
The Marlbro system consists
of end frames, beams and
shelves which clip together easily
Like all Dexion shelving, Marlbro converts to mobile storage for higher capacity
MARLBRO SHELVING
Marlbro is strong, easily adjusted and simple to build. Its beams clip
easily into the pre-punched frames and the wire shelves drop into
position. Marlbro can also be readily relocated once constructed.
Although designed as an all purpose shelving system, Marlbro’s nonporous, corrosion resistant finish make it particularly suitable for
cold storage.
- Electroplated zinc finish with a special lacquer dip to decrease the
risk of food contamination.
- Suitable for linen storage in hotels, merchandising and cold
storage. Also suitable for home, office and archive storage.
Attractive and corrosion
resistant, Marlbro is well suited
to retail operations
- Marlbro can be incorporated into a Compactus Freetrack system
to maximise use of valuable floor space.
26
27
SLOTTED ANGLE
Slotted Angle provides simple, cost-efficient solutions for virtually any
storage requirement. The unique pre-punched hole pattern allows
multiple steel sections to be bolted together to form sturdy shelving
and storage systems.
Combining steel shelves with Slotted Angle uprights provides one of
the most versatile and economical shelving systems available.
Shelves range in depth from 300mm to 900mm. Standard width is
900mm and an option of 1200mm is also available.
With a wide range of heights, depths and lengths, Slotted Angle is a
quick and easy storage solution for stores, workshops, warehouses
and wherever a cost effective and easily assembled shelving unit
makes a difference.
- Slotted Angle is used in a wide variety of applications including
shelving, benches, trolleys and light construction work.
- It is sturdy, tough, adaptable, rigid when assembled, easy to
relocate and ideal for special purpose designs.
160 ANGLE
Size: 40mm x 40mm X 1.8mm.
3810mm lengths.
2286mm lengths.
(Cut to size lengths also available).
225 ANGLE
Size: 62mm x 41mm X 1.8mm.
3810mm lengths.
(Cut to size lengths also available).
260 ANGLE
Size: 66mm x 44.4mm X 2.5mm.
3810mm lengths.
(Cut to size lengths also available).
Components are
available in enamel finish
for lasting protection
PUNCHED STRAP
Size: 38mm x 1.8mm.
3048mm lengths.
NUTS AND BOLTS
Standard: Hexagon head.
8mm x 16mm long.
Zinc plated. Packs of 100.
CORNER PLATES
Used for bracing Slotted Angle structures.
BASE PLATES
Used to spread load.
28
29
BULK AND ARCHIVE MOBILE STORAGE SYSTEMS
Compactus Multi-Bay
Compactus Multi-Bay achieves maximum space saving in the office
or small archival environment. Its fixed floor track caters for uneven
floor surfaces.
- Base lengths up to 6.6 metres.
- Crank-Driven to move block-loads up to 20 tonnes.
Application Guide:
Ideal for the bulk storage of any regularly accessed item in the
office, retail storage area, library, warehouse or small archive.
Compactus Archive
Multi-Bay’s design
lines complement today’s
office décor
Compactus Archive is a state-of-the-art, high volume storage unit. Its
variable gearing enables the operator to move very heavy loads of up
to 40 tonnes with absolute ease.
- Base lengths up to 17 metres.
- Crank-driven to move loads up to 40.5 tonnes.
Application Guide:
Exacting standards to stand the test-of-time. Is the
leading system for the long-term storage of items
in archives, museums, libraries and galleries.
Compactus Power3
Compactus Power3 offers high capacity storage with a wide range of
intelligent operating functions controlled through a ‘one-touch’ pad.
- Soft start and stop ensures vibration-free, safe movement.
Stopping distance can be adjusted.
- Programmable using transponder keys or via your PC. Has easily
set access authorisations.
- Can be linked to climate control, lighting or fire alarms. It also has
a night time setting option.
Application Guide:
Ideal for the bulk storage of documents or items that are
frequently accessed, or where long-term security is a priority.
30
31
SELECTA-FLO
Dexion Selecta-Flo is a gravity fed order picking system designed to
increase order picking efficiency while saving on valuable floor-space.
- Selecta-Flo delivers efficient full-carton and split carton order
picking with low capital outlay and low operational costs.
- Saves on labour by providing a more orderly picking system. Order
pickers work in the front aisle while replenishers work in the back
aisle, completely separated from the pickers.
By presenting the widest range of products within easy reach of
order pickers, Selecta-Flo eliminates much of the walking and
searching time. The ‘items picked per hour’ is dramatically increased.
- Selecta-Flo reduces labour costs and increases efficiency.
- It is strong, modular and uses gravity, so has no running cost.
Standard bed
with same length
- Provides automatic stock rotation and allows instant stock checks.
- Dexion Selecta-Flo is your answer to live storage order picking.
Standard bed with variable
length for a lane jutting out
Shallow drop-out tray for
picking out of carton
Deep drop-out tray for
picking out of carton
With Selecta-Flo, first-in first-out
stock rotation in any given storage
lane is assured, which is essential
when handling perishable goods
32
33
MAXI BINS
Louvred Panels form the Backbone of the
Maxi Small Parts Storage System.
Maxi Bins are is a flexible small parts storage system with seven bin
sizes, five colours and louvred panels that enable you to design your
LP72 – 1829mm.
LP36 – 914mm.
The steel panels allow all sizes of Maxi Bins to hang in a high density
LP18 – 457mm.
own system.
configuration. Panels are finished in Grey.
The Dexion Maxi range has bins that stack and bins that divide.
Panels are 457mm wide and can support 68kg of stock for
There are accessories from hooks, hangers and trolleys and
each 305mm height of panel. Single sided panels available in
demountable panels as well as large scale binning systems.
three heights.
Free Standing Racks
P30
P20
Double sided panels with rack feet (rack feet sold separately)
– available in two heights – 1375mm and 1840mm.
P10
P60
P5
Bench Unit
A small free standing louvred panel for bench top and workstation
use. Size: 457mm square. Finish: Grey.
P40
P45
STACK-A-BINS
Available in a variety of shapes sizes and configurations to suit
individual storage needs, Stack-A-Bins can be stacked, mounted on
walls or mounted on Dexion Maxi louvred panels.
Ref.
Width
Depth
Height
mm
mm
mm
Dividers
(Optional Extra)
Maximum
Loading
Panel*
Density
kg
Stack-A-Bins are light in weight, easy to handle and non-porous. The
range includes: Visi-Paks, Spare Parts Trays and Drawer Organisers.
P5
100
120
60
N/C
2
52.5
P10
100
178
85
N/C
5
35.0
P20
135
225
125
N/C
9
19.7
P30
205
280
165
ONE
14
10.5
P40
410
280
165
TWO
18
5.3
Peg Board Hanger
P45
160
425
130
SEVEN
13
6.5
Chrome plated hangers enable P5 and
P60
410
457
216
THREE
27
4.4
P10 Maxi bins to be hung on peg-board.
* Panel density is the approximate number of bins that will
fit into a linear metre of standard 457mm wide panel.
Louvred Panel Hooks
Hooks are available to hang awkward items.
SELF STACKED BINS
The interlocking design of Maxi Bins ensures secure stacking and
prevents the bin from splaying under load. The P5 bins slot together
for easy carrying. The P30 and P40 have recessed handholds. The
P60 has a removable zinc plated bar, which facilitates easy stacking
of full bins.
Made from high
impact styrene,
Drawer Organisers
are a convenient,
free standing
drawer unit for
small parts storage
35
RAISED STORAGE AREAS
A raised storage system is the fast way to add extra floor space
within the shell of an existing building. In fact, you can virtually double
your floor space without changing premises - or increasing your rent.
Raised storage areas provide the means to create separate zones
within one centralised facility, so you can separate areas for bulky
items, fragile items, warehousing and despatch, fast-moving and
slow-moving stock, and so on.
Each installation is tailored to the site and the load-bearing
performance required – maximising economy and safety.
Racking Application
- Raised storage areas made from Dexion racking are quick to install
and are compatible with most existing warehouse storage systems.
- Longspan shelves are readily added above or below floor.
Shelving Application
- Low on cost, high on versatility, Dexion shelving is the fast,
economical way to add a raised storage area.
- Open or closed framework for security or air circulation.
Double your storage space with a raised storage
area. Raised areas can be added to either part or
all of most existing single level storage systems.
36
37
CLEARSPAN
Dexion Clearspan is a cost efficient adjustable light duty cantilever
racking system designed to accommodate long and awkward loads.
It provides easy accessability together with support along the full
length of the item being stored.
Clearspan is available in both single sided and double sided
configurations. The double sided rack provides maximum storage
capacity on a single central column while the single sided rack is
designed to fit flush against a wall.
Compatibility with other storage equipment
Low initial costs, reduced handling
costs and effective use of space
Dexion’s proven Keylock pallet racking components are used to
construct Clearspan, so different options can be easily and
economically designed and built to meet specific requirements.
- Suitable for storage of extra long or awkwardly shaped items.
- Allows for optimal use of horizontal space when storing bulky items
ROLLRACK
like furniture and white goods or long items like timber and steel.
Dexion Rollrack is purpose designed for storing long and easily
damaged materials such as rods, piping and beams.
The rack contains a number of cradles, each fitted with ball-bearing
- Storage arms are connected to the upright frame allowing easy
adjustment of the arms at 76mm increments.
- Arms can be placed at desired levels to fully utilise available space.
wheels running on rails. Products to be stored are placed in the
cradles and then easily moved in and out of the storage position.
Ideally suited to high volume movements of long loads, Rollrack can
achieve time savings of up to 80% over static rack
Rollrack makes light work of an otherwise difficult, cumbersome and
often dangerous task.
Rollrack’s ball-bearing mounted travelling cradle
has revolutionised the handling and storage of
rods, piping, beams and other long materials.
38
Storage arm height is adjustable in
76mm increments to accommodate
loads of almost any size.
39