official grain dockage sieves

OFFICIAL GRAIN DOCKAGE SIEVES
Seedburo Dockage Sieves are manufactured to comply with the specification of the U.S.
Department of Agriculture. They are regularly used by federal grain supervision offices, state
grain inspection departments and licensed grain inspectors. Most sieves are available in only
a commercial grade, with a few in precision grade. All federal grain inspectors use precision
sieves, but for most applications the commercial sieves will suffice. Sieves should be replaced
when the perforations show wear, to maintain accurate results. Slotted sieves used in sizing
rice, barley and oats need to be replaced regularly since these grains are highly abrasive. A
worn sieve lets too much material pass through, giving inaccurate results. Damaged or dented
sieves should always be replaced. Sieves are made on No. 20 gauge B & S aluminum. Decimal
equivalents of diameter or width are shown in parentheses. MADE IN USA
Actual Dims. ............................................................................................................................................................................ 13” Diam. x 2-3/8” Deep
For sieves A, N & H: ...................................................................................................................................................................... 13” Diam. x 2” Deep
For pan E: ...................................................................................................................................................................................... 13” Diam. x 3” Deep
COMMERCIAL
PRECISION
SIEVE SETS
CORN
Set of 2 sieves (A and Y) & E .................. No. 1 Set ..................... 1P set
WHEAT, RYE AND OATS
Set of 5 sieves (A, B, C, D, W) & E ........ No. 2D Set ................ 2DP set
Set of 5 sieves (A, B, C, F, W) & E ......... No. 2F Set ................. 2FP set
SOYBEAN
Set of two sieves (H and I) & E ............... No. 3 Set ..................... 3P set
COTTONSEED
No. A sieve & E pan ................................. No. 4 Set ..................... 4P set
BARLEY
Set of 2 sieves (B and L) & E ................. No. 5L Set ................. 5LP set
Set of 2 sieves (B and M) & E ................ No. 5M Set ................ 5MP set
FLAX
Set of 2 sieves (T and U) & E .................. No. 6 Set ........................ -CANOLA
Set of 5 sieves (R, S, T, V, Y) & E ............ No. 7 Set ........................ -RICE
Set of 3 sieves (X, Y, Z) & E .................... No. 8 Set ........................ -SORGHUM
Set of 2 sieves (K and B) & E .................. No. 9 Set ..................... 9P set
WEEVIL
No. C sieve & E bottom pan ................... No. 10 Set .................. 10P set
SUNFLOWER SEED (CONFECTIONERY)
Set of 3 sieves (A, B, J) & E ................... No. 11 Set .................. 11P set
SIEVE SETS
COMMERCIAL PRECISION
12/64” Round (0.1875”) scalper ................... No. A ..................... A-P
5/64” Triangle (0.0781”) ................................ No. B .................... B-P
1/12” Round (0.0833”) .................................. No. C .................... C-P
4.5/64” x 1/2” Oblong (0.0703”) .................... No. D ....................... -.064” x 3/8” Oblong (0.0640”)... ...................... -- ....................... F-P
9/64” Double SpacedTriangle (0.1406”) ....... No. G ....................... -10/64” x ¾” Oblong (0.1563”) scalper .......... No. H ....................... -8/64” Round (0.1250”) .................................. No. I ....................... I-P
10/64” Round (0.1563”) ................................ No. J ........................ -2.5/64” Round (0.0391”) ............................... No. K ....................... -5/64” x ¾” Slot (0.0781”) .................................. -- ........................... L
5.5/64” x ¾” Slot (0.0859”) ............................... -- .......................... M
10/64” Round Scalper (0.1563”) ................... No. N ....................... -6/64” x ¾” Slot (0.0938”) .................................. -- .......................... P
6.5/64” x ¾” Slot (0.1016”) ............................... -- .......................... Q
.028” x 15/32” Slot ........................................ No. R ....................... -.0395” x 15/32” Slot ...................................... No. S ........................ -3/64” x 3/8” oblong (0.0469”) ........................ No. T ........................ -4.5/64” Round (0.0703”) ............................... No. U ....................... -.035” x 15/32” Slot ........................................ No. V ........................ -5/64” Round (0.0781”) .................................. No. W ....................... -5.5/64” Round (0.0859”) ............................... No. X ........................ -6/64” Round (0.0938”) .................................. No. Y ........................ -6.5/64” Round (0.1016”) ............................... No. Z ........................ -Solid Bottom pan (for use with all sieves) .... No. E ......................... –
SPECIAL PERFORATION SIEVES
These are sieves with steel perforated discs spun into standard aluminum sides. We have listed a portion of the available popular sizes. Request
other sizes not listed. These dockage sieves are recommended for use with the Strand Sizer Shaker.
1/25” Rd ........................ No. 0022
1/24” Rd ........................ No. 0021
1/22” Rd ........................ No. 0019
1/21” Rd ........................ No. 0023
1/20” Rd ........................ No. 0020
1/18” Rd ........................ No. 0018
1/15” Rd ........................ No. 0015
1/14” Rd ........................ No. 0010
1/13” Rd ........................ No. 0005
4/64” Rd ........................ No. 0025
7/64” Rd ........................ No. 0035
7.5/64” Rd ..................... No. 0037
8.5/64” Rd ..................... No. 0031
9/64” Rd ........................ No. 0032
9.5 /64” Rd .................... No. 0038
10.5/64” Rd .................... No. 0039
11/64” Rd ...................... No. 0040
11.5/64” Rd ................... No. 0041
13/64” Rd ...................... No. 0043
14/64” Rd ...................... No. 0045
14.5/64” Rd ................... No. 0046
15/64” Rd ...................... No. 0050
16/64” Rd ...................... No. 0055
17/64” Rd ...................... No. 0060
17.5/64” Rd .................... No. 0062
18/64” Rd ...................... No. 0065
18.5 /64” Rd ................... No. 0066
19/64” Rd ...................... No. 0067
20/64” Rd ...................... No. 0070
21/64” Rd ...................... No. 0072
22/64” Rd ...................... No. 0075
23/64” Rd ...................... No. 0077
24/64” Rd ...................... No. 0080
25/64” Rd ...................... No. 0085
26/64” Rd ...................... No. 0090
27/64” Rd ...................... No. 0091
28/64” Rd ...................... No. 0095
30/64” Rd ...................... No. 0093
32/64” Rd ...................... No. 0092
34/64” Rd ...................... No. 0086
36/64” Rd ...................... No. 0081
40/64” Rd ...................... No. 0094
42/64” Rd ...................... No. 0084
48/64” Rd ...................... No. 0083
56/64” Rd ...................... No. 0096
4.5/64 x ¾” Oblong........ No. 0137
4-7/8 /64 x ¾” Oblong ... No. 0113
4/64 x ½” Oblong ......... No. 0109
5.5/64 x ¾” Oblong ...... No. 0104
6/64 x ¾” Oblong ......... No. 0088
6.5/64 x ¾” Oblong ...... No. 0099
1/22 x ½” Oblong ......... No. 0122
1/20 x ½” Oblong ......... No. 0128
1/18 x 1/4” Oblong ....... No. 0106
7/64” x ¾” Oblong ........ No. 0097
3/64 x 5/16” Oblong ..... No. 0121
8/64” x ¾” Oblong ........ No. 0100
7.5/64 x ¾” Oblong ...... No. 0098
8.5/64 x ¾” Oblong ....... No. 0114
9/64” x ¾” Oblong ........ No. 0105
9.5/64 x ¾” Oblong ...... No. 0107
10.5/64 x ¾” Oblong ..... No. 0108
11/64” x ¾” Oblong ....... No. 0110
11.5/64 x ¾” Oblong .......No. 0111
12/64” x ¾” Oblong ....... No. 0115
12.5/64 x ¾” Oblong ..... No. 0120
13/64 x ¾” Oblong ........ No. 0116
14/64 x ¾” Oblong ....... No. 0315
15/64 x ¾” Oblong ........ No. 0117
16/64 x ¾” Oblong ........ No. 0118
17/64 x ¾” Oblong ....... No. 0129
18/64 x ¾” Oblong ........ No. 0112
19/64 x ¾” Oblong ........ No. 0119
22/64 x ¾” Oblong ....... No. 0138
32/64 x ¾” Oblong ....... No. 0139
10/64” Tri.
(6/64 inscribed circle) ... No. 0102
11/64” Tri.
(6.5/64 inscribed circle... No. 0134
12/64” Tri.
(7/64 inscribed circle)..... No. 0103