n° 601-M - RAASM USA

Made in Italy
ED
FACTUR
D MANU
N
A
D
E
ITALY
DESIGN
ASM AT R A
n°
FLUID TRANSFER EQUIPMENT
601-M
INSTALLATION AND OPERATION
SIMPLE AND EFFECTIVE (1:1 RATIO)
2
4
1
3
The slide valve of the
air motor sends air (blue)
to the left chamber which,
pushing the membrane
outwards, compressing
the previously filled
liquid (green).
Through the effect of
the pressure created valve 1
closes and valve 2 opens
allowing the liquid to dispense
(green). The right membrane
then carries out the same
movement by the shaft joining
it to the left membrane, creating
a vacuum. Through the effect
of the vacuum, the valve 3
opens and the valve 4 closes,
enabling suction of the
liquid (orange).
2
4
1
3
The slide valve of the
air motor sends air (blue)
to the right chamber which,
pushing the membrane
outwards, compressing
the previously filled
liquid (green).
Through the effect of
the pressure created valve 3
closes and valve 4 opens
allowing the liquid to dispense
(green). The left membrane
then carries out the same
movement by the shaft joining
it to the right membrane, creating
a vacuum. Through the effect
of the vacuum, the valve 1
opens and the valve 2 closes,
enabling suction of the
liquid (orange).
HOW TO INSTALL THE PUMP
PUMP INSTALLED ON DRUM
TOP FEED
PUMP INSTALLED ON A MOBILE UNIT
(it is necessary to check the chemical
compatibility between pump material and liquid)
SUBMERGED PUMP
BOTTON FEED
BULK TANK
PUMP CONFIGURATION
Exploded view of the pump, showing
its main parts and thereby facilitating
the choice for a custom configuration.
The table summarises the pump
configurations available, allowing the
user to create his own personalised
code whenever the models listed on
the leaflet do not meet the specific
requirements.
MOTOR
INNER FLANGES
PARTS IN
CONTACT WITH
THE FLUID
MEMBRANE
BALLS
PARTS IN
CONTACT WITH
THE FLUID
Two types of Atex certifications are available, for zone 2 or for zone 1,
depending on the materials making up the pump.
II 3GD T4 cIIB X (for zone 2)
II 2GD T4 cIIB X (for zone 1)
SEATS
The valve seats are to be coupled to the balls and must ensure correct
closing. Like the balls, they must be made from a material suitable
for the fluid they come into contact with.
They open and close the flow of liquid as a result of the
reciprocating movement of the follower plates.
The material they are made from must be compatible
with the fluid being pumped.
They can be threaded (NPT) or flanged, single,
multiple and modular.
Defines the
inside diameter
of the manifold.
This is the heart
of the pump,
responsible for
the reciprocating
movement
that create
the flow
of liquid.
MATERIALS
AND ATEX VERSIONS
MANIFOLD FOR
INLET AND OUTLET
2B = plastic for Zone 2
A/ = NPT threaded connection
3C = aluminium for Zone 1 C/ = mult. NPT threaded con.
D/ = connection with flange
F/ = multiple modular
connection with flange
G/ = dual inlet connection
FLOW
INSIDE
DIAMETER
They are the only elastic parts of the
pump, that suck and pump the liquid with
their movement. The material they are
made from must be selected in order to
obtain the correct chemical compatibility
with the liquid to be pumped.
These are all the rigid
parts such as external
flanges, manifolds
and sleeves which are
constantly in contact
with the liquid to be
pumped. Available
in various materials,
depending on the type
of liquid.
These are not in contact with the pumped
liquid, but only with
the compressed air
feeding the motor.
KIND OF MATERIALS
MOTOR
INNER
FLANGES
PARTS IN
CONTACT WITH
THE FLUID
16 = 1/2” 1 = nichel plat. 1 = nichel plat. 1 = nichel plated
aluminium
aluminium
aluminium
26 = 1”
30 = 1.1/4”
7 = polypropylene
40 = 1.1/2”
50 = 2”
MEMBRANE
BALLS
SEATS
E = EPDM
H = hytrel
N = NBR
S = santoprene
A = acetalic
H = hytrel
S = santoprene
T = PTFE
A = acetalic
H = hytrel
P = polypropylene
S = santoprene
1 = cylindrical
T = PTFE +
hytrel
acetalic
2 = cylindrical
with flange
H/ = dual inlet NPT
threaded connection
EXAMPLE 3C1/16111E A A
plat. 1 = nichel plat. 1 = nichel plated
3C = aluminium for Zone 1 A/ = NPT threaded connection 16 = 1/2” 1 = nichel
E = EPDM
aluminium
aluminium
aluminium
polypropylene
A = acetalic
A = acetalic
Diaphragm pumps R. 1:1
for transfer industrial fluids
compatible with the
materials of the pumps,
made from die-cast
aluminium or molding injected
Polypropylene, with high
quality components, they
ensure lasting and reliable
operation even in extreme
conditions.
1/2” - 16 gpm
1” - 45 gpm
1/2” - 18.5 gpm
1” - 45 gpm
1.1/4” - 52.5 gpm
1.1/2” - 126.5 gpm
2” - 161 gpm
2” - 153 gpm
2” F
MODULAR WITH FLANGE 2”
2.1/2” F
MODULAR WITH FLANGE 2”
1.1/2” F
WITH FLANGE 1”
1/2” F
1.1/4” F
WITH FLANGE 1”
1” F
1/2” F
1/2” F
DESIGN
Note: The max flow rate
shown in the below graphics
has been obtained by
laboratory test.
3/4” F
Series
membrane
Balls for inlet and outlet
TESTING
in
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel ***
1” F
3/4” F
120-PB
Polypropylene - motor Aluminium
P/N 2BC/16117EA1-55
membrane
”
P/N 2BC/16117NH2-55
”
P/N 2BC/16117SS2-55
”
P/N 2BC/16117TT2-55
”
P/N 2BC/16117HH2-55
Max. pressure
Max cycles per min
*
Gal per cycle
Max suction lift
Max size pumpable solids
Max working temperature
Noise level **
Max air consumption (m3/min)
Air working pressure
Air inlet connection
Air outlet connection (muffler)
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel
in
3/4” F
120-PB
Polypropylene - motor Aluminium
P/N 2BH/16117EA1-55
P/N 2BH/16117HH2-55
P/N 2BH/16117NH2-55
P/N 2BH/16117SS2-55
P/N 2BH/16117TT2-55
membrane
”
”
”
”
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel
120 psi
330 cpm
0.05 gal
dry column 15’ - wet column 25’
0.06”
149° F
75 dB
18 cfm
30 - 90 psi
F 3/8” NPT
F 1/2” G
120 psi
330 cpm
0.05 gal
dry column 15’ - wet column 25’
0.06”
149° F
75 dB
18 cfm
30 - 90 psi
F 3/8” NPT
F 1/2” G
Fluid inlet connection
F 3/4” NPT (F 1” NPT for drum)
dual inlet F 3/4” NPT
Fluid outlet connection
F 1/2” NPT
F 1/2” NPT
WITH FLANGE 1”
in
1000-PB
Polypropylene - motor Aluminium
P/N 2BD/26117EAA-55
P/N 2BD/26117HHH-55
P/N 2BD/26117NHH-55
P/N 2BD/26117SSS-55
P/N 2BD/26117TTP-55
3/4” F
WITH FLANGE 1”
membrane
”
”
”
”
in
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel
120 psi
300 cpm
0.15 gal
dry column 16.4’ - wet column 25’
0.12”
149° F
75 dB
57 cfm
30 - 90 psi
F 3/8” NPT
F 1/2” G
ANSI 150 - DIN PN 10 - JIS 10K 1” (25 mm)
proneness to 1.1/4” thread
ANSI 150 - DIN PN 10 - JIS 10K 1” (25 mm)
proneness to 1.1/4” thread
1000-PB
120-AB
Polypropylene - motor Aluminium
P/N 2BG/26117EAA-55
P/N 2BG/26117HHH-55
P/N 2BG/26117NHH-55
P/N 2BG/26117SSS-55
P/N 2BG/26117TTP-55
membrane
”
”
”
”
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel
1.1/4” F
1000-AB
all Aluminium
P/N 3CA/16111EAA-55
P/N 3CA/16111HHH-55
P/N 3CA/16111NHH-55
P/N 3CA/16111SSS-55
P/N 3CA/16111TTP-55
120 psi
300 cpm
0.15 gal
dry column 16.4’ - wet column 25’
0.12”
149° F
75 dB
57 cfm
30 - 90 psi
F 3/8” NPT
F 1/2” G
dual inlet ANSI 150 - DIN PN 10 - JIS 10K 1” (25 mm)
proneness to 1.1/4” thread
ANSI 150 - DIN PN 10 - JIS 10K 1” (25 mm)
proneness to 1.1/4” thread
1.1/4” F
1140-AB
all Aluminium
membrane
”
”
”
”
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel
P/N 3CA/26111EAA-55
P/N 3CA/26111HHH-55
P/N 3CA/26111NHH-55
P/N 3CA/26111SSS-55
P/N 3CA/26111TTP-55
2” F
1120-AB
all Aluminium
membrane
”
”
”
”
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel
P/N 3CA/30111EAA-55
P/N 3CA/30111HHH-55
P/N 3CA/30111NHH-55
P/N 3CA/30111SSS-55
P/N 3CA/30111TTP-55
2000-AB
all Aluminium
membrane
”
”
”
”
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel
2000-AB
all Aluminium
P/N 3CA/40111EAA-55
membrane
”
P/N 3CA/40111NHH-55
”
P/N 3CA/40111SSS-55
”
P/N 3CA/40111TTP-55
”
P/N 3CA/40111HHH-55
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel
all Aluminium
P/N 3CA/50111EAA-55
membrane
”
P/N 3CA/50111NHH-55
”
P/N 3CA/50111SSS-55
”
P/N 3CA/50111TTP-55
”
P/N 3CA/50111HHH-55
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel
P/N 3CF/50111EAA-55
P/N 3CF/50111HHH-55
P/N 3CF/50111NHH-55
P/N 3CF/50111SSS-55
P/N 3CF/50111TTP-55
membrane
”
”
”
”
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel
120 psi
400 cpm
0.05 gal
dry column 15’ - wet column 25’
0.06”
212° F
75 dB
21 cfm
30 - 90 psi
F 3/8” NPT
F 1/2” G
120 psi
300 cpm
0.15 gal
dry column 15’ - wet column 25’
0.12”
212° F
75 dB
57 cfm
30 - 90 psi
F 3/8” NPT
F 1/2” G
120 psi
260 cpm
0.21 gal
dry column 16.4’ - wet column 25’
0.12”
212° F
75 dB
64 cfm
30 - 90 psi
F 3/4” NPT
F 1” G
120 psi
220 cpm
0.57 gal
dry column 16.4’ - wet column 25’
0.22”
212° F
78 dB
120 cfm
30 - 90 psi
F 3/4” NPT
F 1” G
120 psi
147 cpm
1.1 gal
dry column 16.4’ - wet column 25’
0.26”
212° F
82 dB
141 cfm
30 - 90 psi
F 3/4” NPT
F 1” G
120 psi
147 cpm
1.05 gal
dry column 16.4’ - wet column 25’
0.12”
212° F
82 dB
141 cfm
30 - 90 psi
F 3/4” NPT
F 1” G
F 3/4” NPT
F 1.1/4” NPT
F 1.1/4” NPT
F 2” NPT
F 2.1/2” NPT
ANSI 150 - DIN PN 10 - JIS 10K 2” (50 mm)
F 1/2” NPT
F 1” NPT
F 1.1/4” NPT
F 1.1/2” NPT
F 2” NPT
ANSI 150 - DIN PN 10 - JIS 10K 2” (50 mm)
Balls for inlet
and outlet
ASSEMBLY
A
0
15
(4)
30
(8)
45
(12)
60
(16)
KIND OF FLUID: Water 68 °F
SAE30 oil: (ISO VG 100) 68 °F
m3/min
A
B
1,6
(56)
1,2
(42)
0,8
(28)
C
0,4
(14)
0
45
(12)
90
(24)
135
(36)
bar
(psi) 300 (cfm)
225
2
(29)
0
l/min
gpm
lb 110
180
(48)
KIND OF FLUID: Water 68 °F
SAE30 oil: (ISO VG 100) 68 °F
m3/min
cycles/min
105
8
(116)
A
6
(87)
B
4
(58)
C
210
420 (cfm)
0,65
A
(23)
315
0,49
(17.2)
B
0,32
(11.5)
C
2
(29)
0
l/min
gpm
0,16
(5.75)
0
20
(5.4)
40
(10.7)
60
(16)
80
(21)
KIND OF FLUID: Water 68 °F
SAE30 oil: (ISO VG 100) 68 °F
bar
(psi) m3/min
cycles/min
75
8
(116)
A
6
(87)
B
4
(58)
C
150
A
B
1,6
(56)
1,2
(42)
0,8
(28)
C
2
(29)
0
l/min
gpm
0,4
(14)
0
45
(12)
90
(24)
135
(36)
bar
(psi) 300 (cfm)
225
180
(48)
KIND OF FLUID: Water 68 °F
SAE30 oil: (ISO VG 100) 68 °F
m3/min
cycles/min
65
8
(116)
A
6
(87)
B
4
(58)
C
130
1,8
(64)
A
B
1,35
(48)
0,9
(32)
C
2
(29)
0
l/min
gpm
0,45
(16)
0
50
(13)
100
(26)
150
(40)
bar
(psi) 260 (cfm)
195
200
(52)
KIND OF FLUID: Water 68 °F
SAE30 oil: (ISO VG 100) 68 °F
m3/min
cycles/min
55
8
(116)
A
6
(87)
B
4
(58)
C
110
A
B
3,4
(120)
2,55
(90)
1,7
(60)
C
2
(29)
0
l/min
gpm
0,85
(30)
0
120
(32)
240
(64)
360
(96)
bar
(psi) 220 (cfm)
165
480
(128)
KIND OF FLUID: Water 68 °F
m3/min
cycles/min
38
8
(116)
A
6
(87)
B
4
(58)
C
75
4
(140)
A
B
3
(105)
2
(70)
C
2
(29)
0
l/min
gpm
1
(35)
0
155
(41.5)
310
(83)
465
(125)
bar
(psi) 150 (cfm)
113
620
(166)
KIND OF FLUID: Water 68 °F
m3/min
cycles/min
38
75
150 (cfm)
113
8
(116)
A
A
4
(140)
6
(87)
B
B
3
(105)
4
(58)
C
2
(70)
C
2
(29)
0
l/min
gpm
1
(35)
0
150
(40)
300
(80)
450
(120)
600
(160)
KIND OF FLUID: Water 68 °F
AIR CONSUMPTION
C
N° 1 packing cf 5.6
FLUID OUTLET PRESSURE
0,13
(4.7)
4
(58)
lb 95
AIR CONSUMPTION
2
(29)
0
l/min
gpm
B
0,27
(9.5)
C
B
16.1” x 17” x 28”
N° 1 packing cf 5.6
FLUID OUTLET PRESSURE
C
6
(87)
18.2” x 17” x 24.2”
lb 56
AIR CONSUMPTION
4
(58)
0,4
(14.2)
N° 1 packing cf 2.3
FLUID OUTLET PRESSURE
4 bar (58 psi)
B
13.8” x 15.8” x 20.2”
lb 42
AIR CONSUMPTION
C
B
N° 1 packing cf 1.35
FLUID OUTLET PRESSURE
C
6
(87)
A
11.3” x 9.4” x 15.2”
lb 30
AIR CONSUMPTION
6 bar (87 psi)
8
(116)
150
N° 1 packing cf 0.9
*** With PTFE membrane flow rate is 10 % lower
cycles/min
75
10.3” x 7.9” x 13.6”
lb 17.6
FLUID OUTLET PRESSURE
B
A
340 (cfm)
0,53
A
(19)
N° 1 packing cf 0.5
AIR CONSUMPTION
B
8
(116)
255
7.9” x 6.3” x 10”
lb 26.5
FLUID OUTLET PRESSURE
8 bar (116 psi)
170
bar
(psi) m3/min
cycles/min
85
FLUID OUTLET PRESSURE
A
FLUID OUTLET PRESSURE
C
A
bar
(psi) AIR CONSUMPTION
PUMP AIR
FEEDING PRESSURE
14” x 7.8” x 16.5”
N° 1 packing cf 0.9
AIR CONSUMPTION
Overall dimensions (A x B x C)
8.6” x 7” x 12.8”
8.6” x 7” x 12.8”
11.8” x 7.9” x 17.9”
Packing - Weight
N° 1 packing cf 0.9
lb 26
N° 1 packing cf 0.5
lb 15.4
N° 1 packing cf 0.5
lb 15.4
** Different kind of muffler are available on request for special use or hard work
* Displacement per cycle may be influenced by suction lift, fluid viscosity, air pressure, number of cycles per minute
Diaphragm pumps R. 1:1
for transfer industrial fluids
compatible with the
materials of the pumps,
made from die-cast
aluminium or molding injected
Polypropylene, with high
quality components, they
ensure lasting and reliable
operation even in extreme
conditions.
1/2” - 16 gpm
1” - 45 gpm
1/2” - 18.5 gpm
1” - 45 gpm
1.1/4” - 52.5 gpm
1.1/2” - 126.5 gpm
2” - 161 gpm
2” - 153 gpm
2” F
MODULAR WITH FLANGE 2”
2.1/2” F
MODULAR WITH FLANGE 2”
1.1/2” F
WITH FLANGE 1”
1/2” F
1.1/4” F
WITH FLANGE 1”
1” F
1/2” F
1/2” F
DESIGN
Note: The max flow rate
shown in the below graphics
has been obtained by
laboratory test.
3/4” F
Series
membrane
Balls for inlet and outlet
TESTING
in
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel ***
1” F
3/4” F
120-PB
Polypropylene - motor Aluminium
P/N 2BC/16117EA1-55
membrane
”
P/N 2BC/16117NH2-55
”
P/N 2BC/16117SS2-55
”
P/N 2BC/16117TT2-55
”
P/N 2BC/16117HH2-55
Max. pressure
Max cycles per min
*
Gal per cycle
Max suction lift
Max size pumpable solids
Max working temperature
Noise level **
Max air consumption (m3/min)
Air working pressure
Air inlet connection
Air outlet connection (muffler)
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel
in
3/4” F
120-PB
Polypropylene - motor Aluminium
P/N 2BH/16117EA1-55
P/N 2BH/16117HH2-55
P/N 2BH/16117NH2-55
P/N 2BH/16117SS2-55
P/N 2BH/16117TT2-55
membrane
”
”
”
”
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel
120 psi
330 cpm
0.05 gal
dry column 15’ - wet column 25’
0.06”
149° F
75 dB
18 cfm
30 - 90 psi
F 3/8” NPT
F 1/2” G
120 psi
330 cpm
0.05 gal
dry column 15’ - wet column 25’
0.06”
149° F
75 dB
18 cfm
30 - 90 psi
F 3/8” NPT
F 1/2” G
Fluid inlet connection
F 3/4” NPT (F 1” NPT for drum)
dual inlet F 3/4” NPT
Fluid outlet connection
F 1/2” NPT
F 1/2” NPT
WITH FLANGE 1”
in
1000-PB
Polypropylene - motor Aluminium
P/N 2BD/26117EAA-55
P/N 2BD/26117HHH-55
P/N 2BD/26117NHH-55
P/N 2BD/26117SSS-55
P/N 2BD/26117TTP-55
3/4” F
WITH FLANGE 1”
membrane
”
”
”
”
in
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel
120 psi
300 cpm
0.15 gal
dry column 16.4’ - wet column 25’
0.12”
149° F
75 dB
57 cfm
30 - 90 psi
F 3/8” NPT
F 1/2” G
ANSI 150 - DIN PN 10 - JIS 10K 1” (25 mm)
proneness to 1.1/4” thread
ANSI 150 - DIN PN 10 - JIS 10K 1” (25 mm)
proneness to 1.1/4” thread
1000-PB
120-AB
Polypropylene - motor Aluminium
P/N 2BG/26117EAA-55
P/N 2BG/26117HHH-55
P/N 2BG/26117NHH-55
P/N 2BG/26117SSS-55
P/N 2BG/26117TTP-55
membrane
”
”
”
”
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel
1.1/4” F
1000-AB
all Aluminium
P/N 3CA/16111EAA-55
P/N 3CA/16111HHH-55
P/N 3CA/16111NHH-55
P/N 3CA/16111SSS-55
P/N 3CA/16111TTP-55
120 psi
300 cpm
0.15 gal
dry column 16.4’ - wet column 25’
0.12”
149° F
75 dB
57 cfm
30 - 90 psi
F 3/8” NPT
F 1/2” G
dual inlet ANSI 150 - DIN PN 10 - JIS 10K 1” (25 mm)
proneness to 1.1/4” thread
ANSI 150 - DIN PN 10 - JIS 10K 1” (25 mm)
proneness to 1.1/4” thread
1.1/4” F
1140-AB
all Aluminium
membrane
”
”
”
”
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel
P/N 3CA/26111EAA-55
P/N 3CA/26111HHH-55
P/N 3CA/26111NHH-55
P/N 3CA/26111SSS-55
P/N 3CA/26111TTP-55
2” F
1120-AB
all Aluminium
membrane
”
”
”
”
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel
P/N 3CA/30111EAA-55
P/N 3CA/30111HHH-55
P/N 3CA/30111NHH-55
P/N 3CA/30111SSS-55
P/N 3CA/30111TTP-55
2000-AB
all Aluminium
membrane
”
”
”
”
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel
2000-AB
all Aluminium
P/N 3CA/40111EAA-55
membrane
”
P/N 3CA/40111NHH-55
”
P/N 3CA/40111SSS-55
”
P/N 3CA/40111TTP-55
”
P/N 3CA/40111HHH-55
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel
all Aluminium
P/N 3CA/50111EAA-55
membrane
”
P/N 3CA/50111NHH-55
”
P/N 3CA/50111SSS-55
”
P/N 3CA/50111TTP-55
”
P/N 3CA/50111HHH-55
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel
P/N 3CF/50111EAA-55
P/N 3CF/50111HHH-55
P/N 3CF/50111NHH-55
P/N 3CF/50111SSS-55
P/N 3CF/50111TTP-55
membrane
”
”
”
”
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel
120 psi
400 cpm
0.05 gal
dry column 15’ - wet column 25’
0.06”
212° F
75 dB
21 cfm
30 - 90 psi
F 3/8” NPT
F 1/2” G
120 psi
300 cpm
0.15 gal
dry column 15’ - wet column 25’
0.12”
212° F
75 dB
57 cfm
30 - 90 psi
F 3/8” NPT
F 1/2” G
120 psi
260 cpm
0.21 gal
dry column 16.4’ - wet column 25’
0.12”
212° F
75 dB
64 cfm
30 - 90 psi
F 3/4” NPT
F 1” G
120 psi
220 cpm
0.57 gal
dry column 16.4’ - wet column 25’
0.22”
212° F
78 dB
120 cfm
30 - 90 psi
F 3/4” NPT
F 1” G
120 psi
147 cpm
1.1 gal
dry column 16.4’ - wet column 25’
0.26”
212° F
82 dB
141 cfm
30 - 90 psi
F 3/4” NPT
F 1” G
120 psi
147 cpm
1.05 gal
dry column 16.4’ - wet column 25’
0.12”
212° F
82 dB
141 cfm
30 - 90 psi
F 3/4” NPT
F 1” G
F 3/4” NPT
F 1.1/4” NPT
F 1.1/4” NPT
F 2” NPT
F 2.1/2” NPT
ANSI 150 - DIN PN 10 - JIS 10K 2” (50 mm)
F 1/2” NPT
F 1” NPT
F 1.1/4” NPT
F 1.1/2” NPT
F 2” NPT
ANSI 150 - DIN PN 10 - JIS 10K 2” (50 mm)
Balls for inlet
and outlet
ASSEMBLY
A
0
15
(4)
30
(8)
45
(12)
60
(16)
KIND OF FLUID: Water 68 °F
SAE30 oil: (ISO VG 100) 68 °F
m3/min
A
B
1,6
(56)
1,2
(42)
0,8
(28)
C
0,4
(14)
0
45
(12)
90
(24)
135
(36)
bar
(psi) 300 (cfm)
225
2
(29)
0
l/min
gpm
lb 110
180
(48)
KIND OF FLUID: Water 68 °F
SAE30 oil: (ISO VG 100) 68 °F
m3/min
cycles/min
105
8
(116)
A
6
(87)
B
4
(58)
C
210
420 (cfm)
0,65
A
(23)
315
0,49
(17.2)
B
0,32
(11.5)
C
2
(29)
0
l/min
gpm
0,16
(5.75)
0
20
(5.4)
40
(10.7)
60
(16)
80
(21)
KIND OF FLUID: Water 68 °F
SAE30 oil: (ISO VG 100) 68 °F
bar
(psi) m3/min
cycles/min
75
8
(116)
A
6
(87)
B
4
(58)
C
150
A
B
1,6
(56)
1,2
(42)
0,8
(28)
C
2
(29)
0
l/min
gpm
0,4
(14)
0
45
(12)
90
(24)
135
(36)
bar
(psi) 300 (cfm)
225
180
(48)
KIND OF FLUID: Water 68 °F
SAE30 oil: (ISO VG 100) 68 °F
m3/min
cycles/min
65
8
(116)
A
6
(87)
B
4
(58)
C
130
1,8
(64)
A
B
1,35
(48)
0,9
(32)
C
2
(29)
0
l/min
gpm
0,45
(16)
0
50
(13)
100
(26)
150
(40)
bar
(psi) 260 (cfm)
195
200
(52)
KIND OF FLUID: Water 68 °F
SAE30 oil: (ISO VG 100) 68 °F
m3/min
cycles/min
55
8
(116)
A
6
(87)
B
4
(58)
C
110
A
B
3,4
(120)
2,55
(90)
1,7
(60)
C
2
(29)
0
l/min
gpm
0,85
(30)
0
120
(32)
240
(64)
360
(96)
bar
(psi) 220 (cfm)
165
480
(128)
KIND OF FLUID: Water 68 °F
m3/min
cycles/min
38
8
(116)
A
6
(87)
B
4
(58)
C
75
4
(140)
A
B
3
(105)
2
(70)
C
2
(29)
0
l/min
gpm
1
(35)
0
155
(41.5)
310
(83)
465
(125)
bar
(psi) 150 (cfm)
113
620
(166)
KIND OF FLUID: Water 68 °F
m3/min
cycles/min
38
75
150 (cfm)
113
8
(116)
A
A
4
(140)
6
(87)
B
B
3
(105)
4
(58)
C
2
(70)
C
2
(29)
0
l/min
gpm
1
(35)
0
150
(40)
300
(80)
450
(120)
600
(160)
KIND OF FLUID: Water 68 °F
AIR CONSUMPTION
C
N° 1 packing cf 5.6
FLUID OUTLET PRESSURE
0,13
(4.7)
4
(58)
lb 95
AIR CONSUMPTION
2
(29)
0
l/min
gpm
B
0,27
(9.5)
C
B
16.1” x 17” x 28”
N° 1 packing cf 5.6
FLUID OUTLET PRESSURE
C
6
(87)
18.2” x 17” x 24.2”
lb 56
AIR CONSUMPTION
4
(58)
0,4
(14.2)
N° 1 packing cf 2.3
FLUID OUTLET PRESSURE
4 bar (58 psi)
B
13.8” x 15.8” x 20.2”
lb 42
AIR CONSUMPTION
C
B
N° 1 packing cf 1.35
FLUID OUTLET PRESSURE
C
6
(87)
A
11.3” x 9.4” x 15.2”
lb 30
AIR CONSUMPTION
6 bar (87 psi)
8
(116)
150
N° 1 packing cf 0.9
*** With PTFE membrane flow rate is 10 % lower
cycles/min
75
10.3” x 7.9” x 13.6”
lb 17.6
FLUID OUTLET PRESSURE
B
A
340 (cfm)
0,53
A
(19)
N° 1 packing cf 0.5
AIR CONSUMPTION
B
8
(116)
255
7.9” x 6.3” x 10”
lb 26.5
FLUID OUTLET PRESSURE
8 bar (116 psi)
170
bar
(psi) m3/min
cycles/min
85
FLUID OUTLET PRESSURE
A
FLUID OUTLET PRESSURE
C
A
bar
(psi) AIR CONSUMPTION
PUMP AIR
FEEDING PRESSURE
14” x 7.8” x 16.5”
N° 1 packing cf 0.9
AIR CONSUMPTION
Overall dimensions (A x B x C)
8.6” x 7” x 12.8”
8.6” x 7” x 12.8”
11.8” x 7.9” x 17.9”
Packing - Weight
N° 1 packing cf 0.9
lb 26
N° 1 packing cf 0.5
lb 15.4
N° 1 packing cf 0.5
lb 15.4
** Different kind of muffler are available on request for special use or hard work
* Displacement per cycle may be influenced by suction lift, fluid viscosity, air pressure, number of cycles per minute
Diaphragm pumps R. 1:1
for transfer industrial fluids
compatible with the
materials of the pumps,
made from die-cast
aluminium or molding injected
Polypropylene, with high
quality components, they
ensure lasting and reliable
operation even in extreme
conditions.
1/2” - 16 gpm
1” - 45 gpm
1/2” - 18.5 gpm
1” - 45 gpm
1.1/4” - 52.5 gpm
1.1/2” - 126.5 gpm
2” - 161 gpm
2” - 153 gpm
2” F
MODULAR WITH FLANGE 2”
2.1/2” F
MODULAR WITH FLANGE 2”
1.1/2” F
WITH FLANGE 1”
1/2” F
1.1/4” F
WITH FLANGE 1”
1” F
1/2” F
1/2” F
DESIGN
Note: The max flow rate
shown in the below graphics
has been obtained by
laboratory test.
3/4” F
Series
membrane
Balls for inlet and outlet
TESTING
in
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel ***
1” F
3/4” F
120-PB
Polypropylene - motor Aluminium
P/N 2BC/16117EA1-55
membrane
”
P/N 2BC/16117NH2-55
”
P/N 2BC/16117SS2-55
”
P/N 2BC/16117TT2-55
”
P/N 2BC/16117HH2-55
Max. pressure
Max cycles per min
*
Gal per cycle
Max suction lift
Max size pumpable solids
Max working temperature
Noise level **
Max air consumption (m3/min)
Air working pressure
Air inlet connection
Air outlet connection (muffler)
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel
in
3/4” F
120-PB
Polypropylene - motor Aluminium
P/N 2BH/16117EA1-55
P/N 2BH/16117HH2-55
P/N 2BH/16117NH2-55
P/N 2BH/16117SS2-55
P/N 2BH/16117TT2-55
membrane
”
”
”
”
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel
120 psi
330 cpm
0.05 gal
dry column 15’ - wet column 25’
0.06”
149° F
75 dB
18 cfm
30 - 90 psi
F 3/8” NPT
F 1/2” G
120 psi
330 cpm
0.05 gal
dry column 15’ - wet column 25’
0.06”
149° F
75 dB
18 cfm
30 - 90 psi
F 3/8” NPT
F 1/2” G
Fluid inlet connection
F 3/4” NPT (F 1” NPT for drum)
dual inlet F 3/4” NPT
Fluid outlet connection
F 1/2” NPT
F 1/2” NPT
WITH FLANGE 1”
in
1000-PB
Polypropylene - motor Aluminium
P/N 2BD/26117EAA-55
P/N 2BD/26117HHH-55
P/N 2BD/26117NHH-55
P/N 2BD/26117SSS-55
P/N 2BD/26117TTP-55
3/4” F
WITH FLANGE 1”
membrane
”
”
”
”
in
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel
120 psi
300 cpm
0.15 gal
dry column 16.4’ - wet column 25’
0.12”
149° F
75 dB
57 cfm
30 - 90 psi
F 3/8” NPT
F 1/2” G
ANSI 150 - DIN PN 10 - JIS 10K 1” (25 mm)
proneness to 1.1/4” thread
ANSI 150 - DIN PN 10 - JIS 10K 1” (25 mm)
proneness to 1.1/4” thread
1000-PB
120-AB
Polypropylene - motor Aluminium
P/N 2BG/26117EAA-55
P/N 2BG/26117HHH-55
P/N 2BG/26117NHH-55
P/N 2BG/26117SSS-55
P/N 2BG/26117TTP-55
membrane
”
”
”
”
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel
1.1/4” F
1000-AB
all Aluminium
P/N 3CA/16111EAA-55
P/N 3CA/16111HHH-55
P/N 3CA/16111NHH-55
P/N 3CA/16111SSS-55
P/N 3CA/16111TTP-55
120 psi
300 cpm
0.15 gal
dry column 16.4’ - wet column 25’
0.12”
149° F
75 dB
57 cfm
30 - 90 psi
F 3/8” NPT
F 1/2” G
dual inlet ANSI 150 - DIN PN 10 - JIS 10K 1” (25 mm)
proneness to 1.1/4” thread
ANSI 150 - DIN PN 10 - JIS 10K 1” (25 mm)
proneness to 1.1/4” thread
1.1/4” F
1140-AB
all Aluminium
membrane
”
”
”
”
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel
P/N 3CA/26111EAA-55
P/N 3CA/26111HHH-55
P/N 3CA/26111NHH-55
P/N 3CA/26111SSS-55
P/N 3CA/26111TTP-55
2” F
1120-AB
all Aluminium
membrane
”
”
”
”
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel
P/N 3CA/30111EAA-55
P/N 3CA/30111HHH-55
P/N 3CA/30111NHH-55
P/N 3CA/30111SSS-55
P/N 3CA/30111TTP-55
2000-AB
all Aluminium
membrane
”
”
”
”
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel
2000-AB
all Aluminium
P/N 3CA/40111EAA-55
membrane
”
P/N 3CA/40111NHH-55
”
P/N 3CA/40111SSS-55
”
P/N 3CA/40111TTP-55
”
P/N 3CA/40111HHH-55
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel
all Aluminium
P/N 3CA/50111EAA-55
membrane
”
P/N 3CA/50111NHH-55
”
P/N 3CA/50111SSS-55
”
P/N 3CA/50111TTP-55
”
P/N 3CA/50111HHH-55
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel
P/N 3CF/50111EAA-55
P/N 3CF/50111HHH-55
P/N 3CF/50111NHH-55
P/N 3CF/50111SSS-55
P/N 3CF/50111TTP-55
membrane
”
”
”
”
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel
120 psi
400 cpm
0.05 gal
dry column 15’ - wet column 25’
0.06”
212° F
75 dB
21 cfm
30 - 90 psi
F 3/8” NPT
F 1/2” G
120 psi
300 cpm
0.15 gal
dry column 15’ - wet column 25’
0.12”
212° F
75 dB
57 cfm
30 - 90 psi
F 3/8” NPT
F 1/2” G
120 psi
260 cpm
0.21 gal
dry column 16.4’ - wet column 25’
0.12”
212° F
75 dB
64 cfm
30 - 90 psi
F 3/4” NPT
F 1” G
120 psi
220 cpm
0.57 gal
dry column 16.4’ - wet column 25’
0.22”
212° F
78 dB
120 cfm
30 - 90 psi
F 3/4” NPT
F 1” G
120 psi
147 cpm
1.1 gal
dry column 16.4’ - wet column 25’
0.26”
212° F
82 dB
141 cfm
30 - 90 psi
F 3/4” NPT
F 1” G
120 psi
147 cpm
1.05 gal
dry column 16.4’ - wet column 25’
0.12”
212° F
82 dB
141 cfm
30 - 90 psi
F 3/4” NPT
F 1” G
F 3/4” NPT
F 1.1/4” NPT
F 1.1/4” NPT
F 2” NPT
F 2.1/2” NPT
ANSI 150 - DIN PN 10 - JIS 10K 2” (50 mm)
F 1/2” NPT
F 1” NPT
F 1.1/4” NPT
F 1.1/2” NPT
F 2” NPT
ANSI 150 - DIN PN 10 - JIS 10K 2” (50 mm)
Balls for inlet
and outlet
ASSEMBLY
A
0
15
(4)
30
(8)
45
(12)
60
(16)
KIND OF FLUID: Water 68 °F
SAE30 oil: (ISO VG 100) 68 °F
m3/min
A
B
1,6
(56)
1,2
(42)
0,8
(28)
C
0,4
(14)
0
45
(12)
90
(24)
135
(36)
bar
(psi) 300 (cfm)
225
2
(29)
0
l/min
gpm
lb 110
180
(48)
KIND OF FLUID: Water 68 °F
SAE30 oil: (ISO VG 100) 68 °F
m3/min
cycles/min
105
8
(116)
A
6
(87)
B
4
(58)
C
210
420 (cfm)
0,65
A
(23)
315
0,49
(17.2)
B
0,32
(11.5)
C
2
(29)
0
l/min
gpm
0,16
(5.75)
0
20
(5.4)
40
(10.7)
60
(16)
80
(21)
KIND OF FLUID: Water 68 °F
SAE30 oil: (ISO VG 100) 68 °F
bar
(psi) m3/min
cycles/min
75
8
(116)
A
6
(87)
B
4
(58)
C
150
A
B
1,6
(56)
1,2
(42)
0,8
(28)
C
2
(29)
0
l/min
gpm
0,4
(14)
0
45
(12)
90
(24)
135
(36)
bar
(psi) 300 (cfm)
225
180
(48)
KIND OF FLUID: Water 68 °F
SAE30 oil: (ISO VG 100) 68 °F
m3/min
cycles/min
65
8
(116)
A
6
(87)
B
4
(58)
C
130
1,8
(64)
A
B
1,35
(48)
0,9
(32)
C
2
(29)
0
l/min
gpm
0,45
(16)
0
50
(13)
100
(26)
150
(40)
bar
(psi) 260 (cfm)
195
200
(52)
KIND OF FLUID: Water 68 °F
SAE30 oil: (ISO VG 100) 68 °F
m3/min
cycles/min
55
8
(116)
A
6
(87)
B
4
(58)
C
110
A
B
3,4
(120)
2,55
(90)
1,7
(60)
C
2
(29)
0
l/min
gpm
0,85
(30)
0
120
(32)
240
(64)
360
(96)
bar
(psi) 220 (cfm)
165
480
(128)
KIND OF FLUID: Water 68 °F
m3/min
cycles/min
38
8
(116)
A
6
(87)
B
4
(58)
C
75
4
(140)
A
B
3
(105)
2
(70)
C
2
(29)
0
l/min
gpm
1
(35)
0
155
(41.5)
310
(83)
465
(125)
bar
(psi) 150 (cfm)
113
620
(166)
KIND OF FLUID: Water 68 °F
m3/min
cycles/min
38
75
150 (cfm)
113
8
(116)
A
A
4
(140)
6
(87)
B
B
3
(105)
4
(58)
C
2
(70)
C
2
(29)
0
l/min
gpm
1
(35)
0
150
(40)
300
(80)
450
(120)
600
(160)
KIND OF FLUID: Water 68 °F
AIR CONSUMPTION
C
N° 1 packing cf 5.6
FLUID OUTLET PRESSURE
0,13
(4.7)
4
(58)
lb 95
AIR CONSUMPTION
2
(29)
0
l/min
gpm
B
0,27
(9.5)
C
B
16.1” x 17” x 28”
N° 1 packing cf 5.6
FLUID OUTLET PRESSURE
C
6
(87)
18.2” x 17” x 24.2”
lb 56
AIR CONSUMPTION
4
(58)
0,4
(14.2)
N° 1 packing cf 2.3
FLUID OUTLET PRESSURE
4 bar (58 psi)
B
13.8” x 15.8” x 20.2”
lb 42
AIR CONSUMPTION
C
B
N° 1 packing cf 1.35
FLUID OUTLET PRESSURE
C
6
(87)
A
11.3” x 9.4” x 15.2”
lb 30
AIR CONSUMPTION
6 bar (87 psi)
8
(116)
150
N° 1 packing cf 0.9
*** With PTFE membrane flow rate is 10 % lower
cycles/min
75
10.3” x 7.9” x 13.6”
lb 17.6
FLUID OUTLET PRESSURE
B
A
340 (cfm)
0,53
A
(19)
N° 1 packing cf 0.5
AIR CONSUMPTION
B
8
(116)
255
7.9” x 6.3” x 10”
lb 26.5
FLUID OUTLET PRESSURE
8 bar (116 psi)
170
bar
(psi) m3/min
cycles/min
85
FLUID OUTLET PRESSURE
A
FLUID OUTLET PRESSURE
C
A
bar
(psi) AIR CONSUMPTION
PUMP AIR
FEEDING PRESSURE
14” x 7.8” x 16.5”
N° 1 packing cf 0.9
AIR CONSUMPTION
Overall dimensions (A x B x C)
8.6” x 7” x 12.8”
8.6” x 7” x 12.8”
11.8” x 7.9” x 17.9”
Packing - Weight
N° 1 packing cf 0.9
lb 26
N° 1 packing cf 0.5
lb 15.4
N° 1 packing cf 0.5
lb 15.4
** Different kind of muffler are available on request for special use or hard work
* Displacement per cycle may be influenced by suction lift, fluid viscosity, air pressure, number of cycles per minute
Diaphragm pumps R. 1:1
for transfer industrial fluids
compatible with the
materials of the pumps,
made from die-cast
aluminium or molding injected
Polypropylene, with high
quality components, they
ensure lasting and reliable
operation even in extreme
conditions.
1/2” - 16 gpm
1” - 45 gpm
1/2” - 18.5 gpm
1” - 45 gpm
1.1/4” - 52.5 gpm
1.1/2” - 126.5 gpm
2” - 161 gpm
2” - 153 gpm
2” F
MODULAR WITH FLANGE 2”
2.1/2” F
MODULAR WITH FLANGE 2”
1.1/2” F
WITH FLANGE 1”
1/2” F
1.1/4” F
WITH FLANGE 1”
1” F
1/2” F
1/2” F
DESIGN
Note: The max flow rate
shown in the below graphics
has been obtained by
laboratory test.
3/4” F
Series
membrane
Balls for inlet and outlet
TESTING
in
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel ***
1” F
3/4” F
120-PB
Polypropylene - motor Aluminium
P/N 2BC/16117EA1-55
membrane
”
P/N 2BC/16117NH2-55
”
P/N 2BC/16117SS2-55
”
P/N 2BC/16117TT2-55
”
P/N 2BC/16117HH2-55
Max. pressure
Max cycles per min
*
Gal per cycle
Max suction lift
Max size pumpable solids
Max working temperature
Noise level **
Max air consumption (m3/min)
Air working pressure
Air inlet connection
Air outlet connection (muffler)
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel
in
3/4” F
120-PB
Polypropylene - motor Aluminium
P/N 2BH/16117EA1-55
P/N 2BH/16117HH2-55
P/N 2BH/16117NH2-55
P/N 2BH/16117SS2-55
P/N 2BH/16117TT2-55
membrane
”
”
”
”
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel
120 psi
330 cpm
0.05 gal
dry column 15’ - wet column 25’
0.06”
149° F
75 dB
18 cfm
30 - 90 psi
F 3/8” NPT
F 1/2” G
120 psi
330 cpm
0.05 gal
dry column 15’ - wet column 25’
0.06”
149° F
75 dB
18 cfm
30 - 90 psi
F 3/8” NPT
F 1/2” G
Fluid inlet connection
F 3/4” NPT (F 1” NPT for drum)
dual inlet F 3/4” NPT
Fluid outlet connection
F 1/2” NPT
F 1/2” NPT
WITH FLANGE 1”
in
1000-PB
Polypropylene - motor Aluminium
P/N 2BD/26117EAA-55
P/N 2BD/26117HHH-55
P/N 2BD/26117NHH-55
P/N 2BD/26117SSS-55
P/N 2BD/26117TTP-55
3/4” F
WITH FLANGE 1”
membrane
”
”
”
”
in
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel
120 psi
300 cpm
0.15 gal
dry column 16.4’ - wet column 25’
0.12”
149° F
75 dB
57 cfm
30 - 90 psi
F 3/8” NPT
F 1/2” G
ANSI 150 - DIN PN 10 - JIS 10K 1” (25 mm)
proneness to 1.1/4” thread
ANSI 150 - DIN PN 10 - JIS 10K 1” (25 mm)
proneness to 1.1/4” thread
1000-PB
120-AB
Polypropylene - motor Aluminium
P/N 2BG/26117EAA-55
P/N 2BG/26117HHH-55
P/N 2BG/26117NHH-55
P/N 2BG/26117SSS-55
P/N 2BG/26117TTP-55
membrane
”
”
”
”
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel
1.1/4” F
1000-AB
all Aluminium
P/N 3CA/16111EAA-55
P/N 3CA/16111HHH-55
P/N 3CA/16111NHH-55
P/N 3CA/16111SSS-55
P/N 3CA/16111TTP-55
120 psi
300 cpm
0.15 gal
dry column 16.4’ - wet column 25’
0.12”
149° F
75 dB
57 cfm
30 - 90 psi
F 3/8” NPT
F 1/2” G
dual inlet ANSI 150 - DIN PN 10 - JIS 10K 1” (25 mm)
proneness to 1.1/4” thread
ANSI 150 - DIN PN 10 - JIS 10K 1” (25 mm)
proneness to 1.1/4” thread
1.1/4” F
1140-AB
all Aluminium
membrane
”
”
”
”
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel
P/N 3CA/26111EAA-55
P/N 3CA/26111HHH-55
P/N 3CA/26111NHH-55
P/N 3CA/26111SSS-55
P/N 3CA/26111TTP-55
2” F
1120-AB
all Aluminium
membrane
”
”
”
”
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel
P/N 3CA/30111EAA-55
P/N 3CA/30111HHH-55
P/N 3CA/30111NHH-55
P/N 3CA/30111SSS-55
P/N 3CA/30111TTP-55
2000-AB
all Aluminium
membrane
”
”
”
”
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel
2000-AB
all Aluminium
P/N 3CA/40111EAA-55
membrane
”
P/N 3CA/40111NHH-55
”
P/N 3CA/40111SSS-55
”
P/N 3CA/40111TTP-55
”
P/N 3CA/40111HHH-55
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel
all Aluminium
P/N 3CA/50111EAA-55
membrane
”
P/N 3CA/50111NHH-55
”
P/N 3CA/50111SSS-55
”
P/N 3CA/50111TTP-55
”
P/N 3CA/50111HHH-55
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel
P/N 3CF/50111EAA-55
P/N 3CF/50111HHH-55
P/N 3CF/50111NHH-55
P/N 3CF/50111SSS-55
P/N 3CF/50111TTP-55
membrane
”
”
”
”
EPDM
Hytrel
NBR
Santoprene
PTFE+Hytrel
120 psi
400 cpm
0.05 gal
dry column 15’ - wet column 25’
0.06”
212° F
75 dB
21 cfm
30 - 90 psi
F 3/8” NPT
F 1/2” G
120 psi
300 cpm
0.15 gal
dry column 15’ - wet column 25’
0.12”
212° F
75 dB
57 cfm
30 - 90 psi
F 3/8” NPT
F 1/2” G
120 psi
260 cpm
0.21 gal
dry column 16.4’ - wet column 25’
0.12”
212° F
75 dB
64 cfm
30 - 90 psi
F 3/4” NPT
F 1” G
120 psi
220 cpm
0.57 gal
dry column 16.4’ - wet column 25’
0.22”
212° F
78 dB
120 cfm
30 - 90 psi
F 3/4” NPT
F 1” G
120 psi
147 cpm
1.1 gal
dry column 16.4’ - wet column 25’
0.26”
212° F
82 dB
141 cfm
30 - 90 psi
F 3/4” NPT
F 1” G
120 psi
147 cpm
1.05 gal
dry column 16.4’ - wet column 25’
0.12”
212° F
82 dB
141 cfm
30 - 90 psi
F 3/4” NPT
F 1” G
F 3/4” NPT
F 1.1/4” NPT
F 1.1/4” NPT
F 2” NPT
F 2.1/2” NPT
ANSI 150 - DIN PN 10 - JIS 10K 2” (50 mm)
F 1/2” NPT
F 1” NPT
F 1.1/4” NPT
F 1.1/2” NPT
F 2” NPT
ANSI 150 - DIN PN 10 - JIS 10K 2” (50 mm)
Balls for inlet
and outlet
ASSEMBLY
A
0
15
(4)
30
(8)
45
(12)
60
(16)
KIND OF FLUID: Water 68 °F
SAE30 oil: (ISO VG 100) 68 °F
m3/min
A
B
1,6
(56)
1,2
(42)
0,8
(28)
C
0,4
(14)
0
45
(12)
90
(24)
135
(36)
bar
(psi) 300 (cfm)
225
2
(29)
0
l/min
gpm
lb 110
180
(48)
KIND OF FLUID: Water 68 °F
SAE30 oil: (ISO VG 100) 68 °F
m3/min
cycles/min
105
8
(116)
A
6
(87)
B
4
(58)
C
210
420 (cfm)
0,65
A
(23)
315
0,49
(17.2)
B
0,32
(11.5)
C
2
(29)
0
l/min
gpm
0,16
(5.75)
0
20
(5.4)
40
(10.7)
60
(16)
80
(21)
KIND OF FLUID: Water 68 °F
SAE30 oil: (ISO VG 100) 68 °F
bar
(psi) m3/min
cycles/min
75
8
(116)
A
6
(87)
B
4
(58)
C
150
A
B
1,6
(56)
1,2
(42)
0,8
(28)
C
2
(29)
0
l/min
gpm
0,4
(14)
0
45
(12)
90
(24)
135
(36)
bar
(psi) 300 (cfm)
225
180
(48)
KIND OF FLUID: Water 68 °F
SAE30 oil: (ISO VG 100) 68 °F
m3/min
cycles/min
65
8
(116)
A
6
(87)
B
4
(58)
C
130
1,8
(64)
A
B
1,35
(48)
0,9
(32)
C
2
(29)
0
l/min
gpm
0,45
(16)
0
50
(13)
100
(26)
150
(40)
bar
(psi) 260 (cfm)
195
200
(52)
KIND OF FLUID: Water 68 °F
SAE30 oil: (ISO VG 100) 68 °F
m3/min
cycles/min
55
8
(116)
A
6
(87)
B
4
(58)
C
110
A
B
3,4
(120)
2,55
(90)
1,7
(60)
C
2
(29)
0
l/min
gpm
0,85
(30)
0
120
(32)
240
(64)
360
(96)
bar
(psi) 220 (cfm)
165
480
(128)
KIND OF FLUID: Water 68 °F
m3/min
cycles/min
38
8
(116)
A
6
(87)
B
4
(58)
C
75
4
(140)
A
B
3
(105)
2
(70)
C
2
(29)
0
l/min
gpm
1
(35)
0
155
(41.5)
310
(83)
465
(125)
bar
(psi) 150 (cfm)
113
620
(166)
KIND OF FLUID: Water 68 °F
m3/min
cycles/min
38
75
150 (cfm)
113
8
(116)
A
A
4
(140)
6
(87)
B
B
3
(105)
4
(58)
C
2
(70)
C
2
(29)
0
l/min
gpm
1
(35)
0
150
(40)
300
(80)
450
(120)
600
(160)
KIND OF FLUID: Water 68 °F
AIR CONSUMPTION
C
N° 1 packing cf 5.6
FLUID OUTLET PRESSURE
0,13
(4.7)
4
(58)
lb 95
AIR CONSUMPTION
2
(29)
0
l/min
gpm
B
0,27
(9.5)
C
B
16.1” x 17” x 28”
N° 1 packing cf 5.6
FLUID OUTLET PRESSURE
C
6
(87)
18.2” x 17” x 24.2”
lb 56
AIR CONSUMPTION
4
(58)
0,4
(14.2)
N° 1 packing cf 2.3
FLUID OUTLET PRESSURE
4 bar (58 psi)
B
13.8” x 15.8” x 20.2”
lb 42
AIR CONSUMPTION
C
B
N° 1 packing cf 1.35
FLUID OUTLET PRESSURE
C
6
(87)
A
11.3” x 9.4” x 15.2”
lb 30
AIR CONSUMPTION
6 bar (87 psi)
8
(116)
150
N° 1 packing cf 0.9
*** With PTFE membrane flow rate is 10 % lower
cycles/min
75
10.3” x 7.9” x 13.6”
lb 17.6
FLUID OUTLET PRESSURE
B
A
340 (cfm)
0,53
A
(19)
N° 1 packing cf 0.5
AIR CONSUMPTION
B
8
(116)
255
7.9” x 6.3” x 10”
lb 26.5
FLUID OUTLET PRESSURE
8 bar (116 psi)
170
bar
(psi) m3/min
cycles/min
85
FLUID OUTLET PRESSURE
A
FLUID OUTLET PRESSURE
C
A
bar
(psi) AIR CONSUMPTION
PUMP AIR
FEEDING PRESSURE
14” x 7.8” x 16.5”
N° 1 packing cf 0.9
AIR CONSUMPTION
Overall dimensions (A x B x C)
8.6” x 7” x 12.8”
8.6” x 7” x 12.8”
11.8” x 7.9” x 17.9”
Packing - Weight
N° 1 packing cf 0.9
lb 26
N° 1 packing cf 0.5
lb 15.4
N° 1 packing cf 0.5
lb 15.4
** Different kind of muffler are available on request for special use or hard work
* Displacement per cycle may be influenced by suction lift, fluid viscosity, air pressure, number of cycles per minute
IDEAL FOR ANY
INDUSTRY
GLASS INDUSTRY
PETROCHEMISTRY
CHEMICAL INDUSTRY
MINING AND BUILDING CONSTRUCTIONS
PHARMACEUTICS INDUSTRY
SHIPYARD
SEMICONDUCTOR INDUSTRY
PAINT INDUSTRY
MOTOR INDUSTRY
PAPER MILL
TEXTILE INDUSTRY
PRINT INDUSTRY
CERAMIC INDUSTRY
FOOD INDUSTRY
ELECTRONIC INDUSTRY
RAASM USA, Inc.
1704 East Blvd, Suite 101
Charlotte, NC 28203 USA
Phone +1 704 370 1906
Fax +1 704 373 2603
[email protected]
www.raasmusa.com
All rights reserved to Raasm S.p.A.
WRUDA/D.P.2010-USA
Authorized distributor