cruzer - Beacon Products

CRUZER
SERIES
Cat.#
Type
Job
design . per formance . technology
Approvals
CRUZER AREA LUMINAIRE
SPECIFICATIONS
PRODUCT IMAGE(S)
Intended Use:
The Beacon Cruzer luminaire is a pole mounted
luminaire with a field replaceable LED light engine
& optical bezel system. Internal components
are totally enclosed in rain-tight and corrosionresistant die cast aluminum housing. The CRZ
Luminaire is CSA listed and suitable for wet
locations.
• Component-to-component wiring within the luminaire may carry no more than 80% of
rated load and is listed by UL for use at 600VAC at 50°C or higher.
• Plug disconnects are listed by UL for use at 600 VAC, 15A or higher. 15A rating applies to primary (AC) side only.
• Surge protection - 20KA; Shuts off at end of life.
Controls/Options:
LED/Optics:
• Optical one piece cartridge system consisting of an LED engine, LED lamps, optics, gasket and stainless steel bezel.
• Cartridge is held together with internal brass standoffs soldered to the board so that it can be field replaced as a one piece optical system.
• Two-piece die cut silicone and polycarbonate foam gasket ensures a weather-proof seal around each individual LED and allows
the Cruzer luminaire to be rated for
high-pressure hose down applications.
• Optical cartridge is secured to the housing with
fasteners and a heat pad to ensure thermal conductivity.
• Optics are held in place without the use of adhesives and the complete assembly is gasketed for high pressure hose down
cleaning.
• Cartridge assembly is available in various lighting distributions using TIR designed acrylic optical lenses over each LED.
Electrical:
• LED driver accepts 100V through 277V, 50 Hz to 60 Hz (UNV), or 347V or 480V input.
• Power factor is .92 at full load.
• All electrical components are rated at 50,000 hours at full load and 40°C ambient conditions per MIL-217F Notice 2.
• Optional 0 to 10 volt dimming drivers are available upon request.
• Available with an optional passive infrared (PIR) motion sensor capable of detecting motion 360° around the luminaire. When no motion is detected for the specified time, the Motion Response system reduces the Wattage to factory preset level, reducing the light level accordingly. When motion is detected by the PIR sensor, the luminaire returns to full Wattage and full light output. Please contact Beacon Products if project requirements vary from standard configuration. • Available with Energeni for optional set
dimming, timed dimming with simple delay, or timed dimming based on hours of operation or time of night (see www.beaconproducts.com/
products/energeni).
DIMENSIONS
• Also available with Beaconnect Wireless Control System (see Beaconnect product page for more details www.beaconproducts.com/
products/beaconnect). AM Arm Mount
18 1/2”
Installation:
• Arm mount for attachment to round or square pole.
• Slip fitter or adjustable knuckle fits 2 3/8” arm or tenon.
• Wall bracket for simple wall mounting.
• Suitable for applications requiring 3G testing prescribed by ANSI C136.31.
SF2 2-3/8” OD Slipfitter
15 3/4”
Finish: • Beacote V polyester powder-coat electro-
statically applied and thermocured.
• Beacote V finish consists of a five stage pretreatment regimen with a polymer primer sealer and top coated with a thermoset
super TGIC polyester powder coat finish.
• The finish meets the AAMA 605.2 performance specification which includes passing a 3000 hour salt spray test for corrosion resistance and resists cracking or loss of adhesion per ASTM D522 and resists surface impacts of up to 160 inch-pounds.
15 3/4”
PK2 2-3/8” Adjustable Knuckle
Listings:
The luminaire shall be NRTL certified to UL 1598
and 8750 standards for use in wet locations.
Warranty:
Five year limited warranty (for more information
visit: http://www.hubbelllighting.com/resources/
warranty).
WB Wall Bracket
18 1/2”
1/2”
5 1/2”
1”
2 3/8”
5”
CERTIFICATIONS/LISTINGS
6”
*3000K and warmer CCTs only
Beacon Products • 2041 58th Avenue Circle East Bradenton, FL 34203 • Phone: 800-345-4928
Due to our continued efforts to improve our products, product specifications are subject to change without notice.
design . per formance . technology
EPA
0.8 ft2
Weight:
25.0 lbs
(11.3 kg)
15 1/2
• Die cast aluminum two-piece housing.
• Die cast main (thermal) housing provides direct heat exchange between the LED light engine and the cool outdoor air by drawing heat through integral heat channels and out to the sculptured and functional luminaire
surface.
• LED drivers are thermally isolated from the main housing, mechanically attached and heat sinked to the rear housing.
• Main housing is designed with heat dissipating fins for LED thermal management without the use of metallic screens, cages, or fans.
• Shape of the main housing is designed to
prevent debris accumulation and is a bird nesting deterrent. Back and main housings are designed to hinge open for easy mounting and easy access.
7 1/2”
Construction:
© 2016 BEACON PRODUCTS, All Rights Reserved • For more information visit our website: www.beaconproducts.com • Printed in USA SPEC 6/16
ORDERING INFORMATION
ORDERING EXAMPLE: CRZ/60NB-135/5K/T2/UNV/2PF/GENI-04/AM/BBT
CRZ
SERIES
CRZ Cruzer
ENGINE-WATTS
LED COLOR
VOLTAGE
24NB-27 27W, LED
3K 3000K
4K 4000K
5K 5000K
UNV 120-277V
array
24NB-55 55W, LED
array
ELECTRICAL
OPTIONS
OPTICS
48NB-110 110W,
LED array
60NB-136 136W,
LED array
WIS1,7
480V 480V
T2 type II
PEC photocell, button
T3 type III
2PF1 dual power feed
WISSC
1,7
T4 type IV
T5R type V, rectangular
T5QM type V, square
FINISH
MOUNTING OPTIONS
SF2 2 3/8” OD slip-fitter
PK2 2 3/8” adjustable
GENI-XX3,7 energeni
347V 347V
36NB-80 80W, LED
array
CONTROL
OPTIONS
knuckle
WB wall bracket
wiSCAPE
Fixture Module,
in-fixture
relay for
wireless lighting
control
wiSCAPE
Fixture Module,
in-fixture relay
for wireless
lighting control
and motion/
occupancy
control
AM arm mount
basic black textured
black matte textured
white textured
metallic bronze textured
bronze textured
dark bronze textured
gray smooth
DPS dark platinum smooth
GNT green textured
MST metallic silver textured
MTT metallic titanium textured
BCW5,6,7 beaconnect
medium
T5W type V, round wide
BBT
BMT
WHT
MBT
BZT
DBT
GYS
OWI old world iron
SENSOR
OPTIONS
CC _____________
MOB2,7 motion sensor
MOB ORDERING INFORMATION: When ordering a fixture with the motion detection option
(MOB), please specify the appropriate information. These settings are specified in the ordering
as shown in the example below.
SHIELD OPTIONS
33% or 50%
dimming
BLC4 backlight control
OCS7 occupancy
33% or 50% - _____
1 to 30 min. - __________
?? / MT
CRZ / 36NB-80 / 5K / T5W / UNV / MOB - __________
BMD5,6,7
High to Dim Delay Low Level Mounting Height (ft.)
180 180° house side shield
sensor (on/
off)
beaconnect
with motion
sensor
270 270° house side shield
360 360° house side shield
BEACONNECT ORDERING INFORMATION: When ordering a fixture with the Beaconnect lighting control options
please specify the appropriate group and sensor information. Please provide dimming schedule information in
either the Beaconnect excel spreadsheet or Beaconnect software. For more detailed information please visit www.
beaconproducts.com/beaconnect or contact beacon tech support at (800) 345-4928. These settings are specified in
the ordering as shown in the example below. (Family) / 24NB-55 / 5K/ T3 / UNV / BCW-(Group 1-16)_____-_(Optional
Zone 1-250)_ /BMD - __Time Delay(1 to 255)_ - ____Dimming% (1 to 100)__ - __mounting height(1-20ft)___/
Example: CRZ/24NB-55/5K/T3/UNV/BCW-G1 /BMD-30M-50%-10F/DBT for luminaires without sensors in the group
omit the BMD ordering logic Example: CRZ/24NB-55/5K/T3/UNV/BCW-G1 /DBT
DesignLights Consortium qualified.
Consult DLC website for more details:
http://www.designlights.org/QPL
not available @ 347V or 480V input
not available on 48NB-110, not available on 60NB-136
When ordering Energeni, specify the routine setting code (example GENI-04). See Energeni brochure and instructions for setting table and options. Not available with sensor options.
4
Type 4 (T4) optics only
5
Must specify group and zone information at time of order. See www.beaconproducts.com/controls/beaconnect for further details
6
Specify time delay; dimming level and mounting height.
7
Not available with other control or sensor options.
1
2
3
PHOTOMETRICS
Type II
CRZ-60NB-136-5K-T2
Type III
CRZ-60NB-136-5K-T3
100’
25’
50‘
75‘
25‘
1fc
25‘
75‘
.5fc
2fc
50‘
25’
50‘
25‘
Type IV
CRZ-60NB-136-5K-T4
100’
50‘
75‘
25’
25‘
75‘
.5fc
100‘
1fc
25‘
75‘
1fc
.5fc
Type V Round Wide
CRZ-60NB-136-5K-T5W
Type V Square Medium
CRZ-60NB-136-5K-T5QM
40‘
40‘
40‘
20‘
20‘
20‘
40’
40’
40’
10’
20‘
10’
20‘
20‘
1fc
.5fc
10’
20‘
20‘
40‘
20‘
20‘
20‘
40‘
40‘
40‘
40‘
75‘
2fc
100‘
100‘
Type V Rectangular
CRZ-60NB-136-5K-T5R
50‘
100‘
50‘
75‘
75‘
100‘
25‘
25‘
100‘
2fc
50‘
75‘
25‘
50‘
25‘
100’
50‘
1fc
.5fc
20‘
1fc
.5fc
40‘
Beacon Products • 2041 58th Avenue Circle East Bradenton, FL 34203 • Phone: 800-345-4928
Due to our continued efforts to improve our products, product specifications are subject to change without notice.
design . per formance . technology
© 2016 BEACON PRODUCTS, All Rights Reserved • For more information visit our website: www.beaconproducts.com • Printed in USA SPEC 6/16
PERFORMANCE DATA
5K
(5000K nominal, 70 CRI)
# LED’S
DRIVE
CURRENT
(MILLIAMPS)
SYSTEM
WATTS
24
350mA
27W
24
700 mA
55W
36
700 mA
80W
48
700 mA
110W
60
700 mA
136W
DISTRIBUTION TYPE
T2
T3
T4
T5QM
T5R
T5W
T2
T3
T4
T5QM
T5R
T5W
T2
T3
T4
T5QM
T5R
T5W
T2
T3
T4
T5QM
T5R
T5W
T2
T3
T4
T5QM
T5R
T5W
LUMENS
2833
2805
3086
3085
3142
3044
5666
5610
6171
6171
6283
6087
8505
8415
9256
9257
9425
9131
11332
11220
12342
12342
12567
12175
14165
14025
15427
15427
15708
15218
LPW1
105
104
114
114
116
113
102
101
111
111
113
109
101
100
110
110
112
109
102
101
111
111
113
110
103
102
113
113
115
111
B
1
1
1
2
2
2
2
1
1
3
3
3
2
2
1
3
3
3
3
2
2
3
4
4
3
3
2
4
4
4
U
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
4K
(4000K nominal, 70 CRI)
G
1
1
1
0
2
1
2
2
2
1
3
1
3
2
3
1
3
2
3
3
3
2
4
2
3
3
3
2
4
2
LUMENS
2805
2777
3055
3055
3111
3014
5610
5554
6110
6110
6221
6027
8415
8331
9164
9164
9331
9040
11220
11108
12219
12219
12441
12053
14025
13885
15274
15274
15259
15551
LPW1
104
103
113
113
115
112
101
100
109
109
111
108
100
99
109
109
111
108
101
100
110
111
112
109
102
101
111
111
111
114
B
1
1
1
2
2
2
2
1
1
3
3
3
2
2
1
3
3
3
3
2
2
3
4
4
3
3
2
4
4
4
3K
(3000K nominal, 70CRI)
U
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
G
1
1
1
0
2
1
2
2
2
1
3
1
3
2
3
1
3
2
3
3
3
2
4
2
3
3
3
2
4
2
LUMENS
2408
2392
2623
2623
2670
2600
4816
4784
5245
5245
5341
5201
7224
7175
7868
7868
8011
7801
9633
9567
10491
10491
10682
10402
12041
11959
13114
13314
13352
13002
LPW1
89
89
97
97
99
96
86
86
94
94
96
93
87
86
94
94
96
93
87
86
95
95
96
94
88
87
96
96
97
95
B
1
1
1
1
2
2
1
1
1
2
3
3
2
2
1
3
3
3
2
2
2
3
3
4
3
3
2
3
4
4
U
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
G
1
1
1
0
2
1
2
2
2
1
3
1
2
2
3
1
3
2
3
3
3
2
3
2
3
3
3
2
4
2
Lumen values are from photometric tests performed in accordance with IESNA LM-79-08. Data is considered to be representative of the configurations shown. Actual performance may differ as a result of end-user environment and application.
1
ELECTRICAL DATA
# OF LEDS
NUMBER
OF
DRIVERS
PROJECTED LUMEN MAINTENANCE
DRIVE
CURRENT INPUT VOLTAGE SYSTEM POWER
(mA)
(V)
(w)
24
1
350 mA
24
2
700 mA
36
1
700 mA
48
1
700 mA
60
1
700 mA
120
277
347
480
120
277
347
480
120
277
347
480
120
277
347
480
120
277
347
480
27
55
80
110
136
CURRENT
(Amps)
0.2
0.1
0.1
0.1
0.5
0.2
0.2
0.1
0.7
0.3
0.2
0.2
0.9
0.4
0.3
0.2
1.1
0.5
0.4
0.3
AMBIENT
TEMP.
25°C / 77°C
TM-21-11
Calculated L70
60,000
100,000
(HOURS)
0.94
0.91
>434,000
1
0 25,000
1.00 0.97
50,000
0.95
1
Projected per IESNA TM-21-11
Data references the extrapolated performance projections for the base model in a 40°C
ambient, based on 10,000 hours of LED testing per IESNA LM-80-08.
AMBIENT
LUMEN
TEMPERATURE MULTIPLIER
0°C
32°F
1.02
10°C
50°F
1.01
20°C
68°F
1.00
25°C
77°F
1.00
30°C
86°F
1.00
40°C
104°F
0.99
50°C
122°F
0.98
Use these factors to determine relative lumen
output for average ambient temperatures from
0-50°C (32-122°F).
Beacon Products • 2041 58th Avenue Circle East Bradenton, FL 34203 • Phone: 800-345-4928
Due to our continued efforts to improve our products, product specifications are subject to change without notice.
design . per formance . technology
© 2016 BEACON PRODUCTS, All Rights Reserved • For more information visit our website: www.beaconproducts.com • Printed in USA SPEC 6/16