doc2013 Hyundai Santa Fe CNM5-DM1-8 installation
download 
Report Transcription
2013 Hyundai Santa Fe CNM5-DM1-8 installation
Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual 2013-‐UP Santa Fe Standard radio (w/o factory reverse camera) REV:1.0 NOTES:THIS KIT FITS ONLY THE ABOVE RADIO! 1 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual DISCLAIMER: This installa>on manual is intended for informa>onal and reference purpose only. We do not recommend implicitly or explicitly, to anyone performing any of the procedures described in this manual. We are also not responsible for any property damage, personal injury and or death, or any other loss or damage that may result from following this manual. Proceed with cau>on and care when performing modifica>ons to your vehicles may void your manufacturer’s warranty. REV:1.0 NOTES: 2 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual -‐ Read installa>on manual instruc>ons carefully. Installer must careful to not cause interference between Navigator System cabli ng and ac>ve / passive car safety device (Ex: Air bags, seat belts, indicators, etc…) -‐ Turn OFF the radio. -‐ Before any a]empt of component removal, the installer must disconnect the vehicle ba]ery (-‐) and isolate the end of the cable. -‐ Do not a]empt this installa>on opera>on if there are missing components. Please check the bill of materials carefully to ensure the kit is complete. -‐ Installa>on requires careful a]en>on. If you have concerns about your abili>es to perform delicate opera>ons, then do not begi n the installa>on. -‐ The car must be secured to not move during installa>on. Parking brake must be engaged at all >mes. -‐ Opera>on should be made in a clean, safe and well ven>lated environment without trip hazards and slippery floors -‐ Do not install by yourself if you do not have qualifica>ons and/or tools to perform the retrofit. You may damage the car’s comp onents and/or the Navigator if not professionally installed. -‐ Poor installaDon can result in poor performance, personal injuries and will immediately void the factory warranty. -‐ Do not install the Navigator in a posiDon that blocks the driver's view or hinders safe vehicle operaDon. REV:1.0 NOTES: 3 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Cau>on: -‐ -‐ -‐ -‐ -‐ This kit only fits the model outlined. Kits are not interchangeable with other vehicles. Read this manual in depth prior installa>on. Call our support if sec>ons are not clear. Always remove the ba]ery nega>ve (-‐) lead from the car prior installa>on. Never install this kit with ambient temperature below 10 C (50 F). The trip module and the radio described into this manual are sensi>ve devices. Always interface both with delicate a]en>on; the radio must always be outside of the vehicle. -‐ Always protect surface surrounding your work to avoid damages (scratches, dents, etc…) -‐ InstallaDons performed without reading this manual will void the warranty instantly. ! -‐ Callouts requires you to look the NOTES sec>on for special instruc>ons. -‐ Do NOT RUSH, if issues occur contact technical support: -‐ (514) 944-‐2628 -‐ support@compass-‐nav.com REV:1.0 NOTES: 4 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Table of contents: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. REV:1.0 Tools Required – Bill of Materials – Touchscreen Connec>ons iden>fica>on – Cables interconnec>on iden>fica>on – TRIP Module connec>on iden>fica>on – Vehicle Prepara>on – Radio Prepara>on – Radio Bracket Installa>on – Glove Box Prepara>on – Electrical Connec>ons – Installa>on in Vehicle – Appendix 1 – Reverse Camera Installa>on Appendix 2 – Parking Assist Appendix 3 – RDS Traffic Tuner Appendix 4 – iR Remote Control Appendix 5 – Troubleshoo>ng Guide NOTES: Page 6 Page 7 Page 10 Page 15 Page 22 Page 25 Page 34 Page 48 Page 50 Page 54 Page 61 Page 77 Page 80 Page 83 Page 85 Page 87 5 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual 1.0 Tools required: -‐ -‐ -‐ -‐ -‐ -‐ -‐ Industrial double side tape (3M Red) Masking tape Electrical insula>on tape Hacksaw Magne>c Philips screw driver Flat screw driver Vice Grip REV:1.0 -‐ -‐ Wire stripper Dash panel removal tools NOTES: 6 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual 2.0 Bill of materials Keypad Cable (Pre-‐installed) Aux cable Audio T-‐ Harness Main I/O 1 Harness Main I/O 2 Harness (OpDonal) REV:1.0 NOTES: 7 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual …Bill of materials Flat ribbon rubber block Radio face plate Mini Speaker and one screw Radio securing Brackets GPS antenna TRIP Serial cable REV:1.0 NOTES: 8 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual …Bill of materials TRIP Module and two screws Fascia Molding & Pre-‐installed touchscreen SD Card (Pre-‐ inserted into Ext. Media Box XM Adapter Flat Ribbon (OpDonal see SecDon 7) REV:1.0 NOTES: External USB & SD Card Box 9 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Sec>on 3 Touchscreen Connec>on iden>fica>on REV:1.0 NOTES: 10 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Reserved for future use Main I/O 1 Main I/O 2 SD/USB connect Power Connec>on REV:1.0 NOTES: 11 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual SD/USB connec>on box to SD EXT connec>on SD/USB Interface Main I/O #1 Connec>on REV:1.0 NOTES: 12 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Main I/O #2 Connec>on Connect only if the following opDon(s) was(were) purchased: -‐ Live Traffic module -‐ Rear Screen -‐ Infrared Remote REV:1.0 NOTES: 13 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Power connector for the CN-‐M5 Navigator coming from the Audio T-‐Harness REV:1.0 NOTES: 14 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Sec>on 4 System Cable Connec>ons and Iden>fica>on REV:1.0 NOTES: 15 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual MAIN I/O #1 Rear Backup Camera Cable -‐ Main I/O #1 Backup lamp +12V from Camera RED wire Ground GPS Antenna Connec>on – Main I/O #1 REV:1.0 NOTES: 16 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual MAIN I/O #1 External Speaker Connec>on – Main I/O #1 TRIP Serial Cable connec>on: -‐ 5 Pin to TRIP Module -‐ 3 Pin(Yellow, Red and Black) to MAIN I/O #1 Trip Serial cable -‐ 2 Pin(Blue and Green) to Audio T-‐ Harness REV:1.0 NOTES: 17 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual MAIN I/O #1 AUX Cable connec>on – Main I/O #1 To Audio T-‐Harness AUX IN (3.5mm male jack) AV In connec>on – Main I/O #1 (Op>onal) REV:1.0 NOTES: Composite & stereo jacks DVD, Game console etc… 18 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual MAIN I/O #2 AV Out Connec>on – Main I/O #2 Rear seats Composite stereo jacks IR Sensor and Remote – Main I/O #2 (Op>onal) REV:1.0 NOTES: 19 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual MAIN I/O #2 Live Traffic module (TMC) – Main I/O #2 (Op>onal) REV:1.0 NOTES: 20 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Audio T-‐Harness Audio switcher: -‐ AUX from MAIN I/O #1 -‐ (Female 3.5 mm jack) AUDIO SWITCHER -‐ Steering wheel control wires (Blue & Green) 2 pins from TRIP SERIAL Cable. REV:1.0 NOTES: 21 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Sec>on 5 Trip Module Connec>ons and port iden>ty REV:1.0 NOTES: 22 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Trip Module Connec>ons/Cable iden>fica>on TRIP serial and steering wire connector Ribbon Connector Keypad Connector OBDII Parking Assist cable (Op>on) REV:1.0 NOTES: 23 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual TRIP module schemaDc connecDons OBD Parking Assist connector (op>on) CN-‐M5 Screen TRIP Serial connector I/O Keypad cable Flat Ribbon Cable Steering wheel cables REV:1.0 NOTES: 24 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Sec>on 6 Vehicle Prepara>on REV:1.0 NOTES: 25 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Protect the vents surrounding area with masking tape to prevent surface damage as shown. REV:1.0 NOTES: 26 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Carefully pry away the vent towards you star>ng at the bo]om of the vent to gain enough to begin removing by hand. Store the vents pieces carefully to avoid damage. Repeat the process for the other side. REV:1.0 NOTES: 27 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Once both vents are removed , the radio securing screws are exposed. Remove both screws and reserve. Repeat on the other side. REV:1.0 NOTES: 28 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Gently ease the radio forward to expose the rear. REV:1.0 NOTES: 29 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Disconnect the FM and XM antenna from the rear of the radio. Cau>on, press the locking tab arer the pink plas>c to disengage the XM antenna. A li]le flat screw driver may help. XM To free the radio completely disconnect the 2 mul>-‐way connectors on the rear of the radio. Pressing the locking tab down allows the connectors to be removed from the back. FM Santa Fe base model radio shown REV:1.0 NOTES: 30 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual The red lines iden>fy the area that needs to be trimmed. The factory radio will be located deeper in the dash than before to accommodate the new touchscreen and bezel mount. Be careful to not cut electrical wires!!!! Using a small saw (or any appropriate tool) trim the area marked to reflect the next step. This is necessary to allow the updated radio to be installed correctly. Clean the enDre area with a vacuum to remove the plasDc debris. REV:1.0 NOTES: 31 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Bend all the way down the radio suppor>ng bracket as shown. Doing this ensures enough clearance to posi>on the cables under the radio at final assembly. The bracket can also be snapped off by moving it up and down several >mes with a vice grip. It should break at the soldering points. REV:1.0 NOTES: 32 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Remove the securing clip from the car harness. Doing this will ensure enough clearance at the back of the radio for final assembly. REV:1.0 NOTES: 33 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Sec>on 7 Radio Prepara>on (A]en>on Required!) REV:1.0 NOTES: 34 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Remove exis>ng retaining brackets using a Phillips head screwdriver. Secure the 4 screws removed as they will be re-‐used. REV:1.0 NOTES: 35 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Remove the 6 front panel retaining screw as shown. (2 opposite side) To detach the front panel completely from the radio, there are 8 retaining tabs that retain the radio panel in ( 2 on bo]om, 2 on top and 2 either side) . GENTLY lir these up a li]le (DO NOT SNAP THEM OFF) and pry the radio fascia clear enough to allow access to the cables on the rear. A second flat screw driver might help to keep the clips released while unclipping others. REV:1.0 NOTES: 36 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual ! Once the front panel is free of the chassis, you need to detach one end of the ribbon cable. See next… REV:1.0 NOTES: Pull the front panel gently to avoid connector & ribbon damage 37 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Radio Version IdenDficaDon: Hyundai produced two different versions for the Santa Fe. Look where the flat ribbon a]aches to the radio motherboard. If the radio has a brown/beige connector on the motherboard. The flat ribbon doesn't need to be changed since the opposite end has the matng contacts in the right orienta>on. You will detach the ribbon from the radio face plate and you won’t need the supplied ribbon cable. Proceed to the next page… ! REV:1.0 If the radio has a black connector on the motherboard. The flat ribbon needs to be changed since the opposite end has the matng contacts in the wrong orienta>on. You will detach the ribbon from the radio motherboard and you will need the supplied ribbon. Go to page 41… NOTES: The above step is crucial! 38 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Brown / Beige connector style: A li]le pressure is needed from a screwdriver to lir up the brown locking tab to allow the ribbon cable to freely be disconnected. Be gentle to avoid damaging the brown locking tab No>ce the red circles. The cable needs to be disengaged from the unlocked brown locking tab, to free it from the beige connector. Separate the white end from the lock by liring gently. DO NOT PULL HARD REV:1.0 NOTES: 39 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Brown / Beige connector style: Once the cable disengages from the brown locking tabs gently remove the ribbon cable from the beige connector Ribbon Cable disconnected Jump to page 42 REV:1.0 NOTES: 40 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Black connector style: Gently lir up the back locking tab and pull the ribbon to disengage it from the motherboard. Take the ribbon cable supplied with the kit and gently feed it it the connector same way the original was; Blue stripe up, ma>ng contacts down. Gently fold down the black locking tab. Jump to next page. REV:1.0 NOTES: 41 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Remove the 2 screws holding the CD player as indicated here and save these separately because they are smaller. Then remove the 5 screw surrounding the face plate REV:1.0 NOTES: 42 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Assemble the trip module with the supplied screws as indicated. The connectors must face the face plate with the flat ribbon connector located at the ler TRIP module correctly installed REV:1.0 NOTES: 43 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Run the flat ribbon thru the new face plate carefully. Make sure not bend the flat ribbon. Then assemble the new face plate and locate it using the embosses circled. Screw (3) the face plate star>ng by the opposite corners to make sure the radio body is square. Place a screw as shown, this will be use to ground the CN-‐M5 reverse camera REAR PWR. Screw the CD player at the top of the slots as shown using the small screws reserved separately. Proceed with the flat ribbon install Next page… REV:1.0 NOTES: 44 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual ! 1 2 3 REV:1.0 1-‐ Lir and hold the black locking tab 90 deg up to allow the ribbon cable to be installed into the TRIP module freely. 2-‐ The flat ribbon contacts (silver) need to face down (to make contact) and the blue stripe needs to face up. The ribbon must be CAREFULLY but firmly pushed into the TRIP connector, ensuring it is parallel and has no bends or tears. SEE NOTES! 3-‐ Then fold down gently the locking tab applying the pressure in the middle of the tab. NOTES: The blue sDpe of flat ribbon is always facing up at the trip module WITHOUT twisDng or rotaDng the ribbon 180 deg. Otherwise, STOP the installaDon immediately and contact support 45 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual 4 4-‐ Then carefully install the rubber retainer, inser>ng the bo]om piece first into place to ensure the locking tab and therefore ribbon cable does not disengage. Cau>on: Make sure to insert the bocom of the rubber block first otherwise the locking tab may fold back and brake. If the locking tab is broken; stop the installaDon immediately and contact support. 5-‐ The protruding curve of the ribbon cable must be CAREFULLY eased back into the radio unit (under the TRIP module), use just enough pressure to push into the radio. Completed TRIP module ribbon cable installa>on! REV:1.0 NOTES: 46 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual A]ach the XM radio antenna adapter to the radio as shown You have successfully retrofi]ed your factory radio! REV:1.0 NOTES: 47 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Sec>on 8 Radio Bracket installa>on REV:1.0 NOTES: 48 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual TOP A]ach the dash moun>ng brackets, supplied with the kit, to the side of the radio using the 2 screws reserved previously. Alignment the bracket in dimple (GREEN circle) to locate the brackets correctly. NOTE – Look at the orienta>on of the bracket, the brackets extend the bo]om of the radio chassis. Repeat for the other side of the radio. You have successfully prepared your radio. REV:1.0 NOTES: 49 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Sec>on 9 Glove Box Prepara>on REV:1.0 NOTES: 50 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Open the glove box and rotate the guides (1) and remove them. Disconnect the cylinder (2) to completely release the glove box. 1 2 REV:1.0 NOTES: 51 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Apply 2 strips of double sided tape at the back of the external media box as shown or use the supplied screws. REV:1.0 NOTES: 52 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual ! Route the External Media Storage connector under the radio loca>on. Peel the red tape from the double face tape and affix as shown. Affix the Media box against the lef inner wall and 2” from the face as shown. Secure the storage cord beside the air filter box with a >e-‐rap. Trim the top of the glove box to clear the Storage box IF NEEDED. The SD Card might parDally eject during the box installaDon process. Press The SD Card to eject and re-‐ insert. You should hear a faint “click “ REV:1.0 NOTES: Make sure you expose the media ports (USB & SD) to access them for future system maintenance 53 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Sec>on 10 Electrical/Wiring Connec>ons REV:1.0 NOTES: 54 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual In the following sec>on we will: -‐ Prepare the Audio T-‐Harness for the final assembly -‐ A]ach the Audio T-‐Harness to the car & radio connectors -‐ Video Tutorial about this sec>on: h]ps://dl.dropboxusercontent.com/u/70065767/Manuals/Audio%20Patch%20Cord%20Assy.m2ts Parts Required: Audio T-‐Harness Aux cable TRIP Serial cable REV:1.0 NOTES: 55 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual A]ach the TRIP Serial cable 2 Pin connector (Blue & Green) to this connector of the Audio T-‐ Harness as shown. TRIP Serial cable REV:1.0 NOTES: 56 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual A]ach the AUX cable male jack into the female of the Aux switcher board as shown. Secure in place with Electrical tape. Reserve the White and RED RCA jack to be connected into the AUX cable from the MAIN I/O 1 Aux cable REV:1.0 NOTES: 57 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Connect the male of Audio T-‐Harness to the car’s female matching connector as shown. Connector improperly seated. Connector properly seated. You should hear a CLICK. REV:1.0 NOTES: 58 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Reserve the CN-‐M5 4 pins square power connector for the final assembly. Reserve the TRIP SERIAL to be a]ached to MAIN I/O 1 TRIP SERIAL. (3 Pins Red, Yellow, Black) Reserve the TRIP MOD cable for the final assembly. It will be plugged in front of the trip module. (5 pins Black, Yellow, Red, Blue and Green) REV:1.0 NOTES: 59 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Mini speaker installa>on The recommended placement of the mini-‐speaker is located on the driver side. Using the provided screw, a]ach the mini speaker to the side kick panel as shown. The speaker is very light and require only one screw. Once completed, bring the wire to the head unit for final install. Air vent Driver side kick panel REV:1.0 NOTES: 60 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Sec>on 11 Installa>on into Vehicle REV:1.0 NOTES: 61 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Loca>on of GPS antenna in the dashboard Using 3M tape a]ach the GPS antenna above the air duct underneath the dashboard surface. “GPS” le]ers of the antenna should be towards the sky. Tes>ng has shown that signal is very strong at this loca>on. Route the GPS cable under the radio area clearing the duct openings. REV:1.0 NOTES: 62 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual IMPORTANT Before proceeding to the final installa>on if you have purchased the following op>ons, please proceed to their installa>on before comple>ng the final assembly. -‐ Backup Camera Appendix 1 page 77 -‐ Parking Assist System Appendix 2 page 80 -‐ RDS Traffic Tuner Appendix 3 page 83 -‐ iR Remote Control Appendix 4 page 84 REV:1.0 NOTES: 63 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual MAIN I/O 1 & 2 ConnecDon Prior the assembly of the trim to the car, please make sure you have at least the following connected properly . -‐ GPS Antenna to GPS Serial of MAIN I/O 1 ( White, Red, Black & Black) -‐ TRIP cable to TRIP Serial of MAIN I/O 1 (Black, Yellow & Red) -‐ Mini Speaker to SPK of MAIN I/O 1 (Red & Black) -‐ AUX cable to AUX of MAIN I/O 1 (secure both White & Red RCA jacks with electrical tape) -‐ -‐ -‐ -‐ -‐ -‐ OPTIONS: CAMERA to CAMERA of MAIN I/O 1 Audio Video Extension cord to AVIN of MAIN I/O 1 for external mul>media player Audio Video Extension cord to AVOUT of MAIN I/O 2 for read seat screen and sound IR Receiver for Infrared remote of MAIN I/O 2 TMC cable to TMC Traffic receiver of MAIN I/O 2 REV:1.0 NOTES: 64 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Arer ensure all cables are correctly brought through to area beneath radio, a]ach: -‐ Radio antenna -‐ XM antenna -‐ MulD-‐way connectors (2) -‐ Audio T-‐Harness goes into the first spot. And install radio in dashboard. If the radio does not fit well in place, make sure there is no unnecessary cables behind it and ensure they are well placed under the radio. Affix using the screws removed earlier. REV:1.0 NOTES: 65 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Prior installing the fascia, connect: -‐ -‐ -‐ The TRIP cable to the TRIP module as indicated (5 PINS) Parking Assist cable (3 PINS) (if purchased). A]ach the REAR PWR ground terminal at the bo]om of the radio chassis for the backup camera to work properly (if purchased). Getng ready to a]ach the new fascia trim, connect: -‐ Keypad green cable to the TRIP -‐ Module. -‐ Connect in the following order at the back of the screen: -‐ REV:1.0 -‐ Main I/O 1 -‐ Main I/O 2 (If needed) External media box (SD Card/USB) -‐ CN-‐M5 Power (4 PINS square) NOTES: 66 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Install the facia temporarily in place and plug back the nega>ve lead to the ba]ery and test run the CN-‐M5 navigator. -‐ Make sure the parking brake is engaged -‐ Make sure the car transmission is in “P” (Park) posi>on -‐ Place the igni>on switch to the Accessory posi>on by turning the igni>on switch to the “ACC” posi>on or pushing the start/stop bu]on one >me (without depressing the brake pedal). -‐ You should see the following boot screen for approximately 7 seconds. REV:1.0 NOTES: 67 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual AUDIO CONFIGURATION Upon the first system boot-‐up, you may this box showing-‐up… -‐ -‐ -‐ -‐ REV:1.0 Make sure that the BT /in box is >cked Tick 8Keys/Vol/PWR Then >ck SantaFe dm Press CLOSE NOTES: 68 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Basic system configuraDon From the HOME screen, look for a gear icon as shown If you have this HOME screen, press on the right arrow to access the second page and locate the gear icon REV:1.0 NOTES: 69 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Press the DISPLAY tab and: -‐ Set the DAY TIME BRIGHNESS to 10 -‐ Set the NIGHT TIME BRIGHNESS to 0 Press the VOLUME tab and: -‐ Set the SPEAKER VOLUME to 8 -‐ Set the AUX VOLUME to 8 -‐ Tick the TRIP COMPATIBLE SOUND CONTROL check box REV:1.0 NOTES: 70 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Press the TRIP tab and: -‐ Set the CAR TYPE to 26 -‐ This setng should have already been set correctly from factory. Press the X on the upper right of the screen and cycle the igni>on. REV:1.0 NOTES: 71 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Test the NavigaDon From the HOME screen, look for a map icon as shown If you have this HOME screen, press this icon instead. REV:1.0 NOTES: 72 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Upon the first Naviga>on sorware boot-‐up, configure the basic Regional parameters… -‐ -‐ -‐ -‐ -‐ -‐ Select Imperial values for the United States (MPH, MPH, etc…) Select Metric values for Canada (KM/h, KM/l, etc..) Select the preferred language Select the system voice preference Tick YES for all YES or NO ques>ons. One completed, you will end to the below screen Check if you have full GPS signal strength under clear sky Press this window and jump to the next page… REV:1.0 NOTES: 73 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Press here to access the naviga>on Quick Menu Adjust the naviga>on voice output with the slider at around 75% of the scale. This is usually enough for the instruc>ons to be heard clearly. REV:1.0 NOTES: 74 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual From the naviga>on HOME screen or the MAP screen, look for the “Q” le]er. The system Quick Menu will appear to show the system available func>ons. Select the appropriate func>on to test the following: Prior final assembly, test the following: -‐ Radio mode (TRIP): FM, XM, USB, AUX, CD Steering Wheel Controls and Voice Commands, etc… ALL func>ons supported by the factory radio must work. -‐ Facia keypad hard keys, volume control and power. -‐ Naviga>on: Check for GPS recep>on (at least configure the basic setngs on start-‐up) -‐ MP3 Player: See if you can select music from the File folder (refer to User Manual. Connect a USB thumb drive to the External Media box prior tes>ng) Once completed, you can proceed with the final assembly. Put back the remaining trim pieces. REV:1.0 NOTES: 75 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual YOU DID IT! REV:1.0 NOTES: 76 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Appendix 1 Reverse Camera Connec>on to the head unit REV:1.0 NOTES: 77 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual A]ach the RED wire from MAIN I/O 1 “REAR PWR” to the backup camera RED wire and isolate with electrical tape. Plug the back up camera RCA jack into the same Yellow Camera jack of MAIN 1/O 1 and secure with electrical tape. REV:1.0 NOTES: 78 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Reserve the BLACK wire round terminal from MAIN I/O 1 “REAR PWR” to the radio front bo]om screw as shown (Ground) when the radio will be in it’s loca>on and secured . Go back to page 63… REV:1.0 NOTES: 79 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Appendix 2 Parking Assist REV:1.0 NOTES: 80 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Plug the Parking Assist connector into the car’s OBD located right underneath the driver crash pad in the middle. Once inserted, lock it in place by moving the yellow tab un>l you hear a “click”. Note: Please advise your dealer about this sensor and how to proceed to remove it. REV:1.0 NOTES: 81 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Insert into the “CAN” Posi>on Reserve to be connected to the Trip Module as shown at final assembly. Go back to page 63… REV:1.0 NOTES: 82 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Appendix 3 RDS Traffic Tuner REV:1.0 NOTES: 83 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Connect the female TMC FM adapter to the car’s male. FM RDS TMC Connect the male TMC FM adapter to the back of the radio. Reserve the cable labeled TMC of the MAIN I/O 2 for the final assembly. Go back to page 63… REV:1.0 NOTES: 84 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Appendix 4 iR Remote Control REV:1.0 NOTES: 85 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Go back to page 63… REV:1.0 NOTES: 86 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Appendix 5 Troubleshoo>ng REV:1.0 NOTES: 87 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Symtom TRIP Board (radio interface) Cause TRIP DLL loading failed Car type selec>on is wrong TRIP Board (Audio Interface) is not connected Flat ribbon damage Trip module failure Car type selec>on is wrong Fix Select appropriate Car type (Setng / TRIP / CAR TYPE) Refer to the install manual Ribbon cable was damaged, replace Replace trip module No power to the radio (No flashing led inside the trip module) TRIP Serial not connected at the trip module (Flashing led inside the trip module) TRIP Serial not connected to MAIN I/O 1 cable label TRIP SERIAL (Flashing led inside the trip module) Improperly seated flat ribbon (No flashinbg led inside the trip module) Damaged flat ribbon (contact ma>ng surface damaged) Defec>ve TRIP module (no flashing led inside trip module Select appropriate Car type (Setng / TRIP / CAR TYPE) Refer to the install manual Check Audio patch cord properly seated at radio and car side also check AUDIO & MEMORY fuses Connect TRIP serial connector (5 pin) to trip module Connect TRIP Serial connector (3 pin) to MAIN I/O 1 TRIP Serial Seat properly flat ribbon as per manual Replace flat ribbon Replace trip module Control Keypad (for equipped models) Keypad not working Keypad not connected to trip module Damaged cable (pinched or cut wires) Trip board interface problem Trip board interface problem Connect keypad to trip module Replace cable Check TRIP Board Symptom above Check ribbon cable System not boo>ng with blank screen but trip module is flashing Check power connector at the screen Improper connec>ons on MAIN I/O 1 Screen failure. Replace screen Check Audio Patch cord check also check AUDIO & MEMORY fuses NAND Flash corrupted. Replace screen Check External media box connec>on (SD Card / USB box) Screen No power at the screen only No power at screen and radio System not fully boo>ng Screen is responding to touch but applica>ons are not star>ng Screen is not responding to touch Steering Wheel controls System not boo>ng with blank screen and trip module not flashing Boot Progress bar is stopping Applica>ons icons are sensed (changing color) but not star>ng SD Card is corrupted Screen is not responding to keypress Steering wheel controls are not working Audio steering wheel controls are not working REV:1.0 Screen is out of calibra>on. Touch and hold for 10 seconds the screen to enter into the calibra>on sequence Check if TRIP module GREEN and BLUE wires (2 pin) are connected to the AUDIO T-‐ HARNESS cord Check Audio patch cord 2 pin connector NOTES: 88 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual Symtom Sound Naviga>on sound is weak thru the mini speaker No Naviga>on sound thru the mini speaker Cause Fix (Mini speaker is required for all installs) Compass-‐NAV system sound is routed to the car speakers only when the factory radio is set to AUX otherwise sound is routed to the mini speaker Volume controls are too low Volume controls are too low Mini speaker not connected or defec>ve Go into the system SETTING / VOLUME and adjust to the recommended levels Go into the system SETTING / VOLUME and adjust to the recommended levels Check connec>on of the mini speaker System Clock System date and >me is many years back System clock is off by few hours only System >me has not been updated by the GPS sorware GPS sorware Time Zone is incorrect Start the naviga>on applica>on to sync the date and >me Start the naviga>on applica>on and go to MORE / SETTINGS / REGIONAL and select TIME ZONE. Tick the box AUTO System can't read the SD Card Check if the SD Card is properly seated Clean SD Card contact with Alcohol SD Card corrupted by improper ejec>on method Check External media box connec>on (SD Card / USB box) NavigaDon Can't find executable file REV:1.0 NOTES: 89 Model: Hyundai Santa Fe standard audio system Kit number: CNM5-‐DM1-‐8 Year range: 2013-‐UP CN-‐M5 Installa>on manual END REV:1.0 NOTES: 90