Detailing Manual v7

Transcription

Detailing Manual v7

POLISHING, WAXING & EXTERIOR DRESSING
Introducing the
3M Automotive
Detailing System
A Complete System that Includes Cleaners,
Dressings, Polishes, Waxes and more.
Long the standard of quality and the preferred paint
finishing system among automotive professionals, 3M offers
a Detailing System for expanded customer
satisfaction, increased worker safety, environmental
compliance and product value.
This state-of-the-art system incorporates several safer
products, technological advancements for excellent
results, easy dispensing systems and other innovations
to achieve the ultimate in detailing system performance.
This complete line is the only system you need to
deliver quality detailed vehicles for expanded
customer satisfaction.
3M™ Detailing System …
“For the Life of Your Car”
3Detailing System
Table of Contents
SAFETY STATEMENT
3
INSPECT AND PRE-CLEAN
4
HEAVY CLEANING
6
EXTERIOR CLEANING
8
POLISHING, BUFFING, WAXING & EXTERIOR DRESSING
10
INTERIOR CLEANING
12
FINAL INSPECTION CHECKLIST
14
BODY SHOP CLEAN-UP GUIDE
15
PAINT FINISHING DO’S AND DON’TS
17
PAINT REPAIR PROCEDURE
19
DILUTION RATIOS
21
DILUTER USAGE – Installation / Troubleshooting
23
PRODUCT INFORMATION
27
DETAILING FINAL EXAM
43
ORDERING INFORMATION
45
SAFETY STATEMENT
SAFETY STATEMENT
3M Detailing Products Safety Statement
Read and understand all safety information before using this product.
Wear appropriate personal
protective equipment to include:
Boots
•
Chemical resistant gloves
•
Aprons
•
Eye protection
•
No loose fitting clothing or articles that may be caught in moving parts
•
Avoid belts with buckles that may damage painted surfaces
•
Avoid sharp objects that may damage leather or fabric upholstery
WARNING
CAUTION
Before handling or using detailing chemicals, be sure to read
the Material Safety Data Sheet (MSDS) for health hazard
data, precautionary information, and suggested first aid.
Eye irritation -- wear eye protection when dispensing
solutions and when replacing concentrate bottle solutions.
Skin irritation -- wear rubber gloves when dispensing
WARNING
Fire hazard.
CAUTION
Window Cleaner concentrate solution is flammable.
Eye hazard.
Flying particles and dust.
Wear safety glasses with side shields when
drilling or hammering.
Keep away from open flame; no smoking nearby.
Consult local regulation for VOC compliance.
3
3M™ Automotive Reconditioning Guide
INSPECT & PRE-CLEAN
Inspect the vehicle. Note any adhesive residue, tree sap, or bug spatters that will need to be specially treated. Use
air blower to remove leaves from trunk jambs and engine cowlings. Check for loose or missing caps on power
1. ansteering,
power brakes, oil filler, etc.; tighten or replace if necessary. Remove all trash from interior including trunk,
ashtray, and seat folds. Inspect the interior carpet and fabric upholstery for any stains or heavily soiled areas that will
require pre-spotting.
any stained or heavily soiled interior carpet or fabric upholstery surfaces using 3M™ All Purpose Cleaner
2. Pre-spot
and Degreaser, diluted at 1:15 (1 part concentrate plus 15 parts water) and brush lightly. Pre-spotting and brushing
greatly enhances the effectiveness of the cleaner and reduces the time needed to remove the stains later in the process.
4
INSPECT & PRE-CLEAN
Heavy Duty Wheel Cleaner to the wheels. Use the following steps to achieve maximum performance:
3. ApplyStep3M™1: Determine
which concentration to use based on experience.
- Use a 1:2 dilution for lightly soiled wheels (1 part concentrate plus 2 parts water)
- Use 100% concentrate for heavily soiled wheels (undiluted).
Step 2: Spray 3M™ Heavy Duty Wheel Cleaner onto a DRY wheel. Pre-rinsing the wheel dilutes the product,
reducing its effectiveness.
DO NOT use 3M™ Heavy Duty Wheel Cleaner on glass, engines, anodized wheels and/or wheels with no
coating or with coating cracked or in poor condition. Glass that is stained by the 3M™ Heavy Duty Wheel
Cleaner can not be repaired and will need to be replaced.
Note: 3M™ Heavy Duty Wheel Cleaner does not contain hydrofluoric or other strong acids.
4. Apply 3M™ All Purpose Cleaner and Degreaser, diluted at 1:15 (1 part concentrate plus 15 parts water), to the
engine and engine compartment (lightly), tires, wheels, wheel wells, rocker panels, door and trunk jams, etc. Let
stand for 1 to 2 minutes. Rinse or wipe down engine and engine compartment surfaces with towel.
Note: 3M™ Heavy Duty Wheel Cleaner works best on brake dust, while 3M™ All Purpose Cleaner and Degreaser
works best on other soils. For best results, use both products on wheels.
5
HEAVY CLEANING
HEAVY CLEANING
tires, wheels, and other heavily soiled areas as necessary. A medium stiffness bristled brush works best on
1. Scrub
tires and most wheels, however, for chrome wheels, a wash mitt or terry cloth towel often produces better results.
rinse all of the exterior areas where 3M™ Heavy Duty Wheel Cleaner and/or 3M™ All Purpose Cleaner
2. Thoroughly
and Degreaser have been applied. Rinse or wipe down engine and engine compartment last.
Do not spray or rinse water on sensitive electrical engine components.
Note: It is recommended that you start the engine when rinsing or spraying
the engine compartment with water.
6
HEAVY CLEANING
HEAVY CLEANING
(CONTINUED)
any adhesive residue from the vehicle’s exterior surfaces using 3M™ Adhesive Remover with a towel or
3. Remove
scrub pad. No longer available for sale in California. Suggested replacement: 3M™ General Purpose Adhesive
Cleaner (PN 08984 or PN 08987).
7
EXTERIOR CLEANING
EXTERIOR CLEANING
3M™ All Purpose Cleaner and Degreaser, diluted at 1:15 (1 part concentrate plus 15 parts water) onto
1. Apply
any bug spatters.
the vehicle using 3M™ Car Wash Soap diluted at 1:100 (1 part concentrate plus 100 parts water) and a clean,
2. Wash
soft, sponge, towel, wash mitt or 3M™ Detail Cloth. Start at the top and work downward, scrubbing the areas with
bug spatters last.
Note: 3M™ Car Wash Soap cleans effectively at a 1 to 100 dilution ratio. Increasing the concentration will increase
the suds but will also be more difficult to rinse off.
8
EXTERIOR CLEANING
EXTERIOR CLEANING
(CONTINUED)
step (if needed or necessary): Clay the vehicle as needed with 3M™ Perfect-It™ III Cleaner Clay using the
3. Optional
diluted 3M™ Car Wash Soap as a lubricant. This step may also be done after the vehicle is dry using 3M™
Perfect-It™ Gloss Enhancer as a lubricant.
4. Rinse the entire vehicle thoroughly and dry using a chamois or a clean, soft, cotton terry cloth towel.
Optional step if needed or necessary: Remove any tree sap deposits on glass surfaces using 3M™ Glass Cleaner
and a terry cloth towel. Inspect vehicle after wash to identify any tree sap or similar deposits that were
5. undiluted
not removed by washing.
9
Least
05954 / 05955
05973 / 05974
38105
05928 / 05929
38116
38133
38111
39030 / 38112
Coarse
Finish
Most
Aggressiveness
Fine
Buffing Pad
Characteristics
Most
Least
05703
05719
05704
05705
05713
05723
05725
Coarse
Finish
- Swirls and fine scratches:
Step 1. Polish using 3M™ Detail Polish 108 with a 3M™ Perfect-It™ Foam
Polishing Pad, PN 05725.
Step 2. Wax.
- Oxidation and medium scratches:
Step 1. Polish using 3M™ Detail Polish 208 with a 3M™ Superbuff™ Polishing
Pad, PN 05705.
Step 3. Wax.
- Heavy oxidation and coarse scratches:
Step 1. Compound using 3M™ Detail Compound 308 with a 3M™ Superbuff™ III
2 Plus 2 Buffing Pad, PN 05704.
Step 3. Wax.
Polishing materials:
- 3M™ Detail Compound 308 = fastest cut / coarsest finish
- 3M™ Detail Polish 208
= less cut / finer finish
- 3M™ Detail Polish 108
= least cut / finest finish
Polishing pads:
- 3M™ Superbuff™ III 2 Plus 2 Buffing Pad, PN 05704 = fastest cut / coarsest finish
- 3M™ Superbuff™ Polishing Pad, PN 05705
= less cut / finer finish
- 3M™ Perfect-It™ Foam Compounding Pad, PN 05723 = less cut / finer finish
- 3M™ Perfect-It™ Foam Polishing Pad, PN 05725
= least cut / finest finish
Compound / Polish
Characteristics
Aggressiveness
as needed using the following guidelines:
1. Polish
Recommended polishing steps:
Fine
10
POLISHING, BUFFING, WAXING &
EXTERIOR DRESSING
POLISHING, BUFFING, WAXING &
EXTERIOR DRESSING
(CONTINUED)
Wax the painted surfaces using 3M™ Detail Wax or 3M™ Perfect-It™
Car Paste Wax or 3M™ Performance Finish for best results:
2. Show
Step 1. Apply a thin, uniform coating of wax or 3M™ Performance
Finish. Allow Detail Wax or Paste Wax to dry to a haze.
Step 2. Remove wax residue using a soft, cotton terry cloth towel.
Step 3. Detail using a 3M™ Perfect-It™ Detailing Cloth.
the tires using 3M™ Tire Dressing or 3M™ Silicone Free Tire
3. Dress
Dressing. Apply a thin, uniform coating to a clean, dry tire using a
sprayer or applicator pad. The level of gloss can be controlled by the
thickness of of the coating.
DO NOT USE 3M™ Tire Dressing or 3M™ Silicone Free Tire
Dressing on motorcycles, bicycles, or other two-wheeled vehicles’
tires or seats. Avoid spraying onto brake rotors, brake drums or
brake pedals.
3M™ Silicone Free
Tire Dressing
Note: Allow 3M™ Silicone Free
Tire Dressing to completely dry
before driving vehicle as sling
(particularly from newer tires)
may stain painted surfaces.
3M™ Tire Dressing
11
3M™ PERFORMANCE FINISH FOR
BEST RESULTS
DIRECTIONS FOR USE
Do not apply in direct sunlight or
onto a hot surface. Wash and dry
vehicle using 3M™ Car
Wash Soap (PN 39000).
If paint is dull or oxidized
use 3M™ One Step
Cleaner Wax (PN 39006)
after washing the vehicle,
but prior to using 3M™
Performance Finish.
HAND
Step 1. Gently apply a thin, uniform
film to the paint surface using a terry
cloth wax applicator or a clean, soft,
folded cotton terry cloth towel.
Step 2. Remove residue and buff to a
high gloss using a 3M™ Microfiber
Detail Cloth (PN 39016) or a clean,
soft, cotton terry cloth towel.
Step 3. Complete method one panel
at a time.
MACHINE
Step 1. Apply a thin, uniform film to
the paint surface using a random
orbital polisher equipped with a clean,
soft, terry cloth bonnet or DA
equipped with a soft foam pad.
Step 2. Buff to a high gloss with a
polisher equipped with a clean, dry,
terry cloth bonnet or by hand using a
3M™ Microfiber Detail Cloth
(PN 39016) or a clean, soft, cotton
terry cloth towel.
Step 3. Complete method one panel
at a time.
INTERIOR CLEANING
INTERIOR CLEANING
Clean the interior vinyl, plastic, leather, and rubber surfaces using 3M™ All Purpose Cleaner and Degreaser, diluted
1:30 (1 part concentrate plus 30 parts water) and a towel or brush. Dry the surface using a clean, dry terry cloth
1. attowel.
Use an air blower with the towel for hard to reach places.
Note: For cleaning heavily soiled vinyl or leather upholstery, use 3M™ All Purpose Cleaner and Degreaser, diluted at 1:15
(1 part concentrate plus 15 parts water).
clean the vehicle’s carpet and upholstery using an extraction machine with 3M™ All Purpose Cleaner and
2. Thoroughly
Degreaser diluted at 1:100).
12
INTERIOR CLEANING
INTERIOR CLEANING
(CONTINUED)
the vehicles interior vinyl, plastic, leather, and rubber components using 3M™ Interior Dressing. Apply enough
3. Dress
dressing to achieve a uniform wet appearance. Wipe off excess dressing using a clean, soft, dry terry cloth towel.
Note: - For a lower gloss, dilute 3M™ Interior Dressing 1:1 with water (1 part concentrate plus 1 part water).
- For a higher gloss, use 3M™ Engine and Tire Dressing undiluted.
the vehicle’s windows using 3M™ Premium Glass Cleaner diluted at 1:14 (1 part concentrate plus 14 parts
4. Clean
water) and a clean, soft, dry cotton terry cloth towel.
CAUTION: DO NOT USE UNDILUTED 3M™ GLASS CLEANER ON INTERIOR VEHICLE SURFACES.THE
CONCENTRATED PRODUCT WILL STAIN VINYL AND LEATHER, AND MAY STAIN OTHER SURFACES.
Note: - In hot, humid weather conditions spray and clean one window at a time
- Use 3M™ Glass Cleaner concentrate undiluted for removing tree sap from exterior windows.
inspect the vehicle exterior. Use a 3M™ Perfect-It™ Detailing Cloth and/or 3M™ Perfect-It™ Gloss
5. Thoroughly
Enhancer for final detailing.
13
FINAL INSPECTION CHECKLIST
3M Customer Pre-Delivery
Detailing Checklist
Pre-Delivery Cleaning and Final Inspection:
q Inspect the vehicle
q Adhesive residue, tree sap, bug spatters
q Leaves, debris in jambs and cowlings
q Loose or missing caps, tighten or replace
q Remove all trash from interior including trunk, ashtray, and seat folds
q Note stains or heavily soiled carpet or upholstery
q Pre-spot and brush stained or heavily soiled areas
q Clean wheels and wheel wells
q Clean engine
q Removed tar and/or adhesive residue
q Wash vehicle
q Clay vehicle if needed
q Removed tree sap if needed
q Buff and wax vehicle
q Compound removal from jambs, moldings, etc.
q Dress tires
q Interior cleaning:
q Removed all items from interior
q Vacuum all surfaces
q Presoak carpet and upholstery stains
q Scrub stained areas with brush
q Finish cleaning carpet and upholstery
q Clean all interior surfaces, vinyl, leather
q Dress all interior surfaces
q Clean interior and exterior glass
q Replaced all items in vehicle
q Final exterior inspection
Responsibility:
______________
______________
______________
______________
______________
______________
______________
______________
______________
______________
______________
______________
______________
______________
______________
______________
______________
______________
______________
______________
______________
14
BODY SHOP CLEAN-UP SYSTEM
3M™ Body Shop Clean-Up
SYSTEM GUIDE
1. Inspect vehicle
2. Pre-Spot heavily soiled interior spots with APC
STEP 2
HD Wheel Cleaner (Do not use on glass, engines, anodized wheels and/or
3. Apply
wheels with no coating or with coating cracked or in poor condition.)
- 3M™ Heavy Duty Wheel Cleaner (PN 38374/38375)
STEP 3
APC & Degreaser to engine compartment, wheels, tires, jams, etc...
4. Apply- 3M™
All-Purpose Cleaner & Degreaser (PN 38350/38351/38052)
STEP 4
5. Brush tires/wheels as needed
6. Rinse APC & Degreaser
tape or adhesive residue with GPAC or Adhesive Remover
7. Remove
- 3M™ General Purpose Adhesive Cleaner (PN 08984/08986/08987)
- 3M™ Adhesive Remover (PN 38080/38081/38082)
STEP 7
bugs and/or compound residue with APC & Degreaser
8. Pre-soak
- 3M™ All-Purpose Cleaner & Degreaser (PN 38350/38351/38052)
STEP 8
15
BODY SHOP CLEAN-UP SYSTEM
vehicle with Car Wash Soap
9. Wash- total
3M™ Car Wash Soap (PN 38377/38378/38079)
STEP 9
10. Clay paint overspray as required
11. Rinse and dry
STEP 10
tree sap from glass with undiluted Glass Cleaner as required
12. Remove
- 3M™ Glass Cleaner (PN 38399/38300/38101)
Final Glaze to fresh painted areas
13. Apply- 3M™
Perfect-It™ 3000 Final Glaze (PN 06067/06066)
tires with Silicone-Free Tire Dressing
14. Dress- 3M™
Silicone-Free Tire Dressing (PN 38327/38328)
STEP 14
STEP 15
interior with APC & Degreaser
15. Clean- 3M™
All-Purpose Cleaner & Degreaser
(PN 38350/38351/38052)
STEP 16
interior and exterior windows with Glass Cleaner
16. Clean- 3M™
Glass Cleaner (PN 38399/38300/38101)
with Detail Cloth and inspect
17. Wipe-vehicle
3M™ Detail Cloth (PN 06016/06017/06018)
18. Attach mirror hang tag with shop business card
16
PAINT FINISHING DO’S AND DON’TS
Paint Finishing Do’s & Don’ts
1. Sanding Step
DRY
OR
4. Polishing Step
WET
• Removes defects such as deep scratches, dust nibs or
excessive orange peel
• Dry sand with Dual Action Sander, foam interface pad
recommended for contours OR wet sand by hand
Caution: Sanding through clear coat will require repainting
• Follow with Scratch Refinement Step and/or
Compounding Step
2. Scratch Refinement Step
• Damp sand with 3M™ Trizact™ disc on Dual Action Sander
• Use foam interface pad for contours
• Produces Semi-polished finish
• Follow with Compounding Step
3. Compounding Step
• Removes imperfections, such as car wash scratches,
medium to coarse scratches, medium oxidation and stains
• Use wool pad for faster and more aggressive cutting
• Use foam pad for slower and finer cutting
• Follow with Polishing Step
17
• Removes swirls, fine scratches and very mild stains
• For Dark Colors use finer polish and finer foam pads
• For Lighter Colors use more aggressive polish and foam pads
• Note: Swirls and imperfections remaining after this step
will reoccur after waxing step products wash or wear off
• Follow with Waxing Step
5. Waxing Step
• Waxing fills swirls, very minor scratches and imperfections
by leaving a thin layer of wax protection
• Wax does little to further refine paint after the polishing
step. After wax is washed or worn away, the imperfections remaining after polishing will reappear
• Apply a thin even coat
• Apply by hand on a damp pad
• Apply with a Dual Action Sander using:
05729 3M™ Perfect-it™ Foam Polishing D/A Pad - 6 in.
05739 3M™ Perfect-it™ Hookit II Foam D/A Glazing Pad
05732 3M™ Perfect-it™ Hookit™ II DA Foam
Application Pad - 6 in.
While polishing and waxing a vehicle, you may have
noticed that some fine scratches became less visible or
even disappeared, only to reappear after the vehicle has
been washed a few times. By using the correct system of
products and procedures, many small paint defects can
be removed and will not reappear when the polish and
wax are washed and worn away.
To remove a defect from the paint surface, you must
remove the very thin layer of paint that contains the
defect by spending enough time with a compound or polish.
By removing this thin layer of paint, you actually remove
the defect. See Illustration 1.
Some scratches, acid rain pits, or other more severe
defects may not be able to be removed completely. If a
defect goes too deep into the clear coat, sanding to the
bottom of the defect may result in inadequate clear coat
thickness, or may even require a repaint. See Illustration 2.
Generally speaking, if you can feel a scratch with your
fingernail, you should not attempt to remove it completely.
However, even without sanding, many deep scratches or
other more severe defects that are compounded, polished
and waxed will be less noticeable.
3M™ Perfect-It™
Foam Pad
CORRECT
3M™ Perfect-It™
Foam Pad
INCORRECT
3M™ Superbuff™
Buffing Pad
CORRECT
3M™ Superbuff™
Buffing Pad
INCORRECT
3M™ Perfect-It™ Foam Pads
Instructions for Use:
Recommended speed — 1500 to 2000 R.P.M. Do not
exceed 3000 R.P.M. Use only with 3M™ Hookit™
SBS™ Backup Pad, PN 05717 or a 3M™ Perfect-It™
Backup Pad, PN 05718.
To Install:
1. Center the compound pad on the backup pad.
2. Press firmly and twist to insure good contact with
backup pad.
IMPORTANT:
Use caution around trim or moldings to avoid snagging
or tearing the pad. Keep the pad flat, or nearly flat,
on surface being compounded.
To minimize the possibility of burning, reduce pressure
over sharp convex/concave areas such as detail lines,
fenders, etc. and keep surface wet with compound.
3M Foam Pad Care and Cleaning Instructions:
If pad becomes clogged, remove and install a clean
pad. Clean clogged pad as follows:
1. Rinse in warm (up to 115˚F) water.
2. Set wet pad face up on a flat surface and allow
to dry.
IMPORTANT:
Rinse under water faucet. Do not use soap or cleaning
solvents. Do not machine wash or dry. Do not clean
pads with a buffing spur or screwdriver.
3M™ Superbuff™ III Buffing Pad
(double-sided wool pad)
CAUTION:
3M™ Superbuff™ III Buffing Pad can spin off air-driven
polishers due to tool’s rapid stop. To avoid spin off,
firmly tighten buff onto adapter. Use 7/8 in. wrench
to hold adapter while tightening buff.
Buffing Pad Care and Cleaning Instructions:
Periodically rake pad with buffing spur or air nozzle
to remove excess rubbing compound or glaze. If pad
becomes clogged, remove, turn over, reinstall and
continue buffing, allowing used side to dry. Washing
pad causes shrinkage of wool fibers. If washing is
desired, use only cool (60–80˚F) water. Do not use
hot water, strong detergents or solvents. Use washing
machines with gentle agitation only. Machine drying
is not recommended.
18
BUFFING DO’S AND DON’TS
Hiding vs. Removing
Paint Defects
Paint Condition
Sanding & Scratch
Refinement
Diagnosis
New or Like New
Virtually no imperfections
Swirls and Very
Fine Scratches
Scratches / Swirls / Imperfections
Visible only in sunlight
Heavy Swirls
Fine Scratches
Mild Stains
Light Oxidation
Imperfections that can be seen in
shade or fluorescent lighting, but
appear as swirls in sunlight. This
procedure is usually done on light
to medium colored cars only.
Medium Scratches
Car Wash Scratches
Heavy Stains
Medium Oxidation
Imperfections easily seen in shade
or fluorescent lighting. Scratches
can usually be seen separate from
swirls in sunlight.
Coarse Scratches
Heavy Oxidation
Imperfections easily seen in all
lighting. Can usually be seen from
some distance.
Deep Scratches
Excessive Overspray
Scratches plainly seen– may have
a white look. May be felt with a
fingernail, but only very slightly.
3M™ Trizact™
Hookit™ II Foam Discs
02075
1
Very Deep Scratches
Scratches felt with a fingernail.
BE CAREFUL! Abrasive removal of too
much clear coat or sanding into base
color coat may require repainting.
3M™ Hookit™ II
Finishing Film Discs
-or3M™ Imperial™
Wetordry™ Paper
Sheets
00850
02021
2
TIP: When in doubt, use finer system first and
then use more aggressive system as required
19
TIP: Buffing pads in compounding step are
listed most aggressive to finer finishing
1
Repair Procedure
Compounding
Polishing
Waxing
3M™ Detail Wax
-or3M™ Perfect-It™ Show
Car Paste Wax
-or3M™ Performance
Finish
-and3M™ Perfect-It™
III Detailing Cloths
05725
3M™ Detail Polish #108
-and05751
3M™ Perfect-It™ Foam
Polishing Pad
-or3M™ Perfect-It™ 3000
Ultrafina™ SE
-and3M™ Perfect-It™ Ultrafina™
Foam Polishing Pad
5
-and3M™ Perfect-It™ Foam
Compounding Pad- 8 in.
38133
06068
05723 38116
3M™ Detail Wax
Car Paste Wax
Finish
3M™ Detail Wax
Car Paste Wax
-or3M™ Performance Finish
-and3M™ Perfect-It™ III
Detailing Cloths
06016
06017
39526
38111
38112
4
06016
06017
39526
38111
38112
4
06016
06017
39526
Polishing Pad
Ultrafina™ SE
Ultrafina™ Foam
Polishing Pad
38105
5
3
5
3M™ Perfect-It™ II Rubbing Compound
-and3M™ Perfect-It™ III 05719 05973
05703
Compounding Pad
05704
-or3M™ Superbuff™ III
Buffing Pad
-or3M™ Superbuff™ III 2 Plus 2
Buffing Pad
3
5
5
05719 38105
3M™ Detail Compound #308
05703
-and3M™ Perfect-It™ III Compounding Pad 05704
05723
-or3M™ Superbuff™ III Buffing Pad
3
Buffing Pad
-or3M™ Perfect-It™ Foam Compounding Pad- 8 in.
5
1– Use Disc Pad PN 05251 (on DA Sander) and Optional
Interface Pad PN 05274 or by hand with Pad PN 05291
4
3M™ Detail Wax
06016
-or06017
3M™ Perfect-It™ Show 39526
Car Paste Wax
-or3M™ Performance Finish
-and3M™ Perfect-It™ III
Detailing Cloths
4
05725 38133
-and05751 06068
Polishing Pad
Ultrafina™ SE
5
Foam Polishing Pad
05725 38133
05751 06068
Polishing Pad
Ultrafina™ SE
Foam Polishing Pad
5
2– Use 3M™ No.20 Sponge Pad PN 05526
3– Use with Superbuff Adapter PN 05710 and PN 05718
4
38111
38112
5
05725 38133
-and05751 06068
Polishing Pad
Ultrafina™ SE
Foam Polishing Pad
5
05719 05704
05703 05723
38105
-and3M™ Perfect-It™ III Compounding Pad
-or3
Buffing Pad
-or3M™ Perfect-It™ Foam Compounding Pad- 8 in.
05725 38133
05751 06068
4
38111
38112
5
-and05719
3M™ Perfect-It™ III
05703
Compounding Pad
05704
-or3M™ Superbuff™ III 05723
Buffing Pad
-or3M™ Superbuff™ III
2 Plus 2 Buffing Pad
-or3M™ Perfect-It™
Foam
Compounding
Pad- 8 in.
4
4
38111
38112
3M™ Detail Wax
Car Paste Wax
Finish
06016
06017
39526
3M™ Detail Wax
Car Paste Wax
Finish
06016 38111
06017 38112
39526
3M™ Detail Wax
06016 38111
-or06017 38112
3M™ Perfect-It™ Show 39526
Car Paste Wax
Finish
4
4
4
4
4
4
4– For Dual Action Sander Application use Pad PN 05251 and Pad PN 05739 or PN 05732
5– Use with PN 05718 or PN 05717
20
DILUTION RATIOS
Product Dilution Ratios Explained
Mix water-based chemicals with water to make ready-to-use products.
Why
- Safer for workers
- Save money buying concentrates
- Ratios pre-set to match the job
- Better for the environment
Dilution examples
- 1:3 or one-to-three = 1 part concentrate + 3 parts water = 4 gallons of useable product
- 1:15 or one-to-fifteen = 1 part concentrate + 15 parts water = 16 gallons of useable product
Cost per gallon example
- 1:4 = 1 part concentrate ($5.00) + 4 parts water ($0.00) = $5.00 for 5 gallons or $1.00 per useable gallon
3M dilution suggestions
See below
21
SPRAY BOTTLE
AUTOMATIC DILUTER
BULK CONCENTRATE
Label Mix
Diluter Pre-mix
Shop Mix
DILUTER USAGE
3M™ Detailing Product Diluter
INSTALLATION & USE INSTRUCTIONS
Read and understand all safety information before using this product.
Intended Use
The 3M Detailing Product Diluter is intended to be used to dilute and dispense selected water based 3M Detailing
Products. The diluter is designed to operate on typical city water supply pressures.
Miscellaneous Diluter and Accessory Parts
• Available from Shopware Inc.
Phone # 1-800-877-9344
Fax # 952-392-2018 for order form
• Other accessories parts/service available
• Shopware part numbers below
• Pay via Visa, MasterCard or American Express
Part Number
PD100
PD101
PD102
PD103
Description
Diluter tip kit (5 kits with 14 sizes)
synthetic rubber foot valve (blue color 5/kit)
PD104
PD105
PD106
Diluter (PN 37711) selector switch
Glass cleaner foot valve (gray color 5/kit)
Rieke Spout Spigot (for 5 gallon round and
one gallon plastic 2/kit)
Male NPT Spigot (for 5 gallon cubes 2/kit)
Utility funnel (16oz. 3/kit)
Glass Cleaner in-line valve (gray color 3/kit)
5-Shelf Stack Rack (for 5-gallon cubes;
black color) Price includes shipping
and handling.
Conversion kit (PN 37712) to Glass Cleaner
PD107
PD108
PD109
PD110
PD111
In-line check valve (blue color 3/kit)
Pickup tube kit (1 tube, 3 weights, 3
synthetic rubber foot valve)
Safety Information
WARNING
Before handling or using detailing chemicals, be sure to
read the Material Safety Data Sheet (MSDS) for health
hazard data, precautionary information, and suggested
first aid.
WARNING
Fire hazard.
Window Cleaner concentrate solution is flammable.
Keep away from open flame; no smoking nearby.
CAUTION
Eye irritation -- wear eye protection when dispensing
Skin irritation -- wear rubber gloves when dispensing
CAUTION
Eye hazard. Flying particles and dust.
Wear safety glasses with side shields
when drilling or hammering.
22
DILUTER USAGE
INSTALLATION & USE INSTRUCTIONS
(CONTINUED)
Installing the Diluter
1. Open the carton and check contents.
- The carton contains the diluter control console with attached concentrate supply tubes and dispenser tubes.
- Also, there is a small bag that contains one spare bottle cap, mounting screws, and wall anchors.
2. Remove the front cover from the control console.
- Press in on the tabs on both sides of the control console and simultaneously lift the front panel off.
3. Mark the location of 3 mounting screws on the wall.
- Position the back plate of the control console against the wall at the desired location. (You may use a level to make sure
the control console is straight, but this is not critical to operation.)
- Mark the location of the mounting screws with a pen or pencil. There are two keyholes at the top of the plate and a slot
hole near the bottom, left side.
CAUTION
Eye hazard.
Flying particles and dust.
Wear safety glasses with side shields when drilling or hammering.
4. Drill holes for screws.
- Use a 5/16” drill bit to make holes for the 3 wall anchors. You may need to use a masonry drill bit for some types of wall.
5. Insert wall anchors.
- Hammer the anchors flush to the wall.
6. Insert top two screws
- Screw in the top two screws, but leave the heads out about 1/4” from the wall.
- Do not install the third screw yet.
7. Secure the backplate to the wall
- Do not over tighten the screws.
- Place the console backplate on the wall. The keyholes at the top should fit over the two screw heads in the wall and slip
down into the keyhole notches.
- Install the bottom screw and then tighten all three screws.
8. Attach the water supply.
- Thread the end of a standard garden hose to the connector on the right side of the control console (as you face the unit).
- Note: The cap on the connector on the left side (as you face the unit) should normally remain in place.
IMPORTANT
Inspect to be sure the tubes are attached securely. The tube for
supplying glass cleaner concentrate to the diluter is a special tube and
must be used for the glass cleaner concentrate. Do not switch tubes.
9. Snap the front cover into place.
- Press in on the two side tabs while pushing the cover on until it snaps into place.
10. Arrange concentrate containers below diluter so hoses are neatly arranged.
- Each supply tube has a label on it to identify the concentrate product it supplies.
- Insert each concentrate supply tube into its correct concentrate container and fasten the lid.
23
DILUTER USAGE
IMPORTANT
Make sure the supply tubes are inserted into their correct
concentrate product containers.
Using the Diluter
Dispense Heavy Duty Wheel Cleaner:
- Place a correctly labeled detailing spray bottle onto the corresponding product tube coming out the bottom of the
diluter console.
- Press and hold correct button until bottle is filled.
Dispense Glass Cleaner or All Purpose Cleaner & Degreaser:
- Place a correctly labeled detailing spray bottle onto the corresponding product tube coming out the bottom of the
diluter console.
- Press and hold correct button until bottle is filled.
Dispense Car Wash Soap:
- The long tube on the right bottom of the console is for dispensing soap into a bucket on the floor.
Place the end of the tube in a bucket.
- Press and hold the right button, labeled Car Wash Soap, until you’ve dispensed the amount you want.
The chart above shows the dilution ratios of water to various 3M detailing products. The eductor, labeled at the top,
can be brown, grey, or yellow. The eductor is the part in the assembly that the hoses attach to. Find your eductor color and look below it to find the product you are using. In the column below your product, you will
see various dilution ratios. Find your ratio and follow it left to determine which dilution tip color you
will use. Example: Brown eductor with a black dilution tip has a dilution ratio of 1:2 of 3M™
Heavy Duty Wheel Cleaner to water.
Depending on your hose fitting size you may have a snap tip or a threaded tip. If you
are using a threaded dilution tip, it is important that you screw hand tight plus a
1/4 turn. If you are using a snap dilution tip, fully insert it into the barbed
fitting (be sure not to squeeze the tip).
**Requires 3M™ Diluter Conversion Kit for Glass Cleaner
(PD111) (Shopware 1-800-877-9344)
24
DILUTER USAGE
TROUBLESHOOTING GUIDE
PROBLEM:
SOLUTION:
Excessive foam in 3M™ Heavy Duty Wheel Cleaner (when
filling, bottle is more than 1/2 full of foam)
Tighten the fitting where the 3M™ Heavy Duty Wheel
Cleaner suction hose meets the diluter
3M™ Car Wash Soap not sudsy enough
Replace yellow orifice tip with brown, orange or green
orifice tip
No siphon on select product(s)
Ensure all fittings are very tight and secure. Replace foot valve
on the end of the hose. Ensure adequate water pressure
Water leaks where garden hose attaches to diluter
Ensure rubber washer is inside fitting. Tighten the fitting
Water leaks where gray water hose fitting meets white
valve housing
Unscrew gray fitting, reapply thread sealer/tape, screw
fitting back in
After use, suction hose drains down or loses prime
Replace foot valve on the end of the hose. Note: Use gray
foot valve for 3M™ Glass Cleaner and a blue foot valve for
all other products.
While in use, water “spits out” from gray or yellow eductor
Mineral deposits inside eductor misdirecting water flow;
remove eductor and soak/clean with lime-away type
product and reinstall.**
After usage, solid crystals develop in 3M™ Glass Cleaner
supply hose
Remove supply hose, clean out crystals, and reinstall or
replace selector switch or install separate 3M™ Single
Product Diluter PN 37712 with Glass Cleaner Conversion
Kit PD111 (Available from Shopware 1-800-877-9344)
After usage, residue builds up around and inside selector
switch causing difficult operation or reduced suction*
Replace selector switch or disassemble and clean selector
switch with water. Note: Pay attention to how the switch
comes apart for exact re-assembly
25
DILUTER USAGE
PROBLEM:
SOLUTION:
No discharge
a. Open water supply.
b. Install valve parts kit.
c. Install regulator if water pressure exceeds 60 PSI (flowing).
d. Clean** or replace.
No concentrate draw
a. Clean or replace.
b. Clean (descale)** or replace.
c. Minimum 20 PSI (with water running) required to operate
unit properly.
d. Push tube firmly onto eductor discharge hose barb; be
sure inner discharge tube is installed and has flooding ring.
e. Replace with full container.
f. Tighten, but do not overtighten.
g. Disconnect inlet water line and clean strainer.
Excess concentrate draw
a. Press correct tip firmly into barb on eductor.
b. Place concentrate below the eductor.
Failure of unit to turn off
a. Clean** or replace with valve parts kit.
b. Make sure magnet moves freely.
c. Remove button and clean cabinet/button to remove any
dirt lodged in slide recess
Excess foaming in discharge
a. Put clamp on tube or replace tube if brittle.
b. Install inner discharge tube.
Water discharge from air vents on eductor
a. Be sure discharge tube is not immersed, kinked or
elevated. Be sure there is no liquid in the discharge tube
when beginning to operate dispenser.
b. Install pressure regulator if flowing water pressure
exceeds 60 PSI (flowing).
* Applies only to old model with selection switch (37711)
** In hard water areas, scale may form inside the discharge end of the eductor, as well as in other areas of the unit that are
exposed to water. This scale may be removed by soaking the eductor in a descaling solution (deliming solution). To
remove an eductor located in the cabinet, firmly grasp water valve and unthread eductor. Replace in same manner.
Alternatively, a scaled eductor can be cleaned (or kept from scaling) by drawing the descaling solution through the unit.
Operate the unit with the suction tube in the descaling solution. Operate the unit until solution is drawn consistently, then
flush the unit by drawing clear water through it for a minute. Replace concentrate container and put suction tube
into concentrate.
26
PRODUCT INFORMATION
PAINT
SHOP
SAFE!
3M™ Heavy Duty Wheel Cleaner
A water based cleaner concentrate for removing brake dust from
vehicle wheels. Does not contain hydrofluoric or other strong acids.
- PN 38374 (38074)*
- PN 38375 (38075)*
- PN 38076
1 gallon bottle
5 gallon pail
55 gallon drum
3M™ Heavy Duty Wheel Cleaner is a cleaner concentrate designed
to remove tough brake dust deposits from wheels.
Directions for Use:
1. Add 1 part cleaner concentrate to 2 parts water.
2. Apply 3M™ Heavy Duty Wheel Cleaner to vehicle wheels and
let stand for about 2 minutes.
Note: 3M™ Heavy Duty Wheel Cleaner works best when
applied to a dry wheel.
3. Apply 3M™ All Purpose Cleaner and Degreaser (1:15 dilution)
to the tires and wheels. Let stand for approximately
one minute.*
4. Rinse thoroughly, using a high-pressure washer.
5. For particularly stubborn brake dust deposits, use 3M™ Heavy Duty Wheel Cleaner undiluted.
*Note: 3M™ Heavy Duty Wheel Cleaner works best for removing brake dust, while 3M™ All Purpose Cleaner and
Degreaser works best for cleaning tires and removing other difficult soils from wheels.
DO NOT use 3M™ Heavy Duty Wheel Cleaner on glass, engines, anodized wheels and/or wheels with no
coating or with coating cracked or in poor condition. Glass that is stained by the 3M™ Heavy Duty Wheel
Cleaner can not be repaired and will need to be replaced.
Note: 3M™ Heavy Duty Wheel Cleaner does not contain hydrofluoric or other strong acids.
Tips:
- For heavy brake dust deposits agitation with a brush greatly enhances cleaning effectiveness.
- Light agitation on some chrome wheels greatly enhances the final appearance.
- For removing water spots, apply 3M™ Heavy Duty Wheel Cleaner diluted at 1 part cleaner concentrate to 2 parts
water to the vehicles painted surfaces, let stand two minutes but do not allow to dry, scrub using a terry cloth towel
and rinse.
Product Safety and Health Information Source:
Material Safety Data Sheet
(MSDS 08-3012-5) or
3M Automotive Aftermarket Division
3M Center, Bldg. 223-6N-01
St. Paul, MN 55144-1000
Telephone: 1-877-MMM-CARS (1-877-666-2277) or (651) 737-6501
* Part number to be discontinued
27
PRODUCT INFORMATION
PAINT
SHOP
SAFE!
3M™ All Purpose Cleaner and Degreaser
A water based cleaner/degreaser concentrate for exterior and interior
vehicle cleaning.
- PN 38350 (38050)*
- PN 38351 (38051)*
- PN 38052
1 gallon bottle
5 gallon pail
55 gallon drum
3M™ All Purpose Cleaner and Degreaser is a heavy duty cleaner
concentrate designed for both interior and exterior vehicle cleaning
applications. 3M™ All Purpose Cleaner and Degreaser removes oil,
grease, and other tough soils from vehicle engines, tires, wheels, and other
heavily soiled exterior vehicle surfaces, and is very effective for removing
insect residue from the fronts of vehicles. 3M™ All Purpose Cleaner and
Degreaser also cleans and removes soils and most stains from carpet,
fabric upholstery, vinyl, leather, and other interior vehicle surfaces.
Directions for Use:
DILUTION – 1:15 (Add 1 cup concentrate to a gallon container
and fill with water.) Use for degreasing, tire and wheel cleaning,
insect residue removal, carpet and upholstery stain removal, and
other heavy duty cleaning applications.
DILUTION – 1:30 (Add 1/2 cup concentrate to a gallon container and fill with water.) Use for cleaning vinyl, leather,
plastic and other lightly soiled vehicle surfaces.
Degreasing/Insect Residue Removal: (1:15 dilution)
1. Spray diluted cleaner onto heavily soiled areas – engines, tires, wheels, insect residue, etc. Let stand about 2 minutes.
2. Scrub/brush heavily soiled areas as needed.
3. Rinse thoroughly using a high pressure washer.
Carpet/Fabric Upholstery Cleaning (1:15 dilution)
1. Spray diluted cleaner directly onto the surface.
2. Work the surface using the appropriate sponge, cloth, or brush.
3. Remove soil using an extraction unit.
Vinyl/Leather – Light Duty Cleaning (1:30 dilution)
1. Spray the diluted cleaner directly onto the surface, or spray onto a terry cloth towel and apply.
2. Work the surface using the appropriate sponge, cloth, or brush.
3. Remove soil using a clean, dry terry cloth towel.
Tips:
- For maximum effectiveness do not allow degreaser to dry before rinsing.
- For heavily soiled wheels; first apply 3M™ Heavy Duty Wheel Cleaner, soak two minutes, then apply
3M™ All Purpose Cleaner and Degreaser (1:15 dilution), soak one minute, scrub as needed and rinse.
Material Safety Data Sheet (MSDS 16-3418-7) or
St. Paul, MN 55144-1000
Telephone: 1-877-MMM-CARS (1-877-666-2277)
or (651) 737-6501
28
PRODUCT INFORMATION
PAINT
SHOP
SAFE!
3M™ Glass Cleaner
A solvent based water dilutable cleaner concentrate.
- PN 38399 (38099)*
- PN 38300 (38100)*
- PN 38101
1 gallon can
5 gallon pail
55 gallon drum
(special order)
3M™ Glass Cleaner is a concentrated cleaner that quickly and
effectively removes smoke films, fingerprints and other soils from
windows and plastic surfaces, and may also be used to assist in the
removal of window stickers and adhesive residue. 3M™ Glass
Cleaner does not contain ammonia and will not leave a filmy residue.
Directions for Use:
CAUTION: DO NOT USE UNDILUTED 3M™ GLASS CLEANER
ON INTERIOR VEHICLE SURFACES. THE CONCENTRATED
PRODUCT WILL STAIN VINYL AND LEATHER, AND MAY STAIN
OTHER SURFACES.
CAUTION: DO NOT USE 3M™ GLASS CLEANER ON FRESHLY
PAINTED SURFACES.
1. Add 1 part concentrate to 14 parts water (add 1 cup to 1 gallon of water).
2. Spray onto the glass or plastic surface and rub thoroughly using a clean, soft, dry cotton terry cloth towel.
3. Remove the final material with a clean, soft, dry terry cloth towel.
Tips:
- To ensure optimum performance, always use fluorinated 3M™ Detailing Spray Bottles with 3M™ Glass Cleaner.
- In hot, humid weather conditions spray one window at a time and wipe immediately.
(MSDS 08-2999-4) or
St. Paul, MN 55144-1000
29
PRODUCT INFORMATION
PAINT
SHOP
SAFE!
3M™ Premium Glass Cleaner
A solvent based water dilutable cleaner concentrate.
Excellent for high humidity conditions.
- PN 38221
- PN 38222
1 gallon can
5 gallon pail
Directions for Use:
CAUTION: DO NOT USE UNDILUTED 3M™ GLASS CLEANER
ON INTERIOR VEHICLE SURFACES.
THE CONCENTRATED PRODUCT WILL STAIN VINYL AND
LEATHER, AND MAY STAIN OTHER SURFACES.
CAUTION: DO NOT USE 3M™ GLASS CLEANER ON FRESHLY
PAINTED SURFACES.
1. Add 1 part concentrate to 14 parts water (add 1 cup to 1 gallon of water).
2. Spray onto the glass or plastic surface and rub thoroughly
using a clean, soft, dry cotton terry cloth towel.
3. Remove the final material with a clean, soft, dry terry cloth
towel.
Tips:
- To ensure optimum performance, always use fluorinated 3M™ Detailing Spray Bottles with 3M™ Glass Cleaner.
- In hot, humid weather conditions spray one window at a time and wipe immediately.
(MSDS 08-2999-4) or
St. Paul, MN 55144-1000
30
PRODUCT INFORMATION
PAINT
SHOP
SAFE!
3M™ Car Wash Soap
A highly concentrated water based soap.
- PN 38377 (38077)*
- PN 38378 (38078)*
- PN 38079
1 gallon bottle
5 gallon pail
55 gallon drum
3M™ Car Wash Soap is a highly concentrated liquid soap which
develops heavy-bodied, long-lasting suds and quickly removes dirt
and road film from exterior automotive surfaces.
Directions for Use:
1. Add 1 part soap concentrate to 100 parts water in a clean
bucket (about 2/3 cup in five gallons water).
2. Rinse the vehicle thoroughly to remove any grit that could
scratch the paint surface.
3. Wash the vehicle using a clean, soft, sponge, towel or
wash mitt.
4. Rinse thoroughly and dry using a clean, soft, cotton terry
cloth towel or chamois.
(MSDS 08-3014-1) or
St. Paul, MN 55144-1000
31
PRODUCT INFORMATION
PAINT
SHOP
SAFE!
3M™ Adhesive Remover*
A solvent based product that quickly removes adhesive residue.
- PN 38080
- PN 38081
- PN 38082
1 gallon can
5 gallon pail
55 gallon drum
3M™ Adhesive Remover is a ready-to-use blend of petroleum solvents designed to remove adhesive deposits from exterior vehicle
surfaces. To minimize the possibility of staining, do not apply in
direct sunlight or onto a hot surface.
Directions for Use:
1. Soak cloth with 3M™ Adhesive Remover and apply onto
the surface.
2. Rub thoroughly with a soft cloth and remove the excess
material with a clean, dry, soft cloth. Repeat as necessary.
3. For stubborn deposits, apply material, allow to soak for one
minute and scrub.
Tips:
- For difficult oil-based stains on fabric apply 3M™ Adhesive Remover, scrub, and clean using 3M™ All Purpose Cleaner
and Degreaser or 3M™ Multi-Purpose Cleaner.
- Use 3M™ Premium Glass Cleaner concentrate undiluted for removing tree sap from exterior windows.
(MSDS 08-4315-1) or
St. Paul, MN 55144-1000
*Not for sale in California. Suggested replacement: 3M™ General Purpose Adhesive Cleaner (PN 08984 or 08986 or 08987)
32
PRODUCT INFORMATION
3M™ Interior Dressing
A ready-to-use water based silicone dressing.
- PN 38086
- PN 38087
1 gallon bottle
5 gallon pail
3M™ Interior Dressing is a ready-to-use water-based silicone
emulsion designed to restore a natural gloss appearance to all vinyl,
leather, rubber and plastic interior vehicle surfaces.
Directions for Use:
1. Spray onto a clean, soft, cotton terry cloth towel and wipe onto
the surface, or spray directly onto the surface and wipe. Use
enough material to achieve a uniform appearance.
2. Wipe off excess material using a clean, soft, dry terry cloth
towel to achieve a natural look and feel.
Tips:
- For a lower gloss dilute 3M™ Interior Dressing 1:1 with water.
- For a higher gloss use 3M™ Engine and Tire Dressing undiluted.
(MSDS 08-3134-7) or
St. Paul, MN 55144-1000
33
PRODUCT INFORMA-
3M™ Engine and Tire Dressing
A water based silicone engine and tire dressing concentrate.
- PN 38124
- PN 38125
- PN 38126
1 gallon bottle
5 gallon pail
55 gallon drum
3M™ Engine and Tire Dressing is a water-based silicone emulsion
concentrate, designed to restore a deep black appearance on tires,
hoses and rubber moldings, and a clean new look on vinyl, plastic,
and other low gloss or flat painted surfaces.
Directions for Use:
1. For dressing engines, add 1 part concentrate to 1 part water;
or for dressing tires, apply concentrate.
2. Apply a uniform coating directly onto the surface and allow to
dry naturally.
Tips:
- For higher gloss, use 3M™ Engine Dressing undiluted.
- Great tire dressing where low VOC’s are required.
- 3M™ Engine and Tire Dressing may be used undiluted as a tire dressing or an interior dressing:
1. Apply a uniform coating to the surface.
2. Remove excess using a terry cloth towel.
(MSDS 08-6460-3) or
St. Paul, MN 55144-1000
34
PRODUCT INFORMATION
3M™ Tire Dressing
A solvent based ready-to-use silicone tire dressing.
- PN 38127
- PN 38128
- PN 38129
1 gallon can
5 gallon pail
55 gallon drum
3M™ Tire Dressing is a solvent based silicone dressing that
produces a deep black, glossy appearance on new and nearly new
tires, and a deep black, natural appearance on older tires.
Directions for Use:
1. Spray a thin, uniform coating onto a clean, dry tire. Wipe
lightly with a clean, soft, terry cloth towel and allow to dry.
2. Remove overspray from wheels, hubcaps, or painted surfaces
using a clean, soft dry terry cloth towel.
DO NOT USE on motorcycles, bicycles, or other two-wheeled
vehicles’ tires or seats. Avoid spraying onto brake rotors,
brake drums or brake pedals.
Tips:
- For a higher gloss appearance apply dressing and allow to dry without wiping.
- For lower VOC requirements use 3M™ Engine and Tire Dressing (see page 34.)
(MSDS 08-6461-1) or
St. Paul, MN 55144-1000
35
PRODUCT INFORMATION
PAINT
SHOP
SAFE!
3M™ Silicone Free Tire Dressing
A solvent based, ready-to-use silicone free tire dressing.
- PN 38327 (38227)*
- PN 38328 (38228)*
1 gallon can
5 gallon pail
3M™ Silicone Free Tire Dressing is a solvent based silicone free
dressing that produces a deep black, glossy appearance on new and
nearly new tires, and a deep black, natural appearance on older tires.
It is critical to follow the directions for use for 3M™ Silicone Free
Tire Dressing to avoid the possibility of paint staining.
Directions for Use:
Note: Sling from some, particularly newer, tires may
stain painted surfaces. To avoid staining, follow these
instructions carefully.
1. Clean tires thoroughly using 3M™ All Purpose Cleaner and
Degreaser 1:15 or stronger and scrub using a stiff bristle brush.
2. Thoroughly rinse the tires using a pressure washer and allow
to dry.
3. Apply a thin, uniform coating of 3M™ Silicone Free Tire Dressing using a trigger sprayer, sponge applicator, or rag.
Note: Use only a thin coating of dressing. A heavy coating may puddle around tire treads or raised lettering, and spatter
even after the dressing dries.
4. Remove excess dressing using an absorbent cloth.
5. Allow dressing to dry completely before driving the vehicle.
DO NOT USE on motorcycles, bicycles, or other two-wheeled vehicles’ tires or seats.
Avoid spraying onto brake rotors, brake drums or brake pedals.
(MSDS 16-2924-5) or
St. Paul, MN 55144-1000
or (651) 737-6501
* Part Number To Be Discontinued
36
PRODUCT INFORMATION
PAINT
SHOP
SAFE!
3M™ Perfect-It™ III Cleaner Clay
A clay bar for removing overspray and environmental contaminates
from a vehicle’s exterior surfaces.
- PN 38070
200 gram bar
3M™ Perfect-It™ III Cleaner Clay is recommended for use in
removing contaminants such as rail dust, paint overspray, and
industrial fallout from exterior paint, glass, and metal surfaces.
Directions for Use:
Do not use in direct sunlight or on a hot surface.
1. Wash and rinse vehicle thoroughly using 3M™ Car Wash Soap.
2. Check exterior surfaces for contaminants – a rough or gritty feel.
3. Work contaminated areas with the clay using light pressure and 3M™ Car Wash Soap or 3M™ Perfect-It™ Gloss
Enhancer as a lubricant.
4. Rinse and dry surface.
5. Knead clay periodically to expose a new surface.
Tips:
- Use 3M™ Perfect-It™ III Cleaner Clay with 3M™ Car Wash Soap as a lubricant while washing the vehicle, or use 3M™
Perfect-It™ III Cleaner Clay with 3M™ Perfect-It™ Gloss Enhancer (contains silicone) as a lubricant after the vehicle
has been washed.
(MSDS 08-5407-5) or
St. Paul, MN 55144-1000
37
PRODUCT INFORMATION
3M™ Detail Polish 108
A light cutting very fine finishing polish. Contains silicones.
- PN 38133
1 gallon bottle
3M™ Detail Polish 108 is a light cutting, very fine finishing polish
recommended for use to remove light oxidation, fine scratches and
stains, and leaves an excellent, high gloss finish on all types of
automotive paints. To minimize the possibility of staining, do not
apply in direct sunlight or onto a hot surface.
Note: Contains silicones. Not recommended for use in body shop or
paint shop applications.
Directions for Use:
Polish using an electric buffer (1000 to 2500 RPM) equipped with
a 3M™ Superbuff™ Polishing Pad or a 3M™ Perfect-It™ Foam
Polishing Pad.
1. Shake container before using.
2. Apply enough polish to the paint surface to work a 2’ x 2’
area. To minimize slinging, spread the polish over the surface
with the pad before starting the machine.
3. Start the machine and buff using light-to-medium pressure.
4. Reduce pressure as polish begins to dry, and buff to a high gloss. Clean pad as necessary to assist cleanup.
Tips:
Excellent for the first step of a 2-step buffing procedure.
Step 1 – Use 3M™ Detail Compound 308 with a 3M™ Superbuff™ Compounding Pad to remove imperfections such as
heavy oxidation, car wash scratches or other coarse scratches.
Step 2 – Use 3M™ Detail Polish 208 with a 3M™ Perfect-It™ Foam Polishing Pad to remove the compound swirl
marks and product the best finish.
(MSDS 08-5425-7) or
St. Paul, MN 55144-1000
38
PRODUCT INFORMATION
3M™ Detail Polish 208
A medium cutting fine finishing polish. Contains silicones.
- PN 38116
1 gallon bottle
3M™ Detail Polish 208 is a medium cutting, fine finishing polish
recommended for use to remove oxidation, scratches and stains,
and leaves a high gloss finish on all types of automotive paints. To
minimize the possibility of staining, do not apply in direct sunlight or
onto a hot surface.
Directions for Use:
Polish using an electric buffer (1000 to 2500 RPM) equipped with
a 3M™ Superbuff™ Polishing Pad or a 3M™ Perfect-It™ Foam
Compounding Pad.
2. Apply enough polish to the paint surface to work a 2’ x 2’ area.
To minimize slinging, spread the polish over the surface with
the pad before starting the machine.
3. Start the machine and buff using light-to-medium pressure.
4. Reduce pressure as polish begins to dry, and buff to a high gloss. Clean pad as necessary to assist cleanup.
Tips:
Excellent for use with a 3M™ Perfect-It™ Foam Compounding Pad to remove light oxidation, fine scratches, and stains
and leaves a high gloss finish in a one step process.
(MSDS 09-0268-4) or
St. Paul, MN 55144-1000
39
PRODUCT INFORMATION
3M™ Detail Compound 308
A medium cutting fine finishing compound. Contains silicones.
- PN 38105
1 gallon bottle
3M™ Detail Compound 308 is a medium cutting, fine finishing
compound recommended for use to remove heavy oxidation, coarse
scratches and stains, and leaves a medium gloss, fine swirl mark
finish on all types of automotive paints. To minimize the possibility of
staining, do not apply in direct sunlight or onto a hot surface.
Directions for Use:
Compound using an electric buffer (1000 to 2500 RPM)
equipped with a 3M™ Superbuff™ Compounding Pad, or a
3M™ Perfect-It™ Foam Compounding Pad.
2. Apply enough compound to the paint surface to work a 2’x2’
area. To minimize slinging, spread the compound over the
surface with the pad before starting the machine.
3. Start the machine and buff using light to medium pressure.
4. Reduce pressure as the compound begins to dry. Clean pad as necessary to assist cleanup.
Tips:
Excellent for the first step of a 2-step buffing procedure.
Step 1 – Use 3M™ Detail Compound 308 with a 3M™ Superbuff™ Compounding Pad to remove imperfections such as
heavy oxidation, car wash scratches or other coarse scratches.
Step 2 – Use 3M™ Detail Polish 208 with a 3M™ Perfect-It™ Foam Polishing Pad to remove the compound swirl
marks and product the best finish
(MSDS 09-6468-4) or
St. Paul, MN 55144-1000
40
PRODUCT INFORMATION
3M™ Detail Wax
A carnauba wax based durable liquid wax. Contains silicones.
- PN 38111
1 gallon
3M™ Detail Wax is an easy to use, durable automotive wax
recommended for use on new or like new paint finishes to produce
a deep, high gloss, lustrous finish. To minimize the possibility of
staining, do not apply in direct sunlight or onto a hot surface.
Directions for Use:
1. Apply a thin, uniform coating of wax to the paint surface, either
by hand or with an orbital action tool equipped with a foam pad.
Allow to dry to a haze.
2. Remove wax residue and buff to a high gloss using a soft,
cotton terry cloth towel.
(MSDS 09-2788-9) or
St. Paul, MN 55144-1000
3M™ Perfect-It™ Gloss Enhancer
A water based spray detailing product. Contains silicones.
- PN 38113
- PN 38114
- PN 38115
1 gallon bottle
5 gallon pail
55 gallon drum (special order)
3M™ Perfect-It™ Gloss Enhancer is a quick and easy, “spray on /
wipe off” product that can restore a just waxed look and feel. 3M™
Perfect-It™ Gloss Enhancer is also recommended for use as a spray
detailing product to assist in the removal of buffing residue, and as a
lubricant for claying a vehicle.
Directions for Use:
Do not apply in direct sunlight or onto a hot surface.
1. Shake well before using.
2. Remove any grit that could scratch the paint surface.
3. Spray on and wipe off small areas – one panel at a time.
4. Remove any dried overspray with a damp cloth.
41
PRODUCT INFORMATION
(CONTINUED)
Tips:
- For a clay lubricant, use enough 3M™ Perfect-It™ Gloss Enhancer to completely wet the surface. After claying, wipe
off the residue before it dries.
(MSDS 08-3020-8) or
St. Paul, MN 55144-1000
3M™ Performance Finish
A reactive silicone paint protector. Contains silicones.
- PN 38112
- PN 39030
quart bottle
pint bottle
3M™ Performance Finish is a reactive silicone based product that
bonds to the paint surface providing a durable, long
lasting and high gloss protective finish with exceptional water
beading qualities. The application and removal characteristics make
this product extremely easy to use leaving a high gloss wet look finish that is pleasing to the eye. It’s more than a wax!
Directions for Use:
1. Apply a thin, uniform film to the paint surface, using a terry
cloth wax applicator or a clean, soft, folded, cotton, terry cloth
towel. Or use a random orbital polisher equipped with a clean,
soft, terry cloth bonnet or DA equipped with soft
foam pad.
2. Remove residue and buff to a high gloss using a 3M™ Microfiber Detail Cloth (PN 39016) or a clean,
soft, cotton terry cloth towel. Or, with a polisher equipped with a clean, dry, terry cloth bonnet.
3. Complete method one panel at a time.
(MSDS 18-5336-5) or
St. Paul, MN 55144-1000
or (651) 737-6501
42
Detailing Final Exam
Duty Wheel Cleaner will (may) cause damage on:
1. 3M™a. Heavy
Uncoated wheels or coated wheels in poor condition
2.
3.
4.
5.
6.
43
b. Glass
c. Engines
d. All of the Above
The two recommended dilution ratios for 3M™ All Purpose Cleaner & Degreaser are:
a. 1:15 and 1:25
b. 1:12 and 1:25
c. 1:15 and 1:30
d. 1:10 and 1:20
e. 1:8 and 1:16
Which of the following is a concern or a potential problem when buffing with a foam pad?
a. Easy to use
b. Runs hotter
c. No lint
d. Minimal swirls
e. None of the above
What product would you use to remove a coffee stain from a carpeted floor mat?
a. 3M™ All Purpose Cleaner & Degreaser diluted 1:30
b. 3M™All Purpose Cleaner & Degreaser diluted 1:15
c. 3M™ Heavy Duty Wheel Cleaner
d. 3M™ Gloss Enhancer
What product would you recommend for removing hard water spots from a painted or plastic surface?
a. 3M™ Heavy Duty Wheel Cleaner diluted 1:2 (Do not use on glass, engines, anodized wheels and/or
b. 3M™ All Purpose Cleaner & Degreaser diluted 1:15
c. 3M™ Heavy Duty Wheel Cleaner undiluted (Do not use on glass, engines, anodized wheels and/or wheels
with no coating or with coating cracked or in poor condition.)
d. 3M™ All Purpose Cleaner & Degreaser diluted 1:30
If a product is diluted 1:8 and costs $18 per gallon, what is the cost per diluted gallon?
a. $2.25
b. $2.00
c. $1.75
d. $1.50
is diluted 1:15 and costs $24 per gallon, what is the cost per diluted gallon?
7. If a product
a. $2.25
8.
9.
10.
11.
12.
13.
14.
15.
b. $2.00
c. $1.75
d. $1.50
Silicones are not recommended for use in a body shop environment:
q T
q F
3M™ Detail Polish 108 cuts more than 3M™ Detail Compound 308:
q T
q F
The recommended product for removing tar from a painted surface is:
c. 3M™ Heavy Duty Wheel Cleaner undiluted (Do not use on glass, engines, anodized wheels and/or
The recommended product for removing bug spatters is:
c. 3M™ Heavy Duty Wheel Cleaner undiluted (Do not use on glass, engines, anodized wheels and/or
When detailing a vehicle, it is recommended to begin washing it from the bottom because that is the dirtiest part:
q T
q F
The polishes and compounds can or may be used with wool pads:
q T
q F
There is no difference between 3M™ Heavy Duty Wheel Cleaner and competitive wheel cleaners:
q T
q F
Trizact™ Abrasive Discs must always be used damp:
q T
q F
44
ANSWERS: 1. d 2. c 3. b 4. b 5. a 6. b 7. d
8. T 9. F 10. e 11. b 12. F 13. T 14. F 15. T
Ordering Information
Exterior Cleaners
Part
No.
| Product
| Name
| Container
| Size
| Cont.
| Per Case
38350
38351
38052
38070
38374
38375
38076
38377
38378
38079
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3M™ All Purpose Cleaner & Degreaser (38050)*
3M™ All Purpose Cleaner & Degreaser
3M™ Perfect-It™ III Cleaner Clay
3M™ Heavy Duty Wheel Cleaner (38074)*
3M™ Heavy Duty Wheel Cleaner (38075)*
3M™ Car Wash Soap (38077)*
3M™ Car Wash Soap (38078)*
3M™ Car Wash Soap
Gallon
5-Gallon Pail
55-Gallon Drum
1 Jar
Gallon
5-Gallon Pail
55-Gallon Drum
Gallon
5-Gallon Pail
55-Gallon Drum
4
1
1
6
4
1
1
4
1
1
Exterior Cleaners (Solvents)
Part
No.
| Product
| Name
38080 | 3M™ Adhesive Remover
| Container
| Size
| Cont.
| Per Case
| Gallon
|
| 5-Gallon Pail
|
| 55-Gallon Drum |
4
1
1
Exterior Dressings
Part
No.
| Product
| Name
| Container
| Size
| Cont.
| Per Case
38124
38125
38126
38127
38128
38129
38327
38328
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3M™ Tire Dressing
3M™ Tire Dressing
3M™ Tire Dressing
3M™ Silicone Free Tire Dressing (38227)*
3M™ Silicone Free Tire Dressing (38228)*
45
Gallon
5-Gallon Pail
55-Gallon Drum
Gallon
5-Gallon Pail
55-Gallon Drum
Gallon
5-Gallon Pail
4
1
1
4
1
1
4
1
Interior Cleaners
Part
No.
| Product
| Name
| Container
| Size
| Cont.
| Per Case
38350
38351
38052
38095
38399
38300
38101
38221
38222
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3M™ All Purpose Cleaner & Degreaser
3M™ Extraction Cleaner* (See 38350)
3M™ Glass Cleaner (38099)*
3M™ Glass Cleaner (38100)*
3M™ Glass Cleaner
Gallon
5-Gallon Pail
55-Gallon Drum
Gallon
Gallon
5-Gallon Pail
55-Gallon Drum
Gallon
5-Gallon Pail
4
1
1
4
4
1
1
4
1
Interior Dressing
Part
No.
| Product
| Name
38086 | 3M™ Interior Dressing
38087 | 3M™ Interior Dressing
| Container
| Size
| Cont.
| Per Case
| Gallon
| 5-Gallon Pail
|
|
4
1
Waxes, Polishes & Compounds
Part
No.
| Product
| Name
| Container
| Size
| Cont.
| Per Case
38105
38111
38113
38114
38115
38116
38133
38112
39030
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3M™ Detail Wax
Gallon
Gallon
Gallon
5-Gallon Pail
55-Gallon Drum
Gallon
Gallon
Quart
Pint
4
4
4
1
1
4
4
6
6
Detailing Accessories
Part
No.
| Product
| Name
37721
37712
37716
37717
37718
37720
|
|
|
|
|
|
3M™ Detailing Diluter– Single Product
3M™ Detailing Spray Bottle
3M™ Detailing GP Spray Nozzle
3M™ Detailing Solvent Spray Nozzle
3M™ Detailing Squeeze Bottle
| Container
| Size
|
|
|
|
|
|
1 Diluter
1 Diluter
1 Bottle
1 Spray Head
1 Spray Head
1 Bottle & Top
| Cont.
| Per Case
|
|
|
|
|
|
1
1
24
24
24
24
Note: For Diluter Service Parts, contact Shopware, Inc. 1-800-877-9344
46
(CONTINUED)
Sanding
Part
No.
| Product
| Name
| Grade
|
| Sheets or | Quantity
| Pads/Box | Per Case
00850
00868
02023
02044
02045
02075
05274
05251
05291
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3M™ Hookit™ II Finishing Film
3M™ Hookit™ II Finishing Film
3M™ Imperial™ Wetordry™ Paper Sheets
3M™ Trizact™ Hookit™ II Foam Disc 6”
3M™ Hookit™ II Soft Interface Pad
3M™ Hookit™ II Disc Pad
3M™ Hookit™ II Hand Pad 6”
P1500
P1200
Micro Fine 1500
Micro Fine 2000
Micro Fine 2500
P3000
Pad
Painters Pad
Pad
50
50
50
50
50
15
6” Pad
6” Pad
6” Pad
|
|
|
|
|
|
|
|
|
4
4
5
5
5
4
10
10
10
Compounding Pads
47
Part
No.
| Product
| Name
| Items
| Per Unit
| Quantity
| Per Case
05703
05704
05710
05717
05718
05719
05723
05737
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3M™ Superbuff™ III 2 Plus 2 Buffing Pad
3M™ Superbuff™ adapter
3M™ Hookit™ SBS™ Backup Pad
3M™ Perfect-It™ Backup Pad
3M™ Perfect-It™ III Compounding Pad
3M™ Perfect-It™ Foam Compounding Pad
3M™ Perfect-It™ Plus Foam Compounding Pad
Pad
Pad
adapter
Pad
Pad
Pad
2 Pads/Bag
1 Pad/Bag
6
6
10
1
1
24
12
6
Polishing Pads
Part
No.
| Product
| Name
05717
05718
05733
05751
05725
05729
05739
05732
05738
|
|
|
|
|
|
|
|
|
| Items
| Per Unit
3M™ Hookit™ SBS™ Backup Pad
| Pad
3M™ Perfect-It™ Backup Pad
| Pad
3M™ Perfect-It™ Plus Ultrafina™ Foam Polishing Pad - 8” I 1 Pad/Bag
I 2 Pads/Bag
3M™ Perfect-It™ Ultrafina™ Foam Polishing Pad - 8”
3M™ Perfect-It™ Foam Polishing Pad
| 2 Pads/Bag
3M™ Perfect-It™ Foam Polishing D/A Pad - 6”
| 2 Pads/Bag
3M™ Perfect-It™ Hookit™ II Foam D/A Glazing Pad | 2 Pads/Bag
3M™ Perfect-It™ Hookit™ II DA Foam Application Pad - 6” I 2 Pads/Bag
3M™ Perfect-It™ Plus Foam Polishing Pad
| Pad
| Quantity
| Per Case
|
|
|
|
|
|
|
|
|
1
1
6
6
6
12
12
12
6
Detail Cloths
Part
No.
| Product
| Name
06016 | 3M™ Perfect-It™ Detail Cloths
06017 | 3M™ Perfect-It™ Detail Cloths – Bulk
06018 | 3M™ Perfect-It™ Jumbo Detail Cloths
| Items
| Per Unit
| Quantity
| Per Case
| 6 Cloths/Bag
| 50 Cloths/Bag
| 6 Cloths/Bag
|
|
|
6
1
6
48
(CONTINUED)
Spray Bottle Labels
60Number
| Product
| Name
| Labels Per Pack*
60-4400-7328-0
60-4400-7329-8
60-4400-9926-9
60-4400-9925-1
60-4400-7339-7
60-4400-7576-4
60-4400-7346-2
60-4400-7341-3
60-4400-7331-4
60-4400-7343-9
60-4400-7340-5
60-4400-8404-8
60-4400-7344-7
60-4400-7332-2
60-4400-7614-3
60-4400-7345-4
60-4400-7342-1
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3M™ Heavy Duty Wheel Cleaner/Concentrate
3M™ All Purpose Cleaner and Degreaser HD 1:15
3M™ All Purpose Cleaner and Degreaser LD 1:30
3M™ Glass Cleaner
3M™ Car Wash Soap
3M™ Adhesive Remover
3M™ Interior Dressing
3M™ Tire Dressing
3M™ Silicone Free Tire Dressing
3M™ Detail Wax
3M™ Gloss Enhancer
*Please Order Per Pack
Contact a 3M sales representative for more information:
St. Paul, MN 55144-1000
or (651) 737-6501
49
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
50
3
Automotive Aftermarket Division
3M Center, Building 223-6N-01
St. Paul, MN 55144-1000
www.3M.com/automotive
3M is a trademark of 3M
© 3M 2007
All rights reserved
60-4400-9939-2

Detailing Manual v7

Transcription

Similar documents

thix watch

Fingerprint Pad

Be Girl Pad Features

Stera Sheen and Urn Clean

ACTION® OrIgINAl TAble PAds - Action Products Action Products

HOTTIES

Lot 17 Altivole Drive, Edenbrook Estate, Norville

Google Earth Instructions: 1. Open the Passage Fish Passage

Hardwood Floor Cleaner

PLS 24 PRO Poron XRD Info Sheet