turbo series

ROTARY CUTTERS
ROTARY CUTTERS
TURBO SERIES
Cutting Width
Transport Width
Overall Width
Overall Length
Cutting Height
Blade Overlap
Hitch: Lift
Pull
Semi Mount(Hyd. Offset)
Blade Carriers (Cross-Braced)
Tractor HP Required (Min.):
Lift (with adequate front weight)
Pull
Semi-Mount
Gearbox Rating: Center
Outboard
Output Shaft Diameter (Outboard)
Blade Tip Speed: 540 RPM
1000 RPM
Cutting Capacity (Max. Diameter)
Driveline Size
Deck Thickness (Turbo Dome™)
Upper Sheet
Lower Sheet
Side Skirts
Replaceable Skid Shoes
Safety Deflectors
Transport Latch: Pull or Semi-Mount
Weight (Approx.) Lift
Pull
Semi-Mount
STANDARD EQUIPMENT AND
SPECIFICATIONS
TURBO 96
TURBO 120
97”
104”
104”
101” Lift, Semi Mount
136” Pull
1-1/2” – 12”
4”
CAT II-III Q.H.
Clevis
Cat II (Offsets 11” Left/Right)
Round Pan
120”
127”
127”
117” Lift, Semi Mount
156” Pull
1 – 12”
4”
CAT II-III Q.H.
Clevis
Cat II (Offsets 15” Left/Right)
Round Pan
55 HP
30 HP
30 HP
120 HP
110 HP
2-3/8”
17,004 FPM
16,821 FPM
2-1/2”
Cat 4
80 HP
55 HP
55 HP
210 HP
205 HP
2-3/8”
16,063 FPM
16,167 FPM
3”
Cat 4
10 Ga.
10 Ga.
1/4” x 10”
Std.
Std.
Std.
2000 lbs.
2420 lbs.
2260 lbs.
10 Ga.
10 Ga.
1/4” x 10”
Std.
Std.
Std.
2586 lbs.
3210 lbs.
2820 lbs.
Extra Equipment
Optional Equipment
• Spring Shock Absorber (Pull or Semi-Mount)
• Check Chain (Lift or Semi-Mount)
• Auxiliary Wheel Spindle Kit (Pull)
•
•
•
•
•
•
Front and Rear Single or Double Chain Guards
540 or 1000 RPM
Constant Velocity or Non-Constant Velocity Driveline (Pull)
Ratchet Lift Screw or Hydraulic Cylinder (Pull or Semi-Mount)
Lift-Type, Pull-Type, or Semi-Mount Hydraulic Offset Hitch
Laminated Tire, Used Foam-Filled Airplane Tire and Wheel, Used Airplane Tire and Wheel or 15” Wheel (Pull-Type)
MODELS
©2007 Alamo Group Inc.
0207-OSP
Lift-type units are perfect for working in tight spots where the
maneuverability of a mounted cutter is required. (unit shown
with optional equipment)
The Turbo 96 and 120 are also available as a semi-mount
hydraulic offset unit to allow mowing of hard to reach areas
such as under trees. (unit shown with optional equipment)
Servis and Rhino are registered trademarks of Alamo Group Inc.
TURBO 96
•
TURBO 120
TURBO SERIES
Unit shown with optional equipment
The super-duty Rhino® Turbo 96 and Turbo 120 are 8ʼ and 10ʼ rotary cutters designed for use in demanding agricultural, commercial and
industrial mowing applications. They set the standard for premium design and performance in multi-spindle rotary cutters. Features include
the patented Turbo Dome™ double deck where both deck sheets cover the entire mainframe. The top sheet is domed for easier clean off
and minimal material build up. The lower deck sheet protects the upper sheet from being damaged. The Turbo Series also raises the bar
in power transmission. Both units feature high horsepower rated gearboxes and the highest maximum cutting capacity ratings in their
respective size classes. Other quality features include fast blade tip speeds for a clean cut, cross-braced pan blade carriers for greater
durability, and greaseable pivot bushings on the pull-type and semi-mount model axles for longer wear. Front and rear guarding, plus
shielded drivelines and gearboxes are standard for greater safety.
Designed for a wide range
of mowing applications
1020 South Sangamon Ave,
Gibson City, IL 60936
TEL 877.408.3297
FAX 877.408.3298
www.servis-rhino.com
•
•
•
•
•
•
•
Farms
Ranches
Commercial lots
Industrial sites
Groves or Orchards
Wildlife management areas
©2007 Alamo Group Inc.
Proven features and specifications
• Turbo Dome™ double deck that is domed for
easy clean off and minimal material build up.
• High horsepower rated gearboxes
• Highest maximum cutting capacity ratings in
their respective size classes
• Smooth, obstruction free underside of the deck
for efficient material flow through the cutting
chamber
• Deep decks to handle larger volumes of material
more easily
• Cross-braced pan blade carriers for greater
durability
RHINO TURBO SERIES ROTARY CUTTERS … 20 REASONS
WHY THEY ARE THE PREMIUM 8’ AND 10’ ROTARY CUTTERS
ON THE MARKET!
®
15. Reinforced Round
Pan Blade Carriers
14. Double
Deck Design
17. Heavy-Duty
Top Side Drivelines
19. Pedestal Mount
Carrier Bearing
18. Shielded Drivelines
and Gearboxes
20. Category 4 Driveline
13. Transport
Latch
1.
2.
3
4
5.
6.
7
8.
1. Hitch Options
12. Greaseable
Pivot Bushings
9
10
16.Large Heavy-Duty
Gearboxes
11.
12.
13
2. Maximum Cut
Capacity
14
15.
16.
17.
11. Auxiliary Wheel
Spindle Kit
18
9. Spring Shock
Absorber
(Optional
Equipment)
19.
20
3. Replaceable
Skid Shoes
10. Five Bolt
Wheel Hubs
4. Fast Blade
Tip Speeds
5. Side Skirts
8. Tire Options
7. Optional
Chain Guards
6. Turbo
Dome™ Deck
Turbo 120 pull-type shown with optional equipment
Your choice of hitch options-lift, pull, or semimount hyd. offset.
Highest maximum cut capacity ratings in their
size classes.
Replaceable skid shoes help save you time
and money.
Fast blade tip speeds for a clean cut.
Side skirts are 1/4” thick steel and 10” tall for
longer life and easier cutting of high volume
material.
Turbo Dome™ Deck design slopes front to rear
and side to side for easier clean off and minimal
material build up.
Front and rear single or double chain guards
are optional, deflectors are standard.
Tire options for the pull–type unit include
laminated, used foam-filled airplane tire, used
airplane tire or 15” wheel.
An optional spring shock absorber is
available to reduce shock loads to the deck (pulltype or semi-mount).
Five-bolt wheel hubs (pull-type) are standard
for greater load carrying capacity than cutters
with four-bolt wheel hubs.
Auxiliary wheel spindle kit (pull-type) is
available for applications requiring additional
tires and wheels.
Greaseable pivot bushings (pull and semimount axle) for longer life of the unit is standard.
A transport latch is standard (pull or semimount with hydraulic cylinder) to help safely
transport the unit.
Double deck design for great strength and help
maintaining a “new” look.
Reinforced round pan blade carriers for added
strength and support.
Large, heavy-duty gearboxes are among the
highest rated in their respective size classes.
Heavy-duty top side drivelines for improved
performance.
Shielded drivelines and gearboxes for greater
safety.
Pedestal mount carrier bearing design delivers
long lasting performance (pull-type).
Category 4 driveline is standard to deliver the
power to the cutter.
ROTARY CUTTERS
ROTARY CUTTERS
TURBO SERIES
Cutting Width
Transport Width
Overall Width
Overall Length
Cutting Height
Blade Overlap
Hitch: Lift
Pull
Semi Mount(Hyd. Offset)
Blade Carriers (Cross-Braced)
Tractor HP Required (Min.):
Lift (with adequate front weight)
Pull
Semi-Mount
Gearbox Rating: Center
Outboard
Output Shaft Diameter (Outboard)
Blade Tip Speed: 540 RPM
1000 RPM
Cutting Capacity (Max. Diameter)
Driveline Size
Deck Thickness (Turbo Dome™)
Upper Sheet
Lower Sheet
Side Skirts
Replaceable Skid Shoes
Safety Deflectors
Transport Latch: Pull or Semi-Mount
Weight (Approx.) Lift
Pull
Semi-Mount
STANDARD EQUIPMENT AND
SPECIFICATIONS
TURBO 96
TURBO 120
97”
104”
104”
101” Lift, Semi Mount
136” Pull
1-1/2” – 12”
4”
CAT II-III Q.H.
Clevis
Cat II (Offsets 11” Left/Right)
Round Pan
120”
127”
127”
117” Lift, Semi Mount
156” Pull
1 – 12”
4”
CAT II-III Q.H.
Clevis
Cat II (Offsets 15” Left/Right)
Round Pan
55 HP
30 HP
30 HP
120 HP
110 HP
2-3/8”
17,004 FPM
16,821 FPM
2-1/2”
Cat 4
80 HP
55 HP
55 HP
210 HP
205 HP
2-3/8”
16,063 FPM
16,167 FPM
3”
Cat 4
10 Ga.
10 Ga.
1/4” x 10”
Std.
Std.
Std.
2000 lbs.
2420 lbs.
2260 lbs.
10 Ga.
10 Ga.
1/4” x 10”
Std.
Std.
Std.
2586 lbs.
3210 lbs.
2820 lbs.
Extra Equipment
Optional Equipment
• Spring Shock Absorber (Pull or Semi-Mount)
• Check Chain (Lift or Semi-Mount)
• Auxiliary Wheel Spindle Kit (Pull)
•
•
•
•
•
•
Front and Rear Single or Double Chain Guards
540 or 1000 RPM
Constant Velocity or Non-Constant Velocity Driveline (Pull)
Ratchet Lift Screw or Hydraulic Cylinder (Pull or Semi-Mount)
Lift-Type, Pull-Type, or Semi-Mount Hydraulic Offset Hitch
Laminated Tire, Used Foam-Filled Airplane Tire and Wheel, Used Airplane Tire and Wheel or 15” Wheel (Pull-Type)
MODELS
©2007 Alamo Group Inc.
0207-OSP
Lift-type units are perfect for working in tight spots where the
maneuverability of a mounted cutter is required. (unit shown
with optional equipment)
The Turbo 96 and 120 are also available as a semi-mount
hydraulic offset unit to allow mowing of hard to reach areas
such as under trees. (unit shown with optional equipment)
Servis and Rhino are registered trademarks of Alamo Group Inc.
TURBO 96
•
TURBO 120
TURBO SERIES
Unit shown with optional equipment
The super-duty Rhino® Turbo 96 and Turbo 120 are 8ʼ and 10ʼ rotary cutters designed for use in demanding agricultural, commercial and
industrial mowing applications. They set the standard for premium design and performance in multi-spindle rotary cutters. Features include
the patented Turbo Dome™ double deck where both deck sheets cover the entire mainframe. The top sheet is domed for easier clean off
and minimal material build up. The lower deck sheet protects the upper sheet from being damaged. The Turbo Series also raises the bar
in power transmission. Both units feature high horsepower rated gearboxes and the highest maximum cutting capacity ratings in their
respective size classes. Other quality features include fast blade tip speeds for a clean cut, cross-braced pan blade carriers for greater
durability, and greaseable pivot bushings on the pull-type and semi-mount model axles for longer wear. Front and rear guarding, plus
shielded drivelines and gearboxes are standard for greater safety.
Designed for a wide range
of mowing applications
1020 South Sangamon Ave,
Gibson City, IL 60936
TEL 877.408.3297
FAX 877.408.3298
www.servis-rhino.com
•
•
•
•
•
•
•
Farms
Ranches
Commercial lots
Industrial sites
Groves or Orchards
Wildlife management areas
©2007 Alamo Group Inc.
Proven features and specifications
• Turbo Dome™ double deck that is domed for
easy clean off and minimal material build up.
• High horsepower rated gearboxes
• Highest maximum cutting capacity ratings in
their respective size classes
• Smooth, obstruction free underside of the deck
for efficient material flow through the cutting
chamber
• Deep decks to handle larger volumes of material
more easily
• Cross-braced pan blade carriers for greater
durability