Pataco CableAlarm

Pataco CableAlarm
SI8S CAB-AL AM-RF
SI8M CAB-AL AM-RF
EN
COMPONENT INSTRUCTION
4. Cable
8. Lock
1. Cable end
2. Slot
3. Button
9. Battery cover
screw
5. Battery Cover
6. Speaker
7. LED
MULTI ALARM TECHNOLOGY
Alarm 1 and 3:
Alarm 2:
Stolen merchandise with CableAlarm attached, will
trigger EAS alarm and set self alarm as well.
Anti tamper, the CableAlarm sets alarm if it is tampered or if the wire is cut. The armed CableAlarm
will alarm if the battery cover is removed.
ALARM
1
ALARM
ALARM
2
3
Pataco AG
Looäcker 1
CH-9247 Henau, Switzerland
www.pataco.com - [email protected]
Int. Freecall: +800 72 82 26 24
INSTRUCTION MANUAL
1
© Pataco AG 08/2012 release 1.1
Pataco CableAlarm
SI8S CAB-AL AM-RF
SI8M CAB-AL AM-RF
HOW TO ATTACH
HOW TO RELEASE
1
Attach cable trough any hole or sleeve.
1
Place the detacher onto the
knuckle.
2
Place the cable end into the
slot.
2
Press the button and it pops out.
3
Pull out the cable end and remove
the CableAlarm.
Short cable
3
Push the button. LED flashes once
and speaker beeps once. It is now
protected.
Long cable
Pataco AG
Looäcker 1
CH-9247 Henau, Switzerland
www.pataco.com - [email protected]
Int. Freecall: +800 72 82 26 24
INSTRUCTION MANUAL
2
Pataco CableAlarm
SI8S CAB-AL AM-RF
SI8M CAB-AL AM-RF
HOW TO CHANGE BATTERY
1
Use special screwdriver to take the
battery cover screw out.
2
Open battery cover in direction of
arrow.
3
Use special screwdriver to loosen
the battery, then take out the
battery.
4
Fit the new battery in correct
position and use battery cover to
press in.
5
Mount the battery cover.
6
Thighten the screws.
5
Mount the new cable and arrange
thin wire to avoid interference with
switch (black).
HOW TO CHANGE CABLE
1, 2 Please refer "HOW TO CHANGE BATTERY" step 1 and 2
3 Pull out the plug of socket.
4 Take out the cable.
6
Plug in the white plug.
Pataco AG
Looäcker 1
CH-9247 Henau, Switzerland
www.pataco.com - [email protected]
Int. Freecall: +800 72 82 26 24
7
Mount the battery cover and
thighten the screws.
INSTRUCTION MANUAL
3
© Pataco AG 01/2011 release 1.0
Pataco CableAlarm
SI8S CAB-AL AM-RF
SI8M CAB-AL AM-RF
HOW TO STOP THE ALARM
Place the detacher onto the knockle, push and release the
button. The alarm will stop immediately.
Press the button and
it pops out.
SPECIFICATION
Frequency: Dimension:
Color: Alarm decibel: Cable diamter: Cable length:
AM: 58KHz / RF: 8.2MHz
90 x 50 x 20 mm
black or customized
95dB
Ø 6 mm
130 mm, 170 mm,
1500 mm or customize
Lock: super or normal
Battery:CR2032
Usage environement
Temperature: 0 - 40°C (32 - 104F)
Humidity: 20% - 85%
NOTE
•
•
•
Working indicator:
1. While arming the CableAlarm, LED flashes and speakter beeps once.
2. No LED flash when CableAlarm is attached on merchandise.
3. When alarm is triggered, the speaker beeps continuously and LED flashes.
Low battery indicator:
While arming the CableAlarm, LED flashes 10 times whithout any beeps. Battery have to be replace.
Defective CableAlarms must be duly disposed of. The battery and the CableAlarms must to be disposed of separately
from each other and are not allowed to arrive into the domestic refuse.
Pataco AG
Looäcker 1
CH-9247 Henau, Switzerland
www.pataco.com - [email protected]
Int. Freecall: +800 72 82 26 24
INSTRUCTION MANUAL
4