O-Ring Design Guide - Hi

Transcription

O-Ring Design Guide
ISO
9001
REGISTERED QMS
ISD
www.hitechseals.com
Table of Contents
Hi-Tech Seals Inc. Compound Specifications
3
Machining Specifications
4
O-Ring Cross-Section
4
O-Ring Gland Types
4
ID Stretch/OD Interference
5
Reduction in Cross-Section
6
Compression
6
Gland Fill
7
Extrusion Gap
8
Groove Dimensions - ISO 3601
9
Groove Detail
11
Tolerances for Non-Standard O-Rings
12
Groove Dimensions - Din. 3771
13
O-Ring Sizing Charts
2
O-Ring Design Guide
16
Imperial O-Ring Sizes
16
Metric O-Ring Sizes
24
Common O-Ring Failures
42
Material Guides
46
Edmonton, AB (Head Office)
9211 - 41 Avenue NW
780.438.6055
www.hitechseals.com
Compound Specification Guide
O-Ring Design Guide
Compound
Elastomer Type
Durometer
Temperature Range
Service
A general service Nitrile compound for a wide range of applications including
petroleum based fluids. Nitrile compounds also have excellent resistance to
compression set, tear and abrasion resistance.
Generally used for higher pressures than the 70 durometer materials, while having
comparable media resistance.
N70
Nitrile
70 +/- 5
-40°C to 120°C
-40°F to 248°F
N90
Nitrile
90 +/- 5
-25°C to 120°C
-13°F to 248°F
LTN
Nitrile
70 +/- 5
-55°C to 120°C
-67°F to 248°F
HS7
Highly Saturated
Nitrile
70 +/- 5
-40°C to 150°C
-40°F to 302°F
HS8
Highly Saturated
Nitrile
80 +/- 5
-40°C to 150°C
-40°F to 302°F
A low temperature Nitrile compound for use in applications where sealability
at lower temperatures is important. Due to the lower acrylonitrile content, this
compound will show slightly less resistance to petroleum products.
This is a hydrogenated Nitrile compound which provides the material with
improved resistance to heat, ozone and aging. Similar applications to Nitrile but
with improved mechanical properties and media resistance. Excellent for many
oilfield and automotive applications. H2S resistance up to 10%.
Generally used for higher pressures than the 70 durometer materials while having
HS9
Highly Saturated
Nitrile
90 +/- 5
-40°C to 150°C
-40°F to 302°F
comparable media resistance. Improved ED resistance.
V75
Viton®
75 +/- 5
-25°C to 204°C
-13°F to 400°F
V90
Viton®
90 +/- 5
-25°C to 204°C
-13°F to 400°F
Genuine Viton® compounds have excellent resistance to ozone, weather, oxygen,
mineral oil, fuels, hydraulic fluids, aromatics, petroleum fluids, many organic
solvents and chemicals. Viton® is also used in high temperature applications.
Viton® Extreme™ TBR and ETP compounds are also available.
TBR- Totally Base Resistant compound that provides improved performance over
other TFE/Propylene polymers.
ETP- Provides the excellent thermal resistance of Viton® along with significantly
advanced chemical resistance.
Genuine Viton® is generally used for higher pressure than the 75 durometer
materials while having comparable media resistance.
LTV
Viton® GLT-S
75 +/- 5
-40°C to 204°C
-40°F to 400°F
Genuine Viton® GLT-S is used for lower temperature applications than the 75
durometer materials while having comparable media resistance.
PF7
Perfluoroelastomer
75 +/- 5
-15°C to 300°C
5°F to 572°F
Perfluroelastomer materials combine the best heat and chemical resistance
performance compared to other elastomer materials.
PF9
Perfluoroelastomer
90 +/- 5
-4°C to 230°C
25°F to 466°F
Tetrafluoroethylene-Propylene materials exhibit exceptional thermal and chemical
resistance including hot water, steam, acids, alkaline solutions, ammonia, amines,
brake fluids, petroleum fluids and sour gas. Low temperature may restrict sealing
abilities.
Neoprene is a general purpose material for refrigerants, ozone and weather.
A80
Aflas™
80 +/- 5
0°C to 230°C
32°F to 446°F
NEO
Neoprene
70 +/- 5
-45°C to 135°C
-49°F to 275°F
E70
Ethylene- Propylene
70 +/- 5
-54°C to 150°C
-65°F to 302°F
Ethylene-Propylene materials exhibit excellent resistance to water, steam, brake
fluids and ozone.
E80
Ethylene- Propylene
80 +/- 5
-54°C to 150°C
-65°F to 302°F
Generally used for higher pressures than 70 durometer EPDM compounds while
having comparable media resistance.
S70
Silicone
70 +/- 5
-55°C to 230°C
-67°F to 446°F
Silicone compounds offer the widest elastomer temperature range but typically
can not be used in dynamic applications or petroleum based fluids.
FS7
Fluorosilicone
70 +/- 5
-55°C to 200°C
-67°F to 392°F
Fluorosilicone for use in petroleum and synthetic oils, greases, amines, aminetreated hydrocarbons and steam.
F.D.A., NSF and UL listed or approved materials available upon request. We also offer a complete range of coloured or internally lubed compounds as required. Some materials are available in durometers
that range from 40 to 95 shore A. Most compounds available in metric sizing. Hi-Tech Seals Inc. also offers a complete range of back-up rings, anti-extrusion devices as well as X-rings and square cut
rings. These products are available in a variety of sizes and materials, please contact your sales office for more information.
www.hitechseals.com
9211 - 41 Avenue NW
780.438.6055
3
O-Ring Design Guide
O-Ring Cross-Section
The I.D. and O.D. of an O-ring gland is primarily influenced by diameter of the mating surface of the rod or piston and bore.
Although the cross-section of the O-ring is seen as fairly arbitrary, there are some distinct advantages to either a larger or smaller
cross-section O-ring. Listed below are the advantages of small cross-sections and the advantages of large cross-sections:
Advantages of Smaller Cross-Section
•
•
•
•
•
Advantages of Larger Cross-Section
More compact
Lighter weight
Less expensive; especially for higher cost elastomers like
FKM or fluorosilicone
Less machining required for machined grooves since
grooves are smaller
More resistant to explosive decompression
•
•
•
•
Less prone to compression set
Less volume swell in liquid on a percentage basis
Allows for larger tolerance while still maintaining
acceptable compression squeeze and compression ratio
over full stack-up range
Less prone to leakage due to contamination; dirt, lint,
scratches, etc.
O-Ring Gland Types
O-rings are primarily used to prevent the loss of a fluid or gas. However, O-rings can be used as dust seals, drive belts or on
rotating shafts. Most O-ring seals can be classified into one of the three arrangements shown below.
Piston Configuration
4
Rod Configuration
Face Type Configuration
9211 - 41 Avenue NW
780.438.6055
www.hitechseals.com
O-Ring Design Guide
Piston
O-Ring
O.D.
I.D.
Rod
C/S
Gland Ø
Gland Ø
I.D. Stretch/O.D. Interference
For hydraulic and pneumatic piston sealing applications
The O-ring inside diameter (I.D.) should be stretched between 2% and 5% for dynamic applications and 2% and 8% for static
applications. For O-rings with an inside diameter smaller than 20 mm, this is not always possible which can result in a wider
range of stretch. To minimize this range and the maximum stretch, it is necessary to minimize the tolerance of the piston gland
diameter, and have a less stringent requirement for the minimum O-ring stretch. In dynamic applications, it is important to keep
the maximum stretch to 5% or less to avoid detrimental effects on sealing performance.
For hydraulic and pneumatic rod sealing applications
The O-ring's outside diameter (O.D.) should be at least equal to or larger than the rod gland diameter to give interference on the
O-ring's outside diameter (O.D.). The O-ring's outside diameter (O.D.) should not exceed 3% of the rod gland diameter for O-rings
with an inside diameter (I.D.) greater than 250 mm, or 5% for O-rings with an inside diameter (I.D.) smaller than 250 mm. For
O-rings with an inside diameter (I.D.) smaller than 20 mm, this is not always possible due to tolerance issues, which can result in a
greater O-ring outside diameter (O.D.) interference.
www.hitechseals.com
9211 - 41 Avenue NW
780.438.6055
5
O-Ring Design Guide
Reduction in Cross-Section
If the I.D. of the O-ring is stretched, the cross-section of the O-ring will decrease. The following table gives the O-ring crosssections that result from various percentages of I.D. stretch.
Original O-Ring C/S
Reduced O-Ring C/S at % ID Stretch (Inch/mm)
O-Ring
Series
Inch
mm
1%
2%
3%
4%
5%
000
0.070
1.78
0.069/1.76
0.069/1.74
0.068/1.73
0.068/1.71
0.068/1.69
100
0.103
2.62
0.102/2.59
0.101/2.57
0.100/2.54
0.100/2.52
0.100/2.49
200
0.139
3.53
0.138/3.49
0.137/3.46
0.136/3.42
0.135/3.39
0.134/3.35
300
0.210
5.33
0.208/5.28
0.206/5.22
0.205/5.17
0.204/5.12
0.203/5.06
400
0.275
6.99
0.272/6.92
0.270/6.85
0.268/6.78
0.267/6.71
0.266/6.64
Compression
The difference between the original O-ring cross-section and the final O-ring cross-section once installed is known as the
compression squeeze.
Compression Squeeze
C/S
Compression Squeeze = C/S - D
D
This can usually be expressed as a percentage:
O-ring C/S Squeeze (%) = Compression Squeeze x 100
C/S
For recommended O-ring C/S squeeze (%) values please refer to page 9-10.
6
9211 - 41 Avenue NW
780.438.6055
www.hitechseals.com
O-Ring Design Guide
Gland Fill
The gland fill is the percentage of the gland that is occupied by the O-ring. It is calculated by dividing the cross-sectional area
(CSA) of the O-ring by the cross-sectional area of the gland.
Area of a circle = πr2 and r = d , where d = diameter (C/S)
2
( )
Therefore, O-ring CSA = π C/S 2
2
w
Gland CSA = D x w*
Gland Fill (%) = O-ring CSA
Gland CSA
D
w- groove width, D- groove depth
x 100
* Effect of gland angle and extrusion gap not
addressed.
It is important to consider the groove fill or occupancy of the installed O-ring to avoid detrimental effects on radial sealing
performance. Groove fill of the installed O-ring should not be more than 85 % to allow for possible O-ring thermal expansion,
volume swell due to fluid exposure and effects of tolerances.
Volume change is the increase or decrease of the volume of an elastomer after it has been in contact with a fluid, measured in
percent (%). For static O-ring applications volume swell up to 30 % can usually be tolerated. For dynamic applications, 10 or 15
% swell is a reasonable maximum unless special provisions are made in the gland design itself. This is a general rule and there may
occasionally be exceptions.
It is also important to note there are significant differences in the coefficients of thermal expansion between the O-ring material and
the groove materials. Elastomers can have coefficients of thermal expansion 7 to 20 times higher than that of metal, such as steel.
www.hitechseals.com
9211 - 41 Avenue NW
780.438.6055
7
O-Ring Design Guide
Extrusion Gap
Extrusion is a concern for radial seals where there is gap between the piston and the bore for a piston type seal or between the rod
and the bore for a rod type seal. It is not typically a concern for face type seals where the metal parts to be sealed are in contact
line-to-line. The issue is that at higher pressures and especially for softer O-ring elastomers, the O-ring can be forced by the pressure
into the small gap between the piston (or rod) and the bore. Unless the bore and the piston (or rod) are ensured to remain
concentric by the hardware, we have to assume that entire possible gap can shift to one side (see diagram below).
Piston Type Seal
Radial Extrusion Gap = Bore Ø- Piston Ø
2
Rod Type seal
Radial Extrusion Gap = Bore Ø- Rod Ø
2
A
A
B
High
Pressure
Extrusion
Gap
Extrusion
Radial Gap (A)
Diametrical Gap (B)
Maximum Possible Extrusion Gap
Limits for Extrusion
Reduce the clearance shown by 60% when
using silicone or fluoro-silicone elastomers.
Fluid Pressure (Bar)
690.0
552.0
414.0
LIMITS FOR EXTRUSION
10000
8000
6000
276.0
4000
207.0
3000
138.0
2000
EXTRUSION
69.0
55.2
1000
800
41.4
27.6
600
NO
EXTRUSION
400
20.7
300
13.8
200
6.9
mm 0
In. 0
.3
.5
.8
.010
.020
.030
DUROMETER
(HARDNESS SHORE A)
–70
–80
Fluid Pressure (psi)
There are different methods to counter O-ring extrusion. One
of these methods is to simply increase the durometer rating of
the O-ring. However, as you increase the durometer, the O-ring
can become less malleable. Another option would be the use of
anti-extrusion devices. These are thin rings made of hard plastic
materials such as PTFE, Nylon, and PEEK or a harder durometer
rubber such as Nitrile or Polyurethane. Once in place these rings
will provide essentially zero clearance.
100
1.0
.040
–90
Total Diametrical Clearance
8
9211 - 41 Avenue NW
780.438.6055
www.hitechseals.com
O-Ring Design Guide
Static Radial Applications
R
W
E/2
D
W*
Squeeze
D
E
R
Groove Width +0.010/-0.000
%
Diametrical
Clearance Max.
No
Back- Up Ring
One
Back- Up Ring
Two
Back- Up Rings
Groove
Radius
0.010 - 0.025
14 - 35
0.004
0.110
0.165
0.220
0.008 - 0.016
0.075 - 0.087
0.013 - 0.031
13 - 30
0.005
0.150
0.205
0.260
0.008 - 0.016
0.101 - 0.117
0.018 - 0.042
13 - 30
0.006
0.197
0.252
0.307
0.016 - 0.031
0.210
0.156 - 0.180
0.025 - 0.059
12 - 28
0.006
0.283
0.354
0.429
0.016 - 0.031
0.275
0.212 - 0.242
0.028 - 0.069
10 - 25
0.007
0.374
0.484
0.594
0.031 - 0.047
O-Ring
C/S
Groove
Depth
Inches
0.070
0.049 - 0.057
0.103
0.139
* Pneumatic applications typically do not use a Back-up ring.
Static Axial (Face) Applications
W
D
R
W
Squeeze
C/S
D
Groove Depth +0.004/-0.000
%
Hydraulic
Pneumatic/Vacuum
R
Groove
Radius
0.070
0.051
21 - 36
0.126
0.114
0.008 - 0.016
0.103
0.079
19 - 30
0.157
0.142
0.008 - 0.016
0.139
0.106
17 - 26
0.209
0.189
0.016 - 0.031
0.210
0.165
15 - 23
0.299
0.276
0.016 - 0.031
0.275
0.224
13 - 20
0.354
0.335
0.031 - 0.047
O-Ring
www.hitechseals.com
9211 - 41 Avenue NW
780.438.6055
9
O-Ring Design Guide
Reciprocating Applications
w
E/2
D
R
D
O-Ring
C/S
Groove Depth
Hydraulic
w*
E
Squeeze
R
Pneumatic
Diametrical
No
One
Two
Clearance
Back- Up
Back- Up
Back- Up
Max.
Ring
Ring
Rings
Hydraulic
Pneumatic
Inches
%
Inches
%
0.070
0.054 - 0.058
0.056 - 0.060
0.009 - 0.019
13 - 27
0.007 - 0.017
10 - 24
0.004
0.110
0.165
0.220
0.008 - 0.016
0.103
0.081 - 0.088
0.083 - 0.092
0.012 - 0.025
12 - 24
0.008 - 0.023
8 - 22
0.005
0.150
0.205
0.260
0.008 - 0.016
0.139
0.112 - 0.120
0.115 - 0.125
0.015 - 0.031
11 - 22
0.010 - 0.028
7 - 20
0.006
0.197
0.252
0.307
0.016 - 0.031
0.210
0.173 - 0.182
0.177 - 0.190
0.023 - 0.042
11 - 20
0.015 - 0.038
7 - 18
0.006
0.283
0.354
0.429
0.016 - 0.031
0.275
0.229 - 0.244
0.234 - 0.253
0.025 - 0.052
9 - 19
0.017 - 0.047
6 - 17
0.007
0.374
0.484
0.594
0.031 - 0.047
Groove Radius
* Pneumatic applications typically do not use a Back-up ring.
Note: For piston applications groove width (w) values do not apply for 001-003 and 400-424 series O-rings. For rod applications groove width
(w)values do not apply for 001-003, 028-050, 135-178, 232-284, 350-395, 400-424 and 430-475.
10
9211 - 41 Avenue NW
780.438.6055
www.hitechseals.com
O-Ring Design Guide
Groove Details
Piston & Rod Applications
a
e
b
d
c
c
e
b
d
a
Piston Application
O-Ring
Series
O-Ring C/S
Inch
mm
0
0.070
1.78
100
0.103
2.62
200
0.139
3.53
300
0.210
5.33
400
0.275
6.99
Wall
Angle
Break Edge
a
b
0-5°
Rod Application
Radius
Chamfer Length (e)
c
d at 15°
d at 20°
Inch
mm
Inch
mm
Inch
mm
0.008 - 0.016
0.20 - 0.40
0.043
1.10
0.035
0.90
0.004 - 0.012
Inch
0.008 - 0.016
0.20 - 0.40
0.059
1.50
0.043
1.10
0.10 - 0.30
mm
0.016 - 0.031
0.40 - 0.80
0.071
1.80
0.055
1.40
0.016 - 0.031
0.40 - 0.80
0.106
2.70
0.083
2.10
0.031 - 0.047
0.80 - 1.20
0.142
3.60
0.110
2.80
Surface Finish
The surface roughness of the O-ring gland and any mating part has a significant impact on the life and sealing performance of
the O-ring. The following are general fluid sealing surface roughness values in microinches (µinch):
For a static mating surface: Ra 16-32 µinch
For a dynamic mating surface: Ra 8-16 µinch
www.hitechseals.com
9211 - 41 Avenue NW
780.438.6055
11
Tolerances for Non-Standard O-Rings
I.D.
C/S
Machining information and tolerances for various standards are
available through Hi-Tech Seals.
12
O-Ring Design Guide
Cross Section
mm
Tolerance
mm
0.80 < C/S ≤ 3.15
± 0.08
3.15 < C/S ≤ 4.50
± 0.10
4.50 < C/S ≤ 6.30
± 0.13
6.30 < C/S ≤ 8.40
± 0.15
Inside Diameter
mm
Tolerance
mm
0.68 to 1.53
± 0.10
1.54 to 11.69
± 0.13
11.70 to 13.46
± 0.15
13.47 to 17.53
± 0.18
17.54 to 20.57
± 0.20
20.58 to 23.88
± 0.23
23.89 to 28.70
± 0.25
28.71 to 35.56
± 0.30
35.57 to 43.18
± 0.36
43.19 to 50.80
± 0.41
50.81 to 58.42
± 0.46
58.43 to 66.55
± 0.51
66.56 to 74.93
± 0.56
74.94 to 83.57
± 0.61
83.58 to 92.20
± 0.66
92.21 to 101.60
± 0.71
101.61 to 117.35
± 0.76
117.36 to 141.22
± 0.89
141.23 to 166.37
± 1.02
166.38 to 192.02
± 1.14
192.03 to 218.69
± 1.27
218.70 to 253.37
± 1.40
253.38 to 289.56
± 1.52
289.57 to 347.98
± 1.78
347.99 to 408.94
± 2.03
408.95 to 472.44
± 2.29
472.45 to 571.50
± 2.54
571.51 to 711.20
± 3.05
711.21 to 855.98
± 3.56
855.99 to 1005.84
± 4.06
1005.85 to 1163.32
± 4.57
1163.33 to 1320.80
± 5.08
9211 - 41 Avenue NW
780.438.6055
www.hitechseals.com
O-Ring Design Guide
Static Radial Applications
W
E/2
D
D
E
W
Max. Eccentricity
±
Gland Depth
±
Diametrical Clearance
Groove Width
(+0.13/-0.00)
1.00
0.08
0.72
0.02
0.10
1.35
0.05
1.20
0.08
0.87
0.02
0.10
1.60
0.05
1.50
0.08
1.09
0.02
0.10
2.00
0.05
1.60
0.08
1.16
0.03
0.10
2.10
0.05
1.78 - 1.80
0.08
1.29
0.03
0.10
2.35
0.05
1.90
0.08
1.38
0.03
0.10
2.50
0.05
2.00
0.08
1.45
0.04
0.10
2.65
0.05
2.40
0.08
1.90
0.04
0.10
3.25
0.05
2.50
0.08
1.98
0.04
0.10
3.40
0.05
2.62
0.08
2.07
0.04
0.10
3.55
0.05
3.00
0.08
2.40
0.04
0.15
4.05
0.07
3.50 - 3.53
0.10
2.82
0.05
0.15
4.75
0.07
3.60
0.10
2.88
0.05
0.15
4.85
0.07
4.00
0.10
3.20
0.06
0.15
5.40
0.07
4.50
0.10
3.64
0.06
0.15
6.00
0.07
5.00
0.13
4.04
0.06
0.15
6.70
0.10
5.33- 5.34
0.13
4.31
0.08
0.15
7.15
0.10
5.50
0.13
4.45
0.08
0.15
7.35
0.10
5.70
0.13
4.61
0.08
0.15
7.65
0.10
6.00
0.13
4.91
0.08
0.18
8.15
0.13
6.99
0.15
5.72
0.10
0.18
9.50
0.13
7.00
0.15
5.73
0.10
0.18
9.55
0.13
7.50
0.15
6.14
0.10
0.18
10.20
0.13
8.00
0.15
6.55
0.10
0.18
10.90
0.13
8.40
0.15
6.87
0.15
0.18
11.45
0.13
C/S
www.hitechseals.com
9211 - 41 Avenue NW
780.438.6055
13
O-Ring Design Guide
Static Axial (Face) Applications
W
D
W
Groove Width
D
14
Hydraulic
Pneumatic
(+0.13/-0.00)
(± 0.13)
0.02
1.45
1.20
0.90
0.02
1.75
1.45
0.08
1.13
0.02
2.20
1.80
0.08
1.20
0.03
2.35
1.90
1.78 - 1.80
0.08
1.34
0.03
2.60
2.15
1.90
0.08
1.43
0.03
2.75
2.30
2.00
0.08
1.51
0.04
2.90
2.40
2.40
0.08
1.82
0.04
3.20
2.80
2.50
0.08
1.90
0.04
3.30
2.90
2.62
0.08
1.99
0.04
3.50
3.05
3.00
0.08
2.27
0.04
3.90
3.45
3.50 - 3.53
0.10
2.67
0.05
4.60
4.05
3.60
0.10
2.72
0.05
4.70
4.10
4.00
0.10
3.03
0.06
5.25
4.60
4.50
0.10
3.60
0.06
6.10
5.10
5.00
0.13
4.00
0.06
6.80
5.70
5.33
0.13
4.26
0.08
7.25
6.05
5.50
0.13
4.40
0.08
7.45
6.25
5.70
0.13
4.56
0.08
7.75
6.50
6.00
0.13
4.98
0.08
8.00
6.75
6.99
0.15
5.80
0.10
9.05
7.85
7.00
0.15
5.81
0.10
9.05
7.90
7.50
0.15
6.23
0.10
9.70
8.40
8.00
0.15
6.64
0.10
10.35
9.00
8.40
0.15
6.97
0.15
10.90
9.45
C/S
±
Gland Depth
1.00
0.08
0.75
1.20
0.08
1.50
1.60
±
9211 - 41 Avenue NW
780.438.6055
www.hitechseals.com
O-Ring Design Guide
Reciprocating Applications
E/2
W
D
D
C/S
±
Gland Depth
±
E
W
Diametral
Groove Width
Max.
Clearance
(+0.13/-0.00)
Eccentricity
1.00
0.08
0.80
0.02
0.10
1.35
0.05
1.20
0.08
0.96
0.02
0.10
1.60
0.05
1.50
0.08
1.20
0.02
0.10
2.00
0.05
1.60
0.08
1.28
0.03
0.10
2.10
0.05
1.78 - 1.80
0.08
1.42
0.03
0.10
2.40
0.05
1.90
0.08
1.52
0.03
0.10
2.50
0.05
2.00
0.08
1.60
0.04
0.10
2.65
0.05
2.40
0.08
2.06
0.04
0.10
3.25
0.05
2.50
0.08
2.15
0.04
0.10
3.40
0.05
2.62
0.08
2.25
0.04
0.10
3.55
0.05
3.00
0.08
2.61
0.04
0.15
4.05
0.07
3.50 - 3.53
0.10
3.07
0.05
0.15
4.75
0.07
3.60
0.10
3.13
0.05
0.15
4.85
0.07
4.00
0.10
3.48
0.05
0.15
5.40
0.07
4.50
0.10
3.99
0.05
0.15
6.00
0.07
5.00
0.13
4.44
0.05
0.15
6.70
0.10
5.33- 5.34
0.13
4.73
0.05
0.15
7.15
0.10
5.50
0.13
4.88
0.05
0.15
7.40
0.10
5.70
0.13
5.06
0.05
0.15
7.60
0.10
6.00
0.13
5.19
0.05
0.18
8.15
0.13
6.99
0.15
6.05
0.05
0.18
9.50
0.13
7.00
0.15
6.06
0.05
0.18
9.55
0.13
7.50
0.15
6.49
0.05
0.18
10.20
0.13
8.00
0.15
6.92
0.05
0.18
10.90
0.13
8.40
0.15
7.27
0.05
0.18
11.45
0.13
www.hitechseals.com
9211 - 41 Avenue NW
780.438.6055
15
O-Ring Design Guide
I.D.
Dash
Number
001
002
003
004
005
006
007
008
009
010
011
012
013
014
015
016
017
018
019
020
021
022
023
024
025
026
027
028
029
030
031
032
033
034
035
036
037
038
039
040
041
042
043
16
Nominal
I.D.
1/32
3/64
1/16
5/64
3/32
1/8
5/32
3/16
7/32
1/4
5/16
3/8
7/16
1/2
9/16
5/8
11/16
3/4
13/16
7/8
15/16
1
1 - 1/16
1 - 1/8
1 - 3/16
1 - 1/4
1 - 5/16
1 - 3/8
1 - 1/2
1 - 5/8
1 - 3/4
1 - 7/8
2
2 - 1/8
2 - 1/4
2 - 3/8
2 - 1/2
2 - 5/8
2 - 3/4
2 - 7/8
3
3 - 1/4
3 - 1/2
Imperial Actual
C/S
1/32
3/64
1/16
1/16
1/16
1/16
1/16
1/16
1/16
1/16
1/16
1/16
1/16
1/16
1/16
1/16
1/16
1/16
1/16
1/16
1/16
1/16
1/16
1/16
1/16
1/16
1/16
1/16
1/16
1/16
1/16
1/16
1/16
1/16
1/16
1/16
1/16
1/16
1/16
1/16
1/16
1/16
1/16
I.D.
0.029
0.042
0.056
0.070
0.101
0.114
0.145
0.176
0.208
0.239
0.301
0.364
0.426
0.489
0.551
0.614
0.676
0.739
0.801
0.864
0.926
0.989
1.051
1.114
1.176
1.239
1.301
1.364
1.481
1.614
1.739
1.864
1.989
2.114
2.239
2.364
2.489
2.614
2.739
2.864
2.989
3.239
3.489
Metric Actual
C/S
± 0.004
± 0.004
± 0.004
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.007
± 0.009
± 0.009
± 0.009
± 0.009
± 0.009
± 0.009
± 0.010
± 0.010
± 0.010
± 0.011
± 0.011
± 0.011
± 0.013
± 0.013
± 0.013
± 0.015
± 0.015
± 0.018
± 0.018
± 0.018
± 0.018
± 0.018
± 0.020
± 0.020
± 0.020
± 0.024
± 0.024
± 0.024
0.040
0.050
0.060
0.070
0.070
0.070
0.070
0.070
0.070
0.070
0.070
0.070
0.070
0.070
0.070
0.070
0.070
0.070
0.070
0.070
0.070
0.070
0.070
0.070
0.070
0.070
0.070
0.070
0.070
0.070
0.070
0.070
0.070
0.070
0.070
0.070
0.070
0.070
0.070
0.070
0.070
0.070
0.070
C/S
I.D.
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
0.74
1.07
1.42
1.78
2.57
2.90
3.68
4.47
5.28
6.07
7.65
9.25
10.82
12.42
14.00
15.60
17.17
18.77
20.35
21.95
23.52
25.12
26.70
28.30
29.87
31.47
33.05
34.65
37.62
41.00
44.17
47.35
50.52
53.70
56.87
60.05
63.22
66.40
69.57
72.75
75.92
82.27
88.62
C/S
± 0.10
± 0.10
± 0.10
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.18
± 0.23
± 0.23
± 0.23
± 0.23
± 0.23
± 0.23
± 0.25
± 0.25
± 0.25
± 0.28
± 0.28
± 0.28
± 0.33
± 0.33
± 0.33
± 0.38
± 0.38
± 0.46
± 0.46
± 0.46
± 0.46
± 0.46
± 0.51
± 0.51
± 0.51
± 0.61
± 0.61
± 0.61
1.02
1.27
1.52
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
9211 - 41 Avenue NW
780.438.6055
www.hitechseals.com
O-Ring Design Guide
Dash
Number
Imperial Actual
Nominal
I.D.
C/S
044
045
046
047
048
049
050
3 - 3/4
4
4 - 1/4
4 - 1/2
4 - 3/4
5
5 - 1/4
1/16
1/16
1/16
1/16
1/16
1/16
1/16
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
1/16
3/32
1/8
5/32
3/16
7/32
1/4
5/16
3/8
7/16
1/2
9/16
5/8
11/16
3/4
13/16
7/8
15/16
1
1 - 1/16
1 - 1/8
1 - 3/16
1 - 1/4
1 - 5/16
1 - 3/8
1 - 7/16
1 - 1/2
1 - 9/16
1 - 5/8
1 - 11/16
1 - 3/4
1 - 13/16
1 - 7/8
1 - 15/16
2
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
I.D.
Metric Actual
C/S
I.D.
C/S
3.739
3.989
4.239
4.489
4.739
4.989
5.239
± 0.027
± 0.027
± 0.030
± 0.030
± 0.030
± 0.037
± 0.037
0.070
0.070
0.070
0.070
0.070
0.070
0.070
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
94.97
101.32
107.67
114.02
120.37
126.72
133.07
± 0.69
± 0.69
± 0.76
± 0.76
± 0.76
± 0.94
± 0.94
1.78
1.78
1.78
1.78
1.78
1.78
1.78
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
0.049
0.081
0.112
0.143
0.174
0.206
0.237
0.299
0.362
0.424
0.487
0.549
0.612
0.674
0.737
0.799
0.862
0.924
0.987
1.049
1.112
1.174
1.237
1.299
1.362
1.424
1.487
1.549
1.612
1.674
1.737
1.799
1.862
1.925
1.987
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.007
± 0.009
± 0.009
± 0.009
± 0.010
± 0.010
± 0.010
± 0.010
± 0.010
± 0.010
± 0.012
± 0.012
± 0.012
± 0.012
± 0.012
± 0.012
± 0.015
± 0.015
± 0.015
± 0.015
± 0.015
± 0.015
± 0.017
± 0.017
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
1.24
2.06
2.84
3.63
4.42
5.23
6.02
7.59
9.19
10.77
12.37
13.94
15.54
17.12
18.72
20.29
21.89
23.47
25.07
26.64
28.24
29.82
31.42
32.99
34.59
36.17
37.77
39.34
40.94
42.52
44.12
45.69
47.29
48.90
50.47
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.18
± 0.23
± 0.23
± 0.23
± 0.25
± 0.25
± 0.25
± 0.25
± 0.25
± 0.25
± 0.30
± 0.30
± 0.30
± 0.30
± 0.30
± 0.30
± 0.38
± 0.38
± 0.38
± 0.38
± 0.38
± 0.38
± 0.43
± 0.43
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
www.hitechseals.com
9211 - 41 Avenue NW
780.438.6055
17
O-Ring Design Guide
Dash
Number
18
Nominal
I.D.
Metric Actual
Actual Sizing
C/S
I.D.
C/S
I.D.
C/S
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
2 - 1/16
2 - 1/8
2 - 3/16
2 - 1/4
2 - 5/16
2 - 3/8
2 - 7/16
2 - 1/2
2 - 9/16
2 - 5/8
2 - 11/16
2 - 3/4
2 - 13/16
2 - 7/8
3
3 - 1/4
3 - 1/2
3 - 3/4
4
4 - 1/4
4 - 1/2
4 - 3/4
5
5 - 1/4
5 - 1/2
5 - 3/4
6
6 - 1/4
6 - 1/2
6 - 3/4
7
7 - 1/4
7 - 1/2
7 - 3/4
8
8 - 1/4
8 - 1/2
8 - 3/4
9
9 - 1/4
9 - 1/2
9 - 3/4
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
2.050
2.112
2.175
2.237
2.300
2.362
2.425
2.487
2.550
2.612
2.675
2.737
2.800
2.862
2.987
3.237
3.487
3.737
3.987
4.237
4.487
4.737
4.987
5.237
5.487
5.737
5.987
6.237
6.487
6.737
6.987
7.237
7.487
7.737
7.987
8.237
8.487
8.737
8.987
9.237
9.487
9.737
± 0.017
± 0.017
± 0.017
± 0.017
± 0.020
± 0.020
± 0.020
± 0.020
± 0.020
± 0.020
± 0.022
± 0.022
± 0.022
± 0.022
± 0.024
± 0.024
± 0.024
± 0.028
± 0.028
± 0.030
± 0.030
± 0.030
± 0.035
± 0.035
± 0.035
± 0.035
± 0.035
± 0.040
± 0.040
± 0.040
± 0.040
± 0.045
± 0.045
± 0.045
± 0.045
± 0.050
± 0.050
± 0.050
± 0.050
± 0.055
± 0.055
± 0.055
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
0.103
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
52.07
53.64
55.25
56.82
58.42
59.99
61.60
63.17
64.77
66.34
67.95
69.52
71.12
72.69
75.87
82.22
88.57
94.92
101.27
107.62
113.97
120.32
126.67
133.02
139.37
145.72
152.07
158.42
164.77
171.12
177.47
183.82
190.17
196.52
202.87
209.22
215.57
221.92
228.27
234.62
240.97
247.32
± 0.43
± 0.43
± 0.43
± 0.43
± 0.51
± 0.51
± 0.51
± 0.51
± 0.51
± 0.51
± 0.56
± 0.56
± 0.56
± 0.56
± 0.61
± 0.61
± 0.61
± 0.71
± 0.71
± 0.76
± 0.76
± 0.76
± 0.89
± 0.89
± 0.89
± 0.89
± 0.89
± 1.02
± 1.02
± 1.02
± 1.02
± 1.14
± 1.14
± 1.14
± 1.14
± 1.27
± 1.27
± 1.27
± 1.27
± 1.40
± 1.40
± 1.40
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
201
202
203
204
205
206
207
3/16
1/4
5/16
3/8
7/16
1/2
9/16
1/8
1/8
1/8
1/8
1/8
1/8
1/8
0.171
0.234
0.296
0.359
0.421
0.484
0.546
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.007
0.139
0.139
0.139
0.139
0.139
0.139
0.139
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
4.34
5.94
7.52
9.12
10.69
12.29
13.87
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.18
3.53
3.53
3.53
3.53
3.53
3.53
3.53
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
9211 - 41 Avenue NW
780.438.6055
www.hitechseals.com
O-Ring Design Guide
Dash
Number
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
Nominal
I.D.
C/S
5/8
1/8
11/16
1/8
3/4
1/8
13/16
1/8
7/8
1/8
15/16
1/8
1
1/8
1 - 1/16
1/8
1 - 1/8
1/8
1 - 3/16
1/8
1 - 1/4
1/8
1 - 5/16
1/8
1 - 3/8
1/8
1 - 7/16
1/8
1 - 1/2
1/8
1 - 5/8
1/8
1 - 3/4
1/8
1 - 7/8
1/8
2
1/8
2 - 1/8
1/8
2 - 1/4
1/8
2 - 3/8
1/8
2 - 1/2
1/8
2 - 5/8
1/8
2 - 3/4
1/8
2 - 7/8
1/8
3
1/8
3 - 1/8
1/8
3 - 1/4
1/8
3 - 3/8
1/8
3 - 1/2
1/8
3 - 5/8
1/8
3 - 3/4
1/8
3 - 7/8
1/8
4
1/8
4 - 1/8
1/8
4 - 1/4
1/8
4 - 3/8
1/8
4 - 1/2
1/8
4 - 5/8
1/8
4 - 3/4
1/8
4 - 7/8
1/8
5
1/8
5 - 1/8
1/8
5 - 1/4
1/8
5 - 3/8
1/8
5 - 1/2
1/8
5 - 5/8
1/8
5 - 3/4
1/8
5 - 7/8
1/8
Actual Sizing
I.D.
0.609
0.671
0.734
0.796
0.859
0.921
0.984
1.046
1.109
1.171
1.234
1.296
1.359
1.421
1.484
1.609
1.734
1.859
1.984
2.109
2.234
2.359
2.484
2.609
2.734
2.859
2.984
3.109
3.234
3.359
3.484
3.609
3.734
3.859
3.984
4.109
4.234
4.359
4.484
4.609
4.734
4.859
4.984
5.109
5.234
5.359
5.484
5.609
5.734
5.859
Metric Actual
I.D.
C/S
± 0.009
± 0.009
± 0.010
± 0.010
± 0.010
± 0.010
± 0.010
± 0.010
± 0.012
± 0.012
± 0.012
± 0.012
± 0.012
± 0.012
± 0.015
± 0.015
± 0.015
± 0.018
± 0.018
± 0.018
± 0.020
± 0.020
± 0.020
± 0.020
± 0.024
± 0.024
± 0.024
± 0.024
± 0.024
± 0.024
± 0.024
± 0.028
± 0.028
± 0.028
± 0.028
± 0.028
± 0.030
± 0.030
± 0.030
± 0.030
± 0.030
± 0.035
± 0.035
± 0.035
± 0.035
± 0.035
± 0.035
± 0.035
± 0.035
± 0.035
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
15.47
17.04
18.64
20.22
21.82
23.39
24.99
26.57
28.17
29.74
31.34
32.92
34.52
36.09
37.69
40.87
44.04
47.22
50.39
53.57
56.74
59.92
63.09
66.27
69.44
72.62
75.79
78.97
82.14
85.32
88.49
91.67
94.84
98.02
101.19
104.37
107.54
110.72
113.89
117.07
120.24
123.42
126.59
129.77
132.94
136.12
139.29
142.47
145.64
148.82
C/S
± 0.23
± 0.23
± 0.25
± 0.25
± 0.25
± 0.25
± 0.25
± 0.25
± 0.30
± 0.30
± 0.30
± 0.30
± 0.30
± 0.30
± 0.38
± 0.38
± 0.38
± 0.46
± 0.46
± 0.46
± 0.51
± 0.51
± 0.51
± 0.51
± 0.61
± 0.61
± 0.61
± 0.61
± 0.61
± 0.61
± 0.61
± 0.71
± 0.71
± 0.71
± 0.71
± 0.71
± 0.76
± 0.76
± 0.76
± 0.76
± 0.76
± 0.89
± 0.89
± 0.89
± 0.89
± 0.89
± 0.89
± 0.89
± 0.89
± 0.89
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
www.hitechseals.com
9211 - 41 Avenue NW
780.438.6055
19
O-Ring Design Guide
Dash
Number
20
Nominal
Metric Actual
Actual Sizing
I.D.
C/S
I.D.
C/S
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
6
6 - 1/4
6 - 1/2
6 - 3/4
7
7 - 1/4
7 - 1/2
7 - 3/4
8
8 - 1/4
8 - 1/2
8 - 3/4
9
9 - 1/4
9 - 1/2
9 - 3/4
10
10 - 1/2
11
11 - 1/2
12
13
14
15
16
17
18
1/8
1/8
1/8
1/8
1/8
1/8
1/8
1/8
1/8
1/8
1/8
1/8
1/8
1/8
1/8
1/8
1/8
1/8
1/8
1/8
1/8
1/8
1/8
1/8
1/8
1/8
1/8
5.984
6.234
6.484
6.734
6.984
7.234
7.484
7.734
7.984
8.234
8.484
8.734
8.984
9.234
9.484
9.734
9.984
10.484
10.984
11.484
11.984
12.984
13.984
14.984
15.955
16.956
17.955
± 0.035
± 0.040
± 0.040
± 0.040
± 0.040
± 0.045
± 0.045
± 0.045
± 0.045
± 0.050
± 0.050
± 0.050
± 0.050
± 0.055
± 0.055
± 0.055
± 0.055
± 0.055
± 0.065
± 0.065
± 0.065
± 0.065
± 0.065
± 0.065
± 0.075
± 0.080
± 0.085
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
0.139
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
151.99
158.34
164.69
171.04
177.39
183.74
190.09
196.44
202.79
209.14
215.49
221.84
228.19
234.54
240.89
247.24
253.59
266.29
278.99
291.69
304.39
329.79
355.19
380.59
405.26
430.68
456.06
± 0.89
± 1.02
± 1.02
± 1.02
± 1.02
± 1.14
± 1.14
± 1.14
± 1.14
± 1.27
± 1.27
± 1.27
± 1.27
± 1.40
± 1.40
± 1.40
± 1.40
± 1.40
± 1.65
± 1.65
± 1.65
± 1.65
± 1.65
± 1.65
± 1.91
± 2.03
± 2.16
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
7/16
1/2
9/16
5/8
11/16
3/4
13/16
7/8
15/16
1
1 - 1/16
1 - 1/8
1 - 3/16
1 - 1/4
1 - 5/16
1 - 3/8
1 - 1/2
1 - 5/8
1 - 3/4
1 - 7/8
2
2 - 1/8
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
0.412
0.475
0.537
0.600
0.662
0.725
0.787
0.850
0.912
0.975
1.037
1.100
1.162
1.225
1.287
1.350
1.475
1.600
1.725
1.850
1.975
2.100
± 0.005
± 0.005
± 0.007
± 0.009
± 0.009
± 0.010
± 0.010
± 0.010
± 0.010
± 0.010
± 0.010
± 0.012
± 0.012
± 0.012
± 0.012
± 0.012
± 0.015
± 0.015
± 0.015
± 0.015
± 0.018
± 0.018
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
10.46
12.07
13.64
15.24
16.81
18.42
19.99
21.59
23.16
24.77
26.34
27.94
29.51
31.12
32.69
34.29
37.47
40.64
43.82
46.99
50.17
53.34
± 0.13
± 0.13
± 0.18
± 0.23
± 0.23
± 0.25
± 0.25
± 0.25
± 0.25
± 0.25
± 0.25
± 0.30
± 0.30
± 0.30
± 0.30
± 0.30
± 0.38
± 0.38
± 0.38
± 0.38
± 0.46
± 0.46
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
I.D.
C/S
9211 - 41 Avenue NW
780.438.6055
www.hitechseals.com
O-Ring Design Guide
Nominal
Dash
Number
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
Metric Actual
Actual Sizing
I.D.
C/S
2 - 1/4
2 - 3/8
2 - 1/2
2 - 5/8
2 - 3/4
2 - 7/8
3
3 - 1/8
3 - 1/4
3 - 3/8
3 - 1/2
3 - 5/8
3 - 3/4
3 - 7/8
4
4 - 1/8
4 - 1/4
4 - 3/8
4 - 1/2
4 - 5/8
4 - 3/4
4 - 7/8
5
5 - 1/8
5 - 1/4
5 - 3/8
5 - 1/2
5 - 5/8
5 - 3/4
5 - 7/8
6
6 - 1/4
6 - 1/2
6 - 3/4
7
7 - 1/4
7 - 1/2
7 - 3/4
8
8 - 1/4
8 - 1/2
8 - 3/4
9
9 - 1/4
9 - 1/2
9 - 3/4
10
10 - 1/2
11
11 - 1/2
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
I.D.
2.225
2.350
2.475
2.600
2.725
2.850
2.975
3.100
3.225
3.350
3.475
3.600
3.725
3.850
3.975
4.100
4.225
4.350
4.475
4.600
4.725
4.850
4.975
5.100
5.225
5.350
5.475
5.600
5.725
5.850
5.975
6.225
6.475
6.725
6.975
7.225
7.475
7.725
7.975
8.225
8.475
8.725
8.975
9.225
9.475
9.725
9.975
10.475
10.975
11.475
C/S
± 0.018
± 0.018
± 0.020
± 0.020
± 0.020
± 0.020
± 0.024
± 0.024
± 0.024
± 0.024
± 0.024
± 0.028
± 0.028
± 0.028
± 0.028
± 0.028
± 0.030
± 0.030
± 0.030
± 0.030
± 0.030
± 0.030
± 0.037
± 0.037
± 0.037
± 0.037
± 0.037
± 0.037
± 0.037
± 0.037
± 0.037
± 0.040
± 0.040
± 0.040
± 0.040
± 0.045
± 0.045
± 0.045
± 0.045
± 0.050
± 0.050
± 0.050
± 0.050
± 0.055
± 0.055
± 0.055
± 0.055
± 0.060
± 0.060
± 0.065
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
I.D.
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
56.52
59.69
62.87
66.04
69.22
72.39
75.57
78.74
81.92
85.09
88.27
91.44
94.62
97.79
100.97
104.14
107.32
110.49
113.67
116.84
120.02
123.19
126.37
129.54
132.72
135.89
139.07
142.24
145.42
148.59
151.77
158.12
164.47
170.82
177.17
183.52
189.87
196.22
202.57
208.92
215.27
221.62
227.97
234.32
240.67
247.02
253.37
266.07
278.77
291.47
C/S
± 0.46
± 0.46
± 0.51
± 0.51
± 0.51
± 0.51
± 0.61
± 0.61
± 0.61
± 0.61
± 0.61
± 0.71
± 0.71
± 0.71
± 0.71
± 0.71
± 0.76
± 0.76
± 0.76
± 0.76
± 0.76
± 0.76
± 0.94
± 0.94
± 0.94
± 0.94
± 0.94
± 0.94
± 0.94
± 0.94
± 0.94
± 1.02
± 1.02
± 1.02
± 1.02
± 1.14
± 1.14
± 1.14
± 1.14
± 1.27
± 1.27
± 1.27
± 1.27
± 1.40
± 1.40
± 1.40
± 1.40
± 1.52
± 1.52
± 1.65
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
www.hitechseals.com
9211 - 41 Avenue NW
780.438.6055
21
O-Ring Design Guide
Dash
Number
22
Nominal
Actual Sizing
I.D.
Metric Actual
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
I.D.
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
C/S
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
C/S
I.D.
11.975
12.975
13.975
14.975
15.955
16.955
17.955
18.952
19.952
20.952
21.952
22.940
23.940
24.940
25.940
± 0.065
± 0.065
± 0.070
± 0.070
± 0.075
± 0.080
± 0.085
± 0.090
± 0.095
± 0.095
± 0.100
± 0.105
± 0.110
± 0.115
± 0.120
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
0.210
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
304.17
329.57
354.97
380.37
405.26
430.66
456.06
481.38
506.78
532.18
557.58
582.68
608.08
633.48
658.88
± 1.65
± 1.65
± 1.78
± 1.78
± 1.91
± 2.03
± 2.16
± 2.29
± 2.41
± 2.41
± 2.54
± 2.67
± 2.79
± 2.92
± 3.05
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
C/S
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
4 - 1/2
4 - 5/8
4 - 3/4
4 - 7/8
5
5 - 1/8
5 - 1/4
5 - 3/8
5 - 1/2
5 - 5/8
5 - 3/4
5 - 7/8
6
6 - 1/4
6 - 1/2
6 - 3/4
7
7 - 1/4
7 - 1/2
7 - 3/4
8
8 - 1/2
9
9 - 1/2
10
10 - 1/2
11
11 - 1/2
12
12 - 1/2
13
13 - 1/2
14
14 - 1/2
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
4.475
4.600
4.725
4.850
4.975
5.100
5.225
5.350
5.475
5.600
5.725
5.850
5.975
6.225
6.475
6.725
6.975
7.225
7.475
7.725
7.975
8.475
8.975
9.475
9.975
10.475
10.975
11.475
11.975
12.475
12.975
13.475
13.975
14.475
± 0.033
± 0.033
± 0.033
± 0.033
± 0.037
± 0.037
± 0.037
± 0.037
± 0.037
± 0.037
± 0.037
± 0.037
± 0.037
± 0.040
± 0.040
± 0.040
± 0.040
± 0.045
± 0.045
± 0.045
± 0.045
± 0.055
± 0.055
± 0.055
± 0.055
± 0.060
± 0.060
± 0.060
± 0.060
± 0.060
± 0.060
± 0.070
± 0.070
± 0.070
0.275
0.275
0.275
0.275
0.275
0.275
0.275
0.275
0.275
0.275
0.275
0.275
0.275
0.275
0.275
0.275
0.275
0.275
0.275
0.275
0.275
0.275
0.275
0.275
0.275
0.275
0.275
0.275
0.275
0.275
0.275
0.275
0.275
0.275
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
113.67
116.84
120.02
123.19
126.37
129.54
132.72
135.89
139.07
142.24
145.42
148.59
151.77
158.12
164.47
170.82
177.17
183.52
189.87
196.22
202.57
215.27
227.97
240.67
253.37
266.07
278.77
291.47
304.17
316.87
329.57
342.27
354.97
367.67
± 0.84
± 0.84
± 0.84
± 0.84
± 0.94
± 0.94
± 0.94
± 0.94
± 0.94
± 0.94
± 0.94
± 0.94
± 0.94
± 1.02
± 1.02
± 1.02
± 1.02
± 1.14
± 1.14
± 1.14
± 1.14
± 1.40
± 1.40
± 1.40
± 1.40
± 1.52
± 1.52
± 1.52
± 1.52
± 1.52
± 1.52
± 1.78
± 1.78
± 1.78
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
9211 - 41 Avenue NW
780.438.6055
www.hitechseals.com
O-Ring Design Guide
Nominal
Dash
Number
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
I.D.
15
15 - 1/2
16
16 - 1/2
17
17 - 1/2
18
18 - 1/2
19
19 - 1/2
20
21
22
23
24
25
26
Actual Sizing
C/S
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
I.D.
14.975
15.475
15.955
16.455
16.955
17.455
17.955
18.455
18.955
19.455
19.955
20.955
21.955
22.940
23.940
24.940
25.940
Metric Actual
C/S
± 0.070
± 0.070
± 0.075
± 0.075
± 0.080
± 0.085
± 0.085
± 0.085
± 0.090
± 0.090
± 0.095
± 0.095
± 0.100
± 0.105
± 0.110
± 0.115
± 0.120
0.275
0.275
0.275
0.275
0.275
0.275
0.275
0.275
0.275
0.275
0.275
0.275
0.275
0.275
0.275
0.275
0.275
I.D.
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
± 0.006
380.37
393.07
405.26
417.96
430.66
443.36
456.06
468.76
481.46
494.16
506.86
532.26
557.66
582.68
608.08
633.48
658.88
C/S
± 1.78
± 1.78
± 1.91
± 1.91
± 2.03
± 2.16
± 2.16
± 2.16
± 2.29
± 2.29
± 2.41
± 2.41
± 2.54
± 2.67
± 2.79
± 2.92
± 3.05
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
± 0.15
ORB Series
Actual Sizing
Dash
Number
901
902
903
904
905
906
907
908
909
910
911
912
913
914
916
918
920
924
928
932
I.D.
0.185
0.239
0.301
0.351
0.414
0.468
0.530
0.644
0.706
0.755
0.863
0.924
0.986
1.048
1.171
1.355
1.475
1.720
2.090
2.337
Metric Actual
C/S
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.005
± 0.009
± 0.009
± 0.009
± 0.009
± 0.009
± 0.01
± 0.01
± 0.01
± 0.012
± 0.014
± 0.014
± 0.018
± 0.018
0.056
0.064
0.064
0.072
0.072
0.078
0.082
0.087
0.097
0.097
0.116
0.116
0.116
0.116
0.116
0.116
0.118
0.118
0.118
0.118
I.D.
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.003
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
± 0.004
4.70
6.07
7.65
8.92
10.52
11.89
13.46
16.36
17.93
19.18
21.92
23.47
25.04
26.62
29.74
34.42
37.47
43.69
53.09
59.36
C/S
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.13
± 0.23
± 0.23
± 0.23
± 0.23
± 0.23
± 0.25
± 0.25
± 0.25
± 0.30
± 0.36
± 0.36
± 0.36
± 0.36
1.42
1.63
1.63
1.83
1.83
1.98
2.08
2.21
2.46
2.46
2.95
2.95
2.95
2.95
2.95
2.95
3.00
3.00
3.00
3.00
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.08
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
± 0.10
Hi-Tech Seals offers O-rings in sizes ranging from 400-425. These O-ring size dimensions and tolerances are
unassigned under ISO 3601. In addition, Hi-Tech Seals stocks specific non-standard cross-section O-rings
such as 3/8”, 1/2” and 3/4”.
www.hitechseals.com
9211 - 41 Avenue NW
780.438.6055
23
O-Ring Design Guide
Metric O-Ring Sizes
I.D.
24
Part
Number
C/S
(mm)
I.D.
(mm)
1000115
1000125
100015
100018
10002
100025
100027
10003
100033
100035
10004
100045
10005
100055
10006
100065
10007
100072
100075
10008
100085
10009
100095
10010
100105
10011
100115
10012
100125
10013
100135
10014
100145
10015
100155
10016
100165
10017
10018
100185
10019
100195
10020
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.15
1.25
1.50
1.80
2.00
2.50
2.70
3.00
3.30
3.50
4.00
4.50
5.00
5.50
6.00
6.50
7.00
7.20
7.50
8.00
8.50
9.00
9.50
10.00
10.50
11.00
11.50
12.00
12.50
13.00
13.50
14.00
14.50
15.00
15.50
16.00
16.50
17.00
18.00
18.50
19.00
19.50
20.00
Cross
Ref. #
Part
Number
C/S
(mm)
I.D.
(mm)
100205
10021
100215
10022
100225
10023
100235
10024
100245
10025
10028
100294
100299
100305
100318
10032
10039
10042
10060
-001
120025
120026
120035
12005
12024
12026
12028
12035
12040
120535
12098
-002
150018
1500185
15002
150025
150028
15003
150035
15004
150045
15005
150055
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.02
1.20
1.20
1.20
1.20
1.20
1.20
1.20
1.20
1.20
1.20
1.20
1.27
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
20.50
21.00
21.50
22.00
22.50
23.00
23.50
24.00
24.50
25.00
28.00
29.40
29.90
30.50
31.80
32.00
39.00
42.00
60.00
0.74
2.50
2.60
3.50
5.00
24.00
26.00
28.00
35.00
40.00
53.50
98.00
1.07
1.80
1.85
2.00
2.50
2.80
3.00
3.50
4.00
4.50
5.00
5.50
Cross
Ref. #
-001
-002
S3
S4
S5
S6
C/S
Part
Number
C/S
(mm)
I.D.
(mm)
15006
150065
15007
150075
15008
150085
15009
150095
15010
150105
150107
15011
150115
15012
150125
15013
1501325
150135
15014
15015
150155
15016
150165
15017
150175
15018
150185
15019
150195
15020
150205
15021
150215
15022
150225
15023
150235
15024
150245
15025
150255
15026
150265
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
6.00
6.50
7.00
7.50
8.00
8.50
9.00
9.50
10.00
10.50
10.70
11.00
11.50
12.00
12.50
13.00
13.25
13.50
14.00
15.00
15.50
16.00
16.50
17.00
17.50
18.00
18.50
19.00
19.50
20.00
20.50
21.00
21.5
22.00
22.50
23.00
23.50
24.00
24.50
25.00
25.50
26.00
26.50
Cross
Ref. #
S7
S8
S9
S 10
S 11.2
S 12
S 12.5
S 14
S 16
S 18
S 20
S 22
9211 - 41 Avenue NW
780.438.6055
www.hitechseals.com
O-Ring Design Guide
Metric O-Ring Sizes
Part
Number
15027
150275
15028
150285
15029
150295
15030
150305
15031
150315
15032
150325
15033
150335
15034
150345
15035
150355
15036
150365
15037
150375
15038
150385
15039
150395
15040
15041
15042
15043
15044
15045
15046
15047
15048
15049
15050
15051
15052
15053
15054
15055
15056
15057
15058
15059
15060
15061
15062
15063
15064
C/S
(mm)
I.D.
(mm)
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
27.00
27.50
28.00
28.50
29.00
29.50
30.00
30.50
31.00
31.50
32.00
32.50
33.00
33.50
34.00
34.50
35.00
35.50
36.00
36.50
37.00
37.50
38.00
38.50
39.00
39.50
40.00
41.00
42.00
43.00
44.00
45.00
46.00
47.00
48.00
49.00
50.00
51.00
52.00
53.00
54.00
55.00
56.00
57.00
58.00
59.00
60.00
61.00
62.00
63.00
64.00
Cross
Ref. #
Part
Number
C/S
(mm)
I.D.
(mm)
15065
15066
15067
15068
15069
15070
15071
15072
15073
15074
15075
15076
15077
15078
15079
15080
15081
15082
15083
15084
15085
15086
15087
15088
15089
15090
15091
15092
15093
15094
15095
15096
15097
15098
15099
15100
15105
15145
-003
160022
1600275
160028
160031
160032
160037
160041
160047
160050
160051
160061
160068
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.52
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.60
65.00
66.00
67.00
68.00
69.00
70.00
71.00
72.00
73.00
74.00
75.00
76.00
77.00
78.00
79.00
80.00
81.00
82.00
83.00
84.00
85.00
86.00
87.00
88.00
89.00
90.00
91.00
92.00
93.00
94.00
95.00
96.00
97.00
98.00
99.00
100.00
105.00
145.00
1.42
2.20
2.75
2.80
3.10
3.20
3.70
4.10
4.70
5.00
5.10
6.10
6.80
Cross
Ref. #
-003
Part
Number
160071
160081
160091
160101
160111
160121
160131
160141
160151
160161
160171
160181
160191
160203
160211
160221
160251
160271
160291
160321
160351
160371
160511
160860
160966
16115
-004
-005
-006
-007
-008
-009
-010
-011
-012
-013
-014
-015
-016
-017
-018
-019
-020
-021
-022
-023
-024
-025
-026
-027
-028
C/S
(mm)
I.D.
(mm)
Cross
Ref. #
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
7.10
8.10
9.10
10.10
11.10
12.10
13.10
14.10
15.10
16.10
17.10
18.10
19.10
20.30
21.10
22.10
25.10
27.10
29.10
32.10
35.10
37.10
51.10
86.00
96.60
115.00
1.78
2.57
2.90
3.68
4.47
5.28
6.07
7.65
9.25
10.82
12.42
14.00
15.60
17.17
18.77
20.35
21.95
23.52
25.12
26.70
28.30
29.87
31.47
33.05
34.65
-004
-005
-006
-007
-008
-009
-010
-011
-012
-013
-014
-015
-016
-017
-018
-019
-020
-021
-022
-023
-024
-025
-026
-027
-028
www.hitechseals.com
9211 - 41 Avenue NW
780.438.6055
25
O-Ring Design Guide
Metric O-Ring Sizes
26
Part
Number
C/S
(mm)
I.D.
(mm)
Cross
Ref. #
Part
Number
-029
-030
-031
-032
-033
-034
-035
-036
-037
-038
-039
-040
-041
-042
-043
-044
-045
-046
-047
-048
-049
-050
180018
18002
1800224
180025
180028
1800315
1800355
1800375
18004
180045
1800487
18005
1800515
180053
180056
18006
180063
180067
180069
180071
180075
18008
180085
1800876
18009
180095
18010
180106
180112
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.78
1.80
1.80
1.80
1.80
1.80
1.80
1.80
1.80
1.80
1.80
1.80
1.80
1.80
1.80
1.80
1.80
1.80
1.80
1.80
1.80
1.80
1.80
1.80
1.80
1.80
1.80
1.80
1.80
1.80
37.82
41.00
44.17
47.35
50.52
53.70
56.87
60.05
63.22
66.40
69.57
72.75
75.92
82.27
88.62
94.97
101.32
107.67
114.02
120.37
126.72
133.07
1.80
2.00
2.24
2.50
2.80
3.15
3.55
3.75
4.00
4.50
4.87
5.00
5.15
5.30
5.60
6.00
6.30
6.70
6.90
7.10
7.50
8.00
8.50
8.76
9.00
9.50
10.00
10.60
11.20
-029
-030
-031
-032
-033
-034
-035
-036
-037
-038
-039
-040
-041
-042
-043
-044
-045
-046
-047
-048
-049
-050
180118
180125
180132
18014
18015
18016
18017
190024
190026
190028
190034
190037
190038
190042
190048
190049
190057
190058
190064
190068
190072
190078
19008
190088
190089
190098
20002
200025
200026
20003
200035
20004
200045
200046
20005
200055
20006
200065
20007
200075
20008
200085
20009
200094
20010
200105
20011
200115
20012
200125
20013
C/S
(mm)
I.D.
(mm)
1.80
1.80
1.80
1.80
1.80
1.80
1.80
1.90
1.90
1.90
1.90
1.90
1.90
1.90
1.90
1.90
1.90
1.90
1.90
1.90
1.90
1.90
1.90
1.90
1.90
1.90
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
11.80
12.50
13.20
14.00
15.00
16.00
17.00
2.40
2.60
2.80
3.40
3.70
3.80
4.20
4.80
4.90
5.70
5.80
6.40
6.80
7.20
7.80
8.00
8.80
8.90
9.80
2.00
2.50
2.60
3.00
3.50
4.00
4.50
4.60
5.00
5.50
6.00
6.50
7.00
7.50
8.00
8.50
9.00
9.40
10.00
10.50
11.00
11.50
12.00
12.50
13.00
Cross
Ref. #
P3
P4
P5
P6
P7
P8
P9
P 10
Part
Number
200135
20014
200145
20015
200155
20016
200165
20017
200175
20018
200185
20019
200195
20020
200205
20021
200215
200219
20022
200225
20023
200235
20024
200245
20025
200255
20026
200265
20027
200275
20028
200285
20029
200295
20030
200305
20031
200315
20032
200325
20033
200335
20034
200345
20035
200355
20036
200365
20037
200375
20038
C/S
(mm)
I.D.
(mm)
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
13.50
14.00
14.50
15.00
15.50
16.00
16.50
17.00
17.50
18.00
18.50
19.00
19.50
20.00
20.50
21.00
21.50
21.90
22.00
22.50
23.00
23.50
24.00
24.50
25.00
25.50
26.00
26.50
27.00
27.50
28.00
28.50
29.00
29.50
30.00
30.50
31.00
31.50
32.00
32.50
33.00
33.50
34.00
34.50
35.00
35.50
36.00
36.50
37.00
37.50
38.00
Cross
Ref. #
S 22.4
S 24
S 25
S 26
S 28
S 29
S 30
S 31.5
S 32
S 34
S 35
S 35.5
S 36
S 38
9211 - 41 Avenue NW
780.438.6055
www.hitechseals.com
O-Ring Design Guide
Metric O-Ring Sizes
Part
Number
20039
200395
20040
20041
200415
20042
20043
200435
20044
200445
20045
200455
20046
20047
200475
20048
20049
200495
20050
20051
20052
200525
20053
20054
200545
20055
200555
20056
20057
20058
20059
200595
20060
20061
20062
200625
20063
20064
200645
20065
20066
200665
20067
20068
20069
200695
20070
200705
20071
20072
20073
C/S
(mm)
I.D.
(mm)
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
39.00
39.50
40.00
41.00
41.50
42.00
43.00
43.50
44.00
44.50
45.00
45.50
46.00
47.00
47.50
48.00
49.00
49.50
50.00
51.00
52.00
52.50
53.00
54.00
54.50
55.00
55.50
56.00
57.00
58.00
59.00
59.50
60.00
61.00
62.00
62.50
63.00
64.00
64.50
65.00
66.00
66.50
67.00
68.00
69.00
69.50
70.00
70.50
71.00
72.00
73.00
Cross
Ref. #
S 40
S 42
S 44
S 45
S 46
S 48
S 50
S 53
S 55
S 56
S 60
S 63
S 65
S 67
S 70
S 71
Part
Number
20074
200745
20075
20076
20077
20078
20079
200795
20080
20081
20082
20083
20084
200845
20085
20086
20087
20088
20089
200895
20090
20091
20092
20093
20094
200945
20095
20096
20097
20098
20099
200995
20100
20102
201045
20105
20109
201095
20110
201115
201145
20115
201195
20120
201245
201256
201295
20130
201315
201345
201395
C/S
(mm)
I.D.
(mm)
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
74.00
74.50
75.00
76.00
77.00
78.00
79.00
79.50
80.00
81.00
82.00
83.00
84.00
84.50
85.00
86.00
87.00
88.00
89.00
89.50
90.00
91.00
92.00
93.00
94.00
94.50
95.00
96.00
97.00
98.00
99.00
99.50
100.00
102.00
104.50
105.00
109.00
109.50
110.00
111.50
114.50
115.00
119.50
120.00
124.50
125.60
129.50
130.00
131.50
134.50
139.50
Cross
Ref. #
S 75
S 80
S 85
S 90
S 95
S 100
S 105
S 110
S 112
S 115
S 120
S 125
S 130
S 132
S 135
S 140
Part
Number
20140
201445
201495
20165
20180
20194
240033
240036
240043
240046
240053
240055
240056
240063
240066
240073
240075
240076
24008
240083
240086
240093
240096
240098
240103
240105
240106
240108
24011
240113
240115
240116
240118
240123
240126
240133
240135
240136
240138
240143
240145
240146
240148
240153
240155
240156
240158
240159
240163
240166
240173
C/S
(mm)
I.D.
(mm)
2.00
2.00
2.00
2.00
2.00
2.00
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
140.00
144.50
149.50
165.00
180.00
194.00
3.30
3.60
4.30
4.60
5.30
5.50
5.60
6.30
6.60
7.30
7.50
7.60
8.00
8.30
8.60
9.30
9.60
9.80
10.30
10.50
10.60
10.80
11.00
11.30
11.50
11.60
11.80
12.30
12.60
13.30
13.50
13.60
13.80
14.30
14.50
14.60
14.80
15.30
15.50
15.60
15.80
15.90
16.30
16.60
17.30
Cross
Ref. #
S 145
S 150
P 10A
P 11
P 11.2
P 12
P 12.5
P 14
P 15
P 16
www.hitechseals.com
9211 - 41 Avenue NW
780.438.6055
27
O-Ring Design Guide
Metric O-Ring Sizes
Part
Number
240175
240176
240178
240183
240186
240193
240196
240198
240203
240205
240208
240213
240215
240216
240218
240223
240226
240233
240235
240236
240243
240245
240246
24025
240253
240256
240273
240275
240276
240296
240303
240316
240333
240346
240365
240376
240396
240416
240446
240476
240496
240516
240546
240576
240596
240616
240646
240676
240696
25004
250046
28
C/S
(mm)
I.D.
(mm)
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.50
2.50
17.50
17.60
17.80
18.30
18.60
19.30
19.60
19.80
20.30
20.50
20.80
21.30
21.50
21.60
21.80
22.30
22.60
23.30
23.50
23.60
24.30
24.50
24.60
25.00
25.30
25.60
27.30
27.50
27.60
29.60
30.30
31.60
33.30
34.60
36.50
37.60
39.60
41.60
44.60
47.60
49.60
51.60
54.60
57.60
59.60
61.60
64.60
67.60
69.60
4.00
4.60
Cross
Ref. #
P 18
P 20
P 21
P 22
Part
Number
25005
250055
25006
250065
25007
250075
25008
250085
25009
250095
25010
250105
25011
250115
25012
250125
25013
250135
25014
250145
25015
250155
25016
250165
25017
250175
25018
250185
25019
250195
25020
250205
25021
250215
25022
250225
25023
250235
25024
250245
25025
250255
25026
250265
25027
250275
25028
250285
25029
250295
25030
C/S
(mm)
I.D.
(mm)
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
5.00
5.50
6.00
6.50
7.00
7.50
8.00
8.50
9.00
9.50
10.00
10.50
11.00
11.50
12.00
12.50
13.00
13.50
14.00
14.50
15.00
15.50
16.00
16.50
17.00
17.50
18.00
18.50
19.00
19.50
20.00
20.50
21.00
21.50
22.00
22.50
23.00
23.50
24.00
24.50
25.00
25.50
26.00
26.50
27.00
27.50
28.00
28.50
29.00
29.50
30.00
Cross
Ref. #
Part
Number
250305
25031
250315
25032
250325
25033
250335
25034
250345
25035
250355
25036
250365
25037
250375
25038
250385
25039
250395
25040
25041
25042
25043
25044
25045
25046
25047
25048
25049
25050
25051
25052
25053
25054
25055
25056
25057
25058
25059
25060
25061
25062
25063
25064
25065
25066
25067
25068
25069
25070
25071
C/S
(mm)
I.D.
(mm)
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
30.50
31.00
31.50
32.00
32.50
33.00
33.50
34.00
34.50
35.00
35.50
36.00
36.50
37.00
37.50
38.00
38.50
39.00
39.50
40.00
41.00
42.00
43.00
44.00
45.00
46.00
47.00
48.00
49.00
50.00
51.00
52.00
53.00
54.00
55.00
56.00
57.00
58.00
59.00
60.00
61.00
62.00
63.00
64.00
65.00
66.00
67.00
68.00
69.00
70.00
71.00
Cross
Ref. #
9211 - 41 Avenue NW
780.438.6055
www.hitechseals.com
O-Ring Design Guide
Metric O-Ring Sizes
Part
Number
25072
25073
25074
25075
25076
25077
25078
25079
25080
25081
25082
25083
25084
25085
25086
25087
25088
25089
25090
25091
25092
25093
25094
25095
25096
25097
25098
25099
25100
25101
25102
25103
25104
25105
25106
25107
25108
25109
25110
25111
25112
25113
25114
25115
25116
25117
25118
25119
25120
25121
25122
C/S
(mm)
I.D.
(mm)
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
72.00
73.00
74.00
75.00
76.00
77.00
78.00
79.00
80.00
81.00
82.00
83.00
84.00
85.00
86.00
87.00
88.00
89.00
90.00
91.00
92.00
93.00
94.00
95.00
96.00
97.00
98.00
99.00
100.00
101.00
102.00
103.00
104.00
105.00
106.00
107.00
108.00
109.00
110.00
111.00
112.00
113.00
114.00
115.00
116.00
117.00
118.00
119.00
120.00
121.00
122.00
Cross
Ref. #
Part
Number
25123
25124
25125
25126
25127
25128
25129
25130
25131
25132
25133
25134
25135
25136
25137
25138
25139
25140
25141
25142
25143
25144
25145
25146
25147
25148
25149
25150
-102
-103
-104
-105
-106
-107
-108
-109
-110
-111
-112
-113
-114
-115
-116
-117
-118
-119
-120
-121
-122
-123
-124
C/S
(mm)
I.D.
(mm)
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
123.00
124.00
125.00
126.00
127.00
128.00
129.00
130.00
131.00
132.00
133.00
134.00
135.00
136.00
137.00
138.00
139.00
140.00
141.00
142.00
143.00
144.00
145.00
146.00
147.00
148.00
149.00
150.00
1.24
2.06
2.84
3.63
4.42
5.23
6.02
7.59
9.19
10.77
12.37
13.94
15.54
17.12
18.72
20.30
21.89
23.47
25.07
26.64
28.24
29.82
31.42
Cross
Ref. #
Part
Number
-102
-103
-104
-105
-106
-107
-108
-109
-110
-111
-112
-113
-114
-115
-116
-117
-118
-119
-120
-121
-122
-123
-124
-125
-126
-127
-128
-129
-130
-131
-132
-133
-134
-135
-136
-137
-138
-139
-140
-141
-142
-143
-144
-145
-146
-147
-148
-149
-150
-151
-152
-153
-154
-155
-156
-157
-158
-159
-160
-161
-162
-163
-164
-165
-166
-167
-168
-169
-170
-171
-172
-173
-174
-175
C/S
(mm)
I.D.
(mm)
Cross
Ref. #
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
2.62
32.99
34.59
36.17
37.77
39.34
40.94
42.52
44.12
45.69
47.29
48.90
50.47
52.07
53.64
55.25
56.82
58.42
59.99
61.60
63.17
64.77
66.34
67.95
69.52
71.12
72.69
75.87
82.22
88.57
94.92
101.27
107.62
113.97
120.32
126.67
133.02
139.37
145.72
152.07
158.42
164.77
171.12
177.47
183.82
190.17
196.52
202.87
209.22
215.57
221.92
228.27
-125
-126
-127
-128
-129
-130
-131
-132
-133
-134
-135
-136
-137
-138
-139
-140
-141
-142
-143
-144
-145
-146
-147
-148
-149
-150
-151
-152
-153
-154
-155
-156
-157
-158
-159
-160
-161
-162
-163
-164
-165
-166
-167
-168
-169
-170
-171
-172
-173
-174
-175
www.hitechseals.com
9211 - 41 Avenue NW
780.438.6055
29
O-Ring Design Guide
Metric O-Ring Sizes
30
Part
Number
C/S
(mm)
I.D.
(mm)
Cross
Ref. #
Part
Number
-176
-177
-178
265014
265015
265016
265017
265018
265019
265020
2650212
2650224
2650236
265025
2650258
2650265
265028
265030
2650315
265032
2650325
2650335
2650345
2650355
2650365
2650375
2650387
300035
30004
300045
30005
300055
30006
300065
30007
300075
30008
300085
30009
300095
30010
300105
30011
300115
30012
300125
30013
300135
30014
300145
30015
2.62
2.62
2.62
2.65
2.65
2.65
2.65
2.65
2.65
2.65
2.65
2.65
2.65
2.65
2.65
2.65
2.65
2.65
2.65
2.65
2.65
2.65
2.65
2.65
2.65
2.65
2.65
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
234.62
240.97
247.32
14.00
15.00
16.00
17.00
18.00
19.00
20.00
21.20
22.40
23.60
25.00
25.80
26.50
28.00
30.00
31.50
32.00
32.50
33.50
34.50
35.50
36.50
37.50
38.70
3.50
4.00
4.50
5.00
5.50
6.00
6.50
7.00
7.50
8.00
8.50
9.00
9.50
10.00
10.50
11.00
11.50
12.00
12.50
13.00
13.50
14.00
14.50
15.00
-176
-177
-178
300155
30016
300165
30017
300175
30018
300182
300185
30019
300192
300195
30020
300205
30021
300215
30022
300222
300225
30023
300235
30024
300242
300245
300246
30025
300252
300255
30026
300262
300265
30027
300275
30028
300285
30029
300292
300295
30030
300302
300305
30031
300315
30032
300322
300325
30033
300335
30034
300342
300345
30035
C/S
(mm)
I.D.
(mm)
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
15.50
16.00
16.50
17.00
17.50
18.00
18.20
18.50
19.00
19.20
19.50
20.00
20.50
21.00
21.50
22.00
22.20
22.50
23.00
23.50
24.00
24.20
24.50
24.60
25.00
25.20
25.50
26.00
26.20
26.50
27.00
27.50
28.00
28.50
29.00
29.20
29.50
30.00
30.20
30.50
31.00
31.50
32.00
32.20
32.50
33.00
33.50
34.00
34.20
34.50
35.00
Cross
Ref. #
Part
Number
300355
30036
300362
300365
30037
300372
300375
30038
300385
30039
300392
300395
30040
300402
30041
300415
30042
300422
300425
30043
30044
300442
300445
30045
30046
30047
30048
30049
300495
30050
300505
30051
30052
30053
30054
300542
300545
30055
30056
300562
30057
30058
30059
300595
30060
30061
30062
300622
30063
30064
300645
C/S
(mm)
I.D.
(mm)
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
35.50
36.00
36.20
36.50
37.00
37.20
37.50
38.00
38.50
39.00
39.20
39.50
40.00
40.20
41.00
41.50
42.00
42.20
42.50
43.00
44.00
44.20
44.50
45.00
46.00
47.00
48.00
49.00
49.50
50.00
50.50
51.00
52.00
53.00
54.00
54.20
54.50
55.00
56.00
56.20
57.00
58.00
59.00
59.50
60.00
61.00
62.00
62.20
63.00
64.00
64.50
Cross
Ref. #
9211 - 41 Avenue NW
780.438.6055
www.hitechseals.com
O-Ring Design Guide
Metric O-Ring Sizes
Part
Number
30065
30066
30067
30068
30069
30070
30071
30072
30073
30074
30075
30076
30077
30078
30079
30080
30081
30082
30083
30084
300845
30085
30086
30087
30088
30089
300895
30090
30091
30092
30093
30094
300945
30095
30096
30097
30098
30099
300995
30100
30101
30102
30103
30104
301045
30105
30106
30107
30108
30109
301095
C/S
(mm)
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
I.D.
(mm)
65.00
66.00
67.00
68.00
69.00
70.00
71.00
72.00
73.00
74.00
75.00
76.00
77.00
78.00
79.00
80.00
81.00
82.00
83.00
84.00
84.50
85.00
86.00
87.00
88.00
89.00
89.50
90.00
91.00
92.00
93.00
94.00
94.50
95.00
96.00
97.00
98.00
99.00
99.50
100.00
101.00
102.00
103.00
104.00
104.50
105.00
106.00
107.00
108.00
109.00
109.50
Cross
Ref. #
Part
Number
30110
30111
30112
30113
30114
301145
30115
30116
30117
30118
30119
301195
30120
30121
30122
30123
30124
301245
30125
30126
301265
30127
30128
30129
301295
30130
30131
30132
30133
30134
301345
30135
30136
30137
30138
30139
301395
30140
30141
30142
30143
30144
301445
30145
30146
30147
30148
30149
301495
30150
30151
C/S
(mm)
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
I.D.
(mm)
110.00
111.00
112.00
113.00
114.00
114.50
115.00
116.00
117.00
118.00
119.00
119.50
120.00
121.00
122.00
123.00
124.00
124.50
125.00
126.00
126.50
127.00
128.00
129.00
129.50
130.00
131.00
132.00
133.00
134.00
134.50
135.00
136.00
137.00
138.00
139.00
139.50
140.00
141.00
142.00
143.00
144.00
144.50
145.00
146.00
147.00
148.00
149.00
149.50
150.00
151.00
Cross
Ref. #
Part
Number
30152
30153
30154
301545
30155
30156
30157
30158
30159
301595
30160
30161
30162
30163
30164
301645
30165
30166
30167
30168
30169
301695
30170
30171
30172
30173
30174
301745
30175
30176
30177
30178
30179
301795
30180
30181
30182
30183
301835
30184
301845
30185
30186
30187
30188
30189
301895
30190
30191
30192
30193
C/S
(mm)
I.D.
(mm)
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
152.00
153.00
154.00
154.50
155.00
156.00
157.00
158.00
159.00
159.50
160.00
161.00
162.00
163.00
164.00
164.50
165.00
166.00
167.00
168.00
169.00
169.50
170.00
171.00
172.00
173.00
174.00
174.50
175.00
176.00
177.00
178.00
179.00
179.50
180.00
181.00
182.00
183.00
183.50
184.00
184.50
185.00
186.00
187.00
188.00
189.00
189.50
190.00
191.00
192.00
193.00
Cross
Ref. #
www.hitechseals.com
9211 - 41 Avenue NW
780.438.6055
31
O-Ring Design Guide
Metric O-Ring Sizes
Part
Number
30194
301945
30195
30196
30197
30198
30199
301995
30200
310244
310294
310344
310394
310444
310494
310544
310594
310644
310694
310744
310794
310844
310894
310944
310994
311044
311094
311144
311194
311244
311294
311344
311394
311444
35005
35008
35009
350092
35010
35011
35012
35013
35014
35015
35016
35017
350175
35018
35019
35020
35021
32
C/S
(mm)
I.D.
(mm)
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.10
3.10
3.10
3.10
3.10
3.10
3.10
3.10
3.10
3.10
3.10
3.10
3.10
3.10
3.10
3.10
3.10
3.10
3.10
3.10
3.10
3.10
3.10
3.10
3.10
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
194.00
194.50
195.00
196.00
197.00
198.00
199.00
199.50
200.00
24.40
29.40
34.40
39.40
44.40
49.40
54.40
59.40
64.40
69.40
74.40
79.40
84.40
89.40
94.40
99.40
104.40
109.40
114.40
119.40
124.40
129.40
134.40
139.40
144.40
5.00
8.00
9.00
9.20
10.00
11.00
12.00
13.00
14.00
15.00
16.00
17.00
17.50
18.00
19.00
20.00
21.00
Cross
Ref. #
G 25
G 30
G 35
G 40
G 45
G 50
G 55
G 60
G 65
G 70
G 75
G 80
G 85
G 90
G 95
G 100
G 105
G 110
G 115
G 120
G 125
G 130
G 135
G 140
G 145
Part
Number
350217
35022
350221
35023
350237
35024
350247
35025
350252
350257
35026
35027
350277
35028
350287
35029
350292
350297
35030
350305
350307
35031
350312
350317
35032
35033
350337
35034
350347
35035
350352
350357
35036
35037
350377
35038
350387
35039
350397
35040
350407
35041
350417
35042
35043
350437
35044
350447
35045
350457
35046
C/S
(mm)
I.D.
(mm)
Cross
Ref. #
Part
Number
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
21.70
22.00
22.10
23.00
23.70
24.00
24.70
25.00
25.20
25.70
26.00
27.00
27.70
28.00
28.70
29.00
29.20
29.70
30.00
30.50
30.70
31.00
31.20
31.70
32.00
33.00
33.70
34.00
34.70
35.00
35.20
35.70
36.00
37.00
37.70
38.00
38.70
39.00
39.70
40.00
40.70
41.00
41.70
42.00
43.00
43.70
44.00
44.70
45.00
45.70
46.00
P 22A
35047
350477
35048
350487
35049
350497
35050
35051
35052
35053
35054
35055
35056
35057
35058
35059
35060
35061
35062
35063
35064
35065
35066
35067
35068
35069
35070
35071
35072
35073
35074
35075
35076
35077
35078
35079
35080
35081
35082
35083
35084
35085
35086
35087
35088
35089
35090
35091
35092
35093
35094
P 22.4
P 24
P 25
P 25.5
P 26
P 28
P 29
P 29.5
P 30
P 31
P 31.5
P 32
P 34
P 35
P 35.5
P 36
P 38
P 39
P 40
P 41
P 42
P 44
P 45
P 46
C/S
(mm)
I.D.
(mm)
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
47.00
47.70
48.00
48.70
49.00
49.70
50.00
51.00
52.00
53.00
54.00
55.00
56.00
57.00
58.00
59.00
60.00
61.00
62.00
63.00
64.00
65.00
66.00
67.00
68.00
69.00
70.00
71.00
72.00
73.00
74.00
75.00
76.00
77.00
78.00
79.00
80.00
81.00
82.00
83.00
84.00
85.00
86.00
87.00
88.00
89.00
90.00
91.00
92.00
93.00
94.00
Cross
Ref. #
P 48
P 49
P 50
9211 - 41 Avenue NW
780.438.6055
www.hitechseals.com
O-Ring Design Guide
Metric O-Ring Sizes
Part
Number
35095
35096
35097
35098
35099
35100
35101
35102
35103
35104
35105
35106
35107
35108
35109
35110
35111
35112
35113
35114
35115
35116
35117
35118
35119
35120
35121
35122
35123
35124
35125
35126
35127
35128
35129
35130
35131
35132
35133
35134
35135
35136
35137
35138
35139
35140
35141
35142
35143
35144
35145
C/S
(mm)
I.D.
(mm)
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
95.00
96.00
97.00
98.00
99.00
100.00
101.00
102.00
103.00
104.00
105.00
106.00
107.00
108.00
109.00
110.00
111.00
112.00
113.00
114.00
115.00
116.00
117.00
118.00
119.00
120.00
121.00
122.00
123.00
124.00
125.00
126.00
127.00
128.00
129.00
130.00
131.00
132.00
133.00
134.00
135.00
136.00
137.00
138.00
139.00
140.00
141.00
142.00
143.00
144.00
145.00
Cross
Ref. #
Part
Number
35146
35147
35148
35149
35150
35151
35152
35153
35154
35155
35156
35157
35158
35159
35160
35161
35162
35163
35164
35165
35166
35167
35168
35169
35170
35171
35172
35173
35174
35175
35176
35177
35178
35179
35180
35181
35182
35183
35184
35185
35186
35187
35188
35189
35190
35191
35192
35193
35194
35195
35196
C/S
(mm)
I.D.
(mm)
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
146.00
147.00
148.00
149.00
150.00
151.00
152.00
153.00
154.00
155.00
156.00
157.00
158.00
159.00
160.00
161.00
162.00
163.00
164.00
165.00
166.00
167.00
168.00
169.00
170.00
171.00
172.00
173.00
174.00
175.00
176.00
177.00
178.00
179.00
180.00
181.00
182.00
183.00
184.00
185.00
186.00
187.00
188.00
189.00
190.00
191.00
192.00
193.00
194.00
195.00
196.00
Cross
Ref. #
Part
Number
35197
35198
35199
35200
-201
-202
-203
-204
-205
-206
-207
-208
-209
-210
-211
-212
-213
-214
-215
-216
-217
-218
-219
-220
-221
-222
-223
-224
-225
-226
-227
-228
-229
-230
-231
-232
-233
-234
-235
-236
-237
-238
-239
-240
-241
-242
-243
-244
-245
-246
-247
C/S
(mm)
I.D.
(mm)
Cross
Ref. #
3.50
3.50
3.50
3.50
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
197.00
198.00
199.00
200.00
4.34
5.94
7.52
9.12
10.69
12.29
13.87
15.47
17.04
18.64
20.22
21.82
23.39
24.99
26.57
28.17
29.74
31.34
32.92
34.52
36.09
37.69
40.87
44.04
47.22
50.39
53.57
56.74
59.92
63.09
66.27
69.44
72.62
75.79
78.97
82.14
85.32
88.49
91.67
94.84
98.02
101.19
104.37
107.54
110.72
113.89
117.07
-201
-202
-203
-204
-205
-206
-207
-208
-209
-210
-211
-212
-213
-214
-215
-216
-217
-218
-219
-220
-221
-222
-223
-224
-225
-226
-227
-228
-229
-230
-231
-232
-233
-234
-235
-236
-237
-238
-239
-240
-241
-242
-243
-244
-245
-246
-247
www.hitechseals.com
9211 - 41 Avenue NW
780.438.6055
33
O-Ring Design Guide
Metric O-Ring Sizes
Part
Number
-248
-249
-250
-251
-252
-253
-254
-255
-256
-257
-258
-259
-260
-261
-262
-263
-264
-265
-266
-267
-268
-269
-270
-271
-272
-273
-274
-275
-276
-277
-278
-279
-280
-281
-282
-283
-284
360183
360198
360213
36023
360246
360262
360278
360293
360308
360325
360341
360356
360373
360434
34
C/S
(mm)
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.53
3.60
3.60
3.60
3.60
3.60
3.60
3.60
3.60
3.60
3.60
3.60
3.60
3.60
3.60
I.D.
(mm)
120.24
123.42
126.59
129.77
132.94
136.12
139.29
142.47
145.64
148.82
151.99
158.34
164.69
171.04
177.39
183.74
190.09
196.44
202.79
209.14
215.49
221.84
228.19
234.54
240.89
247.24
253.59
266.29
278.99
291.69
304.39
329.79
355.19
380.59
405.26
430.68
456.06
18.30
19.80
21.30
23.00
24.60
26.20
27.80
29.30
30.80
32.50
34.10
35.60
37.30
43.40
Cross
Ref. #
-248
-249
-250
-251
-252
-253
-254
-255
-256
-257
-258
-259
-260
-261
-262
-263
-264
-265
-266
-267
-268
-269
-270
-271
-272
-273
-274
-275
-276
-277
-278
-279
-280
-281
-282
-283
-284
Part
Number
40004
40005
40006
40007
40008
40009
40010
40011
40012
40013
40014
400145
40015
40016
40017
40018
40019
40020
40021
40022
40023
400235
40024
40025
40026
40027
40028
40029
40030
40031
40032
40033
400335
40034
40035
400355
40036
40037
40038
40039
400395
40040
40041
40042
40043
40044
40045
40046
40047
40048
40049
C/S
(mm)
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
I.D.
(mm)
4.00
5.00
6.00
7.00
8.00
9.00
10.00
11.00
12.00
13.00
14.00
14.50
15.00
16.00
17.00
18.00
19.00
20.00
21.00
22.00
23.00
23.50
24.00
25.00
26.00
27.00
28.00
29.00
30.00
31.00
32.00
33.00
33.50
34.00
35.00
35.50
36.00
37.00
38.00
39.00
39.50
40.00
41.00
42.00
43.00
44.00
45.00
46.00
47.00
48.00
49.00
Cross
Ref. #
V 15
V 24
V 34
V 36
V 40
Part
Number
40050
40051
40052
40053
40054
400545
40055
40056
40057
40058
40059
40060
40061
40062
40063
40064
40065
40066
40067
40068
40069
40070
40071
40072
40073
40074
40075
40076
40077
40078
40079
40080
40081
40082
40083
40084
40085
40086
40087
40088
40089
40090
40091
40092
40093
40094
40109
40110
40111
40112
40113
C/S
(mm)
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
I.D.
(mm)
50.00
51.00
52.00
53.00
54.00
54.50
55.00
56.00
57.00
58.00
59.00
60.00
61.00
62.00
63.00
64.00
65.00
66.00
67.00
68.00
69.00
70.00
71.00
72.00
73.00
74.00
75.00
76.00
77.00
78.00
79.00
80.00
81.00
82.00
83.00
84.00
85.00
86.00
87.00
88.00
89.00
90.00
91.00
92.00
93.00
94.00
109.00
110.00
111.00
112.00
113.00
Cross
Ref. #
V 55
V 70
V 85
9211 - 41 Avenue NW
780.438.6055
www.hitechseals.com
O-Ring Design Guide
Metric O-Ring Sizes
Part
Number
40114
40115
40116
40117
40118
40119
40120
40121
40122
40123
40124
40125
40126
40127
40128
40129
40130
40131
40132
40133
40134
40135
40136
40137
40138
40139
40140
40141
40142
40143
40144
40145
40146
40147
40148
401485
40149
40150
40151
40152
40153
40154
40155
40156
40157
40158
40159
40160
40161
40162
40163
C/S
(mm)
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
I.D.
(mm)
114.00
115.00
116.00
117.00
118.00
119.00
120.00
121.00
122.00
123.00
124.00
125.00
126.00
127.00
128.00
129.00
130.00
131.00
132.00
133.00
134.00
135.00
136.00
137.00
138.00
139.00
140.00
141.00
142.00
143.00
144.00
145.00
146.00
147.00
148.00
148.50
149.00
150.00
151.00
152.00
153.00
154.00
155.00
156.00
157.00
158.00
159.00
160.00
161.00
162.00
163.00
Cross
Ref. #
V 120
V 150
Part
Number
40164
40165
40166
40167
40168
40169
40170
40171
40172
40173
40174
40175
40176
40177
40178
40179
40180
40181
40182
40183
40184
40185
40186
40187
40188
40189
40190
40191
40192
40193
40194
40195
40196
40197
40198
40199
40200
40201
40202
40203
40204
40205
40206
40207
40208
40209
40210
45006
45008
45009
45010
C/S
(mm)
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.50
4.50
4.50
4.50
I.D.
(mm)
164.00
165.00
166.00
167.00
168.00
169.00
170.00
171.00
172.00
173.00
174.00
175.00
176.00
177.00
178.00
179.00
180.00
181.00
182.00
183.00
184.00
185.00
186.00
187.00
188.00
189.00
190.00
191.00
192.00
193.00
194.00
195.00
196.00
197.00
198.00
199.00
200.00
201.00
202.00
203.00
204.00
205.00
206.00
207.00
208.00
209.00
210.00
6.00
8.00
9.00
10.00
Cross
Ref. #
V175
Part
Number
45011
45012
45013
45015
45016
45017
45018
45019
45020
45021
45022
45023
45024
45025
45026
45028
45029
45030
45031
45032
45033
45034
45035
45036
45037
45038
45039
45040
45041
45042
45043
45044
45045
45046
45047
45048
45049
45050
45051
45053
45056
45057
45060
45061
45062
45063
45064
45065
45066
45068
45069
C/S
(mm)
I.D.
(mm)
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
11.00
12.00
13.00
15.00
16.00
17.00
18.00
19.00
20.00
21.00
22.00
23.00
24.00
25.00
26.00
28.00
29.00
30.00
31.00
32.00
33.00
34.00
35.00
36.00
37.00
38.00
39.00
40.00
41.00
42.00
43.00
44.00
45.00
46.00
47.00
48.00
49.00
50.00
51.00
53.00
56.00
57.00
60.00
61.00
62.00
63.00
64.00
65.00
66.00
68.00
69.00
Cross
Ref. #
www.hitechseals.com
9211 - 41 Avenue NW
780.438.6055
35
O-Ring Design Guide
Metric O-Ring Sizes
Part
Number
45070
45071
45073
45074
45075
45076
45080
45081
45083
45085
45086
45089
45090
45092
45095
45098
45100
45101
45105
45106
45110
45115
45118
45120
45122
45124
45126
45128
45130
45137
45140
45150
45153
45155
45157
45160
45165
50004
50005
50006
50007
50008
50009
50010
50011
50012
50013
50014
50015
50016
50017
36
C/S
(mm)
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
I.D.
(mm)
70.00
71.00
73.00
74.00
75.00
76.00
80.00
81.00
83.00
85.00
86.00
89.00
90.00
92.00
95.00
98.00
100.00
101.00
105.00
106.00
110.00
115.00
118.00
120.00
122.00
124.00
126.00
128.00
130.00
137.00
140.00
150.00
153.00
155.00
157.00
160.00
165.00
4.00
5.00
6.00
7.00
8.00
9.00
10.00
11.00
12.00
13.00
14.00
15.00
16.00
17.00
Cross
Ref. #
Part
Number
50018
50019
50020
50021
50022
50023
50024
50025
50026
50027
50028
50029
50030
50031
50032
50033
50034
50035
50036
50037
50038
50039
50040
50041
50042
50043
50044
50045
50046
50047
50048
50049
50050
50051
50052
50053
50054
50055
50056
50057
50058
50059
50060
50061
50062
50063
50064
50065
50066
50067
50068
C/S
(mm)
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
I.D.
(mm)
18.00
19.00
20.00
21.00
22.00
23.00
24.00
25.00
26.00
27.00
28.00
29.00
30.00
31.00
32.00
33.00
34.00
35.00
36.00
37.00
38.00
39.00
40.00
41.00
42.00
43.00
44.00
45.00
46.00
47.00
48.00
49.00
50.00
51.00
52.00
53.00
54.00
55.00
56.00
57.00
58.00
59.00
60.00
61.00
62.00
63.00
64.00
65.00
66.00
67.00
68.00
Cross
Ref. #
Part
Number
50069
50070
50071
50072
50073
50074
50075
50076
50077
50078
50079
50080
50081
50082
50083
50084
50085
50086
50087
50088
50089
50090
50091
50092
50093
50094
50095
50096
50097
50098
50099
50100
50101
50102
50103
50104
50105
50106
50107
50108
50109
50110
50111
50112
50113
50114
50115
50116
50117
50118
50119
C/S
(mm)
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
I.D.
(mm)
69.00
70.00
71.00
72.00
73.00
74.00
75.00
76.00
77.00
78.00
79.00
80.00
81.00
82.00
83.00
84.00
85.00
86.00
87.00
88.00
89.00
90.00
91.00
92.00
93.00
94.00
95.00
96.00
97.00
98.00
99.00
100.00
101.00
102.00
103.00
104.00
105.00
106.00
107.00
108.00
109.00
110.00
111.00
112.00
113.00
114.00
115.00
116.00
117.00
118.00
119.00
Cross
Ref. #
9211 - 41 Avenue NW
780.438.6055
www.hitechseals.com
O-Ring Design Guide
Metric O-Ring Sizes
Part
Number
50120
50121
50122
50123
50124
50125
50126
50127
50128
50129
50130
50131
50132
50133
50134
50135
50136
50137
50138
50139
50140
50141
50142
50143
50144
50145
50146
50147
50148
50149
50150
50151
50152
50153
50154
50155
50156
50157
50158
50159
50160
50161
50162
50163
50164
50165
50166
50167
50168
50169
50170
C/S
(mm)
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
I.D.
(mm)
120.00
121.00
122.00
123.00
124.00
125.00
126.00
127.00
128.00
129.00
130.00
131.00
132.00
133.00
134.00
135.00
136.00
137.00
138.00
139.00
140.00
141.00
142.00
143.00
144.00
145.00
146.00
147.00
148.00
149.00
150.00
151.00
152.00
153.00
154.00
155.00
156.00
157.00
158.00
159.00
160.00
161.00
162.00
163.00
164.00
165.00
166.00
167.00
168.00
169.00
170.00
Cross
Ref. #
Part
Number
50171
50172
50173
50174
50175
50176
50177
50178
50179
50180
50181
50182
50183
50184
50185
50186
50187
50188
50189
50190
50191
50192
50193
50194
50195
50196
50197
50198
50199
50200
50201
50202
50203
50204
50205
50206
50207
50208
50209
50210
50211
50212
50213
50214
50215
50216
50217
50218
50219
50220
50221
C/S
(mm)
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
I.D.
(mm)
171.00
172.00
173.00
174.00
175.00
176.00
177.00
178.00
179.00
180.00
181.00
182.00
183.00
184.00
185.00
186.00
187.00
188.00
189.00
190.00
191.00
192.00
193.00
194.00
195.00
196.00
197.00
198.00
199.00
200.00
201.00
202.00
203.00
204.00
205.00
206.00
207.00
208.00
209.00
210.00
211.00
212.00
213.00
214.00
215.00
216.00
217.00
218.00
219.00
220.00
221.00
Cross
Ref. #
Part
Number
50222
50223
50224
50225
50226
50227
50228
50229
50230
50231
50232
50233
50234
50235
50236
50237
50238
50239
50240
50241
50242
50243
50244
50245
50246
50247
50248
50249
50250
53040
530412
530414
530425
530437
53045
530462
530475
530487
53050
530515
53053
530544
530545
53056
53058
53060
530615
53063
53065
53067
53069
C/S
(mm)
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
I.D.
(mm)
222.00
223.00
224.00
225.00
226.00
227.00
228.00
229.00
230.00
231.00
232.00
233.00
234.00
235.00
236.00
237.00
238.00
239.00
240.00
241.00
242.00
243.00
244.00
245.00
246.00
247.00
248.00
249.00
250.00
40.00
41.20
41.40
42.50
43.70
45.00
46.20
47.50
48.70
50.00
51.50
53.00
54.40
54.50
56.00
58.00
60.00
61.50
63.00
65.00
67.00
69.00
Cross
Ref. #
www.hitechseals.com
9211 - 41 Avenue NW
780.438.6055
37
O-Ring Design Guide
Metric O-Ring Sizes
Part
Number
53071
53073
53075
530775
53080
530825
53085
530875
53090
530925
53095
530975
53100
53103
53106
53109
53112
53115
53118
53122
53125
53128
53132
53136
53140
53145
53150
53155
53160
53165
53170
53175
53180
53185
53190
53195
53200
-309
-310
-311
-312
-313
-314
-315
-316
-317
-318
-319
-320
-321
-322
38
C/S
(mm)
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.30
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
I.D.
(mm)
71.00
73.00
75.00
77.50
80.00
82.50
85.00
87.50
90.00
92.50
95.00
97.50
100.00
103.00
106.00
109.00
112.00
115.00
118.00
122.00
125.00
128.00
132.00
136.00
140.00
145.00
150.00
155.00
160.00
165.00
170.00
175.00
180.00
185.00
190.00
195.00
200.00
10.46
12.07
13.64
15.24
16.81
18.42
19.99
21.59
23.16
24.77
26.34
27.94
29.51
31.12
Cross
Ref. #
-309
-310
-311
-312
-313
-314
-315
-316
-317
-318
-319
-320
-321
-322
Part
Number
-323
-324
-325
-326
-327
-328
-329
-330
-331
-332
-333
-334
-335
-336
-337
-338
-339
-340
-341
-342
-343
-344
-345
-346
-347
-348
-349
-350
-351
-352
-353
-354
-355
-356
-357
-358
-359
-360
-361
-362
-363
-364
-365
-366
-367
-368
-369
-370
-371
-372
-373
C/S
(mm)
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
I.D.
(mm)
32.69
34.29
37.47
40.64
43.82
46.99
50.17
53.34
56.52
59.69
62.87
66.04
69.22
72.39
75.57
78.74
81.92
85.09
88.27
91.44
94.62
97.79
100.97
104.14
107.32
110.49
113.67
116.84
120.02
123.19
126.37
129.54
132.72
135.89
139.07
142.24
145.42
148.59
151.77
158.12
164.47
170.82
177.17
183.52
189.87
196.22
202.57
208.92
215.27
221.62
227.97
Cross
Ref. #
-323
-324
-325
-326
-327
-328
-329
-330
-331
-332
-333
-334
-335
-336
-337
-338
-339
-340
-341
-342
-343
-344
-345
-346
-347
-348
-349
-350
-351
-352
-353
-354
-355
-356
-357
-358
-359
-360
-361
-362
-363
-364
-365
-366
-367
-368
-369
-370
-371
-372
-373
Part
Number
-374
-375
-376
-377
-378
-379
-380
-381
-382
-383
-384
-385
-386
-387
-388
-389
-390
-391
-392
-393
-394
-395
570242
570352
570362
570372
570392
570412
570442
570443
570452
570453
570472
570476
570492
570493
570496
570512
570516
570522
570523
570525
570526
570530
570542
570543
570546
570552
570553
570556
570572
C/S
(mm)
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.33
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
I.D.
(mm)
234.32
240.67
2 47.02
253.37
266.07
278.77
291.47
304.17
329.57
354.97
380.37
405.26
430.66
456.06
481.38
506.78
532.18
557.58
582.68
608.08
633.48
658.88
24.20
35.20
36.20
37.20
39.20
41.20
44.20
44.30
45.20
45.30
47.20
47.60
49.20
49.30
49.60
51.20
51.60
52.20
52.30
52.50
52.60
53.00
54.20
54.30
54.60
55.20
55.30
55.60
57.20
Cross
Ref. #
-374
-375
-376
-377
-378
-379
-380
-381
-382
-383
-384
-385
-386
-387
-388
-389
-390
-391
-392
-393
-394
-395
P 48A
P 50A
P 52
P 53
P 55
P 56
9211 - 41 Avenue NW
780.438.6055
www.hitechseals.com
O-Ring Design Guide
Metric O-Ring Sizes
Part
Number
570576
570592
570593
570596
570597
570612
570616
57062
570622
570623
570626
57064
570642
570643
570646
570666
570672
57069
570692
570693
570696
570702
570706
570712
570722
570723
57074
570742
570743
570746
570772
57079
570792
570793
570796
570812
570822
570842
570846
570872
570891
570892
570893
570896
570922
570942
570946
570966
570992
570996
571016
C/S
(mm)
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
I.D.
(mm)
57.60
59.20
59.30
59.60
59.70
61.20
61.60
62.00
62.20
62.30
62.60
64.00
64.20
64.30
64.60
66.60
67.20
69.00
69.20
69.30
69.60
70.20
70.60
71.20
72.20
72.30
74.00
74.20
74.30
74.60
77.20
79.00
79.20
79.30
79.60
81.20
82.20
84.20
84.60
87.20
89.10
89.20
89.30
89.60
92.20
94.20
94.60
96.60
99.20
99.60
101.60
Cross
Ref. #
P 58
P 60
P 62
P 63
P 65
P 67
P 70
P 71
P 75
P 80
P 85
P 90
P 95
P 100
P 102
Part
Number
571046
571092
571093
571096
571116
571142
571143
571146
571192
571196
571246
571292
571296
571316
571342
571346
571392
571393
571396
571442
571446
571492
571493
571496
571543
571593
571642
571643
571693
571742
571743
571793
571843
571892
571893
571942
571943
571992
571993
572042
572092
572093
572193
572293
572343
572393
572493
572593
572693
572793
572893
C/S
(mm)
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
5.70
I.D.
(mm)
104.60
109.20
109.30
109.60
111.60
114.20
114.30
114.60
119.20
119.60
124.60
129.20
129.60
131.60
134.20
134.60
139.20
139.30
139.60
144.20
144.60
149.20
149.30
149.60
154.30
159.30
164.20
164.30
169.30
174.20
174.30
179.30
184.30
189.20
189.30
194.20
194.30
199.20
199.30
204.20
209.20
209.30
219.30
229.30
234.30
239.30
249.30
259.30
269.30
279.30
289.30
Cross
Ref. #
P 105
P 110
P 112
P 115
P 120
P 125
P 130
P 132
P 135
P 140
P 145
G 150
P 150
G 155
G 160
G 165
G 170
G 175
G 180
G 185
G 190
G 195
G 200
G 210
G 220
G 230
G 240
G 250
G 260
G 270
G 280
G 290
Part
Number
572993
573193
573393
573493
573593
573793
573993
60012
60018
60020
60023
60024
60025
60026
60032
60034
60035
60036
60037
60038
60040
60041
60042
60044
60045
60046
60048
60050
60052
60056
60058
60059
60060
60062
60064
60065
60067
60069
60070
60072
60073
60074
60075
60076
60079
60080
60085
60086
60088
60090
60092
C/S
(mm)
5.70
5.70
5.70
5.70
5.70
5.70
5.70
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
I.D.
(mm)
299.30
319.30
339.30
349.30
359.30
379.30
399.30
12.00
18.00
20.00
23.00
24.00
25.00
26.00
32.00
34.00
35.00
36.00
37.00
38.00
40.00
41.00
42.00
44.00
45.00
46.00
48.00
50.00
52.00
56.00
58.00
59.00
60.00
62.00
64.00
65.00
67.00
69.00
70.00
72.00
73.00
74.00
75.00
76.00
79.00
80.00
85.00
86.00
88.00
90.00
92.00
Cross
Ref. #
G 300
www.hitechseals.com
9211 - 41 Avenue NW
780.438.6055
39
O-Ring Design Guide
Metric O-Ring Sizes
Part
Number
60095
60098
60100
60103
60105
60110
60112
60114
60115
60118
60120
60122
60124
60125
60128
60130
60134
60135
60138
60140
60142
60145
60146
60148
60150
60160
60165
60166
60169
60170
60172
60175
60180
60185
60190
60195
60200
60208
60210
60215
60220
602225
60230
60242
60250
60262
60266
60270
60272
60290
60295
40
C/S
(mm)
I.D.
(mm)
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
95.00
98.00
100.00
103.00
105.00
110.00
112.00
114.00
115.00
118.00
120.00
122.00
124.00
125.00
128.00
130.00
134.00
135.00
138.00
140.00
142.00
145.00
146.00
148.00
150.00
160.00
165.00
166.00
169.00
170.00
172.00
175.00
180.00
185.00
190.00
195.00
200.00
208.00
210.00
215.00
220.00
222.50
230.00
242.00
250.00
262.00
266.00
270.00
272.00
290.00
295.00
Cross
Ref. #
V 225
V 275
Part
Number
60300
60320
603215
60330
60355
60365
60370
60376
603765
60380
60385
60392
60394
604255
60429
60445
60478
60480
60500
60504
60525
60575
-425
-426
-427
-428
-429
-430
-431
-432
-433
-434
-435
-436
-437
-438
-439
-440
-441
-442
-443
-444
-445
-446
-447
-448
-449
-450
-451
-452
-453
C/S
(mm)
I.D.
(mm)
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
300.00
320.00
321.50
330.00
355.00
365.00
370.00
376.00
376.50
380.00
385.00
392.00
394.00
425.50
429.00
445.00
478.00
480.00
500.00
504.00
525.00
575.00
113.67
116.84
120.02
123.19
126.37
129.54
132.72
135.89
139.07
142.24
145.42
148.59
151.77
158.12
164.47
170.82
177.17
183.52
189.87
196.22
202.57
215.27
227.97
240.67
253.37
266.07
278.77
291.47
304.17
Cross
Ref. #
V 325
V 380
V 430
-425
-426
-427
-428
-429
-430
-431
-432
-433
-434
-435
-436
-437
-438
-439
-440
-441
-442
-443
-444
-445
-446
-447
-448
-449
-450
-451
-452
-453
Part
Number
-454
-455
-456
-457
-458
-459
-460
-461
-462
-463
-464
-465
-466
-467
-468
-469
-470
-471
-472
-473
-474
-475
70011
70015
70023
70034
70035
70040
70058
70059
70060
70068
70079
70083
70094
70096
70106
70107
70110
70111
701147
70115
70120
70128
70150
701595
70160
701667
701746
70181
701873
C/S
(mm)
I.D.
(mm)
Cross
Ref. #
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
316.87
329.57
342.27
354.97
367.67
380.37
393.07
405.26
417.96
430.66
443.36
456.06
468.76
481.46
494.16
506.86
532.26
557.66
582.68
608.08
633.48
658.88
11.00
15.00
23.00
34.00
35.00
40.00
58.00
59.00
60.00
68.00
79.00
83.00
94.00
96.00
106.00
107.00
110.00
111.00
114.70
115.00
120.00
128.00
150.00
159.50
160.00
166.70
174.60
181.00
187.30
-454
-455
-456
-457
-458
-459
-460
-461
-462
-463
-464
-465
-466
-467
-468
-469
-470
-471
-472
-473
-474
-475
9211 - 41 Avenue NW
780.438.6055
www.hitechseals.com
O-Ring Design Guide
Metric O-Ring Sizes
Part
Number
70200
702089
70212
70215
70217
70220
70230
70234
702343
70235
70236
70240
70247
70250
702597
70266
702851
702978
70300
70310
70325
70329
70338
70348
70388
70400
70416
70430
70431
70437
70448
70515
70540
70558
70625
80016
80025
80033
80050
80054
80055
80060
80065
80067
80070
80075
80090
80092
80110
80112
80125
C/S
(mm)
I.D.
(mm)
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
8.00
8.00
8.00
8.00
8.00
8.00
8.00
8.00
8.00
8.00
8.00
8.00
8.00
8.00
8.00
8.00
200.00
208.90
212.00
215.00
217.00
220.00
230.00
234.00
234.30
235.00
236.00
240.00
247.00
250.00
259.70
266.00
285.10
297.80
300.00
310.00
325.00
329.00
338.00
348.00
388.00
400.00
416.00
430.00
431.00
437.00
448.00
515.00
540.00
558.00
625.00
16.00
25.00
33.00
50.00
54.00
55.00
60.00
65.00
67.00
70.00
75.00
90.00
92.00
110.00
112.00
125.00
Cross
Ref. #
Part
Number
80140
80144
80145
80160
80175
80184
80185
80188
80200
80205
80210
80230
80235
80245
80278
80290
80300
80308
80320
80326
80330
80425
80440
80470
80475
80480
80490
80500
80565
841441
841495
841541
841545
841591
841595
841641
841645
841695
841741
841745
841795
841845
841895
841941
841945
841991
841995
842041
842045
842085
842091
C/S
(mm)
I.D.
(mm)
8.00
8.00
8.00
8.00
8.00
8.00
8.00
8.00
8.00
8.00
8.00
8.00
8.00
8.00
8.00
8.00
8.00
8.00
8.00
8.00
8.00
8.00
8.00
8.00
8.00
8.00
8.00
8.00
8.00
8.40
8.40
8.40
8.40
8.40
8.40
8.40
8.40
8.40
8.40
8.40
8.40
8.40
8.40
8.40
8.40
8.40
8.40
8.40
8.40
8.40
8.40
140.00
144.00
145.00
160.00
175.00
184.00
185.00
188.00
200.00
205.00
210.00
230.00
235.00
245.00
278.00
290.00
300.00
308.00
320.00
326.00
330.00
425.00
440.00
470.00
475.00
480.00
490.00
500.00
565.00
144.10
149.50
154.10
154.50
159.10
159.50
164.10
164.50
169.50
174.10
174.50
179.50
184.50
189.50
194.10
194.50
199.10
199.50
204.10
204.50
208.50
209.10
Cross
Ref. #
Part
Number
C/S
(mm)
I.D.
(mm)
Cross
Ref. #
842095
842145
842191
842195
842245
842295
842345
842391
842395
842445
842495
842545
842595
842645
842695
842745
84319
843345
844191
10X475
10X5245
10X579
10X6335
10X683
10X7325
10X782
10X8365
10X1044
8.40
8.40
8.40
8.40
8.40
8.40
8.40
8.40
8.40
8.40
8.40
8.40
8.40
8.40
8.40
8.40
8.40
8.40
8.40
10.00
10.00
10.00
10.00
10.00
10.00
10.00
10.00
10.00
209.50
214.50
219.10
219.50
224.50
229.50
234.50
239.10
239.50
244.50
249.50
254.50
259.50
264.50
269.50
274.50
319.00
334.50
419.10
475.00
524.50
579.00
633.50
683.00
732.50
782.00
836.50
1044.00
P 210
P 215
P 220
P 225
P 230
P 235
P 240
P 245
P 250
P 255
P 260
P 265
P 270
P 275
V 480
V 530
V 585
V 640
V 690
V 740
V 790
V 845
V 1055
P 150A
P 155
P 160
P 165
P 170
P 175
P 180
P 185
P 190
P 195
P 200
P 205
P 209
www.hitechseals.com
9211 - 41 Avenue NW
780.438.6055
41
O-Ring Design Guide
Extrusion (and/or Nibbling)
Description: The seal develops ragged edges (generally on the low-pressure
side) which appear tattered.
Contributing Factors: Excessive clearances. Excessive pressure. Lowmodulus/hardness elastomer. Excessive gland fill. Irregular clearance gaps.
Sharp gland edges. Improper sizing.
Suggested Solutions: Decrease clearances. Higher-modulus/hardness
elastomer. Proper gland design. Use of polymer backup rings.
Over-Compression
Description: The seal exhibits parallel flat surfaces (corresponding to the
contact areas) and may develop circumferential splits within the flattened
surfaces.
Contributing Factors: Improper design-failure to account for thermal or
chemical volume changes, or excessive compression.
Suggested solutions: Gland design should take into account material
responses to chemical and thermal environments.
Spiral Failure
Description: The seal exhibits cuts or marks which spiral around its
circumference.
Contributing Factors: Difficult or tight installation (static). Slow
reciprocating speed. Low-modulus/hardness elastomer. Irregular O-ring
surface finish (including excessive parting line). Excessive gland width.
Irregular or rough gland surface finish. Inadequate lubrication.
Suggested Solutions: Correct installation procedures. Higher-modulus
elastomers. Internally lubed elastomers. Proper gland design. Gland surface
finish of 8-16 microinch RMS. Possible use of polymer backup rings.
42
9211 - 41 Avenue NW
780.438.6055
www.hitechseals.com
O-Ring Design Guide
Compression Set
Description: The seal exhibits a flat-sided cross-section, the flat side
corresponding to the mating seal surfaces.
Contributing Factors: Excessive compression. Excessive temperature.
Incompletely cured elastomer. Elastomer with high compression set.
Excessive volume swell in chemical.
Suggested Solutions: Low compression set elastomer. Proper gland design
for the specific elastomer. Confirm material compatibility.
Outgassing/Extraction
Description: The failure is often very difficult to detect from examination of
the seal. The seal may exhibit a decrease in cross-sectional size.
Contributing Factors: Improper or improperly cured elastomer. High
vacuum levels. Low hardness/plasticized elastomer.
Suggested Solutions: Avoid plasticized elastomers. Ensure all seals are
properly post-cured to minimize outgassing.
Installation Damage
Description: The seal or parts of the seal may exhibit small cuts, nicks or
gashes.
Contributing Factors: Sharp edges on the glands or components. Improper
sizing of elastomer. Low-modulus/hardness elastomer. Elastomer surface
contamination.
Suggested Solutions: Remove all sharp edges. Proper gland design. Proper
elastomer sizing. Higher-modulus/hardness elastomer.
www.hitechseals.com
9211 - 41 Avenue NW
780.438.6055
43
O-Ring Design Guide
Chemical Degradation
Description: The seal may exhibit many signs of degradation including
blisters, cracking, voids or discoloration. In some cases, the degradation is
observable only by measurement of physical properties.
Contributing Factors: Incompatibility with the chemical and/or thermal
environment
Suggested Solutions: Selection of more chemically resistant elastomer.
Thermal Degradation
Description: The seal may exhibit radial cracks located on the highest
temperature surfaces. In addition, certain elastomers may exhibit signs of
softening-a shiny surface as a result of excessive temperatures.
Contributing Factors: Elastomer thermal properties. Excessive temperature
excursions or cycling.
Suggested Solutions: Selection of an elastomer with improved thermal
stability. Evaluation of the possibility of cooling sealing surfaces.
Explosive Decompression
Description: The seal exhibits blisters, pits or ruptures on its surface.
Absorption of gas at high pressure and the subsequent rapid decrease in
pressure. The absorbed gas blisters and ruptures the elastomer surface as the
pressure is rapidly removed.
Contributing Factors: Rapid pressure changes. Low-modulus hardness
elastomer.
Suggested Solutions: Higher-modulus/hardness elastomer. Slower
decompression (release of pressure).
44
9211 - 41 Avenue NW
780.438.6055
www.hitechseals.com
O-Ring Design Guide
Plasma Degradation
Description: The seal often exhibits discolouration, as well as powdered
residue on the surface and possible erosion of elastomer in the exposed area.
Contributing Factors: Chemical reactivity of the plasma. Ion
bombardment (sputtering). Electron bombardment (heating). Improper
gland design. Incompatible seal material.
Suggested Solutions: Plasma-compatible elastomer and compound.
Minimize exposed area. Examine gland design.
Contamination
Description: The seal exhibits foreign materials on the surface and/or within
the O-ring.
Contributing Factors: Process environment deposition. Reactions or
degradation of the elastomer. Non-semiconductor-grade elastomer.
Suggested Solutions: Specify contamination level including manufacturing
and packaging of the seals.
Abrasion
Description: The seal or parts of the seal exhibit a flat surface parallel to the
direction or motion. Loose particles and scrapes may be found on the seal
surface.
Contributing Factors: Rough sealing surfaces. Excessive temperature.
Process environment containing abrasive particles. Dynamic motion. Poor
elastomer surface finish.
Suggested Solutions: Use recommended gland surface finishes. Consider
internally lubed elastomers. Eliminate abrasive components.
www.hitechseals.com
9211 - 41 Avenue NW
780.438.6055
45
Material Guide
O-Ring Design Guide
Aflas™ (TFE/P) (Asahi Glass Co.)
Viton® Extreme™ (FKM)(E.I. DuPont)
-9°C to + 232°C
+16°F to + 450°F
-20°C to + 204°C
-4°F to + 400°F
•
•
•
•
•
Good high temperature capability
Resistant to strong acids and bases, amines, solvents and hot water
Aflas™ is found in numerous applications in the oilfield industry
Poor low temperature performance and low resilience
•
•
•
Chloroprene (CR) (Neoprene - DuPont™)
-40°C to + 121°C
-40°F to + 250°F
•
•
•
Has exceptional ozone, weather, and good chemical resistance
Good mechanical properties are retained over a wide temperature
range
Exhibits good resistance to refrigerants (R12)
Ethylene Propylene (EPDM, EPR)
-54°C to + 150°C
-65°F to + 302°F
•
•
•
•
Excellent resistance to ozone, hot water, steam and aging
Wide temperature range
Commonly used with brake fluids and refrigerants
Poor resistance to petroleum fluids and mineral oils
Fluorocarbon (FKM, FPM)(Viton® E.I. DuPont)
-26°C to + 204°C
-15°F to + 400°F
•
•
•
•
•
Excellent resistance to higher temperatures, petroleum oils, gasoline
Wide range of chemical resistance
Very good ozone, weather and aging resistance
Poor compatibility with H2S over 2%, amines, acetone, hot water
and steam
Poor low temperature characteristics although some compounds
are suitable to -40°C/-40°F
Fluorosilicone (FVMQ)
-56°C to + 204°C
-69°F to + 400°F
•
•
•
•
Excellent resistance to hydrocarbon fuels, as well as petroleum and
silicone oils
Relatively low tear strength, abrasion resistance and tensile strength
Generally not suited for dynamic applications
Highly Saturated Nitrile (HSN, HNBR)
-40°C to + 160°C
-40°F to + 320°F
•
•
•
•
•
•
•
•
A Nitrile based compound with improved chemical resistance
Wider temperature range than standard Nitrile
High strength material that resists extrusion, abrasion and wear
Water and steam resistance to +149°C/+300°F
H2S resistance up to 10%
Commonly used with petroleum oils and CO2
Do not use w/chlorinated hydrocarbons, polar solvents or strong acids
Low temperature compounds available down to -54°C/-65°F
Hytrel® (TPC- ET)(DuPont™)
-54°C to + 149°C
-65°F to + 300°F
•
•
•
•
46
Viton® Extreme™ is a fluorocarbon compound that exhibits
significantly improved performance over regular Viton®
Two types are available- TBR and ETP
TBR- Totally Base Resistant compound that provides improved
performance over other TFE/Propylene polymers
ETP- provides the excellent thermal resistance of Viton® along with
significantly advanced chemical resistance
A thermoplastic elastomer able to handle high temperatures and hostile
fluids
Has excellent strength and toughness properties
Demonstrates high resilience and flexibility which permits easier
installation than PTFE materials
Not suitable with water and phosphate fluids above +80°C/+176°F
9211 - 41 Avenue NW
780.438.6055
www.hitechseals.com
Material Guide
O-Ring Design Guide
Nitrile (Buna-N)
PEEK (Polyetheretherketone) (Ketron® - Quadrant)
-40°C to + 120°C
-40°F to + 248°F
-70°C to + 260°C
-94°F to + 500°F
•
•
•
•
•
•
•
•
•
Presently the most widely used elastomer in the seal industry
Provides an exceptional balance of good mechanical properties, wear
properties and chemical resistance
Resistant to most mineral oils and greases
Do not use with glycol based brake fluids and strong acids
Low temperature compounds to -54°C
High strength
Able to retain its mechanical properties at high temperatures
Commonly used for anti-extrusion purposes
Do not use with Hydrochloric, Nitric, or Sulphuric acids
PTFE
Perfluoroelastomer (FFKM) (Kalrez® E.I. DuPont)
-15°C to + 250°C
+5°F to + 482°F
•
•
•
•
•
•
•
Has the broadest chemical resistance of any elastomeric material
Combines the sealing integrity of elastomers with chemical
resistance approaching that of PTFE
Not suitable with liquid sodium and potassium, fluorinated
solvents and refrigerants
Compounds available to+325°C/+617°F
Kalrez® 4079- A low compression set 75 durometer compound
with excellent chemical resistance, good mechanical properties and
outstanding hot air aging properties.
Kalrez® Spectrum™ 6380- An 80 durometer compound specifically
developed for chemical processes involving hot, aggressive amines;
in addition it has excellent overall chemical resistance.
Kalrez® Spectrum™ 7090- A 90 durometer compound that is
specifically targeted for use in applications requiring high hardness/
higher modulus properties. This compound has excellent
mechanical properties including compression set resistance and
explosive decompression resistance.
-200°C to + 250°C
-328°F to + 482°F
•
•
•
Has virtually universal chemical resistance
Very low coefficient of friction
Fillers such as bronze, moly, glass and carbon are commonly
added to alter mechanical properties
Silicone (VMQ)
-65°C to + 232°C
-85°F to + 450°F
•
•
•
•
Excellent resistance to oxidation and ozone degradation
Most commonly used in static applications due to its poor
tensile strength and wear resistance
Popular for food and medical applications
Polyurethane (AU, EU)
-54°C to + 105°C
-65°F to + 220°F
•
•
•
•
A thermoplastic elastomer with higher tensile strength,
toughness and wear resistance
A good combination of hardness and elasticity
Good low temperature flexibility
Can be used in high pressure hydraulic systems where parts
are subject to wear
* Material information given is intended to serve as a general
guideline only. Actual testing in the application environment is
always recommended.
www.hitechseals.com
9211 - 41 Avenue NW
780.438.6055
47
9211 - 41 Avenue NW | Edmonton, AB | T6E 6R5
Ph: 780.438.6055 | Fax: 780.434.5866 | Email: [email protected]
Toll Free Ph: 1.800.661.6055 | Toll Free Fax: 1.800.465.5866
www.hitechseals.com
Hi-Tech Seals Branches:
Bay #3, 5940 - 30 St. SE | Calgary, AB | T2C 1X8 | Ph: 403.720.2856 | Fax: 403.279.2662
445 Egesz St. | Winnipeg, MB | R2R 2V5 | Ph: 204.775.7881 | Fax: 204.775.7954
1180 Kerrisdale Blvd; Unit #8 | Newmarket, ON | L3Y 8Z9 | Ph: 905.953.9666 | Fax: 905.953.8739
1450 Rue Nobel, Suite #20 | Boucherville, QC | J4B 5H3 | Ph: 450.655.7325 | Fax: 450.655.7359
105 Gladstell St. | Conroe, TX | United States | 77301 | Ph: 936.206.3124 | Fax: 936.756.0538
Hi-Tech Gasket Branch:
8760 50 Ave NW | Edmonton, AB | T6E 5K8 | Ph: 780.439.4894 | Fax: 780.436.9502
®

O-Ring Design Guide - Hi

Transcription

Similar documents

Wear Strip

DK110-112 - Hi-Tech Seals Inc.

Oil Seals