2015 upfitter schematic - Ram Body Builder`s Guide

2015 upfitter schematic - Ram Body Builder`s Guide

2015 UPFITTER SCHEMATIC
PTO Schematics
Left (Driver) Side Battery
Do not install wiring / terminals of any kind at this location
2015 UPFITTER SCHEMATIC
Right (Passenger) Side Battery
Do not install wiring / terminals of any kind at these locations
2015 UPFITTER SCHEMATIC
3500/4500/5500
CHASSIS CABS
RAM Truck Upfitter Schematic
E
C
A
Note – Aux PDC (auxiliary Power Distribution Center-relay/fuse box)
Underhood
G
B
Note – 2 Upfitter
Connectors (Light and Dark Gray)
L
C
PDC (main Power Distribution Center-relay/fuse box) underhood
F
D
B
H K A
D
J
Note – GND (Frame Rail)
E
Ground Point (50A Total Max Load)
F G
Note – PTO Connector
Wires locatedunderneath
vehicle at TransmissionBell
Housing, Left (Driver) Side
Note – Vehicle Wiring,
Blunt Cut (withHeat
Shrink) Rear of Frame
H
Note – Blunt Cut (with Heat
Shrink) wires underneath the PDC C
J
Note – VSIM Module located
interior of vehicle under dash
K
Note – Aux 5/PTO jumper
connector, alongside left (Drivers Side) fender
inner
A
L
The auxiliary switch function logic (BATTERY or
IGNITION FED, MOMENTARY or LATCHING,
LAST STATE) is programmed using the EVIC
display in the instrument cluster.
Note – Port Upfitters
Connectors, Under
Dash Board near park
brake bracket / Steering Column
Rear CameraConnector
Notes –
Max Combined Fuse "rating" allowed in box is
190A. Fuses can be relocated in box as
necessary.
Max allowable combined total continuous
amperage draw is 133A.
Max fuse "rating" in any one location is 40A.
*The upfitter/customer is responsible for placing the correct
fuse in the correct location depending on the actual load.
*Amperages shown in schematics are for fuses/circuits as
installed for the vehicle as sold and will change as fuses are
reconfigured.
MAX ALLOWABLE
CONTINUOUS AMPERAGE
DRAW PER FUSE RATING
FUSE RATING
MAX
ALLOW ABLE
CONTINUOUS
AMPERAGE
20A
14A
25A
17.5A
40A
28A
Date : 07-NOV-2014
2015 UPFITTER SCHEMATIC
2500/3500
PICKUP
RAM Truck Upfitter Schematic
G
C
H
B
A
M
D
F
A
Note – Aux PDC (auxiliary Power Distribution Center-relay/fuse box)
Underhood
B
Note – 2 Upfitter
Connectors (Light and Dark Gray)
C
PDC (mainPower Distribution Center-relay/fuse box) underhood
D
J
Note – GND (Frame Rail)
F G
Ground Point (50A Total Max Load)
Note – Port Upfitters
Connectors, Under
Dash Board near park
brake bracket / Steering Column
Note – Vehicle Wiring,
Blunt Cut (withHeat
Shrink) Rear of Frame
H
Note – Blunt Cut (withHeat
Shrink) wires underneath thePDC
J
Note – VSIM Module located
interior of vehicle under dash
M
Note – Blunt Cut (with Heat
Shrink) Stop Lamp Signal –
CHMSL Feed
C
A
The auxiliary switch function logic (BATTERY or
IGNITION FED, MOMENTARY or LATCHING,
LAST STATE) is programmed using the EVIC
display in the instrument cluster.
Notes –
Max Combined Fuse "rating" allowed in box is
190A. Fuses can be relocated in box as
necessary.
Max allowable combined total continuous
amperage draw is 133A.
Max fuse "rating" in any one location is 40A.
*The upfitter/customer is responsible for placing the correct
fuse in the correct location depending on the actual load.
*Amperages shown in schematics are for fuses/circuits as
installed for the vehicle as sold and will change as fuses are
reconfigured.
MAX ALLOWABLE
CONTINUOUS AMPERAGE
DRAW PER FUSE RATING
FUSE RATING
MAX
ALLOW ABLE
CONTINUOUS
AMPERAGE
20A
14A
25A
17.5A
40A
28A
Date : 07-NOV-2014
2015 UPFITTER SCHEMATIC
Connector_
Upfitter_3_PTO_Trans
D2624A
Cap & Plugs
(Terminated wires
supplied in Upfitter Kit)
ASSY PDC
D6630E
(Body w/h)
31
E
V937-20T VT/BR
57
ASSY PDC
D6630F
(Body w/h)
F940.AZ-20T PK/YL
Y
A998.T-18T RD
V937-20T VT/BR
8
34
3500/4500/5500 CHASSIS CAB
6.7 Diesel Manual Trans w/PTO
(Sales Codes LBN)
M
F856-20T YL/PK
2
8
K128-20T DB/LG
3
63
I250
K129-20T DB
4
67
K119-20T LB/BK
5
66
V937-20T VT/BR
Diesel PCM
D3838B
90
K810-20T VT/DG
6
2
V937.ZG-20T VT/BR
D
K425.A-20T OR/BR
K425-20T OR/BR
BLACK
Port_Upfitters_1 Jumper (Supplied in Upfitter Kit)
D2433A
S
6
93
Trans I200 Body
K400-20T BR/VT
1
32
F425-18T PK
OR/GY (DO NOTUSE)
D
1
F425-20T PK
7
94
78
K425-20T OR/BR
F425-18T PK
R
K427.ZG-20T OR/LG
24
V937-20T VT/BR
D
F425-18T PK
D
2
F425.P-18T PK
2
3
OR/LG (DO NOT USE)
D
5
Z905.AG-18T BK
Z905-18T (BK/DG)
D
6
G905A
I211
A
SA998ZA
1
A998.T-18T RD
Z
Z907.YA-20TBK
5
Z907.YB-20T BK
X
A998.LC-20T RD
4
Y
SA938A
F940.AZ-20T PK/YL
Upfitter Aux PDC Box
D2620A_Upfitters
SF940AC
A998.ZG-18T RD
A998.LA-20T RD
F940.ZF-20T PK/YL
3
14
F930.AO-18T PK/YL
4
15
F940.ZJ-20T PK/YL
16
F930.AO-18T PK/YL
3
I322
SF940AB
5
Aux 1
A998.ZB-20T RD
A962.ZA-10T RD/YL
F601.ZA-12T PK/WT
1
Dark Gray
Connector_
Upfitter_Aux_1
D2622A_Aux_1_Das
Cap & Plugs
(Terminated wires
supplied in Upfitter Kit)
P821.B-20T BR/VT
47
2
24
1
A963.ZA-10T RD/DB
13
40A
A998.ZD-20T RD
19
17
6
25
A964.ZA-10T RD/VT
F603.ZA-12 PK/LG
Light Gray
P822.B-22T BR/WT
25A
44
Cap & Plugs
(Terminated wires
supplied in Upfitter Kit)
1
20
7
26
41
P819.ZB-20T TN/BR
P823.E-20T BR/GY
R
K427.ZG-20T OR/LG
S
K425.A-20T OR/BR
G911A
Blunt-Cut Circuits
D: Under Dash Board near
Park Brake bracket/Steering
Column
4
3
2
1
F: Rear of frame
I9001A_PTO
(reference Blunt Cut Wires
pages)
K427-20T OR/LG
I221
A500.ZA-12T RD/WT
P819.A-20T TN/BR
A966.ZA-10T RD/PK
50
49
29
27
A967.ZA-10T RD/BR 20A
42
43
F
F606-12T PK/YL (OR) PK/OR
F
3
LIGHT GRAY
Port_Upfitters_2
D2621A_Body_D
Z
31
A500-12T RD/WT
4
F606.ZA-12T PK/OR
20A
F606.B-12T PK/YL
Z
Z911.T-20T BK
7
12
K
48
Run Only
F940.ZA-20T PK/YL
11
10
P823.B-20T BR/GY
3
4
D401.M-22T OR
Aux Switch
Bank
Upper
2 D2321A
3
P819.ZD-20T TN/BR
12
B+
39
F605.ZA-12TPK/TN
2
Z907.ZA-12T BK
P822.E-20T BR/WT
16
F425-18T PK
A998.LC-20T RD
6
A965.ZA-10T RD/DG 25A
28
B
P821.E-20T BR/VT
15
P823.D-20T BR/GY
PTO
X
8
9
PTO Jumper
22
F604.ZA-12TPK/TN
Connector_
Upfitter_Aux_2
D2623A_Aux_2_Das
14
2
Aux 4
A998.ZC-20T RD
P821.F-20T BR/VT
P819.B-20T TN/BR
45
Aux 3
4
P820.E-20T BR/OR
13
12
11
3
P820.F-22T BR/OR
10
A938.C-20T RD
1
F930.AN-20TPK/YL
33
P822.D-20T BR/WT
13
F602.ZA-12T PK/RD
42 F940.AX-20T PK/YL
F930.AQ-18T PK/YL
7
6
40A
Aux 2
A998.ZA-20T RD
2
B
23
F940.AY-20TPK/YL
9 F940.AQ-20T PK/YL
P820.B-22T BR/OR
8
10
SD401B
M
D
Jumper (Supplied in Upfitter Kit to be installed by customer)
Z907.ZB-20TBK
6
G907A
20A
A500.B-12T RD/WT
46
I212
4
2
G425.B-12T VT/YL
3
4
A500.A-12T RD/WT
F606.A-12T PK/OR
G425.A-12T VT/YL
A500-12T RD
IF A "BATTERY FEED B+" IS NEEDED,CUT WIRE HERE
3
F606-12T PK/YL (OR) PK/OR
1
G425-12TVT/YL
5
IF AN "IGNITION FEED B+" IS NEEDED,CUT WIRE HERE
D
Date : 07-NOV-2014
2015 UPFITTER SCHEMATIC
Connector_
Upfitter_3_PTO_Trans
D2624A
Cap & Plugs
(Terminated wires
supplied in Upfitter Kit)
E
31
V937-20T VT/BR
ASSY PDC
D6630E
(Body w/h)
34
V937-20T VT/BR
8
57
AISIN TCM
D3855A
(Body w/h)
25
F940.AZ-20T PK/YL
Y
A998.T-18T RD
ASSY PDC
D6630F
(Body w/h)
3500/4500/5500 CHASSIS CAB
6.7 Diesel Auto Trans w/PTO
(Sales Codes LBN/LBV)
K427.ZH-20T OR/LG
M
P
F856-20T YL/PK
2
8
K128-20T DB/LG
3
63
I250
K129-20T DB
4
67
K119-20T LB/BK
5
66
Diesel PCM
D3838B
90
K810-20T VT/DG
6
V937-20T VT/BR
2
V937.ZG-20T VT/BR
D
K425.A-20T OR/BR
K425-20T OR/BR
BLACK
Port_Upfitters_1 Jumper (Supplied in Upfitter Kit)
D2433A
S
6
93
Trans I200 Body
K400-20T BR/VT
1
32
1
F425-20T PK
F425-18T PK
94
7
OR/GY (DO NOT USE)
D
V937-20T VT/BR
D
2
F425-18T PK
F425.P-18T PK
2
F425-18T PK
D
OR/LG (DO NOT USE)
D
3
5
Z905.AG-18T BK
Z905-18T (BK/DG)
D
6
G905A
I211
A998.T-18T RD
Z
Upfitter Aux PDC Box
A
F940.ZF-20T PK/YL
1
Z907.YA-20TBK
5
Y
F940.AZ-20T PK/YL
X
D2620A_Upfitters
SF940AC
SA998ZA
A998.ZG-18T RD
A998.LC-20T RD
4
A998.LA-20T RD
3 A998.LB-20T RD
3
14
4
15
F940.ZJ-20T PK/YL
9 F940.AQ-20T PK/YL
5
16
F930.AO-18T PK/YL
7
Aux 1
A998.ZB-20T RD
10
8
P820.B-22T BR/OR
40A
F601.ZA-12T PK/WT
Cap & Plugs
(Terminated wires
supplied in Upfitter Kit)
P820.E-20T BR/OR
13
P821.E-20T BR/VT
14
2
A963.ZA-10T RD/DB 40A
24
45
F602.ZA-12T PK/RD
P822.E-20T BR/WT
12
P821.B-20T BR/VT
11
1
15
P823.D-20T BR/GY
P823.E-20T BR/GY
13
16
P819.B-20T TN/BR
P819.ZB-20T TN/BR
8
9
6
D401.M-22T OR
Aux Switch
Bank
Upper
2 D2321A
3
11
10
Z911.T-20T BK
7
G911A
P819.ZD-20T TN/BR
2
12
12
Blunt-Cut Circuits
Aux 3
3
4
P822.B-22T BR/WT
17
19
A964.ZA-10T RD/VT 25A
25
44
F603.ZA-12 PK/LG
6
A998.ZC-20T RD
Light Gray
22
A965.ZA-10T RD/DG
1
7
S
K425.A-20T OR/BR
D: Under Dash Board near
Park Brake bracket/Steering
Column
K
4
3
2
1
F: Rear of frame
I9001A_PTO
(reference Blunt Cut Wires
pages)
P823.B-20T BR/GY
26
25A
K427-20T OR/LG
48
I221
F425-18T PK
PTO
X
A998.LC-20T RD
2
A500.ZA-12T RD/WT
39
28
A966.ZA-10T RD/PK 20A
50
49
3
F606.ZA-12T PK/OR
F940.ZA-20T PK/YL
29
27
42
A967.ZA-10T RD/BR
F606.B-12T PK/YL
Z
F
LIGHT GRAY
Port_Upfitters_2
D2621A
Z
31
F
A500-12T RD/WT
F606-12T PK/YL (OR) PK/OR
3
Run Only
4
4
P819.A-20T TN/BR
41
F605.ZA-12TPK/TN
Z907.ZA-12T BK
K427.ZH-20T OR/LG
PTO Jumper
20
F604.ZA-12TPK/TN
Connector_
Upfitter_Aux_2
D2623A_Aux_2_Das
P
B+
Aux 4
B
P820.F-22T BR/OR
6
P821.F-20T BR/VT
13
A938.C-20T RD
1
F930.AN-20TPK/YL
33
10
47
Aux 2
A998.ZA-20T RD
A998.ZD-20T RD
Cap & Plugs
(Terminated wires
supplied in Upfitter Kit)
42 F940.AX-20T PK/YL
P822.D-20T BR/WT
2
B
F940.AY-20TPK/YL
F930.AQ-18T PK/YL
A962.ZA-10TRD/YL
23
1
Dark Gray
Connector_
Upfitter_Aux_1
D2622A_Aux_1_Das
SD401B
I322
SF940AB
F930.AO-18T PK/YL
SA938A
M
D
Jumper (Supplied in Upfitter Kit to be installed by customer)
Z907.ZB-20TBK
6
20A
G907A
43
20A
A500.B-12T RD/WT
I212
4
4
A500.A-12T RD/WT
46
2
G425.B-12T VT/YL
3
F606.A-12T PK/OR
G425.A-12T VT/YL
A500-12T RD
IF A "BATTERY FEED B+" IS NEEDED,CUT WIRE HERE
3
F606-12T PK/YL (OR) PK/OR
1
G425-12TVT/YL
5
IF AN "IGNITION FEED B+" IS NEEDED,CUT WIRE HERE
D
Date : 07-NOV-2014
2015 UPFITTER SCHEMATIC
Connector_
D2624A
E
Upfitter_3_PTO_Trans
31
Cap & Plugs
(Terminated wires
supplied in Upfitter Kit)
3500/4500/5500 CHASSIS CAB
6.4 Gas Aisin Trans (ONLY)
w/PTO (Sales codes LBN/LBV)
V937-20T VT/BR
V937-20T VT/BR
8
ASSY
PDC
D6630E
(Body w/h)
34
A998.T-18T RD
K128-20T DB/LG
K129-20T DB
4
F940.AZ-20T PK/YL
Y
B7
3
25
AISIN
TCM
D3855A
(Body w/h)
A24
F856-20T YL/PK
2
ASSY
PDC
D6630F
(Body w/h)
A66
K427.ZH-20T OR/LG
M
I250
A62
6.4 Gas PCM
D3838A
D3838B
5
K810-20T VT/DG
V937-20T VT/BR
A63
K425-20T OR/BR
2
6
V937.ZG-20T VT/BR
D
K425.A-20T OR/BR
BLACK
Port_Upfitters_1 Jumper (Supplied in Upfitter Kit)
D2433A
S
A31
6
K400-20T BR/VT
1
F425-18T PK
F425-20T PK
7
P
I200
A67
OR/GY (DO NOT USE)
D
1
V937-20T VT/BR
A64
D
2
F425-18T PK
F425.P-18T PK
2
F425-18T PK
D
OR/LG (DO NOT USE)
D
3
5
Z905.AG-18T BK
Z905-18T (BK/DG)
D
6
G905A
I211
A998.G-18T RD
A998.T-18T RD
Y
1
5
Upfitter Aux PDC Box
D2620A_Upfitters
A
SF940AD
F940.AZ-20T PK/YL
4
F940.AAC-20T PK/YL
SA998A
3 A998.LB-20T RD
3
14
4
15
F940.AAD-18T PK/YL
5
16
F930.AP-18TPK/YL
Aux 1
A998.B-20T RD
10
8
1
23
P820.C-22T BR/OR
40A
Dark Gray
Connector_
Upfitter_Aux_1
D2622A_Aux_1_Das
Cap & Plugs
(Terminated wires
supplied in Upfitter Kit)
1
13
F602.A-12T PK/RD
P820.F-22T BR/OR
P820.E-20T BR/OR
6
13
P821.F-20T BR/VT
14
24
P822.E-20T BR/WT
3
Aux Switch
Bank
Upper
D2321A
11
P823.E-20T BR/GY
16
P819.B-20T TN/BR
P819.ZB-20T TN/BR
Z911.T-20T BK
10
7
G911A
P819.ZD-20T TN/BR
2
45
6 D401.M-22T OR
2
15
13
40A
8
9
P821.E-20T BR/VT
10
P823.D-20T BR/GY
A963.A-10T RD/DB
A938.C-20T RD
1
F930.AN-20TPK/YL
33
12
11
2
42 F940.AX-20T PK/YL
F930.AQ-18T PK/YL
7
P822.D-20T BR/WT
Aux 2
A998.A-20T RD
2
B
P821.C-20T BR/VT
47
F940.AY-20TPK/YL
9 F940.AQ-20T PK/YL
A962.A-10T RD/YL
F601.A-12T PK/WT
SD401B
I322
SF940AB
F930.AP-18TPK/YL
SA938A
M
12
12
Blunt-Cut Circuits
Aux 3
3
A998.C-20T RD
19
17
6
25
4
P822.C-22T BR/WT
A964.A-10T RD/VT
F603.A-12 PK/DG
25A
44
P
K427.ZH-20T OR/LG
S
K425.A-20T OR/BR
B+
Aux 4
D: Under Dash Board near
Park Brake bracket/Steering
Column
4
3
2
1
F: Rear of frame
K
I9001
(reference Blunt Cut Wires
pages)
PTO Jumper
A998.D-20T RD
Light Gray
Connector_
Upfitter_Aux_2
D2623A_Aux_2_Das
Cap & Plugs
(Terminated wires
supplied in Upfitter Kit)
20
7
26
P823.C-20T BR/GY
A965.A-10T RD/DG
F604.A-12T PK/TN
25A
K427-20T OR/LG
48
1
A998.E-20T RD
41
A500.ZA-12T RD/WT
P819.C-20T TN/BR
39
A966.A-10TRD/PK
F605.A-12T PK/VT
50
28
3
4
F940.AAB-20T PK/YL
29
27
42
49
Z
F
LIGHT GRAY
Port_Upfitters_2
D2621A
D
Jumper (Supplied in Upfitter Kit to be installed by customer)
Z907.B-20T BK
A967.A-10T RD/BR
F606.C-12T PK/OR
F
F606-12T PK/YL (OR) PK/OR
3
Z
31
A500-12T RD/WT
4
F606.ZA-12T PK/OR
20A
Run Only
Z907.A-12T BK
I221
F425-18T PK
PTO
2
B
22
6
20A
G907A
43
20A
A500.C-12T RD/WT
46
I212
2
G425.C-12TVT/YL
4
A500.A-12T RD/WT
4
A500-12T RD
F606-12T PK/YL (OR) PK/OR
1
G425.A-12T VT/YL
3
IF A "BATTERY FEED B+" IS NEEDED,CUT WIRE HERE
3
F606.A-12T PK/OR
G425-12TVT/YL
5
IF AN "IGNITION FEED B+" IS NEEDED,CUT WIRE HERE
D
Date :07-NOV-2014
2015 UPFITTER SCHEMATIC
31
ASSY PDC
D6630E
(Body w/h)
34
A998.T-18T RD
3500/4500/5500 CHASSIS CAB
6.7 Diesel Manual Trans non-PTO
ASSY PDC
D6630F
(Body w/h)
F940.AZ-20T PK/YL
Y
M
I211
SA998ZA
1
Z
Z907.YA-20TBK
5 Z907.YB-20T BK
X
A998.LC-20T RD
4
Y
F940.AZ-20T PK/YL
Upfitter Aux PDC Box
D2620A_Upfitters
A
SF940AC
A998.T-18T RD
A998.ZG-18T RD
3
14
F930.AO-18T PK/YL
4
15
F940.ZJ-20T PK/YL
5
16
F930.AO-18T PK/YL
Aux 1
10
3
8
P820.B-22T BR/OR
40A
A962.ZA-10TRD/YL
23
47
F601.ZA-12T PK/WT
1
Dark Gray
Connector_
Upfitter_Aux_1
D2622A_Aux_1_Das
Cap & Plugs
(Terminated wires
supplied in Upfitter Kit)
I322
B
2
24
A963.ZA-10T RD/DB
P820.E-20T BR/OR
13
P821.F-20T BR/VT
P821.E-20T BR/VT
14
P822.E-20T BR/WT
15
P823.D-20T BR/GY
16
40A
P819.ZB-20T TN/BR
P819.B-20T TN/BR
45
9
6
P823.E-20T BR/GY
D401.M-22T OR
Aux Switch
Bank
Upper
2 D2321A
3
11
10
Z911.T-20T BK
7
G911A
P819.ZD-20T TN/BR
2
12
12
Blunt-Cut Circuits
A998.ZD-20T RD
17
6
A964.ZA-10T RD/VT 25A
25
44
Light Gray
22
20
7
26
1
A998.LC-20T RD
P823.B-20T BR/GY
F940.ZA-20T PK/YL
28
A966.ZA-10T RD/PK
50
49
F606.B-12T PK/YL
27
Z
(reference Blunt Cut Wires
pages)
I221
A500-12T RD/WT
F
4
F606.ZA-12T PK/OR
20A
31
F: Rear of frame
K
I9001
A500.ZA-12T RD/WT
F606-12T PK/YL (OR) PK/OR
F
3
LIGHT GRAY
Port_Upfitters_2
D2621A
Z
Run Only
4
1
P819.A-20T TN/BR
39
3
2
P819-20TTN/BK
48
41
F605.ZA-12TPK/TN
2
3
PTO Jumper (Supplied in Upfitter Kit to be
installed by customer if necessary)
Aux 5
X
Z907.ZA-12T BK
4
A965.ZA-10T RD/DG 25A
F604.ZA-12TPK/TN
Connector_
Upfitter_Aux_2
D2623A_Aux_2_Das
Park Brake bracket/Steering
Column
B+
Aux 4
A998.ZC-20T RD
D: Under Dash Board near
P822.B-22T BR/WT
19
F603.ZA-12 PK/LG
B
33
P820.F-22T BR/OR
13
8
Aux 3
3
4
Cap & Plugs
(Terminated wires
supplied in Upfitter Kit)
7
6
P821.B-20T BR/VT
A938.C-20T RD
1
F930.AN-20TPK/YL
12
11
1
2
42 F940.AX-20T PK/YL
F930.AQ-18T PK/YL
P822.D-20T BR/WT
13
F602.ZA-12T PK/RD
F940.AY-20TPK/YL
9 F940.AQ-20T PK/YL
10
Aux 2
A998.ZA-20T RD
SD401B
A998.LA-20T RD
F940.ZF-20T PK/YL
SF940AB
A998.ZB-20T RD
SA938A
M
29
D
Jumper (Supplied in Upfitter Kit to be installed by customer)
Z907.ZB-20TBK
6
A967.ZA-10T RD/BR 20A
42
43
G907A
20A
A500.B-12T RD/WT
46
I212
4
2
G425.B-12T VT/YL
3
4
A500.A-12T RD/WT
F606.A-12T PK/OR
G425.A-12T VT/YL
A500-12T RD
IF A "BATTERY FEED B+" IS NEEDED,CUT WIRE HERE
3
F606-12T PK/YL (OR) PK/OR
1
G425-12TVT/YL
5
IF AN "IGNITION FEED B+" IS NEEDED,CUT WIRE HERE
D
Date : 07-NOV-2014
2015 UPFITTER SCHEMATIC
ASSY PDC
D6630F
(Body w/h)
34
F940.AZ-20T PK/YL
3500/4500/5500 CHASSIS CAB 6.7
Diesel Auto Trans Non - PTO
ASSY PDC
D6630E
(Body w/h)
31
A998.T-18T RD
M
Y
I211
A998.ZG-18T RD
Upfitter Aux PDC Box
D2620A_Upfitters
A
SF940AC
Z
Z907.YA-20TBK
X
A998.LC-20T RD
Y
5
4
3
14
4
15
F940.ZJ-20T PK/YL
3
Aux 1
A998.ZB-20T RD
5
16
F930.AO-18T PK/YL
P820.B-22T BR/OR
10
8
1
23
40A
A962.ZA-10TRD/YL
F601.ZA-12T PK/WT
Dark Gray
Connector_
Upfitter_Aux_1
D2622A_Aux_1_Das
Cap & Plugs
(Terminated wires
supplied in Upfitter Kit)
13
2
A998.ZD-20T RD
33
P820.F-22T BR/OR
P820.E-20T BR/OR
6
13
P821.F-20T BR/VT
P821.E-20T BR/VT
10
14
P822.E-20T BR/WT
24
15
16
P819.B-20T TN/BR
45
8
9
6 D401.M-22T OR
Aux Switch
3
Bank
Upper
2 D2321A
11
P823.E-20T BR/GY
13
P819.ZB-20T TN/BR
Z911.T-20T BK
10
7
P819.ZD-20T TN/BR
2
12
12
Blunt-Cut Circuits
19
17
6
A964.ZA-10T RD/VT 25A
25
44
F603.ZA-12 PK/LG
A998.ZC-20T RD
D: Under Dash Board near
P822.B-22T BR/WT
Park Brake bracket/Steering
Column
B+
Aux 4
4
3
2
1
P823.B-20T BR/GY
22
20
7
A965.ZA-10T RD/DG
26
48
F604.ZA-12TPK/TN
Connector_
Upfitter_Aux_2
D2623A_Aux_2_Das
1
P819-20TTN/BK
41
X
F605.ZA-12TPK/TN
2
A966.ZA-10T RD/PK
28
3
F940.ZA-20T PK/YL
31
F606.B-12T PK/YL
50
Z
A500-12T RD/WT
F606-12T PK/YL (OR) PK/OR
F606.ZA-12T PK/OR
F
3
49
LIGHT GRAY
Port_Upfitters_2
D2621A
Z
42
F
4
20A
29
A967.ZA-10T RD/BR
27
Z907.ZA-12T BK
I221
P819.A-20T TN/BR
Run Only
4
(reference Blunt Cut Wires
pages)
A500.ZA-12T RD/WT
39
Rear of frame
PTO Jumper (Supplied in Upfitter Kit to
be installed by customer if necessary)
AUX 5
A998.LC-20T RD
F:
K
I9001
25A
Light Gray
B
7
P823.D-20T BR/GY
40A
A938.C-20T RD
1
F930.AN-20TPK/YL
Aux 3
3
4
Cap & Plugs
(Terminated wires
supplied in Upfitter Kit)
42 F940.AX-20T PK/YL
F930.AQ-18T PK/YL
P822.D-20T BR/WT
A963.ZA-10T RD/DB
F602.ZA-12T PK/RD
F940.AY-20TPK/YL
9 F940.AQ-20T PK/YL
12
11
1
2
B
P821.B-20T BR/VT
47
Aux 2
A998.ZA-20T RD
SD401B
I322
SF940AB
F930.AO-18T PK/YL
SA938A
M
F940.AZ-20T PK/YL
A998.LB-20T RD
A998.LA-20T RD
F940.ZF-20T PK/YL
SA998ZA
A998.T-18T RD
1
D
Jumper (Supplied in Upfitter Kit to be installed by customer)
Z907.ZB-20TBK
6
20A
G907A
43
20A
A500.B-12T RD/WT
46
I212
4
2
G425.B-12T VT/YL
3
4
A500.A-12T RD/WT
F606.A-12T PK/OR
G425.A-12T VT/YL
A500-12T RD
IF A "BATTERY FEED B+" IS NEEDED,CUT WIRE HERE
3
F606-12T PK/YL (OR) PK/OR
1
G425-12TVT/YL
5
IF AN "IGNITION FEED B+" IS NEEDED,CUT WIRE HERE
D
Date :07-NOV-2014
2015 UPFITTER SCHEMATIC
ASSY PDC
D6630F
(Body w/h)
34
F940.AZ-20T PK/YL
3500/4500/5500 CHASSIS CAB
5.7/6.4 GAS Auto Trans Non - PTO
ASSY PDC
D6630E
(Body w/h)
31
A998.T-18T RD
M
Y
I211
A998.G-18T RD
A998.T-18T RD
Y
1
5
Upfitter Aux PDC Box
D2620A_Upfitters
A
SF940AD
SA998A
3
14
4
15
F940.AAD-18T PK/YL
5
16
F930.AP-18TPK/YL
3
Aux 1
A998.B-20T RD
10
8
1
23
P820.C-22T BR/OR
40A
F601.A-12T PK/WT
Cap & Plugs
(Terminated wires
supplied in Upfitter Kit)
A962.A-10T RD/YL
P821.C-20T BR/VT
47
A998.A-20T RD
A963.A-10TRD/DB
F602.A-12T PK/RD
24
33
P820.F-22T BR/OR
P820.E-20T BR/OR
9
6 D401.M-22T OR
6
13
P821.F-20T BR/VT
P821.E-20T BR/VT
10
14
P822.E-20T BR/WT
15
P823.D-20T BR/GY
16
P823.E-20T BR/GY
Aux Switch
3
Bank
Upper
2 D2321A
11
10
Z911.T-20T BK
7
40A
P819.B-20T TN/BR
45
P819.ZB-20T TN/BR
G911A
P819.ZD-20T TN/BR
2
12
12
Blunt-Cut Circuits
A998.C-20T RD
19
17
6
25
F603.A-12T PK/DG
A964.A-10T RD/VT
Light Gray
22
20
7
26
Park Brake bracket/Steering
Column
25A
44
B+
4
3
2
1
K
P819-20TTN/BK
I221
AUX 5
A998.E-20T RD
A500-12T RD/WT
A500.ZA-12T RD/WT
F
4
P819.C-20T TN/BR
39
41
(reference Blunt Cut Wires
pages)
PTO Jumper (Supplied in Upfitter Kit to be
installed by customer if necessary)
25A
48
F: Rear of frame
I9001A_PTO
P823.C-20T BR/GY
A965.A-10T RD/DG
F604.A-12T PK/TN
Connector_
Upfitter_Aux_2
D2623A_Aux_2_Das
D: Under Dash Board near
P822.C-22T BR/WT
Aux 4
A998.D-20T RD
1
F605.A-12T PK/VT
2
B
8
Aux 3
3
4
Cap & Plugs
(Terminated wires
supplied in Upfitter Kit)
A938.C-20T RD
1
F930.AN-20TPK/YL
7
13
1
2
42 F940.AX-20T PK/YL
F930.AQ-18T PK/YL
12
11
13
F940.AY-20TPK/YL
9 F940.AQ-20T PK/YL
P822.D-20T BR/WT
Aux 2
2
B
SD401B
I322
SF940AB
F930.AP-18TPK/YL
Dark Gray
Connector_
Upfitter_Aux_1
D2622A_Aux_1_Das
SA938A
M
F940.AZ-20T PK/YL
Z907.YB-20TBK
4
F940.AAC-20T PK/YL
A966.A-10TRD/PK
28
3
50
F940.AAB-20T PK/YL
31
LIGHT GRAY
Z907.A-12T BK
Z
42
D
Jumper (Supplied in Upfitter Kit to be installed by customer)
Z907.B-20T BK
A967.A-10T RD/BR
27
Port_Upfitters_2
D2621A
Z
29
F606.C-12T PK/OR
F
3
49
Run Only
4
F606-12T PK/YL (OR) PK/OR
F606.ZA-12T PK/OR
20A
6
20A
G907A
43
20A
A500.C-12T RD/WT
46
I212
4
A500.A-12T RD/WT
4
G425.C-12TVT/YL
3
A500-12T RD
IF A "BATTERY FEED B+" IS NEEDED,CUT WIRE HERE
3
2 F606.A-12T PK/OR
G425.A-12T VT/YL
F606-12T PK/YL (OR) PK/OR
1
G425-12TVT/YL
5
IF AN "IGNITION FEED B+" IS NEEDED,CUT WIRE HERE
D
Date : 07-NOV-2014
2015 UPFITTER SCHEMATIC
34
ASSY PDC
D6630F
(Body w/h)
F940.AZ-20T PK/YL
31
2500/3500 PICKUP
6.7 Diesel with Auxiliary Switches
(Sales Code LHL)
ASSY PDC
D6630E
(Body w/h)
A998.T-18T RD
M
Y
I211
A998.G-18T RD
A998.T-18T RD
1
Y
5
Upfitter Aux PDC Box
D2620A_Upfitters
A
SF940AD
F940.AZ-20T PK/YL
4
F940-20T PK/YL
SA998A
F930-18T PK/YL
Aux 1
A998-20T RD
10
3
14
4
15
F940-18T PK/YL
5
16
F930-18T PK/YL
Cap & Plugs
(Terminated wires
supplied in Upfitter Kit)
23
1
A998.A-20T RD
1
13
47
A963-10T RD/DB
24
13
P821.E-20T BR/VT
14
P822.E-20T BR/WT
15
P823.D-20T BR/GY
16
P819.YC-20T TN/BR
45
8
9
6 D401.M-22T OR
P823.E-20T BR/GY
Aux Switch
Bank
Upper
2 D2321A
3
11
10
Z911.T-20T BK
7
G911A
P819.ZD-20T TN/BR
2
12
12
Blunt-Cut Circuits
Aux 3
3
4
19
17
6
25
A964-10T RD/VT
F603-12 PK/DG
A998-20T RD
Park Brake bracket/Steering
Column
25A
44
Light Gray
7
26
25A
48
I221
AUX 5
A998-20T RD
1
41
2
A966-10T RD/PK
50
3
F606.ZA-12T PK/OR
20A
F940-20T PK/YL
49
29
27
42
Z
D
Jumper (Supplied in Upfitter Kit to be installed by customer)
Z907-20T BK
A967-10T RD/BR
F606-12T PK/OR
F
LIGHT GRAY
Port_Upfitters_2
D2621A
Z
31
F606-12T PK/YL (OR) PK/OR
3
Run Only
4
F
4
P819-20T TN/BR
39
28
A500-12T RD/WT
A500.ZA-12T RD/WT
F605-12T PK/VT
Z907.ZA-12T BK
(reference Blunt Cut Wires
pages)
P823-20T BR/GY
A965-10T RD/DG
F604-12T PK/TN
Connector_
Upfitter_Aux_2
D2623A_Aux_2_Das
F: Rear of frame
B+
20
22
D: Under Dash Board near
P822-22T BR/WT
Aux 4
B
P820.E-20T BR/OR
13
P821.F-20T BR/VT
P822.D-20T BR/WT
40A
A938.C-20T RD
1
F930.AN-20TPK/YL
33
12
F602-12TPK/RD
A998.D-20T RD
Cap & Plugs
(Terminated wires
supplied in Upfitter Kit)
42 F940.AX-20T PK/YL
F930.AQ-18T PK/YL
10
11
2
F940.AY-20TPK/YL
P820.F-22T BR/OR
P821-20T BR/VT
Aux 2
2
B
A962-10T RD/YL
SD401B
I322
SF940AB
6
40A
Dark Gray
Connector_
Upfitter_Aux_1
D2622A_Aux_1_Das
7
P820-22T BR/OR
8
F601-12T PK/WT
9 F940.AQ-20T PK/YL
SA938A
M
3 A998.LB 20T RD
6
20A
G907A
43
20A
A500-12T RD/WT
46
I212
2
G425-12TVT/YL
4
A500.A-12T RD/WT
4
A500-12T RD
F606.A-12T PK/OR
1
F606-12T PK/YL (OR) PK/OR
G425-12TVT/YL
G425.A-12T VT/YL
3
IF A "BATTERY FEED B+" IS NEEDED,CUT WIRE HERE
3
5
IF AN "IGNITION FEED B+" IS NEEDED,CUT WIRE HERE
D
Date : 07-NOV-2014
2015 UPFITTER SCHEMATIC
34
ASSY PDC
D6630F
(Body w/h)
F940.AZ-20T PK/YL
31
A998.T-18T RD
M
2500/3500 PICKUP
5.7/6.4 Gas with Auxiliary Switches
(Sales Code LHL)
ASSY PDC
D6630E
(Body w/h)
Y
I211
A998.ZG-18T RD
Upfitter Aux PDC Box
D2620A_Upfitters
A
SF940AC
SA998ZA
Z
Z907.YA-20TBK
X
A998.LC-20T RD
F940.ZF-20T PK/YL
F930.AO-18T PK/YL
Aux 1
A998.ZB-20T RD
A998.LA-20T RD
3
14
4
15
5
16
F940.ZJ-20T PK/YL
F930.AO-18T PK/YL
P820.B-22T BR/OR
10
8
1
23
40A
A962.ZA-10TRD/YL
F601.ZA-12T PK/WT
Dark Gray
Connector_
Upfitter_Aux_1
D2622A_Aux_1_Das
Cap & Plugs
(Terminated wires
supplied in Upfitter Kit)
11
2
A963.ZA-10T RD/DB 40A
24
45
F602.ZA-12T PK/RD
19
17
6
25
F603.ZA-12 PK/LG
7
SD401B
I322
SF940AB
F940.AY-20TPK/YL
A938.C-20T RD
42 F940.AX-20T PK/YL
1
8
9
6 D401.M-22T OR
F930.AN-20TPK/YL
F930.AQ-18T PK/YL
33
P820.F-22T BR/OR
Aux Switch
Bank
Upper
2 D2321A
P820.E-20T BR/OR
6
3
13
P821.F-20T BR/VT
P821.E-20T BR/VT
10
13
14
P822.E-20T BR/WT
11
15
P823.D-20T BR/GY
16
P819.YC-20T TN/BR
P823.E-20T BR/GY
10
Z911.T-20T BK
7
G911A
P819.ZD-20T TN/BR
2
A964.ZA-10T RD/VT
12
12
Light Gray
22
20
7
26
P822.B-22T BR/WT
Park Brake bracket/Steering
Column
1
B+
(reference Blunt Cut Wires
pages)
P823.B-20T BR/GY
48
I221
AUX 5
X
41
2
3
A966.ZA-10T RD/PK 20A
50
49
29
27
A967.ZA-10T RD/BR 20A
42
43
F606.B-12T PK/YL
F
3
LIGHT GRAY
Port_Upfitters_2
D2621A
Z
31
F606-12T PK/YL (OR) PK/OR
F606.ZA-12T PK/OR
Run Only
F940.ZA-20T PK/YL
Z
F
4
P819.A-20T TN/BR
39
28
4
A500-12T RD/WT
A500.ZA-12T RD/WT
A998.LC-20T RD
F605.ZA-12TPK/TN
Z907.ZA-12T BK
F: Rear of frame
A965.ZA-10T RD/DG 25A
F604.ZA-12TPK/TN
Connector_
Upfitter_Aux_2
D2623A_Aux_2_Das
D: Under Dash Board near
25A
44
Aux 4
A998.ZC-20T RD
B
3 A998.LB 20T RD
9 F940.AQ-20T PK/YL
SA938A
M
Blunt-Cut Circuits
A998.ZD-20T RD
(Terminated wires
supplied in Upfitter Kit)
F940.AZ-20T PK/YL
4
Aux 3
3
4
Cap & Plugs
Y
5
12
13
1
A998.T-18T RD
P822.D-20T BR/WT
Aux 2
A998.ZA-20T RD
2
B
P821.B-20T BR/VT
47
1
D
Jumper (Supplied in Upfitter Kit to be installed by customer)
Z907.ZB-20TBK
6
G907A
20A
A500.B-12T RD/WT
I212
4
4
A500.A-12T RD/WT
46
2
G425.B-12T VT/YL
F606.A-12T PK/OR
A500-12T RD
1
F606-12T PK/YL (OR) PK/OR
G425-12TVT/YL
G425.A-12T VT/YL
3
IF A "BATTERY FEED B+" IS NEEDED,CUT WIRE HERE
3
5
IF AN "IGNITION FEED B+" IS NEEDED,CUT WIRE HERE
D
Date : 07-NOV-2014
2015 UPFITTER SCHEMATIC
Blunt Cut Wires
3500/4500/5500 CHASSIS CAB
“G” Blunt Cut wires located at Right (Passenger side) Rear of Frame
A100-14T RD/VT (Trailer Tow Battery feed)
G #
B40-14T DG (Electric Brake feed)
G #
L76-16T WT/BR (Trailer Tow Running/Park Lamps feed)
G #
L111-16T WT/OR (Trailer Tow Back-up Lamps feed)
G#
L614-18T LG (Trailer Tow Stop/Turn Right)
G#
L615-18T YL (Trailer Tow Stop/Turn Left)
Z914-12T BK/GY
G#
(Ground)
G#
# The maximum alowable continous amperage for these Trailer
Tow circuits will be found under "ELECTRICAL/WIRING
INFORMATION", "ELECTRICAL POWER USAGE", "AMPERAGE
CAPACITY PER CIRCUIT".
“H” Blunt Cut wires located underneath PDC
*H
L177-18T WT/BR
C
(PARK LAMP RELAY- LSD)
H
L312-18T BK/VT
*H
L313-18T BK/LG
(LOW BEAM RELAY- LSD)
H
L314-18T BK/TN
(DO NOT USE)
*H
H
*H
*H
H
*H
H
H
(SNOW PLOW LIGHTING ENABLE- B+)
L315-18T BK/LB (HIGH BEAM RELAY- LSD)
L316-18T BK/OR
(DO NOT USE)
L317-18T WT/VT
(TURN SIGNAL RELAY,LEFT- HSD)
** These two circuits become active when the 6 cavity Light Gray connector
(Jumper port Upfitter 2) included in the upfitter kit is installed onto the Light
Gray connector at locaiton 'D' in the vehicle diagram
L318-18T VT/BR (TURN SIGNAL RELAY,RIGHT- HSD)
T754-22T DG/GY (HARD-WIRED REMOTE START/STOP)
VEHICLE WIRING
** A500-12T RD/WT
(Battery feed)
T120-20T DG/OR (TRANS PARK POSITION DETECTION)
** F606-12T PK/OR (Ignition Run feed)
L950-20T LG/WT (REAR BULB OUTAGE DETECTION DISABLE)
L56-18T WT/VT
L779-18T WT/LB (SEPARATE REAR STOP / TURN LAMPS)
F
(Stop Lamp signal / CHMSL feed)
V937-20T VT/BR (Speed Control Switch return)
F
D
F425-18T PK
* The maximum allowable continuous amperage for these Snow
Plow and T120 circuits will be found under "ELECTRICAL/WIRING
INFORMATION", "ELECTRICAL POWER USAGE", "AMPERAGE
CAPACITY PER CIRCUIT".
F
(PTO switch)
Z905-18T BK/DG
(Ground)
G425-12T VT/YL (Power takeoff status bulb)
D
D
“F” Blunt Cut wires located at Left(Drivers Side) Rear
of Frame
D
“D” Blunt Cut wires are part of the Upfitter Ports 1 & 2
Jumpers located under Dash near Park Brake Bracket/Streering
Column. Connectors (Black & Gray) for these circuits are part of
the Upfitter Jumper kit.
Date : 07-NOV-2014
2015 UPFITTER SCHEMATIC
Blunt Cut Wires
2500/3500 Pickup Box-off (Sales Code XBC)
“G” Blunt Cut wires located at Right (Passenger Side) Rear of Frame
A100-14T RD/VT (Trailer Tow Battery feed)
G #
B40-14T DG (Electric Brake feed)
L76-16T WT/BR (Trailer Tow Running/Park Lamps feed)
L111-16T WT/OR (Trailer Tow Back-up Lamps feed)
L614-18T LG (Trailer Tow Stop/Turn Right)
G#
G #
G #
G#
L615-18T YL (Trailer Tow Stop/Turn Left)
Z914-12T BK/GY
G #
(Ground)
G#
# The maximum alowable continous amperage for these Trailer
Tow circuits will be found under "ELECTRICAL/WIRING
INFORMATION", "ELECTRICAL POWER USAGE", "AMPERAGE
CAPACITY PER CIRCUIT".
“H” Blunt Cut wires located underneath PDC
*H
L177-18T WT/BR
C
(PARK LAMP RELAY- LSD)
H
L312-18T BK/VT
(SNOW PLOW LIGHTING ENABLE- B+)
* H
L313-18T BK/LG
(LOW BEAM RELAY- LSD)
H
L314-18T BK/TN
(DO NOT USE)
*H
L315-18T BK/LB (HIGH BEAM RELAY- LSD)
H
L316-18T BK/OR
(DO NOT USE)
*H
L317-18T WT/VT
(TURN SIGNAL RELAY,LEFT- HSD)
* H
H
* H
H
H
L318-18T VT/BR (TURN SIGNAL RELAY,RIGHT- HSD)
T754-22T DG/GY
(DO NOT USE)
“M” Blunt Cut wire located at Left (Drivers Side) Rear of Frame
M
L56-18T WT/VT
(Stop Lamp signal / CHMSL feed)
VEHICLE WIRING
T120-20T DG/OR (TRANS PARK POSITION DETECTION)
L950-20T LG/WT (REAR BULB OUTAGE DETECTION DISABLE)
L779-18T WT/LB
(DO NOT USE)
* The maximum allowable continuous amperage for these Snow
Plow and T120 circuits will be found under
"ELECTRICAL/WIRING INFORMATION", "ELECTRICAL
POWER USAGE", "AMPERAGE CAPACITY PER CIRCUIT".
G425-12T VT/YL (Spare Circuit - Pass Thru)
D
“D” Blunt Cut wires are part of the Upfitter Ports 1 & 2
Jumpers located under Dash near Park Brake Bracket/Streering
Column. The Connector (Gray) for this circuit is part of
the Upfitter Jumper kit.
Date : 07-NOV-2014
2015 UPFITTER SCHEMATIC
Blunt Cut Wires
2500/3500 PICKUP Box-on
W/Auxiliary Switches (Sales Code LHL)
“H” Blunt Cut wires located underneath PDC
* H
C
L177-18T WT/BR (PARK LAMP RELAY- LSD)
H
L312-18T BK/VT
* H
L313-18T BK/LG
(LOW BEAM RELAY- LSD)
H
L314-18T BK/TN
(DO NOT USE)
* H
L315-18T BK/LB
(HIGH BEAM RELAY- LSD)
(SNOW PLOW LIGHTING ENABLE- B+)
H
L316-18T BK/OR
(DO NOT USE)
* H
L317-18T WT/VT
(TURN SIGNAL RELAY,LEFT- HSD)
* H
L318-18T VT/BR
(TURN SIGNAL RELAY,RIGHT- HSD)
H
* H
T754-22T DG/GY
(DO NOT USE)
“M” Blunt Cut wire located at Left (Drivers Side) Rear of Frame
M
L56-18T WT/VT (Stop Lamp signal / CHMSL feed)
VEHICLE WIRING
T120-20T DG/OR (TRANS PARK POSITION DETECTION)
H
L950-20T LG/WT
(REAR BULB OUTAGE DETECTION DISABLE)
H
L779-18T WT/LB
(DO NOT USE)
* The maximum allowable continuous amperage for these Snow Plow
and T120 circuits will be found under "ELECTRICAL/WIRING
INFORMATION", "ELECTRICAL POWER USAGE", "AMPERAGE
CAPACITY PER CIRCUIT".
G425-12T VT/YL (Spare Circuit - Pass Thru)
D
“D” Blunt Cut wires are part of the Upfitter Ports 1 & 2
Jumpers located under Dash near Park Brake Bracket/Streering
Column. The Connector (Gray) for this circuit is part of
the Upfitter Jumper kit.
Date : 07-NOV-2014
2015 UPFITTER SCHEMATIC
Blunt Cut Wires
2500/3500 PICKUP Box-on
W/O Auxiliary Switches
“H” Blunt Cut wires located underneath PDC
*
*
*
*
*
*
*
*
H
L177-18T WT/BR
C
(PARK LAMP RELAY-LSD)
H
L312-18T BK/VT
(SNOW PLOW LIGHTING ENABLE- B+)
H
L313-18T BK/LG
(LOW BEAM RELAY- LSD)
L314-18T BK/TN
(DO NOT USE)
L315-18T BK/LB
(HIGH BEAM RELAY- LSD)
H
H
H
H
H
L316-18T BK/OR
(DO NOT USE)
L317-18T WT/VT
(TURN SIGNAL RELAY,LEFT- HSD)
L318-18T VT/BR
(TURN SIGNAL RELAY,RIGHT- HSD)
“M” Blunt Cut wire located at Left (Drivers Side) Rear of Frame
M
L56-18T WT/VT
(Stop Lamp signal / CHMSL feed)
VEHICLE WIRING
SNOW PLOW CIRCUITS ARE NOT AVAILABLE ON
* THESE
POWER WAGON WITH "TRU-LOK" AXLES
The maximum allowable continuous amperage for these
Snow Plow circuits will be found under
"ELECTRICAL/WIRING INFORMATION", "ELECTRICAL
POWER USAGE", "AMPERAGE CAPACITY PER CIRCUIT".
Date : 07-NOV-2014
2015 UPFITTER SCHEMATIC
Upfitter Jumper HarnessOnly
68049501AB
PTO Connector
Dash – Dark Gray
Connector_Upfitter Aux_1
E
1
2
3
4
5
6
7
8
Dash – Light Gray
Connector_Upfitter_2 Aux_2
*Note – Each Circuit can handlemaximum
continuous current of 28A. Maximum
combined load for AUX Switches is 133A
*The upfitter/customer is responsible for
placing the correct fuse in the correct
location depending on the actual load.
B
B
K400-20T BR/VT (ENG – ACCEL PEDAL POS SNSR RTN 2)
F856-20T YL/PK (ENG – 5V ENGINE SNSR FEED SEC)
1
F601-12T PK/WT (RELAY 1 OUTPUT)
1
K128-20T DB/LG (ENG – REMOTE THROTTLE SWITCH SIGNAL)
K129-20T DB/DG (ENG – REMOTE THROTTLE SWITCH)
F602-12T PK/RD
2
(RELAY 2 OUTPUT)
2
F605-12T PK/YL (RELAY 5 OR PTO RELAY OUTPUT)
K119-20T LG/BK (ENG – MAXIMUM OPERATING SPEED SWITCH)
3
K810-20T VT/DG (ENG – ACCELERATOR INTERLOCK SWITCH)
F425-20T PK (PWR – POWER TAKEOFF SWITCH)
V937-20T VT/BR
4
(SCS – SPEED CTRL SW RTN)
F603-12T PK/DG (RELAY 3 OUTPUT)
3
F604-12T PK/LB (RELAY 4 OUTPUT)
4
Z907-12T AWG BK (GND)
G425-12T AWG VT/YL
(Spare Circuit - Pass Thru)
THESE ARE NORMALLY NOT CUSTOMER REPLACED
Jumper
PTO
Dark Gray
D
D
OR/GY (DO NOT USE)
K
Light Gray
Black
1
Jumper
NON-PTO
(Aux 5)
K
Jumper
Port_Upfitters_2
Jumper
Port_Upfitters_1
1
2 V937-20T VT/BR (SCS - SPEED CTRL SW RTN)
2
3 F425-20T PK (PWR - PTO SWITCH)
3
4
4
F606-12T AWG PK/YL (OR) PK/OR
Dark Gray
(PWR - ATM UPFITTER IGN RUN FEED)
1
1 P819 20T TN/BK
A500-12T AWG RD OR RD/WT (PWR - BATT - ATM - UPFITTER FUSED FEED)
2 K427-20T OR/LG
2
5
6
OR/LG (DO NOT USE)
3
5 G425-12T VT/YL (Spare Circuit - Pass Thru)
4
Z905-18T BK/DG (GROUND)
6
F425-18T PK
3
4
Date : 07-NOV-2014
2015 UPFITTER SCHEMATIC
PTO CONNECTOR Underweath Vehicle at Transmission
Circuit Function and Pin - Out
3500/4500/5500 CHASSIS CAB ONLY
Connector_
Upfitter_3_PTO_Trans
D2624A
Cap & Plugs
(Terminated wires
supplied in Upfitter Kit)
8
2
3
Transmission – Dark Gray
Connector_Upfitter_3PTO
4
5
6
1
E
7
SCS - SPEED CTRL SW RTN
V937-20T VT/BR
ENG - 5V ENGINE SNSR FEED SEC
F856-20T YL/PK
ENG - REMOTE THROTTLE SWITCH SIGNAL
K128-20T DB/LG
ENG - REMOTE THROTTLE SWITCH
K129-20T DB
ENG - MAXIMUM OPERATING SPEED SWITCH (Diesel Only) K119-20T LG/BK
ENG - ACCELERATOR INTERLOCK SWITCH
ENG - ACCEL PEDAL POS SNSR RTN 2
PWR - PO WER TAKEOFF SWITCH
Diesel/Gas
PCM
K810-20T VT/DG
K400-20T BR/VT
F425-20T PK
Date : 07-NOV-2014
2015 UPFITTER SCHEMATIC
Bagged Upfitter Kit Detail
68209998AB/68209998AC
*Upfitter Connection Jumper
*8 – 12 GA Circuits for Upfitter Aux Connectors 1 & 2
*8 – 20 GA Circuits for the Transmission PTO Connector
*2 – PTO/Non-PTO Jumper Connectors
(1) Port Upfitter Gray Connector w/5 wires
(1) Port Upfitter Black Connector w/5 wires
The Vehicle has been equipped to ease the installation of a PTO by allowing convenient access to circuits needed without
having to splice into the main harness.
Located left of Main PDC Box and along the left (Drivers Side) fender inner (location K) is a dark gray jumper connector
that allows the vehicle function to switch between PTO and non-PTO operation,although this normally need not be acessed
by the customer.If required,the jumpers are located in this upfitter kit.If necessary,verify proper jumper usage by reviewing jumper
design on previous pages.
In the rear of the vehicle, you can find all required T-TOW circuits, two (2) additional power circuits (1 Battery and 1 Ignition)
and a Stop Lamp / CHMSL Feed Circuit.
In the Engine compartment you will find two (2) (A Light Gray and a Dark Gray) Upfitter AUX connectors (location B) which allow easy
access to the switch bank and fuse box outputs, mating terminated circuits are included in this kit as needed.
Connectors (Black & Gray)for these circuits are part of the Upfitter jumper kit.
The Battery line to the AUX PDC is protected by a wire fuse link.
Warning about adding auxiliary batteries:
An auxilary battery may be used, however a battery isolation unit is not supplied and the auxiliary battery may discharge the
truck battery when the engine is not running.
Ground Studs on the chassis/frame may be utilized as a grounding point with a 50A Maximum total load, see “Vehicle Ground
Locations” section in the RAM Body Builder Guide, Electrical/Wiring Information.
Date: 07-NOV-2014