LATHE CHUCKS POWER CHUCKS AND HYDRAULIC

Transcription

LATHE CHUCKS POWER CHUCKS AND HYDRAULIC
CONTENTS
pages
04 - 94
09
86
1
pages
87 - 144
95
131
2
3
MACHINE AND BENCH VISES
VICES
pages
133 - 200
145
184
MILLING FIXTURES
pages
185 - 222
201
204
4
VDI - TOOLHOLDERS
pages
205 - 251
223
231
5
LATHE CHUCKS
POWER CHUCKS AND HYDRAULIC CYLINDERS
7
LATHE CHUCKS
9
LATHE CHUCKS - CONTENTS
10
LATHE CHUCKS - CONTENTS
11
LATHE CHUCKS - CONTENTS
Precision self-centering scroll chucks
3 jaw
DIN 6350
steel body
3504-I, 3505-I
19
DIN 55026
steel body
3514-I, 3515-I
20
DIN 55027
steel body
3534-I, 3535-I
21
DIN 55029
steel body
3544-I, 3545-I
22
DIN 6350
steel body
3574-I, 3575-I
23
steel body
3504, 3505
24
cast iron body
3204, 3205
25
steel body
3514, 3515
26
cast iron body
3214, 3215
27
steel body
3534, 3535
28
cast iron body
3234, 3235
29
steel body
3544, 3545
30
cast iron body
3244, 3245
31
steel body
3574, 3575
32
cast iron body
3274, 3275
33
steel body
3704, 3705
34
cast iron body
3604, 3605
35
steel body
3714, 3715
36
cast iron body
3614, 3615
37
steel body
3734, 3735
38
cast iron body
3634, 3635
39
steel body
3744, 3745
40
cast iron body
3644, 3645
41
steel body
3774, 3775
42
cast iron body
3674, 3675
43
Standard self-centering scroll chucks
3 jaw
DIN 6350
DIN 55026
DIN 55027
DIN 55029
DIN 6350
4 jaw
DIN 6350
DIN 55026
DIN 55027
DIN 55029
DIN 6350
http://www.bison-bial.com, e-mail:[email protected] tel.+48 857 416 420
12
LATHE CHUCKS - CONTENTS
Standard self-centering scroll chucks
2 jaw
DIN 6350
steel body
3105
44
steel body
3804, 3805
45
cast iron body
3806, 3807
46
6 jaw
DIN 6350
Self-centering chucks with fine adjustment
3 jaw
steel body
3564, 3565
47
steel body
3864, 3865
48
cast iron body
3264, 3265
49
6 jaw
3 jaw
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
13
LATHE CHUCKS - CONTENTS
Scroll chucks for sharpening drills
3 jaw
3266, 3866
50
6 jaw
3867, 3868
51
Collet chucks
3911, 3960
51
3286
52
Self-centering scroll chucks for small turning diameter
Engineering data for standard self-centering scroll chucks:
- Gripping ranges
53
- Maximum permissible rotational speeds
53
- Total gripping force
54
- Balance value
54
- Centering accuracy
54
Spare parts for standard self-centering scroll chucks:
- Main dimensions of hard solid jaws and soft solid jaws for chucks type 3200, 3500, 3700, 3864
55
- Mounting dimensions of hard master jaws for chucks type 3100, 3200, 3500, 3600, 3700, 3865
59
- Mounting dimensions of top jaws for chucks 3100, 3200, 3500, 3600, 3700, 3865
60
Lathe chucks with Morse taper
9154, 9155, 9156,
9164, 9165
61
Lathe chucks with Morse taper
9184, 9185, 9186, 9187
62
4954, 4956
62
Independent lathe chucks with Morse taper
Self-centering and individually adjustable scroll chucks
3 jaw
DIN 6351
steel body
4705
cast iron body
4505
steel body
4805
cast iron body
4605
63
4 jaw
DIN 6351
http://www.bison-bial.com, e-mail:[email protected] tel.+48 857 416 420
14
63
LATHE CHUCKS - CONTENTS
Self-centering chucks with large through hole for pipe machining
3 jaw
DIN 6350
iron body
3295
64
DIN 6350
steel body
3597
65
DIN 55026
steel body
3515 HD
66
Self-centering chucks with large through hole for pipe machining
4 jaw
DIN 6350
steel body
4307 HD 3564, 3565
67
DIN 55026
steel body
4317 HD
68
DIN 55029
steel body
4347 HD
69
steel body
4304, 4305
70
cast iron body
4302, 4303
71
steel body
4314, 4315
72
cast iron body
4312, 4313
73
steel body
4334, 4335
74
cast iron body
4332, 4333
75
steel body
4344, 4345
76
cast iron body
4342, 4343
77
4317-800/15 MSP
78
Independent chucks
4 jaw
DIN 6350
DIN 55026
DIN 55027
DIN 55029
DIN 55026
steel body
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
15
LATHE CHUCKS - CONTENTS
Engineering data for independent chucks:
Gripping ranges
79
Maximum permissible rotational speeds
79
Spare parts for independent chucks:
Main dimensions of one-piece & two- piece reversible jaws
81
Mounting bolts for top jaws
82
Self-centering wedge bar chucks
3 jaw
DIN 6350
steel body
3404
83
DIN 55026
steel body
3414
83
DIN 55027
steel body
3434
83
DIN 55026
steel body
3444
83
Main dimensions of wedge bar chucks
83
Engineering data for self-centering wedge bar chucks:
Gripping ranges
steel body
85
Maximum permissible rotational speeds
steel body
85
Total gripping force
steel body
85
Balance value
steel body
85
Centering accuracy
steel body
85
Spare parts for self-centering wedge bar chucks
86
Adapter plates
Fully-machined adapter plates
8200
87
Semi-finished adapter plates
8200
89
Fully-finished adapter plates
8200-X
90
Machine spindle noses to DIN and ANSI standards
http://www.bison-bial.com, e-mail:[email protected] tel.+48 857 416 420
16
93
BISON – SELF- CENTERING SCROLL CHUCKS
Hardened components and
basic surfaces ground
Surfaces hardened
and ground
Type 3500, 3700 chucks
A PROVEN DESIGN (THE CUSHMAN TYPE) FOR UNIVERSAL USE
BUILT IN THREE MAIN LINES :
- standard chucks - with cast iron body for normal use
- precision chucks - with steel body for precision and high precision machining; extended period of life - expectancy
- super precision chucks - with adjustment
All components which are important for transmitting the chucking force are of modern and compact design.
BODY
- type 3500, 3700 chucks - drop-forged of the highest grade steel, hardened and ground
- type 3200, 3600 chucks - high quality cast-iron
SCROLL PLATE
- drop-forged of fine alloy steel, carburized and hardened
- thread flanks ground on both sides
JAWS
- of fine alloy steel, teeth, guides and other working surfaces carburized, hardened and ground
PINIONS
- of alloy steel, carburized, hardened and ground
- pinions are recessed into the chuck body and a special safety spring is mounted on the operating wrench,
preventing accidents
Each scroll plate and assembled precision chuck are statically balanced within fine limits.
Lathe chucks must be orricated regulary to maintain their gripping force.
Directions are included in the operating instructions supplied with each chuck.
All chucks are equipped with grease nipples for convenient maintenance.
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
17
SELF-CENTERING SCROLL CHUCKS
GUIDE FOR USE OF HAND-OPERATED BISON CHUCKS,
SELF-CENTERING AND INDEPENDENT CHUCKS
Range of application, special features
Machining of flange-type workpieces
Bar or tubework
3500 Ist
class
accuracy
3200
3600
3500
3700
3105
3264, 3265
3564, 3565
3864, 3865












Machining of parts requiring
a very high concentricity accuracy

Twist drill grinding

Clamping of parts on grinding machines

3266, 3868
3866, 3867

Machining of workpieces requiring
a very high speed

Measuring and inspection works














Normal application


Particularly suitable
Possible, with reservations
http://www.bison-bial.com, e-mail:[email protected] tel.+48 857 416 420
18
4300

Machining of eccentrical parts, of assymetrical and irregularly shaped workpieces
Machining of workpieces requiring
especially high gripping force
4505, 4605
4705, 4805





PRECISION SELF-CENTERING SCROLL CHUCKS
Type 3504-I, 3505-I
3 JAWS, STEEL BODY (DIN 6350)
ø 80 - ø 400
ø 500 - ø 630
Features
■■ 3 jaw, self-centering scroll chuck with manual clamping
■■ Steel body extends machine life while providing higher rigidity
and greater wear resistance, enabling the chuck to withstand
higher machining forces
■■ Hardened and ground working surfaces ensure longer life with
maintained accuracy and repeatability
■■ Balanced scroll plate allows higher rotation speeds without
excess vibration
■■ Mounted on the machine-tool spindle from the back of the
chuck, using the adaptor plate
Application
■■ This first class chuck, with increased clamping accuracy, is
made for very high precision machining on conventional lathes
and milling fixtures
Options
■■ Hard solid jaws (type 3504-I) or hard two-piece jaws (type
3505-I)
■■ Chuck size: can be greater than 630 mm, but not exceeding
1000 mm
■■ Chuck design: our engineers can work with you to implement
any product design changes you may require
Chuck size A
80
100
125
160
200
250
400
500
630
B
B1
C
D H7
E
F
G
H
J
K
L
Approx. weight
(kg)
44
3
56
16
67
3xM6
32
13
-
50
3
70
20
83
3xM8
42
17
-
59,5
64,3
4
95
35,5
108
3xM8
51
20
56
40
68
72,8
4
125
42
140
6xM10
70
32
67
43
78
82,8
4
160
55
176
6xM10
85
29
80
45
89
92,8
5
200
76
224
6xM12
105
34
95
53
109
116,8
5
330
136
362
6xM16
145
55
127
67
119
129,8
5
420
190
458
6xM16
180
60
127
79
129
140,3
7
545
252
586
6xM16
225
70
127
87
1,5
2,8
5,0
10,0
17,5
29
85
145,0
250,0
Type 3505-I
1 set of outside
hard solid jaws
1 set of inside
hard solid jaws
1 wrench
1 set of hard
top jaws
1 set of hard
master jaws
1 wrench
Optional
accessories
Type 3504-I
Standard
accessories
Other engineering data - see pages 53-54
1 set of soft solid
jaws
1 set of soft
top jaws
Spare parts - see pages 55-57
Example of order: 3504-80-I
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
19
PRECISION SELF-CENTERING SCROLL CHUCKS
Type 3514-I, 3515-I
3 JAWS, STEEL BODY (DIN 55026)
*
( )
- Screws inside taper
type A1
Features
■■ 3 jaw, self-centering scroll chuck with manual clamping
■■ Steel body extends machine life while providing higher rigidity
and greater wear resistance, enabling the chuck to withstand
higher machining forces
Chuck size A
160
Short taper
1:4
B
B1
min
D
max
E
F1
G1
F
*5
5
*6
68
72,8
82,563
82,578
42
61,9
M10
-
78
82,8
82,563
106,375
82,578
106,390
42
55
61,9
82,6
M10
M12
-
82,563
82,578
76
104,8
89
92,8
106,375
106,390
55
82,6
M12
-
Qty. of mounting
screws
3
3
3
G
H
J
K
L
Approx. weight
(kg)
70
32
67
43
10,0
200
*5
250
*6
85
29
80
45
■■ Hardened and ground working surfaces ensure longer life with
maintained accuracy and repeatability
■■ Balanced scroll plate allows higher rotation speeds without
excess vibration
■■ Mounted directly to “A” type machine-tool spindles
Application
■■ This first class chuck, with increased clamping accuracy, is
made for very high precision machining on conventional lathes
and grinders
Options
■■ Hard solid jaws (type 3514-I) or hard two-piece jaws (type
3515-I)
■■ Chuck size: can be greater than 630 mm, but not exceeding
1000 mm
■■ Chuck design: our engineers can work with you to implement
any product design changes you may require
85
29
80
45
M10
105
34
95
53
19,0
315
*8
139,719
139,734
76
111,1
M16
-
6
105
34
95
53
*8
8
500
*11
8
630
11
11
15
96,2
101,3
106,375
139,719
106,390
139,734
103
80
111,1
M16
133,4
-
108
116,8
139,719
196,869
139,734
196,887
136
130
165,1
M 20
171,4
-
119
129,8
139,719
196,869
139,734
196,887
136
190
171,4
235
129
140,3
196,869 285,775
196,887 285,795
252
190
235
330,2
6
6
6
6
6
105
34
95
53
400
M12
125
43
110
57
32,0
125
43
110
57
55,0
M16
145
55
127
67
145
55
127
67
M16
180
60
127
79
92,0
M20
180
60
127
79
160,0
M20
225
70
127
87
M24
225
70
127
87
285,0
Type 3515-I
1 set of outside
hard solid jaws
1 set of inside
hard solid jaws
1 wrench
1 set of hard
top jaws
1 set of hard
master jaws
1 wrench
Optional
accessories
Type 3514-I
Standard
accessories
Other engineering data - see pages 53-54
Spare parts - see pages 55-57
Example of order: 3514-160-I
http://www.bison-bial.com, e-mail:[email protected] tel.+48 857 416 420
20
1 set of soft solid
jaws
1 set of soft
top jaws
PRECISION SELF-CENTERING SCROLL CHUCKS
Type 3534-I, 3535-I
3 JAWS, STEEL BODY (DIN 55027)
Features
■■ 3 jaw, self-centering scroll chuck with manual clamping
■■ Steel body extends machine life while providing higher rigidity
and greater wear resistance, enabling the chuck to withstand
higher machining forces
■■ Hardened and ground working surfaces ensure longer life with
maintained accuracy and repeatability
Chuck size A
Short taper
1:4
B
B1
min
D
max
E
F
Qty. of mounting
screws
H
J
K
L
Approx. weight
(kg)
125
3
160
4
4
59,5
64,8
53,975 63,513
53,988 63,526
32
75
85
200
5
68
72,8
63,513 82,563
63,526 82,578
42
85
104,8
5
■■ Balanced scroll plate allows higher rotation speeds without
excess vibration
■■ Mounted directly to BAYONET type machine-tool spindles
Application
■■ This first class chuck, with increased clamping accuracy, is
made for very high precision machining on conventional lathes
Options
■■ Hard solid jaws (type 3534-I) or hard two-piece jaws (type
3535-I)
■■ Chuck size: can be greater than 630 mm, but not exceeding
1000 mm
■■ Chuck design: our engineers can work with you to implement
any product design changes you may require
250
6
6
315
8
8
400
11
8
500
11
8
630
11
11
15
78
89
96,2
111,7
108
119
129
82,8
92,8
101,3
116,8
116,8
129,8
140,3
82,563 106,375 106,375 139,719 139,719 196,869 139,719 196,869 139,719 196,869 196,869 285,775
82,578 106,390 106,390 139,734 139,734 196,887 139,734 196,887 139,734 196,887 196,887 285,795
55
76
103
136
136
190
190
252
104,8
133,4
133,4
171,4
171,4
235
171,4
235
171,4
235
235
330,2
3
3
3
4
4
4
4
4
4
6
4
4
4
6
6
6
51
20
56
40
51
20
56
40
70
32
67
43
70
32
67
43
85
29
80
45
85
29
80
45
105
34
95
53
105
34
95
53
125
43
110
57
125
43
110
57
145
55
127
67
145
55
127
67
180
60
127
79
180
60
127
79
225
70
127
87
225
70
127
87
5,0
9,0
19,0
32,0
51,0
101,0
150,0
274,0
Type 3535-I
1 set of outside
hard solid jaws
1 set of inside
hard solid jaws
1 wrench
1 set of hard
top jaws
1 set of hard
master jaws
1 wrench
Optional
accessories
Type 3534-I
Standard
accessories
Other engineering data - see pages 53-54
1 set of soft solid
jaws
1 set of soft
top jaws
Spare parts - see pages 55-58
Example of order: 3534-160/4-I
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
21
PRECISION SELF-CENTERING SCROLL CHUCKS
Type 3544-I, 3545-I
3 JAWS, STEEL BODY (DIN 55029)
■■ Balanced scroll plate allows higher rotation speeds without
excess vibration
■■ Mounted directly to CAMLOCK type machine-tool spindles
Application
■■ This first class chuck, with increased clamping accuracy, is
made for very high precision machining on conventional lathes
Options
■■ Hard solid jaws (type 3544-I) or hard two-piece jaws (type
3545-I)
■■ Chuck size: can be greater than 400 mm, but not exceeding
1000 mm
■■ Chuck design: our engineers can work with you to implement
any product design changes you may require
Features
■■ 3 jaw, self-centering scroll chuck with manual clamping
■■ Steel body extends machine life while providing higher rigidity
and greater wear resistance, enabling the chuck to withstand
higher machining forces
■■ Hardened and ground working surfaces ensure longer life with
maintained accuracy and repeatability
Chuck size A
Short taper 1:4
B
B1
min
D
max
E
F
Qty. of mounting screws
H
J
K
L
Approx. weight (kg)
Chuck size A
Short taper 1:4
B
B1
min
D
max
E
F
Qty. of mounting screws
H
J
K
L
Approx. weight (kg)
100
3
76
53,975
53,988
20
70,6
3
70
32
67
43
3,0
6
106,375
106,390
103
133,4
6
125
43
110
57
125
3
53,975
53,988
70,6
3
51
20
56
40
96,2
101,3
59,5
64,8
32
5,0
315
8
139,719
139,734
4
3
63,513
63,526
53,975
53,988
82,6
3
51
20
56
40
70,6
3
70
32
67
43
160
4
68
72,8
63,513
63,526
42
82,6
3
70
32
67
43
9,0
5
4
82,563
82,578
63,513
63,526
104,8
6
70
32
67
43
82,6
3
85
29
80
45
400
11
111,7
116,8
196,869
196,887
139,719
139,734
235
6
125
43
110
57
171,4
6
145
55
127
67
171,4
6
125
43
110
57
51,0
8
108
116,8
136
101,0
200
5
78
82,8
82,563
82,578
55
104,8
6
85
29
80
45
19,0
250
6
6
106,375
106,390
106,375
106,390
133,4
6
85
29
80
45
133,4
6
105
34
95
53
500
11
8
196,869
196,887
139,719
139,734
136
171,4
6
180
60
127
79
235
6
145
55
127
67
119
129,8
150,0
11
8
196,869
196,887
190
235
6
180
60
127
79
139,719
139,734
136
171,4
6
225
70
127
87
630
11
129
140,3
196,869
196,887
190
235
6
225
70
127
87
274,0
89
92,8
76
32,0
8
139,719
139,734
171,4
6
105
34
95
53
15
285,775
285,795
252
330,2
6
225
70
127
87
Type 3545-I
1 set of outside
hard solid jaws
1 set of inside
hard solid jaws
1 wrench
1 set of hard
top jaws
1 set of hard
master jaws
1 wrench
Optional
accessories
Type 3544-I
Standard
accessories
Other engineering data - see pages xx - xx
Spare parts - see pages 55-58
Example of order: 3544-100/3-I
http://www.bison-bial.com, e-mail:[email protected] tel.+48 857 416 420
22
1 set of soft solid
jaws
1 set of soft
top jaws
PRECISION SELF-CENTERING SCROLL CHUCKS
Type 3574-I, 3575-I
3 JAWS, STEEL BODY (DIN 6350)
Features
■■ 3 jaw, self-centering scroll chuck with manual clamping
■■ Steel body extends machine life while providing higher rigidity
and greater wear resistance, enabling the chuck to withstand
higher machining forces
■■ Hardened and ground working surfaces ensure longer life with
maintained accuracy and repeatability
■■ Balanced scroll plate allows higher rotation speeds without
excess vibration
■■ Flexible mounting system: mounted on machine-tool spindle
using adaptor plate and can be mounted either from the back
or the from the front of the chuck to the adaptor plate
Application
■■ This first class chuck, with increased clamping accuracy,
is made for very high precision machining on conventional
lathes, grinders and milling fixtures
■■ Can be used on CNC lathes, in place of power chucks
Options
■■ Hard solid jaws (type 3574-I) or hard two-piece jaws (type
3575-I)
■■ Chuck size: can be greater than 630 mm, but not exceeding
1000 mm
■■ Chuck design: our engineers can work with you to implement
any product design changes you may require
Chuck size A
80
100
125
160
200
250
315
400
500
630
B
B1
C
D H7
E
F
G
H
J
K
L
P
44
3
56
16
67
3xM6
32
13
3xM6
50
3
70
20
83
3xM8
42
17
3xM8
59,5
64,3
4
95
35,5
108
3xM8
51
20
56
40
3xM8
68
72,8
4
125
42
140
6xM10
70
32
67
43
3xM10
78
82,8
4
160
55
176
6xM10
85
29
80
45
3xM10
89
92,8
5
200
76
224
6xM12
105
34
95
53
3xM12
97,2
101,3
5
260
103
286
6xM16
125
43
110
57
3xM16
109
116,8
5
330
136
362
6xM16
145
55
127
67
3xM16
119
129,8
5
420
190
458
6xM16
180
60
127
79
3xM16
129
140,3
7
545
252
586
6xM16
225
70
127
87
3xM16
Approx. weight
(kg)
1,5
2,8
5,0
10,0
17,5
29
50
85
85
250
Approx. weight
(kg)
1,5
2,8
5,0
10,0
17,5
29
50
85
145,0
250,0
Type 3575-I
1 set of outside
hard solid jaws
1 set of inside
hard solid jaws
1 wrench
1 set of hard
top jaws
1 set of hard
master jaws
1 wrench
Optional
accessories
Type 3574-I
Standard
accessories
Other engineering data - see pages 53-54
1 set of soft solid
jaws
1 set of soft
top jaws
Spare parts - see pages 55-57
Example of order: 3574-80-I
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
23
STANDARD SELF- CENTERING SCROLL CHUCKS
Type 3504, 3505
3 JAWS, STEEL BODY (DIN 6350)
ø 80 - ø 400
ø 500 - ø 400
Features
■■ 3 jaw, self-centering scroll chuck with manual clamping
■■ Steel body extends machine life while providing higher rigidity
and greater wear resistance, enabling the chuck to withstand
higher machining forces
■■ Hardened and ground working surfaces ensure longer life with
maintained accuracy and repeatability
■■ Balanced scroll plate allows higher rotation speeds without
excess vibration
■■ Mounted on the machine-tool spindle from the back of the
chuck, using the adaptor plate
Application
■■ This first class chuck, with increased clamping accuracy, is
made for very high precision machining on conventional lathes
and milling fixtures
Options
■■ Hard solid jaws (type 3504) or hard two-piece jaws (type 3505)
■■ Chuck size: can be greater than 400 mm, but not exceeding
1000 mm
■■ Chuck design: our engineers can work with you to implement
any product design changes you may require
Chuck size A
80
100
125
160
200
250
315
400
B
B1
C
D H7
E
F
G
H
J
K
L
Approx. weight (kg)
44
3
56
16
67
3xM6
32
13
1,5
50
3
70
20
83
3xM8
42
17
2,8
59,5
64,3
4
95
35,5
108
3xM8
51
20
56
40
5,0
68
72,8
4
125
42
140
6xM10
70
32
67
43
10,0
78
82,8
4
160
55
176
6xM10
85
29
80
45
17,5
89
92,8
5
200
76
224
6xM12
105
34
95
53
29
97,2
101,3
5
260
103
286
6xM16
125
43
110
57
50
109
116,8
5
330
136
362
6xM16
145
55
127
67
85
Type 3505
1 set of outside
hard solid jaws
1 set of inside
hard solid jaws
1 wrench
1 set of hard
top jaws
1 set of hard
master jaws
1 wrench
Optional
accessories
Type 3504
Standard
accessories
Other engineering data - see pages 53-54
Spare parts - see pages 55-57
Example of order: 3504 - 80
http://www.bison-bial.com, e-mail:[email protected] tel.+48 857 416 420
24
1 set of soft solid
jaws
1 set of soft
top jaws
STANDARD SELF-CENTERING SCROLL CHUCKS
Type 3204, 3205
3 JAWS, CAST IRON BODY (DIN 6350)
Features
■■ 3 jaw, self-centering scroll chuck with manual clamping, and a high
quality cast iron body
■■ Simply designed, allowing inner parts to be replaced quickly
■■ Mounted on the machine-tool spindle from the back of the chuck, using
the adaptor plate
(*)
Application
■■ This chuck is designed for all types of workshop machining operations
on conventional lathes, grinders and milling fixtures
Options
■■ Hard solid jaws (type 3205) or hard two-piece jaws (type 3205)
■■ Chuck design: our engineers can work with you to implement any
product design changes you may require
3204-800, 915,1000; 3205-800, 915,1000
(*)
Chuck size A
80
100
110
125
140
160
200
250
315
400
500
630
800
915
1000
B
44
50
50
56
60
64,5
75
85
94
105
120
135
159
171
171
B1
-
-
-
60,8
64,8
69,3
79,8
88,8
99,1
113,8
130,8
146,3
170,3
180
180
C
3
3
4
4
4
4
4
5
5
5
5
7
20
20
20
D H7
56
70
80
95
105
125
160
200
260
330
420
545
450
520
520
E
16
20
27
32
40
42
55
76
103
136
190
252
320
408
408
F
67
83
95
108
120
140
176
224
286
362
458
586
368,3
463,6
463,6
G
3xM6
3xM8
3xM8
3xM8
3xM8
6xM10
6xM10
6xM12
6xM16
6xM16
6xM16
6xM16
-
-
-
H
32
42
42
51
51
70
85
105
125
145
180
225
225
-
-
J
13
17
17
20
20
32
29
34
43
55
60
70
70
-
-
K
-
-
-
56
56
67
80
95
110
127
127
127
127
175
175
L
-
-
-
40
40
43
45
53
57
67
79
87
87
100
100
Approx. weight
(kg)
1,5
2,8
3,4
5,0
6,0
10,0
17,5
29
50
85
145,0
250,0
402
560
720
Type 3205
1 set of outside
hard solid jaws
1 set of inside
hard solid jaws
1 wrench
1 set of hard
top jaws
1 set of hard
master jaws
1 wrench
Optional
accessories
Type 3204
Standard
accessories
Other engineering data - see pages 53-54
1 set of soft solid
jaws
1 set of soft
top jaws
Spare parts - see pages 55-57
Example of order: 3204-100
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
25
STANDARD SELF- CENTERING SCROLL CHUCKS
Type 3514, 3515
3 JAWS, STEEL BODY (DIN 55026)
*
( )
*
- Screws inside taper type A1
Features
■■ 3 jaw, self-centering scroll chuck with manual clamping
■■ Steel body extends machine life while providing higher rigidity
and greater wear resistance, enabling the chuck to withstand
higher machining forces
■■ Hardened and ground working surfaces ensure longer life with
maintained accuracy and repeatability
Chuck size A
160
Short taper 1:4
*5
B
B1
E
F1
G1
F
68
72,8
82,563
82,578
42
61,9
M10
-
Qty. of mounting
screws
3
G
H
J
K
L
Approx. weight (kg)
70
32
67
43
10,0
min
max
D
200
4
*5
63,513
63,526
42
82,6
78
82,8
82,563
82,578
42
61,9
M10
-
250
*6
106,375
106,390
55
82,6
M12
-
3
M10
85
29
80
45
85
29
80
45
19,0
■■ Balanced scroll plate allows higher rotation speeds without
excess vibration
■■ Mounted directly to “A” type machine-tool spindles
Application
■■ This first class chuck, with increased clamping accuracy, is
made for very high precision machining on conventional lathes
and grinders
Options
■■ Hard solid jaws (type 3514) or hard two-piece jaws (type 3515)
■■ Chuck size: can be greater than 400 mm, but not exceeding
1000 mm
■■ Chuck design: our engineers can work with you to implement
any product design changes you may require
5
*6
82,563
82,578
76
104,8
89
92,8
106,375
106,390
55
82,6
M12
-
3
85
29
80
45
M10
105
34
95
53
315
*8
139,719
139,734
76
111,1
M16
-
6
*8
96,2
101,3
106,375
139,719
106,390
139,734
103
80
111,1
M16
133,4
-
6
105
34
95
53
32,0
400
6
8
*11
106,375
106,390
103
133,4
108
116,8
139,719
139,734
136
171,4
196,869
196,887
130
165,1
M 20
-
6
105
34
95
53
M12
125
43
110
57
6
125
43
110
57
M12
145
55
127
67
55,0
M16
145
55
127
67
92,0
145
55
127
67
Type 3515
1 set of outside
hard solid jaws
1 set of inside
hard solid jaws
1 wrench
1 set of hard
top jaws
1 set of hard
master jaws
1 wrench
Optional
accessories
Type 3514
Standard
accessories
Other engineering data - see pages 53-54
Spare parts - see pages 55-57
Example of order: 3514-160/5
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
26
1 set of soft solid
jaws
1 set of soft
top jaws
STANDARD SELF-CENTERING SCROLL CHUCKS
Type 3214, 3215
3 JAWS, CAST IRON BODY (DIN 55026)
*
( )
*
Features
■■ 3 jaw, self-centering, scroll chuck with manual clamping, and a high
quality cast iron body
■■ Simply designed, allowing inner parts to be replaced quickly
■■ Mounted directly to “A” type machine-tool spindles
Application
■■ This chuck is designed for all types of workshop machining operations
on conventional lathes and grinders
Options
■■ Hard solid jaws (type 3214) or hard two-piece jaws (type 3215)
■■ Chuck design: our engineers can work with you to implement any
product design changes you may require
- Screws inside taper type A1
Chuck
size A
160
Short taper
1:4
B
*5
*5
81,5
91
B1
86,3
200
250
*6
5
95,8
315
*6
*8
400
6
*8
6
8
500
*11
630
8
11
11
800
*15
103,5
117,7
128,5
146
165
107,3
122,8
137,3
157,3
175,8
11
*15
159
915
1000
20
20
20
180
171
171
180
180
191,3
min 82,563 82,563 106,375 82,563 106,375 139,719 106,375 139,719 106,375 139,719 196,869 139,719 196,869 196,869 285,775 196,869 285,775 412,775 412,775 412,775
D
max 82,578 82,578 106,390 82,578 106,390 139,734 106,390 139,734 106,390 139,734 196,887 139,734 196,887 196,887 285,795 196,887 285,795 412,802 412,802 412,802
E
42
42
55
76
55
76
103
80
103
136
130
136
190
190
190
320
408
408
F1
61,9
61,9
82,6
-
82,6
111,1
-
111,1
-
-
165,1
-
-
-
-
-
247,6
-
-
-
G1
M10
M10
M12
-
M12
M16
-
M16
-
-
M 20
-
-
-
-
-
M 24
-
-
-
F
Qty. of
mounting
screws
G
-
-
-
104,8
-
-
133,4
-
133,4
171,4
-
171,4
235
235
330,2
235
-
368,3
463,6
463,6
3
3
3
3
6
6
-
-
-
M10
-
-
M12
-
M12
M16
-
M16
M20
M20
M24
M20
-
M24
M24
M24
H
70
85
85
105
105
105
125
125
145
145
145
180
180
225
225
225
225
225
-
-
J
32
29
29
34
34
34
43
43
55
55
55
60
60
70
70
70
70
70
-
-
6
6
6
6
190
6
6
K
67
80
80
95
95
95
110
110
127
127
127
127
127
127
127
127
127
127
-
-
L
43
45
45
53
53
53
57
57
67
67
67
79
79
87
87
87
87
87
-
-
Approx.
weight (kg)
10,0
720
720
19,0
32,0
55,0
92,0
160,0
285,0
384,0
Type 3215
1 set of outside
hard solid jaws
1 set of inside
hard solid jaws
1 wrench
1 set of hard
top jaws
1 set of hard
master jaws
1 wrench
Optional
accessories
Type 3214
Standard
accessories
Other engineering data - see pages 53-54
1 set of soft solid
jaws
1 set of soft
top jaws
Spare parts - see pages 55-57
Example of order: 3215-160/5
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
27
STANDARD SELF-CENTERING SCROLL CHUCKS
Type 3534, 3535
3 JAWS, STEEL BODY (DIN 55027)
Features
■■ 3 jaw, self-centering scroll chuck with manual clamping
■■ Steel body extends machine life while providing higher rigidity
and greater wear resistance, enabling the chuck to withstand
higher machining forces
■■ Hardened and ground working surfaces ensure longer life with
maintained accuracy and repeatability
Chuck size A
Short taper
1:4
B
B1
min
D
max
E
F
Qty. of mounting
screws
H
J
K
L
125
3
160
4
53,975
53,988
5
5
68
72,8
63,513
63,526
63,513
63,526
85
85
32
75
200
4
59,5
64,8
■■ Balanced scroll plate allows higher rotation speeds without
excess vibration
■■ Mounted directly to BAYONET type machine-tool spindles
Application
■■ This first class chuck, with increased clamping accuracy, is
made for very high precision machining on conventional lathes
Options
■■ Hard solid jaws (type 3534) or hard two-piece jaws (type 3535)
■■ chuck size: can be greater than 400 mm, but not exceeding
1000 mm
■■ Chuck design: our engineers can work with you to implement
any product design changes you may require
250
6
6
106,375
106,390
89
92,8
106,375
106,390
76
133,4
78
82,8
82,563
82,578
82,563
82,578
104,8
104,8
42
55
133,4
315
8
139,719
139,734
171,4
6
8
96,2
101,3
106,375
139,719
106,390
139,734
103
133,4
171,4
400
11
111,7
116,8
196,869
196,887
235
8
11
108
116,8
139,719
196,869
139,734
196,887
136
171,4
235
3
3
3
4
4
4
4
4
4
4
6
4
6
51
20
56
40
51
20
56
40
70
32
67
43
70
32
67
43
85
29
80
45
85
29
80
45
105
34
95
53
105
34
95
53
125
43
110
57
125
43
110
57
125
43
110
57
145
55
127
67
145
55
127
67
Approx. weight
(kg)
5,0
9,0
19,0
32,0
51,0
101,0
Type 3535
1 set of outside
hard solid jaws
1 set of inside
hard solid jaws
1 wrench
1 set of hard
top jaws
1 set of hard
master jaws
1 wrench
Optional
accessories
Type 3534
Standard
accessories
Other engineering data - see pages 53-54
Spare parts - see pages 55-58
Example of order: 3534-125/3
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
28
1 set of soft solid
jaws
1 set of soft
top jaws
STANDARD SELF-CENTERING SCROLL CHUCKS
Type 3234, 3235
3 JAWS, CAST IRON BODY (DIN 55027)
Features
■■ 3 jaw, self-centering, scroll chuck with manual clamping, and a high
quality cast iron body
■■ Simply designed, allowing inner parts to be replaced quickly
■■ Mounted directly to BAYONET type machine-tool spindles
Application
■■ This chuck is designed for all types of workshop machining operations
on conventional lathes
Options
■■ Hard solid jaws (type 3234) or hard two-piece jaws (type 3235)
■■ Chuck size: can be greater than 630 mm, but not exceeding 1000 mm
■■ Chuck design: our engineers can work with you to implement any
product design changes you may require
Chuck size A
100
Short taper
1:4
B
B1
min
D
max
E
F
Qty. of mounting screws
H
J
K
L
Approx. weight (kg)
3
125
160
3
80
53,975
53,988
20
75
3
42
17
3,0
4
53,975
53,988
75
3
51
20
56
40
70
74,8
32
53,975
53,988
63,513
63,526
85
3
51
20
56
40
75
3
70
32
67
43
85
3
70
32
67
43
5,0
Short taper
1:4
B
B1
min
D
max
E
F
Qty. of mounting screws
H
J
K
L
Approx. weight (kg)
6
200
4
63,513
63,526
250
Chuck size A
3
5
81,5
86,3
42
9,0
8
6
3
82,563
82,578
106,375
106,390
104,8
4
70
32
67
43
133,4
4
70
32
67
43
315
103,5
107,3
106,375
139,719
106,390
139,734
76
133,4
171,4
4
4
105
105
34
34
95
95
53
53
32,0
6
4
53,975
53,988
51,5
75
3
85
29
80
45
400
8
11
117,7
122,8
106,375
139,719
106,390
139,734
103
133,4
171,4
4
4
125
125
43
43
110
110
57
57
51,0
125
130
196,869
196,887
235
6
125
43
110
57
6
106,375
106,390
103
133,4
4
145
55
127
67
171,4
4
145
55
127
67
101,0
85
3
85
29
80
45
19,0
5
6
82,563
82,578
55
104,8
4
85
29
80
45
106,375
106,390
500
8
128,5
137,3
139,719
139,734
63,513
63,526
91
95,8
11
136
196,869
196,887
235
6
145
55
127
67
8
133,4
4
85
29
80
45
630
11
146
156,8
139,719
196,869
139,734
196,887
136
190
171,4
235
4
6
180
180
60
60
127
127
79
79
150,0
11
15
165
176,3
196,869
285,775
196,887
285,795
190
252
235
330,2
6
6
225
225
70
70
127
127
87
87
274,0
Type 3215
1 set of outside
hard solid jaws
1 set of inside
hard solid jaws
1 wrench
1 set of hard
top jaws
1 set of hard
master jaws
1 wrench
Optional
accessories
Type 3214
Standard
accessories
Other engineering data - see pages 53-54
1 set of soft solid
jaws
1 set of soft
top jaws
Spare parts - see pages 55-58
Example of order:3234-100/3
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
29
STANDARD SELF-CENTERING SCROLL CHUCKS
Type 3544, 3545
3 JAWS, STEEL BODY (DIN 55029)
Features
■■ 3 jaw, self-centering scroll chuck with manual clamping
■■ Steel body extends machine life while providing higher rigidity
and greater wear resistance, enabling the chuck to withstand
higher machining forces
■■ Hardened and ground working surfaces ensure longer life with
maintained accuracy and repeatability
■■ Balanced scroll plate allows higher rotation speeds without
excess vibration
■■ Mounted directly to CAMLOCK type machine-tool spindles
Chuck size A
Short taper
1:4
B
B1
min
D
max
E
F
125
3
160
4
59,5
64,8
53,975
63,513
53,988
63,526
32
70,6
82,6
3
4
53,975
53,988
68
72,8
63,513
63,526
42
82,6
70,6
Application
■■ This first class chuck, with increased clamping accuracy, is
made for very high precision machining on conventional lathes
Options
■■ Hard solid jaws (type 3544) or hard two-piece jaws (type 3545)
■■ Chuck size: can be greater than 400 mm, but not exceeding
1000 mm
■■ Chuck design: our engineers can work with you to implement
any product design changes you may require
200
5
4
82,563
82,578
104,8
63,513
63,526
55
82,6
250
5
6
78
82,8
82,563
82,578
106,375
106,390
104,8
133,4
6
315
8
89
92,8
106,375 139,719
106,390 139,734
76
133,4
171,4
6
8
96,2
101,3
106,375 139,719
106,390 139,734
103
133,4
171,4
400
11
111,7
116,8
196,869
196,887
235
8
11
108
116,8
139,719 196,869
139,734 196,887
136
171,4
235
Qty. of mounting
screws
3
3
3
3
6
3
6
6
6
6
6
6
6
6
6
H
J
K
L
Approx. weight
(kg)
51
20
56
40
51
20
56
40
70
32
67
43
70
32
67
43
70
32
67
43
85
29
80
45
85
29
80
45
85
29
80
45
105
34
95
53
105
34
95
53
125
43
110
57
125
43
110
57
125
43
110
57
145
55
127
67
145
55
127
67
5,0
9,0
19,0
32,0
51,0
101,0
Type 3545
1 set of outside
hard solid jaws
1 set of inside
hard solid jaws
1 wrench
1 set of hard
top jaws
1 set of hard
master jaws
1 wrench
Optional
accessories
Type 3544
Standard
accessories
Other engineering data - see pages 53-54
Spare parts - see pages 55-58
Example of order: 3544-125/4
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
30
1 set of soft solid
jaws
1 set of soft
top jaws
STANDARD SELF-CENTERING SCROLL CHUCKS
Type 3244, 3245
3 JAWS, CAST IRON BODY (DIN 55029)
Features
■■ 3 jaw, self-centering, scroll chuck with manual clamping, and a high
quality cast iron body
■■ Simply designed, allowing inner parts to be replaced quickly
■■ Mounted directly to CAMLOCK type machine-tool spindles
Application
■■ This chuck is designed for all types of workshop machining operations
on conventional lathes
Options
■■ Hard solid jaws (type 3244) or hard two-piece jaws (type 3245)
■■ Chuck size: can be greater than 630 mm, but not exceeding 1000 mm
■■ Chuck design: our engineers can work with you to implement any
product design changes you may require
Chuck size A
100
Short taper
1:4
B
B1
min
D
max
E
F
Qty. of mounting screws
H
J
K
L
Approx. weight (kg)
80
53,975
53,988
20
70,6
3
42
17
3,0
125
3
Chuck size A
160
3
4
53,975
53,988
70,6
3
51
20
56
40
70
74,8
32
3
63,513
63,526
5,0
82,6
3
51
20
56
40
250
Short taper
1:4
B
B1
min
D
max
E
F
Qty. of mounting screws
H
J
K
L
Approx. weight (kg)
5
104,8
6
105
34
95
53
4
53,975
53,988
42
70,6
3
70
32
67
43
5
81,5
86,3
63,513
63,526
8
103,5
107,3
106,375
106,390
76
133,4
6
105
34
95
53
32,0
139,719
139,734
171,4
6
105
34
95
53
6
3
82,563
82,578
82,6
3
70
32
67
43
9,0
53,975
53,988
51,5
70,6
3
85
29
80
45
104,8
6
70
32
67
43
315
6
82,563
82,578
200
4
63,513
63,526
82,6
3
85
29
80
45
400
8
11
117,7
122,8
106,375
139,719
106,390
139,734
103
133,4
171,4
6
6
125
125
43
43
110
110
57
57
51,0
140
145
196,869
196,887
235
6
125
43
110
57
6
106,375
106,390
103
133,4
6
145
55
127
67
91
95,8
19,0
5
6
82,563
82,578
55
104,8
6
85
29
80
45
106,375
106,390
133,4
6
85
29
80
45
500
8
11
128,5
137,3
139,719
139,734
171,4
6
145
55
127
67
101,0
136
196,869
196,887
235
6
145
55
127
67
8
630
11
146
156,8
139,719
196,869
139,734
196,887
136
190
171,4
235
6
6
180
180
60
60
127
127
79
79
150,0
11
15
165
176,3
196,869
285,775
196,887
285,795
190
252
235
330,2
6
6
225
225
70
70
127
127
87
87
274,0
Type 3245
1 set of outside
hard solid jaws
1 set of inside
hard solid jaws
1 wrench
1 set of hard
top jaws
1 set of hard
master jaws
1 wrench
Optional
accessories
Type 3244
Standard
accessories
Other engineering data - see pages 53-54
1 set of soft solid
jaws
1 set of soft
top jaws
Spare parts - see pages 55-58
Example of order: 3244-100/3
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
31
STANDARD SELF- CENTERING SCROLL CHUCKS
Type 3574, 3575
3 JAWS, STEEL BODY (DIN 6350)
Features
■■ 3 jaw, self-centering scroll chuck with manual clamping
■■ Steel body extends machine life while providing higher rigidity
and greater wear resistance, enabling the chuck to withstand
higher machining forces
■■ Hardened and ground working surfaces ensure longer life with
maintained accuracy and repeatability
■■ Balanced scroll plate allows higher rotation speeds without
excess vibration
■■ Flexible mounting system: mounted on machine-tool spindle
using adaptor plate and can be mounted either from the back
or the from the front of the chuck to the adaptor plate
Application
■■ This first class chuck, with increased clamping accuracy,
is made for very high precision machining on conventional
lathes, grinders and milling fixtures
■■ Can be used on CNC lathes, in place of power chucks
Options
■■ Hard solid jaws (type 3574) or hard two-piece jaws (type 3575)
■■ Chuck size: can be greater than 400 mm, but not exceeding
1000 mm
■■ Chuck design: our engineers can work with you to implement
any product design changes you may require
Chuck size A
80
100
125
160
200
250
315
400
B
B1
C
D H7
E
F
G
H
J
K
L
P
44
3
56
16
67
3xM6
32
13
3xM6
50
3
70
20
83
3xM8
42
17
3xM8
59,5
64,3
4
95
35,5
108
3xM8
51
20
56
40
3xM8
68
72,8
4
125
42
140
6xM10
70
32
67
43
3xM10
78
82,8
4
160
55
176
6xM10
85
29
80
45
3xM10
89
92,8
5
200
76
224
6xM12
105
34
95
53
3xM12
97,2
101,3
5
260
103
286
6xM16
125
43
110
57
3xM16
109
116,8
5
330
136
362
6xM16
145
55
127
67
3xM16
Approx. weight
(kg)
1,5
2,8
5,0
10,0
17,5
29
50
85
Type 3575
1 set of outside
hard solid jaws
1 set of inside
hard solid jaws
1 wrench
1 set of hard
top jaws
1 set of hard
master jaws
1 wrench
Optional
accessories
Type 3574
Standard
accessories
Other engineering data - see pages 53-54
Spare parts - see pages 55-57
Example of order: 3574 - 80
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
32
1 set of soft solid
jaws
1 set of soft
top jaws
STANDARD SELF-CENTERING SCROLL CHUCKS
Type 3274, 3275
3 JAWS, CAST IRON BODY (DIN 6350)
Application
■■ This chuck is designed for all types of workshop machining
operations on conventional lathes , grinders and milling
fixtures
■■ Can be used on CNC lathes, in place of power chucks
Features
■■ 3 jaw, self-centering, scroll chuck with manual clamping, and a
high quality cast iron body
■■ Simply designed, allowing inner parts to be replaced quickly
■■ Flexible mounting system: mounted on machine-tool spindle
using adaptor plate and can be mounted either from the back
or the from the front of the chuck to the adaptor plate
Chuck size A
80
85
100
B
44
44
B1
-
-
Options
■■ Hard solid jaws (type 3274) or hard two-piece jaws (type 3275)
■■ Chuck size: can be greater than 630 mm, but not exceeding
1000 mm
■■ Chuck design: our engineers can work with you to implement
any product design changes you may require
125
160
200
250
315
400
500
630
50
56
64,5
75
85
94
105
120
135
-
60,8
69,3
79,8
88,8
99,1
113,8
130,8
146,3
C
3
3
3
4
4
4
5
5
5
5
7
D H7
56
62
70
95
125
160
200
260
330
420
545
E
16
18
20
32
42
55
76
103
136
190
252
F
67
72
83
108
140
176
224
286
362
458
586
G
3xM6
-
3xM8
3xM8
6xM10
6xM10
6xM12
6xM16
6xM16
6xM16
6xM16
H
32
32
42
51
70
85
105
125
145
180
225
J
13
43
17
20
32
29
34
43
55
60
70
K
-
-
-
56
67
80
95
110
127
127
127
L
-
-
-
40
43
45
53
57
67
79
87
P
3xM6
3xM6
3xM8
3xM8
3xM10
3xM10
3xM12
3xM16
3xM16
6xM16
6xM16
Approx. weight
(kg)
1,5
1,9
2,8
5,0
10,0
17,5
29
50
85
145,0
250,0
Type 3275
1 set of outside
hard solid jaws
1 set of inside
hard solid jaws
1 wrench
1 set of hard
top jaws
1 set of hard
master jaws
1 wrench
Optional
accessories
Type 3274
Standard
accessories
Other engineering data - see pages 53-54
1 set of soft solid
jaws
1 set of soft
top jaws
Spare parts - see pages 55-57
Example of order: 3274 - 80
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
33
STANDARD SELF-CENTERING SCROLL CHUCKS
Type 3704, 3705
4 JAWS, STEEL BODY, (DIN 6350)
Features
■■ 4 jaw, self-centering scroll chuck with manual clamping
■■ Steel body extends machine life while providing higher rigidity
and greater wear resistance, enabling the chuck to withstand
higher machining forces
■■ Hardened and ground working surfaces ensure longer life with
maintained accuracy and repeatability
■■ Balanced scroll plate allows higher rotation speeds without
excess vibration
■■ Mounted on the machine-tool spindle from the back of the
chuck, using the adaptor plate
Application
■■ This first class chuck, with increased clamping accuracy, is
made for very high precision machining on conventional lathes
and milling fixtures
■■ Suitable for machining square and round workpieces, granting
greater flexibility to machining operations
Options
■■ Hard solid jaws (type 3704) or hard two-piece jaws (type 3705)
■■ Chuck size: can be greater than 630 mm, but not exceeding
1000 mm
■■ Chuck design: our engineers can work with you to implement
any product design changes you may require
Chuck size A
100
125
160
200
250
315
400
500
630
B
B1
C
D H7
E
F
G
H
J
K
L
50
3
70
20
83
3xM8
42
17
-
59,5
64,3
4
95
35,5
108
3xM8
51
20
56
40
68
72,8
4
125
42
140
6xM10
70
32
67
43
78
82,8
4
160
55
176
6xM10
85
29
80
45
89
92,8
5
200
76
224
6xM12
105
34
95
53
97,2
101,3
5
260
103
286
6xM16
125
43
110
57
109
116,8
5
330
136
362
6xM16
145
55
127
67
119
129,8
5
420
190
458
6xM16
180
60
127
79
129
140,3
7
545
252
586
6xM16
225
70
127
87
Approx. weight
(kg)
2,8
5,0
10,0
17,5
29
50
85
145,0
250,0
Type 3705
1 set of outside
hard solid jaws
1 set of inside
hard solid jaws
1 wrench
1 set of hard
top jaws
1 set of hard
master jaws
1 wrench
Optional
accessories
Type 3704
Standard
accessories
Other engineering data - see pages 53-54
Spare parts - see pages 55-57
Example of order: 3704 - 100
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
34
1 set of soft solid
jaws
1 set of soft
top jaws
STANDARD SELF-CENTERING SCROLL CHUCKS
Type 3604, 3605
4 JAWS, CAST IRON BODY (DIN 6350)
Application
■■ Suitable for machining square and round workpieces, granting
greater flexibility to machining operations
■■ This chuck is designed for all types of workshop machining
operations on conventional lathes, grinders and milling fixtures
Features
■■ 4 jaw, self-centering, scroll chuck with manual clamping, and a
high quality cast iron body
■■ Simply designed, allowing inner parts to be replaced quickly
■■ Mounted on the machine-tool spindle from the back of the
chuck, using the adaptor plate
Chuck size A
100
110
B
50
50
B1
-
-
125
Options
■■ Hard solid jaws (type 3604) or hard two-piece jaws (type 3605)
■■ Chuck size: can be greater than 630 mm, but not exceeding
1000 mm
■■ Chuck design: our engineers can work with you to implement
any product design changes you may require
140
160
200
250
315
400
500
630
56
60
64,5
75
85
94
105
120
135
60,8
64,8
69,3
79,8
88,8
99,1
113,8
130,8
146,3
C
3
4
4
4
4
4
5
5
5
5
7
D H7
70
80
95
105
125
160
200
260
330
420
545
E
20
27
32
40
42
55
76
103
136
190
252
F
83
95
108
120
140
176
224
286
362
458
586
G
3xM8
3xM8
3xM8
3xM8
6xM10
6xM10
6xM12
6xM16
6xM16
6xM16
6xM16
H
42
42
51
51
70
85
105
125
145
180
225
J
17
17
20
20
32
29
34
43
55
60
70
K
-
-
56
56
67
80
95
110
127
127
127
L
-
-
40
40
43
45
53
57
67
79
87
Approx. weight (kg)
2,8
3,4
5,0
6,0
10,0
17,5
29
50
85
145,0
250,0
Type 3605
1 set of outside
hard solid jaws
1 set of inside
hard solid jaws
1 wrench
1 set of hard
top jaws
1 set of hard
master jaws
1 wrench
Optional
accessories
Type 3604
Standard
accessories
Other engineering data - see pages 53-54
1 set of soft solid
jaws
1 set of soft
top jaws
Spare parts - see pages 55-57
Example of order: 3604 - 100
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
35
STANDARD SELF-CENTERING SCROLL CHUCKS
Type 3714, 3715
4 JAWS, STEEL BODY (DIN 55026)
*
( )
*
- Screws inside taper type A1
Features
■■ 4 jaw, self-centering scroll chuck with manual clamping
■■ Steel body extends machine life while providing higher rigidity
and greater wear resistance, enabling the chuck to withstand
higher machining forces
■■ Hardened and ground working surfaces ensure longer life with
maintained accuracy and repeatability
■■ Balanced scroll plate allows higher rotation speeds without
excess vibration
Chuck size A
160
Short taper
1:4
B
B1
min
D
max
E
F1
G1
F
*5
68
72,8
82,563
82,578
42
61,9
M10
-
Qty. of mounting
screws
3
G
H
J
K
L
Approx. weight (kg)
70
32
67
43
10,0
200
*5
250
*6
106,375
106,390
55
82,6
M12
3
*6
82,563
82,578
76
104,8
89
92,8
106,375
106,390
55
82,6
M12
-
3
85
29
80
45
85
29
80
45
19,0
315
5
78
82,8
82,563
82,578
42
61,9
M10
-
■■ Mounted directly to “A” type machine-tool spindles
Application
■■ This first class chuck, with increased clamping accuracy, is
made for very high precision machining on conventional lathes
and grinders
■■ Suitable for machining square and round workpieces, granting
greater flexibility to machining operations
Options
■■ Hard solid jaws (type 3714) or hard two-piece jaws (type 3715)
■■ Chuck size: can be greater than 630 mm, but not exceeding
1000 mm
■■ Chuck design: our engineers can work with you to implement
any product design changes you may require
*8
139,719
139,734
76
111,1
M16
-
6
105
34
95
53
32,0
*8
96,2
101,3
106,375
139,719
106,390
139,734
103
80
111,1
M16
133,4
-
6
M10
105
34
95
53
400
6
8
106,375
106,390
103
133,4
108
116,8
139,719
139,734
136
171,4
6
105
34
95
53
M12
125
43
110
57
630
*11
11
196,869
196,887
130
165,1
M 20
-
129
140,3
196,869
196,887
190
235
6
125
43
110
57
M12
145
55
127
67
M16
145
55
127
67
92,0
55,0
6
145
55
127
67
M20
225
70
127
87
285,0
Type 3715
1 set of outside
hard solid jaws
1 set of inside
hard solid jaws
1 wrench
1 set of hard
top jaws
1 set of hard
master jaws
1 wrench
Optional
accessories
Type 3714
Standard
accessories
Other engineering data - see pages 53-54
Spare parts - see pages 55-57
Example of order: 3714-160/5
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
36
1 set of soft solid
jaws
1 set of soft
top jaws
STANDARD SELF-CENTERING SCROLL CHUCKS
Type 3614, 3615
4 JAWS, CAST IRON BODY (DIN 55026)
*
( )
*
Features
■■ 4 jaw, self-centering, scroll chuck with manual clamping, and a high
quality cast iron body
■■ Simply designed, allowing inner parts to be replaced quickly
■■ Mounted directly to “A” type machine-tool spindles
Application
■■ Suitable for machining square and round workpieces, granting greater
flexibility to machining operations
■■ This chuck is designed for all types of workshop machining operations
on conventional lathes and grinders
Options
■■ Hard solid jaws (type 3614) or hard two-piece jaws (type 3615)
■■ Chuck size: can be greater than 500 mm, but not exceeding 1000 mm
■■ Chuck design: our engineers can work with you to implement any
product design changes you may require
- Screws inside taper type A1
Chuck size A
200
Short taper
1:4
B
*6
91
103,5
117,7
128,5
146
B1
95,8
107,3
122,8
137,3
157,3
D
250
5
*6
315
*8
400
6
*8
6
8
500
*11
8
11
min
106,375
82,563
106,375
139,719
106,375
139,719
106,375
139,719
196,869
139,719
196,869
max
106,390
82,578
106,390
139,734
106,390
139,734
106,390
139,734
196,887
139,734
196,887
E
55
76
55
76
103
80
103
136
130
136
190
F1
82,6
-
82,6
111,1
-
111,1
-
-
165,1
-
-
G1
M12
-
M12
M16
-
M16
-
-
M 20
-
-
F
-
104,8
-
-
133,4
-
133,4
171,4
-
171,4
235
8
4
8
8
4
4
8
-
M10
-
-
M12
-
M12
M16
-
M16
M20
H
85
105
105
105
125
125
145
145
145
180
180
J
29
34
34
34
43
43
55
55
55
60
60
K
80
95
95
95
110
110
127
127
127
127
127
L
45
53
53
53
57
57
67
67
67
79
Approx. weight (kg)
19,0
Qty. of mounting
screws
G
4
32,0
55,0
92,0
79
160,0
Type 3615
1 set of outside
hard solid jaws
1 set of inside
hard solid jaws
1 wrench
1 set of hard
top jaws
1 set of hard
master jaws
1 wrench
Optional
accessories
Type 3614
Standard
accessories
Other engineering data - see pages 53-54
1 set of soft solid
jaws
1 set of soft
top jaws
Spare parts - see pages 55-57
Example of order: 3614-200/8
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
37
STANDARD SELF-CENTERING SCROLL CHUCKS
Type 3734, 3735
4 JAWS, STEEL BODY (DIN 55027)
Features
■■ 4 jaw, self-centering scroll chuck with manual clamping
■■ Steel body extends machine life while providing higher rigidity
and greater wear resistance, enabling the chuck to withstand
higher machining forces
Chuck size A
Short taper 1:4
B
B1
min
D
max
E
F
125
160
3
4
59,5
64,8
53,975 63,513
53,988 63,526
32
75
85
200
4
5
68
72,8
63,513 82,563
63,526 82,578
42
85
104,8
■■ Hardened and ground working surfaces ensure longer life with
maintained accuracy and repeatability
■■ Balanced scroll plate allows higher rotation speeds without
excess vibration
■■ Mounted directly to BAYONET type machine-tool spindles
Application
■■ This first class chuck, with increased clamping accuracy, is
made for very high precision machining on conventional lathes
■■ Suitable for machining square and round workpieces, granting
greater flexibility to machining operations
Options
■■ Hard solid jaws (type 3734) or hard two-piece jaws (type 3735)
■■ Chuck size: can be greater than 630 mm, but not exceeding
1000 mm
■■ Chuck design: our engineers can work with you to implement
any product design changes you may require
250
315
400
500
630
5
6
6
8
6
8
8
11
8
11
11
15
78
89
96,2
108
119
129
82,8
92,8
101,3
116,8
129,8
140,3
82,563 106,375 106,375 139,719 106,375 139,719 139,719 196,869 139,719 196,869 196,869 285,775
82,578 106,390 106,390 139,734 106,390 139,734 139,734 196,887 139,734 196,887 196,887 285,795
55
76
103
136
136
190
190
252
104,8
133,4
133,4
171,4
133,4
171,4
171,4
235
171,4
235
235
330,2
Qty. of mounting
screws
3
3
3
4
4
4
4
4
4
4
4
6
4
6
6
6
H
J
K
L
Approx. weight (kg)
51
20
56
40
51
20
56
40
70
32
67
43
70
32
67
43
85
29
80
45
85
29
80
45
105
34
95
53
105
34
95
53
125
43
110
57
125
43
110
57
145
55
127
67
145
55
127
67
180
60
127
79
180
60
127
79
225
70
127
87
225
70
127
87
5,0
9,0
19,0
32,0
51,0
101,0
150,0
274,0
Type 3735
1 set of outside
hard solid jaws
1 set of inside
hard solid jaws
1 wrench
1 set of hard
top jaws
1 set of hard
master jaws
1 wrench
Optional
accessories
Type 3734
Standard
accessories
Other engineering data - see pages 53-54
Spare parts - see pages 55-58
Example of order: 3734-125/4
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
38
1 set of soft solid
jaws
1 set of soft
top jaws
STANDARD SELF-CENTERING SCROLL CHUCKS
Type 3634, 3635
4 JAWS, CAST IRON BODY (DIN 55027)
Features
■■ 4 jaw, self-centering, scroll chuck with manual clamping, and a high
quality cast iron body
■■ Simply designed, allowing inner parts to be replaced quickly
■■ Mounted directly to BAYONET type machine-tool spindles
Application
■■ This chuck is designed for all types of workshop machining operations
on conventional lathes
Options
■■ Hard solid jaws (type 3634) or hard two-piece jaws (type 3635)
■■ Chuck size: can be greater than 500 mm, but not exceeding 1000 mm
■■ Chuck design: our engineers can work with you to implement any
product design changes you may require
Chuck size A
125
Short taper 1:4
B
B1
min
D
max
E
F
Qty. of mounting screws
H
J
K
L
Approx. weight (kg)
160
3
4
3
63,513
63,526
53,975
53,988
63,513
63,526
85
3
51
20
56
40
75
3
70
32
67
43
85
3
70
32
67
43
32
4
82,563
82,578
106,375
106,390
104,8
4
70
32
67
43
133,4
4
70
32
67
43
6
103,5
107,3
53,975
53,988
51,5
75
3
85
29
80
45
63,513
63,526
106,375
106,390
171,4
4
105
34
95
53
133,4
4
125
43
110
57
76
139,719
139,734
103
32,0
82,563
82,578
55
104,8
4
85
29
80
45
106,375
106,390
85
3
85
29
80
45
400
8
6
117,7
122,8
139,719
139,734
6
171,4
4
125
43
110
57
133,4
4
85
29
80
45
19,0
315
8
5
91
95,8
9,0
250
6
133,4
4
105
34
95
53
3
42
5,0
106,375
106,390
6
81,5
86,3
75
3
51
20
56
40
Chuck size A
Short taper 1:4
B
B1
min
D
max
E
F
Qty. of mounting screws
H
J
K
L
Approx. weight (kg)
5
70
74,8
53,975
53,988
200
4
106,375
106,390
103
133,4
4
145
55
127
67
51,0
500
8
128,5
137,3
139,719
139,734
11
11
146
156,8
196,869
196,887
136
171,4
4
145
55
127
67
101,0
8
235
6
145
55
127
67
139,719
139,734
136
171,4
4
180
60
127
79
196,869
196,887
190
235
6
180
60
127
79
150,0
Type 3635
1 set of outside
hard solid jaws
1 set of inside
hard solid jaws
1 wrench
1 set of hard
top jaws
1 set of hard
master jaws
1 wrench
Optional
accessories
Type 3634
Standard
accessories
Other engineering data - see pages 53-54
1 set of soft solid
jaws
1 set of soft
top jaws
Spare parts - see pages 55-58
Example of order: 3634-125/4
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
39
STANDARD SELF-CENTERING SCROLL CHUCKS
Type 3744, 3745
4 JAWS, STEEL BODY (DIN 55029)
Features
■■ 4 jaw, self-centering scroll chuck with manual clamping
■■ Steel body extends machine life while providing higher rigidity
and greater wear resistance, enabling the chuck to withstand
higher machining forces
■■ Hardened and ground working surfaces ensure longer life with
maintained accuracy and repeatability
■■ Balanced scroll plate allows higher rotation speeds without
excess vibration
■■ Mounted directly to CAMLOCK type machine-tool spindles
Chuck size A
125
160
Application
■■ This first class chuck, with increased clamping accuracy, is
made for very high precision machining on conventional lathes
■■ Suitable for machining square and round workpieces, granting
greater flexibility to machining operations
Options
■■ Hard solid jaws (type 3744) or hard two-piece jaws (type 3745)
■■ Chuck size: can be greater than 630 mm, but not exceeding
1000 mm
■■ Chuck design: our engineers can work with you to implement
any product design changes you may require
200
250
315
400
500
630
Short taper 1:4
3
4
3
4
5
4
5
6
6
8
6
8
8
11
8
11
11
15
B
59,5
68
78
89
96,2
108
119
129
B1
64,8
72,8
82,8
92,8
101,3
116,8
129,8
140,3
min
53,975 63,513 53,975 63,513 82,563 63,513 82,563 106,375 106,375 139,719 106,375 139,719 139,719 196,869 139,719 196,869 196,869 285,775
D
max
53,988 63,526 53,988 63,526 82,578 63,526 82,578 106,390 106,390 139,734 106,390 139,734 139,734 196,887 139,734 196,887 196,887 285,795
E
32
42
55
76
103
136
136
190
190
252
F
70,6
82,6
70,6
82,6
104,8
82,6
104,8 133,4 133,4 171,4 133,4 171,4 171,4
235
171,4
235
235
330,2
Qty. of mounting
screws
3
3
3
3
6
3
6
6
6
6
6
6
6
6
6
6
6
6
H
J
K
L
Approx. weight
(kg)
51
20
56
40
51
20
56
40
70
32
67
43
70
32
67
43
70
32
67
43
85
29
80
45
85
29
80
45
85
29
80
45
105
34
95
53
105
34
95
53
125
43
110
57
125
43
110
57
145
55
127
67
145
55
127
67
180
60
127
79
180
60
127
79
225
70
127
87
225
70
127
87
5,0
9,0
19,0
32,0
51,0
101,0
150,0
274,0
Type 3745
1 set of outside
hard solid jaws
1 set of inside
hard solid jaws
1 wrench
1 set of hard
top jaws
1 set of hard
master jaws
1 wrench
Optional
accessories
Type 3744
Standard
accessories
Other engineering data - see pages 53-54
Spare parts - see pages 55-58
Example of order: 3744-125/3
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
40
1 set of soft solid
jaws
1 set of soft
top jaws
STANDARD SELF-CENTERING SCROLL CHUCKS
Type 3644, 3645
4 JAWS, CAST IRON BODY (DIN 55029)
Features
■■ 4 jaw, self-centering, scroll chuck with manual clamping, and a high
quality cast iron body
■■ Simply designed, allowing inner parts to be replaced quickly
■■ Mounted directly to CAMLOCK type machine-tool spindles
Application
■■ Suitable for machining square and round workpieces, granting greater
flexibility to machining operations
■■ This chuck is designed for all types of workshop machining operations
on conventional lathes
Options
■■ Hard solid jaws (type 3644) or hard two-piece jaws (type 3645)
■■ Chuck size: can be greater than 315 mm, but not exceeding 1000
■■ Chuck design: our engineers can work with you to implement any
product design changes you may require
Chuck size A
125
Short taper 1:4
B
B1
min
D
max
E
F
Qty. of mounting screws
H
J
K
L
Approx. weight (kg)
3
53,975
53,988
70,6
3
51
20
56
40
Chuck size A
70
74,8
32
5,0
160
4
3
63,513
63,526
53,975
53,988
82,6
3
51
20
56
40
70,6
3
70
32
67
43
400
Short taper 1:4
B
B1
min
D
max
E
F
Qty. of mounting screws
H
J
K
L
Approx. weight (kg)
6
106,375
106,390
103
133,4
6
145
55
127
67
8
128,5
137,3
139,719
139,734
171,4
6
145
55
127
67
101,0
200
4
81,5
86,3
63,513
63,526
42
82,6
3
70
32
67
43
9,0
5
3
4
82,563
82,578
53,975
53,988
51,5
70,6
3
85
29
80
45
63,513
63,526
104,8
6
70
32
67
43
500
136
11
8
196,869
196,887
139,719
139,734
136
171,4
6
180
60
127
79
235
6
145
55
127
67
146
156,8
150,0
91
95,8
82,6
3
85
29
80
45
19,0
5
6
82,563
82,578
55
104,8
6
85
29
80
45
106,375
106,390
250
11
5
196,869
196,887
190
235
6
180
60
127
79
82,563
82,578
104,8
6
105
34
95
53
6
103,5
107,3
106,375
106,390
76
133,4
6
105
34
95
53
32,0
133,4
6
85
29
80
45
315
8
6
139,719
139,734
106,375
106,390
171,4
6
105
34
95
53
133,4
6
125
43
110
57
117,7
122,8
103
51,0
8
139,719
139,734
171,4
6
125
43
110
57
Type 3645
1 set of outside
hard solid jaws
1 set of inside
hard solid jaws
1 wrench
1 set of hard
top jaws
1 set of hard
master jaws
1 wrench
Optional
accessories
Type 3644
Standard
accessories
Other engineering data - see pages 53-54
1 set of soft solid
jaws
1 set of soft
top jaws
Spare parts - see pages 55-58
Example of order: 3644-125/4
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
41
STANDARD SELF-CENTERING SCROLL CHUCKS
Type 3774, 3775
4 JAWS, STEEL BODY (DIN 6350)
Features
■■ 4 jaw, self-centering scroll chuck with manual clamping
■■ Steel body extends machine life while providing higher rigidity
and greater wear resistance, enabling the chuck to withstand
higher machining forces
■■ Hardened and ground working surfaces ensure longer life with
maintained accuracy and repeatability
■■ Balanced scroll plate allows higher rotation speeds without
excess vibration
■■ Flexible mounting system: mounted on machine-tool spindle
using adaptor plate and can be mounted either from the back
or the from the front of the chuck to the adaptor plate
Application
■■ This first class chuck, with increased clamping accuracy,
is made for very high precision machining on conventional
lathes, grinders and milling fixtures
■■ Suitable for machining square and round workpieces, granting
greater flexibility to machining operations
■■ Can be used on CNC lathes, in place of power chucks
Options
■■ Hard solid jaws (type 3774) or hard two-piece jaws (type 3775)
■■ Chuck size: can be greater than 400 mm, but not exceeding
1000 mm
■■ Chuck design: our engineers can work with you to implement
any product design changes you may require
Chuck size A
160
200
250
315
400
B
B1
C
D H7
E
F
G
H
J
K
L
P
Approx. weight (kg)
68
72,8
4
125
42
140
6xM10
70
32
67
43
3xM10
10,0
78
82,8
4
160
55
176
6xM10
85
29
80
45
3xM10
17,5
89
92,8
5
200
76
224
6xM12
105
34
95
53
3xM12
29
97,2
101,3
5
260
103
286
6xM16
125
43
110
57
3xM16
50
109
116,8
5
330
136
362
6xM16
145
55
127
67
3xM16
85
Type 3775
1 set of outside
hard solid jaws
1 set of inside
hard solid jaws
1 wrench
1 set of hard
top jaws
1 set of hard
master jaws
1 wrench
Optional
accessories
Type 3774
Standard
accessories
Other engineering data - see pages 53-54
Spare parts - see pages 55-57
Example of order: 3774 - 160
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
42
1 set of soft solid
jaws
1 set of soft
top jaws
STANDARD SELF-CENTERING SCROLL CHUCKS
Type 3674, 3675
4 JAWS, CAST IRON BODY (DIN 6350)
Features
■■ 4 jaw, self-centering scroll chuck with manual clamping
■■ Steel body extends machine life while providing higher rigidity
and greater wear resistance, enabling the chuck to withstand
higher machining forces
■■ Hardened and ground working surfaces ensure longer life with
maintained accuracy and repeatability
■■ Balanced scroll plate allows higher rotation speeds without
excess vibration
■■ Flexible mounting system: mounted on machine-tool spindle
using adaptor plate and can be mounted either from the back
or the from the front of the chuck to the adaptor plate
Application
■■ This first class chuck, with increased clamping accuracy,
is made for very high precision machining on conventional
lathes, grinders and milling fixtures
■■ Suitable for machining square and round workpieces, granting
greater flexibility to machining operations
■■ Can be used on CNC lathes, in place of power chucks
Options
■■ Hard solid jaws (type 3774) or hard two-piece jaws (type 3775)
■■ Chuck size: can be greater than 400 mm, but not exceeding
1000 mm
■■ Chuck design: our engineers can work with you to implement
any product design changes you may require
Chuck size A
125
160
200
250
315
B
B1
C
D H7
E
F
G
H
J
K
L
P
Approx. weight (kg)
56
60,8
4
95
32
108
3xM8
51
20
56
40
3xM8
5,0
64,5
69,3
4
125
42
140
6xM10
70
32
67
43
3xM10
10,0
75
79,8
4
160
55
176
6xM10
85
29
80
45
3xM10
17,5
85
88,8
5
200
76
224
6xM12
105
34
95
53
3xM12
29
94
99,1
5
260
103
286
6xM16
125
43
110
57
3xM16
50
Type 3675
1 set of outside
hard solid jaws
1 set of inside
hard solid jaws
1 wrench
1 set of hard
top jaws
1 set of hard
master jaws
1 wrench
Optional
accessories
Type 3674
Standard
accessories
Other engineering data - see pages 53-54
1 set of soft solid
jaws
1 set of soft
top jaws
Spare parts - see pages 55-57
Example of order: 3674 - 125
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
43
STANDARD SELF-CENTERING SCROLL CHUCKS
Type 3105
2 JAWS, CAST IRON BODY (DIN 6350)
Features
■■ 2 jaw, self-centering, scroll chuck with manual clamping, and a
high quality cast iron body
■■ Chucks are equipped with soft, steel top jaws, which can be
individually shaped by the user and clamp irregularly-shaped
workpieces
■■ Hard solid jaws (type 3105)
■■ Simply designed, allowing inner parts to be replaced quickly
■■ Mounted on the machine-tool spindle from the back of the
chuck, using the adaptor plate
Application
■■ This chuck is designed for all types of workshop machining
operations on conventional lathes and milling fixtures
Options
■■ Chuck size: can be greater than 400 mm, but not exceeding
1000 mm
■■ Chuck design: our engineers can work with you to implement
any product design changes you may require
Chuck size A
160
200
250
315
B
64,5
75
85
94
400
105
B1
69,3
79,8
88,8
99,1
113,8
C
4
4
5
5
5
D H7
125
160
200
260
330
E
42
55
76
103
136
F
140
176
224
286
362
G
6xM10
6xM10
6xM12
6xM16
6xM16
H
70
85
105
125
145
J
32
29
34
43
55
Approx. weight (kg)
10
17,5
29
50
85
Type 3105
Standard
accessories
Other engineering data - see pages 53-54
1 set of soft top jaws
1 set of hard master jaws
Spare parts - see pages 55-57
Example of order: 3105 - 160
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
44
1 wrench
STANDARD SELF-CENTERING SCROLL CHUCKS
Type 3804, 3805
6 JAWS, CAST IRON BODY (DIN 6350)
Features
■■ 6 jaw, self-centering, scroll chuck with manual clamping, and a
high quality cast iron body
■■ Simply designed, allowing inner parts to be replaced quickly
■■ Mounted on the machine-tool spindle from the back of the
chuck, using the adaptor plate
Application
■■ Clamping force is equally distributed over 6 jaws, allowing
chuck to machine thin-walled workpieces and clamp without
deformation
■■ This chuck is designed for all types of workshop machining
operations on conventional lathes and milling fixtures
Options
■■ Hard solid jaws (type 3804) or hard two-piece jaws (type 3805)
■■ Chuck size: can be greater than 630 mm, but not exceeding
1000 mm
■■ Chuck design: our engineers can work with you to implement
any product design changes you may require
Chuck size A
200
250
315
400
500
630
B
B1
C
D H7
E
F
G
H
J
K
L
Approx. weight (kg)
75
79,8
4
160
55
176
6xM10
85
29
80
45
17,5
85
88,8
5
200
76
224
6xM12
105
34
95
53
29
94
99,1
5
260
103
286
6xM16
125
43
110
57
50
105
113,8
5
330
136
362
6xM16
145
55
127
67
85
120
130,8
5
420
190
458
6xM16
180
60
127
79
145,0
135
146,3
7
545
252
586
6xM16
225
70
127
87
250,0
Type 3805
1 set of outside
hard solid jaws
1 set of inside
hard solid jaws
1 wrench
1 set of hard
top jaws
1 set of hard
master jaws
1 wrench
Optional
accessories
Type 3804
Standard
accessories
Other engineering data - see pages 53-54
1 set of soft solid
jaws
1 set of soft
top jaws
Spare parts - see pages 55-57
Example of order: 3804 - 200
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
45
STANDARD SELF-CENTERING SCROLL CHUCKS
Type 3806, 3807
6 JAWS, STEEL BODY (DIN 6350)
Features
■■ 6 jaw, self-centering scroll chuck with manual clamping
■■ Steel body extends machine life while providing higher rigidity
and greater wear resistance, enabling the chuck to withstand
higher machining forces
■■ Hardened and ground working surfaces ensure longer life with
maintained accuracy and repeatability
■■ Balanced scroll plate allows higher rotation speeds without
excess vibration
■■ Mounted on the machine-tool spindle from the back of the
chuck, using the adaptor plate
Application
■■ This first class chuck, with increased clamping accuracy, is
made for very high precision machining on conventional lathes
and milling fixtures
■■ Clamping force is equally distributed over 6 jaws, allowing
chuck to machine thin-walled workpieces and clamp without
deformation
Options
■■ Large chuck size: can be greater than 630 mm, but not
exceeding 1000 mm
■■ Chuck design: our engineers can work with you to implement
any product design changes you may require
Chuck size A
200
250
315
400
500
630
B
B1
C
D H7
E
F
G
H
J
K
L
Approx. weight (kg)
75
79,8
4
160
55
176
6xM10
85
29
80
45
17,5
85
88,8
5
200
76
224
6xM12
105
34
95
53
29
94
99,1
5
260
103
286
6xM16
125
43
110
57
50
105
113,8
5
330
136
362
6xM16
145
55
127
67
85
120
130,8
5
420
190
458
6xM16
180
60
127
79
145,0
135
146,3
7
545
252
586
6xM16
225
70
127
87
250,0
Type 3807
1 set of outside
hard solid jaws
1 set of inside
hard solid jaws
1 wrench
1 set of hard
top jaws
1 set of hard
master jaws
1 wrench
Optional
accessories
Type 3806
Standard
accessories
Other engineering data - see pages 53-54
Spare parts - see pages 55-57
Example of order: 3806 - 200
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
46
1 set of soft solid
jaws
1 set of soft
top jaws
SELF-CENTERING CHUCKS WITH FINE ADJUSTMENT
Type 3564, 3565
3 JAWS, STEEL BODY, FRONT MOUNTING
Features
■■ 3 jaw, self-centering chuck
■■ Steel body extends machine life while providing higher rigidity
and greater wear resistance, enabling the chuck to withstand
higher machining forces
■■ Hardened and ground working surfaces ensure longer life with
maintained accuracy and repeatability
■■ Balanced scroll plate allows higher rotation speeds without
excess vibration
■■ Repeatability: 0,015 mm
■■ Superior accuracy: small screws on the outside enable the
chuck to be adjusted to position with nearly zero runout
(adjusting accuracy within 0,005 mm)
■■ The clamped workpiece is adjusted to the required
concentricity by means of 4 (8 for size 400, 500, 630) radially
arranged adjusting screws
Application
■■ This first class chuck, with increased clamping accuracy, is
for universal use, but particularly advantageous for grinding
machines, indexing heads and lathes
■■ Especially suitable for machining parts with top concentricity
Options
■■ Hard solid jaws (type 3564) or hard two-piece jaws (type 3565)
■■ Large Chuck size: can be greater than 630 mm, but not
exceeding 1000 mm
■■ Chuck design: our engineers can work with you to implement
any product design changes you may require
Chuck size A
100
125
160
200
250
315
400
500
630
B
C
D
E
F
G
Approx. weight (kg)
68
13
45
20
83
3xM8
3,3
71,5
15
55
35
108
3xM8
5,0
68,6
18
86
42
140
3xM10
9,1
78
20
110
55
176
3xM10
15,5
89
20
145
76
224
3xM12
26,2
96,2
20
180
103
286
3xM16
46,5
123
22
299, 237
136
171,5
6xM16
90,0
144
30
407,16
190
235
6xM20x120
171
150
30
407,16
252
330,2
6xM20x130
302
Type 3565
1 set of outside
hard solid jaws
1 set of inside
hard solid jaws
1 wrench
1 set of hard
top jaws
1 set of hard
master jaws
1 wrench
Optional
accessories
Type 3564
Standard
accessories
Other engineering data - see pages 53-54
1 set of soft solid
jaws
1 set of soft
top jaws
Spare parts - see pages 55-57
Example of order: 3564 - 100
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
47
SELF-CENTERING CHUCKS WITH FINE ADJUSTMENT
Type 3864, 3865
6 JAWS, STEEL BODY, FRONT MOUNTING
Features
■■ 6 jaw, self-centering chuck
■■ Steel body extends machine life while providing higher rigidity
and greater wear resistance, enabling the chuck to withstand
higher machining forces
■■ Hardened and ground working surfaces ensure longer life with
maintained accuracy and repeatability
■■ Balanced scroll plate allows higher rotation speeds without
excess vibration
■■ Repeatability: 0,015 mm
■■ Superior accuracy: small screws on the outside enable the
chuck to be adjusted to position with nearly zero runout
(adjusting accuracy within 0,005 mm)
■■ The clamped workpiece is adjusted to the required
concentricity by means of 4 (8 for size 400, 500, 630) radially
arranged adjusting screws
Application
■■ This first class chuck, with increased clamping accuracy, is
for universal use, but particularly advantageous for grinding
machines, indexing heads and lathes
■■ Especially suitable for machining parts with top concentricity
■■ Clamping force is equally distributed over 6 jaws, allowing
chuck to machine thin-walled workpieces and clamp without
deformation
Options
■■ Hard solid jaws (type 3864) or hard two-piece jaws (type 3865)
■■ Chuck size: can be greater than 630 mm, but not exceeding
1000 mm
■■ Chuck design: our engineers can work with you to implement
any product design changes you may require
Chuck size A
125
160
200
250
315
400
500
630
B
C
D
E
F
G
H
J
K
L
Approx. weight (kg)
71,5
15
55
35
108
3xM8
51
20
56
40
6,2
68,6
18
86
42
140
3xM10
70
32
67
43
10,5
78
20
110
55
176
3xM10
85
29
80
45
17,5
89
20
145
76
224
3xM12
105
34
95
53
33,0
96,2
20
180
103
286
3xM16
125
41
110
56
56,0
123
22
299, 237
136
171,5
6xM16
145
55
127
67
99,0
144
30
407,16
190
235
6xM20x120
180
60
127
79
180
150
30
407,16
252
330,2
6xM20x130
225
70
127
87
326
Type 3865
1 set of outside
hard solid jaws
1 set of inside
hard solid jaws
1 wrench
1 set of hard
top jaws
1 set of hard
master jaws
1 wrench
Optional
accessories
Type 3864
Standard
accessories
Other engineering data - see pages 53-54
Spare parts - see pages 55-57
Example of order: 3864 - 125
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
48
1 set of soft solid
jaws
1 set of soft
top jaws
SELF-CENTERING CHUCKS WITH FINE ADJUSTMENT
Type 3264, 3265
3 JAWS, CAST IRON BODY, FRONT MOUNTING
Features
■■ 3 jaw, self-centering chuck
■■ Repeatability: 0,015 mm
■■ Superior accuracy: chuck can be adjusted to position with nearly zero
runout (adjusting accuracy within 0,005 mm)
■■ The clamped workpiece is adjusted to the required concentricity by
means of 3 tangentially arranged adjusting spindles
■■ Hardened adjusting spindles
■■ Steel adapter plate
Application
■■ This chuck is for universal use, but is particularly advantageous for
grinding machines, indexing heads and lathes
■■ Especially suitable for machining parts with top concentricity
Options
■■ Hard solid jaws (type 3264) or hard two-piece jaws (type 3265)
■■ Chuck size: can be greater than 315 mm, but not exceeding 1000 mm
■■ Chuck design: our engineers can work with you to implement any
product design changes you may require
Chuck size A
80
100
125
160
200
250
315
B
C min
D
E min
F
G
59
3
56
16
67
3xM6
2,8
-
69
4
70
20
83
3xM8
3,5
-
70
5
95
32
108
3xM8
5,6
6,0
80,5
5
125
42
140
3xM10
10
10,5
91
5
160
55
176
3xM10
17,2
18,0
103
6
200
76
224
3XM12
34,5
36,0
120
6
260
103
286
3xM16
57,5
59,0
Approx. weight (kg)
Type 3264
Type 3265
Type 3265
1 set of outside
hard solid jaws
1 set of inside
hard solid jaws
1 wrench
1 set of hard
top jaws
1 set of hard
master jaws
1 wrench
Optional
accessories
Type 3264
Standard
accessories
Other engineering data - see pages 53-54
1 set of soft solid
jaws
1 set of soft
top jaws
Spare parts - see pages 55-57
Example of order: 3264 - 80
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
49
SCROLL CHUCKS FOR SHARPENING DRILLS
Type 3266, 3866
ø 80, 100
Standard
accessories
Application
■■ Lever scroll chuck is specially designed for grinding twist drills and
other cutting tools
Options
■■ Fine adjustment for sizes ø 125, 160 to the required concentricity by
means of 4 radially arranged adjusting screws
Type 3266
1 set of
outside hard
solid jaws
Chuck size
ø 125, 160
1 set of inside
hard solid jaws
1 operating
lever
3 JAWS TYPE 3266
A
B
C
D
E
F
G
80
100
125
160
200
35
40
48
52
66
1,5
2
8
8
13
48
75
70
78,5
115
24
32
38
52
64
39
62
56
65
84
3xM6
3xM8
3xM6
3xM6
3xM8
A
H
J
K
L
80
100
125
160
200
52
85
83
96
147
35
42
51
70
85
13
17
20
33
30
82
102
129
164
205
Operating lever Approx. weight
length
(kg)
100
1,1
125
3,2
160
4,0
200
7,3
200
13,3
Spare parts - see page 55
Standard
accessories
Example of order: 3266 - 80
Type 3866
ø 80, 100
1 set of outside hard
solid jaws
Chuck size
1 operating
lever
6 JAWS TYPE 3866
A
B
C
D
E
F
G
80
100
125
160
35
40
48
52
1,5
2
8
8
48
75
70
78,5
24
32
38
52
39
62
56
65
3xM6
3xM8
3xM6
3xM6
A
H
J
K
L
S
80
100
125
160
52
85
83
96
35
42
50
58
22
25
36
36
82
102
128
164
1-23
1,5-31
2-37
3-51
Example of order: 3866 - 80
ø 125, 160
Chuck size
mm
80
100
125
160
Code No 0642
for chuck type 3866
6-jaw set
985 411 106
985 411 208
985 411 300
985 411 401
Spare parts - hard outside jaws-set
http://www.bison-bial.com, e-mail:[email protected] tel.+48 857 416 420
50
Operating
lever length
100
125
160
200
Approx.
weight (kg)
2,0
2,8
4,0
7,0
SCROLL CHUCKS FOR SHARPENING DRILLS
Type 3867, 3868
Standard
accessories
Features
■■ Plain back (front mounting)
Application
■■ The wrench operated scroll chuck is specially designed for grinding
twist drills and other cutting tools
Options
■■ Additional tool support (type 3868)
Type 3867
1 set of hard solid
jaws
1 wrench
TYPE 3867
Chuck size
85
110
160
A
85
110
160
B
44
50
79
C
3,9
4
4
D
62
86
125
Chuck size
mm
E
F
G
J
K
S
Approx.
weight (kg)
85
110
160
25,5
32,1
51
70
95
140
3xM6
3xM6
3xM10
32
38
51
37
33
51
1-25
2,3-32
2,5-50
1,9
3,5
4,5
Type 3868
Standard
accessories
Example of order: 3867-160
1 set of hard solid
jaws
1 operating
lever
TYPE 3868
Chuck size
85
Operating lever length
100
Approx. weight (kg)
2,5
Example of order: 3868-85
Chuck size
85
110
160
Code No 0642
Code No 0642
for chuck type 3867
for chuck type 3868
985 411 605
985 411 707
985 411 809
985 412 107
-
Spare parts - hard outside jaws-set
5C COLLET CHUCKS
Spring
collet 5C
Type 3911,
3960
Standard
accessories
Features
■■ The simple wrench operated scroll provides uniform, distortion free
clamping of workpieces and low collet exchange times
Application
■■ The type 3911 collet chuck is designed for use with 5C collets and can
be used for turning, facing, boring, grinding and milling operations
■■ Type 3960 allows for fine adjustment to the required concentricity by
means of 4 radially arranged adjusting screws
Type 3911, 3960
1 wrench
TYPE 3911
Chuck size
A
B
C
D
F
G
Approx.
weight (kg)
125
126
107,5
4
95
108
3xM8x45
4,5
Example of order: 3911-125-5C
Spring
collet 5C
TYPE 3960
Chuck size
A
B
C
D
F
G
Approx.
weight (kg)
125
126
117
15
55
108
3xM8x55
5,4
Example of order: 3960 - 125-5C
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
51
SELF-CENTERING SCROLL CHUCKS SPECIALLY DESIGNED
FOR SMALL TURNING DIAMETER
Type 3286
3 JAWS, STEEL BODY, WITH THREADED MOUNTING
Features
■■ Special compact design
■■ Very small turning diameter
■■ Hard revesible jaws
Application
■■ Especially designed for household use and hobbyist pursuits
■■ Suitable for lathes with a threaded spindle
■■ Can be used with both metal and wood
3286 - 49
3286 - 60
Ø 49
Ø 41
M12x1
29
D
D
D =Ø 20 x Ø 75 D= Ø 0,5 x Ø 32
D=Ø 20 x Ø 52
Chuck size
Mounting
Maximum speed (rpm)
Approx. weight (kg)
49
M12x1
4000 min -1
0,5
60
M14x1
4000 min
0,68
-1
Example of order: 3286 - 49
SPARE PARTS
Code No 0642
Type 3286 - 49
Type 3286 - 60
985 399 142
985 399 155
985 399 183
985 399 170
985 399 101
http://www.bison-bial.com, e-mail:[email protected] tel.+48 857 416 420
52
ENGINEERING DATA
FOR STANDARD SELF-CENTERING SCROLL CHUCKS
GRIPPING RANGES FOR CHUCKS TYPE 3200, 3500, 3600, 3700
Chuck size
Hard solid jaws
Hard two-piece
jaws
80
85
100
110
125
140
160
200
d1
d2
d3
d4
d5
d1
d2
d3
d4
d5
2-27
25-50
48-71
22-46
45-69
90
2-40
32-70
64-102
22-60
54-92
121
3-33
32-62
62-93
25-56
56-87
117
3-33
32-62
62-93
25-56
56-87
117
3-50
39-83
80-125
34-74
72-115
3-50
52-96
95-125
34-76
75-118
151
3-50
39-83
80-125
34-74
72-115
151
3-64
50-107
98-160
42-100
94-154
3-64
62-121
115-160
42-97
88-146
204
4-90
60-145
130-200
52-135
120-202
4-90
72-156
133-200
50-130
105-190
246
250
315
400
500
630
800
915
1000
d1
d2
d3
d4
d5
d1
d2
d3
d4
d5
5-118
77-188
160-250
62-174
145-256
5-118
86-197
160-250
58-165
125-235
306
10-131
90-215
190-315
78-200
172-299
10-131
103-226
190-315
65-182
145-265
384
10-180
103-272
230-400
85-252
210-380
10-180
127-294
230-400
72-228
165-329
472
20-235
140-357
276-500
120-335
245-476
20-235
110-400
190-500
120-410
200-485
600
30-335
180-487
345-630
160-465
325-630
30-335
120-570
200-630
140-590
210-665
770
150-482
302-634
468-800
282-614
448-780
150-482
240-724
316-800
252-736
328-812
940
200 - 550
300 - 950
380 - 1025
350 - 1000
450 - 1025
-
250 - 600
350 - 1080
430 - 1150
425 - 1070
500 - 1150
-
max swing dia
Chuck size
Hard solid jaws
Hard two-piece
jaws
max swing dia
GRIPPING RANGES FOR CHUCKS TYPE 3864, 3865
Chuck size
Hard solid jaws
Hard two-piece
jaws
d1
d2
d3
d4
d5
d1
d2
d3
d4
d5
max swing dia
125
160
200
250
315
400
500
630
6-43
42-78
83-120
34-68
74-110
6-43
50-87
94-125
33-70
76-119
151
8-64
52-107
102-160
47-100
98-154
8-64
67-121
118-160
45-97
92-146
204
8-90
64-145
132-200
55-135
121-202
8-90
74-156
134-200
52-130
109-190
246
12-118
82-188
165-250
68-174
150-256
12-118
82-188
164-250
68-174
150-256
306
12-131
95-215
192-315
82-200
178-299
12-131
108-226
153-315
68-182
150-265
384
15-202
140-308
232-400
95-280
213-400
15-202
132-296
236-400
73-252
169-352
472
30-235
152-361
291-500
132-335
270-474
30-235
121-402
197-478
135-413
210-489
600
40-335
192-487
358-630
175-467
340-630
40-335
132-555
210-630
150-585
220-661
770
Do not exceed maximum chucking ranges.
MAXIMUM PERMISSIBLE SPEEDS (rpm)
Chuck size
80, 85
100,110
125
140, 160
200
250
315
400
500
630
800
915
1000
3100*, 3200, 3600
3500, 3700
3564, 3565
3864, 3865
* 4505
* 4605
* 4705
* 4805
5000
7000
4500
6300
6300
4000
5500
5500
3800
3600
4600
4600
3200
3000
4000
4000
2800
2500
2000
3000
2500
2500
3500
3500
2400
2000
1800
2500
2000
2000
2800
2800
2400
1500
1500
2000
1700
1600
2000
2000
1400
1000
1000
1500
1300
1000
1300
1300
900
700
600
1000
800
800
1000
1000
700
540
480
750
660
600
800
400
700
400
600
* For lathe chucks type 3100, 4505, 4605, 4705 and 4805 the specified permissible speeds are only applicable for work-pieces not exceeding a specific unbalance of 25 gmm/kg.
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
53
ENGINEERING DATA
FOR STANDARD SELF-CENTERING SCROLL CHUCKS
TOTAL GRIPPING FORCE FOR CHUCKS TYPE 3100, 3200, 3500, 3600, 3700, 3800
Chuck size
80, 85
100,110
125
140, 160
200
250
315
400
500
630
800
915
1000
torque on wrench
(Nm)
35
50
75
120
160
180
200
280
360
460
500
500
500
total gripping force
(daN)
1000
1700
2400
3100
2400*
3700
2900*
4600
3600*
5500
4400*
6500
4900*
7200
8000
9000
9000
9000
* for 3100
The total gripping force is the sum of all jaw forces acting radially on the stationery workpiece. The specified gripping forces are approximate values.
They apply to chucks in perfect condition which have been orricated with greases recommended in operating instructions.
BALANCE VALUE FOR SELF-CENTERING CHUCKS TYPE 3500, 3700
Chuck size
80
100
125
160
200
250
315
400
500
630
gcm
11
16
23
32
45
63
90
140
300
640
CENTERING ACCURACY FOR SELF-CENTERING CHUCKS TYPE
3200, 3500, 3600, 3700, 3800
Chuck size
mm
d
l
n
p
s
80, 85
100,110
125, 140
160
200
250
315
400
500
630
800
915
1000
10
14
40
40
60
35
63
10
14
18
40
40
75
50
80
18
25
30
60
50
100
62
100
18
30
40
60
50
135
88
100
30
40
53
80
80
162
96
160
30
53
75
80
80
200
150
160
53
75
100
120
125
252
210
250
53
100
125
120
125
282
250
250
75
100
125
160
200
282
300
400
75
125
160
160
200
325
400
400
160
200
250
160
325
500
400
500
250
315
400
160
500
630
500
-
250
315
400
160
500
630
500
-
-
-
120
150
185
225
300
350
400
400
500
630
630
0,15
0,15
0,06
0,15
0,15
0,06
0,15
0,15
0,06
w
Hard solid jaws
Hard two-piece
jaws
3500 class I
a
b
c
0,010
0,013
0,008
0,015
0,018
0,010
0,020
0,023
0,013
0,025
0,028
0,015
0,030
0,033
0,015
0,050
0,055
0,030
0,070
0,075
0,050
3500
3700
3800
a
b
c
0,020
0,025
0,015
0,030
0,035
0,020
0,040
0,045
0,025
0,050
0,055
0,030
0,060
0,065
0,030
0,070
0,040
0,075
0,050
3200
3600
a
b
c
0,020
0,025
0,015
0,030
0,035
0,020
0,040
0,045
0,025
0,050
0,055
0,030
0,060
0,065
0,030
0,10
0,10
0,05
0,10
0,10
0,05
3284
3285
a
b
c
Centering accuracy (mm)
0,05
0,075
0,04
0,08
0,075
0,07
SPINDLE NOSE CENTERING ACCURACY
3500
A, B
3200, 3600, 3700
Ø 80 - 400
0,003 mm
Ø 80 - 160
Ø 500 - 630
0,005 mm
Ø 200 - 800
0,003 mm
0,005 mm
To obtain the specified centering accuracy of a chuck mounted on a machine tool it is necessary:
* to ensure the machine spindle nose runout does not exceed the values specified,
* to meet the basic requirements for correct mounting of chuck on the spindle nose,
according to the chuck installation instructions.
http://www.bison-bial.com, e-mail:[email protected] tel.+48 857 416 420
54
SPARE PARTS FOR SELF-CENTERING LATHE CHUCKS
HARD OUTSIDE SOLID JAWS - SETS 1)
Chuck size
mm
80
100
110
125
140
160
200
250
315
400
500
630
800
Code No 0642
Code No 0642
Code No 0642
Code No 0642
For chuck
type 3200, 3500
3-jaw set
985 350 009
985 350 100
985 352 306
985 350 202
985 352 601
985 350 304
985 350 406
985 350 508
985 350 600
985 350 701
985 350 803
985 350 905
985 352 000
For chuck
type 3600, 3700
4-jaw set
985 381 970*
985 389 704
985 390 205
985 389 806
985 390 307
985 390 409
985 390 500
985 390 602
985 390 704
985 390 806
985 390 819
-
For chuck
type 3864
6-jaw set
985 400 209
985 400 300
985 400 402
985 400 504
985 400 606
985 400 708
985 400 800
985 349 009
-
For chuck
type 3266
3-jaw set
985 350 024
985 350 126
985 350 228
985 350 304
985 350 406
-
* for 3700
HARD INSIDE SOLID JAWS - SETS 1)
Chuck size
mm
80
100
110
125
140
160
200
250
315
400
500
630
800
Code No 0642
Code No 0642
Code No 0642
Code No 0642
For chuck
type 3200, 3500
3-jaw set
985 351 000
985 351 101
985 352 408
985 351 203
985 352 703
985 351 305
985 351 407
985 351 509
985 351 600
985 351 702
985 351 804
985 351 906
985 352 102
For chuck
type 3600, 3700
4-jaw set
985 381 982 *
985 391 909
985 391 206
985 392 003
985 391 308
985 391 400
985 391 501
985 391 603
985 391 705
985 391 807
985 391 810
-
For chuck
type 3864
6-jaw set
985 401 200
985 401 301
985 401 403
985 401 505
985 401 607
985 401 709
985 401 800
985 351 975
-
For chuck
type 3266
3-jaw set
985 351 025
985 351 127
985 351 229
985 351 305
985 351 407
-
* for 3700
SOFT SOLID JAWS - SETS
Chuck size
mm
80
100
110
125
140
160
200
250
315
400
500
630
800
Code No 0642
Code No 0642
Code No 0642
For chuck
type 3200, 3500
3-jaw set
985 360 007
985 360 109
985 352 500
985 360 200
985 352 805
985 360 302
985 360 404
985 360 506
985 360 608
985 360 700
985 360 801
985 360 903
985 360 929
For chuck
type 3600, 3700
4-jaw set
985 398 100 *
985 398 009
985 398 202
985 397 904
985 398 304
985 398 406
985 398 508
985 398 600
985 398 701
985 398 803
985 398 905
-
For chuck
type 3864
6-jaw set
985 402 200
985 402 302
985 402 404
985 402 506
985 402 608
985 402 700
985 402 801
985 402 903
-
* for 3700
HARD 2-PIECE REVERSIBLE JAWS - SETS 1)
Chuck size
mm
125
160
200
250
315
400
500
630
800
Code No 0642
Code No 0642
Code No 0642
For chuck
type 3200, 3500
3-jaw set
985 353 205
985 353 307
985 353 409
985 353 500
985 353 602
985 353 704
985 353 806
985 353 908
985 354 002
For chuck
type 3600, 3700
4-jaw set
985 392 207
985 392 309
985 392 400
985 392 502
985 392 604
985 392 706
985 392 808
985 392 900
-
For chuck
type 3865
6-jaw set
985 403 201
985 403 303
985 403 405
985 403 507
985 403 609
985 403 700
985 403 802
985 403 904
-
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
55
SPARE PARTS FOR SELF-CENTERING LATHE CHUCKS
HARD TOP JAWS - SETS
Chuck size
mm
125
160
200
250
315
400
500
630
800
1)
Code No 0642
Code No 0642
Code No 0642
For chuck
type 3200, 3500
For chuck
type 3600, 3700
For chuck
type 3865
3-jaw set
985 328 205
985 328 307
985 328 409
985 328 500
985 328 602
985 328 704
985 328 806
985 328 908
985 328 908
4-jaw set
985 378 206
985 378 308
985 378 400
985 378 501
985 378 603
985 378 705
985 378 807
985 378 909
-
6-jaw set
985 408 206
985 408 308
985 408 400
985 408 501
985 408 603
985 408 705
985 408 807
985 408 909
-
HARD MASTER JAWS - SETS
Code No 0642
Chuck size
mm
125
160
200
250
315
400
500
630*
800
For chuck
type 3100
Code No 0642
1)
Code No 0642
Code No 0642
Code No 0642
For chuck
type 3865
For chuck
type 3295
6-jaw set
985 409 207
985 409 309
985 409 400
985 409 502
985 409 604
985 409 706
985 409 808
985 409 900
-
3-jaw set
985 399 860
985 399 873
985 399 886
-
For chuck
For chuck
type 3200, 3500 type 3600, 3700
2-jaw set
985 307 106
985 307 208
985 307 300
985 307 401
985 307 900
-
3-jaw set
985 357 209
985 357 300
985 357 402
985 357 504
985 357 606
985 357 708
985 357 800
985 357 901
985 358 006
4-jaw set
985 396 200
985 396 302
985 396 404
985 396 506
985 396 608
985 396 700
985 396 801
985 396 814
-
* for 3295 - 660
SOFT 2-PIECE JAWS - SETS
Chuck size
mm
125
160
200
250
315
400
500
630
800
Code No 0642
Code No 0642
Code No 0642
Code No 0642
For chuck
type 3100
For chuck
type 3200, 3500
For chuck
type 3600, 3700
For chuck
type 3865
2-jaw set
985 300 100
985 300 201
985 300 303
985 300 405
985 301 100
-
3-jaw set
985 355 207
985 355 309
985 355 400
985 355 502
985 355 604
985 355 706
985 355 808
985 355 900
985 356 004
4-jaw set
985 394 209
985 394 300
985 394 402
985 394 504
985 394 606
985 394 708
985 394 800
985 394 901
-
6-jaw set
985 405 216
985 405 318
985 405 410
985 405 511
985 405 613
985 405 715
985 405 804
985 356 017
-
Type 3865
SOFT TOP JAWS - SETS
Chuck size
mm
125
160
200
250
315
400
500
630
800
Code No 0642
Code No 0642
Code No 0642
Code No 0642
For chuck
type 3100
For chuck
type 3200, 3500
For chuck
type 3600, 3700
For chuck
type 3865
2-jaw set
985 305 308
985 305 400
985 305 501
985 305 603
985 305 705
-
3-jaw set
985 330 206
985 330 308
985 330 400
985 330 501
985 330 603
985 330 705
985 330 807
985 330 909
985 330 909
4-jaw set
985 382 209
985 382 300
985 382 402
985 382 504
985 382 606
985 382 708
985 382 800
985 382 901
-
6-jaw set
985 407 220
985 407 322
985 407 424
985 407 526
985 407 628
985 407 720
985 407 806 *
985 407 908 *
-
* not bevelled
Hard jaws, supplied as supplement or as spares, must be ground on the chuck, otherwise centering accuracy does not
conform to the limits. This job can be done in the BISON plant at an extra charge. In case of a subsequent jaw delivery
please return the chuck.
1)
http://www.bison-bial.com, e-mail:[email protected] tel.+48 857 416 420
56
SPARE PARTS FOR SELF-CENTERING LATHE CHUCKS
STUD BOLT
Chuck size
Code No 0642
mm
For chuck type 3100, 3200,
3600, 4500, 4600,4700,4800
80
100
125
160
200
250
985 335 109
985 335 109
985 335 200
985 335 200
985 335 404
985 335 404
Chuck size
Code No 0642
mm
inch
For chuck type 3100, 3200,
3600, 4500, 4600, 4700, 4800
315
400
500
630
800
12 1/2
15 3/4
20
25
31 1/2
985 335 404
985 335 700
985 335 700
985 335 700
985 335 700
PINION
Chuck size
Code No 0642
Code No 0642
Code No 0642
mm
For chuck type 3100, 3200,
3600, 4500, 4600, 4700, 4800
For chuck type 3500, 3700, 3800
For chuck type 3295
80
100
110
125
140
160
200
250
315
400
500
630*
800
985 334 006
985 334 108
985 333 800
985 334 200
985 333 901
985 334 301
985 334 403
985 334 505
985 334 607
985 334 709
985 334 800
985 334 902
985 335 007
985 334 006
985 334 108
985 362 202
985 362 304
985 362 406
985 362 508
985 362 600
985 362 701
985 362 803
985 362 905
-
985 399 613
985 399 626
985 399 639
-
* for 3295 - 660
SCROLL PLATE
Chuck size
Code No 0642
Code No 0642
Code No 0642
mm
For chuck type 3100, 3200,
3600, 4500, 4600, 4700, 4800
For chuck type 3500, 3700, 3800
For chuck type 3295
80
100
110
125
140
160
200
250
315
400
500
630*
800
985 361 008
985 361 100
985 366 705
985 367 207
985 366 807
985 367 309
985 367 400
985 367 502
985 367 604
985 367 706
985 367 808
985 367 900
985 367 003
985 361 010
985 361 112
985 361 201
985 361 303
985 361 405
985 361 507
985 361 609
985 361 700
985 361 726
985 361 741
-
985 399 715
985 399 728
985 399 730
-
SAFETY WRENCH
LOCKING HALF-RING
SLEEVE BEARING
Chuck size
Code No 0642
Code No 0642
Code No 0642
mm
For chuck type 3100, 3200,
3500, 3600, 3700, 3800
For chuck type 3500, 3700,
3800
For chuck type 3500, 3700,
3800
80
85
100
110
125
140
160
200
250
315
400
500
630
800
985 340 102
985 340 102
985 340 204
985 340 204
985 340 204
985 340 306
985 340 306
985 340 306
985 340 408
985 340 408
985 340 500
985 340 601
985 340 601
985 340 703
985 363 203
985 363 305
985 363 407
985 363 509
985 363 600
985 363 702
985 363 804
985 363 906
-
985 364 204
985 364 306
985 364 408
985 364 500
985 364 601
985 364 703
985 364 805
985 364 907
-
* for 3295 - 660
Safety
wrench
Locking half-ring
Sleeve bearing
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
57
SPARE PARTS FOR SELF-CENTERING LATHE CHUCKS
ADJUSTING SPINDLE
Chuck size
mm
200
250
315
400
500
630
Code No 0642
For chuck type 4500, 4600, 4700, 4800
985 751 100
985 751 202
985 751 304
985 755 104
985 755 206
985 755 308
HARD MASTER JAW - SETS
Chuck size
Code No 0642
Code No 0642
For chuck type 4500, 4700
For chuck type 4600, 4800
3-jaw set
985 752 305
985 752 407
985 752 509
985 756 502
985 756 604
985 756 706
4-jaw set
985 753 408
985 753 500
985 753 601
985 758 107
985 758 209
985 758 300
mm
200
250
315
400
500
630
HARD SOLID REVERSIBLE JAW - SETS
Chuck size
Code No 0642
Code No 0642
For chuck type 4500, 4700
For chuck type 4600, 4800
3-jaw set
985 751 508
985 751 600
985 751 701
985 755 501
985 755 603
985 755 705
4-jaw set
985 752 600
985 752 702
985 752 804
985 757 106
985 757 208
985 757 300
mm
200
250
315
400
500
630
SOFT SOLID JAW - SETS
Chuck size
Code No 0642
Code No 0642
For chuck type 4500, 4700
For chuck type 4600, 4800
3-jaw set
985 751 905
985 752 000
985 752 101
985 756 105
985 756 207
985 756 309
4-jaw set
985 753 000
985 753 102
985 753 204
985 757 503
985 757 605
985 757 707
mm
200
250
315
400
500
630
MOUNTING BOLTS FOR LATHE CHUCKS TYPE 3100, 3200, 3500, 3600, 3700, 4300
AND FOR ADAPTER PLATES TYPE 8200
STUD AND LOCKNUT - DIN 55027
Size
M10x34
M10x39
M10x43
M12x50
M16x60
M20x75
M24x90
Taper size 1 : 4
3
4
5
6
8
11
15
pcs/set
3
3
4
4
4
6
6
Code No 0642 1)
985 821 103
985 821 205
985 821 307
985 821 409
985 821 500
985 821 602
985 821 704
STUD FOR CAMLOCK - DIN 55029
Size
M10x1-35
M10x1-37
M12x1-43
M16x1,5-49
M20x1,5-55,5
M22x1,5-67
M24x1,5-76
M27x2-89
1)
Tuleja
Taper size 1 : 4
3
4
5
6
8
11
15
20
pcs/set
3
3
6
6
6
6
6
6
for one piece
Example of order: Stud for DIN 55027 M12x50
http://www.bison-bial.com, e-mail:[email protected] tel.+48 857 416 420
58
Code No 0642 1)
985 825 107
985 825 209
985 825 300
985 825 402
985 825 504
985 825 606
985 825 708
985 825 800
MAIN DIMENSIONS OF HARD SOLID JAWS AND SOFT
SOLID JAWS FOR CHUCKS TYPE 3200, 3500, 3700, 3864
Chuck size
80
85
100
110
125
140
160
A
B
C
D
E
F
G
H
J
K
32
11
28
6
6
6
9,5
21
9,5
21
0,03
0,07
43
11
28
6
6
6
10
26
12
26
0,07
-
42
15
32
6
6
7
11
27
12
27,5
0,09
0,13
42
15
32
6
6
7
11
27
12
27,5
0,09
0,13
51
20
40
8
8
8
13
33,5
13
33,5
0,18
0,26
51
20
40
8
8
8
13
33,5
13
33,5
0,18
0,26
70
20
53
8
8
10
19
45
22
47,5
0,36
0,50
Chuck size
200
250
315
400
500
630
800
A
B
C
D
E
F
G
H
J
K
85
25
54
9
10
12
23
57
23
57
0,50
0,80
105
28
63
11
12
14
28
69,5
28
69,5
0,80
1,36
125
32
73
12,7
12
18
34,5
83
34,5
83
1,32
1,90
145
36
92
15
14
22
36
99
36
99
2,35
2,46
180
40
100
16
14
26
50
119,5
50
119,5
3,36
5,00
225
50
110
16
14
28
66
149
66
149
5,80
8,36
225
50
110
16
14
28
66
149
66
149
5,80
8,36
Hard solid inside
and outside jaws
Soft solid jaws
Dimensions G and H apply to outside jaws
Dimensions J and K apply to inside jaws
hard jaws
soft jaws
Approx. weight
(kg)
Approx. weight
(kg)
hard jaws
soft jaws
MOUNTING DIMENSIONS OF HARD MASTER JAWS
FOR CHUCKS TYPE 3100, 3200, 3500, 3600, 3700, 3865
ø125 - 250
ø315 - 400
ø500
ø630 - 800
Chuck size
125
140
160
200
250
315
A
B
C
D
E
F - 0,03
G + 0,01
H
J
K
L
M
S
Approx. weight
(kg)
54
20
28
8
8
7,94
12,69
22,6
4
16
13,5
65
20
29
8
8
7,94
12,69
28,6
4
19,05
14
79
25
33
9
10
7,94
12,69
34,9
4
22,25
14
3,2
54
20
28
8
8
7,94
12,69
22,6
4
16
13,5
M8
3,2
110
32
40
12,7
12
12,7
19,4
47,6
4
31,75
16
M12
3,2
0,14
0,14
M8
M6*
3,2
3,2
92
28
36
11
12
12,7
19,04
39,7
4
27
16
M12
3,2
0,18
0,30
0,48
0,77
M10
M8*
M10
M8*
Chuck size
400
500
630
800
915
1000
A
B
C
D
E
F - 0,03
G + 0,01
H
J
K
L
M
S
Approx. weight
(kg)
130
36
49
15
14
12,7
19,04
57,1
7,2
38,1
22
M16
3,2
166
40
54
16
14
12,7
19,04
57,1
7,2
38,1
32,5
M20
3,2
210
50
54,5
16
14
12,7
19,04
57,1
7,2
38,1
32,5
M20
3,2
225
50
54,5
16
14
12,7
19,04
57,1
7,2
38,1
32,5
M20
3,2
283
70
64
22
20
12,7
19,04
57,1
7,2
38,1
36
M22
3,2
328
70
64
22
20
12,7
19,04
57,1
7,2
38,1
36
M22
3,2
1,10
2,18
3,34
3,4
6,65
7,7
* for 3865
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
59
MOUNTING DIMENSIONS OF TOP JAWS
FOR CHUCKS 3100, 3200, 3500, 3600, 3700, 3865
Chuck size
Hard top jaws
A
A1
B
B do 3100
C
D
E
F
G
H
H1
J
K
L
L1
M
N
O
P
R
R1
hard jaws
Approx.
weight
soft jaws
(kg)
125
56
64
22
38,5
7,95
4
3,2
12,69
22,6
25
9
6,6**
15
11**
10
26
16
8
14,5
35
13
15
0,17
140
160
200
250
315
56
64
22
38,5
7,95
4
3,2
12,69
22,6
25
9
15
10
26
16
8
14,5
35
13
15
0,17
67
78
25
40
41,5
7,95
4
3,2
12,69
28,6
34
80
90
27
40
110
120
37
52
55
12,71
4
3,2
19,04
47,6
53
14
20
14,5
40
31,75
13
26,5
68
35,4
30,7
0,90
1,60
12
29
19,05
8,5
18
41,5
16
21
0,26
12
31
22,25
9,5
21,5
51
19
24
0,36
95
106
32,5
47
51,5
12,71
4
3,2
19,04
39,7
45
14
20
14,5
38
27
12
24,5
59
22
27,5
0,62
0,65
1,15
11
18
9**
14**
41,5*
43,5
7,95
4
3,2
12,69
34,9
40
11
18
9**
14**
0,30
0,30
0,46
Chuck size
400
500
630
800
915
1000
A
A1
B
B do 3100
C
D
E
F
G
H
H1
J
K
L
L1
M
N
O
P
R
R1
hard jaws
Approx.
weight
soft jaws
(kg)
127
140
42
52
64,5
12,71
4
6,3
19,04
57,1
63
18
26
18,5
45,5
38,1
13,5
27
76,5
28,5
34,4
1,35
127
140
42
74,5
12,71
41
6,3
19,04
57,1
63
22
33
21
56
38,1
17
50
88
28,5
34,4
1,55
127
160
52
82
12,71
4
6,3
19,04
57,1
63
22
33
21
64
38,1
21
51
89
28,5
34,4
2,42
127
160
52
82
12,71
4
6,3
19,04
57,1
63
22
33
21
64
38,1
21
51
89
28,5
34,4
2,42
175
190
75
97
12,71
4,5
6,3
19,04
95,2
105
24
35
23
78
38,1
28
48
124
67
76,5
5,5
175
190
75
97
12,71
4,5
6,3
19,04
95,2
105
24
35
23
78
38,1
28
48
124
67
76,5
5,5
2,20
2,40
4,20
4,20
-
-
* for 3100 ** for 3865
Soft top jaws
MOUNT ING BOLTS FOR TOP JAWS
Chuck size
mm
125
140
160
200
250
315
400
500
630
800
bolt 1
M8x25
M8x25
M10x30
M10x30
bolt 2
M6x30*
M8x30*
M8x30*
M8x20
M8x20
M10x20
M10x20
M12x40
M12x40
M16x45
M20x75
M20x80
M20x80
* for 3865
http://www.bison-bial.com, e-mail:[email protected] tel.+48 857 416 420
60
M6x20*
M8x20*
M8x20*
M12x25
M12x25
M16x30
M20x40
M20x40
M20x40
3 JAW CHUCKS WITH MORSE TAPER
Type 9154, 9155, 9156, 9164, 9165,
9184, 9185, 9186, 9187, 4956
Features
■■ 3 jaw chuck with morse taper
■■ Able to work in horizontal and vertical positions
■■ Able to divide and block workpiece during machining (type 9184
and type 9185)
■■ Able to block workpiece during machining (type 9186 and type
9187)
Application
■■ Designed for simultaneously supporting and clamping long objects
(tubes, shaft etc.) during turning, milling and grinding operations
■■ Can replace typical center in machine tailstock
ROTATING - type 9154, 9155
D
SM
A
B
min -1
80
80
100
100
125
125
160
2
3
3
4
4
5
5
102,5
102,5
111,5
113,0
127,0
127,0
149,5
110
4000
Approx. weight
(kg)
3,5
3,8
5,5
5,9
7,9
8,6
14,3
3500
3200
3000
Type 9154, 9156
Type 9155
Standard
accessories
DEAD - type 9156
D
SM
A
80
80
100
125
125
160
160
2
3
3
4
5
4
5
65,5
62,5
68,5
85,0
105,0
93,5
93,5
Approx. weight (kg)
min -1
2,2
2,3
3,7
6,7
7,0
14,9
15,2
4000
3500
3200
3000
1 chuck 3274
1 set of outside
hard solid jaws
1 set of inside
hard solid jaws
1 wrench
1 chuck 3275
1 set of hard top
jaws
1 set of hard
master jaws
1 wrench
D
B
E
80
100
125
160
44
50
56
64,5
16
20
32
42
C
Solid jaws
2-piece reversible jaws
13
17
20
32
40
43
d1 min
d2 max
2
3
3
3
71
83
125
160
ROTATING WITH FINE ADJUSTMENT CHUCKS - type 9164, 9165
D
SM
A
min -1
Approx. weight (kg)
100
100
125
125
160
3
4
4
5
5
151
154,5
155,5
160,5
156,5
2500
2500
2000
2000
1800
6,8
7,1
9,2
10,3
32,4
Type 9164
Type 9165
Standard
accessories
Example of order: 9164 - 100/3 AE
1 chuck 3564
1 set of outside
hard solid jaws
1 set of inside
hard solid jaws
1 wrench
1 chuck 3565
1 set of hard top
jaws
1 set of hard
master jaws
1 wrench
D
B
E
100
125
160
68
71,5
68,6
20
35
42
C
Solid jaws
17
20
32
2-piece reversible
jaws
40
43
d1 min
d2 max
3
3
3
83
125
160
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
61
3 JAW CHUCKS WITH MORSE TAPER
ROTATING DIVIDING WITH BLOCKING - Type 9184, 9185
Basic indexing:
2, 3, 4, 6, 8, 12, 24
D
SM
A
B
min -1
Approx. weight
(kg)
80
80
100
100
125
125
160
160
2
3
3
4
4
5
4
5
113,9
113,9
123,4
124,9
139,5
139,5
148
148
125
125
3000
3,9
4,1
6,2
6,5
11,0
12,0
18,0
19,0
2500
2000
1800
ROTATING WITH BLOCKING - Type 9186, 9187
D
SM
A
B
min -1
Approx. weight
(kg)
80
80
100
100
125
125
160
160
2
3
3
4
4
5
4
5
109
109
118,5
120
138,5
138,5
147
147
125
125
3200
3200
2800
2800
2500
2500
2200
2200
3,6
3,8
6,0
6,0
11,0
12,0
18,0
18,9
Type 9184, 9186
Type 9185, 9187
Standard
accessories
Example of order: 9186 - 80/2
1 chuck 3274
1 set of outside
hard solid jaws
1 set of inside
hard solid jaws
1 wrench
1 chuck 3275
1 set of hard top
jaws
1 set of hard
master jaws
1 wrench
C
D
B
E
80
100
125
160
44
50
56
64,5
16
20
32
42
Solid jaws
2-piece reversible jaws
13
17
20
32
40
43
d1 min
d2 max
2
3
3
3
71
83
125
160
4 JAW INDEPENDENT CHUCKS WITH MORSE TAPER
ROTATING - Type 4954
D
SM
A
B
min -1
Approx. weight
(kg)
100
125
160
160
4 AE
4 AE
4 AE
5 AE
115
135,5
135,5
135,5
98
115
115
115
3500
3200
2800
2800
6,0
8,0
11,2
12,0
DEAD - Type 4954
D
SM
125
4 AE
A
min -1
Approx. weight (kg)
72
3200
6,0
Example of order: 4954-125/4AE
D
B
C
E
d1 min
d2 max
100
40
17
25
3
100
125
43
20
26
8
125
160
43
20
42
8
160
http://www.bison-bial.com, e-mail:[email protected] tel.+48 857 416 420
62
SELF-CENTERING AND INDIVIDUALLY
ADJUSTABLE SCROLL CHUCKS
Type 4505, 4605, 4705, 4805
Features
■■ Combines features of both self-centering and individually adjustable
scroll chucks: user can adjust chuck once and the self-centering option
assures repeatability throughout the rest of the batch
■■ 4 jawed chuck (type 4605 and type 4805) is able to machine both
square and round workpieces, granting greater flexibility
■■ Steel body (type 4705 and type 4805) extends machine life while
providing higher rigidity and greater wear resistance, enabling the
chuck to withstand higher machining forces
Application
■■ Particularly suitable for lining up and chucking workpieces of irregular
shape
3-jaw chucks
4-jaw chucks
Steel body
Cast iron body
Steel body
Type 4505
Type 4705
Type 4605
Type 4805
Standard
accessories
Cast iron body
Type 4505,
4605, 4705,
4805
1 set of hard solid
jaws
1 wrench
Spare parts - see pages 57-58
DIN 6351
Chuck size A
B
C
D H6
E
F
G
H
200
250
315
400
500
630
96
102
117
123
145
160
5,5
6
6
6,3
8
10
160
200
260
330
420
545
55
76
103
136
190
252
176
224
286
362
458
586
6xM10
6xM12
6xM16
6xM16
6xM16
6xM16
127
135
158,5
182
206
232
Gripping ranges
Chuck size A
200
250
315
400
500
630
d1 min
d2 max
4
5
10
15
20
30
200
250
315
400
500
630
Approx. weight (kg)
18,5
31
54,5
88
150
245
MAIN DIMENSIONS OF HARD SOLID AND SOFT SOLID JAWS
Soft solid jaws
Chuck size
200
250
315
400
500
630
A
B
C
D
E
F
Tr left-hand
H1
H
Approx. weight
(kg)
85
25
58
11
10
12
Tr 18 x 2
25
56
91
28
61
10
10
14
Tr 18 x 2
26,5
60
125
32
73
13,5
12
18
Tr 24 x 3
27
76
145
36
90
12
14
22
Tr 24 x 3
35
98,2
180
40
100
15
14
26
Tr 26 x 3
49,7
119,3
225
50
108
14
14
28
Tr 26 x 3
65
148
0,55
0,76
1,60
1,80
3,85
4,50
Hard solid jaws
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
63
SELF-CENTERING CHUCKS WITH LARGE THROUGH HOLE
FOR PIPE MACHINING
Type 3295
3 JAWS, CAST IRON BODY
h
k
c
a
k
b
.
M
W°
.
.
d
E
A
D
F
F1
.
W1°
C
.
M1
.
L
B
Features
■■ Cast iron body
■■ Chucks may work individually or in pairs, mounted on opposite
sides of the lathe spindle, ensuring the same vertical position
of the jaws in both chucks
■■ Large through hole compared to the outside diameter of the
chuck body
400
500
660
800
A
B
C
D
E
F
F1
M
M1
W
W1
L
a
b
c
h
400
105
6
362
220
381
6xM12
30°
120
M16
19,04
12,7
168
288
500
57,7
508
120
8
462
320
481,5
6xM16
30°
120
M20
19,04
12,7
250
380
350
75,8
660
135
14
580
406
620
6xM16
30°
127
M20
19,04
12,7
376
497
250
128,9
800
151
7
710
410
460
6xM24
30°
25
225
M20
19,04
12,7
260
566
200
212,0
Standard
accessories
Max speed
Approx. weight (kg)
min
max
min -1
kg
1 set of soft
top jaws
1 set of hard
master jaws
1 wrench
Optional
accessories
Chuck size
d
Type 3295
■■ High gripping force
■■ Able to machine very long workpieces
■■ High machining accuracy
Application
■■ Designed for clamping long pipes during machining for
conventional and specialized machine-tools
Spare parts - see pages 56-57
Example of order: 3295 - 400
http://www.bison-bial.com, e-mail:[email protected] tel.+48 857 416 420
64
1 set of hard
top jaws
SELF-CENTERING CHUCKS WITH LARGE THROUGH HOLE
FOR PIPE MACHINING
Type 3597
3 JAW, STEEL BODY (DIN 6350)
M
F
F1
D
E
A
J
C
B
M1
Features
■■ Steel body extends machine life while providing higher rigidity
and greater wear resistance, enabling the chuck to withstand
higher machining forces
■■ Chucks may work individually or in pairs, mounted on opposite
sides of the lathe spindle, ensuring the same vertical position
of the jaws in both chucks
■■ Large through hole compared to the outside diameter of the
chuck body
■■ High gripping force
■■ Able to machine very long workpieces
■■ High machining accuracy
■■ Heavy-duty components
Application
■■ This first class chuck, with increased clamping accuracy, is
designed for clamping long pipes during heavy-duty machining
for conventional and specialized machine-tools
Chuck size
315
405
515
660
800*
A
B
C
D
E
F
F1
J
M
M1
315
97
5
260
145
286
286
56,9
3x M16x30
3x M16x100
40 - 140
2500
47
405
110
5
330
220
362
381
67
6x M16x40
6x M12x120
138-406
1000
73
515
120
5
420
320
458
481,5
79
6x M16x40
6x M16x130
264 - 516
800
120
660
140
7
545
406
586
620
87
6x M16x40
6x M16x150
349 - 630
600
230
800
150
7
710
460
760
760
6x M20x50
6x M20x160
260 - 460
700
398
Gripping range
Max speed
Approx. weight (kg)
mm
min -1
kg
Type 3597
Standard
accessories
*plain back mounting
1 set of hard master jaws
1 set of hard
top jaws
1 wrench
Example of order: 3597 - 315
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
65
SELF-CENTERING CHUCKS WITH LARGE THROUGH HOLE
FOR PIPE MACHINING
Type 3515 HD
3 JAW PRECISION, STEEL BODY (DIN 55026)
I
C
H
M
L
Features
■■ Steel body extends machine life while providing higher rigidity and
greater wear resistance, enabling the chuck to withstand higher
machining forces
■■ Chucks may work individually or in pairs, mounted on opposite sides
of the lathe spindle, ensuring the same vertical position of the jaws in
both chucks
■■ Large through hole compared to the outside diameter of the chuck
body
■■ High gripping force
■■ Able to machine very long workpieces
■■ High machining accuracy
Application
■■ This first class chuck, with increased clamping accuracy, is designed for
clamping long pipes during heavy-duty machining for conventional and
specialized machine-tools
O
R
P
N
15,1/4"- 64,0" HD
Chuck size
Type 3515 HD
Standard
accessories
Short taper
A
B
C
D
E
F
H
H1
I
L
M
N
O
P
R
Gripping range
Gripping force
Max speed
Approx. weight (kg)
mm
mm
daN
min -1
kg
H1
E
F
D
A
B
15,1/4"- 85,3" HD
6
8
400
400
111
111
87
87
133,4
171,4
103
136
106,375
139,719
135
135
6x1/2"-13x4,1/2" 6x5/8"-11x4,1/2"
50
50
54
54
14H10
14H10
21
21
23
23
10
10
25 - 400
25 -400
6200
6200
1400
1400
102,11
98,32
15,3/4"- 115,0" HD
20"- 117,5" HD
25"- 1510,75" HD
25"- 2012,5" HD
31,1/2"15- 10,75" HD
31,1/2"- 2012,5" HD
11
400
111
87
165,1
130
196,869
135
6x3/4"-10x4"
50
54
14H10
21
23
10
25 -400
6200
1400
96,22
11
500
119
87
235
192
196,869
135
169
6x3/4"-10x5"
50
54
14H10
21
23
10
45 - 500
7700
1000
156,46
15
630
144
92,5
330,2
275
285,775
135
210
6x7/8"-9x6"
70
75
22H10
33
37
16
80 - 630
8200
850
278,2
20
630
144
92,5
368,3
320
412,775
135
210
6x1"-8x5"
70
75
22H10
33
37
16
160 - 630
8200
850
251,48
15
800
150
92,5
330,2
275
285,775
135
225
6x7/8"-9x6"
70
75
22H10
33
37
16
130 - 800
9000
600
502,2
20
800
150
92,5
463,5
320
412,775
135
225
6x1"-8x5"
70
75
22H10
33
37
16
180 - 800
9000
600
489,00
1 set of hard master jaws
1 set of hard
top jaws
Example of order: 3515 - 15.1/4"- 6- 4.0" HD
http://www.bison-bial.com, e-mail:[email protected] tel.+48 857 416 420
66
1 wrench
INDEPENDENT CHUCKS WITH LARGE THROUGH HOLE
FOR PIPE MACHINING
Type 4307 HD
25
+0,5
4 JAWS, STEEL BODY
91± 0,1
H
I
Ø 25 H8
135
284
E
L
C
230
8 x M16
N
E
A
B
Ø 480
D
3xM12
E
10
G
C-C
D
.
K
Ø 30
E-E
Type 4307 HD
Standard
accessories
Gripping range
Torque on wrench
Gripping force per jaw
Max speed
Approx. weight (kg)
Ø 320
F
.
Features
■■ Steel body extends machine life while providing higher rigidity and
greater wear resistance, enabling the chuck to withstand higher
machining forces
■■ Chucks may work individually or in pairs, mounted on opposite sides
of the lathe spindle, ensuring the same vertical position of the jaws in
both chucks
■■ Large through hole compared to the outside diameter of the chuck
body
■■ High gripping force
■■ Able to machine very long workpieces
■■ High machining accuracy
Application
■■ This first class chuck, with increased clamping accuracy, is designed for
clamping long pipes during heavy-duty machining for conventional and
specialized machine-tools
Chuck size
4307-1000/520-200 HD
4307-1250/520-200 HD
A
B
C
D
E
F
G
H
I
K
L
N
1000
520
200
463,6
8 x M24
31
175
187,1
90,7
28
75
22
50 - 1000
500
5000
430
985
1250
520
200
463,6
8 x M24
31
175
187,1
90,7
28
75
22
50 - 1250
500
5000
350
1560
mm
Nm
daN
min -1
kg
1 set of hard sectional jaws
(master+hard top reversible)
1 wrench
Example of order: 4307- 1000/520-200 HD
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
67
INDEPENDENT CHUCKS WITH LARGE THROUGH HOLE
FOR PIPE MACHINING
Type 4317 HD
4 JAWS, STEEL BODY (DIN 55026)
I
L
C
B
.
E
A
D
N
.
7° 7
'30"
H
F
K
.
G
Chuck size
Short taper 1:4
A
B
C
D
E
F
G
H
I
K
L
N
Gripping range
Torque on wrench
Gripping force per jaw
Max speed
Approx. weight (kg)
mm
mm
Nm
daN
min -1
kg
Chuck size
Short taper 1:4
A
B
C
D
E
F
G
H
I
K
L
N
Gripping range
Torque on wrench
Gripping force per jaw
Max speed
Approx. weight (kg)
mm
mm
Nm
daN
min -1
kg
16"- 85.3" HD
16"- 116.5" HD
20"- 116.5" HD
20"- 158" HD
25"- 1510.5" HD
25"- 2010.5" HD
25"- 2012.5" HD
8
415
139,719
136
171,4
4 x M16x110
21,3
145
154,1
75,7
18
62
19
45-415
350
3200
1200
145
11
415
196,869
168
235,0
4 x M20x110
25,3
145
154,1
75,7
18
62
19
45-415
350
3200
1200
137
11
500
196,869
168
235,0
8 x M20x110
25,4
145
154,1
75,7
22
60
19
45-500
350
3200
1000
204
15
500
285,775
205
330,2
8 x M24x150
31,4
145
154,1
75,7
22
60
19
45-500
350
3200
1000
188
15
630
285,775
270
330,2
8 x M24x160
34,1
155
167,1
90,7
22
75
22
50 - 630
400
3700
850
310
20
630
412,775
270
463,6
8 x M24x160
38,1
155
167,1
90,7
22
75
22
50 - 630
400
3700
850
295
20
630
412,775
320
463,6
8 x M24x160
38,1
155
167,1
90,7
22
75
22
100 - 630
400
3700
850
300
28"- 1510.5" HD
28"- 2012.5" HD
31.1/2"- 1510.5" HD
31.1/2"- 2012.5" HD
31.1/2"- 2014.5" HD
40"- 2820.5" HD
49"- 1511" HD
15
710
285,775
270
330,2
8 x M24x160
34,1
155
167,1
90,7
22
75
22
75 - 710
450
4100
750
415
20
710
412,775
320
463,6
8 x M24x160
38,1
155
167,1
90,7
22
75
22
100 - 710
450
4100
750
395
15
800
285,775
270
330,2
8 x M24x160
34,1
165
177,1
90,7
22
75
22
75 - 800
450
4100
600
585
20
800
412,775
320
463,6
8 x M24x160
38,1
165
177,1
90,7
22
75
22
115 - 800
450
4100
600
565
20
800
412,775
370
463,6
8 x M24x160
38,1
165
177,1
90,7
22
75
22
155 - 800
450
4100
600
545
28
1000
584,225
530
647,6
8 x M30x180
38,8
175
187,1
90,7
28
75
22
350 - 1000
500
4500
430
765
15
1250
285,775
281
330,2
8 x M24x180
28,8
175
187,1
90,7
28
75
22
100 - 1250
500
5000
350
1606
Type 4317 HD
Standard
accessories
Example of order: 4317-28"- 15- 10.5" HD
1 set of hard sectional jaws
(master+hard top reversible)
1 wrench
Example of order: 4317 - 28"- 15- 10.5" HD
http://www.bison-bial.com, e-mail:[email protected] tel.+48 857 416 420
68
INDEPENDENT CHUCKS WITH LARGE THROUGH HOLE
FOR PIPE MACHINING
Type 4347 HD
4 JAWS, STEEL BODY (DIN 55029)
H
I
.
.
.
.
.
N
L
C
E
.
.
A
D
B
.
.
7°7
'30
"
.
.
F
K
G
Features
■■ Steel body extends machine life while providing higher rigidity
and greater wear resistance, enabling the chuck to withstand
higher machining forces
■■ Chucks may work individually or in pairs, mounted on opposite
sides of the lathe spindle, ensuring the same vertical position
of the jaws in both chucks
■■ Large through hole compared to the outside diameter of the
chuck body
Chuck size
Type 4347 HD
Standard
accessories
Short taper
A
B
C
D
E
F
G
H
I
K
L
N
Gripping range
Torque on wrench
Gripping force per jaw
Max speed
Approx. weight (kg)
mm
mm
Nm
daN
min -1
kg
■■ High gripping force
■■ Able to machine very long workpieces
■■ High machining accuracy
Application
■■ This first class chuck, with increased clamping accuracy, is
designed for clamping long pipes during heavy-duty machining
for conventional and specialized machine-tools
16"- 8- 5,3" HD
16"- 11- 6,5" HD
20"- 8- 5,3" HD
20"- 11- 6,5" HD
28"- 11- 7,5" HD
8
415
139,719
136
171,4
25,4
50,7
145
154,1
75,7
18
60
19
45 - 400
350
3200
1200
136
11
415
196,869
168
235
30,2
60,6
145
154,1
75,7
18
60
19
45 - 400
350
3200
1200
128
8
500
139,719
136
171,4
25,4
50,7
145
154,1
75,7
22
60
19
45 - 500
350
3200
1000
212
11
500
196,869
168
235
30,2
60,6
145
154,1
75,7
22
60
19
45 - 500
350
3200
1000
205
11
710
196,869
192
235
30,2
60,6
155
167,1
90,7
22
75
22
75 - 710
450
4100
750
450
1 set of hard sectional jaws
(master+hard top reversible)
1 wrench
Example of order: 4347 - 28"- 11 - 7.5" HD
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
69
INDEPENDENT CHUCKS
Type 4304, 4305
4 JAWS, CAST IRON BODY
Features
■■ 4 jaw, independent chuck with manual clamping, and a high quality
cast iron body
■■ Mounted on the machine-tool spindle from the back of the chuck, using
the adaptor plate
■■ Chuck bodies, in sizes up to 160 mm diameter, are made from steel
■■ Four jaws ensure the precise centering of square-shaped workpieces
with the maximum permitted gripping force
■■ Chucks with diameters of 250 mm and above are equipped with
additional T-slots, permitting the addition of extra jaws
Application
■■ Suitable for machining square and round workpieces on all types of
workshop machining operations on conventional lathes
Options
■■ Hard solid jaws (type 4304) or hard two-piece jaws (type 4305)
■■ Chuck design: our engineers can work with you to implement any
product design changes you may require
Chuck size
85
100
125
160
200
250
315
A
B
C
D H7
E
F
G
H
J
K
L
Approx. weight (kg) ca. kg
86
40
5
62
25
72
4xM6
34
17
1,9
100
40
2,5
79,38
25
54
4xM8
34
17
2,4
130
43
2,5
69,85
26
54
4xM8
51
20
3,8
156
43
2,5
82,55
42
69,85
4xM10
51
20
4,3
200
80
5
110
50
82,6
4xM10
81
40,3
82
46,4
14,0
250
85
7
150
65
104,8
4xM12
96,5
40,3
96,5
60,4
25,0
315
95
7
175
80
133,4
4xM16
111
49,8
112,5
60,9
39,0
Chuck size
350
400
500
630
800
915
1000
1250
A
B
C
D H7
E
F
G
H
J
K
L
Approx. weight (kg) ca, kg
350
95
7
175
80
133,4
4xM16
111
49,8
47,5
400
105
10
200
100
171,4
4xM16
129
49,8
129
72,3
61,0
500
120
12
270
125
235
4xM20
152,5
59,8
136
90,3
105
630
140
12
270
160
235
4xM20
177
59,8
136
97,8
163
800
160
12
380
200
330
4xM24
202
70,8
136
93,8
319
915
170
18
370
190
330
8xM24
160
102,8
350
1000
170
18
370
190
330
8xM24
160
102,8
410
1250
190
18
550
190
500
8xM24
160
102,8
950
Type 4305
1 set of solid
jaws
1 set of hard
top jaws
1 wrench
1 set of hard
master jaws
1 wrench
Optional
accessories
Type 4304
Standard
accessories
Other engineering data - see page 79
Spare parts - see page 80
Example of order: 4304 - 85
http://www.bison-bial.com, e-mail:[email protected] tel.+48 857 416 420
70
1 set of soft solid
jaws
1 set of soft
solid jaws
INDEPENDENT CHUCKS
Type 4302, 4303
4 JAWS, CAST STEEL BODY
Features
■■ 4 jaw, independent chuck with manual clamping, and a high
quality steel body
■■ Steel body extends machine life while providing higher rigidity
and greater wear resistance, enabling the chuck to withstand
higher machining forces
■■ Four jaws ensure the precise centering of square-shaped
workpieces with the maximum permitted gripping force
■■ Chucks with diameters of 250 mm and above are equipped
with additional T-slots, permitting the addition of extra jaws
■■ Mounted on the machine-tool spindle from the back of the
chuck, using the adaptor plate
Application
■■ This first class chuck, with increased clamping accuracy, is
made for all types of very high precision workshop machining
operations on conventional lathes
■■ Suitable for machining square and round workpieces
Options
■■ Hard solid jaws (type 4304) or hard two-piece jaws (type 4305)
■■ Chuck design: our engineers can work with you to implement
any product design changes you may require
Chuck size
200
250
315
400
500
A
B
C
D H7
E
F
G
H
J
L
K
Approx. weight (kg) ca. kg
200
80
5
110
50
82,6
4xM10
81
40,3
46,4
82
14,0
250
85
7
150
65
104,8
4xM12
96,5
40,3
60,4
96,5
25,0
315
95
7
175
80
133,4
4xM16
111
49,8
60,9
112,5
39,0
400
105
10
200
100
171,4
4xM16
129
49,8
72,3
129
61,0
500
120
12
270
125
235
4xM20
152,5
59,8
90,3
136
105
Chuck size
630
800
915
1000
1250
A
B
C
D H7
E
F
G
H
J
L
K
Approx. weight (kg) ca. kg
630
140
12
270
160
235
4xM20
177
59,8
97,8
136
163
800
160
12
380
200
330
4xM24
202
70,8
93,8
136
319
915
170
18
370
190
330
8xM24
102,8
160
350
1000
170
18
370
190
330
8xM24
102,8
160
410
1250
190
18
550
190
500
8xM24
102,8
160
950
Type 4303
1 set of solid
jaws
1 set of hard
top jaws
1 wrench
1 set of hard
master jaws
1 wrench
Optional
accessories
Type 4302
Standard
accessories
Other engineering data - see page 79
1 set of soft solid
jaws
1 set of soft solid
jaws
Spare parts - see page 80
Example of order: 4302 - 200
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
71
INDEPENDENT CHUCKS
Type 4314, 4315
4 JAW, CAST IRON BODY (DIN 55026)
Features
■■ 4 jaw, independent chuck with manual clamping, and a high quality
cast iron body
■■ Four jaws ensure the precise centering of square-shaped workpieces
with the maximum permitted gripping force
■■ Chucks with diameters of 250 mm and above are equipped with
additional T-slots, permitting the addition of extra jaws
■■ Mounted directly to “A” type machine-tool spindles
Application
■■ Suitable for machining square and round workpieces on all types of
workshop machining operations on conventional lathes
Options
■■ Hard solid jaws (type 4314) or hard two-piece jaws (type 4315)
■■ Chuck design: our engineers can work with you to implement any
product design changes you may require
Chuck size
Short taper 1:4
4
B
D min
63,513
D max
63,526
E
F
82,6
G
4xM10
H
J
K
L
Approx. weight (kg)
Chuck size
Short taper 1:4
B
D min
D max
E
F
G
H
J
K
L
Approx. weight (kg)
200
5
6
4
80
82,563 106,375 63,513
82,578 106,390 63,526
50
104,8
133,4
82,6
4xM10 4xM12 8xM10
81
40,3
82
46,4
17,0
8
139,719
139,734
125
171,4
8xM16
630
11
140
196,869
196,887
235
8xM20
177
59,8
136
97,8
165,0
250
315
400
500
6
8
6
8
11
6
8
11
15
85
95
105
120
82,563 106,375 139,719 82,563 106,375 139,719 106,375 139,719 196,869 106,375 139,719 196,869 285,775
82,578 106,390 139,734 82,578 106,390 139,734 106,390 139,734 196,887 106,390 139,734 196,887 285,795
65
80
100
100
125
104,8
133,4
171,4
104,8
133,4
171,4
133,4
171,7
235
133,4
171,4
235
330,2
8xM10 4xM12 4xM16 4xM10 8xM12 4xM16 8xM12 4xM16 4xM20 4xM12 8xM16 8xM20 4xM24
96,5
111
111
152,5
40,3
49,8
49,8
59,8
96,5
112,5
129
136
60,4
60,9
72,3
90,3
25,5
40,0
65
114,0
5
6
8
5
800
160
15
8
11
285,775
285,795
139,719
139,734
125
171,4
4xM16
196,869
196,887
180
235
8xM20
330,2
4xM24
160
202
70,8
136
93,8
305
1000
15
20
11
285,775
285,795
200
330,2
8xM24
412,775
412,802
200
463,6
4xM24
196,869
196,887
235
8xM20
170
190
160
102,8
395,0
1250
15
11
285,775
285,795
196,869
196,887
330,2
8xM24
235
8xM20
190
190
160
102,8
950
15
285,775
285,795
330,2
8xM24
Type 4315
1 set of solid
jaws
1 set of hard
top jaws
1 wrench
1 set of hard
master jaws
1 wrench
Optional
accessories
Type 4314
Standard
accessories
Other engineering data - see page 79
Spare parts - see page 80
Example of order: 4314-200/5
http://www.bison-bial.com, e-mail:[email protected] tel.+48 857 416 420
72
1 set of soft solid
jaws
1 set of soft solid
jaws
INDEPENDENT CHUCKS
Type 4312, 4313
4 JAWS, CAST STEEL BODY (DIN 55026)
■■ Four jaws ensure the precise centering of square-shaped
workpieces with the maximum permitted gripping force
■■ Chucks with diameters of 250 mm and above are equipped
with additional T-slots, permitting the addition of extra jaws
■■ Mounted directly to “A” type machine-tool spindles
Application
■■ This first class chuck, with increased clamping accuracy, is
made for all types of very high precision workshop machining
operations on conventional lathes
■■ Suitable for machining square and round workpieces
Options
■■ Hard solid jaws (type 4312) or hard two-piece jaws (type 4313)
■■ Chuck design: our engineers can work with you to implement
any product design changes you may require
Features
■■ 4 jaw, independent chuck with manual clamping, and a high
quality steel body
■■ Steel body extends machine life while providing higher rigidity
and greater wear resistance, enabling the chuck to withstand
higher machining forces
Chuck size
Short taper 1:4
4
B
D min
63,513
D max
63,526
E
F
82,6
G
4xM10
H
J
K
L
Approx. weight
(kg)
Chuck size
Short taper 1:4
8
B
D min
139,719
D max
139,734
E
125
F
171,4
G
8xM16
H
J
K
L
Approx. weight
(kg)
200
5
6
4
80
82,563 106,375 63,513
82,578 106,390 63,526
50
104,8
133,4
82,6
4xM10 4xM12 8xM10
81
40,3
82
46,4
250
315
400
500
6
8
6
8
11
6
8
11
15
85
95
105
120
82,563 106,375 139,719 82,563 106,375 139,719 106,375 139,719 196,869 106,375 139,719 196,869 285,775
82,578 106,390 139,734 82,578 106,390 139,734 106,390 139,734 196,887 106,390 139,734 196,887 285,795
65
80
100
100
125
104,8
133,4
171,4
104,8
133,4
171,4
133,4
171,7
235
133,4
171,4
235
330,2
8xM10 4xM12 4xM16 4xM10 8xM12 4xM16 8xM12 4xM16 4xM20 4xM12 8xM16 8xM20 4xM24
96,5
111
129
152,5
40,3
49,8
49,8
59,8
96,5
112,5
129
136
60,4
60,9
72,3
90,3
5
17,0
6
8
5
25,5
630
11
15
140
196,869 285,775
196,887 285,795
160
235
330,2
8xM20
4xM24
177
59,8
136
97,8
40,0
800
8
139,719
139,734
125
171,4
4xM16
165,0
11
65
915
15
160
196,869 285,775
196,887 285,795
180
200
235
330,2
8xM20
8xM24
202
70,8
136
93,8
20
412,775
412,802
200
463,6
4xM24
305
11
15
170
196,869 285,775
196,887 285,795
190
235
330,2
8xM20
8xM24
160
102,8
11
196,869
196,887
235
8xM20
315,0
114,0
1000
15
170
285,775
285,795
190
330,2
8xM24
160
102,8
20
11
412,775
412,802
196,869
196,887
463,6
8xM24
235
8xM20
395,0
1250
15
190
285,775
285,795
190
330,2
8xM24
160
102,8
20
412,775
412,802
463,6
8xM24
950
Type 4313
1 set of solid
jaws
1 set of hard
top jaws
1 wrench
1 set of hard
master jaws
1 wrench
Optional
accessories
Type 4312
Standard
accessories
Other engineering data - see page 79
1 set of soft solid
jaws
1 set of soft solid
jaws
Spare parts - see page 80
Example of order: 4312-200/6
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
73
INDEPENDENT CHUCKS
Type 4334, 4335
4 JAW, CAST IRON BODY (DIN 55027)
Features
■■ 4 jaw, independent chuck with manual clamping, and a high quality
cast iron body
■■ Four jaws ensure the precise centering of square-shaped workpieces
with the maximum permitted gripping force
■■ Chucks with diameters of 250 mm and above are equipped with
additional T-slots, permitting the addition of extra jaws
■■ Mounted directly to BAYONET type machine-tool spindles
Application
■■ Suitable for machining square and round workpieces on all types of
workshop machining operations on conventional lathes
Options
■■ Hard solid jaws (type 4334) or hard two-piece jaws (type 4335)
■■ Chuck size: can be greater than 800 mm, but not exceeding 1250 mm
■■ Chuck design: our engineers can work with you to implement any
product design changes you may require
Chuck size
Short taper 1:4
B
D max
D min
E
F
Qty. of mounting screws
H
J
K
L
Approx. weight (kg) ca. kg
Chuck size
Short taper 1:4
B
D max
D min
E
F
Qty. of mounting screws
H
J
K
L
Approx. weight (kg) ca. kg
200
5
80
82,578
82,563
50
104,8
4
81
40,3
82
46,4
16,5
4
63,526
63,513
85
3
6
250
6
85
106,390
106,375
65
133,4
4
96,5
40,3
96,5
60,4
27,5
5
106,390
106,375
82,578
82,563
133,4
4
104,8
4
400
5
6
82,578
82,563
79,5
104,8
4
315
8
5
105
106,390 139,734
106,375 139,719
100
133,4
171,4
4
4
129
49,8
129
72,3
60,0
11
6
196,887
196,869
235
6
106,390
106,375
100
133,4
4
8
11
120
139,734 196,887
139,719 196,869
125
171,4
235
4
6
152,5
59,8
136
90,3
95,5
8
11
139,734
139,719
196,887
196,869
171,4
4
235
6
95
139,734
139,719
82,578
82,563
106,390
106,375
171,4
4
104,8
4
133,4
4
80
111
49,8
112,5
60,9
39,5
500
8
6
15
8
285,795
285,775
139,734
139,719
125
171,4
4
330,2
6
630
11
15
140
196,887 285,795
196,869 285,775
160
235
330,2
6
6
177
59,8
136
97,8
165,0
8
139,734
139,719
125
171,4
4
800
11
160
196,887
196,869
180
235
6
202
70,8
136
93,8
298,0
15
285,795
285,775
200
330,2
6
Type 4335
1 set of solid
jaws
1 set of hard
top jaws
1 wrench
1 set of hard
master jaws
1 wrench
Optional
accessories
Type 4334
Standard
accessories
Other engineering data - see page 79
Spare parts - see pages 58 and 80
Example of order: 4334-200/4
http://www.bison-bial.com, e-mail:[email protected] tel.+48 857 416 420
74
1 set of soft solid
jaws
1 set of soft solid
jaws
INDEPENDENT CHUCKS
Type 4332, 4333
4 JAWS, CAST STEEL BODY (DIN 55027)
■■ Four jaws ensure the precise centering of square-shaped
workpieces with the maximum permitted gripping force
■■ Chucks with diameters of 250 mm and above are equipped
with additional T-slots, permitting the addition of extra jaws
■■ Mounted directly to BAYONET type machine-tool spindles
Application
■■ This first class chuck, with increased clamping accuracy, is
made for all types of very high precision workshop machining
operations on conventional lathes
■■ Suitable for machining square and round workpieces
Options
■■ Hard solid jaws (type 4332) or hard two-piece jaws (type 4333)
■■ Chuck design: our engineers can work with you to implement
any product design changes you may require
Features
■■ 4 jaw, independent chuck with manual clamping, and a high
quality steel body
■■ Steel body extends machine life while providing higher rigidity
and greater wear resistance, enabling the chuck to withstand
higher machining forces
Chuck size
200
250
315
400
500
Short taper 1:4
5
6
5
6
8
5
6
8
11
5
6
8
11
6
8
11
15
B
80
85
95
105
120
D max
82,578 106,390 82,578 106,390 139,734 82,578 106,390 139,734 196,887 82,578 106,390 139,734 196,887 106,390 139,734 196,887 285,795
D min
82,563 106,375 82,563 106,375 139,719 82,563 106,375 139,719 196,869 82,563 106,375 139,719 196,869 106,375 139,719 196,869 285,775
E
50
65
80
79,5
100
100
125
F
104,8 133,4 104,8 133,4 171,4 104,8 133,4 171,4
235
104,8 133,4 171,4
235
133,4 171,4
235
330,2
Qty. of mounting screws
4
4
4
4
4
4
4
4
6
4
4
4
6
4
4
6
6
H
81
96,5
111
129
152,5
J
40,3
40,3
49,8
49,8
59,8
K
82
96,5
112,5
129
136
L
46,4
60,4
60,9
72,3
90,3
Approx. weight (kg)
16,5
27,5
39,5
60,0
95,5
Chuck size
Short taper 1:4
B
D max
D min
E
F
Qty. of mounting screws
H
J
K
L
Approx. weight (kg)
8
139,734
139,719
125
171,4
4
630
11
140
196,887
196,869
15
285,795
285,775
160
235
6
177
59,8
136
97,8
165,0
330,2
6
8
139,734
139,719
125
171,4
4
800
11
160
196,887
196,869
180
235
6
202
70,8
136
93,8
298,0
915
15
11
15
11
170
285,795
285,775
200
330,2
6
196,887
196,869
285,795
285,775
196,887
196,869
330,2
6
235
6
190
235
6
160
102,8
326,0
1000
15
170
285,795
285,775
190
330,2
6
160
102,8
386,0
1250
20
11
15
190
412,802
412,775
196,887
196,869
463,6
6
235
6
285,795
285,775
190
330,2
6
160
102,8
950
Type 4333
1 set of solid
jaws
1 set of hard
top jaws
1 wrench
1 set of hard
master jaws
1 wrench
Optional
accessories
Type 4332
Standard
accessories
Other engineering data - see page 79
1 set of soft solid
jaws
1 set of soft solid
jaws
Spare parts - see pages 58 and 80
Example of order: 4332-200/5
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
75
INDEPENDENT CHUCKS
Type 4344, 4345
4 JAW, CAST IRON BODY (DIN 55029)
Features
■■ 4 jaw, independent chuck with manual clamping, and a high quality
cast iron body
■■ Four jaws ensure the precise centering of square-shaped workpieces
with the maximum permitted gripping force
■■ Chucks with diameters of 250 mm and above are equipped with
additional T-slots, permitting the addition of extra jaws
■■ Mounted directly to CAMLOCK type machine-tool spindles
Application
■■ Suitable for machining square and round workpieces on all types of
workshop machining operations on conventional lathes
Options
■■ Hard solid jaws (type 4344) or hard two-piece jaws (type 4345)
■■ Chuck size: can be greater than 800 mm, but not exceeding 1250 mm
■■ Chuck design: our engineers can work with you to implement any
product design changes you may require
Chuck size
Short taper 1:4
B
D max
D min
E
F
Qty. of mounting screws
H
J
K
L
Approx. weight (kg) ca. kg
Chuck size
Short taper 1:4
B
D max
D min
E
F
Qty. of mounting screws
H
J
K
L
Approx. weight (kg) ca. kg
160
3
54
53,988
53,975
42
70,6
3
51
20
6,0
6
106,390
106,375
133,4
6
200
3
4
53,988
53,975
63,526
63,513
70,6
3
82,6
3
400
8
105
139,734
139,719
100
171,4
6
129
49,8
129
72,3
60,0
80
50
5
6
3
4
82,578
82,563
106,390
106,375
104,8
6
133,4
6
53,988
53,975
50
70,6
3
63,526
63,513
60
82,6
3
81
40,3
82
46,4
16,5
11
8
196,887
196,869
139,734
139,719
235
6
171,4
6
500
11
120
196,887
196,869
125
235
6
152,5
59,8
136
90,3
95,5
250
5
85
82,578
82,563
104,8
6
96,5
40,3
96,5
60,4
27,5
15
8
285,795
285,775
139,734
139,719
125
171,4
6
330,2
6
315
6
8
5
6
106,390
106,375
65
133,4
6
139,734
139,719
82,578
82,563
106,390
106,375
171,4
6
104,8
6
133,4
6
630
11
15
140
196,887 285,795
196,869 285,775
160
235
330,2
6
6
177
59,8
136
97,8
165,0
95
80
8
11
139,734
139,719
196,887
196,869
171,4
6
235
6
111
49,8
112,5
60,9
39,5
800
8
139,734
139,719
125
171,4
6
11
15
20
160
196,887 285,795 412,802
196,869 285,775 412,775
180
200
235
330,2
463,6
6
6
6
202
70,8
136
93,8
298,0
Type 4345
1 set of solid
jaws
1 set of hard
top jaws
1 wrench
1 set of hard
master jaws
1 wrench
Optional
accessories
Type 4344
Standard
accessories
Other engineering data - see page 79
Spare parts - see pages 58 and 80
Example of order: 4344-160/3
http://www.bison-bial.com, e-mail:[email protected] tel.+48 857 416 420
76
1 set of soft solid
jaws
1 set of soft solid
jaws
INDEPENDENT CHUCKS
Type 4342, 4343
4 JAWS, CAST STEEL BODY (DIN 55029)
Features
■■ 4 jaw, independent chuck with manual clamping, and a high
quality steel body
■■ Steel body extends machine life while providing higher rigidity
and greater wear resistance, enabling the chuck to withstand
higher machining forces
Chuck size
200
■■ Four jaws ensure the precise centering of square-shaped
workpieces with the maximum permitted gripping force
■■ Chucks with diameters of 250 mm and above are equipped
with additional T-slots, permitting the addition of extra jaws
■■ Mounted directly to CAMLOCK type machine-tool spindles
Application
■■ This first class chuck, with increased clamping accuracy, is
made for all types of very high precision workshop machining
operations on conventional lathes
■■ Suitable for machining square and round workpieces
Options
■■ Hard solid jaws (type 4342) or hard two-piece jaws (type 4343)
■■ Chuck design: our engineers can work with you to implement
any product design changes you may require
250
315
400
500
Short taper
3
4
5
6
3
4
5
6
8
5
6
8
6
8
11
6
8
11
15
1:4
B
80
85
95
105
120
D max
53,988 63,526 82,578 106,390 53,988 63,526 82,578 106,390 139,734 82,578 106,390 139,734 106,390 139,734 196,887 106,390 139,734 196,887 285,795
D min
53,975 63,513 82,563 106,375 53,975 63,513 82,563 106,375 139,719 82,563 106,375 139,719 106,375 139,719 196,869 106,375 139,719 196,869 285,775
E
50
50
60
65
80
100
100
125
F
70,6
85
104,8 133,4
70,6
82,6
104,8 133,4 171,4 104,8 133,4 171,4 133,4 171,4
235
133,4 171,4
235
330,2
Qty. of
mounting
screws
3
3
H
J
K
L
Approx.
weight (kg)
4
4
3
3
6
6
6
6
6
6
6
6
6
6
6
6
81
40,3
82
46,4
96,5
40,3
96,5
60,4
111
49,8
112,5
60,9
129
49,8
129
72,3
59,8
90,3
136
90,3
16,5
27,5
39,5
60,0
95,5
Chuck size
630
Short taper 1:4
8
B
D max
139,734
D min
139,719
E
125
F
171,4
Qty. of mounting screws
6
H
J
K
L
Approx. weight (kg)
800
11
15
140
196,887 285,795
196,869 285,775
160
235
330,2
6
6
177
59,8
136
97,8
165,0
8
139,734
139,719
125
171,4
6
11
915
15
20
160
196,887 285,795 412,802
196,869 285,775 412,775
180
200
235
330,2
463,6
6
6
6
202
70,8
136
93,8
298,0
11
1000
15
170
196,887 285,795
196,869 285,775
190
235
330,2
6
6
160
102,8
326,0
11
196,887
196,869
235
6
15
170
285,795
285,775
190
330,2
6
160
102,8
386,0
6
1250
20
412,802
412,775
463,6
6
11
15
190
196,887 285,795
196,869 285,775
190
235
330,2
6
6
160
102,8
950
Type 4343
1 set of solid
jaws
1 set of hard
top jaws
1 wrench
1 set of hard
master jaws
1 wrench
Optional
accessories
Type 4342
Standard
accessories
Other engineering data - see page 79
1 set of soft solid
jaws
1 set of soft solid
jaws
Spare parts - see pages 58 and 80
Example of order: 4342-200/6
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
77
INDEPENDENT CHUCKS
TYPE 4317-800/15 MSP
4 JAWS, STEEL BODY (55026)
Features
■■ 4 jaw, independent chuck with manual clamping, and a high
quality steel body
■■ The design of this lathe chuck allows workpieces to be
clamped with a gripping force of 20 000 daN per jaw
■■ Steel body extends machine life while providing higher rigidity
and greater wear resistance, enabling the chuck to withstand
higher machining forces
■■ Four jaws ensure the precise centering of square-shaped
workpieces with the maximum permitted gripping force
■■ Chucks with diameters of 250 mm and above are equipped
with additional T-slots, permitting the addition of extra jaws
■■ Mounted directly to “A” type machine-tool spindles
Application
■■ This first class chuck, with increased clamping accuracy, can
be used on machine tools with small clamping diameters for
applications requiring high gripping forces (i.e. for machining
heavy crank shafts, turbine rotors, etc.)
■■ Suitable for machining square and round workpieces
Technical Data:
Max speed
[min-1]
500
Gripping force per jaw
[daN]
20 000
Torque on wrench
[Nm]
110
Gripping range
[mm]
100-825
Dimensions:
[mm]
800
Heigth
[mm]
230
Approx. total weight (without top jaws)
[kg]
800
Type 4317
-800/15 MSP
Standard
accessories
Diameter
1 set of hard top
jaws
1 set of hard
master jaws
1 allen wrench
Example of order: 4317 - 800/15 MSP
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
78
1 hex wrench
ENGINEERING DATA FOR INDEPENDENT CHUCKS
GRIPPING RANGES
Chuck size
85
100
125
160
200
250
315
350
d1 min
d2 max
max swing dia
3
85
101
3
100
116
8
125
150
8
160
185
10
200
235
10
250
296
15
315
369
15
350
404
Chuck size
400
500
630
800
915
1000
1250
d1 min
d2 max
max swing dia
20
400
465
45
500
570
50
630
720
50
800
888
120
915
1003
170
1000
1088
170
1250
1338
Gripping ranges are valid for lathe chucks with reversible jaws. Do not exceed maximum chucking ranges.
MAXIMUM PERMISSIBLE ROTATIONAL SPEEDS * (rpm)
Chuck size
85
100
125
160
200
250
315
350
steel body or cast steel body
cast steel body
4000
-
3800
-
3500
-
3200
-
2500
1800
2000
1500
1500
1200
1500
1200
Chuck size
400
500
630
800
915
1000
1250
steel body or cast steel body
cast steel body
1100
800
700
500
550
400
450
300
200
150
200
150
150
100
* The specified permissible speeds are only applicable for work-pieces not exceeding a specific unbalance of 25 gmm/kg.
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
79
SPARE PARTS FOR INDEPENDENT CHUCKS
HARD SOLID REVERSIBLE JAWS
- SETS
Chuck size
mm
85
100
125
160
200
250
315
350
400
500
630
800
SOFT SOLID JAWS
- SETS
Code No 0642
Chuck size
mm
4 4-jaw set
985 731 002
985 740 101
985 731 104
985 731 104
985 731 206
985 731 308
985 731 400
985 731 400
985 731 501
985 731 603
985 731 705
985 731 807
85
100
125
160
200
250
315
350
400
500
630
800
200
250
315
400
500
630
800
915
1000
1250
Chuck size
mm
Ø 200 - 800
200
250
315
400
500
630
800
915
1000
1250
Ø 200 - 800
Code No 0642
Chuck size
mm
4-jaw set
985 735 200
985 735 301
985 735 403
985 735 505
985 735 607
985 735 709
985 735 800
985 735 902
985 735 902
985 735 902
HARD 2-PIECE REVERSIBLE JAWS - SETS
200
250
315
400
500
630
800
915
1000
1250
Ø 915 - 1250
Code No 0642
4-jaw set
985 738 202
985 738 304
985 738 406
985 738 508
985 738 600
985 738 701
985 738 803
985 742 908
985 742 908
985 742 908
Ø 915 -1250
Code No 0642
85
100
125
160
200
250
315
350
400
500
630
800
915
1000
1250
985 733 004
985 733 020
985 733 106
985 733 106
985 733 208
985 733 300
985 733 401
985 733 401
985 733 503
985 733 605
985 733 707
985 733 809
985 733 900
985 733 900
985 733 900
4-jaw set
985 736 200
985 736 302
985 736 404
985 736 506
985 736 608
985 736 700
985 736 801
985 744 900
985 744 900
985 744 900
Chuck size
mm
Code No 0642
85
100
125
160
200
250
315
350
400
500
630
800
915
1000
1250
985 732 003
985 732 029
985 732 105
985 732 105
985 732 207
985 732 309
985 732 400
985 740 509
985 732 502
985 732 604
985 732 706
985 732 808
985 740 702
985 740 804
985 740 906
SAFETY WRENCH
Chuck size Code No 0642 Code No 0642
mm
mm
for 4500, 4600, 4700, 4800
Example of order: Operating screw 4300 - 250
85
100
125
160
200
250
315
400
500
630
800
915
1000
1250
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
80
Code No 0642
OPERATING SCREW
THRUST BEARING
Chuck size
mm
4-jaw set
985 730 205
985 730 307
985 730 409
985 730 500
985 730 602
985 730 704
985 730 806
HARD TOP JAWS
- SETS
HARD MASTER JAWS - SETS
Chuck size
mm
Code No 0642
For chuck type For chuck type
4500, 4600,
4300
4700, 4800
985 754 001
985 754 014
985 754 103
985 754 205
985 754 307
985 754 307
-
985 340 102
985 340 102
985 344 106
985 344 106
985 344 208
985 344 208
985 344 300
985 344 300
985 344 401
985 344 401
985 344 503
985 344 503
985 344 503
985 344 503
MAIN DIMENSIONS OF ONE-PIECE
& TWO- PIECE REVERSIBLE JAWS
One-piece solid reversible jaws
Szczęka jednolita
Soft solid jaws
ø 200 - 800
Szczęka jednolita miękka
ONE-PIECE SOLID REVERSIBLE JAWS
Chuck size
85
100
125
160
200
250
A
B
C
D
E
F
H1
H
Tr-left hand
Approx. weight (kg)
34
13
30
4,5
5
7
8
17,5
Tr 16x2
0,1
34
13
30
4,5
5
7
8
17,5
Tr 16x2
0,1
51
16
34,5
6
5
8
12,5
31,5
Tr 18x4
0,12
51
16
34,5
6
5
8
12,5
31,5
Tr 18x4
0,12
81
32
63
8,7
10
14
17,5
48,5
Tr 28x5
0,72
96,5
32
63
8,7
10
14
23
59
Tr 28x5
1,3
Chuck size
315
350
400
500
630
800
A
B
C
D
E
F
H1
H
Tr-left hand
Approx. weight (kg)
111
40
76,5
9,7
12
18
27
67
Tr 32x6
1,5
111
40
76,5
9,7
12
18
27
67
Tr 32x6
1,5
129
40
76,5
9,7
12
18
32,5
78,5
Tr 32x6
1,8
152,5
52
93,5
11,7
15
22
35
93
Tr 36x6
3,4
177
52
93,5
11,7
15
25
45
109
Tr 40x6
4,0
202
70
114,5
15,7
20
25
44
122
Tr 44x8
7,8
Hard master jaws
HARD MASTER JAWS
Chuck size
A
B
C
D
E
F-0,03
G+0,01
H
J
K
L
Szczęka podstawowa
Hard top jaws
M
Tr-left hand
Approx. weight (kg)
200
250
315
400
500
630
800
915
1000
1250
79
94
110
129
168
206
206
244
244
244
32
32
40
40
52
52
70
70
70
70
32
38
39
44
59
59
59
59
59
59
8,7
8,7
9,7
9,7
11,7
11,7
15,7
15,7
15,7
15,7
10
10
12
12
15
15
20
20
20
20
7,94
12,7
12,7
12,7
12,7
12,7
12,7
12,7
12,7
12,7
12,69
19,04
19,04
19,04
19,04
19,04
19,04
19,04
19,04
19,04
33,2
37,5
45,4
54,9
55,5
55,5
55,5
55,5
55,5
55,5
4
4
4
7,2
7,2
7,2
7,2
7,2
7,2
7,2
22,25
27
31,75
38,1
38,1
38,1
38,1
38,1
38,1
38,1
14
20
17,5
22
33,5
33,5
33,5
33,5
33,5
33,5
M10
M12
M12
M16
M20
M20
M20
M20
M20
M20
3/8”-16 1/2”-13 1/2”-13 5/8”-11 3/4”-10 3/4”-10 3/4””-10 3/4”-10 3/4”-10 3/4”-10
Tr 28x5 Tr 28x5 Tr 32x6 Tr 32x6 Tr 36x6 Tr 40x6 Tr 44x8 Tr 44x6 Tr 44x6 Tr 44x8
0,6
0,9
1,1
1,2
1,5
2,4
2,4
5,4
5,4
5,4
HARD TOP JAWS
ø 200 - 800
ø 1000 - 1250
Chuck size
200
250
315
400
500
630
800
915
1000
1250
A
B
C
D
E
F-0,03
G + 0,01
H
J
K
L
M
N
0
P
R
Approx. weight (kg)
82
34
43,5
7,95
4
3,2
12,69
35,2
11
18
21,5
22,25
9,5
22
53
19,3
0,5
96,5
34
51,5
12,71
4
3,2
19,04
40
14
20
26,5
27
12
25
62
22,5
0,7
112,5
42
55
12,71
4
3,2
19,04
47,9
14
20
27,5
31,75
13
27
70,5
25,7
1,3
129
42
64,5
12,71
4
6,3
19,04
57,4
18
26
32
38,1
13,5
26,5
79
28,8
2,1
136
54
74,5
12,71
4
6,3
19,04
58
22
33
39,5
38,1
18
37,5
87
29,4
3,0
136
54
82
12,71
4
6,3
19,04
58
22
33
43
38,1
21
37,5
87
29,4
3,0
136
72
88
12,71
4
6,3
19,04
58
22
33
46
38,1
24
40
89
29,4
4,2
160
72
97
12,71
4
6,3
19,04
58
22
33
71
38,1
50
60
29,4
4,2
160
72
97
12,71
4
6,3
19,04
58
22
33
71
38,1
50
60
29,4
4,2
160
72
97
12,71
4
6,3
19,04
58
22
33
71
38,1
50
60
29,4
4,2
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
81
MOUNTING BOLTS FOR TOP JAWS
Chuck size
Bolt 1
Bolt 2
200
250
315
400
500
630
800
915
1000
1250
M10x30
M12x40
M12x40
M16x45
M20x55
M20x60
M20x65
M20x45
M20x45
M20x45
M10x20
M12x25
M12x25
M16x30
M20x40
M20x40
M20x40
M20x45
M20x45
M20x45
Szczęka górna twarda
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
82
SELF-CENTERING WEDGE BAR CHUCKS
Features
■■ Jaw locking system
■■ Hardened and ground jaw guides ensure
longer life with maintained accuracy and
repeatability
■■ Steel body extends machine life while
providing higher rigidity and greater wear
resistance, enabling the chuck to withstand
higher machining forces
Application
■■ This first class chuck, with increased
clamping accuracy, is Designed for turning
work demanding high concentricity, reliable
repeatability and high gripping force
Options
■■ Hard solid jaws or hard two-piece jaws
Standard accessories
■■ 1 set of hard solid jaws
■■ 1 wrench
■■ 1 set of mounting screws
Optional accessories
■■ 1 set of hard top jaws
Jaw weight in dimensions tables; Spare parts - see page 86; Engineering data - see page 85
SELF-CENTERING 3 JAW WEDGE BAR CHUCKS, HARD SOLID JAWS
Chuck size
Short taper
1:4
125
160
200
250
315
-
125
125
160
160
200
200
250
250
315
315
3
4
4
5
5
6
6
8
8
11
B
Approx.
weight (kg)
67
84
97
112
127
5,6
11,8
20
36
60
Type 3404
DIN 55027
Chuck size
Short taper
1:4
160
160
200
200
250
250
315
315
4
5
5
6
6
8
8
11
125
125
160
160
200
200
250
250
315
315
3
4
4
5
5
6
6
8
8
11
DIN 55026
Type 3434
5,9
6,3
11,4
13
21,4
22,8
35,5
36,7
64
66,5
Approx.
weight (kg)
84,5
92
99
105
117
122
136
139
11
13
21
22
35,5
36,7
64
65,5
Type 3414
DIN 55029
70
74
84,5
92
99
105
117
122
136
139
B
Type 3444
70
74
84,5
92
99,5
105
126
129
142
144
5,9
6,3
11,4
13
21,4
22,8
39
40,3
66
68
Example of order: 3444-315/11
MAIN DIMENSIONS OF WEDGE BAR CHUCKS
Chuck size
125
160
200
250
315
A
B
C
D
E
F
G
H
J
K
L
M
N
S
130
67
4
95
30
108
3xM8
16
51,5
35,5
150
9
125
5,2
165
84
5
125
40
140
3xM10
17
65
45,5
200
11
130
5,2
205
97
5
160
51
176
3xM12
20
73,5
56,5
290
14
149
5,6
252
112
6
200
66
224
3xM16
24
84,5
72
440
16
173
6,2
315
127
6
260
90
286
3xM18
30
95,5
88
500
18
219
9,1
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
83
MAIN DIMENSIONS FOR WEDGE BAR CHUCK JAWS
HARD SOLID REVERSIBLE JAWS
ø 125
Szczęka górna twarda
ø 160-315
Chuck size
125
160
200
250
315
A
B
C
D
E
F
G
H
J
a
b
Approx. weight (kg) ca. kg
58
14
40
6,5
7
7
16
32
48
8
12
0,4
69
20
45
7,5
9
8
26
58
10
12
1,0
90
22
50
8
9
11,5
33
72,5
12
15
1,5
108,5
26
60
10
11
14
36
83
15
20
2,6
132
32
70
12
14
17
41,5
104,5
20
20
4,4
HARD TOP JAWS
ø 125
Szczęka górna miękka
ø 160-315
ø 125
Chuck size
125
160
200
250
315
A
B h11
C
D H9
E
F
G h7
H
J
K
L
M
N
0
P
R
S
Approx. weight (kg) ca. kg
59
20
36
14
1,5
5
5
26
6,4
10,4
6
10
7
16
31
18,5
47
0,18
63
20
37
8
3
4,5
18
23
8,4
13,5
9
16
7,5
27
40
16
0,25
72,5
22
43,5
10
3,5
5
20
27
8,4
13,5
9
20
9,5
33
58
17
91
30
55
12
3,5
5
20
30
13
19
7
20
14
40,5
81
20
0,50
105
35
60
12
6,5
5
26
35,3
13
19
15,5
27
15
40
95
21
0,80
0,35
HARD MASTER JAWS
ø 160-315
Chuck size
125
160
200
250
315
A
B
C
D
E
F
G H7 1)
H
J
K
L
M
S
Approx. weight (kg) ca. kg
51,5
14
21,5
6,5
7
5
25,75
3
10
10
M6
0,3
65
20
26,5
7,5
9
8
18
28
5
32
12
M8
2,5
0,6
85
22
28,5
8
9
10
20
42
5,5
40
12
M8
2,5
0,9
87,5
26
36
10
11
12
20
41,5
5,5
40
17
M12
3
1,8
125
32
42
12
14
12
26
69
7
54
17
M12
3
3,0
1) H7 without chuck size 125
ø 125
SOFT TOP JAWS
ø 160-315
Chuck size
125
160
200
250
315
A
B
C
D H9
E
F
G h7
H
J
K
L
M
Approx. weight (kg) ca. kg
55
20
30
14
1,5
5
5
25
6,4
10,4
24
20
0,6
85
20
40
8
4,5
3
18
35
8,4
13,5
26,5
32
1,2
105
22
50
10
5
3
20
40
8,4
13,5
35
40
2,1
125
30
55
12
5
3,5
20
60
13
19
41
40
4,2
145
35
60
12
6
3,5
26
60
13
19
38
54
6,2
http://www.bison-bial.com, e-mail:[email protected] tel.+48 857 416 420
84
MAIN DIMENSIONS FOR WEDGE BAR CHUCK JAWS
GRIPPING RANGES
Chuck size
125
160
200
250
315
d1
d2
d3
d4
d5
max. swing dia
4-29
38-63
100-125
28-53
100-125
151
4-90
61-150
90-160
34-120
90-160
212
5-105
70-170
100-200
49-149
100-200
264
8-130
81-170
120-250
66-188
128-250
322
10-155
95-189
152-315
74-200
142-315
393
MAXIMUM PERMISSIBLE ROTATIONAL SPEEDS (rpm)
Chuck size
125
160
200
250
315
max. rpm
6000
5400
4600
4200
3300
TOTAL GRIPPING FORCE
Chuck size
125
160
200
250
Torque on wrench (Nm)
Total gripping force (daN)
40
3000
100
6000
160
8500
200
11000
250
13000
BALANCE VALUE
Chuck size
125
160
200
250
315
gcm
16
32
63
125
250
CENTERING ACCURACY
Chuck size
d
l
w
125
160
200
250
315
14
20
29
60
95
125
14
20
39
60
95
160
14
22
50
80
125
200
15
32
64
80
180
245
20
64
89
120
189
290
0,015
0,010
0,015
0,015
0,010
0,015
0,015
0,010
0,015
0,020
0,010
0,020
Centering accuracy (mm)
a
b
c
0,015
0,010
0,015
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
85
SPARE PARTS FOR WEDGE BAR CHUCKS
HARD SOLID JAWS - SET
Code No 0642 985
Chuck size
mm
3 pcs/set
985 309 108
985 309 200
985 309 301
985 309 403
985 309 505
125
160
200
250
315
SOFT TOP JAWS - SET
Code No 0642
Chuck size
mm
3 pcs/set
985 310 301
985 310 403
985 310 505
985 310 607
985 310 709
125
160
200
250
315
SOFT 2-PIECE JAWS - SET
Code No 0642
Chuck size
mm
3 pcs/set
985 312 700
985 312 802
985 312 904
985 312 920
985 312 945
125
160
200
250
315
HARD MASTER JAWS - SET
Code No 0642
Chuck size
mm
3 pcs/set
985 309 709
985 309 800
985 309 902
985 310 006
985 310 108
125
160
200
250
315
HARD TOP JAWS - SET
Code No 0642
Chuck size
mm
3 pcs/set
985 310 813
985 310 826
985 310 839
985 310 841
985 310 854
125
160
200
250
315
SOFT 2-PIECE REVERSIBLE JAWS - SET
Chuck size
mm
125
160
200
250
315
Code No 0642
3 pcs/set
985 312 100
985 312 201
985 312 303
985 312 405
985 312 507
http://www.bison-bial.com, e-mail:[email protected] tel.+48 857 416 420
86
FULLY-MACHINED ADAPTER PLATES
Type 8210
Type 8230
Type 8240
Cast-iron adapters for plain back self-centering chucks.
Allowance for turning on the chuck side. For mounting instructions, see the chuck service manual.
DIN 55026 - Typ 8210
DIN 55026 - Type 8210
DIN 55027 - Typ 8230
DIN 55027 - Type 8230
Size
mm
Short taper
1:4
A
mm
100
125
125
160
160
160
200
200
200
200
250
250
250
315
315
315
400
400
400
500
500
500
630
630
630
3
3
4
3
4
5
3
4
5
6
5
6
8
6
8
11
6
8
11
8
11
15
8
11
15
100,5
125,5
125,5
160,5
160,5
160,5
201
201
201
201
251
251
251
316
316
316
402
402
402
502
502
502
633
633
633
Size
mm
Short taper
1:4
100
125
125
160
160
160
160
200
200
200
200
200
250
250
250
250
315
315
315
400
400
400
500
500
500
630
630
630
3
3
4
3
4
5
6
3
4
5
6
8
4
5
6
8
6
8
11
6
8
11
8
11
15
8
11
15
B
mm
B
mm
Type 8210
Type 8230
18,5
18,5
18,5
18,5
21
21
21
21
21
21
21
26
26
33
33
33
33
33
33
34
34
34
42
42
42
16,5
18,5
18,5
21
21
21
21
21
21
21
21
21
26
33
33
33
33
33
33
34
34
34
42
42
42
A
mm
Approx. weight
(kg)
1,6
2,4
2,4
4,3
4,3
4,3
7,0
7,0
7,0
7,0
11,0
11,0
18,0
18,0
18,0
18,0
36,0
36,0
36,0
60,0
60,0
60,0
105,0
105,0
105,0
B
mm
Approx. weight (kg)
26
26
26
27
27
30
36,5
27
27
30
36,5
40
28
30
36,5
39
39,5
42
47
36,5
39
47
39
47
50
39
47
50
1,6
2,4
2,4
4,3
4,3
4,3
4,3
7,0
7,0
7,0
7,0
7,0
11,0
11,0
18,0
18,0
18,0
18,0
18,0
36,0
36,0
36,0
60,0
60,0
60,0
105,0
105,0
105,0
Type 8240
DIN 55029 - Type 8240
100,5
125,5
125,5
160,5
160,5
160,5
160,5
201
201
201
201
201
251
251
251
251
316
316
316
402
402
402
502
502
502
633
633
633
Example of order: 8240-200/6
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
87
FULLY-MACHINED ADAPTER PLATES
8235-400 ø 8235-630
8235-100 ø 8235-315
DIN 55027 - Type 8235
BAYONET
Size
mm
A
mm
Short
taper
1:4
B
B1
100
105
125
125
130
3
4
3
4
5
3
4
5
4
5
6
5
6
8
6
8
11
6
8
11
8
11
15
8
11
15
31
31
33
33
35
32
32
37
33
33
40
38
38
43
43
43
50
35
37
37
36
36
52
36
36
52
12
12
14
14
14
16
16
16
17
17
17
19
19
19
19
19
19
-
C
D
E
F
G
H
Approx.
weight
(kg)
20
20
35
35
35
42
42
42
55
55
55
76
76
76
103
103
103
103
135,8
120
136
192,8
190
136
192,8
252
75
85
75
85
104,8
75
85
104,8
85
104,8
133,4
104,8
133,4
171,4
133,4
171,4
235
133,4
171,4
235
171,4
235
235
171,4
330,2
330,2
M8
M8
M8
M8
M8
M10
M10
M10
M10
M10
M10
M12
M12
M12
M16
M16
M16
M16
M16
M16
M20
M20
M20
M20
M20
M20
83
83
108
108
108
140
140
140
176
176
176
224
224
224
286
286
286
171,4
171,4
171,4
235
235
235
330,2
330,2
330,2
1,3
1,2
1,8
1,7
1,8
2,8
2,8
3,0
4,0
4,4
5,3
8,4
7,9
10,3
12,9
15,0
17,9
12,8
15,0
17,0
31,5
29,6
39
31,5
29,6
34
160
160
200
200
G
G
125
H
A
F
E
C
D
H
A
F
100
E
Type 8235 DIN 55027
B1
Wielkość
B
B
Ø 100ø100
- 315 ÷ ø315
250
315
315
400
298,45
500
407
BWielkość
630
407
E
250
G
A
F
E
C
H
8235-400 ø 8235-630
15
B1
B
ø400
Ø 400
- 630÷ ø630
45
45
55
55
55
86
86
86
110
110
110
145
145
145
180
180
180
298,45
298,45
298,45
407
407
407
407
407
407
53,975
63,513
53,975
63,513
82,563
53,975
63,513
82,563
63,513
82,563
106,375
82,563
106,375
139,719
106,375
139,719
196,869
106,375
139,719
196,869
139,719
196,869
285,775
139,719
196,869
285,775
8245-400 ø 8245-630
CAMLOCK
DIN 55029 - Type 8245
8245-100 ø 8245-315
Size
mm
A
mm
Short
taper
1:4
100
100
108
3
4
3
4
5
3
4
5
6
3
4
5B
6
4
5
6
8
6
8
11
6
8
11
8
11
15
8
11
15
B
B1
38
40
40
39
44
46
46
46
51
33
33
47
51
38
38
53
60
38
57
64
35
38
48
36
36
52
36
36
52
12
12
14
14
14
16
16
16
16
17
17
17
17
19
19
19
19
19
19
19
-
C
D
E
F
G
H
Approx.
weight
(kg)
20
20
35
35
35
42
42
42
42
51,4
55
55
55
60,5
76
76
76
103
103
103
103
136,1
136
136
192,8
190
136
192,8
252
70,6
82,6
70,6
82,6
104,8
70,6
82,6
104,8
133,4
70,6
82,6
104,8
133,4
82,6
104,8
133,4
171,4
133,4
171,4
235
133,4
171,4
235
171,4
235
330,2
171,4
235
330,2
M8
M8
M8
M8
M8
M10
M10
M10
M10
M10
M10
M10
M10
M12
M12
M12
M12
M16
M16
M16
M16
M16
M16
M20
M20
M20
M20
M20
M20
83
83
108
108
108
140
140
140
140
176
176
176
176
224
224
224
224
286
286
286
171,4
171,4
171,4
235
235
235
330,2
330,2
330,2
1,5
1,8
2,7
2,6
3,1
4,9
4,5
4,5
5,9
4,7
4,7
7,2
8,0
8,6
8,0
12,9
14,7
12,9
21,7
24,0
11,7
11,9
17,5
33,5
35,3
37,8
33,5
35,3
32,8
135
G
160
160
170
B1
Wielkość
B
200
200
250
250
315
315
400
298,45
500
407
630
407
G
E
F
H
A
E
C
ø100 ÷ ø315
8245-400 ø 8245-630
Ø 100 - 315
1
B
Ø 400 - 630
E
125
G
125
F
H
A
E
C
A
F
H
Type 8245 DIN 55029
45
45
55
55
55
86
86
86
86
110
110
110
110
145
145
145
145
180
180
180
183
227
297
407
407
407
407
407
407
53,975
63,513
53,975
63,513
82,563
53,975
63,513
82,563
106,375
53,975
63,513
82,563
106,375
63,513
82,563
106,375
139,719
106,375
139,719
196,869
106,375
139,719
196,869
139,719
196,869
285,775
139,719
196,869
285,775
Example of order: 8245-160/3
http://www.bison-bial.com, e-mail:[email protected] tel.+48 857 416 420
88
SEMI-FINISHED ADAPTER PLATES
Cast-iron adapters for plain back self-centering and independent chuck, rough on the chuck side.
For mounting instructions, see the chuck service manual.
Size
mm
Short taper
1:4
A
mm
100
125
125
160
160
160
200
200
200
250
250
250
315
315
315
400
400
500
500
630
630
800
800
3
3
4
3
4
5
4
5
6
5
6
8
6
8
11
8
11
8
11
11
15
11
15
102
127
127
162
162
162
203
203
203
253
253
253
318
318
318
405
405
505
505
635
635
385
408
DIN 55026 I DIN 55027
DIN 55026
Type 8212
DIN 55026
Typ 8212
DIN 55027
Type 8232
DIN 55027
Typ 8232
DIN 55029
Type 8242
B
mm
B
mm
B
mm
Approx. weight
(kg)
Type 8212
Type 8232
Type 8242
18
19,5
19,5
24
24
38
33
33
50
46
33
55
55
43
75
45
45
45
56
45
45
18
19,5
19,5
24
24
38
33
33
50
46
33
55
47
43
47
45
45
45
56
45
45
28
50
30
50
55
35
44
50
35
49
49
49
70
55
55
70
50
46
72
72
60
50
55
1,8
2,4
2,4
4,2
4,2
4,2
12,0
12,0
12,0
16,0
16,0
16,0
22,0
22,0
22,0
42,0
42,0
72,0
72,0
105,0
105,0
130,0
130,0
8215-100 ö 8215-315
FULLY-MACHINED ADAPTER PLATES
Steel adapters, fully machined, for self-centering with fine adjustment chucks type 3564, 3565 and 3864, 3865,
G
DIN 55026 - Type 8215
G
K
FORM A MOUNTING
Size
mm
A
mm
Short
taper
1:4
B
B1
C
100
100
105
125
125
160
160
200
200
3
4
4
5
3
4
5
6
4
5
6
5
6
8
6
8
11
6
8
11
8
11
15
8
11
15
40
40
36
36
45
45
37
42
33
33
45
38
38
46
38
46
55
35
37
48
36
36
52
36
36
52
12
12
14
14
16
16
16
16
17
17
17
19
19
19
19
19
19
-
45
45
55
55
86
86
86
86
110
110
110
145
145
145
180
180
180
298,45
298,45
298,45
407
407
407
407
407
407
D
E
F
G
H
K
Approx.
weight
(kg)
70,6
82,6
82,6
104,8
70,6
82,6
104,8
133,4
82,6
104,8
133,4
104,8
133,4
171,4
133,4
171,4
235
133,4
171,4
235
171,4
235
330,2
171,4
235
330,2
M8
M8
M8
M8
M10
M10
M10
M10
M10
M10
M10
M12
M12
M12
M16
M16
M16
M16
M16
M16
M20
M20
M20
M20
M20
M20
83
83
108
108
140
140
140
140
176
176
176
224
224
224
286
286
286
171,4
171,4
171,4
235
235
235
330,2
330,2
330,2
14
14
22
22
20
29
21
26
16
16
28
19
19
26
19
27
36
35
29
27
36
36
52
36
36
52
1,6
1,5
2,2
1,9
4,4
4,4
3,1
3,3
4,4
4,2
6,2
7,8
7,9
9,2
12,3
16,0
18,7
14,3
12,8
16,2
31,5
27,6
34,6
31,5
27,6
29,6
E
F
H
A
A
E
C
F
H
Type 8215 DIN 55026
Size
Ø 100 - 315
ø100 ÷ ø315
250
250
315
315
400
298,45
500
407
630
407
G
8215-100 ö 8215-315
N
B1
B
E
C
F
H
E
F
H
A
G
K
B1
N
B
B
Ø 400 - 630
B
53,975
63,513
63,513
82,563
53,975
63,513
82,563
106,375
63,513
82,563
106,375
82,563
106,375
139,719
106,375
139,719
196,869
106,375
139,719
196,869
139,719
196,869
285,775
139,719
196,869
285,775
20
20
35
35
42
42
42
42
55
55
55
76
76
76
103
103
103
136
136
136
136
192,8
190
136
192,8
252
Example of order: 8215-200/4
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
89
B3
N
M
FULLY-FINISHED ADAPTER PLATES
400 ÷ 630
A
K
G
TYPE 8210-X
D
F
1:4
S
P1
.
.
B2
.
P
B1
B
DIN 55026
Fully finished cast-iron adapters for plain back self-centering chucks. For direct mounting on spindle nose type A.
FORM A MOUNTING
Size
Short
taper
1:4
A
mm
B
B1
B2
B3
D
F
K
M
N
P
P1
S
Approx.
weight (kg)
70
83
3x8,4
-
3xM10
-
108
3x13,5
-
3xM8
95
3xM8
3xM10
-
6x16,5
6x10,5
-
-
3x16,5
3x10,5
-
-
6x16,5
6x10,5
6xM12
0,766
1,362
1,249
2,392
2,24
1,94
1,567
3,235
3,09
2,784
2,69
3,884
3,57
3,09
3xM10
7,092
G(h4)
Type 8210-X
100
125
160
180
200
230
250
270
315
400
450
500
630
3
3
4
3
4
5
6
3
4
5
6
4
5
6
100
22
2,5
125
22
3,5
21
70,6
70,6
82,6
70,6
82,6
104,8
133,4
70,6
82,6
104,8
133,4
82,6
104,8
133,4
51,4
51,4
60,9
51,4
60,9
79,5
103
51,4
60,9
79,5
103
60,9
79,5
103
3
13
70,6
51,4
4
5
6
5
6
8
5
6
8
6
8
11
6
8
11
8
8
11
15
8
11
15
12
17
19
12
19
24
17
19
24
19
22
32
21
20
30
20
20
30
32
22
24
36
82,6
104,8
133,4
104,8
133,4
171,4
104,8
133,4
171,4
133,4
171,4
235
133,4
171,4
235
171,4
171,4
235
330,2
171,4
235
330,2
60,9
79,5
103
79,5
103
138,1
79,5
103
136,1
103
136,1
192,8
103
136,1
192,8
136,1
136,1
192,8
281,4
136,1
192,8
281,4
160
22
3,5
14
14
13
14
15
19,5
12
180
22
3,5
25
200
230
22
28
21
3,5
4,5
250
28
4,5
270
28
4,5
315
33
4,5
38
400
36
15
4,5
450
40
4,5
500
36
4,5
630
42
6
15
10
10
10
10
12
12
12
16
16
17
17
16
19
3xM10
125
145
160
191
140
160
176
208
3x19
3x13
3xM10
-
3xM12
3xM10
3xM10
6xM10
-
6xM12
3xM10
3xM12
200
224
6x19
6x13
3xM12
228
246
3x19
3x13
3xM12
260
286
6x25
6x17
-
-
3xM16
330
362
6x25
6x17
6xM16
386
415
6x25
6x17
3xM16
420
458
6x25
6x17
6xM16
545
586
6x25
6x17
6xM16
Example of order: Adapter 8210-200/5-X
http://www.bison-bial.com, e-mail:[email protected] tel.+48 857 416 420
90
6xM10
6xM10
6xM10
6xM12
6xM10
6xM12
6xM16
6xM10
6xM12
6xM16
6xM12
6xM16
6xM18
6xM12
6xM16
6xM18
6xM16
6xM16
6xM18
6xM22
6xM16
6xM18
6xM22
-
-
-
-
-
3xM16
3xM16
3xM16
3xM16
6,904
6,617
5,94
7,724
7,07
5,93
9,597
8,92
7,784
14,637
13,19
11,832
27,665
26,03
22,33
38,54
43,38
39,66
31,65
83,978
79,47
79,08
FULLY-FINISHED ADAPTER PLATES
B3
400 ÷ 630
N
M
B1
A
G
K
.
S
P
F
TYPE 8230-X
D
1:4
B2
B
DIN 55027
Fully finished cast-iron adapters for plain back self-centering chucks. For direct mounting on BAYONET spindle nose.
BAYONET
Size
Short
taper
1:4
A
mm
B
B1
B2
D
3
3
4
3
4
5
6
3
4
5
6
3
4
5
6
4
5
6
5
6
8
5
6
8
6
8
11
6
8
11
8
11
8
11
15
8
11
15
100
22
2,5
125
22
3,5
160
22
3,5
180
22
3,5
200
22
3,5
230
28
4,5
250
28
4,5
270
28
4,5
315
33
4,5
400
36
4,5
450
40
4,5
500
36
4,5
630
42
6
34
34
39
34
39
43
50
34
39
43
50
34
39
43
50
39
43
50
43
50
60
43
50
60
50
60
75
50
60
75
60
75
60
75
90
60
75
90
70,6
70,6
82,6
70,6
82,6
104,8
133,4
70,6
82,6
104,8
133,4
70,6
82,6
104,8
133,4
82,6
104,8
133,4
104,8
133,4
171,4
104,8
133,4
171,4
133,4
171,4
235
133,4
171,4
235
171,4
235
171,4
235
330,2
171,4
235
330,2
F
G(h4)
K
M
N
P
S
70
83
3x13,5
3x8,4
6xM8
-
95
108
3x13,5
3x8,4
6xM8
-
125
140
6x16,5
6x10,5
6xM10
-
154
160
3x16,5
3x10,5
6xM10
-
160
176
6x16,5
6x10,5
6xM10
-
191
208
3x19
3x13
6xM12
-
200
224
6x19
6x13
6xM12
-
228
246
3x19
3x13
6xM12
-
260
286
6x25
6x17
6xM16
-
330
362
6x25
6x17
6xM16
3xM16
386
415
6x25
6x17
6xM16
3xM16
420
458
6x25
6x17
6xM16
3xM16
545
586
6x25
6x17
6xM16
3xM16
Approx.
weight
(kg)
Type 8230-X
100
125
160
180
200
230
250
270
315
400
450
500
630
51,4
51,4
60,9
51,4
60,9
79,5
103
51,4
60,9
79,5
103
51,4
60,9
79,5
103
60,9
79,5
103
79,5
103
136,1
79,5
103
136,1
103
136,1
192,8
103
136,1
192,8
136,1
192,8
136,1
192,8
281,4
136,1
192,8
281,4
0,91
1,56
1,424
2,58
2,464
2,23
1,88
3,43
3,304
3,08
2,74
4,21
4,094
3,86
3,55
7,234
6,92
6,44
8,05
7,57
6,71
9,9
8,62
8,56
15,13
14,02
12,18
28,163
26,893
24,703
39,373
36,733
44,253
42,063
35,661
84,763
81,893
74,021
Example of order: Adapter 8230-160/5-X
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
91
FULLY-FINISHED ADAPTER PLATES
B3
400 ÷ 630
N
M
B1
A
K
S
P
F
TYPE 8240-X
G
1:4
B2
B
DIN 55029
Fully finished cast-iron adapters for plain back self-centering chucks. For direct mounting on CAMLOCK spindle nose.
CAMLOCK
Size
Short
taper
1:4
A
mm
B
B1
B2
F
4
3
4
5
5
3
4
5
6
5
6
5
6
8
6
8
6
8
11
8
11
8
11
8
11
11
15
125
26
3,5
32,2
30,8
32,2
38,2
38,2
30,8
32,8
38,2
44,2
38,2
44,2
38,2
44,2
50,7
44,2
50,7
44,2
50,7
60,6
50,7
60,6
50,7
60,6
50,7
60,6
60,6
69,6
60
51,4
60
79,5
79,5
51,4
60
79,5
103
79,5
103
79,5
103
136,1
103
136,1
103
136,1
192,8
136,1
192,8
136,1
192,8
136,1
192,8
192,8
281,4
K
M
N
P
S
Approx.
weight (kg)
95
108
3x13,5
3x8,4
6xM8
-
125
140
6x16,5
6x10,5
6xM10
-
145
160
3x16,5
3x10,5
6xM10
-
160
176
6x16,5
6x10,5
6xM10
-
191
208
3x19
3x13
6xM12
-
200
224
6x19
6x13
6xM12
-
228
246
3x19
3x13
6xM12
-
260
286
6x25
6x17
6xM16
-
330
362
6x25
6x17
6xM16
3xM16
386
415
6x25
6x17
6xM16
3xM16
420
458
6x25
6x17
6xM16
3xM16
545
586
6x25
6x17
6xM16
3xM16
1,56
3,07
2,911
2,962
4,159
5,077
4,944
4,745
5,94
6,876
7,502
8,605
8,724
9,393
10,436
10,528
17,376
15,936
16,304
27,353
27,431
39,627
42,84
45,405
44,531
74,48
70,339
G(h4)
Type 8240-X
125
160
180
200
230
250
270
315
400
450
500
630
160
180
27
30
30
3,5
3,5
27
200
230
250
270
315
400
450
500
630
30
36,5
30
36,5
30
36,5
39
36,5
39
39
47
39
47
40
47
39
47
47
50
3,5
4,5
4,5
4,5
4,5
4,5
4,5
4,5
6
Example of order: Adapter 8240-160/4-X
http://www.bison-bial.com, e-mail:[email protected] tel.+48 857 416 420
92
MACHINE SPINDLE NOSES
DIN 55026 Type A Type B - ISO 702/I Type A2 Type A1-A2
B
A 1-A 2
C1
D
C2
E1
7° 7' 30''
F2
E1
E1
E2
B
A
F1
B
A
7° 7' 30''
F1
E1
A
A2
From taper 4
D
Spindle nose
size
A
B max
C1
C2
D
E1
F1
E2
F2
3
4
5
6
8
92
108
133
165
210
53,983
63,521
82,573
106,385
139,731
11
11
13
14
16
14,288
15,875
17,462
16
20
22
25
28
70,6
82,6
104,8
133,4
171,4
280
196,,883
18
19,05
35
15
380
285,791
19
20,638
42
20
28
520
725
412,795
584,248
21
24
22,225
25,400
48
56
8xM10
8xM12
8xM16
8xM20
(8xM18)
11xM24
(11xM22)
11xM24
11xM30
61,9
82,6
111,1
11
3xM10
11xM10
11xM10
11xM12
11xM16
11xM20
(11xM18)
12xM24
(12xM22)
12xM24
12xM30
235
330,2
463,6
647,6
165,1
247,6
368,3
530,2
Type A: Tapped holes in flange (outer bolt circle) without inner bolt circle
Type B: Tapped holes in flange (outer bolt circle) and in inner bolt circle
Dimensions in brackets according to ISO 702/I
DIN 55027 & ISO 702/III
WITH BAYONET RING FIXING
B
A
Spindle nose
size
A
B max
C
D
E
F
3
4
5
6
8
11
15
20
102
112
135
170
220
290
400
540
53,983
63,521
82,573
106,385
139,731
196,883
285,791
412,795
11
11
13
14
16
18
19
21
16
20
22
25
28
35
42
48
3x21
3x21
4x21
4x23
4x29
6x36
6x43
6x43
75
85
104,8
133,4
171,4
235
330,2
463,6
E
F
7° 7' 30''
From taper 4
C
D
CAMLOCK FIXING
F
B
A
7° 7' 30''
E
DIN 55029, ANSI B 5,9 & ISO 702/II
Spindle nose
size
A
B max
C
D
E
F
3
4
5
6
8
11
15
20
92
117
146
181
225
298
403
546
53,983
63,521
82,573
106,385
139,731
196,883
285,791
412,795
11
11
13
14
16
18
19
21
32
34
38
45
50
60
70
82
3x15,1
3x16,7
6x19,8
6x23
6x26,2
6x31
6x35,7
6x42,1
70,6
82,6
104,8
133,4
171,4
235
330,2
463,6
C
D
DIN 800
WITH THREAD
A
B
C
F
A
Bg5
C min
D
E
F
M 20
M 24
M 33
M 39
M 45
M 52
M 60
M 76x6
M 105x6
21
25
34
40
46
55
62
78
106
30
36
50
56
67
80
90
112
150
6.3
8
9
10
11
12
14
16
20
10
12
14
16
18
20
22
30
40
20
24
30
35
40
45
50
63
80
E
D
http://www.bison-bial.com, e-mail:[email protected], tel.+48 857 416 420
93
MACHINE SPINDLE NOSES TO ANSI B 5.9; ASA B 5.9
A1
7° 7' 30''
A
F2
B
F1
E2
E1
TYPE A1 - A2
Spindle nose
size
A
B max
C
-0,025
D
E1
F1
E2
F2
5
6
8
11
15
20
133.4
165.1
209.5
279.4
381
520
82.575
106.390
139.735
196.885
285.8
412.8
14.288
15.875
17.462
19.05
20.638
22.225
22.2
25.4
28.6
34.9
41.3
47.6
11x7/16-14 UNC
11x1/2-13 UNC
11x5/8-11 UNC
11x3/4-10 UNC
12x7/8-9 UNC
12x1-8 UNC
104.8
133.4
171.4
235
330.2
463.6
8x7/16-14 UNC
8x1/2-13 UNC
8x5/8-11 UNC
8x3/4-10 UNC
11x7/8-9 UNC
11x1-8 UNC
61.9
82.6
111.1
165.1
247.6
368.3
E1
Tapped holes in flange (outer bolt circle) without inner bolt circle
C
From taper 4
D
A2
A
F2
E1
7° 7' 30''
B
F1
E2
E1
TYPE A2
Spindle nose
size
A
3
92.1
4
108
B
max
C
D
E1
F1
53.985
11.1
15.9
3x7/16-14 UNC
70.66
63.525
11.1
19
11x7/16-14 UNC
82.55
5
133.4
82.575
12.7
22.2
11x7/16-14 UNC
104.8
6
165.1
106.390
14.3
25.4
11x1/2-13 UNC
133.4
8
209.5
139.735
15.9
28.6
11x5/8-11 UNC
171.4
11
279.4
196.885
17.5
34.9
11x3/4-10 UNC
235
15
381
285.8
19
41.3
12x7/8-9 UNC
330.2
20
520
412.8
20.6
47.6
12x1-8 UNC
463.6
Tapped holes in flange (outer bolt circle) without inner bolt circle
C
From taper 4
Type A1-A2 correspond ISO 702/I
D
B1
5
6
8
11
15
20
A
B
max
C
-0,025
D
G
F1
E2
F2
133.4
165.1
209.5
279.4
381
520
82.575
106.390
139.735
196.885
285.8
412.8
14.288
15.875
17.462
19.05
20.638
22.225
22.2
25.4
28.6
34.9
41.3
47.6
11x11.9
11x13.5
11x16.7
11x20.2
12x23.4
12x26.6
104.8
133.4
171.4
235
330.2
463.6
8x7/16-14 UNC
8x1/2-13 UNC
8x5/8-11 UNC
8x3/4-10 UNC
11x7/8-9 UNC
11x1-8 UNC
61.9
82.6
111.1
165.1
247.6
368.3
A
F2
B
Spindle nose
size
Through-holes in flange (outer bolt circle) tapped holes in inner bolt circle. From taper size 4 with driver
B2
G
7° 7' 30''
F1
E2
G
TYPE B1 - B2
C
D
From taper 4
Spindle nose
size
3
4
5
6
8
11
15
20
A
B
max
C
D
G
F1
92.1
108
133.4
165.1
209.5
279.4
381
520
53.985
63.525
82.575
106 .390
139.735
196.885
285.8
412.8
11.1
11.1
12.7
14.3
15.9
17.5
19
20.6
15.9
19
22.2
25.4
28.6
34.9
41,3
47.6
3x11.9
11x11.9
11x11.9
11x13,5
11x16.7
11x20.2
12x23.2
12x26.6
70.66
82.55
104.8
133.4
171.4
235
330.2
463.6
Through-holes in flange (outer bolt circle) without inner bolt circle
LONG TAPER
B
A
TYPE E L
Spindle nose size
A+0.051
B
C
D
L00
L0
L1
L2
L3
69.850
82.550
104.775
133.350
165.100
3 3/4-6 UNS
4 1/2-6 UNS
6-6 UNS
7 3/4-5 UNS
10 3/8-4 UNS
50.800
60.325
73.025
85.725
94.425
14.288
15.875
19.050
25.400
28.575
C
8° 17' 50''
D
http://www.bison-bial.com, e-mail:[email protected] tel.+48 857 416 420
94
Driving key
9.525x38.1
9.525x44.45
15.875x60.32
19.05x73.02
25.4x82.55

Similar documents

LATHE CHUCKS POWER CHUCKS AND HYDRAULIC

LATHE CHUCKS POWER CHUCKS AND HYDRAULIC 1 set of soft solid jaws 1 set of soft top jaws

More information

bison-bial sa

bison-bial sa PRECISION SELF-CENTERING 3- JAWS CHUCKS, HARD REVERSIBLE JAWS, I st CLASS ACCURACY, STEEL BODY

More information

lathe chucks independent chucks

lathe chucks independent chucks Reversible claw-type top jaws, standard design, tongue and groove, middle sized clamping range, 1 piece, hardened

More information

lathe chucks independent chucks

lathe chucks independent chucks Machining Rotating/ Stationary Clamping Clamping force Speed max. Precision

More information

Orange Line

Orange Line Due to this, workpieces with different diameters can be clamped without changing or shifting the jaws. Vibration isolation body made of iron cast Scroll drop-forged, balanced, hardened With one set...

More information

Fenner Electric Motors - Fenner Power Transmission

Fenner Electric Motors - Fenner Power Transmission latest European electric motor efficiency standards. The range is available from 63 to 71 frame in Aluminium, IE2 and Cast Iron, from 80 to 315L frame in IE3 premium efficiency.

More information