Benefits of Therm-E Pad Insulation
Transcription
Benefits of Therm-E Pad Insulation
Benefits of Therm-E Pad Insulation: • Time Tested In Real World Applications • Independently Lab Tested • Will Not off gas or Absorb Odors • 99.9% PURE Aluminum CORE • Carpet Slides EASILY OVER SURFACE DURING INSTALL • Light Weight, MADE FROM RECYCLED POLYETHYLENE AND ALUMINUM • EXCELLENT THERMAL BARRIER FOR COLD CONCRETE FLOORS • WILL NOT WICK MOISTURE or ABSORB CLEANING FLUIDS USED ON CARPET • Made In the USA by the Manufacturer of ESP Low-E® Insulation E nvironmentally Safe Products Inc. 313 West Golden Ln. New Oxford, PA 17350 Phone: 800-289-5693 Fax: (717)-624-7089 [email protected] · www.low-e.com Therm-E Pad Insulation Product Information ALL TESTING NUMBERS DONE ON 3/8’’ PAD , 1/2’’ PAD ALSO AVAILABLE 30 sq yd rolls 4’ x 67.5’ GENERIC TESTING IN ACCORDANCE TO HUD / FHA UM 72 a WEIGHT 7.8 OZS. / SQ YD THICKNESS .355’’ DENSITY 1.8 LBS / CU. FT - Non comparable to polyurethane foam / rebond COMPRESSION FORCE DEFLECTION @ 25% 3.5 PSI TENSILE STRENGTH 69.6 PSI ELONGATION 194% CLOSED CELL polyethylene CONSTRUCTION OF THERM-E PAD ALLOWS EXCELLENT COMPRESSION RECOVERY . 20,000 FOOT CYCLE TEST TEST METHOD CONDUCTED : ASTM D 6119 PRACTICE FOR CREATING SURFACE APPEARANCE CHANGES IN PILE YARN FLOOR COVERING FROM FOOT TRAFFIC TEST METHOD CONDUCTED : CRI TM-101 ASSESSMENT OF CARPET SURFACE APPEARANCE CHANGE USING CRI REFERENCE SCALES KEY TO RATINGS DONE ON 20,000 FOOT CYCLE TEST 1 SEVERE CHANGE 2 CONSIDERABLE CHANGE 3 MODERATE CHANGE 4 SLIGHT CHANGE 5 NO CHANGE AVERAGE PAR RATING 3.8 PERCENTAGE THICKNESS CHANGE AFTER TEST -3.1 % TESTING SHOWS THERM-E PAD PERFORMED ABOVE AVERAGE as COMPARED TO TRADITIONAL CARPET PAD IN THIS REAL WORLD TEST METHOD . THERM-E PAD INSTALLATION INSTRUCTIONS INSTALLING THERM-E PAD IS QUITE EASY COMPARED TO OLDER CONVENTIONAL CARPET PADDING . THERM-E PAD IS EASY TO MANEUVER INTO THE DESIRED FLOORING POSITION BECAUSE OF ITS LIGHT WEIGHT AND SMOOTH SURFACE FINISH . THERM-E PAD CAN BE USED ON ANY BASE FLOORING BUT IS ESPECIALLY EFFECTIVE ON COLD CONCRETE FLOORS WHERE A THERMAL BREAK IS NEEDED . IT WILL STOP THE HEAT DRAW FROM A COLD SLAB FLOOR . THERM-E PAD WILL HELP THAT COLD BASEMENT TO FEEL MORE LIVABLE, ESPECIALLY UNDER FOOT . BECAUSE OF THERM-E PAD’S UNIQUE QUALITIES THERE ARE A FEW VERY IMPORTANT GUIDELINES THAT MUST BE OBSERVED , ALTHOUGH IT IS INSTALLED JUST LIKE REGULAR CARPET PAD . 1 . NEVER INSTALL THERM-E PAD ON A FUNCTIONING RADIANT FLOOR SYSTEM . THERM-E PAD IS A THERMAL BLOCK AND WILL HELP TO REDUCE RADIANT HEAT TRANSFER . 2. WE DO NOT RECOMMEND INSTALLING THERM-E PAD ON A NEWLY POURED CONCRETE FLOOR OR A CONCRETE FLOOR THAT HAS NOT FULLY CURED . CONCRETE GIVES OFF MOISTURE AS IT CURES . THERM-E PAD IS WATERPROOF AND IS A TOTAL VAPOR BARRIER , THESE QUALITIES ARE EXCELLENT AS FAR AS NOT ABSORBING SPILLS ON CARPET , PET ACCIDENTS , ODORS , AND HARBORING BACTERIAL AND FUNGI GROWTH . LIKE ANY CARPET PAD INSTALL ALWAYS BE SURE TO START APPLICATION WITH A DRY CLEAN SURFACE FOR GOOD ADHESIVE ACTION . 3. WE RECOMMEND USING A STRONG ADHESIVE SPRAY OR CEMENT TO ATTACH THERM-E PAD TO CONCRETE AND STAPLES ON WOOD FLOORING OR ANY COMBINATION OF THE TWO REMEMBERING THAT THE FLOOR SURFACE MAY SOME DAY BE RE-EXPOSED . 4.BE SURE THAT SEAMS ARE TIGHTLY MATCHED AND USE A HIGH QUALITY DUCT TAPE TO CONNECT THERM-E PAD SEAMS . 5. AFTER CARPET HAS BEEN EASILY SLID OVER THERM-E PAD BE SURE TO USE A BOARD UNDER CARPET WHEN IRONING CARPET CONNECTION SEAMS . THIS PRACTICE IS COMMON WITH CARPET INSTALLERS BUT NOT ALWAYS OBSERVED . BECAUSE OF THERM-E PAD’S UNIQUE CLOSED CELL POLYETHYLENE FOAM CORE AN IRON BOARD IS HIGHLY RECOMMENDED AS NOT TO ACCIDENTLY CAUSE SURFACE MELT. PRODUCT LIABILITY DISCLAIMER PENDING INDEPENDENT CARPET MANUFACTURERS FULL ENDORSEMENTS , ESP INC., WILL NOT BE HELD LIABLE OR PARTY TO ANY WARRANTY CLAIMS ON CARPET PERFORMANCE BASED ON THERM -E PAD’S CHARACTERISTICS OR PROPERTIES BEING USED AS AN UNDERLAYMENT . ESP INC. ALSO WILL NOT BE HELD LIABLE FOR ANY DAMAGE TO FLOORING SURFACES OR SURROUNDING MATERIALS CAUSED BY MISAPPLICATION OR IMPROPER INSTALL OF PRODUCT . Dealer Information 8064