production of qcs operator station on windows 7

Transcription

Document Title: PRODUCTION OF QCS
OPERATOR STATION ON WINDOWS 7
USING EXPPLUS
Where Used: 09588010
Document #
6510030098
REV
02
Page 1 of 37
Contents
1
About this document ...................................................................................................................... 3
1.1
Hardware ................................................................................................................................ 3
1.1.1
Dell Precision T5500 Work Station Views .................................................................... 3
1.1.2
T5500 Operator Station Back Panel Connectors and Card Slot details ......................... 4
2
Creating QCS Operator Station on Dell T5500 Platform .............................................................. 6
2.1
BIOS....................................................................................................................................... 6
2.1.1
Configuring the BIOS settings ....................................................................................... 6
2.1.2
General Settings ............................................................................................................. 7
2.1.3
Drives Settings ............................................................................................................... 8
2.1.4
System Configuration Settings....................................................................................... 8
2.1.5
Security Settings............................................................................................................. 9
2.1.6
Power Management settings........................................................................................... 9
2.1.7
Post Behavior settings .................................................................................................. 10
2.2
RAID configuration.............................................................................................................. 10
2.2.1
Starting the RAID Configuration Program .................................................................. 10
2.3
Installation of Operating System using Experion PKS R400 system Initialization Media.. 11
2.3.1
Generating the Configuration Files for Target Machine .............................................. 11
2.3.2
Installing the Operating System on the Target Machine using Experion PKS R400
System Initialization Media ......................................................................................................... 18
2.4
Creating Boot media............................................................................................................. 22
2.5
Monitor Connection settings ................................................................................................ 22
2.6
Display Properties configuration.......................................................................................... 23
2.6.1
Display Properties Configuration for Single Monitor.................................................. 23
2.6.2
Display Properties Configuration for Dual Monitor .................................................... 26
2.7
Roxio Burning Software....................................................................................................... 30
2.7.1
Installation of Roxio Burning Software ....................................................................... 30
2.7.2
Roxio Burning Software Settings................................................................................. 33
2.8
Installing the RAE ................................................................................................................ 35
3
Additional Information................................................................................................................. 36
3.1
BIOS Update utility.............................................................................................................. 36
3.1.1
Installing the appropriate BIOS on R400.x platform ................................................... 36
Senior Manager,
Engineering:
Harish Gopalan
DATE: September 30, 2011
6510430198 Rev 00
Manager, Engineering:
DCC:
RJ Garside
DATE:
DATE:
Originator:
Anirudh Verma
DATE: September 30, 2011
Original Date Issued: Nov 29, 2010
USING EXPPLUS
Document #
6510030098
REV
02
Page 2 of 37
Related documents
6510020334 - Real-Time Application Environment (RAE) R600 for Experion PKS R400.2 Release and
Installation Notes
51154481 - Experion PKS System Initialization Media Software Change Notice
46027201 - Ghost Backup for Da Vinci and MXProLine Systems user guide
EP-DSX256 - Fault Tolerant Ethernet Installation and Service Guide
EPDCSX36 – Software Installation Users Guide
EPDCX506 – Supplementary Installation Tasks Guide
Revision history
Rev
DCN#
Date
Author
Description of Changes
00
20832
29-Nov-2010
Halappa Begurappa
Barun Paul
Anirudh Verma
New document released.
01
20895
04-Jan-2011
Halappa Begurappa
Barun Paul
Anirudh Verma
Updated the procedure and screen shots
in the Display Properties configuration
chapter.
02
20970
30-Sep-2011
Halappa Begurappa
Barun Paul
Anirudh Verma
Updated the document with Experion
PKS R400 system Initialization media
R100.3 changes and BIOS update
Utility.
Honeywell Proprietary and Confidential DO NOT COPY
USING EXPPLUS
Document #
6510030098
REV
02
Page 3 of 37
1 About this document
This document provides instructions on production of QCS Operator Station on Windows 7 by using
the Experion PKS system Initialization media (EXP Plus).
The instructions are applicable to Dell Precision T5500 (Non RAID) Workstations.
For QCS Operator Station, Non RAID based Dell T5500 with single
NOTE: hard disks is used.
1.1
Hardware
For more information about Dell Precision T5500 (Non RAID) workstation, see section 1.1.1.
1.1.1 Dell Precision T5500 Work Station Views
Figure 1-1 T5500 Operator Station Front and Back View
Table 1-1 T5500 Operator Station connection description
Sl. No.
Device
Comments
1
Optical drives (2)
This configuration contains one DVD+/-RW drive
2
Link integrity light
-
3
Headphone connector
-
4
Microphone connector
-
5
Power button, power light
-
6
Dell rotatable badge
-
7
Diagnostic lights (4)
-
USING EXPPLUS
Document #
6510030098
Page 4 of 37
8
USB 2.0 connectors (2)
-
9
Drive activity light
-
10
Flex bay
This configuration does not contain a floppy drive
11
Optical drive eject button
-
12
Power supply diagnostic light
-
13
Power supply diagnostic
button
-
14
Power Connector
15
Back Panel connectors
16
Expansion card slots (6)
17
Cover-release latch and
padlock ring
-
1.1.2 T5500 Operator Station Back Panel Connectors and Card Slot details
Below section provides back panel connector and card slot details of Dell T5500.
Figure 1-2 T5500 Operator Station Back Panel Connectors
REV
02
USING EXPPLUS
Document #
6510030098
Page 5 of 37
Table 1-2 T5500 Operator Station back panel connection description
Sl. No.
Connections Details
Remarks
1
Parallel connector
-
2
PS/2 mouse connector
-
3
eSATA connector
-
4
Line-out connector
-
5
Network activity light
-
6
Network adapter connector
-
7
Link integrity light
-
8
Line-in connector
-
9
USB 2.0 connectors (6)
-
10
PS/2 keyboard connector
-
11
Serial connector
-
Figure 1-3 T5500 Tower card slot details
Table 1-3 T5500 Operator Station card slot details
Slot No.
Type
Description
Slot-1
PCI Express x16 Slot
Wired as x8
Slot for Installing Network card For
FTE-Dual Port Intel Pro 1000 PT
Ethernet
Slot-2
Slot for Installing Video controller –
NVIDIA Quadro NVS295
Slot-3
PCI Express x16 Slot Wired as x8
-
Slot-4
-
Slot-5
PCI
-
Slot-6
PCI X
-
REV
02
USING EXPPLUS
Document #
6510030098
REV
02
Page 6 of 37
2 Creating QCS Operator Station on Dell T5500 Platform
To create an Operator Station on Dell T5500 platform, using Experion PKS R400 system
Initialization media, you must perform the following tasks.
Table 2-1 T5500 Operator Station configuration steps
Task
See Section
Completed?
2.1.1

RAID configuration
2.2

Installation of Operating System using Experion
PKS R400 system Initialization Media
2.3
Creating Boot media
2.4

Monitor Connection settings
2.5

Display Properties configuration
2.6

Roxio Burning Software
2.7

Installing the RAE
2.8

Configuring the BIOS settings
2.1


BIOS
2.1.1 Configuring the BIOS settings
The Dell workstation comes with BIOS configuration
ATTENTION: settings based on the Honeywell CFI. However, it is
recommended to verify, and reconfigure the same if needed.
The Dell workstation comes with Custom BIOS installed and it
is
recommended not to install any other version of the BIOS
CAUTION:
manually.
To configure the BIOS settings
1. Start the computer.
2. Press F2 as the computer boots to enter the setup utility.
The Dell Inc. Precision Workstation T5500 dialog box for BIOS settings appears.
USING EXPPLUS
Document #
6510030098
REV
02
Page 7 of 37
Figure 2-1 T5500 Operator Station Bios setting
2.1.2 General Settings
1. Expand Settings > General > Boot Sequence.
The Boot Sequence information is displayed in the right pane. The Boot sequence;
must be in the following order.
 Onboard or USB CD-ROM Drive.
 SATA0-SAMSUNG HD161GJ
Based on the manufacturer, the Hard Drive (HD) name listed under
NOTE: the Boot Sequence may vary.
Figure 2-2 T5500 Operator Station Boot Sequence
USING EXPPLUS
Document #
6510030098
REV
02
Page 8 of 37
If necessary, you can change the order of the Boot Sequence by
NOTE:
using the
button.
2.1.3 Drives Settings
1. Expand Settings >Drives > SATA Operation.
The SATA Operation information is displayed in the right pane.
2. From SATA Operation, select RAID Autodetect / AHCI.
A message box appears prompting you to confirm the selection made.
3. Click Yes to continue.
Figure 2-3 T5500 Operator Station RAID setting
2.1.4 System Configuration Settings
1. Expand Settings > System Configuration > Integrated NIC.
The Integrated NIC information is displayed in the right pane.
2. Under Integrated NIC, make sure it is Disable for systems with FTE connection.
For the systems with FTE connections ensure Network Adapter 1000
NOTE: PT Dual Port has been installed in the computer
Figure 2-4 T5500 Operator Station Integrated NIC setting
3. For systems, which does not intended for FTE use, make sure to Enable the same.
USING EXPPLUS
Document #
6510030098
Page 9 of 37
2.1.5 Security Settings
After the System Configuration settings are complete continue with the Security settings.
4. Expand Settings > Security > Administrator Password.
The Administrator Password information is displayed in the right pane.
5. In the Administrator Password
 Type the new password as hmxresult.
 Type the new password again to confirm.
 Click OK.
Figure 2-5 T5500 Operator Station Administrator password setting
6. Expand Settings > Security > Chassis Intrusion.
The Chassis Intrusion information is displayed in the right pane.
7. From Chassis Intrusion, select Enable.
Figure 2-6 T5500 Operator Station Chassis Intrusion setting
2.1.6 Power Management settings
1. Expand Settings > Power Management > AC Recovery.
The AC Recovery information is displayed in the right pane.
2. From AC Recovery, select Last Power State.
REV
02
USING EXPPLUS
Document #
6510030098
REV
02
Page 10 of 37
Figure 2-7 T5500 Operator Station AC Recovery setting
2.1.7 Post Behavior settings
1. Expand Settings > Post Behavior > Fast Boot.
The Fast Boot information is displayed in the right pane.
2. From Fast Boot, clear the Enable Fast Boot option.
3. After completing all the BIOS settings click Apply and then click Exit. The system
will restart automatically.
2.2
RAID configuration
2.2.1 Starting the RAID Configuration Program
As Operator Station use Non RAID Dell T5500 computers, this section is NOT applicable to
Operator Station.
In Non RAID Dell T5500, after the system restart, the message
NOTE: prompting you to press <Ctrl+I> does not appear.
USING EXPPLUS
Document #
6510030098
2.3
REV
02
Page 11 of 37
Installation of Operating System using Experion PKS R400 system Initialization
Media
Users must use Experion PKS System Initialization R100.x (or
Later) media along with HPS Operating System
Reinstallation media to install Windows 7 operating system on
the Honeywell qualified Dell Precision T5500 (Non RAID)
CAUTION: Workstation (MLK) machines.
For detailed information on above media refer to the latest Experion
PKS System Initialization Media Software Change Notice (SCN).
2.3.1 Generating the Configuration Files for Target Machine
2.3.1.1
Prerequisites


2.3.1.2
You need a standalone computer with CD/DVD ROM and Windows OS (Win2k3
or Win2k8 or Win XP or Win 7) to generate the configuration files for the target
machine.
The configuration files generated on the standalone computer must be saved in a
pen drive or on any removable disk as a backup. You need to use this
configuration file along with Experion PKS R400 system Initialization Media on
the target machine.
Generation of Configuration Files
Perform the following steps on the standalone computer to generate the configuration file for the
target machine.
Acknowledge the user account control dialog box, if it appears. It is
not necessary or mandatory for the user account control dialog box
NOTE: to appear during the installation process. This information is
applicable for the remainder of this manual, unless explicitly stated
otherwise.
1. Insert the Experion PKS R400 System Initialization media into the CD/DVD drive of
the standalone computer (not the target computer).
The Honeywell- Experion PKS System Initialization Media dialog box appears.
USING EXPPLUS
Document #
6510030098
Page 12 of 37
Figure 2-8 Experion PKS System Initialization Media Dialog box
2. Click Launch Setup.
3. Click Yes, id the User Account Control dialog box appears.
The Initializing Experion PKS System Installer... message appears.
The Experion PKS System Initialization Wizard appears.
REV
02
USING EXPPLUS
Document #
6510030098
REV
02
Page 13 of 37
Figure 2-9 Experion PKS System Initialization R100.3 Dialog manager for generating Configuration file
4. Select Generate Configuration files.
5. Click Next.
If the configuration files are already generated for the target
machine, select Modify existing configuration files. Click Browse
to browse to the configuration files and select the
NOTE: InitMediaOptions.xml file. Click Next. The subsequent dialog
boxes are displayed according to the selections made as per the
configuration files. You can modify the selections if required.
The Platform Configuration dialog box appears.
USING EXPPLUS
Document #
6510030098
REV
02
Page 14 of 37
Figure 2-10 Experion PKS System Initialization R100.3 Dialog manager for Platform Configuration
6. Select the following in Platform Configuration:
 From Choose Configuration, select Reinstall OS and Configure System in
Platform Configuration.
 Uncheck the Product Installation option.
This check box must be unchecked since OS Installation need to be
NOTE: taken up first.



From Select Platform, select Workstation and select the Dell Model for the target
machine from the drop-down list.
From Select Operating System, select Client and choose the Windows 7
Professional from drop-down list.
Click Next.
The Operating System Configuration dialog box appears.
USING EXPPLUS
Document #
6510030098
REV
02
Page 15 of 37
Figure 2-11 Experion PKS System Initialization R100.3 Dialog manager for OS Configuration
7. Select the following in the System Settings:
 Select the Local Language from the drop-down list.
 Select the Time Zone from the drop-down list appropriate to the geographical
location where the system is used.
 Type the Computer Name
Naming restrictions
 The computer name must be 15 characters or less in length and should begin
with an alphabetic character (“a to z” or “A to Z”) and cannot contain spaces or
other non-standard characters.
 All other nodes including non-redundant Servers Must Not end with the letters
A or B.
 Type the Company Name.
 Type the Customer Name.
For the Company Name and Customer Name do not use special
NOTE: characters.
 Type the Workgroup Name.
8. In the Account and Password, enter the following details:
 User Account Name (QCSAdmin)
 Password (Hmxresult1#) and confirm the password.
USING EXPPLUS
Document #
6510030098
REV
02
Page 16 of 37
9. Uncheck the Microsoft Embedded COA (Certificate Of Authenticity) is not
available on this platform check box. By doing this you need not enter the product
key.
10. Click Next.
The Network and Input/Output Devices Configuration dialog box appears.
For the systems with FTE connections ensure to install Intel Pro 1000
NOTE: PT Dual Port Network adapter.
Figure 2-12 Experion PKS System Initialization R100.3 Dialog manager for Network and I/O device Configuration
11. For configuring the systems with FTE, proceed with Step 13.
12. For configuring the system with Ethernet, select the Network Type as Ethernet, select
the No. of Adapters as One from the drop-down list and Network Link Speed as 100
mbps Full Duplex.
13. In the Network Configuration select the following:
 Select the Network Type as FTE for systems with FTE
 Select No. of Adapters as Two for systems with FTE
 The configuration of a network port can be changed by selecting it and clicking the
TCP/IP Properties for NIC button.
14. In the I/O details ensure the following settings are selected:
 Single monitor option.
 1280x1024 resolution option.
15. In the FTE Configuration
 Type the Multicast Address
USING EXPPLUS
Document #
6510030098




REV
02
Page 17 of 37
Type the Device Index
Type the UDP Source Port
Type UDP Destination Port
Provide a Friendly Name
For detailed information about FTE installation and configuration
NOTE: refer to Fault Tolerant Ethernet Installation and Service Guide - FE05400 (Document ID: EP-DSX256).
16. Click Next.
17. Read through the Confirmation Configuration Summary details, and click Save
Config.Files.
Figure 2-13 Experion PKS System Initialization R100.3 Dialog manager Confirmation box
To save the config files, browse through one of the following options.
a. You can either use USB flash drive, or local hard disk to save the configuration
files to be used on this computer for future use. OR
b. Save the generated configuration files in a separate folder at the root of the C
drive, floppy drive, or USB drive.
18. Click OK.
The Experion PKS System Initialization dialog box appears indicating that
Configuration files are saved successfully.
USING EXPPLUS
Document #
6510030098
REV
02
Page 18 of 37
19. Click OK.
20. Click Finish.
21. Read the instructions on the Honeywell Experion PKS System Initialization R100.3
- DialogManager
22. Click OK.
23. Close the Honeywell- Experion PKS System Initialization window.
2.3.2 Installing the Operating System on the Target Machine using Experion PKS
R400 System Initialization Media
1. In the target machine, insert Experion PKS R400 System Initialization media, connect
the USB flash drive that has the configuration file created for the target machine in
Section 2.3.1 and re-start the computer.
Ensure that the USB drive containing the configuration files
NOTE: generated for the target machine is connected before you re-start the
computer to avoid any removable disc detection.
2. Watch the monitor while it restarts and press any key when you see the message Press
any key to boot from CD or DVD.
USING EXPPLUS
Document #
6510030098
REV
02
Page 19 of 37
The Windows is loading files message appears.
The Experion PKS System Initialization Pre-Install Utility Window appears.
Figure 2-14 Experion PKS System Initialization Pre-Installation Utility Dialog Box
3. Click Browse and select the path where the configuration file is present.
4. Select InitMediaOptions.xml files.
5. Click Open.
USING EXPPLUS
Document #
6510030098
REV
02
Page 20 of 37
Figure 2-15 Experion PKS System Initialization Pre-Installation Utility to browse configuration file
6. Click Next.
The Experion PKS System Initialization Pre-Install Utility dialog box appears.
Figure 2-16 Experion PKS System Initialization Pre-Installation Utility to provide configuration details
7. In the Configuration details, select the following:
 Partitions count as Two from the drop-down list.
 Type the size of Primary partition as 70.
8. Select DVD as the appropriate location for installation media.
9. Click Next.
The Notice of Licensed Software dialog box appears.
USING EXPPLUS
Document #
6510030098
REV
02
Page 21 of 37
Figure 2-17 Experion PKS System Initialization Pre-Installation Utility showing Honeywell end user License
Agreement
10. Read the license agreement and select I accept the terms in the license agreement.
11. Click Install.
A warning message appears indicating that the disk contents and partition will be
deleted.
12. Click Yes to continue.
13. The Experion PKS System initialization preparing for Operating System
installation dialog box appears.
A message appears prompting to insert the Windows 7 Reinstallation DVD.
14. Remove the Experion PKS System Initialization media and insert the HPS
operating system reinstallation media for Windows 7.
15. Click OK.
The Installing Windows…dialog box displays the status of the Operating System
installation.
16. During the Operating System installation, your computer restarts several times.
17. After the Operating System installation is completed, a message appears prompting
you to insert the Experion PKS System Initialization R100.3 DVD.
USING EXPPLUS
Document #
6510030098
REV
02
Page 22 of 37
18. Remove the Windows 7 Reinstallation media and insert the Experion PKS System
Initialization R100.3 media and click OK.
The Initializing Experion PKS System Installer... message appears.
19. After the initial personalized settings are completed, The Experion PKS-Status
Display dialog box appears, displaying the status of the Operating System
Configuration.
A message appears in the Experion PKS-Status Display dialog box confirming the
Experion PKS System Initialization Installation is completed successfully.
20. Click OK to restart the system.
21. After the system restarts, login to the machine as QCSAdmin and verify the OS
installation.
2.4
Creating Boot media
Windows PE Boot media is needed to run the Norton ghost application on this RAE node for creating
its Ghost image (GHO file). You can use the same media to restore Ghost Images that are taken
already.
Use the computer which has Windows Operating System and the
NOTE: CD/DVD Burning Software installed for creating the Boot Media.
Refer the Ghost Backup for Da Vinci and MXProLine Systems
NOTE: user guide (46027201) for more details on using Norton Ghost on
RAE node.

2.5
Use the burning software to burn a Boot Media CD from the Production
DVD_124\OSDeployment\01000936_REVC_winpe.iso image.
Monitor Connection settings
NVS295 Display adapter card consists of two DP ports. When you set up the dual video
configurations, the Lower DP port is set as the Primary Video and the Upper DP port is set as the
Secondary Video.
A DP to DVI-D adapter converter can be used to convert the DP signal of NVS295 to DVI-D signal
for monitor. For this purpose, the monitor must support the DVI-D signal and must have an
appropriate signal cable.
USING EXPPLUS
Document #
6510030098
REV
02
Page 23 of 37
Figure 2-18 Monitor connection settings for NVIDIA Quadro NVS295
A DP to VGA adapter converter can be used to convert the DP signal of NVS295 to VGA signal for
monitor. The monitor must support the VGA signal and must have an appropriate signal cable.
2.6
Display Properties configuration
This section provides the procedure to configure the display properties.
2.6.1 Display Properties Configuration for Single Monitor
To configure the display properties for a computer using a single monitor
1. Right-click on the desktop, and then click Personalize from the shortcut menu.
The Personalization dialog box appears.
USING EXPPLUS
Document #
6510030098
Figure 2-19 Personalization Dialog box showing Display configuration settings
2. Select Display under See also.
The Display dialog box appears.
Figure 2-20 Monitor Display Dialog box showing Display settings
3. Select Smaller-100% (default) option.
4. Click Change display settings.
Page 24 of 37
REV
02
USING EXPPLUS
Document #
6510030098
REV
02
Page 25 of 37
The Screen Resolution dialog box appears.
Figure 2-21 Screen resolution settings Dialog box
5. Under Resolution, move the Slider to set a screen resolution of 1280x1024 in dropdown list.
6. Click Advanced settings.
The Generic PnP Monitor and NVIDIA Quadro NVS 295 Properties dialog box
appears.
Figure 2-22 Monitor and NVIDIA Quadro NVS Properties showing Screen Refresh rate and color Settings
USING EXPPLUS
Document #
6510030098
REV
02
Page 26 of 37
7. Click the Monitor tab.
8. Under Monitor settings, set the Screen refresh rate based on type of monitor you are
using, as follows:
 For LCD Monitors – 60 Hertz.
 For non-LCD Monitors – 75 Hertz
9. Under Colors, select High Color (16-bit).
10. Click Apply.
The Display Settings message appears, prompting you to keep the display settings
you have configured.
11. Click Yes.
12. Click OK to save the monitor settings and close the dialog box.
13. Click OK to close the Screen Resolution dialog box.
14. Close the Display dialog box.
2.6.2 Display Properties Configuration for Dual Monitor
When T5500 System is used with dual monitors, first configure the display settings for a single
monitor, see section 2.6.1, and then configure the display settings for the second monitor.
To configure the Display settings for the second monitor
1. Connect both the Monitors to the NVIDIA Quadro NVS 295 card.
2. Right-click on the desktop, and then click Personalize from the shortcut menu.
The Personalization dialog box appears.
USING EXPPLUS
Document #
6510030098
Figure 2-23 Personalization Dialog box showing Display configuration settings
3. Select Display under See also.
The Display dialog box appears.
Figure 2-24 Monitor Display Dialog box showing Display settings
4. Select Smaller-100% (default) option.
5. Click Change display settings.
The Screen Resolution dialog box appears.
Page 27 of 37
REV
02
USING EXPPLUS
Document #
6510030098
REV
02
Page 28 of 37
Figure 2-25 Screen resolution and monitor settings Dialog box
6. Under Display Select the Second Monitor.
7. Under Resolution, move the Slider to set a screen resolution of 1280x1024 in dropdown list.
8. Under Multiple displays select Extend these displays.
9. Click Advanced settings.
The Generic PnP Monitor and NVIDIA Quadro NVS 295 Properties dialog box
appears.
USING EXPPLUS
Document #
6510030098
REV
02
Page 29 of 37
Figure 2-26 Monitor and NVIDIA Quadro NVS Properties showing Screen Refresh rate and color Settings
10. Click the Monitor tab.
11. Under Monitor settings, set the Screen refresh rate based on type of monitor you are
using, as follows:
 For LCD Monitors – 60 Hertz.
 For non-LCD Monitors – 75 Hertz
12. Under Colors, select High Color (16-bit).
13. Click Apply.
The Display Settings message appears, prompting you to keep the display settings
you have configured.
14. Click Yes.
15. Click OK to save the monitor settings and close the dialog box.
16. Click OK to close the Screen Resolution dialog box.
17. Close the Display dialog box.
USING EXPPLUS
Document #
6510030098
2.7
REV
02
Page 30 of 37
Roxio Burning Software
2.7.1 Installation of Roxio Burning Software
Honeywell recommends to install Roxio Burning Software in your computer.
To install the Roxio Burning Software
1. Insert the Roxio Burning Software media provided along with the T5500 machine into
the CD/DVD ROM-drive.
2. The Autorun setup wizard appears.
The Welcome to the Setup Wizard for Roxio Creator DE 10.3 Setup appears.
Figure 2-27 Roxio Creation DE 10.3 Setup Dialog box
3. Click Next.
The License Agreement dialog box appears.
USING EXPPLUS
Document #
6510030098
REV
02
Page 31 of 37
Figure 2-28 Roxio Creation DE 10.3 Setup Dialog box showing License Agreement
4. Read the License and Agreement, and then click I accept the terms in the License
Agreement.
5. Click Next.
The Customer Information dialog box appears.
6. Click Next.
The Choose Setup Type dialog box appears.
Figure 2-29 Roxio Creation DE 10.3 Setup Dialog box showing Installation Setup Type
7. Click Custom.
8. Click Next.
The Install Location dialog box appears.
USING EXPPLUS
Document #
6510030098
REV
02
Page 32 of 37
Figure 2-30 Roxio Creation DE 10.3 Setup Dialog box showing Install Location
9. Click Next.
The Custom Setup dialog box appears.
Figure 2-31 Roxio Creation DE 10.3 Setup Dialog box showing Custom Setup
10. By default all the features that will be installed are selected. However, you must clear
the check boxes for the features that must not be installed, and ensure to select ONLY
the following features:
 Roxio Creator Tools
 Roxio Creator Data
 Roxio Creator Copy
11. Click Next.
USING EXPPLUS
Document #
6510030098
REV
02
Page 33 of 37
The Ready to Install dialog box appears.
12. Click Install.
After the installation is complete, the Roxio Creator DE 10.3 Setup complete wizard
dialog box appears.
Figure 2-32 Roxio Creation DE 10.3 Setup Dialog box showing Setup Wizard completed
13. Click Finish.
A message appears, prompting you to restart the computer.
14. Click Yes. The computer will restart.
2.7.2 Roxio Burning Software Settings
To configure Roxio Burning Software settings
1. Choose Start > Programs > Roxio Creator DE > Home.
The Roxio Product Registration dialog box appears.
2. Click Cancel.
A message appears, prompting you to confirm the cancellation of the product
registration.
USING EXPPLUS
Document #
6510030098
REV
02
Page 34 of 37
This message may be displayed in different languages, depending
NOTE: on your regional settings.
3. Select Don’t Show Me This Again.
4. Click OK.
The Creator DE 10.3 window appears.
Figure 2-33 Roxio Creation DE 10.3 Dialog box
5. On the Tools menu, click Options.
The Options dialog box appears.
Figure 2-34 Roxio Creation DE 10.3 setting in the Option Dialog box
6. Select General in the left pane.
The General setting details are displayed in the right pane.
7. Under Startup, clear the Check for updates check box.
8. Select Data and Backup in the left pane.
USING EXPPLUS
Document #
6510030098
REV
02
Page 35 of 37
The Data setting details are displayed in the right pane.
Figure 2-35 Roxio Creation DE 10.3 setting in the Option Dialog box
9. Under CD Recording Options, perform the following:
 In the Type list, select Disc at Once (DAO), Closed from drop-down list.
 In the Mode list, select Mode 1 from drop-down list.
 In the File System list, select ISO+Joliet (102 character file names) from dropdown list.
10. Under Write-Once DVD Compatibility, select I only need to use discs for one
recording option.
11. Click OK to close the Options dialog box.
12. Close the Creator DE 10.3 window.
2.8
Installing the RAE
For installing RAE R600 on this Operator Station, refer to Real-Time Application Environment (RAE)
R600 with Experion R400.2 Release and Installation Notes p/n 6510020334.
USING EXPPLUS
Document #
6510030098
3
REV
02
Page 36 of 37
Additional Information
This section provides additional information related to Operating System loading after major
hardware recovery such as Mother Board failure.
3.1
BIOS Update utility
The BIOS Update utility selects Dell’s or Honeywell’s custom BIOS to support/protect operating
system activation. Honeywell’s custom BIOS files are derived from generic Dell BIOS files and are
mandatory to complete automatic activation of the operating system for platforms that are installed
using Honeywell OEM embedded operating systems.
The BIOS Update utility updates the BIOS either to a new
version or to any of the previous versions. This is a new
ATTENTION: feature introduced in Experion PKS System Initialization
R100.3 onwards.
You are recommended to use the BIOS Update utility only in
CAUTION: case of motherboard failure or motherboard replacement.
The following table lists the platform names and the model numbers with which the BIOS Update
utility must be used.
Platform
T5500
Part Number
6543100031
6543100030
In case of motherboard failure, below steps needs to be carried out in order to bring back the server to
operation:
1. Replace the motherboard.
2. Complete the motherboard installation.
3. Switch on the platform.
4. Run the BIOS Update utility by referring Section 3.1.1 Installing the appropriate
BIOS on R400.x platform.
3.1.1 Installing the appropriate BIOS on R400.x platform
Before starting the BIOS Update utility installation, save all
CAUTION: data and close all windows.
After the installation platform needs a restart.
USING EXPPLUS
Document #
6510030098
REV
02
Page 37 of 37
Perform the following steps to run the BIOS Update utility on R400.x platforms.
1. Log on to the platform with administrator privileges.
2. Insert Experion PKS System Initialization R100.3 (or Later) media into DVD
drive.
3. Browse to <root>\webpage\autorun.htm path.
4. Double-click autorun.htm
The Experion PKS System Initialization On-media documentation dialog box is
displayed.
5. In the left pane, click BIOS
The BIOS Minimum Requirements screen is displayed in the right pane.
6. In the right pane, click platformname.exe from the BIOS upgrade application
column.
For example, if you are upgrading BIOS version for the R710 platform, click
R710.exe file.
7. Save the platformname.exe to your local folder.
8. Browse to the folder containing the installer and double-click WinZipSelfExtractor<platform name.exe>
9. Click Allow and click Setup.
The BIOS Update dialog box is displayed that contains information about the
installed BIOS version and the latest custom BIOS version.
The installed BIOS version and the package version
displayed in the BIOS Update dialog box varies depending
ATTENTION: on the server or workstation on which you are performing
the installation.
10. Click Yes to continue with the BIOS update installation.
11. Click OK to restart the platform after completing the installation.
Do not click Cancel on the WinZip Self Extractor-<platform
name.exe>
dialog box or close the WinZip Self ExtractorCAUTION:
<platform name.exe> dialog box during installation.
The BIOS update occurs immediately after the platform is restarted.
Information about the BIOS modification is displayed on the screen.
Subsequently, the installed BIOS version is displayed in the Power On Self Test
(POST) screen. You can also check the BIOS version by pressing F2 once the POST
screen closes.

production of qcs operator station on windows 7

Transcription

Similar documents

USA Yeast, Hattiesburg, MS

50-9104 - VisionPRO 8000 Thermostat

M-Line 4500

AnimatorDV Simple+ Quick Start

Vendmaster Brochure

States, Robert J.

Honeywell SuperOne 3205

BattleNet 360 - Delex Systems, Inc

Bios Buzz March 18, 2016 - Rollins School of Public Health

907283 - 5635-6635 SX-DX Turbo Skid Loaders Operator`s Manual.tif