Vector V10S - Designplan Lighting

Transcription

Vector V10S
79 Trenton Avenue
Frenchtown, NJ 08825
Tel: (908) 996-7710
Fax: (908) 996-7042
SPECIFIERS GUIDE
Overview
Vector V10S
Key Features
≤ 1149lm/m 350lm/ft
≤ 13w/m 4w/ft
Ultra-slim aluminium profile just 6.8mm high by 10.5mm (0.4in) wide with a single
strip PCB using LEDs in White Spectrum™ or EQ™ performance grades.
High output V10S-13 model gives up to 1149lm per metre (350lm/ft) output while
V10S-07 model provides up to 634lm per metre (193lm/ft).
Ideally suited to concealed lighting applications such as coving, uplighting, shelves,
under ledges etc.
Length increments of 100mm (4in) up to 2005mm (6ft 7in) with plug-and-play
interconnectors allowing longer light runs. The unique rotation mount allows up to
90º rotation for light throw adjustment.
≤ 88lm/w
≤ 88 CRI
2600 - 5000K CCT
CLICK-CONNECT
PowerTHRU
24VDC CV
IPX0
Specification Codes
Codes
03
06
09
12
LENGTH
12.01" (305 MM)
23.82" (605 MM)
35.63" (905 MM)
47.44" (1205 MM)
POWER FEED
C 1.9" PowerTHRU
D 1.9" Single Feed
G 19.6" PowerTHRU
H 19.6" Single Feed
V 1 0 S- C B A 2 0 -C 1 C C B
LED CCT
C
D
F
G
H
B
E
2600K WS
2900K WS
3300K WS
3800K WS
5000K WS
2670-2870K EQ
3020-3220K EQ
LED
CONNECTORS
1G 07 WM
1C 13 WM
A
B
No Connectors
CLICK-CONNECT
Applications
V10S is ideally suited
to concealed lighting
applications such as
coving, uplighting,
shelves and under
counter details.
Images clockwise from top:
1. Concealed ceiling cove
Corinthia Hotel
London
2. Concealed coving detail
Raouls Restaurant
London
3. Illuminated ceiling slot
Double Tree Hilton Hotel
London
4. Backlit bar shelving
Ormer Restaurant
Jersey
Application Guides
45
°
6.89" (175)
40°
6.89" (175)
Concealed Coving
5.51" (140)
2.76" (70)
18.7" (475)
6.89" (175)
20°
40°
6.89" (175)
18.7" (475)
5.51" (140)
2.76" (70)
3.15" (80)
2.76" (70)
30°
2.76" (70)
20°
3.66" (93)
1.65"
4.41" (112)
2.17"
Under Shelf
*Contact Lumino for full details of SolidEdge system.
Performance
Performance Table 13W /3.28'
V10S-13
lumens1 /3.28' lumens1 /w watts2 /3.28' CRI
CCT
R9
2670 - 2870K
792
60
13.2
81
+31
2600K
852
65
13.2
88
+56
2900K
1047
79
13.2
60
-49
3300K
999
75
13.2
81
+30
3800K
1149
87
13.2
69
-17
5000K
1120
86
13.2
65
-53
1
Maximum total LED lumens per metre excluding LOR factor.
2
Power rated at 24vdc. Data @25°C Ta
V10S-07
Performance Table 7W /3.28'
lumens1 /3.28' lumens1 /w watts2 /3.28' CRI
CCT
R9
2670 - 2870K
356
52
6.9
80
+31
2600K
472
68
7.0
88
+61
2900K
569
79
7.2
60
-49
3300K
588
83
7.0
67
-23
3800K
634
88
7.2
69
-17
5000K
680
97
7.0
63
-73
1
Maximum total LED lumens per metre excluding LOR factor.
2
Power rated at 24vdc. Data @25°C Ta
Light output ratio
LED
1.00 LOR
110º beam angle
3-Chip 5450 SMT package
V10-13: 0.657" mounting pitch
V10-07: 0.984" mounting pitch
Photometric Data
x
4.70
y
4.75
4.80
30°
0°
30°
120°
120°
90°
90°
4.15
2600K
4.10
150cd
2 SDCM
4.05
60°
60°
C90°
C0°
250cd
30°
CIE 1931 X & Y Chromaticity
hrs 10,000
30,000
30°
Polar Distribution*
50,000
lm%
120
100
80
L70
60
40
0°
max cd
C19°
ft
fc
1.64'
74
3.28'
18
4.92'
8
6.56'
5
8.20'
3
49,500hrs
20
9.84'
2
dh
dv
Lumen maintenence* @25°C Ta
Illuminance at a distance*
Lumen output tests conducted by the National Physical Laboratory.
Additional testing and photometric data conducted by independent UKAS
accredited test laboratory, LUX-TSI. Test duration approx 60 minutes at
ambient temperature of 24C with 24 hour burn-in time. Stabilisation period,
approx. 30 minutes. Humidity <65%RH. Voltage 24.00VDC, current 0.578A.
*Testing on production sample V10 3300K 505mm 13w/3.28'.
Rotation Mount
Dimensions
mount ~1g (0.4 oz)
V10S ~120g (4.2 oz)
-per 3.28' (1000mm)
0.55" (14mm)
90°
0.77" (19.5mm)
Three rotation mounts per 3.28' average recommended. Fixing hole diameter 0.16" (4.2mm). Screw gauge
size #4 max. head size 0.32" (8.2mm) dia. max. recommended. See Accessories & Options page for
order codes.
Full 90° Rotation
Mounting
4.72" (120mm)
min.
Concealed Coving
)
mm
(50 .
"
7 in
1.9 m
Straights / Corners / Curves
Dimensions
Standard lengths
0.34" (8.80)
0.49" (12.50)
~110g per 3.28'
XX05
12.01" (305mm)
23.82" (605mm)
35.63" (905mm)
0.27" (6.80)
0.41" (10.50)
0.30" (7.50)
*other lengths
available on request.
0.89" (22.50)
47.44" (1205mm)*
0.31" (7.80)
Options & Accessories
CLICK-CONNECT
Powerfeeds options
CB - 1.97" (50mm) WIRE PowerThru
GB - 19.69" (500mm) WIRE PowerThru
HB - 19.69" (500mm) WIRE Single
No Connector Powerfeeds options
CA - 1.97" (50mm) WIRE PowerThru No Connector
GA - 19.69" (500mm) WIRE PowerThru No Connector
HA - 19.69" (500mm) WIRE Single No Connector
VECA-CA901-R1
Pair of 3M Scotchlok™ IDC sealant connectors
0.6"x0.3"x0.3" (15.0 x 7.0 x 7.0 mm)
CLICK-CONNECT
Extenders
VECA-CA025-R1 - 9.84" (250mm)
VECA-CA100-R1 - 39.4" (1000mm)
Mounting
V10S-MA620-R1 V10S Rotation Mount PC White (20 pack)
Double Sided Tape
V10S-MA180-R1
V10S Double-Sided Self Adhesive Tape 0.23" (6mm) Width
x 25M (82')
Drivers & Dimming
Wiring
V10S can be installed in power-through configuration lengths up to 19.6' subject to maximum cable
size and length. Longer lengths can easily be achieved by running a parallel feed as shown in the
29.5' example below. Use only with maximum output 24 VDC voltage Class 2 power unit.
19.7' (6m) example
80W
24VDC
4.92'
4.92'
4.92'
4.92'
4.92'
4.92'
29.5' (9m) example
4.92'
4.92'
4.92'
4.92'
120W
24VDC
Voltage
V10S is rated to operate at 24VDC constant voltage. Its full operating range is 19.3 to 25.6 VDC.
Start-voltage is defined as the voltage measured at the furthest cable point away from the driver.
When calculating maximum cable size and length limits, installers must make their own checks to
ensure that the minimum start voltage is correct as shown in the table below.
V10S-13/07 Minimum start voltage
V10S-13/07 Loading
V10S
Length
min. start
voltage
V10S
Length
V10-13
A
V10-07
A
> 3.28'
> 6.56'
> 9.84'
> 13.1'
> 16.4'
> 19.7'
20.3 VDC
20.6 VDC
21.1 VDC
21.8 VDC
22.8 VDC
23.9 VDC
> 3.28'
> 6.56'
> 9.84'
> 13.1'
> 16.4'
> 19.7'
0.55
1.10
1.65
2.20
2.75
3.30
0.30
0.60
0.90
1.20
1.50
1.80
24VDC
Minimum start-voltage check point
1-10V / DALI / DMX
V10S is ideally suited to dimming (via a PWM interface) with a 1-10V, DALI or DMX control signal.
Maximum cable size and distance should be adjusted if using a dimming interface as shown in the
wiring example tables. Typical PWM interfaces can handle 5A allowing a maximum of 29.5' of
V10S-13 or 52.5' of V10S-07 per interface.
Dimming
Control
24VDC
59.25" (1505mm)
Interface
max. 6.56'
Drivers
Drivers must be of constant voltage type providing 24VDC power supply. Recommended minimum
driver ratings are shown in the table above. It is recommended that only drivers with overload and
short-circuit protection are used. Use only with maximum output 24 VDC voltage Class 2 power unit.
Recommended minimum driver rating
V10S
Length
V10-13
A
Driver
VA
V10-07
A
Driver
VA
>13.1'
>19.7'
>29.5'
>39.4'
>52.5'
2.2A
3.3A
5.0A
6.6A
8.8A
60W
80W
120W
160W
220W
1.2A
1.8A
2.7A
3.6A
4.8A
30W
45W
65W
90W
120W
Installation Notes
24VDC power supplies and dimming interfaces are often tested and verified to be EMI compliant with secondary cable lengths of up to
32.8' (shorter lengths on some devices). For cable lengths exceeding 3.28', EMI emissions should be verified in the application. When EMI
emissions exceed the allowed levels it may be possible to reduce them by using ferrite cores (not supplied).
24VDC cables should be shielded if longer than 32.8' total length. Recommended maximum cable lengths for dimmed circuits are
based on a typical dimming interface voltage drop of 0.3V. Installers should check the specific voltage drop of the interface they are
using and adjust cable length accordingly.
*Recommended cable lengths shown are based on average resistance for typical copper solid core cables. Cable characteristics may vary
acording to manufacturer, temperature, copper purity, connections etc. Installers must make their own checks to ensure that the minimum
start voltage is correct. The start-voltage check point is located at the furthest cable point from the driver.
Wiring Examples
V10S-13 Switched
40W
24VDC
59.25"
59.25"
265' max. [0.06in²]
80W
24VDC
~10' max.
78.94"
78.94"
9.84' max. [0.1in²]
78.94"
~20' max.
Cable size & maximum cable distance*
V10S
Length
0.02in²
20AWG
0.03in²
18AWG
0.04in²
17AWG
0.06in²
15AWG
0.1in²
13AWG
>3.28'
>6.56'
>9.84'
>13.1'
>16.4'
>19.7'
328'
157'
88'
49'
23'
3'
492'
236'
131'
72'
32'
3'
656'
315'
177'
98'
46'
3'
984'
472'
265'
147'
69'
6'
1640'
787'
443'
246'
115'
10'
V10S-13 Dimmed
Dimming
Control
40W
24VDC
59.25"
Interface
59.25"
236' max. [1.5mm²]
~10' max.
Dimming
Control
80W
24VDC
Interface
78.94"
78.94"
6.56' max. [0.1in²]
78.94"
~19.7' max.
V10S
Length
0.02in²
0.03in²
0.04in²
0.06in²
0.1in²
20AWG
18AWG
17AWG
15AWG
13AWG
>3.28'
>6.56'
>9.84'
>13.1'
>16.4'
>19.7'
301'
137'
78'
42'
16'
-
452'
206'
118'
62'
23'
3'
603'
275'
157'
85'
32'
3'
905'
413'
236'
124'
46'
3'
1509'
689'
393'
210'
78'
6'
V10S-07 Switched
25W
24VDC
59.25"
472' max. [1.5mm²]
60W
24VDC
59.25"
~10' max.
78.94"
78.94"
13.1" max. [0.1in²]
78.94"
~19.7' max.
V10S
Length
0.02in²
20AWG
0.03in²
18AWG
0.04in²
17AWG
0.06in²
15AWG
0.1in²
13AWG
>3.28'
>6.56'
>9.84'
>13.1'
>16.4'
>19.7'
590'
282'
157'
92'
39'
3'
886'
423'
236'
134'
59'
3'
1181'
564'
315'
180'
78'
6'
1771'
846'
472'
272'
118'
6'
2952'
1410'
787'
452'
197'
13'
V10S-07 Dimmed
Dimming
Control
25W
24VDC
59.25"
Interface
59.25"
~10' max.
276' max. [0.06in²]
Dimming
Control
60W
24VDC
Interface
78.93"
78.93"
78.93"
~19.7' max.
9.84' max. [0.1in²]
V10S
Length
0.02in²
20AWG
0.03in²
18AWG
0.04in²
17AWG
0.06in²
15AWG
0.1in²
13AWG
>3.28'
>6.56'
>9.84'
>13.1'
>16.4'
>19.7'
551'
249'
137'
75'
26'
3'
826'
374'
206'
115'
42'
3'
1102'
498'
275'
151'
55'
3'
1653'
748'
413'
226'
82'
6'
2756'
1246'
689'
377'
137'
9'
LED Specification
White Spectrum™ LED
Vector LEDs with White Spectrum™ technology benefit from ultra-fine LED x,y bining coordinates
to precise specifications. Testing and control of these specifications gives very accurate control of
correlated colour temperatures (CCT). White Spectrum™ technology also allows us to offer our high
colour rendering index rating of 88 CRI (Ra) as standard for 2600K products.
Each 2600K Vector LED is ultra-fine binned from a defined x, y range bin area covering approximately
2 MacAdam steps. This is far smaller than the ANSI C78.377A Standard which equates to 7 MacAdam steps. This binning accuracy equates to a colour temperature precision of less than 2.0%
tolerance giving approximately +/- 50K.
White Spectrum™ is one of the leading global LED technologies. A typical warm white fine-bin from
another manufacturer is typically at least 40% larger than Lumino’s White Spectrum™ ultra-fine binning.
VECTOR 2600K
2-step MacAdam
0.43
ANSI C78.377A 2700K
7-step MacAdam
0.39
0.41
0.43
26
280
00
K
0K
0.41
0.45
0.47
0.49
eQ™ LED
To compliment Lumino’s White Spectrum ultra-fine bining, eQ™ offers wider binning within defined
tolerances. eQ™ gives specifiers more choice and provides an economical solution where ultra-fine
bining is not essential for a project. Available in 2670-2870K and 3020-3220K, eQ™ can be specified for V10S-13 and V10S-07.
Technology
Material specifications
T6 6063 Aluminium extrusion
Injection moulded polycarbonate end caps
PCB electroplated copper foil on FR4 substrate
22AWG wires stranded copper / PVC
Operating environment
Running Temperature (Tc):
Ambient Temperature (Ta):
Storage Temperature:
Ingress Protection rating:
Ave. 17°C above Ta
-40 to +60°C
-40 to +100°C
IPX0
IPX0
Certification Standards
IEC 60598-2-4:1997 Luminaires used in conjuction with IEC 60598-1:2008
IEC 62031:2008 LED Modules for general lighting
GOST R IEC 60598-2-4:1999 Luminaires used in conjuction with GOST R IEC 60598-1:2011
GOST R IEC 62031
EN55015: 2006+A1 :2007
EN61547: 1995+A1 :2000
Following the provisions of EMC Directive 2004/108/EC
CB Testing Laboratory: Intertek Product Safety Laboratory (UK)
UL Certified US/CA E364314
Low-voltage Lighting Systems, Power Units, Luminaires and Fittings
Vector V10S
79 Trenton Avenue
Frenchtown, NJ 08825
Tel: (908) 996-7710
Fax: (908) 996-7042
SG-V10S-WHI-R1310

Vector V10S - Designplan Lighting

Transcription

Similar documents

vector v10s - Lumino Lighting